DELL E7450 + 452-11420 User Manual

Displayed below is the user manual for E7450 + 452-11420 by DELL which is a product in the Notebooks category. This manual has pages.

Related Manuals

DELL E7450 Manual

Dell Latitude E7450

Owner's Manual

Regulatory Model: P40G

Regulatory Type: P40G002

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of your computer.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you

how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

intellectual property laws. Dell™ and the Dell logo are trademarks of Dell Inc. in the United States and/or other

jurisdictions. All other marks and names mentioned herein may be trademarks of their respective companies.

2014 -12

Rev. A00

Contents

1 Working on Your Computer................................................................................5

Before Working Inside Your Computer................................................................................................ 5

Turning Off Your Computer..................................................................................................................6

After Working Inside Your Computer................................................................................................... 7

2 Docking Your Computer..................................................................................... 8

3 Removing and Installing Components............................................................. 9

Recommended Tools............................................................................................................................9

Removing the Battery............................................................................................................................9

Installing the Battery............................................................................................................................10

Removing the Base Cover...................................................................................................................10

Installing the Base Cover..................................................................................................................... 11

Removing the Hard Drive.................................................................................................................... 11

Installing the Hard Drive......................................................................................................................12

Removing the Coin-Cell Battery.........................................................................................................12

Installing the Coin-Cell Battery...........................................................................................................13

Removing the WWAN Card.................................................................................................................13

Installing the WWAN Card...................................................................................................................14

Removing the WLAN Card.................................................................................................................. 14

Installing the WLAN Card.................................................................................................................... 14

Removing the System Fan...................................................................................................................15

Installing the System Fan.....................................................................................................................15

Removing the Display Bezel................................................................................................................15

Installing the Display Bezel..................................................................................................................16

Removing the Display Panel............................................................................................................... 16

Installing the Display Panel................................................................................................................. 18

Removing the Camera........................................................................................................................ 18

Installing the Camera.......................................................................................................................... 19

Removing the Keyboard Trim............................................................................................................. 19

Installing the Keyboard Trim...............................................................................................................20

Removing the Keyboard..................................................................................................................... 20

Installing the Keyboard....................................................................................................................... 22

Removing the Palmrest.......................................................................................................................22

Installing the Palmrest.........................................................................................................................23

Removing the Speakers...................................................................................................................... 24

Installing the Speaker.......................................................................................................................... 25

Removing the I/O Board.....................................................................................................................25

Installing the Speaker.......................................................................................................................... 25

Removing the Display-Hinge Cover...................................................................................................26

Installing the Display-Hinge Cover.....................................................................................................27

Removing the Display Assembly.........................................................................................................27

Installing the Display Assembly...........................................................................................................29

Removing the System Board.............................................................................................................. 30

Installing the System Board.................................................................................................................31

Removing the Heatsink.......................................................................................................................32

Installing the Heatsink.........................................................................................................................32

Removing the Power Connector .......................................................................................................33

Installing the Power Connector......................................................................................................... 34

4 System Setup....................................................................................................... 35

Boot Sequence....................................................................................................................................35

Navigation Keys................................................................................................................................... 35

System Setup Options.........................................................................................................................36

Updating the BIOS ..............................................................................................................................45

System and Setup Password...............................................................................................................46

Assigning a System Password and Setup Password.................................................................... 46

Deleting or Changing an Existing System and/or Setup Password.............................................47

5 Diagnostics.......................................................................................................... 48

Enhanced Pre-Boot System Assessment (ePSA) Diagnostics........................................................... 48

Device Status Lights............................................................................................................................49

Battery Status Lights............................................................................................................................49

6 Specifications...................................................................................................... 51

7 Contacting Dell................................................................................................... 57

Working on Your Computer

Before Working Inside Your Computer

Use the following safety guidelines to help protect your computer from potential damage and to help to

ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes

that the following conditions exist:

• You have read the safety information that shipped with your computer.

• A component can be replaced or--if purchased separately--installed by performing the removal

procedure in reverse order.

WARNING: Disconnect all power sources before opening the computer cover or panels. After you

finish working inside the computer, replace all covers, panels, and screws before connecting to

the power source.

WARNING: Before working inside your computer, read the safety information that shipped with

your computer. For additional safety best practices information, see the Regulatory Compliance

Homepage at www.dell.com/regulatory_compliance

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or

by periodically touching an unpainted metal surface, such as a connector on the back of the

computer.

CAUTION: Handle components and cards with care. Do not touch the components or contacts

on a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a

processor by its edges, not by its pins.

CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable

itself. Some cables have connectors with locking tabs; if you are disconnecting this type of cable,

press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep

them evenly aligned to avoid bending any connector pins. Also, before you connect a cable,

ensure that both connectors are correctly oriented and aligned.

NOTE: The color of your computer and certain components may appear differently than shown in

this document.

To avoid damaging your computer, perform the following steps before you begin working inside the

computer.

1. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.

2. Turn off your computer (see Turning off Your Computer).

3. If the computer is connected to a docking device (docked), undock it.

CAUTION: To disconnect a network cable, first unplug the cable from your computer and

then unplug the cable from the network device.

4. Disconnect all network cables from the computer.

5. Disconnect your computer and all attached devices from their electrical outlets.

6. Close the display and turn the computer upside-down on a flat work surface.

NOTE: To avoid damaging the system board, you must remove the main battery before you

service the computer.

7. Remove the main battery.

8. Turn the computer top-side up.

9. Open the display.

10. Press the power button to ground the system board.

CAUTION: To guard against electrical shock, always unplug your computer from the

electrical outlet before opening the display.

CAUTION: Before touching anything inside your computer, ground yourself by touching an

unpainted metal surface, such as the metal at the back of the computer. While you work,

periodically touch an unpainted metal surface to dissipate static electricity, which could

harm internal components.

11. Remove any installed ExpressCards or Smart Cards from the appropriate slots.

Turning Off Your Computer

CAUTION: To avoid losing data, save and close all open files and exit all open programs before

you turn off your computer.

