FUJITSU LIFEBOOK T904
Contents
Fujitsu Contact Information
Notational conventions
Ports and controls
Important notes
First-time setup of your device
Working with the notebook
Security functions
Connecting external devices
Removing and installing components during servicing
Settings in BIOS Setup Utility
Troubleshooting and tips
Technical data
Manufacturer’s notes
Appendix
Index

Fujitsu T904 User Manual

Displayed below is the user manual for T904 by Fujitsu which is a product in the Notebooks category. This manual has pages.

Related Manuals

Fujitsu T904 Manual

System

Operating Manual

FUJITSU LIFEBOOK T904

Contact address in North America

FUJITSU AMERICA INC:

1250 East Arques Avenue Sunnyvale

CA 94085-3470, U.S.A.

Telephone: 800 831 3183 or 408 746 6000

"http://solutions.us.fujitsu.com"

"http://solutions.us.fujitsu.com/contact"

Have a question? Email us at: "AskFujitsu@us.fujitsu.com"

B5FK-2451-01ENZ0

FUJITSU LIFEBOOK T904

Operating Manual

Fujitsu Contact Information 7

Notational conventions 8

Ports and controls 9

Important notes 12

First-time setup of your device 17

Working with the notebook 21

Security functions 63

Connecting external devices 72

Removing and installing components

during servicing 78

Settings in BIOS Setup Utility 79

Troubleshooting and tips 81

Technical data 90

Manufacturer’s notes 95

Appendix 101

Index 117

Fujitsu America, Incorporated has made every effort to ensure the accuracy and completeness

of this document; however, as ongoing development efforts are continually improving the

capabilities of our products, we cannot guarantee the accuracy of the contents of this

document. We disclaim liability for errors, omissions, or future changes.

Fujitsu, the Fujitsu logo and LIFEBOOK are registered trademarks of Fujitsu Limited

or its subsidiaries in the United States and other countries.

Intel and Intel Core are trademarks or registered trademarks of Intel Corporation or

its subsidiaries in the United States and other countries.

Microsoft and Windows are either registered trademarks or trademarks of Microsoft

Corporation in the United States and/or other countries.

The ExpressCard word mark and logo are owned by the Personal Computer

Memory Card International Association (PCMCIA) and any use of such marks by

Fujitsu America, Incorporated is under license.

Google is a trademark or registered trademark of Google Incorporated.

Bluetooth is a trademark of Bluetooth SIG, Inc., USA.

OmniPass is a trademark of Softex, Inc.

Roxio is a trademark of Roxio, a division of Sonic Solutions.

PowerDirector, PowerDVD, YouCam, and MakeDisc are trademarks of CyberLink Corp.

Adobe, Acrobat, and Adobe Reader are either a reg istered trademarks or trademarks of

Adobe Systems Incorporated in the United States and/or other countries.

Made under license from DTS Licensing Limited. DTS and the symbol are registered trademarks and

The DVD player found in some models of the LIFEBOOK notebook incorporates copyright

protection technology that is protected by method claims of certain U.S. patents and other

intellectual property rights owned by Macrovision Corporation and other rights users. Use

of this copyright protection technology must be authorized by Macrovision Corporation, and

is intended for home and other limited viewing uses only unless authorized by Macrovision

Corporation. Reverse engineering or disassembly is prohibited.

All other trademarks speciﬁed here are the property of their respective owners.

Contents

FujitsuContact Information ............................................................ 7

Notationalconventions ................................................................ 8

Portsandcontrols ..................................................................... 9

Important notes ........................................................................ 12

Safetyinstructions ...................................................................... 12

Additional safety notes for devices with radio components . . . . . ............................. 13

Energysaving .......................................................................... 13

Energy saving under Windows ....................................................... 13

Traveling with your notebook . . ........................................................... 14

Before youtravel ................................................................... 14

Transporting the Tablet PC ........................................................... 15

Storing your TabletPC .................................................................. 15

Cleaning the TabletPC .................................................................. 16

Further informationon cleaningthe TabletPC ......................................... 16

First-timesetup ofyour device ......................................................... 17

Unpacking and checking the device . . . ................................................... 17

Choose a location . ...................................................................... 18

Connecting the AC adapter . . . ........................................................... 18

Switching on the device for the ﬁrsttime .................................................. 19

Installing Bonus Apps . . . . . ........................................................... 20

Working with thenotebook ............................................................ 21

Status indicators ........................................................................ 21

Opening the notebook ................................................................... 23

Switching the notebook on . . . . ........................................................... 24

Programing theON/OFF button ...................................................... 24

Different ways to use your notebook . . . ................................................... 25

From notebooktoTablet PC ......................................................... 25

Select display orientation (portraitor landscapeformat) ................................. 27

From TabletPC tonotebook .......................................................... 28

Switching off the notebook . . . . ........................................................... 29

Closing the notebook . . .................................................................. 30

Handwriting recognition .................................................................. 30

LCD screen ............................................................................ 31

Ambient light sensor ................................................................. 31

Using a deviceasatablet PC ............................................................ 32

Using your ﬁngers ................................................................... 32

Using the stylus ..................................................................... 35

Using the device asanotebook .......................................................... 39

Clickpadand Clickpadbuttons ....................................................... 39

Keyboard ............................................................................... 41

Virtualnumberkeys ................................................................. 43

Countryandkeyboard settings ....................................................... 43

Key combinations ................................................................... 44

Tablet buttons .......................................................................... 46

Webcam ............................................................................... 47

Rechargeablebattery ................................................................... 48

Charging,caring forand maintainingthebattery ....................................... 48

Fujitsu 3

Contents

Removing and installing thebattery ................................................... 48

Usingthe energy saving functions ........................................................ 52

Memorycards .......................................................................... 53

Supported format .................................................................... 53

Inserting thememorycard ........................................................... 53

Removing thememory card .......................................................... 53

Speaker and microphone ................................................................ 54

SIM card ............................................................................... 54

Inserting aSIM card ................................................................. 54

Removing a SIM card ............................................................... 55

Optional wireless LAN/Bluetooth/4G radio components . . . .................................. 55

Switching the wireless components on and off ......................................... 55

Setting up WLANaccess ............................................................ 56

Furtherinformation on WLANand Bluetooth ........................................... 56

Accessvia 4G ...................................................................... 56

Ethernet andLAN ....................................................................... 57

Your port replicator (optional) ............................................................ 58

Portsontheport replicator ........................................................... 58

Setting up theportreplicator ......................................................... 59

Connecting the notebook to the port replicator ......................................... 60

Switching on the notebook via the port replicator . . . . . .................................. 61

Switching offnotebookvia port replicator .............................................. 61

Disconnecting the notebook from the port replicator . . .................................. 62

Security functions ..................................................................... 63

Briefoverview ofthe securityfunctions .................................................... 64

Conﬁguring the ﬁngerprint sensor ........................................................ 65

Usingthe SecurityLock ................................................................. 65

Conﬁguringpasswordprotectionin BIOSSetupUtility ...................................... 66

Protecting BIOS Setup Utility (supervisor HDD password and user HDD password) . . . .... 66

Password protection for booting the operating system .................................. 67

Passwordprotectionfor the harddisk ................................................. 68

SmartCard reader ....................................................................... 69

Inserting theSmartCard ............................................................. 69

Usingthe securityfunction ofthe tablet buttons ............................................ 69

Assigning thesupervisorpassword ................................................... 69

Assigning theuserpassword ......................................................... 70

Entering passwordsvia thetabletbuttons ............................................. 70

Trusted Platform Module - TPM (device dependent) . . . . . . .................................. 71

Enabling TPM ....................................................................... 71

Disabling TPM ...................................................................... 71

Connecting externaldevices ........................................................... 72

HDMI port .............................................................................. 73

Connecting an external monitor to the port replicator . . . . . .................................. 74

Connecting USB devices ................................................................ 75

USB portwithcharging function (AnytimeUSB charge) ................................. 76

How toremove USBdevicescorrectly ................................................ 76

Headphones port ....................................................................... 77

Removing and installing components during servicing . . . .............................. 78

Settings in BIOS Setup Utility . . ........................................................ 79

Starting theBIOS Setup Utility ........................................................... 79

4Fujitsu

Contents

BIOS Setup Utilityoperation ............................................................. 79

Exiting BIOSSetup Utility ................................................................ 80

Exit Saving Changes - save changes and exit BIOS Setup Utility . . ..................... 80

Exit Discarding Changes - Reject changes and exit BIOS Setup Utility . . . . . .............. 80

Load Setup Defaults – load default values . ............................................ 80

Discard Changes - Discard Changes without exiting BIOS Setup Utility . . . . .............. 80

Save Changes - save changes without exiting the BIOS Setup Utility . . . . . . .............. 80

Save changesand poweroff ........................................................ 80

Troubleshootingand tips .............................................................. 81

Help ifproblems occur ................................................................... 81

Recovering yourFactory Image .......................................................... 81

The notebook’s date or time is incorrect ................................................... 82

Battery indicator does not illuminate . . . ................................................... 82

When certaincharacters areentered onthekeyboard,only numeralsare written ............. 82

The notebook’s LCD screen remains blank . . . . ............................................ 82

The LCD screen of the notebook is difﬁcultto read ......................................... 83

The externalmonitorremains blank ...................................................... 83

The externalmonitoris blank orthe imageis unstable ..................................... 83

The cursor does not correctly follow the stylus movements . . . . ............................. 84

Stylusinputnot working ................................................................. 84

The notebook does not start after switching it on . . . ........................................ 84

The notebook stops working . . ........................................................... 85

The printer does not print . . . . . ........................................................... 85

The wireless connection to a network does not work . . . .................................... 85

The battery discharges tooquickly ........................................................ 86

SmartCard reader is not recognized . . . ................................................... 86

SmartCard PINforgotten ................................................................ 86

SmartCard lost ......................................................................... 86

User and/or supervisor SmartCard lost ................................................... 87

Acoustic warning ........................................................................ 87

Errormessageson thescreen ........................................................... 88

Technicaldata ......................................................................... 90

Notebook . . ............................................................................. 90

WLAN speciﬁcations .................................................................... 92

Port replicator (optional) . . . . . . ........................................................... 93

Rechargeablebattery ................................................................... 93

AC adapter for use with notebook and port replicator . . . .................................... 94

Manufacturer’snotes .................................................................. 95

Disposal andrecycling .................................................................. 95

Recycling your battery ............................................................... 95

DOC (IndustryCANADA)Notices ........................................................ 95

UL Notice ........................................................................... 96

ENERGY STAR Compliance ............................................................. 97

Declarationsof Conformity ............................................................... 97

FCC andICRegulatoryInformation ...................................................... 98

Regulatory Notes and Statements . ................................................... 98

Appendix .............................................................................. 101

Before Using the Optional Wireless LAN . . . . . . ............................................ 101

Wireless LANDevicesCoveredby this Document ...................................... 101

Characteristicsof theWLAN Device .................................................. 101

Fujitsu 5

Contents

Wireless LAN Modes Using this Device . . ............................................. 102

Deactivating/DisconnectingtheWLAN Device ......................................... 104

Conﬁguringthe WirelessLAN ............................................................ 104

Conﬁguring the WLAN Using Windows . . . ............................................. 104

Connection to the network . . . ........................................................ 104

Troubleshooting the WLAN ........................................................... 105

Usingthe BluetoothDevice .............................................................. 107

Image Backup and Recovery Procedures ................................................. 108

Creating a Backup ofBootable Diskand RecoveryImage .............................. 108

RECOVERYOUR SYSTEMWHENTHE HARDDRIVE ISSTILLACCESSIBLE ............. 109

Usingthe Recovery andUtility Tools .................................................. 109

Restore the Recovery Image from Hidden Partition . . . .................................. 111

RECOVERYOUR SYSTEMWHENTHE HARDDRIVE ISNOT BOOTABLE ................ 112

RestoretheRecoveryImagefor FullHardDrive ....................................... 112

Recovering Your Recovery Image Using Recovery and Utility (for new hard drive or

non-bootableharddrive) ............................................................. 113

Installingthe Softwareafterthe RecoveryImage isRestored ............................ 114

Index .................................................................................. 117

6Fujitsu

Fujitsu Contact Information

Service and Support

You can contact Fujitsu Service and Support in the following ways:

• Toll free phone: 1-800-Fujitsu (1-800-838-5487)

• Website: "http://solutions.us.fujitsu.com/www/content/support/contact/index.php"

Before you place the call, have the following information ready so that the customer

support representative can provide you with the fastest possible solution:

• Product name

• Product conﬁguration number

• Product serial number

• Purchase date

• Conditions under which the problem occurred

• Any error messages that have occurred

• Type of device connected, if any

Fujitsu Shopping Online

Please go to "http://www.shopfujitsu.com/store/ ".

Maintaining Latest Conﬁguration

To ensure that you always have the most current driver updates related to your system, occasionally

access the Fujitsu Software Download Manager (FSDM) utility. The FSDM utility is available from

the Fujitsu Support site. FSDM will allow you to view a list of the most current drivers, utilities,

and applications to determine whether you have the latest versions. If you have a Windows 7

or Windows 8/8.1 operating system, you will need to go to the Support Site to download the

FSDM Utility: "http://support.fujitsupc.com/CS/Portal/support.do?srch=DOWNLOADS".

Limited Warranty

Your LIFEBOOK notebook is backed by a Fujitsu International Limited Warranty. Check the service

kit that came with your notebook for the Limited Warranty period and terms and conditions.

Fujitsu 7

Notational conventions

Pay particular attention to text marked with this symbol. Failure to observe

these warnings could pose a risk to health, damage the device or lead

to loss of data. The warranty will be invalidated if the device becomes

defective through failure to observe these warnings.

Indicates important information for the proper use of the device.

►Indicates an activity that must be performed.

Indicates a result.

This font Indicates data entered using the keyboard in a program dialog or at the

command line, e.g. your password (Name123)oracommandusedtostart

a program (start.exe)

This font Indicates information that is displayed on the screen by a program, e.g.:

Installation is complete.

This font Indicates

• terms and texts used in a software interface, e.g.: Click on Save

• names of programsorﬁles, e.g. Windows or setup.exe.

"This font" Indicates

• cross-references to another section, e.g. "Safety information"

• cross-references to an external source, e.g. a web address: For more

information, go to "http://solutions.us.fujitsu.com/"

• names of CDs, DVDs and titles or designations for other materials, e.g.:

"CD/DVD Drivers & Utilities" or "Safety/Regulations" manual

Key Indicates a key on the keyboard, e.g: F10 .

This font Indicates terms and texts that are emphasized or highlighted, e.g.: Do

not switch off the device.

8Fujitsu

Ports and controls

This chapter presents the individual hardware components of your device. It gives an

overview of the indicators and connections of the device. Please familiarize yourself

with these items before you start to work with the device.

Notebook open

123

1 = Microphone

2 = Webcam

3 = Webcam LED

4 = Windows button

5 = Ambient light sensor

6 = Clickpad

7 = Clickpad buttons

8 = Fingerprint sensor

Fujitsu 9

Ports and controls

Left-hand side

1 2 3 4 5 6

1 = DC jack (DC IN)

2 = Security Lock device

3 = USB port with charging function (Anytime

USB charge, USB 3.0)

4 = Memory card slot

5 = SmartCard reader

6 = Status indicators

Right-hand side

1 2 3 4 5 678

1 = Headphones port

2 = USB port 3.0

3 = HDMI port

4 = ON/OFF button

5 = Power-on indicator

6 = LAN connector (removable)

7 = Attachment eye for the stylus tether

8 = Stylus slot

10 Fujitsu

Ports and controls

Bottom

1 = Speakers

2 = Battery compartment with SIM card

slot under the battery

3 = Battery Lock slider switch

4 = Port for port replicator

Fujitsu 11

Important notes

ImportantnotesNotes

This chapter contains essential safety information which must be followed

when working with your notebook. Other notes also provide useful information

which will help you with your notebook.

Safety instructions

SafetyinformationInform ation,

Please observe the following safety information.

Please pay special attention to the sections in the manual marked

with the symbol on the left.

When connecting and disconnecting cables, observe the relevant

notes in this operating manual.

Read the information on the ambient conditions in the "Technical data", Page 90

chapter and the "First-time setup of your device", Page 17 chapter before preparing

your notebook for use and switching it on for the ﬁrst time.

When cleaning the device, please observe the relevant notes in the section .

Pay attention to the additional safety notes for devices with radio components

provided in the "Safety/Regulations" manual.

Please refer to the notes in the chapter "Removing and installing

components during servicing", Page 78.

When handling this device, you will come into contact with lead, a chemical which in

California is held to be a possible cause of birth defects and other damage to fertility.

Wash your hands after using the device.

This notebook complies with the relevant safety regulations for data processing equipment.

If you have any questions about setting up your notebook in the intended environment,

please contact your sales outlet or our Hotline/Service Desk.

12 Fujitsu

Important notes

Additional safety notes for devices with

radio components

Radiocomponent sWirelessLANBluetooth,Safetynotes

If a radio component (Wireless LAN, Bluetooth, 4G) is incorporated in your notebook, you

must be sure to observe the following safety notes when using your notebook:

• Switch off the radio components when you are in an aircraft or driving in a car.

• Switch off the radio components when you are in a hospital, an operating room or near a medical

electronics system. The transmitted radio waves can impair the operation of medical devices.

