Duracell Jump-Starter 750 with Air Compressor User Manual
Displayed below is the user manual for Jump-Starter 750 with Air Compressor by Duracell which is a product in the Vehicle Power Stations category. This manual has pages.
Related Manuals
IMPORTANT
If you keep the jump-starter in storage, the battery will discharge over time. Remember to
recharge the battery every three months to keep the jump-starter operational.
7. Maintenance
Routine maintenance is required to keep your Duracell® jump-starter operating properly.
Occasionally clean the exterior of the unit with a damp cloth to remove the accumulated dust
and dirt.
WARNING: SHOCK HAZARD
Disconnect all sources of AC power and DC power before performing any type of
maintenance.
► Battery maintenance
All rechargeable batteries gradually discharge when left standing, and you need to recharge
them periodically to maintain maximum battery capacity. The internal AC battery charger
supplied with the jump-starter is designed to regulate the charging process, ensuring that
the battery is always fully charged but never overcharged. To ensure safe recharging and
maximum battery life, recharge the jump-starter only with the supplied charger.
CAUTION
Due to inherent self-discharge, lead acid batteries must be charged at least every 3
months, especially in a warm environment. Leaving a battery in a discharged state, or not
recharging every 3 months, may result in permanent battery damage and poor jump-
starting performance.
CAUTION
Do not attempt to recharge the jump-starter battery if it is frozen. Gradually warm the
frozen battery to 32 °F (0 °C) before recharging.
8. Using the air compressor
IMPORTANT: Please read these general usage-related warnings and
cautions thoroughly before using the Jump-starter’s air compressor.
Fire Safety
The compressor is designed for short term operation only. Operating the compressor over an
extended period of time will cause the compressor unit to overheat which could lead to re.
The powerpack cannot be used to inate large capacity inatables such as oat tubes, large
air mattresses, and inatable boats. These types of products require extended inating times
that may damage the compressor.
Always allow the compressor to cool down for 10 minutes after each 10 minutes of continuous
operation.
Personal Safety
Never leave the compressor unattended while in operation. Keep out of reach of children.
The compressor is capable of inating to 160 PSI. Do not exceed the recommended pressure
of either the compressor or the object being inated. If either recommended pressure is
exceeded, an explosion
may result.
If the pressure gauge on the compressor indicates more than twice the recommended
pressure for the object you are inating, and you have only started to inate the object, the
valve connector is incorrectly connected to the valve stem. This may damage the Jump-starter.
Remove and reattach the valve connector to the valve stem.
Portable Emergency
Jump-starter+Compressor
1. Features
1: Pressure gauge
2: Air compressor on/o
3: Fuel gauge button and
USB on/o switch
turns
on the fuel gauge indicator.
Turns on power to the USB
charge port.
4: LED fuel gauge/
battery level indicator
shows battery fuel level.
5: USB charge port
Supplies up to 2.1 Amps of
charging power for your USB
devices.
6:12V DC power socket
powers 12V DC devices and
appliances.
7: Jump-starter ON/OFF
switch
8: Negative jump starting
clamp
(see Section 6).
9: Emergency light
provides bright LED
illumination in dark locations
.
10: Positive jump
starting clamp
(see
Section 6).
11: Storage compartment
for compressor hose,
accessories and charger
cord.
12: AC battery charger
recharges the jump-starter’s
internal battery from a
standard AC wall outlet.
13
:
AC power cord
14: Compressor
accessories
2. Important Safety Information
Misusing or incorrectly connecting the Duracell® Jump-starter may damage the equipment or
create hazardous conditions for users.
WARNING: ELECTRICAL SHOCK HAZARD
The jump-starting clamps may spark if touched together. Always keep the clamps in their
storage holsters when they are not being used.
3. Charging/Recharging the Jump-starter
► Charging before rst use
IMPORTANT
Prior to using the jump-starter for the rst time, ensure that the battery of the jump-starter
is fully charged. If the battery has been fully discharged, charging/recharging with the AC
battery charger may take up to 12 hours.
► Charging / recharging with the internal charger
Recharging with the internal charger is a true “plug-in-and-forget” charging method. We
recommend leaving the AC battery charger connected when the jump-starter is not in use.
