DELL M2800 User Manual

Displayed below is the user manual for M2800 by DELL which is a product in the Notebooks category. This manual has pages.

Related Manuals

DELL M2800 Manual

Dell Precision M2800

Owner's Manual

Regulatory Model: P29F

Regulatory Type: P29F001

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of your computer.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you

how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

intellectual property laws. Dell™ and the Dell logo are trademarks of Dell Inc. in the United States and/or other

jurisdictions. All other marks and names mentioned herein may be trademarks of their respective companies.

2014 -04

Rev. A00

Contents

1 Working on Your Computer................................................................................... 7

Before Working Inside Your Computer................................................................................................ 7

Turning Off Your Computer..................................................................................................................9

After Working Inside Your Computer................................................................................................... 9

2 Removing and Installing Components.............................................................. 11

Recommended Tools.......................................................................................................................... 11

System Overview..................................................................................................................................11

Removing the Secure Digital (SD) Card..............................................................................................12

Installing the Secure Digital (SD) Card................................................................................................13

Removing the ExpressCard................................................................................................................. 13

Installing the ExpressCard................................................................................................................... 13

Removing the Battery..........................................................................................................................14

Installing the Battery............................................................................................................................15

Removing the Base Cover...................................................................................................................16

Installing the Base Cover.....................................................................................................................17

Removing the Base-Corner Covers....................................................................................................17

Installing the Base-Corner Covers......................................................................................................18

Removing the Memory........................................................................................................................19

Installing the Memory..........................................................................................................................19

Removing the Hard Drive....................................................................................................................19

Installing the Hard Drive......................................................................................................................21

Removing the Optical Drive................................................................................................................21

Installing the Optical Drive..................................................................................................................22

Removing the Wireless Local Area Network (WLAN) Card................................................................22

Installing the WLAN Card....................................................................................................................23

Removing the Wireless Wide Area Network (WWAN) Card...............................................................23

Installing the WWAN Card...................................................................................................................23

Removing the Network Connector....................................................................................................24

Installing the Network Connector......................................................................................................24

Removing the Coin-Cell Battery........................................................................................................ 25

Installing the Coin-Cell Battery.......................................................................................................... 25

Removing the Power Connector........................................................................................................25

Installing the Power Connector......................................................................................................... 26

Removing the Heat-Sink Assembly.................................................................................................... 27

Installing the Heat-Sink Assembly...................................................................................................... 27

Removing the Processor.....................................................................................................................28

Installing the Processor.......................................................................................................................28

Removing the Keyboard..................................................................................................................... 28

Installing the Keyboard....................................................................................................................... 29

Removing the Palmrest Assembly......................................................................................................30

Installing the Palmrest Assembly........................................................................................................ 33

Removing the WiFi-Switch Board...................................................................................................... 34

Installing the WiFi-Switch Board........................................................................................................ 34

Removing the VGA Board................................................................................................................... 35

Installing the VGA Board..................................................................................................................... 35

Removing the ExpressCard Cage.......................................................................................................36

Installing the ExpressCard Cage.........................................................................................................36

Removing the System Board...............................................................................................................37

Installing the System Board................................................................................................................40

Removing the Speakers.......................................................................................................................41

Installing the Speakers........................................................................................................................ 43

Removing the Display-Hinge Cap......................................................................................................44

Installing the Display-Hinge Cap........................................................................................................44

Removing the Display Assembly.........................................................................................................45

Installing the Display Assembly.......................................................................................................... 48

Removing the Display Bezel...............................................................................................................49

Installing the Display Bezel.................................................................................................................50

Removing the Display Panel................................................................................................................51

Installing the Display Panel................................................................................................................. 53

Removing the Display Hinges.............................................................................................................54

Installing the Display Hinges...............................................................................................................54

Removing the Camera........................................................................................................................ 55

Installing the Camera.......................................................................................................................... 55

3 System Setup............................................................................................................57

Boot Sequence.................................................................................................................................... 57

Navigation Keys................................................................................................................................... 57

System Setup Options.........................................................................................................................58

Updating the BIOS ............................................................................................................................. 66

System and Setup Password...............................................................................................................67

Assigning a System Password and Setup Password.....................................................................67

Deleting or Changing an Existing System and/or Setup Password............................................ 68

4 Diagnostics.............................................................................................................. 69

Enhanced Pre-Boot System Assessment (ePSA) Diagnostics........................................................... 69

Device Status Lights............................................................................................................................ 70

Battery Status Lights............................................................................................................................70

5 Technical Specifications....................................................................................... 73

6 Contacting Dell....................................................................................................... 79

Working on Your Computer

Before Working Inside Your Computer

Use the following safety guidelines to help protect your computer from potential damage and to help to

ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes

that the following conditions exist:

• You have read the safety information that shipped with your computer.

• A component can be replaced or--if purchased separately--installed by performing the removal

procedure in reverse order.

WARNING: Disconnect all power sources before opening the computer cover or panels. After you

finish working inside the computer, replace all covers, panels, and screws before connecting to

the power source.

WARNING: Before working inside your computer, read the safety information that shipped with

your computer. For additional safety best practices information, see the Regulatory Compliance

Homepage at www.dell.com/regulatory_compliance

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or

by periodically touching an unpainted metal surface, such as a connector on the back of the

computer.

CAUTION: Handle components and cards with care. Do not touch the components or contacts

on a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a

processor by its edges, not by its pins.

CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable

itself. Some cables have connectors with locking tabs; if you are disconnecting this type of cable,

press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep

them evenly aligned to avoid bending any connector pins. Also, before you connect a cable,

ensure that both connectors are correctly oriented and aligned.

NOTE: The color of your computer and certain components may appear differently than shown in

this document.

To avoid damaging your computer, perform the following steps before you begin working inside the

computer.

1. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.

2. Turn off your computer (see Turning off Your Computer).

3. If the computer is connected to a docking device (docked), undock it.

CAUTION: To disconnect a network cable, first unplug the cable from your computer and

then unplug the cable from the network device.

4. Disconnect all network cables from the computer.

5. Disconnect your computer and all attached devices from their electrical outlets.

6. Close the display and turn the computer upside-down on a flat work surface.

NOTE: To avoid damaging the system board, you must remove the main battery before you

service the computer.

7. Remove the main battery.

8. Turn the computer top-side up.

9. Open the display.

10. Press the power button to ground the system board.

CAUTION: To guard against electrical shock, always unplug your computer from the

electrical outlet before opening the display.

CAUTION: Before touching anything inside your computer, ground yourself by touching an

unpainted metal surface, such as the metal at the back of the computer. While you work,

periodically touch an unpainted metal surface to dissipate static electricity, which could

harm internal components.