1. Shut down the operating system:

• In Windows 8 (touch-enabled device):

1. Swipe in from the right edge of the screen, opening the Charms menu and select Settings.

2. Select the and then select Shut down.

• Using a mouse:

1. Point to upper-right corner of the screen and click Settings.

2. Click the and select Shut down.

• In Windows 7:

1. Click Start .

2. Click Shut Down.

1. Click Start .

2. Click the arrow in the lower-right corner of the Start menu as shown below, and then click

Shut Down

2. Ensure that the computer and all attached devices are turned off. If your computer and attached

devices did not automatically turn off when you shut down your operating system, press and hold

the power button for about 6 seconds to turn them off.

After Working Inside Your Computer

After you complete any replacement procedure, ensure you connect any external devices, cards, and

cables before turning on your computer.

CAUTION: To avoid damage to the computer, use only the battery designed for this particular

Dell computer. Do not use batteries designed for other Dell computers.

1. Connect any external devices, such as a port replicator or media base, and replace any cards, such as

an ExpressCard.

2. Connect any telephone or network cables to your computer.

CAUTION: To connect a network cable, first plug the cable into the network device and then

plug it into the computer.

3. Replace the battery.

4. Connect your computer and all attached devices to their electrical outlets.

5. Turn on your computer.

Docking Your Computer

Follow the steps to dock your computer:

a. Place the docking spacer until the docking spacer clicks on its place in the docking station.

b. Place the computer on the docking spacer to dock your computer.

NOTE: This docking spacer can be used to dock only the Latitude E7250 / Latitude E7450

computers. You cannot dock any other Dell computers using this docking station.

NOTE: The docking spacer and the dock are optional items and do not ship standard with a

system.

Removing and Installing Components

This section provides detailed information on how to remove or install the components from your

computer.

Recommended Tools

The procedures in this document may require the following tools:

• Small flat-blade screwdriver

• Phillips screwdriver

• Small plastic scribe

Removing the Battery

1. Follow the procedures in Before Working Inside Your Computer.

2. Slide the release latch to unlock the battery.

3. Lift the battery from the computer.

Installing the Battery

1. Slide the battery into its slot until it clicks into place.

2. Follow the procedures in After Working Inside Your computer.

Removing the Base Cover

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove battery.

3. Perform the following steps as shown in the illustration:

a. Remove the screws that secure the base cover to the computer [1].

b. Slide the base cover [2].

4. Lift the base cover to remove it from the computer.

Installing the Base Cover

1. Place the base cover to align with the screw holes correctly on the computer.

2. Tighten the screws to secure the base cover to the computer.

3. Install battery.

4. Follow the procedures in After Working Inside Your computer.

Removing the Hard Drive

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. base cover

3. Perform the following steps as shown in the illustration:

a. Disconnect the hard drive cable from the computer [1].

b. Remove the screws that secure the hard drive to the computer [2].

c. Lift the hard drive partially at a 45–degree angle [3].

4. Lift the hard drive from the computer.

Installing the Hard Drive

1. Place the hard drive inside the computer.

2. Tighten the screw that secures the hard drive to the computer.

3. Connect the hard drive cable.

4. Install

a. base cover

b. battery

5. Follow the procedures in After Working Inside Your computer.

Removing the Coin-Cell Battery

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. base cover

3. Perform the following steps as shown in the illustration:

a. Disconnect the coin-cell cable from the computer [1].

b. Lift the coin-cell battery from the computer [2].

Installing the Coin-Cell Battery

1. Place the Coin-cell battery on the computer.

2. Connect the coin-cell battery cable to the computer.

3. Install:

a. base cover

b. battery

4. Follow the procedures in After Working Inside Your computer.

Removing the WWAN Card

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. base cover

3. Perform the following steps as shown in the illustration:

a. Disconnect the WWAN cable from the computer [1].

b. Loosen the screws that secure the WWAN card to the computer [2].

c. Remove the WWAN card from the computer [3].

Installing the WWAN Card

1. Place the WWAN card in its slot in the computer.

2. Tighten the screws to secure the WWAN Card to the computer.

3. Connect the WWAN cable to the computer.

4. Install :

a. base cover

b. battery

5. Follow the procedures in After Working Inside Your computer.

Removing the WLAN Card

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. base cover

3. Perform the following steps as shown in the illustration:

a. Remove the screw that secures the WLAN card to the computer [1].

b. Lift the tab [2].

c. Disconnect the WLAN cable from the computer [3].

d. Remove the WLAN card from the computer [4].

Installing the WLAN Card

1. Place the WLAN card in its slot in the computer.

2. Connect the WLAN cable to the computer.

3. Place and tab and tighten the screws to secure the WLAN Card to the computer.

4. Install :

a. base cover

b. battery

5. Follow the procedures in After Working Inside Your computer.

Removing the System Fan

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. base cover

3. Perform the following steps as shown in the illustration:

a. Disconnect the system fan cable [1].

b. Remove the screws that secure the system fan to the computer [2].

c. Remove the system fan from the computer [3].

Installing the System Fan

1. Place the system fan in its slot in the computer.

2. Tighten the screws that secure the system fan to the computer.

3. Connect the system fan cable to the computer.

4. Install :

a. base cover

b. battery

5. Follow the procedures in After Working Inside Your computer.

Removing the Display Bezel

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove battery.

3. Pry the edges of the display bezel.

4. Lift the display bezel from the display assembly.

Installing the Display Bezel

1. Align the display bezel in place and snap it in place.

2. Align the hinge covers on display assembly and snap it in place.

3. Install the battery.

4. Follow the procedures in After Working Inside Your computer.

Removing the Display Panel

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove .

a. battery

b. display bezel

3. Perform the following steps as shown in the illustration:

a. Remove the screws that secure the display panel to the display assembly [1].

b. Lift the display panel [2].

4. Perform the following steps as shown in the illustration:

a. Peel the connector tape [1].

b. Lift the tape [2].

5. Perform the following steps as shown in the illustration:

a. Peel the display assembly cable connector tape [1].

b. Disconnect the display assembly cable from the display panel [2].

c. Remove the display panel from the display assembly [3].

Installing the Display Panel

1. Connect the display assembly cable to its connector on the display panel.

2. Place the display panel to its original position on the display assembly.

3. Tighten the screws to secure the display panel to the display assembly.

4. Install:

a. display bezel

b. battery

5. Follow the procedures in After Working Inside Your computer.

Removing the Camera

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove .

a. battery

b. display bezel

c. display panel

3. Perform the following steps as shown in the illustration:

a. Disconnect the camera cable from the module [1].

b. Lift and remove the camera from the display assembly [2].