1. Disconnect any USB and 12V DC appliances from the DC power outlets.
2. Remove the AC cord from the storage compartment under the unit.
3. Insert the AC cord end into the AC cord input port, then plug AC cord into a standard AC
wall outlet.
4. The fuel gauge LEDs sequence during charging and remain solid on when fully charged.
5. Recharging time should be approximately 12 hours if the jump-starter battery is fully
discharged.
IMPORTANT
If you keep the jump-starter in storage, the battery will discharge over time. Remember to
recharge the battery every three months to keep the jump-starter operational.
4. Checking the Jump-starter’s Battery Level
To check the battery’s charge level, press the Fuel Gauge button. The LED lights will illuminate
and display the current level of available battery power. Press again to turn off (or will turn off
automatically after one minute).
When all four lights are lit, this indicates that your Jump-starter is fully charged. It is
recommended to maintain a full charge on the Jump-starter at all times for optimal jump
starting and device charging.
Note: Battery Fuel Gauge status is only accurate when the jump-starter has been
disconnected from all appliances and all charging sources for 15 minutes.
5. Using The Jump-starter’s Light / Power Ports
► Using the built-in light
The Duracell® Jump-starter has a built-in emergency light to provide a safe, bright work light on
the roadside and in other outdoor environments.
1. Push the “HOLD FOR LIGHT” button for 2 seconds to turn on the LED light.
2. Position the jump-starter so that the light illuminates your work area.
3. When done, push the “HOLD FOR LIGHT” button for 2 seconds to turn the LED light off.
► Using the USB port
The USB port provides up to 2.1 Amps of power to charge cell phones, smartphones, tablets
and other devices.
To charge USB devices:
1. Connect your USB device (smartphone, tablet etc.) to the USB port using the USB cable
supplied with your device.
2. Push the “USB ON/OFF” button.
3. Charging will start and up to 2.1 Amps of current can be supplied by the port. The USB
device controls the amount of current supplied.
4. The USB port never “pushes” more than required by the devices.
5. Push the “USB ON/OFF” button again when done to turn the USB port off.
Note: USB output will turn off after one minute if not plugged into a USB device.
► Using the 12V DC power socket
The jump-starter can operate 12V DC appliances that draw 11A or less.
CAUTION: EQUIPMENT DAMAGE
The DC power outlet does not automatically switch off when the internal battery is
discharged. Check the battery status periodically to prevent total battery discharge.
To operate a 12V DC appliance:
1. Open the protective cover on the jump-starter’s DC power socket.
2. Plug the 12V DC appliance into the DC power outlet on the side of the unit, and turn the
12V DC appliance on (if required).
3. Fully recharge the jump-starter as soon as possible after each use.
4. As the DC power socket is internally wired directly to the jump-starter’s battery, extended
operation of a 12V DC appliance may result in excessive battery discharge. See
“Caution: Equipment Damage” above.
6. Jump-Starting A Vehicle’s Engine
You can use the Duracell® jump-starter with the supplied jump-start cables to jump-start a
vehicle or boat engine that has a 12V starting battery.
WARNING: FIRE HAZARD
Never allow jump-start cables’ red and black clamps to touch each other or another
common metal conductor. This could cause damage to the unit and/or create a sparking/
explosion hazard.
WARNING: FIRE HAZARD
Jump-start cable clamps’ connection to the vehicle’s battery terminals must be positive
to positive (red clamp to battery “+”) and negative to engine block. A reverse polarity
connection (positive to negative) may cause damage to the unit and/or create a sparking/
explosion hazard.
WARNING: FIRE HAZARD
Do not crank the engine for more than 4 seconds. The jump-start feature is designed for
short term operation only. Operating the jump-start feature for more than 4 seconds may
cause damage to the unit. Allow the jump-starter to cool down for at least 30 seconds after
each jump-start.
► To jump-start a vehicle engine:
1. Turn OFF the vehicle or boat ignition and all accessories.
2. Engage the park or emergency brake and place the transmission in park for an
automatic or neutral for a manual.
3. If jump-starting a boat engine, purge the engine compartment and bilge of all fumes.
4. Position the jump-starter on a at, stable surface near the battery and away from all
moving parts of the engine.
5. Make sure the red the Jump-starter switch is in the OFF position then connect the red
positive (+) clamp of the cables to the positive (+) terminal of the engine battery. The
battery’s positive terminal is usually larger in diameter than the negative terminal. In
most vehicles, the battery’s positive terminal has a red wire connected to it. (Refer to
your vehicle’s owner manual).
