Table of Contents
- XPS 13 Service Manual
- Before working inside your computer
- After working inside your computer
- Removing the base cover
- Replacing the base cover
- Removing the battery
- Replacing the battery
- Removing the solid-state drive
- Replacing the solid-state drive
- Removing the wireless card
- Replacing the wireless card
- Removing the speakers
- Replacing the speakers
- Removing the coin-cell battery
- Replacing the coin-cell battery
- Removing the heat sink
- Replacing the heat sink
- Removing the battery-status light cable
- Replacing the battery-status light cable
- Removing the touchpad
- Replacing the touchpad
- Removing the I/O-board cable
- Replacing the I/O-board cable
- Removing the I/O board
- Replacing the I/O board
- Removing the display assembly
- Replacing the display assembly
- Removing the display hinge cover
- Replacing the display hinge cover
- Removing the antenna
- Replacing the antenna
- Removing the system board
- Replacing the system board
- Removing the power-adapter port
- Replacing the power-adapter port
- Removing the fan
- Replacing the fan
- Removing the keyboard
- Replacing the keyboard
- Removing the palm-rest assembly
- Replacing the palm-rest assembly
- Downloading drivers
- System setup
- Troubleshooting
- Getting help and contacting Dell
DELL 9360 User Manual
Displayed below is the user manual for 9360 by DELL which is a product in the Notebooks category. This manual has pages.
Related Manuals
XPS 13
Service Manual
Computer Model: XPS 9360
Regulatory Model: P54G
Regulatory Type: P54G002
Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make
better use of your product.
CAUTION: A CAUTION indicates either potential damage to hardware or
loss of data and tells you how to avoid the problem.
WARNING: A WARNING indicates a potential for property damage,
personal injury, or death.
Copyright © 2017 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other
trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be
trademarks of their respective owners.
2017 - 09
Rev. A01
Contents
Before working inside your computer........................... 10
Before you begin .....................................................................................10
Safety instructions...................................................................................10
Recommended tools................................................................................. 11
Screw list................................................................................................. 12
After working inside your computer..............................14
Removing the base cover............................................. 15
Procedure................................................................................................ 15
Replacing the base cover..............................................18
Procedure................................................................................................ 18
Removing the battery...................................................19
Prerequisites............................................................................................ 19
Procedure................................................................................................ 19
Replacing the battery...................................................22
Procedure................................................................................................22
Post-requisites........................................................................................ 22
Removing the solid-state drive.....................................23
Prerequisites............................................................................................23
Procedure................................................................................................23
3
Replacing the solid-state drive.....................................25
Procedure............................................................................................... 25
Post-requisites........................................................................................ 26
Removing the wireless card..........................................27
Prerequisites............................................................................................27
Procedure................................................................................................27
Replacing the wireless card..........................................29
Procedure............................................................................................... 29
Post-requisites........................................................................................ 30
Removing the speakers.................................................31
Prerequisites............................................................................................ 31
Procedure................................................................................................ 31
Replacing the speakers................................................ 33
Procedure................................................................................................33
Post-requisites........................................................................................ 33
Removing the coin-cell battery.................................... 34
Prerequisites............................................................................................34
Procedure................................................................................................34
Replacing the coin-cell battery.................................... 36
Procedure............................................................................................... 36
Post-requisites........................................................................................ 36
Removing the heat sink................................................37
Prerequisites............................................................................................37
Procedure................................................................................................37
4
Replacing the heat sink................................................39
Procedure............................................................................................... 39
Post-requisites........................................................................................ 39
Removing the battery-status light cable...................... 40
Prerequisites........................................................................................... 40
Procedure............................................................................................... 40
Replacing the battery-status light cable.......................42
Procedure................................................................................................42
Post-requisites........................................................................................ 42
Removing the touchpad............................................... 43
Prerequisites............................................................................................43
Procedure................................................................................................43
Replacing the touchpad............................................... 46
Procedure............................................................................................... 46
Post-requisites........................................................................................ 46
Removing the I/O-board cable .................................... 47
Prerequisites............................................................................................47
Procedure................................................................................................47
Replacing the I/O-board cable .................................... 49
Procedure............................................................................................... 49
Post-requisites........................................................................................ 49
Removing the I/O board.............................................. 50
Prerequisites........................................................................................... 50
Procedure............................................................................................... 50
5
Replacing the I/O board...............................................53
Procedure............................................................................................... 53
Post-requisites........................................................................................ 53
Removing the display assembly....................................54
Prerequisites........................................................................................... 54
Procedure............................................................................................... 54
Replacing the display assembly....................................60
Procedure............................................................................................... 60
Post-requisites......................................................................................... 61
Removing the display hinge cover................................62
Prerequisites........................................................................................... 62
Procedure............................................................................................... 62
Replacing the display hinge cover................................ 64
Procedure............................................................................................... 64
Post-requisites........................................................................................ 64
Removing the antenna................................................. 65
Prerequisites........................................................................................... 65
Procedure............................................................................................... 65
Replacing the antenna..................................................67
Procedure................................................................................................67
Post-requisites........................................................................................ 67
Removing the system board.........................................68
Prerequisites........................................................................................... 68
Procedure............................................................................................... 68
6
Replacing the system board......................................... 73
Procedure................................................................................................73
Post-requisites.........................................................................................74
Entering the Service Tag in the BIOS setup program...............................74
Removing the power-adapter port............................... 75
Prerequisites............................................................................................75
Procedure................................................................................................75
Replacing the power-adapter port................................77
Procedure................................................................................................77
Post-requisites.........................................................................................77
Removing the fan.........................................................78
Prerequisites............................................................................................78
Procedure................................................................................................78
Replacing the fan..........................................................81
Procedure................................................................................................ 81
Post-requisites......................................................................................... 81
Removing the keyboard............................................... 82
Prerequisites............................................................................................82
Procedure............................................................................................... 83
Replacing the keyboard................................................86
Procedure............................................................................................... 86
Post-requisites........................................................................................ 86
Removing the palm-rest assembly................................87
Prerequisites............................................................................................87
Procedure............................................................................................... 88
7
Replacing the palm-rest assembly............................... 89
Procedure............................................................................................... 89
Post-requisites........................................................................................ 89
Downloading drivers..................................................... 91
Downloading the audio driver...................................................................91
Downloading the graphics driver..............................................................91
Downloading the USB 3.0 driver..............................................................92
Downloading the Wi-Fi driver.................................................................. 92
Downloading the media-card reader driver..............................................92
Downloading the chipset driver............................................................... 93
Downloading the network driver............................................................. 93
System setup...............................................................95
Boot Sequence....................................................................................... 95
Navigation keys.......................................................................................95
BIOS overview........................................................................................ 96
Entering BIOS setup program..................................................................96
System setup options.............................................................................. 97
System and setup password.................................................................. 104
Assigning a system password and setup password.......................... 105
Deleting or changing an existing system and/or setup password.....105
Clearing CMOS settings.................................................................. 106
Clearing forgotten passwords.......................................................... 106
Troubleshooting.......................................................... 107
Flashing the BIOS.................................................................................. 107
Flashing BIOS (USB key)....................................................................... 107
Enhanced Pre-Boot System Assessment (ePSA) diagnostics................108
8
Running the ePSA diagnostics.........................................................108
System diagnostic lights........................................................................ 109
Flea power release..................................................................................110
Wi-Fi power cycle....................................................................................111
Getting help and contacting Dell................................. 112
Self-help resources.................................................................................112
Contacting Dell....................................................................................... 113
9
Before working inside your
computer
NOTE: The images in this document may dier from your computer
depending on the conguration you ordered.