• Switch off the radio components, when you let the device get near ﬂammable gases

or into hazardous environments (e.g. gas station, paintshops), as the transmitted

radio waves can cause an explosion or a ﬁre.

For further information on how to switch the radio components on and off, refer

to chapter "Switching the wireless components on and off", Page 55.

Energy saving

NotesEnergyPowersaving

Switch the notebook off when it is not in use. Switch off any connected external devices when

they are not in use. If you use the energy saving functions, the notebook uses less power. You

will then be able to work for longer before having to recharge the battery.

The energy efﬁciency is increased and environmental pollution is reduced.

You save money and help protect the environment.

Energy saving under Windows

►Make use of the available energy saving functions as described in chapter

"Using the energy saving functions", Page 52.

Fujitsu 13

Important notes

Traveling with your notebook

MobileoperationNotesTrans portNotebook

Please observe the points listed below when traveling with your notebook.

Before you travel

►Back up important data stored on your hard disk.

NotebookTraveling,notebook

►Switch off the radio component for data security reasons. With data trafﬁc via a wireless

connection, it is also possible for unauthorized third parties to receive data.

Information on activating data encryption is provided in the documentation

for your radio component.

►If you wish to use your notebook during a ﬂight, check with the ﬂight attendants if its use is safe.

When traveling in other countries

►If you are traveling abroad, check that the AC adapter can be operated with the local AC

voltage. If this is not the case, obtain the appropriate AC adapter for your notebook.

Do not use any other converter!

►Check whether the local AC voltage and the AC cable are compatible. If this is not

the case, buy an AC cable that suits the local conditions.

►Enquire with the corresponding government ofﬁce of the country you will be traveling to,

whether you may use your notebook with its integrated radio component there.

►Take the necessary travel adapters with you when traveling abroad. Check the following

table to see which travel adapters you will need, or ask your travel organizer.

Power connection Travel destination

United States, Canada, Mexico, parts of Latin

America, Japan, Korea, Philippines, Taiwan

Russia and the Commonwealth of Independent

States (CIS), much of Europe, parts of Latin

America, the Middle East, parts of Africa, Hong

Kong, India, much of south-east Asia

United Kingdom, Ireland, Malaya, Singapore,

parts of Africa

China, Australia, New Zealand

14 Fujitsu

Important notes

Transporting the Tablet PC

Protect the Tablet PC from severe shocks and extreme temperatures

(e.g. direct sunlight in a car).

• Do not transport your Tablet PC while it is turned on.

• Carry your Tablet PC with you while traveling, rather than checking it in as baggage.

• Never put your Tablet PC through a metal detector; have it hand-inspected by

security personnel. You can however, put your Tablet PC through a properly

tuned X-ray machine. To avoid problems, place it close to the entrance of

the machine and remove it as soon as possible or have it hand-inspected

by security personnel. Security ofﬁcials may require you to turn your Tablet

PC on, so make sure you have a charged battery on hand.

►Switch the Tablet PC off.

►Unplug the AC plug of the AC adapter and all external devices from the power outlets.

►Disconnect the AC adapter cable and the data cables for all external devices.

►To protect the Tablet PC against damaging jolts and bumps, use a suitable Tablet

PC carrying case to transport your Tablet PC.

Storing your Tablet PC

• If storing your Tablet PC for a month or longer, turn it off, fully charge the battery,

then remove and store all Lithium Polymer batteries.

• Store your Tablet PC in a cool, dry location. Temperatures should remain

between 13ºF / -25ºC and 140ºF / 60ºC.

• Store your Tablet PC and batteries separately. If you store your Tablet PC with

a battery installed, the battery will discharge, and battery life will be reduced. In

addition, a faulty battery might damage your Tablet PC.

• Always power off the Tablet PC before transporting and/or packaging it.

After shutting down the Tablet PC, wait until the status led panel indicates

power off condition (i.e., no lights are illuminated).

• It is possible that the Tablet PC may not automatically go to power-off or hibernate

mode when you close the lid. This situation may occur due to pre-operating system

boot password security settings or some other application running on the Tablet PC.

• Attempting to transport the Tablet PC while power is on may damage

the Tablet PC due to shock or overheating.

Fujitsu 15

Important notes

Cleaning the Tablet PC

• Use of incorrect cleaners can result in optical impairment of the LCD and / or

damage to the computer. Always refer to the cleaner manufacturer’s guidelines and

material safety data sheets fo proper handling and use of the products.

• Never use ammonia, acidic, or alkaline cleaners or organic chemicals

such as paint thinner, acetone or kerosene. It may damage surface

ﬁnishes and the coating of the LCD screen.

• Never use compressed air for cleaning your computer.

• If your Tablet PC has a Smart Card slot, be very careful to avoid any

liquid entering the slot as this can damage the unit.

Further information on cleaning the Tablet PC

The Tablet PC does not ﬂoat.

If the Tablet PC is exposed to water or other liquids with its connections open, liquid

can penetrate the Tablet PC and cause a malfunction. Do not continue to use the

Tablet PC. Switch it off and contact our hotline / our service desk (see enclosed list of

service desks or visit our website at: "http://www.fujitsu.com/us/support/").

16 Fujitsu

First-time setup of your device

First- timese tupGettingstarted

Please read the chapter "Important notes", Page 12.

If your device is equipped with a Windows operating system, the necessary

hardware drivers and supplied software are already pre-installed.

Before switching it on for the ﬁrst time, connect the device to the AC voltage using

the AC adapter, see "Connecting the AC adapter", Page 18. The AC adapter must

remain connected during the whole of the installation process.

A system test is performed when your device is ﬁrst switched on. Various messages

can appear. The display may remain dark for a short time or may ﬂicker.

Please follow the instructions on the screen.

NEVER switch off your device during the ﬁrst-time setup process.

On delivery, the battery can be found in the battery compartment or in the accessories kit.

The battery must be charged if you want to operate your device using the battery.

When used on the move, the built-in battery provides the device with the necessary power. You

can increase the operating time by using the available energy saving functions.

For instructions on how to connect external devices (e.g. mouse, printer) to your

device, please refer to the operating manual for your device.

Unpacking and checking the device

If you ﬁnd that damage has occurred during transport, please notify

your local sales outlet immediately!

►Unpack all the individual parts.

PackagingTransport

►Check your device for any visible damage which may have occurred during transportation.

You may need to reuse the packaging in future, for example if you

need to transport your device.

Fujitsu 17

First-time setup of your device

Choose a location

ChoosealocationSetupACadapter

Choose a suitable location for the device before setting it up. In doing

so, please follow these instructions:

• Never place the device or the AC adapter on a heat-sensitive surface.

The surface could be damaged as a result.

• Never place the device on a soft surface (e.g. carpeting, upholstered furniture,

bed). This can block the air vents and cause overheating and damage.

• The underside of the device heats up during normal operation. Prolonged contact

with the skin can become unpleasant or even result in burns.

• Place the device on a stable, ﬂat, non-slippery surface. Please note that the

rubber feet of the device may mark certain types of delicate surfaces.

• Keep other objects at least 100 mm / 3.97 inches away from the device

and its AC adapter to ensure adequate ventilation.

• Never cover the ventilation openings of the device.

• Do not expose the device to extreme environmental conditions.

Protect the device against dust, humidity and heat.

Connecting the AC adapter

MakingreadytouseACadapter

Observe the safety notes in the enclosed "Safety/Regulations" manual.

The supplied AC cable conforms to the requirements of the country in which

you purchased your device. Make sure that the AC cable is approved for

use in the country in which you intend to use it.

►Connect the AC cable (1) to the AC adapter.

►Plug the AC cable (2) into a power outlet.

►Connect the AC adapter cable (3) to the

DC jack (DC IN) of the device.

18 Fujitsu

First-time setup of your device

Switching on the device for the ﬁrst time

Switchingonfortheﬁrstt ime

To make it easier to use your device for the ﬁrst time, the operating system

is pre-installed on the hard disk.

►Slide the ON/OFF button (1) to the right to switch on the notebook.

The ON/OFF button returns automatically to its original position.

►During the installation process, follow the on-screen instructions.

You can ﬁnd information and help on the Windows operating system functions

on the Internet at "http://windows.microsoft.com".

Fujitsu 19

First-time setup of your device

Installing Bonus Apps

After you have started your system the ﬁrst time, you will see a Bonus Apps icon on your desktop.

►Click on the icon to see which additional applications are available for you to install.

Applications that are already installed appear in grey, those that are

available for installation appear in blue.

►Select the applications you wish to install by selecting the checkbox adjacent to your selection.

►Click Select All if you would like to install all available applications

►To conﬁrm your selection click Install.

Note that in some cases (depending upon which application was selected for

installation) after installation completes, the system will prompt you to reboot.

There are also cases in which if multiple applications are selected to install

but one of them needs a reboot, the system will reboot and continue

installing the rest of the selected applications.

20 Fujitsu

Working with the notebook

Operation,notebo okNotebook

This chapter describes the basics for operating your notebook. Please refer to

"Connecting external devices", Page 72 for instructions on how to connect external

devices such as a mouse and a printer to the notebook.

Please refer to the notes in the chapter "Important notes", Page 12.

Status indicators

StatusindicatorsSymbols

The status indicators provide information about the status of the power supply,

the drives and the keyboard functions, etc.

Fujitsu 21

Working with the notebook

Status indicator Description

Num Lock indicator

The indicator is illuminated: The Num key has been pressed. The virtual

number keys have been activated. You can output the characters indicated

on the upper right of the keys.

Caps Lock indicator

The indicator is illuminated: The Caps Lock key has been pressed. All

characters are displayed in upper case. In the case of overlay keys, the

character printed on the upper left of the key will appear when that key is

pressed.

Scroll Lock indicator

The indicator is illuminated: The key combination FN +Rol has been

pressed. The effect that this key has varies between applications.

Power-on indicator

• The indicator is illuminated: The notebook is switched on.

• The indicator ﬂashes: The notebook is in sleep mode (Save-to-RAM).

• The indicator is not lit up: The notebook is switched off or the notebook is

in Save-to-Disk mode.

Battery charging indicator/AC connection

The charging state of the battery is shown by the rechargeable battery

indicator.

With AC adapter connected:

• The indicator lights up white: The battery is fully charged.

• The indicator light is orange: The battery is being charged.

• The indicator is ﬂashing orange: The AC adapter is connected but

the battery cannot be charged as the battery is too hot or too cold for

charging. The charging process is continued as soon as the battery has

reached a permissible temperature again.

• Indicator is off: The system is operating under battery power and the AC

adapter is not connected.

Battery indicator

The battery indicator shows the battery charge of the two installed batteries.

• The indicator lights up white: The battery is between 51% and 100%

charged.

• The indicator light is orange: The battery is between 13% and 50%

charged.

• The indicator lights up red: The battery is between 0% and 12% charged.

• The indicator is ﬂashing orange: The battery state of charge is being

checked (for four seconds after battery installation).

•Theindicatorisﬂashing red: The battery is faulty.

• The indicator is not lit up: There is no battery installed.

Drive indicator

The indicator is illuminated: The hard disk drive is being accessed.

Radio components indicator

• The indicator is illuminated: The radio components are switched on.

• Indicator is off: The radio components are switched off.

22 Fujitsu

Working with the notebook

Opening the notebook

►Fold the LCD screen upwards.

Fujitsu 23

Working with the notebook

Switching the notebook on

Notebook:sw itching onPower-onindicatorSuspend/Resumebutton

►Slide the ON/OFF button (1) to the right to switch on the notebook.

The ON/OFF button returns automatically to its original position.

The ON/OFF button (1) lights up whenever the system is switched on.

Programing the ON/OFF button

You can program the ON/OFF button:

Operating system Menu

Windows 7 Start - (Settings) - Control Panel - System and

Security - Power Options

Windows 8.1 Windows 8.1 Desktop - Control Panel - Hardware

and Sound - Power Options

If you have assigned a password, you must enter this when requested to

do so in order to start the operating system. Detailed information can be

found in the chapter "Security functions", Page 63.

24 Fujitsu

Working with the notebook

Different ways to use your notebook

During your daily work, you can use your notebook as a tablet PC or as a notebook, just as you wish.

You must note that the screen cannot be turned completely on its own axis!

Stop turning the screen when you feel resistance. No guarantee claims

can be met for damage caused by wrong turning.

From notebook to Tablet PC

►Raise the LCD screen into a vertical position.

Fujitsu 25

Working with the notebook

►Hold the screen as low as possible on both sides. Turn the screen to the left

or right in the direction of the arrow. At ﬁrst you will feel some slight resistance,

then the screen will turn easily and without friction.

►Turn the screen further until it has turned 180° and the hinge latches in.

26 Fujitsu

Working with the notebook

►Now fold the screen down until the back of the screen is almost ﬂat on top of the keyboard.

The screen is now secured in the tablet position.

Select display orientation (portrait or landscape format)

Landscapeformat

Portraitformat

Displayorientation

You can choose to use either portrait or landscape format for the display.

Windows 7

You can change these settings in the Fujitsu menu or under Start -(Settings -)

Control Panel -Hardware and Sound -Display -Settings.

Windows 8.1

You can change these settings under Windows 8.1 Desktop - Control Panel -

Hardware and Sound - Windows Mobility Center / Rotate screen.

In the Fujitsu Tablet Controls settings, proﬁles are saved for operation

with different screen orientations. These proﬁles have preset standard

conﬁgurations that can be modiﬁed as desired.

These settings do not just affect the screen settings on the Tablet PC, but

also on external monitors that are connected.

Fujitsu 27

Working with the notebook

From Tablet PC to notebook

►Raise the LCD screen into a vertical position.

28 Fujitsu

Working with the notebook

You must note that the screen cannot be turned completely on its own axis!

Stop turning the screen when you feel resistance. No guarantee claims

can be met for damage caused by wrong turning.

►Hold the screen on both sides as far down as possible and then turn the

screen. It will turn easily and without resistance.

►Turn or move the screen further until it has turned 180° and the hinge latches in.

Switching off the notebook

Notebook

►Close all applications and then shut down your operating system (please

refer to the "Operating system manual").

►Slide the ON/OFF button towards the right.

The ON/OFF button returns automatically to its original position.

Fujitsu 29

Working with the notebook

Closing the notebook

►Fold the LCD screen onto the bottom part of the notebook so that it locks into place.

Handwriting recognition

For detailed information on handwriting recognition, see the documentation for your operating system.

At present, handwriting recognition under Windows 7 or Window 8.1 supports the following languages:

English, German, French, Italian, Japanese, Korean, Chinese (traditional and simpliﬁed), Dutch,

Portuguese, Spanish, Brazilian, Norwegian (Bokmål and Nynorsk), Swedish, Finnish, Danish,

Polish, Rumanian, Serbian (Cyrillic and Latin script), Catalan, Russian, Czech and Croatian.

Under Windows 8.1 you can set the required language under ControlPanel–

Time, Language and Region – Language.

30 Fujitsu

Working with the notebook

LCD screen

LCDscreenNotes

High-quality LCD screens (TFT) are installed in Fujitsu notebooks. For technical reasons,

these screens are manufactured for a speciﬁc resolution. An optimal, clear picture can

only be ensured in the resolution intended for the particular screen. A screen resolution

which differs from the speciﬁcation can result in an unclear picture.

The resolution of the screen of your notebook is optimally set at the factory.

Current production technology cannot guarantee an absolutely fault-free screen display. A few

isolated constantly lit or unlit pixels (picture elements) may be present. The maximum permitted

number of such faulty pixels is speciﬁed in the international standard ISO 9241-307 (Class II).

Example:

A screen with a resolution of 1280 x 800 has 1280 x 800 = 1024000 pixels. Each pixel consists of

three subpixels (red, green and blue), so there are almost 3 million subpixels in total. According to ISO

9241-307 (class II), a maximum of 2 light and 2 dark pixels and in addition 5 light or 10 dark subpixels

or an equivalent mix (1 light subpixel counts as 2 dark subpixels) are allowed to be defective.

At a resolution of 1600 x 900 = 1440000 pixels, a maximum of 3 light and 3 dark pixels

and in addition 7 light or 14 dark subpixels are allowed to be defective.

Pixel A pixel consists of 3 subpixels, normally red, green and

blue. A pixel is the smallest element that can be generated

by complete functionality of the display.

Subpixel A subpixel is a separately addressable internal structure

within a pixel that enhances the pixel function.

Cluster A cluster contains two or more defective pixels or

subpixels in a 5 x 5 pixel block.

Background lighting

LCD screens are operated with background lighting. The luminosity of the background

lighting can decrease during the period of use of the notebook. However, you can

set the brightness of your monitor individually.

Synchronizing the display on the LCD screen and an external monitor

For more information, please refer to Chapter "Key combinations", Page 44

under "Switching between screen output".

Ambient light sensor

If your notebook was shipped with a Windows operating system, the screen brightness is

regulated by the ambient light sensor and is dependent on the particular light conditions.

This results in optimum readability and longer battery life at the same time.

Fujitsu 31

Working with the notebook

Using a device as a tablet PC

You can execute commands as follows:

• using the stylus (supplied with your device).

• using your ﬁnger

Using your ﬁngers

You can execute certain commands by using your ﬁnger tip on the touchscreen of your device.

Alternatively, everything which you can select or activate using your ﬁnger

tip can also be selected or activated using the stylus.

Calibrating the Dual Digitizer for ﬁnger-based operation of the device

Please see the appropriate supplementary sheet for instructions on how to

calibrate your device to use Dual Digitizer Technology.

