Table of Contents
Hoover HOC3UB3158BI WF User Manual
Displayed below is the user manual for HOC3UB3158BI WF by Hoover which is a product in the Ovens category. This manual has pages.
Related Manuals
USER INSTRUCTIONS
OVENS EN 02
CANDY HOOVER GROUP S.R.L. • Via Comolli 16 • 20861 Brugherio (MB) - Italy
General Warnings
• When you open the door after you have finished
cooking, a few drops of water may come out of the
door. It depends on the type of food you have
cooked.
• During cooking, moisture may condense inside
the oven cavity or on the glass of the door. This is a
normal condition. To reduce this effect, wait 10-
15 minutes after turning on the power before
putting food inside the oven. ln any case, the
condensation disappears when the oven reaches
the cooking temperature.
• Cook the vegetables in a container with a lid
instead of an open tray.
• Avoid leaving food inside the oven after cooking
for more than 15/20 minutes.
• WARNING: the appliance and accessible parts
become hot during use. Be careful not to touch
any hot parts.
• WARNING: the accessible parts can become hot
when the grill is in use. Children should be kept at
a safe distance.
• WARNING: ensure that the appliance is
switched off before replacing the bulb, to avoid
the possibility of electric shocks.
• WARNING: in order to avoid any danger caused
by the accidental resetting of the thermal
interruption device, the appliance should not be
powered by an external switching device, such as
a timer, or be connected to a circuit that is
regularly switched on and off.
• Children under 8 should be kept at a safe
distance from the appliance if not continuously
supervised.
• Children should not play with the appliance.
• The appliance can be used by those aged 8 or
over and by those with limited physical, sensorial
or mental capacities, without experience or
knowledge of the product, only if supervised or
provided with instruction as to the operation of
the appliance, in a safe way with awareness of the
possible risks.
• Cleaning and maintenance should not be carried
out by unsupervised children.
• Do not use rough or abrasive materials or sharp
metal scrapers to clean the oven door glasses, as
they can scratch the surface and cause the glass to
shatter.
• The oven must be switched off before removing
the removable parts. After cleaning, reassemble
them according the instructions.
• Only use the meat probe recommended for this
oven.
• Do not use a steam cleaner for cleaning
operations.
• Connect a plug to the supply cable that is able to
bear the voltage, current and load indicated on
the tag and having the earth contact. The socket
must be suitable for the load indicated on the tag
and must have ground contact connected and in
operation. The earth conductor is yellow-green in
colour. This operation should be carried out by a
suitably qualified professional. ln case of
incompatibility between the socket and the
appliance plug, ask a qualified electrician to
substitute the socket with another suitable type.
The plug and the socket must be conformed to the
current norms of the installation country.
Connection to the power source can also be made
by placing an omnipolar breaker between the
appliance and the power source that can bear the
maximum connected load and that is in line with
current legislation. The yellow-green earth cable
should not be interrupted by the breaker. The
socket or omnipolar breaker used for the
connection should be easily accessible when the
appliance is installed.
• The disconnection may be achieved by having
the plug accessible or by incorporating a switch in
the fixed wiring in accordance with the wiring
rules.
• lf the power cable is damaged, it should be
substituted with a cable or special bundle
available from the manufacturer or by contacting
the customer service department. The type of
power cable must be H05V2V2-F. This operation
should be carried out by a suitably qualified
professional. The earth conductor (yellow-green)
must be approximately 10 mm longer than the
other conductors. For any repairs, refer only to
the Customer Care Department and request the
use of original spare parts.
• Failure to comply with the above can
EN 02
compromise the safety of the appliance and
invalidate the guarantee.
• Any excess of spilled material should be
removed before cleaning.
• A long power supply failure during an occurring
cooking phase may cause a malfunction of the
monitor. ln this case contact customer service.
• The appliance must not be installed behind a
decorative door in order to avoid overheating.
• When you place the shelf inside, make sure that
the stop is directed upwards and in the back of the
cavity. The shelf must be inserted completely into
the cavity.
• WARNING: Do not line the oven walls with
aluminium foil or single-use protection available
from stores. Aluminium foil or any other
protection, in direct contact with the hot enamel,
risk melting and deteriorating the enamel of the
insides.
• WARNING: Never remove the oven door seal.
• CAUTION: Do not refill the cavity bottom with
water during cooking or when the oven is hot.
