Table of Contents
- XPS 13 9310 Service Manual
- Contents
- Working inside your computer
- Removing and installing components
- Drivers and downloads
- System setup
- Troubleshooting
- Getting help and contacting Dell
DELL 9310 User Manual
Displayed below is the user manual for 9310 by DELL which is a product in the Notebooks category. This manual has pages.
Related Manuals
XPS 13 9310
Service Manual
Regulatory Model: P117G
Regulatory Type: P117G002
June 2021
Rev. A01
Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use of your product.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid
the problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
© 2020-2021 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Other trademarks may be trademarks of their respective owners.
Chapter 1: Working inside your computer...................................................................................... 5
Before working inside your computer.............................................................................................................................5
Safety instructions.............................................................................................................................................................. 5
Electrostatic discharge—ESD protection..................................................................................................................... 6
ESD field service kit ...........................................................................................................................................................6
Transporting sensitive components................................................................................................................................ 7
After working inside your computer................................................................................................................................7
Chapter 2: Removing and installing components........................................................................... 8
Recommended tools........................................................................................................................................................... 8
Screw list............................................................................................................................................................................... 8
Major components of XPS 13 9310................................................................................................................................. 9
Base cover............................................................................................................................................................................11
Removing the base cover........................................................................................................................................... 11
Installing the base cover.............................................................................................................................................14
Battery..................................................................................................................................................................................15
Lithium-ion battery precautions............................................................................................................................... 15
Removing the battery................................................................................................................................................. 16
Installing the battery....................................................................................................................................................17
Solid-state drive................................................................................................................................................................. 17
Removing the M.2 2230 solid-state drive.............................................................................................................. 17
Installing the M.2 2230 solid-state drive................................................................................................................ 18
Removing the M.2 2280 solid-state drive............................................................................................................. 20
Installing the M.2 2280 solid-state drive................................................................................................................ 21
Fans...................................................................................................................................................................................... 22
Removing the fans...................................................................................................................................................... 22
Installing the fans........................................................................................................................................................ 23
Heat sink..............................................................................................................................................................................25
Removing the heat sink............................................................................................................................................. 25
Installing the heat sink................................................................................................................................................25
Heat-sink and fan assembly............................................................................................................................................26
Removing the heat-sink and fan assembly............................................................................................................26
Installing the heat-sink and fan assembly.............................................................................................................. 27
Display assembly................................................................................................................................................................28
Removing the display assembly............................................................................................................................... 28
Installing the display assembly.................................................................................................................................. 31
System board..................................................................................................................................................................... 34
Removing the system board..................................................................................................................................... 34
Installing the system board....................................................................................................................................... 37
Status-light board............................................................................................................................................................. 40
Removing the status-light board.............................................................................................................................40
Installing the status-light board................................................................................................................................ 41
Palm-rest and keyboard assembly................................................................................................................................. 41
Removing the palm-rest and keyboard assembly.................................................................................................41
Contents
Contents 3
Installing the palm-rest and keyboard assembly.................................................................................................. 42
Chapter 3: Drivers and downloads............................................................................................... 44
Chapter 4: System setup.............................................................................................................45
Entering BIOS setup program........................................................................................................................................ 45
Navigation keys..................................................................................................................................................................45
Boot Sequence...................................................................................................................................................................45
One time boot menu......................................................................................................................................................... 46
System setup options.......................................................................................................................................................46
Clearing CMOS settings.................................................................................................................................................. 57
Clearing BIOS (System Setup) and System passwords...........................................................................................57
Chapter 5: Troubleshooting.........................................................................................................58
Handling swollen Lithium-ion batteries........................................................................................................................ 58
Recovering the operating system................................................................................................................................. 58
SupportAssist | On-board Diagnostics.........................................................................................................................59
System diagnostic lights..................................................................................................................................................59
Flea power release............................................................................................................................................................ 60
WiFi power cycle............................................................................................................................................................... 60
Chapter 6: Getting help and contacting Dell................................................................................ 62
4Contents
Working inside your computer
Before working inside your computer
About this task
NOTE: The images in this document may differ from your computer depending on the configuration you ordered.
Steps
1. Save and close all open files and exit all open applications.
2. Shut down your computer. Click Start > Power > Shut down.
NOTE: If you are using a different operating system, see the documentation of your operating system for shut-down
instructions.
3. Disconnect your computer and all attached devices from their electrical outlets.
4. Disconnect all attached network devices and peripherals, such as keyboard, mouse, and monitor from your computer.
CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the
cable from the network device.
5. Remove any media card and optical disc from your computer, if applicable.
Safety instructions
Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless
otherwise noted, each procedure included in this document assumes that you have read the safety information that shipped
with your computer.
WARNING: Before working inside your computer, read the safety information that is shipped with your
computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
WARNING: Disconnect your computer from all power sources before opening the computer cover or panels.
After you finish working inside the computer, replace all covers, panels, and screws before connecting your
computer to an electrical outlet.
CAUTION: To avoid damaging the computer, ensure that the work surface is flat, dry, and clean.
CAUTION: To avoid damaging the components and cards, handle them by their edges, and avoid touching the
pins and the contacts.
CAUTION: You should only perform troubleshooting and repairs as authorized or directed by the Dell technical
assistance team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. See the
safety instructions that is shipped with the product or at www.dell.com/regulatory_compliance.
CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal
surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal
surface to dissipate static electricity which could harm internal components.
1
Working inside your computer 5
CAUTION: When you disconnect a cable, pull it by its connector or its pull tab, not the cable itself. Some cables
have connectors with locking tabs or thumbscrews that you must disengage before disconnecting the cable.
When disconnecting cables, keep them evenly aligned to avoid bending the connector pins. When connecting
cables, ensure that the ports and the connectors are correctly oriented and aligned.
CAUTION: Press and eject any installed card from the media-card reader.
CAUTION: Exercise caution when handling Lithium-ion batteries in laptops. Swollen batteries should not be used
and should be replaced and disposed properly.
NOTE: The color of your computer and certain components may appear differently than shown in this document.
Electrostatic discharge—ESD protection
ESD is a major concern when you handle electronic components, especially sensitive components such as expansion cards,
processors, memory DIMMs, and system boards. Very slight charges can damage circuits in ways that may not be obvious, such
as intermittent problems or a shortened product life span. As the industry pushes for lower power requirements and increased
density, ESD protection is an increasing concern.
Due to the increased density of semiconductors used in recent Dell products, the sensitivity to static damage is now higher than
in previous Dell products. For this reason, some previously approved methods of handling parts are no longer applicable.
Two recognized types of ESD damage are catastrophic and intermittent failures.
●Catastrophic – Catastrophic failures represent approximately 20 percent of ESD-related failures. The damage causes
an immediate and complete loss of device functionality. An example of catastrophic failure is a memory DIMM that has
received a static shock and immediately generates a "No POST/No Video" symptom with a beep code emitted for missing or
nonfunctional memory.
●Intermittent – Intermittent failures represent approximately 80 percent of ESD-related failures. The high rate of
intermittent failures means that most of the time when damage occurs, it is not immediately recognizable. The DIMM
receives a static shock, but the tracing is merely weakened and does not immediately produce outward symptoms related to
the damage. The weakened trace may take weeks or months to melt, and in the meantime may cause degradation of memory
integrity, intermittent memory errors, etc.
The more difficult type of damage to recognize and troubleshoot is the intermittent (also called latent or "walking wounded")
failure.
Perform the following steps to prevent ESD damage:
●Use a wired ESD wrist strap that is properly grounded. The use of wireless anti-static straps is no longer allowed; they do not
provide adequate protection. Touching the chassis before handling parts does not ensure adequate ESD protection on parts
with increased sensitivity to ESD damage.
●Handle all static-sensitive components in a static-safe area. If possible, use anti-static floor pads and workbench pads.
●When unpacking a static-sensitive component from its shipping carton, do not remove the component from the anti-static
packing material until you are ready to install the component. Before unwrapping the anti-static packaging, ensure that you
discharge static electricity from your body.
●Before transporting a static-sensitive component, place it in an anti-static container or packaging.
ESD field service kit
The unmonitored Field Service kit is the most commonly used service kit. Each Field Service kit includes three main components:
anti-static mat, wrist strap, and bonding wire.
Components of an ESD field service kit
The components of an ESD field service kit are:
●Anti-Static Mat – The anti-static mat is dissipative and parts can be placed on it during service procedures. When using an
anti-static mat, your wrist strap should be snug and the bonding wire should be connected to the mat and to any bare metal
on the system being worked on. Once deployed properly, service parts can be removed from the ESD bag and placed directly
on the mat. ESD-sensitive items are safe in your hand, on the ESD mat, in the system, or inside a bag.