Installing the Camera

1. Install the camera into its slot on the display panel.

2. Connect the camera cable to the camera.

3. Tighten the screws to secure the display panel to the display assembly.

4. Install the

a. display panel

b. display bezel

c. battery

5. Follow the procedures in After Working Inside Your computer.

Removing the Keyboard Trim

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove battery.

3. Using a plastic scribe, pry the edges of keyboard trim to release it from the computer.

4. Lift up to remove the keyboard trim from the computer.

Installing the Keyboard Trim

1. Align the keyboard trim to its slot.

2. Press along the sides of the keyboard trim until it clicks in place.

3. Install battery.

4. Follow the procedures in After Working Inside Your computer

Removing the Keyboard

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove .

a. battery

b. base cover

c. keyboard trim

3. Perform the following steps as shown in the illustration:

a. Lift the battery bay [1].

b. Lift the tab [2].

c. Disconnect the keyboard-backlight cable [3].

4. Remove the screws that secure the keyboard to the computer.

5. Perform the following steps as shown in the illustration:

a. Slide the keyboard [1]

b. Lift the keyboard from the computer [2].

Installing the Keyboard

1. Align the keyboard to its slot.

2. Tighten the screws to secure the keyboard on the palmrest.

3. Connect the keyboard-backlight cable to the computer.

4. Install

a. keyboard trim

b. base cover

c. battery.

5. Follow the procedures in After Working Inside Your computer

Removing the Palmrest

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove .

a. battery

b. base cover

c. keyboard trim

d. keyboard

3. Remove the screws that secure the palmrest assembly to the computer.

4. Perform the following steps as shown in the illustration:

a. Lift the latch [1].

b. Disconnect touchpad and power LED cables from the computer [2].

c. Remove the screws that secures palmrest assembly to the computer [3].

5. Perform the following steps as shown in the illustration:

a. Pry the edges of the palmrest assembly [1]

b. Lift up the palmrest away from the computer [2].

Installing the Palmrest

1. Align the palm rest assembly to its original position in the computer and snap it into place.

2. Connect the power LED cable and touchpad cable.

3. Tighten the screws to secure the palmrest assembly to the front of the computer.

4. Tighten the screws to secure the palmrest assembly to the base of the computer.

5. Install

a. keyboard

b. keyboard trim

c. base cover

d. battery.

6. Follow the procedures in After Working Inside Your computer

Removing the Speakers

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. base cover

c. hard drive

d. keyboard trim

e. keyboard

f. palmrest

3. Perform the following steps as shown in the illustration:

a. Disconnect the speaker cable [1].

b. Unroute the cable from the system board [2].

4. Perform the following steps as shown in the illustration:

a. Remove the screws that secure speaker to the computer chassis [1].

b. Remove the speakers from the computer [2].

Installing the Speaker

1. Align the speakers to their original position and tighten the screws to secure the speakers to the

computer.

2. Route the speaker cable on the computer and connect it to the system board.

3. Install:

a. palmrest

b. keyboard

c. keyboard trim

d. hard drive

e. base cover

f. battery.

4. Follow the procedures in After Working Inside Your computer .

Removing the I/O Board

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. base cover

c. hard drive

d. keyboard trim

e. keyboard

f. palmrest

3. Perform the following steps as shown in the illustration:

a. Lift the latch [1].

b. Disconnect the I/O cable from the system board [2].

c. Remove the screw that secures the I/O board to the computer. [3].

d. Remove the I/O board from the computer [4].

Installing the Speaker

1. Place the I/O board in its slot and snap it in place.

2. Tighten the screws to secure the I/O board.

3. Connect the I/O cable to the system board.

4. Install

a. palmrest

b. keyboard

c. keyboard trim

d. hard drive

e. base cover

f. battery.

5. Follow the procedures in After Working Inside Your computer

Removing the Display-Hinge Cover

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. base cover

c. keyboard trim

d. keyboard

e. palmrest

3. Remove the screws that secure the display-hinge cover to the computer.

4. Perform the following steps as shown in the illustration:

a. Remove the screws that secure hinge to the system board [1].

b. Lift the Hinge from the computer [2].

Installing the Display-Hinge Cover

1. Place the display-hinge cover and tighten the screws to secure the display-hinge cover to the system

board.

2. Tighten the screw that secures hinge cap to the computer.

3. Instal:

a. palmrest

b. keyboard

c. keyboard trim

d. base cover

e. battery

4. Follow the procedures in After Working Inside Your computer.

Removing the Display Assembly

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. base cover

c. keyboard trim

d. keyboard

e. hard drive

f. palmrest

3. Unroute the WWAN and WLAN cable from the slot.

4. Perform the following steps as shown in the illustration:

a. Remove the screw that secures the display assembly cable to the computer [1].

b. Lift the tab that securesdisplay assembly cable to the computer [2].

c. Lift the tab securing the display assembly to the computer [3].

d. Disconnect the cable from the computer [4].

5. Pull the antenna cables from the holes on the base chassis that secure the display assembly to the

computer.

6. Perform the following steps as shown in the illustration:

a. Remove the screws that secure the display assembly to the computer [1].

b. Lift the display assembly from the computer [2].

Installing the Display Assembly

1. Insert the wireless antenna cables through the holes on the base chassis and connect them.

2. Place the display assembly onto the computer.

3. Tighten the screws on both sides to secure the display assembly.

4. Route and connect the display assembly cables through the routing channel.

5. Route the WWAN and WLAN cables to the computer.

6. Install:

a. palmrest

b. hard drive

c. keyboard

d. keyboard trim

e. base cover

f. battery

7. Follow the procedures in After Working Inside Your computer.

Removing the System Board

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. base cover

c. keyboard trim

d. keyboard

e. hard drive

f. palmrest

g. WWAN card

h. WLAN card

i. hinge cover

j. display assembly

3. Disconnect the display assembly cable from the computer.

4. Perform the following steps as shown in the illustration:

a. Disconnect the speaker cable [1].

b. Lift the tab that secures I/O board cable [2].

c. Disconnect the I/O board cable from system board [3].

5. Perform the following steps as shown in the illustration:

a. Remove the screws that secure the system board to computer chassis [1].

b. Lift the system board from the computer [2].

