Table of Contents
- FUJITSU LIFEBOOK E544 / FUJITSU LIFEBOOK E554
- Contents
- Fujitsu Contact Information
- Notational conventions
- Ports and operation controls
- Important notes
- First-time setup of your device
- Working with the notebook
- Status indicators
- Switching the notebook on
- Switching the notebook off
- Keyboard
- Application keys (ECO and Wireless)
- Touchpad and touchpad buttons
- LCD screen
- Webcam
- Rechargeable battery
- Modular bay devices
- Optical drive
- Removing and replacing the removable dust filter
- Using the energy saving functions
- Memory cards
- Speaker and microphones
- Wireless LAN/Bluetooth components
- Ethernet and LAN
- Your port replicator
- Security functions
- Connecting external devices
- Removing and installing components during servicing
- Settings in BIOS Setup Utility
- Starting the BIOS Setup Utility
- BIOS Setup Utility operation
- Exiting BIOS Setup Utility
- Exit Saving Changes - save changes and exit BIOS Setup Utility
- Exit Discarding Changes - Reject changes and exit BIOS Setup Utility
- Load Setup Defaults – load default values
- Discard Changes - Discard Changes without exiting BIOS Setup Utility
- Save Changes - save changes without exiting the BIOS Setup Utility
- Save changes and power off
- Troubleshooting and tips
- Help if problems occur
- Recovering your Factory Image
- The notebook's date or time is incorrect
- When certain characters are entered on the keyboard, only numerals are written
- The notebook’s LCD screen remains blank
- The LCD screen of the notebook is difficult to read
- The external monitor remains blank
- The external monitor is blank or the image is unstable
- The notebook does not start after switching it on
- The notebook stops working
- The printer does not print
- The wireless connection to a network does not work
- Acoustic warning
- Smart Card reader is not recognized
- Smart Card PIN forgotten
- Smart Card lost
- Error messages on the screen
- Technical data
- Manufacturer’s notes
- Appendix
- Index
Fujitsu E544 User Manual
Displayed below is the user manual for E544 by Fujitsu which is a product in the Notebooks category. This manual has pages.
Related Manuals
System
Operating Manual
FUJITSU LIFEBOOK E544
FUJITSU LIFEBOOK E554
Contact address in North America
FUJITSU AMERICA INC.
1250 East Arques Avenue, Sunnyvale,
CA 94085-3470, U.S.A.
Telephone: 800 831 3183 or 408 746 6000
"http://solutions.us.fujitsu.com"
"http://solutions.us.fujitsu.com/contact"
Have a question? Email us at: "AskFujitsu@us.fujitsu.com"
Copyright
©2015 Fujitsu America, Inc. All rights
reserved B5FK-4391-02ENZ0-00
FUJITSU LIFEBOOK E544
FUJITSU LIFEBOOK E554
Operating Manual
Fujitsu Contact Information 7
Notational conventions 8
Ports and operation controls 9
Important notes 13
First-time setup of your device 17
Working with the notebook 20
Security functions 48
Connecting external devices 54
Removing and installing components
during servicing 61
Settings in BIOS Setup Utility 69
Troubleshooting and tips 71
Technical data 78
Manufacturer’s notes 81
Appendix 87
Index 103
Copyright and Trademark Information
Fujitsu America, Incorporated has made every effort to ensure the accuracy and completeness
of this document; however, as ongoing development efforts are continually improving the
capabilities of our products, we cannot guarantee the accuracy of the contents of this
document. We disclaim liability for errors, omissions, or future changes.
Fujitsu, the Fujitsu logo and LIFEBOOK are registered trademarks of Fujitsu Limited
or its subsidiaries in the United States and other countries.
Intel and Intel Core are trademarks or registered trademarks of Intel Corporation or
its subsidiaries in the United States and other countries.
Microsoft and Windows are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
The ExpressCard word mark and logo are owned by the Personal Computer
Memory Card International Association (PCMCIA) and any use of such marks by
Fujitsu America, Incorporated is under license.
Google is a trademark or registered trademark of Google Incorporated.
Bluetooth is a trademark of Bluetooth SIG, Inc., USA.
OmniPass is a trademark of Softex, Inc.
Roxio is a trademark of Roxio, a division of Sonic Solutions.
PowerDirector, PowerDVD, YouCam, and MakeDisc are trademarks of CyberLink Corp.
Adobe, Acrobat, and Adobe Reader are either a registered trademarks or trademarks of
Adobe Systems Incorporated in the United States and/or other countries.
Made under license from DTS Licensing Limited. DTS and the symbol are registered trademarks and
& DTS Boost is a trademark of DTS, Inc. Product contains software. © DTS, Inc. All rights reserved.
The DVD player found in some models of the LIFEBOOK notebook incorporates copyright
protection technology that is protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation and other rights users. Use
of this copyright protection technology must be authorized by Macrovision Corporation, and
is intended for home and other limited viewing uses only unless authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
All other trademarks specified here are the property of their respective owners.
Contents
Contents
FujitsuContactInformation ............................................................ 7
Notationalconventions ................................................................ 8
Portsandoperationcontrols ........................................................... 9
Importantnotes ........................................................................ 13
Safety instructions ...................................................................... 13
Additional safety notes for devices with wireless components . . ............................. 14
Energy saving .......................................................................... 14
Energy saving under Windows ....................................................... 14
Traveling with your notebook . . ........................................................... 14
Beforeyoutravel ................................................................... 15
Transporting the notebook ........................................................... 16
Cleaning the notebook .................................................................. 16
First-timesetupofyourdevice ......................................................... 17
Unpacking and checking the device . . . ................................................... 17
Choose a location . ...................................................................... 18
Connecting the AC adapter . . . ........................................................... 18
Switching on the device for the firsttime .................................................. 19
Installing Bonus Apps . . . . . ........................................................... 19
Working with thenotebook ............................................................ 20
Status indicators ........................................................................ 20
Switching the notebook on . . . . ........................................................... 22
Switching the notebook off . . . . ........................................................... 22
Keyboard ............................................................................... 23
Virtual number keys ................................................................. 25
Separate number keypad ............................................................ 26
Key combinations ................................................................... 26
Country and keyboard settings ....................................................... 28
Application keys(ECO and Wireless) ..................................................... 28
Touchpad and touchpadbuttons .......................................................... 29
Moving thepointer .................................................................. 29
Selectingan item .................................................................... 29
Executing commands . . . . . ........................................................... 29
Draggingitems ...................................................................... 30
LCD screen ............................................................................ 30
Webcam ............................................................................... 31
Rechargeable battery ................................................................... 32
Charging,caringforandmaintainingthebattery ....................................... 32
Removingandinstallingthebattery ................................................... 32
Modularbay devices .................................................................... 35
Removing a modular bay device . . . ................................................... 35
Installing a modular bay device ....................................................... 36
Opticaldrive ............................................................................ 36
Handling opticaldisks ............................................................... 36
CD/DVDindicator ................................................................... 37
Insertingorremovinganoptical disk .................................................. 37
Manualremoval(emergencyremoval) ................................................ 38
Removing and replacing the removable dust filter .......................................... 38
Fujitsu 3
Contents
Usingtheenergy savingfunctions ........................................................ 40
Memory cards .......................................................................... 41
Supportedformats .................................................................. 41
Insertingthememorycard ........................................................... 41
Removing the memorycard .......................................................... 41
Speaker and microphones . . . ............................................................ 42
Wireless LAN/Bluetooth components . . . . ................................................. 42
Switching the wireless components on and off ......................................... 42
Furtherinformation on WLANandBluetooth ........................................... 42
Ethernetand LAN ....................................................................... 43
Yourportreplicator ...................................................................... 44
Portson the portreplicator ........................................................... 44
Connecting the notebook to the port replicator . . . . . . .................................. 45
Connecting the AC adapter to the port replicator . . . . .................................. 46
Switching on the notebook via the port replicator . . . . . .................................. 46
Disconnecting the notebook from the port replicator . .................................. 47
Securityfunctions ..................................................................... 48
Configuring the fingerprint sensor ........................................................ 48
UsingtheSecurityLock ................................................................. 49
Configuring passwordprotectionin BIOS Setup Utility ...................................... 49
Protecting BIOS Setup Utility (supervisor password and user password) . . ............... 50
Password protection for booting the operating system .................................. 51
Password protection forthehard disk ................................................. 51
Trusted Platform Module - TPM (device dependent) . . . . . . .................................. 52
EnablingTPM ....................................................................... 52
DisablingTPM ...................................................................... 52
Smart Card reader . . . . . . ................................................................ 53
InsertingtheSmartCard ............................................................. 53
Connectingexternaldevices ........................................................... 54
Connecting an external monitor . . ........................................................ 55
Connecting external devices to the serial port (optional) . . .................................. 56
Port settings ........................................................................ 56
Device drivers ...................................................................... 56
Connecting USB devices ................................................................ 57
USBport withcharging function (AnytimeUSB charge) ................................. 58
Connecting an external SATA hard drive (eSATA) (port replicator only) ................... 59
Safe removal ofeSATA andUSBdevices ............................................. 59
Connecting external audio devices . . . . . . ................................................. 60
Microphone port/Line In . . ............................................................ 60
Headphones port . . . . ................................................................ 60
Removing and installing components during servicing . . . .............................. 61
Notes on installing and removing boards and components .................................. 61
Preparing to remove components ........................................................ 62
Removing and installing memory expansion . . ............................................. 62
Removing the cover ................................................................. 63
Removing a memory module ......................................................... 63
Installingamemorymodule .......................................................... 64
Attachingthecover .................................................................. 64
Removing and installing the harddisk .................................................... 65
Removing the cover ................................................................. 65
Removing the harddisk .............................................................. 66
4Fujitsu
Contents
Installingahard disk ................................................................. 67
Attaching thecover .................................................................. 68
Finishing component removal . ........................................................... 68
Settings in BIOS Setup Utility . . . ....................................................... 69
StartingtheBIOSSetupUtility ........................................................... 69
BIOS SetupUtility operation ............................................................. 69
ExitingBIOS Setup Utility ................................................................ 70
Exit Saving Changes - save changes and exit BIOS Setup Utility . . ..................... 70
Exit Discarding Changes - Reject changes and exit BIOS Setup Utility . . . . . .............. 70
Load Setup Defaults – load default values . ............................................ 70
Discard Changes - Discard Changes without exiting BIOS Setup Utility . . . . .............. 70
Save Changes - save changes without exiting the BIOS Setup Utility . . . . . . .............. 70
Save changes and power off ........................................................ 70
Troubleshootingandtips .............................................................. 71
Help ifproblemsoccur ................................................................... 71
Recovering yourFactoryImage .......................................................... 71
The notebook’s date or time is incorrect ................................................... 72
Whencertain charactersareentered onthekeyboard,only numeralsare written ............. 72
The notebook’s LCD screen remains blank . . . . ............................................ 72
The LCD screen of the notebook is difficulttoread ......................................... 72
Theexternalmonitorremainsblank ...................................................... 73
Theexternalmonitorisblank or the image isunstable ..................................... 73
The notebook does not start after switching it on . . . ........................................ 74
The notebook stops working . . ........................................................... 74
The printer does not print . . . . . ........................................................... 74
The wireless connection to a network does not work . . . .................................... 75
Acousticwarning ........................................................................ 75
Smart Card reader is not recognized . . . ................................................... 75
SmartCard PIN forgotten ................................................................ 75
SmartCard lost ......................................................................... 75
Errormessagesonthescreen ........................................................... 76
Technicaldata ......................................................................... 78
LIFEBOOK ............................................................................. 78
WLAN specifications .................................................................... 79
Rechargeablebattery ................................................................... 80
AC adapter . . . .......................................................................... 80
Manufacturer’snotes .................................................................. 81
Disposal and recycling .................................................................. 81
Recyclingyourbattery ............................................................... 81
DOC(IndustryCANADA)Notices ........................................................ 81
UL Notice ........................................................................... 82
ENERGYSTARCompliance ............................................................. 83
Declarationsofconformity ............................................................... 83
FCCandICRegulatoryInformation ...................................................... 83
Regulatory Notes and Statements . ................................................... 84
Appendix .............................................................................. 87
Before Using the Optional Wireless LAN . . . . . . ............................................ 87
WirelessLANDevicesCoveredbythisDocument ...................................... 87
Characteristics oftheWLAN Device .................................................. 87
Fujitsu 5
Contents
Wireless LAN Modes Using this Device . . ............................................. 87
Deactivating/Disconnecting theWLAN Device ......................................... 90
Configuring the WirelessLAN ............................................................ 90
Configuring the WLAN Using Windows . . . ............................................. 90
Connection to the network . . . ........................................................ 90
TroubleshootingtheWLAN ........................................................... 91
UsingtheBluetooth Device .............................................................. 93
Image Backup and Recovery Procedures ................................................. 93
Creatinga Backupof BootableDiskandRecovery Image .............................. 94
RECOVERYOURSYSTEM WHENTHEHARDDRIVEIS STILL ACCESSIBLE ............. 95
UsingtheRecovery and UtilityTools .................................................. 95
Restore the Recovery Image from Hidden Partition . . . .................................. 97
RECOVERYOURSYSTEM WHENTHEHARDDRIVEIS NOT BOOTABLE ................ 98
RestoretheRecovery ImageforFullHardDrive ....................................... 98
Recovering Your Recovery Image Using Recovery and Utility (for new hard drive or
non-bootableharddrive) ............................................................. 99
InstallingtheSoftware after theRecovery Imageis Restored ............................ 100
Index .................................................................................. 103
6Fujitsu
Fujitsu Contact Information
Fujitsu Contact Information
Service and Support
You can contact Fujitsu Service and Support in the following ways:
• Toll free number: 1-800-8Fujitsu (1-800-838-5487)
• Website: "http://solutions.us.fujitsu.com/www/content/support/contact/index.php"
Before you place the call, have the following information ready so that the customer
support representative can provide you with the fastest possible solution:
• Product name
• Product configuration number
• Product serial number
• Purchase date
• Conditions under which the problem occurred
• Any error messages that have occurred
• Type of device connected, if any
Fujitsu Shopping Online
Please go to "http://www.shopfujitsu.com/store/ ".
Maintaining Latest Configuration
To ensure that you always have the most current driver updates related to your system, occasionally
access the Fujitsu Software Download Manager (FSDM) utility. The FSDM utility is available from
the Fujitsu Support site. FSDM will allow you to view a list of the most current drivers, utilities
and applications to determine whether you have the latest versions. If you have a Windows 7
or or Windows 8/8.1 operating system, you will need to go to the Support Site to download the
FSDM Utility: "http://support.fujitsupc.com/CS/Portal/support.do?srch=DOWNLOADS".
Limited Warranty
Your LIFEBOOK notebook is backed by a Fujitsu International Limited Warranty. Check the service
kit that came with your notebook for the Limited Warranty period and terms and conditions.
Fujitsu 7
Notational conventions
Notational conventions
Pay particular attention to text marked with this symbol. Failure to observe
this warning will endanger your life, will damage the device or lead to loss
of data. The warranty will be invalidated if the device becomes defective
through failure to observe these warnings.
Indicates important information which is required to use the device properly.
►indicates an activity that must be performed
indicates a result
This style indicates data entered using the keyboard in a program dialogue or at
the command line, e.g. your password (Name123) or a command used to
start a program (start.exe)
This style indicates information that is displayed on the screen by a program, e.g.:
Installation is complete.
This style indicates
• terms and texts used in a software interface, e.g.: Click on Save.
• names of programsorfiles, e.g. Windows or setup.exe.
"This style" indicates
• Cross-references to another section, e.g. "Safety information"
• cross-references to an external source, e.g. a web address: For more
information, go to "http://solutions.us.fujitsu.com/"
• names of CDs, DVDs and titles or designations of other materials, e.g.:
"CD/DVD Drivers & Utilities" or "Safety/Regulations" manual
Key indicates a key on the keyboard, e.g: F10
This styleindicates terms and text that are emphasized or highlighted, e.g.: Do not
switch off the device
8Fujitsu
Ports and operation controls
Ports and operation controls
This chapter presents the individual hardware components of your device. It gives
an overview of the indicators and ports of the device. Please familiarize yourself with
these items before you start to work with the device.
