Dell Precision 15 7000 series (7510) Owner's Manual
Working on your computer
Removing and installing components
System setup
Diagnostics
- Enhanced Pre-Boot System Assessment (ePSA) diagnostics
Troubleshooting your computer
- Device status lights
- Battery status lights
Specifications
- Technical specification
Contacting Dell

DELL M7510 User Manual

Displayed below is the user manual for M7510 by DELL which is a product in the Notebooks category. This manual has pages.

Related Manuals

DELL M7510 Manual

Dell Precision 15 7000 series (7510)

Owner's Manual

Regulatory Model: P53F

Regulatory Type: P53F001

intellectual property laws. Dell™ and the Dell logo are trademarks of Dell Inc. in the United States and/or other

jurisdictions. All other marks and names mentioned herein may be trademarks of their respective companies.

2015 - 11

Rev. A00

Contents

1 Working on your computer.................................................................................5

Safety instructions................................................................................................................................. 5

Before working inside your computer..................................................................................................6

Recommended tools.............................................................................................................................6

Turning off your computer................................................................................................................... 6

After working inside your computer.....................................................................................................7

2 Removing and installing components..............................................................8

Removing the Secure Digital (SD) card................................................................................................ 8

Installing the SD card............................................................................................................................ 8

Removing the battery cover................................................................................................................. 8

Installing the battery cover................................................................................................................... 9

Removing the battery............................................................................................................................9

Installing the battery..............................................................................................................................9

Removing the base cover..................................................................................................................... 9

Installing the base cover..................................................................................................................... 10

Removing the hard drive.....................................................................................................................10

Installing the hard drive....................................................................................................................... 11

Removing the Subscriber Identification Module (SIM) card...............................................................11

Installing the Subscriber Identification Module (SIM) card................................................................ 12

Removing the keyboard...................................................................................................................... 12

Installing the keyboard........................................................................................................................ 13

Removing the secondary memory..................................................................................................... 14

Installing the secondary memory....................................................................................................... 14

Removing the primary memory..........................................................................................................14

Installing the primary memory............................................................................................................15

Removing Wireless Wide Area Network (WWAN) card (Optional).....................................................15

Installing the WWAN card (Optional)..................................................................................................16

Removing the Wireless Local Area Network (WLAN) card.................................................................16

Installing the WLAN Card.....................................................................................................................17

Removing the M.2 Solid State Drive (SSD)..........................................................................................17

Installing the M.2 SSD..........................................................................................................................18

Removing the coin cell battery...........................................................................................................18

Installing the coin cell battery.............................................................................................................19

Removing the hard drive cable...........................................................................................................19

Installing the hard drive cable............................................................................................................ 20

Removing the power connector port................................................................................................ 20

Installing the power connector port...................................................................................................21

Removing the palmrest....................................................................................................................... 21

Installing the palmrest.........................................................................................................................22

Removing the speakers ......................................................................................................................22

Installing the speakers.........................................................................................................................23

Removing the Input/Output (I/O) board left......................................................................................23

Installing the I/O board left.................................................................................................................24

Removing the Input/Output (I/O) board right................................................................................... 24

Installing the I/O board right.............................................................................................................. 25

Removing the heat sink assembly...................................................................................................... 25

Installing the heat sink assembly........................................................................................................26

Removing the video card....................................................................................................................26

Installing the video card......................................................................................................................27

Removing the display assembly..........................................................................................................27

Installing the display assembly........................................................................................................... 29

Removing the system board...............................................................................................................29

Installing the system board.................................................................................................................30

3 System setup........................................................................................................32

Boot Sequence....................................................................................................................................32

Navigation keys................................................................................................................................... 32

System setup options..........................................................................................................................33

Updating the BIOS ............................................................................................................................. 44

System and setup password...............................................................................................................44

Assigning a system password and setup password..................................................................... 45

Deleting or changing an existing system and/or setup password.............................................. 45

4 Diagnostics.......................................................................................................... 47

Enhanced Pre-Boot System Assessment (ePSA) diagnostics............................................................47

5 Troubleshooting your computer.....................................................................48

Device status lights............................................................................................................................. 48

Battery status lights.............................................................................................................................49

6 Specifications......................................................................................................50

Technical specification.......................................................................................................................50

7 Contacting Dell................................................................................................... 57

Working on your computer

Safety instructions

Use the following safety guidelines to help protect your computer from potential damage and to help to

ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes

that the following conditions exist:

• You have read the safety information that shipped with your computer.

• A component can be replaced or--if purchased separately--installed by performing the removal

procedure in reverse order.

WARNING: Disconnect all power sources before opening the computer cover or panels. After you

finish working inside the computer, replace all covers, panels, and screws before connecting to

the power source.

WARNING: Before working inside your computer, read the safety information that shipped with

your computer. For additional safety best practices information, see the Regulatory Compliance

Homepage at www.dell.com/regulatory_compliance

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or

by periodically touching an unpainted metal surface, such as a connector on the back of the

computer.

CAUTION: Handle components and cards with care. Do not touch the components or contacts

on a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a

processor by its edges, not by its pins.

CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable

itself. Some cables have connectors with locking tabs; if you are disconnecting this type of cable,

press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep

them evenly aligned to avoid bending any connector pins. Also, before you connect a cable,

ensure that both connectors are correctly oriented and aligned.

NOTE: The color of your computer and certain components may appear differently than shown in

this document.

Before working inside your computer

To avoid damaging your computer, perform the following steps before you begin working inside the

computer.

1. Ensure that you follow the Safety instructions.

2. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.

3. Turn off your computer, see Turning off your computer.

CAUTION: To disconnect a network cable, first unplug the cable from your computer and

then unplug the cable from the network device.

4. Disconnect all the network cables from the computer.

5. Disconnect your computer and all attached devices from the electrical outlets.

6. Press and hold the power button while the computer is unplugged to ground the system board.

7. Remove the cover.

CAUTION: Before touching anything inside your computer, ground yourself by touching an

unpainted metal surface, such as the metal at the back of the computer. While you work,

periodically touch an unpainted metal surface to dissipate static electricity, which could

harm internal components.

Recommended tools

The procedures in this document require the following tools:

• Small flat blade screwdriver

• Phillips #0 screwdriver

• Phillips #1 screwdriver

• Small plastic scribe

Turning off your computer

CAUTION: To avoid losing data, save and close all open files and exit all open programs before

you turn off your computer.

1. Turning off your computer:

• In Windows 10 (using a touch enabled device or mouse):

1. Click or tap .

2. Click or tap and then click or touch Shut down.

• In Windows 8 (using a touch enabled device):

1. Swipe in from the right edge of the screen, opening the Charms menu and select Settings.

2. Tap and then tap Shut down

• In Windows 8 (using a mouse):

1. Point to upper-right corner of the screen and click Settings.

2. Click and then click Shut down.

• In Windows 7:

1. Click Start.

2. Click Shut Down.

1. Click Start.

2. Click the arrow in the lower-right corner of the Start menu and then click Log off.

2. Ensure that the computer and all attached devices are turned off. If your computer and attached

devices did not automatically turn off when you shut down your operating system, press and hold

the power button for about 6 seconds to turn them off.

