Table of Contents
DELL U2417H User Manual
Displayed below is the user manual for U2417H by DELL which is a product in the Computer Monitors category. This manual has pages.
Related Manuals
Model: U2417HA
Regulatory model: U2417Ht
Dell UltraSharp U2417HA
User’s Guide
NOTE: A NOTE indicates important information that helps you make better use of
your computer.
CAUTION: A CAUTION indicates potential damage to hardware or loss of data if
instructions are not followed.
WARNING: A WARNING indicates a potential for property damage, personal
injury, or death.
Copyright © 2016 Dell Inc. All rights reserved. This product is protected by U.S. and international
copyright and intellectual property laws.
Dell™ and the Dell logo are trademarks of Dell Inc. in the United States and/or other jurisdictions.
All other marks and names mentioned herein may be trademarks of their respective companies.
2016 – 01 Rev. A00
Contents
About Your Monitor ..................................... 5
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Identifying Parts and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Monitor Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Plug-and-Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
LCD Monitor Quality and Pixel Policy. . . . . . . . . . . . . . . . . . . . . . .21
Setting Up the Monitor.................................. 22
Installing the Arm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Organizing Your Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Using the Tilt, Swivel, Pivot, Vertical and Horizontal Extension . . . . . 30
Adjusting the Rotation Display Settings of Your System . . . . . . . . . . 32
Connecting Your Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Removing the Monitor Arm. . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Wall Mounting (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Operating the Monitor .................................. 38
Turning on the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Using the Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . . 38
Using the On-Screen Display (OSD) Menu . . . . . . . . . . . . . . . . . . . 41
Contents | 3
4 | Contents
Troubleshooting ....................................... 53
Self-Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Built-in Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Common Problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Product Specific Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Mobile High-Definition Link (MHL) Specific Problems. . . . . . . . . . . . 58
Appendix .............................................. 59
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
FCC Notices (U.S. only) and Other Regulatory Information . . . . . . . . 59
Contacting Dell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Setting Up Your Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Maintenance Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
About Your Monitor | 5
About Your Monitor
Package Contents
Your monitor ships with the components shown below. Make sure that you have
received all the components and contact Dell if something is missing.
NOTE: Some items may be optional and may not ship with your monitor.
Somefeatures or media may not be available in certain countries.
Monitor
Arm riser
Arm base
Allen key
Power cable (varies by country)
6 | About Your Monitor
USB 3.0 upstream cable (enables
the USB ports on the monitor)
DP cable (DP to mDP)
•Drivers and documentation media
•Quick Setup Guide
•Safety and Regulatory Information
•Factory Calibration Report
Product Features
The Dell UltraSharp U2417HA monitor has an active matrix, thinfilm transistor (TFT),
liquid crystal display (LCD), and LED backlight. The monitor features include:
• 60.47 cm (23.8-inch) active area display (Measured diagonally) 1920 x 1080
resolution, plus full-screen support for lower resolutions.
• Wide viewing angles with 99% sRGB color.
• Tilt, swivel, pivot, vertical and horizontal extension adjustment capabilities.
• Removable pedestal and Video Electronics Standards Association (VESA™) 100 mm
mounting holes for flexible mounting solutions.
• Ultra-thin bezel minimizes the bezel gap in multi-monitor usage, enabling easier
set up with an elegant viewing experience.
• Extensive digital connectivity with DP, mDP, HDMI/MHL, and USB 3.0 helps future-
proof your monitor.
• Plug and play capability if supported by your system.
• On-Screen Display (OSD) adjustments for ease of set-up and screen optimization.
• Software and documentation media includes an information file (INF), Image
color Matching File (ICM), Dell Display Manager software application and product
documentation. Dell Display Manager included (comes in the CD attached with the
monitor).
• Security lock slot.
• Asset Management Capability.
• Energy Star Compliant.
• EPEAT Gold Compliant.
• RoHS compliant.
• BFR/PVC Free monitor (excluding cables).
• Arsenic-Free glass and Mercury Free for Panel only.
• Energy Gauge shows the energy level being consumed by the monitor in real time.
• 0.5 W standby power when in the sleep mode.
• TCO Certified Displays.
8 | About Your Monitor
Back View
Label Description Use
1VESA mountiong holes (100 mm
x 100 mm-behind attached VESA
cover)
Wall mount monitor using VESA-
compatible wall mount kit (100 mm x 100
mm).
2Regulatory label Lists the regulatory approvals.
3Arm release button Release arm from monitor.
4Security lock slot Secures monitor with security cable lock
(sold separately).
5Barcode, serial number, and Service
Tag label
Refer to this label if you need to contact
Dell for technical support.
NOTE: All except APJ having service tag.
6Arm cover Remove the cover to access the cable
management compartment.
7Cable management compartment Use to organize cables by routing them
through the compartment. See Organizing
Your Cables.
Side View
USB downstream port
Port with lightning icon is for
BC 1.2
About Your Monitor | 9
Bottom View
Label Description Use
1AC power connector To connect the monitor power cable.
2HDMI/MHL connector Connect your computer with HDMI cable or MHL
devices with MHL cable (optional).
3DP connector (in) Connect your computer with DP cable.
4mDP connector (in) Connect your computer with mDP to DP cable.
5DP connector (out) DP output for MST (multi-stream transport) capable
monitor. DP 1.1 monitor can only be connected as
the last monitor in the MST chain. To enable MST,
refer to instruction on section “Connecting the
Monitor for DP MST Function”.
NOTE: Remove the rubber plug when use DP out
connector.
6Audio line-out port Connect speakers to playback audio coming
through HDMI or DP audio channels.
Only supports 2-channel audio.
NOTE: The audio line-out port does not support
headphones.
WARNING: Excessive sound pressure from
earphones or headphones can cause hearing
damage or loss.
7USB upstream port Connect the USB cable that comes with your
monitor to the computer. Once this cable is
connected, you can use the USB downstream
connectors on the monitor.