Installing the System Board

1. Align the system board in its place on the computer.

2. Tighten the screws to secure the system board.

3. Connect the spekar and I/O board cables to the system board.

4. Connect display assembly cable.

5. Install:

a. display assembly

b. hinge cover

c. WLAN card

d. WWAN card

e. palmrest

f. hard drive

g. keyboard trim

h. keyboard

i. base cover

j. battery

6. Follow the procedures in After Working Inside Your computer.

Removing the Heatsink

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. base cover

c. keyboard trim

d. keyboard

e. palmrest

f. hard drive

g. WWAN card

h. WLAN card

i. display assembly

j. system fan

k. speakers

3. Perform the following steps as shown in the illustration:

a. Remove the screws that secure the heatsink to the system board [1].

b. Lift the heatsink from the system board [2].

Installing the Heatsink

1. Place the heatsink into its original position on the system board.

2. Tighten the screws to secure the heatsink to the system board.

3. Install:

a. speaker

b. system fan

c. display assembly

d. WLAN card

e. WWAN card

f. hard drive

g. palmrest

h. keyboard

i. keyboard trim

j. base cover

k. battery

4. Follow the procedures in After Working Inside Your computer.

Removing the Power Connector

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. base cover

c. keyboard trim

d. keyboard

e. palmrest

f. hard drive

g. WWAN card

h. WLAN card

i. hinge cover

j. display assembly

k. camera

l. coincell battery

m. I/O board

n. speakers

o. system fan

p. system board

3. Perform the following steps as shown in the illustration:

a. Remove the screws that secures power connector to the computer chassis [1].

b. Disconnect the power-connector cable from the computer chassis [2].

c. Remove the power connector [3].

Installing the Power Connector

1. Insert the power connector in its slot.

2. Connect the power connector to the system board.

3. Tighten the screw that secures the power connector to the system board.

4. Install:

a. system board

b. system fan

c. speaker

d. I/O board

e. coincell battery

f. camera

g. display assembly

h. hinge cover

i. WLAN card

j. WWAN card

k. hard drive

l. palmrest

m. keyboard

n. keyboard trim

o. base cover

p. battery

5. Follow the procedures in After Working Inside Your computer.

System Setup

Boot Sequence

Boot Sequence allows you to bypass the System Setup‐defined boot device order and boot directly to a

specific device (for example: optical drive or hard drive). During the Power-on Self Test (POST), when the

Dell logo appears, you can:

• Access System Setup by pressing <F2> key

• Bring up the one-time boot menu by pressing <F12> key

The one-time boot menu displays the devices that you can boot from including the diagnostic option.

The boot-menu options are:

• Removable Drive (if available)

• STXXXX Drive

NOTE: XXX denotes the SATA drive number.

• Optical Drive

• Diagnostics

NOTE: Choosing Diagnostics, will display the ePSA diagnostics screen.

The boot sequence screen also displays the option to access the System Setup screen.

Navigation Keys

The following table displays the system setup navigation keys.

NOTE: For most of the system setup options, changes that you make are recorded but do not take

effect until you re-start the system.

Table 1. Navigation Keys

Keys Navigation

Up arrow Moves to the previous field.

Down arrow Moves to the next field.

<Enter> Allows you to select a value in the selected field (if applicable) or follow the link in

the field.

Spacebar Expands or collapses a drop‐down list, if applicable.

<Tab> Moves to the next focus area.

Keys Navigation

NOTE: For the standard graphics browser only.

<Esc> Moves to the previous page till you view the main screen. Pressing <Esc> in the main

screen displays a message that prompts you to save any unsaved changes and

restarts the system.

<F1> Displays the System Setup help file.

System Setup Options

NOTE: Depending on your computer and its installed devices, the items listed in this section may or

may not appear.

Table 2. General

Option Description

System Information This section lists the primary hardware

features of your computer.

• System Information: Displays BIOS

Version, Service Tag, Asset Tag,

Ownership Tag, Ownership Date,

Manufacture Date, and the Express

Service Code.

• Memory Information: Displays

Memory Installed, Memory Available,

Memory Speed, Memory Channels

Mode, Memory Technology, DIMM

ASize, DIMM B Size,

• Processor Information: Displays

Processor Type, Core Count,

Processor ID, Current Clock Speed,

Minimum Clock Speed, Maximum

Clock Speed, Processor L2 Cache,

Processor L3 Cache, HT Capable,

and 64-Bit Technology.

• Device Information: Displays Primary

Hard Drive, System eSATA Device,

Dock eSATA Device, LOM MAC

Address, Video Controller, Video

BIOS Version, Video Memory, Panel

Type, Native Resolution, Audio

Controller, Modem Controller, Wi-Fi

Device, WiGig Device, Cellular

Device, Bluetooth Device.

Battery Information Displays the battery status and the type

of AC adapter connected to the

computer

Boot Sequence Allows you to change the order in which

the computer attempts to find an

operating system.

• Diskette Drive

• Internal HDD

• USB Storage Device

• CD/DVD/CD-RW Drive

Option Description

• Onboard NIC

Advance Boot Option This option is required for Legacy boot

mode. This option is not allowed if

Secure Boot is enabled.

•Enable Legacy Option ROMs — This

option is disabled by default.

Date/Time Allows you to set the date and time.

Table 3. System Configuration

Option Description

Integrated NIC Allows you to configure the integrated

network controller. The options are:

• Disabled

• Enabled

• Enabled w/PXE: This option is

enabled by default.

• Enable UEFI Network Stack: This

allows you to enable UEFI

Networking Protocols in pre-OS and

early OS networking environment.

Parallel Port Allows you to define and set how the

parallel port on the docking station

operates. You can set the parallel port

to:

• Disabled

•AT

• PS2

• ECP

Serial Port Identifies and defines the serial port

settings. You can set the serial port to:

• Disabled

•COM1 (Default Setting)

• COM2

• COM3

• COM4

NOTE: The operating system may

allocate resources even if the

setting is disabled.

SATA Operation Allows you to configure the internal

SATA hard-drive controller. The options

are:

• Disabled

• AHCI

•RAID On (Default Setting)

Option Description

NOTE: SATA is configured to

support RAID mode.