Before you begin
1 Save and close all open les and exit all open applications.
2 Shut down your computer. Click Start → Power → Shut down.
NOTE: If you are using a dierent operating system, see the
documentation of your operating system for shut-down instructions.
3 Disconnect your computer and all attached devices from their electrical outlets.
4 Disconnect all attached network devices and peripherals, such as keyboard,
mouse, and monitor from your computer.
5 Remove any media card and optical disc from your computer, if applicable.
Safety instructions
Use the following safety guidelines to protect your computer from potential damage
and ensure your personal safety.
WARNING: Before working inside your computer, read the safety
information that shipped with your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
WARNING: Disconnect all power sources before opening the computer
cover or panels. After you nish working inside the computer, replace all
covers, panels, and screws before connecting to the electrical outlet.
CAUTION: To avoid damaging the computer, ensure that the work surface is
at and clean.
10
CAUTION: To avoid damaging the components and cards, handle them by
their edges, and avoid touching pins and contacts.
CAUTION: You should only perform troubleshooting and repairs as
authorized or directed by the Dell technical assistance team. Damage due to
servicing that is not authorized by Dell is not covered by your warranty. See
the safety instructions that shipped with the product or at www.dell.com/
regulatory_compliance.
CAUTION: Before touching anything inside your computer, ground yourself
by touching an unpainted metal surface, such as the metal at the back of
the computer. While you work, periodically touch an unpainted metal surface
to dissipate static electricity, which could harm internal components.
CAUTION: When you disconnect a cable, pull on its connector or on its pull
tab, not on the cable itself. Some cables have connectors with locking tabs
or thumb-screws that you must disengage before disconnecting the cable.
When disconnecting cables, keep them evenly aligned to avoid bending any
connector pins. When connecting cables, ensure that the ports and
connectors are correctly oriented and aligned.
CAUTION: Press and eject any installed card from the media-card reader.
Recommended tools
The procedures in this document may require the following tools:
• Phillips screwdriver
• Torx #5 (T5) screwdriver
• Plastic scribe
11
Screw list
The following table provides the list of screws that are used for securing dierent
components.
Table 1. Screw list
Component Secured to Screw type Quantity Screw image
Antenna Display back-
cover
M2x4 4
Display hinges Display back-
cover
M2.5x6 4
Fingerprint
reader bracket
(optional)
Palm-rest
assembly
M1.6x1.5 1
Keyboard Palm-rest
assembly
M1.6x1.5 30
Touchpad Palm-rest
assembly
M2x2 4
Speakers Palm-rest
assembly
M2x2 4
Power-
adapter port
Palm-rest
assembly
M2x3 1
System board Palm-rest
assembly
M1.6x3 7
I/O board Palm-rest
assembly
M1.6x3 2
Heat sink System board M2x3 4
Hinge
brackets
Palm-rest
assembly
M2.5x4 4
Hard drive
(SSD)
Hard-drive
(SSD) bracket
M2x2 1
12
Component Secured to Screw type Quantity Screw image
Wireless card System board M2x3 1
Display-cable
bracket
System board M2x3 2
Battery Palm-rest
assembly
M2x2 3
Battery Palm-rest
assembly
M1.6x4 1
Base cover Palm-rest
assembly
M2x3, Torx 8
Base cover Palm-rest
assembly
M1.6x6 1
13
After working inside your
computer
CAUTION: Leaving stray or loose screws inside your computer may severely
damage your computer.
1 Replace all screws and ensure that no stray screws remain inside your computer.
2 Connect any external devices, peripherals, or cables you removed before working
on your computer.
3 Replace any media cards, discs, or any other parts that you removed before
working on your computer.
4 Connect your computer and all attached devices to their electrical outlets.
5 Turn on your computer.
14
Removing the base cover
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
1 Using your ngertips, open the system badge.
2 Remove the screw (M1.6x6) that secures the base cover to the palm-rest
assembly.
15
3 Remove the eight screws (M2x3, Torx) that secure the base cover to the palm-
rest assembly.
Figure 1. Removing the base cover
1screws (9) 2 system badge
3 base cover
4 Starting from the back of the computer, pry up the base cover using a plastic
scribe.
16
5 Lift the base cover o the palm-rest assembly.
Figure 2. Removing the base cover
1 palm-rest assembly 2 base cover
3 plastic scribe
17
Replacing the base cover
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
1 Align the screw holes on the base cover with the screw holes on the palm-rest
assembly and snap the base cover into place.
2 Using your ngertips, open the system badge.
3 Replace the screw (M1.6x4) under the system badge that secures the base
cover to the palm-rest assembly.
4 Replace the eight screws (M2x3, Torx) that secure the base cover to the palm-
rest assembly.
18
Removing the battery
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Prerequisites
Remove the base cover.
Procedure
1 Disconnect the battery cable from the system board.
19
2 Peel o the tape that secures the speaker cable to the battery.
Figure 3. Removing the battery
1battery cable 2 speaker cable
3 tape (6)
3 Remove the screw (M1.6x4) that secures the battery to the palm-rest assembly.
4 Remove the three screws (M2x2) that secure the battery to the palm-rest
assembly.
20
5 Lift the battery o the palm-rest assembly.
Figure 4. Removing the battery
1 palm-rest assembly 2 battery
3 screws (4)
6 Turn the computer over, open the display, and press the power button for about
5 seconds to ground the computer.
21
Replacing the battery
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
1 Align the screw holes on the battery with the screw holes on the palm-rest
assembly.
2 Replace the three screws (M2x3) that secure the battery to the palm-rest
assembly.
3 Replace the screw (M1.6x4) that secures the battery to the palm-rest assembly.
4 Connect the battery cable to the system board.
Post-requisites
Replace the base cover.
22
Removing the solid-state drive
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
CAUTION: Solid-state drives are fragile. Exercise care when handling the
solid-state drive.
CAUTION: To avoid data loss, do not remove the solid-state drive while the
computer is in sleep or on state.
Prerequisites
1 Remove the base cover.
2 Remove the battery.
Procedure
1 Remove the screw (M2x2) that secures the solid-state drive to the system
board.
23
2 Slide and remove the solid-state drive from the solid-state drive slot.
Figure 5. Removing the solid-state drive
1solid-state drive slot 2 screw
3 solid-state drive
24
Replacing the solid-state drive
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
CAUTION: Solid-state drives are fragile. Exercise care when handling the
solid-state drive.
Procedure
1 Align the notches on the solid-state drive with the tabs in the solid-state drive
slot.
2 Slide the solid-state drive at an angle into the solid-state drive slot.
25
3 Press the other end of the solid-state drive down and replace the screw (M2x2)
that secures the solid-state drive to the system board.
Figure 6. Replacing the solid-state drive
1solid-state drive slot 2 tab
3 notch 4 solid-state drive
5 screw
Post-requisites
1 Replace the battery.
2 Replace the base cover.
26
Removing the wireless card
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Prerequisites
1 Remove the base cover.
2 Remove the battery.
Procedure
1 Remove the screw (M2x3) that secures the wireless-card bracket and the
wireless card to the system board.
2 Lift the wireless-card bracket o the wireless card.
3 Disconnect the antenna cables from the wireless card.
27
4 Slide and remove the wireless card out of the wireless-card slot.
Figure 7. Removing the wireless card
1wireless-card bracket 2 screw
3 antenna cables (2) 4 wireless card
5 wireless-card slot
28
Replacing the wireless card
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
1 Align the notches on the wireless card with the tabs in the wireless-card slot.
CAUTION: To avoid damage to the wireless card, never place cables
under the wireless card.
2 Slide the wireless-card at an angle into the wireless-card slot.
3 Connect the antenna cables to the wireless card.
The following table provides the antenna cable color scheme for the wireless
card supported by your computer.
