Table of Contents
- FUJITSU LIFEBOOK E546 / FUJITSU LIFEBOOK E556
- Contents
- Innovative technology
- Ports and controls
- Important notes
- First-time setup of your device
- Working with the notebook
- Status indicators
- Switching on the notebook
- Notebook: switching off
- Keyboard
- Application keys
- Touchpad and touchpad buttons
- LCD screen
- Webcam
- Rechargeable battery
- Module
- Optical drive
- Removing and fitting the dust removal cover (ventilation slot cover)
- Using the power-management features
- Memory cards
- Loudspeakers and microphones
- SIM card
- Wireless LAN/Bluetooth/UMTS/LTE radio components
- Ethernet and LAN
- Your Port Replicator
- Security functions
- Connecting external devices
- Removing and installing components during servicing
- Settings in BIOS Setup Utility
- Starting the BIOS Setup Utility
- Operating BIOS Setup Utility
- Exiting BIOS Setup Utility
- Exit Saving Changes - save changes and exit BIOS Setup Utility
- Exit Discarding Changes – Discard changes and exit BIOS Setup Utility
- Load Setup Defaults – Copy Standard Entries
- Discard Changes – Discard changes without exiting the BIOS Setup Utility
- Save Changes - save changes without exiting the BIOS Setup Utility
- Save Changes and Power Off
- Troubleshooting and tips
- Help if problems occur
- Restoring the hard disk contents under Windows
- The notebook's date or time is incorrect
- When certain characters are entered on the keyboard, only numerals are written
- The notebook’s LCD screen remains blank
- The LCD screen is difficult to read
- The external monitor remains blank
- The external monitor is blank or the image is unstable
- The notebook cannot be started
- The notebook stops working
- The printer does not print
- The radio connection to a network does not work
- Acoustic warnings
- SmartCard reader is not recognised.
- SmartCard PIN forgotten
- SmartCard lost
- Error messages on the screen
- Technical data
- Manufacturer’s notes
- Index
Fujitsu E546 User Manual
Displayed below is the user manual for E546 by Fujitsu which is a product in the Notebooks category. This manual has pages.
Related Manuals
System
Operating Manual
FUJITSU LIFEBOOK E546
FUJITSU LIFEBOOK E556
Congratulations on your purchase of an innovative
product from Fujitsu.
The latest information about our products, tips, updates etc. can be found
on the Internet at: "http://www.fujitsu.com/fts/"
You can find driver updates at: "http://support.ts.fujitsu.com/download"
Should you have any technical questions, please contact:
• our Hotline/Service Desk (see the Service Desk list or visit:
"http://support.ts.fujitsu.com/contact/servicedesk")
• Your sales partner
• Your sales office
We hope you enjoy working with your new Fujitsu system!
FUJITSU LIFEBOOK E546
FUJITSU LIFEBOOK E556
Operating Manual
Innovative technology 7
Ports and controls 9
Important notes 13
First-time setup of your device 16
Working with the notebook 19
Security functions 51
Connecting external devices 57
Removing and installing components
during servicing 64
Settings in BIOS Setup Utility 72
Troubleshooting and tips 75
Technical data 83
Manufacturer’s notes 85
Index 87
Remarks
Information on the product description meets the design specifications of Fujitsu and
is provided for comparison purposes. Several factors may cause the actual results to
differ. Technical data is subject to change without prior notification. Fujitsu rejects any
responsibility with regard to technical or editorial mistakes or omissions.
Trademarks
Fujitsu, the Fujitsu logo and LIFEBOOK are registered trademarks of Fujitsu Limited
or its subsidiaries in the United States and other countries.
Microsoft and Windows are trademarks or registered trademarks of the Microsoft
Corporation in the United States and/or other countries.
Adobe Reader is a trademark of Adobe Systems Incorporated.
All other trademarks specified here are the property of their respective owners.
Copyright
No part of this publication may be copied, reproduced or translated without
the prior written consent of Fujitsu.
No part of this publication may be saved or transferred by any electronic means
without the written approval of Fujitsu.
Contents
Contents
Innovative technology ................................................................. 7
Furtherinformation ...................................................................... 7
Notational conventions .................................................................. 8
Ports and controls ..................................................................... 9
Importantnotes ........................................................................ 13
Safetynotes ............................................................................ 13
Additional safety notes for devices with radio components . . . . . ............................. 13
Energysaving .......................................................................... 14
Energy saving under Windows ....................................................... 14
Travelling withyournotebook ............................................................ 14
Beforeyoutravel ................................................................... 14
Notebook: transporting ............................................................... 15
Cleaningthenotebook .................................................................. 15
First-time setup ofyour device ......................................................... 16
Unpacking and checking the device ...................................................... 16
Selectingalocat
ion ..................................................................... 17
Mains adapter connecting ............................................................... 17
Switchingonthedevice for the first time .................................................. 18
Working with the notebook ............................................................ 19
Statusindicators ........................................................................ 19
Switching on the notebook . . . . ........................................................... 21
Notebook: switching off .................................................................. 21
Keyboard ............................................................................... 22
Virtualnumerickeypad .............................................................. 24
Separate number block . . . ........................................................... 25
Key combinations ................................................................... 25
Country and keyboard settings ....................................................... 27
Application keys ........................................................................ 27
Touchpadandtouchpad buttons .......................................................... 28
Movingthepointer .................................................................. 28
Selecting an item .................................................................... 28
Executing commands . . . . . ........................................................... 28
Dragging items ...................................................................... 29
LCDscreen ............................................................................ 29
Webcam ............................................................................... 30
Rechargeablebattery ................................................................... 31
Charging, caringforandmaintaining the battery ....................................... 31
Removingandinstallingthebattery ................................................... 31
Module ................................................................................. 34
Removing a module . . . . . . ........................................................... 34
Installing a module .................................................................. 35
Opticaldrive ............................................................................ 35
Handlingdata carriers ............................................................... 35
CD/DVD indicator ................................................................... 36
Inserting or removing adata carrier ................................................... 36
Manual removal (emergency removal) . . . . ............................................ 37
Removing and fittingthedustremovalcover (ventilation slotcover) ......................... 37
Using the power-management features ................................................... 39
Fujitsu 3
Contents
Memory cards .......................................................................... 40
Supported formats .................................................................. 40
Inserting the memorycard ........................................................... 40
Removingthememorycard .......................................................... 40
Loudspeakers and microphones . . ........................................................ 41
SIM card ............................................................................... 42
Inserting the SIM card ............................................................... 42
RemovingtheSIMcard .............................................................. 44
Wireless LAN/Bluetooth/UMTS/LTE radio components . . . .................................. 45
Switching the wireless components on and off ......................................... 45
SettingupWLAN access ............................................................ 45
AccessviaUMTS/LTE ............................................................... 46
EthernetandLAN ....................................................................... 46
YourPort Replicator ..................................................................... 47
Ports on thePortReplicator .......................................................... 47
Connecting the notebook to the Port Replicator . . . . . .................................. 48
Connecting the mains adapter to the Port Replicator . .................................. 49
Switching on the notebook via the port replicator . . . . . .................................. 49
Disconnecting the notebook from the Port Replicator .................................. 50
Securityfunctions ..................................................................... 51
Configuring the fingerprint sensor ........................................................ 51
Using theSecurity Lock ................................................................. 52
Configuring password protection in BIOSSetupUtility ...................................... 52
Protecting BIOS Setup Utility (supervisor and user password) . .......................... 53
Password protection for booting of the operating system . .............................. 54
Passwordprotectionfortheharddisk ................................................. 54
Trusted Platform Module (TPM) (device-dependent) . . . . . .................................. 55
EnablingTPM ....................................................................... 55
Disabling TPM ...................................................................... 55
SmartCard reader ....................................................................... 56
Inserting the SmartCard ............................................................. 56
Connecting externaldevices ........................................................... 57
Connecting an external monitor . . ........................................................ 58
Connecting external devices to the serial port (optional) . . .................................. 59
Port settings ........................................................................ 59
Devicedrivers ...................................................................... 59
Connecting USB devices ................................................................ 60
USBport withcharging function (Anytime USBcharge) ................................. 61
Connecting an external SATA hard disk (eSATA) (port replicator only) . ................... 62
Safe removalofeSATA and USB devices ............................................. 62
Connecting external audio devices . . . . . . ................................................. 63
Microphone port/Line In . . ............................................................ 63
Headphone port . . . . . ................................................................ 63
Removing and installing components during servicing . . . .............................. 64
Notes on installing and removing boards and components .................................. 64
Preparing to remove components ........................................................ 65
Installingand removing memoryexpansion ................................................ 65
Removinga cover ................................................................... 66
Removing memory modules . . ........................................................ 66
Installinga memorymodule .......................................................... 67
Attaching the cover .................................................................. 67
4Fujitsu
Contents
Removingandinstallingtheharddisk .................................................... 68
Removingacover ................................................................... 68
Removingaharddisk ............................................................... 69
Installinga hard disk ................................................................. 70
Attaching the cover .................................................................. 71
Finishing component removal . ........................................................... 71
Settings in BIOS Setup Utility . . . ....................................................... 72
StartingtheBIOSSetup Utility ........................................................... 72
OperatingBIOSSetup Utility ............................................................. 73
ExitingBIOSSetupUtility ................................................................ 74
Exit Saving Changes - save changes and exit BIOS Setup Utility . . ..................... 74
Exit Discarding Changes – Discard changes and exit BIOS Setup Utility . . . .............. 74
Load Setup Defaults – Copy Standard Entries . ........................................ 74
Discard Changes – Discard changes without exiting the BIOS Setup Utility . .............. 74
Save Changes - save changes without exiting the BIOS Setup Utility . . . . . . .............. 74
Save Changes and Power Off ....................................................... 74
Troubleshooting and tips .............................................................. 75
Help if problemsoccur ................................................................... 75
Restoring the hard disk contents under Windows . . ........................................ 76
The notebook’s date or time is incorrect ................................................... 76
Whencertaincharactersareentered on the keyboard, onlynumerals are written ............. 76
The notebook’s LCD screen remains blank . . . . ............................................ 77
The LCD screen is difficulttoread ........................................................ 77
The externalmonitorremains blank ...................................................... 77
The externalmonitorisblankorthe imageisunstable ..................................... 78
The notebook cannot be started . . . ....................................................... 78
The notebook stops working . . ........................................................... 79
The printer does not print . . . . . ........................................................... 79
The radio connection to a network does not work . . ........................................ 79
Acousticwarnings ....................................................................... 80
SmartCard reader is not recognised. . . . ................................................... 80
SmartCardPINforgotten ................................................................ 80
SmartCardlost ......................................................................... 80
Error messagesonthescreen ........................................................... 81
Technicaldata ......................................................................... 83
LIFEBOOK ............................................................................. 83
Rechargeablebattery ................................................................... 83
Mains adapter .......................................................................... 84
Manufacturer’snotes .................................................................. 85
Disposalandrecycling .................................................................. 85
Declarationsof Conformity ............................................................... 85
CEmarking ............................................................................ 85
Radio frequencies used . . . ........................................................... 86
Index .................................................................................. 87
Fujitsu 5
Contents
6Fujitsu
Innovative technology
Innovative technology
... and ergonomic design make your device a reliable and convenient companion.
The device boots very quickly, is ready for immediate use and offers a particularly
long operating time because of its high capacity battery.
With the user-friendly "BIOS Setup Utility" you can control your notebook’s hardware and better
protect your system against unauthorised access by using the powerful password properties.
Information on the connections and user components of your notebook
canbefoundin"Ports and controls", Page 9.
Further information
The Windows drivers for your device can be found on our Internet site.
The factory installation of your device does not support any other operating
system. Fujitsu Technology Solutions accepts no liability whatsoever
if any other operating system is used.
