Hotpoint BI WMHG 71484 UK User Manual
Displayed below is the user manual for BI WMHG 71484 UK by Hotpoint which is a product in the Washing Machines category. This manual has pages.
Related Manuals
www.hotpoint.eu/register
User Manual
1 “ON/OFF” button
2 Programme selector
3 “Start/Pause” button
4 “Spin Speed” button
5 “Multi Rinse” button
6 “Cleaning Action” button
7 “Start Delay” button
8 “Energy saver” / “Key lock“
button
9 “Temperature” button
DISPLAY INDICATORS
Door locked
Energy saver activated
Pre-wash activated
Start Delay activated
Key lock activated
Washing phase
Indicates washing phase of the cycle
Failure: Call Service
Refer to Troubleshooting section
Failure: Water lter clogged
Water cannot be drained; water lter
might be blocked
Failure: No water
No or not sucient inlet water.
In the event of any failure, refer to the
“TROUBLESHOOTING” section
THANK YOU FOR BUYING A HOTPOINT PRODUCT.
In order to receive a more complete assistance,
please register your appliance on
www.hotpoint.eu/register
Before using the appliance carefully read the Safety Instruction.
Before using the machine, it is imperative that the transport bolts are removed. For more detailed
instructions on how to remove them, see the Installation Guide.
CONTROL PANEL
PROGRAMME CHART
EN
Quick guide
PRODUCT DESCRIPTION
1. Worktop
2. Detergent dispenser
3. Control panel
4. Door handle
5. Door
6. Water lter
7. Adjustable feet (4)
DETERGENT DISPENSER
Compartment 1: Pre-wash detergent
(powder)
Compartment 2: Washing detergent
(powder or liquid)
Compartment 3: Additives (fabric softeners,
etc.)
The fabric softener must not exceed the “MAX”
level.
! Use powder detergent for white cotton
garments, for pre-washing, and for washing at
temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
12
3
1.
3.
2.
5.
4.
6.
7.
21 5
3
9
47
8
6
For all testing institutes:
2) Long cotton cycle: set cycle 7 at a temperature of 40°C.
3) Long synthetics cycle: set cycle 8 at a temperature of 40°C.
* By selecting the cycle and excluding the spin cycle, the washing machine will drain only.
** The duration of the wash cycles can be checked on the display.
The cycle duration indicated on the display or instruction manual is an estimate based on
standard conditions. The actual duration may vary in relation to several factors, such as
the temperature and pressure of the incoming water, ambient temperature, amount of
detergent, load quantity and type, load balancing and any additional options selected.
1) Test wash cycle in compliance with regulation 1061/2010:
This cycle is designed for normally soiled cotton loads and is the most ecient in terms of
both electricity and water consumption; it should be used for garments washable at 60°C
or at 40°C. The actual washing temperature may dier from the indicated value.
Maximum load 7 kg
Power input in o mode 0.5 W / in left-on mode 8 W
Detergents and Addi-
tives
Recommended
detergent
Residual
dampness %
Energy con-
sumption kWh
Total water l
Wash cycle Temperature Maximum
spin
(r.p.m.)
