Table of Contents
- Dell Latitude E5470 Owner's Manual
- Working on your computer
- Removing and installing components
- Recommended tools
- Installing the Subscriber Identification Module (SIM) card
- Removing the Subscriber Identification Module (SIM) card
- Removing the base cover
- Installing the base cover
- Removing the battery
- Installing the battery
- Removing the hard drive assembly
- Removing the hard drive from the hard drive bracket
- Installing the hard drive into the hard drive bracket
- Installing the hard drive assembly
- Installing the optional M.2 SSD
- Removing the optional M.2 Solid State Drive (SSD)
- Installing the optional PCIe SSD
- Removing the optional PCIe SSD
- Removing the memory module
- Installing the memory module
- Removing the WLAN card
- Installing the WLAN card
- Removing the WWAN card
- Installing the WWAN card
- Removing the power connector port
- Installing the power connector port
- Removing the keyboard
- Installing the keyboard
- Removing the display assembly
- Installing the display assembly
- Removing the dock frame
- Installing the dock frame
- Removing the optional SmartCard reader board
- Installing the optional SmartCard reader board
- Removing the optional finger print reader board
- Installing the optional finger print reader board
- Removing the LED board
- Installing the LED board
- Removing the heat sink assembly
- Installing the heat sink assembly
- Removing the speakers
- Installing the speakers
- Removing the system board
- Installing the system board
- Removing the coin cell battery
- Installing the coin cell battery
- System setup options
- Boot Sequence
- Navigation keys
- System Setup overview
- Accessing System Setup
- General screen options
- System Configuration screen options
- Video screen options
- Security screen options
- Secure Boot screen options
- Intel Software Guard Extensions screen options
- Performance screen options
- Power Management screen options
- POST Behavior screen options
- Virtualization support screen options
- Wireless screen options
- Maintenance screen options
- System Log screen options
- Updating the BIOS
- System and setup password
- Technical specifications
- System specifications
- Processor specifications
- Memory specifications
- Storage specifications
- Audio specifications
- Video specifications
- Camera specifications
- Communication specifications
- Port and connector specifications
- Contactless smart card specifications
- Display specifications
- Keyboard specifications
- Touchpad specifications
- Battery specifications
- AC Adapter specifications
- Physical specifications
- Environmental specifications
- Diagnostics
- Contacting Dell
DELL E5470 User Manual
Displayed below is the user manual for E5470 by DELL which is a product in the Notebooks category. This manual has pages.
Related Manuals
Dell Latitude E5470
Owner's Manual
Regulatory Model: P62G
Regulatory Type: P62G001
Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use of your computer.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you
how to avoid the problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
Copyright © 2016 Dell Inc. All rights reserved. This product is protected by U.S. and international copyright and
intellectual property laws. Dell™ and the Dell logo are trademarks of Dell Inc. in the United States and/or other
jurisdictions. All other marks and names mentioned herein may be trademarks of their respective companies.
2016 - 05
Rev. A01
Contents
1 Working on your computer.................................................................................6
Safety instructions................................................................................................................................. 6
Before working inside your computer..................................................................................................7
Turning off your computer................................................................................................................... 7
After working inside your computer.....................................................................................................8
2 Removing and installing components..............................................................9
Recommended tools.............................................................................................................................9
Installing the Subscriber Identification Module (SIM) card.................................................................. 9
Removing the Subscriber Identification Module (SIM) card.............................................................. 10
Removing the base cover................................................................................................................... 10
Installing the base cover..................................................................................................................... 10
Removing the battery..........................................................................................................................10
Installing the battery............................................................................................................................ 11
Removing the hard drive assembly.....................................................................................................12
Removing the hard drive from the hard drive bracket.......................................................................12
Installing the hard drive into the hard drive bracket.......................................................................... 13
Installing the hard drive assembly.......................................................................................................14
Installing the optional M.2 SSD........................................................................................................... 14
Removing the optional M.2 Solid State Drive (SSD)...........................................................................14
Installing the optional PCIe SSD......................................................................................................... 14
Removing the optional PCIe SSD........................................................................................................15
Removing the memory module..........................................................................................................15
Installing the memory module............................................................................................................16
Removing the WLAN card...................................................................................................................16
Installing the WLAN card..................................................................................................................... 17
Removing the WWAN card..................................................................................................................17
Installing the WWAN card....................................................................................................................17
Removing the power connector port.................................................................................................18
Installing the power connector port...................................................................................................18
Removing the keyboard ..................................................................................................................... 18
Installing the keyboard........................................................................................................................ 19
Removing the display assembly......................................................................................................... 20
Installing the display assembly............................................................................................................21
Removing the dock frame...................................................................................................................21
Installing the dock frame.................................................................................................................... 22
Removing the optional SmartCard reader board.............................................................................. 22
Installing the optional SmartCard reader board................................................................................ 23
3
Removing the optional finger print reader board..............................................................................23
Installing the optional finger print reader board................................................................................24
Removing the LED board....................................................................................................................24
Installing the LED board......................................................................................................................25
Removing the heat sink assembly...................................................................................................... 25
Installing the heat sink assembly........................................................................................................ 26
Removing the speakers.......................................................................................................................26
Installing the speakers.........................................................................................................................27
Removing the system board............................................................................................................... 27
Installing the system board.................................................................................................................28
Removing the coin cell battery.......................................................................................................... 28
Installing the coin cell battery............................................................................................................ 29
3 System setup options.........................................................................................30
Boot Sequence....................................................................................................................................30
Navigation keys................................................................................................................................... 30
System Setup overview....................................................................................................................... 31
Accessing System Setup......................................................................................................................31
General screen options....................................................................................................................... 31
System Configuration screen options................................................................................................32
Video screen options.......................................................................................................................... 34
Security screen options...................................................................................................................... 34
Secure Boot screen options............................................................................................................... 36
Intel Software Guard Extensions screen options...............................................................................37
Performance screen options.............................................................................................................. 37
Power Management screen options.................................................................................................. 38
POST Behavior screen options...........................................................................................................40
Virtualization support screen options.................................................................................................41
Wireless screen options...................................................................................................................... 41
Maintenance screen options.............................................................................................................. 42
System Log screen options................................................................................................................ 42
Updating the BIOS ..............................................................................................................................43
System and setup password............................................................................................................... 43
Assigning a system password and setup password.....................................................................44
Deleting or changing an existing system and/or setup password..............................................44
4 Technical specifications....................................................................................45
System specifications..........................................................................................................................45
Processor specifications..................................................................................................................... 45
Memory specifications........................................................................................................................46
Storage specifications.........................................................................................................................46
Audio specifications............................................................................................................................46
4
Video specifications............................................................................................................................46
Camera specifications.........................................................................................................................47
Communication specifications...........................................................................................................47
Port and connector specifications..................................................................................................... 47
Contactless smart card specifications............................................................................................... 48
Display specifications..........................................................................................................................48
Keyboard specifications......................................................................................................................49
Touchpad specifications.....................................................................................................................49
Battery specifications..........................................................................................................................50
AC Adapter specifications...................................................................................................................50
Physical specifications.........................................................................................................................51
Environmental specifications.............................................................................................................. 51
5 Diagnostics...........................................................................................................53
Enhanced Pre-Boot System Assessment (ePSA) diagnostics............................................................53
Device status lights............................................................................................................................. 54
Battery status lights............................................................................................................................. 55
6 Contacting Dell...................................................................................................56
5
1
Working on your computer
Safety instructions
Use the following safety guidelines to help protect your computer from potential damage and to help to
ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes
that the following conditions exist:
• You have read the safety information that shipped with your computer.
• A component can be replaced or--if purchased separately--installed by performing the removal
procedure in reverse order.