Front
LIFEBOOK E544:
9
1
3
1
6
5
7
8
10
6
2
5
4
1 = Microphone (optional)
2 = Webcam (optional)
3 = Webcam LED (optional)
4 = Touchpad
5 = Speaker
6 = Status indicators
7 = Application keys (ECO and Wireless)
8 = ON/OFF button
9 = Fingerprint sensor (optional)
10 = Touchpad buttons
Fujitsu 9
Ports and operation controls
LIFEBOOK E554:
4
9
1
3
1
5
6
5
7
8
10
6
2
1 = Microphone (optional)
2 = Webcam (optional)
3 = Webcam LED (optional)
4 = Touchpad
5 = Speaker
6 = Status indicators
7 = Application keys (ECO and Wireless)
8 = ON/OFF button
9 = Fingerprint sensor (optional)
10 = Touchpad buttons
Left side
123 4 5 6 7 8
1 = DC input connector (DC IN)
2 = Ventilation slots
3 = LAN port
4 = External monitor port (VGA)
5 = Display Port
6 = USB port 3.0 with charging function
(Anytime USB charge)
7 = Smart Card reader (optional)
8 = Memory card slot
10 Fujitsu
Ports and operation controls
Right side
1 2 345 6
1 = Headphones port
2 = Microphone port
3=USBport3.0
4 = USB port 3.0
5 = Modular bay with optional optical drive
6 = Security Lock device
Rear
1
1 = Optional serial interface
(LIFEBOOK E554 only)
Fujitsu 11
Ports and operation controls
Bottom
2
24
5
3
1
6
7
1 = Modular bay release latch
2 = Battery lock slider switch
3 = Port replicator port
4 = Battery compartment
5 = Removable dust filter
6 = Memory upgrade compartment
7 = Hard drive access compartment
12 Fujitsu
Important notes
Important notes
ImportantnotesNotes
This chapter contains essential safety information which must be followed
when working with your notebook. Other notes also provide useful information
which will help you with your notebook.
Safety instructions
SafetyinformationInform ation,
Please observe the following safety information.
Please pay special attention to the sections in the manual marked
with the symbol on the left.
When connecting and disconnecting cables, observe the relevant
notes in this operating manual.
Read the information on the ambient conditions in the "Technical data", Page 78
chapter and the "First-time setup of your device", Page 17 chapter before preparing
your notebook for use and switching it on for the first time.
When cleaning the device, please observe the relevant notes in the
section "Cleaning the notebook", Page 16.
Pay attention to the additional safety notes for devices with radio components
provided in the "Safety/Regulations" manual.
Please refer to the notes in the chapter "Removing and installing
components during servicing", Page 61.
When handling this device, you will come into contact with lead, a chemical which in
California is held to be a possible cause of birth defects and other damage to fertility.
Wash your hands after using the device.
This notebook complies with the relevant safety regulations for data processing equipment.
If you have any questions about setting up your notebook in the intended environment,
please contact your sales outlet or our Hotline/Service Desk.
Fujitsu 13
Important notes
Additional safety notes for devices with
wireless components
wirelesscomponentsWirelessLANBluetooth,Safetynotes
If a wireless component (wireless LAN, Bluetooth) is incorporated in your notebook, you must
be sure to observe the following safety notes when using your notebook:
• Switch off the wireless components when you are in an aircraft or driving in a car.
• Switch off the wireless components when you are in a hospital, an operating
room or near a medical electronics system. The transmitted radio waves
can impair the operation of medical devices.
• Switch off the wireless components, when you let the device get near flammable
gases or into hazardous environments (e.g. gas station, paintshops), as the
transmitted radio waves can cause an explosion or a fire.
For further information on how to switch the wireless components on and off, refer
to chapter "Switching the wireless components on and off", Page 42.
Energy saving
NotesEnergyPowersaving
Switch the notebook off when it is not in use. Switch off any connected external devices when
they are not in use. If you use the energy saving functions, the notebook uses less power. You
will then be able to work for longer before having to recharge the battery.
The energy efficiency is increased and environmental pollution is reduced.
You save money and help protect the environment.
Energy saving under Windows
►Make use of the available energy saving functions as described in chapter
"Using the energy saving functions", Page 40.
Traveling with your notebook
Mobileoperation
NotesTr ansp ort
Notebook
Please observe the points listed below when traveling with your notebook.
14 Fujitsu
Important notes
Before you travel
►Back up important data stored on your hard disk.
NotebookTraveling,notebo ok
►Switch off the radio component for data security reasons. With data traffic via a wireless
connection, it is also possible for unauthorized third parties to receive data.
Information on activating data encryption is provided in the documentation
for your radio component.
►If you wish to use your notebook during a flight, check with the flight attendants if its use is safe.
When traveling in other countries
►If you are traveling abroad, check that the AC adapter can be operated with the local AC
voltage. If this is not the case, obtain the appropriate AC adapter for your notebook.
Do not use any other converter!
►Check whether the local AC voltage and the AC cable are compatible. If this is not
the case, buy an AC cable that suits the local conditions.
►Enquire with the corresponding government office of the country you will be traveling to,
whether you may use your notebook with its integrated radio component there.
►Take the necessary travel adapters with you when traveling abroad. Check the following
table to see which travel adapters you will need, or ask your travel organizer.
Power connection Travel destination
United States, Canada, Mexico, parts of Latin
America, Japan, Korea, Philippines, Taiwan
Russia and the Commonwealth of Independent
States (CIS), much of Europe, parts of Latin
America, the Middle East, parts of Africa, Hong
Kong, India, much of south-east Asia
United Kingdom, Ireland, Malaya, Singapore,
parts of Africa
China, Australia, New Zealand
Fujitsu 15
Important notes
Transporting the notebook
Protect the notebook from severe shocks and extreme temperatures
(e.g. direct sunlight in a car).
►If your device has an optical drive, remove all optical disks from the drives (e.g. CD, DVD).
TransportNotebook
►Switch the notebook off.
►Unplug the AC plug of the AC adapter and all external devices from the power outlets.
►Disconnect the AC adapter cable and the data cables for all external devices.
►Close the LCD screen.
►To protect against damaging jolts and bumps, use a notebook carrying
case to transport your notebook.
Cleaning the notebook
Do not clean any interior parts yourself; leave this job to a service technician.
Only use cleaning products designed for computers. Normal household
cleaners and polishes can damage the markings on the keyboard and the
device, the paintwork or the notebook itself.
Ensure that no liquid enters the notebook.
The LCD screen very sensitive to scratches. Only clean the display
surface with a very soft, slightly damp cloth.
►Switch the notebook off.
CleaningInstru ctions
NotebookKeyboardTouchpadLCDscreenCrystalView screen
►To prevent the device being switched on unintentionally, remove the AC plug
of the AC adapter from the power outlet and remove the battery (see chapter
"Removing and installing the battery", Page 32).
Thecasings
urfaces may be cleaned with a dry cloth.
If particularly dirty, use a damp cloth which has been dipped in water containing
some mild domestic detergent and then well wrung out.
To clean the keyboard and the touchpad if present, you can use disinfectant wipes.
Ensure that no moisture reaches the inside of the device!
16 Fujitsu
First-time setup of your device
First-time setup of your device
First- timese tupGettingstarted
Please read the chapter "Important notes", Page 13.
If your device is equipped with a Windows operating system, the necessary
hardware drivers and supplied software are already pre-installed.
Before switching it on for the first time, connect the device to the AC voltage using
the AC adapter, see "Connecting the AC adapter", Page 18. The AC adapter must
remain connected during the whole of the installation process.
A system test is performed when your device is first switched on. Various messages
can appear. The display may remain dark for a short time or may flicker.
Please follow the instructions on the screen.
NEVER switch off your device during the first-time setup process.
On delivery, the battery can be found in the battery compartment or in the accessories kit.
The battery must be charged if you want to operate your device using the battery.
When used on the move, the built-in battery provides the device with the necessary power. You
can increase the operating time by using the available energy saving functions.
For instructions on how to connect external devices (e.g. mouse, printer) to your
device, please refer to the operating manual for your device.
Unpacking and checking the device
If you find that damage has occurred during transport, please notify
your local sales outlet immediately!
►Unpack all the individual parts.
PackagingTran sport
►Check your device for any visible damage which may have occurred during transportation.
You may need to reuse the packaging in the future, for example if
you need to ship your device.
Fujitsu 17
First-time setup of your device
Choose a location
ChoosealocationSetupAC adapter
Choose a suitable location for the device before setting it up. In doing
so, please follow these instructions:
• Never place the device or the AC adapter on a heat-sensitive surface.
The surface could be damaged as a result.
• Never place the device on a soft surface (e.g. carpeting, upholstered furniture,
bed). This can block the air vents and cause overheating and damage.
• The underside of the device heats up during normal operation. Prolonged contact
with the skin can become unpleasant or even result in burns.
• Place the device on a stable, flat, non-slippery surface. Please note that the
rubber feet of the device may mark certain types of delicate surfaces.
• Keep other objects at least 100 mm / 3.97 inches away from the device
and its AC adapter to ensure adequate ventilation.
• Never cover the ventilation openings of the device.
• Do not expose the device to extreme environmental conditions.
Protect the device against dust, humidity and heat.
Connecting the AC adapter
MakingreadytouseACadapter
Observe the safety notes in the enclosed "Safety/Regulations" manual.
The supplied AC cable conforms to the requirements of the country in which
you purchased your device. Make sure that the AC cable is approved for
use in the country in which you intend to use it.
3
1
2
►Connect the AC cable (1) to the AC adapter.
►Plug the AC cable (2) into a power outlet.
►Connect the AC adapter cable (3) to the
DC jack (DC IN) of the device.
18 Fujitsu
First-time setup of your device
Switching on the device for the first time
Switchingonforthefirstt ime
To make it easier to use your device for the first time, the operating system
is pre-installed on the hard disk.
►Switch your device on.
►During the installation process, follow the on-screen instructions.
You can find information and help on the Windows operating system functions
on the Internet at "http://windows.microsoft.com".
Installing Bonus Apps
BonusApps
After you have started your system the first time, you will see a Bonus Apps icon on your desktop.
►Click on the icon to see which additional applications are available for you to install.
Applications that are already installed appear in grey, those that are
available for installation appear in blue.
►Select the applications you wish to install by selecting the checkbox adjacent to your selection.
or
►Click Select All if you would like to install all available applications.
►To confirm your selection, click Install.
Note that in some cases (depending upon which application was selected for
installation) after installation completes, the system will prompt you to reboot.
There are also cases in which if multiple applications are selected to install
but one of them needs a reboot, the system will reboot and continue
installing the rest of the selected applications.
Fujitsu 19
Working with the notebook
Working with the notebook
Operation,notebo okNotebook
This chapter describes the basics for operating your notebook. Please refer to
"Connecting external devices", Page 54 for instructions on how to connect external
devices such as a mouse and a printer to the notebook.
Please refer to the notes in the chapter "Important notes", Page 13.
Status indicators
Statusindicators
The status indicators provide information about the status of the power supply,
the drives and the keyboard functions.
20 Fujitsu
Working with the notebook
Key Description
Power-on indicator/Standby
StandbyindicatorPower-onindicator
• The indicator is illuminated: The notebook is switched on.
• The indicator flashes: The notebook is in standby mode.
• Indicator is off: The notebook is switched off.
Battery charging indicator/AC connection
The battery charging level is shown by the rechargeable battery indicator.
• The indicator light is green: The rechargeable battery is charged or no
rechargeable battery is inserted.
• The indicator light is orange: The AC adapter is connected and the rechargeable
battery is being charged.
•Theindicatorisflashing orange: The AC adapter is connected but the
rechargeable battery cannot be charged as the battery is too hot or too cold
for charging. The charging process is continued as soon as the rechargeable
battery has reached a permissible temperature again.
• The indicator is flashing red: a fault has occurred.
• The indicator is not lit up: The AC adapter is not connected.
Battery indicator
• The indicator light is green: The rechargeable battery is charged to between
51% and 100% of its maximum capacity.
• The indicator light is orange: The rechargeable battery is charged to between
13% and 50% of its maximum capacity.
•Theindicatorl
ights up red: The rechargeable battery is charged to between
0% and 12% of its maximum capacity.
• The indicator is flashing red: a fault has occurred.
BatterystatusindicatorBatterysymbolBatteryindicator
Drive indicator
DriveindicatorIndicator
The indicator is illuminated: One of the drives (e.g. hard disk, CD/DVD) is being
accessed.
Wireless indicator
• The indicator is illuminated: The wireless components are switched on.
• Indicator is off: The wireless components are switched off.
Num Lock indicator
Indicator
NumLock
The indicator is illuminated: The Num key has been pressed. The virtual number
keys have been activated. You can output the characters indicated on the upper
right of the keys.
Caps Lock indicator
IndicatorCapsLock
The indicator is illuminated: The Caps Lock key has been pressed. All the
characters you type will appear in upper case. In the case of overlay keys, the
character printed on the upper left of the key will appear when that key is pressed.
Scroll Lock indicator
Indicator
ScrollLock
The indicator is illuminated: The key combination Fn +Scroll Lock has been
pressed. The effect that this key has varies between applications.
Energy saving functions indicator
• The indicator is illuminated: One of the energy saving functions is activated.
•The
indicator is not lit up: The energy saving functions are deactivated.
Fujitsu 21
Working with the notebook
Switching the notebook on
►Open the LCD screen.
Switchingon
►Press the ON/OFF button for about one
second to switch the notebook on.
The power-on indicator of the notebook is lit.
Switching the notebook off
Back up your data and close all applications before you switch off your
device. Otherwise data might be lost.
►Shut down the operating system correctly.
Notebook
►If the notebook is not switched off
automatically, press the ON/OFF button
for approx. five seconds.
►Close the LCD screen.
22 Fujitsu
Working with the notebook
Keyboard
KeyboardNumeric key padNumber keypadkey s
The keyboard of your notebook is subject to continuous wear through normal
use. The key markings are especially prone to wear. The key markings are
liable to wear away over the life of the notebook.
The keyboard has been designed to provide all the functions of an enhanced keyboard.
Some enhanced keyboard functions are mapped with key combinations.
The following description of the keys applies to the Windows operating system. Additional functions
supported by the keys are described in the relevant manuals supplied with your application programs.
The following illustration shows how to access the different characters on keys with overlaid
functions. The example applies when the Caps Lock key has not been activated.
The illustration may differ from your device.
0
=
}
+
+
Num
Alt Gr
=
0}
=
0}
=
0}
=
0}
Fujitsu 23
Working with the notebook
Key Description
Backspace key
The Backspace key deletes the character to the left of the cursor.
BackspacekeyBac kspace
Tab key
The Tab key moves the cursor to the next tab stop.
Tabkey
Enter key (return)
The Enter key terminates a command line. The command you have entered
is executed when you press this key.
EnterkeyReturnEnterLinefeed
Caps Lock
Caps Lock key
The Caps Lock key activates the Caps Lock mode, and the corresponding
icon is displayed in the Windows information area. In Caps Lock mode, all
of the characters you type appear in upper case. In the case of overlay
keys, the character printed on the upper left of the key will appear when
that key is pressed. To cancel the Caps Lock function, simply press the
Caps Lock key again.
CapsLockkeyCaps Lock
Shift
Shift key
The Shift key causes uppercase characters to appear. In the case of overlay
keys, the character printed on the upper left of the key will appear when
thatkeyispres
sed.
ShiftkeyShift
Fn key
The Fn key enables the special functions indicated on overlay keys (see
"Key combinations", Page 26).
Fnkey
Cursor keys
The cursor keys move the cursor in the direction of the arrow, i.e. up, down,
left, or right.
CursorkeysCursorcontrol
Windows key
The Windows key switches between the start screen and the last used
application.
Windowskey
Menu key
The Menu key opens the menu for the active application.