11. Remove any installed ExpressCards or Smart Cards from the appropriate slots.

Turning Off Your Computer

CAUTION: To avoid losing data, save and close all open files and exit all open programs before

you turn off your computer.

1. Shut down the operating system:

• In Windows 8:

– Using a touch-enabled device:

a. Swipe in from the right edge of the screen, opening the Charms menu and select

Settings.

b. Select the and then select Shut down

– Using a mouse:

a. Point to upper-right corner of the screen and click Settings.

b. Click the and select Shut down.

• In Windows 7:

1. Click Start .

2. Click Shut Down.

1. Click Start .

2. Click the arrow in the lower-right corner of the Start menu as shown below, and then click

Shut Down..

2. Ensure that the computer and all attached devices are turned off. If your computer and attached

devices did not automatically turn off when you shut down your operating system, press and hold

the power button for about 4 seconds to turn them off.

After Working Inside Your Computer

After you complete any replacement procedure, ensure you connect any external devices, cards, and

cables before turning on your computer.

CAUTION: To avoid damage to the computer, use only the battery designed for this particular

Dell computer. Do not use batteries designed for other Dell computers.

1. Connect any external devices, such as a port replicator or media base, and replace any cards, such as

an ExpressCard.

2. Connect any telephone or network cables to your computer.

CAUTION: To connect a network cable, first plug the cable into the network device and then

plug it into the computer.

3. Replace the battery.

4. Connect your computer and all attached devices to their electrical outlets.

5. Turn on your computer.

Removing and Installing Components

This section provides detailed information on how to remove or install the components from your

computer.

Recommended Tools

The procedures in this document may require the following tools:

• Small flat-blade screwdriver

• Phillips screwdriver

• Small plastic scribe

System Overview

Figure 1. Back View — Back Cover Removed

1. heat-sink assembly 2. hard drive

3. memory 4. SD card slot

5. ExpressCard slot 6. optical drive

7. coin-cell battery 8. base-corner cover (left)

9. WWAN card 10. WLAN card

11. docking port 12. battery bay

13. base-corner cover (right)

Figure 2. Top View — Keyboard and Palmrest Assembly removed

1. WiFi-switch board 2. speaker

3. ExpressCard cage 4. system board

5. speaker 6. hard-drive bay

7. VGA board 8. display assembly

Removing the Secure Digital (SD) Card

1. Follow the procedures in Before Working Inside your computer.

2. Press in on the SD card to release it from the computer. Slide the SD card out of the computer.

Installing the Secure Digital (SD) Card

1. Slide the SD card into its slot until it clicks into place.

2. Follow the procedures in After Working Inside Your Computer.

Removing the ExpressCard

1. Follow the procedures in Before Working Inside Your Computer.

2. Press in on the ExpressCard to release it from the computer. Slide the ExpressCard out of the

computer.

Installing the ExpressCard

1. Slide the ExpressCard in its slot until it clicks in place.

2. Follow the procedures in After Working Inside Your Computer

Removing the Battery

1. Follow the procedures in Before Working Inside your computer.

2. Slide the release latches to unlock the battery.

3. Flip the battery out of the computer.

Installing the Battery

1. Slide the battery into its slot until it clicks into place.

2. Follow the procedures in After Working Inside Your Computer.

Removing the Base Cover

1. Follow the procedures in Before Working Inside your computer.

2. Remove the screws that secure the base cover to the computer.

3. Lift the base cover and remove it from the computer.

Installing the Base Cover

1. Place the base cover to align with the screw holes on the computer.

2. Tighten the screws to secure the base cover to the computer.

3. Install the battery.

4. Follow the procedures in After Working Inside Your Computer.

Removing the Base-Corner Covers

1. Follow the procedures in Before Working Inside your computer.

2. Remove the battery.

3. Remove the base cover.

4. Remove the screws that secure the left base-corner cover, lift and remove it from the computer.

5. Remove the screws that secure the right base-corner cover, lift and remove it from the computer.

Installing the Base-Corner Covers

1. Place the left and right base-corner covers to align with the screw holes on the computer.

2. Tighten the screws to secure the base-corner covers to the computer.

3. Install:

a. base cover

b. battery

4. Follow the procedures in After Working Inside Your Computer.

Removing the Memory

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. base cover

3. Pry the securing clips away from the memory module until it pops-up and remove the memory

module from its connector on the system board.

Installing the Memory

1. Insert the memory into the memory socket.

2. Press the securing clips to secure the memory module to the system board.

3. Install:

a. base cover

b. battery

4. Follow the procedures in After Working Inside Your Computer.

Removing the Hard Drive

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the battery.

3. Remove the screws that secure the hard drive to the computer. Slide the hard drive out of the

computer.

4. Remove the screw that secures the hard-drive caddy to the hard drive. Remove the hard-drive caddy

from the hard drive.

5. Flex the hard-drive isolation. Peel off the hard-drive isolation from the hard drive.

Installing the Hard Drive

1. Install the hard-drive isolation on the hard drive.

2. Attach the hard-drive caddy to the hard drive.

3. Tighten the screws to secure the hard-drive caddy to the hard drive.

4. Slide the hard drive into the computer.

5. Tighten the screws to secure the hard drive to the computer.

6. Install the battery.

7. Follow the procedures in After Working Inside Your Computer.

Removing the Optical Drive

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the battery.

3. Press the optical-drive latch to release the optical drive and pull the optical drive from the computer.

4. Remove the screw that secures the optical-drive latch to the optical drive. Slide the optical-drive

latch and remove it from the optical-drive.

5. Remove the screws that secure the optical-drive latch bracket to the optical drive. Remove the latch

bracket from the optical drive.

Installing the Optical Drive

1. Align the optical-drive latch bracket to its position on the optical drive.

2. Tighten the screw to secure the optical-drive latch bracket to the optical drive.

3. Slide the optical-drive latch in the optical-drive latch bracket.

4. Tighten the screws to secure the optical-drive latch to the optical-drive latch bracket.

5. Slide the optical drive into the drive bay.

6. Press the optical-drive latch to secure the optical drive.

7. Install the battery.

8. Follow the procedures in After Working Inside Your Computer.

Removing the Wireless Local Area Network (WLAN) Card

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. base cover

3. Disconnect the antenna cables, remove the screw that secures the WLAN card to the computer, and

lift the WLAN card from the computer.

