Table of Contents
- Dell Precision 7720 Owner's Manual
- Working on your computer
- Removing and installing components
- Technology and components
- Technical specifications
- System setup
- Troubleshooting
- Contacting Dell
DELL M7720 User Manual
Displayed below is the user manual for M7720 by DELL which is a product in the Notebooks category. This manual has pages.
Related Manuals
Dell Precision 7720
Owner's Manual
Regulatory Model: P29E
Regulatory Type: P29E002
Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use of your product.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
© 2017 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks
may be trademarks of their respective owners.
2017 - 03
Rev. A00
Contents
1 Working on your computer............................................................................................................................. 6
Safety instructions............................................................................................................................................................. 6
Before working inside your computer..............................................................................................................................6
Turning o your computer — Windows 10.....................................................................................................................7
After working inside your computer.................................................................................................................................7
2 Removing and installing components............................................................................................................. 8
Recommended tools.......................................................................................................................................................... 8
Battery cover......................................................................................................................................................................8
Removing the battery cover....................................................................................................................................... 8
Installing the battery cover......................................................................................................................................... 8
Battery.................................................................................................................................................................................9
Removing the battery..................................................................................................................................................9
Installing the battery.................................................................................................................................................... 9
Hard drive............................................................................................................................................................................9
Removing the hard drive............................................................................................................................................. 9
Installing the hard drive..............................................................................................................................................10
Keyboard.............................................................................................................................................................................11
Removing the keyboard.............................................................................................................................................. 11
Installing the keyboard................................................................................................................................................12
Base cover.........................................................................................................................................................................12
Removing the base cover.......................................................................................................................................... 12
Installing the base cover............................................................................................................................................ 13
Memory module................................................................................................................................................................ 13
Removing the primary memory module...................................................................................................................13
Installing the primary memory module..................................................................................................................... 14
Removing the secondary memory module..............................................................................................................14
Installing the secondary memory module................................................................................................................ 15
WWAN card.......................................................................................................................................................................15
Removing Wireless Wide Area Network (WWAN) card........................................................................................ 15
Installing the WWAN card .........................................................................................................................................16
WLAN card........................................................................................................................................................................16
Removing the Wireless Local Area Network (WLAN) card...................................................................................16
Installing the WLAN Card...........................................................................................................................................17
Coin cell battery................................................................................................................................................................ 17
Removing the coin cell battery..................................................................................................................................17
Installing the coin cell battery....................................................................................................................................18
3 Technology and components........................................................................................................................ 19
Power adapter...................................................................................................................................................................19
Processors......................................................................................................................................................................... 19
Kaby Lake — 7th Generation Intel Core processors............................................................................................. 20
Identifying processors in Windows 10..................................................................................................................... 20
Contents 3
Verifying processor usage in task manager............................................................................................................ 20
Verifying processor usage in resource monitor....................................................................................................... 21
Chipset.............................................................................................................................................................................. 22
Identifying chipset in device manager on Windows 10..........................................................................................22
Memory features..............................................................................................................................................................23
Verifying system memory in setup.................................................................................................................................23
Verifying system memory ...............................................................................................................................................23
Windows 10.................................................................................................................................................................23
Testing memory using ePSA........................................................................................................................................... 23
Display................................................................................................................................................................................24
Display options............................................................................................................................................................24
Identifying display adapter........................................................................................................................................ 24
Changing the screen resolution................................................................................................................................24
Connecting to external display devices...................................................................................................................25
Camera features...............................................................................................................................................................25
Identifying the camera in Device Manager on Windows 10..................................................................................25
Starting the camera...................................................................................................................................................25
Starting the camera application............................................................................................................................... 25
Hard drive..........................................................................................................................................................................26
Storage options.......................................................................................................................................................... 26
Identifying the storage device in the BIOS............................................................................................................. 26
Identifying storage device in Windows 10............................................................................................................... 27
USB features.....................................................................................................................................................................27
USB 3.0/USB 3.1 Gen 1 (SuperSpeed USB)........................................................................................................... 27
Speed...........................................................................................................................................................................27
Applications.................................................................................................................................................................28
Compatibility...............................................................................................................................................................29
HDMI 1.4............................................................................................................................................................................29
HDMI 1.4 Features......................................................................................................................................................29
Advantages of HDMI................................................................................................................................................. 29
4 Technical specications................................................................................................................................31
System information...........................................................................................................................................................31
Processor.......................................................................................................................................................................... 32
Memory............................................................................................................................................................................. 32
Video..................................................................................................................................................................................32
Audio..................................................................................................................................................................................32
Communication................................................................................................................................................................ 33
Expansion bus...................................................................................................................................................................33
Ports and connectors...................................................................................................................................................... 33
Display............................................................................................................................................................................... 34
Keyboard........................................................................................................................................................................... 34
Touchpad...........................................................................................................................................................................35
Camera..............................................................................................................................................................................35
Storage..............................................................................................................................................................................35
Battery...............................................................................................................................................................................35
AC adpter..........................................................................................................................................................................36
4Contents
Contactless smart card................................................................................................................................................... 36
Physical dimension........................................................................................................................................................... 37
Environmental................................................................................................................................................................... 37
5 System setup...............................................................................................................................................38
Boot menu........................................................................................................................................................................ 38
Navigation keys................................................................................................................................................................ 39
System setup options......................................................................................................................................................39
General screen options..............................................................................................................................................39
System Conguration screen options..................................................................................................................... 40
Video screen options................................................................................................................................................. 42
Security screen options.............................................................................................................................................43
Secure Boot screen options......................................................................................................................................44
Intel Software Guard Extensions screen options................................................................................................... 45
Performance screen options.................................................................................................................................... 45
Power Management screen options........................................................................................................................46
POST Behavior screen options.................................................................................................................................47
Manageability screen options................................................................................................................................... 48
Virtualization support screen options............................................................................................................................49
Wireless screen options...................................................................................................................................................49
Maintenance screen options...........................................................................................................................................49
System Log screen options............................................................................................................................................ 50
Updating the BIOS ......................................................................................................................................................... 50
System and setup password........................................................................................................................................... 51
Assigning a system password and setup password................................................................................................51
Deleting or changing an existing system and/or setup password........................................................................ 51
6 Troubleshooting........................................................................................................................................... 53
Enhanced Pre-Boot System Assessment (ePSA) diagnostics...................................................................................53
Running the ePSA diagnostics.................................................................................................................................53
Device status lights..........................................................................................................................................................53
Battery status lights.........................................................................................................................................................54
Real Time Clock (RTC) reset..........................................................................................................................................54
7 Contacting Dell............................................................................................................................................ 56
Contents 5
Working on your computer
Safety instructions
Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless otherwise
noted, each procedure included in this document assumes that the following conditions exist:
• You have read the safety information that shipped with your computer.
• A component can be replaced or, if purchased separately, installed by performing the removal procedure in reverse order.
WARNING: Disconnect all power sources before opening the computer cover or panels. After you nish working inside the
computer, replace all covers, panels, and screws before connecting to the power source.
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional
safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance
CAUTION: Many repairs may only be done by a certied service technician. You should only perform troubleshooting and simple
repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage
due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came
with the product.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an
unpainted metal surface, such as a connector on the back of the computer.
CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its
edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by its pins.
CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some cables have
connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the
cable. As you pull connectors apart, keep them evenly aligned to avoid bending any connector pins. Also, before you connect a
cable, ensure that both connectors are correctly oriented and aligned.
NOTE: The color of your computer and certain components may appear dierently than shown in this document.
Before working inside your computer
1 Ensure that your work surface is at and clean to prevent the computer cover from being scratched.
2 Turn o your computer.
3 If the computer is connected to a docking device (docked), undock it.
4 Disconnect all network cables from the computer (if available).
CAUTION: If your computer has an RJ45 port, disconnect the network cable by rst unplugging the cable from your
computer.
5 Disconnect your computer and all attached devices from their electrical outlets.
6 Close the display and turn the computer upside-down on a at work surface.
NOTE: To avoid damaging the system board, you must remove the main battery before you service the computer.
7 Remove the base cover.
8 Remove the main battery.
9 Turn the computer top-side up.
10 Open the display.
1
6 Working on your computer
11 Press and hold the power button for few seconds, to ground the system board.
CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before opening the
display.
CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface,
such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to
dissipate static electricity, which could harm internal components.