24 Fujitsu
Working with the notebook
Virtual number keys
NumerickeypadVirtual number keysNumLock
LIFEBOOK E544 has virtual number keys, LIFEBOOK E554 has
a separate number keypad.
Virtual number keys are provided so that the keys of a number keypad can be used for certain
applications. The virtual number keys are recognizable on the keyboard by the numbers and
symbols printed in the upper right corner of each key. If you have switched on the virtual number
keys, you can output the characters shown on the upper right of the keys.
The key assignment shown below may be different from the
keyboard layout of your device.
&*
:
;
<>?
/
789
456
123+
/
1 = Character valid when the Num
key is not active
2 = Character valid when the Num
keyisactive
Further information about the status indicators can be found in chapter "Status indicators", Page 20.
Fujitsu 25
Working with the notebook
Separate number keypad
NumerickeypadSeparate num berkey padNumLock
LIFEBOOK E544 has virtual number keys, LIFEBOOK E554 has
a separate number keypad.
The keyboard of your LIFEBOOK E554 notebook has a separate number keypad on the far right.
Key combinations
Keycombinations
The following description of key combinations applies to Windows operating systems. Some of the
following key combinations may not function in other operating systems or with certain device drivers.
Other key combinations are described in the relevant manuals supplied
with your application programs.
Key combinations are entered as follows:
►Press the first key in the combination and keep it pressed.
►While holding the first key down, press the other key or keys in the combination.
Combination Description
Switch the speakers on and off
This key combination switches your notebook’s speakers off and
on.
Fn+F3S peakerSpeaker
Switch the touchpad and touchpad buttons on/off
This key combination switches the touchpad and the touchpad
buttons on or off.
Fn+F4
Tou chpa d
Tou chpa dbuttons
Tou chpa d
26 Fujitsu
Working with the notebook
Combination Description
Decrease the brightness of the screen
This key combination decreases the brightness of the screen.
Fn+F6LC DscreenB rightnessof thescreen
Increase the brightness of the screen
This key combination increases the brightness of the screen.
Fn+F7B rightnessof thescreen
Decrease the volume
This key combination reduces the volume of the internal speakers.
Fn+F8Vo lume
Increase volume
This key combination increases the volume of the internal
speakers.
Fn+F9Vo lume
Switch between display outputs
Use this key combination to select which monitor is used for
display if an external monitor is connected.
Display output is possible:
• only on the notebook’s LCD screen
• on the LCD screen of the notebook and the external monitor
atthesametime
• only on the external monitor
This setting is useful if you would like a high resolution and a
high refresh rate on an external monitor.
Fn+F10Switchingbetweendisplayoutputs
Switch betweenopenapplications
Use this key combination to switch between several open
applications.
Alt+Tab
AltCtrl Del
++
Windows security/Task Manager
This key combination opens the Windows security/Task Manager
window.
Ctrl+Alt+Del
Shift
Back tab
This key combination moves the cursor back to the previous tab
stop.
Shift+TabBacktab
Key combinations using the Windows keys are detailed in the manual
for your operating system.
Fujitsu 27
Working with the notebook
Country and keyboard settings
►Make the country and keyboard settings as described in the documentation for your operating
system.
Application keys (ECO and Wireless)
Applicationkeys
Your notebook is equipped with two application keys.
Key Description
Eco button (E key)
TheEkeyisac
onvenient way of activating and deactivating energy saving functions
(e.g. reducing the brightness of the screen), see also "Using the energy saving
functions", Page 40.
If the device is switched off, you can check the battery charging level with this key. After
pressing this key, the battery indicator will illuminate briefly. For a description of the
indicator colors, see "Status indicators", Page 20.
Wireless device switch
This application key is used to start the WirelessSelector software. The wireless
components that have been activated in the BIOS Setup canbeswitchedonandoff
individually.
28 Fujitsu
Working with the notebook
Touchpad and touchpad buttons
Keep the touchpad clean. Protect it from dirt, liquids and grease.
TouchpadTouchpad
Do not use the touchpad if your fingers are dirty.
Do not rest heavy objects (e.g. books) on the touchpad or the touchpad buttons.
2
1
1= Touchpad
2 = Touchpad buttons
The touchpad enables you to move the mouse pointer on the monitor.
The touchpad buttons allow you to select and execute commands. They correspond
to the buttons on a conventional mouse.
You can also deactivate the touchpad via a key combination, so that you cannot move
the pointer on the monitor unintentionally (see chapter "Key combinations", Page 26).
Moving the pointer
►Move your finger on the touchpad.
Touchpad
The pointer will move.
Selecting an item
►Move the pointer to the item you wish to select.
Touchpad
►Tap the touchpad once or press the left button once.
The item is selected.
Executing commands
►Move the pointer to the field you wish to select.
Touchpad
►Tap the touchpad twice or press the left button twice.
The command is executed.
Fujitsu 29
Working with the notebook
Dragging items
►Select the desired item.
Touchpad
►Press and hold the left button and drag the item to the desired position
with the finger on the touchpad.
The item will be moved.
LCD screen
LCDscreenNotes
Background lighting
LCD screens are operated with background lighting. The luminosity of the background
lighting can decrease during the period of use of the notebook. However, you can
set the brightness of your monitor individually.
Synchronizing the display on the LCD screen and an external monitor
For more information, please refer to Chapter "Key combinations", Page 26
under "Switching between display outputs".
30 Fujitsu
Working with the notebook
Webcam
Webcam
Depending on the configuration, your device may include an integral webcam.
Depending on the software used, you can use your webcam to take pictures,
record video clips or take part in web chats.
The webcam has its own status indicator. The indicator lights up when the webcam is active.
• The picture quality depends on the lighting conditions and the software being used.
• You can only operate the webcam with a particular application (e.g. an Internet telephony
program or a video conferencing program which supports a webcam).
• When using the webcam, the notebook base must not wobble.
• The webcam automatically adjusts itself to the current light level. For this reason
the LCD display may flicker while the light level is adjusted.
Further information on use of the webcam and additional settings for your webcam
can be found in the help function of the program using the webcam.
Fujitsu 31
Working with the notebook
Rechargeable battery
BatteryBatteryServicelife,batteryRechargeablebatteryBattery
During use as a portable, the notebook runs on its built-in battery. You can increase
the service life of the battery by caring for the battery properly. The average battery
service life is around 500 charge/discharge cycles.
You can extend the battery service life by taking advantage of the available energy saving functions.
Charging, caring for and maintaining the battery
BatteryBattery
The notebook battery can only be charged if the ambient temperature is between
5°C / 41°F and a maximum of 35°C / 95°F.
You can charge the battery by connecting the notebook to the AC adapter
(see "Connecting the AC adapter", Page 18).
If the battery is running low you will hear a warning alarm. If you do not connect the AC adapter
within five minutes of the warning alarm described above, your notebook will automatically switch off.
Monitoring the battery state of charge
Batterybat tery charge meter
Windows also has a "Battery charge meter" in the taskbar for monitoring the
battery capacity. When you place the mouse pointer on the battery symbol, the
system displays the state of charge of the battery.
Battery storage
BatteryBatterySelf-discharge,batteryChar gecapacity,batter y
The battery should be stored in a dry environment at a temperature between 0°C / 32°F and
30°C / 86°F. The lower the storage temperature, the lower the rate of self-discharge.
If you will be storing batteries for a longer period (more than two months),
the battery charge level should be approx. 30%. To prevent exhaustive
discharge which would permanently damage the battery, check the level
of charge of the battery at regular intervals.
To be able to make use of the optimum capacity of the battery, you should allow
the battery to fully discharge and then recharge it.
If you will not use batteries for long periods, remove them from the
notebook. Never store batteries in the device.
Removing and installing the battery
Only use batteries approved by Fujitsu for your notebook.
Never use force when fitting or removing a battery.
Make sure that no foreign bodies get into the battery connections.
Never store a battery for long periods in the discharged state. This
can make it impossible to recharge.
32 Fujitsu
Working with the notebook
Removing a rechargeable battery
►Prepare for removal, see chapter "Preparing to remove components", Page 62.
3
1
2
►Slide the slider switch in the direction of the arrow (1) and hold it in place.
►Slide the slider switch in the direction of the arrow (2).
►Remove the rechargeable battery from the battery compartment (3).
Fujitsu 33
Working with the notebook
Installing a rechargeable battery
2
1
►Position the rechargeable battery at the edge.
►Insert the rechargeable battery into the battery compartment until it engages positively (1).
►Slide the slider switch in the direction of the arrow (2).
►Complete the installation, see chapter "Finishing component removal", Page 68.
34 Fujitsu
Working with the notebook
Modular bay devices
ModularbayModularbay devic es
The design of your notebook enables the flexible use of notebook batteries and drives. The
following modular bay devices can be operated in the modular bay of your notebook:
• Second hard disk drive
• DVD Super Multi
• Weight saver
Only use modular bay devices designed for your notebook.
Do not use force when installing or removing the modular bay device.
Make sure that no foreign objects enter the modular bay.
You can swap modular bay devices during operation. This means you
do not need to switch off the notebook.
Log off the modular bay device via the corresponding symbol in the task bar.
The modular bay device can now be removed without any further actions being necessary.
Removing a modular bay device
2
1
Modularbay deviceDriveWeightsaver
►Slide the release mechanism (1) in the direction of the arrow and hold.
►Pull the modular bay device (2) out of the modular bay.
Fujitsu 35
Working with the notebook
Installing a modular bay device
►Place the modular bay device into the modular bay so that the contacts enter first.
►Push the modular bay device into the modular bay until you feel it lock into place.
Optical drive
Opticaldrive
This product contains a light-emitting diode, classified in accordance with IEC
608251:2007: LASER CLASS 1, and therefore must not be opened.
Handling optical disks
Opticaldisks
Observe the following guidelines when handling optical disks:
• Avoid touching the surface of an optical disk. Only hold the optical disk at the edge.
• Always store the optical disk in its case. This will prevent the optical disk from
becoming dusty, scratched or damaged in any other way.
•Protecty
our optical disk against dust, mechanical vibrations and direct sunlight.
• Do not store an optical disk in areas subject to high temperatures or humidity.
You may use 8 cm / 3.15 inch or 12 cm / 4.7 inch diameter optical disks in the drive.
When using a poor quality optical disk, vibrations and read errors may occur.
36 Fujitsu
Working with the notebook
CD/DVD indicator
CD/DVDindicator
The CD/DVD indicator flashes when an optical disk is inserted. The indicator goes out when the
drive is ready for reading. The indicator lights up when the drive is being accessed. You must
never remove the optical disk under any circumstances while the indicator is lit.
If the CD/DVD indicator does not go out after inserting an optical disk, but instead
continues to flash, this means that the drive cannot access the optical disk.
Either the optical disk is damaged or dirty or you are using an optical
disk that the drive cannot read.
Inserting or removing an optical disk
OpticaldiskOpticaldisk
The notebook must be switched on.
2
1
►Push the insert/eject button (1).
The drive tray will open.
►Gently pull the drive tray (2) completely out.
►Place the optical disk in the drive tray with
the printed side facing upwards.
or
►Remove an inserted optical disk.
►Push in the drive tray again until
you feel it lock into place.
Fujitsu 37
Working with the notebook
Manual removal (emergency removal)
CD/DVDManualremovalofopticaldiskEmergencyrem ovalofoptica ldisk
In the event of a power failure or damage to the drive, it may be necessary
to manually remove the optical disk.
1
2
►Switch your notebook off.
►Push a pen or a piece of wire (such as a
paper clip) firmly into the opening (1).
The drive tray will be ejected. You can now
pull the drive tray (2) out of the drive.
Removing and replacing the removable dust filter
To ensure optimum cooling of your notebook’s components, you should clean
the ventilation slots of the heat sink after prolonged use.
This ensures optimum fan performance. You can achieve the best cleaning
results with a small hand-held vacuum cleaner.
If necessary, useadrybrushtoremovedustfromtheventilationslots.
Do not use any cleaning liquids! Ensure that no liquid enters the device.
To avoid overheating of the device, do not remove the removable dust
filter when the device is switched on.
►Prepare for removal, see chapter "Preparing to remove components", Page 62.
38 Fujitsu
Working with the notebook
1
2
►Press and hold the lock of the removable
dust filter (1) and remove it from
its location (2).
►Clean the dust chamber.
1
►Insert the removable dust filter into its
location (1) at an angle as shown, and
ensure that you feel it click into place.
►Complete the removal, see chapter
"Finishing component removal", Page 68.
Fujitsu 39
Working with the notebook
Using the energy saving functions
EnergyEnergyBattery
The notebook uses less power when the available energy-saving functions are used. You will
then be able to work longer when using the battery before having to recharge it.
The energy efficiency is increased and environmental pollution is reduced.
By choosing the best power options, you can make significant savings and
at the same time help protect the environment.
When you fold down and close the LCD screen, depending on the setting in Windows,
the notebook automatically enters a power saving mode.
►Set the energy saving functions in your Control Panel.
►Set the screen saver in your Control Panel.
or
►Right-click on the desktop. Activate the screen saver by clicking on Personalize – Change
Screen Saver.
If you need further information about an option, you can get help with most
settings by pressing F1 to open the Microsoft Help.
When the notebook is in energy saving mode, the following must be remembered:
During energy saving mode, open data is held in main memory or
in a swap file on the hard disk.
Never switch the notebook off while it is in an energy saving mode. If the built-in battery
is nearly flat, close all open files and do not go into energy saving mode.
If you do not intend to use your notebook for a long period of time:
►Exit energy saving mode if necessary by moving the mouse, making an entry at the keyboard
or by switching on the notebook.
►Close all opened programs and completely shut down the notebook.
40 Fujitsu
Working with the notebook
Memory cards
Slot
Your notebook is equipped with an integrated memory card reader.
Follow the manufacturer’s instructions when handling the memory cards.
Memorycard
Supported formats
Your notebook supports the following format:
• Secure Digital (SDTM Card)
Inserting the memory card
►Carefully slide the memory card into the
slot. The label should be facing upward. Do
not apply excessive force, as otherwise the
delicate contact surfaces could be damaged.
Memorycard
Depending on the particular type
used, the memory card may protrude
slightly from the slot.
Removing the memory card
Memorycard
To avoid any loss of data, always follow the correct procedure for removing the
card (see the documentation for your operating system).
1
2
►On devices with card locking: Press
on the memory card (1).
Memorycard
The memory card is released and
can now be removed.
►Pull the memory card out of the slot (2).
Fujitsu 41
Working with the notebook
Speaker and microphones
MicrophoneSpeakerSubwooferVolumec ontro l
You can find information about the exact position of the speaker and microphones
in chapter "Ports and operation controls", Page 9.
Please refer to chapter "Key combinations", Page 26 for information on setting the volume
and also enabling/disabling the speakers using key combinations.
If you attach an external microphone, the built-in microphone is disabled.
When you connect headphones or external speakers, the built-in speakers are disabled.
You can find information on connecting headphones and a microphone in
chapter "Connecting external devices", Page 54.
Wireless LAN/Bluetooth components
The installation of wireless components not approved by Fujitsu will
invalidate the certifications issued for this device.
Switching the wireless components on and off
►Press the buttontostarttheWirelessSelector.
The wireless indicator will illuminate when one or more wireless components are switched on.
If you switch off the wireless components, the wireless LAN antenna
and the Bluetooth will also be switched off.
You can activate and deactivate the installed wireless components
individually using the WirelessSelector program
Pay attention to the additional safety notes for devices with wireless components
provided in the "Safety/Regulations" manual.
Details on using a wireless LAN can be found in the online help system
included in the wireless LAN software.
You can find more information on how to use Bluetooth on the CD you
received with your Bluetooth software.
Further information on WLAN and Bluetooth
For further information about WLAN or Bluetooth, please refer to the
appendix of this Operating Manual.
For WLAN specifications, see chapter "WLAN specifications", Page 79.
42 Fujitsu
Working with the notebook
Ethernet and LAN
EthernetLAN
The internal network module of your notebook supports Ethernet LAN. You can use it to
establish a connection to a local network (LAN = Local Area Network).
2
1
►Connect the network cable to the LAN
port of the notebook (1).