Please note: There are separate calibration programs available for calibrating

the stylus and for calibrating ﬁnger-based operation. In each case, use the

calibration tool described in the supplementary sheet. Do not use the calibration

tool for the stylus to calibrate ﬁnger-based operation.

32 Fujitsu

Working with the notebook

Actions with one ﬁnger

Action Description

Selecting objects (click with the left mouse

button)

►Tap once brieﬂy on the object with your

ﬁnger.

Starting programs (double-click with the left

mouse button)

►Use one ﬁnger to tap twice in quick

succession on the program symbol.

Moving objects/windows (while holding the left

mouse button pressed, drag & drop)

►Place a ﬁnger on the object/window,

keep your ﬁngertip pressed against

the touchscreen and move the desired

object/window.

Opening a context menu (click with the right

mouse button)

►Tap on the desired item with your ﬁnger.

Keep your ﬁngertip pressed against the

touchscreen.

The context menu appears.

Moving the cursor ►Position one ﬁnger on the touchscreen and

move the ﬁnger in the desired direction.

Fujitsu 33

Working with the notebook

Actions using two ﬁngers

Action Description

Scrolling

►Place two ﬁngers on the touchscreen.

►Move the ﬁngers up to scroll up.

►Move the ﬁngers down to scroll down.

Rotating

►Position your thumb on the touchscreen and

rotate the image clockwise or anticlockwise

using your index ﬁnger.

34 Fujitsu

Working with the notebook

Action Description

Increasing or decreasing view

►Place two ﬁngers on the touchscreen and

move them apart to increase the size of the

view.

►Place two ﬁngers on the touchscreen and

move them together to decrease the size

of the view.

Locking context-sensitive menus ►Use two ﬁngers to tap twice in quick

succession on the touch screen.

Using the stylus

Pen

1=stylusti

2 = stylus button (right mouse button)

3 = eyelet for stylus tether

Fujitsu 35

Working with the notebook

You can use the stylus on your Tablet PC as an electronic writing tool, to select menu items and to

navigate through the programs. Programs that support handwriting recognition also allow you to

write directly on the screen with the stylus. You can also use the stylus as a drawing tool.

The Tablet PC is supplied with a stylus tether which you can attach to the

eyelets on the stylus and on the Tablet PC.

Use only the stylus that was provided with your Tablet PC. Do not use any other pointed

object as a substitute, that was not specially designed for your Tablet PC. Replace

the stylus tip if it is worn. The warranty does not cover a scratched screen.

While writing, take care that you do not scratch the surface of the

display (e.g. with a wristwatch or bracelet).

The stylus of the Tablet PC is an electronic instrument that can be damaged

if used improperly. Handle the stylus with care.

Our recommendations for proper handling of the stylus are as follows:

• Do not gesture with the stylus.

• Do not use the stylus as a pointer.

• Do not use the stylus on surfaces other than the screen of the Tablet PC.

• Do not try to turn the grip of the stylus. The grip is used to put the

stylus into its slot and to take it out of its slot.

• Never store the stylus with its weight on the tip (e.g. with the tip down in a pen

container). If the stylus is stored with the tip pointing down, this may have an

adverse effect on the stylus mechanism (particularly under high temperatures). In

this case the stylus tip may react as though it is constantly being pressed down. To

avoid damage, the stylus should be stored in the stylus slot when not in use.

The stylus can be inﬂuenced by electromagnetic ﬁelds (cursor quivers or

jumps). There may be a few areas on the screen where the cursor quivers

slightly in spite of pressing the stylus down ﬁrmly.

The screen responds to entries made with the tip of the ﬁnger or the stylus when the

tip of the ﬁnger or the stylus directly touches the screen.

You can use the stylus to perform almost all functions for which you would otherwise use a mouse.

Delete functions are not supported by the stylus.

Action Mouse Stylus

Selecting menu

items

Click with the left mouse button. Tap on the menu entry with the tip of

the stylus.

Starting programs Double-click with the left mouse

button.

Tap on the program symbol twice in

rapid succession using the stylus tip.

Moving an object

or window

Drag with the left mouse button

pressed.

Place the stylus tip directly on the

object or window. Keep the stylus tip

held against the screen. Drag the

desired object or window.

36 Fujitsu

Working with the notebook

Opening a context

Click with the right mouse button. Tap on the desired element with the

stylus and keep the stylus pressed

against the screen.

Moving the cursor Move the mouse Place the tip of the stylus directly on

the screen.

Adjusting the stylus

Operating system Menu

Windows 7 Under Hardware and Sound - Pen and Input Devices, you can make various

settings for the stylus in the control panel (assignment and function of

the stylus button).

Windows 8.1 Under Windows 8.1 Desktop - Control Panel - Hardware and Sound - Pen and

Input Devices you can make various settings for the stylus (assignment

and function of the stylus button).

Calibrating the stylus

If Windows 8.1 is installed on your Tablet PC, your Tablet PC is already calibrated at initial setup.

If a different operating system is installed on your Tablet PC, you must calibrate it with the

stylus before ﬁrst use, so that it recognizes the stylus as accurately as possible.

You should also always repeat the calibration if the coordination between the

stylus and the cursor movement deteriorates.

Operating system Menu

Windows 7 /

Windows 8.1 Desktop

To calibrate, run the Hardware and Sound / Tablet PC Settings function in the

Control Panel. You need to calibrate both portrait and landscape formats.

Fujitsu 37

Working with the notebook

Securing a stylus tether

You can secure the stylus with a stylus tether to prevent accidentally dropping it or losing it.

►Secure the end of the stylus tether with the smaller loop to your stylus.

►Secure the end of the stylus tether with the larger loop to your notebook.

38 Fujitsu

Working with the notebook

Using the device as a notebook

Clickpad and Clickpad buttons

Keep the Clickpad clean. Protect it from dirt, liquids, and grease.

ClickpadClickpad

Do not use the Clickpad if your ﬁngers are dirty.

Do not rest heavy objects (e.g. books) on the Clickpad or the Clickpad buttons.

1 = Clickpad

2 = Clickpad buttons

The Clickpad enables you to move the mouse pointer on the screen.

The Clickpad buttons allow the selection and execution of commands. They

correspond to the buttons on a conventional mouse.

You can also deactivate the Clickpad via a keyboard shortcut, so that you cannot move

the pointer on the screen unintentionally (see chapter "Key combinations", Page 44).

Moving the pointer

►Move your ﬁnger on the Clickpad.

Clickpad

The pointer will move.

Selecting anitem

►Move the pointer to the item you wish to select.

Clickpad

►Tap the Clickpad once or press the left button once.

The item is selected.

Executing commands

►Move the pointer to the ﬁeld you wish to select.

Clickpad

►Ta p t h e Clickpad twice or press the left button twice.

The command is executed.

Fujitsu 39

Working with the notebook

Dragging items

►Select the desired item.

Clickpad

►Press and hold the left button and drag the item to the desired position

with the ﬁnger on the Clickpad.

The item will be moved.

Switching the Clickpad on and off

You can switch the Clickpad on and off using a key combination,

see "Key combinations", Page 44.

40 Fujitsu

Working with the notebook

Keyboard

KeyboardNumerickeypadNumberke ypadke ys

The keyboard of your notebook is subject to continuous wear through normal

use. The key markings are especially prone to wear. The key markings are

liable to wear away over the life of the notebook.

The keyboard has been designed to provide all the functions of an enhanced keyboard.

Some enhanced keyboard functions are mapped with key combinations.

The following description of the keys applies to the Windows operating system. Additional functions

supported by the keys are described in the relevant manuals supplied with your application programs.

The following illustration shows how to access the different characters on keys with overlaid

functions. The example applies when the Caps Lock key has not been activated.

The illustration may differ from your device variant.

}

Num

Alt Gr

Fujitsu 41

Working with the notebook

Key Description

Backspace key

The Backspace key deletes the character to the left of the cursor.

BackspacekeyBackspace

Tab key

The Tab key moves the cursor to the next tab stop.

Tabkey

Enter key (return)

The Enter key terminates a command line. The command you have entered

is executed when you press this key.

EnterkeyReturnEnterLine feed

Caps Lock

Caps Lock key

The Caps Lock key activates uppercase mode. In Caps Lock mode, all of

the characters you type appear in upper case. In the case of overlay keys,

the character printed on the upper left of the key will appear when that

key is pressed. To cancel the Caps Lock function, simply press the Caps

Lock key again.

CapsLockkeyCapsLock

Shift key

The Shift key causes uppercase characters to appear. In the case of overlay

keys, the character printed on the upper left of the key will appear when

thatkeyispres

sed.

ShiftkeyShift

Fn key

The Fn key enables the special functions indicated on overlay keys (see

"Key combinations", Page 44).

Fnkey

Cursor keys

The cursor keys move the cursor in the direction of the arrow, i.e. up, down,

left, or right.

CursorkeysCursorcontrol

Windows key

The Windows key switches between the start screen and the last used

application.

Windowskey

Menu key

The Menu key opens the menu for the active application.

42 Fujitsu

Working with the notebook

Virtual number keys

NumerickeypadVirtualnumberke ysNumLock

Virtual number keys are provided so that the keys of a number keypad can be used for certain

applications. The virtual number keys are recognizable on the keyboard by the numbers and

symbols printed in the upper right corner of each key. If you have switched on the virtual number

keys, you can output the characters shown on the upper right of the keys.

The key assignment shown below may be different from the keyboard

layout of your device variant.

456

123

<>?

789

456

123+

1 = Character valid when the Num

key is not active

2 = Character valid when the Num

keyisactive

Further information about the status indicators can be found in chapter "Status indicators", Page 21.

Country and keyboard settings

►Make the country and keyboard settings as described in the documentation for your operating

system.

Fujitsu 43

Working with the notebook

Key combinations

Keycombinations

The following description of key combinations applies to Windows operating systems. Some of the

following key combinations may not function in other operating systems or with certain device drivers.

Other key combinations are described in the relevant manuals supplied

with your application programs.

Key combinations are entered as follows:

►Press the ﬁrst key in the combination and keep it pressed.

►While holding the ﬁrst key down, press the other key or keys in the combination.

Combination Description

Activate/deactivate keyboard backlight

On backlit keyboards, this key combination activates or deactivates

the backlight.

Fn+F2ActivateDeactivate

Sequence:

• Background lighting off

• Low brightness

• High brightness

• Background lighting off

Switching the speakers on and off

This key combination switches your notebook’s speakers off and

on.

Fn+F3SwitchonSwitchoff

Activate/deactivate mouse and Clickpad buttons

This key combination switches the Clickpad and the Clickpad

buttons on or off.

Fn+F4ClickpadClickpadbuttonsClickpad

Wireless components

This key combination switches the wireless components off or on.

Fn+F5Wirel esscomponents

Decreasing the screen brightness

This key combination decreases the brightness of the screen.

Fn+F6LCD screenScreenbrightness

Increasing the screen brightness

This key combination increases the brightness of the screen.

Fn+F7Screenbri ghtness

Decrease the volume

This key combination reduces the volume of the internal speakers.

Fn+F8Vol ume

44 Fujitsu

Working with the notebook

Combination Description

Increase volume

This key combination increases the volume of the internal

speakers.

Fn+F9Vol ume

Switching between screen outputs

Use this key combination to select which screen(s) is/are used for

display if an external monitor is connected.

The screen output is possible in the following sequence:

• only on the notebook’s LCD screen

• on the LCD screen of the notebook and the external monitor

atthesametime

• only on the external monitor

This setting is useful if you would like a high resolution and a

high refresh rate on an external monitor.

Fn+F10Switchingbetweenscreenoutputs

Switch between open applications

Use this key combination to switch between several open

applications.

Alt+Tab

Switching over to Windows 8 Desktop (Windows 8 only)

With this key combination, you can switch from Windows 8 Modern

to Windows 8 Desktop.

Switching over to Windows 8 Desktop and minimizing

applications (Windows 8 only)

With this key combination, you can switch from Windows 8

Modern to Windows 8 Desktop and at the same time minimize

the applications.

AltCtrl Del

Windows security/Task-Manager

This key combination opens the Windows Security/Task Manager

window.

Ctrl+Alt+Del

Back tab

This key combination moves the cursor back to the previous tab

stop.

Shift+TabBacktab

Key combinations using the Windows keys are detailed in the manual

for your operating system.

Fujitsu 45

Working with the notebook

Tablet buttons

Your notebook is equipped with a Windows button and two volume buttons.

Button Function

Windows button

This button has the same function as the Windows Start key on the keyboard.

If the button is pressed in combination with the ON/OFF button, the function is the

same as for the Ctrl +Alt +Del key combination.

Increase volume

This button increases the volume of the internal speakers.

_Decrease the volume

This button decreases the volume of the internal speakers.

46 Fujitsu

Working with the notebook

Webcam

Depending on the software used, you can use your webcam to take pictures,

record video clips or take part in web chats.

The webcam has its own status indicator. The indicator lights up when the webcam is active.

• The picture quality depends on the lighting conditions and the software being used.

• You can only operate the webcam with a particular application (e.g. an Internet telephony

program or a video conferencing program which supports a webcam).

• When using the webcam, the notebook base must not wobble.

• The webcam automatically adjusts itself to the current light level. For this reason

the LCD display may ﬂicker while the light level is adjusted.

Further information on use of the webcam and additional settings for your webcam

can be found in the help function of the program using the webcam.

Fujitsu 47

Working with the notebook

Rechargeable battery

BatteryBatteryServicelife,batteryRechargeablebatteryBattery

During mobile use, the notebook runs on its built-in battery. You can increase the

service life of the battery by caring for the battery properly. The average battery

service life is around 800 charge/discharge cycles.

You can extend the battery service life by taking advantage of the available energy saving functions.

Charging, caring for and maintaining the battery

BatteryBattery

The notebook battery can only be charged if the ambient temperature is between

5°C / 41°F and a maximum of 35°C / 95°F.

You can charge the battery by connecting the notebook to the AC adapter

(see "Connecting the AC adapter", Page 18).

If the battery is running low you will hear a warning alarm. If you do not connect the AC adapter

within ﬁve minutes of the warning alarm described above, your notebook will automatically switch off.

Monitoring the battery state of charge

Batterybatterychargemeter

Windows also has a "Battery charge meter" in the taskbar for monitoring the

battery capacity. When you place the mouse pointer on the battery symbol, the

system displays the state of charge of the battery.

Battery storage

BatteryBatterySelf-discharge,batteryChargecapac ity,battery

The battery should be stored in a dry environment at a temperature between 0°C / 32°F and

30°C / 86°F. The lower the storage temperature, the lower the rate of self-discharge.

If you will be storing batteries for a longer period (more than two months),

the battery charge level should be approx. 30%. To prevent exhaustive

discharge which would permanently damage the battery, check the level

of charge of the battery at regular intervals.

To be able to make use of the optimum capacity of the battery, you should allow

the battery to fully discharge and then recharge it.

If you will not use batteries for long periods, remove them from the

notebook. Never store batteries in the device.

Removing and installing the battery

Only use batteries approved by Fujitsu for your notebook.

Never use force when ﬁtting or removing a battery.

Make sure that no foreign bodies get into the battery connections.

Never store a battery for longer periods in the discharged state. This

can make it impossible to recharge.

48 Fujitsu

Working with the notebook

Removing a battery

Please observe the safety information in chapter "Important notes", Page 12.

Remove the power plug from the power outlet!

►Switch the device off.

The device must not be in energy saving mode.

►Close the LCD screen.

►Remove all the cables from the device.

►Turn the device over and place it on a stable, ﬂat and clean surface. If necessary, lay an

anti-slip cloth on this surface to prevent the device from being scratched.

Fujitsu 49

Working with the notebook

►Slide the Battery Lock slider switch in the direction of the arrow (1) and hold it in place.

►Slide the Battery Lock slider switch in direction of the arrow (2).

►Remove the battery compartment cover (3).

►Remove the battery from the battery compartment (4).

50 Fujitsu

Working with the notebook

Installing a battery

►Insert the battery in the battery compartment (1).

►Close the battery compartment cover (2).

►Slide the Battery Lock slider switch in direction of the arrow (3).

The battery is secured.

►Turn the notebook the right way up again and place it on a ﬂat surface.

►Reconnect the cables that were previously disconnected.

Fujitsu 51

Working with the notebook

Using the energy saving functions

EnergyEnergyBattery

The notebook uses less power when the available energy-saving functions are used. You will

then be able to work longer when using the battery before having to recharge it.

The energy efﬁciency is increased and environmental pollution is reduced.

By choosing the best power options, you can make signiﬁcant savings and

at the same time help protect the environment.

When you fold down and close the LCD screen, depending on the setting in Windows,

the notebook automatically enters a power saving mode.

►Set the energy saving functions in your Control Panel.

►Set the screen saver in your Control Panel.

►Right-click on the desktop. Activate the screen saver by clicking on Personalize – Change

Screen Saver.

If you need further information about an option, you can get help with most

settings by pressing F1 to open the Microsoft Help.

When the notebook is in energy saving mode, the following must be remembered:

During energy saving mode, open data is held in main memory or

in a swap ﬁle on the hard disk.

Never switch the notebook off while it is in an energy saving mode. If the built-in battery

is nearly ﬂat, close all open ﬁles and do not go into energy saving mode.