• No additional operation/setting is required in
order to operate the appliance at the rated
frequencies.
EN 03
General Instructions
5
1.1 Safety indications
1.2 Electrical safety
1.3 Recommendations
1.4 Installation
1.5 Waste management
1.6 Declaration of compliance
2.1 Overview
2.2 Accessories
2.3 First use
Product Description
6
3.1 Display description
3.2 Cooking modes
Use of the Oven
7
4.1 General notes on cleaning
4.2 Hydro Easy Clean Function
4.3 Maintenance
• Instructıon for removal and cleanıng of the
sıde racks
• Removal of the oven window
• Removal and cleaning of the glass door
• Changing the bulb
Oven Cleaning and Maintenance
11
5.1 F.A.Q.
Troubleshooting
13
Summary
EN 04
1. General Instructions
We thank you for choosing one of our products. For the best results with your oven, you should read
this manual carefully and retain it for future reference. Before installing the oven, take note of the serial
number so that you can give it to customer service staff if any repairs are required. Having removed the
oven from its packaging, check that it has not been damaged during transportation. If you have doubts,
do not use the oven and refer to a qualified technician for advice. Keep all of the packaging material
(plastic bags, polystyrene, nails) out of the reach of children. When the oven is switched on for the first
time, strong smelling smoke can develop, which is caused by the glue on the insulation panels
surrounding the oven heating for the first time. This is absolutely normal and, if it occurs, you should
wait for the smoke to dissipate before putting food in the oven. The manufacturer accepts no
responsibility in cases where the instructions contained in this document are not observed.
NOTE: the oven functions, properties and accessories cited in this manual will vary, depending on the
model you have purchased.
1.1 Safety Indications
Only use the oven for its intended purpose, that is only for the cooking of
foods; any other use, for example as a heat source, is considered improper
and therefore dangerous. The manufacturer cannot be held responsible for
any damage resulting from improper, incorrect or unreasonable usage.
The use of any electrical appliance implies the observance of some
fundamental rules:
- do not pull on the power cable to disconnect the plug from the socket;
- do not touch the appliance with wet or damp hands or feet;
- in general the use of adaptors, multiple sockets and extension cables is not
recommended;
- in case of malfunction and/or poor operation, switch off the appliance and
do not tamper with it.
1.2 Electrical Safety
ENSURE THAT AN ELECTRICIAN OR QUALIFIED TECHNICIAN MAKES THE
ELECTRICAL CONNECTIONS. The power supply to which the oven is
connected must conform with the laws in force in the country of
installation. The manufacturer accepts no responsibility for any damage
caused by the failure to observe these instructions. The oven must be
connected to an electrical supply with an earthed wall outlet or a
disconnector with multiple poles, depending on the laws in force in the
country of installation. The electrical supply should be protected with
suitable fuses and the cables used must have a transverse section that can
ensure correct supply to the oven.
CONNECTION
The oven is supplied with a power cable that should only be connected to
an electrical supply with 220-240 Vac 50 Hz power between the phases or
between the phase and neutral. Before the oven is connected to the
electrical supply, it is important to check:
- power voltage indicated on the gauge;
- the setting of the disconnector.
The grounding wire connected to the oven's earth terminal must be
connected to the earth terminal of the power supply.
WARNING
Before connecting the oven to the power supply, ask a qualified electrician
to check the continuity of the power supply's earth terminal. The
manufacturer accepts no responsibility for any accidents or other
problems caused by failure to connect the oven to the earth terminal or by
an earth connection that has defective continuity.
NOTE: as the oven could require maintenance work, it is advisable to keep
another wall socket available so that the oven can be connected to this if it
is removed from the space in which it is installed. The power cable must
only be substituted by technical service staff or by technicians with
equivalent qualifications.
1.3 Recommendations
After each use of the oven, a minimum of cleaning will help keep the oven
perfectly clean.
Do not line the oven walls with aluminium foil or single-use protection
available from stores. Aluminium foil or any other protection, in direct contact
with the hot enamel, risks melting and deteriorating the enamel of the insides.
In order to prevent excessive dirtying of your oven and the resulting strong
smokey smells, we recommend not using the oven at very high temperature. It
is better to extend the cooking time and lower the temperature a little. In
addition to the accessories supplied with the oven, we advise you only use
dishes and baking moulds resistant to very high temperatures.
