Table of Contents
- XPS 13 2-in-1 (9310 2n1) Service Manual
- Working inside your computer
- Removing and installing components
- Drivers and downloads
- System setup
- Troubleshooting
- Getting help and contacting Dell
DELL 9310 2-in-1 User Manual
Displayed below is the user manual for 9310 2-in-1 by DELL which is a product in the Notebooks category. This manual has pages.
Related Manuals
XPS 13 2-in-1 (9310 2n1)
Service Manual
Regulatory Model: P103G
Regulatory Type: P103G002
November 2020
Rev. A01
Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use of your product.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid
the problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
© 2020 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other
trademarks may be trademarks of their respective owners.
Chapter 1: Working inside your computer...................................................................................... 5
Before working inside your computer.............................................................................................................................5
Safety instructions.............................................................................................................................................................. 5
Electrostatic discharge—ESD protection..................................................................................................................... 6
ESD field service kit ...........................................................................................................................................................6
Transporting sensitive components................................................................................................................................ 7
After working inside your computer................................................................................................................................7
Chapter 2: Removing and installing components........................................................................... 8
Recommended tools........................................................................................................................................................... 8
Screw list............................................................................................................................................................................... 8
Major components of XPS 13 2-in-1 (9310 2n1)...........................................................................................................9
Base cover............................................................................................................................................................................11
Removing the base cover........................................................................................................................................... 11
Installing the base cover.............................................................................................................................................13
Battery.................................................................................................................................................................................. 14
Lithium-ion battery precautions................................................................................................................................14
Removing the battery................................................................................................................................................. 15
Installing the battery....................................................................................................................................................16
Display assembly.................................................................................................................................................................18
Removing the display assembly................................................................................................................................ 18
Installing the display assembly..................................................................................................................................20
Speakers.............................................................................................................................................................................. 22
Removing the speakers..............................................................................................................................................22
Installing the speakers................................................................................................................................................ 23
System board..................................................................................................................................................................... 24
Removing the system board..................................................................................................................................... 24
Installing the system board........................................................................................................................................27
Keyboard assembly........................................................................................................................................................... 30
Removing the keyboard assembly........................................................................................................................... 30
Installing the keyboard assembly............................................................................................................................. 32
Palm-rest assembly...........................................................................................................................................................35
Removing the palm-rest assembly.......................................................................................................................... 35
Installing the palm-rest assembly............................................................................................................................ 35
Chapter 3: Drivers and downloads............................................................................................... 37
Chapter 4: System setup............................................................................................................. 38
BIOS overview....................................................................................................................................................................38
Entering BIOS setup program........................................................................................................................................ 38
Navigation keys..................................................................................................................................................................38
Boot Sequence...................................................................................................................................................................39
System setup options.......................................................................................................................................................39
Clearing CMOS settings.................................................................................................................................................. 48
Contents
Contents 3
Clearing BIOS (System Setup) and System passwords.......................................................................................... 48
Chapter 5: Troubleshooting.........................................................................................................49
Locate the Service Tag or Express Service Code of your Dell computer ..............................................49
Recovering the operating system................................................................................................................................. 49
SupportAssist | On-board Diagnostics.........................................................................................................................49
System diagnostic lights..................................................................................................................................................50
Flashing the BIOS...............................................................................................................................................................51
Flashing BIOS (USB key)................................................................................................................................................. 51
WiFi power cycle................................................................................................................................................................ 51
Flea power release............................................................................................................................................................ 52
Chapter 6: Getting help and contacting Dell................................................................................ 53
4 Contents
Working inside your computer
Before working inside your computer
About this task
NOTE: The images in this document may differ from your computer depending on the configuration you ordered.
Steps
1. Save and close all open files and exit all open applications.
2. Shut down your computer. Click Start > Power > Shut down.
NOTE: If you are using a different operating system, see the documentation of your operating system for shut-down
instructions.
3. Disconnect your computer and all attached devices from their electrical outlets.
4. Disconnect all attached network devices and peripherals, such as keyboard, mouse, and monitor from your computer.
CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the
cable from the network device.
5. Remove any media card and optical disc from your computer, if applicable.
Safety instructions
Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless
otherwise noted, each procedure included in this document assumes that you have read the safety information that shipped
with your computer.
WARNING: Before working inside your computer, read the safety information that is shipped with your
computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
WARNING: Disconnect your computer from all power sources before opening the computer cover or panels.
After you finish working inside the computer, replace all covers, panels, and screws before connecting your
computer to an electrical outlet.
CAUTION: To avoid damaging the computer, ensure that the work surface is flat, dry, and clean.
CAUTION: To avoid damaging the components and cards, handle them by their edges, and avoid touching the
pins and the contacts.
CAUTION: You should only perform troubleshooting and repairs as authorized or directed by the Dell technical
assistance team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. See the
safety instructions that is shipped with the product or at www.dell.com/regulatory_compliance.
CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal
surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal
surface to dissipate static electricity which could harm internal components.
1
Working inside your computer 5
CAUTION: When you disconnect a cable, pull it by its connector or its pull tab, not the cable itself. Some cables
have connectors with locking tabs or thumbscrews that you must disengage before disconnecting the cable.
When disconnecting cables, keep them evenly aligned to avoid bending the connector pins. When connecting
cables, ensure that the ports and the connectors are correctly oriented and aligned.
CAUTION: Press and eject any installed card from the media-card reader.
NOTE: The color of your computer and certain components may appear differently than shown in this document.
Electrostatic discharge—ESD protection
ESD is a major concern when you handle electronic components, especially sensitive components such as expansion cards,
processors, memory DIMMs, and system boards. Very slight charges can damage circuits in ways that may not be obvious, such
as intermittent problems or a shortened product life span. As the industry pushes for lower power requirements and increased
density, ESD protection is an increasing concern.
Due to the increased density of semiconductors used in recent Dell products, the sensitivity to static damage is now higher than
in previous Dell products. For this reason, some previously approved methods of handling parts are no longer applicable.
Two recognized types of ESD damage are catastrophic and intermittent failures.
●Catastrophic – Catastrophic failures represent approximately 20 percent of ESD-related failures. The damage causes an
immediate and complete loss of device functionality. An example of catastrophic failure is a memory DIMM that has received
a static shock and immediately generates a "No POST/No Video" symptom with a beep code emitted for missing or
nonfunctional memory.
●Intermittent – Intermittent failures represent approximately 80 percent of ESD-related failures. The high rate of
intermittent failures means that most of the time when damage occurs, it is not immediately recognizable. The DIMM
receives a static shock, but the tracing is merely weakened and does not immediately produce outward symptoms related to
the damage. The weakened trace may take weeks or months to melt, and in the meantime may cause degradation of memory
integrity, intermittent memory errors, etc.
The more difficult type of damage to recognize and troubleshoot is the intermittent (also called latent or "walking wounded")
failure.
