Table of Contents
- About Your System
- Using the System Setup Program and UEFI Boot Manager
- Installing System Components
- Recommended Tools
- Inside the System
- Opening and Closing the System
- Front Bezel
- EMI Filler Panel
- Optical and Tape Drives (Optional)
- Hard Drives
- Expansion-Card Stabilizer
- Cooling Shroud
- Expansion Cards
- System Memory
- Processor
- Cooling Fan
- System Battery
- Power Supply
- Internal USB Memory Key
- Chassis Intrusion Switch
- Control Panel Assembly
- System Board
- Troubleshooting Your System
- Safety First-For You and Your System
- Troubleshooting System Startup Failure
- Troubleshooting External Connections
- Troubleshooting the Video Subsystem
- Troubleshooting a USB Device
- Troubleshooting a Serial I/O Device
- Troubleshooting a NIC
- Troubleshooting a Wet System
- Troubleshooting a Damaged System
- Troubleshooting the System Battery
- Troubleshooting Power Supply
- Troubleshooting System Cooling Problems
- Troubleshooting Cooling Fan
- Troubleshooting System Memory
- Troubleshooting an Internal USB Key
- Troubleshooting an Optical Drive
- Troubleshooting a Tape Backup Unit
- Troubleshooting a Hard Drive
- Troubleshooting Expansion Cards
- Troubleshooting the Processor
- Running the System Diagnostics
- Jumpers and Connectors
- Getting Help
- Index
DELL T110 II User Manual
Displayed below is the user manual for T110 II by DELL which is a product in the Servers category. This manual has pages.
Related Manuals
Dell PowerEdge T110 II
Systems
Owner’s Manual
Regulatory Model E11S Series
Regulatory Type E11S002
Coaster_HOM.book Page 1 Monday, November 3, 2014 3:23 PM
Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make better use of
your computer.
CAUTION: A CAUTION indicates potential damage to hardware or loss of data if
instructions are not followed.
WARNING: A WARNING indicates a potential for property damage, personal
injury, or death.
____________________
Information in this publication is subject to change without notice.
© 2014 Dell Inc. All rights reserved.
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.
is strictly forbidden.
T rademarks used in this text: Dell™, the DELL logo, PowerEdge™ are trademarks of Dell Inc.
Microsoft®, Windows®, and Windows Server® are either trademarks or registered trademarks of
Microsoft Corporation in the United States and/or other countries.
Other trademarks and trade names may be used in this publication to refer to either the entities claiming
the marks and names or their products. Dell Inc. dis claims any proprietary interest in trademarks and
trade names other than its own.
October 2014 Rev. A01
Coaster_HOM.book Page 2 Monday, November 3, 2014 3:23 PM
Contents 3
Contents
1 About Your System. . . . . . . . . . . . . . . . . . 11
Accessing System Features During Startup. . . . . . . 11
Front-Panel Features and Indicators . . . . . . . . . . 12
Back-Panel Features and Indicators . . . . . . . . . . 14
Guidelines for Connecting External Devices . . . . . . 15
NIC Indicator Codes . . . . . . . . . . . . . . . . . . . 16
Diagnostic Lights . . . . . . . . . . . . . . . . . . . . 17
System Messages . . . . . . . . . . . . . . . . . . . . 19
Warning Messages . . . . . . . . . . . . . . . . . . . 32
Diagnostics Messages . . . . . . . . . . . . . . . . . 32
Alert Messages . . . . . . . . . . . . . . . . . . . . . 32
Other Information You May Need . . . . . . . . . . . . 32
2 Using the System Setup Program and UEFI Boot
Manager . . . . . . . . . . . . . . . . . . . . . . . . . 35
Choosing the System Boot Mode . . . . . . . . . . . . 35
Entering the System Setup Program. . . . . . . . . . . 36
Responding to Error Messages. . . . . . . . . . . 36
Using the System Setup Program Navigation Keys 36
Coaster_HOM.book Page 3 Monday, November 3, 2014 3:23 PM
4Contents
System Setup Options . . . . . . . . . . . . . . . . . . 37
Main Screen . . . . . . . . . . . . . . . . . . . . 37
Memory Settings Screen . . . . . . . . . . . . . . 39
Processor Settings Screen . . . . . . . . . . . . . 39
SATA Settings Screen. . . . . . . . . . . . . . . . 40
Boot Settings Screen . . . . . . . . . . . . . . . . 41
Integrated Devices Screen . . . . . . . . . . . . . 41
PCI IRQ Assignments Screen . . . . . . . . . . . . 42
Serial Communication Screen . . . . . . . . . . . 43
Power Management Screen . . . . . . . . . . . . 44
System Security Screen . . . . . . . . . . . . . . 45
Exit Screen . . . . . . . . . . . . . . . . . . . . . 47
Entering the UEFI Boot Manager. . . . . . . . . . . . . 47
Using the UEFI Boot Manager Navigation Keys . . 47
UEFI Boot Manager Screen. . . . . . . . . . . . . 48
UEFI Boot Settings Screen . . . . . . . . . . . . . 48
System Utilities Screen . . . . . . . . . . . . . . . 49
System and Setup Password Features. . . . . . . . . . 49
Using the System Password . . . . . . . . . . . . 49
Using the Setup Password . . . . . . . . . . . . . 52
Embedded System Management. . . . . . . . . . . . . 53
Baseboard Management Controller Configuration . . . 53
Entering the BMC Setup Module . . . . . . . . . . 54
iDRAC Configuration Utility . . . . . . . . . . . . . . . 54
Entering the iDRAC Configuration Utility . . . . . . 55
3 Installing System Components . . . . . . . 57
Recommended Tools . . . . . . . . . . . . . . . . . . . 57
Coaster_HOM.book Page 4 Monday, November 3, 2014 3:23 PM
Contents 5
Inside the System . . . . . . . . . . . . . . . . . . . . 58
Opening and Closing the System . . . . . . . . . . . . 59
Opening the System . . . . . . . . . . . . . . . . 59
Closing the System . . . . . . . . . . . . . . . . . 60
Front Bezel . . . . . . . . . . . . . . . . . . . . . . . . 61
Removing the Front Bezel . . . . . . . . . . . . . 61
Installing the Front Bezel . . . . . . . . . . . . . . 62
Removing Front Bezel Insert . . . . . . . . . . . . 62
Installing Front Bezel Insert . . . . . . . . . . . . 63
EMI Filler Panel . . . . . . . . . . . . . . . . . . . . . 63
Removing an EMI Filler Panel . . . . . . . . . . . 63
Installing an EMI Filler Panel . . . . . . . . . . . . 64
Optical and Tape Drives (Optional) . . . . . . . . . . . 65
Removing an Optical or Tape Drive. . . . . . . . . 65
Installing an Optical or Tape Drive . . . . . . . . . 68
Hard Drives. . . . . . . . . . . . . . . . . . . . . . . . 70
Hard Drive Installation Guidelines . . . . . . . . . 70
Removing a 3.5-Inch Hard Drive . . . . . . . . . . 70
Installing a 3.5-Inch Hard Drive. . . . . . . . . . . 72
Removing a 3.5-Inch Hard Drive From a Hard-Drive Bracket 74
Removing a 2.5-Inch Hard Drive . . . . . . . . . . 74
Installing a 2.5-Inch Hard Drive. . . . . . . . . . . 76
Expansion-Card Stabilizer. . . . . . . . . . . . . . . . 78
Removing the Expansion-Card Stabilizer. . . . . . 78
Installing the Expansion-Card Stabilizer . . . . . . 78
Cooling Shroud. . . . . . . . . . . . . . . . . . . . . . 78
Removing the Cooling Shroud . . . . . . . . . . . 79
Installing the Cooling Shroud. . . . . . . . . . . . 80
Coaster_HOM.book Page 5 Monday, November 3, 2014 3:23 PM
6Contents
Expansion Cards . . . . . . . . . . . . . . . . . . . . . 81
Expansion Card Installation Guidelines. . . . . . . 81
Removing an Expansion Card. . . . . . . . . . . . 82
Installing an Expansion Card . . . . . . . . . . . . 84
SAS Controller Expansion Card. . . . . . . . . . . 85
System Memory . . . . . . . . . . . . . . . . . . . . . 86
General Memory Module Installation Guidelines . 86
Mode-Specific Guidelines . . . . . . . . . . . . . 86
Removing Memory Modules . . . . . . . . . . . . 88
Installing Memory Modules. . . . . . . . . . . . . 89
Processor. . . . . . . . . . . . . . . . . . . . . . . . . 91
Removing the Processor . . . . . . . . . . . . . . 91
Installing a Processor. . . . . . . . . . . . . . . . 94
Cooling Fan. . . . . . . . . . . . . . . . . . . . . . . . 95
Removing the Cooling Fan . . . . . . . . . . . . . 95
Installing the Cooling Fan . . . . . . . . . . . . . . 96
System Battery . . . . . . . . . . . . . . . . . . . . . . 97
Replacing the System Battery . . . . . . . . . . . 97
Power Supply . . . . . . . . . . . . . . . . . . . . . . 99
Removing the Power Supply . . . . . . . . . . . . 99
Installing the Power Supply. . . . . . . . . . . . 100
Internal USB Memory Key . . . . . . . . . . . . . . . 101
Chassis Intrusion Switch . . . . . . . . . . . . . . . 102
Removing the Chassis Intrusion Switch . . . . . 102
Installing the Chassis Intrusion Switch. . . . . . 103
Control Panel Assembly . . . . . . . . . . . . . . . . 104
Removing the Control Panel Assembly . . . . . . 104
Installing the Control Panel Assembly . . . . . . 106
Coaster_HOM.book Page 6 Monday, November 3, 2014 3:23 PM
Contents 7
System Board . . . . . . . . . . . . . . . . . . . . . . 107
Removing the System Board . . . . . . . . . . . . 107
Installing the System Board . . . . . . . . . . . . 109
4 Troubleshooting Your System . . . . . . . . 111
Safety First—For You and Your System . . . . . . . . . 111
Troubleshooting System Startup Failure . . . . . . . . 111
Troubleshooting External Connections . . . . . . . . . 111
Troubleshooting the Video Subsystem . . . . . . . . . 112
Troubleshooting a USB Device . . . . . . . . . . . . . 112
Troubleshooting a Serial I/O Device . . . . . . . . . . 113
Troubleshooting a NIC . . . . . . . . . . . . . . . . . . 113
Troubleshooting a Wet System . . . . . . . . . . . . . 114
Troubleshooting a Damaged System . . . . . . . . . . 115
Troubleshooting the System Battery. . . . . . . . . . . 116
Troubleshooting Power Supply . . . . . . . . . . . . . 117
Troubleshooting System Cooling Problems . . . . . . . 117
Troubleshooting Cooling Fan . . . . . . . . . . . . . . 118
Troubleshooting System Memory . . . . . . . . . . . . 119
Troubleshooting an Internal USB Key . . . . . . . . . . 120
Troubleshooting an Optical Drive . . . . . . . . . . . . 121
Troubleshooting a Tape Backup Unit . . . . . . . . . . 122
Coaster_HOM.book Page 7 Monday, November 3, 2014 3:23 PM
8Contents
Troubleshooting a Hard Drive . . . . . . . . . . . . . 123
Troubleshooting Expansion Cards . . . . . . . . . . . 124
Troubleshooting the Processor . . . . . . . . . . . . 125
5 Running the System Diagnostics . . . . . . 127
Using Online Diagnostics . . . . . . . . . . . . . . . 127
Embedded System Diagnostics Features . . . . . . . 127
When to Use the Embedded System Diagnostics . . . 128
Running the Embedded System Diagnostics . . . . . 128
System Diagnostics Testing Options. . . . . . . . . . 128
Using the Custom Test Options . . . . . . . . . . . . 129
Selecting Devices for Testing. . . . . . . . . . . 129
Selecting Diagnostics Options . . . . . . . . . . 129
Viewing Information and Results . . . . . . . . . 130
6 Jumpers and Connectors. . . . . . . . . . . . 131
System Board Jumper . . . . . . . . . . . . . . . . . 131
System Board Connectors . . . . . . . . . . . . . . . 132
Disabling a Forgotten Password. . . . . . . . . . . . 134
7 Getting Help . . . . . . . . . . . . . . . . . . . . . . 135
Contacting Dell. . . . . . . . . . . . . . . . . . . . . 135
Coaster_HOM.book Page 8 Monday, November 3, 2014 3:23 PM
10 Contents
Coaster_HOM.book Page 10 Monday, November 3, 2014 3:23 PM
About Your System 11
1
About Your System
Accessing System Features During Startup
The following keystrokes provide access to system features during startup:
Keystroke Description
<F2> Enters the System Setup program. See "Using the System Setup
Program and UEFI Boot Manager" on page 35.
<F10> Enters System Services, which opens the Dell Unified Server
Configurator (USC). The Dell USC allows you to access utilities
such as embedded system diagnostics. For more information, see
the Dell USC documentation.
<F11> Enters the BIOS Boot Manager or the
Unified Extensible
Firmware Interface (
UEFI) Boot Manager, depending on the
system's boot configuration. See "Using the System Setup Program
and UEFI Boot Manager" on page 35.
<F12> Starts Preboot eXecution Environment (PXE) boot.
<Ctrl><E> Enters the Baseboard Management Controller (BMC)
Configuration Utility, which allows access to the System Event Log
(SEL) and configuration of remote access to the system. For more
information, see the BMC user documentation.
<Ctrl><C> Enters the SAS Configuration Utility. For more information, see
the SAS adapter documentation.
<Ctrl><R> Enters the PERC configuration utility. For more information, see
the PERC card documentation.
<Ctrl><S> Enters the utility to configure NIC settings for PXE boot. For more
information, see the documentation for your integrated NIC.
Coaster_HOM.book Page 11 Monday, November 3, 2014 3:23 PM
12 About Your System
Front-Panel Features and Indicators
Figure 1-1. Front-Panel Features and Indicators
Item Indicator, Button, or
Connector
Icon Description
1Power-on indicator,
power button
The power-on indicator lights when the
system power is on.
The power button controls the DC
power supply output to the system.
NOTE: When powering on the system, the
video monitor can take from several
seconds to over 2 minutes to display an
image, depending on the amount of
memory installed in the system.
NOTE: On ACPI-compliant operating
systems, turning off the system using the
power button causes the system to
perform a graceful shutdown before
power to the system is turned off.
1
5
23
4
7
6
Coaster_HOM.book Page 12 Monday, November 3, 2014 3:23 PM
About Your System 13
2 System health
indicator
The system health indicator blinks
amber when a system fault is detected.
3 Hard-drive activity
indicator
The hard drive activity indicator lights
up when the hard drive is in use.
4 USB connectors (2) Connect USB devices to the system. The
ports are USB 2.0-compliant.
5 Diagnostic indicator
lights (4)
The four diagnostic indicator lights
display error codes during system
startup. See "Diagnostic Lights" on
page 17.
6 Tape drive (optional) One optional half-height (using one
drive bay).
7 Optical drive
(optional)
One optional SATA DVD-ROM drive or
DVD+/-RW drive.
NOTE: DVD devices are data only.
Item Indicator, Button, or
Connector
Icon Description
Coaster_HOM.book Page 13 Monday, November 3, 2014 3:23 PM
14 About Your System
Back-Panel Features and Indicators
Figure 1-2. Back-Panel Features and Indicators
Item Indicator, Button, or
Connector
Icon Description
1 Padlock ring Locks the cover release latch.
2 Security cable slot Connects a cable lock to the system.
3Voltage selection
switch
Sets the voltage for the power supply to
the voltage that most closely matches
the AC power available at your location.
8
9
7
6
10
1
4
11
2
3
5
Coaster_HOM.book Page 14 Monday, November 3, 2014 3:23 PM
About Your System 15
Guidelines for Connecting External Devices
• Turn off power to the system and external devices before attaching a new
external device. Turn on any external devices before turning on the system
(unless the documentation for the device specifies otherwise).
• Ensure that the appropriate driver for the attached device has been
installed on the system.
• If necessary to enable ports on your system, use the System Setup program.
See "Using the System Setup Program and UEFI Boot Manager" on
page 35.
4 Power supply 305 W power supply.
5 Cable clasp Secures the power cable.
6 USB connectors (4) Connect USB devices to the system. The
ports are USB 2.0-compliant.
7 eSATA connector Connects additional storage devices.
8 Serial connector Connects a serial device to the system.
9 Video connector Connects a VGA display to the system.
10 Ethernet connector Integrated 10/100/1000 NIC connector.
11 PCIe expansion card
slots (4)
Connects up to four PCI Express
expansion cards.
Item Indicator, Button, or
Connector
Icon Description
Coaster_HOM.book Page 15 Monday, November 3, 2014 3:23 PM
16 About Your System
NIC Indicator Codes
Figure 1-3. NIC Indicator Codes
1 link indicator 2 activity indicator
Indicator Indicator Code
Link and activity indicators
are off
The NIC is not connected to the network.
Link indicator is green The NIC is connected to a valid network link at
1000 Mbps.
Link indicator is amber The NIC is connected to a valid network link at
10/100 Mbps.
Activity indicator is green
blinking
Network data is being sent or received.
12
Coaster_HOM.book Page 16 Monday, November 3, 2014 3:23 PM
About Your System 17
Diagnostic Lights
The four diagnostic indicator lights on the system front panel display error
codes during system startup. Table 1-1 lists the causes and possible corrective
actions associated with these codes. A highlighted circle indicates the light is
on; a non-highlighted circle indicates the light is off.
Table 1-1. Diagnostic Indicator Code
Code Causes Corrective Action
The system is in a normal
off condition or a possible
pre-BIOS failure has
occurred.