Table 2. Antenna-cable color scheme
Connectors on the wireless card Antenna-cable color
Main (white triangle) White
Auxiliary (black triangle) Black
4 Press the other end of the wireless card down.
5 Place the wireless-card bracket on the wireless card.
29
Removing the speakers
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Prerequisites
1 Remove the base cover.
2 Remove the battery.
Procedure
1 Disconnect the speaker cable from the system board.
2 Remove the four screws (M2x2) that secure the speakers to the palm-rest
assembly.
3 Note the speaker-cable routing and peel o the tape that secures the speaker
cable to the system board.
31
4 Lift the speakers, along with its cables, o the palm-rest assembly.
Figure 9. Removing the speakers
1tape (2) 2 system board
3 speaker cable 4 screws (4)
5 speakers (2) 6 palm-rest assembly
32
Replacing the speakers
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
1 Using the alignment posts on the palm-rest assembly, place the speakers on the
palm-rest assembly.
2 Replace the four screws (M2x2) that secure the speakers to the palm-rest
assembly.
3 Route the speaker cable on the system board and adhere the tape to the system
board.
4 Connect the speaker cable to the system board.
5 Adhere the tape securing the speaker cable to the system board.
Post-requisites
1 Replace the battery.
2 Replace the base cover.
33
Removing the coin-cell battery
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
CAUTION: Removing the coin-cell battery resets the BIOS setup program’s
settings to default. It is recommended that you note the BIOS setup
program’s settings before removing the coin-cell battery.
Prerequisites
1 Remove the base cover.
2 Remove the battery.
Procedure
1 Disconnect the coin-cell battery cable from the system board.
34
2 Note the location of the coin-cell battery and pry it o the palm-rest assembly.
Figure 10. Removing the coin-cell battery
1coin-cell battery cable 2 palm-rest assembly
3 coin-cell battery
35
Replacing the coin-cell battery
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
1 Adhere the coin-cell battery to the palm-rest assembly.
2 Connect the coin-cell battery cable to the system board.
Post-requisites
1 Replace the battery.
2 Replace the base cover.
36
Removing the heat sink
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
WARNING: The heat sink may become hot during normal operation. Allow
sucient time for the heat sink to cool before you touch it.
CAUTION: For maximum cooling of the processor, do not touch the heat
transfer areas on the heat sink. The oils in your skin can reduce the heat
transfer capability of the thermal grease.
Prerequisites
1 Remove the base cover.
2 Remove the battery.
Procedure
1 In sequential order (as indicated on the heat sink), remove the screws that
secure the heat sink to the system board.
37
2 Lift the heat sink o the system board.
Figure 11. Removing the heat sink
1 heat sink 2 M2x3 screws (4)
38
Replacing the heat sink
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
CAUTION: Incorrect alignment of the heat sink can damage the system
board and processor.
NOTE: The original thermal grease can be reused if the original system
board and heat sink are reinstalled together. If either the system board or
the heat sink is replaced, use the thermal pad provided in the kit to ensure
that thermal conductivity is achieved.
Procedure
1 Align the screw holes on the heat sink with the screw holes on the system board.
2 Replace the screws that secure the heat sink to the system board in the reverse
order (as indicated on the heat sink).
Post-requisites
1 Replace the battery.
2 Replace the base cover.
39
Removing the battery-status
light cable
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
NOTE: The battery-status light cable is an assembly that includes LED
indicators and a digital-array microphone.
Prerequisites
1 Remove the base cover.
2 Remove the battery.
Procedure
1 Peel o the tape that secures the battery-status light cable to the keyboard-
controls board.
2 Open the latch and disconnect the battery-status light cable from the keyboard-
controls board.
3 Peel o the tape that secures the battery-status light cable to the palm-rest
assembly.
40
4 Note the battery-status light cable routing and peel o the cable from the palm-
rest assembly.
Figure 12. Removing the battery-status light cable
1tape 2 latch
3 keyboard-controls board 4 battery-status light cable
5 palm-rest assembly
41
Replacing the battery-status
light cable
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
NOTE: The battery-status light cable is an assembly that includes LED
indicators and a digital-array microphone.
Procedure
1 Using the alignment posts, place the battery-status light cable on the palm-rest
assembly.
2 Route the battery-status light cable through the routing guides and adhere it to
the palm-rest assembly.
3 Adhere the tape that secures the battery-status light cable to the palm-rest
assembly.
4 Slide the battery-status light cable into the battery-status light cable connector
and close the latch to secure the cable.
5 Adhere the tape that secures the battery-status light cable to the keyboard-
controls board.
Post-requisites
1 Replace the battery.
2 Replace the base cover.
42
Removing the touchpad
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Prerequisites
1 Remove the base cover.
2 Remove the battery.
Procedure
1 Open the latch and disconnect the touchpad cable from the system board.
43
2 Peel o the touchpad cable from the keyboard and palm-rest assembly.
Figure 13. Removing the touchpad cable
1 latch 2 touchpad cable
3 Remove the four screws (M2x2) that secure the touchpad to the palm-rest
assembly. If applicable, peel o any foam adhering the touchpad to the palm-rest
assembly.
44
4 Lift the touchpad from the inner edge and remove it from the palm-rest
assembly.
Figure 14. Removing the touchpad
1 screws (4) 2 palm-rest assembly
3 touchpad
45
Replacing the touchpad
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
1 Align the screw holes on the touchpad with the screw holes on the palm-rest
assembly.
2 Replace the four screws (M2x2) that secure the touchpad to the palm-rest
assembly.
3 Slide the touchpad cable into the connector on the system board and close the
latch to secure the cable.
4 Route the touchpad cable and adhere the cable to the keyboard and palm-rest
assembly.
Post-requisites
1 Replace the battery.
2 Replace the base cover.
46
Removing the I/O-board cable
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Prerequisites
1 Remove the base cover.
2 Remove the battery.
Procedure
1 Open the latches and disconnect the I/O-board cable from the system board and
the I/O board.
47
2 Note the I/O-board cable routing as well as its orientation, and then peel o the
cable from the keyboard.
Figure 15. Removing the I/O-board cable
1latches (2) 2 I/O-board cable
3 keyboard
48
Replacing the I/O-board cable
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
1 Slide both ends of the I/O-board cable into their connectors on the system board
and I/O board, then close the latches to secure the cable.
2 Adhere the I/O-board cable to the keyboard.
Post-requisites
1 Replace the battery.
2 Replace the base cover.
49
Removing the I/O board
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Prerequisites
1 Remove the base cover.
2 Remove the battery.
Procedure
1 Remove the two screws (M1.6x3) that secure the I/O board to the palm-rest
assembly.
2 Peel o the tape that secures the display cable to the I/O board.
3 Disconnect the media-card reader cable from the I/O board.
4 Open the latch and disconnect the I/O-board cable from the I/O board.
50
5 Open the latch and disconnect the ngerprint-reader cable (optional) from the
I/O board.
Figure 16. Removing the I/O board
1screws (2) 2 tape
3 display cable 4 latch
5 I/O-board cable 6 ngerprint-reader cable
(optional)
7 latch 8 media-card reader cable
6 Peel o the tape that secures the I/O board.
51
7 Starting from the outer edge, lift the I/O board at an angle and remove the I/O
board.
Figure 17. Removing the I/O board
1 palm-rest assembly 2 I/O board
52
Replacing the I/O board
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
1 Slide the I/O board at an angle and then align the screw holes on the I/O board
with the screw holes on the palm-rest assembly.
2 Adhere the tape that secures the I/O board.
3 Align the screw hole on the display cable with the screw hole on the I/O board.
4 Replace the two screws (M1.6x3) that secure the I/O board to the palm-rest
assembly.