If you do not intend to use your notebook for a long period of time:

►Exit energy saving mode if necessary by moving the mouse, making an entry at the keyboard

or by switching on the notebook.

►Close all opened programs and completely shut down the notebook.

52 Fujitsu

Working with the notebook

Memory cards

Slot

Your notebook is equipped with an integrated memory card reader.

Follow the manufacturer’s instructions when handling the memory cards.

Memorycard

Supported format

The memory card reader supports the following format:

• Secure Digital (SDTM Card)

• SDHC

•SDXC

Inserting the memory card

►Carefully slide the memory card into the

slot. The label should be facing upward. Do

not apply excessive force, as otherwise the

delicate contact surfaces could be damaged.

Memorycard

Depending on the particular type

used, the memory card may protrude

slightly from the slot.

Removing the memory card

Memorycard

To avoid any loss of data, always follow the correct procedure for removing the

card (see the documentation for your operating system).

►On devices with card locking: Press

on the memory card (1).

Memorycard

The memory card is released and

can now be removed.

►Pull the memory card out of the slot (2).

Fujitsu 53

Working with the notebook

Speaker and microphone

MicrophoneSpea kerSubwooferVolume con trol

You can ﬁnd information about the exact position of the speaker and microphone

in chapter "Ports and controls", Page 9.

Please refer to chapter "Key combinations", Page 44 for information on setting the volume

and also enabling/disabling the speakers using key combinations.

If you attach an external microphone, the built-in microphone is disabled.

When you connect headphones or external speakers, the built-in speakers are disabled.

You can ﬁnd information on connecting headphones and a microphone in

chapter "Connecting external devices", Page 72.

SIM card

A SIM Card (Subscriber Identity Module) is a chip card which is inserted in a mobile telephone or

notebook and, together with an integrated 4G module, enables access to a mobile radio network.

Follow the instructions supplied by the provider of the SIM card.

Inserting a SIM card

►Remove the battery, see Chapter "Removing a battery", Page 49.

►Slide the SIM card into the slot (1),

as shown in the battery compartment,

until you feel it engage.

►Install the battery again, see Chapter "Installing a battery", Page 51.

54 Fujitsu

Working with the notebook

Removing a SIM card

►Remove the battery, see Chapter "Removing a battery", Page 49.

►Press on the edge of the SIM card so that

it jumps up slightly out of the slot.

►Pull the SIM card out of the slot in the

direction of the arrow (1).

►Install the battery again, see Chapter "Installing a battery", Page 51.

Optional wireless LAN/Bluetooth/4G radio

components

The installation of radio components not approved by Fujitsu will invalidate

the certiﬁcations issued for this device.

Depending on the device conﬁguration you ordered, your device will be

equipped with wireless LAN, Bluetooth or 4G.

Switching the wireless components on and off

►Press the key combination Fn +F5 to start the WirelessSelector.

WirelessLAN

BluetoothBluetooth

The wireless component indicator will illuminate when one or more wireless

components are switched on.

The Bluetooth and 4G modules and the wireless LAN transmission unit (antenna)

will all be switched off when you switch off the wireless components.

Pay attention to the additional safety notes for devices with wireless

components provided in the "Safety" manual.

Details on using a wireless LAN can be found in the online help system

included in the wireless LAN software.

You can obtain more information on 4G from your service provider.

Fujitsu 55

Working with the notebook

Setting up WLAN access

• Requirement: A WLAN must be available and you must have the

corresponding access information.

Information on conﬁguring the WLAN access can be found in the

documentation for your operating system.

Further information on WLAN and Bluetooth

For further information about WLAN or Bluetooth, see the Appendix of this manual.

For WLAN speciﬁcations, see chapter "WLAN speciﬁcations", Page 92.

Access via 4G

You can purchase the accessories for 4G reception from your Fujitsu dealer.

If you have ordered a 4G module, your device will already be prepared when you receive it.

You will ﬁnd information on establishing the connection with the 4G network

in the documentation for the hardware you plan to use.

56 Fujitsu

Working with the notebook

Ethernet and LAN

EthernetLAN

You can use an Ethernet LAN when you use a LAN adapter, which can be obtained as an option.

You can use it to establish a connection to a local network (LAN = Local Area Network).

►Pull the LAN adapter out of the LAN port on

the notebook in the direction of the arrow.

►Push the LAN adapter upwards in the

direction of the arrow (1).

►Plug the network cable into the

LAN adapter (2).

►Connect the network cable to your

network port.

Your network administrator can help you to conﬁgure and use the LAN connections.

The network cable is not included in the delivery scope. This type of

cable can be obtained from a specialist dealer.

Fujitsu 57

Working with the notebook

Your port replicator (optional)

Your port replicator is a device that helps you to quickly connect your notebook to

your peripheral devices, such as a monitor, printer, etc.

The features offered by the port replicator include standard ports for

monitor, audio, mouse and keyboard.

You need only dock the notebook in order to work with your peripheral devices.

Ports on the port replicator

PortreplicatorPorts

345617

1=Securit

yLock

2 = USB ports

3=LANpo

4 = DisplayPort

5=DVIpo

6 = VGA monitor port

7 = DC input connector (DC IN)

8 = Connector on the port replicator for the

docking port on the bottom of the notebook

9 = Release

10 = ON/OFF button

58 Fujitsu

Working with the notebook

Setting up the port replicator

Select a suitable location for the port replicator before setting it up. In

doing so, please follow these instructions:

• Never place the port replicator on a soft surface (e.g. carpeting, upholstered furniture, bed).

This can block the air vents of the notebook and cause overheating and damage.

• Place the port replicator on a stable, ﬂat and anti-slip surface. Please note that

the rubber feet may mark certain types of surfaces.

• Never place the port replicator and the AC adapter on a heat-sensitive surface.

• Do not expose the port replicator to extreme environmental conditions.

Protect the port replicator from dust, humidity and heat.

Fujitsu 59

Working with the notebook

Connecting the notebook to the port replicator

►Disconnect the AC adapter cable from the DC jack (DC IN) of the notebook.

►Place the notebook on the port replicator so that the connector on the underside of

the notebook aligns with the connector on the Port Replicator (1).

►Press down on the notebook’s rear corners so that it locks into position (2).

►Connect the AC adapter cable to the DC jack (DC IN) of the Port Replicator (3).

►Connect the AC cable to the AC adapter (4).

►Plug the AC cable into the power outlet (5).

60 Fujitsu

Working with the notebook

Switching on the notebook via the port replicator

►Press the ON/OFF button on the port replicator to switch the notebook on.

Switching off notebook via port replicator

►Close all applications and then shut down your operating system (please

refer to the manual for the operating system).

If the notebook cannot be shut down properly, press the ON/OFF button on

the port replicator for approx. four seconds. The notebook will switch off.

However, any unsaved data may be lost in the process.

Fujitsu 61

Working with the notebook

Disconnecting the notebook from the port replicator

►Pull the unlocking lever in the direction of the arrow (1), until you hear the notebook unlatch.

►Lift off the notebook (2).

62 Fujitsu

Security functions

Securityfunctions

Your notebook has a variety of security functions that you can use to protect your

system and your personal data from unauthorized access.

This chapter explains how to use these functions, and what the beneﬁts are.

Please remember that in some cases, for example, forgetting your password,

you may be locked out of the system and unable to access your data.

Therefore, please note the following information:

• Make regular backups to external optical disks such as external hard

drives, CDs, DVDs or Blu-ray Discs.

• Some security functions need you to choose passwords. Make a note

of the passwords and keeptheminasafeplace.

If you forget your passwords you will need to contact our Service Desk.

Deletion or resetting of passwords are not covered by your warranty

and a charge will be made for assistance.

Fujitsu 63

Security functions

Brief overview of the security functions

Detailed information about the security equipment of your device can be found

in the "Professional Notebook" manual, on the "Drivers & Utilities" CD/DVD

or on our website at "http://www.fujitsu.com/us/support/".

Security function Type of protection Preparation

Security Lock Mechanical Fit and lock the Kensington

Lock Cable (accessory).

Fingerprint sensor (device

dependent)

Biometric Install the supplied ﬁngerprint

software.

BIOS password protection Password protection for

the BIOS Setup, operating

system and hard disk with

supervisor and user password.

The passwords consist of a

maximum of eight alphanumeric

characters.

Specify at least one supervisor

password in the BIOS Setup

and activate the password

protection for the operating

system and hard disk as

desired.

Boot from Removable Media Prevents unauthorized booting

of an operating system from

external media (e.g. USB stick,

USB CD-ROM drive, etc.).

In the BIOS Setup, go to the

Security menu and edit the Boot

from Removable Media option.

Owner Information Display service desk or owner

information during the boot

process.

In the BIOS Setup, go to the

Security menu and edit the

Owner Information option.

SmartCard reader (device

dependent)

PIN and SmartCard protection

for the operating system

To use the SmartCard reader

functions, install the supplied

(or other suitable) software.

Trusted Platform Module

(device dependent)

Identiﬁcation and authentication

of the notebook

Deﬁne a supervisor password

in the BIOS Setup and enable

the TPM (Security Chip).

64 Fujitsu

Security functions

Conﬁguring the ﬁngerprint sensor

Fingerprintsens orFinger printsensor

The ﬁngerprint sensor can record the image of a ﬁngerprint. With additional ﬁngerprint

software, this image can be processed and used instead of a password.

►Install the ﬁngerprint software to be able

to use the ﬁngerprint sensor (1).

Using the Security Lock

Your device comes with a Security Lock mechanism for the Kensington Lock Cable. You

can use the Kensington Lock Cable, a sturdy steel cable, to help protect your notebook

from theft. The Kensington Lock Cable is available as an accessory.

Fujitsu recommends the use of a combination lock.

►Fit the Kensington Lock Cable to the

mechanism on your notebook.

KensingtonLoc kCabl eUsingt hese curity loc kMec hanicalsecurit yAn ti-theftprotection

Attach another Kensington Lock Cable to your port replicator to protect your port

replicator from theft as well. There are two security lock devices on your port replicator.

Fujitsu 65

Security functions

Conﬁguring password protection in BIOS Setup Utility

Before using the various options for password protection in the BIOS Setup

Utility, please proceed as follows to increase data security:

Make a note of the passwords and keep them in a safe place. If you forget your

supervisor HDD password you will not be able to access your notebook. Passwords

are not covered by your warranty and a charge will be made for assistance.

Password prote ction

Your password can be up to eight characters long and can contain letters and

numbers. No distinction is made between uppercase and lowercase.

Protecting BIOS Setup Utility (supervisor HDD password

and user HDD password)

If you have opened these operating instructions on the screen, we recommend

that you print them out. You cannot call up the instructions on the screen

while you are setting up the password.

BIOSSetupUtility

The supervisor HDD password and the user HDD password both prevent unauthorized use of the

BIOS Setup Utility. The supervisor HDD password allows you to access all of the functions of the BIOS

Setup Utility, while the user HDD password will only give you access to some of the functions. You

can only set a user HDD password when a supervisor HDD password has already been assigned.

Calling and using the BIOS Setup Utility is described in the chapter

"Settings in BIOS Setup Utility", Page 79.

Assigning the supervisor and user HDD passwords

►Start the BIOS Setup Utility and go to the Security menu.

►Select the Set Supervisor Password ﬁeld and press the Enter key.

With Enter new Password: you are asked to enter a password.

►Enter the password and press the Enter key.

Conﬁrm new Password requires you to conﬁrm the password.

►Enter the password again and press the Enter key.

Changes have been saved is displayed as a conﬁrmation that the new password has been saved.

►To set the user HDD password, select Set User Password and proceed exactly

as when conﬁguring the supervisor HDD password.

If you do not want to change any other settings, you can exit BIOS Setup Utility.

►In the Exit menu, select the option Save Changes & Exit.

►SelectYes and press the Enter key.

Password

Supervisorpasswor d

Userpassword

The notebook is then rebooted and the new password comes into effect. It will now be necessary

to ﬁrst enter your supervisor or user HDD password in order to open the BIOS Setup Utility.

Please note that the user HDD password only provides access to a few of the BIOS settings.

66 Fujitsu

Security functions

Changing the supervisor HDD password or user HDD password

You can only change the supervisor HDD password when you have logged into the

BIOS Setup Utility with the supervisor HDD password.

PasswordSupervisorHDDpasswordUserHDD password

►Start the BIOS Setup Utility and go to the Security menu.

►When changing the password, proceed exactly as when assigning a password.

Removing passwords

To remove a password (without setting a new password) perform the following steps:

PasswordSupervisorpasswordUserpassword

►Start the BIOS Setup Utility and go to the Security menu.

►Highlight the Set Supervisor Password or Set User Password ﬁeld and press the Enter key.

You will be requested to enter the current password by the Enter Current Password prompt.

Enter New Password will appear and you will be requested to enter a new password.

►Press the Enter key twice at this request.

►In the Exit menu, select the option Save Changes & Exit.

►Select Yes and press the Enter key.

The notebook will now reboot with the password removed.

With the supervisor HDD password, you simultaneously deactivate the user password.

Password protection for booting the operating system

You can also prevent booting of the operating system with the supervisor

HDD password youhavesetintheBIOS Setup Utility (see section "Assigning

the supervisor and user HDD passwords", Page 66).

Operating system

Activating system protection

►Start the BIOS Setup Utility and go to the Security menu.

Operatingsystem

►Select the PasswordonBootoption and press the Enter key.

►Select the option you require (Disabled,First Boot or Every Boot) and press the enter key

►Select the Save Changes & Exit option under Exit.

The notebook will reboot. You will be prompted to enter your password

(the supervisor HDD password).

Deactivating system protection

►Start the BIOS Setup Utility and go to the Security menu.

Operatingsystem

►Select the PasswordonBootoption and press the Enter key.

►Select the Disabled option and press the Enter key.

If you do not want to change any other settings, you can exit BIOS Setup Utility.

►Select the Save Changes & Exit option under Exit.

The notebook will reboot. The system is no longer password-protected.

Fujitsu 67

Security functions

Password protection for the hard disk

Passwordprotect ion

The hard disk password prevents unauthorized access to the hard disk drives

and is checked internally each time the system is booted. The condition for this

is that you have assigned at least the supervisor HDD password.

Activating hard disk protection

►Call up the BIOS Setup and select the Security menu.

If you have not assigned BIOS passwords yet, deﬁne the supervisor and the user HDD

password now, if desired (see "Security functions", Page 63).

►Mark the Hard Disk Security ﬁeld and press the Enter key.

►In the area Drive0, mark the ﬁeld Set Master Password and press the Enter key.

Enter new Password then appears and you are asked to enter a password.

►Enter the password and press the Enter key.

Conﬁrm new Password requires you to conﬁrm the password.

►Enter the password again and press the Enter key.

With Setup Notice: Changes have been saved you receive conﬁrmation that

the new password has been saved.

►If you wish to enter a password for a second hard disk (Drive1), in the area

Drive1 mark the ﬁeld Set Master Password and proceed in exactly the same way

as for the set up of the ﬁrst hard disk (Drive0).

The ﬁeld Password Entry on Boot is set to Enabled by default. You can exit the BIOS

Setup once you have ﬁnished changing the settings.

►From the Exit menu, choose the option Exit Saving Changes.

►Press the Enter key and select Yes.

The notebook reboots and your hard disk is now protected with a password. The

password prompt is enabled as soon as the notebook has rebooted.

Deactivating hard disk protection

To cancel a password (without setting a new password) proceed as follows:

►Call up the BIOS Setup and select the Security menu.

►Mark the Hard Disk Security ﬁeld and press the Enter key.

►In the area Drive0, mark the ﬁeld Set Master Password and press the Enter key.

With the prompt Enter current Password you are ﬁrst asked to enter the old password again.

With Enter new Password you are then prompted to enter a new password.

►After the request, press the Enter key three times.

►From the Exit menu, choose the option Exit Saving Changes.

►Press the Enter key and select Yes.

The notebook reboots and there is no longer any password protection for this hard disk.

►If you wish to remove a password for a second hard disk (Drive1), in the area

Drive1 mark the ﬁeld Set Master Password and proceed in exactly the same way

as for the removal of the ﬁrst hard disk (Drive0).

68 Fujitsu

Security functions

SmartCard reader

SecurityfunctionsSecurityfunctions

SmartCards are not supplied as standard equipment. You can use all SmartCards that comply with

the ISO standard 7816-1, -2 or -3. These SmartCards are available from various manufacturers.

With the appropriate software you can use your SmartCard as an alternative to password protection,

but also as a digital signature, for encrypting your e-mails or for home banking.

We recommend that you always use two SmartCards. Always keep one of the SmartCards

in a safe place if you are carrying the other SmartCard with you.

Inserting the SmartCard

Do not use force when inserting and removing the SmartCard.

Make sure that foreign objects do not fall into the SmartCard reader.

►Slide the SmartCard into the SmartCard

reader with the chip facing upwards

(or downwards depending on the

device) and to the front.

Using the security function of the tablet buttons

If you have allotted a supervisor and/or user HDD password in the form of tablet button combinations

as described below, you can use the tablet buttons to enter this when you start your device.

Assigning the supervisor password

►Select Start - Run.

►Enter the following information in the prompt: C:\Program Files\Fujitsu\Security

Panel Application\Supervisor\FJSECS.EXE.

►Conﬁrm with Enter .

►Follow the instructions on the screen.

Fujitsu 69

Security functions

Assigning the user password

►Select Start - All Programs.