The diagnostic lights are
not lit after the system
successfully boots to the
operating system.
Plug the system into a working
electrical outlet and press the
power button.
The system is in a normal
operating condition after
POST.
Information only.
BIOS checksum failure
detected; system is in
recovery mode.
See "Getting Help" on page 135.
Possible processor failure. See "Troubleshooting the
Processor" on page 125.
Memory failure. See "Troubleshooting System
Memory" on page 119.
Possible expansion card
failure.
See "Troubleshooting Expansion
Cards" on page 124.
Possible video failure. See "Getting Help" on page 135.
Coaster_HOM.book Page 17 Monday, November 3, 2014 3:23 PM
18 About Your System
Hard drive failure. Ensure that the hard drives are
properly connected. See "Hard
Drives" on page 70 for
information on the drives
installed in your system.
Possible USB failure. See "Troubleshooting a USB
Device" on page 112.
No memory modules
detected.
See "Troubleshooting System
Memory" on page 119.
System board failure. See "Getting Help" on page 135.
Memory configuration
error.
See "Troubleshooting System
Memory" on page 119.
Possible system board
resource and/or system
board hardware failure.
See "Getting Help" on page 135.
Possible system resource
configuration error.
See "Getting Help" on page 135.
Other failure. Ensure that the optical drive and
hard drives are properly
connected. See "Troubleshooting
Your System" on page 111 for the
appropriate drive installed in your
system. If the problem persists,
see "Getting Help" on page 135.
Code Causes Corrective Action
Coaster_HOM.book Page 18 Monday, November 3, 2014 3:23 PM
About Your System 19
System Messages
System messages appear on the screen to notify you of a possible problem
with the system.
NOTE: If you receive a system message not listed in the table, check the
documentation for the application that is running when the message appears or the
operating system's documentation for an explanation of the message and
recommended action.
Message Causes Corrective Actions
Alert! BMC not
responding.
Rebooting.
The BMC is not
responding to BIOS
communication either
because it is not
functioning properly or has
not completed
initialization. The system
reboots.
Wait for the system to reboot.
Alert! BMC not
responding.
Power required
may exceed PSU
wattage.
Alert!
Continuing
system boot
accepts the risk
that system may
power down
without warning.
The BMC is hung.
The BMC was remotely
reset while system was
booting.
After AC recovery, the
BMC takes longer than
normal to boot.
Remove AC power to the
system for 10 seconds and
restart the system.
Coaster_HOM.book Page 19 Monday, November 3, 2014 3:23 PM
20 About Your System
Alert! Power
required exceeds
PSU wattage.
Check PSU and
system
configuration.
Alert!
Continuing
system boot
accepts the risk
that system may
power down
without warning.
The system configuration
of processor, memory
modules, and expansion
cards may not be supported
by the power supply.
If any system components
were just upgraded, return the
system to the previous
configuration. If the system
boots without this warning,
then the replaced
component(s) are not
supported with this power
supply. See "Power Supply" on
page 99.
Alert! System
fatal error
during previous
boot.
An error caused the system
to reboot.
Check other system messages
for additional information for
possible causes.
BIOS
MANUFACTURING
MODE detected.
MANUFACTURING
MODE will be
cleared before
the next boot.
System reboot
required for
normal
operation.
System is in manufacturing
mode.
Reboot to take the system out
of manufacturing mode.
BIOS Update
Attempt Failed!
Remote BIOS update
attempt failed.
Retry the BIOS update. If
problem persists, see "Getting
Help" on page 135.
Message Causes Corrective Actions
Coaster_HOM.book Page 20 Monday, November 3, 2014 3:23 PM
About Your System 21
Caution!
NVRAM_CLR jumper
is installed on
system
board.Please run
SETUP.
NVRAM_CLR jumper is
installed in the clear
setting. CMOS has been
cleared.
Move the NVRAM_CLR
jumper to the default position
(pins 3 and 5). See Figure 6-1
for jumper location. Restart
the system and re-enter the
BIOS settings. See "Using the
System Setup Program and
UEFI Boot Manager" on
page 35.
CPU set to
minimum
frequency.
The processor speed may
be intentionally set lower
for power conservation.
If not an intentional setting,
check other system messages
for possible causes.
Current boot mode
is set to UEFI.
Please ensure
compatible
bootable media is
available. Use
the system setup
program to change
the boot mode as
needed.
The system failed to boot
because UEFI boot mode is
enabled in BIOS and the
boot operating system is
non-UEFI.
Ensure that the boot mode is
set correctly and that the
proper bootable media is
available. See "Using the
System Setup Program and
UEFI Boot Manager" on
page 35.
Decreasing
available
memory.
Faulty or improperly
installed memory modules.
Reseat the memory modules.
See "Troubleshooting System
Memory" on page 119.
Embedded NICx and
NICy:
OS NIC=<ENABLED
|DISABLED>,
Management
Shared NIC=
<ENABLED
|DISABLED>
The operating system NIC
interface is set in BIOS.
The Management Shared
NIC interface is set in
management tools.
Check the system
management software or the
System Setup program for
NIC settings. If a problem is
indicated, see
"Troubleshooting a NIC" on
page 113.
Message Causes Corrective Actions
Coaster_HOM.book Page 21 Monday, November 3, 2014 3:23 PM
22 About Your System
Error 8602 -
Auxiliary Device
Failure. Verify
that mouse and
keyboard are
securely
attached to
correct
connectors.
Mouse or keyboard cable is
loose or improperly
connected.
Reseat the mouse or keyboard
cable.
Defective mouse or
keyboard.
Ensure that the mouse or
keyboard is operational. See
"Troubleshooting a USB
Device" on page 112.
Gate A20 failure. Faulty keyboard controller;
faulty system board.
See "Getting Help" on
page 135.
General failure. The operating system is
unable to carry out the
command.
This message is usually
followed by specific
information. Note the
information, and take the
appropriate action to resolve
the problem.
Invalid
configuration
information -
please run SETUP
program.
An invalid system
configuration caused a
system to halt.
Run the System Setup
program and review the
current settings. See "Using
the System Setup Program and
UEFI Boot Manager" on
page 35.
Keyboard
controller
failure.
Faulty keyboard controller;
faulty system board.
See "Getting Help" on
page 135.
Keyboard data
line failure.
Keyboard stuck
key failure.
Keyboard cable connector
is improperly connected or
the keyboard is defective.
Reseat the keyboard cable. If
the problem persists, see
"Troubleshooting a USB
Device" on page 112.
Keyboard fuse has
failed.
Overcurrent detected at
the keyboard connector.
See "Getting Help" on
page 135.
Message Causes Corrective Actions
Coaster_HOM.book Page 22 Monday, November 3, 2014 3:23 PM
About Your System 23
Local keyboard
may not work
because all user
accessible USB
ports are
disabled. If
operating
locally, power
cycle the system
and enter system
setup program to
change settings.
The USB ports are disabled
in the system BIOS.
Power down and restart the
system from the power button,
and then enter the System
Setup program to enable the
USB port(s). See "Entering the
System Setup Program" on
page 36.
Manufacturing
mode detected.
System is in manufacturing
mode.
Reboot to take the system out
of manufacturing mode.
Maximum rank
count exceeded.
The following
DIMM has been
disabled: x
Invalid memory
configuration. The system
will run but with the
specified memory module
disabled.
Ensure that the memory
modules are installed in a valid
configuration. See "General
Memory Module Installation
Guidelines" on page 86.
Memory address
line failure at
address, read
value expecting
value.
Faulty or improperly
installed memory modules.
See "Troubleshooting System
Memory" on page 119.
Memory double
word logic
failure at
address, read
value expecting
value.
Faulty or improperly
installed memory modules.
See "Troubleshooting System
Memory" on page 119.
Memory
Initialization
Warning: Memory
size may be
reduced.
Invalid memory
configuration. The system
will run but with less
memory than is physically
available.
Ensure that the memory
modules are installed in a valid
configuration. See "General
Memory Module Installation
Guidelines" on page 86.
Message Causes Corrective Actions
Coaster_HOM.book Page 23 Monday, November 3, 2014 3:23 PM
24 About Your System
Memory odd/even
logic failure at
address, read
value expecting
value.
Faulty or improperly
installed memory modules.
See "Troubleshooting System
Memory" on page 119.
Memory
write/read
failure at
address, read
value expecting
value.
Faulty or improperly
installed memory modules.
See "Troubleshooting System
Memory" on page 119.
Memory set to
minimum
frequency.
The memory frequency
may be intentionally set
lower for power
conservation.
If not an intentional setting,
check any other system
messages for possible causes.
The current memory
configuration may support
only the minimum
frequency.
Ensure that your memory
configuration supports the
higher frequency. See "General
Memory Module Installation
Guidelines" on page 86.
Memory tests
terminated by
keystroke.
POST memory test was
terminated by pressing the
spacebar.
Information only.
MEMTEST lane
failure
detected on x.
Invalid memory
configuration. A
mismatched memory
module is installed.
Ensure that the memory
modules are installed in a valid
configuration. See "General
Memory Module Installation
Guidelines" on page 86.
Message Causes Corrective Actions
Coaster_HOM.book Page 24 Monday, November 3, 2014 3:23 PM
About Your System 25
No boot device
available.
Faulty or missing optical
drive subsystem, hard drive,
or hard-drive subsystem, or
no bootable USB key
installed.
Use a bootable USB key, CD,
or hard drive. If the problem
persists, see "Troubleshooting
a USB Device" on page 112,
"Troubleshooting an Optical
Drive" on page 121, and
"Troubleshooting a Hard
Drive" on page 123. See "Using
the System Setup Program and
UEFI Boot Manager" on
page 35 for information on
setting the order of boot
devices.
No boot sector on
hard drive.
Incorrect configuration
settings in System Setup
program, or no operating
system on hard drive.
Check the hard-drive
configuration settings in the
System Setup program. See
"Using the System Setup
Program and UEFI Boot
Manager" on page 35. If
necessary, install the operating
system on your hard drive. See
your operating system
documentation.
No timer tick
interrupt.
Faulty system board. See "Getting Help" on
page 135.
PCI BIOS failed
to install.
PCIe device BIOS (Option
ROM) checksum failure
detected during shadowing.
Cables to expansion card(s)
loose; faulty or improperly
installed expansion card(s).
Reseat the expansion card(s).
Ensure that all appropriate
cables are securely connected
to the expansion card(s). If the
problem persists, see
"Troubleshooting Expansion
Cards" on page 124.
PCIe Training
Error: Expected
Link Width is x,
Actual Link Width
is y.
Faulty or improperly
installed PCIe card in the
specified slot.
Reseat the PCIe card in the
specified slot number. See
"Troubleshooting Expansion
Cards" on page 124. If the
problem persists, see "Getting
Help" on page 135.
Message Causes Corrective Actions
Coaster_HOM.book Page 25 Monday, November 3, 2014 3:23 PM
26 About Your System
Plug & Play
Configuration
Error.
Error encountered in
initializing PCIe device;
faulty system board.
Install the NVRAM_CLR
jumper in the clear position
(pins 1 and 3) and reboot the
system. See Figure 6-1 for
jumper location. If the
problem persists, see
"Troubleshooting Expansion
Cards" on page 124.
Quad rank DIMM
detected after
single rank or
dual rank DIMM in
socket.
Invalid memory
configuration.
Ensure that the memory
modules are installed in a valid
configuration. See "General
Memory Module Installation
Guidelines" on page 86.
Read fault.
Requested sector
not found.
The operating system
cannot read from the hard
drive, optical drive, or USB
device; the system could
not find a particular sector
on the disk, or the
requested sector is
defective.
Replace the optical medium,
USB medium or device.
Ensure that the USB or SATA
cables are properly connected.
See "Troubleshooting a USB
Device" on page 112,
"Troubleshooting an Optical
Drive" on page 121, and
"Troubleshooting a Hard
Drive" on page 123 for the
appropriate drive(s) installed
in your system.
SATA Port x
device not found.
There is no device
connected to the specified
SATA port.
Information only.
SATA port x
device auto-
sensing error.
SATA port x
device
configuration
error.
SATA port x
device error.
The drive connected to the
specified SATA port is
faulty.
Replace the faulty drive.
Message Causes Corrective Actions
Coaster_HOM.book Page 26 Monday, November 3, 2014 3:23 PM
About Your System 27
Sector not found.
Seek error.
Seek operation
failed.
Faulty hard drive, USB
device or medium.
Replace the USB medium or
device. Ensure that the USB
cables are properly connected.
See "Troubleshooting a USB
Device" on page 112 or
"Troubleshooting a Hard
Drive" on page 123 for the
appropriate drive(s) installed
in your system.
Shutdown
failure.
General system error. See "Getting Help" on
page 135.
The amount of
system memory has
changed.
Memory has been added or
removed or a memory
module may be faulty.
If memory has been added or
removed, this message is
informative and can be
ignored. If memory has not
been added or removed, check
the SEL to determine if single-
bit or multi-bit errors were
detected and replace the faulty
memory module. See
"Troubleshooting System
Memory" on page 119.
Message Causes Corrective Actions
Coaster_HOM.book Page 27 Monday, November 3, 2014 3:23 PM
28 About Your System
The following
DIMMs should
match in
geometry:
x,x,...
Invalid memory
configuration. The
specified memory modules
do not match in size,
number of ranks, or
number of data lanes.
Ensure that the memory
modules are installed in a valid
configuration. See "General
Memory Module Installation
Guidelines" on page 86.
The following
DIMMs should
match in rank
count: x,x,...
The following
DIMMs should
match in size:
x,x,...
The following
DIMMs should
match in size
and geometry:
x,x,...
The following
DIMMs should
match in size
and rank count:
x,x,...
Thermal sensor
not detected on
x.
A memory module without
a thermal sensor is installed
in the specified memory
slot.
Replace the memory module.
See "System Memory" on
page 86.
Time-of-day
clock stopped.
Faulty battery or faulty
chip.
See "Troubleshooting the
System Battery" on page 116.
Time-of-day not
set - please run
SETUP program.
Incorrect Time or Date
settings; faulty system
battery.
Check the Time and Date
settings. See "Using the
System Setup Program and
UEFI Boot Manager" on
page 35. If the problem
persists, replace the system
battery. See "System Battery"
on page 97.
Message Causes Corrective Actions
Coaster_HOM.book Page 28 Monday, November 3, 2014 3:23 PM
About Your System 29
Timer chip
counter 2 failed.
Faulty system board. See "Getting Help" on
page 135.
TPM
configuration
operation
honored. System
will now reset.
A Trusted Platform Module
(TPM) configuration
command has been
entered. The system will
reboot and execute the
command.
Information only.
TPM
configuration
operation is
pending. Press
(I) to Ignore OR
(M) to Modify to
allow this change
and reset the
system.
WARNING:
Modifying could
prevent
security.
This message displays
during system restart after
a TPM configuration
command has been
entered. User interaction is
required to proceed.
Enter I or M to proceed.
TPM failure. A TPM function has failed. See "Getting Help" on
page 135.
Unable to launch
System Services
image. System
halted!
System halted after F10
keystroke because System
Services image is either
corrupted in the system
firmware or has been lost
due to system board
replacement.
Restart the system and update
the Dell USC repository to the
latest software to restore full
functionality. See the Dell
USC user documentation for
more information.
Unexpected
interrupt in
protected mode.
Improperly seated memory
modules or faulty keyboard
or mouse controller chip.
Reseat the memory modules.
See "Troubleshooting System
Memory" on page 119. If the
problem persists, see "Getting
Help" on page 135.
Message Causes Corrective Actions
Coaster_HOM.book Page 29 Monday, November 3, 2014 3:23 PM
30 About Your System
Unsupported DIMM
detected. The
following DIMM
has been
disabled: x
Invalid memory
configuration. The system
will run but with the
specified memory module
disabled.
Ensure that the memory
modules are installed in a valid
configuration. See "General
Memory Module Installation
Guidelines" on page 86.
Unsupported
memory
configuration.
DIMM mismatch
across slots
detected:
x,x,...
Invalid memory
configuration. Memory
modules are mismatched in
the specified slots.
Ensure that the memory
modules are installed in a valid
configuration. See "General
Memory Module Installation
Guidelines" on page 86.
Warning: A fatal
error has caused
system reset!
Please check the
system event log!
A fatal system error
occurred and caused the
system to reboot.
Check the SEL for
information that was logged
during the error. See the
applicable troubleshooting
section in "Troubleshooting
Your System" on page 111 for
any faulty components
specified in the SEL.
Warning: Control
Panel is not
installed.
The control panel is not
installed or has a faulty
cable connection.
Install the control panel, or
check the cable connections
between the display module,
the control panel board, and
the system board. See "Control
Panel Assembly" on page 104.
Warning! No micro
code update
loaded for
processor n.
Micro code update failed. Update the BIOS firmware.
See "Getting Help" on
page 135.
Message Causes Corrective Actions
Coaster_HOM.book Page 30 Monday, November 3, 2014 3:23 PM
About Your System 31
Warning! Power
required exceeds
PSU wattage.
Check PSU and
system
configuration.
Warning!
Performance
degraded. CPU and
memory set to
minimum
frequencies to
meet PSU wattage.
System will
reboot.
The system configuration
of the processor, memory
modules, and expansion
cards may not be supported
by the power supplies.
If any system components
were just upgraded, return the
system to the previous
configuration. If the system
boots without this warning,
then the replaced
component(s) are not
supported with this power
supply. See "Power Supply" on
page 99.
Warning!