Software oriented components of these instructions refer to Microsoft products,
if they come within the scope of the delivery.
If you install other software products, pay attention to the operating
instructions of the manufacturer.
Fujitsu 7
Innovative technology
Notational conventions
Pay particular attention to text marked with this symbol. Failure to observe
these warnings could pose a risk to health, damage the device or lead
to loss of data. The warranty will be invalidated if the device becomes
defective through failure to observe these warnings.
Indicates important information for the proper use of the device.
►Indicates an activity that must be performed
Indicates a result
This font indicates data entered using the keyboard in a program dialogue or at
the command line, e.g. your password (Name123) or a command used to
start a program (start.exe)
This font indicates information that is displayed on the screen by a program, e.g.:
Installation is complete.
This font Indicates
• terms and texts used in a software interface, e.g.: Click on Save
• names of programs or files, e.g. Windows or setup.exe.
"This font" Indicates
• cross-references to another section, e.g. "Safety information"
• cross-references to an external source, e.g. a web address: For more
information, go to "http://www.fujitsu.com/fts/"
• Names of CDs, DVDs and titles or designations for other materials,
e.g.: "CD/DVD Drivers & Utilities" or "Safety/Regulations" manual
Key indicates a key on the keyboard, e.g: F10
This font indicates terms and texts that are emphasised or highlighted, e.g.: Do
not switch off the device
8Fujitsu
Ports and controls
Ports and controls
This chapter presents the individual hardware components of your device. It gives
an overview of the indicators and ports of the device. Please familiarise yourself with
these components before you start to work with the device.
Front
LIFEBOOK E546:
10
1
3
1
7
5
8
9
11
7
2
5
6
4
1 = Microphone (optional)
2 = WebCam (optional)
3 = WebCam LED (optional)
4 = Touchpad
5 = Loudspeakers
6 = TouchStick (optional)
7 = Status indicators
8 = Application keys
9 = ON/OFF switch
10 = Fingerprint sensor (optional)
11 = Touchpad buttons (click buttons)
Fujitsu 9
Ports and controls
LIFEBOOK E556:
4
6
10
1
3
1
5
7
5
8
9
11
7
2
1 = Microphone (optional)
2 = WebCam (optional)
3 = WebCam LED (optional)
4 = Touchpad
5 = Loudspeakers
6 = TouchStick (optional)
7 = Status indicators
8 = Application keys
9 = ON/OFF switch
10 = Fingerprint sensor (optional)
11 = Touchpad buttons (click buttons)
Left side
123 4 5 6 7 8
1 = DC input connector (DC IN)
2 = Ventilation slots
3 = LAN port
4 = Monitor port (VGA)
5 = DisplayPort
6 = USB 3.0 port with charging function
(Anytime USB charge)
7 = SmartCard reader (optional)
8 = Memory card slot
10 Fujitsu
Ports and controls
Right side
1 2 345 6
1 = Headphone port
2 = Microphone port
3=USBport3.0
4 = USB port 3.0
5 = Module bay with optional optical drive
6 = Security Lock device
Rear
1
1 = Optional serial port (only LIFEBOOK E556)
Fujitsu 11
Ports and controls
Bottom
2
24
5
3
1
6
7
1 = Module release
2 = Battery release
3 = Port replicator port
4 = Battery compartment (SIM card
under the battery)
5 = Ventilation slot cover
6 = Memory service compartment
7 = Hard disk service compartment
12 Fujitsu
Important notes
Important notes
ImportantnotesNotes
This chapter contains essential safety information which must be followed
when working with your notebook. Other notes also provide useful information
which will help you with your notebook.
Safety notes
SafetynotesNotes
Please follow the safety notes provided in the "Safety/Regulations" manual
as well as the safety notes given below.
Please pay special attention to the sections in the manual marked
with the symbol on the left.
When connecting and disconnecting cables, observe the relevant
notes in this operating manual.
Read the information on the ambient conditions in the "Technical data",
Page 83 and "First-time setup of your device", Page 16 before preparing your
notebook for use and switching it on for the first time.
When cleaning the device, please observe the relevant notes in the
section "Cleaning the notebook", Page 15.
Pay attention to the additional safety notes for devices with radio components
provided in the "Safety/Regulations" manual.
Please refer to the notes in the chapter "Removing and installing
components during servicing", Page 64.
This notebook complies with the relevant safety regulations for data processing
equipment. If you have questions about using your notebook in a particular area,
please contact your sales outlet or our Hotline/Service Desk.
Additional safety notes for devices with
radio components
Radiocomponent :WirelessLAN:Bluetooth,safetynotes
If a radio component (Wireless LAN, Bluetooth, UMTS, LTE) is incorporated into your notebook,
you must be sure to observe the following safety notes when using your notebook:
• Switch off the radio components when you are in an aircraft or driving in a car.
• Switch off the radio components when you are in a hospital, an operating room or near a medical
electronics system. The transmitted radio waves can impair the operation of medical devices.
• Switch off the radio components when you let the device get near flammable
gases or into hazardous environments (e.g. petrol station, paintshops), as the
transmitted radio waves can cause an explosion or a fire.
For information on how to switch radio components on and off, see chapter
"Switching the wireless components on and off", Page 45.
Fujitsu 13
Important notes
Energy saving
NotesEnergyEnergysaving
Switch the notebook off when it is not in use. Switch off external, connected devices if you
are not using them. If you use the energy saving functions, the notebook uses less energy.
You will then be able to work for longer before having to recharge the battery.
Energy efficiency is increased and the environmental impact is reduced.
You save money while protecting the environment.
Energy saving under Windows
►Make use of the power management features (see ""Using the power-management features",
Page 39").
Travelling with yournotebook
MobileoperationNotesTra nspor tationNotebook
Please observe the points listed below when travelling with your notebook.
Before you travel
►Back up important data stored on your hard disk.
NotebookTravel,notebook
►Switch off the radio component for data security reasons. With data traffic via a wireless
connection, it is also possible for unauthorised third parties to receive data.
Information on activating data encryption is provided in the documentation
for your radio component.
►If you wish to use your notebook during a flight, first check with the flight
attendants if it is OK to do so.
When travelling in other countries
►If you are travelling abroad, check that the mains adapter can be operated with the
local mains voltage. If this is not the case, obtain the appropriate mains adapter for
your notebook. Do not use any other voltage converter!
►Check whether the local mains voltage and the power cable are compatible. If this is
not the case, buy a power cable that matches the local conditions.
►Enquire with the corresponding government office of the country you will be
travelling in as to whether you may operate the radio component integrated in
your notebook there (see also "CE marking", Page 85).
14 Fujitsu
Important notes
Notebook: transporting
Protect the notebook from severe shocks and extreme temperatures
(e.g. direct sunlight in a car).
►If your device has an optical drive, remove all data media (e.g. CD, DVD) from the drives.
TransportationNotebook
►Switch the notebook off.
►Unplug the mains adapter and all external devices from the power socket.
►Disconnect the mains adapter cable and the data cables for all external devices.
►Close the LCD screen.
►To protect against damaging jolts and bumps, use a notebook carrying
case to transport your notebook.
Cleaning the notebook
Do not clean any interior parts yourself; leave this job to a service technician.
Only use cleaning products designed for computers. Normal household
cleaners and polishes can damage the markings on the keyboard and the
device, the paintwork or the notebook itself.
Ensure that no liquid enters the notebook.
The LCD screen very sensitive to scratches. Only clean the display
surface with a very soft, slightly damp cloth.
►Switch the notebook off.
CleaningNotesNotebookKeyboardTouchpadLCDscreenCrystalView display
►In order to prevent accidentially switching the device on, remove the power cable from the mains
adaptor and remove the battery (see "Removing and installing the battery", Page 31).
The surface can be cleaned with a dry cloth. If particularly dirty, use a cloth which has
been moistened in mild domestic detergent and then carefully wrung out.
To clean the keyboard and the touchpad, if available, you can use disinfectant wipes.
Ensure that no liquid enters the device.
Fujitsu 15
First-time setup of your device
First-time setup of your device
First- timese tupGettingstarted
Please read the chapter "Important notes", Page 13.
If your device is equipped with a Windows operating system, the necessary
hardware drivers and supplied software are already pre-installed.
Before you switch on the device for the first time, connect it to the mains voltage
using the mains adapter, see "Mains adapter connecting", Page 17.Themains
adapter must be connected during the entire installation process.
A system test is performed when your device is first switched on. Various messages
can appear. The display may remain dark for a short time or may flicker.
Please follow the instructions on the screen.
NEVER switch off your device during the first-time setup process.
On delivery, the battery can be found in the battery compartment or in the accessories kit.
The battery must be charged if you want to operate your device using the battery.
When used on the move, the built-in battery provides the device with the necessary power. You
can increase the operating time by using the available energy-saving functions.
For instructions on how to connect external devices (e.g. mouse, printer) to your
device, please refer to the operating manual for your device.
Unpacking and checking the device
Should you discover any damage that occurred during transportation,
notify your local sales outlet immediately!
►Unpack all the individual parts.
PackagingTran sport
►Check your device for any visible damage which may have occurred during transportation.
You may need the packaging in the future, if you need to transport your device.
16 Fujitsu
First-time setup of your device
Selecting a location
SelectingalocationDeviceMainsadapter
Select a suitable location for the device before setting it up. Follow
the instructions below when doing so:
• Never place the device or the mains adapter on a heat-sensitive surface.
The surface could be damaged as a result.
• Never place the device on a soft surface (e.g. carpeting, upholstered furniture,
bed). This can block the air vents and cause overheating and damage.
• The underside of the device heats up during normal operation. Prolonged contact
with the skin may become unpleasant or even result in burns.
• Place the device on a stable, flat, non-slippery surface. Please note that the
rubber feet of the device may mark certain types of delicate surfaces.
• Keep other objects at least 100 mm / 3.97" away from the device and
its mains adapter to ensure adequate ventilation.
• Never cover the ventilation slots of the device.
• Do not expose the device to extreme environmental conditions. Protect
the device from dust, humidity, and heat.
Mains adapter connecting
Preparingforo perationMainsadapter
Observe the safety notes in the enclosed "Safety/Regulations" manual.
The supplied power cable conforms to the requirements of the country in
which you purchased your device. Make sure that the power cable is approved
for use in the country in which you intend to use it.
3
1
2
►Connect the power cable (1) to the
mains adapter.
►Plug the mains cable (2) into a mains outlet.
►Connect the mains adapter cable (3) to
the DC jack (DC IN) of the device.
Fujitsu 17
First-time setup of your device
Switching on the device for the first time
Switchingonforthefirstt ime
When you switch on the device for the first time, the supplied software is
installed and configured. Because this procedure must not be interrupted,
you should set aside enough time for it to be fully completed and connect
the device to the mains using the mains adapter.
During the installation process, DO NOT restart the device unless
you are requested to do so!
To make it easier to use your device for the first time, the operating system
is pre-installed on the hard disk.
►Switch on your device.
►During installation, follow the instructions on screen.
If a Windows operating system is installed on your device, you will find more
information on the system and drivers, help programmes, updates, manuals etc. on
the device or on the Internet under "http://www.fujitsu.com/fts/support/".
You can find information and help on the Windows operating system functions
on the Internet at "http://windows.microsoft.com".
18 Fujitsu
Working with the notebook
Working with the notebook
Notebook,operat ionNotebook
This chapter describes the basics for operating your notebook. Please read the chapter
entitled "Connecting external devices", Page 57 for instructions on how to connect
devices such as a mouse and a printer to the notebook.
Please refer to the notes in "Important notes", Page 13.
Status indicators
Statusindicators
The status indicators provide information about the status of the power supply,
the drives and the keyboard functions.