1.4 Installation
The manufacturers have no obligation to carry this out. If the assistance of the
manufacturer is required to rectify faults arising from incorrect installation,
this assistance is not covered by the guarantee. The installation instructions
for professionally qualified personnel must be followed. Incorrect installation
may cause harm or injury to people, animals or belongings. The manufacturer
cannot be held responsible for such harm or injury.
The oven can be located high in a column or under a worktop. Before fixing,
you must ensure good ventilation in the oven space to allow proper
circulation of the fresh air required for cooling and protecting the internal
parts. Make the openings specified on last page according to the type of
fitting.
1.5 Waste management and environmental protection
This appliance is labelled in accordance with European Directive
2012/19/EU regarding electric and electronic appliances (WEEE). The
WEEE contain both polluting substances (that can have a negative effect on
the environment) and base elements (that can be reused). It is
important that the WEEE undergo specific treatments to
correctly remove and dispose of the pollutants and recover all
the materials. Individuals can play an important role in
ensuring that the WEEE do not become an environmental
problem; it is essential to follow a few basic rules:
- the WEEE should not be treated as domestic waste;
- the WEEE should be taken to dedicated collection areas managed by the
town council or a registered company.
In many countries, domestic collections may be available for large WEEEs.
When you buy a new appliance, the old one can be returned to the vendor
who must accept it free of charge as a one-off, as long as the appliance is of
an equivalent type and has the same functions as the purchased appliance.
SAVING AND RESPECTING THE ENVIRONMENT
Where possible, avoid pre-heating the oven and always try to fill it. Open
the oven door as infrequently as possible, because heat from the cavity
disperses every time it is opened. For a significant energy saving, switch off
the oven between 5 and 10 minutes before the planned end of the cooking
time, and use the residual heat that the oven continues to generate. Keep
the seals clean and in order, to avoid any heat dispersal outside of the
cavity. If you have an electric contract with an hourly tariff, the "delayed
cooking" programme makes energy saving more simple, moving the
cooking process to start at the reduced tariff time slot.
EN 05
2. Product Description
2.1 Overview
1. Control panel
2. Shelf positions
(lateral wire grid if included)
3. Metal grill
4. Drip pan
5. Fan (behind the steel plate)
6. Oven door
2.2 Accessories (According to model)
Drip pan
1
Collects the residues that drip during the cooking of foods on the grills.
Lateral wire grids
3
It located at both sides of the oven cavity. It holds metal grills and drip pans.
Metal grill
2
Holds baking trays and plates.
4Grill pan set
The simple shelf can take moulds and dishes.
The tray holder shelf is especially good for grilling things. Use it with the drip
tray.
The special profile of the shelves means they stay horizontal even when
pulled right out. There is no risk of a dish sliding or spilling.
The drip tray catches the juices from grilled foods. It is only used with the
Grill, Rotisserie, or Fan Assisted Grill ; remove it from the oven for other
cooking methods.
Never use the drip tray as a roasting tray as this creates smoke and fat will
spatter your oven making it dirty.
The tray holder
The tray holder shelf is ideal for grilling. Use it in conjunction with the drip
tray. A handle is included to assist in moving the both accessories safely. Do
no leave the handle inside the oven.
1.6 Declaration of compliance
By placing the mark on the appliance, we are confirming compliance
to all relevant European safety, health and environmental requirements
which are applicable in legislation for this product.
2.3 First Use
PRELIMINARY CLEANING
Clean the oven before using for the first time. Wipe over external surfaces with a damp soft cloth. Wash all accessories and wipe inside the oven with a
solution of hot water and washing up liquid. Set the empty oven to the maximum temperature and leave on for about 1 hour, this will remove any lingering
smells of newness.
EN 06
Hereby, Candy Hoover Group Srl declares that the radio equipment is in
compliance with Directive 2014/53/EU. The full text of the EU declaration
of conformity is available at the following internet address: www.candy-
group.com.
2
3
5
4
6
1
5
6
29
7
8
3
4
3. Use of the Oven (According to model)
3.1 Display description
EN 07
WARNING : the first operation to carry out after the oven has been installed or following the interruption
of power supply (this is recognizable the display pulsating and showing ) is setting the correct time. 12:00
The bottom right LED flashes at the same time ( ). This is achieved as follows.