5 Slide the I/O-board cable into the I/O board and close the latch to secure the
cable.
6 Slide the ngerprint-reader cable (optional) into the I/O board and close the
latch to secure the cable.
7 Connect the media-card reader cable to the connector on the I/O board.
8 Adhere the tape that secures the display cable to the I/O board.
Post-requisites
1 Replace the battery.
2 Replace the base cover.
53
Removing the display assembly
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Prerequisites
1 Remove the base cover.
2 Remove the battery.
Procedure
1 Disconnect the touchscreen cable (optional) and camera cable from the system
board.
2 Peel o the tape that secures the antenna cables to the system board.
3 Remove the screw (M2x3) that secures the wireless-card bracket to the system
board.
4 Lift the wireless-card bracket o the wireless card.
54
5 Disconnect the antenna cables from the wireless card.
Figure 18. Removing the display assembly
1touchscreen cable (optional) 2 camera cable
3 wireless-card bracket 4 screw
5 antenna cables (2) 6 wireless card
7 tape
6 Remove the screw (M1.6x3) that secures the display cable to the I/O board.
7 Peel o the tapes that secure the display cable to the fan and the I/O board.
8 Disconnect the media-card reader cable from the I/O board.
55
9 Note the display-cable routing and remove the cable from the routing guides on
the fan.
10 Peel o the tape from the display-cable bracket.
Figure 19. Removing the display assembly
1tapes (4) 2 screw
3 media-card reader cable 4 display cable
5 routing guides (2)
11 Remove the two screws (M2x3) that secure the display-cable bracket to the
system board.
12 Lift the display-cable bracket o the display cable.
56
13 Using the pull tab, disconnect the display cable from the system board.
Figure 20. Removing the display assembly
1 display cable 2 display-cable bracket
3 screws (2) 4 pull tab
57
14 Open the palm-rest assembly at an angle of 90 degrees, and then remove the
four screws (M2.5x4) that secure the display hinges to the palm-rest assembly.
Figure 21. Removing the display assembly
1palm-rest assembly 2 display assembly
3 display hinges (2) 4 screws (4)
58
15 Slide and remove the palm-rest assembly from the display hinges.
Figure 22. Removing the display assembly
1 palm-rest assembly 2 display assembly
59
Replacing the display assembly
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
1 Slide the palm-rest assembly under the display hinges and align the screw holes
on the palm-rest assembly with the screw holes on the display hinges.
2 Replace the four screws (M2.5x4) that secure the palm-rest assembly to the
display hinges.
3 Close the palm-rest assembly.
4 Connect the display cable to the system board.
5 Align the screw holes on the display-cable bracket with the screw holes on the
system board.
6 Replace the two screws (M2x3) that secure the display-cable bracket to system
board.
7 Adhere the tape over the display-cable bracket.
8 Route the display cable through the routing guides on the fan.
9 Connect the media-card reader cable to the I/O board.
10 Adhere the tape that secures the display cable to the fan and the I/O board.
11 Replace the screw (M1.6x3) that secures the display cable to the I/O board.
12 Connect the antenna cables to the wireless card.
13 Align the screw hole on the wireless-card bracket with the screw hole on the
system board.
14 Replace the screw (M2x3) that secures the wireless-card bracket to the system
board.
15 Adhere the tape that secures the antenna cables to the system board.
16 Connect the touchscreen cable (optional) and camera cable to the system board.
60
Removing the display hinge cover
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
NOTE: The display hinge cover is included as part of the display assembly.
However, the hinge cover can be replaced separately.
Prerequisites
1 Remove the base cover.
2 Remove the battery.
3 Remove the display assembly.
Procedure
1 With the display facing up, slide the display hinge cover towards the right.
62
2 Lift the display hinge cover o the display assembly.
Figure 23. Remove the display hinge cover
1 display hinge cover 2 display assembly
63
Replacing the display hinge cover
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
NOTE: The display hinge cover is included as part of the display assembly.
However, the hinge cover can be replaced separately.
Procedure
1 Align the display hinge cover to the base of the display assembly.
2 With the display facing up, press and slide the display hinge cover to the left, to
lock it into position.
Post-requisites
1 Replace the display assembly.
2 Replace the battery.
3 Replace the base cover.
64
Removing the antenna
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
NOTE: The antenna is included as part of the display assembly. However,
the antenna can be replaced separately.
Prerequisites
1 Remove the base cover.
2 Remove the battery.
3 Remove the display assembly.
4 Remove the display hinge cover.
Procedure
1 Remove the four screws (M2x4) that secure the antenna to the display
assembly.
65
2 Lift the antenna o the display assembly.
Figure 24. Removing the antenna
1 antenna 2 screws (4)
66
Replacing the antenna
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
NOTE: The antenna is included as part of the display assembly. However,
the antenna can be replaced separately.
Procedure
1 Align the screw holes on the antenna with the screw holes on the display
assembly.
2 Replace the four screws (M2x4) that secure the antenna to the display
assembly.
Post-requisites
1 Replace the display hinge cover.
2 Replace the display assembly.
3 Replace the battery.
4 Replace the base cover.
67
Removing the system board
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
NOTE: Your computer’s Service Tag is stored in the system board. You must
enter the Service Tag in the BIOS setup program after you replace the
system board.
NOTE: Replacing the system board removes any changes you have made to
the BIOS using the BIOS setup program. You must make the appropriate
changes again after you replace the system board.
NOTE: Before disconnecting the cables from the system board, note the
location of the connectors so that you can reconnect the cables correctly
after you replace the system board.
Prerequisites
1 Remove the base cover.
2 Remove the battery.
3 Remove the wireless card.
4 Remove the solid-state drive.
5 Remove the heat sink.
Procedure
1 Peel o the tape that secures the antenna cables and power-adapter port cable
to the system board.
2 Disconnect the camera cable, touchscreen cable (optional), power-adapter port
cable, and coin-cell battery cable from the system board.
68
3 Open the latch and disconnect the keyboard-controls board cable from the
system board.
Figure 25. Removing the system board
1touchscreen cable (optional) 2 camera cable
3 tape 4 power-adapter port cable
5 coin-cell battery cable 6 speaker cable
7 keyboard-controls board cable 8 latch
4 Peel o the tape from the display-cable bracket.
69
5 Peel o the tape that secures the speaker cable to the system board.
6 Disconnect the fan cable from the system board.
7 Open the latches and disconnect the I/O-board cable and the touchpad cable
from the system board.
Figure 26. Removing the system board
1tape (3) 2 latches (2)
3 I/O-board cable 4 touchpad cable
5 fan cable
8 Remove the two screws (M2x3) that secure the display-cable bracket to the
system board.
9 Lift the display-cable bracket o the display cable.
70
10 Using the pull tab, disconnect the display cable from the system board.
Figure 27. Removing the system board
1display-cable bracket 2 screws (2)
3 display cable
11 Remove the six screws (M1.6x3) that secure the system board to the palm-rest
assembly.
71
12 Starting from the outer edge, lift the system board at an angle to release it from
the tabs on the palm-rest assembly.
Figure 28. Removing the system board
1screws (6) 2 system board
3 palm-rest assembly
72
Replacing the system board
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
NOTE: Your computer’s Service Tag is stored in the system board. You must
enter the Service Tag in the BIOS setup program after you replace the
system board.
NOTE: Replacing the system board removes any changes you have made to
the BIOS using the BIOS setup program. You must make the appropriate
changes again after you replace the system board.
Procedure
1 Using the alignment posts, place the system on the palm-rest assembly and align
the screw holes on the system board with the screw holes on the palm-rest
assembly.
