Dell PowerEdge R430 Owner's Manual
About your system
Performing initial system configuration
Pre-operating system management applications
Installing and removing system components
Troubleshooting your system
Using system diagnostics
- Dell Embedded System Diagnostics
Jumpers and connectors
Technical specifications
Getting help

DELL R430 User Manual

Displayed below is the user manual for R430 by DELL which is a product in the Servers category. This manual has pages.

Related Manuals

DELL R430 Manual

Dell PowerEdge R430

Owner's Manual

Regulatory Model: E28S Series

Regulatory Type: E28S001

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your computer.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you

how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

intellectual property laws. Dell™ and the Dell logo are trademarks of Dell Inc. in the United States and/or other

jurisdictions. All other marks and names mentioned herein may be trademarks of their respective companies.

2015 - 12

Rev. A01

Contents

1 About your system................................................................................................ 8

Front-panel features and indicators.....................................................................................................8

LCD panel features..............................................................................................................................14

Home screen..................................................................................................................................15

Setup menu....................................................................................................................................15

View menu..................................................................................................................................... 15

Diagnostic indicators...........................................................................................................................16

Hot swappable hard drive indicator codes.........................................................................................17

Back-panel features and indicators....................................................................................................18

NIC indicator codes............................................................................................................................ 20

Indicator codes for redundant power supply unit.............................................................................20

Non-redundant power supply unit indicator codes..........................................................................22

Documentation matrix........................................................................................................................23

Quick Resource Locator (QRL)...........................................................................................................23

2 Performing initial system configuration ....................................................... 25

Setting up your system....................................................................................................................... 25

Setting up and configuring the iDRAC IP address ............................................................................ 25

Logging in to iDRAC............................................................................................................................25

Installing the operating system...........................................................................................................26

Managing your system remotely........................................................................................................26

Downloading and installing drivers and firmware............................................................................. 26

3 Pre-operating system management applications........................................28

Navigation keys................................................................................................................................... 28

About system setup.............................................................................................................................29

Entering System Setup.................................................................................................................. 29

System Setup Main Menu..............................................................................................................29

System BIOS screen details...........................................................................................................29

System Information screen details............................................................................................... 30

Memory Settings screen................................................................................................................31

Processor Settings screen............................................................................................................. 31

SATA Settings screen details......................................................................................................... 33

Boot Settings screen details..........................................................................................................36

Network Settings screen details....................................................................................................37

Integrated Devices screen details.................................................................................................37

Serial Communication screen details...........................................................................................39

System Profile Settings screen details..........................................................................................39

System Security Settings details....................................................................................................41

Miscellaneous Settings screen details.......................................................................................... 42

About Boot Manager...........................................................................................................................43

Entering Boot Manager ................................................................................................................ 43

Boot Manager main menu............................................................................................................ 43

About Dell Lifecycle Controller..........................................................................................................44

Changing the boot order....................................................................................................................44

Choosing the system boot mode...................................................................................................... 44

Assigning a system and setup password............................................................................................45

Using your system password to secure your system........................................................................ 45

Deleting or changing an existing system and/or setup password....................................................46

Operating with a setup password enabled........................................................................................ 46

Embedded system management........................................................................................................47

iDRAC Settings utility...........................................................................................................................47

Entering the iDRAC Settings utility................................................................................................47

Changing the Thermal Settings.................................................................................................... 47

4 Installing and removing system components...............................................49

Safety instructions...............................................................................................................................49

Before working inside your system....................................................................................................49

After working inside your system....................................................................................................... 50

Recommended tools.......................................................................................................................... 50

Front bezel (optional)..........................................................................................................................50

Installing the optional front bezel................................................................................................ 50

Removing the front bezel..............................................................................................................51

Removing and installing the system cover.........................................................................................51

Removing the system cover......................................................................................................... 52

Installing the system cover........................................................................................................... 53

Inside the system.................................................................................................................................53

Cooling shroud....................................................................................................................................55

Removing the cooling shroud...................................................................................................... 56

Installing the cooling shroud........................................................................................................ 57

System memory...................................................................................................................................57

General memory module installation guidelines.........................................................................59

Mode-specific guidelines..............................................................................................................59

Sample memory configurations...................................................................................................60

Removing memory module..........................................................................................................62

Installing memory modules.......................................................................................................... 63

Hard drives...........................................................................................................................................65

Removing a 2.5 inch hard-drive blank......................................................................................... 65

Installing a 2.5 inch hard-drive blank........................................................................................... 66

Removing a 3.5 inch hard-drive blank..........................................................................................67

Installing a 3.5 inch hard-drive blank........................................................................................... 68

Removing a cabled hard drive......................................................................................................68

Installing a cabled hard drive........................................................................................................69

Removing a hot-swap hard drive................................................................................................. 70

Installing a hot-swap hard drive....................................................................................................71

Installing a 2.5 inch hard drive into a 3.5 inch hard-drive adapter..............................................72

Removing a 2.5 inch hard drive from a 3.5 inch hard-drive adapter.......................................... 73

Installing a hard-drive adapter into a hard-drive carrier..............................................................73

Removing a hard-drive adapter from a hard-drive carrier.......................................................... 74

Removing a hard drive from a hard-drive carrier.........................................................................74

Installing a hard drive into a hard-drive carrier............................................................................ 75

Optical drive (optional)........................................................................................................................75

Removing an ultra slim optical drive.............................................................................................75

Installing an ultra slim optical drive.............................................................................................. 76

Removing the standard optical drive............................................................................................ 77

Installing the standard optical drive..............................................................................................78

Cooling fans........................................................................................................................................ 79

Removing a cooling fan................................................................................................................ 79

Installing a cooling fan..................................................................................................................80

Internal USB memory key (optional)...................................................................................................81

Replacing the internal USB key..................................................................................................... 81

Expansion cards and expansion-card risers (optional)......................................................................82

Expansion card installation guidelines......................................................................................... 82

Removing the expansion-card riser.............................................................................................84

Installing the expansion-card riser............................................................................................... 85

Removing an expansion card....................................................................................................... 85

Installing an expansion card......................................................................................................... 86

iDRAC ports card (optional)................................................................................................................ 87

Removing the iDRAC port card.................................................................................................... 87

Installing the iDRAC port card...................................................................................................... 89

SD vFlash media card..........................................................................................................................89

Replacing an SD vFlash media card..............................................................................................89

Internal dual SD module (optional).................................................................................................... 90

Removing an internal SD card......................................................................................................90

Installing an internal SD card.........................................................................................................91

Removing the optional internal dual SD module.........................................................................91

Installing the optional internal dual SD module ..........................................................................93

Integrated storage controller card..................................................................................................... 93

Removing the integrated storage controller card....................................................................... 93

Installing the integrated storage controller card......................................................................... 95

Heat sinks and processors.................................................................................................................. 95

Removing the heat sink................................................................................................................ 96

Removing a processor.................................................................................................................. 96

Installing a processor.................................................................................................................... 99

Installing the heat sink.................................................................................................................102

Power supplies.................................................................................................................................. 103

Hot spare feature........................................................................................................................ 104

Removing a redundant power supply........................................................................................ 104

Installing a redundant power supply.......................................................................................... 105

Removing a non-redundant power supply................................................................................106

Installing a non-redundant power supply..................................................................................107

Removing the power supply unit blank..................................................................................... 108

Installing the power supply unit blank....................................................................................... 108

System battery...................................................................................................................................108

Replacing the system battery..................................................................................................... 108

Hard-drive backplane........................................................................................................................110

Removing the hard-drive backplane.......................................................................................... 110

Installing the hard-drive backplane.............................................................................................117

Control-panel assembly.................................................................................................................... 117

Removing the control panel........................................................................................................117

Installing the control panel.........................................................................................................120

Removing the control-panel module......................................................................................... 121

Installing the control-panel module...........................................................................................124

Power interposer board.................................................................................................................... 125

Removing the power interposer board...................................................................................... 125

Installing the power interposer board........................................................................................ 126

System board.....................................................................................................................................127

Removing the system board....................................................................................................... 127

Installing the system board.........................................................................................................129

Trusted Platform Module...................................................................................................................131

Installing the Trusted Platform Module ......................................................................................131

Re-enabling the TPM for BitLocker users...................................................................................132

Re-enabling the TPM for TXT users............................................................................................132

5 Troubleshooting your system........................................................................ 133

Safety first—for you and your system...............................................................................................133

Troubleshooting system startup failure............................................................................................133

Troubleshooting external connections............................................................................................133

Troubleshooting the video subsystem............................................................................................. 133

Troubleshooting a USB device......................................................................................................... 133

Troubleshooting a serial I/O device................................................................................................. 134

Troubleshooting a NIC......................................................................................................................134

Troubleshooting a wet system......................................................................................................... 135

Troubleshooting a damaged system................................................................................................136

Troubleshooting the system battery................................................................................................ 136

Troubleshooting power supply units................................................................................................137

Power source problems....................................................................................................................137

Power supply unit problems............................................................................................................. 137

Troubleshooting cooling problems..................................................................................................138

Troubleshooting cooling fans.......................................................................................................... 138

Troubleshooting system memory.................................................................................................... 139

Troubleshooting an internal USB key...............................................................................................140

Troubleshooting an SD card.............................................................................................................140

Troubleshooting an optical drive......................................................................................................141

Troubleshooting a tape backup unit................................................................................................ 142

Troubleshooting a hard drive........................................................................................................... 142

Troubleshooting a storage controller.............................................................................................. 143

Troubleshooting expansion cards....................................................................................................144

Troubleshooting processors.............................................................................................................144

System messages.............................................................................................................................. 145

Warning messages.......................................................................................................................145

Diagnostic messages...................................................................................................................145

Alert messages.............................................................................................................................145

6 Using system diagnostics................................................................................146

Dell Embedded System Diagnostics.................................................................................................146

When to use the Embedded System Diagnostics......................................................................146

Running the Embedded System Diagnostics from Boot Manager........................................... 146

Running the Embedded System Diagnostics from the Dell Lifecycle Controller.................... 146

System diagnostic controls.........................................................................................................147

7 Jumpers and connectors................................................................................ 148

System board jumper settings..........................................................................................................148

System board connectors.................................................................................................................149

Disabling a forgotten password........................................................................................................ 151

8 Technical specifications..................................................................................152

9 Getting help.......................................................................................................158

Contacting Dell................................................................................................................................. 158

Locating your system Service Tag....................................................................................................158

Documentation feedback.................................................................................................................158

Quick Resource Locator (QRL).........................................................................................................158

About your system

The Dell PowerEdge R430 is a rack server that supports up to two processors based on the Intel Xeon EP

E5-2600 v3 family, up to 12 DIMMs, and up to ten hard drives or SSDs.

The R430 systems are available in the following configurations:

Table 1. System configurations

System Configuration

Four hard-drive

systems

Up to four 3.5-inch, cabled hard drives with non-redundant or redundant Power

Supply Unit (PSU)

Up to four 3.5-inch, hot-swappable hard drives with non-redundant or

redundant PSU

Eight hard-drive

systems

Up to eight 2.5-inch, hot-swappable hard drives or SSDs with redundant PSU

Ten hard-drive

systems

Up to ten 2.5-inch, hot-swappable hard drives or SSDs with redundant PSU

Front-panel features and indicators

Figure 1. Front-panel features and indicators—four 3.5 inch hot-swappable hard-drive chassis

Table 2. Front-panel features and indicators—four 3.5 inch hot-swappable hard-drive chassis

Item Indicator, Button, or

Connector Icon Description

1 Power-on indicator,

power button

The power-on indicator lights when the system

power is on. The power button controls the power

supply output to the system.

Item Indicator, Button, or

Connector Icon Description

NOTE: On ACPI-compliant operating systems,

turning off the system using the power button

causes the system to perform a graceful

shutdown before power to the system is

turned off.

2 NMI button Used to troubleshoot software and device driver

errors when running certain operating systems.

This button can be pressed using the end of a

paper clip.

Use this button only if directed to do so by

qualified support personnel or by the operating

system's documentation.

3 System identification

button

The identification buttons on the front and back

panels can be used to locate a particular system

within a rack. When one of these buttons is

pressed, the LCD panel on the front and the

system status indicator on the back flashes until

one of the buttons is pressed again.

Press to toggle the system ID on and off.

If the system stops responding during POST, press

and hold the system ID button for more than five

seconds to enter BIOS progress mode.

To reset iDRAC (if not disabled in F2 iDRAC setup)

press and hold the button for more than 15

seconds.

4 Video connector Allows you to connect a display to the system.

5 LCD menu buttons Allow you to navigate the control panel LCD menu.

6 LCD panel Displays system ID, status information, and system

error messages. See LCD panel features.

NOTE: LCD panel is not available in a cabled

hard-drive chassis.

7 USB management port/

iDRAC managed USB

port

The USB management port can function as a

regular USB port or provide access to the iDRAC

features. For more information, see the Integrated

Dell Remote Access Controller User’s Guide at

Dell.com/idracmanuals.

8 USB connector Allows you to connect USB devices to the system.

The port is USB 2.0-compliant.

Item Indicator, Button, or

Connector Icon Description

9 Information tag A slide-out label panel which contains system

information such as Service Tag, NIC, MAC

address, and so on for your reference.

10 Hard drives Up to four 3.5 inch hot-swappable hard drives or

SSDs.

11 Optical drive (optional) One optional slim SATA DVD-ROM drive or DVD

+/-RW drive.

Figure 2. Front-panel features and indicators—eight 2.5 inch hot-swappable hard-drives or SSDs chassis

Table 3. Front-panel features and indicators—eight 2.5 inch hot-swappable hard-drives or SSDs

Item Indicator, Button, or

Connector Icon Description

1 Power-on indicator,

power button

The power-on indicator lights when the system

power is on. The power button controls the power

supply output to the system.

NOTE: On ACPI-compliant operating systems,

turning off the system using the power button

causes the system to perform a graceful

shutdown before power to the system is

turned off.

2 NMI button Used to troubleshoot software and device driver

errors when running certain operating systems.

This button can be pressed using the end of a

paper clip.

Use this button only if directed to do so by

qualified support personnel or by the operating

system's documentation.

3 System identification

button

The identification buttons on the front and back

panels can be used to locate a particular system

within a rack. When one of these buttons is

pressed, the LCD panel on the front and the

system status indicator on the back flashes until

one of the buttons is pressed again.

Item Indicator, Button, or

Connector Icon Description

Press to toggle the system ID on and off.

If the system stops responding during POST, press

and hold the system ID button for more than five

seconds to enter BIOS progress mode.

To reset iDRAC (if not disabled in F2 iDRAC setup)

press and hold the button for more than 15

seconds.

4 USB management port

or iDRAC managed USB

port

The USB management port can function as a

regular USB port or provide access to the iDRAC

features. For more information, see the Integrated

Dell Remote Access Controller User’s Guide at

Dell.com/idracmanuals.

5 USB connector Allows you to connect USB devices to the system.

The port is USB 2.0-compliant.

6 Optical drive (optional) One optional slim SATA DVD-ROM drive or DVD

+/-RW drive.

7 LCD menu buttons Allow you to navigate the control panel LCD menu.

8 Information tag A slide-out label panel which contains system

information such as Service Tag, NIC, MAC

address, and so on for your reference.

9 LCD panel Displays system ID, status information, and system

error messages. See LCD panel features.

10 Video connector Allows you to connect a VGA display to the system.

11 Hard drives Up to eight 2.5-inch hot-swappable hard drives or

SSDs.

Figure 3. Front-panel features and indicators—ten 2.5-inch hot-swappable hard-drives or SSDs chassis

Table 4. Front-panel features and indicators—ten 2.5-inch hot-swappable hard-drives or SSDs

Item Indicator, Button, or

Connector Icon Description

1 USB management port/

iDRAC managed USB

port

The USB management port can function as a

regular USB port or provide access to the iDRAC

features. For more information, see the Integrated

Dell Remote Access Controller User’s Guide at

Dell.com/idracmanuals.

2 Diagnostic indicator The diagnostic indicator lights up to display error

status. For more information, see Diagnostic

indicators.

3 Power-on indicator,

power button

The power-on indicator lights when the system

power is on. The power button controls the power

supply output to the system.

NOTE: On ACPI-compliant operating systems,

turning off the system using the power button

causes the system to perform a graceful

shutdown before power to the system is

turned off.

4 NMI button Used to troubleshoot software and device driver

errors when running certain operating systems.

This button can be pressed using the end of a

paper clip.

Use this button only if directed to do so by

qualified support personnel or by the operating

system's documentation.

5 System identification

button

The identification buttons on the front and back

panels can be used to locate a particular system

within a rack. When one of these buttons is

pressed, the LCD panel on the front and the

system status indicator on the back flashes until

one of the buttons is pressed again.

Press to toggle the system ID on and off.

If the system stops responding during POST, press

and hold the system ID button for more than five

seconds to enter BIOS progress mode.

To reset iDRAC (if not disabled in F2 iDRAC setup)

press and hold the button for more than 15

seconds.

6 Hard drives Up to ten 2.5 inch hot-swappable hard drives/

SSDs.

Figure 4. Front-panel features and indicators—four 3.5 inch cabled hard-drive chassis

Table 5. Front panel features and indicators of four 3.5-inch cabled hard-drive

Item Indicator, Button, or

Connector Icon Description

1 Power-on indicator,

power button

The power-on indicator lights when the system

power is on. The power button controls the power

supply output to the system.

NOTE: On ACPI-compliant operating systems,

turning off the system using the power button

causes the system to perform a graceful

shutdown before power to the system is

turned off.

2 NMI button Used to troubleshoot software and device driver

errors when running certain operating systems.

This button can be pressed using the end of a

paper clip.

Use this button only if directed to do so by

qualified support personnel or by the operating

system's documentation.

3 System identification

button

The identification buttons on the front and back

panels can be used to locate a particular system

within a rack. When one of these buttons is

pressed, the system status indicator on the back

flashes until one of the buttons is pressed again.

Press to toggle the system ID on and off. If the

system stops responding during POST, press and

hold the system ID button for more than five

seconds to enter BIOS progress mode.

To reset the iDRAC (if not disabled in F2 iDRAC

setup) press and hold the button for more than 15

seconds.

4 Video connector Allows you to connect a display to the system.

Item Indicator, Button, or

Connector Icon Description

5 Diagnostic indicators The diagnostic indicator lights up to display error

status. For more information, see Diagnostic

indicators.

6 USB connectors (2) Allow you to connect USB devices to the system.

The ports are USB 2.0-compliant.

7 Information tag A slide-out label panel which contains system

information such as Service Tag, NIC, MAC

address, and so on for your reference.

8 Hard drives Up to four 3.5 inch cabled hard drives.

9 Optical drive (optional) One optional slim SATA DVD-ROM drive or DVD

+/-RW drive.

LCD panel features

The system's LCD panel provides system information and status and error messages to indicate if the

system is operating correctly or if the system needs attention. For more information on error messages,

see the Dell Event and Error Messages Reference Guide at Dell.com/openmanagemanuals

>OpenManage software.

• The LCD backlight lights blue during normal operating conditions.

• When the system needs attention, the LCD lights amber, and displays an error code followed by

descriptive text.

NOTE: If the system is connected to a power source and an error is detected, the LCD lights

amber regardless of whether the system is turned on or off.

• The LCD backlight turns OFF when the system is in standby mode and can be turned on by pressing

either the Select, Left, or Right button on the LCD panel.

• The LCD backlight remains OFF if LCD messaging is turned off through the iDRAC utility, the LCD

panel, or other tools.

Figure 5. LCD panel features

Table 6. LCD panel features

Item Button Description

1 Left Moves the cursor back in one-step increments.

2 Select Selects the menu item highlighted by the cursor.

Item Button Description

3 Right Moves the cursor forward in one-step increments.

During message scrolling:

• Press once to increase scrolling speed

• Press again to stop

• Press again to return to the default scrolling speed

• Press again to repeat the cycle

Home screen

The Home screen displays user-configurable information about the system. This screen is displayed

during normal system operation when there are no status messages or errors. When the system is in

standby mode, the LCD backlight turns off after five minutes of inactivity if there are no error messages.

Press one of the three navigation buttons (Select, Left, or Right) to view the Home screen.

To navigate to the Home screen from another menu, complete the following steps:

1. Press and hold the up arrow until the Home icon is displayed.

2. Select the Home icon.

3. From the Home screen, press the Select button to enter the main menu.

Setup menu

NOTE: When you select an option in the Setup menu, you must confirm the option before

proceeding to the next action.

Option Description

iDRAC Select DHCP or Static IP to configure the network mode. If Static IP is selected,

the available fields are IP, Subnet (Sub), and Gateway (Gtw). Select Setup DNS to

enable DNS and to view domain addresses. Two separate DNS entries are available.

Set error Select SEL to view LCD error messages in a format that matches the IPMI

description in the SEL. This is useful when trying to match an LCD message with an

SEL entry.

Select Simple to view LCD error messages in a simplified user-friendly description.

For more information about error messages, see the Dell Event and Error Messages

Reference Guide at Dell.com/openmanagemanuals > OpenManage software.

Set home Select the default information to be displayed on the Home screen. See View menu

for the options and option items that can be set as the default on the Home

screen.

View menu

NOTE: When you select an option in the View menu, you must confirm the option before

proceeding to the next action.

Option Description

iDRAC IP Displays the IPv4 or IPv6 addresses for iDRAC8. Addresses include DNS (Primary

and Secondary), Gateway, IP, and Subnet (IPv6 does not have Subnet).

MAC Displays the MAC addresses for iDRAC, iSCSI, or Network devices.

Name Displays the name of the Host, Model, or User String for the system.

Number Displays the Asset tag or the Service tag for the system.

Power Displays the power output of the system in BTU/hr or Watts. The display format can

be configured in the Set home submenu of the Setup menu.

Temperature Displays the temperature of the system in Celsius or Fahrenheit. The display format

can be configured in the Set home submenu of the Setup menu.

Diagnostic indicators

The diagnostic indicators on the system front panel display error status during system startup.

NOTE: The diagnostic indicators are not present if the system is equipped with an LCD display.

NOTE: No diagnostic indicators are lit when the system is turned off. To start the system, plug it into

a working power source and press the power button.

Table 7. Diagnostic indicators

Icon Description Condition Corrective action

Health

indicator

If the system is turned on

and in good health, the

indicator turns solid blue.