6. Connect the black negative (–) clamp of the cables to the negative battery terminal,
engine block, cylinder head, or other stationary heavy metal part of the motor.
7. Correct polarity must be established before proceeding. Re-check your connections
before starting your engine. If the clamps are reversed, an alarm will sound and
“CLAMPS REVERSED” LED illuminate. Disconnect the jump-start clamps from the
vehicle’s battery and redo steps 5 and 6 in this procedure.
8. Before starting the engine, make sure the jump-starter and the cables are clear of belts
and fans.
9. Turn the jump-starter switch to the ON position and turn over the engine for 4 seconds or
until it starts, whichever is rst.
10. Turn the jump-starter switch to the OFF position and remove the red positive (+) clamp
and then the black negative (–) clamp from the vehicle.
11. Store the jump-start clamps in the appropriate holder on each side of the jump-starter.
Red POSITIVE (“+”)
clamp
connects
to
positive
battery
terminal
Black NEGATIVE (“
-
”) clamp
connects to the negative battery
terminal OR
metal part of car
(block, cylinder, etc)
Inating tires (car, motorcycle, bicycle)
1. Unwind the air compressor hose from the side compartment of the unit.
2. Place the valve connector securely on the tire valve stem, turn the valve connector
on the hose to securely attach it to the tire valve. If necessary, use a supplied nozzle
adapter.
3. Press the AIR COMPRESSOR switch to turn the compressor on, and inate your tire to
its recommended pressure.
4. Switch the compressor off after appropriate pressure is reached.
5. Unscrew the valve connector and remove the valve connector from the
valve stem.
Inating tires using the nozzle adapters
6. Locate proper nozzle adapter stored with the compressor hose.
7. Insert nozzle adapter into the valve receptacle of the item.
8. Follow item 1-3 above
9. Turn the compressor off before removing nozzle adapter from valve stem.
10. Remove nozzle adapter from valve connector and return it to the storage compartment.
9. Troubleshooting
Below are some common problems that can occur with the Jump-starter’s compressor. If
you cannot solve your problem, contact your dealer or Duracell Customer Service at (800)
300-1857.
Problem: The compressor runs, but won’t inate.
Possible Cause Solution
The valve connector may not be securely
placed on the valve stem.
Make sure the valve connector is
securely placed and screwed onto the
valve stem.
The item being inated may have a leak. Make sure the item being inated
doesn’t have a leak. Check the
compressor hose for any breaks or
leaks.
Problem: The compressor runs slowly.
Possible Cause Solution
The compressor may have overheated from
excessive use.
Turn o the compressor and let it cool
down.
Battery voltage is too low. Check the condition of the internal
battery. The battery may need to be
recharged or replaced.
10. User reference: Tire ination
The information in the table below is for reference only. For precise pressure specications,
refer to the information supplied with the item to be inated.
Type of tire Typical pressure
specications (PSI)
Automotive tires
520-13 26
A-78-14 26
E78-14 30
H-78-14 24
HR-78-15 28
Bicycle tires
27 x 1 ¼ 85
20 x 1 ½ 40
Other Inatables
Football 13
Basketball 9
Volleyball 5
Lawn tractor tire 22
11. Specications
Electrical specications
12V DC section 750 Jump-starter
+ Compressor
900 Jump-starter
+ Compressor
Internal battery type Sealed/non-spillable, AGM
(Absorbed Glass Mat) lead-acid
Internal battery voltage (nominal) 12V DC
Internal battery capacity (minimum) 9Ah 12Ah
DC power socket (maximum continuous
load)
11A with automatic reset
Battery charging controller
system
750 Jump-starter
+ Compressor
900 Jump-starter
+ Compressor
AC input voltage 100 - 240V AC BC
Nominal output voltage 12V DC
Empty load power < 0.35W
Safety certications / efciency
certications
ETL
Physical specications
750 Jump-starter
+ Compresspor
900 Jump-starter
+ Compresspor
Length 13.1" (33.5 cm)
Width 5.0" (12.9 cm)
Height 9.8" (25.0cm)
Weight 10.1 lbs. (4.58 kg) 13.5 lbs. (6.1 kg)
12. General Warnings and Cautions
IMPORTANT: Please read these general usage-related warnings and cautions thoroughly
before using this jump-starter.