After working inside your computer

After you complete any replacement procedure, ensure you connect any external devices, cards, and

cables before turning on your computer.

CAUTION: To avoid damage to the computer, use only the battery designed for this particular

Dell computer. Do not use batteries designed for other Dell computers.

1. Connect any external devices, such as a port replicator or media base, and replace any cards, such as

an ExpressCard.

2. Connect any telephone or network cables to your computer.

CAUTION: To connect a network cable, first plug the cable into the network device and then

plug it into the computer.

3. Replace the battery.

4. Replace the base cover.

5. Connect your computer and all attached devices to their electrical outlets.

6. Turn on your computer.

Removing and installing components

This section provides detailed information on how to remove or install the components from your

computer.

Removing the Secure Digital (SD) card

1. Follow the procedure in Before working inside your computer.

2. Press in on the SD card to release it from the computer. Slide the SD card out of the computer.

Installing the SD card

1. Push in the SD card into its slot until it clicks into place.

2. Follow the procedure in After working inside your computer

Removing the battery cover

1. Follow the procedure in Before working inside your computer.

2. Perform the following steps as shown in the illustration:

a. Slide the release latch to unlock the battery cover [1].

b. Slide and lift the battery cover to remove it from the computer [2].

Installing the battery cover

1. Slide the battery cover into its slot until it clicks into place.

2. Follow the procedure in After working inside your computer.

Removing the battery

1. Follow the procedure in Before working inside your computer.

2. Remove the battery cover.

3. Perform the following steps as shown in the illustration:

a. Slide the release latch to unlock the battery [1].

b. Lift and remove the battery from the computer [2].

Installing the battery

1. Slide the battery into its slot until it clicks into place.

2. Install the battery cover.

3. Follow the procedure in After working inside your computer

Removing the base cover

1. Follow the procedure in Before working inside your computer.

2. Remove the:

a. battery cover

b. battery

3. Perform the following steps as shown in the illustration:

a. Remove the screws that secure the base cover to the computer [1].

b. Slide and lift the base cover away from the computer [2].

Installing the base cover

1. Slide in the base cover to align with the screw holes correctly on the computer.

2. Tighten the screws to secure the base cover to the computer.

3. Install the:

a. battery

b. battery cover

4. Follow the procedure in After working inside your computer.

Removing the hard drive

1. Follow the procedure in Before working inside your computer.

2. Remove the:

a. battery cover

b. battery

3. Perform the following steps as shown in the illustration:

a. Remove the screws that secure the hard drive to the computer [1].

b. Lift the hard-drive latch to the unlock position [2].

c. Slide and lift the hard drive from the computer [3].

4. Remove the screws that secure the hard drive. Lift the hard drive away from the bracket.

Installing the hard drive

1. Tighten the screws to secure the hard drive to hard-drive bracket.

2. Insert the hard drive into its slot in the computer.

3. Tighten the screws to secure the hard drive to the computer.

4. Install the:

a. battery

b. battery cover

5. Follow the procedure in After working inside your computer

Removing the Subscriber Identification Module (SIM) card

1. Follow the procedure in Before working inside your computer.

2. Remove the:

a. battery cover

b. battery

c. base cover

3. Press the sim card and remove it from the sim card slot.

Installing the Subscriber Identification Module (SIM) card

1. Slide the sim card in its slot until it clicks in place.

2. Install the:

a. base cover

b. battery

c. battery cover

3. Follow the procedure in After working inside your computer.

Removing the keyboard

1. Follow the procedures in Before working inside your computer.

2. Remove the:

a. battery cover

b. battery

c. hard drive

3. Peel the tape to access the cable [1]. Lift the tab and disconnect the keyboard cables from the system

board [2, 3].

4. Perform the following steps as shown in the illustration:

a. Pry the keyboard trim starting from bottom and work along the top edge and remove it away

from the computer [1, 2, 3].

b. Remove the screws that secure the keyboard to the computer [4].

c. Lift the front side and slide the keyboard to remove it away from the computer [5].

Installing the keyboard

1. Press and align the keyboard to its compartment.

2. Tighten the screws to secure the keyboard to the computer.

3. Slide in the keyboard trim from the front and align it to its position on the computer. Ensure that the

keyboard trim clicks into its place

4. Connect the keyboard-data cable to the system board.

NOTE: Ensure that you fold the keyboard-data cable in perfect alignment.

5. Affix the tape on the keyboard data cables.

6. Install the:

a. hard drive

b. battery

c. battery cover

7. Follow the procedure in After working inside your computer.

Removing the secondary memory

1. Follow the procedure in Before working inside your computer.

2. Remove the:

a. battery cover

b. battery

c. hard drive

d. keyboard

3. Perform the following steps as shown in the illustration:

a. Remove the screw that secures the memory shield to the computer [1].

b. Lift and remove the memory shield from the computer [2].

c. Pry the retention clips away from the memory module until it pops up [3].

d. Lift the memory module and remove it from the computer [4].

Installing the secondary memory

1. Insert the secondary memory into the memory socket.

2. Press the clips to secure the memory module to the system board.

3. Place the memory shield in its original position on the computer and tighten the screw to secure it to

the computer.

4. Install the:

a. keyboard

b. hard drive

c. battery

d. battery cover

5. Follow the procedure in After working inside your computer.

Removing the primary memory

1. Follow the procedure in Before working inside your computer.

2. Remove the:

a. battery cover

b. battery

c. base cover

3. Pry the retention clips away from the primary memory until it pops up. Lift the primary memory and

remove it from the computer.

Installing the primary memory

1. Insert the primary memory into the memory socket.

2. Press the clips to secure the primary memory to the system board.

3. Install the:

a. base cover

b. battery

c. battery cover

4. Follow the procedure in After working inside your computer.

Removing Wireless Wide Area Network (WWAN) card

(Optional)

1. Follow the procedure in Before working inside your computer.

2. Remove the:

a. battery cover

b. battery

c. base cover

3. Please perform the following steps to remove the WWAN card:

a. Disconnect and remove the antenna cables connected to the WWAN card [1].

b. Remove the screw that secures the WWAN card to the computer [2].

c. Remove the WWAN card from the computer [3].

Installing the WWAN card (Optional)

1. Slide the WWAN card in the WWAN card slot.

2. Tighten the screw to secure the WWAN card to the computer.

3. Route the antenna cables through the routing channels and connect them to the WWAN card.

4. Install the:

a. base cover

b. battery

c. battery cover

5. Follow the procedure in After working inside your computer

Removing the Wireless Local Area Network (WLAN) card

1. Follow the procedure in Before working inside your computer.

2. Remove the:

a. battery cover

b. battery

c. base cover

3. Please perform the following steps to remove the WLAN card from the computer:

a. Remove the screw that secures the WLAN card to the computer.

b. Remove the shield that secure the antenna cables.

c. Disconnect and un-route the antenna cables connected to the WLAN card and remove the

WLAN card from the computer.