Maximum
load (kg)
Duration
(minutes)
Pre-
wash Wash Fabric
softener Powder Liquid
Default Range 1 2 3
1 Anti Stain 100 40 °C - 40 °C 1400 7,0 ** – – – – –
2 Anti Stain Quick 40 °C - 40 °C 1200 3,5 ** – –– – –
3 White 60 °C - 90 °C 1400 7,0 ** (90°) – – – –
4 Bed Linen 60 °C - 60 °C 1400 7,0 ** – – – – –
5Eco Cotton (1) 60 °C 60° C 1400 7,0 270 – 53 0,82 52,5
40°C 1400 7,0 220 – 53 0,97 75
6 Mixed 40 °C - 40 °C 1000 3,5 ** – –– – –
7 Cotton (2) 40 °C - 60 °C 1400 7,0 220 – – 53 0,97 75
8 Synthetics (3) 40 °C - 60 °C 1200 4,0 195 – – 33 0,75 72
9 Coloureds 40 °C - 40 °C 1400 7,0 ** – – – – –
10 Fast 30 min 30 °C - 30 °C 800 3,0 30 – –71 0,19 29
11 Wool 40 °C - 40 °C 800 1,5 ** – –– – –
12 Dark 30 °C - 30 °C 800 4,0 ** – –– – –
13 Ultradelicates 30 °C - 30 °C 0 1,0 ** – –– – –
14 Duvet 30 °C - 30 °C 1000 2,0 ** – –– – –
Rinse + Spin – – 1400 7,0 ** ––– – – – –
Spin + Drain * – – 1400 7,0 ** –– – – – – – –
Required dosage Optional dosage
PROGRAMMES
Follow the instructions on the symbols of the garment’s wash
care label. The value indicated in the symbol is the maximum
recommended temperature for washing the garment.
Anti Stain 100
This cycle is suitable to heavily-soiled garments with resistant colours. It
ensures a washing class that is higher than the standard class (A class).
When running the programme, do not mix garments of dierent colours.
We recommend the use of powder detergent. Pre-treatment with special
additives is recommended if there are obstinate stains
Anti Stain Quick
This cycle is ideal for washing daily stains in 45’. It is ideal for mixed fabrics
and coloured garments.
White
For washing normally to heavily soiled towels, underwear, table
and bed linen, etc in resilient cotton and linen. Only when the
temperature is selected at 90°C the cycle is provided with a prewash
phase before main washing phase. In this case it is recommended to
add detergent both, in the prewash and main wash section.
Bed Linen
For washing home linen in a single cycle. It optimises the use of fabric
softener and allows for saving time and electricity. We recommend the
use of powder detergent.
Eco Cotton
Suitable for washing moderately soiled cotton garments. At 40°C and
60°C it is the standard cycle for washing cotton garments, and is the most
ecient in terms of combined water and electricity consumption.
Mixed
To wash mixed and coloured items together.
Cotton
Suitable for washing towels, underwear, table cloths, etc. made of
resistant linen and cotton that are moderately to heavily soiled.
Synthetics
Suitable for washing moderately soiled garments made of synthetic bres
(e.g. polyester, polyacrylic, viscose, etc.) or mixed synthetic-cotton bres.
Coloureds
For washing coloured cotton garments. This programme is optimised to
keep colours bright even after repeated washing.
Fast 30 min
For washing lightly soiled garments in a short time. Not suitable for wool,
silk and garments to be washed by hand.
Wool - Woolmark Apparel Care - Green:
The Wool wash cycle of this machine has been approved by The
Woolmark Company for the washing of wool garments
labelled as “hand wash” provided that the products are
washed according to the instructions on the garment
label and those issued by the manufacturer of this
washing machine (M1126). The Woolmark logo is a
Certication mark in many countries.
Dark
For washing dark-coloured garments. The wash cycle is designed to
preserve dark colours over time.
We recommend using a liquid detergent for best results, preferably when
washing dark-coloured garments.
Ultradelicates
For washing very delicate garments. It is advisable to turn the garments
inside out before washing them. For best results, use liquid detergent on
delicate garments.
Duvet
Suitable for washing clothing padded with goose down, such as single
duvets (weighing under 2 kg), cushions or down jackets. Duvets should
be loaded into the drum with their edges folded inwards and no more
than ¾ of the total drum volume should be used up. For best results, it is
advisable to use liquid detergent to be poured into the detergent drawer.
Rinse + Spin
Designed for rinsing and spinning.
Spin + Drain
Designed for spinning and draining the water.
FIRST TIME USE
To remove any manufacturing debris select the 3 programme at a
temperature of 90°C. Pour a small quantity of detergent powder into the
main wash 2 compartment of the detergent dispenser (maximum 1/3 of
the quantity the detergent manufacturer recommends for lightly soiled
laundry). Start the programme without adding any laundry.