6Working inside your computer
●Wrist Strap and Bonding Wire – The wrist strap and bonding wire can be either directly connected between your wrist
and bare metal on the hardware if the ESD mat is not required, or connected to the anti-static mat to protect hardware that
is temporarily placed on the mat. The physical connection of the wrist strap and bonding wire between your skin, the ESD
mat, and the hardware is known as bonding. Use only Field Service kits with a wrist strap, mat, and bonding wire. Never
use wireless wrist straps. Always be aware that the internal wires of a wrist strap are prone to damage from normal wear
and tear, and must be checked regularly with a wrist strap tester in order to avoid accidental ESD hardware damage. It is
recommended to test the wrist strap and bonding wire at least once per week.
●ESD Wrist Strap Tester – The wires inside of an ESD strap are prone to damage over time. When using an unmonitored
kit, it is a best practice to regularly test the strap prior to each service call, and at a minimum, test once per week. A
wrist strap tester is the best method for doing this test. If you do not have your own wrist strap tester, check with your
regional office to find out if they have one. To perform the test, plug the wrist-strap's bonding-wire into the tester while it is
strapped to your wrist and push the button to test. A green LED is lit if the test is successful; a red LED is lit and an alarm
sounds if the test fails.
●Insulator Elements – It is critical to keep ESD sensitive devices, such as plastic heat sink casings, away from internal parts
that are insulators and often highly charged.
●Working Environment – Before deploying the ESD Field Service kit, assess the situation at the customer location. For
example, deploying the kit for a server environment is different than for a desktop or portable environment. Servers are
typically installed in a rack within a data center; desktops or portables are typically placed on office desks or cubicles. Always
look for a large open flat work area that is free of clutter and large enough to deploy the ESD kit with additional space to
accommodate the type of system that is being repaired. The workspace should also be free of insulators that can cause an
ESD event. On the work area, insulators such as Styrofoam and other plastics should always be moved at least 12 inches or
30 centimeters away from sensitive parts before physically handling any hardware components
●ESD Packaging – All ESD-sensitive devices must be shipped and received in static-safe packaging. Metal, static-shielded
bags are preferred. However, you should always return the damaged part using the same ESD bag and packaging that the
new part arrived in. The ESD bag should be folded over and taped shut and all the same foam packing material should be
used in the original box that the new part arrived in. ESD-sensitive devices should be removed from packaging only at an
ESD-protected work surface, and parts should never be placed on top of the ESD bag because only the inside of the bag is
shielded. Always place parts in your hand, on the ESD mat, in the system, or inside an anti-static bag.
●Transporting Sensitive Components – When transporting ESD sensitive components such as replacement parts or parts
to be returned to Dell, it is critical to place these parts in anti-static bags for safe transport.
ESD protection summary
It is recommended that all field service technicians use the traditional wired ESD grounding wrist strap and protective anti-static
mat at all times when servicing Dell products. In addition, it is critical that technicians keep sensitive parts separate from all
insulator parts while performing service and that they use anti-static bags for transporting sensitive components.
Transporting sensitive components
When transporting ESD sensitive components such as replacement parts or parts to be returned to Dell, it is critical to place
these parts in anti-static bags for safe transport.
After working inside your computer
About this task
CAUTION: Leaving stray or loose screws inside your computer may severely damage your computer.
Steps
1. Replace all screws and ensure that no stray screws remain inside your computer.
2. Connect any external devices, peripherals, or cables you removed before working on your computer.
3. Replace any media cards, discs, or any other parts that you removed before working on your computer.
4. Connect your computer and all attached devices to their electrical outlets.
5. Turn on your computer.
Working inside your computer 7
Removing and installing components
NOTE: The images in this document may differ from your computer depending on the configuration you ordered.
Recommended tools
The procedures in this document may require the following tools:
●Phillips screwdriver #0
●Phillips screwdriver #1
●Torx #5 (T5) screwdriver
●Plastic scribe
Screw list
NOTE: When removing screws from a component, it is recommended to note the screw type, the quantity of screws, and
then place them in a screw storage box. This is to ensure that the correct number of screws and correct screw type is
restored when the component is replaced.
NOTE: Some computers have magnetic surfaces. Ensure that the screws are not left attached to such surfaces when
replacing a component.
NOTE: Screw color may vary with the configuration ordered.
Table 1. Screw list
Component Secured to Screw type Quantity Screw image
Base cover Palm-rest and keyboard
assembly
M2x3, Torx 5 8
Battery Palm-rest and keyboard
assembly
M1.6x2.5 5
Solid-state drive shield System board M2x3 1
Fans (in computers
shipped with
computers shipped
with 11th Generation
Intel Core i3-1115G4
processor)
System board M1.6x2.5 4
Heat sink (in
computers shipped
with computers
shipped with 11th
Generation Intel Core
i3-1115G4 processor)
System board M2x3 (captive) 4
2
8 Removing and installing components
Table 1. Screw list (continued)
Component Secured to Screw type Quantity Screw image
Heat-sink and
fan assembly (in
computers shipped
with computers
shipped with 11th
Generation Intel Core
i5-1135G7 processor
or 11th Generation
Intel Core i7-1165G7
processor)
System board M2x3 (captive) 4
Heat-sink and
fan assembly (in
computers shipped
with computers
shipped with 11th
Generation Intel Core
i5-1135G7 processor
or 11th Generation
Intel Core i7-1165G7
processor)
System board M1.6x2.5 4
Display-assembly
cable bracket
System board M1.6x2 (captive) 3
Display-assembly
cable holder
System board M1.2x2 3
Display-assembly
hinges
Palm-rest and keyboard
assembly
M2.5x4.5 6
Wireless-card bracket System board M1.6x2.3 (captive) 1
System board Palm-rest and keyboard
assembly
M1.6x1.5 4
System board Palm-rest and keyboard
assembly
M1.2x2 3
System board Palm-rest and keyboard
assembly
M1.4x4 4
Major components of XPS 13 9310
The following image shows the major components of XPS 13 9310.
Removing and installing components 9
1. Base cover
2. Battery
3. Left fan (in computers shipped with 11th Generation Intel Core i3-1115G4 processor)
NOTE: The left fan is part of the heat-sink and fan assembly in computers shipped with 11th Generation Intel Core
i5-1135G7 or 11th Generation Intel Core i7-1165G7 processor.
4. Heat sink (in computers shipped with 11th Generation Intel Core i3-1115G4 processor)
NOTE: The heat sink and the fans are components of the heat-sink and fan assembly in computers shipped with 11th
Generation Intel Core i5-1135G7 or 11th Generation Intel Core i7-1165G7 processor.
5. Left antenna
6. System board
7. Left speaker
8. Palm-rest and keyboard assembly
9. Display assembly
10. Right speaker
11. Display-cable bracket
12. Right antenna
13. Right fan (in computers shipped with 11th Generation Intel Core i3-1115G4 processor)
NOTE: The right fan is part of the heat-sink and fan assembly in computers shipped with 11th Generation Intel Core
i5-1135G7 or 11th Generation Intel Core i7-1165G7 processor.
14. Solid-state drive shield
10 Removing and installing components
15. Solid-state drive
NOTE: Dell provides a list of components and their part numbers for the original system configuration purchased. These
parts are available according to warranty coverages purchased by the customer. Contact your Dell sales representative for
purchase options.
Base cover
Removing the base cover
Prerequisites
1. Follow the procedure in Before working inside your computer.
About this task
The following images indicate the location of the base cover and provide a visual representation of the removal procedure.
Removing and installing components 11
12 Removing and installing components
Steps
1. Remove the eight screws (M2x3, Torx 5) that secure the base cover to the palm-rest and keyboard assembly.
2. Starting from the bottom-left corner, use a plastic scribe to pry the base cover in the direction of the arrows to release the
base cover from the palm-rest and keyboard assembly.
CAUTION: Do not pull on or pry the base cover from the side where the hinges are; doing so may damage the
base cover.
3. Hold both sides of the base cover and rotate the base cover from bottom to top to remove it from the palm-rest and
keyboard assembly.
NOTE: The pins at the bottom of the base cover for grounding the antennas and the audio board are fragile. Place the
base cover on a clean surface to avoid damage to the pins.
NOTE: The following steps are applicable only if you want to further remove any other component from your computer.
4. Peel the tape that secures the battery cable to the battery.
5. Using the pull tab, disconnect the battery cable from the system board.
6. Turn your computer over and press the power button for 15 seconds to drain the flea power.
Removing and installing components 13
Installing the base cover
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the base cover and provide a visual representation of the installation procedure.