Installing the WLAN Card

1. Insert the WLAN card in its slot in the computer.

2. Route the antenna cables through the routing channel and connect them to the WLAN card.

3. Align the shield and tighten the screw to secure the WLAN card to the computer.

4. Install the:

a. base cover

b. battery

c. battery cover

5. Follow the procedures in After working inside your computer

Removing the M.2 Solid State Drive (SSD)

1. Follow the procedures in Before working inside your computer.

2. Remove the:

a. battery cover

b. battery

c. base cover

3. Perform the following steps as shown in the illustration:

a. Remove the screw that secures the shield to the computer.

b. Remove the shield from the computer.

c. Remove the screw that secures the M.2 SSD to the computer.

d. Remove the M.2 SSD away from the computer.

Installing the M.2 SSD

1. Replace the M.2 SSD in its slot.

2. Tighten the screw to secure the M.2 SSD to the computer.

3. Place the shield on the M.2 SSD.

4. Tighten the screw to secure the shield to the computer.

5. Install the:

a. base cover

b. battery

c. battery cover

6. Follow the procedure in After working inside your computer.

Removing the coin cell battery

1. Follow the procedures in Before working inside your computer.

2. Remove the:

a. battery cover

b. battery

c. base cover

3. Disconnect the coin cell battery cable. Pry the coin-cell battery upward and remove it from the

computer.

Installing the coin cell battery

1. Replace the coin cell battery in its slot in the computer.

2. Connect the coin cell battery cable.

NOTE: Ensure that the coin-cell battery cable does not protrude outside its compartment.

3. Install the:

a. base cover

b. battery

c. battery cover

4. Follow the procedure in After working inside your computer.

Removing the hard drive cable

1. Follow the procedures in Before working inside your computer.

2. Remove the:

a. battery cover

b. battery

c. base cover

d. hard drive

3. Remove the screws that secure the hard drive connector to the system board and remove it from the

computer.

Installing the hard drive cable

1. Connect the hard drive cable to the system board and route the cable through the routing channel.

2. Tighten the screws to secure the hard drive cable connector to the computer.

3. Install the:

a. hard drive

b. base cover

c. battery

d. battery cover

4. Follow the procedure in After working inside your computer.

Removing the power connector port

1. Follow the procedure in Before working inside your computer.

2. Remove the:

a. battery cover

b. battery

c. base cover

3. Perform the following steps as shown in the illustration:

a. Disconnect the power connector cable from the computer [1].

b. Remove the screw to remove the bracket from the computer [2].

c. Remove the bracket from the computer [3].

d. Remove the power connector port from the computer [4].

Installing the power connector port

1. Connect the power-connector cable to the computer and route the cable through the routing

channel.

2. Insert the power-connector port in its slot and place the bracket.

3. Tighten the screw to secure the power-connector port to the computer.

4. Install the:

a. base cover

b. battery

c. battery cover

5. Follow the procedure in After working inside your computer.

Removing the palmrest

1. Follow the procedure in Before working inside your computer.

2. Remove the:

a. battery cover

b. battery

c. base cover

d. hard drive

e. keyboard

3. Perform the following steps as shown in the illustration:

a. Remove the screws (M2xL3) at the bottom of the computer which secure the palmrest to the

computer [1].

b. Lift the tab and disconnect the touch-pad cable and security board cable [2, 3].

c. Disconnect the power-switch cable [4].

d. Remove the screws that secure the palmrest to the computer [5].

e. Release the tabs on the edges of the palmrest and remove the palmrest from the computer [6].

Installing the palmrest

1. Align the palmrest from the rear side on the computer and press on the positions indicated until it

snaps in.

2. Tighten the screws that secure the palmrest to the computer.

3. Connect the following cables:

a. security board

b. power-switch cable

c. touchpad

4. Flip the computer and tighten the screws at the bottom of the computer.

5. Install the:

a. keyboard

b. hard drive

c. base cover

d. battery

e. battery cover

6. Follow the procedure in After working inside your computer.

Removing the speakers

1. Follow the procedure in Before working inside your computer.

2. Remove the:

a. battery cover

b. battery

c. base cover

d. hard drive

e. keyboard

f. palmrest

3. Perform the following steps to remove the speaker:

a. Disconnect the speaker cable from the system board [1].

b. Unroute the speaker cable and remove the cable from the routing tabs.

c. Lift the speakers, along with the speaker cable and remove it away from the computer [2].

Installing the speakers

1. Align the speakers along the slots on the computer.

2. Route the speaker cable through the routing tabs on the computer.

3. Connect the speaker cable to the system board.

4. Install the:

a. palmrest

b. keyboard

c. hard drive

d. base cover

e. battery

f. battery cover

5. Follow the procedure in After working inside your computer.

Removing the Input/Output (I/O) board left

1. Follow the procedure in Before working inside your computer.

2. Remove the:

a. battery cover

b. battery

c. base cover

d. hard drive

e. keyboard

f. palmrest

3. Perform the following steps to remove the I/O board:

a. Remove the screws that secure the I/O board to the computer [1, 3].

b. Remove the bracket of the thunderbolt connector [2].

c. Lift the right edge of the I/O board upwards to disengage the connector and remove it from the

computer [4].

Installing the I/O board left

1. Connect the I/O board connector and slide the I/O board into its slot in the computer.

2. Install the thunderbolt bracket.

3. Tighten the screws to secure the I/O board to the computer.

4. Install the:

a. palmrest

b. keyboard

c. hard drive

d. base cover

e. battery

f. battery cover

5. Follow the procedures in After working inside your computer.

Removing the Input/Output (I/O) board right

1. Follow the procedure in Before working inside your computer.

2. Remove the:

a. SD card

b. battery cover

c. battery

d. base cover

e. hard drive

f. keyboard

g. palmrest

3. Perform the following steps to remove the I/O board:

a. Disconnect the speaker cable from the I/O board [1].

b. Remove the screws that secure the I/O board to the computer [2].

c. Lift the left edge of the I/O board upwards to disengage the connector and remove it from

computer [3].

Installing the I/O board right

1. Connect the I/O board connector and slide the I/O board into its slot in the computer.

2. Tighten the screws to secure the I/O board to the computer.

3. Connect the speaker cable to the I/O board.

4. Install the:

a. palmrest

b. keyboard

c. hard drive

d. base cover

e. battery

f. battery cover

g. SD card

5. Follow the procedure in After working inside your computer.

Removing the heat sink assembly

1. Follow the procedure in Before working inside your computer.

2. Remove the:

a. battery cover

b. battery

c. base cover

d. hard drive

e. keyboard

f. palmrest

3. Perform the following steps as shown in the illustration:

a. Disconnect the heat sink fan cables [1, 2] .

b. Loosen the captive screws that secure the heat sink assembly to the computer.

NOTE: Loosen the screws based on the numbering on the heat sink.

c. Lift up and remove the heat sink assembly away from the computer [3].

d. Peel off the tape on the heat pipe.

Installing the heat sink assembly

1. Replace the heat-sink assembly in its slot.

2. Affix the tape on the heat pipe.

3. Tighten the captive screws to secure the heat-sink assembly to the computer.

NOTE: Tighten the screws based on the order mentioned in the removal procedure.