12 Remove any installed ExpressCards or Smart Cards from the appropriate slots.
Turning o your computer — Windows 10
CAUTION: To avoid losing data, save and close all open les and exit all open programs before you turn o your
computer.
1 Click or tap .
2 Click or tap and then click or tap Shut down.
NOTE: Ensure that the computer and all attached devices are turned o. If your computer and attached devices did not
automatically turn o when you shut down your operating system, press and hold the power button for about 6 seconds
to turn them o.
After working inside your computer
After you complete any replacement procedure, ensure that you connect external devices, cards, and cables before turning on your
computer.
CAUTION: To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not use batteries
designed for other Dell computers.
1 Connect any external devices, such as a port replicator or media base, and replace any cards, such as an ExpressCard.
2 Connect any telephone or network cables to your computer.
CAUTION: To connect a network cable, rst plug the cable into the network device and then plug it into the
computer.
3 Replace the battery.
4 Connect your computer and all attached devices to their electrical outlets.
5 Turn on your computer.
Working on your computer 7
Removing and installing components
This section provides detailed information on how to remove or install the components from your computer.
Recommended tools
The procedures in this document require the following tools:
• Phillips #0 screwdriver
• Phillips #1 screwdriver
• Plastic scribe
Battery cover
Removing the battery cover
1 Follow the procedure in Before working inside your computer.
2 To remove the battery cover:
a Slide the release latch towards the unlock icon to release the battery cover [1].
b Slide and lift the battery cover to remove it from the computer [2].
Installing the battery cover
1 Slide the battery cover into its slot until it clicks into place.
2 Follow the procedure in After working inside your computer.
2
8 Removing and installing components
Battery
Removing the battery
1 Follow the procedure in Before working inside your computer.
2 Remove the battery cover.
3 To remove battery:
a Slide the release latch towards from the unlock icon to unlock the battery[1].
b Lift and remove the battery from the computer [2].
Installing the battery
1 Slide the battery into its slot until it clicks into place.
2 Install the battery cover.
3 Follow the procedure in After working inside your computer
Hard drive
Removing the hard drive
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abattery cover
bbattery
3 To remove hard drive:
a Remove the M3.0x3.0 screws that secure the hard drive to the computer [1].
b Lift the hard drive latch to release the hard drive [2].
c Slide and lift the hard drive from the computer [3].
Removing and installing components 9
4 Remove the M3.0x3.0 screws that secure the hard drive. Lift the hard drive from the bracket.
Installing the hard drive
1 Replace the M3.0x3.0 screws to secure the hard drive to the hard drive bracket.
2 Insert the hard drive into its slot in the computer.
3 Replace the M3.0x3.0 screws to secure the hard drive to the computer.
4 Install the:
abattery
bbattery cover
5 Follow the procedure in After working inside your computer.
10 Removing and installing components
Keyboard
Removing the keyboard
1 Follow the procedures in Before working inside your computer.
2 Remove the:
abattery cover
bbattery
chard drive
3 To remove keyboard cable:
a Disconnect the keyboard cables from the system board [1, 2]
4 Using plastic scribe pry the keyboard trim from the bottom and work along the top edge and remove it from the computer [1, 2, 3, 4].
5 To remove the keyboard:
a Remove the M2.0x2.5 screws that secure the keyboard to the computer [1].
Removing and installing components 11
b Lift and slide the keyboard to remove it away from the computer [2, 3].
Installing the keyboard
1 Press and align the keyboard to its compartment.
2 Replace the screws to secure the keyboard to the computer.
3 Slide the keyboard trim and align it to its position on the computer. Ensure that the keyboard trim clicks into its place
4 Connect the keyboard data cables to the system board.
NOTE: Ensure that you fold the keyboard data cable in perfect alignment.
5 Install the:
ahard drive
bbattery
cbattery cover
6 Follow the procedure in After working inside your computer.
Base cover
Removing the base cover
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abattery cover
bbattery
3 To remove base cover:
a Remove the M2.5X5.0 screws that secure the base cover to the computer [1].
b Slide and lift the base cover away from the computer [2].
12 Removing and installing components
Installing the base cover
1 Slide the base cover to align with the screw holes on the computer.
2 Replace the M2.5X5.0 screws to secure the base cover to the computer.
3 Install the:
abattery
bbattery cover
4 Follow the procedure in After working inside your computer.
Memory module
Removing the primary memory module
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abattery cover
bbattery
cbase cover
3 To remove primary memory module:
a Pry the retention clips away from the memory module until it pops up.
b Lift the memory module and remove it from the computer.
Removing and installing components 13
Installing the primary memory module
1 Insert the memory module into the memory socket.
NOTE: Install either two or four memory modules in the memory module slots to ensure optimum system performance.
Installing one or three memory modules lead to system performance issues.
2 Press the clips to secure the memory module to the system board.
3 Install the:
abase cover
bbattery
cbattery cover
4 Follow the procedure in After working inside your computer.
Removing the secondary memory module
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abattery cover
bbattery
chard drive
dkeyboard
3 To remove the secondary memory module:
a Remove the screw that secures the memory shield [1].
b Lift and remove the memory shield from the computer [2].
c Pry the retention clips away from the memory module until it pops up [3].
d Lift the memory module and remove it from the computer [4].
14 Removing and installing components
Installing the secondary memory module
1 Insert the memory module into the memory socket.
2 Press the clips to secure the memory module to the system board.
3 Place the memory shield in its original position on the memory module and tighten the screw to secure it to the computer.
4 Install the:
akeyboard
bhard drive
cbattery
dbattery cover
5 Follow the procedure in After working inside your computer.
WWAN card
Removing Wireless Wide Area Network (WWAN) card
NOTE: Depending on the conguration you choose, you may or may not have WWAN
card.
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abattery cover
bbattery
cbase cover
3 To remove the WWAN card:
a Disconnect and unroute the antenna cables connected to the WWAN card [1].
b Remove the M2.0x3.0 screw that secures the WWAN card to the computer [2].
c Remove the WWAN card from the computer [3].
Removing and installing components 15
Installing the WWAN card
NOTE: Depending on the conguration you choose, you may or may not have WWAN
card.
1 Slide the WWAN card to the WWAN card slot.
2 Replace the M2.0x3.0 screw to secure the WWAN card to the computer.
3 Route the antenna cables through the routing channels and connect them to the WWAN card.
4 Install the:
abase cover
bbattery
cbattery cover
5 Follow the procedure in After working inside your computer.
WLAN card
Removing the Wireless Local Area Network (WLAN) card
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abattery cover
bbattery
cbase cover
3 To remove the WLAN card from the computer:
a Remove the M2.0x3.0 screw that secures the WLAN card to the computer [1].
b Remove the shield that secures the antenna cables [2].
c Disconnect and un-route the antenna cables connected to the WLAN card and remove the WLAN card from the computer [3,4].
16 Removing and installing components
Installing the WLAN Card
1 Insert the WLAN card in its slot on the computer.
2 Route the antenna cables through the routing channel and connect them to the WLAN card.
3 Align the shield and tighten the M2.0x3.0 screw to secure the WLAN card to the computer.
4 Install the:
abase cover
bbattery
cbattery cover
5 Follow the procedures in After working inside your computer.
Coin cell battery
Removing the coin cell battery
1 Follow the procedures in Before working inside your computer.
2 Remove the:
abattery cover
bbattery
cbase cover
3 To remove coin cell battery:
a Disconnect the coin cell battery cable from the computer [1].
b Pry and lift the coin cell battery from the computer [2].
Removing and installing components 17
Installing the coin cell battery
1 Replace the coin cell battery in its slot on the computer.
2 Connect the coin cell battery cable to the comupter.
NOTE: Ensure that the coin cell battery cable does not protrude outside its compartment.
3 Install the:
abase cover
bbattery
cbattery cover
4 Follow the procedure in After working inside your computer.
18 Removing and installing components
Technology and components
This chapter details the technology and components available in the systems.
Topics:
• Power adapter
• Processors
• Chipset
• Memory features
• Verifying system memory in setup
• Verifying system memory
• Testing memory using ePSA
• Display
• Camera features
• Hard drive
• USB features
• HDMI 1.4
Power adapter
This laptop is shipped with 240 W power adapters.
WARNING: When you disconnect the power adapter cable from the laptop, grasp the connector, not the cable itself, and then
pull rmly but gently to avoid damaging the cable.
WARNING: The power adapter works with electrical outlets worldwide. However, power connectors and power strips vary among
countries. Using an incompatible cable or improperly connecting the cable to the power strip or electrical outlet may cause re or
equipment damage.
