Hoover HDIN 4D620PB-80E User Manual

Displayed below is the user manual for HDIN 4D620PB-80E by Hoover which is a product in the Dishwashers category. This manual has pages.

Related Manuals

Hoover HDIN 4S613PS-80 Manual

Hoover HDIN 2L360PB-80 Manual

Hoover HDIN 4D620PB-80 Manual

Hoover HDIN 4D620PB Manual

Hoover HDIN 4S613PS Manual

Hoover HDIN 4S613PS-80E Manual

Hoover H3WS4428TAMCE-S Manual

Hoover ND4 H7A2TSBEX-S Manual

Thank you for choosing this product.

We are proud to offer the ideal product for

you and the best complete range of home

appliances for your daily routine.

Carefully read this manual for correct and

safe appliance use and for helpful tips on

efficient maintenance.

Only use the dish washer

after

carefully reading these instructions. We

recommend you always keep this manual

to hand and in good condition for any

future

owner.

Please check that the appliance is

delivered with this instruction manual, the

warranty certificate, the service centre

address and the energy efficiency label.

Each product is identified by

a unique 16

digit code, also called the “serial number”,

printed on the warranty

certificate or on

the serial plate found inside the door, on

the upper right hand side. This code is a

sort of product

specific ID card that you

will need to use to register the product or

if you need to contact the Technical

Assistance Centre.

Fig. A

GENERAL SAFETY RULES

WATER CONNECTION

LOADING THE SALT

ADJUSTING THE UPPER BASKET

(ONLY ON SOME MODELS)

LOADING DISHES

INFORMATION FOR TEST

LABORATORIES

LOADING THE DETERGENT

TYPES OF DETERGENT

LOADING THE RINSE AID

10.

CLEANING THE FILTERS

11.

PRACTICAL HINTS

12.

CLEANING AND MAINTENANCE

13.

DESCRIPTION OF THE CONTROL

PANEL

14.

TECHNICAL DATA

15.

PROGRAMME SELECTION AND

SPECIAL FEATURES

16.

REMOTE CONTROL (Wi-Fi)

17.

PROGRAMME LEGEND

18.

WATER SOFTENER UNIT

19.

TROUBLESHOOTING AND WARRANTY

20.

ENVIRONMENTAL CONDITIONS

Contents

1. GENERAL SAFETY

RULES



This appliances is intended to

be used in household and

similar applications such as:

− Staff kitchen areas in

shops, offices and other

working environments;

− Farm houses;

− By clients in hotels, motels

and other residential type

environments;

− Bed and breakfast type

environments.

A different use of this appliance

from household environment

or from typical housekeeping

functions, as commercial use by

expert or trained users, is excluded

even in the above applications. If

the appliance is used in a manner

inconsistent with this it may reduce

the life of the appliance and may

void the manufacturer’s warranty.

Any damage to the appliance or

other damage or loss arising

through use that is not consistent

with domestic or household use

(even if located in a domestic or

household environment) shall not

be accepted by the manufacturer to

the fullest extent permitted by law.

 for EU market

The appliance can be used by

those aged 8 or over and by

those with limited physical,

sensorial or mental capacities,

without experience or knowledge

of the product, only if supervised

or provided with instruction as

to the operation of the appliance,

in a safe way with awareness

of the possible risks.

 for Extra EU markets

This appliance is not intended

for use by persons (including

children) with reduced physical,

sensory or mental capabilities,

or lack of experience and

knowledge, unless they have

been given supervision or

instruction concerning use of

the appliance by a person

responsible for their safety.

 Children should be supervised

to ensure that they do not play

with the appliance.

 Children of aged 3 and under

should be kept away unless

continuously supervised.

 If the supply cord is damaged,

it must be replaced by a

Special cord or assembly

available from the manufactured

or its service agent.



Only use the hose-sets

supplied with the appliance for

the water supply connection

(do not reuse old hose-sets).



Water pressure must be

between 0.08 MPa and 0.8

MPa.



Make sure carpets or rugs do

not obstruct the base or any of

the ventilation openings.

 After installation, the appliance

must be positioned so that the

plug is accessible.



Do not leave the door open in

a horizontal position, in order

to avoid potential dangers (e.g.

tripping).



For further information on the

product or to consult the technical

data sheet, please refer to the

manufacturer's website.



For the maximum number of

place settings, see the relevant

data plate attached to the product



The technical details (supply voltage

and power input) are indicated

on the product rating plate.



Make sure that the electrical

system is earthed and complies

with all applicable laws, and

that the socket is compatible

with the plug of the appliance.

The manufacturer declines all

responsibility for any damage

to people or property due to

non-earthing of the machine.

 Ensure that the dishwasher

does not crush power cables.

 In general it is not advisable to

use adaptors, multiple plugs

and/or extension cables.

 Before cleaning or maintaining

the dishwasher, unplug the

appliance and turn off the

water supply.

 Do not pull on the power cord

or appliance to unplug the

machine.



Do not leave the appliance

exposed to the elements (rain,

sun, etc.).

 Leaning or sitting on the open

door of the dishwasher could

cause it to tip over.

WARNING:

Water may reach very high

temperatures during the

wash cycle.

WARNING:

The appliance must not be

supplied through an external

switching device, such as a

timer, or connected to a circuit

that is regularly switched on

and off by a utility.

Electrical connections and

safety instructions

 When moving, do not lift the

dishwasher by the door; during

the transport, never lean the

door on the trolley. We

recommend two people lift the

machine.



The dishwasher is designed for

normal kitchen utensils. Objects

that have been contamined by

petrol, paint, traces of steel or

iron, corrosive chemicals, acids

or alkalis must not be washed in

the dishwasher.



If there is a water softening

device installed in the home

there is no need to add salt to

the water softener fitted in the

dishwasher.



If the appliance breaks down or

stops working properly, switch it

off, turn off the water supply and

do not tamper with it. Repair work

should only be carried out by an

approved service agent and only

genuine spare parts should be

fitted. Any failure to follow the

above advice may have serious

consequences for the safety of

the appliance.

 If you need to move the

machine after removing the

packaging, do not try to lift it by

the bottom of the door. Open

the door slightly and lift the

machine by holding it on the top.

By marking this product,

we confirm, under our own

responsibility, full compliance

of this product with all

relevant safety, health and

environmental requirements

under European legislation.



Remove all elements of the

packaging.

 Do not install or use the

dishwasher if it is damaged.



Follow the instructions supplied

with the product.

WARNING:

Knives and other utensils

with sharp points must be

loaded in the basket with

their points down

or placed

in a horizontal position.

WARNING:

Keep packaging materials

away from children.

Installation

2. WATER CONNECTION



The inlet and drain hoses can be directed

to left or right.



Water pressure must be between 0,08

MPa and 0,8 MPa.



The inlet hose must be connected to a tap

so that the water supply can be cut off

when the machine is not in use (fig. 1 B).



The dishwasher is fitted with 3/4" threaded

connector (fig. 2).



Connect inlet hose "A" to water tap

"B"

with a 3/4" attachment making sure that it

has been properly tightened.



If it is necessary, the inlet pipe can be

lengthened up to 2,5 m. The extensio

pipe is available from the After Sales

Service Centre.



