DELL 9510 2in1 User Manual

Displayed below is the user manual for 9510 2in1 by DELL which is a product in the Notebooks category. This manual has pages.

Related Manuals

DELL 9510 2in1 Manual

DELL 9410 2in1 Manual

Latitude 9510

Service Manual

Regulatory Model: P94F/P95F

Regulatory Type: P94F001/P95F001

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your product.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the

problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

subsidiaries. Other trademarks may be trademarks of their respective owners.

Rev. A00

1 Working on your computer............................................................................................................ 5

Safety instructions................................................................................................................................................................ 5

Before working inside your computer........................................................................................................................... 5

Safety precautions...........................................................................................................................................................6

Electrostatic discharge—ESD protection.................................................................................................................... 6

ESD field service kit ........................................................................................................................................................ 7

After working inside your computer.............................................................................................................................. 7

2 Major components of your system................................................................................................. 9

3 Removing and Installing Components........................................................................................... 10

Recommended tools............................................................................................................................................................ 10

Screw list...............................................................................................................................................................................10

Disassembly and reassembly...............................................................................................................................................12

SIM card tray.................................................................................................................................................................. 12

MicroSD card.................................................................................................................................................................. 13

Base cover.......................................................................................................................................................................15

Battery............................................................................................................................................................................. 18

WWAN card....................................................................................................................................................................23

Solid-state drive.............................................................................................................................................................25

Speakers..........................................................................................................................................................................27

System fan..................................................................................................................................................................... 30

I/O daughter board power cable................................................................................................................................. 32

I/O board........................................................................................................................................................................ 33

System board................................................................................................................................................................. 35

Display assembly............................................................................................................................................................ 42

Keyboard.........................................................................................................................................................................46

Power button with finger print reader (optional)......................................................................................................49

Power button..................................................................................................................................................................51

Smart card reader board.............................................................................................................................................. 52

Palmrest assembly.........................................................................................................................................................55

4 System setup.............................................................................................................................57

Entering BIOS without keyboard.......................................................................................................................................57

System setup options......................................................................................................................................................... 57

General screen options................................................................................................................................................. 57

System Configuration screen options.........................................................................................................................58

System Configuration screen options.........................................................................................................................59

Video screen options......................................................................................................................................................61

Security screen options................................................................................................................................................. 61

Secure Boot....................................................................................................................................................................62

Intel software Guard Extensions..................................................................................................................................63

Performance screen options........................................................................................................................................63

POST Behavior.............................................................................................................................................................. 64

Contents

Contents 3

Virtualization Support options......................................................................................................................................64

Wireless screen options................................................................................................................................................ 64

Maintenance...................................................................................................................................................................65

System logs screen options......................................................................................................................................... 65

System Log.......................................................................................................................................................................... 65

Updating the BIOS ............................................................................................................................................................. 65

Updating your system BIOS using a USB flash drive......................................................................................................66

System and setup password.............................................................................................................................................. 67

Assigning a system setup password............................................................................................................................67

Deleting or changing an existing system setup password........................................................................................68

5 Troubleshooting.........................................................................................................................69

Dell SupportAssist Pre-boot System Performance Check diagnostics........................................................................69

Running the SupportAssist Pre-Boot System Performance Check....................................................................... 69

System diagnostic lights.....................................................................................................................................................69

Flashing BIOS (USB key)....................................................................................................................................................70

Flashing the BIOS................................................................................................................................................................. 71

Backup media and recovery options.................................................................................................................................. 71

WiFi power cycle.................................................................................................................................................................. 71

Flea power release................................................................................................................................................................71

6 Getting help...............................................................................................................................73

Contacting Dell.....................................................................................................................................................................73

4Contents

Working on your computer

Safety instructions

Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless otherwise

noted, each procedure included in this document assumes that you have read the safety information that shipped with your computer.

NOTE: Before working inside your computer, read the safety information that is shipped with your computer. For more

safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance.

NOTE: Disconnect your computer from all power sources before opening the computer cover or panels. After you finish

working inside the computer, replace all covers, panels, and screws before connecting your computer to an electrical

outlet.

CAUTION: To avoid damaging the computer, ensure that the work surface is flat, dry and clean.

CAUTION: To avoid damaging the components and cards, handle them by their edges, and avoid touching the pins and

the contacts.

CAUTION: You should only perform troubleshooting and repairs as authorized or directed by the Dell technical

assistance team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. See the safety

instructions that is shipped with the product or at www.dell.com/regulatory_compliance.

CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface,

such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to

dissipate static electricity which could harm internal components.

CAUTION: When you disconnect a cable, pull it by its connector or its pull tab, not the cable itself. Some cables have

connectors with locking tabs or thumb-screws that you must disengage before disconnecting the cable. When

disconnecting cables, keep them evenly-aligned to avoid bending the connector pins. When connecting cables, ensure

that the ports and the connectors are correctly oriented and aligned.

CAUTION: Press and eject any installed card from the media-card reader.

NOTE: The color of your computer and certain components may appear differently than shown in this document.

Before working inside your computer

About this task

To avoid damaging your computer, perform the following steps before you begin working inside the computer.

Steps

1. Ensure that you follow the safety precautions.

2. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.

3. Turn off your computer.

4. Disconnect all network cables from the computer.

CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from

the network device.

5. Disconnect your computer and all attached devices from their electrical outlets.

6. Press and hold the power button while the computer is unplugged to ground the system board.

Working on your computer 5

NOTE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching

an unpainted metal surface at the same time as touching a connector on the back of the computer.

Safety precautions

The safety precautions chapter details the primary steps to be taken before performing any disassembly instructions.

Observe the following safety precautions before you perform any installation or break/fix procedures involving disassembly or reassembly:

• Turn off the system and all attached peripherals.

• Disconnect the system and all attached peripherals from AC power.

• Disconnect all network cables, telephone, and telecommunications lines from the system.

• Use an ESD field service kit when working inside any tabletnotebookdesktop to avoid electrostatic discharge (ESD) damage.

• After removing any system component, carefully place the removed component on an anti-static mat.

• Wear shoes with non-conductive rubber soles to reduce the chance of getting electrocuted.

Standby power

Dell products with standby power must be unplugged before you open the case. Systems that incorporate standby power are essentially

powered while turned off. The internal power enables the system to be remotely turned on (wake on LAN) and suspended into a sleep

mode and has other advanced power management features.

Unplugging, pressing and holding the power button for 15 seconds should discharge residual power in the system board. Remove the

battery from tablets.notebooks.

Bonding

Bonding is a method for connecting two or more grounding conductors to the same electrical potential. This is done through the use of a

field service electrostatic discharge (ESD) kit. When connecting a bonding wire, ensure that it is connected to bare metal and never to a

painted or non-metal surface. The wrist strap should be secure and in full contact with your skin, and ensure that you remove all jewelry

such as watches, bracelets, or rings prior to bonding yourself and the equipment.

Electrostatic discharge—ESD protection

ESD is a major concern when you handle electronic components, especially sensitive components such as expansion cards, processors,

memory DIMMs, and system boards. Very slight charges can damage circuits in ways that may not be obvious, such as intermittent

problems or a shortened product life span. As the industry pushes for lower power requirements and increased density, ESD protection is

an increasing concern.

Due to the increased density of semiconductors used in recent Dell products, the sensitivity to static damage is now higher than in

previous Dell products. For this reason, some previously approved methods of handling parts are no longer applicable.

Two recognized types of ESD damage are catastrophic and intermittent failures.

•Catastrophic – Catastrophic failures represent approximately 20 percent of ESD-related failures. The damage causes an immediate

and complete loss of device functionality. An example of catastrophic failure is a memory DIMM that has received a static shock and

immediately generates a "No POST/No Video" symptom with a beep code emitted for missing or nonfunctional memory.

•Intermittent – Intermittent failures represent approximately 80 percent of ESD-related failures. The high rate of intermittent failures

means that most of the time when damage occurs, it is not immediately recognizable. The DIMM receives a static shock, but the

tracing is merely weakened and does not immediately produce outward symptoms related to the damage. The weakened trace may

take weeks or months to melt, and in the meantime may cause degradation of memory integrity, intermittent memory errors, etc.

The more difficult type of damage to recognize and troubleshoot is the intermittent (also called latent or "walking wounded") failure.