4. Connect the heat-sink fan cables to the system board.

5. Install the:

a. palmrest

b. keyboard

c. hard drive

d. base cover

e. battery

f. battery cover

6. Follow the procedure in After working inside your computer.

Removing the video card

1. Follow the procedure in Before working inside your computer.

2. Remove the:

a. battery cover

b. battery

c. base cover

d. hard drive

e. keyboard

f. palmrest

g. heat sink

3. Perform the following steps as shown in the illustration:

a. Remove the screws that secure the video card to the computer [1].

b. Remove the video card from the computer [2].

Installing the video card

1. Slide the video card into its original position in the computer.

2. Tighten the screws to secure the video card to the computer.

3. Install the:

a. heat sink

b. palmrest

c. keyboard

d. hard drive

e. base cover

f. battery

g. battery cover

4. Follow the procedure in After working inside your computer.

Removing the display assembly

1. Follow the procedure in Before working inside your computer.

2. Remove the:

a. battery cover

b. battery

c. base cover

d. hard drive

e. keyboard

f. WLAN card

g. WWAN card

h. palmrest

3. Perform the following as shown in the illustration:

a. Remove the screws that secure the display hinge cap to the computer [1].

b. Remove the display hinge cap away from the computer [2].

4. Perform the following steps as shown in the illustration:

a. Flip the computer and remove the cosmetic screws from the bottom and back of the computer

[1].

b. Pull up the antenna cables through the routing hole [2].

5. Perform the following as shown in the illustration:

a. Remove the screw that secures the eDP cable bracket [1].

b. Remove the eDP cable bracket [2].

c. Peel off the tape on the heat pipe and disconnect the eDP cable from the system board [3, 4].

d. Remove the screws that secure the display assembly to the computer and remove it from the

computer [5, 6].

Installing the display assembly

1. Tighten the screws to secure the display assembly in place.

2. Affix the tape on the heat pipe.

3. Connect the eDP cable to the correct connectors on the system board.

4. Insert the wireless antenna cables through the routing hole on the chassis.

5. Tighten the screws at the bottom and back of the computer.

6. Align the display hinge cap and tighten the screws to secure it to the computer.

7. Route and connect the antenna cables to their connectors.

8. Install the:

a. palmrest

b. WWAN card

c. WLAN card

d. keyboard

e. hard drive

f. base cover

g. battery

h. battery cover

9. Follow the procedure in After working inside your computer

Removing the system board

1. Follow the procedure in Before working inside your computer.

2. Remove the:

a. SD card

b. battery cover

c. battery

d. base cover

e. hard drive

f. keyboard

g. HDD cable

h. primary memory

i. WLAN card

j. WWAN card

k. M.2 SSD

l. video card

m. power connector port

n. palmrest

o. I/O board left

p. I/O board right

q. heat sink

3. Perform the following steps as shown in the illustration:

a. Remove the screws that secure the shield to the system board [1].

b. Lift the shield away from the computer [2].

c. Disconnect the eDP cable [3, 4].

d. Lift the tab and disconnect the power-connector cable [5, 6].

e. Remove the screws that secure the system board to the computer [7].

f. Lift and remove the system board away from the computer[8].

Installing the system board

1. Align the system board into its original position on the computer.

2. Tighten the screws to secure the system board to the computer.

3. Connect the following cables:

a. power connector

b. eDP

4. Install the:

a. heat sink

b. I/O board right

c. I/O board left

d. palmrest

e. power-connector port

f. video card

g. M.2 SSD

h. WWAN card

i. WLAN card

j. primary memory

k. HDD cable

l. keyboard

m. hard drive

n. base cover

o. battery

p. battery cover

q. SD card

5. Follow the procedure in After working inside your computer.

System setup

System Setup enables you to manage your computer hardware and specify BIOS level options. From the

System Setup, you can:

• Change the NVRAM settings after you add or remove hardware

• View the system hardware configuration

• Enable or disable integrated devices

• Set performance and power management thresholds

• Manage your computer security

Boot Sequence

Boot Sequence allows you to bypass the System Setup‐defined boot device order and boot directly to a

specific device (for example: optical drive or hard drive). During the Power-on Self Test (POST), when the

Dell logo appears, you can:

• Access System Setup by pressing F2 key

• Bring up the one-time boot menu by pressing F12 key

The one-time boot menu displays the devices that you can boot from including the diagnostic option.

The boot menu options are:

• Removable Drive (if available)

• STXXXX Drive

NOTE: XXX denotes the SATA drive number.

• Optical Drive

• Diagnostics

NOTE: Choosing Diagnostics, will display the ePSA diagnostics screen.

The boot sequence screen also displays the option to access the System Setup screen.

Navigation keys

The following table displays the system setup navigation keys.

NOTE: For most of the System Setup options, changes that you make are recorded but do not take

effect until you restart the system.

Table 1. Navigation keys

Keys Navigation

Up arrow Moves to the previous field.

Down arrow Moves to the next field.

Enter Allows you to select a value in the selected field (if applicable) or follow the link in

the field.

Spacebar Expands or collapses a drop‐down list, if applicable.

Tab Moves to the next focus area.

NOTE: For the standard graphics browser only.

Esc Moves to the previous page till you view the main screen. Pressing Esc in the main

screen displays a message that prompts you to save any unsaved changes and

restarts the system.

F1 Displays the System Setup help file.

System setup options

NOTE: Depending on your computer and its installed devices, the items listed in this section may or

may not appear.

Table 2. General

Option Description

System Information This section lists the primary hardware

features of your computer.

• System Information

• Memory Information

• Processor Information

• Device Information

Battery Information Displays the charge status of the battery.

Boot Sequence Allows you to change the order in which

the computer attempts to find an

operating system. All the below options

are enabled by default.

•UEFI: SAMSUNG SSD SM951 M.2

256GB PCIe NVMe (Default Setting)

You can also choose the Boot List

option. The options are:

• Legacy

•UEFI (Default Setting)

Advanced Boot Options When in UEFI boot mode, the Enable

Legacy Option ROMs option will allow

legacy option ROMs to load. This option

is disabled by default.

Option Description

NOTE: Without this option, only

UEFI option ROMs will load. This

option is required for Legacy boot

mode. This option is not allowed if

Secure Boot is enabled.

• Enable Legacy Option ROMs

Date/Time Allows you to set the date and time.

Table 3. System Configuration

Option Description

Integrated NIC Allows you to configure the integrated

network controller. The options are:

• Enable UEFI Network Stack

• Disabled

• Enabled

•Enabled w/PXE (Default Setting)

Parallel Port Allows you to define and set how the

parallel port on the docking station

operates. You can set the parallel port

to:

• Disabled

•AT (Default Setting)

• PS2

• ECP

Serial Port Identifies and defines the serial port

settings. You can set the serial port to:

• Disabled

•COM1 (Default Setting)

• COM2

• COM3

• COM4

NOTE: The operating system may

allocate resources even if the

setting is disabled.

SATA Operation Allows you to configure the internal

SATA hard-drive controller. The options

are:

• Disabled

• AHCI

•RAID On (Default Setting)

NOTE: SATA is configured to

support RAID mode.