If the dishwasher is connected to new

pipes or to pipes which have not been

inuse for a long time run water through for

a few minutes before connecting the inlet

hose. In this way no deposits of sand or

rust will clog up the water inflow filter.

The dishwasher can be connected to

either cold or hot water, as long as it

is no hotter than 60°C.

The appliance must be connected to

the water mains using new hose-

sets.

The old hose-

sets should not be

reused.

SOME MODELS

may include one or more

of the following features:



WATERBLOCK (fig. 3)

The waterblock system has been designed

improve the safety of your appliance. The

system prevents flooding which might be

caused by

a machine malfunction or as a

result of a fracture on the rubber pipes

and in particular on the water supply pipe.

How it works

A sump located on the base of the appliance

collects any possible water leakage and

operates a sensor which activates a valve

placed under the water tap and blocks any

water, even with the tap fully opened.

box "A"

containing the electrical parts is

damaged, remove the plug from the socket

immediately. To ensure perfect operation of

the safety system, the hose with box "A"

should be connected to the tap as shown in

the

figure

. The water supply hose should

not

be cut, as it contains live parts. If the

hose is not long enough for correct

connection, it must be replaced with a longer

one. The hose can be obtained from the

Technic

al Assistance Centre.



AQUASTOP (fig. 4):

A device located on the supply tube that

stops water flow if the tube deteriorates;

in this case, a red mark will appear in the

window "A"

and the tube must be

replaced. To unscrew the nut, press the

one-way lock device "B".



AQUAPROTECT -

SUPPLY TUBE WITH

GUARD

(fig. 5):

Should water leak from the primary internal

tube "A"

, the transparent containment

sheath "B" will contain water to permi

the washing cycle to complete. At the

end of the cycle, contact the Customer

Service Centre to replace the supply

tube.

All the dishwashers are equipped with

an overflow safety device which, if

water exceeds normal levels due to

malfunctions, automatically blocks

water flow and/or drains excess

quantities.

Hydraulic safety devices



The outlet hose should disharge into a

standpipe, making sure that there are no

kinks (fig. 6).



The standpipe must be at least 40 cm

above floor level and it must have an

internal diameter of at least 4 cm.



It is advisable to fit an anti-

odour air trap

(fig. 6X)

. If necessary the outlet hose can

be extended up to 2,5 m, provided that it

is kept at a maximum height of 85 cm

above floor level. The extension pipe is

available from the After Sales Service

Centre.



The hose can be hooked over the side of

the sink, but it must not be immersed in

water, in order to prevent water from

being syphoned back to the machine

when this is in operation (fig. 6Y).



When installing the appliance under a

worktop the hose pipe cla

mp must be

attached to the wall in the highest

possible position under the worktop

(fig. 6Z).



Check that there are no kinks in the inlet

and outlet hoses.

Connecting the outlet hose

3. LOADING THE SALT

(Fig. A "1")

 The appearance of white stains on dishes

is generally a warning sign that the salt

container needs filling.

 On the bottom of the machine there is a

container for the salt for regenerating the

softener.

 It is important to use only a salt that is

specifically designed for dishwasher.

Other types of salt contain small

quantities of insoluble particles which

over a long period of time may affect and

deteriorate the softener performance.



To add salt, unscrew the cap of the

container on the bottom and then refill the

container.

 During this operation a little water will

overflow; but keep adding salt until the

container is full. When the container is

full, clean the thread of salt residue and

retighten the tap.

 After loading the salt, it is recommended

running a complete washing cycle, or

COLD RINSE programme.

 The salt dispenser has a capacity of

between 1.5 and 1.8 kg and, for efficient

use of the appliance, it should be refilled

from time to time .

(Only for first start up) When the

appliance is used for the first time,

after completely filling the salt

container, it is necessary to add water

until the container overflows.

After loading the salt, YOU MUST run

a complete washing cycle, or the

PRE-

WASH/COLD RINSE/REFRESH

programme.

4. ADJUSTING THE UPPER

BASKET (ONLY ON SOME

MODELS)



If 29 cm to 32.5 cm plates are regularly

used, load them onto the lower basket

after the upper basket has been placed in

its upper position, as detailed below

(according to the model):

Type "A":

1. Turn front blocks "A" outwards;

2. Remove the basket and remount it in

the upper position;

3. Replace blocks "A" in the original

position.

Dishes that are greater than 20 cm in

diameter can no longer be loaded onto the

upper basket, and the mobile supports

cannot be used when the basket is in the

upper position.

Type "A"

Type "B":

(ONLY MODELS WITH EASY CLICK):

1. Remove the upper basket;

2. Hold the basket on both sides and lift it

upwards (fig. 1).

Dishes that are greater than 20 cm* in

diameter can no longer be loaded onto the

upper basket, and the mobile supports

cannot be used when the basket is in the

upper position.

* In models fitted with a third basket, dishes

measuring more than 14 cm in diameter

can no longer be loaded onto the upper basket.

ADJUSTING THE BASKET TO THE

LOWER POSITION:

1. Hold the basket on both sides and lift it

gently upwards (fig. 1);

2. Then slowly release into the correct

position (fig. 2).

N.B.: NEVER LIFT OR LOWER THE

BASKET FROM ONE SIDE ONLY (fig. 3).

WARNING:

We recommend adjusting the basket before

loading the dishes.

Type "B"

5. LOADING DISHES

 The upper basket is provided with mobile

racks hooked to the sides of the basket,

which can be regulated into 4 positions.

 In the lowered position (A-A1) the racks

may be used for such items as: tea and

coffee cups, kitchen knives and ladles.

Also glasses with stems may be safely

hung on the ends of the racks.



In the upright position (B-B1) the racks

allow you to load dinner plates and soup

plates up to a maximum diameter of 19

cm. Plates should be loaded vertically

with the underside of the plate towards

the back of the dishwasher with a space

between each plate to allow water to pass

freely.



It is advisable to load large plates (approx.

26 or more cm) slightly tilted towards the rear

to facilitate introduction of the basket into the

machine.

 Salad bowls and plastic bowls may also

be loaded on the upper basket. It is

advisable to block these in place so that

the jets of water do not make them

overturn.

 The upper basket has been designed to

offer maximum flexibility in use and can

be loaded with up to 24 plates on two

rows, up to 30 glasses on five rows or a

mixed load.

A standard daily load is represented in

figs. 1

and 2.

Upper basket

(fig. 1)

Upper basket

(fig. 2)

 Saucepans, oven dishes, tureens, salad

bowls, lids, serving dishes, dinner plates

and soup plates can be loaded into the

lower basket.

Using the lower basket

Using the upper basket

 Place the cutlery in the plastic cutlery

holder with the handles pointing upwards

and place the cutlery holder on the lower

basket (fig. 6) making sure that the

cutlery does not get in the way of the

rotating arms.

 The lower basket is fitted with a special

adjustable central rack (fig. 3 and 4). This

permits stable and optimum loading, even

when the size and/or shape of the dishes

is non-standard.

- POSITION "A": for a standard load, or

one that excludes pans, salad bowls and

the like.