Unsupported
memory
configuration
detected. The
memory
configuration is
not optimal. The
recommended
memory
configuration
is: <message>.
Invalid memory
configuration. The system
will run but with reduced
functionality.
Ensure that the memory
modules are installed in a valid
configuration. See "General
Memory Module Installation
Guidelines" on page 86. If the
problem persists, see
"Troubleshooting System
Memory" on page 119.
Write fault.
Write fault on
selected drive.
Faulty USB device, USB
medium, optical drive
assembly, hard drive, or
hard-drive subsystem.
Replace the USB medium or
device. Ensure that the USB or
SATA cables are properly
connected. See
"Troubleshooting a USB
Device" on page 112 and
"Troubleshooting a Hard
Drive" on page 123.
NOTE: For the full name of an abbreviation or acronym used in this table, see the
Glossary
on support.dell.com.
Message Causes Corrective Actions
Coaster_HOM.book Page 31 Monday, November 3, 2014 3:23 PM
32 About Your System
Warning Messages
A warning message alerts you to a possible problem and prompts you to
respond before the system continues a task. For example, before you format a
hard drive, a message warns you that you may lose all data on the hard drive.
Warning messages usually interrupt the task and require you to respond by
typing y (yes) or n (no).
NOTE: Warning messages are generated by either the application or the operating
system. For more information, see the documentation that accompanied the
operating system or application.
Diagnostics Messages
The system diagnostic utilities may issue messages if you run diagnostic tests
on your system. See "Running the System Diagnostics" on page 127 for more
information about system diagnostics.
Alert Messages
Systems management software generates alert messages for your system. Alert
messages include information, status, warning, and failure messages for drive,
temperature, fan, and power conditions. For more information, see the
systems management software documentation.
Other Information You May Need
WARNING: See the safety and regulatory information that shipped with your
system. Warranty information may be included within this document or as a
separate document.
•The
Getting Started Guide
provides an overview of system features, setting
up your system, and technical specifications.
• Any media that ships with your system that provides documentation and
tools for configuring and managing your system, including those
pertaining to the operating system, system management software, system
updates, and system components that you purchased with your system.
NOTE: Always check for updates on support.dell.com/manuals and read the
updates first because they often supersede information in other documents.
Coaster_HOM.book Page 32 Monday, November 3, 2014 3:23 PM
About Your System 33
Coaster_HOM.book Page 33 Monday, November 3, 2014 3:23 PM
34 About Your System
Coaster_HOM.book Page 34 Monday, November 3, 2014 3:23 PM
Using the System Setup Program and UEFI Boot Manager 35
2
Using the System Setup Program
and UEFI Boot Manager
The System Setup program is the BIOS program that enables you to manage
your system hardware and specify BIOS-level options. From the System Setup
program, you can:
• Change the NVRAM settings after you add or remove hardware
• View the system hardware configuration
• Enable or disable integrated devices
• Set performance and power management thresholds
• Manage system security
Choosing the System Boot Mode
The System Setup program also enables you to specify the boot mode for
installing your operating system:
• BIOS boot mode (the default) is the standard BIOS-level boot interface.
• UEFI boot mode is an enhanced 64-bit boot interface based on Unified
Extensible Firmware Interface (UEFI) specifications that overlays the
system BIOS. See "Entering the UEFI Boot Manager" on page 47 for more
information on this interface.
You must select the boot mode in the Boot Mode field of the "Boot Settings
Screen" on page 41 of the System Setup program. Once you specify the boot
mode, the system boots in the specified boot mode and you proceed then to
install your operating system from that mode. Thereafter, you must boot the
system to the same boot mode (BIOS or UEFI) to access the installed
operating system. Trying to boot the operating system from the other boot
mode will cause the system to halt immediately at startup.
NOTE: Operating systems must be UEFI-compatible (for example, Microsoft
Windows Server 2008 x64 version) to be installed from the UEFI boot mode. DOS and
32-bit operating systems do not support UEFI and can only be installed from the
BIOS boot mode.
Coaster_HOM.book Page 35 Monday, November 3, 2014 3:23 PM
36 Using the System Setup Program and UEFI Boot Manager
Entering the System Setup Program
1
Turn on or restart your system.
2
Press <F2> immediately after you see the following message:
<F2> = System Setup
If your operating system begins to load before you press <F2>, allow the
system to finish booting, and then restart your system and try again.
Responding to Error Messages
If an error message appears while the system is booting, make a note of the
message. See "System Messages" on page 19 for an explanation of the message
and suggestions for correcting errors.
NOTE: After installing a memory upgrade, it is normal for your system to display a
message the first time you start your system.
Using the System Setup Program Navigation Keys
NOTE: For most of the options, any changes that you make are recorded but do not
take effect until you restart the system.
Keys Action
Up arrow or <Shift><Tab> Moves to the previous field.
Down arrow or <Tab> Moves to the next field.
<Enter>, Spacebar, <+>,
<–>, left and right arrows
Cycles through the settings in a field. In many
fields, you can also type the appropriate value.
<Esc> Exits the System Setup program and restarts the
system if any changes were made.
<F1> Displays the System Setup program's help file.
Coaster_HOM.book Page 36 Monday, November 3, 2014 3:23 PM
Using the System Setup Program and UEFI Boot Manager 37
System Setup Options
Main Screen
NOTE: The options for the System Setup program change based on the system
configuration.
NOTE: The System Setup program defaults are listed under their respective options
in the following sections, where applicable.
Option Description
System Time Sets the time on the system's internal clock.
System Date Sets the date on the system's internal calendar.
Memory Settings Displays information related to installed memory. See
"Memory Settings Screen" on page 39.
Processor Settings Displays information related to the processor (speed,
cache size, and so on). See "Processor Settings Screen"
on page 39.
Coaster_HOM.book Page 37 Monday, November 3, 2014 3:23 PM
38 Using the System Setup Program and UEFI Boot Manager
SATA Settings Displays a screen to enable or disable the integrated
SATA controller and ports. See "SATA Settings Screen"
on page 40.
Boot Settings Displays a screen to specify the boot mode (BIOS or
UEFI). For BIOS boot mode, you can also specify the
boot devices. See "Boot Settings Screen" on page 41.
Integrated Devices Displays a screen to enable or disable integrated device
controllers and ports, and to specify related features
and options. See "Integrated Devices Screen" on
page 41.
PCI IRQ Assignment Displays a screen to change the IRQ assigned to each of
the integrated devices on the PCI bus, and any installed
expansion card that requires an IRQ. See "PCI IRQ
Assignments Screen" on page 42.
Serial Communication Displays a screen to enable or disable the serial ports
and specify related features and options. See "Serial
Communication Screen" on page 43.
Power Management Enables you to manage power usage of the processor,
fans, and memory modules with preconfigured or
customized settings. See "Power Management Screen"
on page 44.
System Security Displays a screen to configure the system password and
setup password features. See "System Security Screen"
on page 45, "Using the System Password" on page 49,
and "Using the Setup Password" on page 52 for
more information.
Keyboard NumLock
(
On
default)
Determines whether your system starts up with the
NumLock mode activated on 101- or 102-key keyboards
(does not apply to 84-key keyboards).
Report Keyboard Errors
(
Report
default)
Enables or disables reporting of keyboard errors during
the POST. Select Report for host systems that have
keyboards attached. Select Do Not Report to suppress
all error messages relating to the keyboard or keyboard
controller during POST. This setting does not affect the
operation of the keyboard itself if a keyboard is attached
to the system.
Option Description
Coaster_HOM.book Page 38 Monday, November 3, 2014 3:23 PM
Using the System Setup Program and UEFI Boot Manager 39
Memory Settings Screen
Processor Settings Screen
F1/F2 Prompt on Error
(Enabled default)
Enables the system to halt on errors during POST,
which allows the user to observe events that may scroll
by unnoticed during normal POST. The user can press
<F1> to continue or <F2> to enter the System Setup
program.
CAUTION: When setting this option to Disabled,
the system does not halt if an error occurs during
POST. Any critical errors are displayed and logged
in the system event log.
Option Description
System Memory Size Displays the amount of system memory.
System Memory Type Displays the type of system memory.
System Memory Speed Displays the system memory speed.
Video Memory Displays the amount of video memory.
System Memory Testing
(Enabled default)
Specifies whether system memory tests are run at system
boot. Options are Enabled and Disabled.
Option Description
64-bit Specifies if the processor supports 64-bit extensions.
Core Speed Displays the processor clock speed.
Bus Speed Displays the processor bus speed.
Processor Family-Model-
Stepping
Displays the processor family and model.
Level 2 Cache Displays the level 2 cache size.
Level 3 Cache Displays the level 3 cache size.
Number of Cores Displays the number of cores of the processor.
Option Description
Coaster_HOM.book Page 39 Monday, November 3, 2014 3:23 PM
40 Using the System Setup Program and UEFI Boot Manager
SATA Settings Screen
Logical Processor
(Enabled default)
On processors that support Simultaneous Multi-
Threading (SMT) technology, each processor core
supports up to two logical processors. If this field is set to
Enabled, the BIOS reports both logical processors. If set
to Disabled, only one logical processor is monitored by
the BIOS.
Virtualization Technology
(Disabled default)
Enabled permits virtualization software to use the
virtualization technology incorporated in the processor.
NOTE: Disable this feature if your system will not be
running virtualization software.
Execute Disable
(Enabled default)
Enables or disables Execute Disable Memory Protection
Technology.
Number of Cores per
Processor
(All default)
If set to All, the maximum number of cores in each
processor is enabled.
Tu rbo Mode
(Enabled default)
If Turbo Boost technology is supported by the processor,
enables or disables Tu rb o Mode .
C States
(Enabled default)
When set to Enabled, the processor can operate in all
available power states.
Option Description
Embedded SATA
(AHCI default)
Allows the embedded SATA to be set to Off, ATA, AHCI,
or RAID modes.
NOTE: The UEFI support is disabled if SATA is set to the
RAID mode.
Port A
(Auto default)
Auto enables BIOS support for the device attached to
SATA port A. Off disables BIOS support for the device.
Port B
(Off default)
Auto enables BIOS support for the device attached to
SATA port B. Off disables BIOS support for the device.
Port C
(Off default)
Auto enables BIOS support for the device attached to
SATA port C. Off disables BIOS support for the device.
Option Description
Coaster_HOM.book Page 40 Monday, November 3, 2014 3:23 PM
Using the System Setup Program and UEFI Boot Manager 41
Boot Settings Screen
Integrated Devices Screen
Port D
(Off default)
Auto enables BIOS support for the device attached to
SATA port C. Off disables BIOS support for the device.
Port E
(Auto default)
Auto enables BIOS support for the device attached to
SATA port C. Off disables BIOS support for the device.
eSATA port
(Auto default)
Auto enables BIOS support for the device attached to the
eSATA port. Off disables BIOS support for the device.
Option Description
Boot Mode
(BIOS default)
CAUTION: Switching the boot mode could prevent
the system from booting if the operating system was
not installed in the same boot mode.
If the operating system supports Unified Extensible
Firmware Interface, you can set this option to UEFI.
Setting this field to BIOS allows compatibility with non-
UEFI operating systems.
NOTE: Setting this field to UEFI disables the Boot
Sequence, Hard-Disk Drive Sequence, and USB Flash Drive
Emulation Type fields.
Boot Sequence Retry
(Disabled default)
If this field is enabled and the system has failed to boot,
the system will reattempt to boot after 30 seconds.
Option Description
User Accessible
USB Ports
(All Ports On default)
Enables or disables the user-accessible USB ports.
Options are All Ports On, Only Back Ports On, and All
Ports Off.
Internal USB Port
(On default)
Enables or disables the internal USB port.
Embedded NIC1 and
NIC2
(Enabled default)
Enables or disables the operating system interface of the
NIC1 and NIC2 controllers. (The NICs may also be
accessed through the system’s management controller).
Option Description
Coaster_HOM.book Page 41 Monday, November 3, 2014 3:23 PM
42 Using the System Setup Program and UEFI Boot Manager
PCI IRQ Assignments Screen
Embedded Gb NIC 1
(Enabled with PXE
default)
Enables or disables the embedded NICs. PXE support
allows the system to boot from the network. Enabled
with iSCSI Boot option is available if the NIC on board
supports iSCSI.
MAC Address Displays the MAC address for the NIC.
Embedded Gb NIC2
(Enabled with PXE
default)
Enables or disables the embedded NICs. PXE support
allows the system to boot from the network. Enabled
with iSCSI Boot option is available if the NIC on board
supports iSCSI.
MAC Address Displays the MAC address for the NIC.
OS Watchdog Timer
(Disabled default)
Sets a timer to monitor the operating system for activity,
and aids in recovery if the system stops responding.
When Enabled, the operating system is allowed to
initialize the timer. When Disabled, the timer is
not initialized.
NOTE: This feature is usable only with operating systems
that support WDAT implementations of the Advanced
Configuration and Power Interface (ACPI) 3.0b
specification.
Embedded Video
Controller
(Standard default)
Enables or disables BIOS support for the integrated
video controller.
NOTE: This field can be disabled only if an add-in video
card is present. If this field is disabled, remote access
features such as virtual KVM are not available.
Option Description
<PCIe device> Use the <+> and <-> keys to manually select an IRQ
for a given device, or select Default to allow the BIOS to
select an IRQ value at system startup.
Option Description
Coaster_HOM.book Page 42 Monday, November 3, 2014 3:23 PM
Using the System Setup Program and UEFI Boot Manager 43
Serial Communication Screen
Option Description
Serial Communication
(On without Console
Redirection default)
Selects whether the serial communication devices
(Serial Device 1 and Serial Device 2) are enabled in
BIOS. BIOS console redirection can also be enabled and
the port address used can be specified.
Options are On without Console Redirection, On with
Console Redirection via COM1, On with Console
Redirection via COM2, and Off.
Serial Port Address
(Serial Device 1=COM1,
Serial Device2=COM2
default)
Sets the serial port addresses for the two serial devices.
NOTE: Only Serial Device 2 can be used for SOL. To use
console redirection by SOL, configure the same port
address for console redirection and the serial device.
External Serial
Connector
(Serial Device1 default)
Specifies whether Serial Device 1, Serial Device 2, or
Remote Access Device has access to the external serial
connector.
NOTE: Only Serial Device 2 can be used for Serial Over
LAN (SOL). To use console redirection by SOL, configure
the same port address for console redirection and the
serial device.
Failsafe Baud Rate
(115200 default)
Displays the failsafe baud rate used for console
redirection. BIOS attempts to determine the baud rate
automatically. This failsafe baud rate is used only if the
attempt fails. This rate should not be adjusted.
Remote Terminal Type
(VT 100/VT220 default)
Sets the remote console terminal type, either
VT100/VT220 or ANSI.
Redirection After Boot
(Enabled default)
Enables or disables BIOS console redirection when the
operating system is loaded.
Coaster_HOM.book Page 43 Monday, November 3, 2014 3:23 PM
44 Using the System Setup Program and UEFI Boot Manager
Power Management Screen
Option Description
Power Management
(OS Control default)
Options are OS Control, Active Power Controller,
Custom, or Maximum Performance. For all but the
Custom setting, the BIOS pre-configures the power
settings on this screen as follows:
•
OS Control
sets the CPU power to
OS DBPM
, the fan
power to
Minimum Power
, and the memory power to
Maximum Performance
. In this setting, all processor
performance information is passed from the system
BIOS to the operating system for control. The operating
system sets the processor performance based on
processor utilization.
•
Active Power Controller
sets the CPU power to
System
DBPM
, the fan power to
Minimum Power
, and the
memory power to
Maximum Performance
. The BIOS
sets the processor performance based on
processor utilization.
•
Maximum Performance
sets all fields to
Maximum
Performance
.
If you select Custom, you can configure each
option independently.
CPU Power and
Performance
Management
Options are OS DBPM, System DBPM, Maximum
Performance, or Minimum Power.
Fan Power and
Performance
Management
Options are Maximum Performance or Minimum Power.
Memory Power and
Performance
Management
Options are Maximum Performance, a specified
frequency, or Minimum Power.
Coaster_HOM.book Page 44 Monday, November 3, 2014 3:23 PM
Using the System Setup Program and UEFI Boot Manager 45
System Security Screen
Option Description
TPM Security
(Off default)
Sets the reporting of the Trusted Platform Module
(TPM) in the system.
If Off, the presence of the TPM is not reported to the
operating system.
If On with Pre-boot Measurements, the system reports
the TPM to the operating system and stores the pre-boot
measurements to the TPM during POST.
If On without Pre-boot Measurements, the system
reports the TPM to the operating system and bypasses
pre-boot measurements.
TPM Activation When set to Activate, the TPM is enabled to default
settings. When set to Deactivate, the TPM is disabled.
The No Change state initiates no action. The operational
state of the TPM remains unchanged (all user settings for
the TPM are preserved).
NOTE: This field is read-only when TPM Security is set to
Off.
TPM Clear CAUTION: Clearing the TPM will lose all encryption
keys in the TPM. This option prevents booting to the
operating system and results in data loss if the
encryption keys cannot be restored. Back up the TPM
keys prior to enabling this option.
When set to Yes, all TPM contents are cleared.
NOTE: This field is read-only when TPM Security is set
to Off.
Intel (R) TXT
(Disabled default)
Enables/disables Trusted Execution Technology. To
enable TXT, enable & activate VT & TPM with preboot
measurement.
System Password
(Not Enabled default)
Displays the current status of the password security
feature and allows a new system password assignment and
verification.
NOTE: See "Using the System Password" on page 49 for
more information.