Drives Allows you to configure the SATA drives

on board. The options are:

• SATA-0

• SATA-1

• SATA-2

• SATA-3

Default Setting: All drives are enabled.

SMART Reporting This field controls if the hard drive errors

for the integrated drives are reported

during system startup. This technology

is part of the SMART (Self Monitoring

Analysis and Reporting Technology)

specification.

•Enable SMART Reporting - This

option is disabled by default.

USB Configuration Allows you to define the USB

configuration. The options are:

• Enable Boot Support

• Enable External USB Port

• Enable USB3.0 Controller

Default Setting: all the options are

enabled.

USB PowerShare Allows you to configure the behavior of

the USB PowerShare feature. The option

is disabled by default.

• Enable USB PowerShare

Audio Allows you to enables or disables the

integrated audio controller.

•Enable AudioThis option is enabled

by default.

Unobtrusive Mode Allows you to set the mode that will turn

off all light and sound emissions from

the system. The option is disabled by

default.

• Enable Unobtrusive Mode

Miscellaneous Devices Allows you enable or disable the various

on board devices. The options are:

• Enable Microphone

• Enable Hard Drive Free Fall

Protection

Option Description

• Enable Camera

• Enable Media Card

• Disable Media Card

Default Setting: All devices are enabled

Table 4. Video

Option Description

LCD Brightness Allows you to set the display brightness depending up on the power

source (On Battery and On AC).

Table 5. Security

Option Description

Admin Password This field lets you set, change, or delete the administrator (admin)

password (sometimes called the setup password). The admin password

enables several security features.

• Enter the old password

• Enter the new password

• Confirm the new password

Default Setting: Not set

System Password Allows you to set, change or delete the system password.

• Enter the old password

• Enter the new password

• Confirm the new password

Default Setting: Not set

Internal HDD-1 Password Allows you to set, change or delete the administrator password.

The drive does not have a password set by default.

• Enter the old password

• Enter the new password

• Confirm the new password

Default Setting: Not set

Strong Password Allows you to enforce the option to always set strong passwords.

Default Setting: Enable Strong Password is not selected.

Password Configuration You can define the length of your password. Min = 4 , Max = 32

Password Bypass Allows you to enable or disable the permission to bypass the System

and the Internal HDD password, when they are set. The options are:

•Disabled (Default Setting)

• Reboot bypass

Option Description

Password Change Allows you to enable the disable permission to the System and Hard

Drive passwords when the admin password is set.

Default Setting: Allow Non-Admin Password Changes is not selected

Non-Admin Setup Changes Allows you to determine whether changes to setup option are

permitted when an administrator password is set. The option is

disabled.

• Allows Wireless Switch Changes

TPM Security Allows you to enable the Trusted Platform Module (TPM) during POST.

Default Setting: The option is disabled.

Computrace Allows you to activate or disable the optional Computrace software The

options are:

•Deactivate (Default Setting)

• Disable

• Activate

NOTE: The Activate and Disable options will permanently activate

or disable the feature and no further changes will be allowed

CPU XD Support Allows you to enable the Execute Disable mode of the processor.

Default Setting: Enable CPU XD Support

OROM Keyboard Access Allows you to set access to enter the Option ROM Configuration

screens using hotkeys during boot process. The options are:

•Enable (Default Setting)

• One Time Enable

• Disable

Admin Setup Lockout Allows you to prevent users from entering Setup when an Administrator

password is set.

Default Setting: Disabled

Table 6. Secure Boot

Secure Boot Enable Allows you to enable or disable Secure Boot feature

• Disabled

•Enabled(Default Setting)

NOTE: For enable system needs to be UEFI boot mode and enable

legacy option ROMs to be turned off.

Expert key Management Allows you to manipulate the security key databases only if the system

is in Custom Mode. The Enable Custom Mode option is disabled by

default. The options are:

• PK

• KEK

• db

• dbx

If you enable the Custom Mode, the relevant options for PK, KEK, db,

and dbx appear. The options are:

• Save to File- Saves the key to a user-selected file

• Replace from File- Replaces the current key with a key from a user-

selected file

• Append from File- Adds a key to the current database from a user-

selected file

• Delete- Deletes the selected key

• Reset All Keys- Resets to default setting

• Delete All Keys- Deletes all the keys

NOTE: If you disable the Custom Mode, all the changes made will

be erased and the keys will restore to default settings.

Table 7. Performance

Option Description

Multi Core Support This field specifies whether the process

will have one or all cores enabled. The

performance of some applications will

improve with the additional cores. This

option is enabled by default. Allows you

to enable or disable multi-core support

for the processor. The options are:

•All (Default Setting)

• 1

• 2

Intel SpeedStep Allows you to enable or disable the Intel

SpeedStep feature.

Default Setting: Enable Intel SpeedStep

C States Control Allows you to enable or disable the

additional processor sleep states.

Default Setting: The option C states is

enabled.

Intel TurboBoost Allows you to enable or disable the Intel

TurboBoost mode of the processor.

Default Setting: Enable Intel

TurboBoost

Hyper-Thread Control Allows you to enable or disable the

HyperThreading in the processor.

Default Setting: Enabled

Table 8. Power Management

Option Description

AC Behavior Allows the computer to power-on automatically, when AC adapter is

plugged. The option is disabled.

Option Description

• Wake on AC

Auto On Time Allows you to set the time at which the computer must turn on

automatically. The options are:

•Disabled (Default Setting)

• Every Day

• Weekdays

• Select Days

USB Wake Support Allows you to enable the USB devices to wake the computer from

standby mode. The option is disabled

• Enable USB Wake Support

Wireless Radio Control Allows you to control the WLAN and WWAN radio. The options are:

• Control WLAN radio

• Control WWAN radio

Default Setting: both the options are disabled.

Wake on LAN/WLAN This option allows the computer to power up from the off state when

triggered by a special LAN signal. Wake-up from the Standby state is

unaffected by this setting and must be enabled in the operating system.

This feature only works when the computer is connected to AC power

supply.

•Disabled - Does not allow the system to power on by special LAN

signals when it receives a wake-up signal from the LAN or wireless

LAN. (Default Setting)

• LAN Only - Allows the system to be powered on by special LAN

signals.

• WLAN Only

• LAN or WLAN

Block Sleep Allows you to block the computer from entering into the sleep state.

Option is disabled by default.