- POSITION "B": for dishes which, although

standard size, have a particular shape

(very deep bowls, square dishes or ones

without borders etc.).

- POSITION "C": for larger than average

flat plates and/or ones with non-standard

shapes (square, hexagonal, oval, pizza

dishes etc.).

 Smaller plates (used for dessert plates for

example), can also be placed into the

lower basket as shown in the figure 5,

with the support flap placed outwards

("E"). For normal or large plates the flap

must be in the position ("D").

Upper basket (fig. 5)

A standard daily load is represented in

fig. 6

Lower basket (fig. 6)

WARNING

If the small plates are placed in the

basket with the support flap

in the

incorrect position,

the plates will

interfere with the lower spraying arm

preventing it to rotate.

Please load the dishwasher sensibly to

ensure the best wash results.

The top of cutlery basket can be removed,

for enable various loading options (fig.7).

6. INFORMATION FOR

TEST LABORATORIES

Please ask information required for

comparison testing and measuring noise

levels, according to EN normative, to the

following address:

testinfo-dishwasher@candy.it

In the request, please specify model name

and number of the dishwasher (see rating

plate).

WARNING

Knives and other utensils with sharp

points must be loaded in the basket

with their points down or placed in a

horizontal position.

CUTLERY BASKET

(only on some models)

The lower basket has a safety-stop

device, for its safe extraction, also

especially useful with a full load. For

loadi

ng salt, cleaning filter and for

ordinary maintenance, the complete

extraction of the basket is necessary.

7. LOADING THE

DETERGENT

(Fig. A "2")

Unsuitable detergents (like those for

washing up by hand) do not contain the

proper ingredients for use in a dishwasher,

and stop the dishwasher from working

correctly.

The detergent container is inside the door

(fig. A "2"). If the lid of the container is

closed, press the button (A) to open. At the

end of every wash cycle the lid is always

open and ready for the next time the

dishwasher is used.

The amount of detergent to be used varies

according to how dirty the dishes are and

on the type of dishes to be washed. We

advise using 20:30 g of detergent in the

wash section of detergent compartment (B).

After pouring the detergent into the

container, close the lid, firstly pushing (1)

and then pressing on it (2) until you hear

the click.

Since not all detergents are the same the

instructions on the boxes of detergent can

vary. We should just like to remind users

that too little detergent does not clean the

dishes properly whilst too much detergent

will not produce better results and is also a

waste.

Do not use an excessive amount of

detergent and help limit damage to the

environment at the same time.

WARNING

When loading the lower basket, please

ensure that the plates or others

do not

obstruct the detergent dispenser.

Filling the detergent container

It is essential to use a detergent that is

specifically designed for dishwashers

either in powder, liquid,gel or tablet form.

The detergent

8. TYPES OF DETERGENT

Detergent tablets of different manufacturers

dissolve at different speeds, for this reason,

during short programmes, some detergent

tablets may be not fully effective, because

they are not completely dissolved. If these

products are used, is recommended to

choose longer programmes to guarantee

the complete use of the detergent.

The concentrated detergents, with reduced

alkalinity and with natural enzymes, in

conjunction with 50°C wash programmes,

have a smaller impact on the environment

and they protect the dishes and the

dishwasher. The 50°C wash programmes

purposely exploit the dirt-dissolving

properties of the enzymes, allowing

therefore, with the use of the concentrated

detergents, to achieve the same results of

the 65°C programmes but at a lower

temperature.

The detergents that also contain the rinse

aid must be placed in the wash section of

the detergent container. The rinse aid

container must be empty (if it is not empty,

set the rinse aid regulator to lowest position

before using combined detergents).

If you are planning to use "TABS" (“3 in

1 “/ “4 in 1”/ “5 in 1”, etc.) combined

detergents i.e. those with built in salt and/or

rinse agent, we would advise the following:



read carefully and follow the manufacturer’s

instructions given on the packaging;

 the effectiveness of detergents containing

the built in water softener/salt depends on

the hardness of your water supply. Check

that the hardness of your water supply is

within the effective range given on the

detergent packaging.

If when using this type of product, you

don't get satisfactory washing results,

please contact the detergent manufacturer.

In certain circumstances use of combined

detergents can cause:

 limescale deposits on dishes or in the

dishwasher;

 a reduction in washing and drying

performance.

Please note that using the "TABS"

combined detergents, the rinse aid and

salt indicator lights (only used on

selected models) are superfluous, so

you must ignore the lights.

If washing and/or drying problems occur,

we recommend you return to use traditional

separate products (salt, detergent and rinse

agent). This will ensure that the water

softener in the dishwasher operates

correctly.

In this case, we recommends that you:

 refill both the salt and rinse aid container;

 run one normal washing cycle without a

load.

Please note that on return to the use of

conventional salt, a number of cycles will be

required before the system becomes fully

efficient again.

Any problems which arise as a direct

result of the use of these products are not

covered by our warranty.

"TABS" combined detergents

Combined detergents

Concentrated detergents

To get satisfactory washing results,

the tablets MUST be placed in the

wash section of the detergent

container and NOT directly in the tub.

Detergent tablets

LOADING THE RINSE AID

(Fig. A "3")

The rinse aid, which is automatically

released during the last rinsing cycle, helps

the dishes to dry quickly and prevents spots

and stains forming.

The rinse aid container can be found to the

left of the detergent container (fig. A "3").

To open the lid, push the reference mark

and, in the same time, pull the tab of

opening. It is always advisable to use rinse

aid that is specifically designed for

dishwasher. Check the rinse aid level

through the indicator eye (C) which is

located on the dispenser.

FULL EMPTY

dark

light

The regulator (D) is placed under the lid

and can be turned using a coin. The

recommended position is 4.

The limestone content of the water

considerably affects the formation of

limescale and the drying performance.

It is therefore important to regulate the

quantity of rinse aid to achieve good

washing results.

If, after the wash, streaks occur on the

dishes, decrease the amount by one

position. If whitish spots occur, increase the

amount by one position.

Regulating the rinse aid from

1 to 6

Filling the rinse aid container.

The rinse aid

10.

CLEANING THE FILTERS

(Fig. A "4")

The filter system consists of:

A. A central container that traps the larger

particles;

B. A micro filter, located beneath the

gauze, that traps the tiniest particles

ensuring a perfect rinse;

C. A flat gauze that continuously filters the

wash water.

 To achieve excellent results every time,

the filters should be checked and cleaned

after each wash.

 To remove the filter unit, simply turn the

handle anticlockwise (fig. 1).

 For ease of cleaning, the central

container is removable (fig. 2).

 Remove the gauze filter (fig.3) and wash

the whole unit under a jet of water. If

necessary a small brush can be used.

 With the Self-cleaning Micro filter,

maintenance is reduced and the filter unit

need only be checked every two weeks.

Nevertheless, after each wash it is advisable

to check that the central container and the

gauze filter are not clogged.

Never use the dishwasher without the

filters.

WARNING

After cleaning the filters, make

sure that

they are correctly reassembled and

that the gauze filter is properly

positione

d at the bottom of the

dishwasher. Make sure that the filter

is screwed back, clockwise, into the

gauze, as poor seating of the filter unit

could have an adverse effect on the

efficiency of the appliance.