8USB downstream ports (2) Connect your USB device. You can only use this
connector after you have connected the USB cable
to the computer and USB upstream connector on
the monitor.
9Arm lock Lock the arm to the monitor using a M3 x 6 mm
screw (screw not included).
10 | About Your Monitor
Monitor Specifications
Flat Panel Specifications
Screen type Active matrix - TFT LCD
Panel type In-plane switching (IPS)
Viewable image
Diagonal 60.47 cm (23.80 inches)
Active Area
Horizontal 527.04 mm (20.75 inches)
Vertical 296.46 mm (11.67 inches)
Area 156246.28 mm2 (242.18 inches2)
Pixel pitch 0.2745 mm x 0.2745 mm
Viewing angle
Horizontal 178° (typical)
Vertical 178° (typical)
Luminance output 250 cd/m² (typical)
Contrast ratio 1000 to 1 (typical)
Faceplate coating Anti-glare treatment of the front polarizer (3H)
Backlight LED
Response Time 8 ms (typical), 6 ms (fast mode)
Color depth 16.7 million colors
Color gamut 99% sRGB
Resolution Specifications
Horizontal scan range 30 kHz to 83 kHz (DP/HDMI)
27 kHz to 70 kHz (MHL)
Vertical scan range 50 Hz to 75 Hz (DP/HDMI)
24 Hz to 60 Hz (MHL)
Maximum preset resolution 1920 x 1080 at 60 Hz
Video display capabilities
(DP & HDMI & MHL playback)
480i, 480p, 576i, 576p, 720p, 1080i, 1080p
About Your Monitor | 11
Preset Display Modes
Display Mode Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(Horizontal/
Vertical)
720 x 400 31.5 70.0 28.3 -/+
VESA, 640 x 480 31.5 60.0 25.2 -/-
VESA, 640 x 480 37.5 75.0 31.5 -/-
VESA, 800 x 600 37.9 60.3 40.0 +/+
VESA, 800 x 600 46.9 75.0 49.5 +/+
VESA, 1024 x 768 48.4 60.0 65.0 -/-
VESA, 1024 x 768 60.0 75.0 78.8 +/+
VESA, 1152 x 864 67.5 75.0 108.0 +/+
VESA, 1280 x 1024 64.0 60.0 108.0 +/+
VESA, 1280 x 1024 80.0 75.0 135.0 +/+
VESA, 1600 x 1200 75.0 60.0 162.0 +/+
VESA, 1920 x 1080 67.5 60.0 148.5 +/+
MHL Source Display Modes
Display Mode Frequency
(Hz)
640 x 480p 60
720 x 480p 60
720 x 576p 50
720 (1440) x 480i 60
720 (1440) x 576i 50
1280 x 720p 60
1280 x 720p 50
1920x1080i 60
1920x1080i 50
1920x1080p 30
1920x1080p 60
12 | About Your Monitor
MST Multi-Stream Transport (MST) Modes
MST Source Monitor Maximum number of external monitor that can be
supported
1920 x 1080/60 Hz
1920 x 1080/60 Hz 2
NOTE: Maximum external monitor resolution supported is 1920x1080 60Hz only.
Electrical Specifications
Video input signals •Digital video signal for each dierential line
Per dierential line at 100 ohm impedance
•DP/HDMI/MHL signal input support
Input voltage/ frequency/current 100-240 VAC / 50 or 60 Hz ± 3 Hz / 1.6 A
(maximum)
Inrush current 120 V: 40 A (Max.)
240 V: 80 A (Max.)
Physical Characteristics
Connector type •DP connector (include DP in and DP out)
•mDP connector
•HDMI/MHL connector
•Audio line-out
•USB 3.0 upstream port connector
•USB 3.0 downstream port connector x 4
(Port with lightning icon is for BC 1.2)
Signal cable type DP to mDP 1.8 M cable
USB 3.0 1.8 M cable
Dimensions (with arm)
Height (extended) 497.7 mm (19.59 inches)
Height (compressed) 317 mm (12.48 inches)
Depth (extended) 408.3 mm (16.07 inches)
Depth (compressed) 184.2 mm (7.25 inches)
Width 537.6 mm (21.17 inches)
Dimensions (without arm)
Height 314.3 mm (12.37 inches)
Width 537.6 mm (21.17 inches)
Depth 46.1 mm (1.81 inches)
About Your Monitor | 13
Arm dimensions
Height 441.6 mm (17.39 inches)
Width 121.6 mm (4.79 inches)
Depth 384.3 mm (15.13 inches)
Weight
Weight with packaging 8.2 kg (18.08 lb)
Weight with arm assembly and
cables 5.9 kg (13.01 lb)
Weight without arm assembly
(For wall mount or VESA
mount considerations - no
cables)
3.2 kg (7.05 lb)
Weight of arm assembly 2.3 kg (5.07 lb)
Environmental Characteristics
Temperature
Operating 0°C to 40°C (32°F to 104°F)
Non-operating –20°C to 60°C (–4°F to 140°F)
Humidity
Operating 10% to 80% (non-condensing)
Non-operating 5% to 90% (non-condensing)
Altitude
Operating 5,000 m (16,404 ft) (maximum)
Non-operating 12,192 m (40,000 ft) (maximum)
Thermal dissipation 232 BTU/hour (maximum)
64.8 BTU/hour (typical)
14 | About Your Monitor
Power Management Modes
If you have VESA’s DPM-compliant video card or software installed in your PC, the
monitor can automatically reduce its power consumption when not in use. This is
referred to as power save mode*. If the computer detects input from the keyboard,
mouse, or other input devices, the monitor automatically resumes functioning. The
following table shows the power consumption and signaling of this automatic power
saving feature.