WARNING: Disconnect all power sources before opening the computer cover or panels. After you
finish working inside the computer, replace all covers, panels, and screws before connecting to
the power source.
WARNING: Before working inside your computer, read the safety information that shipped with
your computer. For additional safety best practices information, see the Regulatory Compliance
Homepage at www.dell.com/regulatory_compliance
CAUTION: Many repairs may only be done by a certified service technician. You should only
perform troubleshooting and simple repairs as authorized in your product documentation, or as
directed by the online or telephone service and support team. Damage due to servicing that is
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions
that came with the product.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or
by periodically touching an unpainted metal surface, such as a connector on the back of the
computer.
CAUTION: Handle components and cards with care. Do not touch the components or contacts
on a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a
processor by its edges, not by its pins.
CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable
itself. Some cables have connectors with locking tabs; if you are disconnecting this type of cable,
press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep
them evenly aligned to avoid bending any connector pins. Also, before you connect a cable,
ensure that both connectors are correctly oriented and aligned.
NOTE: The color of your computer and certain components may appear differently than shown in
this document.
6
Before working inside your computer
To avoid damaging your computer, perform the following steps before you begin working inside the
computer.
1. Ensure that you follow the Safety instructions.
2. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.
3. Turn off your computer, see Turning off your computer.
CAUTION: To disconnect a network cable, first unplug the cable from your computer and
then unplug the cable from the network device.
4. Disconnect all the network cables from the computer.
5. Disconnect your computer and all attached devices from the electrical outlets.
6. Press and hold the power button while the computer is unplugged to ground the system board.
7. Remove the cover.
CAUTION: Before touching anything inside your computer, ground yourself by touching an
unpainted metal surface, such as the metal at the back of the computer. While you work,
periodically touch an unpainted metal surface to dissipate static electricity, which could
harm internal components.
Turning off your computer
CAUTION: To avoid losing data, save and close all open files and exit all open programs before
you turn off your computer.
1. Turning off your computer:
• In Windows 10 (using a touch enabled device or mouse):
1. Click or tap .
2. Click or tap and then click or touch Shut down.
• In Windows 8 (using a touch enabled device):
1. Swipe in from the right edge of the screen, opening the Charms menu and select Settings.
2. Tap and then tap Shut down
• In Windows 8 (using a mouse):
1. Point to upper-right corner of the screen and click Settings.
2. Click and then click Shut down.
• In Windows 7:
1. Click Start.
2. Click Shut Down.
2. Ensure that the computer and all attached devices are turned off. If your computer and attached
devices did not automatically turn off when you shut down your operating system, press and hold
the power button for about 6 seconds to turn them off.
7
After working inside your computer
After you complete any replacement procedure, ensure you connect any external devices, cards, and
cables before turning on your computer.
CAUTION: To avoid damage to the computer, use only the battery designed for this particular
Dell computer. Do not use batteries designed for other Dell computers.
1. Connect any external devices, such as a port replicator or media base, and replace any cards, such as
an ExpressCard.
2. Connect any telephone or network cables to your computer.
CAUTION: To connect a network cable, first plug the cable into the network device and then
plug it into the computer.
3. Replace the battery.
4. Replace the base cover.
5. Connect your computer and all attached devices to their electrical outlets.
6. Turn on your computer.
8
2
Removing and installing components
This section provides detailed information on how to remove or install the components from your
computer.
Recommended tools
The procedures in this document require the following tools:
• Small flat blade screwdriver
• Phillips #0 screwdriver
• Phillips #1 screwdriver
• Small plastic scribe
Installing the Subscriber Identification Module (SIM) card
1. Follow the procedure in Before working inside your computer.
2. Insert a paperclip or a SIM card removal tool into the pinhole to remove the SIM card tray [1].
3. Place the SIM card on the SIM card tray [2].
4. Push the SIM card tray into the slot until it clicks into place.
9
Removing the Subscriber Identification Module (SIM) card
CAUTION: Removing the SIM card when the computer is on may cause data loss or damage the
card. Ensure your computer is turned off or the network connections are disabled.
1. Insert a paperclip or a SIM card removal tool into the pinhole on the SIM card tray.
2. Remove the SIM card from the SIM card tray.
3. Push the SIM card tray into the slot until it clicks into place.
Removing the base cover
1. Follow the procedure in Before working inside your computer.
2. To remove the base cover:
a. Loosen the screws that secure the base cover to the computer [1].
b. Lift the base cover from the edge and remove it from the computer [2, 3].
NOTE: You may need a plastic scribe to lift the base cover from the edges.
Installing the base cover
1. Align the base cover with the screw holders on the computer.
2. Press the edges of the cover until it clicks into place.
3. Tighten the screws to secure the base cover to the computer.
4. Follow the procedure in After working inside your computer.
Removing the battery
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
3. To remove the battery:
10
a. Disconnect the battery cable from the connector on the system board [1].
b. Remove the screws that secure the battery to the computer [2].
c. Lift the battery away from the computer [3].
4. Unroute the cable from the routing channel [1] and remove the cable from the battery [2].
NOTE: This step is applicable only for a 4-cell battery.
Installing the battery
NOTE: If your computer supports a 6-cell battery, it will not support a hard drive.
1. Connect the battery cable to the connector on the battery.
2. Route the battery cable through the routing channel on the battery.
3. Insert the battery into the slot on the computer.
4. Tighten the screws to secure the battery to the computer.
11
5. Connect the battery cable to the connector on the system board.
6. Install the base cover.
7. Follow the procedure in After working inside your computer.
Removing the hard drive assembly
1. Follow the procedure in Before working inside your computer.
2. Remove the:
a. base cover
b. battery
3. To remove the hard drive assembly:
a. Disconnect the hard drive cable from the connector on the system board [1] .
b. Remove the screws that secure the hard drive assembly to the computer [2].
c. Lift the hard drive assembly away from the computer [3].
Removing the hard drive from the hard drive bracket
1. Follow the procedure in Before working inside your computer.
2. Remove the:
a. base cover
b. battery
c. hard drive assembly
3. Pull the hard drive cable to remove it from the connector.
12
4. Remove the screws that secure the hard drive bracket to the hard drive [1] and lift the hard drive from
the hard drive bracket [2].
Installing the hard drive into the hard drive bracket
1. Align the screw holders on the hard drive with the screws on the hard drive bracket.
2. Insert the hard drive into the hard drive bracket.
3. Tighten the screws to secure the hard drive to the hard drive bracket.
4. Install the:
a. hard drive assembly
b. battery
c. base cover
13
5. Follow the procedure in After working inside your system.
Installing the hard drive assembly
1. Insert the hard drive assembly into the slot on the computer.
2. Tighten the screws to secure the hard drive assembly to the computer.
3. Connect the hard drive cable to the connector on the hard drive and on the system board.
4. Install the:
a. battery
b. base cover
5. Follow the procedures in After working inside your system.
Installing the optional M.2 SSD
1. Insert the SSD into the connector on the computer.
2. Tighten the screw to secure the SSD to the computer.
3. Install the:
a. battery
b. base cover
4. Follow the procedure in After working inside your computer.
Removing the optional M.2 Solid State Drive (SSD)
1. Follow the procedure in Before working inside your computer.
2. Remove the:
a. base cover
b. battery
3. To remove the SSD:
a. Remove the screw that secures the SSD to the computer [1].
b. Slide and lift the SSD from the computer [2].