2 Replace the six screws (M1.6x3) that secure the system board to the palm-rest
assembly.
3 Slide the I/O-board cable, the touchpad cable, and the keyboard-controls board
cable into the system board and close the connector latches to secure the
cables.
4 Connect the camera cable, the touchscreen cable (optional), the power-adapter
port cable, the coin-cell battery cable, the speaker cable, the fan cable, and the
display cable to the system board.
5 Adhere the tape that secures the antenna cables and power-adapter port to the
system board.
6 Align the screw holes on the display-cable bracket with the screw holes on the
system board.
7 Replace the two screws (M2x3) that secure the display-cable bracket to system
board.
8 Adhere the tapes that secure the speaker cable to the system board.
73
9 Adhere the tape over the display-cable bracket.
Post-requisites
1 Replace the heat sink.
2 Replace the solid-state drive.
3 Replace the wireless card.
4 Replace the battery.
5 Replace the base cover.
Entering the Service Tag in the BIOS setup
program
1 Turn on or restart your computer.
2 Press F2 when the Dell logo is displayed to enter the BIOS setup program.
3 Navigate to the Main tab and enter the Service Tag in the Service Tag Input
eld.
74
Removing the power-adapter
port
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Prerequisites
1 Remove the base cover.
2 Remove the battery.
3 Remove the wireless card.
4 Remove the system board.
Procedure
1 Remove the screw (M2x3) that secures the power-adapter port to the palm-rest
assembly.
2 Note the power-adapter port cable routing and remove the cable from the
routing guide on the palm-rest assembly.
75
3 Lift the power-adapter port o the palm-rest assembly.
Figure 29. Removing the power-adapter port
1 screw 2 power-adapter port cable
3 palm-rest assembly 4 power-adapter port
76
Replacing the power-adapter
port
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
1 Align the screw hole on the power-adapter port with the screw hole on the
palm-rest assembly.
2 Replace the screw (M2x3) that secures the power-adapter port to the palm-rest
assembly.
3 Route the power-adapter port cable through the routing guide on the palm-rest
assembly.
Post-requisites
1 Replace the system board.
2 Replace the wireless card.
3 Replace the battery.
4 Replace the base cover.
77
Removing the fan
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Prerequisites
1 Remove the base cover.
2 Remove the battery.
3 Remove the wireless card.
4 Remove the system board.
Procedure
1 Peel o the tape that secures the display cable to the fan.
78
2 Note the display-cable routing and remove the cable from the routing guides on
the fan.
Figure 30. Removing the fan
1tape (3) 2 display cable
3 routing guides (2)
3 Remove the screw (M1.6x3) that secures the fan to the palm-rest assembly.
79
4 Lift the fan along with its cable o the palm-rest assembly.
Figure 31. Removing the fan
1 screw 2 fan
3 palm-rest assembly
80
Replacing the fan
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
1 Align the screw holes on the fan with the screw holes on the palm-rest assembly.
2 Replace the screw (M1.6x3) that secures the fan to the palm-rest assembly.
3 Route the display cable through the routing guides on the fan.
4 Adhere the tape that secures the display cable to the fan.
Post-requisites
1 Replace the system board.
2 Replace the wireless card.
3 Replace the battery.
4 Replace the base cover.
81
Removing the keyboard
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Prerequisites
1 Remove the base cover.
2 Remove the battery.
3 Remove the wireless card.
4 Remove the speakers.
5 Remove the coin-cell battery.
6 Remove the heat sink.
7 Remove the I/O board.
8 Remove the system board.
9 Remove the fan.
10 Remove the I/O-board cable.
82
Procedure
1 Open the latches and disconnect the keyboard cable and the keyboard-backlight
cable from the keyboard-controls board.
Figure 32. Removing the keyboard
1keyboard-backlight cable 2 latches (2)
3 keyboard cable 4 keyboard-controls board
2 Note the routing of the touchpad cable, the I/O-board cable, and the keyboard-
controls board cable, and peel o the cables from the keyboard.
83
3 Remove the 30 screws (M1.6x1.5) that secure the keyboard to the palm-rest
assembly.
Figure 33. Removing the keyboard
1screws (30) 2 keyboard
3 palm-rest assembly
84
4 Lift the keyboard o the palm-rest assembly.
Figure 34. Removing the keyboard
1 keyboard 2 palm-rest assembly
85
Replacing the keyboard
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
1 Align the screw holes on the keyboard with the screw holes on the palm-rest
assembly.
2 Replace the 30 screws (M1.6x1.5) that secure the keyboard to the palm-rest
assembly.
3 Adhere the touchpad cable, the I/O-board cable, and the keyboard-controls
board cable to the keyboard.
4 Slide the keyboard cable and the keyboard-backlight cable into the keyboard-
controls board and close the latches to secure the cables.
Post-requisites
1 Replace the I/O-board cable.
2 Replace the fan.
3 Follow the procedure from step 1 to step 8 in "Replacing the system board".
4 Replace the I/O board.
5 Replace the heat sink.
6 Replace the coin-cell battery.
7 Replace the speakers.
8 Replace the wireless card.
9 Replace the battery.
10 Replace the base cover.
86
Removing the palm-rest
assembly
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Prerequisites
1 Remove the base cover.
2 Remove the battery.
3 Remove the wireless card.
4 Remove the speakers.
5 Remove the coin-cell battery.
6 Remove the battery-status light cable.
7 Remove the touchpad.
8 Remove the I/O-board cable.
9 Remove the I/O board.
10 Remove the display assembly.
11 Remove the heat sink.
12 Remove the system board.
13 Remove the fan.
14 Remove the keyboard.
87
Procedure
After performing all the pre-requisites, we are left with the palm rest.
88
Replacing the palm-rest
assembly
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
Place the palm rest face down on a clean and at surface.
Post-requisites
1 Replace the keyboard.
2 Replace the fan.
89
3 Replace the system board.
4 Replace the heat sink.
5 Replace the display assembly.
6 Replace the I/O board.
7 Replace the I/O-board cable.
8 Replace the touchpad.
9 Replace the battery-status light cable.
10 Replace the coin-cell battery.
11 Replace the speakers.
12 Replace the wireless card.
13 Replace the battery.
14 Replace the base cover.
90
Downloading drivers
Downloading the audio driver
1 Turn on your computer.
2 Go to www.dell.com/support.
3 Click Product Support, enter the Service Tag of your computer, and then click
Submit.
NOTE: If you do not have the Service Tag, use the auto-detect feature
or manually browse for your computer model.
4 Click Drivers & Downloads → Find it myself.
5 Scroll down the page and expand Audio.
6 Click Download to download the audio driver for your computer.
7 After the download is complete, navigate to the folder where you saved the
audio driver le.
8 Double-click the audio driver le icon and follow the instructions on the screen to
install the driver.
Downloading the graphics driver
1 Turn on your computer.
2 Go to www.dell.com/support.
3 Click Product Support, enter the Service Tag of your computer, and then click
Submit.
NOTE: If you do not have the Service Tag, use the auto-detect feature
or manually browse for your computer model.
4 Click Drivers & downloads → Find it myself.
5 Scroll down the page and expand Video.
6 Click Download to download the graphics driver for your computer.
7 After the download is complete, navigate to the folder where you saved the
graphics driver le.
8 Double-click the graphics driver le icon and follow the instructions on the
screen to install the driver.
91
Downloading the USB 3.0 driver
1 Turn on your computer.
2 Go to www.dell.com/support.
3 Click Product Support, enter the Service Tag of your computer, and then click
Submit.
NOTE: If you do not have the Service Tag, use the auto-detect feature
or manually browse for your computer model.
