Hoover HU300NXL 001 User Manual

Displayed below is the user manual for HU300NXL 001 by Hoover which is a product in the Stick Vacuums & Electric Brooms category. This manual has pages.

Related Manuals

Hoover OP30ALG 001 Manual

Hoover TX50PET 001 Manual

Hoover PC20PET 001 Manual

Hoover TH31 BO02 001 Manual

Hoover TH31 BO01 001 Manual

Hoover HU500GHM 001 Manual

Hoover HU500CPT 001 Manual

INSTRUCTION MANUAL

P10

Instructions for safe use.........................

1. Getting to know your cleaner................

2. Preparing your cleaner........................

3. Using your cleaner

3.1 Upright mode..............................

3.2 Accessories mode.........................

4. Cleaner maintenance

4.1 Dust bin & lters..........................

4.2 Brushbar....................................

4.3 Clearing a blockage......................

4.4 Belt change................................

5. Wiper blade.....................................

6. Troubleshooting................................

7. Important information........................

CONTENTS

MANUAL

LABEL

INSTRUCTIONS FOR SAFE USE

This appliance should only be used for domestic cleaning, as

described in this user guide. Please ensure that this guide is

fully understood before operating the appliance.

Do not leave the appliance plugged in. Always switch off and

remove the plug from the socket after use, or before cleaning

the appliance or any maintenance task.

This appliance can be used by children aged from 8 years and

above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have

been given supervision or instruction concerning use of the

appliance in a safe way and understand the hazards involved.

Children shall not play with the appliance. Cleaning and user

maintenance shall not be made by children without

supervision.

If the power cord is damaged stop using the appliance

immediately. To avoid a safety hazard, an authorised Hoover

service engineer must replace the power cord.

Keep hands, feet, loose clothing and hair away from rotating

brushes.

Use only attachments, consumables or spares recommended

or supplied by Hoover.

When using cleaning tools ensure that the appliance is kept in

the upright (parked) position. This will avoid possible damage

to the carpet or oor covering. When cleaning stairs, do not

position the appliance above you.

Static electricity: some carpets can cause a small build up of

static electricity. Any static discharge is not hazardous to

health.

Do not use your appliance out of doors or on any wet surface

or for wet pick up.

Do not pick up hard or sharp objects, matches, hot ashes,

cigarette ends or other similar items.

Do not spray with or pick up ammable liquids, cleaning uids,

aerosols or their vapours.

Do not run over the power cord when using your appliance or

remove the plug by pulling on the power cord.

Do not continue to use your appliance if it appears faulty.

Hoover service: To ensure the continued safe and efcient

operation of this appliance we recommend that any servicing

or repairs are only carried out by an authorised Hoover service

engineer.

Do not stand on or wrap the cord around arms or legs when

using your appliance.

Do not use the appliance to clean animals or people.

When using the cleaning tools, ensure to always steady the

appliance with your other hand. This will ensure that the

appliance does not fall while in use.

This product contains magnetic material.Please contact

your doctor if you have any questions on whether this

might affect your implanted medical device.

WARNING: A thermal cut out switches o the appliance to prevent overheating

if it is used when full or there is a blockage or dirty lters. If this should

happen then switch o, unplug and correct the fault. It will take approximately

45 minutes for the cut out to automatically reset.

The Environment

The symbol on this appliance indicates that this appliance may not

be treated as household waste. Instead it must be handed over to the

applicable collection point for the recycling of electrical and electronic

equipment. Disposal must be carried out in accordance with local

environmental regulations for waste disposal. For more detailed

information about treatment, recovery and recycling of this appliance, please

contact your local city oce, your household and waste disposal service or

the shop where you purchased the appliance.

This appliance complies with the European Directives 2014/35/EU,

2014/30/EU and 2011/65/EU.

CANDY HOOVER GROUP S.r.l. Via Privata Eden Fumagalli, 20861 Brugherio

(MB) Italy

1.GETTING TO KNOW YOUR CLEANER

Thank you for purchasing your

H-UPRIGHT300 Hoover upright

vacuum cleaner.

MAIN COMPONENTS:

A. Handle & tube

B. Dust bin release button

C. Dust bin top

D. Dust bin

E. Dust bin empty button

F. Active hose

G. Exhaust lter cover

H. Active hose release button

I. Suction regulator

J. Floor Nozzle

K. Cord storage hook lower

L. Left accessory holder

M. Rear accessory holder

N. Power cord

O. On/o button

P. Brushbar on/o button

Q. Cord storage hook upper

R. Tube release button

S. Handle end cap

2. PREPARING YOUR CLEANER

STEP 1:

Fit the handle & tube assembly into the

main product.