Option Description

Drives Allows you to enable or disable various

drives on board. The options are:

•SATA-0

•SATA-1

•SATA-3

•SATA-4

•M.2 PCIe SSD-0

•M.2 PCIe SSD-1

Default Setting: The highlighted devices

are enabled.

SMART Reporting This field controls if the hard drive errors

for the integrated drives are reported

during system startup. This technology

is part of the SMART (Self Monitoring

Analysis and Reporting Technology)

specification. This option is disabled by

default.

• Enable SMART Reporting

USB/Thunderbolt Configuration Allows you to define the USB

configuration. The options are:

•Enable USB Boot Support

•Enable External USB Port

•Enable Thunderbolt Port

• Enable Thunderbolt Boot Support

•Always Allow Dell Dock

• Enable Thunderbolt (and PCIe

behind TBT) Pre-boot

Default Setting: Highlighted options are

enabled.

USB PowerShare Allows you to configure the behavior of

the USB PowerShare feature. The option

is disabled by default.

• Enable USB PowerShare

Audio This field enables or disables the

integrated audio controller.

•Enable Audio

•Enable Microphone

•Enable Internal Speaker

Default Setting: All the options are

enabled.

Keyboard Illumination This field lets you choose the operating

mode of the keyboard illumination

feature.

Option Description

• Disabled

• Dim

•Bright (Default Setting)

Keyboard Backlight Timeout on AC This feature defines the timeout value

for the keyboard backlight when AC

adapter is plugged into the system.

• 5 seconds (Default settings)

• 10 seconds

• 15 seconds

• 30 seconds

• 1 minute

• 5 minute

• 15 minute

• Never

Keyboard Backlight Timeout on Battery This feature defines the timeout value

for the keyboard backlight when system

is running only on battery power.

• 5 seconds

• 10 seconds (Default settings)

• 15 seconds

• 30 seconds

• 1 minute

• 5 minute

• 15 minute

• Never

Touchscreen This field controls whether the

touchscreen is enabled or disabled. The

option is enabled by default.

Unobtrusive Mode When enabled, pressing Fn+F7 will turn

Off all light and sound emissions in the

system. Press Fn+F7 to resume normal

operation. The option is disabled by

default.

• Enable Unobtrusive Mode

Miscellaneous Devices Allows you enable or disable the various

on board devices. The options are:

•Enable Camera

• SD Card Read Only

•Enable Media Card

• Disable Media Card

Default Setting: The highlighted devices

are enabled.

Table 4. Video

Option Description

LCD Brightness Allows you to set the panel brightness independently for battery and AC

power.

Switchable Graphics This option enables or disables switchable graphics technologies such as

NVIDIA Optimus and AMD Power Express .

NOTE: It should only be enabled for Windows 7/8 32/64-bit or

Ubuntu OS. This feature is not applicable to other OS.

•Enable Switchable Graphics (Default Setting)

• Enable dock Display Port

Table 5. Security

Option Description

Admin Password Allows you to set, change, or delete the administrator (admin)

password.

NOTE: You must set the admin password before you set the

system or hard drive password.

NOTE: Successful password changes take effect immediately.

NOTE: Deleting the admin password automatically deletes the

system password and the hard drive password.

NOTE: Successful password changes take effect immediately.

Default Setting: Not set

System Password Allows you to set, change or delete the system password.

NOTE: Successful password changes take effect immediately.

NOTE: Requires the password be entered when the system is

powered on.

Default Setting: Not set

Strong Password Allows you to enforce the option to always set strong passwords.

Default Setting: Enable Strong Password is not selected.

Password Configuration You can define the length of your password. Admin Password Min = 4,

Admin Password Max = 32

Password Bypass Allows you to enable or disable the permission to bypass the System

and the Internal HDD password, when they are set. The options are:

•Disabled (Default Setting)

• Reboot bypass

Password Change Allows you to enable or disable permissions to set a System password

and a Hard Drive password when the admin password is set.

Default Setting: Allow Non-Admin Password Changes is selected

Option Description

Non-Admin Setup Changes Allows you to determine whether changes to setup option are

permitted when an administrator password is set. This option is disabled

by default.

• Allows Wireless Switch Changes

TPM 1.2 Security This option lets you control whether the Trsuted Platform Module

(TPM) in the system is enabled and visible to the operating system.

When disabled the BIOS will not turn On the TPM During POST. The

TPM will be non-functional and invisible to the operating system. When

enabled, the BIOS will turn On the TPM during POST so that it can be

used by the operating system.

NOTE: Disabling this option does not change any settings you may

have made to the TPM, nor does it delete or change any

information or keys you may have stored there. It simply turns Off

the TPM so that it cannot be used. When you re-enable this option,

the TPM will function exactly as it did before it was disabled. This

option is enabled by default.

NOTE: Changes to this option take effect immediately.

•TPM On

• Clear

• PPI Bypass for Enable Commands

• PPI Bypass for Disable Commands

Computrace(R) Allows you to activate or disable the optional Computrace software The

options are:

•Deactivate (Default Setting)

• Disable

• Activate

NOTE: The Activate and Disable options will permanently activate

or disable the feature and no further changes will be allowed

CPU XD Support Allows you to enable the Execute Disable mode of the processor.

Default Setting: Enable CPU XD Support

OROM Keyboard Access Allows you to set access to enter the Option ROM Configuration

screens using hotkeys during boot process. The options are:

•Enable (Default Setting)

• One Time Enable

• Disable

Admin Setup Lockout Allows you to prevent users from entering Setup when an Administrator

password is set.

Default Setting: Disabled

Table 6. Secure Boot

Option Description

Secure Boot Enable This option enables or disables the

Secure Boot feature.

•Disabled (Default Setting)

• Enabled

Expert Key Management Expert key Management allows the PK,

KEK, db, and dbx security key databases

to be manipulated.

• Expert Key Management

– Enable Custom Mode - Disabled

by default

• Custom Mode Key Management

–PK (Default Setting)

– KEK

– Db

– Dbx

Table 7. Performance

Option Description

Multi Core Support This field specifies whether the process

will have one or all cores enabled. The

performance of some applications will

improve with the additional cores. This

option is enabled by default. Allows you

to enable or disable multi-core support

for the processor. The options are:

•All (Default Setting)

• 1

• 2

• 3

Intel SpeedStep Allows you to enable or disable the Intel

SpeedStep feature.

Default Setting: Enable Intel SpeedStep

C States Control Allows you to enable or disable the

additional processor sleep states. Allows

you to enable or disable the additional

processor sleep states.

Default Setting: C states.

Intel TurboBoost Allows you to enable or disable the Intel

TurboBoost mode of the processor.

Default Setting: Enable Intel

TurboBoost

Option Description

Hyper-Thread Control Allows you to enable or disable the

HyperThreading in the processor.

Default Setting: Enabled

Table 8. Power Management

Option Description

AC Behavior Allows the computer to power-on automatically, when AC adapter is

plugged. The option is disabled.

• Wake on AC

Auto On Time Allows you to set the time at which the computer must turn on

automatically. The options are:

•Disabled (Default Setting)

• Every Day

• Weekdays

• Select Days

USB Wake Support Allows you to enable the USB devices to wake the computer from

standby mode. The option is disabled

• Enable USB Wake Support

Wireless Radio Control Allows you to control the WLAN and WWAN radio. The options are:

• Control WLAN radio

• Control WWAN radio

Default Setting: both the options are disabled.