4 Click Drivers & Downloads → Find it myself.
5 Scroll down the page and expand Chipset.
6 Click Download to download the USB 3.0 driver for your computer.
7 After the download is complete, navigate to the folder where you saved USB 3.0
driver le.
8 Double-click the USB 3.0 driver le icon and follow the instructions on screen to
install the driver.
Downloading the Wi-Fi driver
1 Turn on the computer.
2 Go to www.dell.com/support.
3 Click Product support, enter the Service Tag of your computer, and then click
Submit.
NOTE: If you do not have the Service Tag, use the auto-detect feature
or manually browse for your computer model.
4 Click Drivers & downloads → Find it myself.
5 Scroll down the page and expand Network.
6 Click Download to download the Wi-Fi driver for your computer.
7 After the download is complete, navigate to the folder where you saved the Wi-
Fi driver le.
8 Double-click the driver le icon and follow the instructions on the screen.
Downloading the media-card reader driver
1 Turn on your computer.
92
2 Go to www.dell.com/support.
3 Click Product support, enter the Service Tag of your computer, and then click
Submit.
NOTE: If you do not have the Service Tag, use the auto-detect feature
or manually browse for your computer model.
4 Click Drivers & downloads → Find it myself.
5 Scroll down the page and expand Chipset.
6 Click Download to download the media-card reader driver for your computer.
7 After the download is complete, navigate to the folder where you saved the card
reader driver le.
8 Double-click the card reader driver le icon and follow the instructions on the
screen.
Downloading the chipset driver
1 Turn on your computer.
2 Go to www.dell.com/support.
3 Click Product Support, enter the Service Tag of your computer, and then click
Submit.
NOTE: If you do not have the Service Tag, use the auto-detect feature
or manually browse for your computer model.
4 Click Drivers & downloads → Find it myself.
5 Scroll down the page and expand Chipset.
6 Click Download to download the appropriate chipset driver for your computer.
7 After the download is complete, navigate to the folder where you saved the
chipset driver le.
8 Double-click the chipset driver le icon and follow the instructions on the screen
to install the driver.
Downloading the network driver
1 Turn on your computer.
2 Go to www.dell.com/support.
93
3 Click Product support enter the Service Tag of your computer and click Submit.
NOTE: If you do not have the Service Tag, use the auto-detect feature
or manually browse for your computer model.
4 Click Drivers & downloads → Find it myself.
5 Scroll down the page and expand Network.
6 Click Download to download the network driver for your computer.
7 Save the le, and after the download is complete, navigate to the folder where
you saved the network driver le.
8 Double-click the network driver le icon and follow the instructions on screen.
94
System setup
NOTE: Depending on the computer and its installed devices, the items listed
in this section may or may not be displayed.
Boot Sequence
Boot Sequence allows you to bypass the System Setup–dened boot device order
and boot directly to a specic device (for example: optical drive or hard drive). During
the Power-on Self Test (POST), when the Dell logo appears. you can:
• Access System Setup by pressing F2 key
• Bring up the one-time boot menu by pressing F12 key
The one-time boot menu displays the devices that you can boot from including the
diagnostic option. The boot menu options are:
• Removable Drive (if available)
• STXXXX Drive
NOTE: XXX denotes the SATA drive number.
• Optical Drive (if available)
• Diagnostics
NOTE: Choosing Diagnostics, will display the ePSA diagnostics screen.
The boot sequence screen also displays the option to access the System Setup
screen.
Navigation keys
NOTE: For most of the System Setup options, changes that you make are
recorded but do not take eect until you restart the system.
Keys Navigation
Up arrow Moves to the previous eld.
95
Keys Navigation
Down arrow Moves to the next eld.
Enter Selects a value in the selected eld (if applicable) or follow
the link in the eld.
Spacebar Expands or collapses a drop‐down list, if applicable.
Tab Moves to the next focus area.
NOTE: For the standard graphics browser only.
Esc Moves to the previous page until you view the main screen.
Pressing Esc in the main screen displays a message that
prompts you to save any unsaved changes and restarts the
system.
BIOS overview
CAUTION: Unless you are an expert computer user, do not change the
settings in the BIOS Setup program. Certain changes can make your
computer work incorrectly.
NOTE: Before you change BIOS Setup program, it is recommended that you
write down the BIOS Setup program screen information for future
reference.
Use the BIOS Setup program for the following purposes:
• Get information about the hardware installed in your computer, such as the
amount of RAM and the size of the hard drive.
• Change the system conguration information.
• Set or change a user-selectable option, such as the user password, type of hard
drive installed, and enabling or disabling base devices.
Entering BIOS setup program
1 Turn on (or restart) your computer.
96
2 During POST, when the DELL logo is displayed, watch for the F2 prompt to
appear, and then press F2 immediately.
NOTE: The F2 prompt indicates that the keyboard is initialized. This
prompt can appear very quickly, so you must watch for it, and then
press F2. If you press F2 before the F2 prompt, this keystroke is lost. If
you wait too long and the operating system logo appears, continue to
wait until you see the desktop. Then, turn o your computer and try
again.
System setup options
NOTE: Depending on this computer and its installed devices, the items listed
in this section may or may not appear.
Table 3. System setup options—System information menu
General-System Information
System Information
BIOS Version Displays the BIOS version number.
Service Tag Displays the Service Tag of the computer.
Asset Tag Displays the Asset Tag of the computer.
Ownership Tag Displays the ownership tag of the computer.
Manufacture Date Displays the manufacture date of the computer.
Ownership Date Displays the ownership date of the computer.
Express Service Code Displays the express service code of the computer.
Memory Information
Memory Installed Displays the total computer memory installed.
Memory Available Displays the total computer memory available.
Memory Speed Displays the memory speed.
Memory Channel Mode Displays single or dual channel mode.
Memory Technology Displays the technology used for the memory.
DIMM A Size Displays the DIMM A memory size.
DIMM B Size Displays the DIMM B memory size.
97
General-System Information
Processor Information
Processor Type Displays the processor type.
Core Count Displays the number of cores on the processor.
Processor ID Displays the processor identication code.
Current Clock Speed Displays the current processor clock speed.
Minimum Clock Speed Displays the minimum processor clock speed.
Maximum Clock Speed Displays the maximum processor clock speed.
Processor L2 Cache Displays the processor L2 Cache size.
Processor L3 Cache Displays the processor L3 Cache size.
HT Capable Displays whether the processor is HyperThreading
(HT) capable.
64-Bit Technology Displays whether 64-bit technology is used.
Device Information
SATA-0 Displays the SATA-0 device information of the
computer.
SATA-2 Displays the SATA-2 device information of the
computer.
M.2 PCIe SSD-0 Displays the M.2 PCIe SSD information of the
computer.
Video Controller Displays the video controller type of the computer.
dGPU Video Controller Displays the discrete graphics information of the
computer.
Video BIOS Version Displays the video BIOS version of the computer.
Video Memory Displays the video memory information of the
computer.
Panel Type Displays the Panel Type of the computer.
Native Resolution Displays the native resolution of the computer.
Audio Controller Displays the audio controller information of the
computer.
98
General-System Information
Wi-Fi Device Displays the wireless device information of the
computer.
Bluetooth Device Displays the bluetooth device information of the
computer.
Battery Information Displays the battery health information.
Boot Sequence
Boot Sequence Displays the boot sequence.
Boot List Option Displays the available boot options.
Advanced Boot Options
Enable Legacy Option
ROMs
Enable or disable the Legacy Option ROMs.
Enable UEFI Network
Stack
Enable or disable UEFI Network Stack.
UEFI Boot Path Security Enable or disable the system to prompt the user to
enter the Admin password when booting a UEFI
boot path from the F12 boot menu.