Perform the following steps to prevent ESD damage:

• Use a wired ESD wrist strap that is properly grounded. The use of wireless anti-static straps is no longer allowed; they do not provide

adequate protection. Touching the chassis before handling parts does not ensure adequate ESD protection on parts with increased

sensitivity to ESD damage.

• Handle all static-sensitive components in a static-safe area. If possible, use anti-static floor pads and workbench pads.

• When unpacking a static-sensitive component from its shipping carton, do not remove the component from the anti-static packing

material until you are ready to install the component. Before unwrapping the anti-static packaging, ensure that you discharge static

electricity from your body.

• Before transporting a static-sensitive component, place it in an anti-static container or packaging.

6Working on your computer

ESD field service kit

The unmonitored Field Service kit is the most commonly used service kit. Each Field Service kit includes three main components: anti-

static mat, wrist strap, and bonding wire.

Components of an ESD field service kit

The components of an ESD field service kit are:

•Anti-Static Mat – The anti-static mat is dissipative and parts can be placed on it during service procedures. When using an anti-

static mat, your wrist strap should be snug and the bonding wire should be connected to the mat and to any bare metal on the system

being worked on. Once deployed properly, service parts can be removed from the ESD bag and placed directly on the mat. ESD-

sensitive items are safe in your hand, on the ESD mat, in the system, or inside a bag.

•Wrist Strap and Bonding Wire – The wrist strap and bonding wire can be either directly connected between your wrist and bare

metal on the hardware if the ESD mat is not required, or connected to the anti-static mat to protect hardware that is temporarily

placed on the mat. The physical connection of the wrist strap and bonding wire between your skin, the ESD mat, and the hardware is

known as bonding. Use only Field Service kits with a wrist strap, mat, and bonding wire. Never use wireless wrist straps. Always be

aware that the internal wires of a wrist strap are prone to damage from normal wear and tear, and must be checked regularly with a

wrist strap tester in order to avoid accidental ESD hardware damage. It is recommended to test the wrist strap and bonding wire at

least once per week.

•ESD Wrist Strap Tester – The wires inside of an ESD strap are prone to damage over time. When using an unmonitored kit, it is a

best practice to regularly test the strap prior to each service call, and at a minimum, test once per week. A wrist strap tester is the

best method for doing this test. If you do not have your own wrist strap tester, check with your regional office to find out if they have

one. To perform the test, plug the wrist-strap's bonding-wire into the tester while it is strapped to your wrist and push the button to

test. A green LED is lit if the test is successful; a red LED is lit and an alarm sounds if the test fails.

•Insulator Elements – It is critical to keep ESD sensitive devices, such as plastic heat sink casings, away from internal parts that are

insulators and often highly charged.

•Working Environment – Before deploying the ESD Field Service kit, assess the situation at the customer location. For example,

deploying the kit for a server environment is different than for a desktop or portable environment. Servers are typically installed in a

rack within a data center; desktops or portables are typically placed on office desks or cubicles. Always look for a large open flat work

area that is free of clutter and large enough to deploy the ESD kit with additional space to accommodate the type of system that is

being repaired. The workspace should also be free of insulators that can cause an ESD event. On the work area, insulators such as

Styrofoam and other plastics should always be moved at least 12 inches or 30 centimeters away from sensitive parts before physically

handling any hardware components

•ESD Packaging – All ESD-sensitive devices must be shipped and received in static-safe packaging. Metal, static-shielded bags are

preferred. However, you should always return the damaged part using the same ESD bag and packaging that the new part arrived in.

The ESD bag should be folded over and taped shut and all the same foam packing material should be used in the original box that the

new part arrived in. ESD-sensitive devices should be removed from packaging only at an ESD-protected work surface, and parts

should never be placed on top of the ESD bag because only the inside of the bag is shielded. Always place parts in your hand, on the

ESD mat, in the system, or inside an anti-static bag.

•Transporting Sensitive Components – When transporting ESD sensitive components such as replacement parts or parts to be

returned to Dell, it is critical to place these parts in anti-static bags for safe transport.

ESD protection summary

It is recommended that all field service technicians use the traditional wired ESD grounding wrist strap and protective anti-static mat at all

times when servicing Dell products. In addition, it is critical that technicians keep sensitive parts separate from all insulator parts while

performing service and that they use anti-static bags for transporting sensitive components.

After working inside your computer

About this task

After you complete any replacement procedure, ensure that you connect any external devices, cards, and cables before turning on your

computer.

Steps

1. Connect any telephone or network cables to your computer.

CAUTION: To connect a network cable, first plug the cable into the network device and then plug it into the

computer.

Working on your computer 7

2. Connect your computer and all attached devices to their electrical outlets.

3. Turn on your computer.

4. If required, verify that the computer works correctly by running the diagnostic tool.

8 Working on your computer

Major components of your system

1. Base cover

2. SSD shield cover

3. SSD memory

4. WWAN card shielding cover

5. WWAN card

6. System board

7. Smart card reader (optional)

8. Palmrest assembly

9. LCD panel

10. Keyboard

11. I/O board

12. System fan

13. Battery

14. Speaker

NOTE: Dell provides a list of components and their part numbers for the original system configuration purchased. These

parts are available according to warranty coverages purchased by the customer. Contact your Dell sales representative

for purchase options.

Major components of your system 9

Removing and Installing Components

Recommended tools

The procedures in this document require the following tools:

• Phillips #0 screwdriver

• Phillips #1 screwdriver

• Plastic scribe - Recommended for field technician

Screw list

The following table shows the screw list and the images for different components:

Table 1. Screw size list

Component Screw type Quantity Image

Base cover Captive screws 9

10 Removing and Installing Components

Component Screw type Quantity Image

4-cell battery M1.6x3.5 1

M2x3 4

6-cell battery M1.6x3.5 1

M2x3 8

WWAN Captive screw 1

M1.6x4.5 1

Smart card reader M2x2 2

Solid-state drive M2x2 1

Speaker M1.6x1.8 4

I/O board M1.6x3.5 4

System fan M2x3 2

Display cable bracket M1.6x3.5 1

Display assembly M2.5x5 6

M1.6x3.5 1

Power button M1.5x2.5 3

M2.5x5 3

Fingerprint bracket M1.5x2.5 3

System board M1.6x3.5 9

M2.5x5 1

Removing and Installing Components 11

Component Screw type Quantity Image

M1.6x4.5 1

Keyboard M1.6x2 4

M1.6x1.5 36

Disassembly and reassembly

SIM card tray

Removing the SIM card tray

Prerequisites

About this task

The following image indicate the location of the SIM card and provide a visual representation of the removal procedure.

Steps

1. Insert a pin into the release hole to release the SIM card tray [1].

2. Push the pin to disengage the lock, and eject the SIM card tray [2].

3. Slide the SIM card tray out of the slot on the computer [3].

12 Removing and Installing Components

Installing the SIM card tray

Prerequisites

If you are replacing a component, remove the necessary component before the installation procedure.

About this task

The following image indicates the location of the SIM card and provides a visual representation of the installation procedure.

Steps

Slide the SIM card tray into the slot in the computer [1], and push it to lock in place [2].

Next steps

MicroSD card

Removing the microSD card

Prerequisites

About this task

The following images indicate the location of the microSD card and provide a visual representation of the removal procedure.

Removing and Installing Components 13

Steps

1. Push the microSD card to eject it from the slot [1].

2. Remove the microSD card from the computer [2].

Installing the microSD card

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the microSD card and provides a visual representation of the installation procedure.

14 Removing and Installing Components

Steps

Insert the microSD card into its slot [1] until it clicks into place [2].

Next steps

1. Follow the procedure in After working on your computer .

Base cover

Removing the base cover

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD card.

3. Remove the SIM card tray.

NOTE: Always engage to cut off power from the battery before working inside your computer.

Removing and Installing Components 15

About this task

16 Removing and Installing Components

Steps

1. Loosen the nine captive screws that secure the base cover to the laptop.

2. Using a plastic scribe, pry the base cover from the top-left corner to open the base cover.

3. Lift the base cover away from the laptop.

Installing the base cover

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

Removing and Installing Components 17

Steps

1. Align and place the base cover on the palmrest and keyboard assembly, and snap the base cover into place.

2. Tighten the nine captive screws to secure the base cover to the laptop.

Next steps

1. Install the SIM card tray

2. Install the microSD card.

3. Follow the procedure in After working on your computer .

Battery

Lithium-ion battery precautions

CAUTION:

• Exercise caution when handling Lithium-ion batteries.