•Set time with buttons."-" "+"
•Push the Menu button or wait 5 seconds than the clock is setted.
ATTENTION: The oven will only operate setting the clock
1. Thermostat selector knob
2. Thermostat signal lamp
3. End of cooking
4. Cooking time
5. Temperature or clock display
6. LCD display adjustment controls
7. Minute minder
8. Clock setting
9. Wifi signal lamp
10. Function selector knob
FUNCTION HOW TO DEACTIVATE WHAT IT DOES NOTE
HOW TO USE
KEY LOCK
•Child Lock function is activated by
touching Set (+) for a minimum of 5
seconds. From this moment on all
other function are locked and the
display will flash 3 sec intervals STOP
and preset time intermittently.
•Child Lock function is deactivated
by touching touchpad Set (+) again
for a minimum of seconds. From 5
this moment on all functions are
selectable again.
•Push the central button 3 times
•Press the buttons "-" "+" to set
the required time
•Release all the buttons
•When the set time has elapsed, an
audible alarm is full stop after
activated this alarm will stop on its
own, however it can be stopped
immediately by pressing any button.
•Sounds an alarm at the end of the
set time.
•During the process, the display
shows the remaining time.
•Allows to use the oven as alarm clock
(could be activated either with operating
the oven or with out operating the oven)
•Select the cooking function with the
oven function knob, the temperature
you want to cook with the
thermostat knob.
• Push the central button 1 times
• Press the buttons "-" or "+"to set
the lenght of cooking required
• Release all buttons
NOTE: If the oven is switched off or
the lamp is functioning, the cooking
time schedule function will not work.
• It allows to preset the cooking time
required for the recipe chosen.
• To check how long is left to run
press the MENU button 1 time.
• To alter/change the preset time
press MENU and "-" "+" buttons.
•Push any button to stop the
signal. Push the central button to
return to the clock function.
•At the end of the program the program
gives 3 warning signals and “End” appears
on the display.
Set the function selector switch to "0" to
return to the clock function.
•At the time set, the oven will
switch off. To switch off manually,
turn the oven function selector to
position O.
•Enables you to set the end of
cooking time
•To check the preset time push the
central button 2 times
•To modify the preset time press
buttons MENU + "-" "+"
•Select the cooking function with
the oven function knob, the
temperature you want to cook with
the thermostat knob.
•Push the central button times 2
•Press the buttons "-" "+" to set the
time at which you wish the oven to
switch off
•Release the buttons
NOTE: If the oven is switched off or
the lamp is functioning, the cooking
time schedule function will not
work.
•This function is typically used with
“cooking time” function.
For example if the dish has to be cooked
for 45 minutes and needs to be ready by
12:30, simply select the required
function, set the cooking time to 45
minutes and the end of cooking time to
12:30.
•At the end of the cooking set time, the
oven will switch off automatically and an
audible alarm will ring.
•Cooking will start automatically at 11:45
(12:30 minus 45 mins) and will continue
until the pre-set end-of-cooking-time,
when the oven will switch itself off
automatically.
END OF
COOKING
COOKING
TIME
MINUTE
MINDER
110
1. Program selection / 2. Program duration / 3. Cooking start setting / 4- Dedicated recipes selection / 5. Offline and vocal assistant /
6. Tips, suggestions and online user manual
1 2
3 4
6
5
ELETTRONICA ZERO WIFI FUNCTION
For all the details related to the link between app and product, refer to the Quick Guide.
The Quick Guide is available on: go.candy-group.com/candy-ov
Wi Fi has two different positions on the cooking selector:
• Wi Fi on: Wi Fi is switched on only if the oven is already enrolled to your device. In this position the oven will be only controlled by
remote.
• Wi Fi reset: After leaving the selector on Wi Fi reset for 30”, Bluetooth will switch on and you will be able to enroll the oven to your
device within 5’.
If the enrollment is successful, the oven will be controlled by remote and the Wi Fi icon will switch on. If the enrollment is unsuccessful,
Wi Fi will switch off and the oven will be reset.
To proceed with a new enrollment the cooking program selector has to be turned out from Wi Fi reset position and moved again on it.
Note: Install the App on your device before starting enrolling
Note: The device where the App is installed must have Bluetooth activated
Note: For both Wi Fi positions, the touch buttons do not work.