• Block Sleep (S3)

Peak Shift Peak Shift can be used to minimize AC consumption during peak powers

times of day. Set the start and end time to run in Peak Shift mode.

•Enable Peak Shift (Disabled)

Advanced Battery Charge

Configuration

Allows batteries in the system in Advanced Battery Charge Mode to

maximize battery health. This uses standard charging algorithm and

other techniques during non-work hours to maximize battery health

•Enable Advanced Battery Charge Mode(Disabled)

Primary Battery

Configuration

Allows you to define how to use the battery charge, when AC is plugged

in. The options are:

•Adaptive(Enabled)

• Standard Charge

• Express Charge

Option Description

• Primary AC Use

• Custom Charge — you can set the percentage to which the battery

must charge.

Intel Smart Connect

Technology

The option is disabled by default. If option enables will periodically sense

nearby wireless connection while the system is asleep. It will synchronize

emails or social media application that were open when system entered

the sleep state.

•Smart Connection(Disabled)

Table 9. POST Behavior

Option Description

Adapter Warnings Allows you to activate the adapter warning messages when certain

power adapters are used. The option is enabled by default.

• Enable Adapter Warnings

Keypad (Embedded) Allows you to choose one of two mode it enable the keypad that us

embedded in the internal keyboard.

• Fn Key Only

• By Numlock

NOTE: When setup is running, this option has no effect, Setup

works in the “Fn Key Only” mode.

Mouse/Touchpad Allows you to define how the computer handles the mouse and

touchpad input. The options are:

• Serial Mouse

• PS2 Mouse

•Touchpad/PS-2 Mouse (Default Setting)

Numlock Enable Specifies if the NumLock function can be enabled when the computer

boots. This option is enabled by default.

• Enable Numlock

Fn Key Emulation Allows you to match the <Scroll Lock> key feature of PS-2 keyboard with

the <Fn> key feature in an internal keyboard. The option is enabled by

default.

• Enable Fn Key Emulation

Fn Lock Option Allows you to hot keys combination toggle the primary behavior. The

option are:

• Fn Lock

• Lock Mode Disable/Standard

• Lock Mode Enable/Secondary

MEBx Hotkey Allows you to specifies whether the MEBx Hotkey function should be

enable when the system boots. The option is enabled by default.

Fastboot Allows you to speed up the boot process by bypassing some

compatibility steps.

Option Description

• Minimal

• Thorough

• Auto

Extended BIOS POST Time Allows to creates an additional pre-boot delay and allows the user to see

POST status message.

• 0 seconds

• 5 seconds

• 10 seconds

Table 10. Virtualization Support

Option Description

Virtualization Allows you to enable or disable the Intel Virtualization Technology.

Default Setting: Enable Intel Virtualization Technology

VT for Direct I/O Enables or disables the Virtual Machine Monitor (VMM) from utilizing the

additional hardware capabilities provided by Intel® Virtualization

technology for direct I/O.

Enable VT for Direct I/O — This option is enabled by default.

Trusted Execution This option specifies whether a Measured Virtual Machine Monitor

(MVMM) can utilize the additional hardware capabilities provided by Intel

Trusted Execution Technology. The TPM virtualization Technology, and

Virtualization technology for direct I/O must be enabled to use this

feature.

Trusted Execution — disabled by default.

Table 11. Wireless

Option Description

Wireless Switch Allows you to determine which wireless device can be controlled by the

wireless switch. The options are:

• WWAN

• WLAN/WiGi

• Bluetooth

• GPS (on WWAN module)

All options are enabled by default.

Wireless Device Enable Allows you to enable or disable the wireless devices. The options are:

• WWAN/GPS

• Bluetooth

• WLAN/WiGig

All options are enabled by default.

Table 12. Maintenance

Option Description

Service Tag Displays the service tag of your computer.

Asset Tag Allows you to create a system asset tag if an asset tag is not already set.

This option is not set by default.

Table 13. System Logs

Option Description

BIOS events Displays the system event log and allows you to clear the log.

• Clear Log

Thermal Events Displays the thermal event log and allows you to clear the log.

• Clear Log

Power Events Displays the power event log and allows you to clear the log.

• Clear Log

Updating the BIOS

It is recommended to update your BIOS (system setup), on replacing the system board or if an update is

available. For laptops, ensure that your computer battery is fully charged and connected to a power

outlet

1. Re-start the computer.

2. Go to dell.com/support.

3. Enter the Service Tag or Express Service Code and click Submit.

NOTE: To locate the Service Tag, click Where is my Service Tag?

NOTE: If you cannot find your Service Tag, click Detect My Product. Proceed with the

instructions on screen.

4. If you are unable to locate or find the Service Tag, click the Product Category of your computer.

5. Choose the Product Type from the list.

6. Select your computer model and the Product Support page of your computer appears.

7. Click Get drivers and click View All Drivers.

The Drivers and Downloads page opens.

8. On the Drivers and Downloads screen, under the Operating System drop-down list, select BIOS.

9. Identify the latest BIOS file and click Download File.

You can also analyze which drivers need an update. To do this for your product, click Analyze

System for Updates and follow the instructions on the screen.

10. Select your preferred download method in the Please select your download method below window,

click Download File.

The File Download window appears.

11. Click Save to save the file on your computer.

12. Click Run to install the updated BIOS settings on your computer.

Follow the instructions on the screen.

System and Setup Password

You can create a system password and a setup password to secure your computer.

Password Type Description

System password Password that you must enter to log on to your system.

Setup password Password that you must enter to access and make changes to the BIOS settings of

your computer.

CAUTION: The password features provide a basic level of security for the data on your computer.

CAUTION: Anyone can access the data stored on your computer if it is not locked and left

unattended.

NOTE: Your computer is shipped with the system and setup password feature disabled.

Assigning a System Password and Setup Password

You can assign a new System Password and/or Setup Password or change an existing System Password

and/or Setup Password only when Password Status is Unlocked. If the Password Status is Locked, you

cannot change the System Password.

NOTE: If the password jumper is disabled, the existing System Password and Setup Password are

deleted and you need not provide the system password to log on to the computer.

To enter a system setup, press <F2> immediately after a power-on or re-boot.

1. In the System BIOS or System Setup screen, select System Security and press <Enter>.

The System Security screen appears.