• Discharge the battery as much as possible before removing it from the system. This can be done by disconnecting

the AC adapter from the system to allow the battery to drain.

• Do not crush, drop, mutilate, or penetrate the battery with foreign objects.

• Do not expose the battery to high temperatures, or disassemble battery packs and cells.

• Do not apply pressure to the surface of the battery.

• Do not bend the battery.

• Do not use tools of any kind to pry on or against the battery.

18 Removing and Installing Components

• Ensure any screws during the servicing of this product are not lost or misplaced, to prevent accidental puncture or

damage to the battery and other system components.

• If the battery gets stuck inside your computer as a result of swelling, do not try to release it as puncturing, bending,

or crushing a lithium-ion battery can be dangerous. In such an instance, contact Dell technical support for

assistance. See www.dell.com/contactdell.

• Always purchase genuine batteries from www.dell.com or authorized Dell partners and resellers.

Removing the 4-cell battery

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD card.

3. Remove the SIM card tray.

4. Remove the Base cover.

5. Remove the Speakers.

NOTE: If battery was disconnected from system board for service, there will be a delay during system boot-up as the

system will undergo RTC battery reset.

About this task

The following images indicate the location of the battery and provide a visual representation of the removal procedure.

Removing and Installing Components 19

4-cell battery

Steps

1. Peel off the adhesive tape securing the wireless antenna cables in place and unroute the wireless antenna cables from the routing

guides.

NOTE: The cables for the wireless antennas are routed over the plastic bracket at the upper left corner and within

the routing channels along the left and bottom side of the battery. Technicians must be careful when unrouting the

antenna cables from their routing guides while they are still attached to the wireless card.

2. Remove the single (M1.6x3.5) screw and four (M2x3) screws that secures the battery.

3. Lift the battery from the left side of the system, and remove the battery from the laptop.

Installing the 4-cell battery

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

20 Removing and Installing Components

About this task

The following image indicates the location of the battery and provides a visual representation of the installation procedure.

NOTE: If battery was disconnected from system board for service, there will be a delay during system boot-up as the

system will undergo RTC battery reset.

Steps

1. Align and place the battery from the left side on the laptop.

2. Replace the single (M1.6x3.5) screw and four (M2x3) screws to secure the battery in place.

3. Route the wireless antenna cables on the routing guides and adhere the adhesive tape.

Next steps

1. Install the Speakers.

2. Install the Base cover.

3. Install the SIM card tray

4. Install the microSD card.

5. Follow the procedure in After working on your computer .

Removing and Installing Components 21

Removing the 6-cell battery

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD card.

3. Remove the SIM card tray.

4. Remove the Base cover.

5. Remove the Speakers.

About this task

The following images indicate the location of the battery and provide a visual representation of the removal procedure.

NOTE: If battery was disconnected from system board for service, there will be a delay during system boot-up as the

system will undergo RTC battery reset.

Steps

1. Peel off the adhesive tape securing the wireless antenna cables in place and unroute the wireless antenna cables from the routing

guides.

NOTE: The cables for the wireless antennas are routed over the plastic bracket at the upper left corner and within

the routing channels along the left and bottom side of the battery. Technicians must be careful when unrouting the

antenna cables from their routing guides while they are still attached to the wireless card.

2. Remove the single (M1.6x3.5) screw and eight (2x3) that secures the battery.

3. Lift the battery from the left side and remove the battery from the laptop.

Installing the 6-cell battery

About this task

The following image indicates the location of the battery and provides a visual representation of the installation procedure.

22 Removing and Installing Components

NOTE: If battery was disconnected from system board for service, there will be a delay during system boot-up as the

system will undergo RTC battery reset.

Steps

1. Align and place the battery from the left side on the laptop.

2. Install the single (M1.6x3.5) screw and eight (M2x3) screws to secure the battery in place.

3. Route the wireless antenna cables on the routing guides and adhere the adhesive tape.

Next steps

1. Install the Speakers.

2. Install the Base cover.

3. Install the SIM card tray

4. Install the microSD card.

5. Follow the procedure in After working on your computer .

WWAN card

Removing the WWAN card

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD card.

3. Remove the SIM card tray.

4. Remove the Base cover.

About this task

The following images indicate the location of the WWAN card and provide a visual representation of the removal procedure.

Removing and Installing Components 23

Steps

1. Shut down the system.

2. Press the power button and the B key until the Dell logo is displayed.

3. Follow the instructions displayed on the screen. After three beeps, you can start the WWAN card removal.

4. Peel off the adhesive tape that is securing the battery cable connector and disconnect the battery cable from the system board.

5. Using a flat head scribe, pry open the WWAN card shield covering the WWAN card.

6. Loosen the single captive screw and remove the WWAN card bracket.

7. Disconnect the antenna cables and remove the WWAN card.

Installing the WWAN card

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the WWAN card and provides a visual representation of the installation procedure.

24 Removing and Installing Components

Steps

1. Connect the antenna cable. to the correct nodes.

2. Align and slide the WWAN card into the connector on the system board.

3. Align the WWAN card bracket and tighten the single captive screw.

4. Align and place the WWAN card shield, press to fit it firmly to cover the WWAN card.

5. Connect the battery cable and adhere the adhesive cable.

Next steps

1. Install the Base cover.

2. Install the SIM card tray

3. Install the microSD card.

4. Follow the procedure in After working on your computer .

Solid-state drive

Removing the solid-state drive

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD card.

3. Remove the SIM card tray.

Removing and Installing Components 25

4. Remove the Base cover.

About this task

The following images indicate the location of the solid-state drive and provide a visual representation of the removal procedure.

Steps

1. Peel off the adhesive tape and disconnect the battery cable from the connector.

2. Using a flat head scribe pry open the SSD shield cover and lift it out of the system.

3. Remove the single M2x2 screw securing the SSD in place.

4. Slide the solid-state drive out of the M.2 slot.

Installing the solid-state drive

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the solid-state drive and provides a visual representation of the installation procedure.

26 Removing and Installing Components

Steps

1. Slide the solid-state drive into the M.2 slot.

2. Replace the single M2x2 screw that secures the solid-state drive.

3. Align the solid-state drive's shield to cover the SSD.

4. Reconnect the battery connector to the system board and fix back the adhesive tap onto the battery connector.

Next steps

1. Install the Base cover.

2. Install the SIM card tray

3. Install the microSD card.

4. Follow the procedure in After working on your computer .

Speakers

Removing the speaker

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD card.

3. Remove the SIM card tray.

4. Remove the Base cover.

Removing and Installing Components 27

5. Remove the Battery.

About this task

The following images indicate the location of the speaker and provide a visual representation of the removal procedure.

Steps

1. Peel off the adhesive tape that secures the battery cable to the system board.

2. Disconnect the speaker cable, and unroute the speaker cable from the routing guide.

3. Remove the four (M1.6x1.8) screws that secure the speakers, and remove the speakers from the laptop.

Installing the speaker

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the speaker and provides a visual representation of the installation procedure.

28 Removing and Installing Components

Steps

1. Align and place the speakers in the slot on the system.

2. Replace the four (M1.6x1.8) screws that secure the speakers to the laptop.

3. Route the speaker cables through the routing guide and connect the speaker cable to the connector.

4. Adhere the adhesive tape to secure the speaker cable.

Next steps

1. Install the Battery.

2. Install the Base cover.

3. Install the SIM card tray

4. Install the microSD card.

5. Follow the procedure in After working on your computer .

Removing and Installing Components 29

System fan

Removing the system fan

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD card.

3. Remove the SIM card tray.

4. Remove the Base cover.

About this task

The following images indicate the location of the system fan and provide a visual representation of the removal procedure.

Steps

1. Disconnect the I/O cable and unroute the antenna cable through the routing guide.

2. Disconnect the system fan cable from the connector and peel the adhesive tape securing the system fan cable.

3. Remove the two (M2x3) screws that secure the system fan.

4. Lift the system fan off the palmrest assembly.

30 Removing and Installing Components

Installing the system fan

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the system fan and provides a visual representation of the installation procedure.