VESA
Modes
Horizontal
Sync
Vertical
Sync
Video Power Indicator Power Consumption
Normal
operation
Active Active Active White 68 W (maximum)**
19 W (typical)
Active-off
mode
Inactive Inactive Off White
(blinking slowly)
Less than 0.5 W
Switch off - - - Off Less than 0.3 W
Energy Star Power Consumption
On Mode 16.93 W***
The OSD operates only in the normal operation mode. If you press any button in the
active-off mode, one of the following message is displayed:
*Zero power consumption in OFF mode can only be achieved by disconnecting
the AC mains cable from the monitor.
**Maximum power consumption with maximum luminance.
*** Energy consumption (On Mode) is tested at 230 Volts / 50 Hz.
This document is informational only and reflects laboratory performance. Your product
may perform differently, depending on the software, components and peripherals you
ordered and shall have no obligation to update such information. Accordingly, the
customer should not rely upon this information in making decisions about electrical
tolerances or otherwise. No warranty as to accuracy or completeness is expressed or
implied.
Activate the computer and the monitor to gain access to the OSD.
NOTE: This monitor is ENERGY STAR -compliant.
About Your Monitor | 15
Pin Assignments
DP connector (in)
Pin number 20-pin side of theconnected signal cable
1ML3(n)
2GND
3ML3(p)
4ML2(n)
5GND
6ML2(p)
7ML1(u)
8GND
9ML1(p)
10 ML0(n)
11 GND
12 ML0(p)
13 CONFIG1
14 CONFIG2
15 AUX CH (p)
16 GND
17 AUX CH (n)
18 Hot Plug Detect
19 Return
20 DP_PWR
16 | About Your Monitor
DP connector (out)
Pin number 20-pin side of theconnected signal cable
1ML0(p)
2GND
3ML0(n)
4ML1(p)
5GND
6ML1(n)
7ML2(p)
8GND
9ML2(n)
10 ML3(p)
11 GND
12 ML3(n)
13 CONFIG1
14 CONFIG2
15 AUX CH(p)
16 GND
17 AUX CH(n)
18 Hot Plug Detect
19 Return
20 DP_PWR
About Your Monitor | 17
mDP connector
Pin number 20-pin side of theconnected signal cable
1GND
2Hot Plug Detect
3ML3 (n)
4CONFIG1
5ML3 (p)
6CONFIG2
7GND
8GND
9ML2 (n)
10 ML0 (p)
11 ML2 (p)
12 ML0 (p)
13 GND
14 GND
15 ML1 (n)
16 AUX (p)
17 ML1 (p)
18 AUX (n)
19 GND
20 DP_PWR
18 | About Your Monitor
HDMI connector
Pin number 19-pin side of theconnected signal cable
1TMDS DATA 2+
2TMDS DATA 2 SHIELD
3TMDS DATA 2-
4TMDS DATA 1+
5TMDS DATA 1 SHIELD
6TMDS DATA 1-
7TMDS DATA 0+
8TMDS DATA 0 SHIELD
9TMDS DATA 0-
10 TMDS CLOCK+
11 TMDS CLOCK SHIELD
12 TMDS CLOCK-
13 CEC
14 Reserved (N.C. on device)
15 DDC CLOCK (SCL)
16 DDC DATA (SDA)
17 DDC/CEC Ground
18 +5 V POWER
19 HOT PLUG DETECT
About Your Monitor | 19
MHL connector
Pin number 19-pin side of theconnected signal cable
1N/C
2CD_SENSE
3N/C
4N/C
5TMDS_GND
6N/C
7MHL+
8MHL_Shield
9MHL-
10 N/C
11 TMDS_GND
12 N/C
13 N/C
14 N/C
15 CD_PULLUP
16 N/C
17 VBUS_CBUS_GND
18 VBUS
19 CBUS
2Shell Shield
20 | About Your Monitor
Universal Serial Bus (USB)
This section gives you information about the USB ports available on your monitor.
NOTE: Up to 2 A on USB downstream port (port with lightning icon) with BC
1.2 compliance devices; up to 0.9 A on the other 3 USB downstream ports.
Your computer has the following USB ports:
• 1 upstream - bottom
• 4 downstream - 2 at left side, 2 at bottom
Power Charging Port - the one on the left side (Port with lightning icon);
supports fast current charging capability if the device is BC 1.2 compatible.
NOTE: The monitor’s USB ports work only when the monitor is on or in the power
save mode. If you turn off the monitor and then turn it on, the attached peripherals
may take a few seconds to resume normal functionality.
Transfer speed Data rate Power consumption
SuperSpeed 5 Gbps 4.5 W (Max., each port)
Hi-Speed 480 Mbps 2.5 W (Max., each port)
Full speed 12 Mbps 2.5 W (Max., each port)
USB upstream port USB downstreamport
Pin number Signal name Pin number Signal name
1 VBUS 1 VBUS
2D- 2D-
3D+ 3D+
4GND 4GND
5StdB_SSTX- 5StdA_SSRX-
6StdB_SSTX+ 6StdA_SSRX+
7GND_DRAIN 7GND_DRAIN
8StdB_SSRX- 8StdA_SSTX-
9StdB_SSRX+ 9StdA_SSTX+
Shell Shield Shell Shield
About Your Monitor | 21
Plug-and-Play
You can install the monitor in any Plug-and-Play-compatible system. The monitor
automatically provides the computer system with its extended display identification data
(EDID) using display data channel (DDC) protocols so the computer can configure itself
and optimize the monitor settings. Most monitor installations are automatic; you can
select different settings if desired. For more information about changing the monitor
settings, see Operating the Monitor.
LCD Monitor Quality and Pixel Policy
During the LCD monitor manufacturing process, it is not uncommon for one or more
pixels to become fixed in an unchanging state which are hard to see and do not affect
the display quality or usability. For more information on LCD Monitor Pixel Policy, see
Dell support site at: http://www.dell.com/support/monitors.
22 | Setting Up the Monitor
Setting Up the Monitor
Installing the Arm
NOTE: The arm riser and arm base are detached when the monitor is shipped
from the factory.
NOTE: The arm installing instruction is applicable to the arm shipped with the
monitor. For other mounting solutions (optional), please refer to their respective set
up instructions.