Coaster_HOM.book Page 45 Monday, November 3, 2014 3:23 PM
46 Using the System Setup Program and UEFI Boot Manager
Setup Password
(Not Enabled default)
Restricts access to the System Setup program by using a
setup password.
NOTE: See "Using the Setup Password" on page 52 for more
information.
Password Status
(Unlocked default)
When Setup Password is assigned and this field is
Locked, the system password cannot be changed or
disabled at system start-up.
See "Using the System Password" on page 49 for more
information.
Set Setup Password Allows a new setup password assignment.
Set System Password Allows a new system password assignment.
Power Button
(Enabled default)
If Enabled, the power button can turn the system's power
off and on. On an
ACPI-compliant operating system, the
system performs an orderly shutdown before power is
turned off.
When Disabled, the button can only turn on system
power.
NMI Button
(Disabled default)
CAUTION: Use the NMI button only if directed to do
so by qualified support personnel or by the operating
system's documentation. Pressing this button halts
the operating system and displays a diagnostic
screen.
Enables or disables the NMI feature.
AC Power Recovery
(Last default)
Determines how the system reacts when power is
restored. If set to Last, the system returns to the last
power state. On turns on the system after power is
restored. Off allows the system to remain off after power
is restored.
AC Power Recovery
Delay (Immediate
default)
Determines when the system restarts after power is
restored. Options are Immediate, Random (a random
value of 45 to 240 seconds), or a user-defined value of 45
to 240 seconds.
Option Description
Coaster_HOM.book Page 46 Monday, November 3, 2014 3:23 PM
Using the System Setup Program and UEFI Boot Manager 47
Exit Screen
Press <Esc> to exit the System Setup program; the Exit screen displays:
•Save Changes and Exit
•Discard Changes and Exit
•Return to Setup
Entering the UEFI Boot Manager
NOTE: Operating systems must be 64-bit UEFI-compatible (for example, Microsoft
Windows Server 2008 x64 version) to be installed from the UEFI boot mode. DOS and
32-bit operating systems can only be installed from the BIOS boot mode.
NOTE: The Boot Mode must be set to UEFI in the System Setup program to access
the UEFI Boot Manager.
The UEFI Boot Manager enables you to:
• Add, delete, and arrange boot options
• Access the System Setup program and BIOS-level boot options without
rebooting
To enter the UEFI Boot Manager:
1
Turn on or restart your system.
2
Press <F11> after you see the following message:
<F11> = UEFI Boot Manager
NOTE: The system will not respond until the USB keyboard is active.
If your operating system begins to load before you press <F11>, allow the
system to finish booting, and then restart your system and try again.
Using the UEFI Boot Manager Navigation Keys
Keys Action
Up arrow Moves to and highlights the previous field.
Down arrow Moves to and highlights the next field.
Spacebar, <Enter>, <+>,
<–>
Cycles through the settings in a field.
Coaster_HOM.book Page 47 Monday, November 3, 2014 3:23 PM
48 Using the System Setup Program and UEFI Boot Manager
UEFI Boot Manager Screen
UEFI Boot Settings Screen
<Esc> Refreshes the UEFI Boot Manager screen, or
returns to the UEFI Boot Manager screen from the
other program screens.
<F1> Displays the UEFI Boot Manager help file.
Option Description
Continue Normal Boot The system attempts to boot to devices starting with
the first item in the boot order. If the boot attempt fails,
the system will continue with the next item in the boot
order until the boot is successful or no more boot
options are found.
Select Boot Mode Displays the list of available boot options (marked with
asterisks). Select the boot option you wish to use and
press Enter.
NOTE: If you hot-add a boot device, press <ESC> to
refresh the list of boot options.
Boot Settings Enables you to add, delete, enable, or disable boot
options; change boot order; or execute a one-time
boot option.
System Utilities Enables you to access the System Setup program,
System Services (Dell USC), Diagnostics, and BIOS-
level boot options.
Option Description
Add Boot Option Adds a new boot option.
Delete Boot Option Deletes an existing boot option.
Enable/Disable Boot Option Disables and enables a boot option in the boot option list.
Boot From File Sets a one-time boot option not included in the boot
option list.
Set Boot Order Sets the order of the boot option list.
Keys Action
Coaster_HOM.book Page 48 Monday, November 3, 2014 3:23 PM
Using the System Setup Program and UEFI Boot Manager 49
System Utilities Screen
System and Setup Password Features
NOTE: For a forgotten password, see "Disabling a Forgotten Password" on
page 134.
Your system is shipped without the system password feature enabled. Operate
the system only with system password protection.
CAUTION: The password features provide a basic level of security for the data on
your system.
CAUTION: Anyone can access the data stored on your system if the system is
running and unattended.
Using the System Password
When a system password is assigned, the system prompts for the system
password after the system starts and only those with the password have full
use of the system.
Assigning a System Password
Before assigning a system password, enter the System Setup program and
check the System Password option.
When a system password is assigned, System Password is Enabled. If
Password Status is Unlocked, you can change the system password. If Locked,
you cannot change the system password. Disabling the password jumper on
the system board sets System Password to Disabled, and you cannot change
or enter a new system password.
Option Description
System Setup Accesses the System Setup program without rebooting.
System Services Restarts the system and accesses the Dell USC, which
allows you to run utilities such as system diagnostics.
Reset System Restarts the system.
Coaster_HOM.book Page 49 Monday, November 3, 2014 3:23 PM
50 Using the System Setup Program and UEFI Boot Manager
When a system password is not assigned and the password jumper on the
system board is in the enabled position, System Password is Not Enabled and
Password Status is Unlocked.
To assign a system password:
1
Verify that
Password Status
is
Unlocked
.
2
Highlight the
System Password
option and press <Enter>.
3
Type your new system password.
You can use up to 32 characters in your password.
As you type, placeholders appear in the field.
The password assignment is not case-sensitive. Certain key combinations
are invalid and if you enter one, the system beeps. To erase a character,
press <Backspace> or the left-arrow key.
NOTE: To escape from the field without assigning a system password, press
<Enter> to move to another field, or press <Esc> prior to completing step 5.
4
Press <Enter>.
5
To confirm your password, type it a second time and press <Enter>.
System Password
changes to
Enabled
. Exit the System Setup program and
begin using your system.
6
Either reboot the system now for the password protection to take effect or
continue working.
NOTE: Password protection does not take effect until the system reboots.
Coaster_HOM.book Page 50 Monday, November 3, 2014 3:23 PM
Using the System Setup Program and UEFI Boot Manager 51
Using Your System Password to Secure Your System
NOTE: If you have assigned a setup password (see "Using the Setup Password" on
page 52), the system accepts your setup password as an alternate system
password.
When Password Status is Unlocked, you have the option to leave the
password security enabled or to disable password security.
To leave the password security enabled:
1
Turn on or reboot your system by pressing <Ctrl><Alt><Delete>.
2
Type your password and press <Enter>.
To disable the password security:
1
Turn on or reboot your system by pressing <Ctrl><Alt><Delete>.
2
Type your password and press <Ctrl><Enter>.
When Password Status is Locked, you must type the password and press
<Enter> when prompted at reboot.
If an incorrect system password is entered, the system displays a message and
prompts you to re-enter your password. You have three attempts to enter the
correct password. After the third unsuccessful attempt, the system displays an
error message that the system has halted and will shut down.
Even after you shut down and restart the system, the error message continues
to be displayed until the correct password is entered.
NOTE: You can use the Password Status option in conjunction with the System
Password and Setup Password options to protect your system from unauthorized
changes.
Deleting or Changing an Existing System Password
1
Enter the System Setup program and select the
System Security
.
2
Highlight
Setup Password
, press <Enter> to access the setup password
window. Press <Enter> twice to clear the existing setup password.
3
The setting changes to
Not Enabled
.
4
If you want to assign a new setup password, perform the steps in "Assigning
a Setup Password" on page 52.
Coaster_HOM.book Page 51 Monday, November 3, 2014 3:23 PM
52 Using the System Setup Program and UEFI Boot Manager
Using the Setup Password
Assigning a Setup Password
You can assign a setup password only when the Setup Password is Not
Enabled. To assign a setup password, highlight the Setup Password option
and press the <+> or <–> key. The system prompts you to enter and verify
the password.
NOTE: The setup password can be the same as the system password. If the two
passwords are different, the setup password can be used as an alternate system
password. The system password cannot be used in place of the setup password.
You can use up to 32 characters in your password.
As you type, placeholders appear in the field.
The password assignment is not case-sensitive. Certain key combinations are
invalid and if you enter one, the system beeps. To erase a character, press
<Backspace> or the left-arrow key.
When you verify the password, the Setup Password changes to Enabled. The
next time you enter the System Setup program, the system prompts you for
the setup password.
A change to the Setup Password option becomes effective immediately
(restarting the system is not required).
Operating With a Setup Password Enabled
If Setup Password is Enabled, you must enter the correct setup password
before modifying most of the System Setup options.
If you do not enter the correct password in three attempts, the system lets you
view, but not modify, the System Setup screens. The following options are
exceptions: If System Password is not Enabled and is not locked through the
Password Status option, you can assign a system password. You cannot disable
or change an existing system password.
NOTE: You can use the Password Status option in conjunction with the Setup
Password option to protect the system password from unauthorized changes.
Coaster_HOM.book Page 52 Monday, November 3, 2014 3:23 PM
Using the System Setup Program and UEFI Boot Manager 53
Deleting or Changing an Existing Setup Password
1
Enter the System Setup program and select the
System Security
.
2
Highlight
Setup Password
, press <Enter> to access the setup password
window. Press <Enter> twice to clear the existing setup password.
The setting changes to
Not Enabled
.
3
If you want to assign a new setup password, perform the steps in "Assigning
a Setup Password" on page 52.
Embedded System Management
Dell USC is an embedded utility that enables systems and storage
management tasks from an embedded environment throughout the server’s
lifecycle.
Dell USC can be started during the boot sequence and can function
independently of the operating system.
NOTE: Certain platform configurations may not support the full set of features
provided by Dell USC.
The following features of Dell USC are supported on systems with Baseboard
Management Controller (BMC):
• Installing an operating system
• Running diagnostics to validate the memory, I/O devices, processor,
physical disks, and other peripherals
When an optional iDRAC6 Express card is installed, Dell USC provides the
following additional features:
• Downloading and applying firmware updates
• Configuring hardware and firmware
For more information about setting up Dell USC, configuring hardware and
firmware, and deploying the operating system, see the Unified Server
Configurator documentation at support.dell.com/manuals.
Baseboard Management Controller Configuration
The BMC enables configuring, monitoring, and recovery of systems remotely.
The BMC provides the following features:
Coaster_HOM.book Page 53 Monday, November 3, 2014 3:23 PM
54 Using the System Setup Program and UEFI Boot Manager
• Enables fault logging and SNMP alerting
• Provides access to system event log and sensor status
• Allows control of system functions including power on and off
• Functions independently of the system’s power state or the system’s
operating system
• Provides text console redirection for system setup, text-based utilities, and
operating system consoles
NOTE: To remotely access the BMC through the integrated NIC, you must connect
the network connection to integrated NIC1.
For additional information on using BMC, see the documentation for the
BMC and systems management applications.
Entering the BMC Setup Module
1
Turn on or restart your system.
2
Press <Ctrl><E> when prompted after POST.
If your operating system begins to load before you press <Ctrl><E>,
allow the system to finish booting, and then restart your system and try
again.
iDRAC Configuration Utility
The iDRAC Configuration Utility is a pre-boot configuration environment
that allows you to view and set parameters for the iDRAC6 and for the
managed server.
The iDRAC Configuration Utility provides the following features:
• Enables fault logging and SNMP alerting
• Provides access to system event log and sensor status
• Allows control of system functions including power on and off
• Functions independently of the system’s power state or the system’s
operating system
• Provides text console redirection for system setup, text-based utilities, and
operating system consoles.
Coaster_HOM.book Page 54 Monday, November 3, 2014 3:23 PM
Using the System Setup Program and UEFI Boot Manager 55
In addition, the iDRAC Configuration Utility enables you to:
• Configure, enable, or disable the iDRAC6 local area network through the
dedicated iDRAC6 Enterprise card port or the embedded NIC1.
• Enable or disable IPMI over LAN
• Enable a LAN Platform Event Trap (PET) destination
• Attach or detach the Virtual Media devices
• Change the administrative user name and password and manage user
privileges
• View System Event Log (SEL) messages or clear messages from the log
For additional information on using iDRAC6, see the documentation for
iDRAC6 and systems management applications.
Entering the iDRAC Configuration Utility
1
Turn on or restart your system.
2
Press <Ctrl><E> when prompted during POST.
If your operating system begins to load before you press <Ctrl><E>,
allow the system to finish booting, and then restart your system and try
again.
Coaster_HOM.book Page 55 Monday, November 3, 2014 3:23 PM
56 Using the System Setup Program and UEFI Boot Manager
Coaster_HOM.book Page 56 Monday, November 3, 2014 3:23 PM
Installing System Components 57
3
Installing System Components
Recommended Tools
You may need the following items to perform the procedures in this section:
• Key to the system keylock
•#2 Phillips screwdriver
•W
rist grounding stra
p
Coaster_HOM.book Page 57 Monday, November 3, 2014 3:23 PM
58 Installing System Components
Inside the System
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
Figure 3-1. Inside the System
1 power supply 2 chassis intrusion switch
3 cooling shroud 4 expansion card stabilizer
5 heat sink 6 hard drives (6)
7 tape drive (optional) 8 optical drive (optional)
3
5
1
8
4
6
7
2
Coaster_HOM.book Page 58 Monday, November 3, 2014 3:23 PM
Installing System Components 59
Opening and Closing the System
WARNING: Whenever you need to lift the system, get others to assist you. To
avoid injury, do not attempt to lift the system by yourself.
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
Opening the System
1
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
2
Press the power button to ground the system board.
3
Lay the system on its side as shown in Figure 3-2.
4
Open the system by sliding the cover release tab toward the back of the
system, grasp the cover on both sides, and carefully lift the cover away
from the system. See Figure 3-2.
Coaster_HOM.book Page 59 Monday, November 3, 2014 3:23 PM
60 Installing System Components
Figure 3-2. Opening and Closing the System
Closing the System
1
Align the cover with the slots on the bottom of the chassis. See Figure 3-2.
2
Press down on the cover until the cover release tab snaps into place.
3
Place the system upright on a flat, stable surface.
4
Reattach any peripherals and connect the system to an electrical outlet.
5
Turn on the system and attached peripherals.
1 release tab
1
Coaster_HOM.book Page 60 Monday, November 3, 2014 3:23 PM
Installing System Components 61
Front Bezel
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
Removing the Front Bezel
1
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
2
Open the system. See "Opening the System" on page 59.
3
Slide the drive release latch in the direction of the arrow until it releases
the front bezel from its side hinges. See Figure 3-3.
NOTE: The drive release latch secures and releases the front bezel and helps
to secure the drives.
4
Carefully tilt the front bezel away from the chassis and lift it out as shown
in Figure 3-3.
5
Close the system. See "Closing the System" on page 60.
Coaster_HOM.book Page 61 Monday, November 3, 2014 3:23 PM
62 Installing System Components
Figure 3-3. Removing and Installing the Front Bezel
Installing the Front Bezel
1
Align the tabs on the front bezel with the slots on the chassis.
See Figure 3-3.
2
Snap the bezel into place.
Removing Front Bezel Insert
NOTE: Before installing a drive in one or more of the front drive bays, remove the
corresponding insert(s) on the front bezel.
1
From the back of the bezel, push the tab on the end of the insert outward.
2
Pull the insert away from the bezel. See Figure 3-4.
1 drive release latch 2 front bezel
1
2
Coaster_HOM.book Page 62 Monday, November 3, 2014 3:23 PM
Installing System Components 63
Figure 3-4. Removing and Installing the Front Bezel Insert
Installing Front Bezel Insert
1
To replace the insert on the front bezel, from the back of the bezel, fit the
tabs on the end of the insert into the notches on the bezel.
2
Snap the other end of the insert into place. See Figure 3-4.
EMI Filler Panel
Depending on the configuration of your system, an electromagnetic
interference (EMI) filler panel may be installed in one or more of the 5.25-
inch optical drive bays at the front of the system. EMI filler panels are
essential for airflow efficiency and for electromagnetic interference
protection. Before installing an optical drive, the corresponding EMI filler
panel must first be removed.
Removing an EMI Filler Panel
1
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
2
Open the system. See "Opening the System" on page 59.
1 front bezel 2 front bezel insert
3 insert tab
1
2
3
Coaster_HOM.book Page 63 Monday, November 3, 2014 3:23 PM
64 Installing System Components
3
Remove the front bezel. See "Removing the Front Bezel" on page 61.
4
Slide the drive release latch in the direction of the arrow to release the
shoulder screw. See Figure 3-5.
5
Pull the tab to remove the EMI filler panel.
Figure 3-5. Removing and Installing the EMI Filler Panel
Installing an EMI Filler Panel
1
Gently slide the EMI filler panel into the bay until it clicks into place. See
Figure 3-5.
2
Replace the front bezel. See "Installing the Front Bezel" on page 62.
3
Close the system. See "Closing the System" on page 60.
1 drive release latch 2 shoulder screws (2)
3 EMI filler panel 4 tab
3
2
4
1
Coaster_HOM.book Page 64 Monday, November 3, 2014 3:23 PM
Installing System Components 65
Optical and Tape Drives (Optional)
Your system contains two 5.25-inch drive bays. In the upper 5.25-inch drive
bay, you can install only an optical drive. In the lower 5.25-inch drive bay, you
can install either an optical or a tape backup unit.