Date/Time Displays the current date in MM/DD/YY format and
current time in HH:MM:SS AM/PM format.
Table 4. System setup options—System Conguration menu
System Conguration
SATA Operation Congure operating mode of the integrated SATA
hard drive controller.
Drives Enable or disable various drives on board.
SMART Reporting Enable or disable SMART Reporting during system
startup.
USB Conguration
Enable Boot Support Enable or disable booting from USB mass storage
devices such as external hard drive, optical drive,
and USB drive.
99
System Conguration
Enable External USB Port Enable or disable booting from USB mass storage
devices connected to external USB port.
USB PowerShare Enable or disable charging external devices through
the USB PowerShare port.
Audio Enable or disable the integrated audio controller.
Keyboard Illumination Congure the operating mode of the keyboard
illumination feature.
Keyboard Backlight with
AC
Enable or disable the keyboard backlight.
Miscellaneous Devices Enable or disable various onboard devices.
Enable Camera Enable or disable the camera.
Enable Secure Digital (SD)
Card
Enable or disable the SD card.
Table 5. System setup options—Video menu
Video
LCD Brightness Set the panel brightness independently for Battery
and AC power.
Table 6. System setup options—Security menu
Security
Strong Password Enable or disable strong passwords.
Password Conguration Control the minimum and maximum number of
characters allowed for Admin and System
passwords.
Password Bypass Bypass the System (Boot) Password and the
internal HDD password prompts during a system
restart.
Password Change Enable or disable changes to the System and Hard
Disk passwords when an administrator password is
set.
100
Security
Non-Admin Setup Changes Determines whether changes to the setup option
are permitted when an administrator password is
set.
UEFI Capsule Firmware
Updates
Enable or disable BIOS updates through UEFI
capsule update packages.
PTT Security Enable or disable Platform Trust Technology (PTT)
visibility to the operating system.
Computrace(R) Enable or disable the BIOS module interface of the
optional Computrace(R) Service from Absolute
Software.
CPU XD Support Enable or disable the Execute Disable mode of the
Processor.
Admin Setup Lockout Enable to prevent users from entering Setup when
an Admin Password is set.
Table 7. System setup options—Secure Boot menu
Secure Boot
Secure Boot Enable Enable or disable the secure boot feature.
Expert Key Management
Expert Key Management Enable or disable Expert Key Management.
Custom Mode Key
Management
Select the custom values for expert key
management.
Table 8. System setup options—Intel Software Guard Extensions menu
Intel Software Guard Extensions
Intel SGX Enable Enable or disable Intel Software Guard Extensions.
Enclave Memory Size Set the Intel Software Guard Extensions Enclave
Reserve Memory Size.
Performance
Multi Core Support Enable multiple cores.
Default: Enabled.
101
Intel Software Guard Extensions
Intel SpeedStep Enable or disable Intel Speedstep Technology.
Default: Enabled.
NOTE: If enabled, the processor clock speed
and core voltage are adjusted dynamically
based on the processor load.
C-States Control Enable or disable additional processor sleep states.
Default: Enabled.
Intel TurboBoost Enable or disable Intel TurboBoost mode of the
processor.
Default: Enabled.
HyperThread control Enable or disable HyperThreading in the processor.
Default: Enabled.
Power Management
AC Behavior Enables the system to turn on automatically, when
AC is inserted.
Enable Intel Speed Shift
Technology
Enable or disable Intel Speed Shift Technology.
Auto on Time Enable to set the computer to turn on automatically
every day or on a preselected date and time. This
option can be congured only if the Auto On Time is
set to Everyday, Weekdays or Selected Days.
Default: Disabled.
USB Wake Support Enable the USB devices to wake the computer from
Standby.
Advanced Battery Charge
Conguration
Enable Advanced Battery Charge Conguration
from the beginning of the day to a specied work
period.
Primary Battery Charge
Conguration
Set the primary battery charge settings with a
preselected custom charge start and stop.
Default: Adaptive.
POST Behavior
Adapter Warnings Enable adapter warnings.
102
Intel Software Guard Extensions
Default: Enabled.
Numlock Enable Enable or disable Numlock.
Default: Enable Numlock.
Fn Lock Options Enable or disable the Fn lock mode.
Fastboot Enable to set the speed of the boot process.
Default: Thorough.
Extend BIOS POST Time Congure additional pre-boot delay.
Pull Screen Logo Enable or disable to display full screen logo.
Warnings and Errors Select an action on encountering a warning or error.
Table 9. System setup options—Virtualization Support menu
Virtualization Support
Virtualization Specify whether a Virtual Machine Monitor (VMM)
can utilize the additional hardware capabilities
provided by Intel Virtualization Technology.
VT for Direct I/O Specify whether a Virtual Machine Monitor (VMM)
can utilize the additional hardware capabilities
provided by Intel Virtualization Technology for Direct
I/O.
Table 10. System setup options—Wireless menu
Wireless
Wireless Switch Determine which wireless devices can be controlled
by the Wireless Switch.
Wireless Device Enable Enable or disable internal wireless devices.
Table 11. System setup options—Maintenance menu
Maintenance
Service Tag Display the system’s Service Tag.
Asset Tag Create a system Asset Tag.
103
Maintenance
BIOS Downgrade Control ashing of the system rmware to previous
revisions.
Data Wipe Enable to securely erase data from all internal
storage devices.
BIOS Recovery Enable the user to recover from certain corrupted
BIOS conditions from a recovery le on the user
primary hard drive or an external USB key.
Table 12. System setup options—System Logs menu
System Logs
BIOS Events Display BIOS events.
Thermal Events Display Thermal events.
Power Events Display Power events.
Table 13. System setup options—SupportAssist System Resolution menu
SupportAssist System Resolution
Auto OS Recovery
Threshold
Control the automatic boot ow for SupportAssist
System Resolution Console and for Dell OS
Recovery tool.
SupportAssist OS Recovery Enable or disable the boot ow for SupportAssist
OS Recovery tool in the even of certain system
errors.
System and setup password
You can create a system password and a setup password to secure your computer.
Password type Description
System password Password that you must enter to log on to your system.
Setup password Password that you must enter to access and make changes
to the BIOS settings of your computer.
CAUTION: The password features provide a basic level of security for the
data on your computer.
104
CAUTION: Anyone can access the data stored on your computer if it is not
locked and left unattended.
NOTE: Your computer is shipped with the system and setup password
feature is disabled.
Assigning a system password and setup password
You can assign a new System Password only when the status is in Not Set.
To enter the system setup, press F2 immediately after a power-on or re-boot.
1 In the System BIOS or System Setup screen, select Security and press Enter.
The Security screen is displayed.
2 Select System Password and create a password in the Enter the new password
eld.
Use the following guidelines to assign the system password:
– A password can have up to 32 characters.
– The password can contain the numbers 0 through 9.
– Only lower case letters are valid, upper case letters are not allowed.
– Only the following special characters are allowed: space, (”), (+), (,), (-), (.),
(/), (;), ([), (\), (]), (`).
3 Type the system password that you entered earlier in the Conrm new
password eld and click OK.
4 Press Esc and a message prompts you to save the changes.
5 Press Y to save the changes.
The computer reboots.
Deleting or changing an existing system and/or setup
password
Ensure that the Password Status is Unlocked (in the System Setup) before
attempting to delete or change the existing System and/or Setup password. You
cannot delete or change an existing System or Setup password, if the Password
Status is Locked.
To enter the System Setup, press F2 immediately after a power-on or reboot.
1 In the System BIOS or System Setup screen, select System Security and press
Enter.
The System Security screen is displayed.
105
2 In the System Security screen, verify that Password Status is Unlocked.
3 Select System Password, alter or delete the existing system password and press
Enter or Tab.