Fujitsu 19
Working with the notebook
Key Description
Power-on indicator/Standby
StandbyindicatorPower-onindicator
• Indicator is illuminated: The notebook is switched on.
• Indicator flashes: The notebook is in standby mode.
• Indicator is off: The notebook is switched off.
Battery charging indicator/power connector
The state of charge of the battery is shown by the battery indicator.
• Indicator is illuminated (green): The battery is charged or no battery has been
inserted.
• The indicator lights up orange: the mains adapter is connected and the battery
is being charged.
• Indicator flashes orange: the mains adapter is connected but the battery cannot
be charged as the battery is too hot or cold for charging. The charging process
is continued as soon as the battery reaches a permissible temperature again.
• Indicator flashes red: An error has occured.
• The indicator is not illuminated: the mains adapter is not connected.
Battery indicator
• Indicator is illuminated green: The battery is charged to between 51% and
100% of its maximum capacity.
• The indicator is illuminated orange: The battery is charged to between 13% and
50% of its maximum capacity.
• The indicator lights up red: The battery is charged to between 0% and 12% of
its maximum capacity.
• Indicator flashes red: An error has occured.
BatterystatusindicatorBatterysymbolBatteryindicator
Drive indicator
DriveIndicator
Indicator is illuminated: One of the drives (e.g. hard disk, CD/DVD) is being
accessed.
Radio components indicator
• Indicator is illuminated: The wireless components are switched on.
• Indicator is off: The wireless components are switched off.
Num Lock indicator
Indicator
NumLock
Indicator is illuminated: The Num key has been pressed. The virtual numerical
keypad is activated. You can output the characters indicated on the upper right of
the keys.
Caps Lock indicator
IndicatorCapsLock
Indicator is illuminated: The Caps Lock key has been pressed. All the characters
you type will appear in upper case. In the case of overlay keys, the character
printed on the upper left of the key will appear when that key is pressed.
Scroll Lock indicator
Indicator
ScrollLock
Indicator is illuminated: the key combination Fn +Scr has been pressed. The
effect that this key has varies between applications.
Energy saving functions indicator
• Indicator is illuminated: One of the energy saving functions is activated.
•The
indicator is not illuminated: The energy saving functions have been
deactivated.
20 Fujitsu
Working with the notebook
Switching on the notebook
►Open the LCD screen.
Switchingon
►Press the ON/OFF switch for about one
second to switch the notebook on.
The power-on indicator is lit.
Notebook: switching off
Back up your data and close all applications before you switch off your
device. Otherwise data might be lost.
►Shut down the operating system correctly.
Notebook
►If the notebook is not switched off
automatically, press the ON/OFF switch
for approx. five seconds.
►Close the LCD screen.
Fujitsu 21
Working with the notebook
Keyboard
KeyboardNumerickeypadNumeric keypadButtons
The keyboard of your notebook is subject to continuous wear through normal
use. The key markings are especially prone to wear. The key markings are
liable to wear away over the life of the notebook.
The keyboard has been designed to provide all the functions of an enhanced keyboard.
Some enhanced keyboard functions are mapped with key combinations.
The following description of keys refers to Windows. Additional functions supported by the keys
are described in the relevant manuals supplied with your application programs.
The figure below shows how to access the different characters on keys with overlaid functions.
The example applies when the Caps Lock key has not been activated.
The illustrations shown below may differ from your actual device.
0
=
}
+
+
Num
Alt Gr
=
0}
=
0}
=
0}
=
0}
22 Fujitsu
Working with the notebook
Key Description
Backspace key
The Backspace key deletes the character to the left of the cursor.
BackspaceBac kspace
Tab key
The Tab key moves the cursor to the next tab stop.
Tabkey
Enter key (return)
The Enter key terminates a command line. The command you have entered
is executed when you pressthiskey.
EnterkeyReturnEnterLinefeed
Caps Lock key
The Caps Lock key activates the Caps Lock mode, and the corresponding
icon is displayed in the Windows information area. In Caps Lock mode, all
of the characters you type appear in upper case. In the case of overlay
keys, the character printed on the upper left of the key will appear when
that key is pressed. To cancel the Caps Lock function, simply press the
Caps Lock key again.
ShiftkeyCapsLock
Shift key
The Shift key causes uppercase characters to appear. In the case of overlay
keys, the character printed on the upper left of the key appears when that
keyispressed.
ShiftkeyShift
Fn button
The Fn key enables the special functions indicated on overlay keys (see
"Key combinations", Page 25).
Fnkey
Cursor keys
The cursor keys move the cursor in the direction of the arrow, i.e. up, down,
left, or right.
CursorkeysCursorcontrolkeys
Windows key
The Windows key switches between the start screen and the last used
application.
Windowskey
Menu key
The Menu key opens the menu for the active application.
Fujitsu 23
Working with the notebook
Virtual numeric keypad
NumerickeypadVirtual numer icke ypadNumLock
LIFEBOOK E546 has a virtual number block, LIFEBOOK E556
has a separate number block.
To provide the convenience of a numeric keypad, your keyboard is equipped with a virtual
numeric keypad. The special keys of the virtual numeric keypad are recognisable by the numbers
and symbols printed in the upper right corner of each key. If you have switched on the virtual
numeric keypad, you can output the characters shown on the upper right of the keys.
The keyboard layout shown below may differ from your actual device.
1 = Valid characters when the Num
key is not activated
2 = Valid characters when the Num
is activated
Further information about the status indicators can be found in chapter "Status indicators", Page 19.
24 Fujitsu
Working with the notebook
Separate number block
NumerickeypadSepa raten umeric key padNumLock
LIFEBOOK E546 has a virtual number block, LIFEBOOK E556
has a separate number block.
The keyboard of your notebook has a separate number block on the far right.
Key combinations
Keycombinations
The following description of key combinations applies to Windows operating systems. Some of the
following key combinations may not function in other operating systems or with certain device drivers.
Other key combinations are described in the relevant manuals supplied
with your application programs.
Key combinations are entered as follows:
►Press the first key in the combination and keep it pressed.
►While holding the first key down, press the other key or keys in the combination.
Combination Description
Switching the loudspeakers on and off
This key combination switches your notebook’s loudspeakers off
and on.
Fn+F3LoudspeakersLoudspeakers
Switching the touchpad and touchpad buttons on/off
This key combination switches the touchpad and the touchpad
buttons on or off.
Fn+F4
Tou chpa d
Tou chpa dbuttons
Tou chpa d
Fujitsu 25
Working with the notebook
Combination Description
Decrease screen brightness
This key combination decreases the brightness of the screen.
Fn+F6LCDscreenScreenbrightness
Increase screen brightness
This key combination increases the brightness of the screen.
Fn+F7Screenbrightness
Decrease volume
This key combination reduces the volume of the internal
loudspeakers.
Fn+F8Volume
Increase volume
This key combination increases the volume of the internal
loudspeakers.
Fn+F9Volume
Toggle output screen
Use this key combination to select which screen(s) is/are used for
display if an external monitor is connected.
Screen output is possible:
• only on the notebook’s LCD screen
• on the LCD screen of the notebook and the external monitor
at the same time
• only on the external monitor
This setting is useful if you would like a high resolution and a
high refresh rate on an external monitor.
Fn+F10To g g l e o u t p u tscr een
Switch between open applications
Use this key combination to switch between several open
applications.
Alt+Tab
AltCtrl Del
++
Windows security/Task-Manager
This key combination opens the Windows security/Task-Manager
window.
Ctrl+Alt+Del
Back tab
This key combination moves the cursor back to the previous tab
stop.
Shift+TabBacktab
Key combinations using the Windows keys are detailed in the manual
for your operating system.
26 Fujitsu
Working with the notebook
Country and keyboard settings
►Change the country and keyboard settings as described in the documentation for your operating
system.
Application keys
Applicationkeys
Your notebook is equipped with two application buttons.
Button Description
Eco button (E key)
The E button is a convenient way of activating and deactivating energy saving
functions (e.g. reduce screen brightness), see also "Using the power-management
features", Page 39.
If the device is switched off, you can check the battery status with this button. After
pressing the button, the battery indicator lights up briefly. The colour of the indicator
depends on the still available battery charge. For a description of the indicator colours,
see "Status indicators", Page 19.
Wireless Components key
This application key is used to start the WirelessSelector software. The wireless
components that have been activated in the BIOS Setup can be switched on and
off individually.
Fujitsu 27
Working with the notebook
Touchpad and touchpad buttons
Keep the touchpad clean. Protect it from dirt, liquids and grease.
TouchpadTouchpad
Never use the touchpad if your fingers are dirty.
Do not rest heavy objects (e.g. books) on the touchpad or the touchpad buttons.
3
1
2
1 = TouchStick (optional)
2 = Touchpad
3 = Touchpad buttons
You can move the cursor using the touchpad.
The touchpad buttons allow you to select and execute commands. They correspond
to the buttons on a conventional mouse.
You can also deactivate the touchpad using a keyboard shortcut, so that you cannot
move the cursor unintentionally (see chapter "Key combinations", Page 25).
Moving the pointer
►Move your finger on the touchpad.
Touchpad
The pointer will move.
Selecting anitem
►Move the pointer to the item you wish to select.
Touchpad
►Tap t he t ouchpad once or press the left button once.
The item is selected.
Executing commands
►Move the pointer to the field you wish to select.
Tou chp ad
►Tap the touchpad twice or press the left button twice.
The command is executed.
28 Fujitsu
Working with the notebook
Dragging items
►Select the desired item.
Touchpad
►Press and hold the left button and, with your finger on the touchpad, drag
the item to the desired position.
The item will be moved.
LCD screen
LCDscreenNotes
High-quality LCD screens (TFT) are installed in Fujitsu notebooks. For technical reasons,
these screens are manufactured for a particular resolution. An optimum and sharp image can
only be ensured with the resolution intended for the particular screen. A screen resolution
which differs from the specification can result in an unclear image.
The resolution of your notebook’s screen is set to the optimum at the factory.
With the present standards of production technology, absolutely flawless screen images
cannot be guaranteed. There may be a few constantly light or dark pixels (picture
elements) on the screen. The maximum permitted number of such faulty pixels is
specified in the international standard ISO 9241-307 (Class II).
Example:
A screen resolution of 1280 x 800 has 1280 x 800 = 1024000 pixels. Each pixel consists of three
subpixels (red, green and blue), making a total of about 3 million subpixels. According to ISO
9241-307 (class II), a maximum of 2 light and 2 dark pixels and in addition 5 light or 10 dark subpixels
or an equivalent mix (1 light subpixel counts as 2 dark subpixels) are allowed to be defective.
Pixel A pixel consists of 3 subpixels, normally red, green and
blue. A pixel is the smallest element that can be generated
by complete functionality of the display.
Subpixel A subpixel is a separately addressable internal structure
within a pixel that enhances the pixel function.
Cluster A cluster contains two or more defective pixels or
subpixels in a 5 x 5 pixel block.
Background lighting
LCD screens are operated with background lighting. The luminosity of the background
lighting can decrease during the period of use of the notebook. However, you
can set the brightness of your screen individually.
Synchronising the display on the LCD screen and an external monitor
For more information, please refer to the chapter "Key combinations", Page 25
under "Display output, switch between".
Fujitsu 29
Working with the notebook
Webcam
Webcam
Depending on the device variant, a WebCam may be integrated in your notebook.
Depending on the software used, you can use your Webcam to take pictures,
record video clips or take part in web chats.
The WebCam has its own status indicator. The indicator lights up when the WebCam is switched on.
• The picture quality depends on the lighting conditions and the software being used.
• You can only operate the webcam with a particular application (e.g. an Internet telephony
program or a video conferencing program which supports a webcam).
• When using the webcam the notebook support must not wobble.
• The webcam automatically adjusts itself to the current light level. For this reason
the LCD screen may flicker while the light level is adjusted.