Installing the optional PCIe SSD
1. Insert the SSD clip into the slot on the computer.
2. Tighten the screw to secure the SSD clip to the computer.
14
3. Insert the SSD into the connector on the computer.
4. Place the SSD bracket over the SSD and tighten the screws to secure it to the computer.
5. Install the:
a. battery
b. base cover
6. Follow the procedure in After working inside your computer.
Removing the optional PCIe SSD
1. Follow the procedure in Before working inside your computer.
2. Remove the:
a. base cover
b. battery
3. To remove the PCIe SSD:
a. Remove the screws that secure the SSD bracket to the SSD [1].
b. Remove the SSD bracket [2].
c. Remove the SSD from the computer [3].
Removing the memory module
1. Follow the procedure in Before working inside your computer.
2. Remove the:
a. base cover
b. battery
3. Pull the clips securing the memory module until the memory module pops up [1].
4. Remove the memory module from the system board [2].
15
Installing the memory module
1. Insert the memory module into the memory module socket until the clips secure the memory
module.
2. Install the:
a. battery
b. base cover
3. Follow the procedures in After working inside your computer.
Removing the WLAN card
1. Follow the procedure in Before working inside your computer.
2. Remove the:
a. base cover
b. battery
3. To remove the WLAN card:
a. Remove the screw that secures the metal bracket to the WLAN card [1].
b. Remove the metal bracket [2].
c. Disconnect the WLAN cables from the connectors on the WLAN card [3].
d. Unroute the WLAN cables from the routing channel.
e. Remove the WLAN card from the computer [4].
16
Installing the WLAN card
1. Insert the WLAN card into the slot on the computer.
2. Route the WLAN cables through the routing channel.
3. Connect the WLAN cables to the connectors on the WLAN Card.
4. Place the metal bracket and tighten the screw to secure it to the computer.
5. Install the:
a. battery
b. base cover
6. Follow the procedure in After working inside your system.
Removing the WWAN card
1. Follow the procedure in Before working inside your computer.
2. Remove the:
a. base cover
b. battery
3. To remove the WWAN card:
a. Remove the screw that secures the WWAN card [1].
b. Disconnect the WWAN cables from the connectors on the WWAN card [2].
c. Unroute the WWAN cables from the routing channel.
d. Remove the WWAN card from the computer [3].
Installing the WWAN card
1. Insert the WWAN card into the slot on the computer.
2. Route the WWAN cables through the routing channel.
3. Connect the WWAN cables to the connectors on the WWAN card.
4. Tighten the screw to secure the WWAN card to the computer
5. Install the:
a. battery
b. base cover
6. Follow the procedure in After working inside your computer.
17
Removing the power connector port
1. Follow the procedure in Before working inside your computer.
2. Remove the:
a. base cover
b. battery
c. dock frame
3. To remove the power connector port:
a. Remove the screws to release the metal bracket on the power connector port [1].
b. Lift the metal bracket from the computer [2].
c. Remove the power connector port from the computer [3].
d. Disconnect the power connector port cable from the computer [4].
Installing the power connector port
1. Insert the power connector port into the slot on the computer.
2. Place the metal bracket on the power connector port.
3. Tighten the screw to secure the power connector port to the computer.
4. Route the power connector port cable through the routing channels.
5. Connect the power connector port cable to the connector on the system board.
6. Install the:
a. dock frame
b. battery
c. base cover
7. Follow the procedure in After working inside your computer.
Removing the keyboard
1. Follow the procedure in Before working inside your computer.
2. Remove the:
18
a. base cover
b. battery
3. Disconnect the keyboard cables from the connectors on the system board [1, 2].
4. To remove the keyboard:
a. Using a plastic scribe, lift the keyboard trim from the edges to release it from the keyboard [1, 2,
3].
b. Remove the screws that secure the keyboard to the computer [4].
c. Lift the keyboard from computer [5].
Installing the keyboard
1. Align the keyboard with the screw holders on the computer.
2. Tighten the screws to secure the keyboard to the computer.
3. Align the keyboard trim with the tabs on the computer and press it until it clicks into place
4. Connect the keyboard cables to the connectors on the system board.
5. Install the:
a. battery
b. base cover
6. Follow the procedure in After working inside your system.
19
Removing the display assembly
1. Follow the procedure in Before working inside your computer.
2. Remove the:
a. base cover
b. battery
c. WLAN
d. WWAN
3. To remove the display hinge brackets:
a. Remove the screw that secures the display hinge bracket to the computer [1].
b. Remove the display hinge bracket from the computer [2].
c. Remove the screws that secure the display assembly to the computer [3].
4. To disconnect display cable and remove the display assembly:
a. Remove the screw that secures the display cable bracket to the computer [1].
b. Remove the display cable bracket to access the display cable [2].
c. Disconnect the display cable from the system board [3].
d. Release the antenna cables and display cable from the routing channel [4].
e. Remove the screws that secure the display assembly and lift the display assembly to remove it
from the computer [5].
20
Installing the display assembly
1. Place the display assembly to align with the screw holders on the computer.
2. Tighten the screws to secure the display assembly to the computer.
3. Route the display cable through the routing channel and route the antenna cables by pushing it
through the hole.
4. Connect the antenna cables and display cable to the connectors.
5. Place the display cable bracket over the connector and tighten the screw to secure the display cable
to the computer.
6. Place the display hinge bracket and tighten the screw to secure it to the computer.
7. Install the:
a. WLAN
b. WWAN
c. battery
d. base cover
8. Follow the procedure in After working inside your computer.
Removing the dock frame
1. Follow the procedure in Before working inside your computer.
2. Remove the:
a. base cover
b. battery
c. hard drive assembly or M.2 SSD or PCIe SSD
d. WLAN card
e. WWAN card
3. To remove the dock frame connectors:
a. Remove the screws that secure the dock frame to the computer [1].
b. Remove the screw and lift the SSD plate from the computer [2, 3].
NOTE: Step 3b is required only if the PCIe SSD card is removed.
c. Disconnect the keyboard cables [4, 5].
4. To remove the dock frame:
21
a. Remove the screw and lift the metal bracket [1,2].
b. Disconnect the eDP cable [3].
c. Remove the screws that secure the dock frame to the computer [4].
d. Lift the dock frame from the computer [5].
Installing the dock frame
1. Place the dock frame on the computer and tighten the screws.
2. Connect the eDP cable.
3. Place the metal bracket and tighten the screw.
4. Connect the keyboard cable.
5. Place the SSD plate and tighten the screw to secure it.
NOTE: Step 5 is required only if the PCIe SSD card is removed.
6. Tighten the screws to secure the dock frame to the computer.
7. Install the:
a. WWAN card
b. WLAN card
c. hard drive assembly or M.2 SSD or PCIe SSD
d. battery
e. base cover
8. Follow the procedure in After working inside your system.
Removing the optional SmartCard reader board
1. Follow the procedure in Before working inside your computer.
2. Remove the:
a. base cover
b. battery
c. hard drive assembly or M.2 SSD or PCIe SSD
d. dock frame
3. To remove the SmartCard reader board:
a. Disconnect the SmartCard reader board cable from the USH board [1, 2].
b. Peel the cable to release from the adhesive.
22
c. Remove the screws that secure the SmartCard reader board to the computer [3].
d. Lift the SmartCard reader board from the computer [4].
Installing the optional SmartCard reader board
1. Insert the SmartCard reader board into the slot on the computer.
2. Tighten the screws to secure the SmartCard reader board to the computer.
3. Connect the SmartCard reader cable to the connector on the USH board.
4. Install the:
a. dock frame
b. hard drive assembly or M.2 SSD or PCIe SSD
c. battery
d. base cover
5. Follow the procedure in After working inside your computer.
Removing the optional finger print reader board
1. Follow the procedure in Before working inside your computer.
2. Remove the:
a. base cover
b. battery
c. hard drive assembly or M.2 SSD or PCIe SSD
d. dock frame
e. WLAN card
f. WWAN card
3. To remove the finger print reader board:
a. Remove the screw to release the metal bracket that secures the finger print reader board to the
computer [1].
b. Lift the metal bracket from the computer [2].
c. Disconnect the finger print reader cable from the finger print reader board [3] [4].
d. Lift the finger print reader board from the computer [5].