Perform the following steps to prevent ESD damage:
●Use a wired ESD wrist strap that is properly grounded. The use of wireless anti-static straps is no longer allowed; they do
not provide adequate protection. Touching the chassis before handling parts does not ensure adequate ESD protection on
parts with increased sensitivity to ESD damage.
●Handle all static-sensitive components in a static-safe area. If possible, use anti-static floor pads and workbench pads.
●When unpacking a static-sensitive component from its shipping carton, do not remove the component from the anti-static
packing material until you are ready to install the component. Before unwrapping the anti-static packaging, ensure that you
discharge static electricity from your body.
●Before transporting a static-sensitive component, place it in an anti-static container or packaging.
ESD field service kit
The unmonitored Field Service kit is the most commonly used service kit. Each Field Service kit includes three main components:
anti-static mat, wrist strap, and bonding wire.
Components of an ESD field service kit
The components of an ESD field service kit are:
●Anti-Static Mat – The anti-static mat is dissipative and parts can be placed on it during service procedures. When using an
anti-static mat, your wrist strap should be snug and the bonding wire should be connected to the mat and to any bare metal
on the system being worked on. Once deployed properly, service parts can be removed from the ESD bag and placed directly
on the mat. ESD-sensitive items are safe in your hand, on the ESD mat, in the system, or inside a bag.
●Wrist Strap and Bonding Wire – The wrist strap and bonding wire can be either directly connected between your wrist
and bare metal on the hardware if the ESD mat is not required, or connected to the anti-static mat to protect hardware that
is temporarily placed on the mat. The physical connection of the wrist strap and bonding wire between your skin, the ESD
6Working inside your computer
mat, and the hardware is known as bonding. Use only Field Service kits with a wrist strap, mat, and bonding wire. Never use
wireless wrist straps. Always be aware that the internal wires of a wrist strap are prone to damage from normal wear and
tear, and must be checked regularly with a wrist strap tester in order to avoid accidental ESD hardware damage. It is
recommended to test the wrist strap and bonding wire at least once per week.
●ESD Wrist Strap Tester – The wires inside of an ESD strap are prone to damage over time. When using an unmonitored
kit, it is a best practice to regularly test the strap prior to each service call, and at a minimum, test once per week. A wrist
strap tester is the best method for doing this test. If you do not have your own wrist strap tester, check with your regional
office to find out if they have one. To perform the test, plug the wrist-strap's bonding-wire into the tester while it is
strapped to your wrist and push the button to test. A green LED is lit if the test is successful; a red LED is lit and an alarm
sounds if the test fails.
●Insulator Elements – It is critical to keep ESD sensitive devices, such as plastic heat sink casings, away from internal parts
that are insulators and often highly charged.
●Working Environment – Before deploying the ESD Field Service kit, assess the situation at the customer location. For
example, deploying the kit for a server environment is different than for a desktop or portable environment. Servers are
typically installed in a rack within a data center; desktops or portables are typically placed on office desks or cubicles. Always
look for a large open flat work area that is free of clutter and large enough to deploy the ESD kit with additional space to
accommodate the type of system that is being repaired. The workspace should also be free of insulators that can cause an
ESD event. On the work area, insulators such as Styrofoam and other plastics should always be moved at least 12 inches or
30 centimeters away from sensitive parts before physically handling any hardware components
●ESD Packaging – All ESD-sensitive devices must be shipped and received in static-safe packaging. Metal, static-shielded
bags are preferred. However, you should always return the damaged part using the same ESD bag and packaging that the
new part arrived in. The ESD bag should be folded over and taped shut and all the same foam packing material should be
used in the original box that the new part arrived in. ESD-sensitive devices should be removed from packaging only at an
ESD-protected work surface, and parts should never be placed on top of the ESD bag because only the inside of the bag is
shielded. Always place parts in your hand, on the ESD mat, in the system, or inside an anti-static bag.
●Transporting Sensitive Components – When transporting ESD sensitive components such as replacement parts or parts
to be returned to Dell, it is critical to place these parts in anti-static bags for safe transport.
ESD protection summary
It is recommended that all field service technicians use the traditional wired ESD grounding wrist strap and protective anti-static
mat at all times when servicing Dell products. In addition, it is critical that technicians keep sensitive parts separate from all
insulator parts while performing service and that they use anti-static bags for transporting sensitive components.
Transporting sensitive components
When transporting ESD sensitive components such as replacement parts or parts to be returned to Dell, it is critical to place
these parts in anti-static bags for safe transport.
After working inside your computer
About this task
CAUTION: Leaving stray or loose screws inside your computer may severely damage your computer.
Steps
1. Replace all screws and ensure that no stray screws remain inside your computer.
2. Connect any external devices, peripherals, or cables you removed before working on your computer.
3. Replace any media cards, discs, or any other parts that you removed before working on your computer.
4. Connect your computer and all attached devices to their electrical outlets.
5. Turn on your computer.
Working inside your computer 7
Removing and installing components
NOTE: The images in this document may differ from your computer depending on the configuration you ordered.
Recommended tools
The procedures in this document may require the following tools:
●Phillips screwdriver #00 (used for M1.6, M2 screw types)
●Phillips screwdriver #0 (used for M2.5 screw types)
●Torx screwdriver T5 (used for Torx screws)
●Plastic scribe
Screw list
NOTE: When removing screws from a component, it is recommended to note the screw type, the quantity of screws, and
then place them in a screw storage box. This is to ensure that the correct number of screws and correct screw type is
restored when the component is replaced.
NOTE: Some computers have magnetic surfaces. Ensure that the screws are not left attached to such surfaces when
replacing a component.
NOTE: Screw color may vary with the configuration ordered.
Table 1. Screw list
Component Secured to Screw type Quantity Screw image
Base cover Palm-rest assembly M2x4.5 (Torx
screw)
8
Battery System board M1.6x3.4 (Torx
screw)
1
Battery Palm-rest assembly M1.6x3 7
Battery Palm-rest assembly M1.2x4 2
Display-cable bracket System board M1.6x3 (captive
screw)
1
Display assembly Palm-rest assembly M2.5x3 4
Keyboard bracket (left) Palm-rest assembly M1.2x2.5 1
Keyboard bracket (right) Palm-rest assembly M1.2x2.5 1
2
8 Removing and installing components
Table 1. Screw list (continued)
Component Secured to Screw type Quantity Screw image
USB Type-C bracket System board M1.6x3 1
USB Type-C bracket System board M1.6x2 1
System board Palm-rest assembly M1.6x2.5 4
System board Palm-rest assembly M1.2x3 3
System board Palm-rest assembly M1.2x4 (captive
screw)
1
Keyboard assembly Palm-rest assembly M1.2x1.4 38
Keyboard assembly Palm-rest assembly M1.2x1.6 10
Major components of XPS 13 2-in-1 (9310 2n1)
The following image shows the major components of XPS 13 2-in-1 (9310 2n1).