Steps

1. Align and place the system fan onto the palmrest assembly.

2. Replace the two (M2x3) screws that secure the system fan in place.

3. Connect the system fan cable and adhere the adhesive tape to secure the system fan cable.

4. Route the antenna cable through the routing guide, and connect the I/O cable.

NOTE: Reconnect the battery after system repair.

Next steps

1. Install the Battery.

2. Install the Speakers.

3. Install the Base cover.

4. Install the SIM card tray

5. Install the microSD card.

Removing and Installing Components 31

6. Follow the procedure in After working on your computer .

I/O daughter board power cable

Removing the I/O daughter board power cable

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD card.

3. Remove the SIM card tray.

4. Remove the Base cover.

About this task

The following images indicate the location of the I/O daughter board power cable and provide a visual representation of the removal

procedure.

Steps

1. Disconnect the I/O daughter board power cable from the I/O board, and system board.

2. Unroute the I/O daughter board power cable from the routing channels adjacent to the system fan.

3. Remove the I/O daughter board power cable from the system.

Installing the I/O daughter board power cable

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the I/O daughter board power cable and provides a visual representation of the installation

procedure.

32 Removing and Installing Components

Steps

1. Route the I/O daughter board power cable on the routing channels adjacent to the system fan.

2. Connect the I/O daughter board power cable to the I/O board, and system board.

Next steps

1. Install the Base cover.

2. Install the SIM card tray

3. Install the microSD card.

4. Follow the procedure in After working on your computer .

I/O board

Removing the I/O board

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD card.

3. Remove the SIM card tray.

4. Remove the Base cover.

5. Remove the System Fan.

About this task

The following image indicates the location of the I/O board and provides a visual representation of the removal procedure.

Removing and Installing Components 33

Steps

1. Disconnect the I/O daughter board data cable, fingerprint reader cable, and LED board cable from the I/O board.

2. Remove the four M1.6x3.5 screws and lift the I/O board out of the laptop.

Installing the I/O board

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the I/O board and provides a visual representation of the installation procedure.

34 Removing and Installing Components

Steps

1. Align and place the I/O board on the system.

2. Replace the four M1.6x3.5 screws to secure the I/O board in place.

3. Connect the LED board cable, fingerprint reader cable, and I/O daughter board data cable to the connectors on the I/O board.

NOTE: Reconnect the battery cable after laptop repair is completed.

Next steps

1. Install the System Fan.

2. Install the Base cover.

3. Install the SIM card tray

4. Install the microSD card.

5. Follow the procedure in After working on your computer .

System board

Removing the system board

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD card.

3. Remove the SIM card tray.

4. Remove the Base cover.

5. Remove the Solid-state drive.

6. Remove the WWAN.

7. Remove the Battery.

8. Remove the Speakers.

9. Remove the System Fan.

About this task

The following images indicate the location of the system board assembly and provide a visual representation of the removal procedure.

Removing and Installing Components 35

36 Removing and Installing Components

Steps

1. Remove the single M1.6x3.5 screw securing the display cable bracket in place.

2. Disconnect the display cable and camera cable from the system board.

NOTE: Technicians must disconnect the display cable from the system board by pulling the pull tab in a direct

upward motion to prevent damage to the connector's pins.

Removing and Installing Components 37

3. Remove the single (M2x2) screw securing the wireless module bracket and lift the bracket.

4. Disconnect the antenna cable from the wireless module, and unroute the antenna cable from the metal clips.

5. Unroute the WWAN antenna cable from the routing guide.

6. Remove the two M1.6x4.5 screws securing the two system board hooks to the system board.

7. Disconnect the two WWAN Darwin cables from the system.

8. Disconnect the proximity sensor cable from the system board.

9. Remove the three M1.6x3.5 screws from the Type-C bracket and five M1.6x3.5 screws that secure the system board. Hold the left

side of the system board and partially lift up the system board from the system.

10. Flip over the system board from the top side of the system board, disconnect the I/O daughter board data cable and remove the

system board from the system.

Installing the system board

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the system board assembly and provides a visual representation of the installation procedure.

38 Removing and Installing Components

Removing and Installing Components 39

40 Removing and Installing Components

Steps

1. Flip the system board over and then align and place the system board on the system, and connect the I/O daughter board data cable.

2. Install the three M1.6x3.5 screws securing the Type-C bracket and five M1.6x3.5 screws that secures the system board.

3. Connect the proximity sensor cable to the system board.

4. Connect the two WWAN Darwin cables to the system board.

5. Install the two M1.6x4.5 screws securing the two system board hooks to the system board.

NOTE: Do not slide the hooks on the system board to fit the positioning studs into the openings, as this will damage

the system board. When installing the hooks, align the positioning studs on the hooks over the openings on the

system board and then install the hooks on the system board.

Removing and Installing Components 41

6. Route the WWAN antenna cable on the routing guide.

7. Route the antenna cable and connect to the wireless module.

8. Place the wireless module bracket, and tighten the single (M2x2) screw securing the wireless module bracket.

9. Connect the display cable and camera cable to the system board.

10. Replace the single M1.6x3.5 screw to secure the display cable bracket in place.

Next steps

1. Install the System Fan.

2. Install the Speakers.

3. Install the Battery.

4. Install the Solid-state drive.

5. Install the WWAN.

6. Install the Base cover.

7. Install the SIM card tray

8. Install the microSD card.

9. Follow the procedure in After working on your computer .

Display assembly

Removing the display assembly

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD card.

3. Remove the SIM card tray.

4. Remove the Base cover.

About this task

The following images indicate the location of the display assembly and provide a visual representation of the removal procedure.

NOTE: The display assembly removal procedure is the same for both laptop and convertible chassis.

42 Removing and Installing Components

Removing and Installing Components 43

Steps

1. Remove the single M1.6x3.5 screw securing the display-cable bracket, and remove the display-cable bracket .

2. Disconnect the display cable from the system board by pulling the pull tab in a direct upward motion, and disconnect and peel back the

camera cable from the system board.

NOTE: Technicians must disconnect the display cable from the system board by pulling the pull tab in a direct

upward motion to prevent damage to the connector's pins.

3. Open the display assembly to 90-degree angle and flip over the system, and then place the system on a flat surface.

4. Remove the six M2.5x5 screws that secure the display assembly to the laptop, press the edges of the laptop near the hinges, and lift

the hinges in the upward direction away from the laptop.

5. Lift the display assembly off the laptop.

Installing the display assembly

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

NOTE: The display assembly installation procedure is the same for both laptop and convertible chassis.

About this task

The following image indicates the location of the display assembly and provides a visual representation of the installation procedure.

44 Removing and Installing Components

Removing and Installing Components 45

Steps

1. Align and place the system chassis under the hinges of the display assembly.

2. Install the six M2.5x5 screws that secure the display hinges to the laptop.

3. Connect the display cable to the system board. Connect and adhere the camera cable to the system board.

4. Place the display cable bracket in place and install the single M1.6x3.5 screw securing the display cable bracket.

Next steps

1. Install the Base cover.

2. Install the SIM card tray

3. Install the microSD card.

4. Follow the procedure in After working on your computer .

Keyboard

Removing the keyboard

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD card.

3. Remove the SIM card tray.

4. Remove the Base cover.

46 Removing and Installing Components

5. Remove the Solid-state drive.

6. Remove the Speakers.

7. Remove the Battery.

8. Remove the Display assembly.

9. Remove the Fan.

10. Remove the I/O board .

11. Remove the System board.

About this task

The following images indicate the location of the keyboard and provide a visual representation of the removal procedure.

Steps

1. Peel back the antenna cable, WWAN Darwin cable, touchpad FPC, LED FFC from the keyboard.

2. Disconnect the backlight cable and the keyboard cable from the connectors on the touchpad.

3. Remove the four M1.6x2 and thirty-six M1.6x1.5 screws that secures the keyboard to the palmrest.

4. Lift the keyboard from the palmrest.

Removing and Installing Components 47

Installing the keyboard

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the keyboard and provides a visual representation of the installation procedure.

Steps

1. Align and place the keyboard on the palmrest.

2. Install the four M1.6x2 and thirty-six M1.6x1.5 screws to secure the keyboard.

3. Connect the keyboard cable and backlight cable to the connectors on the touchpad.

4. Adhere the antenna cable, WWAN Darwin cable, touchpad FPC, LED FFC to the keyboard.

Next steps

1. Install the System board

2. Install the I/O board.

48 Removing and Installing Components

3. Install the Fan.

4. Install the Display assembly.

5. Install the Battery.

6. Install the Speakers.

7. Install the Solid-state drive.

8. Install the Base cover.

9. Install the SIM card tray

10. Install the microSD card.

11. Follow the procedure in After working on your computer .

Power button with finger print reader (optional)

Removing the power button with fingerprint reader

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD card.