4. To remove the finger print reader board:
23
a. Disconnect the finger print reader cable from the finger print reader board [1, 2].
b. Remove the screw that secure the finger print reader board to the computer [3].
c. Lift the finger print reader board from the computer [4].
Installing the optional finger print reader board
1. Insert the finger print reader board into the slot on the computer.
2. Connect the finger print reader cable to the finger print reader board.
3. Place the metal bracket on the finger print reader board and tighten the screw to secure the finger
print reader board.
4. Install the:
a. hard drive assembly or M.2 SSD or PCIe SSD
b. dock frame
c. WLAN card
d. WWAN card
e. battery
f. base cover
5. Follow the procedure in After working inside your system.
Removing the LED board
1. Follow the procedure in Before working inside your computer.
2. Remove the:
a. base cover
b. battery
c. hard drive assembly or M.2 SSD or PCIe SSD
d. dock frame
3. To remove the LED board:
a. Disconnect the LED board cable from the connector on the LED board [1, 2].
b. Remove the screw that secures the LED board to the computer [3].
c. Lift the LED board from the computer [4].
24
Installing the LED board
1. Insert the LED board into the slot on the computer.
2. Tighten the screw that secures the LED board to the computer.
3. Connect the LED board cable to the connector on the LED board.
4. Install the:
a. dock frame
b. hard drive assembly or M.2 SSD or PCIe SSD
c. battery
d. base cover
5. Follow the procedure in After working inside your computer.
Removing the heat sink assembly
1. Follow the procedure in Before working inside your computer.
2. Remove the:
a. base cover
b. battery
c. hard drive assembly or M.2 SSD or PCIe SSD
d. WLAN
e. WWAN
f. dock frame
3. To remove the heat sink:
a. Disconnect the fan cable [1].
b. Remove the screws that secure the heat sink assembly to the system board [2, 3, 4, 5, 6, 7].
c. Lift the heat sink assembly from the system board [8].
25
Installing the heat sink assembly
1. Place the heat sink assembly on the system board and align it with the screw holders.
2. Tighten the screws to secure the heat sink assembly to the system board.
3. Connect the fan cable to the connector on the system board.
4. Install the:
a. dock frame
b. WWAN
c. WLAN
d. hard drive assembly or M.2 SSD or PCIe SSD
e. battery
f. base cover
5. Follow the procedure in After working inside your computer.
Removing the speakers
1. Follow the procedure in Before working inside your computer.
2. Remove the:
a. base cover
b. battery
c. memory module
d. hard drive assembly or M.2 SSD or PCIe SSD
e. dock frame
3. To remove the speaker:
a. Disconnect the speaker cable [1].
b. Disconnect the LED board cable[2, 3] from the LED board.
c. Unroute the cables from the retention clips on the computer.
d. Lift the speaker from the computer [4].
26
Installing the speakers
1. Place the speakers into the slots on the computer.
2. Route the speaker cable through the retention clips through the routing channel.
3. Connect the speaker cable to the connector on the system board.
4. Install the:
a. dock frame
b. WLAN
c. WWAN
d. hard drive assembly or M.2 SSD or PCIe SSD
e. battery
f. base cover
5. Follow the procedure in After working inside your computer.
Removing the system board
1. Follow the procedure in Before working inside your computer.
2. Remove the:
a. base cover
b. battery
c. memory
d. hard drive assembly or M.2 SSD or PCIe SSD
e. keyboard
f. dock frame
g. WLAN
h. WWAN
i. heat sink assembly
j. power connector port
3. To remove the system board:
a. Lift the latch and disconnect the speaker cable, touch pad and system board cable from the
computer [1, 2, 3].
b. Disconnect the eDP cable from the system board [4].
c. Remove the screws that secures system board to the computer [5].
d. Lift the system board from the computer [6].
27
Installing the system board
1. Align the system board with the screw holders on the computer.
2. Tighten the screws to secure the system board to the computer.
3. Connect the speaker cable to its connector on the system and route the cable through its routing
channels.
4. Connect the speaker, power connector and coin cell battery cables to the connectors on the system
board:
5. Install the:
a. power connector port
b. WLAN
c. heat sink assembly
d. WWAN
e. dock frame
f. hard drive assembly or M.2 SSD or PCIe SSD
g. keyboard
h. memory module
i. battery
j. base cover
6. Follow the procedure in After working inside your computer.
Removing the coin cell battery
1. Follow the procedure in Before working inside your computer.
2. Remove the:
a. base cover
b. battery
c. memory
d. hard drive assembly or M.2 SSD or PCIe SSD
e. keyboard
f. dock frame
g. WLAN
h. WWAN
i. heat sink assembly
28
j. power connector port
k. system board
NOTE: Coin cell battery is located behind the system board.
3. To remove the coin cell battery:
a. Disconnect the coin cell battery cable from the connector on the system board [1].
b. Lift the coin cell battery to release it from the adhesive and remove it from the system board [2].
Installing the coin cell battery
1. Place the coin cell battery into the slot on the system board.
2. Connect the coin cell battery cable to the connector on the system board.
3. Install the:
a. system board
b. power connector port
c. WLAN
d. heat sink assembly
e. WWAN
f. dock frame
g. hard drive assembly or M.2 SSD or PCIe SSD
h. keyboard
i. memory module
j. battery
k. base cover
4. Follow the procedure in After working inside your computer.
29
3
System setup options
NOTE: Depending on the computer and its installed devices, the items listed in this section may or
may not appear.
Boot Sequence
Boot Sequence allows you to bypass the System Setup‐defined boot device order and boot directly to a
specific device (for example: optical drive or hard drive). During the Power-on Self Test (POST), when the
Dell logo appears, you can:
• Access System Setup by pressing F2 key
• Bring up the one-time boot menu by pressing F12 key
The one-time boot menu displays the devices that you can boot from including the diagnostic option.
The boot menu options are:
• Removable Drive (if available)
• STXXXX Drive
NOTE: XXX denotes the SATA drive number.
• Optical Drive
• Diagnostics
NOTE: Choosing Diagnostics, will display the ePSA diagnostics screen.
The boot sequence screen also displays the option to access the System Setup screen.
Navigation keys
The following table displays the system setup navigation keys.
NOTE: For most of the System Setup options, changes that you make are recorded but do not take
effect until you restart the system.
Table 1. Navigation keys
Keys Navigation
Up arrow Moves to the previous field.
Down arrow Moves to the next field.
Enter Allows you to select a value in the selected field (if applicable) or follow the link in
the field.
Spacebar Expands or collapses a drop‐down list, if applicable.
30
Keys Navigation
Tab Moves to the next focus area.
NOTE: For the standard graphics browser only.
Esc Moves to the previous page till you view the main screen. Pressing Esc in the main
screen displays a message that prompts you to save any unsaved changes and
restarts the system.
F1 Displays the System Setup help file.
System Setup overview
System Setup allows you to:
• Change the system configuration information after you add, change, or remove any hardware in your
computer.
• Set or change a user-selectable option such as the user password.
• Read the current amount of memory or set the type of hard drive installed.
Before you use System Setup, it is recommended that you write down the System Setup screen
information for future reference.
CAUTION: Unless you are an expert computer user, do not change the settings for this program.
Certain changes can cause your computer to work incorrectly.
Accessing System Setup
1. Turn on (or restart) your computer.
2. After the white Dell logo appears, press F2 immediately.
The System Setup page is displayed.
NOTE: If you wait too long and the operating system logo appears, wait until you see the
desktop. Then, shut down or restart your computer and try again.