11. PRACTICAL HINTS

 Before placing the dishes in the

dishwasher, remove any remaining food

(bones, shells, pieces of meat or

vegetables, coffee grounds, skin of fruit,

cigarette ash, thooth picks etc. to avoid

blocking the filters, water outlet and

washing arm nozzles.

 Try not to rinse the dishes before loading

them into the dishwasher.

 If saucepans and oven dishes are

encrusted with the remains of burnt or

roast food, it is advisable to leave them to

soak before washing.

 Place the dishes face downwards.

 Try to place the dishes in such a way that

they are not touching one another. If they

are loaded properly you will get better results.

 After loading the dishes check that the

washing arms can rotate freely.

 Pans and other dishes that have

particularly stubborn food particles or

remnants of burnt food should be left to

soak in water with dishwasher detergent.

 To wash silver properly:

a) rinse the silver immediately after use,

especially if it has been used for

mayonnaise, eggs, fish etc.;

b) do not sprinkle detergent onto it;

c) keep it separate from other metals.

Tips on how to save money and not

damage the environment when using your

appliance.

 Achieve the best use of energy, water,

detergent and time by using the

recommended maximum load size. Save

up to 50% energy by washing a full load

instead of 2 half loads.

 If you want the dishwasher to give a

complete wash, place the dishes in the

dishwasher at the end of each meal and if

necessary turn on the COLD RINSE cycle

to soften the food remains and remove

bigger particles of food from the new load

of dishes. When the dishwasher is full

start the complete wash cycle programme.

 If the dishes are not very dirty or if the

baskets are not very full select an

ECONOMY programme, following the

instructions in the program list.

 The most efficient programmes in terms

of combined use of water and energy are

usually the longer-lasting ones with lower

temperature.

 It should be remembered that not all

dishes are suitable for washing in a

dishwasher. We advise against using the

dishwasher to wash items in

thermoplastic, cutlery with wooden or

plastic handles, saucepans with wooden

handles, items in aluminum, crystal

leaded glass unless otherwise stated.

 Certain decorations may fade. It is

therefore a good idea before loading the

whole batch to wash just one of the items

first so as to be sure that others like it will

not fade.

 It is a good idea not to put silver cutlery

with non-stainless steel handles into the

dishwasher as there could be a chemical

reaction between them.

 In order to avoid any dripping from the top

rack, remove the lower rack first.

 If the dishes are to be left in the machine

for some time, leave the door ajar, to let

some air circulate and to improve the

drying performance.

Useful hints

When buying new crockery or cutlery

always make sure that they are

suitable for washing in a dishwasher.

What not to wash.

How to make savings.

How to get really good wash

results.

12. CLEANING AND

MAINTENANCE

Looking after your appliance correctly can

extend its lifespan.

 Disconnect the machine from the power

supply.

 To clean the dishwasher outside, do not

use solvents (degreasing action) neither

abrasives, but only a cloth soaked with

water.

 The dishwasher does not require special

maintenance, because the tank is self-

cleaning.

 Regularly wipe the door gasket with a

damp cloth to remove any food remains

or rinse aid.

 Dishwasher cleaning is recommended, in

order to remove limestone deposits or

dirt. We suggest you run a washing cycle

periodically with specialist dishwasher

cleaning products. For all cleaning

operations the dishwasher must be empty.

 If, in spite of the routine cleaning of the

filters, you notice that the dishes or pans

are not properly washed or rinsed, check

that all the spray heads on the rotor arms

(fig. A “5”) are clear.

If they are blocked, clean them in the

following way:

1) to remove the upper rotor arm, turn it

until it lines up with the stop marked by

the arrow (fig. 1b). Push it upwards

(fig. 1) and, keeping it pushed in,

unscrew it in a clockwise direction (to

reassemble it repeat the same

operation, but turn it anticlockwise).

The lower rotor arm can be removed

simply by pulling it upwards (fig. 2);

2) wash the rotor arms under a jet of water

to clear any blockage in the spray

heads.

3) when you have finished, refit the rotor

arms in the same position,

remembering to re-align the arrow and

screw into position.

 Both the door lining and the tank lining

are in stainless steel; however, should

spots caused by oxidation occur, this is

probably due to a high level of iron salts

presents in the water.

 The spots can be removed with a mild

abrasive agent; never use chlorine based

materials, steel wool, etc.

After every wash it is essential to turn off

water supply and to switch off the machine

by pressing the On/Off button to the off

position.

WHEN CYCLE IS FINISHED.

Do not use tools that can deform the

spray heads.

Cleaning the appliance’s interior

Cleaning the appliance’s exterior

If the machine is not going to be used for

some time, it is advisable to follow these

rules:

1. do an empty wash with detergent in

order to clean the machine of any

deposits;

2. pull out the electric plug;

3. turn off the water tap;

4. fill the rinse aid container;

5. Ieave the door ajar;

6. keep the inside of the machine clean;

7. If the machine is left in places where the

temperature is below 0°C any water left

inside the pipes may freeze. Wait until

the temperature rises above zero and

then wait for about 24 hours before.

13. DESCRIPTION OF THE

CONTROL PANEL

"START/RESET" button

"ADDISH" light

I "OPEN DOOR" light

"EXTRA DRY" light

M "Wi-Fi" light

ON/OFF Button

B "

PROGRAMME SELECTION/

REMOTE CONTROL" button

"DELAY START" button

DISPLAY

"EXTRA DRY" option button

"OPEN DOOR" option button

14. TECHNICAL DATA

TECHNICAL DATA (See rating plate)

9 people

Min. 0,08 – Max. 0,8

See rating plate

9 people

8 people

Place settings (EN 50242)

Capacity with pans and dishes

Water supply pressure (MPa)

Fuse / Power input / Supply voltage

SIZE

BUILT-IN

FULL

INTEGRATED

59,8x81,8 ÷ 89,8x55

117

HALF-

INTEGRATED

59,8x81,8 ÷ 89,8x57

117

FREE-STANDING

WITHOUT WORKTOP

59,8x82x58

117

WITH WORKTOP

60x85x60.9

120

DATA

Width x Height x Depth (cm)

Depth with door open (cm)

15.

PROGRAMME SELECTION

AND SPECIAL FEATURES

 To turn the appliance on and off, press

the

ON/OFF

button (for at least 3 seconds).



Connect the machine to the power supply.

 Open the door, put the dishes to be

washed inside, and close the door again.

 Press the "ON/OFF" button and hold for

about 3 seconds.

 In this phase only the "OPEN DOOR/

EXPRESS" "EXTRA DRY"

and

"START/

RESET"

buttons will remain active. The

message "H-DISH 500" will appear on

the display and all the indicator lights will

turn on for 3 secs.

 The message "ENGLISH" will appear on

the display.

 Pressing the "OPEN DOOR/EXPRESS"

and "EXTRA DRY" buttons you can

select the preferred language.

 To accept the language selection press

the "START/RESET" button Immediately

afterwards the "WELCOME" message

will scroll on the display once and the

indicator lights will all be off.

 "ECO" will appear on the display.

 Press "START/RESET" and a signal will

sound, the indicator light corresponding to

the selected programme will stay on and

the wash indicator light will come on.