Installing the Arm Base
There are a few types of table configurations which the arm base could be installed:
A. Table with open edge
B. Table with partition with gap between
C. Table with grommet hole
D. Others
A. Table with open edge
• Install the 2 screws either on top row or the
bottom row of arm base bracket depending
on the table thickness.
• Insert the clamp bracket key holes to the
screws and slide down to secure in place.
Setting Up the Monitor | 23
• Slide the arm base assembly completely
into the table.
• Tighten the thumbscrew until the clamp
disc is fully in contact with the underside of
table.
B. Table with partition with gap between
• Insert the arm base bracket through the gap
between table and partition.
24 | Setting Up the Monitor
• Install the 2 screws either on top row or the
bottom row of arm base bracket depending
on the table thickness.
• Insert the clamp bracket key holes to the
screws and slide down to secure in place.
• Tighten the thumbscrew until the clamp
disc is fully in contact with the underside of
table.
Setting Up the Monitor | 25
C. Table with grommet hole
• Insert the arm base bracket through the
grommet hole.
• Install the 2 screws either on top row or the
bottom row of arm base bracket depending
on the table thickness.
• Insert the clamp bracket key holes to the
screws and slide down to secure in place.
26 | Setting Up the Monitor
• Tighten the thumbscrew until the clamp
disc is fully in contact with the underside of
table.
D. Others
Some office partition systems have a swing-open panel for cable management. In
certain cases, the swing-open panel might cause obstruction to the arm base
installation as illustrated below.
A. Without opening the panel, the gap is too small to insert the arm base bracket.
B. The panel need to be opened first before inserting the arm base bracket into the
gap.
C. However, the height of the arm base pole obstructs the panel from closing back.
Setting Up the Monitor | 27
The recommended arm base installation steps to overcome this issue:
A. Remove the pole from the arm base by removing the center screw.
B. Open the panel and insert the arm base bracket through the gap.
C. Close the panel and install back the pole to the arm base bracket.
28 | Setting Up the Monitor
Installing the Arm Riser
• Insert the arm riser fully into the pole of the
arm base which has been installed to the
table.
• Fully tighten the set screw using the Allen
key to prevent the arm riser accidentally
detaching from the arm base.
• Place the grooves on the back of monitor
into the two tabs on the top part of the arm.
• Tilt the monitor down till the monitor snaps
into its place.
Setting Up the Monitor | 29
Organizing Your Cables
1. Remove the arm cover which is attached
with magnets to the arm riser.
2. Slide the cable bracket upwards to unlock.
3. Flip the cable bracket up until it holds still in
position.
• Thread the cables from bottom up through
the cable clips and bracket.
• The cables should exit from the arm bottom
opening and connected to the respective
connectors on the monitor.
1. Flip down the cable bracket fully.
2. Slide the cable bracket downward until it is
locked in place.
NOTE: Ensure the cables do not overlap on
top of each other.
• Attach the arm cover.
30 | Setting Up the Monitor
Using the Tilt, Swivel, Pivot, Vertical and Horizontal
Extension
NOTE: This is applicable to the arm shipped with this monitor. For other mounting
solutions please refer to their respective set up instructions.
Tilt and Vertical Extension
With arm attached to the monitor, you can tilt and lift the monitor to the most
comfortable viewing position.
Setting Up the Monitor | 31
Swivel and Horizontal Extension
With arm attached to the monitor, you can swivel the monitor and pan the arm to a
optimum monitor viewing distance or just simply to compact the monitor to have a
clear desk.
Pivoting
Before you pivot the monitor, your monitor should be fully lifted vertically and fully tilted
up to avoid hitting the bottom edge of the monitor.
NOTE: To use the Display Rotation function (Landscape versus Portrait view) with
your Dell computer, you require an updated graphics driver that is not included
with this monitor. To download the graphics driver, go to www.dell.com/support
and see the Download section for Video Drivers for latest driver updates.
NOTE: When in the Portrait View Mode, you may experience performance
degradation in graphic-intensive applications (3D Gaming and etc.).
32 | Setting Up the Monitor
Adjusting the Rotation Display Settings of Your System
After you have rotated your monitor, you need to complete the procedure below to
adjust the Rotation Display Settings of your System.
NOTE: If you are using the monitor with a non-Dell computer, you need to go the
graphics driver website or your computer manufacturer website for information on
rotating the ’contents’ on your display.
To adjust the Rotation Display Settings:
1 Right-click on the desktop and click Properties.
2 Select the Settings tab and click Advanced.
3 If you have an ATI graphics card, select the Rotation tab and set the preferred
rotation.
4 If you have an nVidia graphics card, click the nVidia tab, in the left-hand column
select NVRotate, and then select the preferred rotation.
5 If you have an Intel® graphics card, select the Intel graphics tab, click Graphic
Properties, select the Rotation tab, and then set the preferred rotation.
NOTE: If you do not see the rotation option or it is not working correctly, go to
www.dell.com/support and download the latest driver for your graphics card.
Setting Up the Monitor | 33
Connecting Your Monitor
WARNING: Before you begin any of the procedures in this section, follow the
Safety Instructions.
To connect your monitor to the computer:
1 Turn o your computer.
2 Connect the HDMI/DP-mDP/USB cable from your monitor to
thecomputer. (Vertically extend and tilt the monitor completely to rotate it for
cable connection. See Pivoting.)
3 Switch on your monitor.
4 Select the correct input source at Monitor OSD Menu and turn on your
computer.
NOTE: U2417HA default setting is DP 1.2. DP 1.1 Graphic card may not display
normally. Please refer to “product specific problems – No image when using DP
connection to the PC” to change default setting.
Connecting the HDMI cable(Optional)
Connecting the DP (or mDP) cable
NOTE: Default is DP port. Select input source on monitor to switch to mDP.
34 | Setting Up the Monitor
Connecting the monitor for DP Multi-Stream Transport (MST)
function
NOTE: Supports the DP MST feature. To make use of this feature, your PC
Graphics Card must be certified to DP1.2 with MST option.