DAILY USE
Prepare your laundry according to the recommendations in the “HINTS
AND TIPS” section. Load the laundry, close the door, open the water tap
and press the “ON/OFF” button to switch the washing machine on, the
“Start/Pause” button ashes. Turn the programme selector to the
desired programme and select any option if needed. The temperature and
spin speed can be changed by pressing the “Temp.” button or the “Spin
Speed” button. Pull out the detergent dispenser and add the detergent
(and additives/softener) now. Observe the dosing recommendations on the
detergent pack. Then close the detergent dispenser and press the “Start/
Pause” button. The “Start/Pause” button will lights up and the door
will be locked.
PAUSE A RUNNING PROGRAMME
To pause the wash cycle, press the “Start/Pause” ; the indicator light will
go o and the remaining time on display ash. To start the wash cycle from
the point at which it was interrupted press the button again.
OPEN THE DOOR, IF REQUIRED
After starting a programme, the “Door locked” indicator lights up to
show that the door can not be opened. As long as a wash programme is
running, the door remains locked. To open the door while a programme is
in progress, press the “Start/Pause” to pause the programme. Provided
the water level and/or temperature is/are not too high, the “Door locked”
indicator light goes o and you can open the door. For example to add
or remove laundry. Press the “Start/Pause” button again to continue the
programme.
PROGRAMME END
The “Door locked” indicator light goes o and the display shows “End”.
To switch o the washing machine after programme ends press the
“ON/OFF” button, the lights goes o. If you do not press “ON/OFF”
button, the washing machine will switch o automatically after about a
half of an hour. Close the water tap, open the door and unload the washing
machine. Leave the door ajar to allow the drum to dry.
OPTIONS
! If the selected option is incompatible with the programme set,
the incompatibility will be signalled by a buzzer (3 beeps) and the
corresponding indicator light will ash.
! If the selected option is incompatible with another previously set
option, only the most recent selection will remain active.
Energy saver
This option saves energy by not heating the water used to wash your
laundry – an advantage both to the environment and to your energy bill.
Instead, intensied wash action and water optimisation ensure great wash
results in the same average time of a standard cycle.
For the best washing results we recommend the usage of a liquid
detergent.
Start Delay
To set the selected programme to start at a later time, press the button
to set the desired delay time. Symbol lights on the display when this
fuction is enabled. To cancel the delayed start, press the button again until
the value ‚ ‘‘0‘‘ is shown on the display.
Multi Rinse
By selecting this option, the eciency of the rinse is increased and optimal
detergent removal is guaranteed. It is particularly useful for sensitive skin.
Press the button once, two or three times to select an additional 1 ,
2 or 3 rinses after the standard cycle rinse and remove all traces
of detergent. Press the button again to go back to the “Normal rinse” rinse
type.
Cleaning Action
Option “Cleaning Action” makes it possible to optimise washing based on
the level of soil in the fabrics and on desired wash cycle intensity.
For heavily-soiled garments press “Cleaning Action” button until the “ ”
level is reached. This level ensures a high-performance wash due to a larger
quantity of water used in the initial phase of the cycle and due to increased
drum rotation. It is useful when removing the most stubborn stains. For
lightly-soiled garments or a more delicate treatment of the fabrics, press
“Cleaning Action” button until the “ ” level is reached. The cycle will
reduce drum rotation to ensure washing results that are perfect for delicate
garments.
Temperature
Every programme has a predened temperature. If you want to change the
temperature, press the “Temp.” button. The value appears on the display.
Spin Speed
Every programme has a predened spin speed. If you want to change the
spin speed, press the “Spin Speed” button. The value appears on the display.
KEY LOCK
To lock the control panel, press and hold the “Energy saver”
button for approximately 3 seconds. The symbol will light up
on the display to indicate that the control panel has been locked
(with the exception of the “ON/OFF“ button). This prevents
unintentional changes to programmes, especially with children
near the machine. To unlock the control panel, press and hold the
“Energy saver” button for approximately 3 seconds .