WARNING: Shock hazard. Keep away from children.
Do not insert foreign objects into the DC power socket, the USB port, or the ventilation
holes. Do not expose this product to water, rain, snow, or spray. Do not open the unit.
There are no user serviceable parts inside the unit.
CAUTION
Do not operate the jump-starter or compressor in temperatures under 0°C (32°F) or over
40°C (104°F).
WARNING: Explosion hazard
Do not use this product where there are ammable fumes or gases, such as in the bilge of
a gasoline-powered boat, or near propane tanks. Use caution when using this product in an
enclosure containing automotive-type lead-acid batteries. These batteries, unlike the sealed
AGM battery in the Jump-starter, vent explosive hydrogen gas which can be ignited by
sparks from electrical connections. When working on electrical equipment, always ensure
someone is nearby to help you in an emergency.
WARNING: Proper application
Do not use the appliance for any application except that for which it is intended.
WARNING: Medical equipment
This product is NOT tested, designed nor intended to be used with life support systems or
any other medical devices.
WARNING: Proper application
Do not use the appliance for any application except that for which it is intended.
WARNING
This product contains chemical(s) known to the State of California to cause cancer, birth
defects, or other reproductive harm.
13. Recycling
Battery-Biz is committed to environmental responsibility and recommends that electronic
devices be disposed of properly. Please contact your local city ofces for information on
recycling and disposal programs for e-waste.
For instructions on how to recycle this product visit
http://www.call2recycle.org.
14. Contacting Customer Support
If you experience any problems or have any questions regarding your DURACELL® product,
free technical support is available.
Be prepared to provide the following information:
- Name, address and telephone number
- Name of the DURACELL® product
- Make and model of your device
- Symptoms of the problem(s) and what led to them
Technical Support is available by telephone:
U.S. and Canada (800) 300-1857
Outside of the US/Canada: (805) 437-7765
Written inquires should be directed to:
Battery-Biz Inc.
DURACELL® Product Inquiry
1380 Flynn Road, Camarillo, CA 93012, USA
15. Warranty and Return Information
Two Year Limited Warranty
The DURACELL® product carries a limited warranty against defects in material and
workmanship under normal use and service for two years from the original date of purchase.
The manufacturer or distributor, at its option, shall repair or replace the defective unit covered
by this warranty. Please retain the dated sales receipt as evidence of the date of purchase
as it will be required for any warranty service. In order to keep the warranty in effect, the
product must have been handled and used as described in the instructions accompanying
this warranty. This warranty does not cover any damage due to accident, misuse, abuse or
negligence.
Disclaimer Of Warranty
The limited warranty described herein is your sole remedy. To the extent permitted by law,
the manufacturer and distributor disclaim all other implied or express warranties including all
warranties of merchantability and/or tness for any particular purpose.
© 2017 Duracell. Bethel, CT 06801. DURACELL® is a registered trademark of Duracell U.S. Operations, Inc., used under
license. All rights reserved. All logos and trademarks are used for identication purposes only and may be trademarks or
registered trademarks of their respective holders.
UM-DRJS20C/30C Rev 20170111
Limitation Of Liability
Except to the extent of repairing or replacing this product as expressly stated in the limited
warranty described herein, the manufacturer and distributor shall not be liable for any
damages, whether direct, indirect, incidental, special,consequential, exemplary, or otherwise,
including lost revenues, lost prots, loss of use of software, loss or recovery of data, rental
of replacement equipment, downtime, damage to property, and third-party claims, arising
out of any theory of recovery, including statutory, contract or tort. Not withstanding the
term of any limited or implied warranty, or in the event that any limited warranty fails of its
essential purpose, in no event will the manufacturer’s and distributors entire liability exceed
the purchase price of this product. Some states and provinces do not allow the exclusion or
limitation of incidental or consequential damages so the above limitations or exclusions may
not apply to you. This limited warranty gives you specic legal rights. You may have other
rights which vary from state to state and province to province.
AIR
COMPRESSOR
HOLD FOR LIGHT
USB ON/OFF
BATTERY LEVEL
BATTERY LEVEL
CLAMPS
REVERSED