Removing and installing components 9
1. Base cover
2. Battery
3. System board
4. Left fan
5. Left keyboard bracket
10 Removing and installing components
6. Palm-rest assembly
7. Left speaker
8. Display assembly
9. Right speaker
10. Keyboard assembly
11. USB Type-C port bracket
12. Right fan
NOTE: Dell provides a list of components and their part numbers for the original system configuration purchased. These
parts are available according to warranty coverages purchased by the customer. Contact your Dell sales representative for
purchase options.
Base cover
Removing the base cover
Prerequisites
1. Follow the procedure in Before working inside your computer.
About this task
The following images indicate the location of the base cover and provide a visual representation of the removal procedure.
Removing and installing components 11
12 Removing and installing components
Steps
1. Remove the eight Torx screws (M2x4.5) that secure the base cover to the palm-rest assembly.
2. Starting from the bottom-left corner, pry the base cover in the direction of the arrows to release it from the palm-rest
assembly.
CAUTION: Do not pull on or pry the base cover from the top as it may damage the base cover.
3. Hold both sides of the base cover and rotate from front to back to remove from palm rest assembly.
NOTE: The pins at the bottom of the base cover for grounding the antennas and the audio board are fragile. Place the
base cover on a clean surface to avoid damage to the pins.
Installing the base cover
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the base cover and provide a visual representation of the installation procedure.
Removing and installing components 13
Steps
1. Align and secure the back of the base cover on the palm-rest assembly, and then snap the base cover into place.
2. Replace the eight Torx screws (M2x4.5) that secure the base cover to the palm-rest assembly.
Next steps
1. Follow the procedure in After working inside your computer.
Battery
Lithium-ion battery precautions
CAUTION:
●Exercise caution when handling Lithium-ion batteries.
●Discharge the battery completely before removing it. Disconnect the AC power adapter from the system and
operate the computer solely on battery power—the battery is fully discharged when the computer no longer
turns on when the power button is pressed.
●Do not crush, drop, mutilate, or penetrate the battery with foreign objects.
●Do not expose the battery to high temperatures, or disassemble battery packs and cells.
14 Removing and installing components
●Do not apply pressure to the surface of the battery.
●Do not bend the battery.
●Do not use tools of any kind to pry on or against the battery.
●Ensure any screws during the servicing of this product are not lost or misplaced, to prevent accidental
puncture or damage to the battery and other system components.
●If the battery gets stuck inside your computer as a result of swelling, do not try to release it as puncturing,
bending, or crushing a lithium-ion battery can be dangerous. In such an instance, contact Dell technical
support for assistance. See www.dell.com/contactdell.
●Always purchase genuine batteries from www.dell.com or authorized Dell partners and resellers.
Removing the battery
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
About this task
The following image indicates the location of the battery and provides a visual representation of the removal procedure.
Removing and installing components 15
Steps
1. Remove the Torx 5 screw (M1.6x3.4) that secures the battery cable to the system board.
2. Disconnect the battery cable from the interposer board.
NOTE: Remove the interposer board immediately after disconnecting the battery cable to avoid misplacing it. Hold the
edges of the interposer board to avoid damaging the pins on it.
NOTE: The interposer board is not polarity sensitive and both sides are compatible.
3. Remove the interposer board from the system board.
4. Remove the seven screws (M1.6x3) that secure the battery to the palm-rest assembly.
5. Remove the two screws (M1.2x4) that secure the battery to the system board.
6. Lift the battery off the palm-rest assembly.
7. Turn the battery over.
8. Using a plastic scribe, push to remove the magnet and the metal bar from the battery.
NOTE: Keep the magnet and the metal bar as they need to be installed on the new battery.
Installing the battery
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the battery and provides a visual representation of the installation procedure.
16 Removing and installing components
Steps
1. Adhere the magnet and the metal bar to the battery.
NOTE: Install the magnet and the metal bar from the faulty battery.
2. Align the screw holes on the battery with the screw holes on the system board and palm-rest assembly.
3. Replace the two screws (M1.2x4) that secure the battery to the system board.
4. Replace the seven screws (M1.6x3) that secure the battery to the palm-rest assembly.
5. Place the interposer board to the connector on the system board.
NOTE: The interposer board is not polarity sensitive and both sides are compatible.
6. Connect the battery cable to the interposer board.
7. Replace the Torx 5 screw (M1.6x3.4) that secures the battery cable to the system board.
Next steps
1. Install the base cover.
2. Follow the procedure in After working inside your computer.
Removing and installing components 17
Display assembly
Removing the display assembly
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
3. Remove the battery.
About this task
The following images indicate the location of display assembly and provide a visual representation of the removal procedure.
18 Removing and installing components
Steps
1. Loosen the captive screw (M1.6x3) that secures the display-cable bracket to the system board.
2. Lift the display-cable bracket off the system board.
3. Peel the tapes that secure the display cable and camera cable to the system board.
4. Using the tape as a pull tab, disconnect the display cable and camera cable from the system board.
5. Remove the display cable and camera cable from the routing guides on the system board.
6. Remove the four screws (M2.5x3) that secure the display hinges to the palm-rest assembly.
7. Slide the palm-rest assembly off the display assembly.
Removing and installing components 19
Installing the display assembly
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of display assembly and provide a visual representation of the installation procedure.
20 Removing and installing components
Steps
1. Slide the palm-rest assembly under the display assembly.
2. Align the screw holes on the palm-rest assembly with the screw holes on the display hinges.
3. Replace the four screws (M2.5x3) that secure the display hinges to the palm-rest assembly.
4. Route the display cable and camera cable through the routing guides on the system board.
Removing and installing components 21
5. Connect the display cable and camera cable to the system board.
6. Adhere the tapes that secure the display cable and camera cable to the system board.
7. Align and place the display-cable bracket on the system board.
8. Tighten the captive screw (M1.6x3) that secures the display-cable bracket to the system board.
Next steps
1. Install the battery.
2. Install the base cover.
3. Follow the procedure in After working inside your computer.
Speakers
Removing the speakers
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
3. Remove the battery.
About this task
The following image indicates the location of speakers and provides a visual representation of the removal procedure.
Steps
1. Disconnect the speaker cable from the system board.
2. Note the routing of the speaker cable and remove the speaker cable from the routing guides on the palm-rest assembly.
3. Using a plastic scribe, pry the speakers off the palm-rest assembly.
22 Removing and installing components
Installing the speakers
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of speakers and provides a visual representation of the installation procedure.
Steps
1. Slide the speakers into the slots on the palm-rest assembly.
NOTE: Ensure that there is no adhesive residue from the faulty speakers that are removed previously.
2. Route the speaker cable through the routing guides on the palm-rest assembly.
3. Connect the speaker cable to the system board.
Next steps
1. Install the battery.
2. Install the base cover.
3. Follow the procedure in After working inside your computer.
Removing and installing components 23
System board
Removing the system board
Prerequisites
CAUTION: Back up all files on the solid-state drive (SSD) to an external storage device before getting your
device ready for service. The SSD is soldered onto the system board, and the service replacement board does
not have an operating system that is preinstalled on it.