Removing an Optical or Tape Drive
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
2
Open the system. See "Opening the System" on page 59.
3
Remove the front bezel. See "Removing the Front Bezel" on page 61.
4
Disconnect the power and data cables from the back of the drive. See
Figure 3-6 for disconnecting SCSI connections and Figure 3-7 for
disconnecting SATA connections.
5
Slide the drive release latch in the direction of the arrow to release the
shoulder screw.
6
Slide the drive out to remove it from the drive bay.
Coaster_HOM.book Page 65 Monday, November 3, 2014 3:23 PM
66 Installing System Components
Figure 3-6. Removing and Installing a Tape Drive (SCSI Connection)
1 power cable 2 data cable
3 drive release latch 4 drive bay screw slots
5 tape drive 6 tape drive shoulder screws (3)
6
5
3
4
1
2
Coaster_HOM.book Page 66 Monday, November 3, 2014 3:23 PM
Installing System Components 67
Figure 3-7. Removing and Installing an Optical Drive (SATA Connection)
7
If you are installing another drive in the bay, see "Installing an Optical or
Tape Drive" on page 6 8.
8
If the drive is being permanently removed, install an insert on the front
bezel. See "Installing Front Bezel Insert" on page 63.
9
Replace the front bezel. See "Installing the Front Bezel" on page 62.
10
Close the system. See "Closing the System" on page 60.
1 power/data cable 2 drive release latch
3 drive bay screw slots 4 optical drive
5 optical drive shoulder screws (3)
5
4
2
3
1
Coaster_HOM.book Page 67 Monday, November 3, 2014 3:23 PM
68 Installing System Components
Installing an Optical or Tape Drive
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Unpack the drive and prepare it for installation. For instructions, see the
documentation that accompanied the drive.
If you are installing a SCSI tape drive, you must have a SCSI
controller
card installed (see "Installing an Expansion Card" on page 84) and
configure the tape drive according to the documentation that came with
the tape drive.
NOTE: Each device attached to a SCSI host adapter must have a unique SCSI
ID number (narrow SCSI devices use IDs 0 to 7; wide SCSI devices use IDs
from 0 to 15). Set the drive’s SCSI ID to avoid conflicts with other devices on
the SCSI bus. For the default SCSI ID setting, see the documentation provided
with the drive.
NOTE: There is no requirement that SCSI ID numbers be assigned
sequentially or that devices be attached to the cable in order by ID number.
NOTE: SCSI logic requires that the two devices at opposite ends of a SCSI
chain be terminated and that all devices in between be unterminated.
Therefore, you enable the tape drive’s termination if it is the last device in a
chain of devices (or sole device) connected to the SCSI controller.
2
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
3
Open the system. See "Opening the System" on page 59.
4
Remove the front bezel. See "Removing the Front Bezel" on page 61.
5
If another drive is installed, remove it (see "Removing an Optical or Tape
Drive" on page 65) and remove the three shoulder screws to attach to the
new drive. See Figure 3-8.
6
If the drive bay is empty, remove the insert on the front bezel. See
"Removing Front Bezel Insert" on page 62.
7
Remove the two shoulder screws from the EMI filler panel and attach
them to the new drive. See Figure 3-8.
Coaster_HOM.book Page 68 Monday, November 3, 2014 3:23 PM
Installing System Components 69
8
On the new drive, attach the three shoulder screws to the drive, one screw
on the lower front screw hole on the right side and two screws on the lower
screw holes on the left side. See Figure 3-8.
Figure 3-8. Installing Drive Shoulder Screws
*Screws are supplied along with the drives ordered from Dell.
9
Gently slide the drive into the bay until it clicks into place.
10
Attach the SCSI power cable (tape drive) or SATA power cable (optical
drive) to the drive. Ensure that cables are secured in their respective clips.
11
Attach the data cable. If you are installing a SCSI tape drive, connect the
SCSI interface cable in the drive kit from the SCSI controller card to the
drive.
12
Check all cable connections, and fold cables out of the way to allow for
airflow between the fan and cooling vents.
13
Replace the front bezel. See "Installing the Front Bezel" on page 62.
14
Close the system. See "Closing the System" on page 60.
1 shoulder screws (3)*
1
Coaster_HOM.book Page 69 Monday, November 3, 2014 3:23 PM
70 Installing System Components
Hard Drives
NOTE: The system’s drive configuration must consist of either all SATA hard drives
or all SAS hard drives; mixed configurations are not supported.
Hard Drive Installation Guidelines
Your system supports up to four 3.5-inch or six 2.5-inch hard drives in internal
drive bays.
Removing a 3.5-Inch Hard Drive
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet and from the peripherals.
2
Open the system. See "Opening the System" on page 59.
3
Disconnect the data/power cable from the hard drive by pulling up on the
blue tab.
4
Press the blue tabs on each side of the hard-drive bracket toward each
other and slide the drive up and out of the bay. See Figure 3-9.
Coaster_HOM.book Page 70 Monday, November 3, 2014 3:23 PM
Installing System Components 71
Figure 3-9. Removing or Installing a 3.5-Inch Hard Drive
NOTE: If you are not replacing the hard drive, remove the drive from the drive
bracket (see Figure 3-11) and insert the empty bracket back into the drive bay.
5
Detach the hard-drive bracket from the hard drive by pushing out at the
edges of the bracket and removing the hard drive. See
Figure 3-11
.
6
Close the system. See "Closing the System" on page 60.
7
Place the system upright on a flat, stable surface.
8
Reconnect the system to its electrical outlet and turn the system on,
including any attached peripherals.
1 hard drive 2 power/data cable
3 tabs (2) 4 hard drive bracket
2
4
3
1
Coaster_HOM.book Page 71 Monday, November 3, 2014 3:23 PM
72 Installing System Components
Installing a 3.5-Inch Hard Drive
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
2
Open the system. See "Opening the System" on page 59.
3
To remove the existing hard-drive bracket, press the blue tabs on each side
of the bracket toward each other and slide the bracket up and out of the
system. See Figure 3-9.
4
Snap the hard-drive bracket on to the hard drive. See Figure 3-11.
5
Slide the hard drive into the drive bay until it snaps into place.
6
Connect the power/data cable to the hard drive.
• For connection to the integrated SATA controller (SATA hard drives
only), connect the SATA data cable to the SATA connectors on the
system board. See Figure 6-1 for the location of the hard drive
connectors on the system board.
• For connection to a SAS controller expansion card (SAS or SATA hard
drives), connect the data/power cable from the SAS controller card as
shown in Figure 3-10. See "SAS Controller Expansion Card" on
page 85 for instructions about installing the card and routing the
cables.
NOTE: The SAS controller card must be installed in SLOT1 PCIE_G2_X8. See
Figure 6-1.
Coaster_HOM.book Page 72 Monday, November 3, 2014 3:23 PM
Installing System Components 73
Figure 3-10. Attaching a SAS Hard Drive to a SAS Controller Expansion Card
7
Close the system. See "Closing the System" on page 60.
8
Place the system upright on a flat, stable surface.
9
Reconnect the system to its electrical outlet and turn the system on,
including any attached peripherals.
10
Enter the System Setup program and ensure that the hard drive’s
controller is enabled. See "Entering the System Setup Program" on
page 36.
11
Exit the System Setup program and reboot the system.
12
Partition and logically format the drive.
See the documentation that came with the drive for instructions on
installing any software required for drive operation.
1 SAS hard drive 2 power/data cable to hard drive
3 data cable to SAS controller card 4 SAS controller card
3
4
1
2
Coaster_HOM.book Page 73 Monday, November 3, 2014 3:23 PM
74 Installing System Components
Removing a 3.5-Inch Hard Drive From a Hard-Drive Bracket
Detach the hard-drive bracket from the hard drive by pushing out at the
edges of the bracket and removing the hard drive. See Figure 3-11.
Figure 3-11. Removing or Installing a Hard Drive From a Hard-Drive Bracket
Removing a 2.5-Inch Hard Drive
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet and from the peripherals.
1 hard drive 2 hard drive bracket
3 blue tabs (2)
3
1
2
Coaster_HOM.book Page 74 Monday, November 3, 2014 3:23 PM
Installing System Components 75
2
Open the system. See "Opening the System" on page 59.
3
Disconnect the data/power cable from the hard drive by pulling up on the
blue tab.
4
Press the blue tabs on each side of the hard-drive bracket toward each
other and slide the bracket up and out of the bay. See Figure 3-12.
Figure 3-12. Removing a 2.5-Inch Hard Drive Carrier
5
Remove the four screws on the two sides of the hard-drive carrier and pull
out the hard drive. See Figure 3-13.
1 hard drive 2 hard-drive bracket
3 blue tabs (4)
1
3
2
Coaster_HOM.book Page 75 Monday, November 3, 2014 3:23 PM
76 Installing System Components
Figure 3-13. Removing and Installing a 2.5-Inch Hard Drive
6Slide the hard-drive carrier back in the hard drive bay.
7Close the system. See "Closing the System" on page 60.
8
Place the system upright on a flat, stable surface.
9
Reconnect the system to its electrical outlet and turn the system on,
including any attached peripherals.
Installing a 2.5-Inch Hard Drive
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
1 hard drive 2 screws (4)
3 hard-drive bracket
1
2
3
Coaster_HOM.book Page 76 Monday, November 3, 2014 3:23 PM
Installing System Components 77
2
Open the system. See "Opening the System" on page 59.
3
To remove the existing hard-drive bracket, see step 4 of "Removing a 2.5-
Inch Hard Drive" on page 74.
4Slide the hard-drive carrier back in the hard drive bay
.
5
Slide the hard drive into the drive bay until it snaps into place.
6
Secure the hard drive to the hard-drive bracket using the four screws. See
Figure 3-13.
7
Connect the power/data cable to the hard drive. See Figure 3-14
Figure 3-14. Attaching Power/Data Cable to the Hard Drive
8
Close the system. See "Closing the System" on page 60.
9
Place the system upright on a flat, stable surface.
1 power/data cables 2 hard drives
1
2
Coaster_HOM.book Page 77 Monday, November 3, 2014 3:23 PM
78 Installing System Components
10
Reconnect the system to its electrical outlet and turn the system on,
including any attached peripherals.
11
Enter the System Setup program and ensure that the hard drive’s
controller is enabled. See "Entering the System Setup Program" on
page 36.
12
Exit the System Setup program and reboot the system.
13
Partition and logically format the drive.
See the documentation that came with the drive for instructions on installing
any software required for drive operation.
Expansion-Card Stabilizer
Removing the Expansion-Card Stabilizer
1
Turn off the system and attached peripherals. Disconnect the system from
the electrical outlet and peripherals.
2
Open the system. See "Opening the System" on page 59.
3
Press the release tab and lift the expansion card stabilizer out of slots in the
chassis. See Figure 3-15.
Installing the Expansion-Card Stabilizer
1
Slide the edge of the expansion-card stabilizer into the slots in the cooling
shroud and chassis until the release tab locks into place. See Figure 3-15.
2
Close the system. See "Closing the System" on page 60.
Cooling Shroud
The cooling shroud directs airflow over the system processor and memory
modules.
WARNING: The memory modules and heat sink can get very hot during normal
operation. Ensure that the memory modules and heat sink have had sufficient time
to cool before you touch them.
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
Coaster_HOM.book Page 78 Monday, November 3, 2014 3:23 PM
Installing System Components 79
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
CAUTION: Never operate your system with the cooling shroud removed.
Overheating of the system can develop quickly, resulting in shutdown of the
system and loss of data.
Removing the Cooling Shroud
1
Turn off the system and attached peripherals. Disconnect the system from
the electrical outlet and peripherals.
2
Open the system. See "Opening the System" on page 59.
3
Remove the expansion-card stabilizer. See "Removing the Expansion-Card
Stabilizer" on page 78.
4
Hold the touch points on the cooling shroud and lift the cooling shroud
out of the system. See Figure 3-15.
Coaster_HOM.book Page 79 Monday, November 3, 2014 3:23 PM
80 Installing System Components
Figure 3-15. Removing and Installing the Cooling Shroud
Installing the Cooling Shroud
1
Align the holes on the cooling shroud with the alignment guides on the
system fan.
2
Hold the touch points on the cooling shroud and carefully lower the
cooling shroud into the system. Ensure that no cables are under the edges
of the cooling shroud.
3
Replace the expansion-card stabilizer. See "Installing the Expansion-Card
Stabilizer" on page 78.
4
Close the system. See "Closing the System" on page 60.
1 cooling shroud 2 expansion-card stabilizer
3 release tab 4 cooling shroud touch points (2)
1
4
3
2
Coaster_HOM.book Page 80 Monday, November 3, 2014 3:23 PM
Installing System Components 81
Expansion Cards
Expansion Card Installation Guidelines
Your system supports up to four PCIe Generation 2 cards. To identify the
expansion slots, see Figure 6-1.
Observe the following notes and guidelines regarding the expansion-card
slots:
• The expansion-card slots are not hot-swappable.
• PCI Express Generation 2 and Generation 1 expansion cards are supported
in all slots.
• Slot 2 supports full-length expansion cards; slots 1, 3, and 4 support half-
length expansion cards.
• The system supports up to two SAS or PERC expansion cards to manage
external storage.
CAUTION: To ensure proper cooling, no more than two of the four expansion
cards can have a power consumption of greater than 15 W (up to 25 W maximum
each), not including the integrated storage controller card.
• Table 3-1 provides a guide for installing expansion cards to ensure proper
cooling and mechanical fit. The expansion cards with the highest priority
should be installed first using the slot priority indicated. All other
expansion cards should be installed in card priority and slot priority order.
Coaster_HOM.book Page 81 Monday, November 3, 2014 3:23 PM
82 Installing System Components
1. When available.
2. Maximum of 2 of any card whose maximum power exceeds 15 W.
3. Refer to the expansion card documentation to ensure that the maximum power does not
exceed 15 W.
See Figure 6-1 for the location of the expansion card slots.
NOTE: Your system supports only one RAID card. You can install either of the above
mentioned RAID cards in Slot 1. The size of the expansion card connectors for the
PCI x8 card is PCI x8.
Removing an Expansion Card
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
2
Open the system. See "Opening the System" on page 59.
3
Remove the expansion card stabilizer. See "Removing the Expansion-Card
Stabilizer" on page 78.
Table 3-1. Expansion-Card Installation Priority
Card
Priority
Card Type Slot
Priority
Max
Allowed
25-W Card
1 SAS 6/iR controller 1 1 Y
2 S300 controller 1 1 Y
3 H200 controller111Y
4 SAS 5/E controller 1, 2 2 Y
5 6-Gbps SAS HBA11, 2 2 Y
6 LSI2032 PCIe HBA SCSI Adapter 3, 1, 2 3 Y
7Dual port NICs 3, 1, 23
2N3
8 Single port NICs 4, 3, 1, 2 41N2
Coaster_HOM.book Page 82 Monday, November 3, 2014 3:23 PM
Installing System Components 83
4
Disconnect all cables from the card.
5
Open the expansion-card latch. See Figure 3-16.
6
Grasp the expansion card by its edges, and carefully remove it from the
expansion-card connector.
7
If you are removing the card permanently, install a metal filler bracket over
the empty expansion slot opening and close the expansion-card latch.
NOTE: Filler brackets must be installed over empty expansion card slots to
maintain Federal Communications Commission (FCC) certification of the
system. The brackets also keep dust and dirt out of the system and aid in
proper cooling and airflow inside the system.
8
Replace the expansion card stabilizer. See "Installing the Expansion-Card
Stabilizer" on page 78.
9
Close the system. See "Closing the System" on page 60.
10
Reconnect the system and peripherals to their power sources, and turn
them on.
11
Remove the card’s device driver from the operating system.
Coaster_HOM.book Page 83 Monday, November 3, 2014 3:23 PM
84 Installing System Components
Figure 3-16. Removing and Installing an Expansion Card
Installing an Expansion Card
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Unpack the expansion card and prepare it for installation.
For instructions, see the documentation accompanying the card.
2
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
1 expansion card 2 expansion-card stabilizer
3 expansion-card latch 4 release tab
5 expansion-card slots
2
4
3
1
5
Coaster_HOM.book Page 84 Monday, November 3, 2014 3:23 PM
Installing System Components 85
3
Open the system. See "Opening the System" on page 59.
4
Remove the expansion card stabilizer. See "Removing the Expansion-Card
Stabilizer" on page 78.
5
Open the expansion-card latch and remove the filler bracket. See
Figure 3-16.
NOTE: Keep this bracket in case you need to remove the expansion card.
Filler brackets must be installed over empty expansion-card slots to maintain
FCC certification of the system. The brackets also keep dust and dirt out of the
system and aid in proper cooling and airflow inside the system.
6
Holding the card by its edges, position the card so that the card-edge
connector aligns with the expansion-card connector on the expansion-card
riser.
7
Insert the card-edge connector firmly into the expansion-card connector
until the card is fully seated.
8
Close the expansion-card latch. See Figure 3-16.
9
Connect all cables to the expansion card.
10
Replace the expansion-card stabilizer. See "Installing the Expansion-Card
Stabilizer" on page 78.
11
Close the system. See "Closing the System" on page 60.
SAS Controller Expansion Card
Read the installation instructions in the documentation for your SAS
controller card. Install the card in the expansion card connector (see
"Installing an Expansion Card" on page 84), and connect the hard-drive
activity indicator cable from the card to the HD_ACT_CARD (AUXLED1)
connector on the system board (see Figure 6-1 to locate the connector).
Secure the cables to the slots to manage the slack.
For information on connecting hard drives, see "Hard Drives" on page 70.