►Connect the network cable to your
network connection (2).
Your network administrator can help you to configure and use the LAN connections.
The network cable is not included in the delivery scope. This type of
cable can be obtained from a specialist dealer.
Fujitsu 43
Working with the notebook
Your port replicator
Your port replicator is a device that helps you to quickly connect your notebook to
your peripheral devices, such as a monitor, printer, etc.
The features offered by the port replicator include standard ports for
monitor, audio, mouse and keyboard.
You need only dock the notebook in order to work with your peripheral devices.
Ports on the port replicator
PortreplicatorPorts
11
1
2
3
4
6
7
89
12
10
5
1=SecurityL
ock device
2 = USB ports (USB 3.0)
3 = eSATA port
4 = LAN port
5 = Display Port
6 = DVI-D monitor port
7=Extern
al monitor port (VGA)
8 = DC input connector (DC IN)
9 = Headphones and microphone port
10 = ON/OFF button
11 = Connector on the port replicator for the
docking port on the bottom of the notebook
12 = Unlocking lever
The DVI port and Display Port cannot be used at the same time.
44 Fujitsu
Working with the notebook
Connecting the notebook to the port replicator
When the notebook is used in combination with the port replicator, the AC
adapter must always be connected to the port replicator.
We recommend that the notebook is not operated with the LCD screen closed when
the notebook is connected to the port replicator. The resulting overheating can cause
reduced performance and increased activity of the integrated fan.
Portreplicator
►If the AC adapter is plugged into the power outlet, unplug it from the power outlet.
►Disconnect the AC adapter from the notebook.
1
►Position the notebook so that it is in line with the back edge of the port replicator.
►Place the notebook onto the port replicator (1) and ensure that it locks into place correctly.
Fujitsu 45
Working with the notebook
Connecting the AC adapter to the port replicator
3
1
2
►Connect the AC cable to the AC adapter (1).
►Plug the AC cable into the power outlet (2).
►Connect the AC adapter cable to the DC
jack (DC IN) of the port replicator (3).
When the notebook is connected to a port replicator, the operating system creates
a hardware profile for the "Docked" mode. In this profile, for example, the monitor
which was last used for output is saved as a setting. This profile will be loaded as
soon as the notebook is connected to a port replicator of the same type.
Switching on the notebook via the port replicator
►Press the ON/OFF button on the port
replicator to switch the notebook on.
The power-on indicator of the port
replicator lights up.
46 Fujitsu
Working with the notebook
Disconnecting the notebook from the port replicator
Problems may occur if the notebook is removed from the port replicator during
operation. We recommend that the notebook is switched off or that the appropriate
undocking function provided by the operating system is executed.
►Switch the notebook off.
2
1
►Pull the unlocking lever in the direction of the arrow (1), until you hear the notebook unlatch.
►Lift off the notebook (2).
Fujitsu 47
Security functions
Security functions
Securityfunctions
Your notebook has a variety of security functions that you can use to protect your
system and your personal data from unauthorized access.
This chapter explains how to use these functions, and what the benefits are.
Please remember that in some cases, for example, forgetting your password,
you may be locked out of the system and unable to access your data.
Therefore, please note the following information:
• Make regular backups to external optical disks such as external hard
drives, CDs, DVDs or Blu-ray Discs.
• Some security functions need you to choose passwords. Make a note
of the passwords and keep them in a safe place.
If you forget your passwords you will need to contact our Service Desk.
Deletion or resetting of passwords are not covered by your warranty
and a charge will be made for assistance.
Configuring the fingerprint sensor
Fingerprintsens orFinger printsensor
Whether your device has a fingerprint sensor or not depends on the
device configuration which you ordered.
The fingerprint sensor can record the image of a fingerprint. With additional fingerprint
software, this image can be processed and used instead of a password.
1
►Install the fingerprint software to be able
to use the fingerprint sensor (1).
You can obtain further information on the fingerprint sensor in the
"appendix: Miscellaneous Information".
48 Fujitsu
Security functions
Using the Security Lock
Your device comes with a Security Lock mechanism for the Kensington Lock Cable. You
can use the Kensington Lock Cable, a sturdy steel cable, to help protect your notebook
from theft. The Kensington Lock Cable is available as an accessory.
Fujitsu recommends the use of a combination lock.
K
►Fit the Kensington Lock Cable to the
mechanism on your notebook.
KensingtonLoc kCabl eUsingthesecuri tyloc k
Mechanicalsec urityAnti-theftprotection
Attach another Kensington Lock Cable to your port replicator to protect
your port replicator from theft as well.
Configuring password protection in BIOS Setup Utility
Before using the various options for password protection in the BIOS Setup
Utility,ple
ase proceed as follows to increase data security:
Make a note of the passwords and keep them in a safe place. If you forget your
supervisor password you will not be able to access your notebook. Passwords are
not covered by your warranty and a charge will be made for assistance.
Password prote ction
Your password can be up to eight characters long and can contain letters and
numbers. No distinction is made between uppercase and lowercase.
Fujitsu 49
Security functions
Protecting BIOS Setup Utility (supervisor password
and user password)
If you have opened these operating instructions on the screen, we recommend
that you print them out. You cannot call up the instructions on the screen
while you are setting up the password.
BIOSSetupUtility
The supervisor password and the user password both prevent unauthorized use of the BIOS
Setup Utility. The supervisor password allows you to access all of the functions of the BIOS Setup
Utility, while the user password will only give you access to some of the functions. You can
only set up a user password if a supervisor password has already been assigned.
Calling and using the BIOS Setup Utility is described in the chapter
"Settings in BIOS Setup Utility", Page 69.
Assigning the supervisor and user passwords
►Start the BIOS Setup Utility and go to the Security menu.
►Select the Set Supervisor Password field and press the Enter key.
With Enter new Password: you are asked to enter a password.
►Enter the password and press the Enter key.
Confirm new Password requires you to confirm the password.
►Enter the password again and press the Enter key.
Changes have been saved is displayed as a confirmation that the new password has been saved.
►To set the user password, select Set User Password and proceed exactly as
when configuring the supervisor password.
If you do not want to change any other settings, you can exit BIOS Setup Utility.
►In the Exit menu, select the option Save Changes & Exit.
►Select Yes and press the Enter key.
PasswordSupervisor passwordUserpassword
The notebook is then rebooted and the new password comes into effect. It will now be necessary
to first enter your supervisor or user password in order to open the BIOS Setup Utility.Please
note that the user password only provides access to a few of the BIOS settings.
Changing the supervisor password or user password
You can only change the supervisor password when you have logged into the
BIOS Setup Utility with the supervisor password.
PasswordSupervisorpasswordUserpassword
►Start the BIOS Setup Utility and go to the Security menu.
►When changing the password, proceed exactly as when assigning a password.
50 Fujitsu
Security functions
Removing passwords
To remove a password (without setting a new password) perform the following steps:
PasswordSupervisorpasswordUserpassword
►Start the BIOS Setup Utility and go to the Security menu.
►Highlight the Set Supervisor Password or Set User Password field and press the Enter key.
You will be requested to enter the current password by the Enter Current Password prompt.
Enter New Password will appear and you will be requested to enter a new password.
►Press the Enter key twice at this request.
►In the Exit menu, select the option Save Changes & Exit.
►Select Yes and press the Enter key.
The notebook will now reboot with the password removed.
With the supervisor password, you simultaneously deactivate the user password.
Password protection for booting the operating system
With the supervisor password you have set in the BIOS Setup Utility (see
section "Assigning the supervisor and user passwords", Page 50), you can
also prevent booting of the operating system.
Operating system
Activating system protection
►Start the BIOS Setup Utility and go to the Security menu.
Operatingsystem
►Select the PasswordonBootoption and press the Enter key.
►Select the option you require (Disabled,First Boot or Every Boot) and press the enter key
►Select the Save Changes & Exit option under Exit.
The notebook will reboot. You will be prompted to enter your password (the supervisor password).
Deactivating system protection
►Start the BIOS Setup Utility and go to the Security menu.
Operatingsystem
►Select the PasswordonBootoption and press the Enter key.
►Select the Disabled option and press the Enter key.
If you do not want to change any other settings, you can exit BIOS Setup Utility.
►Select the Save Changes & Exit option under Exit.
The notebook will reboot. The system is no longer password-protected.
Password protection for the hard disk
If a supervisor password was set, an additional password for the hard disk
canbes
et in the Hard Disk Security menu.
The hard disk is protected by this password. Data on this hard disk can then only be
read in another system if the correct password is entered.
Fujitsu 51
Security functions
Trusted Platform Module - TPM (device dependent)
TPMTrusted P latform Module
To use the TPM, you must enable the TPM in the BIOS Setup before the software
is installed. The condition for this is that you have assigned at least the supervisor
password (see "Security functions", Page 48).
Enabling TPM
• Requirement: You have assigned a supervisor password (see "Security functions", Page 48).
►Call BIOS Setup and select the Security menu.
►Mark the TPM (Security Chip) Setting field and press the Enter key.
►Select the "Security Chip" "Enabled" entry to enable the TPM
Once you have enabled the TPM by rebooting, the Clear Security Chip menu item appears.
If the TPM was already in use, you can use Clear Security Chip to clear the holder in the
TPM. With Enabled,a
ll secret keys (e.g. SRK - Storage Root Keys, AIK - Attestation
IdentityKeysetc.
) generated by applications are deleted.
Take note that you can then no longer access the data you have
encrypted on the holder-based keys!
►Select the Exit Saving Changes option in the Exit menu.
►Press the Enter key and select Yes .
The notebook restarts and the TPM is switched on after the reboot.
Disabling TPM
• Requirement: You have assigned a supervisor password (see "Security functions", Page 48).
►Call BIOS Setup and select the Security menu.
►Mark the TPM (Security Chip) Setting field and press the Enter key.
►Select the "Security Chip" "Disabled" entry to deactivate the TPM.
►From the Exit menu, choose the option Exit Saving Changes.
►Press the Enter key and select Yes .
The notebook will now reboot with TPM deactivated.
52 Fujitsu
Security functions
Smart Card reader
SecurityfunctionsSecurityfunctions
Smart Cards are not supplied as standard equipment. You can use all Smart Cards that comply with
the ISO standard 7816-1, -2 or -3. These Smart Cards are available from various manufacturers.
With the appropriate software you can use your Smart Card as an alternative to password
protection, but also as a digital signature, for encrypting your e-mails or for home banking.
We recommend that you always use two Smart Cards. Always keep one of the Smart Cards
in a safe place if you are carrying the other Smart Card with you.
Inserting the Smart Card
Do not use force when inserting and removing the Smart Card.
Make sure that foreign objects do not fall into the Smart Card reader.
►Slide the Smart Card into the Smart
Card reader with the chip facing upwards
(or downwards depending on the
device) and to the front.
Fujitsu 53
Connecting external devices
Connecting external devices
Under all circumstances, please observe the safety notes provided in the
"Important notes", Page 13 chapter before connecting or disconnecting
any devices to or from your notebook.
Always read the documentation supplied with the device you wish to connect.
Never connect or disconnect cables during a thunderstorm.
Never pull at a cable when disconnecting it. Always grasp the plug.
Follow the steps in the sequence below when connecting or disconnecting
devices to your notebook:
With some devices such as USB devices, it is not necessary to switch off
the notebook and the device before connecting/disconnecting. For more
information about whether or not devices need to be switched off, please refer
to the documentation supplied with the external device.
Some of the external devices require special drivers (see the operating
system and external device documentation).
54 Fujitsu
Connecting external devices
Connecting an external monitor
An analog monitor is connected to the analog external monitor port (VGA), a digital
monitor to the Display Port or to the DVI-D monitor port on the optional port replicator.
The display output is limited to a maximum of two monitors at any one time (see "Key
combinations", Page 26, section "Toggle display output").
MonitorVGA socketM onitorportMonito rport
Digital Display Port (on notebook or on optional
port replicator)
Analog external monitor port (VGA) (on
notebook or on optional port replicator)
Digital DVI-D monitor port (on optional port
replicator)
►Switch off the notebook and the external monitor.
►Plug the data cable of the external monitor into the monitor port.
►First switch on the external monitor and then the notebook.
You can also switch back and forth between the external monitor and the LCD
screen of the notebook, see chapter "Key combinations", Page 26.
You can display the same picture on the external monitor and the
notebook LCD screen simultaneously.
If you wish to operate the screen via a DVI port, use the port replicator
which is available as an option for your notebook.
Fujitsu 55
Connecting external devices
Connecting external devices to the serial
port (optional)
Serialport,serialportExternaldevices,Devices,
External devices (e.g. a printer or modem) can be connected to the optional serial port.
►Connect the data cable to the
external device.
►Connect the appropriate data cable for
the device to the serial port.
For an exact description of how to connect external devices to the corresponding
port, please refer to the documentation for the external device.
Port settings
Serialport
You can change the port settings (e.g. address, interrupt) in the BIOS Setup.
Device drivers
Devicedrive rs
Devices connected to the serial port require drivers. Your operating system
already includes many drivers. If the required driver is missing then it will be
necessary to install it. Up-to-date drivers are usually available on the Internet
or will be supplied with the device on an optical disk.
56 Fujitsu
Connecting external devices
Connecting USB devices
USBports
On the USB ports you can connect external devices that also have a USB port
(e.g. a DVD drive, a printer, a scanner or a modem).
USB devices are hot-pluggable. This means you can connect and disconnect the
cables of USB devices while the operating system is running.
USB 1.x has a maximum data transfer rate of 12 Mbps.
USB 2.0 has a data transfer rate of up to 480 Mbps.
USB 3.0 has a data transfer rate of up to 5 Gbps.
Additional information can be found in the documentation for the USB devices.
►Connect the data cable to the
external device.
►Connect the data cable to a USB
port of the notebook.
Device drivers
USB devices will be automatically recognized and installed by your operating system.
Fujitsu 57
Connecting external devices
USB port with charging function (Anytime USB charge)
USBchargingfunction
It is recommended that the notebook be operated with the AC adapter connected
whenever the USB port with charging function is in use, as this function will drain
the battery more quickly if an external USB device is being charged.
The AC adapter must already be connected when the notebook is switched
off, as otherwise the USB charging function will be disabled and the
connected USB devices will not be charged.
Some USB devices (e.g. mobile telephony) require a driver in order to utilize the USB
charging function. In this case the USB charging function will not work when the
notebook is switched off, as no drivers are active when the notebook is switched off.
You can use this USB port to charge or supply power to a USB device (e.g. to charge a PDA
or a mobile phone or to connect a USB lamp), even if the notebook is switched off.
58 Fujitsu
Connecting external devices
Connecting an external SATA hard drive (eSATA)
(port replicator only)
The notebook itself does not have an eSATA port. The port replicator which is
available as an option for your notebook offers you this type of port.
An external SATA hard disk can be connected at the eSATA port. This allows you
to expand the internal hard disk capacity as you wish.
The length of the eSATA cable must not exceed 2 meters. Seek advice from a specialty
store as to which eSATA data cable is suitable for your external eSATA hard disk.
Note that the hard drive has its own external power supply available.
The data transfer rate is up to 2,400 Mbps.
eSATA
►Connect the data cable to the external
device.
►Connect the data cable to the eSATA port.
Device drivers
The eSATA hard disk is automatically recognized by your operating system and installed.
You w ill find more information in the documentation for the external SATA
hard disk and the operating system.
Safe removal of eSATA and USB devices
Always correctly remove the device according to the rules described below,
to ensure that none of your data is lost.
►Click on the symbol for safe removal of hardware with the left mouse button.
►Select the device you wish to shut down and remove.
►Press the "Enter" key.
Wait for the dialog box which tells you that it is now safe to remove the device.
Fujitsu 59
Connecting external devices
Connecting external audio devices
Microphone port/Line In
Connectingaudio dev icesAudioconnectionsConnectingmicrophone
The microphone port/Line In allows you to connect an external microphone, a MiniDisc
player, MP3 player, CD player or a tape deck to your notebook.
►Connect the audio cable to the
external device.