STEP 2:

Release the power cord from the cord

storage hook upper.

STEP 4:

Fit the 3-in-1 tool or short crevice tool

to the rear accessory holder dependant

on your model.

STEP 3:

Fit the mini turbo nozzle or dusting

brush to the left accessory holder

dependant on your model.

IMPORTANT: Accessories included are dependant on your model. Full specication

details are included on your product packaging.

3. USING YOUR CLEANER

3.1 UPRIGHT MODE

STEP 1:

Plug the power cord into the socket.

Place your foot onto the nozzle and pull the handle

backwards to your desired operating level.

STEP 4:

Adjust the suction by moving the SUCTION

REGULATOR left or right.

CARPET SETTING: Minimum suction level for

long pile carpets or rugs.

HARD FLOOR SETTING: maximum suction level

for hard oors or short pile carpets.

It can also be used to reduce the operating

push force

STEP 5:

Turn your cleaner o by pressing the ON/OFF

button. Remove the plug from the power

socket and wind the power cable around the

the cord storage hook upper and lower.

STEP 2:

Press the ON/OFF button to operate your

cleaner.

STEP 3:

Press the BRUSHBAR ON/OFF button to

activate the brush bar.

Brushbar ON is recommended for carpets.

Brushbar OFF is recommended for hard oors

and deep pile rugs.

To avoid damaging the

power cord during use,

t the power cord into

the cord clip on the

handle.

STEP 1:

Remove the active hose

from the hose retaining

clip.

STEP 3:

Remove the active hose

by pulling from the

nozzle.

3. USING YOUR CLEANER

3.2 ACCESSORIES MODE

To use your accessories, rstly release the active hose from the nozzle.

All accessories including the handle & tube will t

directly onto the active hose end for above oor

cleaning using the latch t mechanism.

To remove the handle & tube, press the tube release

button and pull upwards from the product.

Open the handle end cap and t directly onto the end of the

active hose using the latch t mechansim.

All other accessories will t to the end of the tube.

If your product is supplied with the

accessory hose, this can be added directly

to the active hose to create additional

reach. All other accessories will t to the

end of the hose.

IMPORTANT: Accessories included are dependant on your model. Full specication

details for your product are included on your product packaging.

IMPORTANT: When using cleaning tools, the cleaner must be kept in the upright position.

When cleaning stairs, hold or support the cleaner in a safe position whilst using the hose or handle & tube.

STEP 2:

Press and hold the active

hose release button.

Accessories:

1. Dusting brush

2. Short crevice tool

3. 3-in-1 Tool

4. Mini turbo nozzle

5. Long crevice tool

6. Accessory hose

4. CLEANER MAINTENANCE

4.1 DUST BIN & FILTERS

EMPTYING THE DUST BIN CLEANING THE EXHAUST FILTER

CLEANING THE PRE-MOTOR FILTER

STEP 2: Remove the

exhaust lter from your

cleaner.

STEP 6: Leave the lter

to dry for 24Hrs before

re-tting.

STEP 5: Clean the lter

using lukewarm water.

STEP 4: Remove any

excess debris from the

separation unit and lter.

STEP 3: Remove any excess

debris from the lter.

STEP 4: Clean the lter

using lukewarm water. STEP 5: Leave the lter

to dry for 24Hrs before

re-tting.

IMPORTANT: Do not ret the lters until they are completely dry.

To ret the lters and dust bin to your cleaner, follow the above

intructions in reverse.

STEP 2: Remove the

pre-motor lter from the

separation unit.

STEP 3: Remove the

separation unit from the

dust bin.

STEP 1: Rotate the dust

bin top anti-clockwise and

remove from the dust bin.

STEP 2: Remove the

dust bin assembly from

your cleaner.

STEP 3: Press the dust

bin empty button over a

rubbish bin to empty.

STEP 1: Press and hold

the dust bin release

button.

STEP 1: Rotate the exhaust

filter cover anti-clockwise and

remove from the cleaner.

IMPORTANT: Before performing any maintenance task, always ensure your product is

switched o and unplugged from the electricity supply.

IMPORTANT: To maintain optimum performance is recommended to

empty the bin when full, clear any blockages and to wash lters on a

regular basis or at least once a month.

