Glyph StudioRAID User Manual
Displayed below is the user manual for StudioRAID by Glyph which is a product in the Disk Arrays category. This manual has pages.
Related Manuals
StudioRAID™ Manual
Tabletop FireWire 800, USB 3.0 and
eSATA enclosure with RAID 1 and RAID 0
Proprietary Notice and Disclaimer
Unless noted otherwise, this document and the information herein disclosed are proprietary to Glyph Technologies, 3736
Kellogg Rd., Cortland NY 13045 (“GLYPH”). Any person or entity to whom this document is furnished or having possession
thereof, by ac-ceptance, assumes custody thereof and agrees that the document is given in confidence and will not be copied or
reproduced in whole or in part, nor used or revealed to any person in any manner except to meet the purposes for which it was
delivered. Additional rights and obligations regarding this document and its contents may be defined by a separate written
agreement with GLYPH, and if so, such separate written agreement shall be controlling.
The information in this document is subject to change without notice, and should not be construed as a commitment by GLYPH.
Although GLYPH will make every eort to inform users of substantive errors, GLYPH disclaims all liability for any loss or damage
resulting from the use of this manual or any software described herein, including without limitation contingent, special, or inci-
dental liability.
© 2015 Glyph Technologies. All rights reserved. Specifications are subject to change without notice. Glyph and the
Glyph logo are registered trademarks of Glyph Technologies. All other brands and product names mentioned are trademarks
of their respective holders.
Contacting Glyph
Please use the following contact information to contact Glyph and its distributors.
Glyph USA offers phone support Monday through Friday, 8:00 am to 5:00 PM Eastern
Time.
Note: DO NOT ship any return goods to the mailing addresses below unless you have a valid RMA number.
All goods will be refused delivery unless a valid RMA number is displayed on the outside of the package.
United States of America
Glyph Technologies
3726 Kellogg Rd.
Cortland, NY 13045
USA
Phone: +1 607-275-0345
Fax: +1 607-275-9464
www.glyphtech.com
Sales Contact
sales@glyphtech.com
Technical Support:
tech@glyphtech.com
Unpacking Your StudioRAID
Your Glyph StudioRAID and accessories are packaged in a sturdy shipping container. Please inspect the
con-tainer for evidence of shipping damage and mishandling. If the container is damaged, file a report with
the carrier or dealer immediately. Do not attempt to unpack and operate your StudioRAID until the carrier
or dealer confirms the damage. If the container is in good condition, proceed with unpacking the
StudioRAID. Verify that all of the items described in the next section are present and in good condition. If
any of the items you expect to find in your container is missing or damaged, contact the dealer before
proceeding any further.
In any case, do keep the shipping container and all packing materials in a safe place.
The StudioRAID package includes:
StudioRAID Enclosure
FireWire 800 Cable
USB 3.0 Cable
IEC Power Cable
About the StudioRAID and Drive Modes
The StudioRAID enclosure contains two hard disk drives, which function as one single volume. It supports
two drive modes: RAID 1 (mirroring) and RAID 0 (striping). Each drive mode has its own advantages,
depending upon the application.
RAID 1 (mirroring) oers data redundancy and real-time backup by writing the same data to the
two hard drives at the same time. Should a drive failure happen, data is still available on the remain-
ing drive. In RAID 1 mode, the two drives are seen by the computer as one volume, but with half the
capacity. For example, a 1TB StudioRAID will be seen as a 500GB drive. Reading and writing occurs
on both drives simultaneously so that each of the drives contains exactly the same data, mirroring
each other. If either of the drives should fail the other is there to seamlessly continue to provide
operation.
RAID 0 (striping) increases the performance of the drive system by spreading the data across two
drives. RAID 0 is a proven technology for editing video, working with huge graphics les, sound
libraries, and streaming instruments that play hundreds of samples simultaneously. RAID 0 is the de-
fault shipping drive mode. In RAID 0 (striping) mode, the two drives are seen by the computer as one
large drive, and reading and writing occurs on both drives simultaneously. It is designed to increase
the performance and data throughput of the drive system. The StudioRAID's built-in RAID controller
splits each piece of data across both of the drives in segments and distributes the I/O burden. Since
data is written without any form of parity data-checking, it allows for the fastest data transfer of all
other RAID levels. However, if one drive becomes damaged, the data on both drives can become
cor-rupted. RAID 0 is not redundant or fault tolerant like RAID level 1, but the trade off is that it’s the
fastest of all RAID levels. MAKE SURE TO BACKUP YOUR DATA OFTEN!