►Select Security Panel Application - Security Panel Application.

►Follow the instructions on the screen.

Entering passwords via the tablet buttons

The passwords for entry via the tablet buttons usually consist of a combination of buttons,

e.g. button 2+ button 3,fol

lowed by button 1and button ENT .

►Enter your password using buttons 1to 4.

►Conﬁrm with ENT .

The device will be unlocked.

70 Fujitsu

Security functions

Trusted Platform Module - TPM (device dependent)

TPMTrusted Platfor mM odule

To us e t h e T P M, you must enable the TPM in the BIOS Setup before the software is

installed. The requirement for this is that you have assigned at least the supervisor

HDD password (see "Security functions", Page 63).

Enabling TPM

• Requirement: You have assigned a supervisor HDD password (see "Security functions", Page 63).

►Call BIOS Setup and select the Security menu.

►Mark the TPM Security Chip Setting ﬁeld and press the Enter key.

►Select the entry Enabled to enable the TPM

Once you have enabled the TPM the Clear Security Chip menu item appears.

You can clear the holder in the TPM using Clear Security Chip.WithEnabled,

all secret keys (e.g. SRK - Storage Root Keys, AIK - Attestation Identity Keys

etc.) generated by applications are deleted.

Take note that you can then no longer access the data you have

encrypted on the holder-based keys!

►Select the Exit Saving Changes option in the Exit menu.

►Press the Enter key and select Yes .

The notebook restarts and the TPM is switched on after the reboot.

Disabling TPM

• Requirement: You have assigned a supervisor HDD password (see "Security functions", Page 63).

►Call BIOS Setup and select the Security menu.

►Mark the TPM Security Chip Setting ﬁeld and press the Enter key.

►Select the entry Disabled to disable the TPM.

►From the Exit menu, choose the option Exit Saving Changes.

►Press the Enter key and select Yes .

The notebook will now reboot with TPM deactivated.

Fujitsu 71

Connecting external devices

Under all circumstances, please observe the safety notes provided in the

"Important notes", Page 12 chapter before connecting or disconnecting

any devices to or from your notebook.

Always read the documentation supplied with the device you wish to connect.

Never connect or disconnect cables during a thunderstorm.

Never pull at a cable when disconnecting it. Always grasp the plug.

Follow the steps in the sequence below when connecting or disconnecting

devices to your notebook:

With some devices such as USB devices, it is not necessary to switch off

the notebook and the device before connecting/disconnecting. For more

information about whether or not devices need to be switched off, please refer

to the documentation supplied with the external device.

Some of the external devices require special drivers (see the operating

system and external device documentation).

Connecting devices to the notebook

1. Switch the notebook and all external devices off.

2. Unplug the AC plug of the notebook and all affected devices from the power outlets.

3. Connect the cables for all the external devices according to the instructions.

4. Plug all the AC plugs into the power outlets.

Devices,Peripherals,

Disconnecting devices from the notebook

1. Switch off the notebook and all external devices.

2. Unplug the AC plug of the notebook and all affected devices from the power outlets.

3. Disconnect the cables for all the external devices following the instructions.

Devices,Peripherals,

72 Fujitsu

Connecting external devices

HDMI port

HDMIport

The HDMI port on your notebook can be used to connect an external ampliﬁer,

LCD TV or a plasma TV with an HDMI connection.

►Connect the data cable to the

external device.

►Connect the data cable to the HDMI

port of the notebook.

Fujitsu 73

Connecting external devices

Connecting an external monitor to the port replicator

An analog monitor is connected to the analog VGA monitor port, a digital monitor to the DisplayPort

or to the DVI-D monitor port on the optional port replicator. Monitor output is limited to a maximum of

two monitors at any one time (see "Key combinations", Page 44, section "Toggle output monitor").

MonitorVGAsocketScreenc onnectionMonitorc onnection

Digital DisplayPort Analog VGA monitor port

Digital DVI-D monitor port

►Switch off the notebook and the external monitor.

►Plug the data cable of the external monitor into the monitor port.

►First switch on the external monitor and then the notebook.

You can also switch back and forth between the external screen and the LCD

screen of the notebook, see chapter "Key combinations", Page 44.

You can display the same picture on the external monitor and the

notebook LCD screen simultaneously.

74 Fujitsu

Connecting external devices

Connecting USB devices

USBports

On the USB ports you can connect external devices that also have a USB port

(e.g. a DVD drive, a printer, a scanner or a modem).

USB devices are hot-pluggable. This means you can connect and disconnect the

cables of USB devices while the operating system is running.

USB 1.x has a maximum data transfer rate of 12 Mbps.

USB 2.0 has a data transfer rate of up to 480 Mbps.

USB 3.0 has a data transfer rate of up to 5 Gbps.

Additional information can be found in the documentation for the USB devices.

►Connect the data cable to the

external device.

►Connect the data cable to a USB

port of the notebook.

Device drivers

USB devices will be automatically recognized and installed by your operating system.

Fujitsu 75

Connecting external devices

USB port with charging function (Anytime USB charge)

USBchargingfunction

It is recommended that the notebook be operated with the AC adapter connected

whenever the USB port with charging function is in use, as this function will drain

the battery more quickly if an external USB device is being charged.

The AC adapter must already be connected when the notebook is switched

off, as otherwise the USB charging function will be disabled and the

connected USB devices will not be charged.

Some USB devices (e.g. mobile telephony) require a driver in order to utilize the USB

charging function. In this case the USB charging function will not work when the

notebook is switched off, as no drivers are active when the notebook is switched off.

You can use this USB port to charge or supply power to a USB device (e.g. to charge a PDA

or a mobile phone or to connect a USB lamp), even if the notebook is switched off.

How to remove USB devices correctly

Always correctly remove the device according to the rules described below,

to ensure that none of your data is lost.

►With the left mouse button, click on the symbol in the taskbar for safe removal of hardware.

►Select the device you wish to shut down and remove.

►Press the "Enter" key.

Wait for the dialog box which tells you that it is now safe to remove the device.

76 Fujitsu

Connecting external devices

Headphones port

Connectingaudio dev icesAudioconnectionsConnectinghe adphones

You can connect headphones or external speakers to your notebook via the headphones port.

►Connect the audio cable to the

external device.

►Connect the audio cable to the headphones

port of the notebook.

The internal speakers are disabled.

If you buy a cable from a retailer, please note the following information:

The headphones port on your notebook is a "3.5 mm jack".

If you want to connect headphones or speakers you will need a "3.5 mm jack plug".

Fujitsu 77

Removing and installing components during servicing

Removing and installing components

during servicing

Only qualiﬁed technicians should repair your notebook. Unauthorized

opening or incorrect repair may greatly endanger the user (electric shock,

ﬁre risk) and will invalidate your warranty.

Components

Incaseofservice

78 Fujitsu

Settings in BIOS Setup Utility

BIOSSetupUtilitySystemsettings,BIOSSetupUtilityConﬁguration,BIOSS etupUtilitySetupConﬁguring systemConﬁguringhardware

The BIOS Setup Utility allows you to set the system functions and the hardware

conﬁguration for the notebook.

When a notebook is delivered, the factory default settings are effective. You can change

these settings in the menus of the BIOS Setup Utility. Any changes you make take

effect as soon as you save and exit the BIOS Setup Utility.

The BIOS Setup Utility program contains the following menus:

About Displays information relating to the BIOS, processor and notebook

System Advanced system settings

Advanced Conﬁguration of various hardware components, such as mouse, keyboard,

processor

Security Password settings and security functions

Boot Conﬁguration of the start-up sequence

Exit Exits the BIOS Setup Utility

Starting the BIOS Setup Utility

►Reboot the device (switch off/on or reboot the operating system).

BIOSSetupUtility

The following message (or similar) appears on the screen brieﬂy at startup:

<F2> BIOS Setup <F12> Boot Menu

►Press the function key F2 .

►If a password has been assigned, enter the password and press the Enter key.

If you have forgotten the password, contact your system administrator

or contact our customer service center.

The BIOS Setup Utility starts.

BIOS Setup Utility operation

BIOSSetupUtility

Press the F1 key to display help about operation of the BIOS Setup Utility. The description

of the individual settings is shown in the right-hand window of the BIOS Setup Utility.

With the F9 key you can load the default settings of the BIOS Setup Utility.

►Use the cursor keys ←or →to select the menu you wish to access to make changes.

The menu is displayed on the screen.

►Select the option you want to change with the cursor keys ↑or ↓.

►Press the "Enter" key.

►Press the ESC key to exit the selected menu.

►For future reference, make a note of the changes you have made (for example, in this manual).

Fujitsu 79

Settings in BIOS Setup Utility

Exiting BIOS Setup Utility

BIOSSetupUtility

You need to select the desired option in the Exit menu and activate it by pressing the Enter key:

Exit Saving Changes - save changes and exit BIOS Setup Utility

►To save the current menu settings and exit the BIOS Setup Utility, select Exit Saving Changes and Yes .

The notebook is rebooted and the new settings come into effect.

Exit Discarding Changes - Reject changes and

exit BIOS Setup Utility

►To discard the changes, select Exit Discarding Changes and Yes .

The settings in place when BIOS Setup Utility was called remain effective. BIOS

Setup Utility is terminated and the notebook is rebooted.

Load Setup Defaults – load default values

►To copy the standard entries for all menus of the BIOS Setup Utility,

choose Load Setup Defaults and Yes.

Discard Changes - Discard Changes without

exiting BIOS Setup Utility

►To discard the changes you have made, select Discard Changes and Yes.

The settings in place when BIOS Setup Utility was called remain effective.

You can now make additional settings in the BIOS Setup Utility.

►IfyouwanttoexittheBIOS Setup Utility with these settings, select Exit Saving Changes and Yes.

Save Changes - save changes without exiting

the BIOS Setup Utility

►To save the changes, select Save Changes and Yes .

The changes are saved. You can now make additional settings in the BIOS Setup Utility.

►If you want to exit BIOS Setup Utility with these settings, choose Exit Saving Changes and Yes.

Save changes and power off

►To save the changes and switch off your device, select Save Changes and Power Off and Yes.

The changes are saved. Your device is shut down.

80 Fujitsu

Troubleshooting and tips

TroubleshootingTipsFaultTroubleshooting

If a fault occurs, try to correct it as described. If you are unable to correct

the problem, proceed as follows:

►Make a note of the steps and the circumstances that led to the fault. Also

make a note of any error messages displayed.

►Switch the notebook off.

►Please contact the Hotline/Service Desk.

You can contact Fujitsu Service and Support in the following ways:

• Toll free number: 1-800-Fujitsu (1-800-838-5487)

• Website: "http://solutions.us.fujitsu.com/www/content/support/contact/index.php"

Please have the following information ready when you call:

• The model name and serial number of the notebook. The serial number is

located on a sticker on the underside of the notebook.

• Notes of any messages that appear on the screen and information on acoustic signals.

• Any changes you have made to the hardware or software since

receiving the notebook.

• Any changes you have made to the BIOS Setup settings since receiving the notebook.

• Your system conﬁguration and all peripheral devices connected to your system.

• Your sales contract.

Our notebooks have been designed primarily with mobile applications in mind.

This means that considerable effort has been made to optimize components and

equipment in terms of weight, space and energy requirements. Depending on the

particular conﬁguration you have purchased, it is possible that functionality may be

slightly reduced compared to a desktop PC if you are running processor-intensive

gaming software, e.g. games with intensive 3D graphics. Updating your hardware with

drivers which have not been approved by Fujitsu may result in performance losses,

data losses or malfunction of the equipment. A list of approved drivers and current

BIOS versions can be downloaded from: "http://solutions.us.fujitsu.com"

Help if problems occur

Should you encounter a problem with your computer that you cannot resolve yourself:

►Note the ID number of your device. The ID number is found on the type rating

plate on the back or underside of the casing.

►For further clariﬁcation of the problem, contact the Fujitsu Service Desk. When you do

this, please have ready the ID number and serial number of your system.

Recovering your Factory Image

Harddisk:Operatingsystem,recoveringFactoryImage

In the event you need to restore your original Factory Image refer to the

steps in the Appendix of this manual.

Fujitsu 81

Troubleshooting and tips

The notebook’s date or time is incorrect

SummertimeWintertim eIncorre cttimeTimeno tcorrectWrongdate/timeDatenotcorrectChargingback-up bat tery

Cause Troubleshooting

Time and date are wrongly set. ►With the BIOS-Setup-Utility,you can set the

date and time in the Main menu.

Date and time are still set incorrectly after

switching on the notebook.

►Please contact your sales outlet or our

hotline/service desk.

Battery indicator does not illuminate

Cause Troubleshooting

The battery is not installed correctly. ►Switch the notebook off.

►Check whether the battery is installed

correctly in its compartment.

►Switch the notebook on.

The battery is discharged. ►Charge the battery.

►Install a charged battery.

►Connect the notebook to a AC outlet

using the AC adapter.

When certain characters are entered on the

keyboard, only numerals are written

Abeepsounds e verys eco nd

Cause Troubleshooting

The virtual number keys of your device are

activated, see "Virtual number keys", Page 43

►Press the Num button.

The notebook’s LCD screen remains blank

LCDscreenBlankLC Dscreen

Cause Troubleshooting

Screen is switched off. ►Press a key or touch the Clickpad.

External monitor or television set connected. ►Press the key combination for changing over

the screen output, see "Key combinations",

Page 44.

82 Fujitsu

Troubleshooting and tips

The LCD screen of the notebook is difﬁcult to read

LCDscreenLCDscreen

Cause Troubleshooting

Reﬂected glare ►Turn the notebook or alter the tilt of the LCD

screen.

►Increase the brightness of the screen.

The external monitor remains blank

Monitor

Cause Troubleshooting

Monitor is switched off. ►Switch the external monitor on.

Power saving has been activated (monitor is

blank).

►Press any key to continue.

Brightness is set to dark. ►Adjust the brightness of the monitor.

Screen output is set to the notebook’s LCD

screen

►Press the key combination for changing over

the screen output, see "Key combinations",

Page 44.

The external monitor’s AC cable or data cable is

not connected properly.

►Switch off the external monitor and the

notebook.

►Check whether the AC cable is plugged

properly into the external monitor and into

the power outlet.

►Check whether the data cable is properly

connected to the notebook and the external

monitor (if it is plugged in with a connector).

►Switch on the external monitor and the

notebook.

The external monitor is blank or the image is unstable

MonitorMonitor

Cause Troubleshooting

The wrong external monitor has been selected

or the wrong screen resolution has been set for

the application program.

►Terminate the application program under

Windows by pressing Alt +F4 .Ifthe

error persists after terminating the program,

use the key combination for switching the

screen output (see "Key combinations",

Page 44), in order to switch to the LCD

screen of the notebook.

Change the following setting:

►Set the screen resolution: Set the screen

resolution as described in the documentation

for your operating system.

►Select monitor: Select monitor 1 or 2 as

described in the documentation for your

operating system.

Fujitsu 83

Troubleshooting and tips

The cursor does not correctly follow the

stylus movements

Cause Troubleshooting

Stylus incorrectly calibrated. ►Calibrate the stylus as shown under

Hardware and Sound / Tablet PC Settings

in the Control Panel, see "Adjusting the

stylus", Page 37 and "Calibrating the stylus",

Page 37.

Stylus input not working

Cause Troubleshooting

Incorrect driver installed. ►If your device is one which can only be

operated using the stylus, install the driver

for the standard model.

►If your device is one which can be

operated using the stylus and by ﬁnger,

install the driver for the "Dual Digitizer"

model.

The notebook does not start after switching it on

Notebook

Cause Troubleshooting

The battery is not installed correctly. ►Check whether the battery is installed

correctly in its compartment.

►Switch the notebook on.

The battery is discharged. ►Charge the battery.

►Insert a charged battery.

►Connect the AC adapter to the notebook.

The AC adapter is not properly connected. ►Check whether the AC adapter is properly

connected to the notebook.

►Switch the notebook on.

84 Fujitsu

Troubleshooting and tips

The notebook stops working

NotebookEnding

Cause Troubleshooting

The notebook is in energy saving mode. ►End energy saving mode.

An application program has caused the

malfunction.

►Close the application program or restart

the notebook (by restarting the operating

system or switching the device off and back

on again).

The battery is discharged. ►Charge the battery.

►Insert a charged battery.

►Connect the AC adapter to the notebook.

The printer does not print

Printerdoesnot print

Cause Troubleshooting

The printer is not switched on. ►Make sure that the printer is switched

on and ready for operation (refer to the

documentation supplied with the printer).

The printer is not connected correctly. ►Check that the data cable connecting

the notebook to the printer is properly

connected.

The printer driver is faulty or not correctly

installed, or it is the wrong printer driver.

►Check that the data cable connecting

the notebook to the printer is properly

connected.

►Check whether the correct printer driver is

loaded (refer to the printer documentation).

The wireless connection to a network does not work

Thewirelessconnection toanetw orkdoesnot work

Cause Troubleshooting

The wireless component is switched off. ►Switch the wireless component on (see

"Switching the wireless components on and

off", Page 55).

The wireless component is switched on. Despite

this, the wireless connection to a network does

not work.

►Check whether the wireless connection is

enabled by the software.

►Further information on using the wireless

component can be found in the help ﬁles.

Fujitsu 85

Troubleshooting and tips

The battery discharges too quickly

Battery

Cause Troubleshooting

The battery is either too hot or too cold. In this

case the battery indicator ﬂashes.