Coaster_HOM.book Page 85 Monday, November 3, 2014 3:23 PM
86 Installing System Components
System Memory
Your system supports DDR3 ECC unbuffered memory modules (UDIMMs).
The DIMMs can be 1066 or 1333 MHz. Single and dual-rank DIMMs can be
1066 or 1333 MHz.
The system contains four memory sockets, each two-socket set is organized
into two channels. The first socket of each channel is marked with white
release levers.
General Memory Module Installation Guidelines
To ensure optimal performance of your system, observe the following general
guidelines when configuring your system memory.
NOTE: Memory configurations that fail to observe these guidelines can prevent
your system from starting or producing any video output.
• Except for memory channels that are unused, all populated memory
channels must have identical configurations.
• Memory modules are installed in the numeric order of the sockets
beginning with DIMM_A1 or DIMM_B1.
• One or two DIMMs per channel can support up to 1333 MHz.
• If memory modules with different speeds are installed, they operate at the
speed of the slowest installed memory module(s).
Mode-Specific Guidelines
Your system supports both single-channel and dual-channel mode. A minimal
single-channel configuration of one 1 GB memory module is also supported
in this mode.
Table 3-2 shows sample memory configurations that follow the appropriate
memory guidelines stated in this section. The samples show identical
memory-module configurations and their the physical and available memory
totals. The table does not show mixed memory-module configurations, nor
do they address the memory speed considerations of any configuration.
Coaster_HOM.book Page 86 Monday, November 3, 2014 3:23 PM
Installing System Components 87
Table 3-2. Sample UDIMM Memory Configurations
Memory Module
Size
Memory Sockets Single Processor
1
3
2
4
Physical Memory (GB)
1 GB X
X
X
X
XX
1
2
4
2 GB X
X
XX
X
XX
2
4
8
4 GB X
X
XX
X
XX
4
8
16
8GB X
X
XX
X
XX
8
16
32
Coaster_HOM.book Page 87 Monday, November 3, 2014 3:23 PM
88 Installing System Components
Removing Memory Modules
WARNING: The memory modules are hot to touch for some time after the system
has been powered down. Allow time for the memory modules to cool before
handling them. Handle the memory modules by the card edges and avoid touching
the components on the memory module.
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
CAUTION: To ensure proper system cooling, memory-module blanks must be
installed in any memory socket that is not occupied. Install a memory-module
blank if you are removing a memory module and do not intend to install a
replacement.
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet and peripherals.
2
Open the system. See "Opening the System" on page 59.
3
Remove the expansion-card stabilizer. See "Removing the Expansion-Card
Stabilizer" on page 78.
4
Remove the cooling shroud. See "Removing the Cooling Shroud" on
page 79.
5
Locate the memory module sockets. See Figure 6-1.
CAUTION: Handle each memory module only by the card edges, ensuring not to
touch the components on the module.
6
Press down and out on the ejectors on each end of the socket until the
memory module pops out of the socket. See Figure 3-17.
7
Replace any removed memory modules with memory-module blanks to
ensure proper system cooling. See "Installing Memory Modules" on
page 89 for installation instructions.
8
Replace the cooling shroud. See "Installing the Cooling Shroud" on
page 80.
9
Close the system. See "Closing the System" on page 60.
Coaster_HOM.book Page 88 Monday, November 3, 2014 3:23 PM
Installing System Components 89
Figure 3-17. Installing and Removing a Memory Module
Installing Memory Modules
WARNING: The memory modules are hot to touch for some time after the system
has been powered down. Allow time for the memory modules to cool before
handling them. Handle the memory modules by the card edges and avoid touching
the components on the memory module.
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
CAUTION: To ensure proper system cooling, memory-module blanks must be
installed in any memory socket that is not occupied. Remove memory-module
blanks only if you intend to install memory in those sockets.
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet and peripherals.
2
Open the system. See "Opening the System" on page 59.
1 memory module 2 memory module socket ejectors (2)
3 alignment key
2
1
3
Coaster_HOM.book Page 89 Monday, November 3, 2014 3:23 PM
90 Installing System Components
3
Remove the expansion-card stabilizer. See "Removing the Expansion-Card
Stabilizer" on page 78.
4
Remove the cooling shroud. See "Removing the Cooling Shroud" on
page 79.
5
Locate the memory module sockets. See Figure 6-1.
6
Remove the memory-module blanks from the sockets in which you plan to
install memory modules.
7
Press out the ejectors on each end of the socket until the memory-module
blank pops out of the socket. See Figure 3-17.
NOTE: Make sure to retain any removed memory-module blanks for future
use.
8
Handle each memory module only on either card edge, ensuring not to
touch the middle of the memory module.
9
Align the memory module's edge connector with the alignment key of the
memory module socket, and insert the memory module in the socket.
NOTE: The memory module socket has an alignment key that allows you to
install the memory module in the socket in only one way.
10
Press down on the memory module with your thumbs until the socket
levers latch into a locked position.
When the memory module is properly seated in the socket, the levers on
the memory module socket align with the levers on the other sockets that
have memory modules installed.
11
Repeat step 6 through step 10 of this procedure to install the remaining
memory modules. See
Table 3-2
.
12
Replace the expansion-card stabilizer. See "Installing the Expansion-Card
Stabilizer" on page 78.
13
Replace the cooling shroud. See "Installing the Cooling Shroud" on
page 80.
14
Close the system. See "Closing the System" on page 60.
15
Reconnect the system and peripherals to their power sources, and turn
them on.
16
Press <F2> to enter the System Setup program, and check the
System
Memory
setting on the main System Setup screen.
Coaster_HOM.book Page 90 Monday, November 3, 2014 3:23 PM
Installing System Components 91
The system should have already changed the value to reflect the newly
installed memory.
17
If the value is incorrect, one or more of the memory modules may not be
installed properly. Repeat step 6 through step 10 of this procedure,
checking to ensure that the memory modules are firmly seated in their
sockets.
18
Run the system memory test in the system diagnostics. See "Running the
Embedded System Diagnostics" on page 128.
Processor
Removing the Processor
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Prior to upgrading your system,
download the latest system BIOS version
from support.dell.com and follow the instructions included in the
compressed download file to install the update on your system
.
2
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet. When disconnected from AC power,
press and hold the power button for 3 seconds to fully drain the system of
stored power prior to removing the cover.
NOTE: It is recommended that you always use a static mat and wrist grounding
strap while working on components in the interior of the system.
3
Open the system. See "Opening the System" on page 59.
4
Remove the expansion card stabilizer. See "Removing the Expansion-Card
Stabilizer" on page 78.
5
Remove the cooling shroud. See "Removing the Cooling Shroud" on
page 79.
WARNING: The heat sink and processor are hot to touch for some time after the
system has been powered down. Allow the heat sink and processor to cool before
handling them.
Coaster_HOM.book Page 91 Monday, November 3, 2014 3:23 PM
92 Installing System Components
CAUTION: Never remove the heat sink from a processor unless you intend to
remove the processor. The heat sink is necessary to maintain proper thermal
conditions.
6
Using a #2 Phillips screwdriver, loosen one of the heat-sink retention
screws. See Figure 3-18.
7
Wait 30 seconds for the heat sink to loosen from the processor.
8
Repeat step 6 and step 7 to loosen the other three heat-sink retention
screws.
9
Gently lift the heat sink off of the processor and set the heat sink aside
upside down (thermal grease side facing up).
Figure 3-18. Installing and Removing the Heat Sink
CAUTION: The processor is held in its socket under strong pressure. Be aware
that the release lever can spring up suddenly if not firmly grasped.
1 heat sink 2 heat-sink retention screws (4)
1
2
Coaster_HOM.book Page 92 Monday, November 3, 2014 3:23 PM
Installing System Components 93
10
Position your thumb firmly over the processor socket-release lever and
release the lever from the locked position by pushing down and pulling out
from under the tab. Rotate the lever 90 degrees upward until the processor
is released from the socket. See Figure 3-19.
11
Use the tab on the processor shield to rotate shield upward and out of the
way. See Figure 3-19.
Figure 3-19. Removing a Processor
1 socket-release lever 2 processor
3 notches in processor (2) 4 processor shield
5 ZIF socket 6 socket keys (2)
2
3
4
5
6
1
Coaster_HOM.book Page 93 Monday, November 3, 2014 3:23 PM
94 Installing System Components
CAUTION: Be careful not to bend any of the pins on the ZIF socket when removing
the processor. Bending the pins can permanently damage the system board.
12
Carefully, lift the processor out of the socket and leave the release lever up
so that the socket is ready for the new processor.
Installing a Processor
1
Unpack the new processor.
2Align the
p
rocessor with the
socket keys on t
he ZIF socket. See
Figure 3-19.
CAUTION: Positioning the processor incorrectly can permanently damage the
system board or the processor. Be careful not to bend the pins in the socket.
3
With the release lever on the processor socket in the open position, a
lign
the
p
rocessor with
the
socket
keys
and set the processor lightly in the
socket.
CAUTION: Do not use force to seat the processor. When the processor is
positioned correctly, it engages easily into the socket.
4
Close the processor shield.
5
R
otate the socket release lever down until it snaps into place.
6
Using a clean lint-free cloth, remove the thermal grease from the heat sink.
7
Open the grease packet included with your processor kit and apply thermal
grease evenly to the top of the new processor.
8Place the heat sink on the processor. See
Figure 3-19
.
9Using a #2 Phillips screwdriver, tighten the heat-sink retention screws.
See
Figure 3-18
.
10
Replace the cooling shroud. See "Installing the Cooling Shroud" on
page 80.
11
Replace the expansion-card stabilizer. See "Installing the Expansion-Card
Stabilizer" on page 78.
12
Close the system. See "Closing the System" on page 60.
13
Reconnect the system and peripherals to their power sources, and turn
them on.
Coaster_HOM.book Page 94 Monday, November 3, 2014 3:23 PM
Installing System Components 95
14
Press <F2> to enter the System Setup program, and check that the processor
information
matches the new system configuration. See "Entering the
System Setup Program" on page 36.
15
Run the system diagnostics to verify that the new processor operates
correctly. See "Running the Embedded System Diagnostics" on page 128
for information about running the diagnostics.
Cooling Fan
Your system has one cooling fan.
Removing the Cooling Fan
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
2
Open the system. See "Opening the System" on page 59.
3
Remove the expansion-card stabilizer. See "Removing the Expansion-Card
Stabilizer" on page 78.
4
Remove the cooling shroud. See "Removing the Cooling Shroud" on
page 79.
5
Disconnect the fan’s power cable from the system board.
6
Pull the fan release tab and slide the fan out of the securing slots on the
chassis, and lift the fan out.
Coaster_HOM.book Page 95 Monday, November 3, 2014 3:23 PM
96 Installing System Components
Figure 3-20. Removing and Installing the Cooling Fan
Installing the Cooling Fan
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Align the tabs on the system fan with the securing slots on the chassis.
2
Slide the system fan into the securing slots until the tabs lock into place.
3
Connect the fan cable to the system board. See Figure 6-1 for the location
of the connector.
1 release tab 2 securing tabs
3 power cable
2
1
3
Coaster_HOM.book Page 96 Monday, November 3, 2014 3:23 PM
Installing System Components 97
4
Replace expansion card stabilizer. See "Installing the Expansion-Card
Stabilizer" on page 78.
5
Replace the cooling shroud. See "Installing the Cooling Shroud" on
page 80.
6
Close the system. See "Closing the System" on page 60.
7
Reconnect the system to its electrical outlet and turn the system on,
including any attached peripherals.
System Battery
Replacing the System Battery
WARNING: There is a danger of a new battery exploding if it is incorrectly
installed. Replace the battery only with the same or equivalent type recommended
by the manufacturer. See your safety information for additional info.
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
2
Open the system. See "Opening the System" on page 59.
3
Locate the battery socket. See Figure 6-1.
CAUTION: To avoid damage to the battery connector, you must firmly support the
connector while installing or removing a battery.
4
To remove the system battery, push the metal tab away from the battery
until the battery pops out.
Coaster_HOM.book Page 97 Monday, November 3, 2014 3:23 PM
98 Installing System Components
Figure 3-21. Replacing the System Battery
5
To install the new system battery, hold the battery with the "+" facing up,
and aligned to the metal tab on the socket. Press the battery straight down
into the socket until it snaps into place.
6
Close the system. See "Closing the System" on page 60.
7
Enter the System Setup program to confirm that the battery is operating
properly. See "Using the System Setup Program and UEFI Boot Manager"
on page 35.
8
Enter the correct time and date in the System Setup program's
Time
and
Date
fields.
9
Exit the System Setup program.
1 positive side of battery connector 2 system battery
3 negative side of battery connector
2
3
1
Coaster_HOM.book Page 98 Monday, November 3, 2014 3:23 PM
Installing System Components 99
Power Supply
Removing the Power Supply
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
2
Open the system. See "Opening the System" on page 59.
3
Remove the expansion-card stabilizer. See "Removing the Expansion-Card
Stabilizer" on page 78.
4
Remove the cooling shroud. See "Removing the Cooling Shroud" on
page 79.
5
Disconnect all the power cables from the system board and drives.
NOTE: Note the routing of the DC power cables underneath the tabs in the
system frame as you release the tabs and remove the cables from the system
board and drives. You must route these cables properly when you replace
them to prevent their being pinched or crimped.
6
Remove the cables secured to the cable clip on the side of the power
supply.
7
Using a #2 Phillips screwdriver, remove the four screws that secure the
power supply to the back panel.
8
Press the power-supply release tab down and slide the power supply toward
the front of the system.
9
Lift the power-supply out of the chassis. See Figure 3-22.
10
Remove the cable clip and set it aside to attach to the new power supply.
Coaster_HOM.book Page 99 Monday, November 3, 2014 3:23 PM
100 Installing System Components
Figure 3-22. Removing the Power Supply
Installing the Power Supply
1
Attach the cable clip to the new power supply.
2
Align the power supply mounting holes with the mounting holes on the
back panel.
3
Slide the power supply toward the back panel until it snaps into place over
the power-supply release tab.
4
Using a #2 Phillips screwdriver, install the four screws that secure the
power supply to the back panel.
5
Secure the I/O panel and SATA cables (if present) to the routing clip on
the side of the power supply.
6
Connect all the power cables to the system board and drives.
7
Replace the cooling shroud. See "Installing the Cooling Shroud" on
page 80.
1 power supply 2 screws (4)
3 cable clip 4 power-supply release tab
3
1
2
4
Coaster_HOM.book Page 100 Monday, November 3, 2014 3:23 PM
Installing System Components 101
8
Replace the expansion-card stabilizer. See "Installing the Expansion-Card
Stabilizer" on page 78.
9
Close the system. See "Closing the System" on page 60.
Internal USB Memory Key
An optional USB memory key installed inside your system can be used as a
boot device, security key, or mass storage device.
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
2
Open the system. See "Opening the System" on page 59.
3
Locate the USB connector on the system board. See Figure 6-1.
4
Insert the USB memory key into the USB connector. See Figure 3-23.
5
Close the system. See "Closing the System" on page 60.
6
Enter the System Setup program and verify that the USB key has been
detected by the system. See"Using the System Setup Program and UEFI
Boot Manager" on page 35.
The USB connector must be enabled by the
Internal USB Port
option in
the
Integrated Devices
screen of the System Setup program. See
"Integrated Devices Screen" on page 41.
To boot from the USB memory key, configure the USB memory key with
a boot image and then specify the USB memory key in the boot
sequence in the System Setup program.
Coaster_HOM.book Page 101 Monday, November 3, 2014 3:23 PM
102 Installing System Components
Figure 3-23. Removing or Installing a USB Memory Key
Chassis Intrusion Switch
Removing the Chassis Intrusion Switch
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
2
Open the system. See "Opening the System" on page 59.
3
Disconnect the chassis intrusion switch cable from the INTRUSION
connector on the system board. See Figure 6-1.
4
Slide the chassis intrusion switch out of the securing bracket notch. See
Figure 3-24.
1 USB memory key 2 USB memory key connector
1
2
Coaster_HOM.book Page 102 Monday, November 3, 2014 3:23 PM
Installing System Components 103
5
Remove the switch and its attached cable from the system.
Figure 3-24. Removing and Installing the Chassis Intrusion Switch
Installing the Chassis Intrusion Switch
1
Align the chassis intrusion switch with the securing bracket notch. See
Figure 3-24.
2
Slide the switch into the securing bracket notch.
3
Connect the switch cable to the INTRUSION connector on the system
board. See Figure 6-1.
4
Close the system. See "Closing the System" on page 60.
1 chassis intrusion switch 2 securing bracket notch
3 INTRUSION connector
1
2
3
Coaster_HOM.book Page 103 Monday, November 3, 2014 3:23 PM
104 Installing System Components
Control Panel Assembly
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
Removing the Control Panel Assembly
1
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
2
Open the system. See "Opening the System" on page 59.
3
Remove the front bezel. See "Removing the Front Bezel" on page 61.
4
Disconnect the control panel cable from the system board:
CAUTION: Do not pull on the cable to unseat the connector. Doing so can damage
the cable.
a
Press the metal tabs on the ends of the cable connector.
b
Gently work the connector out of the socket.
5
Remove the screw holding the link bracket lock and lift the link bracket
lock out of the system.
Coaster_HOM.book Page 104 Monday, November 3, 2014 3:23 PM
Installing System Components 105
Figure 3-25. Removing the Link Bracket Lock
6
Remove the mounting screw holding the control panel assembly to the
front chassis. See Figure 3-26.
7
Lift the control panel assembly out of the system.