NOTE: Remove the rubber plug when using the DP out connector.
Connecting the USB cable
Setting Up the Monitor | 35
Using the Mobile-High Definition Link (MHL)
NOTE: This monitor is MHL ready.
NOTE: To use the MHL function, use only MHL-certified cable and source devices
that support MHL output.
NOTE: Some MHL source devices may take more than a few seconds or longer to
output an image, depending on MHL source devices.
NOTE: When the connected MHL source device enters standby mode, the monitor
displays a black screen or the message below, depending on MHL source device’s
output.
To enable MHL connection, please perform the below steps:
1 Plug the power cable on your monitor into a AC outlet.
2 Connect the (micro) USB port on your MHL source device to HDMI/MHL port
on the monitor with a MHL certified cable (see Bottom View for details).
3 Turn on the monitor and the MHL source device.
4 Select input source on monitor to HDMI/MHL by using OSD menu (see Using
the On-Screen Display (OSD) Menu for details).
5 If the monitor does not display an image, see Mobile High-Definition Link
(MHL) Specific Problems.
36 | Setting Up the Monitor
Removing the Monitor Arm
CAUTION: Place monitor of a flat, clean, and soft surface to avoid scratching
the display panel.
NOTE: The arm installing instruction is applicable to the arm shipped with the
monitor. For other mounting solutions (optional), please refer to their respective
set up instructions.
To remove the arm:
1. Press and hold the arm-release button.
2. Lift the monitor up and away from the
arm.
• Turn the screw anticlockwise with an Allen
key.
• Remove the arm riser from the arm base
by pulling it in the direction of the arrow
as shown in the figure.
• Turn the fixed screw at the bottom of the
arm base to separate it.
Setting Up the Monitor | 37
Wall Mounting (Optional)
NOTE: Use M4 x 10 mm screws to connect the monitor to the wall-mounting kit.
Refer to the instructions that come with the VESA-compatible wall mounting kit.
1 Place the monitor on a soft cloth or cushion on a stable, flat table.
2 Remove the arm.
3 Use a Phillips crosshead screwdriver to remove the four screws securing the
plastic cover.
4 Attach the mounting bracket from the wall mounting kit to the monitor.
5 Mount the monitor on the wall by following the instructions that comes with the
wall mounting kit.
NOTE: For use only with UL or CSA or GS-listed wall mount bracket with minimum
weight/load bearing capacity of 3.2 kg (7.05 lb).
38 | Operating the Monitor
Operating the Monitor
Turning on the Monitor
Press the button to turn on the monitor.
Using the Front Panel Controls
Use the control buttons on the front of the monitor to adjust the characteristics of the
image being displayed. As you use these buttons to adjust the controls, an OSD shows
the numeric values of the characteristics as they change.
Operating the Monitor | 39
The following table describes the front panel buttons:
Front-Panel Button Description
1
Shortcut key:
Preset Modes
Use this button to choose from a list of preset
colormodes.
2
Shortcut key:
Input Source
Use this button to choose from a list of Input Source.
3
Menu
Use this menu button to launch the on-screen
display (OSD) and select the OSD menu.
See Accessing the Menu System.
4
Exit
Use this button to go back to the main menu or exit
the OSD main menu.
5
Power (with power light
indicator)
Use the Power button to turn the monitor On and
Off.
The white LED indicates the monitor is On and fully
functional.
A glowing white LED indicates DPMS Power Save
Mode.
40 | Operating the Monitor
Front-Panel Button
Use the buttons on the front of the monitor to adjust the image settings.
Front Panel Button Description
1
Up Down
Use the Up (increase) and Down (decrease) keys to adjust
items in the OSD menu.
2
OK
Use the OK button to confirm your selection.
3
Back
Use the Back button to go back to the previous menu.
Operating the Monitor | 41
Using the On-Screen Display (OSD) Menu
Accessing the Menu System
NOTE: Any changes you make using the OSD menu are automatically saved if
youmove to another OSD menu, exit the OSD menu, or wait for the OSD menu
todisappear.
1 Press the button to launch the OSD menu and display the main menu.
2 Press the and buttons to move between options. As you move from one
icon to another, the option name is highlighted.
3 Press the or or button once to activate the highlighted option.
4 Press the and buttons to select the desired parameter.
5 Press to enter the slide bar and then use the or button, according to the
indicators on the menu, to make your changes.
6 Select the to return to previous menu or to accept and return to previous
menu.
42 | Operating the Monitor
Icon Menu and
Submenus
Description
Brightness/
Contrast
Use this menu to activate Brightness/Contrast adjustment.
Brightness Brightness adjusts the luminance of the backlight
(minimum 0; maximum 100).
Press the button to increase brightness.
Press the button to decrease brightness.
NOTE: Manual adjustment of Brightness is disabled when
Dynamic Contrast is switched on.
Contrast Adjust the Brightness first, and then adjust Contrast only if
further adjustment is necessary.
Press the button to increase contrast and press the
button to decrease contrast (between 0 and 100).
Contrast adjusts the difference between darkness and
lightness on the monitor.
Input Source Use the Input Source menu to select between different video
inputs that are be connected to your monitor.
Operating the Monitor | 43
Icon Menu and
Submenus
Description
DP Select DP input when you are using the DP (DisplayPort)
connector.
Use to select the DP input source.
mDP Select mDP input when you are using the
mDP (mini DisplayPort) connector.
Use to select the mDP input source.
HDMI/MHL Select the HDMI/MHL input when you are using the HDMI
connector.
Use to select the HDMI/MHL input source.
Auto Select Use to select Auto Select, the monitor scans for available
input sources.
Reset Input
Source
Resets your monitor’s Input Source settings to the factory
defaults.
Color Use the Color menu to adjust the color setting mode.
44 | Operating the Monitor
Icon Menu and
Submenus
Description
Preset Modes When you select Preset Modes, you can choose Standard,
Multimedia, Movie, Game, Paper, Color Temp., sRGB or
Custom Color from the list.