14 Removing and installing components
Steps
1. Connect the battery cable to the system board.
2. Pivot the base cover against the side of the palm-rest and keyboard assembly where the hinges are and snap the base cover
into place.
NOTE: Ensure that the screw holes on the base cover are aligned with the screw holes on the palm-rest and keyboard
assembly.
3. Replace the eight screws (M2x3, Torx 5) that secure the base cover to the palm-rest and keyboard assembly.
Next steps
1. Follow the procedure in After working inside your computer.
Battery
Lithium-ion battery precautions
CAUTION:
●Exercise caution when handling Lithium-ion batteries.
●Discharge the battery completely before removing it. Disconnect the AC power adapter from the system and
operate the computer solely on battery power—the battery is fully discharged when the computer no longer
turns on when the power button is pressed.
●Do not crush, drop, mutilate, or penetrate the battery with foreign objects.
●Do not expose the battery to high temperatures, or disassemble battery packs and cells.
Removing and installing components 15
●Do not apply pressure to the surface of the battery.
●Do not bend the battery.
●Do not use tools of any kind to pry on or against the battery.
●Ensure any screws during the servicing of this product are not lost or misplaced, to prevent accidental
puncture or damage to the battery and other system components.
●If the battery gets stuck inside your computer as a result of swelling, do not try to release it as puncturing,
bending, or crushing a lithium-ion battery can be dangerous. In such an instance, contact Dell technical
support for assistance. See www.dell.com/contactdell.
●Always purchase genuine batteries from www.dell.com or authorized Dell partners and resellers.
●Swollen batteries should not be used and should be replaced and disposed properly. For guidelines on how to
handle and replace swollen Lithium-ion batteries, see Handling swollen Lithium-ion batteries.
Removing the battery
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
About this task
The following image indicates the location of the battery and provides a visual representation of the removal procedure.
Steps
1. Peel off the tape and disconnect the battery cable from the system board, if the battery cable is still connected to the
system board.
2. Remove the five screws (M1.6x2.5) that secure the battery to the palm-rest and keyboard assembly.
3. Lift the battery off the palm-rest and keyboard assembly.
16 Removing and installing components
Installing the battery
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the battery and provides a visual representation of the installation procedure.
Steps
1. Align the screw holes on the battery with the screw holes on the palm-rest and keyboard assembly.
2. Replace the five screws (M1.6x2.5) that secure the battery to the palm-rest and keyboard assembly.
3. Connect the battery cable to the system board.
Next steps
1. Install the base cover.
2. Follow the procedure in After working inside your computer.
Solid-state drive
Removing the M.2 2230 solid-state drive
Prerequisites
1. Follow the procedure in Before working inside your computer.
CAUTION: Solid-state drives are fragile. Exercise care when handling the solid-state drive.
CAUTION: To avoid data loss, do not remove the solid-state drive while the computer is in sleep or on state.
2. Remove the base cover.
Removing and installing components 17
About this task
NOTE: Depending on the configuration ordered, your computer may support an M.2 2230 solid-state drive or an M.2 2280
solid-state drive.
NOTE: This procedure applies only to computers shipped with an M.2 2230 solid-state drive.
The following image indicates the location of the M.2 2230 solid-state drive and provides a visual representation of the removal
procedure.
Steps
1. Remove the antenna cable from the routing guides along the edge of the solid-state drive shield.
2. Remove the screw (M2x3) that secures the M.2 2230 solid-state drive shield to the system board.
3. Slide and lift the M.2 2230 solid-state drive off the solid-state drive slot on the system board.
Installing the M.2 2230 solid-state drive
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
CAUTION: Solid-state drives are fragile. Exercise care when handling the solid-state drive.
CAUTION: To avoid data loss, do not remove the solid-state drive while the computer is in sleep or on state.
18 Removing and installing components
About this task
NOTE: Depending on the configuration ordered, your computer may support an M.2 2230 solid-state drive or an M.2 2280
solid-state drive.
NOTE: This procedure applies only if you are installing an M.2 2230 solid-state drive.
The following image indicates the location of the M.2 2230 solid-state drive and provides a visual representation of the
installation procedure.
Steps
1. Align the notch on the M.2 2230 solid-state drive with the tab on solid-state drive slot on the system board.
2. Slide the M.2 2230 solid-state drive into solid-state drive slot on the system board.
3. Insert the notch on the solid-state drive shield into a slot on the peg on the system board.
4. Replace the screw (M2x3) that secures the M.2 2230 solid-state drive shield to the system board.
5. Route the antenna cable through the routing guides along the solid-state drive shield.
Next steps
1. Install the base cover.
2. Follow the procedure in After working inside your computer.
Removing and installing components 19
Removing the M.2 2280 solid-state drive
Prerequisites
1. Follow the procedure in Before working inside your computer.
CAUTION: Solid-state drives are fragile. Exercise care when handling the solid-state drive.
CAUTION: To avoid data loss, do not remove the solid-state drive while the computer is in sleep or on state.
2. Remove the base cover.
About this task
NOTE: Depending on the configuration ordered, your computer may support an M.2 2280 solid-state drive or an M.2 2280
solid-state drive.
NOTE: This procedure applies only to computers shipped with an M.2 2280 solid-state drive.
The following image indicates the location of the M.2 2280 solid-state drive and provides a visual representation of the removal
procedure.
Steps
1. Remove the antenna cable from the routing guides along the edge of the solid-state drive shield.
2. Remove the screw (M2x3) that secures the M.2 2280 solid-state drive shield to the system board.
3. Slide and lift the M.2 2280 solid-state drive off the solid-state drive slot on the system board.
20 Removing and installing components
Installing the M.2 2280 solid-state drive
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
CAUTION: Solid-state drives are fragile. Exercise care when handling the solid-state drive.
CAUTION: To avoid data loss, do not remove the solid-state drive while the computer is in sleep or on state.
About this task
NOTE: Depending on the configuration ordered, your computer may support an M.2 2280 solid-state drive or an M.2 2280
solid-state drive.
NOTE: This procedure applies only if you are installing an M.2 2280 solid-state drive.
The following image indicates the location of the M.2 2280 solid-state drive and provides a visual representation of the
installation procedure.
Steps
1. Align the notch on the M.2 2280 solid-state drive with the tab on solid-state drive slot on the system board.
2. Slide the M.2 2280 solid-state drive into solid-state drive slot on the system board.
3. Insert the notch on the solid-state drive shield into a slot on the peg on the system board.
Removing and installing components 21
4. Replace the screw (M2x3) that secures the M.2 2280 solid-state drive shield to the system board.
5. Route the antenna cable through the routing guides along the solid-state drive shield.
Next steps
1. Install the base cover.
2. Follow the procedure in After working inside your computer.
Fans
Removing the fans
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
About this task
NOTE: This procedure applies to computers shipped with 11th Generation Intel Core i3-1115G4 processor.
The following images indicate the location of the fans and provide a visual representation of the removal procedure.
22 Removing and installing components
Steps
1. Peel the tape that secures the fan A cable to the system board.
2. Disconnect the fan A cable from the system board.
3. Remove the two screws (M1.6x2.5) that secure fan A to the system board.
4. Lift fan A off the system board.
5. Peel the tape that secures the fan B cable to the system board.
6. Disconnect the fan B cable from the system board.
7. Remove the two screws (M1.6x2.5) that secure fan B to the system board.
8. Lift fan B off the system board.
Installing the fans
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
NOTE: This procedure applies to computers shipped with 11th Generation Intel Core i3-1115G4 processor.
The following images indicate the location of the fans and provide a visual representation of the installation procedure.
Removing and installing components 23
Steps
1. Align the screw holes on fan B with the screw holes on the system board.
2. Replace the two screws (M1.6x2.5) that secure fan B to the system board.
3. Connect the fan B cable to the system board.
4. Adhere the tape that secures the fan B cable to the system board.
5. Align the screw holes on fan A with the screw holes on the system board.
6. Replace the two screws (M1.6x2.5) that secure fan A to the system board.
7. Connect the fan A cable to the system board.
8. Adhere the tape that secures the fan A cable to the system board.
24 Removing and installing components
Next steps
1. Install the base cover.
2. Follow the procedure in After working inside your computer.
Heat sink
Removing the heat sink
Prerequisites
1. Follow the procedure in Before working inside your computer.
CAUTION: For maximum cooling of the processor, do not touch the heat transfer areas on the heat sink. The
oils in your skin can reduce the heat transfer capability of the thermal grease.
NOTE: The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to cool before you
touch it.
2. Remove the base cover.
About this task
NOTE: This procedure applies to computers shipped with 11th Generation Intel Core i3-1115G4 processor. The heat sink and
the fans are separate units.