►Move the notebook so that its temperature

returns to within the normal range.

►If the operating time of the battery life is

extremely short, the battery is probably too

old. Replace the battery if necessary.

You may have an application running that

consumes a great deal of power due to frequent

accessing of the hard disk or optical drive.

►Use the AC adapter whenever possible.

The maximum brightness may have been set

for the screen.

►Set the screen slightly darker with the

key combination for Decreasing the screen

brightness in order to reduce the amount of

power being drawn.

SmartCard reader is not recognized

Cause Troubleshooting

Chip card inserted incorrectly. ►Make sure you have inserted your

SmartCard into the SmartCard reader with

the chip facing upwards.

►Check whether the SmartCard you are using

is supported. Your SmartCard must comply

with the ISO standard 7816-1, -2, -3 and -4.

SmartCard PIN forgotten

Cause Troubleshooting

PIN forgotten ►If you are working in a network, contact your

system administrator, who can unlock your

notebook with a Supervisor PIN.

SmartCard lost

Cause Troubleshooting

SmartCard lost. ►If you are working in a network, contact your

system administrator, who can boot your

notebook with a Supervisor SmartCard.

86 Fujitsu

Troubleshooting and tips

User and/or supervisor SmartCard lost

Cause Troubleshooting

User and/or supervisor SmartCard lost ►If you have lost your user SmartCard, you

can continue working with the supervisor

SmartCard.

►If you have lost the supervisor SmartCard,

you can also continue working, but you no

longer have all rights and cannot initialize

another supervisor SmartCard.

Acoustic warning

Acous tic wa rnin gsErrors

Cause Troubleshooting

A beep sounds every few seconds.

The battery is almost ﬂat.

►Charge the battery.

Fujitsu 87

Troubleshooting and tips

Error messages on the screen

Errormessages onthes creenErrors

This section describes the error messages generated by the BIOS Setup. Error messages displayed

by the operating system or programs are described in the documentation for these programs.

If the error message appears repeatedly despite troubleshooting measures,

contact the place of purchase or our customer service center.

Error message/cause Troubleshooting

CMOS Battery Bad

If the error message occurs repeatedly, the

back-up battery in the notebook is ﬂat.

►Contact your sales outlet or our customer

service center.

System CMOS checksum bad - Default conﬁguration

used

The system conﬁguration information is

incorrect.

►Switch the notebook off.

►Switch the notebook on.

►Press the function key F2 to access the

BIOS Setup.

►In the BIOS Setup, select the Exit menu.

►Select the entry Load Setup Defaults.

►Select OK and press the Enter key.

Extended memory failed at offset: xxxx Failing Bits:

zzzz zzzz

When testing the extended memory. an error

has resulted at the address xxxx.

►Check whether the additional memory

module has been inserted correctly.

Failure Fixed Disk n

The settings of the hard disk drive are incorrect.

►Start the BIOS Setup (Primary Master

submenu) and select the correct settings.

Keyboard controller error ►Switch the notebook off with the ON/OFF

button.

►Wait 3 - 5 seconds and switch on the

notebook again.

Keyboard error If you use an external keyboard:

►Check the connection and reboot the

notebook.

nn Stuck key ►Make sure that no key is pressed.

Operating system not found ►Check in the BIOS Setup whether your hard

disk has been set correctly.

►Make sure that the operating system is

installed on the corresponding drive.

Press <F1> to resume, <F2> to SETUP

This error message appears if an error occurs

during the self-test before starting the operating

system.

►Press the F1 function key to start the

operating system.

►Press the function key F2 to access the

BIOS Setup.

88 Fujitsu

Troubleshooting and tips

Error message/cause Troubleshooting

Previous boot incomplete - Default conﬁguration

used Default values have been set for certain

settings because of an error which occurred in

the previous system boot. Check the settings in

the BIOS Setup.

►Press the F1 function key when prompted

to do so.

Real time clock error ►Contact your sales outlet or our customer

service center.

nnnnK Shadow RAM failed at offset: xxxx Failing

Bits: zzzz

►Contact your sales outlet or our customer

service center.

System battery is dead - Replace and run SETUP ►Contact your sales outlet or our customer

service center.

System cache error - Cache disabled ►Contact your sales outlet or our customer

service center.

System timer error ►Contact your sales outlet or our customer

service center.

Fujitsu 89

Technical data

Notebook

General

Processor 4th Generation Intel®Core™with vPro™

technology (depending on the CPU)

4400 memory (SO DIMM) Maximum 8 GB DDR3

1ﬁxed slot for 4 GB or 8 GB modules

Electrical data

Safety regulations complied with CE, GS (optional)

Protection class II

Maximum power draw (when the notebook is

switched on and the battery is charged):

65 W (without port replicator) /

80 W (with port replicator)

LCD screen

Size 33.78 cm / 13.3" TFT WQHD

Resolution 2560 x 1440 pixels / 32-bit

Pixel class II

Brightness control 12 levels

Technology Wide-View High-Bright WXGA Display with LED

Background Lighting

Digitizer and glass panel • Dual Digitizer

• Hardened glass

Webcam FHD, 30 fps, (optional) with status indicator

Display adapter

Chip Intel® HD Graphics 4400

Maximum resolution of external monitor: 4096 x 2304 pixels

Dimensions

Width x Depth x Height 320.8 mm x 235 mm x 17.1-19.3 mm /

12.63 inch x 9.25 inch x 0.67-0.76 inch

Weight depending on conﬁguration from 1.5 kg / 3.3 lbs

Input devices

Keyboard 85 keys, with backlit keyboard

Clickpad 2keys

Tablet buttons 1 Windows button, 2 volume buttons

Stylus 1 freely programmable rocker button

Slots

Storage card slot 1 x SD Card

SmartCard slot 1x

SIM card slot 1x

90 Fujitsu

Technical data

Ports

HDMI port 1 x

LAN port Socket, RJ45

Microphone port / Line In / Headphones port /

Line Out

3.5mmstereominijack

Docking port Socket, 54-pin

USB (Universal Serial Bus) Total: 2x USB (1 x USB 3.0, 1 x USB 3.0 with

charging function (Anytime USB charge)

Security Lock 1x

Ambient conditions

Environment class DIN IEC 721 7K1

Mechanism class DIN IEC 721 7M2

Operating temperature 5℃.... 35℃/ 41°F ....95°F

Transit temperature (2K2) –15°C .... 60°C / 5°F .... 140°F

Fujitsu 91

Technical data

WLAN speciﬁcations

Type of network Integrated Dual-Band Wireless-N 7260 device

conforms to IEEE 802.11a, 802.11b/g, and

802.11n, Wi-Fi based*.

Transfer rate (Automatic switching) IEEE802.11 a and

g: 54 Mbps max. data rate; IEEE802.11n:

300 Mbps max. data rate

Active frequency • 802.11n: 2.4 GHz or 5 GHz

• 802.11b/g: 2400~2473 MHz

• 802.11a: 4900 ~ 5850 MHz

Typical operating distances** • 802.11a: 40 ft. (12 m) @ 54 Mbps; 300 ft.

(91m)@6Mbps

• 802.11b: 100 ft. (30 m) @ 11 Mbps; 300 ft.

(91m)@1Mbps

• 802.11g: 100 ft. (30 m) @ 54 Mbps; 300 ft.

(91m)@1Mbps

• 802.11n: Estimated double the operating

distance of 802.11g and 802.11a in their

respective frequencies.

Number of channels • 802.11a: 8 independent channels

• 802.11b/g: 11 channels, 3 non-overlapping

channels

• 802.11n: Channel bonding takes two of

the non-overlapping 20MHz channels and

combines it into one 40MHz channel. It is

actually 12 non-overlapping channels with

channel bonding and 24 without. Also, it is

1 non-overlapping channel in 2.4GHz when

channel bonding is used

Security Encryption Types - WEP, TKIP, AES***, WPA 1.0

and WPA 2.0 compliant

Encryption Key lengths Supported: 64 bits and

128 bits

Maximum recommended number of computers

to be connected over wireless LAN (during ad

hoc connection)

10 units or less ****

* “Wi-Fi based” indicates that the interconnectivity test of the organization which guarantees the

interconnectivity of wireless LAN (Wi-Fi Alliance) has been passed.

** The communication ranges shown above will increase or decrease depending on factors such

as number of walls, reﬂective material, or interference from external RF sources.

*** Encryption with network key (WEP) is performed using the above number of bits, however,

users can set 40 bits/ 104 bits after subtracting the ﬁxed length of 24 bits.

**** Depending on practical environments, the allowable number of computers to be connected

may be decreased.

92 Fujitsu

Technical data

Port replicator (optional)

Electrical data

Safety regulations complied with CE

Protection class II

Ports

Monitor port (analog) 15-pin

Monitor port (digital) 25-pin, DVI-D

DisplayPort 1 x

LAN port RJ45

USB (Universal Serial Bus) 4x USB 3.0

Audio Headphones port

Docking port 100-pin

Security Lock 1x

Ambient conditions

Environment class DIN IEC 721 7K1

Mechanism class DIN IEC 721 7M2

Operating temperature 5℃.... 35℃/ 41°F .... 95°F

Transit temperature –15°C .... 60°C / 5°F .... 140°F

Rechargeable battery

For information on the batteries used in your device, please see

"http://solutions.us.fujitsu.com/www/content/support/contact/index.php".

Rated voltage 14.4 V

Rated capacity 45 Wh

Rated power 3150 mAh

The operating time depends on the device conﬁguration, the active

applications and the energy saving settings.

Fujitsu 93

Technical data

AC adapter for use with notebook and port replicator

The following technical data applies to the AC adapter included in the scope of

delivery of the notebook and the optionally available port replicator.

Primary

Rated voltage 100 V to 240 V (automatic)

Rated frequency 50 Hz to 60 Hz (automatic)

Max. rated current 0.7 A to 1.2 A

Secondary

Rated power 100 W

Rated voltage 19 V

Max. rated current 5.27 A

An additional AC adapter or AC cable can be ordered at any time.

94 Fujitsu

Manufacturer’s notes

Disposal and recycling

Notes

You can ﬁnd information on this subject on your notebook or on our website

("http://solutions.us.fujitsu.com/www/content/products/trade-in_program/").

Recycling your battery

Over time, the batteries that run your mobile computer will begin to hold a charge for a

shorter amount of time; this is a natural occurrence for all batteries. When this occurs,

you may want to replace the battery with a fresh one*. If you replace it, it is important

that you dispose of the old battery properly because batteries contain materials that

could cause environmental damage if disposed of improperly.

Fujitsu is very concerned with environmental protection, and has enlisted the services of the

Rechargeable Battery Recycling Corporation (RBRC)**, a nonproﬁt public service organization

dedicated to protecting our environment by recycling old batteries at no cost to you.

RBRC has drop-off points at tens of thousands of locations throughout the United States and

Canada. To ﬁnd the location nearest you, go to "www.RBRC.org" or call 1-800-822-8837.

If there are no convenient RBRC locations near you, you can also go to the EIA Consumer

Education Initiative website "http://EIAE.org/ " and search for a convenient disposal location.

Remember – protecting the environment is a cooperative effort, and we must

make every effort to protect it for current and future generations.

* To order a new battery for your Fujitsu mobile computer, go to the Fujitsu shopping site

at "www.shopfujitsu.com" in the US or "www.fujitsu.ca/products/notebooks" in Canada.

** RBRC is an independent third party to which Fujitsu provides funding for

battery recycling; RBRC is in no way afﬁliated with Fujitsu.

DOC (Industry CANADA) Notices

DOC(INDUSTRYCANADA)NOTICES

Radios and Television

This Class B digital apparatus meets all requirements of Canadian Interference-Causing Equipment

Regulations.

CET appareil numérique de la class B respecte toutes les exigence du Réglement

sur le matérial brouilleur du Canada.

Fujitsu 95

Manufacturer’s notes

UL Notice

IMPORTANT SAFETY INSTRUCTIONS

This unit requires an AC adapter to operate. Only use UL Listed I.T.E. adapters with an output rating

of 19 VDC, with a minimum current of 3.16A (60W). The correct output rating is indicated on the

AC adapter label. Refer to the illustration below for the correct AC Adapter output polarity:

When using your notebook equipment, basic safety precautions should always be followed to

reduce the risk of ﬁre, electric shock and injury to persons, including the following:

• Do not use this product near water for example, near a bathtub, washbowl, kitchen

sink or laundry tub, in a wet basement or near a swimming pool.

• Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a

ﬁre. They may explode. Check with local codes for possible special disposal instructions.

SAVE THESE INSTRUCTIONS

For Authorized Repair Technicians Only

CAUTION:

For continued protection against risk of ﬁre, replace only with the

same type and rating fuse.

WARNING:

Danger of explosion if Lithium (CMOS) battery is incorrectly replaced. Replace only

with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer’s instruction.

96 Fujitsu

Manufacturer’s notes

ENERGY STAR Compliance

Your Fujitsu system is an ENERGY STAR qualiﬁed mobile PC. By choosing a computer with the

latest energy-saving technology, you’re helping to preserve our environment for future generations.

ENERGY STAR is a joint program of the U.S. Environmental Protection Agency, U.S. Department

of Energy, Natural Resources Canada, and other governments around the world helping us save

money while protecting the environment through energy efﬁcient products and practices. With

energy costs and global warming top-of-mind for consumers, Fujitsu is committed to offering

solutions that help consumers conserve energy and improve the quality of our environment.

Sleep Mode:

You will notice that your computer is initially set so that the display turns off after 15 minutes of

user inactivity, and the computer goes into Sleep mode after 20 minutes of user inactivity. When

going into Sleep mode, the computer also reduces the speed of any active Ethernet network

links. To “wake” the computer from Sleep mode, press the Suspend/Resume Button.

Energy saving beneﬁts:

Fujitsu ENERGY STAR qualiﬁed mobile PCs use about half as much electricity as standard

equipment – saving half in utility costs. But more than that, ENERGY STAR also makes a difference

for the environment. Did you know that the average house can be responsible for twice the

greenhouse gas emissions as the average car? That’s because every time you ﬂip on a light

switch, run your dishwasher, or turn on your PC, you use energy, which means more greenhouse

gas emissions from power plants. So the more energy we can save through energy efﬁciency,

the more we help to reduce greenhouse gases and the risks of global warming.

To learn more about the important ENERGY STAR program, visit:"www.energystar.gov".

To read about how Fujitsu is supporting Sustainable Management along with

several other environmental activities, visit the Fujitsu Corporate Citizenship page at:

"http://www.computers.us.fujitsu.com/www/content/aboutus/environmental/environment.php".

Declarations of Conformity

Declarationof conformity

This device complies with Part 15 of the FCC rules. Operations are subject to the following two

conditions: (1) This device may not cause harmful interference, (2) This device must accept any

interference received, including interference that may cause undesired operation.

Fujitsu 97

Manufacturer’s notes

FCC and IC Regulatory Information

Please note the following regulatory information related to the wireless LAN

device.

Regulatory Notes and Statements

Wireless LAN, Health and Authorization for use

Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of

these emissions, however, are far much less than the electromagnetic energy emissions from wireless

devices such as mobile phones. Wireless LAN devices are safe for use by consumers because they

operate within the guidelines found in radio frequency safety standards and recommendations. The

use of Wireless LAN devices may be restricted in some situations or environments, such as:

• On board an airplane, or

• In an explosive environment, or

• In situations where the interference risk to other devices or services is

perceived or identiﬁed as harmful.

In cases in which the policy regarding use of Wireless LAN devices in speciﬁc environments is

not clear (e.g., airports, hospitals, chemical/oil/gas industrial plants, private buildings), obtain

authorization to use these devices prior to operating the equipment.

Regulatory Information/Disclaimers

Installation and use of this Wireless LAN device must be in strict accordance with the instructions

included in the user documentation provided with the product. Any changes or modiﬁcations made

to this device that are not expressly approved by the manufacturer may void the user’s authority to

operate the equipment. The manufacturer is not responsible for any radio or television interference

caused by unauthorized modiﬁcation of this device, or the substitution or attachment of connecting

cables and equipment other than those speciﬁed by the manufacturer. It is the responsibility of the

user to correct any interference caused by such unauthorized modiﬁcation, substitution or attachment.

The manufacturer and its authorized resellers or distributors will assume no liability for any damage

or violation of government regulations arising from failure to comply with these guidelines.

This device must not be co-located or operated in conjunction with any other antenna or transmitter.

For IEEE 802.11a Wireless LAN: For operation within 5.15~5.25 GHz frequency range, it is

restricted to indoor environments, and the antenna of this device must be integral.

Federal Communications Commission and Industry Canada statement:

This device complies with Part 15 of FCC Rules and Industry Canada license exempt RSS standard(s).

Operation is subject to the following two conditions: (1) This device may not cause

interference, and, (2) This device must accept any interference, including interference

that may cause undesired operation of this device.

98 Fujitsu

Manufacturer’s notes

Déclaration d’Industrie Canada

Cet appareil est conforme à la Section 15 des Règles de la FC C et à la ( aux) norme(s)

RSS concernant les appareils exempt s de licence par Industrie Canada. Son fonctionnement

est soumis aux deux condition s suivantes : (1) cet appareil ne doit pas causer d’interférence

nuisib le; (2) cet appareil doit accepter toutes les interférences reçues, y compris celles

pouvan t causer un mauvais fonctionnement de l’appareil.