Installing the WLAN Card

1. Insert the WLAN card in its connector at a 45–degree angle in its slot.

2. Tighten the screw to secure the WLAN card to the computer.

3. Connect the antenna cables to their respective connectors marked on the WLAN card.

4. Install:

a. base cover

b. battery

5. Follow the procedures in After Working Inside Your Computer.

Removing the Wireless Wide Area Network (WWAN) Card

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. base cover

3. Perform the following steps as shown in the illustration:

a. Disconnect the antenna cables from the WWAN card.

b. Remove the screw that secures the WWAN card to the computer.

c. Remove the WWAN card from the computer.

Installing the WWAN Card

1. Place the WWAN card in its slot in the system board.

2. Press the WWAN card down and tighten the screw to secure the WWAN card to the computer.

3. Connect the antenna cables to their connectors on the WWAN card.

4. Install:

a. base cover

b. battery

5. Follow the procedures in After Working Inside Your Computer.

Removing the Network Connector

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. base cover

c. base-corner cover (left)

3. Perform the following steps as shown in the illustration:

a. Disconnect the cable from the system board.

b. Release cable from the routing channel.

c. Remove the screw that secures the network-connector bracket to the computer.

4. Lift the network-connector bracket from the computer. Lift the network connector from the

computer.

Installing the Network Connector

1. Align the network connector to its position on the computer.

2. Place the network-connector bracket on the network connector.

3. Tighten the screw to secure the network-connector bracket to the computer.

4. Route the cable through the routing channel.

5. Connect the cable to the system board.

6. Install:

a. base-corner cover (left)

b. base cover

c. battery

7. Follow the procedures in After Working Inside Your Computer.

Removing the Coin-Cell Battery

1. Follow the procedures in Before Working Inside your computer.

2. Remove:

a. battery

b. base cover

3. Disconnect the coin-cell battery cable, pry the coin-cell battery upward, and remove the coin-cell

from the computer.

Installing the Coin-Cell Battery

1. Place the coin-cell battery in its slot.

2. Connect the coin-cell battery cable to the system board.

3. Install:

a. base cover

b. battery

4. Follow the procedures in After Working Inside Your Computer.

Removing the Power Connector

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. base-corner cover (right)

c. base cover

3. Perform the following steps as shown in the illustration:

a. Disconnect the power-connector cable from the system board.

b. Release the power-connector cable from the routing channel.

c. Remove the screw that secures the power-connector bracket to the computer.

4. Lift the power-connector bracket from the computer. Lift the power connector from the computer.

Installing the Power Connector

1. Align the power connector to its position in the computer.

2. Place the power-connector bracket on the power connector.

3. Tighten the screw to secure the power-connector bracket to the computer.

4. Route the cable through the routing channel.

5. Connect the cable to the system board.

6. Install:

a. base cover

b. base-corner cover (right)

c. battery

7. Follow the procedures in After Working Inside Your Computer.

Removing the Heat-Sink Assembly

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. base cover

3. Disconnect the fan cable and remove the screws that secure the heat-sink assembly to the system

board.

4. Perform the following steps as shown in the illustration:

a. Slide the heat-sink assembly.

b. Lift the heat-sink assembly from the computer.

Installing the Heat-Sink Assembly

1. Slide the heat-sink assembly to its position on the system board.

2. Tighten the screws to secure the heat-sink assembly to the system board.

3. Connect the fan cable to the system board.

4. Install:

a. base cover

b. battery

5. Follow the procedures in After Working Inside Your Computer.

Removing the Processor

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. base cover

c. heatsink

3. Rotate the processor-cam lock in a counter-clockwise direction. Remove the processor from the

computer.

Installing the Processor

1. Align the notches on the processor and the socket, and insert the processor into the socket.

2. Rotate the processor-cam lock in a clockwise direction.

3. Install:

a. heatsink

b. base cover

c. battery

4. Follow the procedures in After Working Inside Your Computer.

Removing the Keyboard

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the battery.

3. Using a plastic scribe, pry under the keyboard trim and then along the sides and bottom to release it

from the computer. Lift and remove the keyboard trim from the computer.

4. Remove the screws that secure the keyboard to the palmrest assembly, lift and flip the keyboard to

access the keyboard-cable.

5. Disconnect the keyboard cable from the system board.

Installing the Keyboard

1. Connect the keyboard cable to the system board.

2. Slide the keyboard into its compartment and until it clicks into place.

3. Tighten the screws to secure the keyboard to the palmrest assembly.

4. Align the keyboard trim on its compartment and press along the sides until it snaps in place.

5. Install the battery.

6. Follow the procedures in After Working Inside Your Computer.

Removing the Palmrest Assembly

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. SD card

b. ExpressCard

c. battery

d. keyboard

e. display-hinge cap

f. base cover

g. base-corner covers

3. Remove the screws that secure the palmrest assembly to the base of the computer.

4. Flip the computer and remove the screws that secure the palmrest assembly to the computer.

5. Disconnect the following cables:

a. fingerprint-reader

b. touchpad

c. power-button

6. Pry the palmrest assembly upwards and remove it from the computer.

Installing the Palmrest Assembly

1. Align the palmrest assembly to its original position in the computer and snap it into place.

2. Tighten the screws to secure the palmrest assembly to the computer.

3. Connect the following cables:

a. power-button

b. touchpad

c. fingerprint-reader

4. Flip the computer and tighten the screws to secure the palmrest assembly to the base of the

computer.

5. Install:

a. base-corner covers

b. base cover

c. display-hinge cap

d. keyboard

e. battery

f. ExpressCard

g. SD card

6. Follow the procedures in After Working Inside Your Computer.

Removing the WiFi-Switch Board

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. SD card

b. ExpressCard

c. battery

d. keyboard

e. display-hinge cap

f. base cover

g. base-corner covers

h. palmrest assembly

3. Perform the following steps as shown in the illustration:

a. Disconnect the cable from the system board.

b. Remove the screw that secures the WiFi-switch board and lift it from the computer.

Installing the WiFi-Switch Board

1. Place the WiFi-switch board in its slot.

2. Tighten the screw to secure the WiFi-switch board to the computer.

3. Connect the cable to the system board.

4. Install:

a. palmrest assembly

b. base cover

c. base-corner covers

d. display-hinge cap

e. keyboard

f. battery

g. ExpressCard

h. SD card

5. Follow the procedures in After Working Inside Your Computer.

Removing the VGA Board

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. SD card

b. ExpressCard

c. battery

d. keyboard

e. display-hinge cap

f. base cover

g. base-corner covers

h. palmrest assembly

3. Remove the screws that secure the VGA board to the computer and remove it from its connector.

Installing the VGA Board

1. Insert the VGA board in its slot

2. Tighten the screws to secure the VGA board to the computer.

3. Install:

a. palmrest assembly

b. base-corner covers

c. base cover

d. display-hinge cap

e. keyboard

f. battery

g. ExpressCard

h. SD card

4. Follow the procedures in After Working Inside Your Computer.

Removing the ExpressCard Cage

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. SD card

b. ExpressCard

c. battery

d. keyboard

e. display-hinge cap

f. base cover

g. base-corner covers

h. Palmrest Assembly

3. Remove the screws that secure the ExpressCard cage to the computer. Remove the ExpressCard

cage from the computer.