Processors
Latitude 7720 is shipped with any of the following processors:
7th generation processors (KabyLake)
• Intel Core Xeon E3-1535M v6 (Quad Core Xeon 3.10GHz, 4.20GHz Turbo, 8MB 45W)
• Intel Core Xeon E3-1505M v6 (Quad Core Xeon 3.00GHz, 4.00GHz Turbo, 8MB 45W)
• Intel Core i7-7920HQ (Quad Core 3.10GHz, 4.10GHz Turbo, 8MB 45W)
• Intel Core i7-7820HQ (Quad Core 2.90GHz, 3.90GHz Turbo, 8MB 45W)
• Intel Core i7-7700HQ (Quad Core 2.80GHz, 3.80GHz Turbo, 6MB 45W)- non vPro
• Intel Core i5-7440HQ (Quad Core 2.80GHz, 3.80GHz Turbo, 6MB 45W)
• Intel Core i5-7300HQ (Quad Core 2.50GHz, 3.50GHz Turbo, 6MB 45W)
6th generation processors (SkyLake)
• Intel Core Xeon E3-1575M v5 (Quad Core Xeon 3.00GHz, 3.90GHz Turbo, 8MB 45W)
• Intel Core Xeon E3-1545M v5 (Quad Core Xeon 2.90GHz, 3.80GHz Turbo, 8MB 45W)
3
Technology and components 19
• Intel Core i7-6920HQ (Quad Core 2.90GHz, 3.80GHz Turbo, 8MB 45W)
• Intel Core i7-6820HQ (Quad Core 2.70GHz, 3.60GHz Turbo, 8MB 45W)
NOTE: The clock speed and performance varies depending on the workload and other variables.
Kaby Lake — 7th Generation Intel Core processors
The 7th Gen Intel Core processor (Kaby Lake) family is the successor of 6th generation processors (Skylake). It's main features include:
• Intel 14nm Manufacturing Process Technology
• Intel Turbo Boost Technology
• Intel Hyper Threading Technology
• Intel Built-in Visuals
• Intel HD graphics - exceptional videos, editing smallest details in the videos
• Intel Quick Sync Video - excellent video conferencing capability, quick video editing and authoring
• Intel Clear Video HD - visual quality and color delity enhancements for HD playback and immersing web browsing
• Integrated memory controller
• Intel Smart Cache
• Optional Intel vPro technology (on i5/i7) with Active Management Technology 11.6
• Intel Rapid Storage Technology
NOTE: Windows 7 and 8 are not supported by systems with 7th generation processors
Identifying processors in Windows 10
1 Type Device Manager in Ask me anything eld.
The iDevice Manager window is displayed.
2 Click Processor.
The processor information is displayed.
Figure 1.
Verifying processor usage in task manager
1 Right click on the desktop.
2 Select Start Task Manager.
The Windows Task Manager window is displayed.
3 Click the Performance tab in the Windows Task Manager window.
20 Technology and components
Verifying processor usage in resource monitor
1 Right click the desktop.
2 Select Start Task Manager.
The Windows Task Manager window is displayed.
3 Click the Performance tab in the Windows Task Manager window.
The processor performance details are displayed.
4 Click Open Resource Monitor.
Technology and components 21
Chipset
The chipset is integrated on the processor.
Identifying chipset in device manager on Windows 10
NOTE: The Chipset information displayed is a generic image and may be dierent from what is
displayed.
1 Click All Settings on the Windows 10 Charms Bar.
2 From the Control Panel, select Device Manager.
3 Expand System Devices and search for the chipset.
22 Technology and components
Memory features
Memory is integrated on the system board and it cannot be replaced as a module:
• DDR4 2400 MHz
• DDR4 2667 MHz (Non-ECC only)
Verifying system memory in setup
1 Turn on or restart your notebook.
2 Perform one of the following actions after the Dell logo is displayed:
• With keyboard — Tap F2 until the Entering BIOS setup message appears. To enter the Boot selection menu, tap F12.
3 On the left pane, select Settings > General > System Information,
The memory information is displayed on the right pane.
Verifying system memory
Windows 10
1 Click the Windows button and select All Settings > System .
2 Under System, click About.
Testing memory using ePSA
1 Turn on or restart your computer.
2 Perform one of the following actions after the Dell logo is displayed:
• With keyboard — Press F2.
Technology and components 23
The PreBoot System Assessment (PSA) starts on your computer.
NOTE: If you wait too long and the operating system logo appears, continue to wait until you see the desktop. Turn o
the computer and try again.
Display
Display section details on identifying the display adapter from the display manager along with steps on how change the screen resolution. It
also contains information about connecting multiple monitors.
Display options
• This laptop is shipped with 17.3-inch FHD Touch with Corning Gorilla Glass 4 (1920 x 1080) display.
• This laptop is shipped with 17.3-inch UHD Touch with Corning Gorilla Glass 4 (3840x2160) display.
Identifying display adapter
1 Type Device manager in the Ask me anything eld.
The Display Manager window is displayed.
2 Expand the Display adapters.
The display adapter information is displayed.
Figure 2. display adapter
Changing the screen resolution
1 Right click on the desktop and select Display Settings.
2 Tap or click Advanced display settings.
3 Select the required resolution from the drop-down list and tap Apply.
24 Technology and components
Connecting to external display devices
Follow these steps to connect your computer to an external display device:
1 Ensure that the projector is turned on and plug the projector cable into a video port on your computer.
2 Press the Windows logo+P key.
3 Select one of the following modes:
• PC screen only
• Duplicate
• Extend
• Second Screen only
NOTE: For more information, see the document that shipped with your display device.
Camera features
This laptop is shipped with front-facing camera with the image resolution of 1280 x 720 (maximum). Front facing IR camera is also available.
The camera is at the top center of the display.
Identifying the camera in Device Manager on Windows 10
1 In the Search box, type device manager, and tap to start it.
2 Under Device Manager, expand Imaging devices.
Starting the camera
To start the camera, open an application that uses the camera. For instance, if you tap the Dell webcam central software or the Skype
software that is shipped with the laptop, the camera turns on. Similarly, if you are chatting on the internet and the application requests to
access the webcam, the webcam turns on.
Starting the camera application
1 Tap or click the Windows button and select All apps.
2 Select Camera from the apps list.
Technology and components 25
3 If the Camera App is not available in the apps list, search for it.
Hard drive
This section explains how to identify the hard drive type installed in the system.
Storage options
This laptop supports M.2 SATA SSD and M.2 PCIe NVMe SSDs.
Identifying the storage device in the BIOS
1 Turn on or restart your laptop.
2 When the Dell logo appears, perform one of the following actions to enter the BIOS setup program:
• With keyboard — Tap F2 until the Entering BIOS setup message appears. To enter the Boot selection menu, tap F12.
• Without keyboard — When the F12 boot selection menu is displayed, use the arrow keys to choose the option to enter BIOS
setup.
26 Technology and components
Storage device (HDD or SSD type) is listed under the System Information under the General group.
Identifying storage device in Windows 10
1 Type Device Manager in I'm Cortana, Ask me anything eld.
The Device Manager window is displayed.
2 Click Disk Drives.
The storage devices installed in the system are displayed.
USB features
The Universal Serial Bus, or well known as USB was introduced to the PC world in 1996 which dramatically simplied the connection
between host computer and peripheral devices such as mice and keyboards, external hard drive or optical devices, Bluetooth and many
more peripheral devices in the market.
Let's take a quick look on the USB evolution referencing to the table below.
Table 1. USB evolution
Type Data Transfer Rate Category Introduction Year
USB 3.0/USB 3.1 Gen 1 5 Gbps Super Speed 2010
USB 2.0 480 Mbps High Speed 2000
USB 1.1 12 Mbps Full Speed 1998
USB 1.0 1.5 Mbps Low Speed 1996
USB 3.0/USB 3.1 Gen 1 (SuperSpeed USB)
For years, the USB 2.0 has been rmly entrenched as the de facto interface standard in the PC world with about 6 billion devices sold, and
yet the need for more speed grows by ever faster computing hardware and ever greater bandwidth demands. The USB 3.0/USB 3.1 Gen 1
nally has the answer to the consumers' demands with a theoretically 10 times faster than its predecessor. In a nutshell, USB 3.1 Gen 1
features are as follows:
• Higher transfer rates (up to 5 Gbps)
• Increased maximum bus power and increased device current draw to better accommodate power-hungry devices
• New power management features
• Full-duplex data transfers and support for new transfer types
• Backward USB 2.0 compatibility
• New connectors and cable
The topics below cover some of the most commonly asked questions regarding USB 3.0/USB 3.1 Gen 1.