Restore files from your backup after the device has been serviced with its reinstalled operating system.
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
3. Remove the battery.
About this task
The following image indicates the connectors on your system board.
Figure 1. System-board connectors
1. Speaker cable 2. Fingerprint-reader cable
3. Display cable 4. Camera cable
5. Keyboard-controller board cable
The following images indicate the location of system board and provide a visual representation of the removal procedure.
24 Removing and installing components
Removing and installing components 25
Steps
1. Loosen the captive screw (M1.6x3) that secures the display-cable bracket to the system board.
2. Lift the display-cable bracket off the system board.
3. Peel the tapes that secure the display cable and camera cable to the system board.
4. Using the tape as a pull tab, disconnect the display cable and camera cable from the system board.
26 Removing and installing components
5. Remove the display cable and camera cable from the routing guides on the system board.
6. Remove the screw (M1.6x3) and the screw (M1.6x2) that secures the type-C bracket to the system board.
NOTE: The M1.6x2 screw has a bigger head than the M1.6x3 screw.
7. Lift the type-C bracket off the system board.
8. Disconnect the speaker cable from the system board.
9. Open the latch and disconnect the fingerprint-reader cable from the system board.
10. Peel off the fingerprint-reader daughter-board from the system board.
11. Open the latch and disconnect the keyboard-controller board cable from the system board.
12. Remove the four screws (M1.6x2.5), three screws (M1.2x3), and one captive screw (M1.2x4) that secure the system board
to the palm-rest assembly.
13. Lift the system board off the palm-rest assembly.
14. Remove the power-button and fingerprint reader bracket from the palm-rest assembly.
15. Place the bracket and the system board on a dry, flat, and clean surface.
Installing the system board
Prerequisites
CAUTION: Back up all files on the solid-state drive (SSD) to an external storage device before getting your
device ready for service. The SSD is soldered onto the system board, and the service replacement board does
not have an operating system that is preinstalled on it.
Restore files from your backup after the device has been serviced with its reinstalled operating system.
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the connectors on your system board.
Figure 2. System-board connectors
1. Speaker cable 2. Fingerprint-reader cable
3. Display cable 4. Camera cable
5. Keyboard-controller board cable
The following images indicate the location of system board and provide a visual representation of the installation procedure.
Removing and installing components 27
28 Removing and installing components
Steps
1. Align and place the power-button and fingerprint reader bracket on the palm-rest assembly.
2. Align the screw holes on the system board with the screw holes on the palm-rest assembly.
3. Replace the fours screws (M2x4), three screws (M1.2x3), and one screw (M1.2x4) that secure the system board to the
palm-rest assembly.
4. Connect the keyboard-controller board cable to the system board and close the latch to secure the cable.
5. Connect the speaker cable to the system board.
6. Adhere the fingerprint-reader board to the slot on the system board.
7. Connect the fingerprint-reader cable to the system board and close the latch to secure the cable.
8. Align the screw holes on the USB Type-C bracket to the screw holes on the system board.
9. Replace the screw (M1.6x3) and the screw (M1.6x2) that secures the USB Type-C port bracket to the system board.
NOTE: The M1.6x2 screw has a bigger head than the M1.6x3 screw.
10. Route the display cable and camera cable through the routing guides on the system board.
11. Connect the display cable and camera cable to the system board.
Removing and installing components 29
12. Adhere the tapes that secure the display cable and camera cable to the system board.
13. Align and place the display-cable bracket on the system board.
14. Tighten the captive screw (M1.6x3) that secures the display-cable bracket to the system board.
Next steps
1. Install the battery.
2. Install the base cover.
3. Follow the procedure in After working inside your computer.
Keyboard assembly
Removing the keyboard assembly
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
3. Remove the battery.
4. Remove the system board.
About this task
The following images indicate the location of keyboard assembly and provide a visual representation of the removal procedure.
30 Removing and installing components
Removing and installing components 31
Steps
1. Peel the fingerprint reader cable from the keyboard.
2. Remove the speaker cable from the routing guides on the left keyboard bracket.
3. Loosen the captive screw (M1.2x2.5) that secures the left keyboard bracket to the palm-rest assembly.
4. Using a plastic scribe, pry the left keyboard bracket off the palm-rest assembly.
5. Loosen the captive screw (M1.2x2.5) that secures the right keyboard bracket to the palm-rest assembly.
6. Using a plastic scribe, pry the right keyboard bracket off the palm-rest assembly.
7. Disconnect the keyboard cable and keyboard backlight cable from the keyboard controller board.
8. Peel the keyboard controller board cable from the keyboard.
9. Remove the 38 screws (M1.2x1.4) and ten screws (M1.2x1.6) that secure the keyboard to the palm-rest assembly.
NOTE: Peel off the three copper foil from the palm-rest assembly, and then peel off the two conductive tapes on the
keyboard assembly to separate the keyboard assembly and the palm-rest assembly.
10. Lift the keyboard off the palm-rest assembly.
Installing the keyboard assembly
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of keyboard assembly and provide a visual representation of the installation
procedure.
32 Removing and installing components
Removing and installing components 33
Steps
1. Align the screw holes on the keyboard with the screw holes on the palm-rest assembly.
NOTE: Adhere the two conductive tapes on the keyboard, and then adhere the three copper foils on the palm-rest
assembly to secure the keyboard assembly to the palm-rest assembly.
2. Replace the 38 screws (M1.2x1.4) and ten screws (M1.2x1.6) that secure the keyboard to the palm-rest assembly.
NOTE: Do not install keyboard assembly screws into locations that are marked with MB. Those screw holes are reserved
for system board screws.
3. Adhere the keyboard controller board cable to the keyboard.
4. Connect the keyboard cable and keyboard backlight cable to the keyboard controller board.
5. Adhere the right keyboard bracket in the slots on the palm-rest assembly.
6. Tighten the captive screw (M1.2x2.5) that secures the right keyboard bracket to the palm-rest assembly.
7. Adhere the right keyboard bracket in the slots on the palm-rest assembly.
8. Tighten the captive screw (M1.2x2.5) that secures the left keyboard bracket to the palm-rest assembly.
9. Route the speaker cable through the routing guides on the left keyboard assembly.
10. Adhere the fingerprint reader cable to the keyboard.
Next steps
1. Install the system board.
2. Install the battery.
3. Install the base cover.
4. Follow the procedure in After working inside your computer.
34 Removing and installing components
Palm-rest assembly
Removing the palm-rest assembly
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
3. Remove the battery.
4. Remove the display assembly.
5. Remove the speakers.
6. Remove the system board.
7. Remove the keyboard assembly.
About this task
The following image indicates the palm-rest assembly and provides a visual representation of the removal procedure.
Steps
The palm-rest assembly is left after performing the steps in the prerequisites.
NOTE: Keep the power-button and fingerprint reader bracket if you must replace the palm-rest assembly as the bracket is
a separate service part for reuse.