Wake on LAN/WLAN This option allows the computer to power up from the off state when

triggered by a special LAN signal. Wake-up from the Standby state is

unaffected by this setting and must be enabled in the operating system.

This feature only works when the computer is connected to AC power

supply.

•Disabled - Does not allow the system to power on by special LAN

signals when it receives a wake-up signal from the LAN or wireless

LAN. (Default Setting)

• LAN or WLAN - Allows the system to be powered on by special LAN

signals or WLAN signals.

• LAN Only - Allows the system to be powered on by special LAN

signals.

• WLAN Only - Allows the system to be powered on by special WLAN

signals.

Block Sleep Allows you to block the computer from entering into the sleep state.

This option is disabled by default.

• Block Sleep (S3 State)

Peak Shift Peak Shift can be used to minimize AC consumption during peak power

times of day. For each weekday listed, set a start and end time to run in

Peak Shift mode. During these times the system will run from the battery

Option Description

even if the AC is attached as long as the battery stays above the

threshold specified in the Battery Threshold field. After the end time

specified the system will run from AC if attached but will not charge the

battery. The system will again function normally using AC and recharging

the battery after the Charge Start time is specified. This option is disabled

by default.

• Enable Peak Shift

Advanced Battery Charge

Configuration

This places all batteries in the system in Advanced Battery Charging

Mode to maximize battery health. In Advanced Charging Mode the

system will use standard charging algorithm and other techniques during

non-work hours to maximize battery health. During work hours express

charge is used so that the battery will be charged faster and therefore

ready to use again sooner. For each weekday, specify the time of day in

which the system will be most heavily used. Setting the Work Period to 0

means the system will only be lightly used that day. This option is

disabled by default.

• Enable Advanced Battery Charge Mode

Primary Battery

Configuration

Allows you to define how to use the battery charge, when AC is plugged

in. The options are:

• Adaptive (Default settings)

• Standard

• Express Charge

• Primarily AC use

• Custom - You can set the percentage to which the battery must

charge .

Table 9. POST Behavior

Option Description

Adapter Warnings Allows you to activate the adapter warning messages when certain

power adapters are used.

•Enable Adapter Warnings (Default Setting)

Keypad (Embedded) Allows you to choose one of the two methods to enable keypad that is

embedded in the internal keyboard.

•Fn Key Only (Default Setting)

• By Numlock

Mouse/Touchpad Allows you to define how the computer handles the mouse and

touchpad input. The options are:

• Serial Mouse

• PS2 Mouse

•Touchpad/PS-2 Mouse (Default Setting)

Numlock Enable Specifies if the NumLock function can be enabled when the computer

boots. This option is enabled by default.

• Enable Numlock

Option Description

Fn Key Emulation Allows you to match the <Scroll Lock> key feature of PS-2 keyboard with

the <Fn> key feature in an internal keyboard. The option is enabled by

default.

• Enable Fn Key Emulation

Fn Lock Options This option can enable the hot key combination <fn>+<Esc> toggle the

primary behavior of F1–F12, between their standard and secondary

functions. Fn Lock Modes are:

• Lock Mode Disable/Standard

• Lock Mode Enable/Secondary

MEBx Hotkey This option specifies whether the MEBx Hotkey function should be

enabled when the system boots.

•Enable MEBx Hotkey (Default Setting)

Fastboot This option can speed up the boot process by bypassing some

compatibility steps.

• Minimal – Reduces boot time by skipping certain hardware and

configuration initialization during boot.

•Through – Performs complete hardware and configuration

initialization during boot. (Default Setting)

• Auto – Allows the BIOS to decide configuration initialization

performed during the boot.

Extend BIOS POST Time This option creates an additional pre-boot delay. This allows the user to

see POST status messages.

•0 seconds (Default Setting)

• 5 seconds

• 10 seconds

Table 10. Virtualization Support

Option Description

Virtualization This option specifies whether a Virtual Machine Monitor (VMM) can

utilize the additional hardware capabilities provided by Intel Virtualization

technology.

•Enable Intel Virtualization Technology (Default Setting)

VT for Direct I/O Enables or disables the Virtual Machine Monitor (VMM) from utilizing the

additional hardware capabilities provided by Intel Virtualization

technology for direct I/O.

•Enable Intel VT for Direct I/O (Default Setting)

Trusted Execution This option specifies whether a Measured Virtual Machine Monitor

(MVMM) can utilize the additional hardware capabilities provided by Intel

® Trusted Execution Technology. The TPM Virtualization Technology,

and Virtualization Technology for Direct I/O must be enabled to use this

feature. This option is disabled by default.

• Trusted execution

Table 11. Wireless

Option Description

Wireless Switch Allows you to determine which wireless device can be controlled by the

wireless switch. The options are:

•WWAN

•WLAN

•GPS (on WWAN Module)

•Bluetooth

All options are enabled by default.

Wireless Device Enable Allows you to enable or disable the wireless devices. The options are:

•WWAN/GPS

•WLAN

•Bluetooth

All options are enabled by default.

Table 12. Maintenance

Option Description

Service Tag Displays the service tag of your computer.

Asset Tag Allows you to create a system asset tag if an asset tag is not already set.

This option is not set by default.

BIOS Downgrade This field controls flashing of the system firmware to previous revisions.

• Allow BIOS Downgrade

Data Wipe This field allows users to securely erase data from all the internal storage

devices.

• Wipe on Next Boot

Selecting this operation will securely erase all devices installed in the

system. The following is a list of devices affected by this operation:

• Internal HDD

• Internal SDD

• Internal mSATA

• Internal eMMC

BIOS Recovery This enablesthe user to recover from certain corrupted BIOS conditions

from a recovery file on the user primary hard drive or an external USB

key. This options is enabled by default.

• Enable Recovery from Hard Drive

Table 13. System Logs

Option Description

BIOS events Displays the system event log and allows you to clear the log.

Thermal Events Displays the thermal event logs and allows you clear the thermal event

log.

Power Events Displays the power event logs and allows you clear the power event log.

Updating the BIOS

It is recommended to update your BIOS (system setup), on replacing the system board or if an update is

available. For laptops, ensure that your computer battery is fully charged and connected to a power

outlet.

1. Restart the computer.

2. Go to dell.com/support.

3. If you have your computer's Service Tag or Express Service Code:

NOTE: To locate the Service Tag, click Where is my Service Tag?

NOTE: If you cannot find your Service Tag, click Detect Service Tag. Proceed with the

instructions on screen.

4. Enter the Service Tag or Express Service Code and click Submit.

5. If you are unable to locate or find the Service Tag, click the Product Category of your computer.

6. Choose the Product Type from the list.

7. Select your computer model and the Product Support page of your computer appears.

8. Click Drivers & Downloads.

9. On the Drivers and Downloads screen, under the Operating System drop-down list, select BIOS.

10. Identify the latest BIOS file and click Download File.

11. Select your preferred download method in the Please select your download method below

window; click Download File.

The File Download window appears.