Speed
Currently, there are 3 speed modes dened by the latest USB 3.0/USB 3.1 Gen 1 specication. They are Super-Speed, Hi-Speed and Full-
Speed. The new SuperSpeed mode has a transfer rate of 4.8Gbps. While the specication retains Hi-Speed, and Full-Speed USB mode,
Technology and components 27
commonly known as USB 2.0 and 1.1 respectively, the slower modes still operate at 480Mbps and 12Mbps respectively and are kept to
maintain backward compatibility.
USB 3.0/USB 3.1 Gen 1 achieves the much higher performance by the technical changes below:
• An additional physical bus that is added in parallel with the existing USB 2.0 bus (refer to the picture below).
• USB 2.0 previously had four wires (power, ground, and a pair for dierential data); USB 3.0/USB 3.1 Gen 1 adds four more for two pairs
of dierential signals (receive and transmit) for a combined total of eight connections in the connectors and cabling.
• USB 3.0/USB 3.1 Gen 1 utilizes the bidirectional data interface, rather than USB 2.0's half-duplex arrangement. This gives a 10-fold
increase in theoretical bandwidth.
With today's ever increasing demands placed on data transfers with high-denition video content, terabyte storage devices, high megapixel
count digital cameras etc., USB 2.0 may not be fast enough. Furthermore, no USB 2.0 connection could ever come close to the 480Mbps
theoretical maximum throughput, making data transfer at around 320Mbps (40MB/s) — the actual real-world maximum. Similarly, USB
3.0/USB 3.1 Gen 1 connections will never achieve 4.8Gbps. We will likely see a real-world maximum rate of 400MB/s with overheads. At this
speed, USB 3.0/USB 3.1 Gen 1 is a 10x improvement over USB 2.0.
Applications
USB 3.0/USB 3.1 Gen 1 opens up the laneways and provides more headroom for devices to deliver a better overall experience. Where USB
video was barely tolerable previously (both from a maximum resolution, latency, and video compression perspective), it's easy to imagine
that with 5-10 times the bandwidth available, USB video solutions should work that much better. Single-link DVI requires almost 2Gbps
throughput. Where 480Mbps was limiting, 5Gbps is more than promising. With its promised 4.8Gbps speed, the standard will nd its way
into some products that previously weren't USB territory, like external RAID storage systems.
Listed below are some of the available SuperSpeed USB 3.0/USB 3.1 Gen 1 products:
• External Desktop USB 3.0/USB 3.1 Gen 1 Hard Drives
• Portable USB 3.0/USB 3.1 Gen 1 Hard Drives
• USB 3.0/USB 3.1 Gen 1 Drive Docks & Adapters
• USB 3.0/USB 3.1 Gen 1 Flash Drives & Readers
• USB 3.0/USB 3.1 Gen 1 Solid-state Drives
• USB 3.0/USB 3.1 Gen 1 RAIDs
• Optical Media Drives
• Multimedia Devices
• Networking
• USB 3.0/USB 3.1 Gen 1 Adapter Cards & Hubs
28 Technology and components
Compatibility
The good news is that USB 3.0/USB 3.1 Gen 1 has been carefully planned from the start to peacefully co-exist with USB 2.0. First of all,
while USB 3.0/USB 3.1 Gen 1 species new physical connections and thus new cables to take advantage of the higher speed capability of
the new protocol, the connector itself remains the same rectangular shape with the four USB 2.0 contacts in the exact same location as
before. Five new connections to carry receive and transmitted data independently are present on USB 3.0/USB 3.1 Gen 1 cables and only
come into contact when connected to a proper SuperSpeed USB connection.
Windows 8/10 will be bringing native support for USB 3.1 Gen 1 controllers. This is in contrast to previous versions of Windows, which
continue to require separate drivers for USB 3.0/USB 3.1 Gen 1 controllers.
Microsoft announced that Windows 7 would have USB 3.1 Gen 1 support, perhaps not on its immediate release, but in a subsequent Service
Pack or update. It is not out of the question to think that following a successful release of USB 3.0/USB 3.1 Gen 1 support in Windows 7,
SuperSpeed support would trickle down to Vista. Microsoft has conrmed this by stating that most of their partners share the opinion that
Vista should also support USB 3.0/USB 3.1 Gen 1.
Super-Speed support for Windows XP is unknown at this point. Given that XP is a seven-year-old operating system, the likelihood of this
happening is remote.
HDMI 1.4
This topic explains the HDMI 1.4 and its features along with the advantages.
HDMI (High-Denition Multimedia Interface) is an industry-supported, uncompressed, all-digital audio/video interface. HDMI provides an
interface between any compatible digital audio/video source, such as a DVD player, or A/V receiver and a compatible digital audio and/or
video monitor, such as a digital TV (DTV). The intended applications for HDMI TVs, and DVD players. The primary advantage is cable
reduction and content protection provisions. HDMI supports standard, enhanced, or high-denition video, plus multichannel digital audio on
a single cable.
NOTE: The HDMI 1.4 will provide 5.1 channel audio support.
HDMI 1.4 Features
•HDMI Ethernet Channel - Adds high-speed networking to an HDMI link, allowing users to take full advantage of their IP-enabled
devices without a separate Ethernet cable
•Audio Return Channel - Allows an HDMI-connected TV with a built-in tuner to send audio data "upstream" to a surround audio system,
eliminating the need for a separate audio cable
•3D - Denes input/output protocols for major 3D video formats, paving the way for true 3D gaming and 3D home theater applications
•Content Type - Real-time signaling of content types between display and source devices, enabling a TV to optimize picture settings
based on content type
•Additional Color Spaces - Adds support for additional color models used in digital photography and computer graphics
•4 K Support - Enables video resolutions far beyond 1080p, supporting next-generation displays that will rival the Digital Cinema systems
used in many commercial movie theaters
•HDMI Micro Connector - A new, smaller connector for phones and other portable devices, supporting video resolutions up to 1080p
•Automotive Connection System - New cables and connectors for automotive video systems, designed to meet the unique demands of
the motoring environment while delivering true HD quality
Advantages of HDMI
• Quality HDMI transfers uncompressed digital audio and video for the highest, crispest image quality.
• Low -cost HDMI provides the quality and functionality of a digital interface while also supporting uncompressed video formats in a
simple, cost-eective manner
Technology and components 29
• Audio HDMI supports multiple audio formats from standard stereo to multichannel surround sound
• HDMI combines video and multichannel audio into a single cable, eliminating the cost, complexity, and confusion of multiple cables
currently used in A/V systems
• HDMI supports communication between the video source (such as a DVD player) and the DTV, enabling new functionality
30 Technology and components
Technical specications
NOTE: Oerings may vary by region. The following specications are only those required by law to ship with your computer. For
more information about the conguration of your computer, go to Help and Support in your Windows operating system and
select the option to view information about your computer.