Further information on using the webcam and on the additional settings
which are possible for your webcam can be found in the help function
of the program which uses the webcam.
30 Fujitsu
Working with the notebook
Rechargeable battery
RechargeablebatteryBatteryLife,batteryRechargeablebatteryRechargeablebattery
When not plugged into a mains socket, the notebook runs on its built-in battery. You
can increase the life of the battery by caring for the battery properly. The average
battery life is around 500 charge/discharge cycles.
You can extend the battery life by taking advantage of the available energy saving functions.
Charging, caring for and maintaining the battery
BatteryBattery
The notebook battery can only be charged when the ambient temperature is
between 5°C / 41°F and max. 35°C / 95°F.
You can charge the battery by connecting the notebook to the mains adapter
(see "Mains adapter connecting", Page 17).
If the battery is running low you will hear a warning alarm. If you do not connect the mains adapter
within five minutes of the warning alarm described above, your notebook will automatically switch off.
monitoring the battery charging level
BatteryBatterystatusmeter
Windows also has a "Battery status meter" in the taskbar for monitoring the battery capacity. When
you place the mouse pointer on the battery symbol, the system displays the battery status.
Battery storage
BatteryBatterySelf-discharge,batteryChargingcapacity,ba ttery
Store battery packs in a dry environment at a temperature between 0°C / 32°F and 30°C / 86°F. The
lower the temperature at which the batteries are stored, the lower the rate of self-discharge.
If you will be storing batteries for a longer period (longer than two months),
the battery charge level should be approx. 30 %. To prevent exhaustive
discharge which would permanently damage the battery, check the level
of charge of the battery at regular intervals.
To be able to make use of the optimal charging capacity of the batteries, the battery
should be completely discharged and then fully recharged.
If you do not use the batteries for long periods, remove them from the
notebook. Never store the batteries in the device.
Removing and installing the battery
Only use batteries approved by Fujitsu for your notebook.
Never use force when fitting or removing a battery.
Make sure that no foreign bodies get into the battery connections.
Never store a battery for long periods in the discharged state. This
can make it impossible to recharge.
Fujitsu 31
Working with the notebook
Removing a battery
►Prepare for removal, see chapter "Preparing to remove components", Page 65.
3
1
2
►Slide the release button in the direction of the arrow (1) and hold it in place.
►Slide the release button in the direction of the arrow (2).
►Remove the battery from the battery compartment (3).
32 Fujitsu
Working with the notebook
Installing a battery
2
1
►Position the battery at the edge.
►Insert the battery into the battery compartment until it engages positively (1).
►Slide the release button in the direction of the arrow (2).
►Complete the insertion process, see chapter "Finishing component removal", Page 71.
Fujitsu 33
Working with the notebook
Module
ModulebayModules
The design of your notebook enables the flexible use of notebook batteries and drives. The
following modules can be operated in the module bay of your notebook:
• Second hard disk drive
• DVD Super Multi
• Weight Saver
Only use modules designed for your notebook.
Do not use force when installing or removing the module.
Make sure that no foreign objects enter the module bay.
You can swap modules during operation. This means you do not
need to switch off the notebook.
Log off the module via the corresponding symbol in the task bar.
The module can now be removed without any further actions being necessary.
Removing a module
2
1
ModuleDriveWeigh tSaver
►Slide the release mechanism (1) in the direction of the arrow and hold.
►Pull the module (2) out of the module bay.
34 Fujitsu
Working with the notebook
Installing a module
►Place the module into the module bay so that the contacts enter first.
►Push the module into the module bay until you feel it locking into place.
Optical drive
Opticaldrive
This product contains a light emitting diode, classification according to IEC 60825
1:2007: LASER CLASS 1, and must therefore not be opened.
Handling data carriers
Handling
Observe the following guidelines when handling data carriers:
•Avoidtouc
hing the surface of a data carrier. Only handle data carriers by their edges.
• Always store data carriers in their cases. This will protect the data carrier against
being covered in dust, scratched or damaged in any other way.
•Protecty
our data carriers against dust, mechanical vibrations and direct sunlight.
• Avoid storing a data carrier in areas subject to high temperatures or humidity.
You can use data carriers with a diameter of 8 cm / 3.15" or 12 cm / 4.7" in the drive.
When using a data carrier of lesser quality, vibrations and reading errors may occur.
Fujitsu 35
Working with the notebook
CD/DVD indicator
CD/DVDindicator
The CD/DVD indicator flashes when a data carrier is inserted. The indicator goes out when
the drive is ready for reading. The indicator lights up when the drive is being accessed.
You may only remove the data carrier when the indicator is unlit.
If the CD/DVD indicator does not go out after a data carrier has been inserted, but
instead continues to flash, this means that the drive cannot access the data carrier.
Either the data carrier is damaged or dirty or you are using a data
carrier that the drive cannot read.
Inserting or removing a data carrier
InsertingRemoving
The notebook must be switched on.
2
1
►Push the insert/eject button (1).
The drive tray will open.
►Gently pull the drive tray (2) completely out.
►Place the data carrier in the drive tray with
the printed side facing upwards.
or
►Remove a data carrier that has
been inserted.
►Push in the drive tray until you
feel it lock into place.
36 Fujitsu
Working with the notebook
Manual removal (emergency removal)
CD/DVD:ManualremovalofdatacarrierEmergencyrem ovalo fdata carrier
In the event of a power failure or damage to the drive, you can remove the data carrier manually.
1
2
►Switch your notebook off.
►Push a pen or a piece of wire (such as a
paperclip) firmly into the opening (1).
The drive tray is ejected. You can now pull
the drive tray (2) out of the drive.
Removing and fitting the dust removal cover
(ventilation slot cover)
In order to ensure optimum cooling of the components in your notebook, you
should periodically clean the ventilation slot of the heatsink.
This ensures optimum fan performance. You can achieve the best cleaning
results with a small hand-held vacuum cleaner.
If necessary, you can also use a dry brush to release dust from the ventilation slots.
Do not use any cleaning liquids! Ensure that no liquid enters the device.
To avoid overheating of the device, do not remove the ventilation slot
cover when the device is switched on.
►Prepare for removal, see chapter "Preparing to remove components", Page 65.
Fujitsu 37
Working with the notebook
1
2
►Press and hold the lock of the ventilation
slot cover (1) and remove it from its slot (2).
►Clean the dust chamber.
1
►Insert the ventilation slot cover into the
slot (1) at an angle as shown, and ensure
that you feel it click into place.
►Complete the removal, see chapter
"Finishing component removal", Page 71.
38 Fujitsu
Working with the notebook
Using the power-management features
PowerPowerBattery
The notebook uses less power when the available power-management features are used. You
will then be able to work longer when using the battery before having to recharge it.
Power efficiency is increased and environmental pollution reduced. By
choosing the best power options, you can make significant savings and
at the same time help protect the environment.
When you close the LCD screen, depending on the setting in Windows, the
notebook automatically enters a power saving mode.
►Select the power management functions in your Control Panel.
►Select the Screen Saver in your Control Panel.
or
►Right-click on the desktop. Activate the screen saver by clicking on Personalize – Change
Screen Saver.
If you need further information about an option, you can get help with most
settings by pressing F1 to open the Microsoft Help.
When the notebook is in power-saving mode, the following must be remembered:
During power saving mode, open files are held in the main memory
orinaswapfile on the hard disk.
Never turn off your notebook while it is in a power saving mode. If the built-in battery is
nearly empty, close the open files and do not go into power saving mode.
If you do not intend to use your notebook for a long period of time:
►Exit power saving mode if necessary via the mouse or keyboard or by switching on the
notebook.
►Close all opened programs and completely shut down the notebook.
Fujitsu 39
Working with the notebook
Memory cards
Slot
Your notebook is equipped with an integrated memory card reader.
Observe the manufacturer’s instructions when handling the memory cards.
Memorycard
Supported formats
Your notebook supports the following format:
• Secure Digital (SDTM card)
Inserting the memory card
►Carefully slide the memory card into the
slot. The label should be facing upward. Do
not apply excessive force, as otherwise the
delicate contact surfaces could be damaged.
Memorycard
Depending on the particular type
used, the memory card may protrude
slightly from the slot.
Removing the memory card
Memorycard
In order to protect your data, always follow the correct procedure for removing
the card (see the documentation for your operating system).
1
2
►On devices with card locking: Press
on the memory card (1).
Memorycard
The memory card is released and
can now be removed.
►Pull the memory card out of the slot (2).
40 Fujitsu
Working with the notebook
Loudspeakers and microphones
MicrophoneLoudspeakersBassloudspeaker(subwoo fer)Volumeco ntro l
You will find information about the exact position of speakers and microphones
in chapter "Ports and controls", Page 9.
Please refer to chapter "Key combinations", Page 25 for information on setting the volume
and also enabling/disabling the loudspeakers using key combinations.
If you attach an external microphone, the built-in microphone is disabled.
When you connect headphones or external speakers, the built-in speakers are disabled.
Information on connecting headphones and a microphone can be found
in "Connecting external devices", Page 57.
Fujitsu 41
Working with the notebook
SIM card
A SIM Card (Subscriber Identity Module) is a chip card which is inserted in a mobile telephone or
notebook to enable access to a mobile radio network in conjunction with an installed UMTS module.
Follow the instructions supplied by the provider of the SIM card.
The SIM card slot is located in the battery compartment and can only
be accessed when the battery is removed.
Inserting the SIM card
►Prepare for installation of the SIM card, see chapter "Preparing to remove components", Page 65.
►Remove the battery, see "Removing a battery", Page 32.
1
►Pull the SIM card holder out of the slot (1).
42 Fujitsu
Working with the notebook
2
3
►Insert the SIM card (2) into the SIM card holder as shown in the diagram on the SIM card holder.
►Push the SIM card holder back into the slot (3).
►Install the battery again, see "Installing a battery", Page 33.
►Complete the installation, see chapter "Finishing component removal", Page 71.
Fujitsu 43
Working with the notebook
Removing the SIM card
►Prepare for removal of the SIM card, see chapter "Preparing to remove components", Page 65.
►Remove the battery, see "Removing a battery", Page 32.
2
1
►Pull the SIM card holder out of the slot (1).
►Remove the SIM card from the SIM card holder (2).
3
►Push the SIM card holder back into the slot (3).
►Install the battery again, see "Installing a battery", Page 33.
►Complete the removal, see chapter "Finishing component removal", Page 71.
44 Fujitsu
Working with the notebook
Wireless LAN/Bluetooth/UMTS/LTE radio components
The installation of radio components not approved by Fujitsu will invalidate
the certifications issued for this device.
Switching the wireless components on and off
►Press the button to start the WirelessSelector.
The radio component indicator will be illuminated when one or more
radio components is switched on.
If you switch off the radio components, the wireless LAN antenna and the
Bluetooth and UMTS/LTE module will also be switched off.
You can enable and disable the installed radio components individually
using the WirelessSelector programme
Pay attention to the additional safety notes for devices with radio components
provided in the "Safety/Regulations" manual.
Details on using Wireless LAN can be found in the online help system
included in the Wireless LAN software.
You can find more information on how to use Bluetooth on the CD you
received with your Bluetooth software.
You can obtain more information on UMTS / LTE from your service provider.
Setting up WLAN access
• Requirement: A WLAN must be available and you must have the
corresponding access information.
Information on configuring the WLAN access can be found in the
documentation for your operating system.
Fujitsu 45
Working with the notebook
Access via UMTS/LTE
You can purchase the accessories for UMTS/LTE reception from your retailer
or your Fujitsu Technology Solutions dealer.
If you have ordered a UMTS/LTE module, your device will already
be prepared when you receive it.
You will find information on establishing the connection with the UMTS/LTE
network in the documentation for the hardware you plan to use.