Note: It is important to establish a good Wi-Fi signal strength between the home router and the appliance. When the oven is trying to
connect to router the icon will blink 3” on and 1” off, when it is already connected the icon will switch on.
EN 08
WIRELESS PARAMETERS
Bluetooth v4.2
2,412 GHz. – 2,484 GHz
Basic data rate:
RF Transmit Power (Typ):
+4 dBm
Enhanced data rate:
RF Transmit Power (Typ):
+2 dBm
BLE:
RF Transmit Power (Typ):
+7.5 dBm
802.11 b/g/n
2,412 GHz. – 2,484 GHz
802.11b. DSSS 1 Mbps=
+19.5 dBm
802.11b. CCK 11 Mbps=
+18.5 dBm
802.11g. OFDM 54 Mbps=
+18.5 dBm
802.11n. MCS7=
+14 dBm
802.11b =1024 bytes,
-80 dBm
802.11g =1024 bytes,
-70 dBm
802.11n =1024 bytes,
-65 dBm
802.11n HT40 =1024 bytes,
-65 dBm
Wireless Standart
Frequency Range
Max Transmit Power
Minimum Receiving
Sensivity
Parameter Specifications
(Wi-Fi)
Specifications
(Bluetooth)
Basic data rate:
Sensivity@ 0.1% BER:
-98 dBm
Enhanced data rate:
Sensivity@ 001% BER:
-98 dBm
BLE:
Sensivity@ 0.1% BER:
-98 dBm
Product information for networked equipment
power consumption of the product in
networked standby if all wired network
ports are connected and all wireless
network ports are activated:
2,0 W
How to activate wireless network port:
Starting from an oven that is not enrolled,
putting the right knob on the Reset position.
Wifi module is switched on after 30".
If oven is enrolled with WiFi off, putting the
right knob on WiFi position the WiFi module
is switched on.
How to deactivate wireless network port: If oven is enrolled, putting the right knob on
Reset position the WiFi module is switched
off.
HOOVER
For detailed information about HOW TO CONNECT your ONEFi appliance and HOW TO USE it at its best,
go to http://wizardservice.candy-hoover.com/
Quick Guide Hoover OVEN - Enrollment on App
Procedure for devices with Bluetooth 4.0 (or higher)
IMPORTANT
This quick guide illustrates the steps to follow to enroll your appliance on
the App Hoover Wizard, using a device with Bluetooth 4.0 (or higher)
technology. In this case, the procedure is simplified and faster (Easy
Enrollment). If you are using a device without Bluetooth technology (or less
than 4.0), please follow the instructions described on the other side of this
guide.
STEP 1
• Mark down the appliance Serial Number.
• Mark down the Wi-Fi Name and Password (WPA/WEP Key) which are
normally placed on the back of your Wi-Fi router.NOTES
• The frequency of the home Wi-Fi network has to be set on the 2.4 GHz
band. You cannot configure the appliance if your home network is set to the
5 GHz band.
• If you are having trouble locating the WPA/WEP Password, please contact
your Internet Provider.
• Please make sure your smartphone is connected to the same Wi-Fi
network and has the Bluetooth enabled within the “Settings”. Refer to the
manual for more details.
STEP 2
• Download the Hoover Wizard App from the Store.
• Open the Hoover Wizard App and create your user profile by taping on
“Register”. Accept the privacy policy and fill in the required fields.
NOTES
• The App is available for Android (version 4.4 or higher) and iOS (version
8.0 or higher) devices.
• If you already have a Hoover Wizard user profile, you can login using your
credentials.
STEP 3
• In the homepage, tap on the icon with the three bars on the top left to
enter your profile, then tap on “REGISTER NEW APPLIANCE” and select the
name of the product that you want to enroll.
STEP 4
• Insert the purchase date of your appliance (DD/MM/YYYY), then tap on
“Proceed”.
STEP 5
• Insert the 16 digits of the serial number or scan the QR code on the
appliance. Tap on “Next”. Check data correctness of the data and tap on
“Confirm”. Once the system has recognized the product, tap on “Next”.
STEP 6
On the appliance:
1) Turn the knob to the WI-FI RESET program and wait 30 seconds.
2) When the Wi-Fi indicator starts blinking quickly, Bluetooth will come on
for 5' and you can proceed with enrollment within 5 minutes.