Topics:
• System information
• Processor
• Memory
• Video
• Audio
• Communication
• Expansion bus
• Ports and connectors
• Display
• Keyboard
• Touchpad
• Camera
• Storage
• Battery
• AC adpter
• Contactless smart card
• Physical dimension
• Environmental
System information
Feature Specication
System Chipset Intel CM238 Chipset
Interrupt Levels Interrupt Controller
• Supports up to eight legacy interrupt pins
• Supports PCI 2.3 Message Signaled
Interrupts
• Integrated IO APIC capability with 24 interrupts
• Supports Processor System Bus interrupt delivery
BIOS Chip
(NVRAM)
64Mbit (8MB) & 32Mbit (4MB)
4
Technical specications 31
Processor
Feature Specication
Processor type • 6th generation Intel i7, Xeon processors (SkyLake)
• 7th generation Intel Core i5, i7 and Xeon processors (KabyLake)
L1 cache Up to 32 KB cache depending on processor type
L2 cache Up to 256 KB cache depending on processor type
L3 cache Up to 8 MB cache depending on processor type
Intel Smart cache
with Last Level
Cache
Up to 8 MB cache depending on processor type
Memory
Feature Specication
Type DDR4 SDRAM
Speed • 2400 MHz
• 2667 MHz (Non-ECC only)
Connectors 4
Capacity 8GB, 16 GB
Minimum Memory 8 GB ( 1 x 8 GB)
Maximum memory 64 GB
Video
Feature Specication
Type MXM type-B add-in card
Data bus PCIE x16, Gen3
Video controller and
memory: • Radeon Pro WX 4130 w/2GB GDDR5
• NVIDIA Quadro M1200 w/4GB GDDR5
• NVIDIA Quadro P3000 w/6GB GDDR5
• Radeon Pro WX 7100 w/8GB GDDR5
• NVIDIA Quadro P4000 w/8GB GDDR5
• NVIDIA Quadro P5000 w/16GB GDDR5
Audio
Features Specication
32 Technical specications
Integrated dual-channel High-Denition audio
Communication
Feature Specication
Ethernet adapter network interface card capable of 10/100/1000 mb/s communication
Wireless WLAN options:
• Intel WiFi Link 8265 2x2 802.11ac+BT 4.2 (vPro)
• Intel WiFi Link 8265 2x2 802.11ac NBT (vPro)
• Dell DW 1820 2x2 802.11ac+BT 4.2 US
Optional Mobile broadband and GPS
• DW5811e (Gobi 4G/LTE - FMC)
• DW5814e (Gobi 4G/LTE)
Expansion bus
Feature Specication
Bus Type PCI Express 1.0, 2.0 and 3.0, SATA 1.0A, 2.0 and 3.0, USB 2.0 and 3.0
Bus Width PCIe X16
BIOS Chip
(NVRAM)
128 Mb (16 MB)
Ports and connectors
Feature Specication
Audio Universal audio jack connector
Network Adapter one RJ45 connector
USB C connector
with Thunderbolt
one (optional)
USB 3.1 with Gen 1
(with PowerShare)
four
Video HDMI 1.4, mDP 1.4
Memory card reader SD 4.0
Docking port one
Micro Subscriber
Identity Module
(Micro SIM) port
one
Smart card
(optional)
one
Technical specications 33
Display
Features Specication
Type • FHD (1920 x 1080)
• UHD (3840 x 2160)
Size 17.3 inches
Dimensions:
Height 214.92 mm (8.42 inches)
Width 382.08 mm (15.04 inches)
Diagonal 438.38 mm (17.25 inches)
Active area (X/Y) • FHD (1920 x 1080)
• UHD (3840 x 2160)
Maximum resolution • FHD (1920 x 1080)
• UHD (3840 x 2160)
Maximum
Brightness • FHD (300 nits)
• UHD (400 nits)
Operating angle 0° (closed) to 135°
Refresh rate 60 Hz
Minimum viewing
angles:
Horizontal/\ • FHD (40/80)
• UHD (80)
Vertical • FHD (10/80)
• UHD (80)
Keyboard
Features Specication
Number of keys • United States: 103 keys
• United Kingdom: 104 keys
• Brazil: 106 keys
• Japan: 107 keys
Layout QWERTY/AZERTY/Kanji
34 Technical specications
Touchpad
Features Specication
X/Y position
resolution • X: 41.27+-4.13 counts/mm
• Y: 38.75+-3.88 counts/mm
• 1048/984 cpi
Size Sensor-active area:
• Width: 99.5mm (3.92 inches)
• Height: 53mm (2.09 inches)
Multi-Touch Congurable single nger and multi-nger gestures
Camera
Features Specication
Type CMOS Sensor
Still Resolution 1280 x 720 Pixels (Maximum)
Video Resolution 1280 x 720 Pixels (Maximum)
Diagonal 74 degrees
Storage
Features Specication
Storage: • SATA 1 (1.5 Gb/s)
• SATA 2 (3.0 Gb/s)
• SATA 3 (6 Gb/s)
• PCIe express
Size 1 TB 5400 rpm, 128/256/512 GB SATA 3 SSD, 256 GB SATA 3 SSD, 1 TB M.2 SSD, 1 TB SATA 3 SSD
Battery
Features Specication
Wattage 91Whr/ 88Whr
Type lithium ion
Dimensions (6-cell
entry/ 6-cell upsell/
6-cell long cycle life
(LCL)):
1280 x 720 Pixels (Maximum)
Length 243.89 mm (9.6 inches)
Technical specications 35
Height 18.45 mm (0.73inches)
Width 71.30 mm (2.81inches)
Weight 18.45 mm (0.73inches")
Voltage 400.00 g (0.88 lb)
Life span • 300 discharge/charge cycles
• 1000 discharge/charge cycles (LCL)
Temperature range:
Operating • Charge: 0°C to 50°C (32°F to 158°F)
• Discharge: 0°C to 70°C (32°F to 122°F)
Non-Operating -20°C to 65°C (4°F to 149°F)
Coin-cell battery 3 V CR2032 lithium ion cell
AC adpter
Features Specication
Input voltage 100 VAC to 240 VAC
Input current
(maximum)
3.50 A
Input frequency 50 Hz to 60 Hz
Output power 240 W
Output current 12.31 A
Rated output
voltage
19.50 VDC
Dimensions: 240 W
Height 25.40 mm (1 inch)
Width 200 mm (7.87 inches)
Depth 100 mm (3.94 inches)
Weight 0.85 kg (1.88 lb)
Temperature range:
Operating 0°C to 40°C (32°F to 104°F)
Non-Operating –40°C to 70°C (–40°F to 158°F)
Contactless smart card
Features Specication
Supported Smart
Cards and
technologies
• ISO14443A — 160 kbps, 212 kbps, 424 kbps, and 848 kbps
• ISO14443B — 160 kbps, 212 kbps, 424 kbps, and 848 kbps
• ISO15693
36 Technical specications
• HID iClass
• FIPS201
• NXP Desre
Physical dimension
Feature Specication
Weight (pounds/
kilograms)
7.5 lbs (3.40 kgs)
Dimensions
Height (inches/mm)
Front (non-touch) 1.13 inches ( 28.7mm)
Rear (non-touch) 1.39 inches (35.3mm)
Width (inches/mm) 16.41 inches (416.7mm)
Depth (inches/mm) 11.07 inches (281.2 mm)
Environmental
Feature Specication
Temperature range:
Operating 0°C to 40°C (32°F to 104°F)
Storage –40°C to 65 °C (–40°F to 149°F)
Relative humidity
(maximum):
Operating 10 % to 90 % (non-condensing)
Storage 5 % to 95 % (non-condensing)
Maximum vibration:
Operating 0.66 GRMS, 2 Hz — 600 Hz
Storage 0.66 GRMS, 2 Hz — 600 Hz
Maximum shock:
Operating 140 G, 2 MS
Storage 163 G, 2 MS
Altitude:
Storage 0 -m to 10,668 -m (0 ft to 35,000 ft)
Airborne
contaminant level
G1 or lower as dened by ANSI/ISA-S71.04-1985
Technical specications 37
System setup
System Setup enables you to manage your notebook hardware and specify BIOS level options. From the System Setup, you can:
• Change the NVRAM settings after you add or remove hardware
• View the system hardware conguration
• Enable or disable integrated devices
• Set performance and power management thresholds
• Manage your computer security
Topics:
• Boot menu
• Navigation keys
• System setup options
• Virtualization support screen options
• Wireless screen options
• Maintenance screen options
• System Log screen options
• Updating the BIOS
• System and setup password
Boot menu
Press <F12> when the Dell logo appears to initiate a one-time boot menu with a list of the valid boot devices for the system. Diagnostics
and BIOS Setup options are also included in this menu. The devices listed on the boot menu depend on the bootable devices in the system.
This menu is useful when you are attempting to boot to a particular device or to bring up the diagnostics for the system. Using the boot
menu does not make any changes to the boot order stored in the BIOS.
The options are:
• Legacy Boot:
• Internal HDD
• Onboard NIC
• USB optical drive (if available)
• UEFI Boot:
• Windows Boot Manager
• Other Options:
• BIOS Setup
• BIOS Flash Update
• Diagnostics
• Change Boot Mode Settings
5
38 System setup
Navigation keys
NOTE: For most of the System Setup options, changes that you make are recorded but do not take eect until you restart the
system.
Keys Navigation
Up arrow Moves to the previous eld.
Down arrow Moves to the next eld.
Enter Selects a value in the selected eld (if applicable) or follow the link in the eld.
Spacebar Expands or collapses a drop‐down list, if applicable.
Tab Moves to the next focus area.
NOTE: For the standard graphics browser only.