The following image indicates the location of the heat sink and provides a visual representation of the removal procedure.
Steps
1. In reverse sequential order (as indicated on the heat sink), loosen the four captive screws (M2x3) that secure the heat sink
to the system board.
2. Lift the heat sink off the system board.
Installing the heat sink
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
Removing and installing components 25
NOTE: This procedure applies to computers shipped with 11th Generation Intel Core i3-1115G4 processor. The heat sink and
the fans are separate units.
CAUTION: Incorrect alignment of the heat sink can damage the system board and processor.
NOTE: If either the system board or the heat sink is replaced, use the thermal pad/paste provided in the kit to ensure that
thermal conductivity is achieved.
About this task
The following image indicates the location of the heat sink and provides a visual representation of the installation procedure.
Steps
1. Align the screw holes on the heat sink with the screw holes on the system board.
2. In sequential order (as indicated on the heat sink), tighten the four captive screws (M2x3) that secure the heat sink to the
system board.
Next steps
1. Install the base cover.
2. Follow the procedure in After working inside your computer.
Heat-sink and fan assembly
Removing the heat-sink and fan assembly
Prerequisites
1. Follow the procedure in Before working inside your computer.
CAUTION: For maximum cooling of the processor, do not touch the heat transfer areas on the heat-sink and
fan assembly. The oils in your skin can reduce the heat transfer capability of the thermal grease.
NOTE: The heat-sink and fan assembly may become hot during normal operation. Allow sufficient time for the heat-sink
and fan assembly to cool before you touch it.
2. Remove the base cover.
26 Removing and installing components
About this task
NOTE: This procedure applies to computers shipped with 11th Generation Intel Core i5-1135G7 processor or 11th Generation
Intel Core i7-1165G7 processor. The heat sink and the fans are combined in a heat-sink and fan assembly.
The following image indicates the location of the heat-sink and fan assembly and provides a visual representation of the removal
procedure.
Steps
1. In reverse sequential order (as indicated on the heat-sink and fan assembly), loosen the four captive screws (M2x3) that
secure the heat-sink and fan assembly to the system board.
2. Peel the tapes that secure the fan cables to the system board.
3. Disconnect the fan cables from the system board.
4. Remove the four screws (M1.6x2.5) that secure the fans to the system board.
5. Lift the heat-sink and fan assembly off the system board.
Installing the heat-sink and fan assembly
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
NOTE: This procedure applies to computers shipped with 11th Generation Intel Core i5-1135G7 processor or 11th Generation
Intel Core i7-1165G7 processor. The heat sink and the fans are combined in a heat-sink and fan assembly.
CAUTION: Incorrect alignment of the heat-sink and fan assembly can damage the system board and processor.
NOTE: If either the system board or the heat-sink and fan assembly is replaced, use the thermal pad/paste provided in the
kit to ensure that thermal conductivity is achieved.
About this task
The following image indicates the location of the heat-sink and fan assembly and provides a visual representation of the
installation procedure.
Removing and installing components 27
Steps
1. Align the screw holes on the heat-sink and fan assembly with the screw holes on the system board.
2. In sequential order (as indicated on the heat-sink and fan assembly), tighten the four captive screws (M2x3) that secure the
heat-sink and fan assembly to the system board.
3. Replace the four screws (M1.6x2.5) that secure the fans to the system board.
4. Connect the fan cables to the system board.
5. Adhere the tape that secures the fan cables to the system board.
Next steps
1. Install the base cover.
2. Follow the procedure in After working inside your computer.
Display assembly
Removing the display assembly
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
About this task
The following images indicate the location of the display assembly and provide a visual representation of the removal procedure.
28 Removing and installing components
Removing and installing components 29
Steps
1. Loosen the three captive screws (M1.6x2) that secure the display-assembly cable bracket to the system board.
2. Lift the display-assembly cable bracket off the system board.
3. Disconnect the camera cable (optional) and the display cable from the system board.
NOTE: There is no camera cable if the camera is not included in the configuration ordered.
4. Remove the three screws (M1.2x2) that secure the display-assembly cable holder to the palm-rest and keyboard assembly.
5. Remove the three screws (M2.5x4.5) that secure the left hinge to the system board and the palm-rest and keyboard
assembly.
6. Remove the three screws (M2.5x4.5) that secure the right hinge to the system board and the palm-rest and keyboard
assembly.
7. Slide the palm-rest and keyboard assembly from the display assembly.
8. After performing all the above steps, you are left with display assembly.
30 Removing and installing components
Installing the display assembly
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the display assembly and provide a visual representation of the installation
procedure.
Removing and installing components 31
32 Removing and installing components
Steps
1. Slide the palm-rest and keyboard assembly under the display-assembly hinges.
2. Align the screw holes on the palm-rest assembly with the screw holes on the display hinges.
3. Replace the three screws (M2.5x4.5) that secure the left hinge to the system board and the palm-rest and keyboard
assembly.
4. Replace the three screws (M2.5x4.5) that secure the right hinge to the system board and the palm-rest and keyboard
assembly.
5. Align the screw holes on the display-assembly cable holder with the screw holes on the palm-rest and keyboard assembly.
6. Replace the three screws (M1.2x2) that secure the display-assembly cable holder to the palm-rest and keyboard assembly.
NOTE: Apply gentle torque when tightening the three screws (M1.2x2) to avoid damaging the screw threads.
7. Connect the camera cable (optional) and the display cable to the system board.
NOTE: There is no camera cable if the camera is not included in the configuration ordered.
8. Align the screw holes on the display-assembly cable bracket with the screw holes on the system board and tighten the three
captive screws (M1.6x2).
Next steps
1. Install the base cover.
Removing and installing components 33
2. Follow the procedure in After working inside your computer.
System board
Removing the system board
Prerequisites
1. Follow the procedure in Before working inside your computer.
NOTE: Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup
program after you replace the system board.
NOTE: Replacing the system board removes any changes you have made to the BIOS using the BIOS setup program.
You must make the appropriate changes again after you replace the system board.
NOTE: Before disconnecting the cables from the system board, note the location of the connectors so that you can
reconnect the cables correctly after you replace the system board.
2. Remove the base cover.
3. Remove the battery.
4. Remove the fans (for computers shipped with 11th Generation Intel Core i3-1115G4 processor).
5. Remove the heat sink (for computers shipped with 11th Generation Intel Core i3-1115G4 processor).
NOTE: The system board can be removed or installed together with the heat sink attached. This simplifies the
procedure and avoids breaking the thermal bond between the system board and the heat sink.
6. Remove the heat-sink and fan assembly (for computers shipped with 11th Generation Intel Core i5-1135G7 processor or 11th
Generation Intel Core i7-1165G7 processor).
7. Remove the M.2 2230 solid-state drive or the M.2 2280 solid-state drive.
8. Remove the display assembly.
About this task
The following image indicates the connectors on your system board.
Figure 1. System-board connectors
1. Power-button and fingerprint reader cable 2. Touchpad cable
3. Right speaker cable 4. Keyboard cable
5. Left speaker cable
The following images indicate the location of the system board and provide a visual representation of the removal procedure.
34 Removing and installing components
Removing and installing components 35
Steps
1. Loosen the captive screw (M1.6x2.3) that secures the wireless-card bracket to the system board.
2. Lift the wireless-card bracket off the system board.
3. Using a plastic scribe, disconnect the antenna cables from the wireless card.
4. Note the routing of the left and the right antenna cables.
5. Starting from the wireless card, remove each antenna cable from the routing guides, toward their respective antennas.
6. Open the latch, and disconnect the power-button and fingerprint reader cable from the system board.
7. Disconnect the right speaker cable from the system board.
8. Open the latch, and disconnect the keyboard cable from the system board.
9. Open the latch, and disconnect the touchpad cable from the system board.
10. Disconnect the left speaker cable from the system board.
11. Remove the four screws (M1.6x1.5) that secure the system board to the palm-rest and keyboard assembly.
12. Remove the three screws (M1.2x2) that secure the system board to the palm-rest and keyboard assembly.
13. Remove the four screws (M1.4x4) that secure the system board to the palm-rest and keyboard assembly.
14. Lift the system board off the palm-rest and keyboard assembly.
36 Removing and installing components
Installing the system board
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
NOTE: Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup
program after you replace the system board.
NOTE: Replacing the system board removes any changes you have made to the BIOS using the BIOS setup program. You
must make the appropriate changes again after you replace the system board.
About this task
The following image indicates the connectors on your system board.