FCC Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses, and can radiate radio frequency energy. If not installed and used in accordance with

the instructions, it may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try and

correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the distance between the equipment and the receiver.

3. Connect the equipment to an outlet on a circuit different from the one the receiver is connected to.

4. Consult the dealer or an experienced radio/TV technician for help.

FCC Radio Frequency Exposure statement

The available scientiﬁc evidence does not show that any health problems are associated with

using low power wireless devices. There is no proof, however, that these low power wireless

devices are absolutely safe. Low power wireless devices emit low levels of radio frequency

energy (RF) in the microwave range while being used. Whereas high levels of RF can produce

health effects (by heating tissue), exposure to low-level RF that does not produce heating

effects causes no known adverse health effects. Many studies of low-level RF exposure have

not found any biological effects. Some studies have suggested that some biological effects

might occur, but such ﬁndings have not been conﬁrmed by additional research.

The wireless LAN radio device has been tested and found to comply with FCC radiation

exposure limits set forth for an uncontrolled equipment and meets the FCC radio frequency

(RF) Exposure Guidelines in Supplement C to OET65.

The exposure standard for wireless devices employs a unit of measurement known as the Speciﬁc

Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg, and 1.6W/kg by Industry Canada.

This device is compliant with SAR for general population /uncontrolled exposure limits in

ANSI/IEEE C95.1-1992 and Canada RSS 102, and had been tested in accordance with

the measurement methods and procedures speciﬁed in OET Bulletin 65 Supplement C,

and Canada RSS 102. This device has been tested, and meets the FCC, IC RF exposure

guidelines when tested with the device operating conditions.

Fujitsu 99

Manufacturer’s notes

Déclaration de la FCC/d’Industrie Canada sur l’exposition

aux radiofréquences

La norme régissant l’exposition des appareils sans ﬁl aux radiofréquences emploie une unité

de mesure dénommée Taux d’absorption spéciﬁque, ou TAS. La FCC et Industrie Canada ont

déﬁni la même limite de TAS : 1,6 W/kg. Cet appareil est conforme au TAS pour les limites

d’exposition générales de la population/non contrôlées déﬁnies par les règles C95.1-1992 de

l’ANSI/IEEE et RSS 102 d’Industrie Canada ; il a été testé en conformité avec les méthodes

et procédures de mesure spéciﬁées dans le supplément C du bulletin 65 de l’OET (Ofﬁce

d’ingénierie et de technologie) et la règle RSS 102 d’Industrie Canada. Cet appareil a été testé

selon les directives de la FCC et d’IC concernant l’exposition aux radiofréquences et s’est révélé

conforme à ces dernières lorsqu’il a été testé en contact direct avec le corps.

Export restrictions

This product or software contains encryption code which may not be exported or transferred

from the US or Canada without an approved US Department of Commerce export license.

This device complies with Part 15 of FCC Rules., as well as ICES 003 B / NMB 003 B.

Operation is subject to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received, including interference

that may cause undesirable operation. Modiﬁcations not expressly authorized by Fujitsu

America, Inc. may invalidate the user’s right to operate this equipment.

Canadian Notice

The device for the 5150 - 5250 MHz band is only for indoor usage to reduce the potential

for harmful interference to co-channel mobile satellite systems.

The maximum antenna gain of 6 dBi permitted (for devices in the 5250 - 5350 MHz, 5470 - 5725 MHz

and 5725 - 5825 MHz bands) to comply with the e.i.r.p. limit as stated in A9.2 of RSS210.

In addition, users are cautioned to take note that high power radars are allocated as primary

users (meaning they have priority) of 5250 - 5350 MHz and 5650 - 5850 MHz and these

radars could cause interference and/or damage to LE-LAN devices.

Avis pour le Canada

Le matériel destiné à un usage sur la bande 5 150 - 5 250 MHz doit être utilisé

uniquement à l’intérieur aﬁn de réduire les risques de brouillage nuisible causé aux

systèmes mobiles par satellite fonctionnant sur un même canal.

Un gain d’antenne de 6 dBi est autorisé (pour le matériel utilisant les bandes 5 250 - 5 350 MHz,

5 470 - 5 725 MHz et 5 725 - 5 825 MHz), conformément à la limite p.i.r.e. maximale

permise selon l’annexe A9.2 afférent aux périphériques RSS210.

En outre, les utilisateurs doivent prendre garde au fait que les radars de grande puissance

sont considérés comme des utilisateurs principaux (ce qui signiﬁe qu’ils sont prioritaires) des

bandes 5 250 - 5 350 MHz et 5 650 - 5 850 MHz et qu’ils pourraient causer des interférences

et/ou des dommages aux appareils de réseau exempts de licence.

100 Fujitsu

Appendix

Before Using the Optional Wireless LAN

This manual describes the procedures required to properly set up and conﬁgure the optional

integrated Wireless LAN Mini-PCI device (referred to as "WLAN device" in the rest of the

manual). Before using the WLAN device, read this manual carefully to ensure its correct

operation. Keep this manual in a safe place for future reference.

Wireless LAN Devices Covered by this Document

This document is applicable to systems containing the following device:

• Intel® Dual Band Wireless-N 7260

Characteristics of the WLAN Device

• The WLAN devices are PCI Express Mini cards attached to the main board of the mobile computer.

• The WLAN devices operate in license-free RF bands, eliminating the need to procure

an FCC operating license. The WLAN operates in the 2.4GHz Industrial, Scientiﬁc,

and Medical (ISM) RF band and the lower, middle, and upper bands of the 5GHz

Unlicensed National Information Infrastructure (UNII) bands.

• The WLAN devices are capable of four operating modes, IEEE802.11a,

IEEE802.11b, IEEE802.11g, and IEEE802.11n.

• The WLAN device is Wi-Fi certiﬁed and operates (as applicable) at the maximum data

rate of 450 Mbps in IEEE802.11n mode (300 Mbps in this conﬁguration); 54 Mbps

in IEEE802.11g mode; and 11 Mbps in IEEE802.11b mode.

• The WLAN devices support the following encryption methods - WEP,

TKIP, CKIP, and AES encryption.

• The Wireless LAN devices are compliant with the following standards: WPA,

WPA2, CCX1.0, CCX2.0, CCX3.0, and CCX4.0.

Fujitsu 101

Appendix

Wireless LAN Modes Using this Device

Ad Hoc Mode

"Ad Hoc Mode" refers to a wireless network architecture where wireless network connectivity

between multiple computers is established without a central wireless network device, typically

known as Access Point(s). Connectivity is accomplished using only client devices in a peer-to-peer

fashion. That is why Ad Hoc networks are also known as peer-to-peer networks. Ad Hoc

networks are an easy and inexpensive method for establishing network connectivity between

multiple computers. Ad Hoc mode requires that the SSID, network authentication, and encryption

key settings are identically conﬁgured on all computers in the Ad Hoc network.

Access Point (Infrastructure) Mode

Infrastructure mode refers to a wireless network architecture in which devices communicate with

wireless or wired network devices by communicating through an Access Point. In infrastructure

mode, wireless devices can communicate with each other or with a wired network. Corporate

wireless networks operate in infrastructure mode because they require access to the WLAN in

order to access services, devices, and computers (e.g., ﬁle servers, printers, databases).

102 Fujitsu

Appendix

* = An optional hub for a wired LAN may

be required depending upon the type

of access point used.

** = ADSL modem, cable modem, or similar

How to Handle This Device

The WLAN device is an optional device that may come pre-installed in your mobile computer. Under

normal circumstances, it should not be necessary for you to remove or re-install it. The Operating

System that your mobile computer comes with has been pre-conﬁgured to support the WLAN device.

• Integrated Intel Centrino wireless LAN devices support IEEE802.11a,

IEEE802.11b, IEEE802.11g, and IEEE802.11n.

• The WLAN device operates in the 2.4 GHz ISM band and the 5 GHz

lower, middle, and upper UNII bands.

• Microwave ovens may interfere with the operation of WLAN devices since they operate in the

same 2.4 GHz frequency range as IEEE802.11b/g/n devices. Interference by microwaves

does not occur with IEEE802.11a radio which operates in the 5 GHz RF band.

• Wireless devices that transmit in the 2.4 GHz range may interfere with operation of WLAN

devices in IEEE802.11b/g/n modes. Symptoms of interference include reduced throughput,

intermittent disconnects, and many frame errors. It is HIGHLY recommended that these

interfering devices be powered off to ensure proper operation of the WLAN device.

Fujitsu 103

Appendix

Deactivating/Disconnecting the WLAN Device

Disconnecting the WLAN device may be desired in certain circumstances (to extend battery

life) or where certain environments require it (i.e. hospitals, clinics, airplanes, etc.). The

WLAN device can be disconnected in Windows using the WLAN icon in the system tray

(Note that disconnecting via the icon in the system tray does not turn off the radio; it

continues to transmit and receive even though it’s not connected.)

►Press the key combination Fn +F5 to deactivate the Wireless Device

WirelessLANWirelessLANBluetoothBluetooth

The wireless component indicator will go off when the wireless components are switched off.

Conﬁguring the Wireless LAN

The optional WLAN device can be conﬁgured to establish wireless network connectivity

using the software that is built into Windows. Support for most industry standard

security solutions is contained in this software.

Pre-deﬁned parameters will be required for this procedure. Please consult with

your network administrator for these parameters:

Conﬁguring the WLAN Using Windows

The WLAN device canbeconﬁgured to establish wireless network connectivity using

the software that is built into Windows Vista. Support for most industry standard

security solutions is contained in this software.

Pre-deﬁned parameters are required for this procedure. Consult your network

administrator for these parameters:

1. From the ModernStartscreen, press Windows +X, then select Control Panel from the menu.

2. If the Control Panel is not in Classic View, select Classic View from the left panel.

Double-click the Network and Sharing Center icon.

3. Select Setup a new connection or network.

4. Depending upon what type of connection you would like to make, make a selection. For

an infrastructure network, select Manually connect to a wireless network.

5. Enter the required information. It may be necessary to consult with your network

administrator for some of the information.

6. In the event you require assistance, go to the Network and Sharing Center window (Control

Panel > Network and Sharing Center), and type in relevant keywords in the Search box.

Connection to the network

After you have conﬁgured your computer, you can connect to an active network

by performing the following steps:

1. Click on the WLAN icon in the system tray.

2. Select Connect to a network.

3. Select a network from the list that appears, and click the Connect button.

104 Fujitsu

Appendix

Troubleshooting the WLAN

Causes and countermeasures for troubles you may encounter while using your

wireless LAN are described in the following table.

Problem Possible Cause Possible Solution

Incorrect network name (SSID)

or network key

Ad hoc connection: verify that

the network names (SSID’s)

and network keys (WEP) of

all computers to be connected

have been conﬁgured correctly.

SSID’s and WEP key values

must be identical on each

machine.

Access Point (Infrastructure)

connection: set the network

name (SSID) and network key

to the same values as those of

the access point.

Set the Network Authentication

value identically to that of the

Access Point. Please consult

your network administrator for

this value, if necessary.

Unavailable network connection

Weak received signal strength

and/or link quality

Ad hoc connection: Retry

connection after shortening

the distance to the destination

computer or removing any

obstacles for better sight.

Access Point (Infrastructure)

connection: Retry connection

after shortening the distance to

the access point or removing

any obstacles for better sight.

Fujitsu 105

Appendix

Problem Possible Cause Possible Solution

The WLAN device was

deactivated or is disabled

Check if the wireless switch

is turned On. Go to Start >

Control Panel, and doubleclick

on Windows Mobility Center.If

the wireless network is off, click

the Turn wireless on button.

The computer to be connected

is turned off

Check if the computer to be

connected is turned ON.

Incorrectly conﬁgured network

settings

Recheck the conﬁguration of

your network settings.

RF interference from Access

Points or other wireless

networks

The use of identical or

overlapping RF channelscan

cause interference with the

operation of the WLAN device.

Change the channel of your

Access Point to a channel

that does not overlap with the

interfering device.

Wireless network authentication

has failed

Re-check your Network

Authentication, Encryption,

and Security settings.

Incorrectly conﬁgured

security settings such as

an incorrectly typed WEP

key, a mis-conﬁgured LEAP

username, or anincorrectly

chosen authentication method

will cause theLANdeviceto

associate but not authenticate

to the wireless network.

Unavailable network connection

(continued)

Incorrect IP address

conﬁguration

This only applies to networks

using static IP addresses.

Please contact your network

administrator for the correct

settings.

106 Fujitsu

Appendix

Using the Bluetooth Device

Bluetooth is integrated into the Wireless LAN module. The Bluetooth capabilities are Bluetooth

Basic, EDR and Bluetooth Low Energy (BT v4.0) operational modes.

What is Bluetooth

Bluetooth technology is designed as a short-range wireless link between mobile devices, such

as laptop computers, phones, printers, and cameras. Bluetooth technology is used to create

Personal Area Networks (PANs) between devices in short-range of each other.

To enable or disable either the wireless LAN or Bluetooth devices

individually, perform the following steps:

1. Turn on the WLAN/Bluetooth using the Fn and F5 keys.

2. Go to the Modern Start screen and select Charms > Settings >

Change PC Settings > Wireless.

3. Under Wireless > Wireless Devices, click on the Bluetooth switch to turn it on.

Where to Find Information About Bluetooth

For additional information about Bluetooth Technology, visit the Bluetooth

Web site at: "www.bluetooth.com".

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. The Bluetooth antenna is located on the top edge of the LCD screen and

is exempt from minimum distance criteria due to its low power.

The transmitters in this device must not be co-located or operated in conjunction

with any other antenna or transmitter.

Canadian Notice

To prevent radio interference to the licensed service, this device is intended to be

operated indoors and away from windows to provide maximum shielding. Equipment (or

its transmit antenna) that is installed outdoors is subject to licensing.

Warranty

Users are not authorized to modify this product. Any modiﬁcations invalidate the warranty.

This equipment may not be modiﬁed, altered, or changed in any way without signed

written permission from Fujitsu. Unauthorized modiﬁcation will void the equipment

authorization from the FCC and Industry Canada and the warranty.

Fujitsu 107

Appendix

Image Backup and Recovery Procedures

Thank you for purchasing a Fujitsu computer. Fujitsu is committed to bringing you

the best computing experience with your new system.

It is very important that you create DVD copies of your Recovery Image and Bootable Disk

before beginning to use your system. To do so, follow the instructions in the “Creating a

Backup of Bootable Disk and Recovery Image” section of this document.

It is also important that you create a copy of the software that is essential for your system to access the

internet (hereafter called “essential access software”) to external writable media or an external drive.

To do so, follow the instructions in the “Creating a Backup of the System-Speciﬁc Software Drivers”.

Creating a Backup of Bootable Disk and Recovery Image

When you purchased your new system, a copy of the recovery image was loaded into a

hidden partition on your hard disk drive. Having a copy of the recovery image available to

you means that in the event of system failure, you will be able to restore it and re-install

the essential access software using Fujitsu Software Auto Installer.

To make a copy of the recovery image to DVD disks, you will need three or four blank

disks to create the copy. After creating the copy, be sure to label the disks and keep

them in a safe place to ensure they do not get damaged.

Note: If your system does not have an internal writable DVD drive, connect your

system to an external drive* before beginning the following steps.

1. Launch System Restore and Recovery from the desktop icon. It will allow you to create

the Bootable Disk and the Recovery Image Disk Set.

2. On “Step 1: Select the Bootable Disk from the list”:

a. Select a media type.

b. Notice the number of disks that are needed for the set.

c. Click Next to proceed.

3. On “Step 2: Conﬁrm your Recovery Disk”, click Next.

4. On “Step 3:” follow the on-screen instructions to make the disk or disk set, then click

Start. It takes approximately 20 minutes to make one disk.

5. On “Step 4”, when the disk creation is completed, a message appears.

Click Finish to exit the program.

6. Repeat Step 1: Select Recovery Disk from the list and repeat the above

steps 2(a), 2(b), 2(c), 3, 4 and 5.

* DEPENDING UPON YOUR OPTICAL DRIVE AND MEDIA FORMAT USED, SOME MEDIA

TYPES MAY BE INCOMPATIBLE FOR CREATING IMAGE BACKUPS.

108 Fujitsu

Appendix

Creating a Backup of Essential Access Software

When you purchased your new system, a “Fujitsu Software Extractor” shortcut was loaded to

“C:\Fujitsu\Drivers\AutoInstaller\”. This shortcut allows you to save the software driver packages

along with the extracted Auto Installer software package to a selected location. It is recommended

that you save these packages to writable media or an external drive. This ensures that in the

event of system failure you will be able to re-install the essential access software.

1. Open the C:\Fujitsu\Drivers\AutoInstaller\ folder

2. Run “Fujitsu Software Extractor” as an Administrator

a. Right-click on Fujitsu Software Extractor.

b. Select the “Run as Administrator” option from the menu that is displayed.

3. The default save location is C:\Fujitsu\ AutoInstaller\ Drivers\. You can change the location

by clicking on the Browse button and selecting your preferred location.

Note: It is recommended that you change the default location and save the

software packages to the external writable media or drive.

4. Click on the Save Packages button.

5. Fujitsu Software Extractor copies the zipped software packages and Readme ﬁles,

and extracts the Auto Installer folder to the selected location.

Note: The extracted Auto Installer will later be used to install the software

automatically on the system in the event of generic image restoration when

the software is not pre-installed in the image.