3. Remove the SIM card tray.

4. Remove the Base cover.

5. Remove the Fan.

6. Remove the I/O board .

About this task

The following images indicate the location of the fingperprint reader and provide a visual representation of the removal procedure.

Steps

1. Remove the three M2.5x5 screws securing the LCD hinges in place.

2. Rotate and lift the hinges up to remove the hinges.

3. Remove the three M1.5x2.5 screws securing the fingerprint bracket in place.

4. Remove the fingerprint reader bracket from the system.

Removing and Installing Components 49

5. Peel off the power button with the fingerprint reader assembly from the sponge on the palm rest, and remove the power button with

fingerprint reader assembly from the system.

Installing the power button with fingerprint reader

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following images indicate the location of the fingperprint reader and provide a visual representation of the installation procedure.

Steps

1. Align and place the fingerprint reader assembly on the system and adhere the power button with the fingerprint reader assembly on

the sponge on the palmrest.

2. Align and place the fingerprint reader bracket in place, and install the three M1.5x2.5 screws securing the fingerprint bracket.

3. Rotate and align the hinges down in place.

4. Install the three M2.5x5 screws securing the LCD hinges in place.

Next steps

1. Install the I/O board.

2. Install the Fan.

3. Install the Base cover.

4. Install the SIM card tray

5. Install the microSD card.

6. Follow the procedure in After working on your computer .

50 Removing and Installing Components

Power button

Removing the power-button

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD card.

3. Remove the SIM card tray.

4. Remove the Base cover.

5. Remove the Speakers.

6. Remove the Battery.

7. Remove the Display assembly.

8. Remove the Fan.

9. Remove the I/O board .

About this task

The following images indicate the location of the power-button and provide a visual representation of the removal procedure.

Steps

1. Remove the three M1.5x2.5 screws securing the fingerprint reader bracket.

2. Remove the power button bracket from the system.

3. Peel off the power button assembly from the palm rest and remove the power button assembly from the system.

Installing the power-button

About this task

The following image displays the installation procedure.

Removing and Installing Components 51

Steps

1. Align and place the power button assembly on the system. Adhere the power button assembly on the palm rest.

2. Install the power button bracket on the system.

3. Install the three M1.5x2.5 screws securing the fingerprint reader bracket.

Next steps

1. Install the I/O board.

2. Install the Fan.

3. Install the Display assembly.

4. Install the Battery.

5. Install the Speakers.

6. Install the Base cover.

7. Install the SIM card tray

8. Install the microSD card.

9. Follow the procedure in After working on your computer .

Smart card reader board

Removing the Smart card reader

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD card.

3. Remove the SIM card tray.

4. Remove the Base cover.

5. Remove the Speakers.

6. Remove the Battery.

52 Removing and Installing Components

About this task

Steps

1. Disconnect the touchpad FPC from the touchpad module, and peel it back from the touchpad bracket.

2. Disconnect the smart card reader cable from the I/O daughter board and peel it back from the keyboard.

3. Remove the two M2x2 screw securing the smart card reader in place, and lift the smart card reader away from the laptop.

Installing the smartcard reader

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

Removing and Installing Components 53

About this task

Steps

1. Align and place the smart card reader on the system, and install the two M2x2 screws securing the smart card reader.

2. Connect the I/O daughter board cable and smart card reader cable securing the cables.

3. Connect the touchpad FPC on the touchpad module, and adhere it back on the touchpad bracket.

Next steps

1. Install the Battery.

2. Install the Speakers.

3. Install the Base cover.

4. Install the microSD card.

5. Follow the procedure in After working on your computer .

54 Removing and Installing Components

Palmrest assembly

Removing the palmrest assembly

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD card.

3. Remove the SIM card tray.

4. Remove the Base cover.

5. Remove the Solid-state drive.

6. Remove the Speakers.

7. Remove the Battery.

8. Remove the Display assembly.

9. Remove the System Fan.

10. Remove the I/O board .

11. Remove the Power button.

12. Remove the System board.

13. Remove the Keyboard.

About this task

The following images indicate the location of the palmrest and provide a visual representation of the removal procedure.

Steps

After performing the preceding steps, you are left with the palmrest assembly.

Installing the palmrest assembly

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the palmrest assembly and provides a visual representation of the installation procedure.

Removing and Installing Components 55

Steps

Transfer the components onto the new palmrest assembly.

Next steps

1. Install the Keyboard.

2. Install the System board

3. Install the FPC.

4. Install the I/O board.

5. Install the System Fan.

6. Install the Display assembly.

7. Install the Battery.

8. Install the Speakers.

9. Install the Solid-state drive.

10. Install the Base cover.

11. Install the SIM card tray

12. Install the microSD card.

13. Follow the procedure in After working on your computer .

56 Removing and Installing Components

System setup

System setup enables you to manage your tabletdesktopnotebook hardware and specify BIOS level options. From the System setup, you

can:

• Change the NVRAM settings after you add or remove hardware

• View the system hardware configuration

• Enable or disable integrated devices

• Set performance and power management thresholds

• Manage your computer security

Topics:

•Entering BIOS without keyboard

•System setup options

•System Log

•Updating the BIOS

•Updating your system BIOS using a USB flash drive

•System and setup password

Entering BIOS without keyboard

Steps

1. Press the power button to turn on your tablet.

2. Press and hold the Volume Up button when the Dell logo appears on the screen.

3. When the F12 boot selection menu appears, select BIOS Setup using the Volume Up button.

4. Press the Volume Down button to enter BIOS setup program.

System setup options

NOTE: Depending on the tabletcomputerlaptop and its installed devices, the items listed in this section may or may not

appear.

General screen options

This section lists the primary hardware features of your computer.

Option Description

System

Information

• System Information: Displays BIOS Version, Service Tag, Asset Tag, Ownership Tag, Ownership Date,

Manufacture Date, and the Express Service Code.

• Memory Information: Displays Memory Installed, Memory Available, Memory Speed, Memory Channels Mode,

Memory Technology

• Processor Information: Displays Processor Type, Core Count, Processor ID, Current Clock Speed, Minimum

Clock Speed, Maximum Clock Speed, Processor L2 Cache, Processor L3 Cache, HT Capable, and 64-Bit

technology.

• Device Information: Displays Primary Hard Drive, Video Controller, Video BIOS Version, Video Memory, Panel

Type, Native Resolution, Audio Controller, Wi-Fi Device, Cellular Device, Bluetooth Device.

Battery

Information

Displays the battery status and the type of AC adapter connected to the computer.

System setup 57

Option Description

Boot Sequence Boot Sequence Allows you to change the order in which the computer attempts to find an operating

system. The options are:

• Windows Boot Manager

By default, the options is checked.

Boot List Options Allows you to change the boot list option:

• UEFI (The option is enabled by default)

Advanced Boot

Options

Allows you the legacy option ROMs to load. By default, all the option are disabled.

UEFI Boot Path

SecurityOptions

Allows you to control whether or not the system will prompt to the user to enter the Admin password, when a

user selects a UEFI boot path from the F12 boot Menu.

•Always, Except Internal HDD. This option is enabled by default.

•Always, Except Internal HDD&PXE

•Never

NOTE: These options have no relevance if the Admin password is not set BIOS settings.

Date/Time Allows you to change the date and time.

System Configuration screen options

Option Description

SMART Reporting This field controls whether hard drive errors for integrated drives are reported during system startup. This

technology is part of the SMART (Self-Monitoring Analysis and Reporting Technology) specification. This option is

disabled by default.

• Enable SMART Reporting

USB Configuration This is an optional feature.

This field configures the integrated USB controller. If Boot Support is enabled, the system is allowed to boot any

type of USB Mass Storage Devices—HDD, memory key, floppy.

If USB port is enabled, device attached to this port is enabled and available for OS.

If USB port is disabled, the OS cannot see any device attached to this port.

The options are:

• Enable USB Boot Support—enabled by default

• Enable External USB Port—enabled by default

NOTE: USB keyboard and mouse always work in the BIOS setup irrespective of these settings.