None required.

The indicator flashes amber

if the system is turned on or

in standby, and if any error

exists (for example, a failed

fan or hard drive).

Check the System Event Log or system

messages for the specific issue. For more

information about error messages, see the

Dell Event and Error Messages Reference

Guide at Dell.com/openmanagemanuals >

OpenManage software.

Invalid memory configurations can cause

the system to halt at startup without any

video output. See Getting help.

Hard drive

indicator

The indicator flashes amber

if there is a hard drive error.

Check the System Event Log to determine

the hard drive that has an error. Run the

appropriate Online Diagnostics test. Restart

the system and run embedded diagnostics

(ePSA). If the hard drives are configured in a

RAID array, restart the system and enter the

host adapter configuration utility program.

Electrical

indicator

The indicator flashes amber

if the system experiences an

electrical error (for example,

Check the System Event Log or system

messages for the specific issue. If it is due

to a problem with the PSU, check the LED

Icon Description Condition Corrective action

voltage out of range, or a

failed power supply unit

(PSU) or voltage regulator).

on the PSU. Reseat the PSU. If the problem

persists, see Getting help.

Temperature

indicator

The indicator flashes amber

if the system experiences a

thermal error (for example, a

temperature out of range or

fan failure).

Ensure that none of the following

conditions exist:

• A cooling fan has been removed or has

failed.

• System cover, cooling shroud, EMI filler

panel, memory module blank, or back

filler bracket is removed.

• Ambient temperature is too high.

• External airflow is obstructed.

See Getting help.

Memory

indicator

The indicator flashes amber

if a memory error occurs.

Check the system event log or system

messages for the location of the failed

memory. Reseat the memory module. If

the problem persists, see Getting help.

PCIe indicator The indicator flashes amber

if a PCIe card experiences

an error.

Restart the system. Update any required

drivers for the PCIe card. Reinstall the card.

If the problem persists, see Getting help.

Hot swappable hard drive indicator codes

Figure 6. Hot swappable hard drive indicators

1. hard drive activity indicator 2. hard drive status indicator

3. hard drive

NOTE: If the hard drive is in Advanced Host Controller Interface (AHCI) mode, the status indicator

(on the right side) does not function and remains OFF.

Table 8. Hot swappable hard drive indicators

Drive-status indicator pattern (RAID only) Condition

Flashes green two times per second Identifying drive or preparing for removal.

OFF Drive ready for insertion or removal.

NOTE: The drive status indicator remains OFF

until all hard drives are initialized after the system

is turned on. Drives are not ready for insertion or

removal during this time.

Flashes green, amber, and turns off Predicted drive failure

Flashes amber four times per second Drive failed

Flashes green slowly Drive rebuilding

Turns green Drive online

Flashes green three seconds, amber three

seconds, and turns off six seconds

Rebuild stopped

Back-panel features and indicators

Figure 7. Back-panel features and indicators

Table 9. Back-panel features and indicators

Item Indicator, Button, or

Connector Icon Description

1 Serial connector Allows you to connect a serial device to the

system.

2 Ethernet connector 1 Integrated 10/100/1000 Mbps NIC connector.

Item Indicator, Button, or

Connector Icon Description

3 vFlash card slot

(optional)

Allows you to connect the vFlash card.

4 iDRAC port (optional) Dedicated management port on the iDRAC ports

card.

5 PCIe expansion card

slots (2)

Allows you to connect a PCI Express expansion

card.

6 Video connector Allows you to connect a VGA display to the system.

7 Ethernet connector 2 Integrated 10/100/1000 Mbps NIC connector.

8 USB connector Allow you to connect USB devices to the system.

The port is USB 2.0-compliant.

9 USB connector Allow you to connect USB devices to the system.

The port is USB 3.0-compliant.

10 System identification

button

The identification buttons on the front and back

panels can be used to locate a particular system

within a rack. When one of these buttons is

pressed, the system status indicator on the back

flashes until one of the buttons is pressed again.

Press to toggle the system ID on and off. If the

system stops responding during POST, press and

hold the system ID button for more than five

seconds to enter BIOS progress mode.

To reset the iDRAC (if not disabled in F2 iDRAC

setup) press and hold the button for more than 15

seconds.

11 System identification

connector

Connects the optional system status indicator

assembly through the optional cable management

arm.

12 Ethernet connector 3 10/100/1000 Mbps NIC connector.

13 Ethernet connector 4

14 Power supply unit (PSU1

and PSU2) Redundant power

supply

Up to two 550 W redundant

AC power supplies.

Non-redundant

power supply

One 450 W non-redundant

AC power supply.

NOTE: Non-redundant

power supply is

supported in systems

with cabled hard drives

and the systems with x4

backplane.

Item Indicator, Button, or

Connector Icon Description

NOTE: For non-

redundant power supply

units, there is only one

power supply socket.

NIC indicator codes

Figure 8. NIC indicators

1. link indicator 2. activity indicator

Table 10. NIC indicators

Convention Indicator pattern Description

A Link and activity indicators

are OFF

The NIC is not connected to the network.

B Link indicator is green The NIC is connected to a valid network at its maximum

port speed (1 Gbps).

C Link indicator is yellow The NIC is connected to a valid network at less than its

maximum port speed.

D Activity indicator is flashing

green

Network data is being sent or received.

Indicator codes for redundant power supply unit

Each AC power supply unit (PSU) has an illuminated translucent handle that indicates whether power is

present or whether a power fault has occurred.

Figure 9. AC PSU status indicator

1. AC PSU status indicator or handle

Table 11. Redundant AC PSU status indicator

Convention Power Indicator

Pattern Condition

A Green A valid power source is connected to the PSU and the PSU is

operational.

B Flashing green When the PSU firmware is being updated, the PSU handle flashes

green.

CAUTION: Do not disconnect the power cord or unplug the

PSU when updating firmware. If firmware update is

interrupted, the PSUs will not function. You must roll back the

PSU firmware by using Dell Lifecycle Controller. For more

information, see Dell Lifecycle Controller User’s Guide at

Dell.com/idracmanuals.

C Flashing green

and turns off

When hot-adding a PSU, the PSU handle flashes green five times at

4 Hz rate and turns off. This indicates that there is a PSU mismatch

with respect to efficiency, feature set, health status, and supported

voltage. Ensure that both the PSUs are the same.

NOTE: For AC PSUs, use only PSUs with the Extended Power

Performance (EPP) label on the back. Mixing PSUs from

previous generations of Dell PowerEdge servers can result in a

PSU mismatch condition or failure to turn on.

D Flashing amber Indicates a problem in the PSU.

Convention Power Indicator

Pattern Condition

CAUTION: When correcting a PSU mismatch, replace only the

PSU with the flashing indicator. Swapping the other PSU to

make a matched pair can result in an error condition and

unexpected system shutdown. To change from a High Output

configuration to a Low Output configuration or vice versa,

you must turn off the system.

CAUTION: AC PSUs support both 220 V and 110 V input

voltages with the exception of Titanium PSUs, which support

only 220 V. When two identical PSUs receive different input

voltages, they can output different wattages, and trigger a

mismatch.

CAUTION: If two PSUs are used, they must be of the same type

and have the same maximum output power.

CAUTION: Combining AC and DC PSUs is not supported and

triggers a mismatch.

E Not lit Power is not connected.

Non-redundant power supply unit indicator codes

Press the self-diagnostic button to perform a quick health check on the non-redundant power supply

unit (PSU) of the system.

Figure 10. Non-redundant AC PSU status indicator and self-diagnostic button

1. self-diagnostic button 2. AC power supply unit status indicator

Table 12. Non-redundant AC PSU status indicator

Power Indicator Pattern Condition

Not lit Power is not connected or PSU is faulty.

Green A valid power source is connected to the PSU and the PSU is operational.

Documentation matrix

The documentation matrix provides information on documents that you can refer to for setting up and

managing your system.

Table 13. Documentation matrix

To... See the...

Install your system into a rack Rack documentation included with your rack

solution

Set up your system and know the system technical

specifications

Getting Started With Your System that shipped with

your system or see Dell.com/poweredgemanuals

Install the operating system Operating system documentation at Dell.com/

operatingsystemmanuals

Get an overview of the Dell Systems Management

offerings

Dell OpenManage Systems Management Overview

Guide at Dell.com/openmanagemanuals >

OpenManage software

Configure and log in to iDRAC, set up managed

and management system, know the iDRAC

features, and troubleshoot by using iDRAC

Integrated Dell Remote Access Controller User's

Guide at Dell.com/idracmanuals

Know about the RACADM subcommands and

supported RACADM interfaces

RACADM Command Line Reference Guide for

iDRAC at Dell.com/idracmanuals

Launch, enable, and disable Dell Lifecycle

Controller, know the features, use and

troubleshoot Dell Lifecycle Controller

Dell Lifecycle Controller User’s Guide at Dell.com/

idracmanuals

Use Dell Lifecycle Controller Remote Services Dell Lifecycle Controller Remote Services Quick

Start Guide at Dell.com/idracmanuals

Set up, use, and troubleshoot OpenManage Server

Administrator

Dell OpenManage Server Administrator User’s

Guide at Dell.com/openmanagemanuals >

OpenManage Server Administrator

Install, use, and troubleshoot OpenManage

Essentials

Dell OpenManage Essentials User’s Guide at

Dell.com/openmanagemanuals > OpenManage

Essentials

Know the features of the storage controller cards,

deploy the cards, and manage the storage

subsystem

Storage controller documentation at Dell.com/

storagecontrollermanuals

Check the event and error messages generated by

the system firmware and agents that monitor

system components

Dell Event and Error Messages Reference Guide at

Dell.com/openmanagemanuals > OpenManage

software

Quick Resource Locator (QRL)

Use the Quick Resource Locator (QRL) to get immediate access to system information and how-to

videos. This can be done by visiting dell.com/QRL or by using your smartphone or tablet and a model

specific Quick Resource (QR) code located on your Dell PowerEdge system. To try out the QR code, scan

the following image.

Figure 11. Quick Resource Locator

Performing initial system configuration

After you receive your PowerEdge system, you must set up your system, install the operating system if it

is not pre-installed, and set up and configure the system iDRAC IP address.

Setting up your system

1. Unpack the server.

2. Install the server into the rack. For more information on installing the server into the rack, see your

system Rack Installation Placemat at dell.com/poweredgemanuals.

3. Connect the peripherals to the system.

4. Connect the system to its electrical outlet.

5. Turn the system on by pressing the power button or using iDRAC.

6. Turn on the attached peripherals.

Setting up and configuring the iDRAC IP address

You can set up the Integrated Dell Remote Access Controller (iDRAC) IP address by using one of the

following interfaces:

• iDRAC Settings utility

• Lifecycle Controller

• Dell OpenManage Deployment Toolkit

• Server LCD panel

You can configure iDRAC IP address by using the following interfaces:

• iDRAC Web interface. For more information, see the Integrated Dell Remote Access Controller User's

Guide.

• Remote Access Controller ADMin (RACADM). For more information, see the RACADM Command Line

Interface Reference Guide and the Integrated Dell Remote Access Controller User's Guide.

• Remote Services that includes Web Services Management (WS-Man). For more information, see the

Lifecycle Controller Remote Services Quick Start Guide.

For more information on setting up and configuring iDRAC, see the Integrated Dell Remote Access

Controller User's Guide at dell.com/esmmanuals.

Logging in to iDRAC

You can log in to iDRAC as an iDRAC local user, a Microsoft Active Directory user, or a Lightweight

Directory Access Protocol (LDAP) user. You can also log in by using Single Sign-On or a Smart Card. The

default user name is root and password is calvin. For more information on logging in to iDRAC and

iDRAC licenses, see the Integrated Dell Remote Access Controller User's Guide at dell.com/esmmanuals.

You can also access iDRAC using RACADM. For more information, see the RACADM Command Line

Interface Reference Guide and the Integrated Dell Remote Access Controller User's Guide available at

dell.com/esmmanuals.

Installing the operating system

If the server is shipped without an operating system, install the supported operating system on the server

by using one of the following methods:

• Dell Systems Management Tools and Documentation media. See the operating system

documentation at dell.com/operatingsystemmanuals.

• Dell Lifecycle Controller. See the Lifecycle Controller documentation at dell.com/esmmanuals.

• Dell OpenManage Deployment Toolkit. See the OpenManage documentation at dell.com/

openmanagemanuals.

For information on the list of operating systems supported on your system, see the operating systems

support matrix at dell.com/ossupport.

Managing your system remotely

To perform out-of-band systems management using iDRAC, you must configure iDRAC for remote

accessibility, set up the management station and managed system, and configure the supported Web

browsers. For more information, see the Integrated Dell Remote Access Controller User’s Guide at

dell.com/esmmanuals.

You can also remotely monitor and manage the server by using the Dell OpenManage Server

Administrator (OMSA) software and OpenManage Essentials (OME) systems management console. For

more information, see dell.com/openmanagemanuals.

Downloading and installing drivers and firmware

It is recommended that you download and install the latest BIOS, drivers, and systems management

firmware on your system.

Prerequisites

Ensure that you clear the web browser cache.

Steps

1. Go to dell.com/support/drivers.

2. In the Product Selection section, enter the Service Tag of your system in the Service Tag or Express

Service Code field.

NOTE: If you do not have the Service Tag, select Automatically detect my Service Tag for me

to allow the system to automatically detect your Service Tag, or select Choose from a list of all

Dell products to select your product from the Product Selection page.

3. Click Get drivers and downloads.

The drivers that are applicable to your selection are displayed.

4. Download the drivers you require to a diskette drive, USB drive, CD, or DVD.

Pre-operating system management

applications

The pre-operating system management applications for your PowerEdge system help you manage

different settings and features of your system without booting to the operating system.

Your PowerEdge system has the following pre-operating system management applications:

• System Setup

• Boot Manager

• Dell Lifecycle Controller

Navigation keys

The navigation keys can help you quickly access the pre-operating system management applications.

Key Description

F2 Enables you to enter System Setup.

F10 Enables you to enter system services and starts Lifecycle Controller.

F11 Enables you to enter Boot Manager.

F12 Enables you to enter PXE Boot.

Page Up Enables you to move to the previous screen.

Page Down Enables you to move to the next screen.

Up arrow Enables you to move to the previous field.

Down arrow Enables you to move to the next field.

Enter Enables you to type a value in the selected field (if applicable).

Spacebar Enables you to expand or collapse a drop-down list, if applicable.

Tab Enables you to move to the next menu item.

NOTE: This feature is applicable only for the standard graphic browser.

Esc Enables you to move to the previous page until you view the main screen. Pressing

Esc in the main screen exits System BIOS, iDRAC Settings, Device Settings, or

Service Tag Settings, and proceeds with system boot.

F1 Displays the system setup help.

About system setup

By using the System Setup screen, you can configure the BIOS settings, iDRAC settings, and device

settings of your system.

NOTE: Help text for the selected field is displayed in the graphical browser by default. To view the

help text in the text browser, press F1.

You can access system setup in two ways:

• Standard graphical browser—The browser is enabled by default.

• Text Browser—The browser is enabled by using Console Redirection.

Entering System Setup

1. Turn on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

If your operating system begins to load before you press F2, wait for the system to finish booting,

and then restart your system and try again.

System Setup Main Menu

The System Setup Main Menu screen details are explained as follows:

Option Description

System BIOS Enables you to configure BIOS settings.

iDRAC Settings Enables you to configure iDRAC settings.

The iDRAC settings utility is an interface to set up and configure the iDRAC

parameters by using UEFI. You can enable or disable various iDRAC parameters by

using the iDRAC settings utility. For more information about this utility, see

Integrated Dell Remote Access Controller User’s Guide at Dell.com/idracmanuals.

Device Settings Enables you to configure device settings.

System BIOS screen details

You can use the System BIOS screen to edit specific functions such as boot order, system password,

setup password, set the RAID mode, and enable or disable USB ports.

To view the System BIOS screen, click System Setup Main Menu → System BIOS.

The System BIOS screen details are explained as follows:

Option Description

System

Information

Displays information about the system such as the system model name, BIOS

version, and Service Tag.

Memory Settings Displays information and options related to the installed memory.

Option Description

Processor Settings Displays information and options related to the processor such as speed, cache

size.

SATA Settings Displays options to enable or disable the integrated SATA controller and ports.

Boot Settings Displays options to specify the boot mode (BIOS or UEFI). Enables you to modify

UEFI and BIOS boot settings.

Network Settings Displays options to change the network settings.

Integrated

Devices

Displays options to manage integrated device controllers and ports and specify

related features and options.

Serial

Communication

Displays options to manage the serial ports and specify related features and

options.

System Profile

Settings

Displays options to change the processor power management settings, memory

frequency, and so on.

System Security Displays options to configure the system security settings, such as system

password, setup password, Trusted Platform Module (TPM) security. It also

manages the power and NMI buttons on the system.

Miscellaneous

Settings

Displays options to change the system date, time, and so on.

System Information screen details

You can use the System Information screen to view system properties such as Service Tag, system model

name, and the BIOS version.

To view the System Information screen, click System Setup Main Menu → System BIOS → System

Information.

The System Information screen details are explained as follows:

Option Description

System Model

Name

Displays the system model name.

System BIOS

Version

Displays the BIOS version installed on the system.

System

Management

Engine Version

Displays the current version of the Management Engine firmware.

System Service

Tag

Displays the system Service Tag.

System

Manufacturer

Displays the name of the system manufacturer.

System

Manufacturer

Contact

Information

Displays the contact information of the system manufacturer.

System CPLD

Version

Displays the current version of the system complex programmable logic device

(CPLD) firmware.

Option Description

UEFI Compliance

Version

Displays the UEFI compliance level of the system firmware.

Memory Settings screen

You can use the Memory Settings screen to view all the memory settings as well as enable or disable

specific memory functions such as system memory testing and node interleaving.

To view the Memory Setting screen, click System Setup Main Menu → System BIOS → Memory Settings.

Option Description

System Memory

Size

Displays the amount of memory installed in the system.

System Memory

Type

Displays the type of memory installed in the system.

System Memory

Speed

Displays the system memory speed.

System Memory

Voltage

Displays the system memory voltage.

Video Memory Displays the amount of video memory utilized.

System Memory

Testing

Specifies whether system memory tests are run during system boot. Options are

Enabled and Disabled. By default, the System Memory Testing option is set to

Disabled.

Memory

Operating Mode Specifies the memory operating mode. The options available are Optimizer Mode,

Advanced ECC Mode, Mirror Mode, Spare Mode, and Spare with Advanced ECC

Mode. By default, the Memory Operating Mode option is set to Optimizer Mode.

NOTE: The Memory Operating Mode can have different defaults and available

options based on the memory configuration of your system.

Node Interleaving Specifies if Non-Uniform Memory architecture (NUMA) is supported. If this field is

Enabled, memory interleaving is supported if a symmetric memory configuration is

installed. If Disabled, the system supports NUMA (asymmetric) memory

configurations. By default, Node Interleaving option is set to Disabled.

Snoop Mode Specifies the Snoop Mode options. Snoop Mode options available are Home

Snoop, Early Snoop, and Cluster on Die. By default, the Snoop Mode option is set

to Early Snoop. The field is only available when Node Interleaving is Disabled.

Processor Settings screen

You can use the Processor Settings screen to view the processor settings and perform specific functions

such as enabling virtualization technology, hardware prefetcher, and logical processor idling.

To view the Processor Settings screen, click System Setup Main Menu → System BIOS → Processor

Settings.

Option Description

Logical Processor Enables or disables the logical processors and displays the number of logical

processors. If the Logical Processor option is set to Enabled, the BIOS displays all

the logical processors. If this option is set to Disabled, the BIOS displays only one

Option Description

logical processor per core. By default, the Logical Processor option is set to

Enabled.

Alternate RTID

(Requestor

Transaction ID)

Setting

Enables you to allocate more RTIDs to the remote socket, thereby increasing

cache performance between the sockets or easing work in normal mode for

NUMA. By default, the Alternate RTID (Requestor Transaction ID) Setting is set to

Disabled.

Virtualization

Technology

Enables or disables the additional hardware capabilities provided for virtualization.

By default, the Virtualization Technology option is set to Enabled.

Address

Translation

Service (ATS)

Defines the Address Translation Cache (ATC) for devices to cache the DMA

transactions. This field provides an interface to a chipset's Address Translation and

Protection Table to translate DMA addresses to host addresses. By default, the

option is set to Enabled.

Adjacent Cache

Line Prefetch

Optimizes the system for applications that require high utilization of sequential

memory access. By default, the Adjacent Cache Line Prefetch option is set to

Enabled. You can disable this option for applications that require high utilization of

random memory access.

Hardware

Prefetcher

Enables or disables the hardware prefetcher. By default, the Hardware Prefetcher

option is set to Enabled.

DCU Streamer

Prefetcher

Allows you to enable or disable the Data Cache Unit (DCU) streamer prefetcher. By

default, the DCU Streamer Prefetcher option is set to Enabled.

DCU IP Prefetcher Enables or disables the Data Cache Unit (DCU) IP prefetcher. By default, the DCU

IP Prefetcher option is set to Enabled.

Execute Disable Enables or disables the execute disable memory protection technology. By default,

the Execute Disable option is set to Enabled.

Logical Processor

Idling

Enables or disables the operating system capability to put logical processors in the

idling state in order to reduce power consumption. By default, the option is set to

Disabled.

Configurable TDP Allows reconfiguration of Thermal Design Power (TDP) to lower levels.

TDP refers to the maximum amount of power the cooling system is required to

dissipate.

X2Apic Mode Enables or disables the X2Apic mode.

Number of Cores

per Processor

Controls the number of enabled cores in each processor. By default, the Number

of Cores per Processor option is set to All.

Hardware

Prefetcher

Enables or disables the hardware prefetcher. By default, the Hardware Prefetcher

option is set to Enabled.

DCU Streamer

Prefetcher

Allows you to enable or disable the Data Cache Unit (DCU) streamer prefetcher. By

default, the DCU Streamer Prefetcher option is set to Enabled.

DCU IP Prefetcher Enables or disables the Data Cache Unit (DCU) IP prefetcher. By default, the DCU

IP Prefetcher option is set to Enabled.