Figure 2. System-board connectors
1. Power-button and fingerprint reader cable 2. Touchpad cable
3. Right speaker cable 4. Keyboard cable
5. Left speaker cable
The following images indicate the location of the system board and provide a visual representation of the installation procedure.
Removing and installing components 37
38 Removing and installing components
Steps
1. Align the screw holes on the system board with the screw holes on the palm-rest and keyboard assembly.
2. Replace the four screws (M1.6x1.5) that secure the system board to the palm-rest and keyboard assembly.
3. Replace the three screws (M1.2x2) that secure the system board to the palm-rest and keyboard assembly.
4. Replace the four screws (M1.4x4) that secure the system board to the palm-rest and keyboard assembly.
5. Connect the power-button and fingerprint reader cable to the system board and close the latch to secure the cable.
6. Connect the right speaker cable to the system board.
7. Connect the keyboard cable to the system board and close the latch to secure the cable.
8. Connect the touchpad cable to the system board and close the latch to secure the cable.
9. Connect the left speaker cable to the system board.
10. Route the left and right antenna cables through the routing guides on the palm-rest and keyboard assembly toward the
wireless card.
11. Connect the antenna cables to the wireless card.
12. Align the screw hole on the wireless-card bracket with the screw hole on the system board.
NOTE: Ensure that tab on the wireless-card bracket is inserted into the slot in the system board.
13. Tighten the captive screw (M1.6x2.3) that secures the wireless-card bracket to the system board.
Removing and installing components 39
Next steps
1. Install the display assembly.
2. Install the M.2 2230 solid-state drive or the M.2 2280 solid-state drive.
3. Install the heat sink (for computers shipped with 11th Generation Intel Core i3-1115G4 processor).
NOTE: The system board can be removed or installed together with the heat sink attached. This simplifies the
procedure and avoids breaking the thermal bond between the system board and the heat sink.
4. Install the fans (for computers shipped with 11th Generation Intel Core i3-1115G4 processor).
5. Install the heat-sink and fan assembly (for computers shipped with 11th Generation Intel Core i5-1135G7 processor or 11th
Generation Intel Core i7-1165G7 processor).
6. Install the battery.
7. Install the base cover.
8. Follow the procedure in After working inside your computer.
Status-light board
Removing the status-light board
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
3. Remove the battery.
About this task
The following image indicates the status-light board and provides a visual representation of the removal procedure.
Steps
1. Lift the latch and disconnect the status-light board cable from the keyboard-control daughterboard on the palm-rest and
keyboard assembly.
2. Using a plastic scribe, pry the status-light board by its right side.
3. Carefully peel the status-light board from the palm-rest and keyboard assembly.
40 Removing and installing components
Installing the status-light board
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the status-light board and provides a visual representation of the installation procedure.
Steps
1. Place the status-light board into its slot on the palm-rest and keyboard assembly.
NOTE: Ensure that the right side of the status-light board is aligned with the peg on the palm-rest and keyboard
assembly.
2. Connect the status-light board cable to the keyboard-control daughterboard on the palm-rest and keyboard assembly and
close the latch to secure the cable.
Next steps
1. Install the battery.
2. Install the base cover.
3. Follow the procedure in After working inside your computer.
Palm-rest and keyboard assembly
Removing the palm-rest and keyboard assembly
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
3. Remove the battery.
4. Remove the display assembly.
5. Remove the system board.
Removing and installing components 41
NOTE: The system board can be removed with the heat sink or the heat-sink and fan assembly attached.
6. Remove the status-light board.
About this task
The following image indicates the palm-rest and keyboard assembly and provides a visual representation of the removal
procedure.
After performing the steps in the pre-requisites, you are left with the palm-rest and keyboard assembly.
Installing the palm-rest and keyboard assembly
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the palm-rest and keyboard assembly and provides a visual representation of the installation
procedure.
42 Removing and installing components
Steps
Place the palm-rest and keyboard assembly on a flat surface.
Next steps
1. Install the status-light board.
2. Install the system board.
3. Install the display assembly.
4. Install the battery.
5. Install the base cover.
NOTE: The system board can be installed with the heat sink or the heat-sink and fan assembly attached.
6. Follow the procedure in After working inside your computer.
Removing and installing components 43
System setup
CAUTION: Unless you are an expert computer user, do not change the settings in the BIOS Setup program.
Certain changes can make your computer work incorrectly.
NOTE: Depending on the computer and its installed devices, the items listed in this section may or may not be displayed.
NOTE: Before you change BIOS Setup program, it is recommended that you write down the BIOS Setup program screen
information for future reference.
Use the BIOS Setup program for the following purposes:
●Get information about the hardware installed in your computer, such as the amount of RAM and the size of the hard drive.
●Change the system configuration information.
●Set or change a user-selectable option, such as the user password, type of hard drive installed, and enabling or disabling
base devices.
Entering BIOS setup program
About this task
Turn on (or restart) your computer and press F2 immediately.
Navigation keys
NOTE: For most of the System Setup options, changes that you make are recorded but do not take effect until you restart
the system.
Table 2. Navigation keys
Keys Navigation
Up arrow Moves to the previous field.
Down arrow Moves to the next field.
Enter Selects a value in the selected field (if applicable) or follow
the link in the field.
Spacebar Expands or collapses a drop-down list, if applicable.
Tab Moves to the next focus area.
NOTE: For the standard graphics browser only.
Esc Moves to the previous page until you view the main screen.
Pressing Esc in the main screen displays a message that
prompts you to save any unsaved changes and restarts the
system.
Boot Sequence
Boot Sequence allows you to bypass the System Setup–defined boot device order and boot directly to a specific device (for
example: optical drive or hard drive). During the Power-on Self Test (POST), when the Dell logo appears, you can:
●Access System Setup by pressing F2 key
4
System setup 45
●Bring up the one-time boot menu by pressing F12 key
The one-time boot menu displays the devices that you can boot from including the diagnostic option. The boot menu options
are:
●Removable Drive (if available)
●STXXXX Drive (if available)
NOTE: XXX denotes the SATA drive number.
●Optical Drive (if available)
●SATA Hard Drive (if available)
●Diagnostics
The boot sequence screen also displays the option to access the System Setup screen.
One time boot menu
To enter one time boot menu, turn on your computer, and then press F12 immediately.
NOTE: It is recommended to shutdown the computer if it is on.
The one-time boot menu displays the devices that you can boot from including the diagnostic option. The boot menu options
are:
●Removable Drive (if available)
●STXXXX Drive (if available)
NOTE: XXX denotes the SATA drive number.
●Optical Drive (if available)
●SATA Hard Drive (if available)
●Diagnostics
The boot sequence screen also displays the option to access the System Setup screen.
System setup options
NOTE: Depending on this computer and its installed devices, the items that are listed in this section may or may not be
displayed.
Table 3. System setup options—Overview menu
Overview
XPS 13 9310
BIOS Version Displays the BIOS version number.
Service Tag Displays the Service Tag of the computer.
Asset Tag Displays the Asset Tag of the computer.
Manufacture Date Displays the manufacture date of the computer.
Ownership Date Displays the ownership date of the computer.
Express Service Code Displays the express service code of the computer.
Ownership Tag Displays the ownership tag of the computer.
Signed Firmware Update Displays whether the signed firmware update is enabled.
Default: Enabled
BATTERY
Primary Displays the primary battery.
Battery Level Displays the battery level.
46 System setup
Table 3. System setup options—Overview menu (continued)
Overview
Battery State Displays the battery state.
Health Displays the battery health.
AC Adapter Displays whether an AC adapter is connected. If connected, the AC adapter type.
PROCESSOR
Processor Type Displays the processor type.
Maximum Clock Speed Displays the maximum processor clock speed.
Minimum Clock Speed Displays the minimum processor clock speed.
Current Clock Speed Displays the current processor clock speed.
Core Count Displays the number of cores on the processor.
Processor ID Displays the processor identification code.
Processor L2 Cache Displays the processor L2 Cache size.
Processor L3 Cache Displays the processor L3 Cache size.
Microcode Version Displays the microcode version.
Intel Hyper-Threading Capable Displays whether the processor is Hyper-Threading (HT) capable.
64-Bit Technology Displays whether 64-bit technology is used.
MEMORY
Memory Installed Displays the total computer memory installed.
Memory Available Displays the total computer memory available.
Memory Speed Displays the memory speed.
Memory Channel Mode Displays single or dual channel mode.
Memory Technology Displays the technology that is used for the memory.
DEVICES
Panel Type Displays the Panel Type of the computer.
Video Controller Displays the integrate graphics information of the computer.
Video Memory Displays the video memory information of the computer.
Wi-Fi Device Displays the Wi-Fi device installed in the computer.
Native Resolution Displays the native resolution of the computer.