Your device can connect with the Internet via UMTS/LTE. To do this, use one
of the following types of connection:
• USB dongle
a USB stick with your mobile phone provider’s SIM card
• a mobile end-device (e.g. mobile phone) with Bluetooth connection
• a mobile end-device (e.g. mobile phone) with data cable
Ethernet and LAN
EthernetLAN
The internal network module of your notebook supports Ethernet LAN. You can use it to
establish a connection to a local network (LAN = Local Area Network).
2
1
►Connect the network cable to the LAN
port of the notebook (1).
►Connect the network cable to your
network connection (2).
Your network administrator can help you to configure and use the LAN connections.
The network cable is not included in the delivery scope. This type of
cable can be obtained from a specialist dealer.
46 Fujitsu
Working with the notebook
Your Port Replicator
The Port Replicator is a device that helps you to quickly connect your notebook to
your peripheral devices, such as a monitor, printer etc.
The features offered by the Port Replicator include standard ports for
monitor, audio, mouse and keyboard.
You need only dock the notebook in order to work with your peripheral devices.
Ports on the Port Replicator
PortReplicatorPorts
11
1
2
3
4
6
7
89
12
10
5
1 = Security Lock device
2 = USB ports (USB 3.0)
3 = eSATA port
4 = LAN port
5=Displayp
orts
6 = DVI-D monitor port
7=VGAmon
itor port
8 = DC jack socket (DC IN)
9 = Headphone and microphone port
10 = ON/OFF button
11 = Connector on the port replicator for the
docking port on the bottom of the notebook
12 = Release
The DVI port and the neighbouring DisplayPort cannot be used at the same time.
Fujitsu 47
Working with the notebook
Connecting the notebook to the Port Replicator
The mains adapter must be connected to the Port Replicator when the
notebook is connected to the Port Replicator.
We recommend that the notebook is not operated with the LCD screen closed when
the notebook is connected to the Port Replicator. The resulting overheating can
cause reduced performance and increased activity of the integrated fan.
PortReplicator
►Disconnect the mains adapter cable from the DC socket (DC IN) of the notebook.
1
►Position the notebook so that it is in line with the back edge of the Port Replicator.
►Place the notebook onto the Port Replicator (1) and ensure that it locks into place correctly.
48 Fujitsu
Working with the notebook
Connecting the mains adapter to the Port Replicator
3
1
2
►Connect the power cable to the
mains adapter (1).
►Plug the power cable into the mains
socket (2).
►Connect the mains adapter cable to the DC
jack (DC IN) of the Port Replicator (3).
When the notebook is connected to a Port Replicator, the operating system creates
a hardware profile for the "Docked" mode. In this profile, for example, the setting is
saved as to which monitor was last used for output. This profile will be loaded, as
soon as the notebook is connected to a Port Replicator of the same type.
Switching on the notebook via the port replicator
►Press the ON/OFF switch on the port
replicator to switch the notebook on.
The power-on indicator of the Port
Replicator lights up.
Fujitsu 49
Working with the notebook
Disconnecting the notebook from the Port Replicator
Windows 7:
Problems may occur if the notebook is removed from the Port Replicator during
operation. We recommend that the notebook is switched off or that the appropriate
undocking function provided by the operating system is executed.
2
1
►Pull the unlocking lever in the direction of the arrow (1), until you hear the notebook unlatch.
►Lift off the notebook (2).
50 Fujitsu
Security functions
Security functions
Securityfunctions
Your notebook has several security features that you can use to secure your
system from unauthorised access.
This chapter explains how to use each function, and what the benefits are.
Please remember that in some cases, for example, forgetting your password,
you may be locked out and unable to access your data. Therefore,
please note the following information:
• Make regular backups to external data carriers such as external hard
drives, CDs, DVDs or Blu-ray Discs.
• Some security functions need you to choose passwords. Make a note
of the passwords and keeptheminasafeplace.
If you forget your passwords you will need to contact the our Service
Desk. Deletion or resetting of passwords is not covered by your warranty
and a charge will be made for assistance.
Configuring the fingerprint sensor
Fingerprintsens orFingerprintsens or
Whether or not your device has a fingerprint sensor depends on the
device configuration you have ordered.
The fingerprint sensor can record an image of a fingerprint. With additional fingerprint
software, this image can be processed and used instead of a password.
1
►You must install the fingerprint software
in order to be able to use the
fingerprint sensor (1).
Fujitsu 51
Security functions
Using the Security Lock
Your device comes with a Security Lock mechanism for the Kensington Lock Cable. You
can use the Kensington Lock Cable, a sturdy steel cable, to help protect your notebook
from theft. The Kensington Lock Cable is available as an accessory.
Fujitsu recommends the use of a combination lock.
K
►Fit the Kensington Lock Cable to the
mechanism on your notebook.
UsingtheKensingtonLockCable
Security LockM echanicalback upAnti-theftprotection
Attach another Kensington Lock Cable to your Port Replicator to protect
your Port Replicator from theft as well.
Configuring password protection in BIOS Setup Utility
Before using the various options for password protection in the BIOS Setup utility
to increase data security, please observe the following:
Makeanoteofthe passwords and keep them in a safe place. If you forget your
supervisor password you will not be able to access your notebook. Deletion of the
password is not covered by your warranty and a charge will be made for assistance.
Password prote ction
Your password can be up to eight characters long and contain letters and numbers.
No distinction is made between uppercase and lowercase.
52 Fujitsu
Security functions
Protecting BIOS Setup Utility (supervisor and user password)
If you have opened these operating instructions on the screen, we
recommend that you print them out. You cannot call the instructions onto
the screen while you are setting up the password.
BIOSSetupUtility
The supervisor password and the user password both prevent unauthorised use of the BIOS Setup
Utility. With the aid of the supervisor password you can access all of the functions of the BIOS
Setup Utility, while the user password will only give you access to some of the functions. You
can only set up a user password if a supervisor password has already been assigned.
Please refer to section "Settings in BIOS Setup Utility", Page 72 for a description
of how to call up and operate the BIOS-Setup-Utility.
Assigning the supervisor and user passwords
►Start the BIOS Setup Utility and go to the Security menu.
►Select the Set Supervisor Password field and press the Enter key.
With Enter new Password: you are asked to enter a password.
►Enter the password and press the Enter key.
Confirm new Password requires you to confirm the password.
►Enter the password again and press the Enter key.
Changes have been saved is a confirmation that the new password has been saved.
►To set the user password, select Set User Password and proceed exactly as
when configuring the supervisor password.
Ifyoudonotwa
nt to change any other settings, you can exit BIOS Setup Utility.
►In the Exit menu, select the option Save Changes & Exit.
►Select Yes and press the Enter key.
PasswordSupervisorpasswordUserpassword
The notebook is then rebooted and the new password comes into effect. It will now be necessary
to first enter your supervisor or user password in order to open the BIOS Setup Utility. Please
note that the user password only provides access to a few of the BIOS settings.
Changing the supervisor or user password
You can only change the supervisor password when you have logged into the
BIOS Setup Utility with the supervisor password.
Password
Supervisorpassword
Userpassword
►Call the BIOS Setup Utility and go to the Security menu.
►When changing the password, proceed exactly as for password assignment.
Fujitsu 53
Security functions
Removing passwords
To remove a password (without setting a new password) perform the following steps:
PasswordSupervisorpasswordUser password
►Start the BIOS Setup Utility and go to the Security menu.
►Highlight the Set Supervisor Password or Set User Password field and press the Enter key.
You will be requested to enter the current password by the Enter Current Password prompt.
You will be requested to enter a new password by the Enter New Password prompt.
►Press the Enter key twice.
►In the Exit menu, select the option Save Changes & Exit.
►Select Yes and press the Enter key.
The notebook will now reboot with the password removed.
Removing the supervisor password simultaneously deactivates the user password.
Password protection for booting of the operating system
With the supervisor password you have set in the BIOS Setup Utility (see
section "Assigning the supervisor and user passwords", Page 53), you can
also prevent starting of the operating system.
Operating system
Activating system protection
►Start the BIOS Setup Utility and go to the Security menu.
Operatingsystem
►Select the Password on Boot option and press the Enter key.
►Select the desired option (Disabled,First Boot or Every Boot) and press the Enter key
►Select the Save Changes & Exit option under Exit.
The notebook reboots. You will be prompted to enter your password (the supervisor password).
Deactivating system protection
►Start the BIOS Setup Utility and go to the Security menu.
Operatingsystem
►Select the Password on Boot option and press the Enter key.
►Select the Disabled option and press the Enter key.
If you do not want to change any other settings, you can exit BIOS Setup Utility.
►Select the Save Changes & Exit option under Exit.
The notebook will reboot. The system is no longer password-protected.
Password protection for the hard disk
If a supervisor password has been assigned, a password for the hard disk can
also be set in the Hard Disk Security menu.
The hard disk is protected by this password. Data on this hard disk can only be read
into another system if the correct password has been entered.
54 Fujitsu
Security functions
Trusted Platform Module (TPM) (device-dependent)
TPMTrustedPlatform Module
To use the TPM, you must activate the TPM in the BIOS Setup before the software
is installed. The condition for this is that you have assigned at least the supervisor
password (see "Security functions", Page 51).
Enabling TPM
• Requirement: You have set a supervisor password, see "Security functions", Page 51.
►Call up the BIOS Setup and select the Security menu.
►Mark the TPM (Security Chip) Setting field and press the Enter key
►Select the "Security Chip" "Enabled" entry to activate the TPM
Once you have activated the TPM through a reboot, the Clear Security Chip menu option appears.
With Clear Security Chip, you can delete the owner in the TPM, if the TPM has already
been used. With Enabled, all secret keys generated by applications (e.g. SRK - Storage
Root Keys, AIK - Attestation Identity Keys, etc.) are deleted.
Please note that you will then no longer be able to access the data you have
encrypted with the keys based on that holder.
►Select the Exit Saving Changes option in the Exit menu.
►Press the Enter key and select Yes.
The notebook will restart, and TPM will be enabled after the reboot.
Disabling TPM
• Requirement: You have set a supervisor password, see "Security functions", Page 51.
►Call up the BIOS Setup and select the Security menu.
►Mark the TPM (Security Chip) Setting field and press the Enter key.
►Select the "Security Chip" "Disabled" entry to deactivate the TPM
►From the Exit menu, choose the option Exit Saving Changes.
►Press the Enter key and select Yes.
Your notebook will now restart and TPM will be disabled.
Fujitsu 55
Security functions
SmartCard reader
Securityfunctions,Securityfunctions
Depending on the device configuration level, your notebook is equipped
with a SmartCard reader.
SmartCards are not supplied as standard equipment. You can use all SmartCards that comply with
the ISO standard 7816-1, -2 or -3. These SmartCards are available from various manufacturers.
With the appropriate software you can use your SmartCard as an alternative to password protection,
but also as a digital signature, for encrypting your e-mails or for home banking.
We recommend that you always use two SmartCards. Always keep one of the SmartCards
in a safe place if you are carrying the other SmartCard with you.
In order to be able to take advantage of all the security features of your notebook,
you will need a CardOS SmartCard from Fujitsu.
The SmartCard can only be used with a PIN, offering maximum protection even if
you lose the SmartCard. In order to maximise your security, the CardOS SmartCard
is disabled if three incorrect attempts are made to enter the PIN.
When you use the CardOS SmartCard for the first time, you will either need to enter the
preset PIN "12345678" or the PIN given to you by your systems administrator.
Inserting the SmartCard
Do not use force when inserting and removing the SmartCard.
Make sure that foreign objects do not fall into the SmartCard reader.
►Slide the SmartCard into the SmartCard
reader with the chip facing upwards (on
some variants it faces down) and to the front.