Execute Disable Enables or disables the execute disable memory protection technology. By default,

the Execute Disable option is set to Enabled.

Option Description

Logical Processor

Idling

Enables or disables the operating system capability to put logical processors in the

idling state in order to reduce power consumption. By default, the option is set to

Disabled.

Configurable TDP Allows reconfiguration of Thermal Design Power (TDP) to lower levels.

TDP refers to the maximum amount of power the cooling system is required to

dissipate.

X2Apic Mode Enables or disables the X2Apic mode.

Number of Cores

per Processor

Controls the number of enabled cores in each processor. By default, the Number

of Cores per Processor option is set to All.

Processor 64-bit

Support

Specifies if the processor(s) support 64-bit extensions.

Processor Core

Speed

Displays the maximum core frequency of the processor.

Processor Bus

Speed

Displays the bus speed of the processor.

NOTE: The processor bus speed option displays only when both processors

are installed.

Processor 1 NOTE: Depending on the number of installed CPUs, there may be up to two

processor listings. The following settings are displayed for each processor

installed in the system.

Family-Model-

Stepping

Displays the family, model and stepping of the processor as defined by Intel.

Brand Displays the brand name reported by the processor.

Level 2 Cache Displays the total L2 cache.

Level 3 Cache Displays the total L3 cache.

Number of Cores Displays the number of cores per processor.

SATA Settings screen details

You can use the SATA Settings screen to view the SATA settings of SATA devices and enable RAID on

your system.

To view the SATA Settings screen, click System Setup Main Menu → System BIOS → SATA Settings.

The SATA Settings screen details are explained as follows:

Option Description

Embedded SATA Enables the embedded SATA option to be set to Off, ATAAHCI, or RAID modes.

This option is set to AHCI by default.

Security Freeze

Lock

Sends Security Freeze Lock command to the Embedded SATA drives during POST.

This option is applicable only for ATA and AHCI modes.

Write Cache Enables or disables the command for Embedded SATA drives during POST.

Option Description

Port A Sets the drive type of the selected device. For Embedded SATA settings in ATA

mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS

support.

For AHCI or RAID mode, BIOS support is always enabled.

Option Description

Model Displays the drive model of the selected device.

Drive Type Displays the type of drive attached to the SATA port.

Capacity Displays the total capacity of the hard drive. This field is

undefined for removable media devices such as optical

drives.

Port B Sets the drive type of the selected device. For Embedded SATA settings in ATA

mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS

support.

For AHCI or RAID mode, BIOS support is always enabled.

Option Description

Model Displays the drive model of the selected device.

Drive Type Displays the type of drive attached to the SATA port.

Capacity Displays the total capacity of the hard drive. This field is

undefined for removable media devices such as optical

drives.

Port C Sets the drive type of the selected device. For Embedded SATA settings in ATA

mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS

support.

For AHCI or RAID mode, BIOS support is always enabled.

Option Description

Model Displays the drive model of the selected device.

Drive Type Displays the type of drive attached to the SATA port.

Capacity Displays the total capacity of the hard drive. This field is

undefined for removable media devices such as optical

drives.

Port D Sets the drive type of the selected device. For Embedded SATA settings in ATA

mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS

support.

For AHCI or RAID mode, BIOS support is always enabled.

Option Description

Model Displays the drive model of the selected device.

Drive Type Displays the type of drive attached to the SATA port.

Option Description

Capacity Displays the total capacity of the hard drive. This field is

undefined for removable media devices such as optical

drives.

Port E Sets the drive type of the selected device. For Embedded SATA settings in ATA

mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS

support.

For AHCI or RAID mode, BIOS support is always enabled.

Option Description

Model Displays the drive model of the selected device.

Drive Type Displays the type of drive attached to the SATA port.

Capacity Displays the total capacity of the hard drive. This field is

undefined for removable media devices such as optical

drives.

Port F Sets the drive type of the selected device. For Embedded SATA settings in ATA

mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS

support.

For AHCI or RAID mode, BIOS support is always enabled.

Option Description

Model Displays the drive model of the selected device.

Drive Type Displays the type of drive attached to the SATA port.

Capacity Displays the total capacity of the hard drive. This field is

undefined for removable media devices such as optical

drives.

Port G Sets the drive type of the selected device. For Embedded SATA settings in ATA

mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS

support.

For AHCI or RAID mode, BIOS support is always enabled.

Option Description

Model Displays the drive model of the selected device.

Drive Type Displays the type of drive attached to the SATA port.

Capacity Displays the total capacity of the hard drive. This field is

undefined for removable media devices such as optical

drives.

Port H Sets the drive type of the selected device. For Embedded SATA settings in ATA

mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS

support.

Option Description

For AHCI or RAID mode, BIOS support is always enabled.

Option Description

Model Displays the drive model of the selected device.

Drive Type Displays the type of drive attached to the SATA port.

Capacity Displays the total capacity of the hard drive. This field is

undefined for removable media devices such as optical

drives.

Port I Sets the drive type of the selected device. For Embedded SATA settings in ATA

mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS

support.

For AHCI or RAID mode, BIOS support is always enabled.

Option Description

Model Displays the drive model of the selected device.

Drive Type Displays the type of drive attached to the SATA port.

Capacity Displays the total capacity of the hard drive. This field is

undefined for removable media devices such as optical

drives.

Port J Sets the drive type of the selected device. For Embedded SATA settings in ATA

mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS

support.

For AHCI or RAID mode, BIOS support is always enabled.

Option Description

Model Displays the drive model of the selected device.

Drive Type Displays the type of drive attached to the SATA port.

Capacity Displays the total capacity of the hard drive. This field is

undefined for removable media devices such as optical

drives.

Boot Settings screen details

You can use the Boot Settings screen to set the boot mode to either BIOS or UEFI. It also enables you to

specify the boot order.

To view the Boot Settings screen, click System Setup Main Menu → System BIOS → Boot Settings.

The Boot Settings screen details are explained as follows:

Option Description

Boot Mode Enables you to set the boot mode of the system. Setting this field to UEFI disables

the BIOS Boot Settings menu. Setting this field to BIOS disables the UEFI Boot

Settings menu.

Option Description

CAUTION: Switching the boot mode may prevent the system from booting if

the operating system is not installed in the same boot mode.

If the operating system supports UEFI, you can set this option to UEFI. Setting this

field to BIOS allows compatibility with non-UEFI operating systems. This option is

set to BIOS by default.

Boot Sequence

Retry

Enables or disables the Boot Sequence Retry feature. If this field is enabled and the

system fails to boot, the system reattempts the boot sequence after 30 seconds.

This option is set to Enabled by default.

Hard-Disk Failover Specifies the hard drive that is booted in the event of a hard drive failure. The

devices are selected in the Hard-Disk Drive Sequence on the Boot Option Setting

menu. When this option is set to Disabled, only the first hard drive in the list is

attempted to boot. When this option is set to Enabled, all hard drives are attempted

to boot in the order selected in the Hard-Disk Drive Sequence. This option is not

enabled for UEFI Boot Mode.

Boot Option

Settings

Configures the boot sequence and the boot devices.

Network Settings screen details

You can use the Network Settings screen to modify PXE device settings. The network settings option is

available only in the UEFI boot mode. BIOS does not control network settings in the BIOS boot mode. For

BIOS boot mode, the option ROM of the network controllers handles the network settings.

To view the Network Settings screen, click System Setup Main Menu → System BIOS → Network

Settings.

The Network Settings screen details are explained as follows:

Option Description

PXE Device n (n =

1 to 4)

Enables or disables the device. When enabled, a UEFI boot option is created for the

device.

PXE Device n

Settings (n = 1 to

Enables you to control the configuration of the PXE device.

Integrated Devices screen details

You can use the Integrated Devices screen to view and configure the settings of all integrated devices

including the video controller, integrated RAID controller, and the USB ports.

To view the Integrated Devices screen, click System Setup Main Menu → System BIOS → Integrated

Devices.

The Integrated Devices screen details are explained as follows:

Option Description

USB 3.0 Setting Enables or disables the USB 3.0 support. Enable this option only if your operating

system supports USB 3.0. If you disable this option, devices operate at USB 2.0

speed. USB 3.0 is disabled by default.

User Accessible

USB Ports

Enables or disables the USB ports. Selecting Only Back Ports On disables the front

USB ports, selecting All Ports Off disables all USB ports. The USB keyboard and

Option Description

mouse operates during boot process in certain operating systems. After the boot

process is complete, the USB keyboard and mouse do not work if the ports are

disabled.

NOTE: Selecting Only Back Ports On and All Ports Off disables the USB

management port and also restricts access to iDRAC features.

Internal USB Port Enables or disables the internal USB port. This option is set to Enabled by default.

Integrated RAID

Controller

Enables or disables the integrated RAID controller. This option is set to Enabled by

default.

Integrated

Network Card 1

Enables or disables the integrated network card.

Embedded NIC1

and NIC2 NOTE: The Embedded NIC1 and NIC2 options are only available on systems

that do not have Integrated Network Card 1.

Enables or disables the Embedded NIC1 and NIC2 options. If set to Disabled, the

NIC may still be available for shared network access by the embedded

management controller. The embedded NIC1 and NIC2 options are only available

on systems that do not have Network Daughter Cards (NDCs). This option is

mutually exclusive with the Integrated Network Card 1 option. Configure this

function by using the NIC management utilities of the system.

I/OAT DMA Engine Enables or disables the I/OAT option. Enable only if the hardware and software

support the feature.

Embedded Video

Controller

Allows you to enable or disable the Embedded Video Controller option. This

option is set to Enabled by default.

Current State of

Embedded Video

Controller

Displays the current state of the embedded video controller. The Current State of

Embedded Video Controller option is a read-only field. If the Embedded Video

Controller is the only display capability in the system (that is, no add-in graphics

card is installed), then the Embedded Video Controller is automatically used as the

primary display even if the Embedded Video Controller setting is set to Disabled.

SR-IOV Global

Enable

Enables or disables the BIOS configuration of Single Root I/O Virtualization (SR-

IOV) devices. This option is set to Disabled by default.

OS Watchdog

Timer

If your system stops responding, this watchdog timer aids in the recovery of your

operating system. When this option is set to Enabled, the operating system

initializes the timer. When this option is set to Disabled (the default), the timer does

not have any effect on the system.

Memory Mapped

I/O above 4 GB

Enables or disables the support for PCIe devices that require large amounts of

memory. This option is set to Enabled by default.

Slot Disablement Enables or disables the available PCIe slots on your system. The slot disablement

feature controls the configuration of PCIe cards installed in the specified slot. Slot

disablement must be used only when the installed peripheral card prevents booting

into the operating system or causes delays in system startup. If the slot is disabled,

both the Option ROM and UEFI drivers are disabled.

Serial Communication screen details

You can use the Serial Communication screen to view the properties of the serial communication port.

To view the Serial Communication screen, click System Setup Main Menu → System BIOS → Serial

Communication.

The Serial Communication screen details are explained as follows:

Option Description

Serial

Communication

Selects serial communication devices (Serial Device 1 and Serial Device 2) in BIOS.

BIOS console redirection can also be enabled and the port address can be

specified. This option is set to Auto by default.

Serial Port

Address

Enables you to set the port address for serial devices. This option is set to Serial

Device 1=COM2, Serial Device 2=COM1 by default.

NOTE: You can use only Serial Device 2 for the Serial Over LAN (SOL) feature.

To use console redirection by SOL, configure the same port address for

console redirection and the serial device.

NOTE: Every time the system boots, the BIOS syncs the serial MUX setting

saved in iDRAC. The serial MUX setting can independently be changed in

iDRAC. Loading the BIOS default settings from within the BIOS setup utility

may not always revert the serial MUX setting to the default setting of Serial

Device 1.

External Serial

Connector

Enables you to associate the External Serial Connector to Serial Device 1, Serial

Device 2, or the Remote Access Device by using this field.

NOTE: Only Serial Device 2 can be used for Serial Over LAN (SOL). To use

console redirection by SOL, configure the same port address for console

redirection and the serial device.

NOTE: Every time the system boots, the BIOS syncs the serial MUX setting

saved in iDRAC. The serial MUX setting can independently be changed in

iDRAC. Loading the BIOS default settings from within the BIOS setup utility

may not always revert this setting to the default setting of Serial Device 1.

Failsafe Baud Rate Displays the failsafe baud rate for console redirection. The BIOS attempts to

determine the baud rate automatically. This failsafe baud rate is used only if the

attempt fails, and the value must not be changed. This option is set to 115200 by

default.

Remote Terminal

Type

Sets the remote console terminal type. This option is set to VT 100/VT 220 by

default.

Redirection After

Boot

Enables or disables the BIOS console redirection when the operating system is

loaded. This option is set to Enabled by default.

System Profile Settings screen details

You can use the System Profile Settings screen to enable specific system performance settings such as

power management.

To view the System Profile Settings screen, click System Setup Main Menu → System BIOS → System

Profile Settings.

The System Profile Settings screen details are explained as follows:

Option Description

System Profile Sets the system profile. If you set the System Profile option to a mode other than

Custom, the BIOS automatically sets the rest of the options. You can only change

the rest of the options if the mode is set to Custom. This option is set to

Performance Per Watt Optimized (DAPC) by default. DAPC is Dell Active Power

Controller.

NOTE: All the parameters on the system profile setting screen available only

when the System Profile option is set to Custom.

CPU Power

Management

Sets the CPU power management. This option is set to System DBPM (DAPC) by

default. DBPM is Demand-Based Power Management.

Memory

Frequency

Sets the speed of the system memory. You can select Maximum Performance,

Maximum Reliability, or a specific speed.

Turbo Boost Enables or disables the processor to operate in turbo boost mode. This option is

set to Enabled by default.

Energy Efficient

Turbo

Enables or disables the Energy Efficient Turbo.

Energy Efficient Turbo (EET) is a mode of operation where a processor’s core

frequency is adjusted within the turbo range based on workload.

C1E Enables or disables the processor to switch to a minimum performance state when

it is idle. This option is set to Enabled by default.

C States Enables or disables the processor to operate in all available power states. This

option is set to Enabled by default.

Collaborative CPU

Performance

Control

Enables or disables the CPU power management. When set to Enabled, the CPU

power management is controlled by the OS DBPM and the System DBPM (DAPC).

This option is set to Disabled by default.

Memory Patrol

Scrub

Sets the memory patrol scrub frequency. This option is set to Standard by default.

Memory Refresh

Rate

Sets the memory refresh rate to either 1x or 2x. This option is set to 1x by default.

Uncore Frequency Enables you to select the Processor Uncore Frequency.

Dynamic mode enables the processor to optimize power resources across the

cores and uncore during runtime. The optimization of the uncore frequency to

either save power or optimize performance is influenced by the setting of the

Energy Efficiency Policy.

Energy Efficient

Policy

Enables you to select the Energy Efficient Policy.

The CPU uses the setting to manipulate the internal behavior of the processor and

determines whether to target higher performance or better power savings.

Number of Turbo

Boot Enabled

Cores for

Processor 1

NOTE: If there are two processors installed in the system, you see an entry for

Number of Turbo Boost Enabled Cores for Processor 2.

Controls the number of turbo boost enabled cores for processor 1. The maximum

number of cores is enabled by default.

Option Description

Monitor/Mwait Enables the Monitor/Mwait instructions in the processor. This option is set to

Enabled for all system profiles, except Custom by default.

NOTE: This option can be disabled only if the C States option in the Custom

mode is set to disabled.

NOTE: When C States is set to Enabled in the Custom mode, changing the

Monitor/Mwait setting does not impact the system power or performance.

System Security Settings details

The System Security Settings screen details are explained as follows:

Option Description

Intel AES-NI Improves the speed of applications by performing encryption and decryption by

using the Advanced Encryption Standard Instruction Set (AES-NI) and is set to

Enabled by default.

System Password Sets the system password. This option is set to Enabled by default and is read-only

if the password jumper is not installed in the system.

Setup Password Sets the setup password. This option is read-only if the password jumper is not

installed in the system.

Password Status Locks the system password. This option is set to Unlocked by default.

TPM Security NOTE: The TPM menu is available only when the TPM module is installed.

Enables you to control the reporting mode of the TPM. The TPM Security option is

set to Off by default. You can only modify the TPM Status, TPM Activation, and Intel

TXT fields if the TPM Status field is set to either On with Pre-boot Measurements

or On without Pre-boot Measurements.

TPM Information Changes the operational state of the TPM. This option is set to No Change by

default.

TPM Status Displays the TPM status.

TPM Command CAUTION: Clearing the TPM results in the loss of all keys in the TPM. The

loss of TPM keys may affect booting to the operating system.

Clears all the contents of the TPM. The TPM Clear option is set to No by default.

Intel TXT Enables or disables the Intel Trusted Execution Technology (TXT) option. To enable

the Intel TXT option, virtualization technology and TPM Security must be enabled

with Pre-boot measurements. This option is set to Off by default.

Power Button Enables or disables the power button on the front of the system. This option is set

to Enabled by default.

NMI Button Enables or disables the NMI button on the front of the system. This option is set to

Disabled by default.

AC Power

Recovery

Sets how the system behaves after AC power is restored to the system. This option

is set to Last by default.

AC Power

Recovery Delay

Sets the time delay for system power up after AC power is restored to the system.

This option is set to Immediate by default.

Option Description

User Defined

Delay (60s to

240s)

Sets the User Defined Delay option when the User Defined option for AC Power

Recovery Delay is selected.

UEFI Variable

Access

Provides varying degrees of securing UEFI variables. When set to Standard (the

default), UEFI variables are accessible in the operating system per the UEFI

specification. When set to Controlled, selected UEFI variables are protected in the

environment and new UEFI boot entries are forced to be at the end of the current

boot order.

Secure Boot Enables Secure Boot, where the BIOS authenticates each pre-boot image by using

the certificates in the Secure Boot Policy. Secure Boot is disabled by default.

Secure Boot

Policy

When Secure Boot policy is set to Standard, the BIOS uses the system

manufacturer’s key and certificates to authenticate pre-boot images. When Secure

Boot policy is set to Custom, the BIOS uses the user-defined key and certificates.

Secure Boot policy is set to Standard by default.

Secure Boot

Policy Summary

Displays the list of certificates and hashes that secure boot uses to authenticate

images.

Secure Boot Custom Policy Settings screen

Secure Boot Custom Policy Settings is displayed only when Secure Boot Policy is set to Custom.

In the System Setup Main Menu, click System BIOS → System Security → Secure Boot Custom Policy

Settings. The Secure Boot Custom Policy Settings screen details are explained as follows:

Menu Item Description

Platform Key Imports, exports, deletes, or restores the platform key (PK).

Key Exchange Key

Database

Enables you to import, export, delete, or restore entries in the Key Exchange Key

(KEK) Database.

Authorized

Signature

Database

Imports, exports, deletes, or restores entries in the Authorized Signature Database

(db).

Forbidden

Signature

Database

Imports, exports, deletes, or restores entries in the Forbidden Signature Database

(dbx).

Miscellaneous Settings screen details

You can use the Miscellaneous Settings screen to perform specific functions such as updating the asset

tag and changing the system date and time.

To view the Miscellaneous Settings screen, click System Setup Main Menu → System BIOS →

Miscellaneous Settings.

The Miscellaneous Settings screen details are explained as follows:

Option Description

System Time Enables you to set the time on the system.

System Date Enables you to set the date on the system.

Asset Tag Displays the asset tag and enables you to modify it for security and tracking

purposes.

Option Description

Keyboard

NumLock

Enables you to set whether the system boots with the NumLock enabled or

disabled. This option is set to On by default.

NOTE: This option does not apply to 84-key keyboards.

F1/F2 Prompt on

Error

Enables or disables the F1/F2 prompt on error. This option is set to Enabled by

default. The F1/F2 prompt also includes keyboard errors.

Load Legacy

Video Option

ROM

Enables you to determine whether the system BIOS loads the legacy video (INT

10H) option ROM from the video controller. Selecting Enabled in the operating

system does not support UEFI video output standards. This field is available only for

UEFI boot mode. You cannot set the option to Enabled if UEFI Secure Boot mode

is enabled.

In-System

Characterization

This option enables or disables In-System Characterization. By default, In-System

Characterization is set to Disabled. The two other options are Enabled and

Enabled - No Reboot.

NOTE: The default setting for In-System Characterization is subject to change

in future BIOS releases.

When enabled, In-System Characterization (ISC) executes during POST upon

detecting relevant change(s) in system configuration to optimize system power and

performance. ISC takes about 20 seconds to execute, and system reset is required

for ISC results to be applied. The Enabled - No Reboot option executes ISC and

continues without applying ISC results until the next time system reset occurs. The

Enabled option executes ISC and forces an immediate system reset so that ISC

results can be applied. It takes the system longer to be ready due to the forced

system reset. When disabled, ISC does not execute.

About Boot Manager

Boot Manager enables you to add, delete, and arrange boot options. You can also access System Setup

and boot options without restarting the system.

Entering Boot Manager

The Boot Manager screen allows you to select boot options and diagnostic utilities.

1. Turn on or restart your system.

2. Press <F11> when you see the message <F11> = Boot Manager.

If your operating system begins to load before you press <F11>, allow the system to finish booting,

and then restart your system and try again.

Boot Manager main menu

Menu item Description

Continue Normal

Boot

The system attempts to boot to devices starting with the first item in the boot

order. If the boot attempt fails, the system continues with the next item in the boot

order until the boot is successful or no more boot options are found.

Menu item Description

One Shot Boot

Takes you to the boot menu, where you can select a one time boot device to boot

from.

Launch System

Setup

Enables you to access System Setup.

Launch Lifecycle

Controller

Exits the Boot Manager and invokes the Dell Lifecycle Controller program.

System Utilities Launches System Utilities menu such as System Diagnostics and UEFI shell.

About Dell Lifecycle Controller

Dell Lifecycle Controller allows you to perform useful tasks such as configuring BIOS and hardware

settings, deploying an operating system, updating drivers, changing RAID settings, and saving hardware

profiles. For more information about Dell Lifecycle Controller, see the documentation at dell.com/

esmmanuals.

Changing the boot order

You may have to change the boot order if you want to boot from a USB key or an optical drive. The

instructions given below may vary if you have selected BIOS for Boot Mode.