 Close the door (after an audible signal

has sounded, the programme will start

automatically).

 Open the door.

 Hold down the ON/OFF button for about 3

secs to turn the machine on and the

ECO" programme or the programme

you have decided to use will appear on

the display, saving it when the dishwasher

switched on. (To save the programme,

see the specific paragraph "Memorising

the last programme used").

The dishwasher is regulated with certain

factory settings. Nevertheless, from the

Settings menu, you can adjust various

parameters to suit your washing requirements.

Entering the Settings menu

 Open the door.

 Turn on the dishwasher by holding the

"ON/OFF" button down for about 3 secs.



Hold down the

"PROGRAMME SELECTION"

and "ON/OFF" buttons for about 5 secs.

 The message "SETTINGS" will appear

on the display and the indicator lights of

the "OPEN DOOR/EXPRESS" and

"EXTRA DRY" buttons will be on.

 Pressing the

"PROGRAMME SELECTION"

button you can select the parameters to

be adjusted in succession (SOFTENER

→ BUZZER → MEMO FUNCTION).

 Parameter adjustment is performed by

pressing the "OPEN DOOR/EXPRESS"

and "EXTRA DRY" buttons.

The dishwasher must ALWAYS be off

before you start this procedure.

Settings Menu

Next time you switch on the

appliance

WARNING

In the event that the machine remains

switched on without selecting or

starting any program, after 5 mins. the

dishwasher will switch off automatically.

First time you switch on the

appliance

At the end of the cycle, remember to

switch off the appliance using the

ON/OFF button, then remove the plug

and close the water supply

ON/OFF button

 To adjust the SOFTENER see the specific

Chapter of the manual).

 To adjust the BUZZER see the specific

paragraph).

 To adjust the MEMO FUNCTION see the

specific paragraph).

 Press the "DELAY START" and "OPEN

DOOR/EXPRESS" buttons together for 3

seconds.

 "ENGLISH" appears on the display.

 Pressing the "OPEN DOOR/EXPRESS"

and "EXTRA DRY" buttons you can

select the preferred language.

 To accept the language selection press

the "START/RESET" button.

Models with Smart Loading Sensor

The "AUTO CARE" programme, thanks to

an algorithm that analyses the degree of

dirtiness of the dishes in real time,

automatically sets the ideal temperature

and washing time , optimising water and

electricity consumption

Models with dirt sensor

(Only on some models).

The dishwasher is equipped with a dirt

sensor, capable of analysing water murkiness

during all "AUTOMATIC" programme

phases (see programme legend). Thanks

to this device, the wash cycle parameters

are automatically adapted to the real

quantity of dirt on dishes. This is because

water murkiness is linked to the quantity of

dirt on dishes. Thus, excellent washing

results are guaranteed while optimising

water and energy consumption.

The "IMPULSE" programmes use an

impulse washing technology, which reduces

consumption and noise, and improves

performance.

When the programme starts, you should

only open the door and add more dishes

when the ADDISH indicator light is switched

on. The appliance will stop automatically and

the time remaining to the

end of the cycle will

flash on the display. Close the door,

without

pressing any buttons

Opening the door when a programme is

running is not recommended especially

during the main wash and final hot rinse

phases. However, if the door is opened

while a programme is running (for example,

to add dishes) the machine stops

automatically. Close the door, without

pressing any buttons. The cycle will start

from where it left off.

Programme interruption

WARNING

If you open the door during the drying

cycle, an intermittent audio signal

advises you that the drying cycle has

not yet finished.

Adding dishes after the ADDISH

indicator light has switched off is

strongly discouraged as this could

affect the wash performance.

Open the door slowly and carefully, to

avoid getting wet with splashes of

washing water

ADDISH (possibility of adding

dishes

after the programme has

started)

The “intermittent” working of the

washing pump is NOT to be

considered a malfunction; it is a

characteristic of impulse washing,

and therefore should be considered a

normal feature of the programme.

"IMPULSE" programmes

(only on some models)

"AUTOMATIC" programmes

(only on some models)

Changing language

Proceed as follows to change or cancel a

running program:

 Open the door.

 Keep the START/RESET button pressed

for at least 3 seconds. "RESET" will

appear on the display and acoustic

signals will be emitted.

 The running programme will be cancelled.

 At this point a new programme can be set

using the

"PROGRAMME SELECTION"

button.

A 5 second buzzer will sound (if not muted)

3 times at 30 second intervals to signal that

the programme has ended.

In some programmes (see table of programmes),

the third washing arm, positioned at the

bottom of the dishwasher POWER WASH,

will also be enabled. This feature is ideal

when cleaning heavily soiled tableware or

cookware, placing them directly in the area

of the basket above the POWER WASH arm.

The option buttons provide you with further

wash options, allowing you to customise the

wash programmes (see the table in chapter

17 for a list of programmes on which each

option can be enabled). Options are

enabled (or disabled) before starting the

programme, using the appropriate buttons.

The relevant indicator lights will appear (or

disappear) on the display.

The option button should be enabled after

you have chosen the wash programme.

"EXPRESS" button

(only on some models).

This button enables average energy and

time savings of 25% (according to the cycle

selected), reducing the wash water

temperature and the drying time during the

final rinse. This option is recommended for

evening washing when perfectly dry dishes

are not needed immediately. For better

drying, leave the dishwasher door slightly

ajar to promote natural air circulation in the

dishwasher.

If an option is selected that is not

compatible with the selected programme

then the option indicator light first flashes

and then goes off.

Option buttons

POWER WASH

(only on some models)

Only for models with the "OPEN DOOR"

option, during the drying phase the

door will open automatically and you

will have to wait until for the end-of-

cycle signal before removing the dishes.

Programme end

WARNING:

Before starting a new programme, you

should check that there is still detergent

in the dispenser. If necessary, top up the

detergent.

Changing a running programme.

WARNING:

If you open the door during the drying

cycle, an intermittent audio sign

advises you that the drying cycle has

not yet finished.

"OPEN DOOR" button "

(AUTOMATIC DOOR OPENING)

(only on some models).

This option enables a special device that

opens the door by a few centimetres during

or at the end of the drying cycle (depending

on the programme). This ensures the natural

and efficient drying of dishes. The duration of

the selected cycle will automatically change to

obtain the optimal temperature for the rinse

cycle; this significantly reduces energy

consumption. The automatic door opening

during the last drying phase enables the air to

circulate, removing the risk of bad odours.

When the door opens, the message "OPEN

DOOR" will appear on the display.

"EXTRA DRY" button

(only on some models).

This option allows you to achieve the

highest efficiency in drying, increasing the

wash water temperature during the last

phase of the wash cycle.

If your dishwasher requires salt, "SALT"

will be displayed when selecting the

programme. The appearance of whitish

stains on dishes is generally a warning sign

that the salt container needs filling.

Dishwasher start time can be set with this

button, delaying start from 1 to 23 hours.

Proceed as follows to set a delayed start:

 Open the door.

 Turn on the dishwasher by pressing the

"ON/OFF" button for about 3 sec.

 Select the washing programme.

 Press the "DELAY START" button

("0:30" will appear on the display).