►Connect the audio cable to the microphone
port/Line In of the notebook.
Headphones port
Connectingaudiodevices
Audioconnections
Connectingheadphones
You can connect headphones or external speakers to your notebook via the headphones port.
►Connect the audio cable to the
external device.
►Connect the audio cable to the headphones
port of the notebook.
The internal speakers are disabled.
If you buy a cable from a retailer, please note the following information:
The headphones port on your notebook is a "3.5 mm jack".
If you want to connect headphones or speakers you will need a "3.5 mm jack plug".
60 Fujitsu
Removing and installing components during servicing
Removing and installing components
during servicing
Only qualified technicians should repair your notebook. Unauthorized
opening or incorrect repair may greatly endanger the user (electric shock,
fire risk) and will invalidate your warranty.
Components
Incaseofservice
You may remove and install the components described in this chapter yourself
after consulting the Hotline/Service Desk.
If you remove and install components without consulting the Hotline/Service
Desk, then the warranty of your notebook will be voided.
Notes on installing and removing boards
and components
• Switch off your notebook and remove the AC plug from the power outlet.
• Always remove the battery.
• Take care when you use the locking mechanisms for the battery and any other component.
• Never use sharp objects such as screwdrivers, scissors or knives as a lever to remove covers.
InstructionsBoardsESD
Boards with electrostatic sensitive devices (ESD) are marked with the label
shown.
When handling boards fitted with ESDs, you must always observe the following
points:
• You must always discharge static build up (e.g. by touching a grounded
object) before working with boards.
• The equipment and tools you use must be free of static charge.
• Remove the AC plug from the power outlet before inserting or removing
boards.
• Always hold boards by their edges.
• Never touch connector pins or conductors on the board.
Fujitsu 61
Removing and installing components during servicing
Preparing to remove components
If you are going to remove or change system components, prepare for the removal as follows:
Please observe the safety information in chapter "Important notes", Page 13.
Remove the AC plug from the power outlet!
►Switch the device off.
The device must not be in energy saving mode.
►Close the LCD screen.
►Remove all the cables from the device.
►Turn the device over and place it on a stable, flat and clean surface. If necessary, lay an
anti-slip cloth on this surface to prevent the device from being scratched.
►Remove the battery,see"Removing a rechargeable battery", Page 33.
Removing and installing memory expansion
MemorymoduleMainmemoryMemoryremovalSystemexpansion
Systemexpansi on
If you are asked by the Hotline/Service Desk to remove or install a memory
expansion module yourself, proceed as follows:
Please observe the safety information in chapter "Important notes", Page 13.
During installation/removal of memory modules, the battery must remain
removed from the notebook and the notebook must not be connected to the
AC adapter, see "Preparing to remove components", Page 62.
Only use memory modules that have been approved for use in your
notebook (see chapter "Technical data", Page 78).
Never use force when installing or removing a memory module.
Make sure that no foreign objects fall into the memory upgrade compartment.
You must open the memory upgrade compartment to remove or install a memory
module. On some devices, it is possible that opening the compartment exposes various
components. Only authorized specialists are permitted to remove or change these
components. Therefore, be sure to observe the following:
Individual components can become very hot during operation. Therefore, we
recommend that you wait one hour after switching the notebook off before removing
or installing memory modules. Otherwise, there is a risk of suffering burns!
As some components are exposed that are sensitive to static electricity, please take
note of chapter "Notes on installing and removing boards and components", Page 61.
62 Fujitsu
Removing and installing components during servicing
Removing the cover
►Prepare for removal, see "Preparing to remove components", Page 62.
1
2
►Remove the screw (1).
Keep the screw in a safe place.
►Lift the cover off the notebook (2).
Removing a memory module
3
2
1
1
►Carefully push the two mounting
clips outwards (1).
MemoryexpansionMemorymodule
The memory module will fold upwards (2).
►Pull the memory module out of its slot
in the direction of the arrow (3).
Fujitsu 63
Removing and installing components during servicing
Installing a memory module
2
a
1
►Insert the memory module with the contacts
and the recess (a) forward in the slot (1).
MemoryexpansionMemorymodule
►Carefully push the memory module
downwards until you feel it click
into place (2).
Attaching the cover
2
1
►Place the cover in the correct location (1).
►Tighten the screw (2).
►Complete the installation, see "Finishing component removal", Page 68.
64 Fujitsu
Removing and installing components during servicing
Removing and installing the harddisk
Removing the cover
1
2
►Remove the screw (1).
Keep the screws in a safe place. If you are removing more than one component at
the same time, store the screws for the individual components separate from each
other. If you install the wrong screws, components may be damaged.
The screws are not all the same length and when the cover is installed,
the correct screws must be used.
►Lift the cover off the notebook (2).
Fujitsu 65
Removing and installing components during servicing
Removing the hard disk
1
1
►To release the hard disk from the
contacts, pull the hard disk in the
direction of the arrow (1).
2
►Remove the hard disk from the hard
disk access compartment (2).
66 Fujitsu
Removing and installing components during servicing
Installing a hard disk
1
►Place the hard disk into the hard disk
access compartment (1).
2
2
►Pulltheharddiskinthedirectionofthe
arrow (2) until it engages in the contacts.
Fujitsu 67
Removing and installing components during servicing
Attaching the cover
2
1
►Place the cover in the correct location (1).
►Tighten the screw (2).
Finishing component removal
After you have removed or changed the system components as required, please
prepare your device for operation again as follows:
►Install the battery again, see "Installing a rechargeable battery", Page 34.
►Turn the notebook the right way up again and place it on a flat surface.
►Reconnect the cables that were previously disconnected.
68 Fujitsu
Settings in BIOS Setup Utility
Settings in BIOS Setup Utility
BIOSSetupUtilitySystemsettings,BIOSSetupUtilityConfiguration,BIOSS etupUtilitySetupConfiguring systemConfiguringhardware
The BIOS Setup Utility allows you to set the system functions and the hardware
configuration for the notebook.
When a notebook is delivered, the factory default settings are effective. You can change
these settings in the menus of the BIOS Setup Utility. Any changes you make take
effect as soon as you save and exit the BIOS Setup Utility.
The BIOS Setup Utility program contains the following menus:
About Displays information relating to the BIOS, processor and notebook
System Advanced system settings
Advanced Configuration of various hardware components, such as mouse, keyboard,
processor
Security Password settings and security functions
Boot Configuration of the start-up sequence
Exit Exits the BIOS Setup Utility
Starting the BIOS Setup Utility
►Reboot the device (switch off/on or reboot the operating system).
BIOSSetupUtility
The following message (or similar) appears on the screen briefly at startup:
<F2> BIOS Setup <F12> Boot Menu
►Press the function key F2 .
►If a password has been assigned, enter the password and press the Enter key.
If you have forgotten the password, contact your system administrator
or contact our customer service center.
The BIOS Setup Utility starts.
BIOS Setup Utility operation
BIOSSetupUtility
Press the F1 key to display help about operation of the BIOS Setup Utility. The description
of the individual settings is shown in the right-hand window of the BIOS Setup Utility.
With the F9 key you can load the default settings of the BIOS Setup Utility.
►Use the cursor keys ←or →to select the menu you wish to access to make changes.
The menu is displayed on the screen.
►Select the option you want to change with the cursor keys ↑or ↓.
►Press the "Enter" key.
►Press the ESC key to exit the selected menu.
►For future reference, make a note of the changes you have made (for example, in this manual).
Fujitsu 69
Settings in BIOS Setup Utility
Exiting BIOS Setup Utility
BIOSSetupUtility
You need to select the desired option in the Exit menu and activate it by pressing the Enter key:
Exit Saving Changes - save changes and exit BIOS Setup Utility
►To save the current menu settings and exit the BIOS Setup Utility, select Exit Saving Changes and Yes.
The notebook is rebooted and the new settings come into effect.
Exit Discarding Changes - Reject changes and
exit BIOS Setup Utility
►To discard the changes, select Exit Discarding Changes and Yes.
The settings in place when BIOS Setup Utility was called remain effective. BIOS
Setup Utility is terminated and the notebook is rebooted.
Load Setup Defaults – load default values
►To copy the standard entries for all menus of the BIOS Setup Utility,
choose Load Setup Defaults and Yes .
Discard Changes - Discard Changes without
exiting BIOS Setup Utility
►To discard the changes you have made, select Discard Changes and Yes .
The settings in place when BIOS Setup Utility was called remain effective.
You can now make additional settings in the BIOS Setup Utility.
►IfyouwanttoexittheBIOS Setup Utility with these settings, select Exit Saving Changes and Yes.
Save Changes - save changes without exiting
the BIOS Setup Utility
►To save the changes, select Save Changes and Yes.
The changes are saved. You can now make additional settings in the BIOS Setup Utility.
►If you want to exit BIOS Setup Utility with these settings, choose Exit Saving Changes and Yes .
Save changes and power off
►To save the changes and switch off your device, select Save Changes and Power Off and Yes .
The changes are saved. Your device is shut down.
70 Fujitsu
Troubleshooting and tips
Troubleshooting and tips
TroubleshootingTipsFaultProbl emsolving
If a fault occurs, try to correct it as described. If you fail to correct the problem, proceed as follows:
►Make a note of the steps and the circumstances that led to the fault. Also
make a note of any error messages displayed.
►Switch the notebook off.
►Please contact the Hotline/Service Desk.
You can contact Fujitsu Service and Support in the following ways:
• Toll free phone: 1-800-Fujitsu (1-800-838-5487)
• Website: "http://solutions.us.fujitsu.com/www/content/support/contact/index.php"
Before you place the call, have the following information ready so that the customer
support representative can provide you with the fastest possible solution:
• The model name and serial number of the notebook. The serial number is
located on a sticker on the underside of the notebook.
• Notes with the messages that appeared on the screen and
informationonaco
ustic signals.
• Any changes you have made to the hardware or software since
receiving the notebook.
• Any changes you havemadetotheBIOS Setup settings after receiving the notebook.
• Your system configuration and all peripheral devices connected to your system.
• Your sales contract.
Our notebooks have been designed primarily with mobile applications in mind.
This means that considerable effort has been made to optimize components and
equipment in terms of weight, space and energy requirements. Depending on the
particular configuration you have purchased, it is possible that functionality may be
slightly reduced compared to a desktop PC if you are running processor-intensive
gaming software, e.g. games with intensive 3D graphics. Updating your hardware with
drivers which have not been approved by Fujitsu may result in performance losses,
data losses or malfunction of the equipment. A list of approved drivers and current
BIOS versions can be downloaded from: "http://solutions.us.fujitsu.com"
Help if problems occur
Should you encounter a problem with your computer that you cannot resolve yourself:
►Note the ID number of your device. The ID number is found on the type rating
plate on the back or underside of the casing.
►For further clarification of the problem, contact the Fujitsu Service Desk. When you do
this, please have ready the ID number and serial number of your system.
Recovering your Factory Image
In the event you need to restore your original Factory Image, please refer to
the appendix of this Operating Manual.
Fujitsu 71
Troubleshooting and tips
The notebook’s date or time is incorrect
SummertimeWinter timeIncor recttimeTimenotcorrectWrongdate/timeDatenot correctChargi ngb ack-up battery
Cause Troubleshooting
Time and date are incorrect. ►With the BIOS-Setup-Utility,you can set the
date and time in the Main menu.
Date and time are still set incorrectly after
switching on the notebook.
►Please contact your sales outlet or our
hotline/service desk.
When certain characters are entered on the
keyboard, only numerals are written
Abeepsounds ever ys econd
Cause Troubleshooting
The virtual number keys of your device are
activated, see "Virtual number keys", Page 25
►Press the Num button.
The notebook’s LCD screen remains blank
LCDscreenBlankLCD screen
Cause Troubleshooting
Screen is switched off. ►Pressakeyortouchthe touchpad.
External monitor or television set connected. ►Press the key combination for changing over
the screen output, see "Key combinations",
Page 26.
The LCD screen of the notebook is difficult to read
LCDscreenLCDscreen
Cause Troubleshooting
Reflected glare ►Turn the notebook or alter the tilt of the LCD
screen.
►Increase the brightness of the screen.
72 Fujitsu
Troubleshooting and tips
The external monitor remains blank
Monitor
Cause Troubleshooting
Monitor is switched off. ►Switch the external monitor on.
Power saving has been activated (monitor is
blank).
►Press any key to continue.
Brightness is set to dark. ►Adjust the brightness of the monitor.
Screen output is set to the notebook’s LCD
screen
►Press the key combination for changing over
the screen output, see "Key combinations",
Page 26.
The external monitor’s AC cable or data cable is
not connected properly.
►Switch off the external monitor and the
notebook.
►Check whether the AC cable is plugged
properly into the external monitor and into
the power outlet.
►Check whether the data cable is properly
connected to the notebook and the external
monitor (if it is plugged in with a connector).
►Switch on the external monitor and the
notebook.
The external monitor is blank or the image is unstable
MonitorMonito r
Cause Troubleshooting
The wrong external monitor has been selected
or the wrong screen resolution has been set for
the application program.
►Terminate the application program under
Windows by pressing Alt +F4 .Ifthe
error persists after terminating the program,
use the key combination for switching the
screen output(see"Key combinations",
Page 26), in order to switch to the LCD
screen of the notebook.
Change the following setting:
►Set the screen resolution: Set the screen
resolution as described in the documentation
for your operating system.
►Select monitor: Select monitor 1 or 2 as
described in the documentation for your
operating system.
Fujitsu 73
Troubleshooting and tips
The notebook does not start after switching it on
Notebook
Cause Troubleshooting
The battery is not installed correctly. ►Check whether the battery is installed
correctly in its compartment.
►Switch the notebook on.
The battery is dead. ►Charge the battery.
or
►Insert a charged battery.
or
►Connect the AC adapter to the notebook.
The AC adapter is not connected properly. ►Check whether the AC adapter is properly
connected to the notebook.
►Switch the notebook on.
The notebook stops working
NotebookEnding
Cause Troubleshooting
The notebook is in energy saving mode. ►End energy saving mode.
An application program has caused the
malfunction.
►Close the application program or restart
the notebook (by restarting the operating
system or switching the device off and back
on again).
The battery is dead. ►Charge the battery.
or
►Insert a charged battery.
or
►Connect the AC adapter to the notebook.
The printer does not print
Printerdoesnot print
Cause Troubleshooting
The printer is not switched on. ►Make sure that the printer is switched
on and ready for operation (refer to the
documentation supplied with the printer).
The printer is not connected correctly. ►Check that the data cable connecting
the notebook to the printer is properly
connected.
The printer driver is faulty or not correctly
installed, or it is the wrong printer driver.
►Check whether the correct printer driver is
loaded (refer to the printer documentation).
74 Fujitsu
Troubleshooting and tips
The wireless connection to a network does not work
Thewireless connecti onto an etwork does not work
Cause Troubleshooting
The wireless component is switched off. ►Switch the wireless component on (see
"Switching the wireless components on and
off", Page 42).
The wireless component is switched on. Despite
this, the wireless connection to a network does
not work.
►Check whether the wireless connection is
enabled by the software.
►Further information on using the wireless
component can be found in the help files.
Acoustic warning
Acous tic wa rnin gsErrors
Cause Troubleshooting
A beep sounds every few seconds.
The battery is almost dead.
►Charge the battery.
Smart Card reader is not recognized
Cause Troubleshooting
Chip on Smart Card inserted incorrectly. ►Make sure you have inserted your Smart
Card into the Smart Card reader with
the chip facing upwards or downward
(depending on device).
►Check whether the Smart Card you are
using is supported. Your Smart Card must
comply with the ISO standard 7816-1, -2,
-3 and -4.
Smart Card PIN forgotten
Cause Troubleshooting
PIN forgotten ►If you are working in a network, contact your
system administrator, who can unlock your
notebook with a Supervisor PIN.
Smart Card lost
Cause Troubleshooting
Smart Card lost. ►If you are working in a network, contact your
system administrator, who can boot your
notebook with a Supervisor Smart Card.