1. In the System Setup Main Menu, click System BIOS → Boot Settings.

2. Click Boot Option Settings → Boot Sequence.

3. Use the arrow keys to select a boot device, and use the <+> and <-> keys to move the device down

or up in the order.

4. Click Exit, click Yes to save the settings on exit.

Choosing the system boot mode

System Setup enables you to specify the boot mode for installing your operating system:

• BIOS boot mode (the default) is the standard BIOS-level boot interface.

• UEFI boot mode is an enhanced 64-bit boot interface based on Unified Extensible Firmware Interface

(UEFI) specifications that overlays the system BIOS.

To choose the system Boot Mode:

1. In System Setup click Boot Settings and select Boot Mode.

2. Select the Boot Mode you want the system to boot into.

NOTE: After the system boots in the specified boot mode, proceed to install your operating system

from that mode.

CAUTION: Trying to boot the operating system from the other boot mode will cause the system

to halt at startup.

NOTE: Operating systems must be UEFI-compatible to be installed from the UEFI boot mode. DOS

and 32-bit operating systems do not support UEFI and can only be installed from the BIOS boot

mode.

NOTE: For the latest information on supported operating systems, go to dell.com/ossupport .

Assigning a system and setup password

Prerequisites

You can assign a new System Password and Setup Password or change an existing System Password

and Setup Password only when the password jumper setting is enabled and Password Status is

Unlocked.

If the password jumper setting is disabled, the existing System Password and Setup Password are deleted

and you need not provide the system password to boot the system.

NOTE: The password jumper enables or disables the System Password and Setup Password

features. For more information about the password jumper settings, see System board jumper

settings.

Steps

1. To enter System Setup, press <F2> immediately after a power-on or reboot.

2. From the System Setup Main Menu, select System BIOS and press <Enter>.

The System BIOS screen is displayed.

3. On the System BIOS screen, select System Security and press <Enter>.

The System Security screen is displayed.

4. On the System Security screen, verify that Password Status is Unlocked.

5. Select System Password, enter your system password, and press <Enter> or <Tab>.

Use the following guidelines to assign the system password:

• A password can have up to 32 characters.

• The password can contain the numbers 0 through 9.

• Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).

A message prompts you to re-enter the system password.

6. Re-enter the system password, and click OK.

7. Select Setup Password, enter your setup password and press <Enter> or <Tab>.

A message prompts you to re-enter the setup password.

8. Re-enter the setup password, and click OK.

9. Press <Esc> to return to the System BIOS screen. Press <Esc> again.

A message prompts you to save the changes.

NOTE: Password protection does not take effect until the system reboots.

Using your system password to secure your system

Prerequisites

NOTE: If you have assigned a setup password, the system accepts your setup password as an

alternate system password.

Steps

1. Turn on or reboot your system.

2. Type your password and press <Enter>.

Next steps

When Password Status is Locked, type the password and press <Enter> when prompted at reboot.

If an incorrect system password is entered, the system displays a message and prompts you to re-enter

your password. You have three attempts to enter the correct password. After the third unsuccessful

attempt, the system displays an error message that the system has halted and must be powered down.

Even after you shut down and restart the system, the error message is displayed until the correct

password is entered.

NOTE: You can use the Password Status option in conjunction with the System Password and

Setup Password options to protect your system from unauthorized changes.

Deleting or changing an existing system and/or setup

password

Prerequisites

Ensure that the Password jumper is set to enabled and the Password Status is set to Unlocked before

attempting to delete or change the existing System and/or Setup password. You cannot delete or change

an existing System or Setup password if the Password Status is Locked.

Steps

1. To enter System Setup, press <F2> immediately after a power-on or restart.

2. In the System Setup Main Menu, select System BIOS and press <Enter>.

The System BIOS screen is displayed.

3. In the System BIOS Screen, select System Security and press <Enter>.

The System Security screen is displayed.

4. In the System Security screen, verify that Password Status is set to Unlocked.

5. Select System Password, alter or delete the existing system password and press <Enter> or <Tab>.

6. Select Setup Password, alter or delete the existing setup password and press <Enter> or <Tab>.

NOTE: If you change the System and/or Setup password, a message prompts you to re-enter

the new password. If you delete the System and/or Setup password, a message prompts you to

confirm the deletion.

7. Press <Esc> to return to the System BIOS screen. Press <Esc> again, and a message prompts you to

save the changes.

Operating with a setup password enabled

If Setup Password is Enabled, enter the correct setup password before modifying most of the System

Setup options.

If you do not enter the correct password in three attempts, the system displays the message

Invalid Password! Number of unsuccessful password attempts: <x> System Halted!

Must power down.

Even after you shut down and restart the system, the error message is displayed until the correct

password is entered. The following options are exceptions:

• If System Password is not Enabled and is not locked through the Password Status option, you can

assign a system password.

• You cannot disable or change an existing system password.

NOTE: You can use the Password Status option in conjunction with the Setup Password option to

protect the system password from unauthorized changes.

Embedded system management

The Dell Lifecycle Controller provides advanced embedded systems management throughout the

server’s lifecycle. The Lifecycle Controller can be started during the boot sequence and can function

independently of the operating system.

NOTE: Certain platform configurations may not support the full set of features provided by the

Lifecycle Controller.

For more information about setting up the Lifecycle Controller, configuring hardware and firmware, and

deploying the operating system, see the Lifecycle Controller documentation at dell.com/support/home.

iDRAC Settings utility

The iDRAC Settings utility is an interface to set up and configure the iDRAC parameters using UEFI. You

can enable or disable various iDRAC parameters using the iDRAC Settings Utility.

NOTE: Accessing some of the features on the iDRAC Settings utility requires the iDRAC Enterprise

License upgrade.

For more information on using iDRAC, see the iDRAC User's Guide at dell.com/esmmanuals.

Entering the iDRAC Settings utility

1. Turn on or restart the managed system.

2. Press <F2> during Power-on Self-test (POST).

3. In the System Setup Main Menu page, click iDRAC Settings.

The iDRAC Settings screen is displayed.

Changing the Thermal Settings

The iDRAC Settings utility enables you to select and customize the thermal control settings for your

system.

1. Enter the iDRAC Settings utility.

2. Under iDRAC Settings → Thermal → User Option, select between the following options:

• Default

• Maximum Exhaust Temperature

• Fan Speed Offset

NOTE: When the User Option is set to the default Auto setting, the user option cannot be

modified.

3. Set the Maximum Air Exhaust Temperature or the Fan Speed Offset fields.

4. Click Back → Finish → Yes.

Installing and removing system

components

Safety instructions

WARNING: Whenever you need to lift the system, get others to assist you. To avoid injury, do not

attempt to lift the system by yourself.

WARNING: Opening or removing the system cover while the system is powered on may expose

you to a risk of electric shock.

CAUTION: Do not operate the system without the cover for a duration exceeding five minutes.

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

NOTE: It is recommended that you always use a static mat and static strap while working on

components inside the system.

NOTE: To ensure proper operation and cooling, all bays in the system must be populated at all

times with either a module or with a blank.

Before working inside your system

1. Ensure that you follow the Safety instructions.

2. Turn off the system, including any attached peripherals.

3. Disconnect the system from the electrical outlet and disconnect the peripherals.

4. If applicable, remove the system from the rack. For more information, see the Rack Installation

placemat at Dell.com/poweredgemanuals.

5. If installed, remove the front bezel.

6. Remove the system cover.

Related Tasks

Removing the front bezel

Removing the system cover

After working inside your system

1. Install the system cover.

2. If applicable, install the front bezel.

3. Reconnect the system to its electrical outlet.

4. Turn the system on, including any attached peripherals.

Related Tasks

Installing the optional front bezel

Installing the system cover

Recommended tools

You may need the following items to perform the procedures in this section:

• Key to the system keylock

• #1 and #2 Phillips screwdriver

• Wrist grounding strap connected to ground

Front bezel (optional)

Installing the optional front bezel

1. Locate and remove the bezel key.

NOTE: The bezel key is attached to the back of the bezel.

2. Hook the right end of the bezel onto the chassis.

3. Fit the free end of the bezel onto the system.

4. Lock the bezel.

Figure 12. Removing and installing the optional front bezel

1. release latch 2. keylock

3. front bezel

Removing the front bezel

1. Unlock the keylock at the left end of the bezel.

2. Lift the release latch next to the keylock.

3. Rotate the left end of the bezel away from the front panel.

4. Unhook the right end of the bezel and pull the bezel away from the system.

Removing and installing the system cover

WARNING: Whenever you need to lift the system, get others to assist you. To avoid injury, do not

attempt to lift the system by yourself.

WARNING: Installing or removing the system cover when the system is on may expose you to a

risk of electric shock.

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

CAUTION: Do not operate the system without the cover for a duration exceeding five minutes.

Removing the system cover

Prerequisites

1. Ensure that you follow the Safety instructions.

2. Turn off the system, including any attached peripherals.

3. Disconnect the system from the electrical outlet and peripherals.

4. If installed, remove the front bezel.

Steps

1. Turn the latch release lock to the unlock position.

2. Lift the latch and rotate the latch toward the back of the system.

The system cover slides back, disengaging the tabs on the system cover from the slots on the

chassis.

3. Hold the cover on both sides, and lift the cover away from the system.

Figure 13. Removing and installing the system cover

1. latch release lock 2. latch

3. system cover

Next steps

Install the system cover.

Related Tasks

Removing the front bezel

Installing the system cover

Prerequisites

Ensure that you read the Safety instructions.

Steps

1. Align the slots of the system cover with the tabs on the chassis.

2. Press the cover release latch, and push the cover toward the front of the chassis until the latch locks

into place.

3. Turn the cover latch release lock clockwise to the locked position.

Next steps

1. Install the bezel (optional).

2. Follow the procedure listed in After working inside your system.

Related Tasks

Installing the optional front bezel

Inside the system

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Figure 14. Inside the system—with a non-redundant power supply

1. control panel 2. cable routing latch

3. power supply unit 4. expansion-card riser connector (2)

5. memory-module socket (B3, B4) 6. processor 2

7. memory-module socket (B1, B2) 8. memory-module socket (A1, A5, A2, A6)

9. processor 1 10. memory-module socket (A3, A7, A4, A8)

11. cooling fan (5) 12. optical drive (optional)

Figure 15. Inside the System—with redundant power supplies

1. control panel 2. hard drive/SSD backplane

3. cable routing latch 4. power interposer board

5. power supply units (2) 6. PCIe expansion card riser (optional)

7. memory-module socket (B3, B4) 8. processor 2

9. memory-module socket (B1, B2) 10. memory-module socket (A1, A5, A2, A6)

11. processor 1 12. memory-module socket (A3, A7, A4, A8)

13. cooling fan (6) 14. hard drives/SSDs

15. optical drive

Cooling shroud

Removing the cooling shroud

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

CAUTION: Never operate your system with the cooling shroud removed. The system may get

overheated quickly, resulting in shutdown of the system and loss of data.

Steps

Hold the touch points and lift the shroud away from the system.

Figure 16. Removing and installing the cooling shroud

1. cooling shroud 2. intrusion switch

3. intrusion switch connector on the system

board

4. guide on the cooling shroud

5. guide pin

Related Tasks

Removing the front bezel

Removing the system cover

Installing the system cover

Installing the optional front bezel

Installing the cooling shroud

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

Steps

1. Align the following:

a. guide on the cooling shroud with the guide pin on the system board.

b. intrusion switch with the intrusion switch connector on the system board.

2. Lower the cooling shroud into the chassis until it is firmly seated.

When firmly seated, the memory socket numbers marked on the cooling shroud align with the

respective memory sockets.

Next steps

Follow the procedure listed in After working inside your system.

Related Tasks

Removing the front bezel

Installing the optional front bezel

System memory

Your system supports DDR4 registered DIMMs (RDIMMs).

NOTE: MT/s indicates DIMM speed in MegaTransfers per second.

Memory bus operating frequency can be 2133 MT/s, 1866 MT/s, 1600 MT/s, or 1333 MT/s depending on

the following factors:

• System profile selected (for example, Performance Optimized, Custom, or Dense Configuration

Optimized)

• Maximum supported DIMM frequency of the processors

The system contains 12 memory sockets split into four sets — two sets of 4 sockets and two sets of 2

sockets each. Each 4-socket set is organized into two channels and each 2–socket set is organized into

one channel. In each channel of the 4-socket set, the release levers of the first socket are marked white

and the second socket black. In the 2-socket set, each release lever is marked white.

NOTE: DIMMs in sockets A1 to A8 are assigned to processor 1 and DIMMs in sockets B1 to B4 are

assigned to processor 2.

Figure 17. System memory board

Memory channels are organized as follows:

Processor 1 channel 0: memory sockets A1 and A5

channel 1: memory sockets A2 and A6

channel 2: memory sockets A3 and A7

channel 3: memory sockets A4 and A8

Processor 2 channel 0: memory sockets B1

channel 1: memory sockets B2

channel 2: memory sockets B3

channel 3: memory sockets B4

The following table shows the memory populations and operating frequencies for the supported

configurations.

Table 14. Supported configurations

DIMM Type DIMMs Populated/

Channel Operating Frequency (in

MT/s) Maximum DIMM Rank/Channel

1.2 V

RDIMM 1 2133, 1866, 1600, 1333 Dual rank or single rank

2 2133, 1866, 1600, 1333 Dual rank or single rank

General memory module installation guidelines

Your system supports Flexible Memory Configuration, enabling the system to be configured and run in

any valid chipset architectural configuration. The following are the recommended guidelines for installing

memory modules:

• x4 and x8 DRAM based DIMMs can be mixed. For more information, see Mode-specific guidelines.

• Up to two dual- or single-rank RDIMMs can be populated per channel.

• Populate DIMM sockets only if a processor is installed. For single-processor systems, sockets A1 to A8

are available. For dual-processor systems, sockets A1 to A8 and sockets B1 to B4 are available.

• Populate all sockets with white release levers first, and then all the sockets with black release levers.

• When mixing memory modules with different capacities, populate the sockets with memory modules

with highest capacity first. For example, if you want to mix 4 GB and 8 GB DIMMs, populate 8 GB

DIMMs in the sockets with white release levers and 4 GB DIMMs in the sockets with black release

levers.

• In a dual-processor configuration, the memory configuration for each processor should be identical

through the first eight slots. For example, if you populate socket A1 for processor 1, then populate

socket B1 for processor 2, and so on.

• Memory modules of different capacities can be mixed provided other memory population rules are

followed (for example, 4 GB and 8 GB memory modules can be mixed).

• Mixing of more than two DIMM capacities in a system is not supported.

• Populate two DIMMs per processor (one DIMM per channel) at a time to maximize performance.

Mode-specific guidelines

Four memory channels are allocated to each processor. The allowable configurations depend on the

memory mode selected.

NOTE: You can mix x4 and x8 DRAM based DIMMs to support RAS features. However, all guidelines

for specific RAS features must be followed. x4 DRAM based DIMMs retain Single Device Data

Correction (SDDC) in memory optimized (independent channel) mode. x8 DRAM based DIMMs

require Advanced ECC mode to gain SDDC.

The following sections provide additional slot population guidelines for each mode:

Advanced ECC (lockstep)

Advanced ECC mode extends SDDC from x4 DRAM based DIMMs to both x4 and x8 DRAMs. This

protects against single DRAM chip failures during normal operation.

Memory installation guidelines:

• Memory modules must be identical in size, speed, and technology.

• DIMMs installed in memory sockets with white release levers must be identical and similar rule applies

for sockets with black release levers. This ensures that identical DIMMs are installed in matched pairs -

for example, A1 with A2, A3 with A4, A5 with A6, and so on.

NOTE: Advanced ECC with Mirroring is not supported.

Memory optimized (independent channel) mode

This mode supports SDDC only for memory modules that use x4 device width, and the mode does not

impose any specific slot population requirements.

Memory sparing

NOTE: To use memory sparing, this feature must be enabled in the System Setup.

In this mode, one rank per channel is reserved as a spare. If persistent correctable errors are detected on

a rank, the data from this rank is copied to the spare rank and the failed rank is disabled.

With memory sparing enabled, the system memory available to the operating system is reduced by one

rank per channel. For example, in a dual-processor configuration with sixteen 4 GB dual-rank DIMMs, the

available system memory is: 3/4 (ranks/channel) × 16 (DIMMs) × 4 GB = 48 GB, and not 16 (DIMMs) × 4

GB = 64 GB.

NOTE: Memory sparing does not offer protection against a multi-bit uncorrectable error.

NOTE: Both Advanced ECC/Lockstep and Optimizer modes support Memory Sparing.

Sample memory configurations

The following tables show sample memory configurations for one and two processor configurations that

follow the appropriate memory guidelines.

NOTE: 1R and 2R in the following tables indicate single- and dual-rank DIMMs respectively.

Table 15. Memory configurations—single processor

System

Capacity (in

GB)

DIMM Size

(in GB) Number of

DIMMs DIMM Rank,

Organization, and

Frequency

DIMM Slot Population

4 4 1 1R, x8, 2133 MT/s,

1R, x8, 1866 MT/s

8 4 2 1R, x8, 2133 MT/s,

1R, x8, 1866 MT/s

A1, A2

System

Capacity (in

GB)

DIMM Size

(in GB) Number of

DIMMs DIMM Rank,

Organization, and

Frequency

DIMM Slot Population

16 4 4 1R, x8, 2133 MT/s,

1R, x8, 1866 MT/s

A1, A2, A3, A4

8 2 2R, x8, 2133 MT/s,

2R, x8, 1866 MT/s

A1, A2

24 4 6 1R, x8, 2133 MT/s,

1R, x8, 1866 MT/s

A1, A2, A3, A4, A5, A6

48 8 6 2R, x8, 2133 MT/s,

2R, x8, 1866 MT/s

A1, A2, A3, A4, A5, A6

96 16 6 2R, x4, 2133 MT/s,

2R, x4, 1866 MT/s

A1, A2, A3, A4, A5, A6

128 16 8 2R, x4, 2133 MT/s,

2R, x4, 1866 MT/s,

A1, A2, A3, A4, A5, A6, A7, A8

192 32 6 RDIMM, 2R, x4, 2133

MT/s

RDIMM, 2R, x4, 1866

MT/s

A1, A2, A3, A4, A5, A6

Table 16. Memory configurations—two processors

System

Capacity (in

GB)

DIMM Size (in

GB) Number of

DIMMs DIMM Rank,

Organization, and

Frequency

DIMM Slot Population

16 4 4 1R, x8, 2133 MT/s,

1R, x8, 1866 MT/s

A1, A2, B1, B2

32 4 8 1R, x8, 2133 MT/s,

1R, x8, 1866 MT/s

A1, A2, A3, A4, B1, B2, B3, B4

64 8 8 2R, x8, 2133 MT/s,

2R, x8, 1866 MT/s

A1, A2, A3, A4, B1, B2, B3, B4

96 8 12 2R, x8, 2133 MT/s,

2R, x8, 1866 MT/s

A1, A2, A3, A4, A5, A6,A7,A8, B1,

B2, B3, B4

128 16 8 2R, x4, 2133 MT/s, A1, A2, A3, A4, B1, B2, B3, B4

System

Capacity (in

GB)

DIMM Size (in

GB) Number of

DIMMs DIMM Rank,

Organization, and

Frequency

DIMM Slot Population

2R, x4, 1866 MT/s

160 16 and 8 12 2R, x4, 2133 MT/s,

2R, x8, 2133 MT/s,

2R, x4, 1866 MT/s

2R, x8, 1866 MT/s

A1, A2, A3, A4, A5, A6,A7,A8, B1,

B2, B3, B4

NOTE: 16 GB DIMMs must

be installed in slots

numbered A1, A2, A3, A4,

B1, B2, B3, and B4 and 8

GB DIMMs must be

installed in slots A5, A6, A7,

and A8.

192 16 12 2R, x4, 2133 MT/s,

2R, x4, 1866 MT/s

A1, A2, A3, A4, A5, A6,A7,A8, B1,

B2, B3, B4

384 32 12 RDIMM, 2R, x4, 2133

MT/s

RDIMM, 2R, x4, 1866

MT/s

A1, A2, A3, A4, A5, A6,A7,A8, B1,

B2, B3, B4

Removing memory module

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the cooling shroud.

WARNING: The memory modules are hot to the touch for some time after the system has been

powered down. Allow time for the memory modules to cool before handling them. Handle the

memory modules by the card edges and avoid touching the components or metallic contacts on

the memory module.

CAUTION: To ensure proper system cooling, memory-module blanks must be installed in any

memory socket that is not occupied. Remove memory-module blanks only if you intend to install

memory modules in those sockets.

Steps

1. Locate the appropriate memory module socket.

CAUTION: Handle each memory module only by the card edges, making sure not to touch

the middle of the memory module or metallic contacts.

2. To release the memory module from the socket, simultaneously press the ejectors on both ends of

the memory-module socket.

Figure 18. Removing memory module

1. memory-module 2. memory-module socket

3. memory module ejector (2)

Related Tasks

Removing the cooling shroud

Installing memory modules

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the cooling shroud.

WARNING: The memory modules are hot to the touch for some time after the system has been

powered down. Allow time for the memory modules to cool before handling them. Handle the

memory modules by the card edges and avoid touching the components or metallic contacts on

the memory module.

Steps

1. Locate the appropriate memory-module socket.

CAUTION: Handle each memory module only by the card edges, making sure not to touch

the middle of the memory module or metallic contacts.

2. If a memory module or a memory-module blank is installed in the socket, remove it.

NOTE: Retain the removed memory-module blank(s) for future use.

CAUTION: To prevent damage to the memory module or the memory-module socket during

installation, do not bend or flex the memory module; insert both ends of the memory module

simultaneously.

3. Align the edge connector of the memory module with the alignment key of the memory module

socket, and insert the memory module in the socket.

NOTE: The memory-module socket has an alignment key that allows you to install the memory

module in the socket in only one orientation.

CAUTION: Do not apply pressure at the center of the memory module; apply pressure at both

ends of the memory module evenly.

4. Press the memory module with your thumbs until the socket levers firmly click into place.

Figure 19. Installing the memory module

1. memory module 2. alignment key

3. memory-module socket ejector (2)

When the memory module is properly seated in the socket, the levers on the memory module socket

align with the levers on the other sockets that have memory modules installed.