 Press the button again to increase the

delay (on each press the delay is

increased by 30 mins., up to a maximum

of 23:30.

 When the delay is set on a programme:

- after pressing "START/RESET", the

countdown time “00:00” appears on the

display with flashing “ : ”

- if you press any button (except for the

"ON/OFF"

"PROGRAMME SELECTION"

buttons), the programme name is

displayed for a single scroll on the

display and then the delay time is

displayed again.

When the time has elapsed, the programme

name is displayed for a single scroll on

the display and the remaining time will

be displayed as "0:00h".

To start the countdown, press the

START/RESET button. The display will

show the time remaining to the end of the

programme. At the end of the countdown,

the programme will start automatically.

"DELAY START" button

In order to guarantee the correct

functioning of the

salt indicator light,

YOU MUST ALWAYS FULLY REPLENISH

THE SALT CONTAINER.

"NO SALT" warning light

WARNING

With this option selected, you must

not in any way prevent the door from

opening or force it shut, as this would

damage the mechanism. Ensure that

there is free space in front of the door

and, before closing, wait for the

opening device to complete its activity.

This option is automatically enabled

in the "ECO" pro

gramme. In any case,

it is possible to disable it. The "OPEN

DOOR" feature is not available in the

"RAPID 29’", "RAPID 39’" and "PREWASH"

programmes.

Proceed as follows to cancel a delayed

start:

 Hold the "START/RESET" button down

for at least 3 seconds. "00" will appear on

the display "RESET" and audible signals

will sound.

 The delayed start and the selected

programme will be cancelled. Two

dashes will appear on the display.

 At this point, to set off the dishwasher, a

new programme and any option buttons

must be selected, as indicated in the

"PROGRAMME SETTINGS" paragraph.

You can deactivate turning on and off of the

audio signal as follows (the default setting is

active):

 Open the door.

 Turn on the dishwasher by holding the

"ON/OFF" button down for about 3 secs.



Hold down the

"PROGRAMME SELECTION"

and "ON/OFF" buttons for about 5 secs.

 The message "SETTINGS" will appear

on the display and the indicator lights of

the "OPEN DOOR/EXPRESS" and

"EXTRA DRY" buttons will be on.



Pressing the

"PROGRAMME SELECTION"

button until the "BUZZER" parameter is

selected.

 Parameter adjustment is performed by

pressing the "OPEN DOOR/EXPRESS"

and "EXTRA DRY" buttons to change the

value from YES to NO and vice versa.

 Switch off the dishwasher by pressing the

"ON/OFF" button for 3 secs to confirm

the new setting.

To turn the alarm on again, follow the same

procedure.

 Open the door.

 Turn on the dishwasher by holding the

"ON/OFF" button down for about 3 secs.



Hold down the

"PROGRAMME SELECTION"

and "ON/OFF" buttons for about 5 secs.

 The message "SETTINGS" will appear

on the display and the indicator lights of

the "OPEN DOOR/EXPRESS" and

"EXTRA DRY" buttons will be on.



Pressing the

"PROGRAMME SELECTION"

button until the

"MEMO FUNCTION"

parameter is selected.

 Parameter adjustment is performed by

pressing the "OPEN DOOR/EXPRESS"

and "EXTRA DRY" buttons to change the

value from "MEMO MODE ON" to

"MEMO MODE OFF" and vice versa.

 Switch off the dishwasher by pressing the

"ON/OFF" button for 3 secs to confirm

the new setting.

To turn the alarm on again, follow the same

procedure.

The dishwasher must ALWAYS be off

before you start this procedure.

MEMO FUNCTION (Memorising

the last programme used)

The dishwasher must ALWAYS be off

before you start this procedure.

Activation/Muted END-OF-

PROGRAMME signal.

(Only for free-standing models)

The length of the selected cycle will

be shown on the display. At the end of

the countdown, the programme will

automatically start and the length of

the selected cycle will be shown on

the display.

If the delayed start is not confirmed by

pressing the "START/RESET" button,

after approx. 10 sec. the delayed start

will be cancelled.

Enabling

1. Open the door.

2. Turn on the appliance using the

ON/OFF button.

3. Press the

"PROGRAMME SELECTION"

and "DELAY START" buttons together

for 5 seconds.

4. "DEMO MODE ON" will appear on the

display.

5. If no button is pressed for 30 seconds,

the programme will start, simulating the

start of a wash programme.

Disabling "Demo mode"

1. Open the door.

2. Turn on the appliance using the On/Off

button.

3. Press the

"PROGRAMME SELECTION"

and "DELAY START" buttons together

for 5 seconds.

4. "DEMO MODE OFF" will appear on the

display.

5. Switch off the appliance.

The dishwasher must ALWAYS be off

before you start this procedure.

WARNING

Once installed, if the appliance

works correctly but the wash cycle

does not start upon pressing the

Start button, "Demo mode" may not

have been disabled.

The PROGRAMME SELECTION./

OPTIONS/ DELAY START option

s are

enabled, and by pressing these buttons

you can simulate the product's

functioning without starting a wash.

The dishwasher must ALWAYS be off

before you start this procedure.

Enabling or disabling DEMO MODE

(be used exclusively in stores)

16.

REMOTE CONTROL (WI-FI)

This appliance is equipped with Wi-Fi

technology that allows the machine to be

remote controlled via an app.

 Download the Hoover Wizard app onto

your device.

 Make sure the router is turned on and

your smartphone/tablet is connected to

your home Wi Fi network.

 Turn on BLUETOOTH on your

smartphone/tablet (if available).

 Open the app, create a user profile and

enroll the appliance, following the

instructions appearing on the device’s

display.

 Turn on the dishwasher by pressing the

ON/OFF button for 3 seconds when

instructed to do so in the app.

 Press "PROGRAMME SELECTION

button/ENROLMENT Wi-Fi" for 3 secs

 the message "ENROLMENT" will

scroll on the display and the "Wi-Fi"

indicator light will be off.



Within 60 secs. keep the

"DELAY START"

button pressed for 3 secs., and the

message "EASY" will appear on the

display for 5 mins, the Wi-Fi indicator light

will start to flash slowly 3 times and then

turn off for 2 seconds.

 Enter the password of your home WiFi

network in the App and complete the

procedure.

Successful enrollment

 The message "CONNECTED" will appear

on the display once, after which the message

"REMOTE CONTROL" will appear and

the

"Wi-Fi"

indicator light will be steady on.

 You can now check the machine from the

App.

Unsuccessful enrollment

If enrolment fails (or does not succeed

within 5 mins.):

 "TRY AGAIN" will appear on the display.

 The machine will not be connected.

 Repeat the enrolment procedure from the

App.

For more information, refer to the

“Enrollment App - Quick Guide" that

comes with your machine, also accessible

the link: go.candy-group.com/am-dw

Repeat the enrolment procedure, removing

the product from the APP, in the event of

problems or a change in your home router

password.

Whenever you want to use the machine

with remote control:

 Fill the dishwasher, add detergent.

 Turn on the dishwasher.

 Press "PROGRAMME SELECTION

button/ENROLMENT Wi-Fi" for 3 secs.

 The message "REMOTE CONTROL"

will appear on the display.