USB PowerShare This field configures the USB PowerShare feature behavior. This option allows you to charge external devices

using the stored system battery power through the USB PowerShare port. This option is disabled by default

Audio This field enables or disables the integrated audio controller. By default, the Enable Audio option is selected. The

options are:

• Enable Microphone—enabled by default

• Enable Internal Speaker—enabled by default

Keyboard

Illumination

This field lets you choose the operating mode of the keyboard illumination feature. The keyboard brightness level

can be set from 0% to 100%. The options are:

• Bright (default)

• Dim (50%)

58 System setup

Option Description

Keyboard

Backlight Timeout

on Battery

The Keyboard Backlight Timeout dims out with the Battery option. The main keyboard illumination feature is not

affected. Keyboard Illumination will continue to support the various illumination levels. This field has an effect

when the backlight is enabled. The options are:

• 5 sec

• 10 sec—enabled by default

• 15 sec

• 30 sec

• 1 min

• 5 min

• 15 min

• Never

Keyboard

Backlight Timeout

on AC

The Keyboard Backlight Timeout dims out with AC option. The main keyboard illumination feature is not affected.

Keyboard Illumination will continue to support the various illumination levels. This field has an effect when the

backlight is enabled. The options are:

• 5 sec

• 10 sec—enabled by default

• 15 sec

• 30 sec

• 1 min

• 5 min

• 15 min

• Never

Unobtrusive Mode This option, when enabled, pressing Fn+shift+B turns off all light and sound emissions in the system. To resume

normal operation, press Fn+shift+B again. This option is disabled by default.

Miscellaneous

Devices

Allows you to enable or disable the following devices:

• Enable Front Camera—enabled by default

• Enable Back Camera—enabled by default

• Secure Digital (SD) card—enabled by default

• Secure Digital (SD) card boot

• Secure Digital (SD) card read-only-mode

System Configuration screen options

Option Description

Integrated NIC Does not allow you to control the on-board LAN controller. The options are:

•DisabledThe internal LAN in off and not visible to the operating system.

•DisabledThe internal LAN is enabled.

•Disabled w/PXEThe internal LAN is enabled (with PXE boot). This option is enabled by default.

Drives Allows you to configure the various drives on board. All drives are enabled by default. The option is:

•M.2 2230 PCI-e SSD

SMART Reporting This field controls whether hard drive errors for integrated drives are reported during system startup. This

technology is part of the SMART (Self Monitoring Analysis and Reporting Technology) specification. This option is

disabled by default.

•Enable SMART Reporting

USB Configuration This is an optional feature.

This field configures the integrated USB controller. If Boot Support is enabled, the system is allowed to boot any

type of USB Mass Storage Devices (HDD, memory key, floppy).

If USB port is enabled, device attached to this port is enabled and available for OS.

System setup 59

Option Description

If USB port is disabled, the OS cannot see any device attached to this port.

The options are:

•Enable USB Boot Support

•Enable External USB Port

NOTE: Both the option is enabled by default.

Dell Type-C dock

configuration

Does not support this configuration

Thunderbolt

Adapter

configuration:

Allows you to configure the Thunderbolt™ adapter security settings within the Operating System.

NOTE: Security Levels are not applicable or enforced in the Pre-boot environment.

The options are:

•Enable Thunderbolt™ Technology SupportThis option is enabled by default.

•Enable Thunderbolt™ Adapter Boot Support

•Enable Thunderbolt™ Adapter Pre-boot Modules

•Security level - No Security

•Security level - User AuthorizationThis option is enabled by default.

•Security level - Secure Correct

•Security level - Display Port only

USB PowerShare Allows you to charge external devices using the stored system battery power through the USB PowerShare port.

This field can also configure the USB PowerShare feature behavior. By default, the Enable USB PowerShare is

disabled.

Audio Allows you to enable or disable the integrated audio controller. By default, the Enable Audio option is selected.

The options are:

•Enable MicrophoneThis option is enabled by default.

•Enable Internal Speaker This option is enabled by default.

Keyboard

Illumination

Allows you to choose the operating mode of the keyboard illumination feature. The keyboard brightness level can

be set from 0% to 100%. The options are:

•Disabled

•Dim

•Bright This option is enabled by default.

NOTE: The <Fn+F10> hotkey can be used to change the setting.

Keyboard

Backlight Timeout

on AC

Allows you to define the time-out value for the keyboard Backlight when an AC adapter is plugged into the

system. The main keyboard illumination feature is not affected. Keyboard Illumination will continue to support the

various illumination levels. This field has an effect when the backlight is enabled. The options are:

•5 seconds

•10 seconds This option is enabled by default.

•15 seconds

•30 seconds

•1 minute

•5 minute

•15 minute

•never

Keyboard

Backlight Time-

out on Battery

Allows you to define the Keyboard Backlight Time-out dims out with Battery option. The main keyboard

illumination feature is not affected. Keyboard Illumination will continue to support the various illumination levels.

This field has an effect when the backlight is enabled. The options are:

•5 seconds

•10 seconds This option is enabled by default.

•15 seconds

60 System setup

Option Description

•30 seconds

•1 minute

•5 minute

•15 minute

•never

Touchscreen Does not support this option

Unobtrusive Mode Allows you to select the option. When enabled, pressing Fn+F7 turns off all light and sound emissions in the

system. To resume normal operation, press Fn+F7 again. This option is disabled by default.

Miscellaneous

Devices

Allows you to enable or disable various on board devices:

•Enable Camera This option is enabled by default.

•Enable Secure Digital(SD) CardThis option is enabled by default.

•Secure Digital(SD) Card read only mode

Video screen options

Option Description

LCD Brightness Allows you to set the display brightness depending up on the power source (On Battery and On AC).

NOTE: The video setting will be visible only when a video card is installed into the system.

Security screen options

Option Description

Admin Password Allows you to set, change, or delete the administrator (admin) password.

NOTE: You must set the admin password before you set the system or hard drive password.

Deleting the admin password automatically deletes the system password and the hard drive

password.

NOTE: Password changes take effect immediately.

By default, the drive will not have a password set.

System Password Allows you to set, change or delete the system password.

NOTE: Password changes take effect immediately.

By default, the drive will not have a password set.

Password

Configuration

Allows you to determine the minimum and maximum length of Administrator and System passwords.

Password Bypass Allows you to disable or enable the permission to bypass the System and the Internal hard drive password, when

they are set. The options are:

•Disabled. This option is selected by default.

•Reboot bypass

Password Change Allows you to enable or disable permission to the System and Hard Drive passwords when the admin password is

set.

Allow Non-Admin Password Changes This option is selected by default.

UEFI Capsule

Firmware Updates

This option controls whether the system allows BIOS updates via UEFI capsule update packages.

Enable UEFI Capsule Firmware Updates option is selected by default.

System setup 61

Option Description

NOTE: Disabling this option will block BIOS updates from services such as Microsoft Windows

Update and Linux Vendor Firmware Service (LVFS).

TPM 2.0 Security Allows you to enable the Trusted Platform Module (TPM) during POST.

You can control whether the trusted platform module is visible to the operating system. The option is:

•TPM on This option is selected by default.

•Clear

•PPI Bypass for Disable Commands

•PPI Bypass for Clear Command" in TPM 2.0 Security.

•Attestation Enable. This option is selected by default.

•PPI Bypass for Disable Commands

•Key Storage Enable. This option is selected by default.

•SHA-256. This option is selected by default.

CAUTION: For the TPM upgrade/downgrade process, it is recommended to complete the process

in an AC power with AC adapter plugged into the computer. The upgrade/downgrade process

without the AC adapter plugged in might damage the computer or hard disk.

NOTE: Disabling this option does not change any settings you have made to the TPM, nor does it

delete or change any information or keys you may have stored in the TPM. Changes to this setting

take effect immediately.

Absolute (R) Allows you to activate or disable the optional Computrace Service from Absolute software. The options are:

• Deactivate

• Disable

• Activate

NOTE: The Activate and Disable options will permanently activate or disable the feature and no

further changes will be allowed

Default setting: Activate

Admin Setup

Lockout

Allows you to prevent users from entering the setup when an Administrator password is set.

Enable Admin Setup Lockout This option is not selected by default.