Esc Moves to the previous page until you view the main screen. Pressing Esc in the main screen displays a message
that prompts you to save any unsaved changes and restarts the system.
F1 Displays the System Setup help le.
System setup options
NOTE: Depending on the notebook and its installed devices, the items listed in this section may or may not appear.
General screen options
This section lists the primary hardware features of your computer.
Option Description
System Information This section lists the primary hardware features of your computer.
• System Information: Displays BIOS Version, Service Tag, Asset Tag, Ownership Tag, Ownership Date,
Manufacture Date, and the Express Service Code.
• Memory Information: Displays Memory Installed, Memory Available, Memory Speed, Memory Channels Mode,
Memory Technology, DIMM ASize, DIMM B Size, DIMM CSize, DIMM D Size,
• Processor Information: Displays Processor Type, Core Count, Processor ID, Current Clock Speed, Minimum
Clock Speed, Maximum Clock Speed, Processor L2 Cache, Processor L3 Cache, HT Capable, and 64-Bit
Technology.
• Device Information: Displays Primary Hard Drive, SATA-0, M.2 PCIe SSD-0, M.2 PCIe SSD-1, Dock eSATA
Device, LOM MAC Address, Passthrough MAc address, Video Controller, dGPU video controller, Video BIOS
Version, Video Memory, Panel Type, Native Resolution, Audio Controller, Wi-Fi Device, Cellular Device,
Bluetooth Device.
Battery Information Displays the battery status and the type of AC adapter connected to the computer.
Boot Sequence Allows you to change the order in which the computer attempts to nd an operating system.
• Windows Boot Manager
• Boot list options:
• Legacy
• Diskette Drive
• Internal HDD
• USB Storage Device
System setup 39
Option Description
• CD/DVD/CD-RW Drive
• Onboard NIC
• UEFI (selected by default)
Advanced Boot
Options
This option allows you the legacy option ROMs to load. By default, the Enable Legacy Option ROMs is enabled.
• Enable Attempt Legacy Boot
UEFI boot path
security • Always, except internal HDD (selected by default)
• Always
• Never
Date/Time Allows you to change the date and time.
System Conguration screen options
Option Description
Integrated NIC Allows you to congure the integrated network controller. The options are:
• Enable UEFI Network Stack
• Disabled
• Enabled
• Enabled w/PXE: This option is enabled by default.
Parallel Port Allows you to congure the parallel port on the docking station. The options are:
• Disabled
• AT: This option is enabled by default.
• PS2
• ECP
Serial Port Allows you to congure the integrated serial port. The options are:
• Disabled
• COM1: This option is selected by default.
• COM2
• COM3
• COM4
SATA Operation Allows you to congure the internal SATA hard-drive controller. The options are:
• Disabled
• AHCI
• RAID On: This option is enabled by default.
Drives Allows you to congure the SATA drives on board. All drives are enabled by default. The options are:
• SATA-0
• SATA-1
40 System setup
Option Description
• SATA-4
• M.2 PCI-e SSD-0
• M.2 PCIe SSD-1
• SATA-3
SMART Reporting This eld controls whether hard drive errors for integrated drives are reported during system startup. This
technology is part of the SMART (Self Monitoring Analysis and Reporting Technology) specication. This option is
disabled by default.
• Enable SMART Reporting
USB Conguration This is an optional feature.
This eld congures the integrated USB controller. If Boot Support is enabled, the system is allowed to boot any
type of USB Mass Storage Devices (HDD, memory key, oppy).
If USB port is enabled, device attached to this port is enabled and available for OS.
If USB port is disabled, the OS cannot see any device attached to this port.
The options are:
• Enable Boot support (by default enable)
• Enable Thunderbolt ports (by default enable)
• Always Allow dell docks
• Enable external USB ports
Others:
• Enable Thubderbolt Boot Support
• Enable Thunderbolt (and PCIE behind TBT) Pre-boot
• Security level-no security
• Security level-user conguration (selected by default)
• Security level-secure connect
• Security level- Display port only
NOTE: USB keyboard and mouse always work in the BIOS setup irrespective of these settings.
USB PowerShare This eld congures the USB PowerShare feature behavior. This option allows you to charge external devices using
the stored system battery power through the USB PowerShare port (disabled by default)..
Audio This eld enables or disables the integrated audio controller. By default, the Enable Audio option is selected. The
options are:
• Enable Microphone (by default enable)
• Enable Internal Speaker (by default enable)
Keyboard
Illumination
This eld lets you choose the operating mode of the keyboard illumination feature. The keyboard brightness level
can be set from 0% to 100%. The options are:
• Disabled (selected by default)
• Dim
• Bright
System setup 41
Option Description
Keyboard Backlight
with AC
The Keyboard Backlight with AC option does not aect the main keyboard illumination feature. Keyboard
Illumination will continue to support the various illumination levels. This eld has an eect when the backlight is
enabled (selected by default).
Keyboard Backlight
Timeout on AC
The Keyboard Backlight Time-out dims out with AC option. The main keyboard illumination feature is not aected.
Keyboard Illumination will continue to support the various illumination levels. This eld has an eect when the
backlight is enabled.
• 5 sec
• 10 sec (selected by default)
• 15 sec
• 30 sec
• 1 min
• 5 min
• 15 min
• never
Keyboard Backlight
Timeout on Battery
The Keyboard Backlight Time-out dims out with Battery option. The main keyboard illumination feature is not
aected. Keyboard Illumination will continue to support the various illumination levels. This eld has an eect when
the backlight is enabled.
• 5 sec
• 10 sec (selected by default)
• 15 sec
• 30 sec
• 1 min
• 5 min
• 15 min
• never
Unobtrusive Mode This option, when enabled, pressing Fn+F7 turns o all light and sound emissions in the system. To resume normal
operation, press Fn+F7 again. This option is disabled by default.
Miscellaneous
Devices
Allows you to enable or disable the following devices:
• Enable Camera —enabled by default
• Enable Expresscard (selected by default)
• Enable HardDrive Free Fall Protection (selected by default)
• WiFI Radio (selected by default)
• Enable Secure Digital (SD) Card (selected by default)
• Secure Digital (SD) Card Read-Only Mode
• Secure Digital (SD) Card Boot
Video screen options
Option Description
LCD Brightness Allows you to set the display brightness depending upon the power source. On Battery(50% is default) and On AC
(100 % default).
42 System setup
Option Description
Switchable
Graphics • Enable Switchable Graphics (selected by default)
• Enable Dock Display Port(selected by default)
• Graphics Spec Mode
NOTE: The video setting will be visible only when a video card is installed into the system.
Security screen options
Option Description
Admin Password Allows you to set, change, or delete the administrator (admin) password.
NOTE: You must set the admin password before you set the system or hard drive password. Deleting
the admin password automatically deletes the system password and the hard drive password.
NOTE: Successful password changes take eect immediately.
Default setting: Not set
System Password Allows you to set, change or delete the system password.
NOTE: Successful password changes take eect immediately.
Default setting: Not set
Internal HDD-2
Password
Allows you to set, change, or delete the administrator password.
NOTE: Successful password changes take eect immediately.
Default setting: Not set
Strong Password Allows you to enforce the option to always set strong passwords.
Default Setting: Enable Strong Password is not selected.
NOTE: If Strong Password is enabled, Admin and System passwords must contain at least one
uppercase character, one lowercase character and be at least 8 characters long.
Password
Conguration
Allows you to specify the minimum and max password lengths of Administrator and System passwords.
• minimum -4(by default, if you want to change you can increase the number)
• maximum -32 ( you can decrease the number)
Password Bypass Allows you to enable or disable the permission to bypass the System and the Internal HDD password, when they
are set. The options are:
• Disabled
• Reboot bypass
Default setting: Disabled
Password Change Allows you to enable the disable permission to the System and Hard Drive passwords when the admin password is
set.
System setup 43
Option Description
Default setting: Allow Non-Admin Password Changes is selected.
Non-Admin Setup
Changes
Allows you to determine whether changes to the setup options are allowed when an Administrator Password is set.
If disabled the setup options are locked by the admin password.
• allow wireless switch changes
UEFI Capsule
Firmware Updates
Allows you to enable or disable. This option controls whether this system allows BIOS updated via UEFI capsule
update packages. The options are:
• Enable UEFI Capsule Firmware—enabled by default
Computrace Allows you to activate or disable the optional Computrace software The options are:
• Deactivate
• Disable
• Activate (selected by default)
NOTE: The Activate and Disable options will permanently activate or disable the feature and no further
changes will be allowed
CPU XD Support Allows you to enable the Execute Disable mode of the processor.