 Close the door.

 You can now check the machine from the

App.

ENABLING REMOTE CONTROL

Reset WiFi

To discover all the details of the Wi-Fi

features, explore the app menus in

DEMO mode.

The Hoover Wizard app is available

both for Android and for iOS tablets

and smartphones.

Pairing the machine with the app

 To exit remote control, press

"PROGRAMME SELECTION button/

ENROLMENT Wi-Fi" again for 3 secs.

 When no cycle is under way:

- The Wi-Fi indicator light will start to flash

slowly and the message "REMOTE

CONTROL OFF" will appear on the

display.

 When a cycle is under way:

- The Wi-Fi indicator light will start to flash

slowly and the message "REMOTE

CONTROL OFF" will appear on the

display.

- The message "DOOR OPEN" will appear

on the display.

- The cycle will be completed without

control from the App.

Alternative way to exit remote control.



Press the "START/RESET" button for 3 sec

If there is a cycle under way, it will be

cancelled, and the machine will exit

REMOTE CONTROL mode.

The "Wi-Fi" indicator light will flash

slowly. It is now possible to set a new

wash cycle from the control panel.

 Press the "ON/OFF" button for 3 secs

(or power off)

If there is a cycle under way, it will be

paused and the machine will exit

REMOTE CONTROL mode.

On switching on again, the "Wi-Fi"

indicator light will flash slowly and any

cycle under way will continue from the

point of interruption.

 Indicates the connection status of the

product to the home Wi-Fi network. It can

be:

- SLOW FLASHING: remote control

disabled.

- QUICK FLASHING FOR 3 SECONDS,

THEN OFF: the machine cannot

connect to the home Wi-Fi network or

has not yet been enrolled on the App.

- SLOWLY FLASHING 3 TIMES, THEN

OFF FOR 2 SECONDS: enrolment

procedure on the App in progress.

"Wi-Fi" indicator light

Opening the door, any REMOTE

CONTROL will be disabled. To resume

control from the App, close the door.

DISABLING REMOTE CONTROL

17. PROGRAMME LEGEND

Programme Description

ECO

Programme for normally soiled tableware (the

most efficient in terms of its combined energy and

water consumption for that type of tableware).

Programme standardised to EN 50242.

P2 STEAM

Cycle with alternated action of water jets and

steam. Effective in softening and removing dried

up soil and bacteria, with no need to pre-wash pots

and dishes.

P3 NIGHT

Quietest washing cycle. Ideal for functioning by

night and for taking advantage of reduced energy

fares.

UNIVERSAL Once a day - for normal soiled pans and any other

items that have been left all day for washing.

P5 AUTO CARE

Fast cycle, for “normally” dirty dishes – intended

for frequent washes and normal loads. This

programme is optimised thanks to a smart sensor

that adapts

washing parameters to actual dish

load.

P6 TOTAL CARE

Programme suitable for Class A single-cycle

washing of the most delicate crockery such as

glassware and porcelain.

* Suitable for washing dishes up to 8 place

settings.

P7 RAPID 39' Wash&Dry Class A fast washing cycle. Suitable for

washing dishes up to 8 place.

P8 RAPID 29'

Quick wash for dishes which are to be washed

immediately after the meal. Wash load of 6

persons.

P9 PREWASH Short cold pre-wash for items that are stored in the

dishwasher until you are ready to wash a full load.

Programmes with prewash

For wash programmes with prewash, it is advisable to add a second dose of detergent (max. 10 g)

directly in the machine.

Options

Programme

Detergent for soaking

(Prewash)

"IMPULSE" programmes

Washing temperature

(°C)

Average wash duration ¹ (min.)

"EXPRESS"

button

"OPEN DOOR"

button

"EXTRA DRY"

button

P1 ECO ●

45 232 YES YES YES

STEAM

●

■

75 130 YES YES YES

NIGHT

■ 55 240 YES YES N/A

UNIVERSAL

●

■

60 120 YES YES YES

P5 AUTO CARE

55-65

75-95

YES YES YES

P6 TOTAL CARE

●

■

50 100 YES YES YES

P7 RAPID 39' ●

60 39 YES N/A N/A

P8 RAPID 29'

50 29 N/A N/A N/A

P9 PREWASH

5 N/A N/A N/A

● = Add detergent for prewash

■ = "IMPULSE" Programmes

*= only on some models

N/A= OPTION NOT AVAILABLE

1) With cold water (15°C) – Tollerance ±10%-

With hot water the time remaining until the end of the programme is automatically displayed while

the programme is running.

*Values are measured in a laboratory according to European Standard EN 50242 (consumption

may vary according to conditions of usage).

18.

WATER SOFTENER UNIT

Depending on the source of the supply,

water contains varying amounts of

limestone and minerals which are deposited

on the dishes leaving whitish stains and

marks. The higher the level of these

minerals present in the water, the harder

the water is. The dishwasher is fitted with a

water softener unit which, through the use

of special regenerating salt, supplies

softened water for washing the dishes. The

degree of hardness of your water can be

obtained from your water supply company.

The water softener can treat water with a

hardness level of up to 90 °fH (French grading)

or 50 °dH (German grading) through 8 settings.

The settings are listed in the table below,

with the relative mains water to be treated.

Level

Water hardness

Use of

Regenerating salt

Water softener

setting

°fH

(Franch)

°dH

(German)

0 0-5 0-3 NO S0

1 6-10 4-6 YES S1

2 11-20 7-11 YES S2

3 21-30 12-16 YES S3

4* 31-40 17-22 YES S4

5 41-50 23-27 YES S5

6 51-60 28-33 YES S6

7 61-90 34-50 YES S7

* The softener unit is set in the factory at

level 4 (S4) as this satisfies the requirements

of the majority of users.

Regulate the setting of your water softener

unit according to the degree of hardness of

your water, as follows:

1. Turn on the dishwasher by pressing the

"ON/OFF" button for about 5 secs.

2. Hold the "PROGRAMME SELECTION"

and "ON/OFF" buttons down for about

5 secs.

3. The message "SETUP" will appear on

the display and the indicator lights of

the "OPEN DOOR/EXPRESS" and

"EXTRA DRY" buttons will be on.

Press the

"PROGRAMME SELECTION"

button

until you select

“SOFTENER S4"

(S4 factory level).

5. Parameter adjustment is performed by

pressing the "OPEN DOOR/EXPRESS"

(S7

→

S0)

and "EXTRA DRY" (S0

→

S7)

buttons to increase or decrease the

previously set level.

6. Switch off the dishwasher by pressing

the "ON/OFF" for 3 secs. button to

confirm the new setting.

To change the water softener setting again,

follow the same procedure.

WARNING

If you cannot complete the

procedure,

turn the dishwasher

off by pressing

the

"ON/OFF" button and start the

procedure again from the beginning

(STEP 1).

The dishwasher must ALWAYS be off

before start of this procedure.

Regulating the water softener

19. TROUBLESHOOTING AND WARRANTY

If you believe the dishwasher is not working correctly, consult the quick guide provided

below with some practical tips on how to fix the most common problems. If the

malfunction continues or recurs, contact the Technical Assistance Centre.