In App:
• Tap on “Confirm”. Wait for APP to connect to the appliance.
NOTES
• In case of any issue, tap “Retry”, making sure you have enabled Bluetooth
on your device (smartphone / tablet). If the process has not been
completed correctly yet, tap on “Proceed with Standard Enrollment”.
• To ensure correct data transfer, we recommend you to stay with the
device close to the appliance.
STEP 7
• Insert the password of your home Wi-Fi network.
• Select the type of password (WEP or WPA), then tap on “Confirm”.
• The enrollment process is now finished.
NOTES
• If this is not automatically synchronised by the App, please insert the
name of your home Wi-Fi network in the first box; pay attention to the
difference between lowercase and uppercase.
IF THE SET UP IS NOT SUCCESSFUL
It's important to establish a good Wi-Fi signal strength between the home
router and the appliance: low Wi-Fi signal strength would cause the failure
of the final stage of the set up. To assess if this is the case, start the
connection process again from Step 1; when you get to Step 6, when you
get to Step 6, place your device (smartphone or tablet) next to the router
and search for “WIFIOVEN-xyzk” net generated by the appliance. If this
does not come up as an option, it means that the router cannot see the
appliance. In this case, we highly recommend you to bring the router near
the appliance (if possible) or contact your internet provider to purchase a
compatible “Wi-Fi Range Extender” to increase the signal strenght.
Remote control mode
• Turn the program selection knob to the WI-FI position: the wifi light will
turn on and you can now control the oven remotely.
NOTES
• Warning, if the enrolled oven is left on the WI-FI RESET position for more
than 5 minutes, the oven will be reset and you will have to proceed with a
new enrollment.
Quick Guide Hoover OVEN - Enrollment on App
Procedure for devices without Bluetooth 4.0 (or less than 4.0)
IMPORTANT
This quick guide outlines the steps you should follow to enroll your
appliance using the App Hoover Wizard, utilizing a device without
Bluetooth technology. We recommend you to proceed with a
smartphone/tablet equipped with this technology to make the procedure
simpler.
If you are using a device with Bluetooth technology (or higher than 4.0),
please follow the instructions described on the other side of this guide.
STEP 1
• Make a note of the appliance Serial Number and Wi-Fi Name and
Password (WPA/WEP Key), which are normally found on the back of your
Wi-Fi router.
• Please make sure that your smartphone/ tablet is connected to the same
Wi-Fi network.
NOTES
• The frequency of the home Wi-Fi network has to be set on the 2.4 GHz
band. You can not configure the appliance if your home network is set to
the 5 GHz band.
• If you are having trouble locating the WPA/WEP Password, please contact
your Internet Provider.
STEP 2
• Download the Hoover Wizard App from the Store.
• Open the Hoover Wizard App and create your user profile by taping on
“Register”. Accept the privacy policy and fill in the required fields.
NOTES
• The App is available for Android (version 4.4 or higher) and iOS (version
8.0 or higher) devices.
• If you already have a Hoover Wizard user profile, you can login using your
credentials.
STEP 3
• In the homepage, tap on the icon with the three bars on the top left to
enter your profile, then tap on “REGISTER NEW APPLIANCE” and select the
name of the product that you want to enroll.
STEP 4
• Insert the purchase date of your appliance (DD/MM/YYYY), then tap on
“Proceed”.
STEP 5
• Insert the 16 digits of the serial number or scan the QR code on the
appliance. Tap on “Next”. Check data correctness and tap on “Confirm”.
Once the system has recognized the product, tap on “Next”.
STEP 6
• On the appliance - Turn the knob to the WI-FI RESET program and wait 5
minutes. The countdown will appear on the App, after which you can
complete enrollment.
• In App- Tap on “Confirm”.
NOTES
• To ensure correct data transfer, we recommend that you stay with the
device close to the appliance.
STEP 7
• Exit the Hoover Wizard App.
• Go to your device Wi-Fi settings.
STEP 8
• In the list of available Wi-Fi networks, select “WIFIOVEN-xyzk”.
NOTES
• If you do not find it, wait few more seconds or proceed with a new scan.
STEP 9
• Exit from the settings of your device.
• Return to the Hoover Wizard App and wait for the App to detect the
appliance.
• Once the “Wi-Fi Network is active” screen appears, tap on “Next”.