4. CLEANER MAINTENANCE

4.3 CLEARING A BLOCKAGE

FLOOR NOZZLE:

Turn the cleaner over and

rotate the brushbar to

visually identify any

obstructions and remove.

ACCESSORIES:

Visually check all accessories

for any obstructions and

remove.

HANDLE & TUBE:

Visually check both ends

of the handle for any

obstructions and remove.

ACTIVE HOSE:

Release the active hose from

the nozzle, extend the hose

fully and shake vigorously to

release any obstruction.

MINI TURBO NOZZLE:

Open the nozzle cover, visually

check for any obstructions and

remove.

STEP 3:

Remove the brushbar guard.

STEP 1:

Turn the cleaner over to access

the nozzle.

STEP 2:

Using a coin or screwdriver,

rotate 3 x locking clips 90°to

unlock the brush guard.

STEP 4:

Remove the brushbar from

nozzle by unhooking from

the belt.

STEP 5:

Remove any debris from the

brushbar with scissors.

IMPORTANT: Before performing any maintenance task, always ensure your product is

switched o and unplugged from the electricity supply.

If your cleaner is not picking up eciently, the brushbar may need cleaned.

To ret the brushbar to your cleaner, follow the above instructions in reverse.

4. CLEANER MAINTENANCE

4.2 BRUSHBAR

5. WIPER BLADE - OPTIONAL

STEP 1:

Turn the cleaner over to

access the nozzle.

STEP 2:

Grip the wiper blade and

locate into the slot on the

oor nozzle.

STEP 3:

Slide the wiper blade into

the slot until fully located.

The front wiper blade supplied in the instruction manual package is not necessary for normal

cleaning. Fitting the wiper blade will improve the energy eciency of the product, but will make the

product more dicult to push and manoeuvre.

STEP 3:

Remove the brushbar

guard.

STEP 1:

Turn the cleaner over to access

the nozzle.

STEP 2:

Using a coin or screwdriver,

rotate 3 x locking clips 90°to

unlock the brush guard.

STEP 4:

Remove the brushbar

from the nozzle.

STEP 5:

Remove the belt, check

if worn and replace if

required.

IMPORTANT: Before performing any maintenance task, always ensure your product is

switched o and unplugged from the electricity supply.

If your cleaner is still not picking up eciently after cleaning the lters, brush bar & clearing blockages, the belt may be worn and need replacing.

Please ensure to carry out lter cleaning and check for blockages rst.

To ret the belt and brushbar to your cleaner, follow the above instructions in reverse.

4. CLEANER MAINTENANCE

4.4 BELT CHANGE

P10

6. TROUBLESHOOTING 7. IMPORTANT INFORMATION

Hoover Spares and Consumables

Always replace parts with genuine Hoover spares. These are available from your

local Hoover dealer or direct from Hoover. When ordering parts always quote

your model number.

Quality

Hoover’s factories have been independently assessed for quality. Our products

are made using a quality system which meets the requirements of ISO 9001.

Your Guarantee

The guarantee conditions for this appliance are as dened by our representative

in the country in which it is sold. Details regarding these conditions can be

obtained from the dealer from whom the appliance was purchased. The bill of

sale or receipt must be produced when making any claim under the terms of this

guarantee.

Subject to change without notice.

The following is a list of commonly encountered problems and solutions.

If there is any doubt call the Hoover Service Oce for advice. They may be

able to assist you over the telephone. A service charge will be made if the

cleaner is examined and found to be in working order, has not been assembled

in accordance with these instructions or has been used incorrectly.

Fault Solutions

Is there a working electricity supply to

the cleaner?

Check the power supply with another

appliance.

Cleaner is not picking up debris? Empty the dust bin and clean the

lters. (see page 7)

Check your brushbar for excessive

debris and blockages (see page 8)

Check your nozzle, active hose and

accessories for blockages (see page 8)

Brushbar is not turning? Check your brushbar for excessive

debris and blockages (see page 8)

Check if your belt needs replaced.

(see page 9)

Cleaner cuts out? Your cleaner is tted with a thermal

cut out to prevent overheating by

automatically turning your cleaner

o.

Once activated, as a safety

precaution, your cleaner cannot be

turned on again for 45 mins.

If your cleaner does cut out, perform

all maintenance tasks contained in

the manual before resuming.(see

pages 7,8,9)

Printed in P.R.C.

Part No. : 48033778/02