Error displayed Meaning and solutions

"CHECK WATER"

with a short audio signal

(only on some models).

E2 (with display) with a

short audio signal

The dishwasher does not fill with water

Make sure the water supply is open.

Make sure the water supply hose is not bent or crushed.

Make sure the drain pipe is at the proper height (see installation

section).

Close the water supply, unscrew the drain pipe from the back of the

dishwasher and check that the "sand" filter is not clogged.

E3 (with display) with a

short audio signal

The dishwasher does not drain water

Make sure the drain pipe isn’t bent, trapped or blocked, and the filter

is not clogged.

Make sure the siphon is not clogged.

E4 (with display) with a

short audio signal

Water leak

Make sure the drain pipe isn’t bent, trapped or blocked, and the filter

is not clogged.

Make sure the siphon is not clogged.

E8-Ei

(with display)

with a short audio signal

The water heating element is not working correctly or the filter

plate is clogged

Clean the filter plate.

Any other code

(with display)

Turn off and unplug the dishwasher, wait a minute. Turn on the

machine and restart a program. If the error occurs again contact an

Authorised Customer Service Centre directly.

Only models with a display

 Models with a display: errors are reported by a number preceded by the letter "E"

(e.g. Error 2 = E2) and a short audio signal.

 Models without a display: an error is shown by a sequence of flashes of every LED.

The error code is shown by the number of flashes followed by a pause of 5 seconds

(example: two flashes – pause 5 seconds – two flashes – repeating = Error 2).

BUG REPORTS

If malfunctions or faults occur when a programme is running, the indicator light that

corresponds to the selected cycle will blink rapidly, and an intermittent audio signal will

sound. In this case, turn the dishwasher off by pressing the "ON/OFF" button.

After checking to make sure the water supply is open, that the drain pipe is not bent

and that the siphon or filters are not clogged, set the selected program again.

If the fault persists, contact the Technical Assistance Centre.

FAULTS

CAUSE

SOLUTION

1. No programme

works

Plug not connected to wall socket

Connect electric plug

O/I button not pressed

Press button

Door is open

Close door

No electricity

Check

2. Dishwasher

does not fill

with water

See point 1

Check

The water tap is closed

Open the water tap

The water supply hose is bent

Eliminate the bends in the hose

The filter of the water supply

hose is clogged

Clean the filter at the end of the

hose

3. Dishwasher

does not

discharge water

Filter is dirty

Clean filter

Drain pipe is bent

Eliminate the bends in the pipe

The drain pipe extension is not

correctly connected

Follow the instructions for connecting

the drain pipe carefully

The outlet connection on the

wall is pointing downwards not

upwards

Call a qualified technician

4. Dishwasher

discharges

water

continuously

Position of the drain pipe is too

low

Lift drain pipe to at least 40 cm

above floor level

Other faults

WARNING

To ensure the correct operation of the overflow safety

device, we recommend not moving or tilting the dishwasher

during operation.

Should it be necessary to tilt or move the

dishwasher, please ensure that the washing cycle is

complete and that no water remains inside the appliance.

This dishwasher is equipped with an overflow safety device that, in the event of a

problem, automatically discharges any excess water.

Only models without a display

FAULTS

CAUSE

SOLUTION

5. Spray arms are

not heard to

rotate

Excessive amount of detergent

Reduce amount of detergent Use

suitable detergent

Item prevents arms from rotating

Check

Filtering plate and filter very dirty

Clean filtering plate and filter

6. On electronic

appliances

without a

display: one or

more indicator

lights flashing

quickly

Water supply tap turned off Switch off the appliance. Turn on

the tap. Re-set the cycle.

7. Dishes only

partially washed

See point 5

Check

Bottom of saucepans have not

been washed well

Burnt on food remains must be

soaked before putting pans in

dishwasher

Edge of saucepans have not

been washed well

Reposition saucepans

Spray arms are partially blocked

Remove spray arms by unscrewing

ring nuts clockwise and wash under

running water

The dishes have not been

loaded properly

Do not place the dishes too close

together

The end of the drain pipe is

immersed in water

The end of the drain pipe must not

come into contact with the outflow

water

An incorrect amount of

detergent has been measured

out, or the detergent is old and

hard

Increase the measure according to

how dirty the dishes are, or change

detergent

The cap of the salt container is

not closed properly

Choose a more vigorous

programme

The wash programme is not

thorough enough

Tighten it properly

8. Detergent not

dispensed or

partially

dispensed

Cutlery, dishes, pans, etc., stop

the detergent dispenser from

opening

Position dishes so as not to

obstruct the dispenser

9. Presence of

white spots on

dishes

Mains water is too hard

Check salt and rinse aid level and

regulate. Should the fault persist,

contact the Technical Assistance

Centre

10. Noise during

wash

The dishes knock against one

another

Re-check loading of dishes in the

basket

The revolving arms knock

against the dishes

Re-check loading of dishes in the

basket

11. The dishes

are not

completely dry

Inadequate air flow

Leave the dishwasher door ajar at

the end of the wash program to

allow the dishes to dry naturally

Rinse aid missing

Fill the rinse aid dispenser

N.B.: Should any of the above situations result in a bad wash performance or insufficient

rinsing, remove dirt deposits from the dishes by hand since the final drying cycle hardens

the dirt, making it difficult to remove with a subsequent wash.

If the malfunction continues, contact the Technical Assistance Centre, quoting the model of

the dishwasher. This is found on the plate on the upper section of the inside of the

dishwasher door, or on the warranty. This information will make it possible to take quicker,

more effective action.

It is always recommended to use original spare parts, that are available at our Authorised

Customer Service Centres.

The manufacturer declines all responsibility for any printing errors in this booklet.

Moreover, the manufacturer reserves the right to make any changes deemed useful to its

products without changing their essential characteristics.

Assistance and Warranty

The product is guaranteed under the law, and under the terms and conditions

stated on the warranty certificate included with the product. The certificate

should be stored and shown to an authorized Technical Assistance Centre in

case of need, together with

the proof of purchase. You can also check the

warranty conditions on our website.

For assistance, please fill in the online form or contact us at the number

indicated on the support page of our website.

20. ENVIRONMENTAL CONDITIONS

This appliance is marked a

cording to the European directive

2012/19/EUon Waste Electrical

and Electronic Equipment

(WEEE).

WEEE contains both polluting substances

(which can cause negative consequences

for the environment) and basic components

(which can

be re-used).

It is important to have WEEE subjected to

specific treatments, in order to remove

and dispose properly all pollutants,

and recover and recycle all materials.

Individuals can play an important role in

ensuring that WEEE does not become an

environmental issue; it is



WEEE should not be treated as

household waste;



WEEE should be handed over to the

relevant collection points managed by

the municipality or by re

gistered

companies. In many countries, for large

WEEE, home collection could be

present.

In many countries, when you buy a new

appliance, the old one may be returned to

the retailer who has to collect it free of

charge on a one

-to-

one basis, as long as

the equipment is of equivalent type and

has the same functions as the supplied

equipment.

- HDIN 4D620P -

22.02 - 70011097 - IDM s.r.l.

Table of Contents

Hoover HDIN 4D620PB-80E User Manual

Related Manuals