•Standard: Default color settings. This is the default preset
mode.
•Multimedia: Ideal for multimedia applications.
•Movie: Ideal for movies.
•Game: Ideal for most gaming applications.
•Paper: Loads brightness and sharpness settings ideal for
viewing text. Blend the text background to simulate paper
media without aecting color images.
•Color Temp.: The screen appears warmer with a red/yellow
tint with slider set at 5,000K or cooler with blue tint with
slider set at 10,000K.
•sRGB: Emulates 99% sRGB.
•Custom Color: Allows you to manually adjust the color
settings. Press the and buttons to adjust the Red,
Green, and Blue values and create your own preset color
mode.
Operating the Monitor | 45
Icon Menu and
Submenus
Description
Input Color
Format
Allows you to set the video input mode to:
•RGB: Select this option if your monitor is connected to a
computer (or DVD player) using the HDMI, DP-mDP cable or
MHL devices using the MHL cable.
•YPbPr: Select this option if your DVD player supports only
YPbPr output.
Gamma Allows you to set the Gamma to PC or MAC.
Hue Use or to adjust the hue from 0 to 100.
NOTE: Hue adjustment is available only for Movie and Game
mode.
Saturation Use or to adjust the saturation from 0 to 100.
NOTE: Saturation adjustment is available only for Movie and
Game mode.
Reset Color Resets your monitor’s color settings to the factory defaults.
46 | Operating the Monitor
Icon Menu and
Submenus
Description
Display Use the Display menu to adjust image.
Aspect Ratio Adjust the image ratio to Wide 16:9, 4:3, or 5:4.
Monitor
Sleep
Sleep After Timeout: Monitor goes into sleep after timeout.
Never: Monitor never goes into sleep.
Sharpness Makes the image look sharper or softer.
Use or to adjust the sharpness from ‘0’ to ‘100’.
Dynamic
Contrast
Allows you to increase the level of contrast to provide sharper
and more detailed image quality.
Push the button to select the Dynamic Contrast “On”
or “Off”.
NOTE: For Game and Movie preset mode only.
NOTE: Dynamic Contrast provides higher contrast if you
select Game or Movie preset mode.
Response
Time
Allows you to set the Response Time to Normal or Fast.
MST DP Multi Stream Transport, Set to ON enables MST(DP out),
Set to OFF disables MST function.
Reset Display Restores the display settings to factory defaults.
Operating the Monitor | 47
Icon Menu and
Submenus
Description
Energy
Power
Button LED
Allows you to set the state of the power light to save energy.
USB Allows you to enable or disable USB function during monitor
standby mode.
NOTE: USB ON/OFF under standby mode is only available
when the USB upstream cable is unplugged. This option will
be greyed out when the USB upstream cable plugs in.
Reset Energy Select this option to restore default Energy settings.
Menu Select this option to adjust the settings of the OSD, such as,
the languages of the OSD, the amount of time the menu
remains on screen, and so on.
48 | Operating the Monitor
Icon Menu and
Submenus
Description
Language Set the OSD display to one of eight languages.
(English, Spanish, French, German, Brazilian Portuguese,
Russian, Simplified Chinese, or Japanese).
Rotation Rotates the OSD by 0/90/180/270 degrees.
You can adjust the menu according to your display rotation.
Transparency Select this option to change the menu transparency by using
and (min. 0 / max. 100).
Timer OSD Hold Time: Sets the length of time the OSD remains
active after you press a button.
Use the and buttons to adjust the slider in 1-second
increments, from 5 to 60 seconds.
Lock Controls user access to adjustments. When Lock is selected,
no user adjustments are allowed. All buttons are locked.
NOTE:
Lock function – Either soft lock (through OSD menu) or hard
lock (Press and hold the exit button 6 sec)
Unlock function – Only hard unlock (Press and hold the exit
button 6 sec)
Reset Menu Restore the menu settings to factory defaults.
Personalize Select from Preset Modes, Brightness/Contrast, Input Source,
Aspect Ratio, Rotation set as shortcut key.
Reset
Persona-
lization
Restores shortcut keys to factory defaults.
Operating the Monitor | 49
Icon Menu and
Submenus
Description
Other
Select this option to adjust the OSD settings, suchas the
DDC/CI, LCD conditioning, and so on.
DDC/CI DDC/CI (Display Data Channel/Command Interface) allows
you to adjust the monitor settings using software on your
computer.
Select Disable to turn off this feature.
Enable this feature for best user experience and optimum
performance of your monitor.
50 | Operating the Monitor
Icon Menu and
Submenus
Description
LCD
Conditioning
Helps reduce minor cases of image retention. Depending on
the degree of image retention, the program may take some
time to run. Select Enable to start the process.
Reset Others Restores other settings, such as DDC/CI, to factorydefaults.
Factory Reset Restores all OSD settings to the factory defaults.
NOTE: This monitor has a built-in feature to automatically calibrate the brightness
to compensate for LED aging.
Operating the Monitor | 51
OSD Warning Messages
When the Dynamic Contrast feature is enabled (in these preset modes: Game or Movie),
manual brightness adjustment is disabled.
When the monitor does not support a particular resolution mode, you can see the
following message:
This means that the monitor cannot synchronize with the signal that it is receiving from
the computer. See Monitor Specifications for the Horizontal and Vertical frequency
ranges addressable by this monitor. Recommended mode is 1920 x 1080.
You can see the following message before the DDC/CI function is disabled:
When the monitor enters the Power Save mode, the following message appears:
52 | Operating the Monitor
Activate the computer and wake up the monitor to gain access to the OSD.
If you press any button other than the power button, the following messages will appear
depending on the selected input:
If either DP, mDP, HDMI/MHL input is selected and the corresponding cable is not
connected, a floating dialog box as shown below appears.
or
or
See Troubleshooting for more information.