Enable CPU XD Support (default)
OROM Keyboard
Access
Allows you to set an option to enter the Option ROM Conguration screens using hotkeys during boot. The options
are:
• Enable
• One Time Enable
• Disable
Default setting: Enable
Admin Setup
Lockout
Allows you to prevent users from entering Setup when an Administrator password is set.
Default Setting: Disabled
Master password
lockout
This option is not selected by default
Secure Boot screen options
Option Description
Secure Boot Enable This option enables or disables the Secure Boot feature.
• Disabled
• Enabled
Default setting: Enabled.
Expert Key
Management
Allows you to manipulate the security key databases only if the system is in Custom Mode. The Enable Custom
Mode option is disabled by default. The options are:
44 System setup
Option Description
• PK—enabled by default
• KEK
• db
• dbx
If you enable the Custom Mode, the relevant options for PK, KEK, db, and dbx appear. The options are:
• Save to File—Saves the key to a user-selected le
• Replace from File—Replaces the current key with a key from a user-selected le
• Append from File—Adds a key to the current database from a user-selected le
• Delete—Deletes the selected key
• Reset All Keys—Resets to default setting
• Delete All Keys—Deletes all the keys
NOTE: If you disable the Custom Mode, all the changes made are erased and the keys restore to default
settings.
Intel Software Guard Extensions screen options
Option Description
Intel SGX Enable This eld species you to provide a secured environment for running code/storing sensitive information in the
context of the main OS. The options are:
• Disabled
• Enabled
• Software controlled (default)
Enclave Memory
Size
This option sets SGX Enclave Reserve Memory Size. The options are:
• 32 MB
• 64 MB
• 128 MB (default)
Performance screen options
Option Description
Multi Core Support This eld species whether the process has one or all cores enabled. The performance of some applications
improves with the additional cores. This option is enabled by default. Allows you to enable or disable multi-core
support for the processor. The installed processor supports two cores. If you enable Multi Core Support, two cores
are enabled. If you disable Multi Core Support, one core is enabled.
• All (selected by default)
• 1
• 2
• 3
Intel SpeedStep Allows you to enable or disable the Intel SpeedStep feature.
System setup 45
Option Description
• Enable Intel SpeedStep
Default setting: The option is enabled.
C-States Control Allows you to enable or disable the additional processor sleep states.
• C states
Default setting: The option is enabled.
Intel TurboBoost Allows you to enable or disable the Intel TurboBoost mode of the processor.
• Enable Intel TurboBoost
Default setting: The option is enabled.
Hyper-Thread
Control
Allows you to enable or disable the Hyper-Threading in the processor.
• Disabled
• Enabled
Default setting: Enabled.
Power Management screen options
Option Description
AC Behavior Allows you to enable or disable the computer from turning on automatically when an AC adapter is connected.
Default setting: Wake on AC is not selected.
Auto On Time Allows you to set the time at which the computer must turn on automatically. The options are:
• Disabled
• Every Day
• Weekdays
• Select Days
Default setting: Disabled
Deep Sleep Control • Disabled (selected by default)
• Enabled in S5 only
• Enabled in S4 and S5
USB Wake Support Allows you to enable USB devices to wake the system from Standby.
NOTE: This feature is only functional when the AC power adapter is connected. If the AC power
adapter is removed during Standby, the system setup removes power from all the USB ports to
conserve battery power.
• Enable USB Wake Support
• Wake on Dell USB-C dock
46 System setup
Option Description
Wireless Radio
Control
Allows you to enable or disable the feature that automatically switches from wired or wireless networks without
depending on the physical connection.
• Control WLAN Radio
• Control WWAN Radio
Wake on LAN/
WLAN
Allows you to enable or disable the feature that powers on the computer from the O state when triggered by a
LAN signal.
• Disabled
• LAN Only
• WLAN Only
• LAN or WLAN
Default setting: Disabled
Peak Shift This option enables you to minimize the AC power consumption during the peak power times of day. After you
enable this option, your system runs only in battery even if the AC is attached.
• Enable peak shift (disabled)
• Set battery threshold
Advanced Battery
Charge
Conguration
This option enables you to maximize the battery health. By enabling this option, your system uses the standard
charging algorithm and other techniques, during the non-work hours to improve the battery health.
Primary Battery
Charge
Conguration
Allows you to select the charging mode for the battery. The options are:
• Adaptive (default)
• Standard — Fully charges your battery at a standard rate.
• ExpressCharge — The battery charges over a shorter period of time using Dell’s fast charging technology. This
option is enabled by default.
• Primarily AC use
• Custom
If Custom Charge is selected, you can also congure Custom Charge Start and Custom Charge Stop.
NOTE: All charging mode may not be available for all the batteries. To enable this option, disable the
Advanced Battery Charge Conguration option.
Type-C connector
power • 7.5 Watts(selected by default)
• 15 Watts
POST Behavior screen options
Option Description
Adapter Warnings Allows you to enable or disable the system setup (BIOS) warning messages when you use certain power adapters.
Default setting: Enable Adapter Warnings
Keypad
(Embedded)
Allows you to choose one of two methods to enable the keypad that is embedded in the internal keyboard.
System setup 47
Option Description
• Fn Key Only: This option is enabled by default.
• By Numlock
NOTE: When setup is running, this option has no eect. Setup works in Fn Key Only
mode.
Mouse/Touchpad Allows you to dene how the system handles mouse and touch pad input. The options are:
• Serial Mouse
• PS2 Mouse
• Touchpad/PS-2 Mouse: This option is enabled by default.
Numlock Enable Allows you to enable the Numlock option when the computer boots.
Enable Numlock. This option is enabled by default.
Fn Key Emulation Allows you to set the option where the Scroll Lock key is used to simulate the Fn key feature.
Enable Fn Key Emulation (selected by default)
Fn Lock Options Allows you to let hot key combinations Fn + Esc toggle the primary behavior of F1–F12, between their standard
and secondary functions. If you disable this option, you cannot toggle dynamically the primary behavior of these
keys. The available options are:
• Fn Lock. This option is selected by default.
• Lock Mode Disable/Standard (selected by default.)
• Lock Mode Enable/Secondary
Manageability screen options
Option Description
MEBx Hotkey Allows you to specify whether the MEBx Hotkey function should enable, during the system boot.
Default Setting: Enable MEBx Hotkey
Fastboot Allows you to speed up the boot process by bypassing some of the compatibility steps. The options are:
• Minimal (default)
• Thorough
• Auto
Extended BIOS
POST Time
Allows you to create an additional preboot delay. The options are:
• 0 seconds. This option is enabled by default.
• 5 seconds
• 10 seconds
Full Screen Log Allows you to specify whether the Full Screen Log (disabled by default).
Warnings and errors
option • Prompt on warnings and errors (selected by default)
• Continue on warnings
48 System setup
Option Description
• Continue on warnings and errors
Virtualization support screen options
Option Description
Virtualization Allows you to enable or disable the Intel Virtualization Technology.
Enable Intel Virtualization Technology (default).
VT for Direct I/O Enables or disables the Virtual Machine Monitor (VMM) from utilizing the additional hardware capabilities provided
by Intel® Virtualization technology for direct I/O.
Enable VT for Direct I/O - enabled by default.
Wireless screen options
Option Description
Wireless Switch Allows to set the wireless devices that can be controlled by the wireless switch. The options are:
• WWAN
• GPS (on WWAN Module)
• WLAN
• Bluetooth
All the options are enabled by default.
NOTE: For WLAN and WiGig enable or disable controls are tied together and they cannot be enabled or
disabled independently.
Wireless Device
Enable
Allows you to enable or disable the internal wireless devices.
• WWAN/GPS
• WLAN
• Bluetooth
All the options are enabled by default.
Maintenance screen options
Option Description
Service Tag Displays the Service Tag of your computer.
Asset Tag Allows you to create a system asset tag if an asset tag is not already set. This option is not set by default.
BIOS Downgrade This controls ashing of the system rmware to previous revisions (selected by default).
Data Wipe This eld allows users to erase the data securely from all internal storage devices. The following is list of devices
aected:
• Wwipe on next boot (disabled)
• Internal SATA HDD/SSD
• Internal M.2 SATA SDD
System setup 49
Option Description
• Internal M.2 PCIe SSD
• Internal eMMC
BIOS Recovery This eld allows you to recover from certain corrupted BIOS conditions from a recover le on the user primary hard
drive or an external USB key.