RECOVERYOURSY

STEM WHEN THE HARD

DRIVE IS STILL ACCESSIBLE

Using the Recovery and Utility Tools

The Recovery and Utility tools consist of a variety of tools that will help you recover your

recovery image and system images, and delete the data from your hard disk.

Methods for accessing the utilities

Recovery and Utility Tools are preinstalled in a hidden partition by the factory, or

they can be accessed by using the bootable disk.

Note: The Recovery and Utility tools may be deleted from your hard disk

drive if you modify the partitions. If that occurs, you will not be able to

use the hidden partition for booting to Recovery and Utility Tools, but you

will still be able to boot from the Bootable Disk.

Fujitsu 109

Appendix

Determining whether Recovery and Utility is pre-loaded

1. Turn on or reboot your system. When the Fujitsu logo appears, press the F12 key.

2. Use the Ta b key to get to the Application Menu.

3. Check whether the Recovery and Utility option is present. If it is not present, it means

that the utility must be used from the Bootable Disk. Proceed to “Running Recovery and

Utility from the Bootable Disk” if Recovery and Utility is unavailable.

Running Recovery and Utility from hard disk

1. Turn on or reboot your system. When the Fujitsu logo appears, press the F12 key.

2. Use the Ta b key to get to the Application Menu.

3. Cursor down to Recovery and Utility and press the Enter key.

4. Choose your language, if necessary. Select Recovery and Utility to proceed.

5. Three tool options appear: Diagnostics,Recovery,andUtility (refer to the Recovery and

Utility tools section below for instructions on how to use these tools).

6. If this was successful please skip the next step and go to “Recovery and Utility tools.”

7. If this was NOT successful, please go to the next step.

Running Recovery and Utility from the Bootable disk

To verify/change the boot-up priority (rather than booting-up from the hard drive or

an external media drive), perform the following steps:

1. Power on your system. When the Fujitsu logo appears on the screen, press the F12 key.

2. Insert the bootable disk into the drive tray.

3. Highlight the CD/DVD option from the Boot menu, then press Enter .

4. Click OK.

5. Select CD/DVD boot mode: UEFI Mode, if applicable, and then press Enter .

While the ﬁles are being loaded from the disk, the Fujitsu logo screen will appear

followed by a progress bar at the bottom of the screen.

110 Fujitsu

Appendix

Recovery and Utility tools

Note: Recovery and Utility tools may not be available on your system depending

on the region from which the system was shipped.

Diagnostics tool: The Diagnostics tool is designed for use by IT professionals. It is not likely you

will need to use this tool. If you should need to use this tool, perform the following steps:

1. Press the Diagnostics Tool button to start the Diagnostics tool.

2. Read the note, and then click OK.

3. Choose one or more of the following options for diagnostics on the Fujitsu Hardware Diagnostics

Tool window: CPU, Memory, Display, Hard Disk, CD/DVD/BD, Floppy Disk, Keyboard, and Mouse.

4. Click the Option button in the Tool menu to specify how many times the tool

should run diagnostics on each selected component.

5. Press Execute to start the Diagnostics tool.

6. After the execution is completed, the selected components are circled in red to indicate that they

have been diagnosed and the result dialog window opens. Click Close to close the window.

7. Click End to close the Diagnostics tool, and then click Yes to conﬁrm the end of diagnostics session.

Recovery tool: The Recovery tool contains two options:

• Restore C Drive: Restore recovery image (only C: drive)

• Restore Full Hard Drive: Restore recovery image (full hard drive).

You can use these tools to restore the Recovery Image from the hidden partition, and perform a full

hard drive recovery. Please refer to instructions above for details on how to create a Recovery Image.

Restore the Recovery Image from Hidden Partition

1. Click [Restore C: drive] from Recovery and Utility tools

2. The progress bar is followed by “Restore Recovery image (only C: drive)” screen

conﬁrming that the Image will be restored to the C: drive. Click Next.

3. Read the instruction screen and select Agree,thenclickNext.

4. Click OK to acknowledge the warning message to restore recovery image to the C: drive.

5. When the progress bar appears, wait for the process to complete.

6. Click Finish when the process completes; the computer will restart to Windows.

7. Follow the steps listed in the “Auto Installation support for software packages

from hidden partition” section.

8. Download FSDM (Fujitsu Software Download Manager) from the support site and download

all the software applicable to the model and OS using FSDM.

9. Follow the steps listed in “Auto Installation support for software packages

downloaded from support website” section.

Fujitsu 111

Appendix

RECOVER YOUR SYSTEM WHEN THE HARD

DRIVE IS NOT BOOTABLE

Restore the Recovery Image for Full Hard Drive

Follow the steps in the “Recovering your Recovery Image using Recovery and

Utility (for new hard drive or non-bootable hard drive)” section. You will need the

Bootable Disk and the Recovery Disk Set for this task.

Utility tool: If applicable for your region, the Utility tool contains two options:

Hard Disk Data Delete and Partition Creation.

The Hard Disk Data Delete utility is used to delete all data on the hard disk

and prevent the data from being reused.

NOTE: Do not use the Hard Disk Data Delete utility unless you are absolutely certain

that you want to erase your entire hard disk, including all partitions.

To delete hard disk data:

1. Click the Hard Disk Data Delete button. The progress bar appears, followed by the EULA screen.

2. Agree to the EULA and click Next.

3. Choose the hard disk from which the data should be deleted in the list of hard disks and click Next.

The Partition Creation utility is used to change the C: and D: drive partition sizes.

To run this utility: (This is not an option when using Windows 7.)

1. Click the Partition Creation button.

2. A progress bar appears, followed by the EULA screen. Agree to the EULA.

3. On the Recovery Tool - Partition Creation screen, move the slider to set disk size, and then click OK.

4. Click Yes in the Partition Creation conﬁrmation dialog.

WARNING: It is highly recommended that you send your product to Fujitsu

Service to replace a hard drive. A mistake could possibly destroy your

computer, your new hard drive or both.

112 Fujitsu

Appendix

Recovering Your Recovery Image Using Recovery and Utility

(for new hard drive or non-bootable hard drive)

If you have installed a new hard drive or your hard drive is not bootable, perform the following steps.

Note: You will need the Bootable disk and Recovery Image disk set for this recovery.

1. Power on your system. When the Fujitsu logo appears on the screen, press the Enter key.

2. Insert the bootable disk in your DVD drive, then click OK.

3. Highlight the CD/DVD option from the Boot Menu and press Enter .

4. Select CD/DVD boot mode: Select UEFI Mode, if applicable and press Enter .

While the ﬁles are being loaded from the disk, the Fujitsu logo screen appears

followed by a progress bar at the bottom of the screen.

5. Choose your language, if necessary.

6. Three tool options appear: Diagnostics,Recovery and Utility. Select Recovery.

• For Windows 8.1: Select Restore full hard drive

• For Windows 7: Select Restoring the Factory Image (full hard drive recovery)

7. Click Next to conﬁrm full hard drive restoration. All data on HDD will be deleted.

8. Agree to EULA by selecting Agree option and clicking Next.

9. Click Next on the Recovery Disk Check screen to verify that the bootable

disk has been inserted into the optical drive.

10. The Checking for Recovery Disk screen appears followed by the prompt to insert the

ﬁrst disk. Click OK to continue. Repeat this step for all disks. After all recovery disks

have been checked and the check has been completed, click Next.

11. Follow the prompt to reinsert the ﬁrst recovery disk and click Next.

12. Click OK when you receive the ﬁnal warning informing you that all data on drive

C will be lost. This starts the recovery process.

13. Follow the prompts to insert the next recovery disks and click OK.

14. After the copying of the image to the HDD completes the restore process is

complete, click Finish to restart the system. The computer will restart automatically

and then go through the ﬁrstbootprocess.

15. Follow the steps listed in “Auto Installation support for essential access

software from backup location” section.

16. Download FSDM (Fujitsu Software Download Manager) from support site and download

all the software applicable to the model and OS using FSDM.

17. Follow the steps listed in “Auto Installation support for essential access

software downloaded from support website.

Fujitsu 113

Appendix

Installing the Software after the Recovery Image is Restored

Auto-installation support for essential access software

from hidden partition

The below listed steps are applicable only in cases in which the recovery image restore

and hidden partition contents have not been wiped out.

1. After the recovery image is restored, launch the desktop icon “Fujitsu Software Auto Installer”.

2. Double-click on “Fujitsu Software Auto Installer” desktop icon.

3. Click Yes on User Account Control Dialog box. This will take some time to

process the software packages. A message will be displayed during this time,

“Please wait while the content is being processed”.

4. If EULA is displayed for Fujitsu Software Auto Installer, accept the EULA, otherwise continue.

5. Then Fujitsu Software Auto Installer user interface will be launched providing ability

to auto-install the essential access software on the system.

6. It is recommended that you install all the software in the listed order. You can

Select All, to install the software in the order listed.

7. Click Install to start the installation.

8. After installing all the selected drivers, Installation Results window will be displayed. Click OK.

9. “You must restart the system for the settings to take effect. Do you wish to

reboot now?” message appears. Select Yes.

10. The system will now reboot.

11. You can now connect to the internet and download FSDM (Fujitsu Software Download

Manager) from the support site and download all the software applicable to the

model and OS using FSDM if they are not downloaded yet.

114 Fujitsu

Appendix

Auto-installation support for essential access software

from backup location

The below listed steps are applicable in cases in which a backup copy was created as

mentioned in the section “Creating a Backup of essential access software”.

1. It is important to have the extracted Auto installer software package folder

and Readme ﬁle in the same location as other software folders. Otherwise

auto-installation of the software will not be supported.

2. Inside the Auto Installer software package, launch FjAutoinstall.exe as an Administrator.

3. Click Yes on the User Account Control dialog box. This will take some time to

process the software packages. A message will be displayed during this time stating,

“Please wait while the content is being processed”.

4. If EULA is displayed for Fujitsu Software Auto Installer, accept the EULA, otherwise continue.

5. The Fujitsu Software Auto Installer user interface will be launched providing ability

to auto install the essential access software on the system.

6. It is recommended that you install all the software in the listed order. You can

“Select All”, to install the software in the order listed.

7. Click the Install button to start the installation.

8. After installing all the selected drivers, Installation Results window is be displayed. Click OK.

9. “You must restart the system for the settings to take effect. Do you wish to

reboot now?” message appears. Select Yes.

10. The system will now reboot.

Auto Installation support for the software downloaded from support website

1. Download FSDM (Fujitsu Software Download Manager) from the support site and download all

the drivers applicable to the model and OS using FSDM if they are not downloaded yet.

2. When the software packages are downloaded from web, it is important to download

the Auto Installer Software package and the model/language- speciﬁc Readme

ﬁle if you prefer to auto install the software.

3. It is important to have the extracted Auto Installer software package folder

and Readme ﬁle in the same location as other software folders. Otherwise

auto-installation of the software will not be supported.

4. Inside the Auto Installer software package, launch FjAutoinstall.exe as administrator.

5. Click Yes on the User Account Control dialog box. This will take some time to

process the software packages. A message will be displayed during this time stating

“Please wait while the content is being processed”.

6. If EULA is displayed for Fujitsu Software Auto Installer, accept the EULA, otherwise continue.

7. The Fujitsu Software Auto Installer user interface will be launched providing the ability

to auto install the software downloaded from support site.

8. It is recommended that you install all the software in the listed order. You can

Select All, to install the software in the order listed.

9. Click the Install button to start the installation.

10. After installing all the selected drivers, the Installation Results window is displayed. Click OK.

11. “You must restart the system for the settings to take effect. Do you wish to

reboot now?” message appears. Select Yes.

12. The system will now reboot.

Fujitsu 115

Appendix

Downloading Driver Updates

To ensure that you always have the most current driver updates related to your system,

occasionally access the Fujitsu Software Download Manager (FSDM) utility. The FSDM

utility is available from the Fujitsu Support site. FSDM will allow you to view and

download a list of the most current drivers, utilities, and applications to determine whether

you have the latest versions. To download the FSDM Utility, go to the Support Site:

"http://support.fujitsupc.com/CS/Portal/support.do?srch=DOWNLOADS".

If you are planning on downgrading, upgrading or changing versions of your operating system during

this process please see the User’s Guide for more information at "http://solutions.us.fujitsu.com".

116 Fujitsu

Index

A beep sounds every second 82

AC adapter

connecting 18

Set up 18

Acoustic warnings 87

Activate

keyboard backlight 44

Alt+Tab 45

Anti-theft protection 65

Audio connections 77

Back tab 45

Backspace 42

Backspace key 42

Battery 48

battery charge 52

Caring for and maintaining 48

charge level 48

Charging 48

Discharges too quickly 86

see Rechargeable battery 48

Self-discharge 48

Service life 48

Storing 48

battery charge meter 48

BIOS Setup Utility

, protecting with password 66

calling 79

exiting 80

operation 79

Settings 79

Blank LCD screen 82

Bluetooth

switching module off 55, 104

switching module on 55, 104

Bluetooth, Safety notes 13

Caps Lock 42

Caps Lock key 42

Charge capacity, battery 48

Charging back-up battery 82

Choose a location 18

Clickpad 39, 44

buttons 39

Deactivating 44

Dragging items 40

Executing commands 39

Moving the pointer 39

Selectinganitem 39

Clickpad buttons 44

Components

Installing/Removing 78

Conﬁguration, BIOS Setup Utility 79

Conﬁguring hardware 79

Conﬁguring system 79

Connecting audio devices 77

Connecting headphones 77

Ctrl+Alt+Del 45

Cursor control 42

Cursor keys 42

Date not correct 82

Deactivate

keyboard backlight 44

Declaration of conformity 97

Devices,

connecting 72

disconnecting 72

Display orientation

select 27

DOC (INDUSTRY CANADA) NOTICES 95

Ending

energy saving mode 85

Energy

Energy consumption 52

Energy saving 13

Energy saving functions 52

Enter 42

Enter key 42

Error messages on the screen 88

Errors

Acoustic warnings 87

Screen messages 88

Ethernet LAN 57

Factory Image 81

Fault

correction 81

Fingerprint sensor 65

conﬁguring 65

First-time setup 17

Fn key 42

Fujitsu 117

Index

Fn+F10 45

Fn+F2 44

Fn+F3 44

Fn+F4 44

Fn+F5 44

Fn+F6 44

Fn+F7 44

Fn+F8 44

Fn+F9 45

Getting started 17

Hard disk:

restoring the contents 81

HDMI port 73

Important notes 12

In case of service 78

Incorrect time 82

Information,

safety 12

Kensington Lock Cable 65

Key combinations 44

Keyboard 41

keys 41

Landscape format

display 27

LCD screen

Decrease brightness 44

difﬁcult to read 83

Notes 31

reﬂected glare 83

Remains blank 82

Line feed 42

Making ready to use 18

Mechanical security 65

Memory card

handling 53

inserting 53

removing 53

Microphone 54

Mobile operation 14

Monitor

connection 74

no image 83

remains blank 83

unstable image 83

Monitor connection

see VGA socket 74

Notebook

before traveling 14

does not start 84

not working 85

operating 21

switching off 29

transporting 14

Notebook: switching on 24

Notes 12

disposal / recycling 95

Energy saving 13

LCD screen 31

Transport 14

Num Lock

indicator 43

Number keypad 41

Numeric keypad 41

see Virtual number keys 43

Operating system

activating system protection 67

cancel system protection 67

Protecting with password 67

Operating system, recovering 81

Operation, notebook 21

Packaging 17

Password

changing 67

entering 66

removing 67

Password protection 66

hard disk 68

Pen 35

Peripherals,

connecting 72

disconnecting 72

Port replicator

Ports 58

118 Fujitsu

Index

Portrait format

display 27

Ports

Port replicator 58

Power saving 13

Power-on indicator 24

Printer does not print 85

Radio components

Safety notes 13

Rechargeable battery

see battery 48

Return 42

Safety information 12

Screen brightness

Decrease 44

Increase 44

Screen connection

see VGA socket 74

Security functions 63

SmartCard 69

SystemLock 69

Self-discharge, battery 48

Service life, battery 48

Set up

Device 18

Setup

see BIOS Setup Utility 79

Shift 42

Shift key 42

Shift+Tab 45

Slot

Memory cards 53

Speaker 54

Status indicators 21

Subwoofer 54

Summer time 82

Supervisor HDD password

changing 67

Supervisor password

entering 66

removing 67

Suspend/Resume button 24

Switch off

speakers 44

Switch on

speakers 44

Switching between screen outputs 45

Switchingonfortheﬁrst time 19

Symbols

Indicators 21

System settings, BIOS Setup Utility 79

Tab key 42

The wireless connection to a network

does not work 85

Time not correct 82

Tips 81

TPM 71

Transport 14

Damage during transportation 17

Traveling, notebook 14

Troubleshooting 81

Trusted Platform Module 71

USB charging function 76

USB ports 75

User HDD password

changing 67

User password

entering 66

removing 67

Using the security lock 65

VGA socket 74

Virtual number keys 43

Volume

increase 45

reduce 44

Volume control 54

Webcam 47

Windows key 42

Winter time 82

Wireless components 44

Wireless LAN

Safety notes 13

switching module off 55, 104

switching module on 55, 104

Wrong date/time 82

Fujitsu 119

Table of Contents

Fujitsu T904 User Manual

Related Manuals