Using the StudioRAID with Windows 7, 8, & Above / XP
Older versions of Windows, such as XP 32-bit, use Master Boot Record which doesn’t support volumes
larger than 2TB. When the total capacity of the RAID is 2TB or higher, you must format the array using GPT in
Windows. GPT format is only supported by Windows XP 64-bit Edition, Windows 2003 Server, Windows
Vista, Windows 7, 8, 8.1, and Mac OS X. GPT format will not work with XP 32-bit or older Windows operating
systems. If you want to use Windows XP 32-bit, your total capacity must be less than 2TB in RAID 0 or less
than 4TB in RAID 1.
StudioRAID Ports
The fastest interface on the StudioRAID is eSATA and there is one eSATA port on the rear panel. In RAID 0
mode, the StudioRAID can sustain over 200MB/sec (read speed) when connected via eSATA to a fast eSATA
card such as the Glyph/Highpoint 2642. FireWire 800 is another option and there are two FW800 ports on
the rear panel alongside USB 3.0. Officially, these IEEE 1394b ports run at up to 800Mbits/sec. If using
FW800, one of these ports should be connected to your computer, and the other should be connected to
other downstream FireWire devices. It doesn’t matter which port you connect to the computer, they are
functionally identical. If your computer has a FireWire 400 port only, you can use a FW400 to FW800 adapter
cable, which is available from Glyph. If your computer doesn’t have any FireWire ports you can either
purchase an eSATA or FireWire adapter card (recommended), or use the USB 3.0 port on the back of the
StudioRAID.
Front panel LED
The StudioRAID front panel has a single bi-color LED. The LED will display solid blue when power is on. The
LED will flash blue when there is disk activity. The LED will flash or display a solid red color when error
conditions exits with the drives inside the array. Those error conditions are discussed in greater detail
below.
NOTE: It is normal for the LED to flash red when the unit is powered on. Since the drives inside the
StudioRAID take a few seconds to spin up, they are “offline” for a moment when the controller looks for them,
and the red warning LED comes on. When they fully spin up the controller sees that everything is normal,
and turns the red LED off.
Setting up the StudioRAID
1. Position the StudioRAID by placing the unit on a flat, level surface, or install the unit into a rack with one of
Glyph’s rack kits. Caution: Speakers are magnetic devices; they can harm your data if they’re too close to your
hard drives or tapes.
2. Connect the power cable. Make sure that the power is off on all of your computer equipment and the
StudioRAID. Connect the power cable to the back of the StudioRAID. Plug the three-prong plug
into an appropriate power receptacle, preferably with surge and spike protection.
3. Connect the FireWire 800, USB, or eSATA cable. Plug one end of the cable into your computer’s port, and
the other into the back of the StudioRAID. Both FireWire 800 ports are functionally identical, so it doesn’t
matter which one you use.
StudioRAID Quickstart
Here are instructions for changing the RAID mode of your StudioRAID.
Note: By following these instructions you will be erasing any data previously stored on the StudioRAID.
Please back up before proceeding.
-If connected, safely eject StudioRAID from your desktop.
-Power off StudioRAID and disconnect all FireWire, USB, and eSATA cables from the unit.
-Move the recessed switch to your desired setting on the rear of the device, either a RAID 0 or RAID 1.
You may need to use a paper clip or similar tool as the switch is recessed.
-Next, connect the power adapter only. Do not power on the StudioRAID yet.
-Using a paper clip or other tool, press and hold the "SET" button on the back panel.
-While continuing to hold the "SET" button, power on your StudioRAID and slowly count from 1 to 10.
-Release the "SET" button and reconnect your USB 3.0, FireWire, or eSATA cable to the StudioRAID.
That's it! Your StudioRAID should now show up in Disk Utility (on Mac) or Disk Management (on Windows)
and be ready to format. You can always call us at 800-335-0345.
4. Power up the StudioRAID and power up your computer.
5. If you’re using Mac OS X, the icon should mount on your desktop. If you’re using Windows, please follow
the formatting instructions for Windows later in this manual.
1. Right-click My Computer and click Manage.
2. In the Computer Management window, under Storage, click Disk Management.
3. In Disk Management, right click the Unallocated partition. Click "New Simple Volume" and the Write
Signature Wizard pops up.
4. Use the wizard to write a signature to the new drive. If you want only one partition we suggest using a
primary partition and selecting the maximum size. In most cases you’ll want to use NTFS volumes, this is
the default for Windows XP and Vista. Ensure "Perform a Quick Format" is checked. Choose FAT32 if you
want to use the drives with older versions of Windows, or if you want to use the drive with Windows and
Mac OS.
5. Formatting will take a few minutes, after which your drive will be ready to use.
*Note - Formatting for Windows 8 and above is the same once you are in Disk Management.
Formatting Instructions
Windows XP / Vista / Windows 7 Formatting Instructions
*For most cases, you'll want to be sure to initialize your device in GUID Partition Table (GPT).
Mac OS X Formatting Instructions
Since your StudioRAID comes pre-formatted for Macintosh you don’t need to format them on installation. If
you decide to reformat or partition your drive at a later date, use Disk Utility (supplied with the Mac OS X
operating system).