5. Repeat steps 3 and 4 of this procedure to install the remaining memory modules.

Next steps

1. Install the cooling shroud.

2. Follow the procedure listed in After working inside your system.

3. Press <F2> to enter System Setup, and check the System Memory setting.

The System Memory value should reflect the newly installed memory.

4. If the value is incorrect, one or more of the memory modules may not be installed properly. Repeat

step 3 and step 4 of this procedure, checking to ensure that the memory modules are firmly seated

in their sockets.

5. Run the system memory test in the system diagnostics.

Related Tasks

Removing the cooling shroud

Installing the cooling shroud

Hard drives

Depending on the configuration, your system supports one of the following:

Four hard-drive

systems

Up to four 3.5-inch cabled hard drives, or

Up to four 3.5-inch hot-swappable SAS HDD, SATA HDD, or SATA SSD or

Up to four 2.5-inch hot-swappable SAS HDD, SATA HDD, or SATA SSD

Eight hard-drive

systems

Up to eight 2.5-inch hot-swappable SAS HDD, SATA HDD, or SATA SSD

Ten hard-drive

systems

Up to ten 2.5-inch hot-swappable SATA HDD or SATA SSD

NOTE: SSD/SAS/SATA hard drives cannot be mixed in a system.

The hot-swappable hard drives connect to the system board through the hard-drive backplane. Hot-

swappable hard drives are supplied in hot-swappable hard-drive carriers that fit in the hard-drive slots.

CAUTION: Before attempting to remove or install a hot-swappable hard drive while the system is

running, see the documentation for the storage controller card to ensure that the host adapter is

configured correctly to support hot-swap hard drive removal and insertion.

CAUTION: Do not turn off or reboot your system while the hard drive is being formatted. Doing

so can cause a hard drive failure.

NOTE: Use only hard drives that have been tested and approved for use with the hard-drive

backplane.

When you format a hard drive, allow enough time for the formatting to be completed. Be aware that

high-capacity hard drives can take a number of hours to format.

Removing a 2.5 inch hard-drive blank

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

CAUTION: To maintain proper system cooling, all empty hard-drive slots must have hard-drive

blanks installed.

1. Ensure that you read the Safety instructions.

2. If installed, remove the bezel.

Steps

Press the release button and slide the hard-drive blank out of the hard-drive slot.

Figure 20. Removing and installing a 2.5 inch hard-drive blank

1. hard-drive blank 2. release button

Related Tasks

Removing the front bezel

Installing the optional front bezel

Installing a 2.5 inch hard-drive blank

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. If installed, remove the front bezel.

Steps

Insert the hard-drive blank into the hard-drive slot until the release button clicks into place.

Next steps

If applicable, install the front bezel.

Related Tasks

Removing the front bezel

Installing the optional front bezel

Removing a 3.5 inch hard-drive blank

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

CAUTION: To maintain proper system cooling, all empty hard-drive slots must have drive blanks

installed.

1. Ensure that you read the Safety instructions.

2. If installed, remove the front bezel.

Steps

Press the release button and slide the blank out of the hard-drive slot.

Figure 21. Removing and installing a 3.5 inch hard-drive blank

1. hard-drive blank 2. release button

Next steps

If applicable, install the front bezel.

Related Tasks

Removing the front bezel

Installing the optional front bezel

Installing a 3.5 inch hard-drive blank

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. If installed, remove the front bezel.

Steps

Insert the hard-drive blank into the hard-drive slot until the release button clicks into place.

Next steps

If applicable, install the front bezel.

Related Tasks

Removing the front bezel

Installing the optional front bezel

Removing a cabled hard drive

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

Steps

1. Disconnect the data/power cable from the hard drive.

2. Press the release tab on the hard-drive carrier and slide the hard drive out of the hard-drive bay.

CAUTION: To maintain proper system cooling, all empty hard-drive slots must have hard-

drive blanks installed.

3. Insert a hard-drive blank in the empty hard-drive slot.

Figure 22. Removing and installing a cabled hard drive

1. hard drive 2. power/data cable

3. release tab 4. hard-drive carrier

Installing a cabled hard drive

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Ensure that you read the Safety instructions.

Steps

1. Press the release tab on the hard-drive carrier and slide the carrier out of the system.

2. Install the hard drive into the hard-drive carrier.

3. Insert the hard-drive carrier into the hard-drive slot till it clicks into place.

4. Connect the power/data cable to the hard drive.

• If connecting to the integrated SATA controller (SATA hard drives only), connect the SATA data

cable to the SATA_A-D connector on the system board.

• If connecting to a SAS RAID controller card (SAS or SATA hard drives), connect the data cable to

the connector on the card.

Next steps

1. Follow the procedure listed in After working inside your system.

2. Reconnect the system to its electrical outlet and turn the system on, including any attached

peripherals.

3. Enter the System Setup and ensure that the hard drive's controller is enabled.

4. Exit the System Setup program and reboot the system.

5. Install any software required for the hard drive operation as described in the documentation for the

hard drive.

Removing a hot-swap hard drive

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. If installed, remove the front bezel.

3. Using the management software, prepare the hard drive for removal. For more information, see the

documentation for the storage controller.

If the hard drive is online, the green activity/fault indicator flashes as the drive is turned off. You can

remove the hard-drive when the hard-drive indicators turn off.

CAUTION: To prevent data loss, ensure that your operating system supports hot-swap drive

installation. See the documentation supplied with your operating system.

Steps

1. Press the release button to open the hard-drive carrier release handle.

2. Slide the hard-drive carrier out of the hard-drive slot.

CAUTION: To maintain proper system cooling, all empty hard-drive slots must have hard-

drive blanks installed.

3. If you are not replacing the hard drive immediately, insert a hard-drive blank in the empty hard-drive

slot.

Figure 23. Removing and installing a hot-swap hard drive

1. release button 2. hard-drive carrier

3. hard-drive carrier handle

Next steps

If removed, install the front bezel.

Installing a hot-swap hard drive

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

CAUTION: Use only hard drives that have been tested and approved for use with the hard-drive

backplane.

CAUTION: Combining SAS and SATA hard drives in the same RAID volume is not supported.

CAUTION: When installing a hard drive, ensure that the adjacent drives are fully installed.

Inserting a hard-drive carrier and attempting to lock its handle next to a partially installed carrier

can damage the partially installed carrier's shield spring and make it unusable.

CAUTION: To prevent data loss, ensure that your operating system supports hot-swap drive

installation. See the documentation supplied with your operating system.

CAUTION: When a replacement hot-swappable hard drive is installed and the system is powered

on, the hard drive automatically begins to rebuild. Make absolutely sure that the replacement

hard drive is blank or contains data that you wish to have over-written. Any data on the

replacement hard drive is immediately lost after the hard drive is installed.

Steps

1. If a hard-drive blank is installed in the hard-drive slot, remove it.

2. Install a hard drive in the hard-drive carrier.

3. Press the release button on the front of the hard-drive carrier and open the hard-drive carrier handle.

4. Insert the hard-drive carrier into the hard-drive slot until the carrier comes in contact with the

backplane.

5. Close the hard-drive carrier handle to lock the hard drive in place.

Next steps

If applicable, install the front bezel.

Installing a 2.5 inch hard drive into a 3.5 inch hard-drive adapter

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Keep the #2 Phillips screwdriver ready.

2. Ensure that you read the Safety instructions.

Steps

1. Align the screw holes on the 2.5 inch hard drive with the screw holes on the 3.5 inch hard-drive

adapter.

2. Install the screws to secure the hard drive to the hard-drive adapter.

Figure 24. Removing and Installing a 2.5 inch hard drive into a 3.5 inch hard-drive adapter

1. 2.5 inch hard drive 2. 3.5 inch hard-drive adapter

3. screw (2)

Removing a 2.5 inch hard drive from a 3.5 inch hard-drive adapter

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Keep the #2 Phillips screwdriver ready.

NOTE: A 2.5 inch hard drive is installed in a 3.5 inch hard-drive adapter, which is then installed in the

3.5 inch hard-drive carrier.

Steps

1. Remove the screws from the side of the 3.5 inch hard-drive adapter.

2. Remove the hard drive from the hard-drive adapter.

Installing a hard-drive adapter into a hard-drive carrier

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Keep the #2 Phillips screwdriver ready.

Steps

1. Insert the hard-drive adapter into the hard-drive carrier with the connector end of the hard drive

toward the back of the hard-drive carrier.

2. Align the screw holes on the hard drive with the holes on the hard-drive carrier.

3. Install the screws to secure the hard drive to the hard-drive carrier.

Figure 25. Removing and installing a hard-drive adapter into a 3.5 inch hard-drive carrier

1. 3.5 inch hard-drive carrier 2. screw (5)

3. hard-drive adapter 4. 2.5 inch hard drive

Removing a hard-drive adapter from a hard-drive carrier

Prerequisites

1. Ensure that you read the Safety instructions.

2. Keep the #2 Phillips screwdriver ready.

Steps

1. Remove the screws from the slide rails on the hard-drive carrier.

2. Lift the hard-drive adapter out of the hard-drive carrier.

Removing a hard drive from a hard-drive carrier

Prerequisites

1. Keep the #2 Phillips screwdriver ready.

2. Remove the hard-drive carrier from the system.

Steps

1. Remove the screws from the slide rails on the hard-drive carrier.

2. Lift the hard drive out of the hard-drive carrier.

Figure 26. Removing and installing a hard drive into a hard-drive carrier

1. screw (4) 2. hard drive

3. hard-drive carrier

Installing a hard drive into a hard-drive carrier

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Keep the #1 Phillips screwdriver handy.

Steps

1. Insert the hard drive into the hard-drive carrier with the connector end of the hard drive toward the

back.

2. Align the screw holes on the hard drive with the set of screw holes on the hard-drive carrier.

When aligned correctly, the back of the hard drive is flush with the back of the hard-drive carrier.

3. Attach the screws to secure the hard drive to the hard-drive carrier.

Optical drive (optional)

Removing an ultra slim optical drive

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

Steps

1. Disconnect the power/data cable from the back of the optical drive.

Observe the routing of the power and data cable inside the chassis as you remove them from the

system board and the drive. You must route these cables properly when you replace them to prevent

them from being pinched or crimped.

2. To release the optical drive, press and push the release tab toward the front of the system.

3. Slide the optical drive out of the system until it is free of the optical-drive slot.

4. If you are not adding a new optical drive, install the optical-drive blank.

Figure 27. Removing and installing an ultra slim optical drive

1. optical drive 2. data cable

3. power cable 4. release tab

Next steps

Follow the procedure listed in After working inside your system.

Installing an ultra slim optical drive

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

Steps

1. To remove the optical drive blank, press the blue release tab at the back of the blank and push the

blank out of the system.

2. Align the optical drive with the optical drive slot on the front of chassis.

3. Slide the optical drive into the slot until the latch snaps into place.

4. Connect the power/data cable to the back of the drive.

5. Route the power/data cable underneath the cable routing latch of the system.

6. Connect the power/data cable to the connectors on the system board.

Next steps

1. Follow the procedure listed in After working inside your system.

Removing the standard optical drive

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

Steps

1. Disconnect the power/data cable from the back of the optical drive.

Observe the routing of the power and data cable inside the chassis as you remove them from the

system board and the drive. You must route these cables properly when you replace them to prevent

them from being pinched or crimped.

2. Pull the release latch and disengage the optical drive from the notches on the metal standoffs.

3. Lift the optical drive out of the system.

4. If you are not adding a new optical drive, install the optical-drive blank.

Figure 28. Removing and installing the standard optical drive

1. optical drive 2. data cable

3. power cable 4. release latch

5. metal standoff (4) 6. notch on the metal standoff (2)

Next steps

Follow the procedure listed in After working inside your system.

Installing the standard optical drive

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

Steps

1. Align the two notches on the metal standoffs with the slots on the side of the optical drive.

2. Slide the optical drive into the notches until it is seated firmly and the release latch snaps into place.

3. Connect the power cable.

4. Connect the data cable to the back of the drive and to the SATA connector on the system board.

NOTE: Route and secure the cables using the cable routing latch on the system chassis to

prevent them from being pinched or crimped.

Next steps

Follow the procedure listed in After working inside your system.

Cooling fans

Your system supports:

• Up to five cooling fans in a non-redundant power supply configuration.

• Up to six cooling fans in a redundant power supply configuration.

NOTE: Fan 1 must be installed in a redundant power supply configuration.

NOTE: Hot-swap removal or installation of the fans is not supported.

NOTE: Each fan is listed in the system’s management software, referenced by the respective fan

number. If there is a problem with a particular fan, you can easily identify and replace the proper fan

by noting the fan numbers on the cooling fan assembly.

Removing a cooling fan

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

NOTE: The procedure for removing each fan is identical.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. If installed, remove the cooling shroud.

Steps

1. Disconnect the fan's power cable from the power cable connector on the system board or power

interposer board as applicable.

2. Lift the fan out of the cooling-fan bracket.

Figure 29. Removing and installing a cooling fan

1. cooling fan 2. power cable connector

3. cooling-fan bracket

Related Tasks

Removing the cooling shroud

Installing a cooling fan

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Remove the cooling shroud.

Steps

1. Facing the front of the system, lower the fan into the cooling-fan bracket.

NOTE: When aligned correctly, the fan cable is on the left of the fan.

2. Connect the fan's power cable to the power cable connector on the system board as applicable.

3. Install the cooling shroud.

Next steps

Follow the procedure listed in After working inside your system.

Related Tasks

Removing the cooling shroud

Installing the cooling shroud

Internal USB memory key (optional)

The USB memory key installed inside your system can be used as a boot device, security key, or mass

storage device.

To boot from the USB memory key, configure the USB memory key with a boot image and then specify

the USB memory key in the boot sequence in the System Setup.

NOTE: The internal USB connector is located on the system board.

Related Tasks

System board connectors

Replacing the internal USB key

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system

Steps

1. Locate the USB connector/USB key on the system board.

To locate the USB connector, see System board connectors.

2. If installed, remove the USB key.

3. Insert the USB key into the USB connector.

Figure 30. Replacing the internal USB key

1. USB memory key 2. USB memory key connector

Next steps

1. Follow the procedure listed in After working inside your system.

2. While booting, press <F2> to enter the System Setup and verify that the USB key is detected by the

system.

Expansion cards and expansion-card risers (optional)

NOTE: A missing or an unsupported expansion-card riser logs an SEL event. It does not prevent

your system from powering on and no BIOS POST message or F1/F2 pause is displayed.

Expansion card installation guidelines

Your system supports Generation 1, Generation 2, and Generation 3 cards. The following table provides

riser configurations for R430 systems:

Table 17. Expansion card slots available on the expansion-card riser

Expansion-

card riser PCIe slot on the

expansion-card

riser

Processor

connection Height Length Link

width Slot width

PCIE_G3_X16 1 Processor 1 Half Height Half

Length

x16 x16

2 Processor 1 Half Height Half

Length

x16 x16

PCIE_G3_X8 1 Processor 1 Full Height Half

Length

x8 x16

Expansion-

card riser PCIe slot on the

expansion-card

riser

Processor

connection Height Length Link

width Slot width

2 Processor 1 Half Height Half

Height

x8 x16

NOTE: The PCIE_G3_X8 and PCIE_G3_X16 are the two different types of risers supported on R430

systems. You can install an expansion card on the system board only using expansion-card riser.

NOTE: The expansion cards are not hot-swappable.

The following table provides a guide for installing expansion cards to ensure proper cooling and

mechanical fit. The expansion cards with the highest priority must be installed first using the slot priority

indicated. All other expansion cards must be installed in card priority and slot priority order.

Table 18. Expansion card installation order (LP+LP configuration)

Card priority Card type Slot priority Maximum allowed

1 RAID Integrated Storage Integrated Slot 1

RAID External Storage 2, 1 1

2 Infiniband single Port/Dual

(Mellanox)

2, 1 2

3 40 Gb NICs 2, 1 2

4 10 Gb NICs 2, 1 2

5 FC8 HBA 2, 1 2

6 1 Gb NICs 2, 1 2

7 12 GB SAS HBA 2, 1 2

HBA330 Integrated Slot 1

Table 19. Expansion card installation order (FH+LP configuration)

Card priority Card type Slot priority Maximum allowed

1 RAID Integrated Storage Integrated Slot 1

RAID External Storage Low

Profile

2 1

RAID External Storage Full Height 1 1

2 Infiniband Single Port/Dual Port

(Mellanox)

2 1

3 40 Gb NICs (Low profile) 2 1

40 Gb NICs (Full height) 1 1

4 10 Gb NICs (Low profile) 2 1

10 Gb NICs (Full height) 1 1

5 FC8 HBA (Low profile) 2 1

Card priority Card type Slot priority Maximum allowed

FC8 HBA (Full height) 1 1

6 1 Gb NICs (Low profile) 2 1

1 Gb NICs (Full height) 1 1

7 12 GB-SAS-HBA (Low profile) 2 1

12 GB-SAS-HBA (Full height) 1 1

8 Non-RAID HBA330 Integrated Slot 1

Removing the expansion-card riser

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

Steps

Holding the touch points, lift the expansion-card riser from the riser connector on the system board.

Figure 31. Removing and installing the expansion-card riser

1. expansion-card riser 2. guide on the expansion-card riser

3. guide pin on the system board 4. expansion-riser connector on the

system board

5. slot on the chassis 6. expansion-card latch

Next steps

1. Install the expansion card, if applicable.

2. Install the expansion-card riser.

3. Follow the procedure listed in After working inside your system.

Related Tasks

Removing an expansion card

Installing an expansion card

Installing the expansion-card riser

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Ensure that you read the Safety instructions.

Steps

1. If applicable, reinstall the expansion card into the expansion-card riser.

2. Align the following:

a. guide on the expansion-card riser with the guide pin on the system board.

b. expansion-card riser latch with the slot on the chassis.

3. Lower the expansion-card riser until the expansion-card riser is fully seated in the connector.

Next steps

Follow the procedure listed in After working inside your system.

Related Tasks

Removing an expansion card

Installing an expansion card

Removing an expansion card

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

Steps

1. Disconnect any cables connected to the expansion card or expansion-card riser.

2. If installed, remove the expansion-card riser.

3. Hold the expansion card by its edges and remove it from the expansion-card connector on the riser.

4. If you are removing the card permanently, install a metal filler bracket over the empty expansion slot

and close the expansion-card latch.

NOTE: You must install a filler bracket over an empty expansion slot to maintain Federal

Communications Commission (FCC) certification of the system. The brackets also keep dust

and dirt out of the system and aid in proper cooling and airflow inside the system.

Figure 32. Removing and installing the expansion card from expansion-card riser

1. expansion-card connector on the riser 2. expansion-card riser

3. expansion-card latch 4. expansion card

Next steps

Follow the procedure listed in After working inside your system.

Related Tasks

Removing the expansion-card riser

Installing the expansion-card riser

Installing an expansion card

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

Steps

1. Locate the expansion-card connector on the riser.

2. Holding the card by its edges, position the card so that the card-edge connector aligns with the

expansion-card connector.

3. Align the expansion-card bracket with the hooks on the chassis.

4. Insert the card-edge connector into the expansion-card connector until the card is fully seated.

NOTE: Ensure that the expansion card is properly seated along the chassis, so that expansion-

card latch can be closed.

5. If applicable, connect cables to the expansion card.

6. Install the expansion card-riser on the system board.

Next steps

Follow the procedure listed in After working inside your system.

Related Tasks

Removing the expansion-card riser

Installing the expansion-card riser

iDRAC ports card (optional)

The iDRAC ports card consists of the SD vFlash card slot and an iDRAC port. The iDRAC ports card is used

for advanced management of the system.

An SD vFlash card is a Secure Digital (SD) card that plugs into the SD vFlash card slot in the system. It

provides persistent on-demand local storage and a custom deployment environment that allows

automation of server configuration, scripts, and imaging. It emulates USB device(s). For more information,

see the Integrated Dell Remote Access Controller User's Guide at dell.com/esmmanuals.

Removing the iDRAC port card

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Disconnect any cables connected to the iDRAC port card.

4. If installed, remove the expansion-card riser.

Steps

1. Loosen the two screws securing the iDRAC port card holder to the system board.

2. Pull the iDRAC port card to disengage it from the connector and remove the card from the chassis.

Figure 33. Removing and Installing the iDRAC port card

1. iDRAC port card holder 2. iDRAC port

3. screw (2) 4. SD vFlash media card

5. iDRAC port card 6. iDRAC port card connector

Next steps

1. Install the expansion card, if applicable.

2. Install the expansion-card riser.

3. Follow the procedure listed in After working inside your system.

Related Tasks

Removing the expansion-card riser

Removing an expansion card

Installing an expansion card

Installing the expansion-card riser

Installing the iDRAC port card

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. If installed, remove the expansion card and the expansion card riser.

Steps

1. Align and insert the tabs on the iDRAC port card on the slots on the chassis wall.

2. Insert the iDRAC port card into the connector on the system board.

3. Tighten the two screws that secure the iDRAC port card holder to the system board.

4. Reconnect the cable to the iDRAC port card.

Next steps

1. Install the expansion card, if applicable.

2. Install the expansion-card riser.

3. Follow the procedure listed in After working inside your system.

Related Tasks

Removing the expansion-card riser

Removing an expansion card

Installing an expansion card

Installing the expansion-card riser

SD vFlash media card

A vFlash SD card is a Secure Digital (SD) card that plugs into the vFlash SD card slot in the system. It

provides persistent on-demand local storage and a custom deployment environment that allows

automation of server configuration, scripts, and imaging. It emulates USB device(s). For more information,

see the Integrated Dell Remote Access Controller User’s Guide at dell.com/esmmanuals.

Replacing an SD vFlash media card

1. Locate the SD vFlash media slot at the back of the chassis.

2. To remove the SD vFlash media card, push the card inward to release it, and pull the card from the

card slot.

Figure 34. Removing and installing the SD vFlash media card

1. SD vFlash media card 2. SD vFlash media-card slot

3. To install an SD vFlash media card, insert the contact-pin end of the SD vFlash media card into the

card slot on the module.

NOTE: The slot is keyed to ensure correct insertion of the card.