8
Disconnect the control panel cable from the control panel assembly:
CAUTION: Do not pull on the cable to unseat the connector. Doing so can damage
the cable.
a
Press the metal tabs on the ends of the cable connector.
b
Gently work the connector out of the socket.
1 link bracket lock
1
Coaster_HOM.book Page 105 Monday, November 3, 2014 3:23 PM
106 Installing System Components
Figure 3-26. Removing and Installing the Control Panel Assembly
Installing the Control Panel Assembly
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Connect the control panel cable to the control panel board.
2
Align the slot in the control panel board with the standoff on the chassis
and secure with the screw. See Figure 3-26.
3
Secure the link bracket lock by replacing the screw. See Figure 3-26.
4
Secure the control panel cable through the clips beneath the optional tape
or optical drive and on the side of the power supply unit.
1 mounting screw 2 control-panel board
3 control-panel cable 4 standoff
1
2
3
4
Coaster_HOM.book Page 106 Monday, November 3, 2014 3:23 PM
Installing System Components 107
5
Connect the control-panel cable to the system board.
6
Replace the front bezel. See "Installing the Front Bezel" on page 62.
7
Close the system. See "Closing the System" on page 60.
8
Reconnect the system to its electrical outlet and turn the system on,
including any attached peripherals.
System Board
Removing the System Board
WARNING: The heat sink can get hot during operation. To avoid burns, ensure
that the system has sufficient time to cool before removing the system board.
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
CAUTION: If you are using the Trusted Platform Module (TPM) with an encryption
program, you may be prompted to create a recovery key during system or program
setup. Be sure to create and safely store this recovery key. If you ever need to
replace the system board, you must supply the recovery key when you restart your
system or program before you can access the encrypted data on your hard drive(s).
1
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
2
Open the system. See "Opening the System" on page 59.
3
Remove expansion-card stabilizer. See "Removing the Expansion-Card
Stabilizer" on page 78.
4
Remove the cooling shroud. See "Removing the Cooling Shroud" on
page 79.
5
Disconnect all cables from the system board.
6
Remove the cooling fan. See "Removing the Cooling Fan" on page 95.
7
Remove all expansion cards and any attached cables. See "Removing an
Expansion Card" on page 82.
Coaster_HOM.book Page 107 Monday, November 3, 2014 3:23 PM
108 Installing System Components
8
Remove all memory modules. See "Removing Memory Modules" on
page 88.
CAUTION: The processor and heat sink can become extremely hot. Allow
sufficient time for the processor and heat sink to cool before handling.
9
Remove the processor heat sink. See "Removing the Processor" on page 91.
10
Using a #2 Phillips screwdriver, remove the ten screws securing the system
board to the chassis and then slide the system board toward the front end
of the chassis.
CAUTION: Do not lift the system board by grasping a memory module, processor,
or other components.
11
Grasp the system board by the edges of the system board and lift the
system board out of the chassis. See Figure 3-27.
Figure 3-27. Removing and Installing the System Board
1 screws (10) 2 system board
1
2
Coaster_HOM.book Page 108 Monday, November 3, 2014 3:23 PM
Installing System Components 109
Installing the System Board
1
Unpack the new system board.
2
Remove the labels from the processor shield and affix them to the system
identification panel on the front of the system. See Figure 3-27.
3
Holding the system board by its edges, lower the system board into the
chassis.
CAUTION: Do not lift the system board by grasping a memory module, processor,
or other components.
4
Slightly lift up the front of the system board and maneuver the system
board to the bottom of the chassis until it lays completely flat.
5
Push the system board toward the back of the chassis until the board is in
place.
6
Tighten the ten screws to secure the system board to the chassis. See
Figure 6-1.
7
Transfer the processor to the new system board. See "Removing the
Processor" on page 91 and "Installing a Processor" on page 94.
8
Replace all the memory modules and memory blanks. See "Installing
Memory Modules" on page 89.
9
Connect the cables in the order listed below (see Figure 6-1 for the
locations of the connectors on the system board):
• SATA interface cable, if applicable
• Control panel interface cable
• Optical/tape drive power cable
• System board power cables
10
Install all expansion cards. See "Installing an Expansion Card" on page 84.
11
Replace the cooling fan. See "Installing the Cooling Fan" on page 96.
12
Replace the heat sink. See "Installing a Processor" on page 94.
13
Replace the cooling shroud. See "Installing the Cooling Shroud" on
page 80.
14
Replace the expansion-card stabilizer. See "Installing the Expansion-Card
Stabilizer" on page 78.
15
Close the system. See "Closing the System" on page 60.
Coaster_HOM.book Page 109 Monday, November 3, 2014 3:23 PM
110 Installing System Components
16
Reconnect the system to its electrical outlet and turn the system on,
including any attached peripherals.
Coaster_HOM.book Page 110 Monday, November 3, 2014 3:23 PM
Troubleshooting Your System 111
4
Troubleshooting Your System
Safety First—For You and Your System
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
Troubleshooting System Startup Failure
If your system halts during startup prior to video output, especially after
installing an operating system or reconfiguring your system’s hardware, check
for the following conditions:
• If you boot the system to the BIOS boot mode after installing an operating
system from the UEFI Boot Manager, the system hangs. The reverse is also
true. You must boot to the same boot mode in which you installed the
operating system. See "Using the System Setup Program and UEFI Boot
Manager" on page 35.
• Invalid memory configurations could cause the system to halt at startup
without any video output. See "System Memory" on page 86.
For all other startup issues, note the system messages that appear onscreen.
See "System Messages" on page 19 for more information.
Troubleshooting External Connections
Ensure that all external cables are securely attached to the external
connectors on your system before troubleshooting any external devices. See
Figure 1-1 and Figure 1-2 for the front- and back-panel connectors on your
system.
Coaster_HOM.book Page 111 Monday, November 3, 2014 3:23 PM
112 Troubleshooting Your System
Troubleshooting the Video Subsystem
1
Check the system and power connections to the monitor.
2
Check the video interface cabling from the system to the monitor.
3
Run the appropriate online diagnostic test. See "Using Online Diagnostics"
on page 127.
If the tests run successfully, the problem is not related to video hardware.
If the tests fail, see "Getting Help" on page 135.
Troubleshooting a USB Device
Use the following steps to troubleshoot a USB keyboard/mouse. For other
USB devices, go to step 4.
1
Disconnect the keyboard and mouse cables from the system briefly and
reconnect them.
2
Connect the keyboard/mouse to the USB port(s) on the opposite side of
the system.
3
If the problem is resolved, restart the system, enter the System Setup
program, and check if the nonfunctioning USB ports are enabled.
4
Replace the keyboard/mouse with another working keyboard/mouse.
5
If the problem is resolved, replace the faulty keyboard/mouse.
6
If the problem is not resolved, proceed to the next step to begin
troubleshooting the other USB devices attached to the system.
7
Power down all attached USB devices and disconnect them from the
system.
8
Restart the system and, if your keyboard is functioning, enter the system
setup program. Verify that all USB ports are enabled. See "Integrated
Devices Screen" on page 41.
If your keyboard is not functioning, you can also use remote access. If the
system is not accessible, see "Disabling a Forgotten Password" on page 134
for instructions on setting the NVRAM_CLR jumper inside your system
and restoring the BIOS to the default settings.
9
Reconnect and power on each USB device one at a time.
Coaster_HOM.book Page 112 Monday, November 3, 2014 3:23 PM
Troubleshooting Your System 113
10
If a device causes the same problem, power down the device, replace the
USB cable, and power up the device.
If the problem persists, replace the device.
If all troubleshooting fails, see "Getting Help" on page 135.
Troubleshooting a Serial I/O Device
1
Turn off the system and any peripheral devices connected to the serial
port.
2
Swap the serial interface cable with a working cable, and turn on the
system and the serial device.
If the problem is resolved, replace the interface cable.
3
Turn off the system and the serial device, and swap the device with a
comparable device.
4
Turn on the system and the serial device.
If the problem is resolved, replace the serial device.
If the problem persists, see "Getting Help" on page 135.
Troubleshooting a NIC
1
Run the appropriate online diagnostic test. See "Using Online Diagnostics"
on page 127.
2
Restart the system and check for any system messages pertaining to the
NIC controller.
3
Check the appropriate indicator on the NIC connector:
• If the link indicator does not light, check all cable connections.
• If the activity indicator does not light, the network driver files might
be damaged or missing.
Remove and reinstall the drivers if applicable. See the NIC's
documentation.
• Change the autonegotiation setting, if possible.
• Use another connector on the switch or hub.
See "NIC Indicator Codes" on page 16.
Coaster_HOM.book Page 113 Monday, November 3, 2014 3:23 PM
114 Troubleshooting Your System
4
Ensure that the appropriate drivers are installed and the protocols are
bound. See the NIC's documentation.
5
Enter the System Setup program and confirm that the NIC ports are
enabled. See "Integrated Devices Screen" on page 41.
6
Ensure that the NICs, hubs, and switches on the network are all set to the
same data transmission speed and duplex. See the documentation for each
network device.
7
Ensure that all network cables are of the proper type and do not exceed the
maximum length.
If all troubleshooting fails, see "Getting Help" on page 135.
Troubleshooting a Wet System
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
2
Open the system. See "Opening the System" on page 59.
3
Disassemble components from the system. See "Installing System
Components" on page 57.
•Hard drives
• USB memory key
• Cooling shroud and expansion-card stabilizer
•Expansion cards
•Power supply
• Cooling fan
• Processor and heat sink
•Memory modules
4
Let the system dry thoroughly for at least 24 hours.
Coaster_HOM.book Page 114 Monday, November 3, 2014 3:23 PM
Troubleshooting Your System 115
5
Reinstall the components you removed in step 3.
6
Close the system. See "Closing the System" on page 60.
7
Turn on the system and attached peripherals.
If the system does not start properly, see "Getting Help" on page 135.
8
If the system starts properly, shut down the system and reinstall all of the
expansion cards that you removed. See "Installing an Expansion Card" on
page 84.
9
Run the appropriate online diagnostic test. See "Using Online Diagnostics"
on page 127.
If the tests fail, see "Getting Help" on page 135.
Troubleshooting a Damaged System
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
2
Open the system. See "Opening the System" on page 59.
3
Ensure that the following components are properly installed:
• Cooling shroud and expansion-card stabilizer
•Expansion cards
•Power supply
• Cooling fan
• Processor and heat sink
•Memory modules
• Hard-drive carriers
4
Ensure that all cables are properly connected.
5
Close the system. See "Closing the System" on page 60.
Coaster_HOM.book Page 115 Monday, November 3, 2014 3:23 PM
116 Troubleshooting Your System
6
Run the system board tests in the system diagnostics. See "Running the
System Diagnostics" on page 127.
If the tests fail,
see "Getting Help" on page 135.
Troubleshooting the System Battery
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
NOTE: If the system is turned off for long periods of time (for weeks or months), the
NVRAM may lose its system configuration information. This situation is caused by a
defective battery.
1
Re-enter the time and date through the System Setup program. See "Using
the System Setup Program and UEFI Boot Manager" on page 35.
2
Turn off the system and disconnect it from the electrical outlet for at least
one hour.
3
Reconnect the system to the electrical outlet and turn on the system.
4
Enter the System Setup program.
If the date and time are not correct in the System Setup program, replace
the battery. See "Replacing the System Battery" on page 97.
If the problem is not resolved by replacing the battery, see "Getting Help"
on page 135.
NOTE: Some software may cause the system time to speed up or slow down. If the
system seems to operate normally except for the time kept in the System Setup
program, the problem may be caused by software rather than by a defective
battery.
Coaster_HOM.book Page 116 Monday, November 3, 2014 3:23 PM
Troubleshooting Your System 117
Troubleshooting Power Supply
1
Reseat the power supply by removing and reinstalling it. See "Removing
the Power Supply" on page 99 and "Installing the Power Supply" on
page 100.
NOTE: After installing a power supply, allow several seconds for the system
to recognize the power supply and to determine if it is working properly.
If the problem persists, replace the faulty power supply.
2
If the problem persists, see "Getting Help" on page 135.
Troubleshooting System Cooling Problems
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
Ensure that none of the following conditions exist:
• System cover, cooling shroud, EMI filler panel, memory-module blank, or
back-filler bracket is removed.
• Ambient temperature is too high.
• External airflow is obstructed.
• The cooling fan is removed or has failed. See "Troubleshooting Cooling
Fan" on page 118.
• The expansion card installation guidelines have not been followed. See
"Expansion Card Installation Guidelines" on page 81.
Coaster_HOM.book Page 117 Monday, November 3, 2014 3:23 PM
118 Troubleshooting Your System
Troubleshooting Cooling Fan
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system and all attached peripherals.
2
Open the system. See "Opening the System" on page 59.
3
Reseat the fan's power cable.
4
Restart the system.
If the fan functions properly, close the system. See "Closing the System" on
page 60.
5
If the fan does not function, turn off the system and install a new fan. See
"Installing the Cooling Fan" on page 96.
6
Close the system. See "Closing the System" on page 60.
7
Restart the system.
If the problem is resolved, close the system. See "Closing the System" on
page 60.
If the replacement fan does not operate,
see "Getting Help" on page 135.
Coaster_HOM.book Page 118 Monday, November 3, 2014 3:23 PM
Troubleshooting Your System 119
Troubleshooting System Memory
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
NOTE: Invalid memory configurations can cause your system to halt at startup
without video output. See "General Memory Module Installation Guidelines" on
page 86 and verify that your memory configuration complies with all applicable
guidelines.
1
If the system is operational, run the appropriate online diagnostic test. See
"Using Online Diagnostics" on page 127.
If diagnostics indicates a fault, follow the corrective actions provided by
the diagnostic program.
2
If the system is not operational, turn off the system and attached
peripherals, and unplug the system from the power source. Wait at least 10
seconds and then reconnect the system to power.
3
Turn on the system and attached peripherals and note the messages on the
screen.
Go to step 12 if an error message appears indicating a fault with a specific
memory module.
4
Enter the System Setup program and check the system memory setting.
See "Memory Settings Screen" on page 39. Make any changes to the
memory settings, if needed.
If the memory settings match the installed memory but a problem is still
indicated, go to step 12.
5
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
6
Open the system. See "Opening the System" on page 59.
7
Check the memory channels and ensure that they are populated correctly.
See "General Memory Module Installation Guidelines" on page 86.
8
Reseat the memory modules in their sockets. See "Installing Memory
Modules" on page 89.
Coaster_HOM.book Page 119 Monday, November 3, 2014 3:23 PM
120 Troubleshooting Your System
9
Close the system. See "Closing the System" on page 60.
10
Enter the System Setup program and check the system memory setting.
See "Memory Settings Screen" on page 39.
If the problem is not resolved, proceed with the next step.
11
Open the system. See "Opening the System" on page 59.
12
If a diagnostic test or error message indicates a specific memory module as
faulty, swap or replace the module.
13
To troubleshoot an unspecified faulty memory module, replace the
memory module in the first DIMM socket with a module of the same type
and capacity. See "Installing Memory Modules" on page 89.
14
Close the system. See "Closing the System" on page 60.
15
As the system boots, observe any error message that appears and the
diagnostic indicators on the front of the system.
16
If the memory problem is still indicated, repeat step 12 through step 15 for
each memory module installed.
If the problem persists after all memory modules have been checked,
see
"Getting Help" on page 135
.
Troubleshooting an Internal USB Key
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Enter the System Setup program and ensure that the USB key port is
enabled. See "Integrated Devices Screen" on page 41.
2
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
3
Open the system. See "Opening the System" on page 59.
4
Locate the USB key and reseat it.
5
Close the system. See "Closing the System" on page 60.
Coaster_HOM.book Page 120 Monday, November 3, 2014 3:23 PM
Troubleshooting Your System 121
6
Turn on the system and attached peripherals and check if the USB key is
functioning.
7
If the problem is not resolved, repeat step 2 and step 3.
8
Insert a different USB key that you know works properly.
9
Close the system. See "Closing the System" on page 60.
If the problem is not resolved, see
"Getting Help" on page 135
.
Troubleshooting an Optical Drive
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Try using a different CD or DVD.
2
Enter the System Setup program and ensure that the integrated SATA
controller and the drive's SATA port are enabled. See "Using the System
Setup Program and UEFI Boot Manager" on page 35.
3
Run the appropriate online diagnostic test. See "Using Online Diagnostics"
on page 127.
4
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
5
Open the system. See "Opening the System" on page 59.
6
Remove the front bezel. See "Removing the Front Bezel" on page 61.
7
Ensure that the interface cable is securely connected to the optical drive
and to the controller.
8
Ensure that a power cable is properly connected to the drive.
9
Close the system. See "Closing the System" on page 60.
If the problem is not resolved,
see "Getting Help" on page 135
.
Coaster_HOM.book Page 121 Monday, November 3, 2014 3:23 PM
122 Troubleshooting Your System
Troubleshooting a Tape Backup Unit
1
Try using a different tape cartridge.
2
Ensure that the device drivers for the tape backup unit are installed and
are configured correctly. See your tape drive documentation for more
information about device drivers.
3
Reinstall the tape-backup software as instructed in the tape-backup
software documentation.
4
For external tape drives, ensure that the tape drive’s interface cable is fully
connected to the external port on the controller card. For internal tape
drives, check the cable connections:
a
Turn off the system and attached peripherals, and disconnect the
system from the electrical outlet.
b
Open the system. See "Opening the System" on page 59.
c
Reseat the controller card in the expansion card slot.
d
Ensure that the tape drive's interface cable is fully connected to the
tape drive and to the connector on the controller card (SAS or SCSI).
e
Ensure that a power cable is properly connected to the drive and to
the system board.
f
Close the system. See "Closing the System" on page 60.