NOTE: After the Dell logo appears, you can also press F12 and then select BIOS setup.
General screen options
This section lists the primary hardware features of your computer.
Option Description
System
Information • System Information: Displays BIOS Version, Service Tag, Asset Tag, Ownership
Tag, Ownership Date, Manufacture Date, and the Express Service Code.
• Memory Information: Displays Memory Installed, Memory Available, Memory
Speed, Memory Channels Mode, Memory Technology, DIMM A Size, DIMM B
Size.
• Processor Information: Displays Processor Type, Core Count, Processor ID,
Current Clock Speed, Minimum Clock Speed, Maximum Clock Speed,
Processor L2 Cache, Processor L3 Cache, HT Capable, and 64-Bit technology.
• Device Information: Displays Primary Hard Drive, SATA-0, M.2PCIe SSD-0, Dock
eSATA Device, LOM MAC Address, Video Controller, Video BIOS Version, Video
31
Option Description
Memory, Panel Type, Native Resolution, Audio Controller, WiFi Device, WiGig
Device, Cellular Device, Bluetooth Device.
Battery
Information
Displays the battery status and the type of AC adapter connected to the computer.
Boot Sequence Boot Sequence Allows you to change the order in which the computer
attempts to find an operating system. The options are:
• Windows Boot Manager
• UEFI: Hard drive details
Boot List Options Allows you to change the boot list option:
• Legacy
• UEFI (enabled by default)
Advanced Boot
Options
This option allows you the legacy option ROMs to load. By default, the Enable
Legacy Option ROMs is disabled.
Date/Time Allows you to change the date and time.
System Configuration screen options
Option Description
Integrated NIC Allows you to configure the integrated network controller. The options are:
• Disabled
• Enabled
• Enabled w/PXE: This option is enabled by default.
Parallel Port Allows you to configure the parallel port on the docking station. The options are:
• Disabled
• AT: This option is enabled by default.
• PS2
• ECP
Serial Port Allows you to configure the integrated serial port. The options are:
• Disabled
• COM1: This option is enabled by default.
• COM2
• COM3
• COM4
32
Option Description
SATA Operation Allows you to configure the internal SATA hard-drive controller. The options are:
• Disabled
• AHCI
• RAID On: This option is enabled by default.
Drives Allows you to configure the SATA drives on board. All drives are enabled by default.
The options are:
• SATA-0
• SATA-1
• SATA-2
• M.2 PCIe SSD-0
SMART Reporting This field controls whether hard drive errors for integrated drives are reported
during system startup. This technology is part of the SMART (Self Monitoring
Analysis and Reporting Technology) specification. This option is disabled by default.
• Enable SMART Reporting
USB Configuration This field configures the integrated USB controller. If Boot Support is enabled, the
system is allowed to boot any type of USB Mass Storage Devices (HDD, memory
key, floppy).
If USB port is enabled, device attached to this port is enabled and available for OS.
If USB port is disabled, the OS cannot see any device attached to this port.
The options are:
• Enable USB Boot Support (by default enable)
• Enable External USB Port (by default enable)
USB PowerShare This field configures the USB PowerShare feature behavior. This option allows you
to charge external devices using the stored system battery power through the USB
PowerShare port.
Audio This field enables or disables the integrated audio controller. By default, the Enable
Audio option is selected. The options are:
• Enable Microphone (by default enable)
• Enable Internal Speaker (by default enable)
Keyboard
Illumination
This field lets you choose the operating mode of the keyboard illumination feature.
The keyboard brightness level can be set from 0% to 100%. The options are:
• Disabled
• Dim
• Bright (enabled by default)
33
Option Description
Keyboard
Backlight with AC
The Keyboard Backlight with AC option does not affect the main keyboard
illumination feature. Keyboard Illumination will continue to support the various
illumination levels. This field has an effect when the backlight is enabled.
Touchscreen This option controls to enabled or disabled the touchscreen.
Unobtrusive Mode This option, when enabled, pressing Fn+F7 turns off all light and sound emissions
in the system. To resume normal operation, press Fn+F7 again. This option is
disabled by default.
Miscellaneous
Devices
Allows you to enable or disable the following devices:
• Enable Camera (enabled by default)
• SD Card Read Only
• Enable Hard Drive Free Fall Protection (enabled by default)
• Enable Media Card
• Disable Media Card
NOTE: All devices are enabled by default.
Video screen options
Option Description
LCD Brightness Allows you to set the display brightness depending up on the power source (On
Battery and On AC).
NOTE: The video setting will be visible only when a video card is installed into the system.
Security screen options
Option Description
Admin Password Allows you to set, change, or delete the administrator (admin) password.
NOTE: You must set the admin password before you set the system or hard
drive password. Deleting the admin password automatically deletes the system
password and the hard drive password.
NOTE: Successful password changes take effect immediately.
Default setting: Not set
System Password Allows you to set, change or delete the system password.
NOTE: Successful password changes take effect immediately.
Default setting: Not set
34
Option Description
Internal HDD-0
Password
Allows you to set, change or delete the system’s internal hard disk’s password.
Default setting: Not set
Strong Password Allows you to enforce the option to always set strong passwords.
Default Setting: Enable Strong Password is not selected.
NOTE: If Strong Password is enabled, Admin and System passwords must
contain at least one uppercase character, one lowercase character and be at
least 8 characters long.
Password
Configuration
Allows you to determine the minimum and maximum length of Administrator and
System passwords.
Password Bypass Allows you to enable or disable the permission to bypass the System and the
Internal HDD password, when they are set. The options are:
• Disabled
• Reboot bypass
Default setting: Disabled
Password Change Allows you to enable the disable permission to the System and Hard Drive
passwords when the admin password is set.
Default setting: Allow Non-Admin Password Changes is selected.
Non-Admin Setup
Changes
Allows you to determine whether changes to the setup options are allowed when
an Administrator Password is set. If disabled the setup options are locked by the
admin password.
TPM 1.2 Security Allows you to enable the Trusted Platform Module (TPM) during POST. The options
are:
• TPM On (enabled by default)
• Clear
• PPI Bypass for Enabled Commands
• PPI Bypass for Disabled Commands
• Disabled
• Enabled
Computrace Allows you to activate or disable the optional Computrace software The options
are:
• Deactivate
• Disable
• Activate
NOTE: The Activate and Disable options will permanently activate or disable
the feature and no further changes will be allowed
35
Option Description
Default setting: Deactivate
CPU XD Support Allows you to enable the Execute Disable mode of the processor.
Enable CPU XD Support (default)
OROM Keyboard
Access
Allows you to set an option to enter the Option ROM Configuration screens using
hotkeys during boot. The options are:
• Enable
• One Time Enable
• Disable
Default setting: Enable
Admin Setup
Lockout
Allows you to prevent users from entering the setup when an Administrator
password is set.
Default Setting: Enable Admin Setup Lockout is not selected.
Secure Boot screen options
Option Description
Secure Boot
Enable
This option enables or disables the Secure Boot feature.
• Disabled
• Enabled
Default setting: Enabled.
Expert Key
Management
Allows you to manipulate the security key databases only if the system is in Custom
Mode. The Enable Custom Mode option is disabled by default. The options are:
• PK
• KEK
• db
• dbx
If you enable the Custom Mode, the relevant options for PK, KEK, db, and dbx
appear. The options are:
•Save to File—Saves the key to a user-selected file
•Replace from File—Replaces the current key with a key from a user-selected
file
•Append from File—Adds a key to the current database from a user-selected file
•Delete—Deletes the selected key
•Reset All Keys—Resets to default setting
36
Option Description
•Delete All Keys—Deletes all the keys
NOTE: If you disable the Custom Mode, all the changes made will be erased
and the keys will restore to default settings.