12. Click Save to save the file on your computer.

13. Click Run to install the updated BIOS settings on your computer.

Follow the instructions on the screen.

System and setup password

You can create a system password and a setup password to secure your computer.

Password Type Description

System password Password that you must enter to log on to your system.

Setup password Password that you must enter to access and make changes to the BIOS settings of

your computer.

CAUTION: The password features provide a basic level of security for the data on your computer.

CAUTION: Anyone can access the data stored on your computer if it is not locked and left

unattended.

NOTE: Your computer is shipped with the system and setup password feature disabled.

Assigning a system password and setup password

You can assign a new System Password and/or Setup Password or change an existing System Password

and/or Setup Password only when Password Status is Unlocked. If the Password Status is Locked, you

cannot change the System Password.

NOTE: If the password jumper is disabled, the existing System Password and Setup Password are

deleted and you need not provide the system password to log on to the computer.

To enter a system setup, press <F2> immediately after a power-on or re-boot.

1. In the System BIOS or System Setup screen, select System Security and press Enter.

The System Security screen appears.

2. In the System Security screen, verify that Password Status is Unlocked.

3. Select System Password , enter your system password, and press Enter or Tab.

Use the following guidelines to assign the system password:

• A password can have up to 32 characters.

• The password can contain the numbers 0 through 9.

• Only lower case letters are valid, upper case letters are not allowed.

• Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).

Re-enter the system password when prompted.

4. Type the system password that you entered earlier and click OK.

5. Select Setup Password, type your system password and press Enter or Tab.

A message prompts you to re-type the setup password.

6. Type the setup password that you entered earlier and click OK.

7. Press Esc and a message prompts you to save the changes.

8. Press Y to save the changes.

The computer reboots.

Deleting or changing an existing system and/or setup password

Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or change

the existing System and/or Setup password. You cannot delete or change an existing System or Setup

password, if the Password Status is Locked.

To enter the System Setup, press F2 immediately after a power-on or reboot.

1. In the System BIOS or System Setup screen, select System Security and press Enter.

The System Security screen is displayed.

2. In the System Security screen, verify that Password Status is Unlocked.

3. Select System Password, alter or delete the existing system password and press Enter or Tab.

4. Select Setup Password, alter or delete the existing setup password and press Enter or Tab.

NOTE: If you change the System and/or Setup password, re-enter the new password when

promoted. If you delete the System and/or Setup password, confirm the deletion when

promoted.

5. Press Esc and a message prompts you to save the changes.

6. Press Y to save the changes and exit from System Setup.

The computer reboots.

Diagnostics

If you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for

technical assistance. The purpose of running diagnostics is to test your computer's hardware without

requiring additional equipment or risking data loss. If you are unable to fix the problem yourself, service

and support personnel can use the diagnostics results to help you solve the problem.

Enhanced Pre-Boot System Assessment (ePSA)

diagnostics

The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware.

The ePSA is embedded with the BIOS and is launched by the BIOS internally. The embedded system

diagnostics provides a set of options for particular devices or device groups allowing you to:

• Run tests automatically or in an interactive mode

• Repeat tests

• Display or save test results

• Run thorough tests to introduce additional test options to provide extra information about the failed

device(s)

• View status messages that inform you if tests are completed successfully

• View error messages that inform you of problems encountered during testing

CAUTION: Use the system diagnostics to test only your computer. Using this program with other

computers may cause invalid results or error messages.

NOTE: Some tests for specific devices require user interaction. Always ensure that you are present

at the computer terminal when the diagnostic tests are performed.

1. Power-on the computer.

2. As the computer boots, press the F12 key as the Dell logo appears.

3. On the boot menu screen, select the Diagnostics option.

The Enhanced Pre-boot System Assessment window is displayed, listing all devices detected in the

computer. The diagnostics starts running the tests on all the detected devices.

4. To run a diagnostic test on a specific device, press Esc and click Yes to stop the diagnostic test.

5. Select the device from the left pane and click Run Tests.

6. If there are any issues, error codes are displayed.

Note the error code and contact Dell.

Troubleshooting your computer

You can troubleshoot your computer using indicators like diagnostic lights, beep codes, and error

messages during the operation of the computer.

Device status lights

Table 14. Device status lights

Turns on when you turn on the computer and blinks when the computer is in a power

management mode.

Turns on when the computer reads or writes data.

Turns on steadily or blinks to indicate battery charge status.

Turns on when wireless networking is enabled.

The device status LEDs are usually located either on the top or left side of the keyboard. They are used to

display the storage, battery and wireless devices connectivity and activity. Apart from that they can be

useful as a diagnostic tool when there's a possible failure to the system.

The following table lists how to read the LED codes when possible errors occur.

Table 15. LED lights

Storage LED Power LED Wireless LED Fault Description

Blinking Solid Solid A possible processor failure has occurred.

Solid Blinking Solid The memory modules are detected but has

encountered an error.

Blinking Blinking Blinking A system board failure has occurred.

Blinking Blinking Solid A possible graphics card/video failure has occurred.

Blinking Blinking Off System failed on hard drive initialization OR System

failed in Option ROM initialization.

Blinking Off Blinking The USB controller encountered a problem during

initialization.

Solid Blinking Blinking No memory modules are installed/detected.

Blinking Solid Blinking The display encountered a problem during

initialization.

Storage LED Power LED Wireless LED Fault Description

Off Blinking Blinking The modem is preventing the system from completing

POST.

Off Blinking Off Memory failed to initialize or memory is unsupported.

Battery status lights

If the computer is connected to an electrical outlet, the battery light operates as follows:

Alternately blinking

amber light and

white light

An unauthenticated or unsupported non-Dell AC adapter is attached to your

laptop.

Alternately blinking

amber light with

steady white light

Temporary battery failure with AC adapter present.

Constantly blinking

amber light

Fatal battery failure with AC adapter present.

Light off Battery in full charge mode with AC adapter present.

White light on Battery in charge mode with AC adapter present.

Specifications

Technical specification

NOTE: Offerings may vary by region. For more information regarding the configuration of your

computer in:

• Windows 10, click or tap Start → Settings → System → About.

• Windows 8.1 and Windows 8, click or tap Start → PC Settings → PC and devices → PC

Info.

• Windows 7, click Start , right-click My Computer, and then select Properties.