4. Press the card inward to lock it into the slot.

Internal dual SD module (optional)

The Internal Dual SD Module (IDSDM) card provides two SD card slots. This card offers the following

features:

• Dual card operation — maintains a mirrored configuration by using SD cards in both the slots and

provides redundancy.

NOTE: When the Redundancy option is set to Mirror Mode in the Integrated Devices screen of

System Setup, the information is replicated from one SD card to another.

• Single card operation — single card operation is supported, but without redundancy.

Removing an internal SD card

Prerequisites

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Steps

Locate the SD card slot on the internal dual SD module and press the card to release it from the slot.

Next steps

Follow the procedure listed in After working inside your system.

Installing an internal SD card

Prerequisites

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

NOTE: To use an SD card with your system, ensure that the Internal SD Card Port is enabled in the

System Setup.

Steps

1. Locate the SD card connector on the internal dual SD module. Orient the SD card appropriately and

insert the contact-pin end of the card into the slot.

NOTE: The slot is keyed to ensure correct insertion of the card.

2. Press the card into the card slot to lock it into place.

Next steps

Follow the procedure listed in After working inside your system.

Removing the optional internal dual SD module

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you follow the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Locate the Internal Dual SD Module (IDSDM) on the system board.

4. If installed, remove the SD card(s).

Steps

Hold the pull tab and pull the IDSDM out of the chassis.

Figure 35. Removing and installing the Internal Dual SD Module (IDSDM)

1. Internal Dual SD module 2. LED status indicator (2)

3. SD card (2) 4. SD card slot 2

5. SD card slot 1 6. IDSDM connector

The following table describes the IDSDM indicator codes:

Table 20. IDSDM indicator codes

Convention IDSDM indicator code Description

A Green Indicates that the card is online.

B Flashing green Indicates rebuild or activity.

C Flashing amber Indicates card mismatch or that the card has

failed.

Convention IDSDM indicator code Description

D Amber Indicates that the card is offline, has failed, or is

write protected.

E Not lit Indicates that the card is missing or is booting.

Next steps

1. Installing the dual SD module.

2. Follow the procedure listed in After working inside your system.

Installing the optional internal dual SD module

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you follow the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

Steps

1. Locate the Internal Dual SD Module (IDSDM) connector on the system board. To locate the internal

dual SD module connector, see .

2. Align the IDSDM with the connector on the system board.

3. Push the IDSDM until it is firmly seated on the system board.

Next steps

1. Install the SD card(s).

NOTE: Temporarily label each SD card with its corresponding slot before removal. Replace the

SD card(s) into the same slots.

2. Follow the procedure listed in After working inside your system.

Integrated storage controller card

Your system includes a dedicated expansion-card slot on the system board for an integrated controller

card. The integrated storage controller card provides the integrated storage subsystem for your system’s

internal hard drives. The controller supports SAS and SATA hard drives and also enables you to set up the

hard drives in RAID configurations as supported by the version of the storage controller included with

your system.

Removing the integrated storage controller card

Prerequisites

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the cooling shroud.

4. Keep the #2 Phillips screwdriver handy.

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Steps

1. Loosen the screws that secure the integrated storage controller cable to the integrated storage-

controller card connector on the system board.

2. Lift the integrated storage controller cable out.

3. Lift one end of the card and angle it to disengage the card from the integrated storage-controller

card holder on system board.

4. Lift the card out of the chassis.

Figure 36. Removing and installing the integrated storage controller card

1. integrated storage controller cable 2. integrated storage controller card

3. integrated storage-controller card

connector on the system board 4. integrated storage controller card

holder

Next steps

1. Replace the cooling shroud.

2. Follow the procedure listed in After working inside your system.

Related Tasks

Removing the cooling shroud

Installing the cooling shroud

Installing the integrated storage controller card

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the cooling shroud.

4. Keep the #2 Phillips screwdriver ready.

Steps

1. Align the end of the integrated storage-controller card with the integrated storage-controller card

holder.

2. Lower the connector side of the integrated storage-controller card into the integrated storage-

controller card connector on the system board.

Ensure that the tabs on the system board align with the screw holes on the integrated storage-

controller card.

3. Align the screws on the integrated storage-controller card cable with the screw holes on the

connector.

4. Tighten the screws to secure the integrated storage-controller card cable with the integrated

storage-controller card connector on the system board.

Next steps

1. Replace the cooling shroud.

2. Follow the procedure listed in After working inside your system.

Related Tasks

Removing the cooling shroud

Installing the cooling shroud

Heat sinks and processors

Use the following procedure when:

• Installing an additional processor

• Replacing a processor

NOTE: To ensure proper system cooling, you must install a processor blank in any empty processor

socket.

Removing the heat sink

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

CAUTION: Never remove the heat sink from a processor unless you intend to remove the

processor. The heat sink is necessary to maintain proper thermal conditions.

1. Ensure that you follow the Safety instructions.

2. Keep the Phillips #2 screwdriver ready.

3. Follow the procedure listed in Before working inside your system.

4. Remove the cooling shroud.

WARNING: The heat sink and processor are hot to the touch for some time after the system has

been powered down. Allow the heat sink and processor to cool before handling them.

Steps

1. Loosen one of the screws that secure the heat sink to the system board.

Allow some time (around 30 seconds) for the heat sink to loosen from the processor.

2. Loosen the screw that is diagonally opposite the screw you first removed.

3. Repeat the procedure for the remaining two screws.

4. Lift the heat sink away from the system.

Next steps

1. If you are removing only a faulty heat sink, install the replacement heat sink, if not, remove the

processor.

2. Follow the procedure listed in After working inside your system.

Removing a processor

Prerequisites

WARNING: The heat sink and processor are hot to the touch for some time after the system has

been powered down. Allow the heat sink and processor to cool before handling them.

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

CAUTION: Never remove the heat sink from a processor unless you intend to remove the

processor. The heat sink is necessary to maintain proper thermal conditions.

1. Ensure that you read the Safety instructions.

2. Keep the #2 Phillips screwdriver handy.

3. Before upgrading your system, download the latest system BIOS version from dell.com/support and

follow the instructions included in the compressed download file to install the update on your

system.

NOTE: You can update the system BIOS using the Lifecycle Controller. For more information

about Dell Lifecycle controller, see dell.com/esmmanuals.

4. Follow the procedure listed in Before working inside your system.

5. Remove the cooling shroud.

Steps

1. Loosen one of the screws that secures the heat sink to the system board.

Wait 30 seconds for the heat sink to loosen from the processor.

2. Remove the screw diagonally opposite the screw you first removed.

3. Repeat the procedure for the remaining two screws.

4. Remove the heat sink.

CAUTION: The processor is held in its socket under strong pressure. Be aware that the

release lever can spring up suddenly if not firmly grasped.

Figure 37. Processor shield opening and closing lever sequence

1. close first socket release lever 2. lock icon

3. processor 4. open first socket release lever

5. unlock icon

5. Position your thumb firmly over the processor open first socket-release lever near the unlock icon

and release the lever from the locked position by pushing down and out from under the tab.

6. Similarly, position your thumb firmly over the processor close first socket-release lever near the lock

icon and release the lever from the locked position by pushing down and out from under the tab.

Rotate the lever 90 degrees upward.

7. Lower the open first socket-release lever to lift the processor shield.

Figure 38. Removing and installing a processor

1. close first socket-release lever 2. pin-1 indicator of processor

3. processor 4. slot (4)

5. processor shield 6. open first socket-release lever

7. socket 8. socket keys (4)

8. Hold the tab on the processor shield and rotate the processor shield upward until the open first

socket-release lever lifts up.

9. Lift the processor out of the socket and leave the open first socket-release lever up so that the

socket is ready for the new processor.

CAUTION: The socket pins are fragile and can be permanently damaged. Be careful not to

bend the pins in the socket when removing the processor out of the socket.

NOTE: If you are permanently removing the processor, you must install a socket protective cap

in the vacant socket to protect the socket pins and keep the socket free of dust.

NOTE: After removing the processor, place it in an antistatic container for reuse, return, or

temporary storage. Do not touch the bottom of the processor. Touch only the side edges of

the processor.

Related Tasks

Removing the cooling shroud

Installing the cooling shroud

Installing a processor

Prerequisites

1. Ensure that you read the Safety instructions.

2. Keep the #2 Phillips screwdriver handy.

3. Before upgrading your system, download the latest system BIOS version from dell.com/support and

follow the instructions included in the compressed download file to install the update on your

system.

NOTE: You can update the system BIOS using the Lifecycle Controller.

4. Follow the procedure listed in Before working inside your system.

5. Remove the cooling shroud.

WARNING: The heat sink and processor are hot to the touch for some time after the system

has been powered down. Allow the heat sink and processor to cool before handling them.

CAUTION: Never remove the heat sink from a processor unless you intend to remove the

processor. The heat sink is necessary to maintain proper thermal conditions.

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

NOTE: If you are installing a single processor, it must be installed in socket CPU1.

Steps

1. Remove the heat sink.

2. Unpack the new processor

If the processor has previously been used in a system, remove any remaining thermal grease from

the processor using a lint-free cloth.

3. Locate the processor socket.

4. If applicable, remove the socket protective cap.

5. Position your thumb firmly over the open first socket-release lever near the unlock icon and

release the lever from the locked position by pushing down and in from under the tab.

6. Similarly, release the close first socket-release lever near the lock icon from the locked position.

Rotate the lever 90 degrees upward.

7. Hold the tab near the lock symbol on the processor shield and rotate it upward and out of the way.

8. To install the processor in the socket:

CAUTION: Positioning the processor incorrectly can permanently damage the system board

or the processor. Be careful not to bend the pins in the socket.

CAUTION: While removing or reinstalling the processor, wipe your hands of any

contaminants. Contaminants on the processor pins such as thermal grease or oil can damage

the processor.

a. Align the processor with the socket keys on the socket.

CAUTION: Do not use force to seat the processor. When the processor is positioned

correctly, it engages easily into the socket.

b. Align the pin-1 indicator of the processor with the triangle on the socket.

c. Place the processor on the socket such that the slots on the processor aligns with the socket

keys on the socket.

CAUTION: Do not use force to seat the processor. When the processor is positioned

correctly, it engages easily into the socket.

d. Close the processor shield.

e. Rotate the close first socket-release lever near the lock icon until it is locked in position.

f. Similarly, rotate the open first socket-release lever near the unlock icon to the unlocked

position.

9. To install the heat sink:

a. If applicable, remove the existing thermal grease from the heat sink using a clean lint-free cloth.

b. Apply thermal grease on the top of the processor. Use the thermal-grease syringe included with

your processor kit to apply the grease in a thin spiral on the top of the processor as shown in the

figure.

CAUTION: Applying too much thermal grease can result in excess grease coming in

contact with and contaminating the processor socket.

100

Figure 39. Applying thermal grease on the top of the processor

1. processor 2. thermal grease

3. thermal-grease syringe

NOTE: The thermal-grease is intended for one-time use only. Dispose of the syringe after

you use it.

c. Place the heat sink onto the processor.

d. Tighten the four screws to secure the heat sink to the system board.

NOTE: Tighten the screws diagonally opposite to each other. Do not over-tighten the heat

sink retention screws when installing the heat sink. To prevent over-tightening, tighten the

retention screw until resistance is felt, and stop once the screw is seated. The screw tension

should be no more than 6 in-lb (6.9 kg-cm).

Next steps

1. Install the cooling shroud.

2. Follow the procedure listed in After working inside your system.

3. While booting, press <F2> to enter the System Setup and check that the processor information

matches the new system configuration.

4. Run the system diagnostics to verify that the new processor operates correctly.

Related Tasks

Removing the cooling shroud

Installing the cooling shroud

101

Installing the heat sink

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you follow the Safety instructions.

2. Keep the Phillips #2 screwdriver ready.

3. Follow the procedure listed in Before working inside your system.

4. Remove the cooling shroud.

5. Install the processor.

Steps

1. If you are using an existing heat sink, remove the thermal grease from the heat sink by using a clean

lint free cloth.

2. Use the thermal grease syringe included with your processor kit to apply the grease in a thin spiral on

the top of the processor as shown in the following figure.

CAUTION: Applying too much thermal grease can result in excess grease coming in contact

with and contaminating the processor socket.

NOTE: The thermal grease syringe is intended for one-time use only. Dispose of the syringe

after you use it.

102

Figure 40. Applying thermal grease on the top of the processor

1. processor 2. thermal grease

3. thermal grease syringe

3. Place the heat sink onto the processor.

4. Tighten one of the four screws to secure the heat sink to the system board.

5. Tighten the screw diagonally opposite to the first screw you tightened.

NOTE: Do not overtighten the heat sink retention screws when installing the heat sink. To

prevent overtightening, tighten the retention screw until resistance is felt. The screw tension

must not be more than 6 in-lb (6.9 kg-cm).

6. Repeat the procedure for the remaining two screws.

Next steps

1. Install the cooling shroud.

2. Follow the procedure listed in After working inside your system.

3. While booting, press F2 to enter System Setup and check that the processor information matches

the new system configuration.

4. Run the system diagnostics to verify that the new processor operates correctly.

Power supplies

Your system supports the following power supplies:

• 450 W AC (non-redundant)

103

• 550 W AC (redundant)

When two identical power supplies are installed, the power supply configuration is redundant (1 + 1). In

redundant mode, power is supplied to the system equally from both power supplies to maximize

efficiency.

When only one power supply is installed, the power supply configuration is non-redundant (1 + 0). Power

is supplied to the system only by the single power supply.

NOTE: If two power supplies are used, they must be of the same type and have the same maximum

output power.

NOTE: For AC power supplies, use only PSUs with the Extended Power Performance (EPP) label on

the back. Mixing PSUs from previous generations of Dell PowerEdge servers can result in a PSU

mismatch condition or failure to power on.

Hot spare feature

Your system supports the hot spare feature that significantly reduces the power overhead associated with

power supply redundancy.

When the hot spare feature is enabled, one of the redundant PSUs is switched to the sleep state. The

active PSU supports 100 percent of the load, thus operating at higher efficiency. The PSU in the sleep

state monitors output voltage of the active PSU. If the output voltage of the active PSU drops, the PSU in

the sleep state returns to an active output state.

If having both PSUs active is more efficient than having one PSU in the sleep state, the active PSU can

also activate the sleeping PSU.

The default PSU settings are as follows:

• If the load on the active PSU is more than 50 percent, then the redundant PSU is switched to the

active state.

• If the load on the active PSU falls below 20 percent, then the redundant PSU is switched to the sleep

state.

You can configure the hot spare feature by using the iDRAC settings. For more information about iDRAC

settings, see the Integrated Dell Remote Access Controller User’s Guide available at Dell.com/

idracmanuals.

Removing a redundant power supply

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

CAUTION: The system requires one power supply for normal operation. On power-redundant

systems, remove and replace only one power supply at a time in a system that is powered on.

1. Ensure that you read the Safety instructions.

2. Disconnect the power cable from the power source.

104

3. Disconnect the power cable from the power supply and remove the straps that bundle and secure

the system cables.

NOTE: You may have to unlatch and lift the optional cable management arm if it interferes with

power-supply removal. For information about the cable management arm, see the system’s rack

documentation.

Steps

Press the release latch and pull the power supply straight out to release it from the power interposer

board and clear the chassis.

Figure 41. Removing and installing a redundant power supply

1. release latch 2. power supply connector

3. redundant power supply unit 4. connector

5. power supply handle

Installing a redundant power supply

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Ensure that you read the Safety instructions.

Steps

1. Verify that both power supplies are the same type and have the same maximum output power.

NOTE: The maximum output power (shown in Watts) is listed on the power supply label.

2. If applicable, remove the power supply blank.

105

3. Slide the new power supply into the chassis until the power supply is fully seated and the release

latch snaps into place.

NOTE: If you unlatched the cable management arm in step 3 of the previous procedure, relatch

it. For information about the cable management arm, see the system’s rack documentation.

4. Connect the power cable to the power supply and plug the cable into a power outlet.

CAUTION: When connecting the power cable, secure the cable with the strap.

NOTE: When installing, hot-swapping, or hot-adding a new power supply in a system with two

power supplies, allow several seconds for the system to recognize the power supply and

determine its status. The power-supply status indicator turns green to signify that the power

supply is functioning properly.

Removing a non-redundant power supply

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Disconnect the power cable from the power source.

3. Disconnect the power cable from the power supply and remove the straps that bundle and secure

the system cables.

4. Follow the procedure listed in Before working inside your system.

NOTE: You may have to unlatch and lift the optional cable management arm if it interferes with the

power-supply removal. For information about the cable management arm, see the system’s rack

documentation.

Steps

1. Disconnect all the power cables from the power supply to the system board, hard drives, and optical

drive.

2. Remove the screw securing the power supply to the chassis, slide and lift the power supply out of

the chassis.

106

Figure 42. Removing and installing a non-redundant power supply

1. power supply 2. screw

3. P1 cable connector 4. P2 cable connector

5. P3 cable connector 6. standoff

7. Backplane connector

Installing a non-redundant power supply

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

NOTE: A hot-swappable non-redundant power supply must be installed in Slot 1 of the power

supply bay.

Steps

1. Align the screw hole on the power supply with the standoff on the chassis.

2. Tighten the screw to secure the power supply to the chassis.

3. Connect all the power cables to the system board, hard drives, and optical drive.

107

Next steps

1. Follow the procedure listed in After working inside your system.

2. Connect the power cable to the power supply and plug the cable into a power outlet.

Removing the power supply unit blank

If you are installing a second power supply unit, remove the power supply unit blank in the bay by

pulling the blank outward.

CAUTION: To ensure proper system cooling, the power supply blank must be installed in the

second power supply bay in a non-redundant configuration. Remove the power supply blank

only if you are installing a second power supply.

Figure 43. Removing and installing the power supply blank

1. power supply blank 2. power supply bay

Installing the power supply unit blank

Install the power supply unit blank only in the second power supply unit bay.

To install the power supply unit blank, align the blank with the power supply unit bay and push it into

the chassis until it clicks into place.

System battery

Replacing the system battery

Prerequisites

WARNING: There is a danger of a new battery exploding if it is incorrectly installed. Replace the

battery only with the same or equivalent type recommended by the manufacturer. See your

safety information for additional information.

108

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the expansion-card riser.

Steps

1. Locate the battery socket, see System board connectors.

CAUTION: To avoid damage to the battery connector, you must firmly support the connector

while installing or removing a battery.

2. To eject the battery, press firmly on the edge of the positive side of the battery in the direction of the

arrow as shown in the illustration below.

Figure 44. System battery

1. positive side of battery 2. socket

3. To install a new system battery, hold the battery with the positive facing up and slide it under the

securing tabs.

4. Press the battery into the connector until it snaps into place.

Next steps

1. Install the expansion-card riser.

2. Follow the procedure listed in After working inside your system.

3. While booting, press F2 to enter the System Setup and ensure the battery is operating properly.

4. Enter the correct time and date in the System Setup Time and Date fields.

5. Exit the System Setup.

Related Tasks

Removing the expansion-card riser

109

Removing an expansion card

Installing an expansion card

Installing the expansion-card riser

Hard-drive backplane

Depending on your system configuration:

PowerEdge R430

supports

Four 3.5 inch or 2.5 inch SAS/SATA backplane or

Eight 2.5 inch SAS/SATA backplane or

Ten 2.5 inch SAS/SATA backplane

Removing the hard-drive backplane

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

CAUTION: To prevent damage to the drives and backplane, you must remove the hard drives

from the system before removing the backplane.

CAUTION: You must note the number of each hard drive and temporarily label them before

removal so that you can replace them in the same locations.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove all hard drives.

Steps

1. Disconnect the SAS/SATA data, signal, and power cable(s) from the backplane.

2. Press the release tabs and lift the backplane upward and slide it toward the back of the chassis.

110

Figure 45. Removing and Installing the 3.5 inch or 2.5 inch (x4) SAS/SATA backplane

1. guide (2) 2. hard-drive/SSD backplane

3. release tab (2) 4. backplane power cable

5. backplane signal cable 6. SAS_A connector on the backplane

7. hard-drive/SSD connector (4)

111

Figure 46. Cabling diagram—3.5 inch or 2.5 inch (x4) SAS/SATA backplane

1. SW_RAID_A connector on the system

board 2. SATA_CDROM connector on the

system board

3. cable routing latch 4. SAS_A connector on the backplane

5. Optical Disk Drive (ODD) 6. hard-drive backplane

7. system board

112

Figure 47. Removing and installing the 2.5 inch (x8) SAS/SATA backplane

1. hard-drive/SSD backplane 2. backplane power cable

3. backplane signal cable 4. SAS_A cable connector

5. release tab (2) 6. SAS_B cable connector

7. hard-drive/SSD connector (8)

113

Figure 48. Cabling diagram—2.5 inch (x8) SAS/SATA backplane

1. integrated storage controller card 2. SATA_CDROM connector on the

system board

3. cable routing latch 4. Optical Disk Drive (ODD)

5. SAS_A connector on the backplane 6. SAS_ B connector on the backplane

7. hard-drive/SSD backplane 8. system board

114

Figure 49. Removing and installing the 2.5 inch (x10) SAS/SATA backplane

1. hard drive/SSD backplane 2. backplane power cable

3. release tab (2) 4. SAS_A connector on the backplane

5. hard drive/SSD connector (10) 6. SAS_B connector on the backplane

7. SAS_C connector on the backplane

115

Figure 50. Cabling diagram—2.5 inch (x10) SAS/SATA backplane

1. SW_RAID_A connector on the system

board 2. SW_RAID_B connector on the system

board

3. SATA_HDD8 connector on the system

board 4. SATA_HDD9 connector on the system

board

5. cable routing latch 6. SAS_A connector on the backplane

7. SAS_B connector on the backplane 8. SAS_C connector on the backplane

9. hard drive/SSD backplane 10. system board

Related Tasks

Removing a hot-swap hard drive

116

Installing the hard-drive backplane

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

CAUTION: To prevent damage to the control panel flex cable, do not to bend the control panel

flex cable after it is inserted into the connector.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

Steps

1. Use the hooks on the chassis as guides to align the hard-drive backplane.

2. Slide down the hard-drive backplane until the release tabs snap into place.

3. Connect the SAS/SATA/SSD data, signal, and power cable(s) to the backplane.

Next steps

1. Install the hard drives in their original locations.

2. Follow the procedure listed in After working inside your system.

Related Tasks

Installing a hot-swap hard drive

Control-panel assembly

Removing the control panel

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Keep the #2 Phillips screwdriver handy.