STEP 10
• Insert the password of your home Wi-Fi network.
• Select the type of password (WEP or WPA), then tap on “Confirm”.
NOTES
• If this is not automatically synchronised by the App, please insert the
name of your home Wi-Fi network in the first box; pay attention to the
difference between lowercase and uppercase.
STEP 11
• Wait until the end of the data transfer process between the App and the
product, then tap on “Confirm”. “CONNECTED” appears on the appliance
display and then “REMOTE CONTROL ON”.
• The enrollment process is now finished.
IF THE SET UP IS NOT SUCCESSFUL
It's important to establish a good Wi-Fi signal strength between the home
router and the appliance: low Wi-Fi signal strength would cause the failure
of the final stage of the set up. To assess if this is the case, start the
connection process again from Step 1; when you get to Step 6, place your
device (smartphone or tablet) next to the router and search for
“WIFIOVEN-xyzk” net generated by the appliance. If this does not come up
as an option, it means that the router cannot see the appliance. In this case,
we highly recommend you to bring the router near the appliance (if
possible) or contact your internet provider to purchase a compatible “Wi-Fi
Range Extender” to increase the signal strenght.
Remote control mode
• Turn the program selection knob to the WI-FI position: the wifi light will
turn on and you can now control the oven remotely.
NOTES
• Warning, if the enrolled oven is left on the WI-FI RESET position for more
than 5 minutes, the oven will be reset and you will have to proceed with a
new enrollment.
EN 09
T °C
Suggested
180
210
230
Function
Dial Function (Depends on the oven model)
LAMP: Turns on the oven light.
220
220
190
3.2 Cooking Modes
*
GRILL: use the grill with the door closed.
The top heating element is used alone and you can adjust the temperature. Five minutes preheating is required to get the
elements red-hot. Success is guaranteed for grills, kebabs and gratin dishes. White meats should be put at a distance from the
grill; the cooking time is longer, but the meat will be tastier. You can put red meats and fish fillets on the shelf with the drip tray
underneath. The oven has two grill positions: Grill: 2140 W Barbecue: 3340 W
MULTI-LEVEL: We recommend you use this method for poultry, pastries, fish and vegetables. Heat penetrates into the food
better and both the cooking and preheating times are reduced. You can cook different foods at the same time with or without
the same preparation in one or more positions. This cooking method gives even heat distribution and the smells are not
mixed.
Allow about ten minutes extra when cooking foods at the same time.
DEFROST: When the dial is set to this position. The fan circulates air at room temperature around the frozen food so that it
defrosts in a few minutes without the protein content of the food being changed or altered.
BOTTOM HEATING + FAN: The bottom heating element is used with the fan circulating the air inside the oven. This method is
ideal for juicy fruit flans, tarts, quiches and pâté.
It prevents food from drying and encourages rising in cakes, bread dough and other bottom-cooked food.
Place the shelf in the bottom position.
CONVENTIONAL: Both top and bottom heating elements are used. Preheat the oven for about ten minutes. This method is
ideal for all traditional roasting and baking. For seizing red meats, roast beef, leg of lamb, game, bread, foil wrapped food
(papillotes), flaky pastry. Place the food and its dish on a shelf in mid position.
PIZZA: With this function hot air circulated in the oven to ensure perfect result for dishes such as pizza or cake.
WIFI ON: Oven allows wifi connection.
WIFI RESET: It allows wifi connection to be restarted.
MASTER BAKE : This function allows to cook in a healthier way, by reducing the amount of fat or oil required. The
combination of heating elements with a pulsating cycle of air ensures a perfect baking result.
*
*Tested in accordance with the EN 60350-1 for the purpose of energy consumption declaration and energy class.
EN 10
T °C
Range
50 ÷ MAX
50 ÷ MAX
50 ÷ MAX
50 ÷ MAX
50 ÷ MAX
50 ÷ MAX
4. Oven cleaning and maintenance
4.1 General notes on cleaning
The lifecycle of the appliance can be extended through regular cleaning.
Wait for the oven to cool before carrying out manual cleaning operations.
Never use abrasive detergents, steel wool or sharp objects for cleaning, so
as to not irreparably damage the enamelled parts. Use only water, soap or
bleach-based detergents (ammonia).