NOTE: If the power-button and fingerprint reader bracket is not found on the palm-rest assembly, the bracket should be on
the system board.
Installing the palm-rest assembly
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
Removing and installing components 35
About this task
The following image indicates the palm-rest assembly and provides a visual representation of the installation procedure.
Steps
Place the palm-rest assembly on a flat surface.
NOTE: If you are installing components to a new palm-rest assembly, use the power-button and fingerprint reader bracket
from the previous palm-rest assembly.
Next steps
1. Install the keyboard assembly.
2. Install the system board .
3. Install the speakers.
4. Install the display assembly.
5. Install the battery.
6. Install the base cover.
7. Follow the procedure in After working inside your computer.
36 Removing and installing components
System setup
CAUTION: Unless you are an expert computer user, do not change the settings in the BIOS Setup program.
Certain changes can make your computer work incorrectly.
NOTE: Depending on the computer and its installed devices, the items listed in this section may or may not be displayed.
NOTE: Before you change BIOS Setup program, it is recommended that you write down the BIOS Setup program screen
information for future reference.
Use the BIOS Setup program for the following purposes:
●Get information about the hardware installed in your computer, such as the amount of RAM and the size of the hard drive.
●Change the system configuration information.
●Set or change a user-selectable option, such as the user password, type of hard drive installed, and enabling or disabling
base devices.
BIOS overview
The BIOS manages data flow between the computer's operating system and attached devices such as hard disk, video adapter,
keyboard, mouse, and printer.
Entering BIOS setup program
About this task
Turn on (or restart) your computer and press F2 immediately.
Navigation keys
NOTE: For most of the System Setup options, changes that you make are recorded but do not take effect until you restart
the system.
Table 2. Navigation keys
Keys Navigation
Up arrow Moves to the previous field.
Down arrow Moves to the next field.
Enter Selects a value in the selected field (if applicable) or follow
the link in the field.
Spacebar Expands or collapses a drop-down list, if applicable.
Tab Moves to the next focus area.
NOTE: For the standard graphics browser only.
Esc Moves to the previous page until you view the main screen.
Pressing Esc in the main screen displays a message that
prompts you to save any unsaved changes and restarts the
system.
4
38 System setup
Boot Sequence
Boot Sequence allows you to bypass the System Setup–defined boot device order and boot directly to a specific device (for
example: optical drive or hard drive). During the Power-on Self Test (POST), when the Dell logo appears, you can:
●Access System Setup by pressing F2 key
●Bring up the one-time boot menu by pressing F12 key
The one-time boot menu displays the devices that you can boot from including the diagnostic option. The boot menu options
are:
●Removable Drive (if available)
●STXXXX Drive (if available)
NOTE: XXX denotes the SATA drive number.
●Optical Drive (if available)
●SATA Hard Drive (if available)
●Diagnostics
The boot sequence screen also displays the option to access the System Setup screen.
System setup options
NOTE: Depending on this computer and its installed devices, the items that are listed in this section may or may not be
displayed.
Table 3. System setup options—System information menu
Overview
BIOS Version Displays the BIOS version number.
Service Tag Displays the Service Tag of the computer.
Asset Tag Displays the Asset Tag of the computer.
Ownership Tag Displays the ownership tag of the computer.
Manufacture Date Displays the manufacture date of the computer.
Ownership Date Displays the ownership date of the computer.
Express Service Code Displays the express service code of the computer.
Ownership Tag Displays the ownership tag of the computer.
Signed Firmware Update Displays whether the signed firmware update is enabled.
Battery Displays the battery health information.
Primary Displays the primary battery.
Battery Level Displays the battery level.
Battery State Displays the battery state.
Health Displays the battery health.
AC Adapter Displays whether an AC adapter is installed.
Processor Information
Processor Type Displays the processor type.
Maximum Clock Speed Displays the maximum processor clock speed.
Core Count Displays the number of cores on the processor.
Processor L2 Cache Displays the processor L2 Cache size.
Processor ID Displays the processor identification code.
System setup 39
Table 3. System setup options—System information menu (continued)
Overview
Processor L3 Cache Displays the processor L3 Cache size.
Current Clock Speed Displays the current processor clock speed.
Minimum Clock Speed Displays the minimum processor clock speed.
Microcode Version Displays the microcode version.
Intel Hyper-Threading Capable Displays whether the processor is Hyper-Threading (HT) capable.
64-Bit Technology Displays whether 64-bit technology is used.
Memory Information
Memory Installed Displays the total computer memory installed.
Memory Available Displays the total computer memory available.
Memory Speed Displays the memory speed.
Memory Channel Mode Displays single or dual channel mode.
Memory Technology Displays the technology that is used for the memory.
Device Information
Video Controller Displays the integrate graphics information of the computer.
Video BIOS Version Displays the video BIOS version of the computer.
Video Memory Displays the video memory information of the computer.
Panel Type Displays the Panel Type of the computer.
Native Resolution Displays the native resolution of the computer.
Audio Controller Displays the audio controller information of the computer.
Wi-Fi Device Displays the wireless device information of the computer.
Bluetooth Device Displays the Bluetooth device information of the computer.
Table 4. System setup options—Boot options menu
Boot options
Advanced Boot Options
Enable UEFI Network Stack Enables or disables UEFI Network Stack.
Default: OFF.
Boot Mode
Boot Mode: UEFI only Displays the boot mode of this computer.
Enable Boot Devices Enables or disables boot devices for this computer.
Boot Sequence Displays the boot sequence.
BIOS Setup Advanced Mode Enables or disables advanced BIOS settings.
Default: ON.
UEFI Boot Path Security Enables or disables the system to prompt the user to enter the Admin
password when booting a UEFI boot path from the F12 boot menu.
Default: Always Except Internal HDD.
Table 5. System setup options—System Configuration menu
System Configuration
Date/Time
40 System setup
Table 5. System setup options—System Configuration menu (continued)
System Configuration
Date Sets the computer date in MM/DD/YYYY format. Changes to the date take
effect immediately.
Time Sets the computer time in HH/MM/SS 24-hour format. You can switch
between 12-hour and 24-hour clock. Changes to the time take effect
immediately.
Storage Interface
Port Enablement Enables the selected onboard drives.
SATA Operation Configures operating mode of the integrated SATA hard drive controller.
Default: RAID. SATA is configured to support RAID (Intel Rapid Restore
Technology).
Drive Information Displays the information of various onboard drives.
Enable Audio Enables or disables all integrated audio controller.
Default: ON.
Enable Microphone Enables or disables microphone.
Default: ON.
Enable Internal Speaker Enables or disables internal speaker.
Default: ON.
USB Configuration
Enable Boot Support Enables or disables booting from USB mass storage devices such as external
hard drive, optical drive, and USB drive.
Default: ON.
Enable External USB Ports Enables or disables USB ports to be functional in an operating system
environment.
Default: ON.
Enable Thunderbolt Technology Support Enables or disables Thunderbolt Technology Support.