Video BIOS Version Displays the video BIOS version of the computer.
Audio Controller Displays the audio controller information of the computer.
Bluetooth Device Displays whether a Bluetooth device is installed in the computer.
Pass Through MAC Address Displays the MAC address of the video pass-through.
Table 4. System setup options—Boot Configuration menu
Boot Configuration
Boot Mode: UEFI only Displays the boot mode of this computer.
Boot Sequence Displays the boot sequence.
Secure Digital (SD) Card Boot Enables or disables boot from Secure Digital card.
By default, Enable Secure Digital (SD) Card Boot is selected.
System setup 47
Table 4. System setup options—Boot Configuration menu (continued)
Boot Configuration
Secure Boot
Enable Secure Boot Enables or disables the computer to boot using only validated boot software.
Default: OFF
NOTE: For Secure Boot to be enabled, the computer needs to be in UEFI
boot mode and the Enable Legacy Option ROMs option needs to be turned
off.
Secure Boot Mode Selects the Secure Boot operation mode.
Default: Deployed Mode
NOTE: Deployed Mode should be selected for normal operation of Secure
Boot.
Expert Key Management
Enable Custom Mode Enables or disables the keys in the PK, KEK, db, and dbx security key databases
to be modified.
Default: OFF
Custom Mode Key Management Selects the custom values for expert key management.
Default: PK
Table 5. System setup options—Integrated Devices menu
Integrated Devices
Date/Time
Date Sets the computer date in MM/DD/YYYY format. Changes to the date take
effect immediately.
Time Sets the computer time in HH/MM/SS 24-hour format. You can switch between
12-hour and 24-hour clock. Changes to the time take effect immediately.
Camera
Enable Camera Enables or disables the camera.
By default, Enable Camera is selected.
NOTE: The camera setup option may not be available, depending on the
configuration ordered.
Audio
Enable Audio Enables or disables all integrated audio controller.
Default: ON
Enable Microphone Enables or disables microphone.
By default, Enable Microphone is selected.
NOTE: The microphone setup option may not be available, depending on the
configuration ordered.
Enable Internal Speaker Enables or disables internal speaker.
By default, Enable Internal Speaker is selected.
USB/Thunderbolt Configuration Enables or disables booting from USB mass storage devices such as external hard
drive, optical drive, and USB drive.
By default, Enable External USB Ports is selected.
48 System setup
Table 5. System setup options—Integrated Devices menu (continued)
Integrated Devices
By default, Enable USB Boot Support is selected.
Enable Thunderbolt Boot Support Enables or disables Thunderbolt Boot Support.
Default: OFF
Enable Thunderbolt (and PCIe behind TBT)
pre-boot modules
Enables or disables to allow or disallow PCIe devices to be connected through a
Thunderbolt adapter during pre-boot.
Default: OFF
Miscellaneous Devices
Enable Fingerprint Reader Device Enables or disables the Fingerprint Reader Device.
By default, Enable Fingerprint Reader Device is selected.
Enable Fingerprint Reader Single Sign On Enables or disables the Fingerprint Reader Device's Single Sign On capability.
By default, Enable Fingerprint Reader Device's Single Sign On capability is
selected.
Table 6. System setup options—Storage menu
Storage
SATA/NVMe Operation
SATA/NVMe Operation Configures operating mode of the integrated SATA hard drive controller.
Default: AHCI/NVMe. Storage device is configured for AHCI/NVMe mode.
Storage Interface Displays the information of various onboard drives.
Port Enablement Enables or disables the M.2 PCIe SSD.
Default: ON
Drive Information Displays the information of onboard drives.
Enable MediaCard Enables to switch all media cards On/Off or set the media card to read-only
state.
By default, Enable Secure Digital (SD) Card is selected.
Table 7. System setup options—Display menu
Display
Display Brightness
Brightness on battery power Sets the screen brightness when the computer is running on battery power.
Default: 50
Brightness on AC power Sets the screen brightness when the computer is running on AC power.
Default: 100
Touchscreen
Touchscreen Enables or disables the touchscreen.
Default: ON
Full Screen Logo
Full Screen Logo Enabled or disabled the computer to display full screen logo if the image match
screen resolution.
System setup 49
Table 7. System setup options—Display menu (continued)
Display
Default: OFF
Table 8. System setup options—Connection menu
Connection
Wireless Device Enable Enable or disable internal WLAN/Bluetooth devices.
By default, WLAN is selected.
By default, Bluetooth is selected.
Enable UEFI Network Stack
Enable UEFI Network Stack Enables or disables UEFI Network Stack.
Default: ON
Wireless Radio Control
Control WLAN radio Enables to sense the connection of the computer to a wired network and
subsequently disable the selected wireless radios (WLAN and/or WWAN). Upon
disconnection from the wired network, the selected wireless radios are re-
enabled.
Default: OFF
Table 9. System setup options—Power menu
Power
Battery Configuration
Battery Configuration Enables the computer to run on battery during power usage hours. Use the below
options to prevent AC power usage between certain times of each day.
Default: Adaptive. Battery settings are adaptively optimized based on your typical
battery usage pattern.
Advanced Configuration
Enable Advanced Battery Charge
Configuration
Enables Advanced Battery Charge Configuration from the beginning of the day
to a specified work period. Advanced Battery Charged maximizes battery health
while still supporting heavy use during the work day.
Default: OFF
Peak Shift
Enable Peak Shift Enables the computer to run on battery during peak power usage hours.
Default: OFF
Thermal Management
Thermal Management Adjusts system performance, noise, and temperature.
Default: Optimized. Standard setting for balance of performance, noise, and
temperature.
USB Wake Support
Wake on Dell USB-C Dock Enables connecting a Dell USB-C Dock to wake the computer from Standby.
Default: ON
Block Sleep
Block Sleep Blocks the computer from entering Sleep (S3) mode in the operating system.
50 System setup
Table 9. System setup options—Power menu (continued)
Power
Default: OFF
NOTE: If enabled, the computer will not go to sleep, Intel Rapid Start will be
disabled automatically, and the operating system power option will be blank if
it was set to Sleep.
Lid Switch
Enable Lid Switch Enables or disables the lid switch.
Power On Lid Open Enables the computer to power up from the off state whenever the lid is opened.
Default: ON
Intel Speed Shift Technology Enables or disables the Intel Speed Shift Technology support. Setting this option
to enable allows the operating system to select the appropriate processor
performance automatically.
Default: ON
Table 10. System setup options—Security menu
Security
TPM 2.0 Security On
TPM 2.0 Security On Select whether or not the Trusted Platform Model (TPM) is visible to the OS.
Default: ON
PPI Bypass for Enable Commands Enables or disables the OS to skip BIOS Physical Presence Interface (PPI) user
prompts when issuing TPM PPI enabled and activate commands.
Default: OFF
PPI Bypass for Disable Commands Enables or disables The OS to skip BIOS PPI user prompts when issuing TPM PPI
Disable and Deactivate commands.
Default: OFF
Attestation Enable Enables to control whether the TPM Endorsement Hierarchy is available to the
OS. Disabling this setting restricts the ability to use the TPM for signature
operations.
Default: ON
Key Storage Enable Enables to control whether the TPM Endorsement Hierarchy is available to the
OS. Disabling this setting restricts the ability to use the TPM for storing owner
data.
Default: ON
SHA-256 Enables or disables the BIOS and the TPM to use the SHA-256 hash algorithm to
extend measurements into the TPM PCRs during BIOS boot.
Default: ON
Clear Enables or disables the computer to clear the PTT owner information, and
returns the PTT to the default state.
Default: OFF
PPI Bypass for Clear Commands Enables or disables the operating system to skip BIOS Physical Presence
Interface (PPI) user prompts when issuing the Clear command.
Default: OFF
TPM State Enables or disables the TPM. This is the normal operating state for the TPM
when you want to use its complete array of capabilities.
System setup 51
Table 10. System setup options—Security menu (continued)
Security
Default: Enabled
SMM Security Mitigation
SMM Security Mitigation Enables or disables additional UEFI SMM Security Mitigation protections.
Default: OFF
NOTE: This feature may cause compatibility issues or loss of functionality
with some legacy tools and applications.
Data Wipe on Next Boot
Start Data Wipe CAUTION: This Secure Wipe Operation deletes information in a way
that it cannot be reconstructed.
If enabled, the BIOS will queue up a data wipe cycle for storage devices that are
connected to the motherboard on the next reboot.
Default: OFF
Absolute
Absolute Enables, disables or permanently disable the BIOS module interface of the
optional Absolute Persistence Module service from Absolute Software.