• BIOS Recovery from Hard Drive (enabled by default)
• BIOS Auto-Recovery
• Always perform integrity check (disabled by default)
System Log screen options
Option Description
BIOS Events Allows you to view and clear the System Setup (BIOS) POST events.
Thermal Events Allows you to view and clear the System Setup (Thermal) events.
Power Events Allows you to view and clear the System Setup (Power) events.
Updating the BIOS
It is recommended to update your BIOS (System Setup), on replacing the system board or if an update is available. For laptops, ensure that
your computer battery is fully charged and connected to a power outlet
1 Restart the computer.
2 Go to Dell.com/support.
3 Enter the Service Tag or Express Service Code and click Submit.
NOTE: To locate the Service Tag, click Where is my Service Tag?
NOTE: If you cannot nd your Service Tag, click Detect My Product. Proceed with the instructions on
screen.
4 If you are unable to locate or nd the Service Tag, click the Product Category of your computer.
5 Choose the Product Type from the list.
6 Select your computer model and the Product Support page of your computer appears.
7 Click Get drivers and click View All Drivers.
The Drivers and Downloads page opens.
8 On the Drivers and Downloads screen, under the Operating System drop-down list, select BIOS.
9 Identify the latest BIOS le and click Download File.
You can also analyze which drivers need an update. To do this for your product, click Analyze System for Updates and follow the
instructions on the screen.
10 Select your preferred download method in the Please select your download method below window, click Download File.
The File Download window appears.
11 Click Save to save the le on your computer.
12 Click Run to install the updated BIOS settings on your computer.
Follow the instructions on the screen.
NOTE: It is recommended not to update the BIOS version for more than 3 revisions. For example: If you want to update the BIOS
from 1.0 to 7.0, then install version 4.0 rst and then install version 7.0.
50 System setup
System and setup password
You can create a system password and a setup password to secure your computer.
Password type Description
System password Password that you must enter to log on to your system.
Setup password Password that you must enter to access and make changes to the BIOS settings of your computer.
CAUTION: The password features provide a basic level of security for the data on your computer.
CAUTION: Anyone can access the data stored on your computer if it is not locked and left unattended.
NOTE: Your computer is shipped with the system and setup password feature disabled.
Assigning a system password and setup password
You can assign a new System Password only when the status is in Not Set.
NOTE: If the password jumper is disabled, the existing System Password and Setup Password are deleted and you need not
provide the system password to log on to the notebook.
To enter the system setup, press F2 immediately after a power-on or re-boot.
1 In the System BIOS or System Setup screen, select Security and press Enter.
The Security screen is displayed.
2 Select System Password and create a password in the Enter the new password eld.
Use the following guidelines to assign the system password:
• A password can have up to 32 characters.
• The password can contain the numbers 0 through 9.
• Only lower case letters are valid, upper case letters are not allowed.
• Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).
3 Type the system password that you entered earlier in the Conrm new password eld and click OK.
4 Press Esc and a message prompts you to save the changes.
5 Press Y to save the changes.
The computer reboots.
Deleting or changing an existing system and/or setup
password
Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or change the existing System and/or
Setup password. You cannot delete or change an existing System or Setup password, if the Password Status is Locked.
To enter the System Setup, press F2 immediately after a power-on or reboot.
1 In the System BIOS or System Setup screen, select System Security and press Enter.
The System Security screen is displayed.
2 In the System Security screen, verify that Password Status is Unlocked.
3 Select System Password, alter or delete the existing system password and press Enter or Tab.
4 Select Setup Password, alter or delete the existing setup password and press Enter or Tab.
NOTE: If you change the System and/or Setup password, re-enter the new password when promoted. If you delete the
System and/or Setup password, conrm the deletion when promoted.
System setup 51
5 Press Esc and a message prompts you to save the changes.
6 Press Y to save the changes and exit from System Setup.
The computer reboots.
52 System setup
Troubleshooting
Enhanced Pre-Boot System Assessment (ePSA)
diagnostics
The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware. The ePSA is embedded with the
BIOS and is launched by the BIOS internally. The embedded system diagnostics provides a set of options for particular devices or device
groups allowing you to:
• Run tests automatically or in an interactive mode
• Repeat tests
• Display or save test results
• Run thorough tests to introduce additional test options to provide extra information about the failed device(s)
• View status messages that inform you if tests are completed successfully
• View error messages that inform you of problems encountered during testing
CAUTION: Use the system diagnostics to test only your computer. Using this program with other computers may cause invalid
results or error messages.
NOTE: Some tests for specic devices require user interaction. Always ensure that you are present at the computer terminal
when the diagnostic tests are performed.
Running the ePSA diagnostics
1 Power-on the computer.
2 As the computer boots, press the F12 key as the Dell logo appears.
3 On the boot menu screen, select the Diagnostics option.
The Enhanced Pre-boot System Assessment window is displayed, listing all devices detected in the computer. The diagnostics starts
running the tests on all the detected devices.
4 To run a diagnostic test on a specic device, press Esc and click Yes to stop the diagnostic test.
5 Select the device from the left pane and click Run Tests.
6 If there are any issues, error codes are displayed.
Note the error code and contact Dell.
Device status lights
Table 2. Device status lights
Turns on when you turn on the computer and blinks when the computer is in a power management mode.
Turns on when the computer reads or writes data.
Turns on steadily or blinks to indicate battery charge status.
Turns on when wireless networking is enabled.
6
Troubleshooting 53
The device status LEDs are usually located either on the top or left side of the keyboard. They are used to display the storage, battery and
wireless devices connectivity and activity. Apart from that they can be useful as a diagnostic tool when there's a possible failure to the
system.
The following table lists how to read the LED codes when possible errors occur.
Table 3. LED lights
Storage LED Power LED Wireless LED Fault Description
Blinking Solid Solid A possible processor failure has occurred.
Solid Blinking Solid The memory modules are detected but has encountered an error.
Blinking Blinking Blinking A system board failure has occurred.
Blinking Blinking Solid A possible graphics card/video failure has occurred.
Blinking Blinking O System failed on hard drive initialization OR System failed in Option ROM
initialization.
Blinking O Blinking The USB controller encountered a problem during initialization.
Solid Blinking Blinking No memory modules are installed/detected.
Blinking Solid Blinking The display encountered a problem during initialization.
O Blinking Blinking The modem is preventing the system from completing POST.
O Blinking O Memory failed to initialize or memory is unsupported.
Battery status lights
If the computer is connected to an electrical outlet, the battery light operates as follows:
Alternately blinking
amber light and
white light
An unauthenticated or unsupported non-Dell AC adapter is attached to your laptop.
Alternately blinking
amber light with
steady white light
Temporary battery failure with AC adapter present.
Constantly blinking
amber light
Fatal battery failure with AC adapter present.
Light o Battery in full charge mode with AC adapter present.
White light on Battery in charge mode with AC adapter present.
Real Time Clock (RTC) reset
The Real Time Clock (RTC) reset function allows you or the service technician to recover the recently launched model Dell Latitude and
Precision systems from select No POST/No Boot/No Power situations. You can initiate the RTC reset on the system from a power o
state only if it is connected to AC power. Press and hold the power button for 25 seconds. The system RTC reset occurs after you release
the power button.
NOTE: If AC power is disconnected from the system during the process or the power button is held longer than 40 seconds, the
RTC reset process is aborted.
The RTC reset will reset the BIOS to Defaults, un-provision Intel vPro and reset the system date and time. The following items are
unaected by the RTC reset:
54 Troubleshooting
• Service Tag
• Asset Tag
• Ownership Tag
• Admin Password
• System Password
• HDD Password
• Key Databases
• System Logs
The following items may or may not reset based on your custom BIOS setting selections:
• The Boot List
• Enable Legacy OROMs
• Secure Boot Enable
• Allow BIOS Downgrade
Troubleshooting 55
Contacting Dell
NOTE: If you do not have an active Internet connection, you can nd contact information on your purchase invoice, packing slip,
bill, or Dell product catalog.
Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services
may not be available in your area. To contact Dell for sales, technical support, or customer service issues:
1 Go to Dell.com/support.
2 Select your support category.
3 Verify your country or region in the Choose a Country/Region drop-down list at the bottom of the page.
4 Select the appropriate service or support link based on your need.
7
56 Contacting Dell