HINTS AND TIPS
Sort your laundry according to
Type of fabric/care label (cotton, mixed bres, synthetics, wool,
handwash items). Colour (separate coloured and white items,
wash new coloured items separately). Delicates (wash small items
– like nylon stockings – and items with hooks – like bras – in a
cloth bag or pillow case with zip).
Empty all pockets
Objects like coins or lighters can damage your laundry as well as the
drum.
CLEANING & MAINTENANCE
For any cleaning and maintenance, switch o and unplug the
washing machine. Do not use ammable uids to clean the
washing machine.
Cleaning the outside of the washing machine
Use a soft damp cloth to clean the outer parts of the washing
machine. Do not use glass or general purpose cleaners, scouring
powder or similar to clean the control panel – these substances
might damage the printing.
TRANSPORT AND HANDLING
Never lift the washing machine by holding it at the worktop.
Pull out the mains plug, and close the water tap. Make sure that
door and detergent dispenser are properly closed. Disconnect the
inlet hose from the water tap, and remove the drain hose from
your draining point. Remove all rest water from the hoses, and x
them so that they cannot get damaged during transport. Ret the
transport bolts. Follow the instructions for removing the transport
bolts in the Installation Guide in reverse order.
Quick guide
TROUBLESHOOTING
The washing machine may sometimes not work properly for certain reasons. Before calling the After-sales service, it is recommended to
check to see if the problem can be easily resolved using the following list.
Anomalies: Possible causes / Solution:
The washing machine does not turn on. • The plug is not inserted into the electrical outlet, or not enough to make contact.
• There has been a power failure.
The wash cycle does not start.
• The door is not fully closed.
• The “ON/OFF” button has not been pressed.
• The “Start/Pause” button has not been pressed.
• The water tap is not open.
• A “Start Delay” has been set.
The washing machine does not ll with
water (the message “h2o” is shown on
the display).
• The water intake hose is not connected to the tap.
• The hose is bent.
• The water tap is not open.
• The mains water supply has been shut o.
• There is not enough pressure.
• The “Start/Pause” button has not been pressed.
The washing machine loads and drains
water continuously.
• The drain hose has not been installed at 65 to 100 cm from the ground.
• The end of the drain hose is immersed in water.
• The drain connector on the wall does not have an air vent.
• If the problem persists after having performed these checks, close the water tap, shut o the
washing machine, and call the After-sales service. If the dwelling is located on one of the
uppermost oors of a building, a siphon eect can sometimes occur, thus causing the washing
machine to load and drain water continuously. Special anti-siphon valves are available on the
market to prevent these types of problems.
The washing machine does not drain or
does not spin.
• The programme does not include the draining function: with certain programmes it must be
activated manually.
• The drain hose is bent.
• The drain line is obstructed.
The washing machine vibrates
excessively during the spin cycle.
• At the time of installation, the drum was not properly unblocked.
• The washing machine is not level.
• The washing machine is squeezed between furniture and the wall.
The washing machine leaks water.
• The water intake hose has not been tightened properly.
• The detergent dispenser is clogged.
• The drain hose has not been properly fastened.
The machine is locked and the display
ashes, indicating an error code (e.g.
F-01, F-..).
• Shut o the machine, disconnect the plug from the outlet, and wait about 1 minute before
turning it back on.
• If the problem persists, call the After-sales service.
Too much foam is formed.
• The detergent is not compatible with the washing machine (it must bear the wording “for
washing machines”, “for hand washing and washing machines”, or something similar).
• The dosage was excessive.
Door is locked, with or without
failure indication, and the
programme does not run.
• Door is locked in case of power breakdown. Programme will continue automatically as soon as
the mains is available again.
• Washing machine is in a standstill. Programme will continue automatically after the origin of the
standstill does not persist anymore.
DEMO MODE: to deactivate this function, switch the washing machine OFF. Than press and hold “Start/Pause” button, within 5 seconds press also
“ON/OFF” button and hold both buttons for 2 seconds.