GLASS PARTS
It is advisable to clean the glass window with absorbent kitchen towel after
every use of the oven. To remove more obstinate stains, you can use a
detergent-soaked sponge, well wrung out, and then rinse with water.
OVEN WINDOW SEAL
If dirty, the seal can be cleaned with a slightly damp sponge.
ACCESSORIES
Clean accessories with a wet, soapy sponge before rinsing and drying them:
avoid using abrasive detergents.
DRIP PAN
After using the grill, remove the pan from the oven. Pour the hot fat into a
container and wash the pan in hot water, using a sponge and washing-up
liquid.
If greasy residues remain, immerse the pan in water and detergent.
Alternatively, you can wash the pan in the dishwasher or use a commercial
oven detergent. Never put a dirty pan back into the oven.
EN 11
INSTRUCTION FOR REMOVAL AND CLEANING OF THE SIDE RACKS
1. Remove the wire racks by pulling them in the direction of the arrows (see below)
2. To clean the wire racks either put them in the dishwasher or use a wet sponge, ensuring that they are dried afterwards.
3. After the cleaning process install the wire racks in reverse order.
4.3 Maintenance
REMOVAL OF THE OVEN WINDOW
1. Open the front window.
2. Open the clamps of the hinge housing on the right and left side of the front window by pushing them downwards.
3. Replace the window by carrying out the procedure in reverse.
4.2 Hydro Easy Clean Function (Depends on the oven model)
The procedure uses steam to help remove remaining fat and food particles from the oven.HYDRO EASY CLEAN
1. Pour 300 ml of water into the container at the bottom of the oven.HYDRO EASY CLEAN
2. Set the oven function to Static ( )or Bottom ( )heater
3. Set the temperature to the icon HYDRO EASY CLEAN
4. Allow the program to operate for 30 minutes.
5. After 30 minutes switch off the program and allow the oven to cool down.
6. When the appliance is cool, clean the inner surfaces of the oven with a cloth.
Warning: Make sure that the appliance is cool before you touch it.
Care must be taken with all hot surfaces as there is a risk of burns.
Use distilled or drinkable water.
300 ml
LOW-E
1
2
3
1.
2.
3.
4.
5.
6.
7.
REMOVAL AND CLEANING OF THE GLASS DOOR
1. Open the oven door.
2.3.4. Lock the hinges, remove the screws and remove the upper metal cover by pulling it upwards.
5.6. Remove the glass, carefully extracting it from the oven door (NB: in pyrolytic ovens, also remove the second and third glass (if present)).
7. At the end of cleaning or substitution, reassemble the parts in reverse order.
On all glass, the indication "Low-E" must be legible and positioned on the left side of the door, close to the left-hand lateral hinge. In this way, the printed
label of the first glass will be inside the door.
EN 12
CHANGING THE BULB
1. Disconnect the oven from the mains supply.
2. Undo the glass cover, unscrew the bulb and replace it with a new bulb of the same type.
3. Once the defective bulb is replaced, replace the glass cover.
5. Troubleshooting
5.1 FAQ
PROBLEM POSSIBLE CAUSE SOLUTION
The oven does not heat up The clock is not set Set the clock
A cooking function and
temperature has not been set
Ensure that the necessary
settings are correct
The oven does not heat up
Steam and condensation on
the user interface panel
Clean with a microfiber cloth the user
interface panel to remove the
condensation layer
No reaction of the touch
user interface
EN 13
A
600 mm
560 mm
560 mm
If the mounting of the plinth does not allow air circulation, to
obtain the maximum performance of the oven it is necessary to
create an opening of 500x10 mm or the same surface in 5.000 mm2
GB
A
Opening / Apertura
460mm x 15 mm
INSTALLATION EN
Opening / Apertura
560mm x 45 mm
595 mm
595 mm
546 mm
22 mm
580 mm
560 mm
If the oven does not have a cooling fan, create an opening 460 mm x 15 mm
GB
560 mm
560 mm x 45 mm
A
560 mm
590 mm
42834688 • 70gr A4 • 09.2020 • REV_A
The manufacturer will not be responsible for any inaccuracy resulting from printing or transcript errors contained in this brochure. We reserve the right to
carry out modifications to products as required, including the interests of consumption, without prejudice to the characteristics relating to safety or
function.
EN
If the furniture is equpped with a bottom at the back part, provide an
opening for the power supply cable.
GB