Installing the ExpressCard Cage

1. Place the ExpressCard cage in its slot.

2. Tighten the screws to secure the ExpressCard cage to the computer.

3. Install:

a. palmrest assembly

b. base-corner covers

c. base cover

d. display-hinge cap

e. keyboard

f. battery

g. ExpressCard

h. SD card

4. Follow the procedures in After Working Inside Your Computer.

Removing the System Board

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. SD card

b. ExpressCard

c. battery

d. keyboard

e. hard drive

f. optical drive

g. display-hinge cap

h. base cover

i. base-corner covers

j. power connector

k. coin cell

l. memory

m. WLAN card

n. WWAN card

o. heatsink

p. processor

q. VGA board

r. ExpressCard cage

3. Perform the following steps as shown in the illustration:

a. Disconnect the WiFi-switch from the system board.

b. Disconnect the speaker cables from the system board.

4. Remove the screws that secure the system board to the computer.

5. Lift the system board from the computer.

Installing the System Board

1. Place the system board to align with the ports on the computer.

2. Tighten the screws to secure the system board.

3. Connect the following cables to the system board:

a. speaker

b. WiFi-switch

4. Install:

a. ExpressCard cage

b. VGA board

c. processor

d. heatsink

e. WWAN card

f. WLAN card

g. memory

h. coin-cell battery

i. power connector

j. base-corner covers

k. base cover

l. display-hinge cap

m. optical drive

n. hard drive

o. keyboard

p. battery

q. ExpressCard

r. SD card

5. Follow the procedures in After Working Inside Your Computer.

Removing the Speakers

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. SD card

b. ExpressCard

c. battery

d. keyboard

e. hard drive

f. optical drive

g. display-hinge cap

h. base cover

i. base-corner covers

j. palmrest assembly

k. power connector

l. coin cell

m. memory

n. WLAN card

o. WWAN card

p. heatsink

q. processor

r. VGA board

s. ExpressCard cage

t. system board

3. Remove the speaker cable from the routing channels. Remove the screws that secure the speakers

to the computer.

4. Lift the speakers from the computer.

Installing the Speakers

1. Align the speakers in its position on the computer and route the speaker cable in the routing

channels on the computer.

2. Tighten the screws to secure the speakers.

3. Install:

a. system board

b. ExpressCard cage

c. VGA board

d. processor

e. heatsink

f. WWAN card

g. WLAN card

h. memory

i. coin-cell battery

j. power connector

k. palmrest assembly

l. base-corner covers

m. base cover

n. display-hinge cap

o. optical drive

p. hard drive

q. keyboard

r. battery

s. ExpressCard

t. SD card

4. Follow the procedures in After Working Inside Your Computer.

Removing the Display-Hinge Cap

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the battery.

3. Remove the screws that secure the display-hinge cap to the computer and remove the display-hinge

cap from the computer.

Installing the Display-Hinge Cap

1. Align the display-hinge cap with the screw holes.

2. Tighten the screws to secure the display-hinge cap to the computer.

3. Install the battery.

4. Follow the procedures in After Working Inside Your Computer.

Removing the Display Assembly

1. Follow the procedures in Before Working Inside your computer.

2. Remove:

a. battery

b. display-hinge cap

c. base cover

d. base-corner covers

3. Disconnect the antenna cables connected to the WLAN card and release it from the routing channel.

Disconnect the camera cable from the system board.

4. Disconnect the LVDS cable and release the LVDS cable and camera cable from the routing channel.

Remove them from the computer.

5. Remove the screws that secure the display assembly to the computer.

6. Remove the display assembly from the computer.

Installing the Display Assembly

1. Place the display assembly in its position on the computer.

2. Tighten the screws to secure the display assembly.

3. Route the LVDS cable and the camera cable through the routing channel.

4. Route the antenna cables through the routing channel.

5. Connect the antenna cables to the WLAN card on the computer.

6. Connect the camera cable to the computer.

7. Install:

a. base-corner covers

b. base cover

c. display-hinge cap

d. battery

8. Follow the procedures in After Working Inside Your Computer.

Removing the Display Bezel

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. display-hinge cap

c. base cover

d. base-corner covers

e. display assembly

3. Pry up along the edges to release the display bezel.

4. Remove the display bezel from the display assembly.

Installing the Display Bezel

1. Place the display bezel onto the display assembly.

2. Starting from the top corner, press on the display bezel and work around the entire bezel until it

clicks onto the display assembly.

3. Press on the left and right edges of the display bezel.

4. Install:

a. display assembly

b. base-corner covers

c. base cover

d. display-hinge cap

e. battery

5. Follow the procedures in After Working Inside Your Computer.

Removing the Display Panel

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. display-hinge cap

c. base cover

d. base-corner covers

e. display assembly

f. display bezel

3. Remove the screws that secure the display panel to the display assembly.

4. Flip the display panel over.

5. Peel off the LVDS cable-connector tape and disconnect the LVDS cable from the display panel.

Remove the display panel from the display assembly.

Installing the Display Panel

1. Connect the LVDS cable and stick the LVDS cable-connector tape.

2. Flip the display and place it in the display assembly.

3. Tighten the screws to secure the display panel to the display assembly.

4. Install:

a. display bezel

b. display assembly

c. base-corner covers

d. base cover

e. display-hinge cap

f. battery

5. Follow the procedures in After Working Inside Your Computer.

Removing the Display Hinges

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. display-hinge cap

c. base cover

d. base-corner covers

e. display assembly

f. display bezel

g. display panel

3. Perform the following steps as shown in the illustration:

a. Remove the screws that secure the display hinges to the display assembly.

b. Remove the display hinges from the computer.

Installing the Display Hinges

1. Place the display hinges in its location on the computer.

2. Tighten the screws to secure the display hinges to the display assembly.

3. Install:

a. display panel

b. display bezel

c. display assembly

d. base-corner covers

e. base cover

f. display-hinge cap

g. battery

4. Follow the procedures in After Working Inside Your Computer.

Removing the Camera

1. Follow the procedures in Before Working Inside your computer.

2. Remove:

a. battery

b. display assembly

c. display bezel

3. Perform the following steps to remove the camera:

a. Disconnect the camera cable.

b. Remove the screw that secures the camera module.

c. Lift the camera module from the computer.