2. In the System Security screen, verify that Password Status is Unlocked.

3. Select System Password , enter your system password, and press <Enter> or <Tab>.

Use the following guidelines to assign the system password:

• A password can have up to 32 characters.

• The password can contain the numbers 0 through 9.

• Only lower case letters are valid, upper case letters are not allowed.

• Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).

Re-enter the system password when prompted.

4. Type the system password that you entered earlier and click OK.

5. Select Setup Password, type your system password and press <Enter> or <Tab>.

A message prompts you to re-type the setup password.

6. Type the setup password that you entered earlier and click OK.

7. Press <Esc> and a message prompts you to save the changes.

8. Press <Y> to save the changes.

The computer reboots.

Deleting or Changing an Existing System and/or Setup Password

Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or change

the existing System and/or Setup password. You cannot delete or change an existing System or Setup

password, if the Password Status is Locked.

To enter the System Setup, press <F2> immediately after a power-on or reboot.

1. In the System BIOS or System Setup screen, select System Security and press <Enter>.

The System Security screen is displayed.

2. In the System Security screen, verify that Password Status is Unlocked.

3. Select System Password, alter or delete the existing system password and press <Enter> or <Tab>.

4. Select Setup Password, alter or delete the existing setup password and press <Enter> or <Tab>.

NOTE: If you change the System and/or Setup password, re-enter the new password when

promoted. If you delete the System and/or Setup password, confirm the deletion when

promoted.

5. Press <Esc> and a message prompts you to save the changes.

6. Press <Y> to save the changes and exit from the System Setup.

The computer reboots.

Diagnostics

If you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for

technical assistance. The purpose of running diagnostics is to test your computer's hardware without

requiring additional equipment or risking data loss. If you are unable to fix the problem yourself, service

and support personnel can use the diagnostics results to help you solve the problem.

Enhanced Pre-Boot System Assessment (ePSA)

Diagnostics

The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware.

The ePSA is embedded with the BIOS and is launched by the BIOS internally. The embedded system

diagnostics provides a set of options for particular devices or device groups allowing you to:

• Run tests automatically or in an interactive mode

• Repeat tests

• Display or save test results

• Run thorough tests to introduce additional test options to provide extra information about the failed

device(s)

• View status messages that inform you if tests are completed successfully

• View error messages that inform you of problems encountered during testing

CAUTION: Use the system diagnostics to test only your computer. Using this program with other

computers may cause invalid results or error messages.

NOTE: Some tests for specific devices require user interaction. Always ensure that you are present

at the computer terminal when the diagnostic tests are performed.

1. Power-on the computer.

2. As the computer boots, press the <F12> key as the Dell logo appears.

3. On the boot menu screen, select the Diagnostics option.

The Enhanced Pre-boot System Assessment window is displayed, listing all devices detected in the

computer. The diagnostics starts running the tests on all the detected devices.

4. If you wish to run a diagnostic test on a specific device, press <Esc> and click Yes to stop the

diagnostic test.

5. Select the device from the left pane and click Run Tests.

6. If there are any issues, error codes are displayed.

Note the error code and contact Dell.

Device Status Lights

Table 14. Device Status Lights

Turns on when you turn on the computer and blinks when the computer is in a power

management mode.

Turns on when the computer reads or writes data.

Turns on steadily or blinks to indicate battery charge status.

Turns on when wireless networking is enabled.

The device status LEDs are usually located either on the top or left side of the keyboard. They display the

storage, battery and wireless devices connectivity and activity. Apart from that they can be useful as a

diagnostic tool when there's a possible failure to the system.

The following table lists how to read the LED codes when possible errors occur.

Table 15. LED Lights

Storage LED Power LED Wireless LED Fault Description

Blinking Solid Solid A possible processor failure has occurred.

Solid Blinking Solid The memory modules are detected but encountered

an error.

Blinking Blinking Blinking A system board failure has occurred.

Blinking Blinking Solid A possible graphics card/video failure has occurred.

Blinking Blinking Off System failed on hard drive initialization OR System

failed in Option ROM initialization.

Blinking Off Blinking The USB controller encountered a problem during

initialization.

Solid Blinking Blinking No memory modules are installed/detected.

Blinking Solid Blinking The display encountered a problem during

initialization.

Off Blinking Blinking The modem is preventing the system from completing

POST

Off Blinking Off Memory failed to initialize or memory is unsupported.

Battery Status Lights

If the computer is connected to an electrical outlet, the battery light operates as follows:

Alternately

blinking amber

light and white

light

An unauthenticated or unsupported non-Dell AC adapter is attached to your

laptop.

Alternately

blinking amber

light with

steady white

light

Temporary battery failure with AC adapter present.

Constantly

blinking amber

light

Fatal battery failure with AC adapter present.

Light off Battery in full charge mode with AC adapter present.

White light on Battery in charge mode with AC adapter present.

Specifications

NOTE: Offerings may vary by region. The following specifications are only those required by law to

ship with your computer. For more information about the configuration of your computer, go to

Help and Support in your Windows operating system and select the option to view information

about your computer.

Table 16. System Information

Feature Specification

Chipset Wildcat Point LP

DRAM bus width 64-bit

Flash EPROM SPI 32 Mbits, 64 Mbits

PCIe bus 100 MHz

External Bus Frequency DMI (5GT/s)

Table 17. Processor

Feature Specification

Types Intel Core i3 / i5 / i7

L3 cache 3 MB, 4MB, 6 MB, and 8 MB

Table 18. Memory

Feature Specification

Memory connector Two SODIMM slots

Memory capacity 2GB, 4GB, or 8GB

Memory type DDR3L SDRAM (1600 MHz)

Minimum memory 2 GB

Maximum memory 16 GB

Table 19. Audio

Feature Specification

Type Four-channel high-definition audio

Controller:

Latitude E7250/E7450 Realtek ALC3235

Latitude 7250/7450 Realtek AL3234

Feature Specification

Stereo conversion 24-bit (analog-to-digital and digital-to-analog)

Interface:

Internal High-definition audio

External Microphone-in, stereo headphones, and headset combo

connector

Speakers Two

Internal speaker amplifier 2 W (RMS) per channel

Volume controls Hot keys

Table 20. Video

Feature Specification

Type Integrated on system board

Controller:

UMA Intel HD Graphics 5500

Discrete Nvidia GeForce 840M Graphics

Data bus PCI-E Gen2 x4

External display support • one HDMI

• one mDP

NOTE: Support one VGA, two DP/DVI ports through

Docking station.