Default: Enabled
UEFI Boot Path Security
UEFI Boot Path Security Enables or disables the system to prompt the user to enter the Admin password
when booting a UEFI boot path from the F12 boot menu.
Default: Always Except Internal HDD
Table 11. System setup options—Passwords menu
Passwords
Admin Password Sets, Changes, or deletes the administrator (admin) password (sometimes called
the "setup" password).
System Password Sets, Changes, or deletes the system password.
Password Configuration
Upper Case Letter Enables or disables the requirement for at least one upper case letter.
Default: OFF
Lower Case Letter Enables or disables the requirement for at least one lower case letter.
Default: OFF
Digit Enables or disables the requirement for at least one digit number.
Default: OFF
Special Character Enables or disables the requirement for at least one special character.
Default: OFF
Minimum Characters Specify the minimum number of characters allowed for the password.
Default: 4
Password Bypass
Password Bypass Bypass the System (Boot) Password and the internal hard drive password
prompts during a system restart.
52 System setup
Table 11. System setup options—Passwords menu (continued)
Passwords
Default: Disabled
Password Changes
Enable Non-Admin Password Changes Enables or disables the user to change the system and hard drive password
without the need for admin password.
Default: ON
Admin Setup Lockout
Enable Admin Setup Lockout Enables or disables the user from entering BIOS Setup when an Admin Password
is set.
Default: OFF
Master Password Lockout
Enable Master Password Lockout Enables or disables the master password support.
Default: OFF
Table 12. System setup options—Update, Recovery menu
Update, Recovery
UEFI Capsule Firmware Updates
Enable UEFI Capsule Firmware Updates Enables or disables BIOS updates through UEFI capsule update packages.
Default: ON
BIOS Recovery from Hard Drive
BIOS Recovery from Hard Drive Enables the computer to recover from a bad BIOS image, as long as the Boot
Block portion is intact and functioning.
Default: ON
NOTE: BIOS recovery is designed to fix the main BIOS block and cannot work
if the Boot Block is damaged. In addition, this feature cannot work in the
event of EC corruption, ME corruption, or a hardware issue. The recovery
image must exist on an unencrypted partition on the drive.
BIOS Downgrade
Allow BIOS Downgrade Controls flashing of the system firmware to previous revisions.
Default: ON
SupportAssist OS Recovery
SupportAssist OS Recovery Enables or disables the boot flow for SupportAssist OS Recovery tool in the event
of certain system errors.
Default: ON
BIOSConnect
BIOSConnect Enables or disables cloud Service OS recover if the main operating system fails to
boot with the number of failures equal to or greater than the value specified by
the Auto OS Recovery Threshold setup option.
Default: ON
Dell Auto OS Recovery Threshold
Dell Auto OS Recovery Threshold Controls the automatic boot flow for SupportAssist System Resolution Console
and for Dell operating system Recovery tool.
System setup 53
Table 12. System setup options—Update, Recovery menu (continued)
Update, Recovery
Default: 2
Table 13. System setup options—System Management menu
System Management
Service Tag
Service Tag Displays the Service Tag of the computer.
Asset Tag
Asset Tag Creates a system Asset Tag that can be used by an IT administrator to uniquely
identify a particular system. Once set in BIOS, the Asset Tag cannot be changed.
AC Behavior
Wake on AC Enables the computer to turn on and go to boot when AC power is supplied to the
computer.
Default: OFF
Wake on LAN
Wake on LAN Enables or disables the computer to turn on by a special LAN signal.
Default: Disabled
Auto On Time
Auto On Time Enables the computer to automatically power on for defined days and times.
Default: Disabled. The system will not automatically power up.
Table 14. System setup options—Keyboard menu
Keyboard
Numlock Enable
Enable Numlock Enables or disables Numlock when the computer boots.
Default: ON
Fn Lock Options
Fn Lock Options Enables or disables the Fn lock mode.
Default: ON
Lock Mode Default: Lock Mode Secondary. Lock Mode Secondary = If this option is selected,
the F1-F12 keys scan the code for their secondary functions.
Keyboard Illumination
Keyboard Illumination Configures the operating mode of the keyboard illumination feature.
Default: Bright. Enable the keyboard illumination feature at 100% brightness level.
Keyboard Backlight Timeout on AC
Keyboard Backlight Timeout on AC Configures the timeout value for the keyboard when an AC adapter is connected
to the computer. The keyboard backlight timeout value is only effect when the
backlight is enabled.
Default: 10 seconds
Keyboard Backlight Timeout on Battery
54 System setup
Table 14. System setup options—Keyboard menu (continued)
Keyboard
Keyboard Backlight Timeout on Battery Configures the timeout value for the keyboard when the computer is running on
battery. The keyboard backlight timeout value is only effect when the backlight is
enabled.
Default: 10 seconds
Table 15. System setup options—Pre-boot Behavior menu
Pre-boot Behavior
Adapter Warnings
Enable Dock Warning Messages Enables or disables dock warning messages.
Default: ON
Warnings and Errors
Warnings and Errors Selects an action on encountering a warning or error during boot.
Default: Prompt on Warnings and Errors. Stop, prompt, and wait for user input
when warnings or errors are detected.
NOTE: Errors deemed critical to the operation of the computer hardware will
always halt the computer.
USB-C Warnings
Enable Dock Warning Messages Enables or disables dock warning messages.
Default: ON
Fastboot
Fastboot Configures the speed of the UEFI boot process.
Default: Thorough. Performs complete hardware and configuration initialization
during boot.
Extend BIOS POST Time
Extend BIOS POST Time Configures the BIOS POST (Power-On Self-Test) load time.
Default: 0 seconds
MAC Address Pass-Through
MAC Address Pass-Through Replaces the external NIC MAC address (in a supported dock or dongle) with the
selected MAC address from the computer.
Default: System Unique MAC Address.
Sign of Life
Early Logo Display Display Logo Sign of Life.
Default: ON
Early Keyboard Backlight Keyboard Backlight Sign of Life.
Default: ON
Mouse/Touchpad
Mouse/Touchpad Defines how the computer handles mouse and touchpad input.
Default: Touchpad and PS/2 Mouse. Leave the integrated touchpad enabled
when an external PS/2 mouse is present.
System setup 55
Table 16. System setup options—Virtualization menu
Virtualization
Intel Virtualization Technology
Enable Intel Virtualization Technology (VT) Enables the computer to run a virtual machine monitor (VMM).
Default: ON
VT for Direct I/O
Enable Intel VT for Direct I/O Enables the computer to perform Virtualization Technology for Direct I/O (VT-d).
VT-d is an Intel method that provides virtualization for memory map I/O.
Default: ON
Table 17. System setup options—Performance menu
Performance
Multi-Core Support
Active Cores Changes the number of CPU cores available to the operating system. The default
value is set to the maximum number of cores.
Default: All Cores
Intel SpeedStep
Enable Intel SpeedStep Technology Enables or disables the Intel SpeedStep Technology to dynamically adjust
processor voltage and core frequency, decreasing average power consumption
and heat production.
Default: ON
Enable C-State Control Enables or disables the CPU's ability to enter and exit low-power states.
Default: ON
Intel Turbo Boost Technology
Enable Intel Turbo Boost Technology Enabled or disabled the Intel TurboBoost mode of the processor. If enabled,
the Intel TurboBoost driver increases the performance of the CPU or graphics
processor.
Default: ON
Intel Hyper-Threading Technology
Enable Intel Hyper-Threading Technology Enabled or disabled the Intel Hyper-Threading mode of the processor. If enabled,
the Intel Hyper-Threading increases the efficiency of the processor resources
when multiple threads run on each core.
Default: ON
Table 18. System setup options—System Logs menu
System Logs
BIOS Event Log
Clear Bios Event Log Select keep or clear BIOS events.
Default: Keep
Thermal Event Log
Clear Thermal Event Log Select keep or clear Thermal events.
Default: Keep
Power Event Log
56 System setup
Table 18. System setup options—System Logs menu (continued)
System Logs
Clear POWER Event Log Select keep or clear Power events.
Default: Keep
Clearing CMOS settings
About this task
CAUTION: Clearing CMOS settings will reset the BIOS settings on your computer.
Steps
1. Turn off your computer.
2. Remove the base cover.
NOTE: The battery must be disconnected from the system board (see Step 5 in Removing the base cover
3. Press and hold the power button for 15 seconds to drain the flea power.
4. Before you turn on your computer, follow the steps in Installing the base cover.
5. Turn on your computer.
Clearing BIOS (System Setup) and System passwords
About this task
To clear the system or BIOS passwords, contact Dell technical support as described at www.dell.com/contactdell.