Fujitsu 75
Troubleshooting and tips
Error messages on the screen
Errormessages on thes creenErrors
This section describes the error messages generated by the BIOS Setup. Error messages displayed
by the operating system or programs are described in the documentation for these programs.
If the error message appears repeatedly despite troubleshooting measures,
contact the place of purchase or our customer service center.
Error message/cause Troubleshooting
CMOS Battery Bad
If the error message occurs repeatedly, the
back-up battery in the notebook is dead.
►Contact your sales outlet or our customer
service center.
System CMOS checksum bad - Default configuration
used
The system configuration information is
incorrect.
►Switch the notebook off.
►Switch the notebook on.
►Press the function key F2 to access the
BIOS Setup.
►In the BIOS Setup, select the Exit menu.
►Select the entry Load Setup Defaults.
►Select OK and press the Enter key.
Extended memory failed at offset: xxxx Failing Bits:
zzzz zzzz
When testing the extended memory. an error
has resulted at the address xxxx.
►Check whether the additional memory
module has been inserted correctly.
Failure Fixed Disk n
The settings of the hard disk drive are incorrect.
►Start the BIOS Setup (Primary Master
submenu) and select the correct settings.
Keyboard controller error ►Switch the notebook off with the ON/OFF
button.
►Wait 3 - 5 seconds and switch on the
notebook again.
Keyboard error If you use an external keyboard:
►Check the connection and reboot the
notebook.
nn Stuck key ►Make sure that no key is pressed.
Operating system not found ►Check in the BIOS Setup whether your hard
disk has been set correctly.
►Make sure that the operating system is
installed on the corresponding drive.
Press <F1> to resume, <F2> to SETUP
This error message appears if an error occurs
during the self-test before starting the operating
system.
►Press the F1 function key to start the
operating system.
►Press the function key F2 to access the
BIOS Setup.
76 Fujitsu
Troubleshooting and tips
Error message/cause Troubleshooting
Previous boot incomplete - Default configuration
used Default values have been set for certain
settings because of an error which occurred in
the previous system boot. Check the settings in
the BIOS Setup.
►Press the F1 function key when prompted
to do so.
Real time clock error ►Contact your sales outlet or our customer
service center.
nnnnK Shadow RAM failed at offset: xxxx Failing
Bits: zzzz
►Contact your sales outlet or our customer
service center.
System battery is dead - Replace and run SETUP ►Contact your sales outlet or our customer
service center.
System cache error - Cache disabled ►Contact your sales outlet or our customer
service center.
System timer error ►Contact your sales outlet or our customer
service center.
Fujitsu 77
Technical data
Technical data
Technicaldata
LIFEBOOK
Technicaldata
LIFEBOOK E544 LIFEBOOK E554
Ambient conditions
Operating
temperature
41°F – 95°F / 5°C – 35°C
Transport temperature 5°F – 140°F / -15°C – 60°C
Dimensions
WidthxDepthx
Height
13.31 inch x 9.09 inch x 0.95-1.24
inch /
338 mm x 231 mm x 25.1 - 31.4 mm
14.72 inch x 9.84 inch x 0.95-1.24
inch /
374 mm x 250 mm x 24.2 -
31.4 mm
Weight approx. 4.19 lbs / approx. 1.9 kg approx. 4.63 lbs / approx. 2.1 kg
Main memory
Slots 2 slots 204-pin DDR3L-1600 SO-DIMM with a total of max. 16 GB RAM
Approved memory
modules
2 GB, 4 GB or 8 GB DDR3L-1600 SO-DIMM
78 Fujitsu
Technical data
WLAN specifications
Type of network x2 (SB) + BT (v4.0+HS) Intel WilkinsPead2(SB)
2x2 (11ac)+ BT (v4.0 + HS) Intel
WilkinsPeak2(11ac) (*1)
Transfer rate (Automatic switching) IEEE802.11 a and g: 54
Mbps max. data rate; IEEE802.11n: 300 Mbps
max. data rate
Active frequency • 802.11n: 2.4 GHz or 5 GHz
• 802.11b/g: 2400~2473 MHz
• 802.11a: 4900~5850 MHz
Typical operating distances • 802.11a: 40 ft. (12 m) @ 54 Mbps; 300 ft.
(91m)@6Mbps
• 802.11b: 100 ft. (30 m) @ 11 Mbps; 300 ft.
(91m)@1Mbps
• 802.11g: 100 ft. (30 m) @ 54 Mbps; 300 ft.
(91m)@1Mbps
• 802.11n: Estimated: double the operating
distance of 802.11g and 802.11a in their
respective frequencies
Number of channels • 802.11a: 8 independent channels
• 802.11b/g: 11 channels, 3 non-overlapping
channels
• 802.11n: Channel bonding takes two of
the non-overlapping 20MHz channels and
combines them into one 40MHz channel. It
is actually 12 non-overlapping channels with
channel bonding and 24 without. Also it is 1
non-overlapping channel in 2.4GHz when
channel bonding is used.
Security Encryption types: WEP, TKIP, AES, WPA 1.0
and WPA 2.0 compliant
Encryption key, lengths supported: 64 bits and
128 bits
Maximum recommended number of computers
to be connected over wireless LAN (during ad
hoc connection)
10 units or less
Fujitsu 79
Technical data
Rechargeable battery
For information on the batteries used in your device, please see
"http://solutions.us.fujitsu.com/www/content/support/contact/index.php".
Rechargeable
battery49Wh
Rechargeable
battery63Wh
Rechargeable battery
72 Wh
Rated voltage 10.8 V 10.8 V / 11.1 V 10.8 V / 11.25 V
Rated capacity 4500 mAh 5800 mAh / 5600 mAh 6700 mAh / 6400 mAh
AC adapter
Technicaldata
Electrical data
Primary
Rated voltage 100 V – 240 V (automatic)
Rated frequency 50 Hz – 60 Hz (automatic)
Secondary
Rated voltage 19 V
Max. rated current 3.42 A
An additional AC adapter or AC cable can be ordered at any time.
80 Fujitsu
Manufacturer’s notes
Manufacturer’s notes
Disposal and recycling
Notes
You can find information on this subject on your notebook or on our website
("http://solutions.us.fujitsu.com/www/content/products/trade-in_program/").
Recycling your battery
Over time, the batteries that run your mobile computer will begin to hold a charge for a
shorter amount of time; this is a natural occurrence for all batteries. When this occurs,
you may want to replace the battery with a fresh one*. If you replace it, it is important
that you dispose of the old battery properly because batteries contain materials that
could cause environmental damage if disposed of improperly.
Fujitsu is very concerned with environmental protection, and has enlisted the services of the
Rechargeable Battery Recycling Corporation (RBRC)**, a nonprofit public service organization
dedicated to protecting our environment by recycling old batteries at no cost to you.
RBRC has drop-off points at tens of thousands of locations throughout the United States and
Canada. To find the location nearest you, go to "www.RBRC.org" or call 1-800-822-8837.
If there are no convenient RBRC locations near you, you can also go to the EIA Consumer
Education Initiative website "http://EIAE.org/ " and search for a convenient disposal location.
Remember – protecting the environment is a cooperative effort, and we must
make every effort to protect it for current and future generations.
* To order a new battery for your Fujitsu mobile computer, go to the Fujitsu shopping site
at "www.shopfujitsu.com" in the US or "www.fujitsu.ca/products/notebooks" in Canada.
** RBRC is an independent third party to which Fujitsu provides funding for
battery recycling; RBRC is in no way affiliated with Fujitsu.
DOC (Industry CANADA) Notices
DOC(INDUSTRYCANADA)NOTICES
Radios and Television
This Class B digital apparatus meets all requirements of Canadian Interference-Causing Equipment
Regulations.
CET appareil numérique de la class B respecte toutes les exigence du Réglement
sur le matérial brouilleur du Canada.
Fujitsu 81
Manufacturer’s notes
UL Notice
IMPORTANT SAFETY INSTRUCTIONS
This unit requires an AC adapter to operate. Only use UL Listed I.T.E. adapters with an output rating
of 19 VDC, with a minimum current of 3.42A (65W). The correct output rating is indicated on the
AC adapter label. Refer to the illustration below for the correct AC Adapter output polarity:
When using your notebook equipment, basic safety precautions should always be followed to
reduce the risk of fire, electric shock and injury to persons, including the following:
• Do not use this product near water for example, near a bathtub, washbowl, kitchen
sink or laundry tub, in a wet basement or near a swimming pool.
• Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a
fire. They may explode. Check with local codes for possible special disposal instructions.
SAVE THESE INSTRUCTIONS
For Authorized Repair Technicians Only
CAUTION:
For continued protection against risk of fire, replace only with the
same type and rating fuse.
WARNING:
Danger of explosion if Lithium (CMOS) battery is incorrectly replaced. Replace only
with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instruction.
82 Fujitsu
Manufacturer’s notes
ENERGY STAR Compliance
Your Fujitsu system is an ENERGY STAR qualified mobile PC. By
choosing a computer with the latest energy-saving technology, you’re
helping to preserve our environment for future generations. ENERGY
STAR is a joint program of the U.S. Environmental Protection Agency,
U.S. Department of Energy, Natural Resources Canada, and other
governments around the world helping us save money while protecting
the environment through energy efficient products and practices. With
energy costs and global warming top-of-mind for consumers, Fujitsu is
committed to offering solutions that help consumers conserve energy
and improve the quality of our environment.
Sleep mode:
You will notice that your computer is initially set so that the display turns off after 15 minutes of
user inactivity, and the computer goes into Sleep mode after 20 minutes of user inactivity. When
going into Sleep mode, the computer also reduces the speed of any active Ethernet network
links. To “wake” the computer from Sleep mode, press the Suspend/Resume Button.
Energy saving benefits:
Fujitsu ENERGY STAR qualified mobile PCs use about half as much electricity as standard
equipment – saving half in utility costs. But more than that, ENERGY STAR also makes a difference
for the environment. Did you know that the average house can be responsible for twice the
greenhouse gas emissions as the average car? That’s because every time you flip on a light
switch, run your dishwasher, or turn on your PC, you use energy, which means more greenhouse
gas emissions from power plants. So the more energy we can save through energy efficiency,
the more we help to reduce greenhouse gases and the risks of global warming.
To learn more about the important ENERGY STAR program, visit:"www.energystar.gov".
To read about how Fujitsu is supporting Sustainable Management along with
several other environmental activities, visit the Fujitsu Corporate Citizenship page at:
"http://www.computers.us.fujitsu.com/www/content/aboutus/environmental/environment.php".
Declarations of conformity
Declarationsof conformity
This device complies with Part 15 of the FCC Rules. Operations are subject to the following two
conditions: (1) This device may not cause harmful interference, (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC and IC Regulatory Information
Please note the following regulatory information related to the wireless LAN
device.
Fujitsu 83
Manufacturer’s notes
Regulatory Notes and Statements
Wireless LAN, Health and Authorization for use
Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of
these emissions, however, are far much less than the electromagnetic energy emissions from wireless
devices such as mobile phones. Wireless LAN devices are safe for use by consumers because they
operate within the guidelines found in radio frequency safety standards and recommendations. The
use of Wireless LAN devices may be restricted in some situations or environments, such as:
• On board an airplane, or
• In an explosive environment, or
• In situations where the interference risk to other devices or services is
perceived or identified as harmful.
In cases in which the policy regarding use of Wireless LAN devices in specific environments is
not clear (e.g., airports, hospitals, chemical/oil/gas industrial plants, private buildings), obtain
authorization to use these devices prior to operating the equipment.
Regulatory Information/Disclaimers
Installation and use of this Wireless LAN device must be in strict accordance with the instructions
included in the user documentation provided with the product. Any changes or modifications made
to this device that are not expressly approved by the manufacturer may void the user’s authority to
operate the equipment. The manufacturer is not responsible for any radio or television interference
caused by unauthorized modification of this device, or the substitution or attachment of connecting
cables and equipment other than those specified by the manufacturer. It is the responsibility of the
user to correct any interference caused by such unauthorized modification, substitution or attachment.
The manufacturer and its authorized resellers or distributors will assume no liability for any damage
or violation of government regulations arising from failure to comply with these guidelines.
This device must not be co-located or operated in conjunction with any other antenna or transmitter.
For IEEE 802.11a Wireless LAN: For operation within 5.15~5.25 GHz frequency range, it is
restricted to indoor environments, and the antenna of this device must be integral.
Federal Communications Commission and Industry Canada statement:
This device complies with Part 15 of FCC Rules and Industry Canada license exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause
interference, and, (2) This device must accept any interference, including interference
that may cause undesired operation of this device.
Déclaration d’Industrie Canada
Cet appareil est conforme à la Section 15 des Règles de la FC C et à la ( aux) norme(s)
RSS concernant les appareils exempt s de licence par Industrie Canada. Son fonctionnement
est soumis aux deux condition s suivantes : (1) cet appareil ne doit pas causer d’interférence
nuisib le; (2) cet appareil doit accepter toutes les interférences reçues, y compris celles
pouvan t causer un mauvais fonctionnement de l’appareil.
84 Fujitsu
Manufacturer’s notes
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy. If not installed and used in accordance with
the instructions, it may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try and
correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the distance between the equipment and the receiver.
3. Connect the equipment to an outlet on a circuit different from the one the receiver is connected to.
4. Consult the dealer or an experienced radio/TV technician for help.
FCC Radio Frequency Exposure statement
The available scientific evidence does not show that any health problems are associated with
using low power wireless devices. There is no proof, however, that these low power wireless
devices are absolutely safe. Low power wireless devices emit low levels of radio frequency
energy (RF) in the microwave range while being used. Whereas high levels of RF can produce
health effects (by heating tissue), exposure to low-level RF that does not produce heating
effects causes no known adverse health effects. Many studies of low-level RF exposure have
not found any biological effects. Some studies have suggested that some biological effects
might occur, but such findings have not been confirmed by additional research.
The wireless LAN radio device has been tested and found to comply with FCC radiation
exposure limits set forth for an uncontrolled equipment and meets the FCC radio frequency
(RF) Exposure Guidelines in Supplement C to OET65.
The exposure standard for wireless devices employs a unit of measurement known as the Specific
Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg, and 1.6W/kg by Industry Canada.
This device is compliant with SAR for general population /uncontrolled exposure limits in
ANSI/IEEE C95.1-1992 and Canada RSS 102, and had been tested in accordance with
the measurement methods and procedures specified in OET Bulletin 65 Supplement C,
and Canada RSS 102. This device has been tested, and meets the FCC, IC RF exposure
guidelines when tested with the device operating conditions.
Déclaration de la FCC/d’Industrie Canada sur l’exposition
aux radiofréquences
La norme régissant l’exposition des appareils sans fil aux radiofréquences emploie une unité
de mesure dénommée Taux d’absorption spécifique, ou TAS. La FCC et Industrie Canada ont
défini la même limite de TAS : 1,6 W/kg. Cet appareil est conforme au TAS pour les limites
d’exposition générales de la population/non contrôlées définies par les règles C95.1-1992 de
l’ANSI/IEEE et RSS 102 d’Industrie Canada ; il a été testé en conformité avec les méthodes
et procédures de mesure spécifiées dans le supplément C du bulletin 65 de l’OET (Office
d’ingénierie et de technologie) et la règle RSS 102 d’Industrie Canada. Cet appareil a été testé
selon les directives de la FCC et d’IC concernant l’exposition aux radiofréquences et s’est révélé
conforme à ces dernières lorsqu’il a été testé en contact direct avec le corps.
Fujitsu 85
Manufacturer’s notes
Export restrictions
This product or software contains encryption code which may not be exported or transferred
from the US or Canada without an approved US Department of Commerce export license.
This device complies with Part 15 of FCC Rules., as well as ICES 003 B / NMB 003 B.
Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference
that may cause undesirable operation. Modifications not expressly authorized by Fujitsu
America, Inc. may invalidate the user’s right to operate this equipment.
Canadian Notice
The device for the 5150 - 5250 MHz band is only for indoor usage to reduce the potential
for harmful interference to co-channel mobile satellite systems.