Installing the Camera

1. Place the camera module in its slot in the computer.

2. Tighten the screw to secure the camera to the display assembly.

3. Connect the camera cable.

4. Install:

a. display bezel

b. display assembly

c. battery

5. Follow the procedures in After Working Inside Your Computer.

System Setup

System Setup enables you to manage your computer hardware and specify BIOS‐level options. From the

System Setup, you can:

• Change the NVRAM settings after you add or remove hardware

• View the system hardware configuration

• Enable or disable integrated devices

• Set performance and power management thresholds

• Manage your computer security

Boot Sequence

Boot Sequence allows you to bypass the System Setup‐defined boot device order and boot directly to a

specific device (for example: optical drive or hard drive). During the Power-on Self Test (POST), when the

Dell logo appears, you can:

• Access System Setup by pressing <F2> key

• Bring up the one-time boot menu by pressing <F12> key

The one-time boot menu displays the devices that you can boot from including the diagnostic option.

The boot-menu options are:

• Removable Drive (if available)

• STXXXX Drive

NOTE: XXX denotes the SATA drive number.

• Optical Drive

• Diagnostics

NOTE: Choosing Diagnostics, will display the ePSA diagnostics screen.

The boot sequence screen also displays the option to access the System Setup screen.

Navigation Keys

The following table displays the system setup navigation keys.

NOTE: For most of the system setup options, changes that you make are recorded but do not take

effect until you re-start the system.

Table 1. Navigation Keys

Keys Navigation

Up arrow Moves to the previous field.

Down arrow Moves to the next field.

<Enter> Allows you to select a value in the selected field (if applicable) or follow the link in

the field.

Spacebar Expands or collapses a drop‐down list, if applicable.

<Tab> Moves to the next focus area.

NOTE: For the standard graphics browser only.

<Esc> Moves to the previous page till you view the main screen. Pressing <Esc> in the main

screen displays a message that prompts you to save any unsaved changes and

restarts the system.

<F1> Displays the System Setup help file.

System Setup Options

NOTE: Depending on your computer and its installed devices, the items listed in this section may or

may not appear.

Table 2. General

Option Description

System Information This section lists the primary hardware

features of your computer.

• System Information

• Memory Information

• Processor Information

• Device Information

Battery Information Displays the charge status of the battery.

Boot Sequence Allows you to change the order in which

the computer attempts to find an

operating system. All the below options

are selected.

• Diskette Drive

• Internal HDD

• Onboard NIC

• USB Storage Device

• CD/DVD/CD-RW Drive

You can also choose the Boot List

option. The options are:

•Legacy (Default Setting)

• UEFI

Option Description

Advanced Boot Options Allows you to configure your system for

legacy boot mode. The option is enables

by default.

Date/Time Allows you to set the date and time.

Table 3. System Configuration

Option Description

Integrated NIC Allows you to configure the integrated

network controller. The options are:

• Disabled

• Enabled

•Enabled w/PXE (Default Setting)

Parallel Port Allows you to define and set how the

parallel port on the docking station

operates. You can set the parallel port

to:

• Disabled

•AT (Default Setting)

• PS2

• ECP

Serial Port Identifies and defines the serial port

settings. You can set the serial port to:

• Disabled

•COM1 (Default Setting)

• COM2

• COM3

• COM4

NOTE: The operating system may

allocate resources even if the

setting is disabled.

SATA Operation Allows you to configure the internal

SATA hard-drive controller. The options

are:

• Disabled

• ATA

• AHCI

•RAID On (Default Setting)

NOTE: SATA is configured to

support RAID mode.

Drives Allows you to configure the SATA drives

on board. The options are:

• SATA-0

• SATA-1

Option Description

• SATA-4

• SATA-5

Default Setting: All drives are enabled.

SMART Reporting This field controls if the hard drive errors

for the integrated drives are reported

during system startup. This technology

is part of the SMART (Self Monitoring

Analysis and Reporting Technology)

specification. This option is disabled by

default.

•Enable SMART Reporting

USB Configuration Allows you to define the USB

configuration. The options are:

• Enable Boot Support

• Enable External USB Port

Default Setting: Both the options are

enabled.

USB PowerShare Allows you to configure the behavior of

the USB PowerShare feature. The option

is disabled by default.

• Enable USB PowerShare

Audio Allows you to enable or disable the

integrated audio controller. The option

is enabled by default.

Keyboard Illumination Allows you to choose the operating

mode of the keyboard illumination

feature. The options are:

•Disabled (Default Setting)

• Level is 25%

• Level is 50%

• Level is 75%

• Level is 100%

Unobtrusive Mode Allows you to set the mode that will turn

off all light and sound emissions from

the system. The option is disabled by

default.

Miscellaneous Devices Allows you enable or disable the various

on board devices. The options are:

• Enable Internal Modem

• Enable Microphone

• Enable Camera

• Enable Module Bay

• Enable ExpressCard

Option Description

• Enable Hard Drive Free Fall

Protection

Default Setting: All devices are enabled

You can select if you want to enable or

disable media card. The options are:

•Enable Media Card (Default Setting)

• Disable Media Card

Table 4. Video

Option Description

LCD Brightness Allows you to set the panel brightness when the ambient sensor is Off.

Table 5. Security

Option Description

Admin Password Allows you to set, change, or delete the administrator (admin)

password.

NOTE: You must set the admin password before you set the

system or hard drive password.

NOTE: Successful password changes take effect immediately.

NOTE: Deleting the admin password automatically deletes the

system password and the hard drive password.

NOTE: Successful password changes take effect immediately.

Default Setting: Not set

System Password Allows you to set, change or delete the system password.

NOTE: Successful password changes take effect immediately.

Default Setting: Not set

Strong Password Allows you to enforce the option to always set strong passwords.

Default Setting: Enable Strong Password is not selected.

Password Configuration You can define the length of your password. Min = 4 , Max = 32

Password Bypass Allows you to enable or disable the permission to bypass the System

and the Internal HDD password, when they are set. The options are:

•Disabled (Default Setting)

• Reboot bypass

Password Change Allows you to enable the disable permission to the System and Hard

Drive passwords when the admin password is set.

Allow Non-Admin Password Changes (Default Setting)

Option Description

Non-Admin Setup Changes Allows you to determine whether changes to setup option are

permitted when an administrator password is set. The option is disabled

by default.

TPM Security Allows you to enable the Trusted Platform Module (TPM) during POST.

The option is disabled by default.