Caution: This procedure will destroy any data currently on the drive. Before formatting a drive, save any important
data it contains.
1. Open Disk Utility:
-Double click on your internal hard drive mounted on the desktop
-Open Applications Folder > Utilities Folder > double click on Disk Utility
2. Select your StudioRAID drive from the list on the left. The top entry represents the device and the entry un-
derneath it represents the volume associated with that device. Click on the top device which will say some-
thing like “XXXGB Glyph Technologies”.
3. Click the “Partition” tab on the right side of the screen.
4. Change "Current" to "One Partition" (recommended).
5. Choose the desired volume format from the drop-down list. Glyph recommends the default “Mac OS Ex-
tended (Journaled)”.
6. Click in the “Name” field and type the desired name for the drive. This name will identify the drive on the
desktop.
7. Click the “Install Mac OS 9 Disk Driver” button (if applicable) if you would like your drive to be compatible
with OS 9.
8. Click the "Options" button. Select "GUID Partition Table". Click "OK".
9. Click the “Partition” button to partition your drive. Click "Partition" in the dialogue box that appears. Your
new drive should automatically mount on the desktop as a Glyph volume.
More Information
StudioRAID Features
Brushed, stainless steel face plate 1/8” thick (3MM)
Scratch-resistant black powder-coated aluminum chassis
Engineered to support professional audio and video
Supports two software-selectable drive modes: RAID 1 and RAID 0.
Internal power supply, no wall wart, internal quiet fan
3 Year Warranty
2 Year Free Basic Data Recovery
Advance Replacement in 1st year of warranty within U.S. Continental 48 States only.
StudioRAID Specifications
Part Number
Interfaces
Maximum Transfer
Rate Dimensions
Configuration Weight
Internal Power Supply
OS Compatibility
Warranty
SRxxx (xxx is equal to total capacity)
(2) 9-pin FW800 rear ports
(1) eSATA rear port
(1) USB 3.0 Hi-speed rear port
eSATA: 300MB/sec (3Gb/sec)
H 1.7” x W 8.6” x D 9.5”
Desktop enclosure (rack mount optional) 5.9 lb. / 2.7 kg
Universal 100-240v 50/60 Hz
Mac OS 10.4 and above
Microsoft Windows XP, Vista, 7, Windows 8 and above, Modern Unix
based, Linux, or BSD
3 Years
1 Year Overnight Advance Replacement
2 Years Free Basic Data Recovery. Microsoft Windows XP, Vista, 7,
Windows 8 and above, Modern Unix based, Linux, or BSD
Content Creation Applications
Qualied with Final Cut Pro, Avid Xpress, Adobe Premiere.
Qualied with all major audio production packages that support FireWire storage, including Digidesign Pro
Tools, Steinberg Nuendo and Cubase, Apple Logic, MOTU Digital Performer, Cakewalk Sonar, Sony Vegas and
more...
Conguration
The StudioRAID can be rack mounted in a standard 19-inch rack with Glyph’s optional rack kits. There is a
single kit (part# GPT-RACKMOUNT KIT v2) for mounting one drive, and a dual kit (part# GPT-RACKMOUNT
KIT v2) for mounting two drives. The dual kit allows any two of Glyph’s StudioRAID Series tabletop drives to
be mounted in a double rack space.
About eSATA
• eSATA is an external interface technology that grew from the internal SATA I interface.
• The StudioRAID's eSATA port supports speeds up to 3 Gb/sec (300 MB/sec), much faster than FireWire 400 or
FireWire 800.
• Shielded eSATA cables up to 2 meters in length are available.
• eSATA cables are dierent than SATA I cables, they are shielded and cannot be used with internal SATA I
connectors.
• eSATA uses a “point-to-point” connection, therefore each eSATA drive needs to be connected to its own
eSATA port.
• Most computers do not have built-in eSATA, so you’ll need a PCI card to connect your drive with eSATA.
Glyph sells various eSATA cards.
About FireWire 800
• FireWire 800 supports speeds up to 800 Mb/sec, twice as fast as FireWire 400.
• If your computer does not have built-in FireWire 800, you’ll need a PCI card to achieve a true FireWire 800
connection.
• Most 800 ports are Bi-Lingual, which means they speak both FireWire 400 and FireWire 800.
• If you connect a 400 device to an 800 device, you will be running at 400 speed maximum.
• FireWire is forward-compatible and back-compatible, but the bus always runs at the speed of the slowest
link.
•Cables are used to connect 800 devices to 800 devices.
• Bi-Lingual cables are available to connect 400 devices to 800 devices.
• Bi-Lingual cables have a 9-pin Bi-Lingual connector at one end and a 4-pin or 6-pin FireWire 400 connector
at the other end