Intel Software Guard Extensions screen options
Option Description
Intel SGX Enable This field specifies you to provide a secured environment for running code/storing
sensitive information in the context of the main OS. The options are:
• Disabled
• Enabled
Default setting: Disabled
Enclave Memory
Size
This option sets SGX Enclave Reserve Memory Size. The options are:
• 32 MB
• 64 MB
• 128 MB
Performance screen options
Option Description
Multi Core
Support
This field specifies whether the process has one or all cores enabled. The
performance of some applications improves with the additional cores. This option
is enabled by default. Allows you to enable or disable multi-core support for the
processor. The installed processor supports four cores. If you enable Multi Core
Support, four cores are enabled. If you disable Multi Core Support, one core is
enabled.
• Enable Multi Core Support
Default setting: The option is enabled.
Intel SpeedStep Allows you to enable or disable the Intel SpeedStep feature.
• Enable Intel SpeedStep
Default setting: The option is enabled.
C-States Control Allows you to enable or disable the additional processor sleep states.
• C states
37
Option Description
Default setting: The option is enabled.
Intel TurboBoost Allows you to enable or disable the Intel TurboBoost mode of the processor.
• Enable Intel TurboBoost
Default setting: The option is enabled.
Hyper-Thread
Control
Allows you to enable or disable the Hyper-Threading in the processor.
• Disabled
• Enabled
Default setting: Enabled.
Power Management screen options
Option Description
AC Behavior Allows you to enable or disable the computer from turning on automatically when
an AC adapter is connected.
Default setting: Wake on AC is not selected.
Auto On Time Allows you to set the time at which the computer must turn on automatically. The
options are:
• Disabled
• Every Day
• Weekdays
• Select Days
Default setting: Disabled
USB Wake
Support
Allows you to enable USB devices to wake the system from Standby.
NOTE: This feature is only functional when the AC power adapter is
connected. If the AC power adapter is removed during Standby, the system
setup removes power from all the USB ports to conserve battery power.
• Enable USB Wake Support
Default setting: The option is disabled.
Wireless Radio
Control
Allows you to enable or disable the feature that automatically switches from wired
or wireless networks without depending on the physical connection.
• Control WLAN Radio
• Control WWAN Radio
38
Option Description
Default setting: The option is disabled.
Wake on LAN/
WLAN
Allows you to enable or disable the feature that powers on the computer from the
Off state when triggered by a LAN signal.
• Disabled
• LAN Only
• WLAN Only
• LAN or WLAN
Default setting: Disabled
Block Sleep This option lets you block entering to sleep (S3 state) in operating system
environment.
Block Sleep (S3 state)
Default setting: This option is disabled
Peak Shift This option enables you to minimize the AC power consumption during the peak
power times of day. After you enable this option, your system runs only in battery
even if the AC is attached.
Dock Support on
Battery
This option allows you to use the docking station when AC power is absent but
only when the battery is above a certain charge percentage. The percentage may
change per battery and per platform.
• Dock Support on Battery
Default setting: Disabled
Advanced Battery
Charge
Configuration
This option enables you to maximize the battery health. By enabling this option,
your system uses the standard charging algorithm and other techniques, during the
non-work hours to improve the battery health.
Disabled
Default setting: Disabled
Primary Battery
Charge
Configuration
Allows you to select the charging mode for the battery. The options are:
• Adaptive
• Standard — Fully charges your battery at a standard rate.
• ExpressCharge — The battery charges over a shorter period of time using Dell’s
fast charging technology. This option is enabled by default.
• Primarily AC use
• Custom
If Custom Charge is selected, you can also configure Custom Charge Start and
Custom Charge Stop.
39
Option Description
NOTE: All charging mode may not be available for all the batteries. To enable
this option, disable the Advanced Battery Charge Configuration option.
POST Behavior screen options
Option Description
Adapter Warnings Allows you to enable or disable the system setup (BIOS) warning messages when
you use certain power adapters.
Default setting: Enable Adapter Warnings
Keypad
(Embedded)
Allows you to choose one of two methods to enable the keypad that is embedded
in the internal keyboard.
• Fn Key Only: This option is enabled by default.
• By Numlock
NOTE: When setup is running, this option has no effect. Setup works in Fn Key
Only mode.
Mouse/Touchpad Allows you to define how the system handles mouse and touch pad input. The
options are:
• Serial Mouse
• PS2 Mouse
• Touchpad/PS-2 Mouse: This option is enabled by default.
Numlock Enable Allows you to enable the Numlock option when the computer boots.
Enable Network. This option is enabled by default.
Fn Key Emulation Allows you to set the option where the Scroll Lock key is used to simulate the Fn
key feature.
Enable Fn Key Emulation (default)
Fn Lock Options Allows you to let hot key combinations Fn + Esc toggle the primary behavior of F1–
F12, between their standard and secondary functions. If you disable this option, you
cannot toggle dynamically the primary behavior of these keys. The available
options are:
• Fn Lock. This option is selected by default.
• Lock Mode Disable/Standard
• Lock Mode Enable/Secondary
MEBx Hotkey Allows you to specify whether the MEBx Hotkey function should enable, during the
system boot.
40
Option Description
Default Setting: Enable MEBx Hotkey
Fastboot Allows you to speed up the boot process by bypassing some of the compatibility
steps. The options are:
• Minimal
• Thorough (default)
• Auto
Extended BIOS
POST Time
Allows you to create an additional preboot delay. The options are:
• 0 seconds. This option is enabled by default.
• 5 seconds
• 10 seconds
Virtualization support screen options
Option Description
Virtualization Allows you to enable or disable the Intel Virtualization Technology.
Enable Intel Virtualization Technology (default).
VT for Direct I/O Enables or disables the Virtual Machine Monitor (VMM) from utilizing the additional
hardware capabilities provided by Intel® Virtualization technology for direct I/O.
Enable VT for Direct I/O - enabled by default.
Trusted Execution This option specifies whether a Measured Virtual Machine Monitor (MVMM) can
utilize the additional hardware capabilities provided by Intel Trusted Execution
Technology. The TPM Virtualization Technology, and Virtualization technology for
direct I/O must be enabled to use this feature.
Trusted Execution - disabled by default.
Wireless screen options
Option Description
Wireless Switch Allows to set the wireless devices that can be controlled by the wireless switch. The
options are:
• WWAN
• GPS (on WWAN Module)
• WLAN/WiGig
• Bluetooth
41
Option Description
All the options are enabled by default.
NOTE: For WLAN and WiGig enable or disable controls are tied together and
they cannot be enabled or disabled independently.
Wireless Device
Enable
Allows you to enable or disable the internal wireless devices.
• WWAN/GPS
• WLAN/WiGig
• Bluetooth
All the options are enabled by default.
Maintenance screen options
Option Description
Service Tag Displays the Service Tag of your computer.
Asset Tag Allows you to create a system asset tag if an asset tag is not already set. This option
is not set by default.
BIOS Downgrade This controls flashing of the system firmware to previous revisions.
Data Wipe This field allows users to erase the data securely from all internal storage devices.
The following is list of devices affected:
• Internal HDD
• Internal SDD
• Internal mSATA
• Internal eMMC
BIOS Recovery This field allows you to recover from certain corrupted BIOS conditions from a
recover file on the user primary hard drive or an external USB key.
• BIOS Recovery from Hard Drive (enabled by default)
System Log screen options
Option Description
BIOS Events Allows you to view and clear the System Setup (BIOS) POST events.
Thermal Events Allows you to view and clear the System Setup (Thermal) events.
Power Events Allows you to view and clear the System Setup (Power) events.