56 Fujitsu
Connecting external devices
Connecting external devices
Always refer to the safety information provided in "Important notes", Page 13 before
connecting or disconnecting any devices to or from your notebook.
Always read the documentation supplied with the device you wish to connect.
Never connect or disconnect cables during a thunderstorm.
Never pull at a cable when disconnecting it. Always grasp the plug.
With some devices such as USB devices, it is not necessary to switch off
the notebook and the device before connecting/disconnecting. For more
information about whether or not devices need to be switched off, please refer
to the documentation supplied with the external device.
Some of the external devices require special drivers (see the operating
system and external device documentation).
Fujitsu 57
Connecting external devices
Connecting an external monitor
An analogue monitor is connected to the analogue VGA monitor port, a digital monitor
to the DisplayPort or to the DVI-D monitor port on the optional Port Replicator.
Monitor output is limited to a maximum of two monitors at any one time (see "Key
combinations", Page 25, section "Toggle output monitor").
MonitorVGAcon nection socketMonitorportMonitorport
Digital DisplayPort (on notebook or on optional
port replicator)
Analogue VGA monitor port (on notebook or on
optional port replicator)
Digital DVI-D monitor port (on the optional Port
Replicator)
►Switch off the notebook and the external monitor.
►Plug the data cable of the external monitor into the monitor port.
►First switch on the external monitor and then the notebook.
You can also switch between the external monitor and the LCD monitor of the
notebook, see chapter "Key combinations", Page 25.
You can display the same picture on the external monitor and the
notebook LCD monitor simultaneously.
If you wish to operate the monitor via a DVI port, use the optional Port
Replicator available for your notebook.
58 Fujitsu
Connecting external devices
Connecting external devices to the serial
port (optional)
SerialportSerialportExternaldevicesDevices
External devices (e.g. a printer or scanner) can be connected to the optional serial port.
►Connect the data cable to the
external device.
►Connect the appropriate data cable for
the device to the serial port.
For an exact description of how to connect external devices to the corresponding
port, please see the external device documentation.
Port settings
Serialport,
You can change the port settings (e.g. address, interrupt) in the BIOS Setup.
Device drivers
Devicedrive rs,
Devices connected to the serial port require drivers. Your operating system
already includes many drivers. If the required driver is missing then it will be
necessary to install it. Up-to-date drivers are usually available on the Internet
or will be supplied with the device on a data carrier.
Fujitsu 59
Connecting external devices
Connecting USB devices
USBports
On the USB ports, you can connect external devices that also have a USB port
(e.g. a DVD drive, a printer, a scanner or a modem).
USB devices are hot-pluggable. This means you can connect and disconnect
devices while your operating system is running.
USB 1.x has a maximum data transfer rate of 12 Mbit/s.
USB 2.0 has a data transfer rate of up to 480 Mbit/s.
USB 3.0 has a data transferrateofupto5Gbit/s.
Additional information can be found in the documentation for the USB devices.
►Connect the data cable to the
external device.
►Connect the data cable to a USB
port of the notebook.
Device drivers
USB devices will be automatically recognised and installed by your operating system.
60 Fujitsu
Connecting external devices
USB port with charging function (Anytime USB charge)
USBchargingfunction
It is recommended that the notebook be operated with the power supply connected
whenever the USB port with charging function is in use, as this function will drain
the battery more quickly if an external USB device is being charged.
The power supply unit must already be connected when the notebook is
switched off, as otherwise the USB charging function will be disabled and
the connected USB devices will not be charged.
Some USB devices (e.g. mobile telephones) require a driver in order to utilise the
USB charging function. In this case the USB charging function will not work when the
notebook is switched off, as no drivers are active when the notebook is switched off.
You can use this USB port to charge or supply power to a USB device (e.g. to charge a PDA
or a mobile phone or to connect a USB lamp), even if the notebook is switched off.
Fujitsu 61
Connecting external devices
Connecting an external SATA hard disk (eSATA)
(port replicator only)
The notebook itself does not have an eSATA port. The optional Port Replicator
available for your notebook provides this port.
An external SATA hard disk can be connected at the eSATA port. This allows you
to expand the internal hard disk capacity as you wish.
The length of the eSATA cable must not exceed 2 metres. Consult a specialist
dealer for advice on which eSATA data cable is suitable for your external eSATA
hard disk. Make sure that the hard disk has its own external power supply.
The data transfer rate is up to 2,400 Mbit/s.
eSATA
►Connect the data cable to the external
device.
►Connect the data cable to the eSATA port.
Device drivers
The eSATA hard disk is automatically recognised by your operating system and installed.
You will find more information in the documentation for the external SATA
hard disk and the operating system.
Safe removal of eSATA and USB devices
Always correctly remove the device according to the rules described below,
to ensure that none of your data is lost.
►Left-click on the symbol to remove hardware safely.
►Select the device you wish to shut down and remove.
►Press the "Enter" key.
Wait for the dialogue box which tells you that it is now safe to remove the device.
62 Fujitsu
Connecting external devices
Connecting external audio devices
Microphone port/Line In
Audiodevices, connectingAudioportsMicrop hone,connecti ng
The microphone port/Line In allows you to connect an external microphone, a MiniDisc
player, MP3 player, CD player or a tape deck to your notebook.
►Connect the audio cable to the
external device.
►Connect the audio cable to the microphone
port/Line In of the notebook.
Headphone port
Connectingaudio dev ices
AudioportsConnecting headphones
You can connect headphones or external loudspeakers to your notebook via the headphone port.
►Connect the audio cable to the
external device.
►Connect the audio cable to the headphone
port of the notebook.
The internal loudspeakers are disabled.
If you purchase a cable from a retailer, please note the following information:
The headphone port on your notebook is a "3.5 mm jack socket".
If you want to connect headphones or a speaker you will need a "3.5 mm jack plug".
Fujitsu 63
Removing and installing components during servicing
Removing and installing components
during servicing
Only qualified technicians should repair your notebook. Unauthorised
opening or incorrect repair may greatly endanger the user (electric shock,
fire risk) and will invalidate your warranty.
Components
Serv icing
After consulting the Hotline/Service Desk, you may remove and install the
components described in this chapter yourself.
If you remove and install components without consulting the Hotline/Service
Desk, then the warranty of your notebook will be voided.
Notes on installing and removing boards
and components
• Switch the notebook off and pull the power plug out of the mains socket.
• Always remove the battery.
• Take care when you use the locking mechanisms on the battery and any other component.
• Never use sharp objects such as screwdrivers, scissors or knives as leverage to remove covers.
NotesBoardESD
Boards with electrostatic sensitive devices (ESD) are marked with the label
shown.
When handling boards fitted with ESDs, you must always observe the following
points:
• You must always discharge static build up (e.g. by touching a grounded
object) before working.
• The equipment and tools you use must be free of static charges.
• Remove the power plug from the mains supply before inserting or removing
boards containing ESDs.
• Always hold boards with ESDs by their edges.
• Never touch pins or conductors on boards fitted with ESDs.
64 Fujitsu
Removing and installing components during servicing
Preparing to remove components
If you are going to remove or change system components, prepare for the removal as follows:
Please observe the safety information in chapter "Important notes", Page 13.
Remove the power plug from the mains outlet !
►Switch the device off.
The device must not be in energy-saving mode !
►Close the LCD screen.
►Remove all the cables from the device.
►Turn the device over and place it on a stable, flat and clean surface. If necessary, lay an
anti-slip cloth on this surface to prevent the device from being scratched.
►Remove the battery (see "Removing a battery", Page 32).
Installing and removing memory expansion
MemorymoduleMainmemoryRemovingmemory
Systemexpansi on
Systemexpansi on
If you are asked by the Hotline/Service Desk to remove and install the memory
expansion yourself, proceed as follows:
Please observe the safety information in chapter "Important notes", Page 13.
When installing/removing memory modules, the battery must be removed from
the notebook and the notebook must not be connected to the power supply,
see "Preparing to remove components", Page 65.
Only use memory expansion modules that have been approved for your
notebook (see "Technical data", Page 83).
Never use force when installing or removing a memory extension.
Make sure that foreign objects do not fall into the memory extension compartment.
You must open the service compartment to remove or install a memory module. On some devices,
opening the compartment may expose other components. These components should be removed
and replaced only by authorised specialists. Therefore, be sure to observe the following:
Individual components can become very hot during operation. Therefore, we
recommend that you wait one hour after switching off the notebook before removing
or installing memory modules. Otherwise, there is a risk of suffering burns!
As some components are exposed that are sensitive to static electricity, please take
note of chapter "Notes on installing and removing boards and components", Page 64.
Fujitsu 65
Removing and installing components during servicing
Removing a cover
►Prepare for removal, see "Preparing to remove components", Page 65.
1
2
►Remove the screw (1).
Keep the screw in a safe place.
►Lift the cover off the notebook (2).
Removing memory modules
3
2
1
1
►Carefully push the two mounting
clips outwards (1).
MemoryexpansionMemorymodule
The memory module snaps upwards (2).
►Pull the memory module out of its slot
in the direction of the arrow (3).
66 Fujitsu
Removing and installing components during servicing
Installing a memory module
2
a
1
►Insert the memory module with the contacts
and the recess (a) facing the slot (1).
MemoryexpansionMemorymodule
►Carefully push the memory module
downwards until you feel it click
into place (2).
Attaching the cover
2
1
►Place the cover in the correct mounting position (1).
►Tighten the screw (2).
►Complete the installation, see "Finishing component removal", Page 71.
Fujitsu 67
Removing and installing components during servicing
Removing and installing the harddisk
Removing a cover
1
2
►Remove the screw (1).
Keep the screws in a safe place. If you are removing more than one component at
the same time, store the screws for the individual components separately from each
other. If you install the wrong screws, components may be damaged.
The screws are not all the same length and when the cover is installed,
the correct screws must be used.
►Lift the cover off the notebook (2).
68 Fujitsu
Removing and installing components during servicing
Removing a hard disk
1
1
►To release the hard disk from the
contacts, pull the hard disk in the
direction of the arrow (1).
2
►Remove the hard disk from the hard
disk compartment (2).
Fujitsu 69
Removing and installing components during servicing
Installing a hard disk
1
►Place the hard disk into the hard
disk compartment (1).
2
2
►Pull the hard disk in the direction of the
arrow (2) until it engages in the contacts.
70 Fujitsu
Removing and installing components during servicing
Attaching the cover
2
1
►Place the cover in the correct mounting position (1).
►Tighten the screw (2).
Finishing component removal
After you have removed or changed the system components as you required, please
prepare your device for operation again as follows:
►Install the battery again (see "Installing a battery", Page 33).
►Turn the notebook the right way up again and place it on a flat surface.
►Reconnect the cables that you disconnected before.
Fujitsu 71
Settings in BIOS Setup Utility
Settings in BIOS Setup Utility
BIOSSetupUtilitySystemsettings,BIOSSe tupUtilityConfiguration,BIOSSetupUtilitySetupSystem configurationHardwareconfiguration
The BIOS Setup Utility allows you to set the system functions and the hardware
configuration for the notebook.
When it is delivered, the notebook is set to factory default settings. You can
change these settings in BIOS Setup Utility. Any changes you make take effect as
soon as you save and exit the BIOS Setup Utility.
The BIOS Setup Utility program contains the following menus:
About Displays information relating to the BIOS, processor and notebook
System Advanced system settings
Advanced Configuration of various hardware components, such as mouse, keyboard,
processor
Security Password settings and security functions
Boot Configuration of the start-up sequence
Exit Exits the BIOS Setup Utility
Starting the BIOS Setup Utility
►Reboot the device (switch off/on or reboot the operating system).
BIOSSetupUtility
Depending on the Fast Boot setting in the BIOS Setup utility,thefollowing
information may appear on the screen during start:
<F2> BIOS Setup <F12> Boot Menu
►Press the function key F2 .