Computrace Allows you to activate or disable the optional Computrace software The

options are:

•Deactivate (Default Setting)

• Disable

• Activate

NOTE: The Activate and Disable options will permanently activate

or disable the feature and no further changes will be allowed

CPU XD Support Allows you to enable the Execute Disable mode of the processor.

Enable CPU XD Support(Default Setting)

OROM Keyboard Access Allows you to set access to enter the Option ROM Configuration

screens using hotkeys during boot process. The options are:

•Enable (Default Setting)

• One Time Enable

• Disable

Admin Setup Lockout Allows you to prevent users from entering Setup when an Administrator

password is set. The option is disables by default.

Table 6. Secure Boot

Option Description

Secure Boot Enable Allows you to enable or disable the secure boot feature. The options are:

•Disabled (Default Setting)

• Enabled

Table 7. Performance

Option Description

Multi Core Support This field specifies whether the process

will have one or all cores enabled. The

performance of some applications will

improve with the additional cores. This

option is enabled by default. Allows you

to enable or disable multi-core support

for the processor. The options are:

•All (Default Setting)

• 1

• 2

Intel SpeedStep Allows you to enable or disable the Intel

SpeedStep feature.

Option Description

Default Setting: Enable Intel SpeedStep

C States Control Allows you to enable or disable the

additional processor sleep states. The

option is enabled by default.

Limit CPUID Allows you to limit the maximum value

the processor standard CPUID function

will support. The option is disabled by

default.

Intel TurboBoost Allows you to enable or disable the Intel

TurboBoost mode of the processor.

Default Setting: Enable Intel

TurboBoost

Hyper-Thread Control Allows you to enable or disable the

HyperThreading in the processor.

Default Setting: Enabled

Rapid Start Technology Allows you to set the rapid start time.

The option is set by default.

Table 8. Power Management

Option Description

AC Behavior Allows the computer to power-uon automatically, when AC adapter is

plugged. The option is disabled.

• Wake on AC

Auto On Time Allows you to set the time at which the computer must turn on

automatically. The options are:

•Disabled (Default Setting)

• Every Day

• Weekdays

Deep Sleep Control Allows you to set where deep sleep is enabled. The options are:

•Disabled (Default Setting)

• Enabled in S5 only

• Enabled in S4 and S5

USB Wake Support Allows you to enable the USB devices to wake the computer from

standby mode. The option is disabled

• Enable USB Wake Support

Wireless Radio Control Allows you to control the WLAN and WWAN radio. The options are:

• Control WLAN radio

• Control WWAN radio

Default Setting: Both the options are disabled.

Option Description

Wake on LAN/WLAN This option allows the computer to power up from the off state when

triggered by a special LAN signal. Wake-up from the Standby state is

unaffected by this setting and must be enabled in the operating system.

This feature only works when the computer is connected to AC power

supply.

•Disabled - Does not allow the system to power on by special LAN

signals when it receives a wake-up signal from the LAN or wireless

LAN. (Default Setting)

• LAN Only - Allows the system to be powered on by special LAN

signals.

• WLAN Only

• LAN or WLAN

Block Sleep Allows you to block the computer from entering into the sleep state.

Option is disabled by default.

• Block Sleep (S3)

Peak Shift Allows you to set the peak shift. The option is disabled by default.

Advanced Battery Charge

Configuration

Allows you to enable the advance battery charge mode. The option is

disabled by default.

Primary Battery Charge

Configuration

Allows you to define how to use the battery charge, when AC is plugged

in. The options are:

•Adaptive (Default Setting)

• Standard

• Express Charge

• Primarily AC use

• Custom

Battery Slice Charge

Configuration

Allows you to define the how to charge the battery. The options are:

• Standard Charge

•Express Charge (Default Setting)

Module Bay Battery Charge

Configuration

Allows you to define how to charge the battery at standard rate. The

options are:

• Standard

•Express Charge (Default Setting)

NOTE: Disable the Advanced Battery Charge Mode in order to

enable this opiton.

Intel(R) Smart Connect

Technology

Allows you to enable the system to sense nearby wireless connection

while the system is asleep. The option is disabled by default.

Table 9. POST Behavior

Option Description

Adapter Warnings Allows you to activate the adapter warning messages when certain

power adapters are used. The option is enabled by default.

Option Description

• Enable Adapter Warnings

Mouse/Touchpad Allows you to define how the computer handles the mouse and

touchpad input. The options are:

• Serial Mouse

• PS2 Mouse

•Touchpad/PS-2 Mouse (Default Setting)

Numlock Enable Specifies if the NumLock function can be enabled when the computer

boots. This option is enabled by default.

• Enable Numlock

Fn Key Emulation Allows you to match the <Scroll Lock> key feature of PS-2 keyboard with

the <Fn> key feature in an internal keyboard. The option is enabled by

default.

• Enable Fn Key Emulation

Keyboard Errors Specifies whether keyboard related errors are reported when it boots.

This option is enabled by default.

• Enable Keyboard Error Detection

Fastboot Allows you to speed up the boot processes. The options are:

• Minimal

•Thorough (Default Setting)

• Auto

Extend BIOS POST Time Allows you to create an additional pre-boot delay. The options are:

•0 seconds (Default Setting)

• 5 seconds

• 10 seconds

MEBx Hotkey Allows you to enable the MEBx hotkey function if required. The options

is enabled by default.

Table 10. Virtualization Support

Option Description

Virtualization This option specifies whether a Virtual Machine Monitor (VMM) can

utilize the additional hardware capabilities provided by Intel Virtualization

technology.

•Enable Intel Virtualization Technology - Default Setting.

VT for Direct I/O Enables or disables the Virtual Machine Monitor (VMM) from utilizing the

additional hardware capabilities provided by Intel Virtualization

technology for direct I/O.

•Enable Intel Virtualization Technology for Direct I/O - Default

Setting.

Trusted Execution Allows you to specify if additional hardware capabilities can be utilized.

The option is disabled by default.

Option Description

NOTE: The TPM, Virtualization Technology, andVirtualization

Technology for Direct I/O must be enabled to use this feature.

Table 11. Wireless

Option Description

Wireless Switch Allows you to determine which wireless device can be controlled by the

wireless switch. The options are:

• WWAN

• WiGig

• WLAN

• Bluetooth

All options are enabled by default.

Wireless Device Enable Allows you to enable or disable the wireless devices. The options are:

• WWAN

• Bluetooth

• WLAN/WiGig

All options are enabled by default.

Table 12. Maintenance

Option Description

Service Tag Displays the service tag of your computer.

Asset Tag Allows you to create a system asset tag if an asset tag is not already set.

This option is not set by default.

Table 13. System Logs

Option Description

BIOS events Displays the system event log and allows you to clear the log.