The maximum antenna gain of 6 dBi permitted (for devices in the 5250 - 5350 MHz, 5470 - 5725
MHz and 5725 - 5825 MHz bands) to comply with the e.i.r.p. limit as stated in A9.2 of RSS210.
In addition, users are cautioned to take note that high power radars are allocated as primary
users (meaning they have priority) of 5250 - 5350 MHz and 5650 - 5850 MHz and these
radars could cause interference and/or damage to LE-LAN devices.
Avis pour le Canada
Le matériel destiné à un usage sur la bande 5 150 - 5 250 MHz doit être utilisé
uniquement à l’intérieur afin de réduire les risques de brouillage nuisible causé aux
systèmes mobiles par satellite fonctionnant sur un même canal.
Un gain d’antenne de 6 dBi est autorisé (pour le matériel utilisant les bandes 5 250 - 5 350
MHz, 5 470 - 5 725 MHz et 5 725 - 5 825 MHz), conformément à la limite p.i.r.e. maximale
permise selon l’annexe A9.2 afférent aux périphériques RSS210.
En outre, les utilisateurs doivent prendre garde au fait que les radars de grande puissance
sont considérés comme des utilisateurs principaux (ce qui signifie qu’ils sont prioritaires) des
bandes 5 250 - 5 350 MHz et 5 650 - 5 850 MHz et qu’ils pourraient causer des interférences
et/ou des dommages aux appareils de réseau exempts de licence.
86 Fujitsu
Appendix
Appendix
Before Using the Optional Wireless LAN
This manual describes the procedures required to properly set up and configure the optional
integrated Wireless LAN Mini-PCI device (referred to as "WLAN device" in the rest of the
manual). Before using the WLAN device, read this manual carefully to ensure its correct
operation. Keep this manual in a safe place for future reference.
Wireless LAN Devices Covered by this Document
This document is applicable to systems containing the following device:
• Intel Wireless-N 7260 802.11 BGN + BT v4.0 or
• Intel Dual Band Wireless AC 7260 + BT v4.0
Characteristics of the WLAN Device
• The WLAN devices are PCI Express Mini cards attached to the main board of the mobile computer.
• The WLAN devices operate in license-free RF bands, eliminating the need to procure
an FCC operating license. The WLAN operates in the 2.4GHz Industrial, Scientific,
and Medical (ISM) RF band and the lower, middle, and upper bands of the 5GHz
Unlicensed National Information Infrastructure (UNII) bands.
• The WLAN devices are capable of four operating modes, IEEE802.11a,
IEEE802.11b, IEEE802.11g, and IEEE802.11n.
• The WLAN device is Wi-Fi certified and operates (as applicable) at the maximum data
rate of 450 Mbps in IEEE802.11n mode (300 Mbps in this configuration); 54 Mbps
in IEEE802.11g mode; and 11 Mbps in IEEE802.11b mode.
• The WLAN devices support the following encryption methods - WEP,
TKIP, CKIP, and AES encryption.
• The Wireless LAN devices are compliant with the following standards: WPA,
WPA2, CCX1.0, CCX2.0, CCX3.0, and CCX4.0.
Wireless LAN Modes Using this Device
Ad Hoc Mode
"Ad Hoc Mode" refers to a wireless network architecture where wireless network connectivity
between multiple computers is established without a central wireless network device, typically
known as Access Point(s). Connectivity is accomplished using only client devices in a peer-to-peer
fashion. That is why Ad Hoc networks are also known as peer-to-peer networks. Ad Hoc
networks are an easy and inexpensive method for establishing network connectivity between
multiple computers. Ad Hoc mode requires that the SSID, network authentication, and encryption
key settings are identically configured on all computers in the Ad Hoc network.
Fujitsu 87
Appendix
Access Point (Infrastructure) Mode
Infrastructure mode refers to a wireless network architecture in which devices communicate with
wireless or wired network devices by communicating through an Access Point. In infrastructure
mode, wireless devices can communicate with each other or with a wired network. Corporate
wireless networks operate in infrastructure mode because they require access to the WLAN in
order to access services, devices, and computers (e.g., file servers, printers, databases).
88 Fujitsu
Appendix
**
*
* = An optional hub for a wired LAN may
be required depending upon the type
of access point used.
** = ADSL modem, cable modem, or similar
How to Handle This Device
The WLAN device is an optional device that may come pre-installed in your mobile computer. Under
normal circumstances, it should not be necessary for you to remove or re-install it. The Operating
System that your mobile computer comes with has been pre-configured to support the WLAN device.
• Integrated Intel Centrino wireless LAN devices support IEEE802.11a,
IEEE802.11b, IEEE802.11g, and IEEE802.11n.
• The WLAN device operates in the 2.4 GHz ISM band and the 5 GHz
lower, middle, and upper UNII bands.
• Microwave ovens may interfere with the operation of WLAN devices since they operate in the
same 2.4 GHz frequency range as IEEE802.11b/g/n devices. Interference by microwaves
does not occur with IEEE802.11a radio which operates in the 5 GHz RF band.
• Wireless devices that transmit in the 2.4 GHz range may interfere with operation of WLAN
devices in IEEE802.11b/g/n modes. Symptoms of interference include reduced throughput,
intermittent disconnects, and many frame errors. It is HIGHLY recommended that these
interfering devices be powered off to ensure proper operation of the WLAN device.
Fujitsu 89
Appendix
Deactivating/Disconnecting the WLAN Device
Disconnecting the WLAN device may be desired in certain circumstances (to extend battery
life) or where certain environments require it (i.e. hospitals, clinics, airplanes, etc.). The
WLAN device can be disconnected in Windows using the WLAN icon in the system tray
(Note that disconnecting via the icon in the system tray does not turn off the radio; it
continues to transmit and receive even though it’s not connected.)
►Press the button to start the WirelessSelector.
WirelessLANWirelessLANBluetoothBluetooth
The wireless component indicator will go off when the wireless components are switched off.
Configuring the Wireless LAN
The optional WLAN device can be configured to establish wireless network connectivity
using the software that is built into Windows. Support for most industry standard
security solutions is contained in this software.
Pre-defined parameters will be required for this procedure. Please consult with
your network administrator for these parameters:
Configuring the WLAN Using Windows
The WLAN device can be configured to establish wireless network connectivity using
the software that is built into Windows Vista. Support for most industry standard
security solutions is contained in this software.
Pre-defined parameters are required for this procedure. Consult your network
administrator for these parameters:
1. From the Modern Start screen, press Windows +X, then select Control Panel from the menu.
2. If the Control Panel is not in Classic View, select Classic View from the left panel.
Double-click the Network and Sharing Center icon.
3. Select Setup a new connection or network.
4. Depending upon what type of connection you would like to make, make a selection. For
an infrastructure network, select Manually connect to a wireless network.
5. Enter the required information. It may be necessary to consult with your network
administrator for some of the information.
6. In the event you require assistance, go to the Network and Sharing Center window (Control
Panel > Network and Sharing Center), and type in relevant keywords in the Search box.
Connection to the network
After you have configured your computer, you can connect to an active network
by performing the following steps:
1. Click on the WLAN icon in the system tray.
2. Select Connect to a network.
3. Select a network from the list that appears, and click the Connect button.
90 Fujitsu
Appendix
Troubleshooting the WLAN
Causes and countermeasures for troubles you may encounter while using your
wireless LAN are described in the following table.
Problem Possible Cause Possible Solution
Incorrect network name (SSID)
or network key
Ad hoc connection: verify that
the network names (SSID’s)
and network keys (WEP) of
all computers to be connected
have been configured correctly.
SSID’s and WEP key values
must be identical on each
machine.
Access Point (Infrastructure)
connection: set the network
name (SSID) and network key
to the same values as those of
the access point.
Set the Network Authentication
value identically to that of the
Access Point. Please consult
your network administrator for
this value, if necessary.
Unavailable network connection
Weak received signal strength
and/or link quality
Ad hoc connection: Retry
connection after shortening
the distance to the destination
computer or removing any
obstacles for better sight.
Access Point (Infrastructure)
connection: Retry connection
after shortening the distance to
the access point or removing
any obstacles for better sight.
Fujitsu 91
Appendix
Problem Possible Cause Possible Solution
The WLAN device was
deactivated or is disabled
Check if the wireless switch
is turned On. Go to Start >
Control Panel, and doubleclick
on Windows Mobility Center.If
the wireless network is off, click
the Turn wireless on button.
The computer to be connected
is turned off
Check if the computer to be
connected is turned ON.
Incorrectly configured network
settings
Recheck the configuration of
your network settings.
RF interference from Access
Points or other wireless
networks
The use of identical or
overlapping RF channelscan
cause interference with the
operation of the WLAN device.
Change the channel of your
Access Point to a channel
that does not overlap with the
interfering device.
Wireless network authentication
has failed
Re-check your Network
Authentication, Encryption,
and Security settings.
Incorrectly configured
security settings such as
an incorrectly typed WEP
key, a mis-configured LEAP
username, or anincorrectly
chosen authentication method
will cause theLANdeviceto
associate but not authenticate
to the wireless network.
Unavailable network connection
(continued)
Incorrect IP address
configuration
This only applies to networks
using static IP addresses.
Please contact your network
administrator for the correct
settings.
92 Fujitsu
Appendix
Using the Bluetooth Device
Bluetooth is integrated into the Wireless LAN module. The Bluetooth capabilities are Bluetooth
Basic, EDR and Bluetooth Low Energy (BT v4.0) operational modes.
What is Bluetooth?
Bluetooth technology is designed as a short-range wireless link between mobile devices, such
as laptop computers, phones, printers, and cameras. Bluetooth technology is used to create
Personal Area Networks (PANs) between devices in short-range of each other.
Proceed as follows to individually enable or disable wireless LAN or Bluetooth devices:
1. Switch on the WLAN/Bluetooth using the button.
2. In the screen Modern Start, select the option Charms > Settings
> Change PC Settings > Wireless.
3. Under Wireless > Wireless Devices, click on the switch Bluetooth to switch on Bluetooth.
Where to Find Information About Bluetooth
For additional information about Bluetooth Technology, visit the Bluetooth
Web site at: "www.bluetooth.com".
FCC Radiation Exposure Statement
This system complies with the FCC limit values for radio frequency radiation in an uncontrolled
environment. The Bluetooth antenna is located at the top edge of the LCD screen and is exempt
from the criteria for minimum distance because of its low power consumption.
The transmitter used in this system must not be operated together with other antennas or transmitters.
Canadian Notice
To prevent radio interference to licensed services, this system is designed for use in indoor spaces
/ in buildings and not directly at window openings, to allow a maximum shielding.
Warranty
Users are not authorized to modify this product. Any modifications invalidate the warranty.
This equipment may not be modified, altered, or changed in any way without signed
written permission from Fujitsu. Unauthorized modification will void the equipment
authorization from the FCC and Industry Canada and the warranty.
Image Backup and Recovery Procedures
Thank you for purchasing a Fujitsu computer. Fujitsu is committed to bringing you
the best computing experience with your new system.
It is very important that you create DVD copies of your Recovery Image and Bootable Disk
before beginning to use your system. To do so, follow the instructions in the “Creating a
Backup of Bootable Disk and Recovery Image” section of this document.
It is also important that you create a copy of the software that is essential for your system to access the
internet (hereafter called “essential access software”) to external writable media or an external drive.
To do so, follow the instructions in the “Creating a Backup of the System-Specific Software Drivers”.
Fujitsu 93
Appendix
Creating a Backup of Bootable Disk and Recovery Image
When you purchased your new system, a copy of the recovery image was loaded into a
hidden partition on your hard disk drive. Having a copy of the recovery image available to
you means that in the event of system failure, you will be able to restore it and re-install
the essential access software using Fujitsu Software Auto Installer.
To make a copy of the recovery image to DVD disks, you will need three or four blank
disks to create the copy. After creating the copy, be sure to label the disks and keep
them in a safe place to ensure they do not get damaged.
Note: If your system does not have an internal writable DVD drive, connect your
system to an external drive* before beginning the following steps.
1. Launch System Restore and Recovery from the desktop icon. It will allow you to create
the Bootable Disk and the Recovery Image Disk Set.
2. On “Step 1: Select the Bootable Disk from the list”:
a. Select a media type.
b. Notice the number of disks that are needed for the set.
c. Click Next to proceed.
3. On “Step 2: Confirm your Recovery Disk”, click Next.
4. On “Step 3:” follow the on-screen instructions to make the disk or disk set, then click
Start. It takes approximately 20 minutes to make one disk.
5. On “Step 4”, when the disk creation is completed, a message appears.
Click Finish to exit the program.
6. Repeat Step 1: Select Recovery Disk from the list and repeat the above
steps 2(a), 2(b), 2(c), 3, 4 and 5.
* DEPENDING UPON YOUR OPTICAL DRIVE AND MEDIA FORMAT USED, SOME MEDIA
TYPES MAY BE INCOMPATIBLE FOR CREATING IMAGE BACKUPS.
94 Fujitsu
Appendix
Creating a Backup of Essential Access Software
When you purchased your new system, a “Fujitsu Software Extractor” shortcut was loaded to
“C:\Fujitsu\Drivers\AutoInstaller\”. This shortcut allows you to save the software driver packages
along with the extracted Auto Installer software package to a selected location. It is recommended
that you save these packages to writable media or an external drive. This ensures that in the
event of system failure you will be able to re-install the essential access software.
1. Open the C:\Fujitsu\Drivers\AutoInstaller\ folder
2. Run “Fujitsu Software Extractor” as an Administrator
a. Right-click on Fujitsu Software Extractor.
b. Select the “Run as Administrator” option from the menu that is displayed.
3. The default save location is C:\Fujitsu\ AutoInstaller\ Drivers\. You can change the location
by clicking on the Browse button and selecting your preferred location.
Note: It is recommended that you change the default location and save the
software packages to the external writable media or drive.
4. Click on the Save Packages button.
5. Fujitsu Software Extractor copies the zipped software packages and Readme files,
and extracts the Auto Installer folder to the selected location.
Note: The extracted Auto Installer will later be used to install the software
automatically on the system in the event of generic image restoration when
the software is not pre-installed in the image.
RECOVERYOURSY
STEM WHEN THE HARD
DRIVE IS STILL ACCESSIBLE
Using the Recovery and Utility Tools
The Recovery and Utility tools consist of a variety of tools that will help you recover your
recovery image and system images, and delete the data from your hard disk.
Methods for accessing the utilities
Recovery and Utility Tools are preinstalled in a hidden partition by the factory, or
they can be accessed by using the bootable disk.
Note: The Recovery and Utility tools may be deleted from your hard disk
drive if you modify the partitions. If that occurs, you will not be able to
use the hidden partition for booting to Recovery and Utility Tools, but you
will still be able to boot from the Bootable Disk.
Fujitsu 95
Appendix
Determining whether Recovery and Utility is pre-loaded
1. Turn on or reboot your system. When the Fujitsu logo appears, press the F12 key.
2. Use the Tab key to get to the Application Menu.
3. Check whether the Recovery and Utility option is present. If it is not present, it means
that the utility must be used from the Bootable Disk. Proceed to “Running Recovery and
Utility from the Bootable Disk” if Recovery and Utility is unavailable.
Running Recovery and Utility from hard disk
1. Turn on or reboot your system. When the Fujitsu logo appears, press the F12 key.
2. Use the Tab key to get to the Application Menu.
3. Cursor down to Recovery and Utility and press the Enter key.
4. Choose your language, if necessary. Select Recovery and Utility to proceed.
5. Three tool options appear: Diagnostics,Recovery,andUtility (refer to the Recovery and
Utility tools section below for instructions on how to use these tools).
6. If this was successful please skip the next step and go to “Recovery and Utility tools.”
7. If this was NOT successful, please go to the next step.
Running Recovery and Utility from the Bootable disk
To verify/change the boot-up priority (rather than booting-up from the hard drive or
an external media drive), perform the following steps:
1. Power on your system. When the Fujitsu logo appears on the screen, press the F12 key.
2. Insert the bootable disk into the drive tray.
3. Highlight the CD/DVD option from the Boot menu, then press Enter .
4. Click OK.
5. Select CD/DVD boot mode: UEFI Mode, if applicable, and then press Enter .
While the files are being loaded from the disk, the Fujitsu logo screen will appear
followed by a progress bar at the bottom of the screen.