Troubleshooting | 53
Troubleshooting
WARNING: Before you begin any of the procedures in this section, follow the
Safety Instructions.
Self-Test
Your monitor provides a self-test feature that allows you to check whether your monitor
is functioning properly. If your monitor and computer are properly connected but the
monitor screen remains dark, run the monitor self-test by performing the following
steps:
1 Turn o both your computer and the monitor.
2 Unplug the video cable from the back of the computer. To ensure proper Self-Test
operation, remove all digital and the analog cables from the back of computer.
3 Turn on the monitor.
The floating dialog box should appear on-screen (against a black background), if the
monitor cannot sense a video signal and is working correctly. While in self-test mode,
the power LED remains white. Also, depending upon the selected input, one of the
dialogs shown below will continuously scroll through the screen.
or
or
54 | Troubleshooting
4 This box also appears during normal system operation, if the video cable becomes
disconnected or damaged.
5 Turn o your monitor and reconnect the video cable; then turn on both your
computer and the monitor.
If your monitor screen remains blank after you use the previous procedure, check your
video controller and computer, because your monitor is functioning properly.
Troubleshooting | 55
Built-in Diagnostics
Your monitor has a built-in diagnostic tool that helps you determine if the screen
abnormality you are experiencing is an inherent problem with your monitor, or with your
computer and video card.
NOTE: You can run the built-in diagnostics only when the video cable is unplugged
and the monitor is in self-test mode.
To run the built-in diagnostics:
1 Make sure that the screen is clean (no dust particles on the surface of the screen).
2 Unplug the video cable(s) from the back of the computer or monitor. The monitor
then goes into the self-test mode.
3 Press and hold Button 1 and Button 4 on the front panel simultaneously for 2
seconds. A gray screen appears.
4 Carefully inspect the screen for abnormalities.
5 Press Button 4 on the front panel again. The color of the screen changes to red.
6 Inspect the display for any abnormalities.
7 Repeat steps 5 and 6 to inspect the display in green, blue, black, white, and text
screens.
The test is complete when the text screen appears. To exit, press Button 4 again.
If you do not detect any screen abnormalities upon using the built-in diagnostic tool,
the monitor is functioning properly. Check the video card and computer.
56 | Troubleshooting
Common Problems
The following table contains general information about common monitor problems you
might encounter and the possible solutions:
Common
Symptoms
What You
Experience
Possible Solutions
No Video/Power
LED off
No picture •Ensure that the video cable connecting the
monitor and the computer is properly connected
and secure.
•Verify that the power outlet is functioning
properly using any other electrical equipment.
•Ensure that the power button is depressed fully.
•Ensure that the correct input source is selected in
the Input Source menu.
No Video/Power
LED on
No picture or no
brightness
•Increase brightness & contrast controls via OSD.
•Perform monitor self-test feature check.
•Check for bent or broken pins in the video cable
connector.
•Run the built-in diagnostics.
•Ensure that the correct input source is selected in
the Input Source menu.
Missing Pixels LCD screen has
spots
•Cyclepoweron-off.
•Pixelthatispermanentlyoffisanaturaldefect
that canoccur in LCD technology.
•FormoreinformationonDellMonitorQuality
and Pixel Policy, see Dell Support site at:
http://www.dell.com/support/monitors.
Stuck-on Pixels LCD screen has
bright spots
•CyclepowerOn-Off.
•Pixelthatispermanentlyoffisanaturaldefect
that canoccur in LCD technology.
•FormoreinformationonDellMonitorQuality
and PixelPolicy, see Dell Support site at:
http://www.dell.com/support/monitors.
Brightness
Problems
Picture too dim
or too bright
•Reset the monitor to factory settings.
•Adjust brightness & contrast controls via OSD.
Safety Related
Issues
Visible signs of
smoke or sparks
•Do not perform any troubleshooting steps.
•Contact Dell immediately.
Intermittent
Problems
Monitor
malfunctions on
& off
•Ensure that the video cable connecting the
monitor to the computer is connected properly
and is secure.
•Resetthemonitortofactorysettings.
•Perform monitor self-test feature check to
determine if the intermittent problem occurs in
self-test mode.
Troubleshooting | 57
Common
Symptoms
What You
Experience
Possible Solutions
Missing Color Picture missing
color
•Perform monitor self-test.
•Ensure that the video cable connecting the
monitor to the computer is connected properly
and is secure.
•Check for bent or broken pins in the video cable
connector.
Wrong Color Picture color
not good
•Change the settings of the Preset Modes in the
Color menu OSD depending on the application.
•Adjust R/G/B value under Custom. Color in Color
menu OSD.
•Change the Input Color Format to PC RGB or
YPbPr in the Color menu OSD.
•Run the built-in diagnostics.
Image retention
from a static
image left on
the monitor for
a long period of
time
Faint shadow
from the static
image displayed
appears on the
screen
•Use the Power Management feature to turn o
the monitor at all times when not in use (for more
information, see Power Management Modes).
•Alternatively, use a dynamically changing
screensaver.
Product Specific Problems
Specific
Symptoms
What You
Experience
Possible Solutions
Screen image is
too small
Image is
centered on
screen, but does
not fill entire
viewing area
•Check the Aspect Ratio setting in the Display
menu OSD.
•Reset the monitor to factory settings.
Cannot adjust
the monitor
with the buttons
on the front
panel
OSD does not
appear on the
screen
•Turn o the monitor, unplug the monitor power
cable, plug it back, and then turn on the monitor.
•Check whether the OSD menu is locked. If yes,
press and hold the button beside the power
button for 6 seconds to unlock (for more
information, see Lock).
No Input Signal
when user
controls are
pressed
No picture,
the LED light is
white
•Check the signal source. Ensure the computer
is not in the power saving mode by moving the
mouse or pressing any key on the keyboard.
•Check whether the signal cable is plugged in
properly. Re-plug the signal cable if necessary.
•Reset the computer or video player.