Steps

1. Using a #2 Phillips screwdriver, remove the screw(s) securing the control panel to the chassis.

CAUTION: Do not use excessive force when removing the control panel as it can damage the

connectors.

2. Release the locking tabs of the control panel by angling the control panel up and away from the

system.

117

For an eight 2.5 inch hot-swappable hard-drive chassis, remove the screw (located at the bottom of

the chassis) that secures the control panel to the chassis.

For a ten 2.5 inch hot-swappable hard-drive chassis, Press the control panel latch and slide the

control panel out of the chassis.

3. Remove all the cables connecting the control panel to the chassis.

Figure 51. Removing and installing the control panel—four 3.5 inch hard-drives chassis

1. control panel 2. notches (6)

118

Figure 52. Removing and installing the control panel—eight 2.5 inch hard-drives/SSDs chassis

1. control panel 2. notches (4)

3. control panel module 4. LCD connector cable

119

Figure 53. Removing and installing the control panel—ten 2.5 inch hard-drives/SSDs chassis

1. screw 2. control panel release latch

3. cable securing clip 4. control panel cable connecting to the

system board

5. J_FP_USB connector cable 6. control panel

Next steps

1. Replace the control panel.

2. Follow the procedure listed in After working inside your system.

Related Tasks

Installing the control panel

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

120

1. Ensure that you read the Safety instructions.

2. Keep the #2 Phillips screwdriver handy.

Steps

Align the locking tabs on the control panel with the notches on the chassis and angle the control

panel until it snaps into place.

When properly seated, the control panel will be flush with the front panel.

NOTE: For an eight 2.5 inch hard drive chassis, tighten the screw to secure the control panel to

the bottom of the chassis.

NOTE: For a ten 2.5 inch hard-drive chassis, slide the control panel into the chassis and secure

the module with the screw.

Next steps

Follow the procedure listed in After working inside your system.

Removing the control-panel module

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

CAUTION: Do not use excessive force when removing the control panel as it can damage the

connectors.

Steps

1. Remove the screw(s) securing the control-panel module to the chassis.

2. For a 3.5 inch cabled hard-drive chassis:

a. Remove the screw(s) securing the LED panel to the chassis.

b. Remove the LED panel.

3. Remove all the cables connecting the control-panel module to the chassis.

121

Figure 54. Removing and installing the control-panel module—four cabled hard-drive chassis

1. screw (2) 2. control-panel module connector cable

3. control panel module 4. USB connector cable

5. control panel 6. LED-panel screw (2)

7. LED panel

122

Figure 55. Removing and installing the control panel module—four hard-drive chassis

1. control-panel module 2. control-panel module screws (2)

3. control-panel module connector cable 4. display module cable

5. USB connector cable

123

Figure 56. Removing and Installing the control panel module—eight hard-drive chassis

1. control panel module 2. screw (2)

3. control-panel module connector cable 4. display module cable

Installing the control-panel module

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

Steps

1. For a 3.5 inch cabled hard drive system:

a. Insert the LED panel into the slot in the chassis.

b. Secure the LED panel with the screws.

2. Insert the control-panel module into the slot in the chassis and align the two screw holes on the

control-panel module with the corresponding holes on the chassis.

3. Secure the control-panel module with the screws.

124

4. Connect all the applicable cables to the control-panel module.

Next steps

Follow the procedure listed in After working inside your system.

Power interposer board

Removing the power interposer board

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

NOTE: The power interposer board is present only in systems that support redundant power

supplies.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the power supplies from the system.

Steps

1. Disconnect the power distribution cables from the system board.

2. Disconnect the fan cable.

3. Remove the two screws securing the power interposer board to the chassis and lift the board out of

the chassis.

125

Figure 57. Removing and installing the power interposer board

1. standoffs (2) 2. power interposer board

3. fan cable connector 4. screw (2)

5. power supply cables to the system board

(3)

Installing the power interposer board

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Ensure that you read the Safety instructions.

Steps

1. Align the power interposer board with the standoffs on the chassis.

2. Install the two screws that secure the power interposer board to the chassis.

3. Connect the power distribution cables to the system board and fan cable connector to the power

interposer board.

126

Next steps

Follow the procedure listed in After working inside your system.

System board

Removing the system board

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

CAUTION: If you are using the Trusted Program Module (TPM) with an encryption key, you may

be prompted to create a recovery key during program or System Setup. Be sure to create and

safely store this recovery key. If you replace this system board, you must supply the recovery key

when you restart your system or program before you can access the encrypted data on your hard

drives.

CAUTION: Do not attempt to remove the TPM plug-in module from the system board. Once the

TPM plug-in module is installed, it is cryptographically bound to that specific system board. Any

attempt to remove an installed TPM plug-in module breaks the cryptographic binding, and it

cannot be re-installed or installed on another system board.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the following:

a. cooling shroud

b. memory modules

c. cooling fan cables

d. expansion cards

e. expansion-card riser

f. integrated storage controller card

g. heat sink and processor

h. internal dual SD module

Steps

1. Disconnect all other cables from the system board.

CAUTION: Take care not to damage the system identification button while removing the

system board from the chassis.

2. Remove the nine screws on the system board and slide the system board toward the front of the

system.

3. Hold the system board t-handle and lift the system board out of the chassis.

NOTE: To prevent damage to the system board, ensure that you hold the system board by its

edges only.

CAUTION: Do not lift the system board assembly by holding a memory module, processor, or

other components.

127

Figure 58. Removing and installing the system board

1. screw (9) 2. system board

3. system board t-handle

Related Tasks

Removing the cooling shroud

Removing memory module

Removing a cooling fan

Removing an expansion card

Removing the expansion-card riser

Removing the integrated storage controller card

Removing a processor

Removing an internal SD card

128

Installing the system board

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

CAUTION: Do not lift the system board assembly by holding a memory module, processor, or

other components.

CAUTION: Take care not to damage the system identification button while placing the system

board into the chassis.

1. Ensure that you read the Safety instructions.

2. Unpack the new system board assembly.

Steps

1. Hold the system board by its edges and the system board t-handle, and angle it toward the back of

the chassis.

2. Lower the system board into the chassis till the connectors at the back of the system board align

with the slots on the rear wall of the chassis, and the screw holes on the system board align with the

standoffs on the chassis.

3. Tighten the nine screws that secure the system board to the chassis.

Next steps

1. Install the Trusted Platform Module (TPM). See, Installing the Trusted Platform Module .

2. Replace the following:

a. internal dual SD module

b. heat sink/heat sink blank and processor/processor blank

c. expansion card riser

d. expansion cards

e. integrated storage controller card

f. memory modules

g. cooling shroud

3. Reconnect all cables to the system board.

NOTE: Ensure that the cables inside the system are routed through the cable routing latch.

4. Follow the procedure listed in After working inside your system.

5. Import your new or existing iDRAC Enterprise license. For more information, see the Integrated Dell

Remote Access Controller User’s Guideat Dell.com/support/home.

6. Ensure that you:

a. Use the Easy Restore feature to restore the service tag. See Restoring the Service Tag using Easy

Restore.

129

b. If the Service Tag is not backed up in the backup flash device, enter the system service tag

manually. See Entering the system Service Tag using System Setup.

c. Update the BIOS and iDRAC versions.

d. Re-enable the Trusted Platform Module (TPM). See Re-enabling the TPM for BitLocker users

orRe-enabling the TPM for TXT users.

Related Tasks

Installing the cooling shroud

Installing memory modules

Installing a cooling fan

Installing an expansion card

Installing the expansion-card riser

Installing the integrated storage controller card

Installing a processor

Removing an internal SD card

Restoring the Service Tag using Easy Restore

Use the Easy Restore feature if you do not know the Service Tag of your system. The Easy Restore feature

allows you to restore your system’s Service Tag, license, UEFI configuration, and the system configuration

data after replacing the system board. All data is backed up in a backup flash device automatically. If BIOS

detects a new system board and the Service Tag in the backup flash device, BIOS prompts the user to

restore the backup information.

1. Turn on the system.

If BIOS detects a new system board, and if the Service Tag is present in the backup flash device, BIOS

displays the Service Tag, the status of the license, and the UEFI Diagnostics version.

2. Do one of the following:

• Press Y to restore the Service Tag, license, and diagnostics information.

• Press N to navigate to the Lifecycle Controller based restore options.

• Press <F10> to restore data from a previously created Hardware Server Profile.

After the restore process is complete, BIOS prompts to restore the system configuration data.

3. Do one of the following:

• Press Y to restore the system configuration data.

• Press N to use the default configuration settings.

After the restore process is complete, the system restarts.

Entering the system Service Tag using System Setup

If you know the system Service Tag, use the System Setup menu to enter the Service Tag.

1. Turn on the system.

2. Press <F2> to enter the System Setup.

3. Click Service Tag Settings.

4. Enter the Service Tag.

NOTE: You can enter the only when the Service Tag field is empty. Ensure that you enter the

correct Service Tag. Once the Service Tag is entered, it cannot be updated or changed.

5. Click Ok.

130

6. Import your new or existing iDRAC Enterprise license.

For more information, see Integrated Dell Remote Access Controller User's Guide, at dell.com/

esmmanuals.

Trusted Platform Module

The Trusted Platform Module (TPM) is used to generate/store keys, protect/authenticate passwords, and

create/store digital certificates. TPM can also be used to enable the BitLocker hard drive encryption

feature in Windows Server.

CAUTION: Do not attempt to remove the Trusted Platform Module (TPM) from the system board.

Once the TPM is installed, it is cryptographically bound to that specific system board. Any

attempt to remove an installed TPM breaks the cryptographic binding, and it cannot be re-

installed or installed on another system board.

Installing the Trusted Platform Module

Prerequisites

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

CAUTION: Do not remove an installed Trusted Platform Module (TPM). Any attempt to remove an

installed TPM from the system board may damage the TPM.

Steps

1. Align the edge connectors on the TPM with the slot on the TPM connector.

2. Insert the TPM into the TPM connector such that the plastic bolt aligns with the slot on the system

board.

3. Press the plastic bolt until the bolt snaps into place.

131

Figure 59. Installing the TPM

1. TPM 2. TPM connector

3. slot on the TPM connector 4. plastic bolt

5. slot on the system board

Next steps

Follow the procedure listed in After working inside your system.

Re-enabling the TPM for BitLocker users

Initialize the TPM.

For more information on initializing the TPM, see http://technet.microsoft.com/en-us/library/

cc753140.aspx.

The TPM Status changes to Enabled, Activated.

Re-enabling the TPM for TXT users

1. While booting your system, press <F2> to enter System Setup.

2. In the System Setup Main Menu, click System BIOS → System Security Settings.

3. In the TPM Security option, select On with Pre-boot Measurements.

4. In the TPM Command option, select Activate.

5. Save the settings.

6. Restart your system.

7. Enter System Setup again.

8. In the System Setup Main Menu, click System BIOS → System Security Settings.

9. In the Intel TXT option, select On.

132

Troubleshooting your system

Safety first—for you and your system

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Troubleshooting system startup failure

If you boot the system to the BIOS boot mode after installing an operating system from the UEFI Boot

Manager, the system hangs. The reverse is also true. You must boot to the same boot mode in which you

installed the operating system.

For all other startup issues, note the system messages that appear on the screen.

Troubleshooting external connections

Ensure that all external cables are securely attached to the external connectors on your system before

troubleshooting any external devices.

Troubleshooting the video subsystem

1. Check the system and power connections to the monitor.

2. Check the video interface cabling from the system to the monitor.

3. Run the appropriate diagnostic test.

If the tests run successfully, the problem is not related to video hardware.

If the tests fail, see Getting Help.

Troubleshooting a USB device

About this task

Use the following steps to troubleshoot a USB keyboard/mouse. For other USB devices, go to step 7.

Steps

1. Disconnect the keyboard and mouse cables from the system and reconnect them.

2. If the problem persists, connect the keyboard/mouse to the USB port(s) on the opposite side of the

system.

133

3. If the problem is resolved, restart the system, enter the System Setup, and check if the non-

functioning USB ports are enabled.

Check if USB 3.0 is enabled in System Setup. If enabled, disable it and see if the issue is resolved

(older operating systems may not support USB 3.0).

4. In the IDRAC Settings Utility, ensure the USB Management Port Mode is configured as Automatic or

Standard OS Use.

5. Replace the keyboard/mouse with a working keyboard/mouse.

If the problem is not resolved, proceed to the next step to begin troubleshooting other USB devices

attached to the system.

6. Power down all attached USB devices and disconnect them from the system.

7. Restart the system and, if your keyboard is functioning, enter the System Setup.

8. Verify that all USB ports are enabled on the Integrated Devices screen, in the System Setup options.

9. Check if USB 3.0 is enabled in System Setup. If it is enabled, disable it and restart your system.

If your keyboard is not functioning, you can also use remote access.

10. If the system is not accessible, reset the NVRAM_CLR jumper inside your system and restore the

BIOS to the default settings.

11. In the IDRAC Settings Utility, ensure the USB Management Port Mode is configured as Automatic or

Standard OS Use.

12. Reconnect and power on each USB device one at a time.

13. If a USB device causes the same problem, power down the device, replace the USB cable with a

known good cable, and power up the device.

Next steps

If all troubleshooting fails, see Getting Help.

Troubleshooting a serial I/O device

Steps

1. Turn off the system and any peripheral devices connected to the serial port.

2. Swap the serial interface cable with a working cable, and turn on the system and the serial device.

If the problem is resolved, replace the interface cable with a known good cable.

3. Turn off the system and the serial device, and swap the device with a comparable device.

4. Turn on the system and the serial device.

Next steps

If the problem persists, see Getting Help.

Troubleshooting a NIC

Steps

1. Run the appropriate diagnostic test. See Using System Diagnostics for available diagnostic tests.

2. Reboot the system and check for any system messages pertaining to the NIC controller.

3. Check the appropriate indicator on the NIC connector:

• If the link indicator does not glow, check all cable connections.

• If the activity indicator does not glow, the network driver files might be damaged or missing.

134

Remove and reinstall the drivers if applicable. See the NIC's documentation.

• If applicable, change the autonegotiation setting.

• Use another connector on the switch or hub.

4. Ensure that the appropriate drivers are installed and the protocols are bound. See the NIC's

documentation.

5. Enter the System Setup and confirm that the NIC ports are enabled on the Integrated Devices

screen.

6. Ensure that the NICs, hubs, and switches on the network are all set to the same data transmission

speed and duplex. See the documentation for each network device.

7. Ensure that all network cables are of the proper type and do not exceed the maximum length.

Next steps

If all troubleshooting fails, see Getting Help.

Troubleshooting a wet system

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Steps

1. Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

2. Remove the system cover.

3. Remove the following components from the system:

• hard drives

• hard-drive backplane

• USB memory key

• hard-drive tray

• cooling shroud

• expansion-card risers (if present)

• expansion cards

• power supply unit(s)

• cooling-fan assembly (if present)

• cooling fans

• processor(s) and heat sink(s)

• memory modules

4. Let the system dry thoroughly for at least 24 hours.

5. Reinstall the components you removed in step 3.

6. Install the system cover.

7. Turn on the system and attached peripherals.

If the system does not start properly, see Getting Help.

8. If the system starts properly, shut down the system, and reinstall all the expansion cards that you

removed.

135

9. Run the appropriate diagnostic test. For more information, see Using System Diagnostics.

Next steps

If the tests fail, see Getting Help.

Troubleshooting a damaged system

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Steps

1. Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

2. Remove the system cover.

3. Ensure that the following components are properly installed:

• Cooling shroud

• Expansion-card risers (if present)

• Expansion cards

• Power supply(s)

• Cooling-fan assembly (if present)

• Cooling fans

• Processor(s) and heat sink(s)

• Memory modules

• Hard-drive carriers

• Hard-drive backplane

4. Ensure that all cables are properly connected.

5. Install the system cover.

6. Run the appropriate diagnostic test. For more information, see Using System Diagnostics.

Next steps

If the tests fail, see Getting Help.

Troubleshooting the system battery

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

NOTE: If the system is turned off for long periods of time (for weeks or months), the NVRAM may

lose its system configuration information. This situation is caused by a defective battery.

136

Steps

1. Re-enter the time and date in the System Setup.

2. Turn off the system and disconnect it from the electrical outlet for at least one hour.

3. Reconnect the system to the electrical outlet and turn on the system.

4. Enter the System Setup.

If the date and time are not correct in the System Setup, check the SEL for system battery messages.

Next steps

If the problem persists, see Getting Help.

NOTE: Some software may cause the system time to speed up or slow down. If the system seems

to operate normally except for the time kept in the System Setup, the problem may be caused by

software rather than by a defective battery.

Troubleshooting power supply units

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Power source problems

1. Press the power button to ensure that your system is turned on. If the power indicator does not light

up when the power button is pressed, press the power-on button firmly.

2. Plug in another working device to ensure that the system board is not faulty.

3. Ensure that no loose connections exist.

For example, loose power cables.

4. Ensure that the power source meets applicable standards.

5. Ensure that there are no short circuits.

6. Have a qualified electrician check the line voltage to ensure that it meets the required specifications.

Power supply unit problems

1. Ensure that no loose connections exist.

For example, loose power cables.

2. Ensure that the power supply handle/LED indicates that the power supply is working properly.

3. If you have recently upgraded your system, ensure that the power supply unit has enough power to

support the new system.

4. If you have a redundant power supply configuration, ensure that both the power supply units are of

the same type and wattage.

If the LED You may have to upgrade to a higher wattage power supply unit.

5. Ensure that you use only power supply units with the Extended Power Performance (EPP) label on

the back.

6. Reseat the power supply unit.

137

NOTE: After installing a power supply unit, allow several seconds for the system to recognize

the power supply unit and determine if it is working properly.

If the problem persists, see Getting Help.

Troubleshooting cooling problems

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Ensure that the following conditions exist:

• System cover, cooling shroud, EMI filler panel, memory-module blank, or back-filler bracket is not

removed.

• Ambient temperature is not too high.

• External airflow is not obstructed.

• A cooling fan is not removed or has not failed.

• The expansion card installation guidelines have been followed.

Additional cooling can be added by one of the following methods:

From the iDRAC Web GUI

1. Click Hardware → Fans → Setup.

2. From the Fan Speed Offset drop-down list, select the cooling level needed or set the minimum fan

speed to a custom value.

From F2 System Setup

1. Select iDRAC Settings → Thermal, and set a higher fan speed from the fan speed offset or minimum

fan speed.

From RACADM commands

1. Run the command racadm help system.thermalsettings

For more information, see the Integrated Dell Remote Access User’s Guide at dell.com/esmmanuals.

Troubleshooting cooling fans

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

NOTE: In the event of a problem with a particular fan, the fan number is referenced by the system’s

management software, allowing you to easily identify and replace the proper fan by noting the fan

numbers on the cooling fan assembly.

138

Steps

1. Remove the system cover.

2. Reseat the fan or the fan's power cable.

3. Install the system cover.

4. Restart your system.,

Next steps

If the problem persists, see Getting Help.

Troubleshooting system memory

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Steps

1. If the system is operational, run the appropriate diagnostic test. See Using system diagnostics for

available diagnostic tests.

If diagnostics indicate a fault, follow the corrective actions provided by the diagnostic program.

2. If the system is not operational, turn off the system and attached peripherals, and unplug the system

from the power source. Wait at least 10 seconds and then reconnect the system to the power

source.

3. Turn on the system and attached peripherals and note the messages on the screen.

If an error message is displayed indicating a fault with a specific memory module, go to step 12.

4. Enter the System Setup and check the system memory setting. Make any changes to the memory

settings, if needed.

If the memory settings match the installed memory but the problem still persists, go to step 12.

5. Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

6. Remove the system cover.

7. Check the memory channels and ensure that they are populated correctly.

NOTE: See the system event log or system messages for the location of the failed memory

module. Reinstall the memory device.

8. Reseat the memory modules in their sockets.

9. Install the system.

10. Enter the System Setup and check the system memory setting.

If the problem is not resolved, proceed with the next step.

11. Remove the system cover.

12. If a diagnostic test or error message indicates a specific memory module as faulty, swap or replace

the module with a known good memory module.

13. To troubleshoot an unspecified faulty memory module, replace the memory module in the first

DIMM socket with a module of the same type and capacity.

If an error message is displayed on the screen, this may indicate a problem with the installed DIMM

type(s), incorrect DIMM installation, or defective DIMM(s). Follow the on-screen instructions to

resolve the problem.

139

14. Install the system cover.

15. As the system boots, observe any error message that is displayed and the diagnostic indicators on the

front of the system.

16. If the memory problem persists, repeat step 12 through step 15 for each memory module installed.

Next steps

If the problem persists after all memory modules have been checked, see Getting Help.

Troubleshooting an internal USB key

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Steps

1. Enter the System Setup and ensure that the USB key port is enabled on the Integrated Devices

screen.

2. Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

3. Remove the system cover.

4. Locate the USB key and reseat it.

5. Install the system cover.

6. Turn on the system and attached peripherals and check if the USB key is functioning.

7. If the problem is not resolved, repeat step 2 and step 3.

8. Insert a different USB key that you know works properly.

9. Install the system cover.

Next steps

If the problem is not resolved, see Getting Help.

Troubleshooting an SD card

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

NOTE: Certain SD cards have a physical write-protect switch on the card. If the write-protect switch

is turned on, the SD card is not writeable.

Steps

1. Enter the System Setup and ensure that the Internal SD Card Port is enabled.

2. Turn off the system, including any attached peripherals, and disconnect the system from the

electrical outlet.

3. Remove the system cover.

140

NOTE: When an SD card failure occurs, the internal dual SD module controller notifies the

system. On the next restart, the system displays a message indicating the failure. If redundancy

is enabled at the time of SD card failure, a critical alert will be logged and chassis health will

degrade.

4. Replace the failed SD card with a new SD card.

5. Install the system cover.

6. Reconnect the system to its electrical outlet and turn the system on, including any attached

peripherals.

7. Enter the System Setup and ensure that the Internal SD Card Port and Internal SD Card Redundancy

mode is set to the required mode.

Verify that correct SD slot is set as Primary SD Card.