Table 21. Camera

Features Specification

Camera Resolution:

HD camera resolution 1280 x 720 pixels (Non-Touch)

FHD camera resolution 1920 x 1080 pixels (Touch)

Video Resolution (maximum) 1280 x 720 pixels

Diagonal viewing angle 74 °

Table 22. Communications

Features Specification

Network adapter 10/100/1000 Mb/s Ethernet (RJ-45)

Wireless Internal wireless local area network (WLAN) and wireless

wide area network (WWAN)

Table 23. Ports and Connectors

Features Specification

Audio One microphone/stereo headphone/speakers connector

Video • one HDMI

• one mDP

Network adapter RJ-45 connector

USB 3.0 One USB 3.0, one PowerShare

Memory card reader Support upto SD4.0

Micro Subscriber Identity Module (uSIM)

card

One

Docking port One

Table 24. Display

Feature Specification

Latitude 7250 Latitude 7450

Type HD FHD W/Touch HD FHD FHD W/Touch

Dimensions:

Height 181.4 mm 194.9 mm 205.6 mm 205.6 mm 215.0 mm

Width 290.5 mm 302.8 mm 320.9 mm 320.9 mm 328.8 mm

Diagonal 3.0 mm 5.95 mm 3.0 mm 3.2 mm 4.15 mm

Maximum

resolution

1366 x 768 1920 x 1080 1366 x 768 1920 x 1080 1920 x 1080

Refresh rate 60 Hz/48 Hz 60 Hz/48 Hz 60 Hz/48 Hz 60 Hz/48 Hz 60 Hz/48 Hz

Minimum

Viewing

Angles:

Horizontal +/-40° +/-80° +/-40° +/-80° +/-80°

Vertical +10°/-30° +/-80° +10°/-30° +/-80° +/-80°

Pixel pitch 0.2025 x 0.2025 0.144 x 0.144 0.2265 x 0.2265 0.161 x 0.161 0.161 x 0.161

Table 25. Keyboard

Feature Specification

Number of keys United States: 82 keys, United Kingdom: 83 keys, Brazil:

84 keys, and Japan: 86keys

Table 26. Touchpad

Feature Specification

Latitude 7250 Latitude 7450

Active Area:

X-axis 99.5 mm 99.5 mm

Y-axis 53.0 mm 53.0 mm

Table 27. Battery

Feature Specification

Type • 3-cell Lithium Polymer battery with ExpressCharge

• 4-cell Lithium Polymer battery with ExpressCharge

Dimensions: Latitude 7250 Latitude 7450

3–cell/4–cell

Depth 80.75 mm (3.18 inches) 74.75 mm (2.94 inches)

Height 7.20 mm (0.28 inch) 8.00 mm (0.31 inch)

Width 282.00 mm (11.10 inches) 308.50 mm (12.15 inches)

Weight:

3-cell 250.00 g (0.55 lb) 247.00 g (0.54 lb)

4–cell 300.00 g (0.66 lb) 308.00 g (0.68 lb)

Voltage

3-cell 11.10 VDC

4–cell 7.40 VDC

Temperature range:

Operating Charge: 0 °C to 50 °C (32 °F to 158 °F)

Discharge: 0 °C to 70 °C ( 32 °F to 122 °F)

Non-Operating –20 °C to 65 °C (4 °F to 149 °F)

Coin-cell battery 3 V CR2032 lithium coin cell

Table 28. AC Adapter

Feature Specification

Type 65 W and 90 W

Input voltage 90 VAC to 264 VAC

Input current (maximum) 1.50 A

Input frequency 47 Hz to 63 Hz

Feature Specification

Output power 65 W and 90 W

Output current 3.34 A and 4.62 A

Rated output voltage 19.5 VDC

Weight 230 g (65 W) and 285 g (90 W)

Dimensions 107*46*29.5 mm (65W) / 130*66 * 22 mm (90W)

Temperature range:

Operating 0 °C to 40 °C (32 °F to 104 °F)

Non-Operating –40 °C to 70 °C (–40 °F to 158 °F)

Table 29. Physical

Feature Latitude 7250 Non-

Touch Latitude 7250 Touch Latitude 7450 Non-

Touch Latitude 7450 Touch

Front

Height

17.8 mm 17.8 mm 18.8 mm 18.8 mm

Back

Height

19.4 mm 21.0 mm 20.4 mm 22.6 mm

Width 310.5 mm (12.22 inches) 337 mm (13.2 inches)

Depth 211.0 mm (8.3 inches) 231.5 mm (9.1 inches)

Weight

(with

3-cell

battery)

1.26 kg (2.79lb) 1.45 kg (3.21lb) 1.55 kg (3.42lb) 1.71 kg (3.77lb)

Light Weight Configurable Items:

Weight

Bound

1.42 kg (3.13lb) 1.57 kg (3.47lb) 1.61 kg (3.56lb) 1.80 kg (3.97lb)

Weight

Target

1.32 kg (2.91lb) 1.52 kg (3.37lb) 1.60 kg (3.54lb) 1.74 kg (3.84lb)

Table 30. Environmental

Feature Specification

Temperature:

Operating 0 °C to 60 °C (32 °F to 140 °F)

Storage –51 °C to 71 °C (–59 °F to 159 °F)

Relative humidity

(maximum):

Operating 10 % to 90 % (non condensing)

Storage 5 % to 95 % (non condensing)

Feature Specification

Altitude (maximum):

Operating –15.2 m to 3048 m (–50 to 10,000 ft)

0° to 35°C

Non-Operating –15.24 m to 10,668 m (–50 ft to 35,000 ft)

Airborne contaminant level G2 or lower as defined by ISA S71.04–1985

Contacting Dell

NOTE: If you do not have an active Internet connection, you can find the contact information on

your purchase invoice, packing slip, bill, or Dell product catalog.

Dell provides several online and telephone-based support and service options. Availability varies by

country and product, and some services may not be available in your area. To contact Dell for sales,

technical support, or customer service issues:

Go to dell.com/contactdell.

Table of Contents

DELL E7450 + 452-11420 User Manual

Related Manuals