Master Password

Lockout

Allows you to prevent users from entering the setup when an Master password is set. Hard disk passwords need

to be cleared before the setting can be changed.

Enable Master Password Lockout This option is not selected by default.

SSM Security

Mitigation

Allows you to enable or disable additional UEFI SMM Security Mitigation protections. The OS can use the feature

to help protect the secure environment created by virtualization based security.

SSM Security Mitigation This option is disabled by default.

Secure Boot

Option Description

Secure Boot

Enable

This option enables or disables the Secure Boot feature.

• Disabled

• Enabled

Default setting: Enabled.

Expert Key

Management

Allows you to manipulate the security key databases only if the system is in Custom Mode. The Enable Custom

Mode option is disabled by default.

Custom Mode Key

Management

Allows you to manage the security key databases only if the system is in Custom Mode .The options are:

62 System setup

Option Description

•PK. This option is selected by default.

•KEK

•db

•dbx

NOTE: If you disable the Enable Custom Mode, all the changes made will be erased and the keys

will restore to default settings. Save to File will save the key to a user-selected file.

Intel software Guard Extensions

Option Description

Intel SGX Enable This option enables or disables to provide a secured environment for running code/storing sensitive information in

the context of the main OS. The options are:

•Disabled

•Enabled

•Software Controlled.This option is selected by default.

Enclave Memory

Size

Allows you to reserve the memory size. The memory size can be set from 32 MB to 128 MB, these options are

disabled by default. The options are:

•32 MB

•64 MB

•128 MB

Performance screen options

Option Description

Multi Core

Support

This field specifies whether the process has one or all cores enabled. The performance of some applications

improves with the additional cores. This option is enabled by default. Allows you to enable or disable multi-core

support for the processor.

•AllThis option is enabled by default.

•1

•2

•3

Intel SpeedStep Allows you to enable or disable the Intel SpeedStep mode of the processor.

•Enable Intel SpeedStep

Default setting: The option is enabled.

C-States Control Allows you to enable or disable the additional processor sleep states.

•C states

Default setting: The option is enabled.

Intel TurboBoost Allows you to enable or disable the Intel TurboBoost mode of the processor.

•Enable Intel TurboBoost

Default setting: The option is enabled.

HyperThread

Control

Allows you to enable or disable the HyperThreading in the processor.

•Disabled

•EnabledThis option is enabled by default.

System setup 63

POST Behavior

Option Description

Adapter Warnings Allows you to enable or disable the system setup (BIOS) warning messages when you use certain power adapters.

Enable Adapter Warnings This option is selected by default.

Numlock Enable Allows you to enable the Numlock option when the computer boots.

•Enable Network This option is enabled by default.

Fn Lock Options Allows you to let hot key combinations Fn + Esc toggle the primary behavior of F1 – F12, between their standard

and secondary functions. If you disable this option, you cannot toggle dynamically the primary behavior of these

keys. The available options are:

•Lock Mode Disable/Standard This option is selected by default.

•Lock Mode Enable/Secondary

Fastboot Allows you to speed up the boot process by bypassing some of the compatibility steps. The options are:

•Minimal This option is selected by default.

•Thorough

•Auto

Extended BIOS

POST Time

Allows you to create an additional pre-boot delay. The options are:

•0 seconds This option is enabled by default.

•5 seconds

•10 seconds

Warnings and

Errors

Allows you to select in the BIOS setup options that cause the boot process to pause only, when warnings or errors

are detected rather than stop, prompt and wait for user input. The options are:

Prompt on Warnings and Errors. This option is enabled by default.

Continue on Warnings

Sign of Life Indication

Virtualization Support options

Option Description

Virtualization Allows you to enable or disable the Intel Virtualization Technology.

Enable Intel Virtualization Technology This option is selected by default.

VT for Direct I/O Enables or disables the Virtual Machine Monitor (VMM) from utilizing the additional hardware capabilities provided

by Intel® Virtualization technology for direct I/O.

Enable VT for Direct I/O This option is selected by default.

Trusted Execution This option specifies whether a Measured Virtual Machine Monitor (MVMM) can utilize the additional hardware

capabilities provided by Intel Trusted Execution Technology. The TPM Virtualization Technology, and Virtualization

technology for direct I/O must be enabled to use this feature.

Trusted Execution This option is disabled by default.

Wireless screen options

Option Description

Wireless Device

Enable

Allows you to enable or disable the internal wireless devices.

• WWAN/GPS

64 System setup

Option Description

• WLAN

• Bluetooth

All the options are enabled by default.

NOTE: IMEI number for WWAN can be found on the outer box or the WWAN card.

Maintenance

Option Description

Service Tag Displays the Service Tag of your computer.

Asset Tag Allows you to create a system asset tag if an asset tag is not already set. This option is not set by default.

BIOS Downgrade Allows you to control flashing of the system firmware to previous revisions. The option are:

Allows BIOS Downgrade This option is enabled by default.

Data Wipe Allows you to securely erase data from all internal storage devices. The process adheres to Serial ATA Security

Erase and eMMC JEDEC Sanitize specifications. The option are:

Wipe on Next Boot This option is disabled by default.

BIOS Recovery Allows you to recover from certain computed BIOS conditions from a recovery file on the user primary hard drive

or an external USB key. When 'Enabled' is selected BIOS stores the recovery file on the user primary hard

drive.The option are:

BIOS Recovery from Hard Drive This option is enabled by default.

System logs screen options

Option Description

BIOS Events Allows you to view and clear the System Setup (BIOS) POST events.

Thermal Events Allows you to view and clear the System Setup (Thermal) events.

Power Events Allows you to view and clear the System Setup (Power) events.

System Log

Option Description

BIOS Events Allows you to view and clear the System Setup (BIOS) POST events.

Thermal Events Allows you to view and clear the System Setup (Thermal) events.

Power Events Allows you to view and clear the System Setup (Power) events.

Updating the BIOS

Prerequisites

It is recommended to update your BIOS (System setup) on replacing the system board or if an update is available. Ensure that your

tabletnotebookdesktop battery is fully charged and connected to a power outlet.

Steps

1. Restart the tabletnotebookdesktop.

2. Go to Dell.com/support.

System setup 65

3. Enter the Service Tag or Express Service Code and click Submit.

NOTE: To locate the Service Tag, click Where is my Service Tag?

NOTE: If you cannot find your Service Tag, click Detect My Product. Proceed with the instructions on screen.

4. If you are unable to locate or find the Service Tag, click the Product Category of your tabletnotebookdesktop.

5. Choose the Product Type from the list.

6. Select your tabletnotebookdesktop model and the Product Support page of your tabletnotebookdesktop appears.

7. Click Get drivers and click View All Drivers.

The Drivers and Downloads page opens.

8. On the Drivers and Downloads screen, under the Operating System drop-down list, select BIOS.

9. Identify the latest BIOS file and click Download File.

You can also analyze which drivers need an update. To do this for your product, click Analyze System for Updates and follow the

instructions on the screen.

10. Select your preferred download method in the Please select your download method below window, click Download File.

The File Download window appears.

11. Click Save to save the file on your tabletnotebookdesktop.

12. Click Run to install the updated BIOS settings on your tabletnotebookdesktop.

Follow the instructions on the screen.

Next steps

NOTE: It is recommended not to update the BIOS version for more than 3 revisions. For example: If you want to update

the BIOS from 1.0 to 7.0, then install version 4.0 first and then install version 7.0.

Updating your system BIOS using a USB flash

drive

About this task

If the system cannot load into Windows, but there is still a need to update the BIOS, download the BIOS file using another system and

save it to a bootable USB Flash Drive.

NOTE: You will need to use a bootable USB flash drive. Please refer to the following article for further details How to

Create a Bootable USB Flash Drive using Dell Diagnostic Deployment Package (DDDP)

Steps

1. Download the BIOS update .EXE file to another system.

2. Copy the file e.g. O9010A12.EXE onto the bootable USB flash drive.

3. Insert the USB flash drive into the system that requires the BIOS update.

4. Restart the system and press F12 when the Dell splash logo appears to display the One Time Boot Menu.

5. Using arrow keys, select USB Storage Device and click Enter.

6. The system will boot to a Diag C:\> prompt.

7. Run the file by typing the full filename, for example, O9010A12.exe and press Enter.

8. The BIOS Update Utility will load. Follow the instructions on screen.

66 System setup

Figure 1. DOS BIOS Update Screen

System and setup password

Table 2. System and setup password

Password type Description

System password Password that you must enter to log on to your system.