Thermal Events Displays the thermal events and allows you to clear the log.

Power Events Displays the power events and allows you to clear the log.

Updating the BIOS

It is recommended to update your BIOS (system setup), on replacing the system board or if an update is

available. For laptops, ensure that your computer battery is fully charged and connected to a power

outlet

1. Re-start the computer.

2. Go to dell.com/support.

3. Enter the Service Tag or Express Service Code and click Submit.

NOTE: To locate the Service Tag, click Where is my Service Tag?

NOTE: If you cannot find your Service Tag, click Detect My Product. Proceed with the

instructions on screen.

4. If you are unable to locate or find the Service Tag, click the Product Category of your computer.

5. Choose the Product Type from the list.

6. Select your computer model and the Product Support page of your computer appears.

7. Click Get drivers and click View All Drivers.

The Drivers and Downloads page opens.

8. On the Drivers and Downloads screen, under the Operating System drop-down list, select BIOS.

9. Identify the latest BIOS file and click Download File.

You can also analyze which drivers need an update. To do this for your product, click Analyze

System for Updates and follow the instructions on the screen.

10. Select your preferred download method in the Please select your download method below

window; click Download File.

The File Download window appears.

11. Click Save to save the file on your computer.

12. Click Run to install the updated BIOS settings on your computer.

Follow the instructions on the screen.

System and Setup Password

You can create a system password and a setup password to secure your computer.

Password Type Description

System password Password that you must enter to log on to your system.

Setup password Password that you must enter to access and make changes to the BIOS settings of

your computer.

CAUTION: The password features provide a basic level of security for the data on your computer.

CAUTION: Anyone can access the data stored on your computer if it is not locked and left

unattended.

NOTE: Your computer is shipped with the system and setup password feature disabled.

Assigning a System Password and Setup Password

You can assign a new System Password and/or Setup Password or change an existing System Password

and/or Setup Password only when Password Status is Unlocked. If the Password Status is Locked, you

cannot change the System Password.

NOTE: If the password jumper is disabled, the existing System Password and Setup Password is

deleted and you need not provide the system password to log on to the computer.

To enter a system setup, press <F2> immediately after a power-on or re-boot.

1. In the System BIOS or System Setup screen, select System Security and press <Enter>.

The System Security screen appears.

2. In the System Security screen, verify that Password Status is Unlocked.

3. Select System Password , enter your system password, and press <Enter> or <Tab>.

Use the following guidelines to assign the system password:

• A password can have up to 32 characters.

• The password can contain the numbers 0 through 9.

• Only lower case letters are valid, upper case letters are not allowed.

• Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).

Re-enter the system password when prompted.

4. Type the system password that you entered earlier and click OK.

5. Select Setup Password, type your system password and press <Enter> or <Tab>.

A message prompts you to re-type the setup password.

6. Type the setup password that you entered earlier and click OK.

7. Press <Esc> and a message prompts you to save the changes.

8. Press <Y> to save the changes.

The computer reboots.

Deleting or Changing an Existing System and/or Setup Password

Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or change

the existing System and/or Setup password. You cannot delete or change an existing System or Setup

password, if the Password Status is Locked.

To enter the System Setup, press <F2> immediately after a power-on or reboot.

1. In the System BIOS or System Setup screen, select System Security and press <Enter>.

The System Security screen is displayed.

2. In the System Security screen, verify that Password Status is Unlocked.

3. Select System Password, alter or delete the existing system password and press <Enter> or <Tab>.

4. Select Setup Password, alter or delete the existing setup password and press <Enter> or <Tab>.

NOTE: If you change the System and/or Setup password, re-enter the new password when

promoted. If you delete the System and/or Setup password, confirm the deletion when

promoted.

5. Press <Esc> and a message prompts you to save the changes.

6. Press <Y> to save the changes and exit from the System Setup.

The computer reboots.

Diagnostics

If you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for

technical assistance. The purpose of running diagnostics is to test your computer's hardware without

requiring additional equipment or risking data loss. If you are unable to fix the problem yourself, service

and support personnel can use the diagnostics results to help you solve the problem.

Enhanced Pre-Boot System Assessment (ePSA)

Diagnostics

The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware.

The ePSA is embedded with the BIOS and is launched by the BIOS internally. The embedded system

diagnostics provides a set of options for particular devices or device groups allowing you to:

• Run tests automatically or in an interactive mode

• Repeat tests

• Display or save test results

• Run thorough tests to introduce additional test options to provide extra information about the failed

device(s)

• View status messages that inform you if tests are completed successfully

• View error messages that inform you of problems encountered during testing

CAUTION: Use the system diagnostics to test only your computer. Using this program with other

computers may cause invalid results or error messages.

NOTE: Some tests for specific devices require user interaction. Always ensure that you are present

at the computer terminal when the diagnostic tests are performed.

1. Power-on the computer.

2. As the computer boots, press the <F12> key as the Dell logo appears.

3. On the boot menu screen, select the Diagnostics option.

The Enhanced Pre-boot System Assessment window is displayed, listing all devices detected in the

computer. The diagnostics starts running the tests on all the detected devices.

4. If you wish to run a diagnostic test on a specific device, press <Esc> and click Yes to stop the

diagnostic test.

5. Select the device from the left pane and click Run Tests.

6. If there are any issues, error codes are displayed.

Note the error code and contact Dell.

Device Status Lights

Table 14. Device Status Lights

Turns on when you turn on the computer and blinks when the computer is in a power

management mode.

Turns on when the computer reads or writes data.

Turns on steadily or blinks to indicate battery charge status.

Turns on when wireless networking is enabled.

The device status LEDs are usually located either on the top or left side of the keyboard. They are used to

display the storage, battery and wireless devices connectivity and activity. Apart from that they can be

useful as a diagnostic tool when there's a possible failure to the system.

The following table lists how to read the LED codes when possible errors occur.

Table 15. LED Lights

Storage LED Power LED Wireless LED Fault Description

Blinking Solid Solid A possible processor failure has occurred.

Solid Blinking Solid The memory modules are detected but has

encountered an error.

Blinking Blinking Blinking A system board failure has occurred.

Blinking Blinking Solid A possible graphics card/video failure has occurred.

Blinking Blinking Off System failed on hard drive initialization OR System

failed in Option ROM initialization.

Blinking Off Blinking The USB controller encountered a problem during

initialization.

Solid Blinking Blinking No memory modules are installed/detected.

Blinking Solid Blinking The display encountered a problem during

initialization.

Off Blinking Blinking The modem is preventing the system from completing

POST

Off Blinking Off Memory failed to initialize or memory is unsupported.