NOTE: For information on how to reset Windows or application passwords, refer to the documentation accompanying
Windows or your application.
System setup 57
Troubleshooting
Handling swollen Lithium-ion batteries
Like most laptops, Dell laptops use lithium-ion batteries. One type of lithium-ion battery is the lithium-ion polymer battery.
Lithium-ion polymer batteries have increased in popularity in recent years and have become standard in the electronics industry
due to customer preferences for a slim form factor (especially with newer ultra-thin laptops) and long battery life. Inherent to
lithium-ion polymer battery technology is the potential for swelling of the battery cells.
Swollen battery may impact the performance of the laptop. To prevent possible further damage to the device enclosure or
internal components leading to malfunction, discontinue the use of the laptop and discharge it by disconnecting the AC adapter
and letting the battery drain.
Swollen batteries should not be used and should be replaced and disposed of properly. We recommend contacting Dell product
support for options to replace a swollen battery under the terms of the applicable warranty or service contract, including options
for replacement by a Dell authorized service technician.
The guidelines for handling and replacing Lithium-ion batteries are as follows:
●Exercise caution when handling Lithium-ion batteries.
●Discharge the battery before removing it from the system.
To discharge the battery, unplug the AC adapter from the system and operate the system only on battery power. When the
system will no longer power on when the power button is pressed, the battery is fully discharged.
●Do not crush, drop, mutilate, or penetrate the battery with foreign objects.
●Do not expose the battery to high temperatures, or disassemble battery packs and cells.
●Do not apply pressure to the surface of the battery.
●Do not bend the battery.
●Do not use tools of any type to pry on or against the battery.
●If a battery gets stuck in a device as a result of swelling, do not try to free it as puncturing, bending, or crushing a battery
can be dangerous.
●Do not attempt to reassemble a damaged or swollen battery into a laptop.
●Swollen batteries should be returned to Dell in an approved shipping container (provided by Dell), to comply with
transportation regulations or disposed at an approved recycling center.
Contact Dell product support at https://www.dell.com/support for assistance and further instructions.
●Using a non-Dell or incompatible battery may increase the risk of fire or explosion. Replace the battery only with a
compatible battery purchased from Dell that is designed to work with your Dell computer. Do not use a battery from other
computers with your computer. Always purchase genuine batteries from https://www.dell.com or otherwise directly from
Dell.
Lithium-ion batteries can swell for various reasons such as age, number of charge cycles, or exposure to high heat. For more
information on how to improve the performance and lifespan of the laptop battery and to minimize the possibility of occurrence
of the issue, see Dell Laptop Battery - Frequently Asked Questions.
Recovering the operating system
When your computer is unable to boot to the operating system even after repeated attempts, it automatically starts Dell
SupportAssist OS Recovery.
Dell SupportAssist OS Recovery is a standalone tool that is preinstalled in all Dell computers installed with Windows 10 operating
system. It consists of tools to diagnose and troubleshoot issues that may occur before your computer boots to the operating
system. It enables you to diagnose hardware issues, repair your computer, back up your files, or restore your computer to its
factory state.
5
58 Troubleshooting
You can also download it from the Dell Support website to troubleshoot and fix your computer when it fails to boot into their
primary operating system due to software or hardware failures.
For more information about the Dell SupportAssist OS Recovery, see Dell SupportAssist OS Recovery User's Guide at
www.dell.com/support.
SupportAssist | On-board Diagnostics
About this task
The SupportAssist | On-board Diagnostics performs a complete check of your hardware.
This diagnostic is the new on-board diagnostic tool and replaces the ePSA 3.0 diagnostics. It has a clean and modern user
interface, quicker tests, simplified messaging.
SupportAssist | On-board Diagnostics can be initiated by one of the following methods:
●Pressing F12 to enter one-time Boot Menu and selecting Diagnostics to initiate the diagnostics OR Fn + Power
●BIOS POST detecting a hardware failure or error and initiating the diagnostics
The SupportAssist | On-board Diagnostics is embedded with the BIOS and is launched by the BIOS internally. The embedded
system diagnostics provides a set of options for particular devices or device groups allowing you to:
●Run tests in either Quick Test Mode or Advanced Test Mode
●Run thorough tests to introduce additional test options to provide extra information about the failed device(s)
●Run tests in either Automatic Mode or Interactive Test Mode
●Run interactive tests on LCD panel and keyboard
●Display or save test results
●View status messages that indicate if the tests are completed successfully
●View error messages that indicate if problems were encountered during the test
NOTE: Some tests for specific devices require user interaction. Ensure that you are present at the computer terminal when
the diagnostic tests are performed.
For more information, see SupportAssist Pre-Boot System Performance Check.
System diagnostic lights
When static, the power and battery-charge status light indicates the power mode that your computer is in. When blinking
in different patterns, the power and battery-charge status light indicates the respective issues that your computer is
encountering.
Static power and battery-charge status light
The following table lists the status of your computer based on the power and battery-charge status light.
Table 19. Power and battery-charge status light
Power and battery-charge status light Status of computer
Solid white ●The power adapter is connected and the battery is fully charged.
●The power adapter is connected and the battery has more than five
percent charge.
Amber The computer is running on battery and the battery has less than five
percent charge.
Off The computer is in sleep state, hibernation, or turned off.
Blinking power and battery-charge status light
The power and battery-status light blinks alternately between amber and off to indicate issues that your computer is
encountering.
For example, the power and battery-status light blinks amber two times followed by a pause, and then blinks white three times
followed by a pause. This 2,3 pattern continues until the computer is turned off indicating no memory or RAM is detected.
Troubleshooting 59
The following table shows the different power and battery-status light patterns and the associated issues.
Table 20. LED codes
Diagnostic light codes Problem description
2,1 Processor failure
2,2 System board: BIOS or ROM (Read-Only Memory) failure
2,3 No memory or RAM (Random-Access Memory) detected
2,4 Memory or RAM (Random-Access Memory) failure
2,5 Invalid memory installed
2,6 System-board or chipset error
2,7 Display failure
2,8 Display power failure
3,1 Coin-cell battery failure
3,2 PCI, video card/chip failure
3,3 Recovery image not found.
3,4 Recovery image found but invalid.
3,5 Power-rail failure
3,6 System BIOS Flash incomplete
3,7 Management Engine (ME) error
Flea power release
About this task
Flea power is the residual static electricity that remains on the computer even after it has been powered off and the battery has
been disconnected from the system board. The following procedure provides the instructions on how to release the flea power:
Steps
1. Turn off your computer.
2. Remove the base cover.
NOTE: The battery must be disconnected from the system board (see Step 5 in Removing the base cover
3. Press and hold the power button for 15 seconds to drain the flea power.
4. Install the base cover.
5. Turn on your computer.
WiFi power cycle
About this task
If your computer is unable to access the Internet due to WiFi connectivity issues, a WiFi power cycle procedure may be
performed. The following procedure provides the instructions on how to conduct a WiFi power cycle:
NOTE: Some ISPs (Internet Service Providers) provide a modem/router combo device.
Steps
1. Turn off your computer.
60 Troubleshooting
2. Turn off the modem.
3. Turn off the wireless router.
4. Wait for 30 seconds.
5. Turn on the wireless router.
6. Turn on the modem.
7. Turn on your computer.
Troubleshooting 61
Getting help and contacting Dell
Self-help resources
You can get information and help on Dell products and services using these self-help resources:
Table 21. Self-help resources
Self-help resources Resource location
Information about Dell products and services www.dell.com
My Dell app
Tips
Contact Support In Windows search, type Contact Support, and press
Enter.
Online help for operating system www.dell.com/support/windows
www.dell.com/support/linux
Access top solutions, diagnostics, drivers and downloads, and
learn more about your computer through videos, manuals and
documents.
Your Dell computer is uniquely identified by a Service Tag or
Express Service Code. To view relevant support resources for
your Dell computer, enter the Service Tag or Express Service
Code at www.dell.com/support.
For more information on how to find the Service Tag for your
computer, see Locate the Service Tag on your computer.
Dell knowledge base articles for a variety of computer
concerns
1. Go to www.dell.com/support.
2. On the menu bar at the top of the Support page, select
Support > Knowledge Base.
3. In the Search field on the Knowledge Base page, type the
keyword, topic, or model number, and then click or tap the
search icon to view the related articles.
Contacting Dell
To contact Dell for sales, technical support, or customer service issues, see www.dell.com/contactdell.
NOTE: Availability varies by country/region and product, and some services may not be available in your country/region.
NOTE: If you do not have an active Internet connection, you can find contact information about your purchase invoice,
packing slip, bill, or Dell product catalog.
6
62 Getting help and contacting Dell