Setup password Password that you must enter to access and make changes to the

BIOS settings of your computer.

You can create a system password and a setup password to secure your computer.

CAUTION: The password features provide a basic level of security for the data on your computer.

CAUTION: Anyone can access the data stored on your computer if it is not locked and left unattended.

NOTE: System and setup password feature is disabled.

Assigning a system setup password

Prerequisites

You can assign a new System or Admin Password only when the status is in Not Set.

About this task

To enter the system setup, press F2 immediately after a power-on or reboot.

Steps

1. In the System BIOS or System Setup screen, select Security and press Enter.

The Security screen is displayed.

2. Select System/Admin Password and create a password in the Enter the new password field.

Use the following guidelines to assign the system password:

• A password can have up to 32 characters.

• The password can contain the numbers 0 through 9.

• Only lower case letters are valid, upper case letters are not allowed.

System setup 67

• Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).

3. Type the system password that you entered earlier in the Confirm new password field and click OK.

4. Press Esc and a message prompts you to save the changes.

5. Press Y to save the changes.

The computer reboots.

Deleting or changing an existing system setup password

Prerequisites

Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or change the existing System and

Setup password. You cannot delete or change an existing System or Setup password, if the Password Status is Locked.

About this task

To enter the System Setup, press F2 immediately after a power-on or reboot.

Steps

1. In the System BIOS or System Setup screen, select System Security and press Enter.

The System Security screen is displayed.

2. In the System Security screen, verify that Password Status is Unlocked.

3. Select System Password, alter or delete the existing system password and press Enter or Tab.

4. Select Setup Password, alter or delete the existing setup password and press Enter or Tab.

NOTE: If you change the System and/or Setup password, re enter the new password when prompted. If you delete

the System and Setup password, confirm the deletion when prompted.

5. Press Esc and a message prompts you to save the changes.

6. Press Y to save the changes and exit from System Setup.

The computer restarts.

68 System setup

Troubleshooting

Dell SupportAssist Pre-boot System Performance

Check diagnostics

About this task

The SupportAssist diagnostics (also known as system diagnostics) performs a complete check of your hardware. The Dell SupportAssist

Pre-boot System Performance Check diagnostics is embedded with the BIOS and is launched by the BIOS internally. The embedded

system diagnostics provides a set of options for particular devices or device groups allowing you to:

• Run tests automatically or in an interactive mode

• Repeat tests

• Display or save test results

• Run thorough tests to introduce additional test options to provide extra information about the failed device(s)

• View status messages that inform you if tests are completed successfully

• View error messages that inform you of problems encountered during testing

NOTE: Some tests for specific devices require user interaction. Always ensure that you are present at the computer

terminal when the diagnostic tests are performed.

For more information, see Resolve Hardware Issues With Built-in and Online Diagnostics (SupportAssist ePSA, ePSA or PSA Error

Codes) .

Running the SupportAssist Pre-Boot System Performance

Check

Steps

1. Turn on your computer.

2. As the computer boots, press the F12 key as the Dell logo appears.

3. On the boot menu screen, select the Diagnostics option.

4. Click the arrow at the bottom left corner.

Diagnostics front page is displayed.

5. Click the arrow in the lower-right corner to go to the page listing.

The items detected are listed.

6. To run a diagnostic test on a specific device, press Esc and click Yes to stop the diagnostic test.

7. Select the device from the left pane and click Run Tests.

8. If there are any issues, error codes are displayed.

Note the error code and validation number and contact Dell.

System diagnostic lights

Battery-status light

Indicates the power and battery-charge status.

Solid white — Power adapter is connected and the battery has more than 5 percent charge.

Amber — Computer is running on battery and the battery has less than 5 percent charge.

Off

Troubleshooting 69

• Power adapter is connected and the battery is fully charged.

• Computer is running on battery and the battery has more than 5 percent charge.

• Computer is in sleep state, hibernation, or turned off.

The power and battery-status light blinks amber along with beep codes indicating failures.

For example, the power and battery-status light blinks amber two times followed by a pause, and then blinks white three times followed by

a pause. This 2,3 pattern continues until the computer is turned off indicating no memory or RAM is detected.

The following table shows different power and battery-status light patterns and associated problems.

Table 3. LED codes

Diagnostic light codes Problem description

2,1 Processor failure

2,2 System board: BIOS or ROM (Read-Only Memory) failure

2,3 No memory or RAM (Random-Access Memory) detected

2,4 Memory or RAM (Random-Access Memory) failure

2,5 Invalid memory installed

2,6 System-board or chipset error

2,7 Display failure

2,8 LCD power rail failure. Replace system board

3,1 Coin-cell battery failure

3,2 PCI, video card/chip failure

3,3 Recovery image not found

3,4 Recovery image found but invalid

3,5 Power-rail failure

3,6 System BIOS Flash incomplete

3,7 Management Engine (ME) error

Camera status light: Indicates whether the camera is in use.

• Solid white — Camera is in use.

• Off — Camera is not in use.

Caps Lock status light: Indicates whether Caps Lock is enabled or disabled.

• Solid white — Caps Lock enabled.

• Off — Caps Lock disabled.

Flashing BIOS (USB key)

Steps

1. Follow the procedure from step 1 to step 7 in "Flashing the BIOS" to download the latest BIOS setup program file.

2. Create a bootable USB drive. For more information see the knowledge base article SLN143196 at www.dell.com/support.

3. Copy the BIOS setup program file to the bootable USB drive.

4. Connect the bootable USB drive to the computer that needs the BIOS update.

5. Restart the computer and press F12 when the Dell logo is displayed on the screen.

6. Boot to the USB drive from the One Time Boot Menu.

7. Type the BIOS setup program filename and press Enter.

8. The BIOS Update Utility appears. Follow the instructions on the screen to complete the BIOS update.

70 Troubleshooting

Flashing the BIOS

About this task

You may need to flash (update) the BIOS when an update is available or when you replace the system board.

Follow these steps to flash the BIOS:

Steps

1. Turn on your computer.

2. Go to www.dell.com/support.

3. Click Product support, enter the Service Tag of your computer, and then click Submit.

NOTE: If you do not have the Service Tag, use the auto-detect feature or manually browse for your computer model.

4. Click Drivers & downloads > Find it myself.

5. Select the operating system installed on your computer.

6. Scroll down the page and expand BIOS.

7. Click Download to download the latest version of the BIOS for your computer.

8. After the download is complete, navigate to the folder where you saved the BIOS update file.

9. Double-click the BIOS update file icon and follow the instructions on the screen.

Backup media and recovery options

It is recommended to create a recovery drive to troubleshoot and fix problems that may occur with Windows. Dell proposes multiple

options for recovering Windows operating system on your Dell PC. For more information. see Dell Windows Backup Media and Recovery

Options.

WiFi power cycle

About this task

If your computer is unable to access the internet due to WiFi connectivity issues a WiFi power cycle procedure may be performed. The

following procedure provides the instructions on how to conduct a WiFi power cycle:

NOTE: Some ISPs (Internet Service Providers) provide a modem/router combo device.

Steps

1. Turn off your computer.

2. Turn off the modem.

3. Turn off the wireless router.

4. Wait for 30 seconds.

5. Turn on the wireless router.

6. Turn on the modem.

7. Turn on your computer.

Flea power release

About this task

Flea power is the residual static electricity that remains on the computer even after it has been powered off and the battery has been

removed. The following procedure provides the instructions on how to conduct flea power release:

Steps

1. Turn off your computer.

Troubleshooting 71

2. Disconnect the power adapter from your computer.

3. Press and hold the power button for 15 seconds to drain the flea power.

4. Connect the power adapter to your computer.

5. Turn on your computer.

72 Troubleshooting

Getting help

Topics:

•Contacting Dell

Contacting Dell

Prerequisites

NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice,

packing slip, bill, or Dell product catalog.

About this task

Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services

may not be available in your area. To contact Dell for sales, technical support, or customer service issues:

Steps

1. Go to Dell.com/support.

2. Select your support category.

3. Verify your country or region in the Choose a Country/Region drop-down list at the bottom of the page.

4. Select the appropriate service or support link based on your need.

Getting help 73

Table of Contents

DELL 9510 2in1 User Manual

Related Manuals