Default: ON.
Enable Thunderbolt Boot Support Enables or disables Thunderbolt Boot Support.
Default: OFF.
Miscellaneous Devices Enables or disables various onboard devices.
Enable Camera Enables or disables the camera.
Default: ON.
Touchscreen Enables or disables the touchscreen for the operating system.
NOTE: Touchscreen will always work in the BIOS setup irrespective of this
setting.
Default: ON.
Enable Fingerprint Reader Device Enables or disables the Fingerprint Reader Device.
Default: ON.
Enable Fingerprint Reader Single Sign On Enables or disables the Fingerprint Reader Device's Single Sign On capability.
Default: ON.
Enable MediaCard Enables to switch all media cards On/Off or set the media card to read-only
state.
System setup 41
Table 5. System setup options—System Configuration menu (continued)
System Configuration
Default: Enable Secure Digital (SD) Card.
Keyboard Illumination Configures the operating mode of the keyboard illumination feature.
Default: Bright. Enable the keyboard illumination feature at 100% brightness
level.
Keyboard Backlight Timeout on AC Configures the timeout value for the keyboard when an AC adapter is
connected to the computer. The keyboard backlight timeout value is only
effect when the backlight is enabled.
Default: 10 seconds.
Keyboard Backlight Timeout on
Battery
Configures the timeout value for the keyboard when the computer is running
on battery. The keyboard backlight timeout value is only effect when the
backlight is enabled.
Default: 10 seconds.
Table 6. System setup options—Video menu
Video
LCD Brightness
Brightness on battery power Sets the screen brightness when the computer is running on battery power.
Brightness on AC power Sets the screen brightness when the computer is running on AC power.
Table 7. System setup options—Security menu
Security
Enable Admin Setup Lockout Enables or disables the user from entering BIOS Setup when an Admin
Password is set.
Default: OFF.
Password Bypass Bypass the System (Boot) Password and the internal hard drive password
prompts during a system restart.
Default: Disabled.
Enable Non-Admin Password Changes Enables or disables the user to change the system and hard drive password
without the need for admin password.
Default: ON.
Non-Admin Setup Changes
Allow Wireless Switch Changes Enables or disables changes to the setup option when an Administrator
password is set.
Default: OFF.
Enable UEFI Capsule Firmware Updates Enables or disables BIOS updates through UEFI capsule update packages.
Absolute Enables, disables or permanently disable the BIOS module interface of the
optional Absolute Persistence Module service from Absolute Software.
Default: Enable Absolute.
TPM 2.0 Security On Select whether or not the Trusted Platform Model (TPM) is visible to the OS.
Default: ON.
PPI Bypass for Enable Commands Enables or disables the OS to skip BIOS Physical Presence Interface (PPI) user
prompts when issuing TPM PPI enabled and activate commands.
Default: OFF.
42 System setup
Table 7. System setup options—Security menu (continued)
Security
PPI Bypass for Disable Commands Enables or disables The OS to skip BIOS PPI user prompts when issuing TPM
PPI Disable and Deactivate commands.
Default: OFF.
PPI Bypass for Clear Commands Enables or disables the operating system to skip BIOS Physical Presence
Interface (PPI) user prompts when issuing the Clear command.
Default: OFF.
Attestation Enables Enables to control whether the TPM Endorsement Hierarchy is available to the
OS. Disabling this setting restricts the ability to use the TPM for signature
operations.
Default: ON.
Key Storage Enable Enables to control whether the TPM Endorsement Hierarchy is available to the
OS. Disabling this setting restricts the ability to use the TPM for storing owner
data.
Default: ON.
SHA-256 Enables or disables the BIOS and the TPM to use the SHA-256 hash algorithm
to extend measurements into the TPM PCRs during BIOS boot.
Default: ON.
Clear Enables or disables the computer to clear the PTT owner information, and
returns the PTT to the default state.
Default: OFF.
TPM State Enables or disables the TPM. This is the normal operating state for the TPM
when you want to use its complete array of capabilities.
Default: Enabled.
Intel SGX Enables or disables the Intel Software Guard Extensions (SGX) to provide a
secured environment for running code/storing sensitive information.
Default: Software Control
SMM Security Mitigation Enables or disables additional UEFI SMM Security Mitigation protections.
Default: OFF.
NOTE: This feature may cause compatibility issues or loss of functionality
with some legacy tools and applications.
Enable Strong Passwords Enables or disables strong passwords.
Default: OFF.
Password Configuration Control the minimum and maximum number of characters that are allowed for
Admin and System passwords.
Admin Password Sets, Changes, or deletes the administrator (admin) password (sometimes
called the "setup" password).
System Password Sets, Changes, or deletes the system password.
Enable Master Password Lockout Enables or disables the master password support.
Default: OFF.
Table 8. System setup options—Secure Boot menu
Secure Boot
Enable Secure Boot Enables or disables the computer to boos using only validated boot software.
System setup 43
Table 8. System setup options—Secure Boot menu (continued)
Secure Boot
Default: OFF.
NOTE: For Secure Boot to be enabled, the computer needs to be in UEFI
boot mode and the Enable Legacy Option ROMs option needs to be turned
off.
Secure Boot Mode Selects the Secure Boot operation mode.
Default: Deployed Mode.
NOTE: Deployed Mode should be selected for normal operation of Secure
Boot.
Table 9. System setup options—Expert Key Management menu
Expert Key Management
Enable Custom Mode Enables or disables the keys in the PK, KEK, db, and dbx security key databases
to be modified.
Default: OFF.
Custom Mode Key Management Selects the custom values for expert key management.
Default: PK.
Table 10. System setup options—Performance menu
Performance
Intel Hyper-Threading Technology Enables or disables the Intel Hyper-Threading Technology to use processor
resources more efficiently.
Default: ON.
Intel SpeedStep Enables or disables the Intel SpeedStep Technology to dynamically adjust
processor voltage and core frequency, decreasing average power consumption
and heat production.
Default: ON.
Intel TurboBoost Technology Enabled or disabled the Intel TurboBoost mode of the processor. If enabled, the
Intel TurboBoost driver increases the performance of the CPU or graphics
processor.
Default: ON.
Multi-Core Support Changes the number of CPU cores available to the operating system. The
default value is set to the maximum number of cores.
Default: All Cores.
Enable C-State Control Enables or disables the CPU's ability to enter and exit low-power states.
Default: ON.
Table 11. System setup options—Power Management menu
Power Management
Wake on AC Enables the computer to turn on and go to boot when AC power is supplied to
the computer.
Default: OFF.
Wake on Dell USB-C Dock Enables connecting a Dell USB-C Dock to wake the computer from Standby.
Default: ON.
44 System setup
Table 11. System setup options—Power Management menu (continued)
Power Management
Auto on Time Enables the computer to automatically power on for defined days and times.
Default: Disabled. The system will not automatically power up.