4 Select Setup Password, alter or delete the existing setup password and press
Enter or Tab.
NOTE: If you change the System and/or Setup password, re-enter the
new password when promoted. If you delete the System and/or Setup
password, conrm the deletion when promoted.
5 Press Esc and a message prompts you to save the changes.
6 Press Y to save the changes and exit from System Setup.
The computer reboots.
Clearing CMOS settings
1 Remove the base cover.
2 Remove the battery.
3 Remove the coin-cell battery.
4 Wait for one minute.
5 Replace the coin-cell battery.
6 Replace the battery.
7 Replace the base cover.
Clearing forgotten passwords
Contact Dell technical support to clear the forgotten passwords, see www.dell.com/
contactdell.
106
Troubleshooting
Flashing the BIOS
You may need to ash (update) the BIOS when an update is available or when you
replace the system board.
Follow these steps to ash the BIOS:
1 Turn on your computer.
2 Go to www.dell.com/support.
3 Click Product support, enter the Service Tag of your computer, and then click
Submit.
NOTE: If you do not have the Service Tag, use the auto-detect feature
or manually browse for your computer model.
4 Click Drivers & downloads → Find it myself.
5 Select the operating system installed on your computer.
6 Scroll down the page and expand BIOS.
7 Click Download to download the latest version of the BIOS for your computer.
8 After the download is complete, navigate to the folder where you saved the BIOS
update le.
9 Double-click the BIOS update le icon and follow the instructions on the screen.
Flashing BIOS (USB key)
1 Follow the procedure from step 1 to step 7 in "Flashing the BIOS" to download
the latest BIOS setup program le.
2 Create a bootable USB drive. For more information see the knowledge base
article SLN143196 at www.dell.com/support.
3 Copy the BIOS setup program le to the bootable USB drive.
4 Connect the bootable USB drive to the computer that needs the BIOS update.
5 Restart the computer and press F12 when the Dell logo is displayed on the
screen.
6 Boot to the USB drive from the One Time Boot Menu.
7 Type the BIOS setup program lename and press Enter.
107
8 The BIOS Update Utility appears. Follow the instructions on the screen to
complete the BIOS update.
Enhanced Pre-Boot System Assessment
(ePSA) diagnostics
The ePSA diagnostics (also known as system diagnostics) performs a complete check
of your hardware. The ePSA is embedded with the BIOS and is launched by the BIOS
internally. The embedded system diagnostics provides a set of options for particular
devices or device groups allowing you to:
• Run tests automatically or in an interactive mode
• Repeat tests
• Display or save test results
• Run thorough tests to introduce additional test options to provide extra
information about the failed device(s)
• View status messages that inform you if tests are completed successfully
• View error messages that inform you of problems encountered during testing
CAUTION: Use the system diagnostics to test only your computer. Using
this program with other computers may cause invalid results or error
messages.
NOTE: Some tests for specic devices require user interaction. Always
ensure that you are present at the computer terminal when the diagnostic
tests are performed.
For more information, see Dell EPSA Diagnostic 3.0.
Running the ePSA diagnostics
1 Power-on the computer.
2 As the computer boots, press the F12 key as the Dell logo appears.
3 On the boot menu screen, select the Diagnostics option.
4 Click the arrow key at the bottom left corner.
Diagnostics front page is displayed.
5 Press the arrow in the lower-right corner to go to the page listing.
The items detected are listed.
6 To run a diagnostic test on a specic device, press Esc and click Yes to stop the
diagnostic test.
108
7 Select the device from the left pane and click Run Tests.
8 If there are any issues, error codes are displayed.
Note the error code and validation number and contact Dell.
System diagnostic lights
Power and battery-status light/hard-drive activity light
Indicates the battery-charge status or the hard-drive activity.
NOTE: Press Fn+H to toggle this light between power and battery-status
light and hard-drive activity light.
Hard-drive activity light
Turns on when the computer reads from or writes to the hard drive.
Power and battery-status light
Indicates the power and battery-charge status.
Solid white — Power adapter is connected and the battery has more than 5 percent
charge.
Amber — Computer is running on battery and the battery has less than 5 percent
charge.
O
• Power adapter is connected and the battery is fully charged.
• Computer is running on battery and the battery has more than 5 percent charge.
• Computer is in sleep state, hibernation, or turned o.
The power and battery-status light blinks amber along with beep codes indicating
failures.
For example, the power and battery-status light blinks amber two times followed by a
pause, and then blinks white three times followed by a pause. This 2,3 pattern
continues until the computer is turned o indicating no memory or RAM is detected.
The following table shows dierent power and battery-status light patterns and
associated problems.
109
Table 14. Diagnostics
Light pattern Problem description
2,1 CPU failure
2,2 System board: BIOS and ROM failure
2,3 No memory or RAM detected
2,4 Memory or RAM failure
2,5 Invalid memory installed
2,6 System board or chipset error
2,7 LCD failure
3,1 CMOS battery failure
3,2 PCI or video card or chip failure
3,3 Recovery image not found
3,4 Recovery image found but invalid
Camera status light: Indicates whether the camera is in use.
• Solid white — Camera is in use.
•O — Camera is not in use.
Caps Lock status light: Indicates whether Caps Lock is enabled or disabled.
• Solid white — Caps Lock enabled.
•O — Caps Lock disabled.
Flea power release
Flea power is the residual static electricity that remains on the computer even after it
has been powered o and the battery has been removed. The following procedure
provides the instructions on how to conduct ea power release:
1 Turn o your computer.
2 Remove the base cover.
3 Follow step 1 in "Removing the battery".
4 Press and hold the power button for 15 seconds to drain the ea power.
110
5 Follow step 4 in "Replacing the battery".
6 Replace the base cover.
7 Turn on your computer.
Wi-Fi power cycle
If your computer is unable to access the internet due to Wi-Fi connectivity issues a
Wi-Fi power cycle procedure may be performed. The following procedure provides the
instructions on how to conduct a Wi-Fi power cycle:
1 Turn o your computer.
2 Turn o the modem.
3 Turn o the wireless router.
4 Wait for 30 seconds.
5 Turn on the wireless router.
6 Turn on the modem.
7 Turn on your computer.
111
Getting help and contacting Dell
Self-help resources
You can get information and help on Dell products and services using these self-help
resources:
Table 15. Self-help resources
Information about Dell products and
services
www.dell.com
Dell Help & Support app
Accessing help In Windows search, type Help and
Support, and press Enter.
Online help for operating system www.dell.com/support/windows
www.dell.com/support/linux
Troubleshooting information, user
manuals, setup instructions, product
specications, technical help blogs,
drivers, software updates, and so on.
www.dell.com/support
Dell knowledge base articles for a variety
of computer concerns. 1 Go to www.dell.com/support.
2 Type the subject or keyword in the
Search box.
3 Click Search to retrieve the related
articles.
Learn and know the following information
about your product:
• Product specications
• Operating system
• Setting up and using your product
• Data backup
• Troubleshooting and diagnostics
See Me and My Dell at www.dell.com/
support/manuals.
To locate the Me and My Dell relevant to
your product, identify your product
through one of the following:
• Select Detect Product.
112
• Factory and system restore
• BIOS information
• Locate your product through the
drop-down menu under View
Products.
• Enter the Service Tag number or
Product ID in the search bar.
Contacting Dell
To contact Dell for sales, technical support, or customer service issues, see
www.dell.com/contactdell.
NOTE: Availability varies by country and product, and some services may
not be available in your country.
NOTE: If you do not have an active internet connection, you can nd
contact information on your purchase invoice, packing slip, bill, or Dell
product catalog.
113