42
Updating the BIOS
It is recommended to update your BIOS (System Setup), on replacing the system board or if an update is
available. For laptops, ensure that your computer battery is fully charged and connected to a power
outlet
1. Restart the computer.
2. Go to Dell.com/support.
3. Enter the Service Tag or Express Service Code and click Submit.
NOTE: To locate the Service Tag, click Where is my Service Tag?
NOTE: If you cannot find your Service Tag, click Detect My Product. Proceed with the
instructions on screen.
4. If you are unable to locate or find the Service Tag, click the Product Category of your computer.
5. Choose the Product Type from the list.
6. Select your computer model and the Product Support page of your computer appears.
7. Click Get drivers and click View All Drivers.
The Drivers and Downloads page opens.
8. On the Drivers and Downloads screen, under the Operating System drop-down list, select BIOS.
9. Identify the latest BIOS file and click Download File.
You can also analyze which drivers need an update. To do this for your product, click Analyze
System for Updates and follow the instructions on the screen.
10. Select your preferred download method in the Please select your download method below window,
click Download File.
The File Download window appears.
11. Click Save to save the file on your computer.
12. Click Run to install the updated BIOS settings on your computer.
Follow the instructions on the screen.
NOTE: It is recommended not to update the BIOS version for more than 3 revisions. For example: If
you want to update the BIOS from 1.0 to 7.0, then install version 4.0 first and then install version 7.0.
System and setup password
You can create a system password and a setup password to secure your computer.
Password type Description
System password Password that you must enter to log on to your system.
Setup password Password that you must enter to access and make changes to the BIOS settings of
your computer.
CAUTION: The password features provide a basic level of security for the data on your computer.
CAUTION: Anyone can access the data stored on your computer if it is not locked and left
unattended.
NOTE: Your computer is shipped with the system and setup password feature disabled.
43
Assigning a system password and setup password
You can assign a new System Password and/or Setup Password or change an existing System Password
and/or Setup Password only when Password Status is Unlocked. If the Password Status is Locked, you
cannot change the System Password.
NOTE: If the password jumper is disabled, the existing System Password and Setup Password are
deleted and you need not provide the system password to log on to the computer.
To enter the system setup, press F2 immediately after a power-on or re-boot.
1. In the System BIOS or System Setup screen, select System Security and press Enter.
The System Security screen appears.
2. In the System Security screen, verify that Password Status is Unlocked.
3. Select System Password , enter your system password, and press Enter or Tab.
Use the following guidelines to assign the system password:
• A password can have up to 32 characters.
• The password can contain the numbers 0 through 9.
• Only lower case letters are valid, upper case letters are not allowed.
• Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).
Re-enter the system password when prompted.
4. Type the system password that you entered earlier and click OK.
5. Select Setup Password, type your system password and press Enter or Tab.
A message prompts you to re-type the setup password.
6. Type the setup password that you entered earlier and click OK.
7. Press Esc and a message prompts you to save the changes.
8. Press Y to save the changes.
The computer reboots.
Deleting or changing an existing system and/or setup password
Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or change
the existing System and/or Setup password. You cannot delete or change an existing System or Setup
password, if the Password Status is Locked.
To enter the System Setup, press F2 immediately after a power-on or reboot.
1. In the System BIOS or System Setup screen, select System Security and press Enter.
The System Security screen is displayed.
2. In the System Security screen, verify that Password Status is Unlocked.
3. Select System Password, alter or delete the existing system password and press Enter or Tab.
4. Select Setup Password, alter or delete the existing setup password and press Enter or Tab.
NOTE: If you change the System and/or Setup password, re-enter the new password when
promoted. If you delete the System and/or Setup password, confirm the deletion when
promoted.
5. Press Esc and a message prompts you to save the changes.
6. Press Y to save the changes and exit from System Setup.
The computer reboots.
44
4
Technical specifications
NOTE: Offerings may vary by region. For more information regarding the configuration of your
computer in:
• Windows 10, click or tap Start → Settings → System → About.
• Windows 8.1 and Windows 8, click or tap Start → PC Settings → PC and devices → PC
Info.
• Windows 7, click Start , right-click My Computer, and then select Properties.
System specifications
Feature Specification
Chipset Intel 6th Generation processors
DRAM bus width 64-bit
Flash EPROM SPI 128 Mbits
PCIe bus 100 MHz
External Bus
Frequency
PCIe Gen3 (8 GT/s)
Processor specifications
Feature Specification
Types Intel Core i5 series or i7 series
L3 cache
i5 series • non Vpro — 6 MB
• vPro — 8 MB
i7 series • vPro — 8 MB
45
Memory specifications
Feature Specification
Memory
connector
Two SODIMM slots
Memory capacity 4 GB and 8 GB
Memory type DDR4 SDRAM
Speed 2133 MHz
Minimum memory 4 GB
Maximum memory 8 GB
Storage specifications
Feature Specification
HDD Up to 1 TB
SSD 2.5 inches Up to 480 GB
SSD M.2 SATA /
PCIe
Up to 512 GB
Audio specifications
Feature Specification
Types High-definition audio
Controller Realtek ALC3235
Stereo conversion Digital audio-out through HDMI — up to 7.1 compressed and uncompressed audio
Internal interface High-definition audio codec
External interface Stereo headset/mic combo
Speakers Two
Internal speaker
amplifier
2 W (RMS) per channel
Volume controls Hot keys
Video specifications
Feature Specification
Type Integrated on system board, hardware accelerated
46
Feature Specification
UMA controller Intel HD Graphics 530 (quad core)
Data bus Integrated video
External display
support • 19-pin HDMI connector
• 15-pin VGA connector
Camera specifications
Feature Specification
HD Panel
Resolution
1366 1377 x 768 pixels
FHD Panel
Resolution
1920 x 1080 pixels
HD Panel Video
Resolution
(maximum)
1366 x 768 pixels
FHD Panel Video
Resolution
(maximum)
1920 x 1080 pixels
Diagonal viewing
angle
74°
Communication specifications
Features Specification
Network adapter 10/100/1000 Mb/s Ethernet (RJ-45)
Wireless Internal wireless local area network (WLAN), wireless wide area network (WWAN),
wireless gigabit (WiGig).