Table 16. System Information

Feature Specification

System Chipset Intel SKL PCH-H CM236

Interrupt Levels Interrupt Controller

• Supports up to eight legacy interrupt pins

• Supports PCI 2.3 Message Signaled

Interrupts

• Integrated IO APIC capability with 24 interrupts

• Supports Processor System Bus interrupt delivery

BIOS Chip (NVRAM) 128 Mb (16 MB)

Table 17. Processor

Feature Specification

Processor type • Intel Core i5 and i7 Quad Core (6th generation)

• Intel Xeon

L1 cache Up to 32 KB cache depending on processor type

L2 cache Up to 256 KB cache depending on processor type

L3 cache Up to 8 MB cache depending on processor type

Feature Specification

Intel Smart cache with Last Level

Cache

Up to 8 MB cache depending on processor type

Table 18. Memory

Feature Specification

Type DDR4

Speed 2133MHz, 2667MHz and ECC 2133MHz

Connectors 4 SoDIMM Sockets

Capacity 4 GB, 8 GB, and 16 GB

Minimum Memory 8 GB

Maximum memory 64 GB

Table 19. Video

Feature Specification

Type MXM type-A add-in card

Data bus PCIE x16, Gen3

Video controller and memory: • AMD FirePro W5170M, 2GB GDDR5

• Nvidia Quadro M1000M, 2GB GDDR5

• Nvidia Quadro M2000M, 4GB GDDR5

Table 20. Audio

Feature Specification

Integrated dual-channel High-Definition audio

Table 21. Communication

Feature Specification

Network adapter network interface card capable of 10/100/1000 Mb/s

communication

Wireless • internal wireless local area network (WLAN)

• internal wireless wide area network (WWAN)

• bluetooth wireless support

• High speed bluetooth 4.0

Table 22. Expansion Bus

Feature Specification

Bus Type PCI Express 1.0, 2.0 and 3.0, SATA 1.0A ,2.0 and 3.0, USB 2.0

and 3.0

Bus Width PCIe X16

BIOS Chip (NVRAM) 128 Mb (16 MB)

Table 23. Ports and Connectors

Feature Specification

Audio Universal audio jack connector

Network Adapter one RJ45 connector

USB C connector one (optional)

USB 3.0 four

Video 19-pin HDMI connector, Mini DisplayPort connector

Memory card reader SD 4.0

Docking port one

Micro Subscriber Identity Module

(Micro SIM) port

one

Smart card (optional) one

Table 24. Display

Feature

Type • FHD (1920 x 1080)

• UHD (3840 x 2160)

Size 15.6 inches

Dimensions:

Height 210 mm (8.26 inches)

Width 359.80 mm (14.16 inches)

Diagonal 396.24 mm (15.60 inches)

Active area (X/Y) • FHD (1920 x 1080)

• UHD (3840 x 2160)

Maximum resolution • FHD (1920 x 1080)

• UHD (3840 x 2160)

Maximum Brightness • UHD (400 nits)

Operating angle 0° (closed) to 135°

Feature

Refresh rate 60 Hz

Minimum viewing angles:

Horizontal/Vertical • FHD (60/60/50/50)

Table 25. Keyboard

Feature Specification

Number of keys • United States: 103 keys

• United Kingdom: 104 keys

• Brazil: 106 keys

• Japan: 107 keys

Layout QWERTY/AZERTY/Kanji

Table 26. Touchpad

Feature Specification

Active Area:

X-axis 99.5 mm

Y-axis 53 mm

Table 27. Camera

Feature Specification

Type CMOS Sensor

Still Resolution 1280 x 720 Pixels ( Maximum )

Video Resolution 1280 x 720 Pixels @ 30 Frame Per Seconds ( Maximum )

Diagonal 74 degrees

Table 28. Storage

Feature Specification

Storage:

Storage Interface • SATA 1 (1.5 Gb/s)

• SATA 2 (3.0 Gb/s)

• SATA 3 (6 Gb/s)

• PCIe express

Drives configuration one internal 9.5/7.0/5.0/ mm SATA HDD/SSD (SATA3)

Size 1 TB 5400 rpm, 128/256/512 GB SATA 3 SSD, 256 GB SATA 3 SSD,

1 TB M.2 SSD, 1 TB SATA 3 SSD

Feature Specification

NOTE: The size of the hard drive is bound to change. For

more information, see dell.com.

Table 29. Battery

Feature Specification

Type lithium ion

Dimensions (6-cell entry/ 6-cell upsell/ 6-cell long cycle life (LCL)):

Depth 71.3 mm (2.81 inches)

Height 234.89 mm (9.25 inches)

Width 18.45 mm (0.73 inches)

Weight • 6-cell entry - 395 g (0.87 lb)

• 6-cell upsell/ LCL- 405 g (0.89 lb)

Voltage • 6-cell entry — 11.1 V

• 6-cell upsell/ LCL — 11.4 V

Life span • 300 discharge/charge cycles

• 1000 discharge/charge cycles (LCL)

Temperature range:

Operating • Charge : 0 °C to 50 °C (32 °F to 158 °F)

• Discharge: 0 °C to 70 °C (32 °F to 122 °F)

Non-operating -20 °C to 65 °C (4 °F to 149 °F)

Coin-cell battery 3 V CR2032 lithium ion cell

Table 30. AC Adapter

Feature Specification

Input voltage 100 VAC to 240 VAC

Input current (maximum) 2.34 A

Input frequency 50 Hz to 60 Hz

Output power 180 W

Output current 9.23 A

Rated output voltage 19.50 VDC

Dimensions: 180 W

Height 30 mm (1.18 inches)

Width 155 mm (6.10 inches)

Depth 76.2 mm (3.0 inches)

Feature Specification

Weight 0.58 kg (1.28 lb)

Temperature range:

Operating 0 °C to 40 °C (32 °F to 104 °F)

Non Operating –40 °C to 70°C (–40 °F to 158 °F)

Table 31. Contactless Smart Card

Feature Specification

Supported Smart Cards and

Technologies

• ISO14443A — 160 kbps, 212 kbps, 424 kbps, and 848 kbps

• ISO14443B — 160 kbps, 212 kbps, 424 kbps, and 848 kbps

• ISO15693

• HID iClass

• FIPS201

• NXP Desfire

Table 32. Physical Dimension

Physical Specification

Height:

Touch • Front: 28.4 mm (1.12 inches)

• Back: 33.7 mm (1.33 inches)

Non-touch • Front: 27.7 mm (1.09 inches)

• Back: 33.0 mm ( 1.30 inches)

Width 378 mm (14.88 inches)

Depth 261 mm (10.28 inches)

Weight (Minimum) 2.80 kg (6.17 lb)

Table 33. Environmental

Feature Specification

Temperature range:

Operating 0 °C to 40°C (32 °F to 104°F)

Storage –40 °C to 65 °C (–40 °F to 149 °F)

Relative humidity (maximum):

Operating 10 % to 90 % (non-condensing)

Storage 5 % to 95 % (non-condensing)

Maximum vibration:

Operating 0.66 GRMS, 2 Hz - 600 Hz

Storage 1.3 GRMS, 2 Hz - 600 Hz

Feature Specification

Maximum shock:

Operating 140 G, 2 ms

Non-operating 163 G, 2 ms

Altitude:

Storage 0 m to 10668 m (0 ft to 35,000 ft)

Airborne contaminant level G1 or lower as defined by ANSI/ISA-S71.04-1985

Contacting Dell

NOTE: If you do not have an active Internet connection, you can find contact information on your

purchase invoice, packing slip, bill, or Dell product catalog.

Dell provides several online and telephone-based support and service options. Availability varies by

country and product, and some services may not be available in your area. To contact Dell for sales,

technical support, or customer service issues:

1. Go to Dell.com/support.

2. Select your support category.

3. Verify your country or region in the Choose a Country/Region drop-down list at the bottom of the

page.

4. Select the appropriate service or support link based on your need.

Table of Contents

DELL M7510 User Manual

Related Manuals