8. Check if the SD card is functioning properly.

9. If the Internal SD Card Redundancy option is set to Enabled at the time of the SD card failure, the

system will prompt you to perform a rebuild.

NOTE: The rebuild will always be sourced from the primary SD card to the secondary SD card.

Perform the rebuild of the SD card as necessary.

Troubleshooting an optical drive

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Steps

1. Try using a different CD or DVD.

2. Enter the System Setup and ensure that the integrated SATA controller and the drive's SATA port are

enabled.

3. Run the appropriate diagnostic test.

4. Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

5. If installed, remove the front bezel.

6. Remove the system cover.

7. Ensure that the interface cable is securely connected to the optical drive and to the controller.

8. Ensure that a power cable is properly connected to the drive.

9. Install the system cover.

Next steps

If the problem is not resolved, see Getting Help.

141

Troubleshooting a tape backup unit

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Steps

1. Use a different tape cartridge.

2. Ensure that the device drivers for the tape backup unit are installed and are configured correctly. See

your tape drive documentation for more information about device drivers.

3. Reinstall the tape-backup software as instructed in the tape-backup software documentation.

4. Ensure that the interface cable of the tape drive is connected to the external port on the controller

card.

5. Perform the following steps to ensure that the controller card is properly installed:

a. Turn off the system and attached peripherals, and disconnect the system from the electrical

outlet.

b. Remove the system cover.

c. Reseat the controller card in the expansion card slot.

d. Install the system cover.

e. Turn on the system and attached peripherals.

6. Run the appropriate diagnostic test. For more information, see Using System Diagnostics.

Next steps

If you cannot resolve the problem, see Getting Help.

Troubleshooting a hard drive

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

CAUTION: This troubleshooting procedure can erase data stored on the hard drive. Before you

proceed, back up all files on the hard drive.

Steps

1. Run the appropriate diagnostic test. For more information, see Using System Diagnostics.

Depending on the results of the diagnostics test, proceed as needed through the following steps.

2. If your system has a RAID controller and your hard drives are configured in a RAID array, perform the

following steps:

a. Reboot the system and press <F10> during system startup to run the Lifecycle Controller, and

then run the Hardware Configuration wizard to check the RAID configuration.

See the Lifecycle Controller documentation or online help for information on RAID configuration.

b. Ensure that the hard drive(s) are configured correctly for the RAID array.

142

c. Take the hard drive offline and reseat the drive.

d. Exit the configuration utility and allow the system to boot to the operating system.

3. Ensure that the required device drivers for your controller card are installed and are configured

correctly. See the operating system documentation for more information.

4. Reboot the system and enter the System Setup.

5. Verify that the controller is enabled and the drives are displayed in the System Setup.

Next steps

If the problem persists, try troubleshooting the expansion cards or see Getting Help.

Troubleshooting a storage controller

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

NOTE: When troubleshooting a SAS or PERC controller, see the documentation for your operating

system and the controller.

1. Run the appropriate diagnostic test. For more information, see Using System Diagnostics.

2. Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

3. Remove the system cover.

4. Verify that the installed expansion cards are compliant with the expansion card installation

guidelines.

5. Ensure that each expansion card is firmly seated in its connector.

6. Install the system cover.

7. Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.

8. If the problem is not resolved, turn off the system and attached peripherals, and disconnect the

system from the electrical outlet.

9. Remove the system cover.

10. Remove all expansion cards installed in the system.

11. Install the system cover.

12. Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.

13. Run the appropriate diagnostic test. For more information, see Using System Diagnostics. If the tests

fail, see Getting Help.

14. For each expansion card you removed in step 10, perform the following steps:

a. Turn off the system and attached peripherals, and disconnect the system from the electrical

outlet.

b. Remove the system cover.

c. Reinstall one of the expansion cards.

d. Install the system cover.

e. Run the appropriate diagnostic test. For more information, see Using System Diagnostics.

If the tests fail, see Getting Help.

143

Troubleshooting expansion cards

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

NOTE: When troubleshooting an expansion card, see the documentation for your operating system

and the expansion card.

Steps

1. Run the appropriate diagnostic test. For more information, see Using System Diagnostics .

2. Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

3. Open the system.

4. Ensure that each expansion card is firmly seated in its connector.

5. Close the system.

6. If the problem is not resolved, turn off the system and attached peripherals, and disconnect the

system from the electrical outlet.

7. Open the system.

8. Remove all expansion cards installed in the system.

9. Close the system.

10. Run the appropriate diagnostic test. For more information, see Using System Diagnostics .

If the tests fail, see Getting Help.

11. For each expansion card you removed in step 8, perform the following steps:

a. Turn off the system and attached peripherals, and disconnect the system from the electrical

outlet.

b. Open the system.

c. Reinstall one of the expansion cards.

d. Close the system.

e. Run the appropriate diagnostic test. For more information, see Using System Diagnostics .

Next steps

If the problem persists, see Getting Help.

Troubleshooting processors

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Steps

1. Run the appropriate diagnostics test. See Using System Diagnostics for available diagnostic tests.

2. Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

144

3. Open the system.

4. Ensure that the processor and heat sink are properly installed.

5. Close the system.

6. Run the appropriate diagnostic test. For more information, see Using System Diagnostics.

Next steps

If the problem persists, see Getting Help.

System messages

For a list of event and error messages generated by the system firmware and agents that monitor system

components, see the Dell Event and Error Messages Reference Guide at dell.com/esmmanuals.

Warning messages

A warning message alerts you to a possible problem and prompts you to respond before the system

continues a task. For example, before you format a hard drive, a message warns you that you may lose all

data on the hard drive. Warning messages usually interrupt the task and require you to respond by typing

y (yes) or n (no).

NOTE: Warning messages are generated by either the application or the operating system. For more

information, see the documentation that accompanied the operating system or application.

Diagnostic messages

The system diagnostic utilities may issue messages if you run diagnostic tests on your system. See Using

system diagnostics. for more information about system diagnostics.

Alert messages

The systems management software generates alert messages for your system. Alert messages include

information, status, warning, and failure messages for drive, temperature, fan, and power conditions. For

more information, see the systems management software documentation.

145

Using system diagnostics

If you experience a problem with your system, run the system diagnostics before contacting Dell for

technical assistance. The purpose of running system diagnostics is to test your system hardware without

requiring additional equipment or risking data loss. If you are unable to fix the problem yourself, service

and support personnel can use the diagnostics results to help you solve the problem.

Dell Embedded System Diagnostics

NOTE: The Dell Embedded System Diagnostics is also known as Enhanced Pre-boot System

Assessment (ePSA) diagnostics.

The embedded system diagnostics provides a set of options for particular device groups or devices

allowing you to:

• Run tests automatically or in an interactive mode

• Repeat tests

• Display or save test results

• Run thorough tests to introduce additional test options to provide extra information about the failed

device(s)

• View status messages that inform you if tests are completed successfully

• View error messages that inform you of problems encountered during testing

When to use the Embedded System Diagnostics

If a major component or device in the system does not operate properly, running the embedded system

diagnostics may indicate component failure.

Running the Embedded System Diagnostics from Boot Manager

1. As the system boots, press <F11>.

2. Use the up and down arrow keys to select System Utilities → Launch Diagnostics.

The ePSA Pre-boot System Assessment window is displayed, listing all devices detected in the

system. The diagnostics starts executing the tests on all the detected devices.

Running the Embedded System Diagnostics from the Dell Lifecycle

Controller

1. As the system boots, press <F11>.

2. Select Hardware Diagnostics → Run Hardware Diagnostics.

The ePSA Pre-boot System Assessment window is displayed, listing all devices detected in the

system. The diagnostics starts executing the tests on all the detected devices.

146

System diagnostic controls

Menu Description

Configuration Displays the configuration and status information of all detected devices.

Results Displays the results of all tests that are executed.

System health Provides the current overview of the system performance.

Event log Displays a time-stamped log of the results of all tests run on the system. This is

displayed if at least one event description is recorded.

For information about embedded system diagnostics, see the ePSA Diagnostics Guide (Notebooks,

Desktops and Servers) at dell.com/support/home.

147

Jumpers and connectors

System board jumper settings

For information about resetting the password jumper to disable a password, see Disabling a Forgotten

Password.

Table 21. System board jumper settings

Jumper Setting Description

PWRD_EN The password reset feature is enabled (pins 2–4).

The password reset feature is disabled (pins 4–6).

The iDRAC local access is unlocked at the next AC

power cycle.

NVRAM_CLR The configuration settings are retained at the next

system boot (pins 3–5).

The configuration settings are cleared at system

boot (pins 1–3).

148

System board connectors

Figure 60. System board jumpers and connectors

Table 22. System board jumpers and connectors

Item Connector Description

1 SYS_PWR_CONN (P1) 24-pin power connector

2 FB_USB Front-panel USB connector

3 PIB_CONN Power interposer board connector

4 SATA_CDROM SATA connector CDROM

5 MiniPERC PCIE_G3_X8 (CPU1) Mini PERC card connector

6 SATA_TBU SATA connector tape backup unit

7 SW_RAID_B Software RAID connector B

8 CTRL_PNL Control panel interface connector

9 SW_RAID_A Software RAID connector A

10 INT_USB_3.0 Internal USB connector

149

Item Connector Description

11 BATTERY Battery connector

12 TPM_MODULE Trusted platform module connector

13 J_PSWD_NVRAM For more information, see System board

jumper settings

14 SLOT3 PCIE_G3_X16(CPU1) PCIe card connector 3

15 SLOT2 PCIE_G3_X16(CPU1) PCIe card connector 2

NOTE: The PCIE_G3_X8 and

PCIE_G3_X16 are the two different

types of risers supported on R430

systems. You can install an expansion

card on the system board only using

expansion-card riser. Form more

information about the installation

guidelines, see Expansion card

installation guidelines.

16 NIC4 Network connector

17 NIC3 Network connector

18 B1, B2 Memory module socket

19 USB2_3.0 USB connector

20 USB1 USB connector

21 NIC1 and NIC2 Network connector

22 B3, B4 Memory module socket

23 CPU2 Processor socket 2

24 PWR_CONN_C(P3) 8-pin power connector

25 CPU1 Processor socket 1

26 IDSDM Internal Dual SD Module connector

27 INTRUSION Intrusion switch connector

28 FAN6 Cooling fan connector

29 A1, A5, A2, A6 Memory module socket

30 FAN5 Cooling fan connector

31 FAN4 Cooling fan connector

32 PWR_CONN_B(P2) 8-pin power connector

33 A3, A7, A4, A8 Memory module socket

34 FAN3 Cooling fan connector

35 FAN2 Cooling fan connector

150

Item Connector Description

36 BP_SIG Backplane signal connector

37 ODD_PWR Optical disk drive connector

Disabling a forgotten password

The system's software security features include a system password and a setup password. The password

jumper enables these password features or disables them and clears any password(s) currently in use.

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Steps

1. Turn off the system, including any attached peripherals, and disconnect the system from the

electrical outlet.

2. Open the system.

3. Move the jumper on the system-board jumper from pins 4 and 6 to pins 2 and 4.

4. Close the system.

The existing passwords are not disabled (erased) until the system boots with the jumper on pins 2

and 4. However, before you assign a new system and/or setup password, you must move the jumper

back to pins 4 and 6.

NOTE: If you assign a new system and/or setup password with the jumper on pins 2 and 4, the

system disables the new password(s) the next time it boots.

5. Reconnect the system to its electrical outlet and turn the system on, including any attached

peripherals.

6. Turn off the system, including any attached peripherals, and disconnect the system from the

electrical outlet.

7. Open the system.

8. Move the jumper on the system-board jumper from pins 2 and 4 to pins 4 and 6.

9. Close the system.

10. Reconnect the system to its electrical outlet and turn the system on, including any attached

peripherals.

11. Assign a new system and/or setup password.

151

Technical specifications

Table 23. Physical specifications

Physical

Height 42.8 mm (1.68 inch)

Width

With rack latches 482.4 mm (18.99 inch)

Without rack latches 434.0 mm (17.08 inch)

Depth (excludes bezel) 607.0 mm (23.9 inch)

Weight (maximum) 19.9 kg (43.87 lb)

Weight (empty) 16.73 kg (36.88 lb)

Table 24. Processor specification

Processor

Processor type Intel Xeon EP E5-2600 v3 product family

Table 25. Expansion Bus specifications

Expansion Bus

Bus type PCI Express Generation 2 and 3

Expansion slots using the expansion-card riser

PCIE_G3_X16 (Slot 1) one half-height, half-length x16 link for

processor 1

(Slot 2) one half-height, half-length x16 link for

processor 1

PCIE_G3_X8 (Slot 1) one Full-height, half-length x8 link for

processor 1

(Slot 2) one half-height, half-length x8 link for

processor 1

Table 26. Memory specifications

Memory

Architecture 1333 MT/s, 1600 MT/s, 1866 MT/s, or 2133 MT/s

DDR4 Registered DIMMs

152

Memory

Support for advanced ECC or memory optimized

operation

Memory module sockets Twelve 288-pin

Memory module capacities (RDIMMs) 4 GB (single-rank), 8 GB (single- and dual-rank),

16 GB (single- and dual-rank), and 32 GB (single-

and dual-rank)

Minimum RAM 4 GB with single processor

8 GB with dual processor

Maximum RAM Up to 192 GB with single processor

Up to 384 GB with dual processor

Table 27. Power specifications

Power

AC power supply (per power supply)

Wattage 450 W or 550 W

Power rating per power supply unit 550 W (Platinum) AC (100–240 V, 50/60 Hz, 7.4

A-3.7 A)

450 W (Bronze) AC (100–240 V, 50/60 Hz, 6.5

A-3.5 A)

Heat Dissipation

NOTE: Heat dissipation is calculated using the

power supply wattage rating.

2107 BTU/hr (550W power supply)

1871 BTU/hr (450W power supply)

Voltage

NOTE: This system is also designed to be

connected to IT power systems with a phase to

phase voltage not exceeding 230 V.

100-240 V AC, autoranging, 50/60 Hz

Table 28. RAID controller specification

RAID Controller

Controller type PERC 9

Table 29. Driver specifications

Drives

Hard drives

Four hard-drive systems Up to four 3.5-inch cabled hard drives, or

153

Drives

Up to four 3.5-inch hot-swappable SAS, SATA, or

Nearline SAS hard drives, or

Up to four 2.5-inch hot-swappable SAS, SATA,

SATA SSD, or Nearline SAS hard drives.

NOTE: Four hard-drive systems support

software RAID. For more information on

software RAID, see the Dell PowerEdge RAID

Controller (PERC) documentation at

dell.com/support/home.

Eight hard-drive systems Up to eight 2.5-inch, hot-swappable SAS, SATA,

SATA SSD, or Nearline SAS hard drives

Ten hard-drive systems Up to ten 2.5-inch, hot-swappable SATA HDD or

SATA SSD

Optical drive

Four hard-drive systems One optional slim SATA DV-DROM or DVD+/-RW

drive

NOTE: DVD devices are data only.

Eight hard-drive systems One optional ultra slim SATA DV-DROM or DVD

+/-RW drive

NOTE: DVD devices are data only.

Table 30. Connectors specifications

Connectors

Back

NIC Four 10/100/1000 Mbps

Serial 9-pin, DTE, 16550-compatible

USB One 9-pin, USB 3.0-compliant

One 4-pin, USB 2.0-compliant

Video 15-pin VGA

iDRAC8 One optional 1 GbE Ethernet

External vFlash card One optional vFlash memory card

NOTE: The card slot is available for use only if

the iDRAC8 Enterprise license is installed on

your system.

Front

USB Two 4-pin, USB 2.0-compliant

154

Connectors

Video 15-pin VGA

Internal

USB One 9-pin, USB 3.0-compliant

Internal Dual SD Module (IDSDM) Two optional flash memory card slots with the

internal SD module

NOTE: One card slot is dedicated for

redundancy.

Table 31. Video specifications

Video

Video type Integrated Matrox G200

Video memory 16 MB shared

Table 32. Environmental specifications

Environmental specifications

NOTE: For additional information about environmental measurements for specific system

configurations, see dell.com/environmental_datasheets.

Temperature

Storage –40°C to 65°C (–40°F to 149°F)

Continuous operation (for altitude less than 950

m or 3117 ft)

10°C to 35°C (50°F to 95°F) with no direct

sunlight on the equipment.

Fresh air For information on fresh air, see Expanded

Operating Temperature section.

Maximum temperature gradient (operating and

storage)

20°C/h (36°F/h)

Relative humidity

Storage 5% to 95% RH with 33°C (91°F) maximum dew

point. Atmosphere must be non-condensing at all

times.

Operating 10% to 80% Relative Humidity with 29°C (84.2°F)

maximum dew point.

Maximum vibration

Operating 0.26 Grms at 5 Hz to 350 Hz (all operation

orientations).

Storage 1.88 Grms at 10 Hz to 500 Hz for 15 min (all six

sides tested).

Maximum shock

155

Environmental specifications

Operating Six consecutively executed shock pulses in the

positive and negative x, y, and z axes of 40 G for

up to 2.3 ms.

Storage Six consecutively executed shock pulses in the

positive and negative x, y, and z axes (one pulse

on each side of the system) of 71 G for up to 2

ms.

Maximum altitude

Operating 3048 m (10,000 ft).

Storage 12,000 m (39,370 ft).

Operating temperature de-rating

Up to 35 °C (95 °F) Maximum temperature is reduced by 1°C/300 m

(1°F/547 ft) above 950 m (3,117 ft).

35 °C to 40 °C (95 °F to 104 °F) Maximum temperature is reduced by 1°C/175 m

(1°F/319 ft) above 950 m (3,117 ft).

40 °C to 45 °C (104 °F to 113 °F) Maximum temperature is reduced by 1°C/125 m

(1°F/228 ft) above 950 m (3,117 ft).

Particulate contamination

NOTE: This section defines the limits to help avoid IT equipment damage and/or failure from

particulates and gaseous contamination. If it is determined that levels of particulates or gaseous

pollution are beyond the limits specified below and are the reason for the damage and/or failures

to your equipment, it may be necessary for you to re-mediate the environmental conditions that

are causing the damage and/or failures. Re-mediation of environmental conditions will be the

responsibility of the customer.

Air filtration

NOTE: Applies to data center environments

only. Air filtration requirements do not

apply to IT equipment designed to be used

outside a data center, in environments such

as an office or factory floor.

Data center air filtration as defined by ISO Class 8

per ISO 14644-1 with a 95% upper confidence

limit.

NOTE: Air entering the data center must

have MERV11 or MERV13 filtration.

Conductive dust

NOTE: Applies to data center and non-data

center environments.

Air must be free of conductive dust, zinc whiskers,

or other conductive particles.

Corrosive dust

NOTE: Applies to data center and non-data

center environments.

• Air must be free of corrosive dust.

• Residual dust present in the air must have a

deliquescent point less than 60% relative

humidity.

Gaseous contamination

156

Environmental specifications

NOTE: Maximum corrosive contaminant levels measured at ≤50% relative humidity.

Copper coupon corrosion rate <300 Å/month per Class G1 as defined by ANSI/

ISA71.04-1985.

Silver coupon corrosion rate <200 Å/month as defined by AHSRAE TC9.9.

Table 33. Expanded operating temperature specifications

Expanded operating temperature

NOTE: When operating in the expanded temperature range, system performance may be impacted.

NOTE: When operating in the expanded temperature range, ambient temperature warnings may be

reported on the LCD and in the System Event Log.

< 10% of annual operating hours 5 °C to 40 °C at 5% to 85% RH with 26 °C dew

point.

NOTE: Outside the standard operating

temperature (10 °C to 35 °C), the system can

operate down to 5 °C or up to 40 °C for a

maximum of 10% of its annual operating

hours.

For temperatures between 35 °C and 40 °C, de-

rate maximum allowable dry bulb temperature by

1 °C per 175 m above 950 m (1 °F per 319 ft).

< 1% of annual operating hours –5 °C to 45 °C at 5% to 90% RH with 26 °C dew

point.

NOTE: Outside the standard operating

temperature (10 °C to 35 °C), the system can

operate down to –5 °C or up to 45 °C for a

maximum of 1% of its annual operating hours.

For temperatures between 40 °C and 45 °C, de-

rate maximum allowable dry bulb temperature by

1 °C per 125 m above 950 m (1 °F per 228 ft).

Expanded Operating Temperature Restrictions • Processors of 55 W and 65 W are not

supported.

• Do not perform a cold startup below 5 °C.

• Allow processor performance degrade.

• Non-redundant power supplies are not

supported.

• Non Dell qualified peripheral cards and/or

peripheral cards are not supported.

• Maximum altitude for the operating

temperature must be 3050 m (10,000 ft).

157

Getting help

Contacting Dell

Dell provides several online and telephone-based support and service options. If you do not have an

active Internet connection, you can find contact information on your purchase invoice, packing slip, bill,

or Dell product catalog. Availability varies by country and product, and some services may not be

available in your area. To contact Dell for sales, technical support, or customer-service issues:

1. Go to dell.com/support.

2. Select your country from the drop-down menu on the bottom right corner of the page.

3. For customized support:

a. Enter your system Service Tag in the Enter your Service Tag field.

b. Click Submit.

The support page that lists the various support categories is displayed.

4. For general support:

a. Select your product category.

b. Select your product segment.

c. Select your product.

The support page that lists the various support categories is displayed.

Locating your system Service Tag

Your system is identified by a unique Express Service Code and Service Tag number. The Express Service

Code and Service Tag are found on the front of the system by pulling out the information tag.

Alternatively, the information may be on a sticker on the chassis of the system. This information is used

by Dell to route support calls to the appropriate personnel.

Documentation feedback

If you have feedback for this document, write to documentation_feedback@dell.com. Alternatively, you

can click on the Feedback link in any of the Dell documentation pages, fill out the form, and click Submit

to send your feedback.

Quick Resource Locator (QRL)

Use the Quick Resource Locator (QRL) to get immediate access to system information and how-to

videos. This can be done by visiting dell.com/QRL or by using your smartphone or tablet and a model

specific Quick Resource (QR) code located on your Dell PowerEdge system. To try out the QR code, scan

the following image.

158

Figure 61. Quick Resource Locator

159

Table of Contents

DELL R430 User Manual

Related Manuals