Battery Charge Configuration Enables the computer to run on battery during power usage hours. Use the
below options to prevent AC power usage between certain times of each day.
Default: Adaptive. Battery settings are adaptively optimized based on your
typical battery usage pattern.
Enable Advanced Battery Charge
Configuration
Enables Advanced Battery Charge Configuration from the beginning of the day
to a specified work period. Advanced Battery Charged maximizes battery
health while still supporting heavy use during the work day.
Default: OFF.
Block Sleep Blocks the computer from entering Sleep (S3) mode in the operating system.
Default: OFF.
NOTE: If enabled, the computer will not go to sleep, Intel Rapid Start will
be disabled automatically, and the operating system power option will be
blank if it was set to Sleep.
Peak Shift Enables the computer to run on battery during peak power usage hours.
Default: OFF.
Wireless Radio Control Enables to sense the connection of the computer to a wired network and
subsequently disable the selected wireless radios (WLAN and/or WWAN). Upon
disconnection from the wired network, the selected wireless radios are re-
enabled.
Default: OFF.
Wake on LAN Enables or disables the computer to turn on by a special LAN signal.
Default: Disabled.
Intel Speed Shift Technology Enables or disables the Intel Speed Shift Technology support. Setting this
option to enable allows the operating system to select the appropriate
processor performance automatically.
Default: ON.
Lid Switch Enables the computer to power up from the off state whenever the lid is
opened.
Default: ON.
Table 12. System setup options—Wireless menu
Wireless
Wireless Device Enable Enable or disable internal WLAN/Bluetooth devices.
WLAN Default: ON.
Bluetooth Default: ON.
Table 13. System setup options—POST Behavior menu
POST Behavior
Numlock Enable Enables or disables Numlock when the computer boots.
Default: ON.
Enable Adapter Warnings Enables the computer to display adapter warning messages during boot.
System setup 45
Table 13. System setup options—POST Behavior menu (continued)
POST Behavior
Default: ON.
Extend BIOS POST Time Configures the BIOS POST (Power-On Self-Test) load time.
Default: 0 seconds.
Fastboot Configures the speed of the UEFI boot process.
Default: Thorough. Performs complete hardware and configuration initialization
during boot.
Fn Lock Options Enables or disables the Fn lock mode.
Default: ON.
Lock Mode Default: Lock Mode Secondary. Lock Mode Secondary = If this option is
selected, the F1-F12 keys scan the code for their secondary functions.
Full Screen Logo Enabled or disabled the computer to display full screen logo if the image match
screen resolution.
Default: OFF.
Warnings and Errors Selects an action on encountering a warning or error during boot.
Default: Prompt on Warnings and Errors. Stop, prompt, and wait for user input
when warnings or errors are detected.
NOTE: Errors deemed critical to the operation of the computer hardware
will always halt the computer.
Mouse/Touchpad Defines how the computer handles mouse and touchpad input.
Default: Touchpad and PS/2 Mouse. Leave the integrated touchapd enabled
when an external PS/2 mouse is present.
Sign of Life
Early Logo Display Display Logo Sign of Life.
Default: ON.
Early Keyboard Backlight Keyboard Backlight Sign of Life.
Default: ON.
MAC Address Pass-Through Replaces the external NIC MAC address (in a supported dock or dongle) with
the selected MAC address from the computer.
Default: System Unique MAC Address.
Table 14. System setup options—Virtualization menu
Virtualization
Intel Virtualization Technology Enables the computer to run a virtual machine monitor (VMM).
Default: ON.
VT for Direct I/O Enables the computer to perform Virtualization Technology for Direct I/O (VT-
d). VT-d is an Intel method that provides virtualization for memory map I/O.
Default: ON.
46 System setup
Table 15. System setup options—Maintenance menu
Maintenance
Asset Tag Creates a system Asset Tag that can be used by an IT administrator to
uniquely identify a particular system. Once set in BIOS, the Asset Tag cannot
be changed.
Service Tag Displays the Service Tag of the computer.
BIOS Recovery from Hard Drive Enables the computer to recover from a bad BIOS image, as long as the Boot
Block portion is intact and functioning.
Default: ON.
NOTE: BIOS recovery is designed to fix the main BIOS block and cannot
work if the Boot Block is damaged. In addition, this feature cannot work in
the event of EC corruption, ME corruption, or a hardware issue. The
recovery image must exist on an unencrypted partition on the drive.
BIOS Auto-Recovery Enables the computer to automatically recover the BIOS without user actions.
This feature requires BIOS Recovery from Hard Drive to be set to Enabled.
Default: OFF.
Start Data Wipe CAUTION: This Secure Wipe Operation deletes information in a way
that it cannot be reconstructed.
If enabled, the BIOS will queue up a data wipe cycle for storage devices that
are connected to the motherboard on the next reboot.
Default: OFF.
Allow BIOS Downgrade Controls flashing of the system firmware to previous revisions.
Default: ON.
Table 16. System setup options—System Logs menu
System Logs
Power Event Log Displays Power events.
Default: Keep.
BIOS Event Log Displays BIOS events.
Default: Keep.
Thermal Event Log Displays Thermal events.
Default: Keep.
Table 17. System setup options—SupportAssist menu
SupportAssist
Dell Auto operating system Recovery
Threshold
Controls the automatic boot flow for SupportAssist System Resolution Console
and for Dell operating system Recovery tool.
Default: 2.
SupportAssist operating system Recovery Enables or disables the boot flow for SupportAssist operating system Recovery
tool in the even of certain system errors.
Default: ON.
System setup 47
Clearing CMOS settings
About this task
CAUTION: Clearing CMOS settings will reset the BIOS settings on your computer.
Steps
1. Remove the base cover.
2. Disconnect the battery cable from the system board.
3. Wait for one minute.
4. Connect the battery cable to the system board.
5. Replace the base cover.
Clearing BIOS (System Setup) and System passwords
About this task
To clear the system or BIOS passwords, contact Dell technical support as described at www.dell.com/contactdell.
NOTE: For information on how to reset Windows or application passwords, refer to the documentation accompanying
Windows or your application.
48 System setup
Troubleshooting
Locate the Service Tag or Express Service Code of
your Dell computer
Your Dell computer is uniquely identified by a Service Tag or Express Service Code. To view relevant support resources for your
Dell computer, we recommend entering the Service Tag or Express Service Code at www.dell.com/support.
For more information on how to find the Service Tag for your computer, see Locate the Service Tag for your Dell Laptop.
Recovering the operating system
When your computer is unable to boot to the operating system even after repeated attempts, it automatically starts Dell
SupportAssist OS Recovery.
Dell SupportAssist OS Recovery is a standalone tool that is preinstalled in all Dell computers installed with Windows 10 operating
system. It consists of tools to diagnose and troubleshoot issues that may occur before your computer boots to the operating
system. It enables you to diagnose hardware issues, repair your computer, back up your files, or restore your computer to its
factory state.
You can also download it from the Dell Support website to troubleshoot and fix your computer when it fails to boot into their
primary operating system due to software or hardware failures.