The picture
does not fill the
entire screen
The picture
cannot fill the
height or width
of the screen
•Due to dierent video formats (aspect ratio) of
DVDs, the monitor may display in full screen.
•Run the built-in diagnostics.
58 | Troubleshooting
Specific
Symptoms
What You
Experience
Possible Solutions
No image
when using DP
connection to
the PC
Black screen •Verify which DP standard (DP 1.1a or DP 1.2) is
your Graphics Card certified to. Download and
install the latest graphics card driver.
•Some DP 1.1a graphics card cannot support
DP 1.2 monitors. Go to OSD menu, under Input
Source selection, press and hold DP select
key for 8 sec to change the monitor setting from
DP 1.2 to DP 1.1a.
Mobile High-Definition Link (MHL) Specific Problems
Specific
Symptoms
What You
Experience
Possible Solutions
MHL interface is
not working
Cannot see
MHL device
image shown
on the monitor
•Ensure your MHL cable and MHL device are MHL
certified.
•Check your MHL device is turned on.
•Check your MHL device is not in standby mode.
•Check physical MHL cable connection is
corresponding to input source selected on OSD
Menu: HDMI/MHL.
•Wait for 30 seconds after connecting MHL cable
as some MHL devices require longer recovery
time.
Appendix | 59
Appendix
Safety Instructions
For displays with glossy bezels the user should consider the placement of the display as
the bezel may cause disturbing reflections from surrounding light and bright surfaces.
WARNING: Use of controls, adjustments, or procedures other than those
specified in this documentation may result in exposure to shock, electrical
hazards, and/or mechanical hazards.
For information on safety instructions, see the Safety, Environmental, and Regulatory
Information (SERI).
FCC Notices (U.S. only) and Other Regulatory
Information
For FCC notices and other regulatory information, see the regulatory compliance
website located at www.dell.com/regulatory_compliance.
Contacting Dell
NOTE: If you do not have an active Internet connection, you can find contact
information on your purchase invoice, packing slip, bill, or Dell product catalog.
Dell provides several online and telephone-based support and service options.
Availability varies by country and product, and some services may not be available in
your area.
To get online Monitor support content:
See www.dell.com/support/monitors.
To contact Dell for sales, technical support, or customer service issues:
1 Go to www.dell.com/support.
2 Verify your country or region in the Choose A Country/Region drop-down menu
at the top-left corner of the page.
3 Click Contact Us next to the country dropdown.
4 Select the appropriate service or support link based on your need.
5 Choose the method of contacting Dell that is convenient for you.
60 | Appendix
Setting Up Your Monitor
Setting Display Resolution to 1920x1080 (maximum)
For best performance, set the display resolution to 1920x1080 pixels by performing the
following steps:
In Windows Vista, Windows 7, Windows 8 or Windows 8.1:
1 For Windows 8 or Windows 8.1 only, select the Desktop tile to switch to classic
desktop.
2 Right-click on the desktop and click Screen Resolution.
3 Click the Dropdown list of the Screen Resolution and select 1920x1080.
4 Click OK.
In Windows 10:
1 Right-click on the desktop and click Display Settings.
2 Click Advanced display settings.
3 Click the dropdown list of Resolution and select 1920 x 1080.
4 Click Apply.
If you do not see the recommended resolution as an option, you may need to update
your graphics driver. Please choose the scenario below that best describes the
computer system you are using, and follow the given steps.
Dell computer
1 Go to www.dell.com/support, enter your service tag, and download the latest
driver for your graphics card.
2 After installing the drivers for your graphics adapter, attempt to set the resolution to
1920x1080 again.
NOTE: If you are unable to set the resolution to 1920x1080, please contact Dell
to inquire about a graphics adapter that supports these resolutions.
Appendix | 61
Non-Dell computer
In Windows Vista, Windows 7, Windows 8 or Windows 8.1:
1 For Windows 8 or Windows 8.1 only, select the Desktop tile to switch
to classic desktop.
2 Right-click on the desktop and click Personalization.
3 Click Change Display Settings.
4 Click Advanced Settings.
5 Identify your graphics controller supplier from the description at the top of the
window (e.g. NVIDIA, ATI, Intel etc.).
6 Refer to the graphic card provider website for updated driver (for example,
http://www.ATI.com or http://www.NVIDIA.com).
7 After installing the drivers for your graphics adapter, attempt to set the resolution
to 1920 x 1080 again.
In Windows 10:
1 Right-click on the desktop and click Display Settings.
2 Click Advanced display settings.
3 Click Display adapter properties.
4 Identify your graphics controller supplier from the description at the top of the
window (e.g. NVIDIA, ATI, Intel etc.).
5 Refer to the graphic card provider website for updated driver (for example,
http://www.ATI.com or http://www.NVIDIA.com).
6 After installing the drivers for your graphics adapter, attempt to set the resolution
to 1920x1080 again.
NOTE: If you are unable to set the recommended resolution, please contact the
manufacturer of your computer or consider purchasing a graphics adapter that
supports the video resolution.
62 | Appendix
Maintenance Guidelines
Cleaning Your Monitor
WARNING: Before cleaning the monitor, unplug the monitor power cable from
the electrical outlet.
CAUTION: Read and follow the Safety Instructions before cleaning the monitor.
For best practices, follow these instructions in the list below while unpacking, cleaning,
or handling your monitor:
• To clean your anti-static screen, lightly dampen a soft, clean cloth with water. If
possible, use a special screen-cleaning tissue or solution suitable for the anti-static
coating. Do not use benzene, thinner, ammonia, abrasive cleaners, or compressed
air.
• Use a lightly-dampened, soft cloth to clean the monitor. Avoid using detergent of
any kind as some detergents leave a milky film on the monitor.
• If you notice white powder when you unpack your monitor, wipe it off with a cloth.
• Handle your monitor with care as a darker-colored monitor may get scratched and
show white scuff marks more than a lighter- colored monitor.
• To help maintain the best image quality on your monitor, use a dynamically
changing screen saver and turn off your monitor when not in use.