96 Fujitsu
Appendix
Recovery and Utility tools
Note: Recovery and Utility tools may not be available on your system depending
on the region from which the system was shipped.
Diagnostics tool: The Diagnostics tool is designed for use by IT professionals. It is not likely you
will need to use this tool. If you should need to use this tool, perform the following steps:
1. Press the Diagnostics Tool button to start the Diagnostics tool.
2. Read the note, and then click OK.
3. Choose one or more of the following options for diagnostics on the Fujitsu Hardware Diagnostics
Tool window: CPU, Memory, Display, Hard Disk, CD/DVD/BD, Floppy Disk, Keyboard, and Mouse.
4. Click the Option button in the Tool menu to specify how many times the tool
should run diagnostics on each selected component.
5. Press Execute to start the Diagnostics tool.
6. After the execution is completed, the selected components are circled in red to indicate that they
have been diagnosed and the result dialog window opens. Click Close to close the window.
7. Click End to close the Diagnostics tool, and then click Ye s to confirm the end of diagnostics session.
Recovery tool: The Recovery tool contains two options:
• Restore C Drive: Restore recovery image (only C: drive)
• Restore Full Hard Drive: Restore recovery image (full hard drive).
You can use these tools to restore the Recovery Image from the hidden partition, and perform a full
hard drive recovery. Please refer to instructions above for details on how to create a Recovery Image.
Restore the Recovery Image from Hidden Partition
1. Click [Restore C: drive] from Recovery and Utility tools
2. The progress bar is followed by “Restore Recovery image (only C: drive)” screen
confirming that the Image will be restored to the C: drive. Click Next.
3. Read the instruction screen and select Agree,thenclickNext.
4. Click OK to acknowledge the warning message to restore recovery image to the C: drive.
5. When the progress bar appears, wait for the process to complete.
6. Click Finish when the process completes; the computer will restart to Windows.
7. Follow the steps listed in the “Auto Installation support for software packages
from hidden partition” section.
8. Download FSDM (Fujitsu Software Download Manager) from the support site and download
all the software applicable to the model and OS using FSDM.
9. Follow the steps listed in “Auto Installation support for software packages
downloaded from support website” section.
Fujitsu 97
Appendix
RECOVER YOUR SYSTEM WHEN THE HARD
DRIVE IS NOT BOOTABLE
Restore the Recovery Image for Full Hard Drive
Follow the steps in the “Recovering your Recovery Image using Recovery and
Utility (for new hard drive or non-bootable hard drive)” section. You will need the
Bootable Disk and the Recovery Disk Set for this task.
Utility tool: If applicable for your region, the Utility tool contains two options:
Hard Disk Data Delete and Partition Creation.
The Hard Disk Data Delete utility is used to delete all data on the hard disk
and prevent the data from being reused.
NOTE: Do not use the Hard Disk Data Delete utility unless you are absolutely certain
that you want to erase your entire hard disk, including all partitions.
To delete hard disk data:
1. Click the Hard Disk Data Delete button. The progress bar appears, followed by the EULA screen.
2. Agree to the EULA and click Next.
3. Choose the hard disk from which the data should be deleted in the list of hard disks and click Next.
The Partition Creation utility is used to change the C: and D: drive partition sizes.
To run this utility: (This is not an option when using Windows 7.)
1. Click the Partition Creation button.
2. A progress bar appears, followed by the EULA screen. Agree to the EULA.
3. On the Recovery Tool - Partition Creation screen, move the slider to set disk size, and then click OK.
4. Click Yes in the Partition Creation confirmation dialog.
WARNING: It is highly recommended that you send your product to Fujitsu
Service to replace a hard drive. A mistake could possibly destroy your
computer, your new hard drive or both.
98 Fujitsu
Appendix
Recovering Your Recovery Image Using Recovery and Utility
(for new hard drive or non-bootable hard drive)
If you have installed a new hard drive or your hard drive is not bootable, perform the following steps.
Note: You will need the Bootable disk and Recovery Image disk set for this recovery.
1. Power on your system. When the Fujitsu logo appears on the screen, press the Enter key.
2. Insert the bootable disk in your DVD drive, then click OK.
3. Highlight the CD/DVD option from the Boot Menu and press Enter .
4. Select CD/DVD boot mode: Select UEFI Mode, if applicable and press Enter .
While the files are being loaded from the disk, the Fujitsu logo screen appears
followed by a progress bar at the bottom of the screen.
5. Choose your language, if necessary.
6. Three tool options appear: Diagnostics,Recovery and Utility. Select Recovery.
• For Windows 8.1: Select Restore full hard drive
• For Windows 7: Select Restoring the Factory Image (full hard drive recovery)
7. Click Next to confirm full hard drive restoration. All data on HDD will be deleted.
8. Agree to EULA by selecting Agree option and clicking Next.
9. Click Next on the Recovery Disk Check screen to verify that the bootable
disk has been inserted into the optical drive.
10. The Checking for Recovery Disk screen appears followed by the prompt to insert the
first disk. Click OK to continue. Repeat this step for all disks. After all recovery disks
have been checked and the check has been completed, click Next.
11. Follow the prompt to reinsert the first recovery disk and click Next.
12. Click OK when you receive the final warning informing you that all data on drive
C will be lost. This starts the recovery process.
13. Follow the prompts to insert the next recovery disks and click OK.
14. After the copying of the image to the HDD completes the restore process is
complete, click Finish to restart the system. The computer will restart automatically
and then go through the firstbootprocess.
15. Follow the steps listed in “Auto Installation support for essential access
software from backup location” section.
16. Download FSDM (Fujitsu Software Download Manager) from support site and download
all the software applicable to the model and OS using FSDM.
17. Follow the steps listed in “Auto Installation support for essential access
software downloaded from support website.
Fujitsu 99
Appendix
Installing the Software after the Recovery Image is Restored
Auto-installation support for essential access software
from hidden partition
The below listed steps are applicable only in cases in which the recovery image restore
and hidden partition contents have not been wiped out.
1. After the recovery image is restored, launch the desktop icon “Fujitsu Software Auto Installer”.
2. Double-click on “Fujitsu Software Auto Installer” desktop icon.
3. Click Yes on User Account Control Dialog box. This will take some time to
process the software packages. A message will be displayed during this time,
“Please wait while the content is being processed”.
4. If EULA is displayed for Fujitsu Software Auto Installer, accept the EULA, otherwise continue.
5. Then Fujitsu Software Auto Installer user interface will be launched providing ability
to auto-install the essential access software on the system.
6. It is recommended that you install all the software in the listed order. You can
Select All, to install the software in the order listed.
7. Click Install to start the installation.
8. After installing all the selected drivers, Installation Results window will be displayed. Click OK.
9. “You must restart the system for the settings to take effect. Do you wish to
reboot now?” message appears. Select Yes.
10. The system will now reboot.
11. You can now connect to the internet and download FSDM (Fujitsu Software Download
Manager) from the support site and download all the software applicable to the
model and OS using FSDM if they are not downloaded yet.
100 Fujitsu
Appendix
Auto-installation support for essential access software
from backup location
The below listed steps are applicable in cases in which a backup copy was created as
mentioned in the section “Creating a Backup of essential access software”.
1. It is important to have the extracted Auto installer software package folder
and Readme file in the same location as other software folders. Otherwise
auto-installation of the software will not be supported.
2. Inside the Auto Installer software package, launch FjAutoinstall.exe as an Administrator.
3. Click Ye s on the User Account Control dialog box. This will take some time to
process the software packages. A message will be displayed during this time stating,
“Please wait while the content is being processed”.
4. If EULA is displayed for Fujitsu Software Auto Installer, accept the EULA, otherwise continue.
5. The Fujitsu Software Auto Installer user interface will be launched providing ability
to auto install the essential access software on the system.
6. It is recommended that you install all the software in the listed order. You can
“Select All”, to install the software in the order listed.
7. Click the Install button to start the installation.
8. After installing all the selected drivers, Installation Results window is be displayed. Click OK.
9. “You must restart the system for the settings to take effect. Do you wish to
reboot now?” message appears. Select Ye s.
10. The system will now reboot.
Auto Installation support for the software downloaded from support website
1. Download FSDM (Fujitsu Software Download Manager) from the support site and download all
the drivers applicable to the model and OS using FSDM if they are not downloaded yet.
2. When the software packages are downloaded from web, it is important to download
the Auto Installer Software package and the model/language- specific Readme
file if you prefer to auto install the software.
3. It is important to have the extracted Auto Installer software package folder
and Readme file in the same location as other software folders. Otherwise
auto-installation of the software will not be supported.
4. Inside the Auto Installer software package, launch FjAutoinstall.exe as administrator.
5. Click Ye s on the User Account Control dialog box. This will take some time to
process the software packages. A message will be displayed during this time stating
“Please wait while the content is being processed”.
6. If EULA is displayed for Fujitsu Software Auto Installer, accept the EULA, otherwise continue.
7. The Fujitsu Software Auto Installer user interface will be launched providing the ability
to auto install the software downloaded from support site.
8. It is recommended that you install all the software in the listed order. You can
Select All, to install the software in the order listed.
9. Click the Install button to start the installation.
10. After installing all the selected drivers, the Installation Results window is displayed. Click OK.
11. “You must restart the system for the settings to take effect. Do you wish to
reboot now?” message appears. Select Ye s.
12. The system will now reboot.
Fujitsu 101
Appendix
Downloading Driver Updates
To ensure that you always have the most current driver updates related to your system,
you should occasionally access the Fujitsu Software Download Manager (FSDM) utility.
The FSDM utility is available from the Fujitsu Support site. FSDM will allow you to view
and download a list of the most current drivers, utilities, and applications to determine
whether you have the latest versions. To download the FSDM Utility, go to the Support Site:
"http://support.fujitsupc.com/CS/Portal/support.do?srch=DOWNLOADS".
If you are planning on downgrading, upgrading or changing versions of your operating system during
this process please see the User’s Guide for more information at "http://solutions.us.fujitsu.com".
102 Fujitsu
Index
Index
A
A beep sounds every second 72
AC adapter
connecting 18
Set up 18
Acoustic warnings 75
Alt+Tab 27
Anti-theft protection 49
Application keys 28
Audio connections 60
B
Back tab 27
Backspace 24
Backspace key 24
Battery 32
battery charge 40
Caring for and maintaining 32
charge level 32
Charging 32
see Rechargeable battery 32
Self-discharge 32
Service life 32
Storing 32
battery charge meter 32
Battery indicator 21
Battery status indicator
see Battery indicator 21
Battery symbol
see Battery indicator 21
BIOS Setup Utility
, protecting with password 50
calling 69
exiting 70
operation 69
Settings 69
Blank LCD screen 72
Bluetooth
switching module off 90
switching module on 90
Bluetooth, Safety notes 14
Boards 61
Bonus Apps 19
Brightness of the screen
Decrease 27
Increase 27
C
Caps Lock 24
Indicator 21
Caps Lock key 24
CD/DVD
Manual emergency removal 38
CD/DVD indicator 37
Charge capacity, battery 32
Charging back-up battery 72
Choose a location 18
Cleaning 16
Components
Installing/Removing 61
Configuration, BIOS Setup Utility 69
Configuring hardware 69
Configuring system 69
Connecting audio devices 60
Connecting headphones 60
Connecting microphone 60
Crystal View screen
cleaning 16
Ctrl+Alt+Del 27
Cursor control 24
Cursor keys 24
D
Date not correct 72
Declarations of conformity 83
Device drivers
serial port 56
Devices,
connecting 56
DOC (INDUSTRY CANADA) NOTICES 81
Drive
Removing 35
Drive indicator
Indicator 21
E
Emergency removal of optical disk 38
Ending
energy saving mode 74
Energy
Energy consumption 40
Energy saving 14
Energy saving functions 40
Enter 24
Enter key 24
Error messages on the screen 76
Errors
Acoustic warnings 75
Screen messages 76
ESD 61
Fujitsu 103
Index
Ethernet LAN 43
External devices,
connecting 56
F
Fault
Elimination 71
Fingerprint sensor 48
configuring 48
First-time setup 17
Fn key 24
Fn+F10 27
Fn+F3 26
Fn+F4 26
Fn+F6 27
Fn+F7 27
Fn+F8 27
Fn+F9 27
G
Getting started 17
I
Important notes 13
In case of service 61
Incorrect time 72
Indicator
Caps Lock 21
Drive 21
Num Lock 21
Scroll Lock 21
Information,
safety 13
Instructions
Boards 61
Cleaning 16
K
Kensington Lock Cable 49
Key combinations 26
Keyboard 23
cleaning 16
keys 23
L
LCD screen
cleaning 16
Decrease brightness 27
difficult to read 72
Notes 30
reflected glare 72
Remains blank 72
Line feed 24
M
Main memory
see memory expansion 62
Making ready to use 18
Manual removal of optical disk 38
Mechanical security 49
Memory card
handling 41
inserting 41
removing 41
Memory expansion
installing 64
removing 63
Memory module
Important notes 62
installing 64
removing 63
Memory removal
see memory expansion 62
Microphone 42
Mobile operation 14
Modular bay 35
Modular bay device
Removing 35
Modular bay devices 35
Monitor
connecting 55
no image 73
remains blank 73
unstable image 73
Monitor port
see VGA socket 55
N
Notebook
before traveling 15
cleaning 16
does not start 74
not working 74
operating 20
switching off 22
transporting 14, 16
Notes 13
disposal / recycling 81
Energy saving 14
LCD screen 30
Transport 14
104 Fujitsu
Index
Num Lock
indicator 25–26
Indicator 21
Number keypad 23
Numeric keypad 23
see Separate number keypad 26
see Virtual number keys 25
O
Operating system
activating system protection 51
cancel system protection 51
Protecting with password 51
Operation, notebook 20
Optical disk
Inserting 37
Removing 37
Optical disks
Handling 36
Optical drive 36
P
Packaging 17
Password
changing 50
entering 50
removing 51
Password protection 49
Port replicator
Connecting a notebook 45
Ports 44
Ports
Port replicator 44
Power saving 14
Power-on indicator 21
Printer does not print 74
Problem solving 71
R
Rechargeable battery
see battery 32
Return 24
S
Safety information 13
Scroll Lock
Indicator 21
Security functions 48
Smart Card 53
SystemLock 53
Self-discharge, battery 32
Separate number keypad 26
serial port
connecting devices 56
Serial port
Settings 56
Serial port, 56
Service life, battery 32
Set up
Device 18
Setup
see BIOS Setup Utility 69
Shift 24
Shift key 24
Shift+Tab 27
Slot
Memory cards 41
Speaker 42
switch off 26
switch on 26
Standby indicator 21
Status indicators 20
Subwoofer 42
Summer time 72
Supervisor password
change 50
entering 50
removing 51
Switching between display outputs 27
Switching on
the notebook 22
Switchingonforthefirst time 19
System expansion 62
see memory expansion 62
System settings, BIOS Setup Utility 69
T
Tab key 24
Technical data 78
AC adapter 80
notebook 78
The wireless connection to a network
does not work 75
Time not correct 72
Tips 71
Touchpad 26, 29
buttons 29
cleaning 16
dragging items 30
executing commands 29
Move pointer 29
selectinganitem 29
switch off 26
Touchpad buttons 26
Fujitsu 105
Index
TPM 52
Transport 14, 16
Damage during transportation 17
Traveling, notebook 15
Troubleshooting 71
Trusted Platform Module 52
U
USB charging function 58
USB ports 57
User password
change 50
entering 50
removing 51
Using the security lock 49
V
VGA socket 55
Virtual number keys 25
Volume
increase 27
reduce 27
Volume control 42
W
Webcam 31
Weight saver
Removing 35
Windows key 24
Winter time 72
wireless components
Safety notes 14
Wireless LAN
Safety notes 14
switching module off 90
switching module on 90
Wrong date/time 72
106 Fujitsu