Equip 650811 User Manual
Displayed below is the user manual for 650811 by Equip which is a product in the Computer Desks category. This manual has pages.
Related Manuals
ERGO Electric Sit-Stand Desk
Frame with Desktop, Grey/Black
INSTALLATION MANUAL
650811(Grey)
650812(Black)
What tools are needed to
assemble the desk frame?
What important specifications
should know before installation?
Checklist and Installation
Please check all of the components shown in the component checklist. If any of the components are missing or damaged,
contact your point of purchase for a replacement.
D (x2)
Side Bracket
F (x1)
Lifting Column
H (x2)
Foot
I (x1)
AC Adapter
K (x1)
Power Cord
L (x1)
Controller
The picture of the controller is for
your reference only. Actual product
may vary.
E (x1)
Lifting Column
G (x1)
Sync Rod
S-A (x4)
M6x12
Hex Head Screw
S-E (x10)
ST4.8x16
Phillips Head Screw
S-G (x1)
5mm
Allen Wrench
S-F (x3)
Cable Clip
A (x2)
Desktop
B (x1)
Crossbar
C (x3)
Connecting Plate
S-H (x1)
4mm
Allen Wrench
S-C (x8)
M6x30
Hex Head Screw
S-B (x4)
M6x8
Hex Head Screw
S-D (x23)
ST4.2x13
Phillips Head Screw
J (x4)
Wooden Dowel Pins
Power Input
(100~240V)
Operation Temperature
(-5°C~+40°C)
Weight Capacity
70kg (154lbs)
Allen Wrench
(Included)
Drill Phillips Screwdriver
Bubble Level
3. Attaching the Feet
B
E
F
1. Attaching the Crossbar
• Attach the Crossbar to the Lifting Columns and
using 4 M6x8 Screws as shown in the illustration.
B
S-B
E
F
• Turn over the desk frame with the help of another
person.
• Place the Lifting Column / upside down on
the floor.
• Attaching the Foot to the Lifting Column using
4 M6x30 Screws .
• Repeat the same process to attach the other foot.
H
E F
S-C
2. Attaching the Side Brackets
• Attach each Side Bracket to the Lifting Column
using 2 M6x12 Screws .
• Repeat the same process to attach the other
side bracket.
D
S-A
S-H
D
S-A
S-G
S-C
H
E F
/
CAUTION: At least two people are required
when turning over the desk, or serious bodily
injuries might occur.
S-B
S-G
4. Assembling the Desktop
Shipping Blanket
A
J
C
S-D
• Carefully place the dissassembled Desktop upside down on the floor as shown.
• Assemble the desktop with 4 Wooden Dowel Pins and 3 Connecting Plates using
18 ST4.2x13 Screws .
A
JC
S-D
Note: Please make sure the desktop keep facing down while installation.
5. Attaching the Sync Rod
• Place the assembled desk frame to the backside of the desktop.
• Align the screw holes on the desktop with mounting holes found on the crossbar
and side brackets.
G
• Turn the knob as shown in the illustration to loosen and adjust the Sync Rod .
• Insert both ends of Sync Rod into holes found on the desk frame
as shown in the illustration.
• Re-tighten the knob.
G
6. Attaching the Desk Frame to the Desktop
• Attaching the assembled desk frame to the desktop through the mounting holes
found on the Side Brackets and Crossbar as shown in the illustration using
8 ST4.8x16 Screws .
S-E
Drill
S-E
9. Cable Management
S-D
S-F
Drill
• Run the cables through the Cable Clips and attach the cable clips to the desktop with 3 ST4.2x13 Screws
to ensure clean and neat surface.
S-F S-D
Bubble Level
CAUTION: At least two people are required when turning over
the desk, otherwise serious bodily injuries might occur.
10. Adjusting the Desk
• Turn over the desk with the help of another person.
• There are two adjustable foot pads under each foot. If the floor isn't even,
simply turn the pad to adjust the level to make the desk stable.
Tip: Use a bubble level (not included) to check if the desktop is even.
• Connect the desk to power. Long press the up and down buttons to adjust the height.
Instructions of Safety and Warnings:
Disposal: The product with this mark indicates that this product shouldn't be disposed with other household
wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled
waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your
used device, please use the local recycle service or contact your point of purchase to withdrawn the product.
Electrical Safety Instructions:
The product is powered by electricity. In order to avoid burns, fire and electric shock, please read the
instructions carefully.
CAUTION
Don't disassemble or replace components
while the power is still connected.
Never operate the system with a damaged cord
or plug. Please contact your point of purchase to
replace the damaged parts.
Don't clean the product with water
while the power is still connected.
Never operate the system if it's in moist
environment or its electrical components
have contact with liquids.
Don't operate the system if the control box
makes noise or odor.
Alterations of the given power unit and
control box aren't allowed.
Other Safety Instructions:
·Remove any obstacles from the area around the desk during assembly and subsequent use.
·Organize all cords and wires to prevent any possible tripping or accidents from occurring.
·Never attempt to modify or change the desk frame or components that operate the desk.
·Don't add anything to the adjustable junctions of the desk frame.
·The desk is rated for Indoor Use Only.
• Overlooking any part of the instructions, warnings and additional information marked with the "Note" and " "
may result in serious damage to the system or its components.
• Children should never be allowed to operate or touch the product without direct supervision of an adult. Users
should prevent children from being near or around the desk during operation.
• Any failure to comply with the safety and installation instructions in this manual may cause serious bodily injury.
• Disabilities and/or lack of experience and knowledge should be prevented from using the product unless under
supervision or assisted during use and operation.
• Never sit on or exceed the rated weight of the desk.
CAUTION