►If a password has been assigned, enter the password and press the Enter key.
If you have forgotten the password, contact your system administrator
or contact our customer service centre.
The BIOS Setup Utility starts.
72 Fujitsu
Settings in BIOS Setup Utility
Operating BIOS Setup Utility
BIOSSetupUtility
Press the F1 key to display help on the operation of the BIOS Setup Utility. The description
of the individual settings is shown in the right-hand window of the BIOS Setup Utility.
With the F9 key you can load the default settings of the BIOS Setup Utility.
►Use the cursor keys ←or →to select the menu you wish to access to make changes.
The menu is displayed on the screen.
►Select the option you want to change with the cursor keys ↑or ↓.
►Press the Enter key.
►Press the ESC key to exit the selected menu.
►For future reference, make a note of the changes you have made (for example, in this manual).
Fujitsu 73
Settings in BIOS Setup Utility
Exiting BIOS Setup Utility
BIOSSetupUtility
You need to select the desired option in the Exit menu and activate it by pressing the Enter key:
Exit Saving Changes - save changes and exit BIOS Setup Utility
►To save the current menu settings and exit the BIOS Setup Utility, select Exit Saving Changes and Yes .
The notebook is rebooted and the new settings come into effect.
Exit Discarding Changes – Discard changes and
exit BIOS Setup Utility
►To discard the changes, select Exit Discarding Changes and Yes.
The settings in place when BIOS Setup Utility was called remain effective. BIOS
Setup Utility is terminated and the notebook is rebooted.
Load Setup Defaults – Copy Standard Entries
►To copy the standard entries for all menus of the BIOS Setup Utility,
choose Load Setup Defaults and Yes.
Discard Changes – Discard changes without exiting
the BIOS Setup Utility
►To discard the changes you have made, select Discard Changes and Yes.
The settings in place when BIOS Setup Utility was called remain effective.
You can now make additional settings in the BIOS Setup Utility.
►IfyouwanttoexitBIOS Setup Utilitywith these settings, select Exit Saving Changes and Yes.
Save Changes - save changes without exiting
the BIOS Setup Utility
►To save the changes, select Save Changes and Yes.
The changes are saved. You can now make additional settings in the BIOS Setup Utility.
►If you want to exit BIOS Setup Utility with these settings, choose Exit Saving Changes and Yes.
Save Changes and Power Off
►To save the changes and switch off your device, select Save Changes and Power Off and Yes.
The changes are saved. Your device is shut down.
74 Fujitsu
Troubleshooting and tips
Troubleshooting and tips
TroubleshootingTipsFaultTroubleshooting
Follow the safety notes in the "Safety/Regulations" manual when
connecting or disconnecting cables.
If a fault occurs, try to correct it as described. If you fail to correct the problem, proceed as follows:
►Make a note of the steps and the circumstances that led to the fault. Also
make a note of any error messages displayed.
►Switch the notebook off.
►Please contact the Hotline/Service Desk.
You can find the telephone numbers in the service desk list. Please have
the following information ready when you call:
• The model name and serial number of the notebook. The serial number is
located on a sticker on the underside of the notebook.
• Notes of any messages that appear on the screen and information on acoustic signals.
• Any changes you have made to the hardware or software since
receiving the notebook.
• Any changes you have made to the BIOS Setup settings since receiving the notebook.
• Your system configuration and all peripheral devices connected to your system.
• Your sales contract.
Our notebooks have been designed primarily with mobile applications in mind. This
means that considerable effort has been made to optimise components and equipment
in terms of weight, space and energy requirements. Depending on the particular
configuration you have purchased, it is possible that functionality may be slightly reduced
compared to a desktop PC if you are running processor-intensive gaming software, e.g.
games with intensive 3D graphics. Updating your hardware with drivers which have not
been approved by Fujitsu Technology Solutions may result in performance losses, data
losses or malfunction of the equipment. A list of approved drivers and current BIOS
versions can be downloaded from: "http://support.ts.fujitsu.com/Download/Index.asp"
Help if problems occur
Should you encounter a problem with your computer that you cannot resolve yourself:
►Note the ID number of your device. The ID number is found on the type rating
plate on the back or underside of the casing.
►For further clarification of the problem, contact the Service Desk for your country (see the
Service Desk list or visit the Internet at
"http://support.ts.fujitsu.com/contact/servicedesk/ServiceDeskNumber_Int.asp"). When you
do this, please have ready the ID number and serial number of your system.
Fujitsu 75
Troubleshooting and tips
Restoring the hard disk contents under Windows
Harddisk:Operatingsystem,restoring
You can use the "Windows Recovery CD" (optionally available) and the "Drivers & Utilities
CD/DVD" to reinstall the operating system.
The instructions are provided on the case of the Recovery CD.
During the reinstall process your personal files and any installed programs
will be deleted. We advise you to backup your files to an external hard
drive, or CD / DVD disk before you start.
►Switch the notebook on.
Depending on the Fast Bootsetting in the BIOS Setup utility,thefollowing
information may appear on the screen during start:
<ESC>Diagnostic screen <F12>Boot Menu <F2>BIOS Setup
►When this message appears, press the function key F12 .
►Insert the "Windows Recovery CD" into the optical drive.
►Select CD-ROM and press the Enter key.
►Follow the instructions on the screen.
After the installation you must install all the drivers again. Some installed hardware
components will not be correctly supported until this has been done.
►Insert the "Drivers & Utilities" CD/DVD into the optical drive. The CD starts automatically.
►Click on the Desk Update button.
►Select Automatic driver installation (Express) and click on Start installation.
►Follow the instructions on the screen.
►Restart your notebook when the driver installation is completed.
The notebook’s date or time is incorrect
Timenotcorrec tTime notcorrectInc or rec t dat e/ti meDateisincorrectBufferbattery,load
Cause Troubleshooting
Time and date are incorrect. ►With the BIOS-Setup-Utility, you can set the
date and time in the main menu.
If the time and date are still set incorrectly after
switching on the notebook.
►Please contact your sales outlet or our
Hotline/Service Desk.
When certain characters are entered on the
keyboard, only numerals are written
Abeepsounds ever ys econd
Cause Troubleshooting
The virtual numeric keypad of your device is
activated, see "Virtual numeric keypad", Page 24
►Press the Num key.
76 Fujitsu
Troubleshooting and tips
The notebook’s LCD screen remains blank
LCDscreenLCDscreenistoodark
Cause Troubleshooting
Monitor is switched off. ►Press a key or touch the touchpad.
External monitor or television set connected. ►Press the key combination to switch the
screen output, see "Key combinations",
Page 25.
The LCD screen is difficult to read
LCDscreenLCDscreen
Cause Troubleshooting
Reflected glare ►Turn the notebook or alter the tilt of the LCD
screen.
►Increase the brightness of the screen.
The external monitor remains blank
Monitor
Cause Troubleshooting
Monitor is switched off. ►Switch the external monitor on.
Power saving has been activated (monitor is
blank).
►Press any key to continue.
Brightness is set to dark. ►Adjust the brightness of the monitor.
Screen output is set to the notebook’s LCD
screen
►Press the key combination to switch the
screen output, see "Key combinations",
Page 25.
The external monitor’s power cable or data
cable is not connected properly.
►Switch off the external monitor and the
notebook.
►Check whether the power cable is plugged
properly into the external monitor and into
the power socket.
►Check whether the data cable is properly
connected to the notebook and the external
monitor (if it is plugged in with a connector).
►Switch on the external monitor and the
notebook.
Fujitsu 77
Troubleshooting and tips
The external monitor is blank or the image is unstable
ScreenMonitor
Cause Troubleshooting
The wrong external monitor has been selected
or the wrong screen resolution has been set for
the application program.
►Terminate the application program in
Windows by pressing Alt +F4 .Ifthe
fault persists after closing the program, use
the key combination for switching the screen
output (see "Key combinations", Page 25)to
switch over to the notebook’s LCD screen.
Change the following setting:
►Set the screen resolution: Set the screen
resolution as described in the documentation
foryouroperatingsystem.
►Select monitor: Select monitor 1 or 2 as
described in the documentation for your
operating system.
The notebook cannot be started
Notebook
Cause Troubleshooting
The battery is not installed correctly. ►Check whether the battery is installed
correctly in its compartment.
►Switch the notebook on.
The battery is dead. ►Charge the battery.
or
►Insert a charged battery.
or
►Connect the mains adapter to the
notebook.
The power adapter is not connected correctly. ►Check whether the mains adapter is
connected correctly to the notebook.
►Switch the notebook on.
78 Fujitsu
Troubleshooting and tips
The notebook stops working
NotebookEnergys aving mode
Cause Troubleshooting
Notebook is in energy saving mode. ►Leave energy saving mode.
An application programme has caused the
malfunction.
►Close the application program or restart
the notebook (by restarting the operating
system or switching the device off and back
on again).
The battery is dead. ►Charge the battery.
or
►Insert a charged battery.
or
►Connect the mains adapter to the
notebook.
The printer does not print
Printerdoesnot print
Cause Troubleshooting
The printer is not switched on. ►Make sure that the printer is switched
on and ready for operation (refer to the
documentation supplied with the printer).
The printer is not connected correctly. ►Check that the data cable connecting
the notebook to the printer is properly
connected.
The printer driver is faulty or not correctly
installed, or it is the wrong printer driver.
►Check that the data cable connecting
the notebook to the printer is properly
connected.
►Check whether the correct printer driver is
loaded (refer to the printer documentation).
The radio connection to a network does not work
Theradioconnect iont oa netwo rkdoes not wor k
Cause Troubleshooting
The wireless component is disabled. ►Switch the radio component on (see
"Switching the wireless components on and
off", Page 45).
The wireless component is enabled. Despite
this, the wireless connection to a network does
not work.
►Check whether the radio connection is
switched on via the software.
►Further information on using the radio
component can be found in the help files.
Fujitsu 79
Troubleshooting and tips
Acoustic warnings
Acousticerror messagesErrors
Cause Troubleshooting
A beep sounds every few seconds.
The battery is almost flat.
►Charge the battery.
SmartCard reader is not recognised.
Cause Troubleshooting
Chip card inserted incorrectly. ►Make sure you have inserted your
SmartCard into the SmartCard reader
with the chip facing upwards/downwards
(device-dependent).
►Check whether the SmartCard you are using
is supported. Your SmartCard must comply
with the ISO standard 7816-1, -2, -3 and -4.
SmartCard PIN forgotten
Cause Troubleshooting
PIN forgotten ►If you are working in a network, contact your
system administrator, who can unlock your
notebook with a Supervisor PIN.
SmartCard lost
Cause Troubleshooting
SmartCard lost ►If you are working in a network, contact your
system administrator, who can boot up your
notebook with a Supervisor SmartCard.
80 Fujitsu
Troubleshooting and tips
Error messages on the screen
Errormessages on thes creenErrormessage:
This section describes the error messages generated by the BIOS Setup. Error messages displayed
by the operating system or programmes are described in the relevant documentation.
If the error message appears repeatedly, despite troubleshooting measures, please
contact the place of purchase or our customer service centre.
Error message/cause Resolution
CMOS battery bad
If the error message occurs repeatedly, the
buffer battery in the notebook is flat.
►Contact your sales outlet or our customer
service centre.
System CMOS checksum bad - default configuration
used
The system configuration information is
incorrect.
►Switch the notebook off.
►Switch the notebook on.
►Press the function key F2 to access the
BIOS Setup.
►In the BIOS Setup, select the Exit menu.
►Select the entry Load Setup Defaults.
►Select OK and press the Enter key.
Extended memory failed at offset: xxxx Failing Bits:
zzzz zzzz
When testing the extended memory an error has
resulted at the address xxxx.