For more information about the Dell SupportAssist OS Recovery, see Dell SupportAssist OS Recovery User's Guide at
www.dell.com/support.
SupportAssist | On-board Diagnostics
About this task
The SupportAssist | On-board Diagnostics performs a complete check of your hardware.
This diagnostic is the new on-board diagnostic tool and replaces the ePSA 3.0 diagnostics. It has a clean and modern user
interface, quicker tests, simplified messaging.
SupportAssist | On-board Diagnostics can be initiated by one of the following methods:
●Pressing F12 to enter one-time Boot Menu and selecting Diagnostics to initiate the diagnostics OR Fn + Power
●BIOS POST detecting a hardware failure or error and initiating the diagnostics
The SupportAssist | On-board Diagnostics is embedded with the BIOS and is launched by the BIOS internally. The embedded
system diagnostics provides a set of options for particular devices or device groups allowing you to:
●Run tests in either Quick Test Mode or Advanced Test Mode
●Run thorough tests to introduce additional test options to provide extra information about the failed device(s)
●Run tests in either Automatic Mode or Interactive Test Mode
●Run interactive tests on LCD panel and keyboard
●Display or save test results
●View status messages that indicate if the tests are completed successfully
●View error messages that indicate if problems were encountered during the test
NOTE: Some tests for specific devices require user interaction. Ensure that you are present at the computer terminal when
the diagnostic tests are performed.
For more information, see SupportAssist Pre-Boot System Performance Check.
5
Troubleshooting 49
System diagnostic lights
When static, the power and battery-charge status light indicates the power mode that your computer is in. When blinking in
different patterns, the power and battery-charge status light indicates the respective issues that your computer is
encountering.
Static power and battery-charge status light
The following table lists the status of your computer based on the power and battery-charge status light.
Table 18. Power and battery-charge status light
Power and battery-charge status light Status of computer
Solid white ●The power adapter is connected and the battery is fully
charged.
●The power adapter is connected and the battery has more
than five percent charge.
Amber The computer is running on battery and the battery has less
than five percent charge.
Off The computer is in sleep state, hibernation, or turned off.
Blinking power and battery-charge status light
The power and battery-status light blinks alternately between amber and off to indicate issues that your computer is
encountering.
For example, the power and battery-status light blinks amber two times followed by a pause, and then blinks white three times
followed by a pause. This 2,3 pattern continues until the computer is turned off indicating no memory or RAM is detected.
The following table shows the different power and battery-status light patterns and the associated issues.
Table 19. LED codes
Diagnostic light codes Problem description
2,1 Processor failure
2,2 System board: BIOS or ROM (Read-Only Memory) failure
2,3 No memory or RAM (Random-Access Memory) detected
2,4 Memory or RAM (Random-Access Memory) failure
2,5 Invalid memory installed
2,6 System-board or chipset error
2,7 Display failure
2,8 LCD power rail failure.
3,1 CMOS battery failure
3,2 PCI, video card/chip failure
3,3 Recovery image not found
3,4 Recovery image found but invalid
3,5 Power-rail failure
3,6 System BIOS Flash incomplete
3,7 Management Engine (ME) error
50 Troubleshooting
Flashing the BIOS
About this task
You may need to flash (update) the BIOS when an update is available or when you replace the system board.
Follow these steps to flash the BIOS:
Steps
1. Turn on your computer.
2. Go to www.dell.com/support.
3. Click Product support, enter the Service Tag of your computer, and then click Submit.
NOTE: If you do not have the Service Tag, use the auto-detect feature or manually browse for your computer model.
4. Click Drivers & downloads > Find it myself.
5. Select the operating system installed on your computer.
6. Scroll down the page and expand BIOS.
7. Click Download to download the latest version of the BIOS for your computer.
8. After the download is complete, navigate to the folder where you saved the BIOS update file.
9. Double-click the BIOS update file icon and follow the instructions on the screen.
Flashing BIOS (USB key)
Steps
1. Follow the procedure from step 1 to step 7 in "Flashing the BIOS" to download the latest BIOS setup program file.
2. Create a bootable USB drive. For more information see the knowledge base article SLN143196 at www.dell.com/support.
3. Copy the BIOS setup program file to the bootable USB drive.
4. Connect the bootable USB drive to the computer that needs the BIOS update.
5. Restart the computer and press F12 when the Dell logo is displayed on the screen.
6. Boot to the USB drive from the One Time Boot Menu.
7. Type the BIOS setup program filename and press Enter.
8. The BIOS Update Utility appears. Follow the instructions on the screen to complete the BIOS update.
WiFi power cycle
About this task
If your computer is unable to access the Internet due to WiFi connectivity issues, a WiFi power cycle procedure may be
performed. The following procedure provides the instructions on how to conduct a WiFi power cycle:
NOTE: Some ISPs (Internet Service Providers) provide a modem/router combo device.
Steps
1. Turn off your computer.
2. Turn off the modem.
3. Turn off the wireless router.
4. Wait for 30 seconds.
5. Turn on the wireless router.
6. Turn on the modem.
7. Turn on your computer.
Troubleshooting 51
Flea power release
About this task
Flea power is the residual static electricity that remains on the computer even after it has been powered off and the battery has
been removed. The following procedure provides the instructions on how to conduct flea power release:
Steps
1. Turn off your computer.
2. Remove the base cover.
3. Remove the battery.
4. Press and hold the power button for 15 seconds to drain the flea power.
5. Replace the battery.
6. Replace the base cover.
7. Turn on your computer.
52 Troubleshooting
Getting help and contacting Dell
Self-help resources
You can get information and help on Dell products and services using these self-help resources:
Table 20. Self-help resources
Self-help resources Resource location
Information about Dell products and services www.dell.com
My Dell app
Tips
Contact Support In Windows search, type Contact Support, and press
Enter.
Online help for operating system www.dell.com/support/windows
Access top solutions, diagnostics, drivers and downloads, and
learn more about your computer through videos, manuals and
documents.
Your Dell computer is uniquely identified by a Service Tag or
Express Service Code. To view relevant support resources for
your Dell computer, enter the Service Tag or Express Service
Code at www.dell.com/support.
For more information on how to find the Service Tag for your
computer, see Locate the Service Tag for your Dell Laptop.
Dell knowledge base articles for a variety of computer
concerns
1. Go to www.dell.com/support.
2. On the menu bar at the top of the Support page, select
Support > Knowledge Base.
3. In the Search field on the Knowledge Base page, type the
keyword, topic, or model number, and then click or tap the
search icon to view the related articles.
Contacting Dell
To contact Dell for sales, technical support, or customer service issues, see www.dell.com/contactdell.
NOTE: Availability varies by country/region and product, and some services may not be available in your country/region.
NOTE: If you do not have an active Internet connection, you can find contact information about your purchase invoice,
packing slip, bill, or Dell product catalog.
6
Getting help and contacting Dell 53