NOTE: WWAN and WiGig is optional. Bluetooth 4.1
Port and connector specifications
Feature Specification
Audio Stereo headset/mic combo
Video • One 19-pin HDMI connector
• 15 pin VGA connector
47
Feature Specification
Network adapter One RJ-45 connector
USB Three USB3.0, One USB 3.0 with PowerShare
Memory card
reader
Up to SD4.0
Micro SIM (uSIM)
card
One external (optional)
Docking port One
Contactless smart card specifications
Feature Specification
Supported Smart
Cards/
Technologies
BTO with USH
Display specifications
Feature Specification
Type • Non-touch FHD anti-glare
• HD anti-glare
Height 205.6 mm (8.09 inches)
Width 320.9 mm (12.63 inches)
Diagonal 355.6 mm (14 inches)
Active area (X/Y)
Non-touch FHD
anti-glare:
Maximum
resolution
1920 x 1080
Maximum
brightness
300 nits
Refresh rate 60 Hz
Maximum viewing
angles (horizontal)
80/80
Maximum viewing
angles (vertical)
80/80
48
Feature Specification
Pixel pitch 0.161 mm (0.006 inches)
Touch FHD anti-
glare:
Maximum
resolution
1920 x 1080
Maximum
brightness
270 nits
Refresh rate 60 Hz
Maximum viewing
angles (horizontal)
80/80
Maximum viewing
angles (vertical)
80/80
Pixel pitch 0.161 mm (0.006 inches)
HD anti-glare:
Maximum
resolution
1366 x 768
Maximum
brightness
200 nits
Refresh rate 60 Hz
Maximum viewing
angles (horizontal)
40/40
Maximum viewing
angles (vertical)
+10/-30
Pixel pitch 0.2265 mm (0.009 inches)
Keyboard specifications
Feature Specification
Number of keys • United States: 82 keys
• United Kingdom: 83 keys
• Japan: 86 keys
Touchpad specifications
Feature Specification
Active Area:
49
Feature Specification
X-axis 99.50 mm
Y-axis 53.00 mm
Battery specifications
Feature Specification
Type 62 Whr (4–Cell)
Depth 233.00 mm (9.17 inches)
Height 7.05 mm (0.27 inch)
Width 94.80 mm (3.73 inches)
Weight 340 g (0.75 lb)
Voltage 7.4 V DC
Life span 300 discharge per charge cycles
Temperature range
Operating • Charge: 0°C to 50°C
• Discharge: 0°C to 70°C
• Operating: 0°C to 35°C (32°F to 95°F)
Non-operating - 40°C to 65°C (- 40°F to 149°F)
Coin cell battery 3 V CR2032 lithium coin cell
AC Adapter specifications
Feature Specification
Type 65 W, 90 W (quad core)
Input voltage 100 V AC to 240 V AC
Input current
(maximum)
1.5 A
Input frequency 50 Hz to 60 Hz
Output current 3.34 A
50
Feature Specification
Rated output
voltage
19.5 +/– 1.0 V DC
Temperature range
(Operating)
0°C to 40°C (32°F to 104°F)
Temperature range
(Non-Operating)
–40°C to 70°C (–40°F to 158°F)
Physical specifications
Feature Specification
Front height (non-
touch) 23.3 mm (0.9 inch)
Front height
(touch) 24.53 mm (0.97 inch)
Back height (non-
touch) 23.95 mm (0.94 inch)
Back height
(touch) 25.35 mm (0.99 inch)
Width 334.9 mm (13.2 inches)
Depth 231.1 mm (9.1 inches)
Starting weight 3.88 lb (1.76 Kg)
Environmental specifications
Temperature Specifications
Operating 0°C to 35°C (32°F to 95°F)
Storage –40°C to 65°C (–40°F to 149°F)
Relative
humidity
(maximum)
Specifications
Operating 10 % to 90 % (non condensing)
Storage 5 % to 95 % (non condensing)
Altitude
(maximum) Specifications
Operating 0 m to 3048 m (0 ft to 10,000 ft)
Non-operating 0 m to 10,668 m (0 ft to 35,000 ft)
51
Airborne
contaminant level
G1 as defined by ISA-71.04–1985
52
5
Diagnostics
If you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for
technical assistance. The purpose of running diagnostics is to test your computer's hardware without
requiring additional equipment or risking data loss. If you are unable to fix the problem yourself, service
and support personnel can use the diagnostics results to help you solve the problem.
Enhanced Pre-Boot System Assessment (ePSA)
diagnostics
The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware.
The ePSA is embedded with the BIOS and is launched by the BIOS internally. The embedded system
diagnostics provides a set of options for particular devices or device groups allowing you to:
• Run tests automatically or in an interactive mode
• Repeat tests
• Display or save test results
• Run thorough tests to introduce additional test options to provide extra information about the failed
device(s)
• View status messages that inform you if tests are completed successfully
• View error messages that inform you of problems encountered during testing
CAUTION: Use the system diagnostics to test only your computer. Using this program with other
computers may cause invalid results or error messages.
NOTE: Some tests for specific devices require user interaction. Always ensure that you are present
at the computer terminal when the diagnostic tests are performed.
You can launch the ePSA diagnostics in two ways:
1. Power-on the computer.
2. As the computer boots, press the F12 key as the Dell logo appears.
3. On the boot menu screen, select the Diagnostics option.
The Enhanced Pre-boot System Assessment window displays, listing all devices detected in the
computer. The diagnostics starts running the tests on all the detected devices.
4. If you wish to run a diagnostic test on a specific device, press Esc and click Yes to stop the
diagnostic test.
5. Select the device from the left pane and click Run Tests
6. If there are any issues, error codes are displayed.
Note the error code and contact Dell.
OR
53
1. Shutdown the computer.
2. Press and hold the fn key, while pressing the power button, and then release both.
The Enhanced Pre-boot System Assessment window displays, listing all devices detected in the
computer. The diagnostics starts running the tests on all the detected devices.
3. On the boot menu screen, select the Diagnostics option.
The Enhanced Pre-boot System Assessment window displays, listing all devices detected in the
computer. The diagnostics starts running the tests on all the detected devices.
4. If you wish to run a diagnostic test on a specific device, press Esc and click Yes to stop the
diagnostic test.
5. Select the device from the left pane and click Run Tests
6. If there are any issues, error codes are displayed.
Note the error code and contact Dell.
Device status lights
Table 2. Device status lights
Icon Name Description
Power
status
light
Turns on when you turn on the computer and blinks when the computer is in a
power management mode.
Hard
drive
status
light
Turns on when the computer reads or writes data.
Battery
charge
indicator
Turns on steadily or blinks to indicate battery charge status.
NOTE: Refer to the following table for Battery charge LED indicator codes.
WiFi
indicator
Turns on when wireless networking is enabled.
The device status LEDs are usually located either on the top or left side of the keyboard. They display the
storage, battery and wireless devices connectivity and activity. Apart from that they can be useful as a
diagnostic tool when there's a possible failure to the system.
NOTE: The position of the power status light may vary depending on the system.
The following table lists how to read the LED codes when possible errors occur.
Table 3. Battery charge LED indicator
Amber blinking
pattern Problem description Suggested resolution
2,1 CPU CPU failure
2,2 System board: BIOS ROM System board, covers BIOS corruption or
ROM error
2,3 Memory No memory/RAM detected
54
Amber blinking
pattern Problem description Suggested resolution
2,4 Memory Memory/RAM failure
2,5 Memory Invalid memory installed
2,6 System board: Chipset System board / Chipset error
2,7 LCD Replace the system board
3,1 RTC Power Failure CMOS battery failure
3,2 PCI/Video PCI or video card/chip failure
The blinking patterns will consist of 2 set of numbers being represented by (First Group: Amber blinks,
Second Group: White blinks)
NOTE:
1. First Group: The LED blinks 1 to 9 times followed by a brief pause with LED off at the interval of
1.5 seconds.(This is in Amber color)
2. Second Group: The LED blinks 1 to 9 times, that would be then followed by a longer pause
before the next cycle starts again at the interval of 1.5 seconds.(This is in White color)
For Example: No Memory detected (2,3), Battery LED blinks two times of amber color followed by a
pause, and then blinks three times of white color. The Battery LED will pause for 3 seconds before the
next cycle repeat itself again.
Battery status lights
If the computer is connected to an electrical outlet, the battery light operates as follows:
Alternately blinking
amber light and
white light
An unauthenticated or unsupported non-Dell AC adapter is attached to your
laptop.
Alternately blinking
amber light with
steady white light
Temporary battery failure with AC adapter present.
Constantly blinking
amber light
Fatal battery failure with AC adapter present.
Light off Battery in full charge mode with AC adapter present.
White light on Battery in charge mode with AC adapter present.
55
6
Contacting Dell
NOTE: If you do not have an active Internet connection, you can find contact information on your
purchase invoice, packing slip, bill, or Dell product catalog.
Dell provides several online and telephone-based support and service options. Availability varies by
country and product, and some services may not be available in your area. To contact Dell for sales,
technical support, or customer service issues:
1. Go to Dell.com/support.
2. Select your support category.
3. Verify your country or region in the Choose a Country/Region drop-down list at the bottom of the
page.
4. Select the appropriate service or support link based on your need.
56