►Check whether the additional memory
module has been inserted correctly.
Failure Fixed Disk n
The settings of the hard disk drive are incorrect.
►Start the BIOS Setup (Primary Master
submenu) and select the correct settings.
Keyboard controller error ►Switch the notebook off with the ON/OFF
switch.
►Wait 3 - 5 seconds and switch on the
notebook again.
Keyboard error If you are using an external keyboard:
►Check the connection and reboot the
notebook.
nn Stuck key ►Make sure that no key is pressed.
Operating system not found ►Check in the BIOS Setup whether your hard
disk has been set correctly.
►Make sure that the operating system is
installed on the corresponding drive.
Press <F1> to resume, <F2> to SETUP
This error message appears if an error occurs
during the self-test before starting the operating
system.
►Press the F1 function key to start the
operating system.
►Press the function key F2 to access the
BIOS Setup.
Fujitsu 81
Troubleshooting and tips
Error message/cause Resolution
Previous boot incomplete - Default configuration
used Due to an error during the previous system
boot, default values were used for certain
settings. Check the settings in the BIOS Setup.
►Press the F1 function key when prompted
to do so.
Real time clock error ►Contact your sales outlet or our customer
service centre.
nnnnK Shadow RAM failed at offset: xxxx Failing
Bits: zzzz
►Contact your sales outlet or our customer
service centre.
System battery is dead - Replace and run SETUP ►Contact your sales outlet or our customer
service centre.
System cache error - Cache disabled ►Contact your sales outlet or our customer
service centre.
System timer error ►Contact your sales outlet or our customer
service centre.
82 Fujitsu
Technical data
Technical data
Technicaldata
LIFEBOOK
Technicaldata
LIFEBOOK E546: LIFEBOOK E556:
Ambient conditions
Operating
temperature
5°C–35°C
Temperature in transit -15 ℃... 60 ℃
Dimensions
Width x depth x height 338 mm x 231 mm x 25.1 - 31.4 mm 374 mm x 250 mm x 24.2 -
31.4 mm
Weight approx. 1.9 kg approx. 2.1 kg
Main memory
Slots 2 slots 260 pin DDR4 - 2133 SO-DIMM with a total of max. 32 GByte
Approved memory
modules
4 GByte, 8 GByte or 16 GByte DDR4 - 2133 SO-DIMM
The data sheet for the device provides further technical data. You will find the data
sheet on your device or on the Internet at "http://www.fujitsu.com/fts/support/".
Rechargeable battery
You can find information on the batteries used in your device on the
Internet at "http://www.fujitsu.com/fts/support/".
Rechargeable
battery49Wh
Rechargeable
battery63Wh
Rechargeable battery
72 Wh
Rated voltage 10.8 V 10.8 V / 11.1 V 10.8 V / 11.25 V
Rated capacity 4500 mAh 5800 mAh / 5600 mAh 6700 mAh / 6400 mAh
Fujitsu 83
Technical data
Mains adapter
Technicaldata
Electrical data
Primary 65 W / 80 W / 90 W
Rated voltage 100 V – 240 V (automatic)
Rated frequency 50 Hz – 60 Hz (automatic)
Secondary
Rated voltage 19 V
Max. rated current 3.42 A / 4.22 A / 4.74 A
An additional mains adapter or power cable can be ordered at any time.
84 Fujitsu
Manufacturer’s notes
Manufacturer’s notes
Disposal and recycling
Notes
You can find information on this subject on your notebook or on our website
("http://www.fujitsu.com/fts/about/fts/environment-care/").
Declarations of Conformity
Declarationof conformity
The "Declarations of Conformity" for the device can be found on the Internet at:
"http://globalsp.ts.fujitsu.com/sites/certificates/default.aspx".
Fujitsu Technology Solutions hereby declares that your device is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC.
CE marking
CEmarkingCEmarkingNotesElectromagneticcompatibilityLowvoltagedi rective
The shipped version of this device complies with the requirements of EU directives 2004/108/EC
"Electromagnetic compatibility", 2006/95/EC "Low voltage directive", 2011/65/EC "RoHS directive"
and 2009/125/EC "ecodesign directive".
CE marking for devices with radio component
This equipment complies with the requirements of Directive 1999/5/EC of the European Parliament
and Commission from 9 March, 1999 governing Radio and Telecommunications Equipment
and mutual recognition of conformity.
CE nnnn (!) ; nnnn: For digits and exclamation mark (!), see label on the product.
The product complies with the legal limits for SAR in the EU.
You can find more information and declarations of conformity on the Internet at:
"http://globalsp.ts.fujitsu.com/sites/certificates".
This equipment can be used in the following countries:
Belgium Bulgaria Denmark Germany
Estonia Finland France Greece
UK Ireland Iceland Italy
Latvia Liechtenstein Lithuania Luxembourg
Malta Netherlands Norway Austria
Poland Portugal Rumania Sweden
Switzerland Slovakia Slovenia Spain
Czech Republic Hungary Cyprus Croatia
Turkey
Limitation in France: The use of WLAN in the 5 GHz band is not permitted outdoors.
Contact the corresponding government office in the respective country for current information on
possible operating restrictions. If your country is not included in the list, then please contact
the corresponding supervisory authority as to whether the use of this product is permitted in
your country.
Fujitsu 85
Manufacturer’s notes
The CE conformity declaration covers accessories (e.g., AC adapters, batteries, cable adapters)
and software (e.g., module drivers, module firmware and operating system). The software used and
affecting compliance is purchased by the module vendors and under solely control of those.
Radio frequencies used
RF module Frequency band Max. transmission power
1BT 2400-2480 MHz 100 mW
2WLAN 2410-2480 MHz 100 mW
3WLAN 5150-5350 MHz class 2 200 mW
4WLAN 5470-5725 MHz class 1 1 W
5GSM 850 MHz, 900 MHz 2 W
6UMTS 1900 MHz, 1800 MHz 500 mW
7LTE 2100 MHz, 2600 MHz 500 mW
8LTE 850 MHz, 900 MHz 2 W
86 Fujitsu
Index
Index
A
A beep sounds every second 76
Acoustic error messages 80
Alt + Tab 26
Anti-theft protection 52
Application keys 27
Audio devices, connecting 63
Audio ports 63
B
Back tab 26
Backspace 23
Bass loudspeaker (subwoofer) 41
Battery
battery life 31
caring for and maintaining 31
charge level 31, 39
charging 31
self-discharge 31
storage 31
Battery indicator 20
Battery status indicator
see Battery indicator 20
Battery status meter 31
Battery symbol
see Battery indicator 20
BIOS Setup Utility
calling 72
exiting 74
operating 73
protecting with password 53
settings 72
Bluetooth, safety notes 13
Board 64
Buffer battery, load 76
Buttons 22
C
Caps Lock 23
indicator 20
CD/DVD indicator 36
CD/DVD:
manual emergency removal 37
CE marking 85
Charging capacity, battery 31
Cleaning 15
Components
installing / removing 64
Configuration, BIOS Setup Utility 72
Connecting audio devices 63
Connecting headphones 63
Crystal View display
cleaning 15
Ctrl+Alt+Del 26
Cursor control keys 23
Cursor keys 23
D
Date is incorrect 76
Declaration of conformity 85
Device
setting up 17
Device drivers,
Serial port 59
Devices
Connecting 59
Drive
indicator 20
Removing 34
E
Electromagnetic compatibility 85
Emergency removal of data carrier 37
Energy
energy saving 14
Energy saving 14
Energy saving mode
leaving 79
Enter 23
Enter key 23
Error message:
on the screen 81
Error messages on the screen 81
Errors
Acoustic warnings 80
ESD 64
Ethernet LAN 46
External devices
Connecting 59
F
Fault
correction 75
Fingerprint sensor 51
configure 51
First-time setup 16
Fn key 23
Fn+F10 26
Fn+F3 25
Fujitsu 87
Index
Fn+F4 25
Fn+F6 26
Fn+F7 26
Fn+F8 26
Fn+F9 26
G
Getting started 16
H
Handling
data carriers 35
Hard disk:
restoring the contents 76
Hardware configuration 72
I
Important notes 13
Incorrect date/time 76
Indicator
Caps Lock 20
drive 20
Num Lock 20
Scroll Lock 20
Inserting
a data carrier 36
K
Key combinations 25
Keyboard 22
cleaning 15
L
LCD screen
cleaning 15
decrease brightness 26
difficult to read 77
notes 29
reflected glare 77
remains blank 77
LCD screen is too dark 77
Life, battery 31
Line feed 23
Loudspeakers 41
switch off 25
switch on 25
Low voltage directive 85
M
Main memory
see Adding memory 65
Mains adapter
connecting 17
setting up 17
Manual removal of data carrier 37
Mechanical backup 52
Memory card
handling 40
inserting 40
removing 40
Memory expansion
installing 67
removing 66
Memory module
important notes 65
installing 67
removing 66
Microphone 41
Microphone, connecting 63
Mobile operation 14
Module
Removing 34
Module bay 34
Modules 34
Monitor
connecting 58
drifting display 78
remains blank 77
Monitor port
see VGA connection socket 58
N
Notebook
before you travel 14
cannot be started 78
cleaning 15
stops working 79
switching off 21
transporting 14–15
using 19
Notebook, operation 19
Notes 13
boards 64
CE marking 85
cleaning 15
disposal / recycling 85
energy saving 14
LCD screen 29
Safety 13
transport 14
Num Lock
indicator 20, 24–25
88 Fujitsu
Index
Numeric keypad 22
see Separate numeric keypad 25
see Virtual numeric keypad 24
O
Operating system
activating system protection 54
cancel system protection 54
protecting with password 54
Operating system, restoring 76
Optical drive 35
P
Packaging 16
Password
changing 53
entering 53
removing 54
Password protection 52
Port Replicator
Connecting a notebook 48
Ports 47
Ports
Port Replicator 47
Power
power consumption 39
power-management features 39
Power-on indicator 20
Preparing for operation 17
Printer does not print 79
R
Radio component:
safety notes 13
Rechargeable battery 31
see Battery 31
Removing
a data carrier 36
Removing memory
see Adding memory 65
Return 23
S
Safety notes 13
Screen
no screen display 78
Screen brightness
decrease 26
increase 26
Scroll Lock
indicator 20
Security functions 51
SystemLock 56
Security functions,
SmartCard 56
Security Lock 52
Selecting a location 17
Self-discharge, battery 31
Separate numeric keypad 25
Serial port 59
Connecting devices 59
Serial port,
Settings 59
Servicing 64
Setup
see BIOS Setup Utility 72
Shift 23
Shift + Tab 26
Shift key 23
Slot
Memory cards 40
Standby indicator 20
Status indicators 19
Supervisor password
changing 53
entering 53
removing 54
Switching on
the notebook 21
Switchingonforthefirst time 18
System configuration 72
System expansion 65
see Adding memory 65
System settings, BIOS Setup Utility 72
T
Tab key 23
Technical data 83
Mains adapter 84
notebook 83
The radio connection to a network does
not work 79
Time not correct 76
Tips 75
Toggle output screen 26
Touchpad 25, 28
buttons 28
cleaning 15
dragging items 29
executing commands 28
moving the pointer 28
selectinganitem 28
switch off 25
Touchpad buttons 25
Fujitsu 89
Index
TPM 55
Transport
Transport damage 16
Transportation 14–15
Travel, notebook 14
Troubleshooting 75
Trusted Platform Module 55
U
USB charging function 61
USB ports 60
User password
changing 53
entering 53
removing 54
Using the Kensington Lock Cable 52
V
VGA connection socket 58
Virtual numeric keypad 24
Volume
decrease 26
increase 26
Volume control 41
W
Webcam 30
Weight Saver
Removing 34
Windows key 23
Wireless LAN:
safety notes 13
90 Fujitsu