Battery Status Lights

If the computer is connected to an electrical outlet, the battery light operates as follows:

Alternately

blinking amber

light and white

light

An unauthenticated or unsupported non-Dell AC adapter is attached to your

laptop.

Alternately

blinking amber

light with

steady white

light

Temporary battery failure with AC adapter present.

Constantly

blinking amber

light

Fatal battery failure with AC adapter present.

Light off Battery in full charge mode with AC adapter present.

White light on Battery in charge mode with AC adapter present.

Technical Specifications

NOTE: Offerings may vary by region. The following specifications are only those required by law to

ship with your computer. For more information about the configuration of your computer, go to

Help and Support in your Windows operating system and select the option to view information

about your computer.

Table 16. System Information

Feature Specification

Chipset Mobile Intel QM87 Express Chipset

DRAM bus width 64-bit

Flash EPROM SPI 32 Mbits, 64 Mbits

PCIe bus 100 MHz

External Bus Frequency PCIe Gen2 (5GT/s)

Table 17. Processor

Feature Specification

Types Intel Core i5 / i7series

L3 cache 3 MB, 4MB, and 6 MB

Table 18. Memory

Feature Specification

Memory connector Two SODIMM slots

Memory capacity 4 GB or 8 GB

Memory type DDR3L SDRAM (1600 MHz)

Minimum memory 4 GB

Maximum memory 16 GB

Table 19. Audio

Feature Specification

Type four-channel high-definition audio

Controller Realtek ALC3226

Stereo conversion 24-bit (analog-to-digital and digital-to-analog)

Interface:

Feature Specification

Internal high-definition audio

External microphone-in, stereo headphones, external speakers

connector

Speakers two

Internal speaker amplifier 1 W (RMS) per channel

Volume controls hot keys

Table 20. Video

Feature Specification

Type integrated on system board

Controller:

UMA AMD professional graphics

Discrete AMD FirePro W4170M

Data bus PCI-E Gen3 x8

External display support • one VGA

• one HDMI

NOTE: Support two DP/DVI ports through Docking

station.

Table 21. Camera

Features Specification

Camera Resolution 1280 x 720 pixels

Video Resolution (maximum) 1280 x 720 pixels

Diagonal viewing angle 74 °

Table 22. Communications

Features Specification

Network adapter 10/100/1000 Mb/s Ethernet (RJ-45)

Wireless internal wireless local area network (WLAN) and wireless

wide area network (WWAN)

Table 23. Ports and Connectors

Features Specification

Audio one microphone/stereo headphone/speakers connector

Video one 15-pin VGA connector and 19-pin HDMI connector

Network adapter one RJ-45 connector

Features Specification

USB Four USB 3.0-compliant connectors

Memory card reader Support upto SD 4.0

Micro Subscriber Identity Module (uSIM)

card

one

Docking port one

Table 24. Contactless Smart Card

Feature Specification

Supported Smart Cards/Technologies BTO with USH

Table 25. Display

Feature Specification

Type FHD Anti-Glare HD Anti-Glare

Dimensions:

Height 224.30 mm (8.83 inches) 224.30 mm (8.83 inches)

Width 360.00 mm (14.17 inches) 360.00 mm (14.17 inches)

Diagonal 396.24 mm (15.60 inches) 396.24 mm (15.60 inches)

Active area (X/Y) 384 mm X 258 mm (15.12 inches X

10.16 inches)

344.23 mm X 193.53 mm (13.55

inches X 7.61 inches)

Maximum resolution 1920 X 1080 1366 X 768

Maximum Brightness 300 nits 200 nits

Refresh rate 60 Hz 60 Hz

Minimum Viewing Angles:

Horizontal +/- 60° 40/40

Vertical +/- 50° 10/30

Pixel pitch 0.179 0.252

Table 26. Keyboard

Feature Specification

Number of keys United States: 86 keys, United Kingdom: 87 keys, Brazil:

87 keys, and Japan: 90 keys

Table 27. Touchpad

Feature Specification

Active Area:

X-axis 80.00 mm

Feature Specification

Y-axis 45.00 mm

Table 28. Battery

Feature Specification

Type 6 cell (65 Whr) lithium ion 9 cell (97 Whr) lithium ion

Dimensions:

Depth 48.08 mm (1.89 inches) 71.79 mm (2.83 inches)

Height 20.00 mm (0.79 inches) 20.00 mm (0.79 inches)

Width 208.00 mm (8.19 inches) 214.00 mm (8.43 inches)

Weight 345.00 g (0.76 lb) 524.00 g (1.16 lb)

Voltage 11.1 VDC

Temperature range:

Operating 0 °C to 50 °C (32 °F to 158 °F)

Non-Operating -20 °C to 65 °C (4 °F to 149 °F)

Coin-cell battery 3 V CR2032 lithium coin cell

Table 29. AC Adapter

Feature Specification

Type 130 W

Input voltage 100 VAC to 240 VAC

Input current (maximum) 2.5 A

Input frequency 50 Hz to 60 Hz

Output current 6.7 A

Rated output voltage 19.5 +/– 1.0 VDC

Temperature range:

Operating 0 °C to 40 °C (32 °F to 104 °F)

Non-Operating –40 °C to 70 °C (–40 °F to 158 °F)

Table 30. Physical

Feature Specification

Height 33.40 mm (1.31 inches)

Width 379.00 mm (14.92 inches)

Depth 250.50 mm (9.86 inches)

Feature Specification

Weight 2.36 kg (5.21 lb)

Table 31. Environmental

Feature Specification

Temperature:

Operating 0 °C to 35 °C (32 °F to 95 °F)

Storage –40 °C to 65 °C (–40 °F to 149 °F)

Relative humidity

(maximum):

Operating 10 % to 90 % (non condensing)

Storage 5 % to 95 % (non condensing)

Altitude (maximum):

Operating –15.2 m to 3048 m (–50 to 10,000 ft)

0° to 35°C

Non-Operating –15.24 m to 10,668 m (–50 ft to 35,000 ft)

Airborne contaminant level G1 as defined by ISA-71.04–1985

Contacting Dell

NOTE: If you do not have an active Internet connection, you can find contact information on your

purchase invoice, packing slip, bill, or Dell product catalog.

Dell provides several online and telephone-based support and service options. Availability varies by

country and product, and some services may not be available in your area. To contact Dell for sales,

technical support, or customer service issues:

1. Visit dell.com/support

2. Select your support category.

3. Verify your country or region in the Choose a Country/Region drop-down menu at the top of page.

4. Select the appropriate service or support link based on your need.

Table of Contents

DELL M2800 User Manual

Related Manuals