5
For SCSI tape drives, verify that the tape drive is configured for a unique
SCSI ID number and that the tape drive is terminated or not terminated,
based on the interface cable used to connect the drive.
See the documentation for the tape drive for instructions on selecting the
SCSI ID number and enabling or disabling termination.
6
Run the appropriate online diagnostics tests. See "Using Online
Diagnostics" on page 127.
If you cannot resolve the problem, see
"Getting Help" on page 135
.
Coaster_HOM.book Page 122 Monday, November 3, 2014 3:23 PM
Troubleshooting Your System 123
Troubleshooting a Hard Drive
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
CAUTION: This troubleshooting procedure can destroy data stored on the hard
drive. Before you proceed, back up all files on the hard drive.
1
Run the appropriate online diagnostics test. See "Using Online
Diagnostics" on page 127.
Depending on the results of the diagnostics test, proceed as needed
through the following steps.
2
If your system has a RAID controller and your hard drives are configured in
a RAID array, perform the following steps:
a
Restart the system and enter the host adapter configuration utility
program by pressing <Ctrl><R> for a PERC controller or
<Ctrl><C> for a SAS controller.
See the documentation supplied with the host adapter for information
about the configuration utility.
b
Ensure that the hard drive(s) have been configured correctly for the
RAID array.
c
Take the hard drive offline and reseat the drive.
d
Exit the configuration utility and allow the system to boot to the
operating system.
3
Ensure that the required device drivers for your controller card are installed
and are configured correctly. See the operating system documentation for
more information.
4
Restart the system, enter the System Setup program, and verify that the
controller is enabled and the drives appear in the System Setup program.
See "Using the System Setup Program and UEFI Boot Manager" on
page 35.
If the problem persists, see "Troubleshooting Expansion Cards" on
page 124.
Coaster_HOM.book Page 123 Monday, November 3, 2014 3:23 PM
124 Troubleshooting Your System
Troubleshooting Expansion Cards
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
NOTE: When troubleshooting an expansion card, see the documentation for your
operating system and the expansion card.
1
Run the appropriate online diagnostic test. See "Using Online Diagnostics"
on page 127.
2
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
3
Open the system. See "Opening the System" on page 59.
4
Ensure that each expansion card is firmly seated in its connector. See
"Installing an Expansion Card" on page 84.
5
Close the system. See "Closing the System" on page 60.
6
If the problem is not resolved, turn off the system and attached
peripherals, and disconnect the system from the electrical outlet.
7
Open the system. See "Opening the System" on page 59.
8
Remove all expansion cards installed in the system. See "Removing an
Expansion Card" on page 82.
9
Close the system. See "Closing the System" on page 60.
10
Run the appropriate online diagnostic test.
If the tests fail, see "Getting Help" on page 135.
11
For each expansion card you removed in step 8, perform the following
steps:
a
Turn off the system and attached peripherals, and disconnect the
system from the electrical outlet.
b
Open the system. See "Opening the System" on page 59.
c
Reinstall one of the expansion cards.
d
Close the system. See "Closing the System" on page 60.
Coaster_HOM.book Page 124 Monday, November 3, 2014 3:23 PM
Troubleshooting Your System 125
e
Run the appropriate diagnostic test.
If the tests fail, see "Getting Help" on page 135.
Troubleshooting the Processor
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Run the appropriate online diagnostics test. See "Using Online
Diagnostics" on page 127.
2
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
3
Open the system. See "Opening the System" on page 59.
4
Ensure that the processor and heat sink are properly installed. See
"Installing a Processor" on page 94.
5
Close the system. See "Closing the System" on page 60.
6
Run the appropriate online diagnostic test.
If a problem is still indicated, see "Getting Help" on page 135.
Coaster_HOM.book Page 125 Monday, November 3, 2014 3:23 PM
126 Troubleshooting Your System
Coaster_HOM.book Page 126 Monday, November 3, 2014 3:23 PM
Running the System Diagnostics 127
5
Running the System Diagnostics
If you experience a problem with your system, run the diagnostics before
calling for technical assistance. The purpose of the diagnostics is to test your
system's hardware without requiring additional equipment or risking data
loss. If you are unable to fix the problem yourself, service and support
personnel can use diagnostics test results to help you solve the problem.
Using Online Diagnostics
To assess a system problem, first use the Online Diagnostics. Online
Diagnostics is a suite of diagnostic programs, or test modules, that include
diagnostic tests on chassis and storage components such as hard drives,
physical memory, communications and printer ports, NICs, CMOS, and
more. If you are unable to identify the problem using the online diagnostics,
then use the embedded system diagnostics.
The files required to run the online diagnostics for systems running supported
Microsoft Windows and Linux operating systems are available at
support.dell.com and on the media that came with your system. For
information about using diagnostics, see the Dell Online Diagnostics User's
Guide.
Embedded System Diagnostics Features
The system diagnostics provides a series of menus and options for particular
device groups or devices. The system diagnostics menus and options allow
you to:
• Run tests individually or collectively
• Control the sequence of tests
• Repeat tests
• Display, print, or save test results
• Temporarily suspend testing if an error is detected or terminate testing
when a user-defined error limit is reached
• View help messages that briefly describe each test and its parameters
Coaster_HOM.book Page 127 Monday, November 3, 2014 3:23 PM
128 Running the System Diagnostics
• View status messages that inform you if tests are completed successfully
• View error messages that inform you of problems encountered during
testing
When to Use the Embedded System Diagnostics
If a major component or device in the system does not operate properly,
component failure may be indicated. As long as the processor and the
system's input/output devices are functioning, you can use the embedded
system diagnostics to help identify the problem.
Running the Embedded System Diagnostics
The embedded system diagnostics program is run from the Dell USC screen.
CAUTION: Use the embedded system diagnostics to test only your system. Using
this program with other systems may cause invalid results or error messages.
1
As the system boots, press <F10>.
2
Click
Diagnostics
in the left pane and click
Launch Diagnostics
in the
right pane.
The Diagnostics menu allows you to run all or specific diagnostics tests or to
exit.
System Diagnostics Testing Options
Click the testing option in the Main Menu window.
Testing Option Function
Express Test Performs a quick check of the system. This option runs
device tests that do not require user interaction.
Extended Test Performs a more thorough check of the system. This test
can take an hour or longer.
Custom Test Tests a particular device.
Information Displays test results.
Coaster_HOM.book Page 128 Monday, November 3, 2014 3:23 PM
Running the System Diagnostics 129
Using the Custom Test Options
When you select Custom Test in the Main Menu window, the Customize
window allows you to select the device(s) to be tested, select specific options
for testing, and view the test results.
Selecting Devices for Testing
The left side of the Customize window lists devices that can be tested. Click
(+) next to a device or module to view its components. Click (+) on any
component to view the tests that are available. Clicking a device, rather than
its components, selects all of the components of the device for testing.
NOTE: After you select all the devices and components that you want to test,
highlight All Devices and then click Run Tests.
Selecting Diagnostics Options
From the Diagnostics Options area, select the test(s) you want to run on a
device. You can select:
•
Non-Interactive Tests Only
—Runs only tests that require no user
intervention.
•
Quick Tests Only
—Runs only the quick tests on the device.
•
Show Ending Timestamp
—Time stamps the test log.
•
Test Iterations
—Selects the number of times the test is run.
•
Log output file pathname
—Enables you to specify the USB memory key
where the test log file is saved. You cannot save the file to a hard drive.
Coaster_HOM.book Page 129 Monday, November 3, 2014 3:23 PM
130 Running the System Diagnostics
Viewing Information and Results
The following tabs in the Customize window provide information about the
test and the test results:
•
Results
—Displays the test that ran and the result.
•
Errors
—Displays any errors that occurred during the test.
•
Help
—Displays information about the currently selected device,
component, or test.
•
Configuration
—Displays basic configuration information about the
currently selected device.
•
Parameters
—Displays parameters that you can set for the test.
Coaster_HOM.book Page 130 Monday, November 3, 2014 3:23 PM
Jumpers and Connectors 131
6
Jumpers and Connectors
System Board Jumper
For information on resetting the password jumper to disable a password, see
"Disabling a Forgotten Password" on page 134.
Table 6-1. System Board Jumper Settings
Jumper Setting Description
PWRD_EN (default) The password feature is enabled
(pins 2–4)
The password feature is disabled
(pins 4–6)
NVRAM_CLR (default) The configuration settings are retained at system
boot (pins 3–5)
The configuration settings are cleared at the next
system boot (pins 1–3)
Coaster_HOM.book Page 131 Monday, November 3, 2014 3:23 PM
132 Jumpers and Connectors
System Board Connectors
Figure 6-1. System Board Jumpers and Connectors
Table 6-2. System Board Jumpers and Connectors
Item Connector Description
1 USB USB connectors (4)
2 SATA_F eSATA eSATA connector
3 COM Serial connector
4VGA Video connector
25
11
1 2 3
20
4
10
78 9
13
6
12
14
26
19
18
17
16
21
22
27
24
23
5
15
Coaster_HOM.book Page 132 Monday, November 3, 2014 3:23 PM
Jumpers and Connectors 133
5 NIC NIC connector
6 FAN System fan connector
7 SLOT1 PCIE_G2_X8 PCIe x8 half length
8 SLOT2 PCIE_G2_X8 PCIe x8 full length
9 SLOT3 PCIE_G2_X4 PCIe x4 half length
10 BATTERY Battery socket
11 SLOT4 PCIE_G2_X1 PCIe x1 half length
12 HD_ACT_CARD Auxiliary hard-drive LED
13 INT_USB1 and INT_USB2 Internal USB key 1 and 2
14 CPU Processor
15 POWER12V Power connector 12 V
16 DIMM_B1 DIMM_B1 memory module slot
17 DIMM_B2 DIMM_B2 memory module slot
18 DIMM_A1 DIMM_A1 memory module slot
19 DIMM_A2 DIMM_A2 memory module slot
20 CTRL_PNL Control panel connector
21 SATA_B SATA drive
22 SATA_A SATA drive
23 SATA_C SATA drive
24 SATA_D SATA drive/optical drive
25 PWR_CONN Power connector
26 INTRUSION Intrusion switch connector
27 SATA_E ODD SATA optical drive
Table 6-2. System Board Jumpers and Connectors
Item Connector Description
Coaster_HOM.book Page 133 Monday, November 3, 2014 3:23 PM
134 Jumpers and Connectors
Disabling a Forgotten Password
The system's software security features include a system password and a setup
password, which are discussed in detail in "Using the System Setup Program
and UEFI Boot Manager" on page 35. The password jumper enables these
password features or disables them and clears any password(s) currently in
use.
CAUTION: See "Protecting Against Electrostatic Discharge" in the safety
instructions that came with the system.
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
2
Open the system. See "Opening and Closing the System" on page 59.
3
Remove the jumper plug from the password jumper.
See Figure 6-1 to locate the password jumper (labeled "PWRD_EN") on
the system board.
4
Close the system. See "Closing the System" on page 60.
5
Place the system upright on a flat, stable surface.
6
Reconnect the system to its electrical outlet and turn the system on,
including any attached peripherals.
The existing passwords are not disabled (erased) until the system boots
with the password jumper plug removed. However, before you assign a new
system and/or setup password, you must install the jumper plug.
NOTE: If you assign a new system and/or setup password with the jumper
plug still removed, the system disables the new password(s) the next time it
boots.
7
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
8
Open the system. See "Opening and Closing the System" on page 59.
9
Install the jumper plug on the password jumper.
10
Close the system. See "Closing the System" on page 60.
11
Assign a new system and/or setup password.
To assign a new password using the System Setup program, see "Assigning
a System Password" on page 49.
Coaster_HOM.book Page 134 Monday, November 3, 2014 3:23 PM
Getting Help 135
7
Getting Help
Contacting Dell
For customers in the United States, call 800-WWW-DELL (800-999-3355).
NOTE: If you do not have an active Internet connection, you can find contact
information on your purchase invoice, packing slip, bill, or Dell product catalog.
Dell provides several online and telephone-based support and service options.
Availability varies by country and product, and some services may not be
available in your area. To contact Dell for sales, technical support, or
customer service issues:
1
Visit
support.dell.com
.
2
Verify your country or region in the
Choose A Country/Region
drop-down
menu at the bottom of the page.
3
Click
Contact Us
on the left side of the page.
4
Select the appropriate service or support link based on your need.
5
Choose the method of contacting Dell that is convenient for you.
Coaster_HOM.book Page 135 Monday, November 3, 2014 3:23 PM
136 Getting Help
Coaster_HOM.book Page 136 Monday, November 3, 2014 3:23 PM
Index 137
Index
Numerics
5.25-inch drive
installing, 68
B
battery
installing, 97
troubleshooting, 116
battery (system)
replacing, 97
BMC
configuring, 53
C
cable clip, 100
CD drive
troubleshooting, 121
CD/DVD drive
installing, 68
removing, 65
chassis intrusion switch
installing, 103
removing, 102
replacing, 103
closing the system, 60
connectors
USB, 12, 14
video, 12, 14
contacting Dell, 135
cooling fan
installing, 96
removing, 95
replacing, 96
troubleshooting, 118
D
damaged systems
troubleshooting, 115
Dell
contacting, 135
Dell PowerEdge Diagnostics
using, 127
diagnostics
advanced testing options, 129
testing options, 128
using Dell PowerEdge
Diagnostics, 127
when to use, 128
DIMM
sockets, 86
DVD drive. See CD/DVD drive.
Coaster_HOM.book Page 137 Monday, November 3, 2014 3:23 PM
138 Index
E
error messages, 36
expansion cards, 81
installing, 84
removing, 82
replacing, 84
troubleshooting, 124
F
front bezel
insert, 62
removing, 61
replacing, 62
front panel
features, 12
front-panel features, 12
G
guidelines
connecting external devices, 15
memory installation, 86
H
hard drive
installing, 72, 76
removing, 70, 74
troubleshooting, 123
I
I/O panel
installing, 106
removing, 104
replacing, 106
iDRAC Configuration Utility, 54
indicators
front-panel, 12
NIC, 16
power, 12
insert on front bezel
removing, 62
replacing, 63
installing
5.25-inch drive, 68
CD/DVD drive, 68
chassis intrusion switch, 103
cooling fan, 96
expansion cards, 84
hard drive, 72, 76
I/O panel, 106
memory modules, 89
power supply, 100
processor, 94
system battery, 97
system board, 109
tape drive, 68
K
keyboards
troubleshooting, 112
Coaster_HOM.book Page 138 Monday, November 3, 2014 3:23 PM
Index 139
M
memory
branches, 86
channels, 86
troubleshooting, 119
memory key connector
(USB), 101
memory modules (DIMMs)
configuring, 86
installing, 89
removing, 88
messages
error messages, 36
system, 19
warning, 32
N
NIC
indicators, 16
NICs
troubleshooting, 113
O
opening the system, 59
options
system setup, 37
P
password
disabling, 134
setup, 52
system, 49
phone numbers, 135
POST
accessing system features, 11
power indicators, 12
power supplies
troubleshooting, 117
power supply
installing, 100
removing, 99
replacing, 100
processor
installing, 94
removing, 91
troubleshooting, 125
R
recommended tools, 57
removing
CD/DVD drive, 65
chassis intrusion switch, 102
cooling fan, 95
expansion cards, 82
front bezel, 61
hard drive, 70, 74
I/O panel, 104
memory modules, 88
power supply, 99
processor, 91
system board, 107
Coaster_HOM.book Page 139 Monday, November 3, 2014 3:23 PM
140 Index
tape drive, 65
replacing
chassis intrusion switch, 103
cooling fan, 96
expansion cards, 84
front bezel, 62
I/O panel, 106
power supply, 100
system battery, 97
system board, 109
S
safety, 111
SAS controller card
installing, 85
SAS hard drive. See hard drive.
SATA hard drive. See hard drive.
securing your system, 45, 51
setup password, 52
startup
accessing system features, 11
support
contacting Dell, 135
system
closing, 60
opening, 59
system board
installing, 109
removing, 107
replacing, 109
system cooling
troubleshooting, 117
system features
accessing, 11
system messages, 19
system password, 49
system setup
options, 37
system setup program
boot settings, 41
entering, 36
integrated devices options, 41
keystroke, 36
memory settings, 39
PCI IRQ assignments, 42
power management options, 44
processor settings, 39
SATA settings, 40
serial communications
options, 43
system security options, 45
system setup screens
main, 37
system startup failure, 111
T
tape drive
installing, 68
removing, 65
telephone numbers, 135
TPM security, 45
troubleshooting
Coaster_HOM.book Page 140 Monday, November 3, 2014 3:23 PM
Index 141
battery, 116
CD drive, 121
cooling fan, 118
damaged system, 115
expansion cards, 124
external connections, 111
hard drive, 123
internal USB key, 120
keyboard, 112
memory, 119
NIC, 113
power supplies, 117
processor, 125
system cooling, 117
system startup failure, 111
video, 112
wet system, 114
U
UEFI Boot Manager
entering, 47
main screen, 48
System Utilities screen, 49
UEFI Boot Manager Screen, 48
USB
front-panel connectors, 12
internal connector for memory
key, 101
USB key
troubleshooting, 120
V
video
front-panel connectors, 12
troubleshooting, 112
W
warning messages, 32
warranty, 32
wet system
troubleshooting, 114
Coaster_HOM.book Page 141 Monday, November 3, 2014 3:23 PM
142 Index
Coaster_HOM.book Page 142 Monday, November 3, 2014 3:23 PM