CLEANING & MAINTENANCE
For any cleaning and maintenance, switch o and unplug the washing machine.
Do not use ammable uids to clean the washing machine.
CLEANING THE OUTSIDE OF THE WASHING MACHINE
Use a soft damp cloth to clean the outer parts of the washing
machine.
Do not use glass or general purpose cleaners, scouring
powder or similar to clean the control panel – these
substances might damage the printing.
CHECKING THE WATER SUPPLY HOSE
Check the inlet hose regularly for brittleness and cracks. If
damaged, replace it by a new hose available through our
After-Sales Service or your specialist dealer.
Depending on the hose type:
If the inlet hose has a transparent coating, periodically check
if the colour intensies locally. If yes, the hose may have a leak
and should be replaced.
For water stop hoses: check the small safety valve inspection
window (see arrow). If it is red, the water stop function was
triggered, and the hose must be replaced by a new one.
For unscrewing this hose, press the release button (if
available) while unscrewing the hose.
CLEANING THE MESH FILTERS IN THE WATER SUPPLY HOSE
1. Close water tap and unscrew the inlet hose.
1
2
2. Clean the mesh lter at the hose’s end carefully with a
ne brush.
3. Now unscrew the inlet hose on the back of the washing
machine by hand. Pull out the mesh lter from the valve
on the back of the washing machine with pliers and
carefully clean it.
4. Insert the mesh lter again. Connect the inlet hose to
water tap and washing machine again. Do not use a tool
to connect the inlet hose. Open the water tap and check
that all connections are tight.
2
1
CLEANING THE DETERGENT DISPENSER
CLEANING THE WATER FILTER / DRAINING RESIDUAL WATER
Switch o and unplug the washing machine before cleaning the water lter or draining residual water. If you used a hot
wash programme, wait until the water has cooled down before draining any water.
Clean the water lter regularly, to avoid that the water cannot drain after the wash due to obstruction of the lter.
If the water cannot drain, the display indicates that the water lter may be clogged.
1. Container for the drained water:
Place a low and wide container under the water lter in
order to collect the residual water.
2. Drain the water:
Slowly turn the lter counter-clockwise until all the water
has come out. Allow the water to ow out without
removing the lter. Once the container is full, close the
water lter by turning it clockwise. Empty the container.
Repeat the procedure until all the water has been drained.
3. Remove lter: Lay a cotton cloth beneath the water lter,
which can absorb a small amount of rest water. Then
remove the water lter by turning it out anticlockwise.
4. Clean the water lter: remove residues in the lter and
clean it under running water.
5. Insert the water lter: Reinsert the water lter again by turning it
in clockwise direction. Make sure to turn it in as far as it goes; the
lter handle must be in vertical position. To test water tightness
of the water lter, you can pour about 1 liter of water into the
detergent dispenser.
Remove the dispenser by raising it and
pulling it out (see gure).
Wash it under running water; this
operation should be repeated frequently.
1
2
1
2
TRANSPORT AND HANDLING
Never lift the washing machine by holding it at the worktop.
1. Pull out the mains plug, and close the water tap.
2. Make sure that door and detergent dispenser are properly
closed.
3. Disconnect the inlet hose from the water tap, and remove
the drain hose from your draining point. Remove all rest
water from the hoses, and x them so that they cannot get
damaged during transport.
4. Ret the transport bolts. Follow the instructions for
removing the transport bolts in the “Installation Guide” in
reverse order.
Important: Do not transport the washing machine without
having xed the transport bolts.
AFTERSALES SERVICE
BEFORE CALLING THE AFTERSALES SERVICE
1. See if you can solve the problem by yourself with the help
of the suggestions given in the TROUBLESHOOTING
2. Switch the appliance o and back on again to see if the
fault persists.
IF AFTER THE ABOVE CHECKS THE FAULT STILL
OCCURS, GET IN TOUCH WITH THE NEAREST
AFTERSALES SERVICE
To receive assistance, call the number shown on the warranty
booklet or follow the instructions on the website
http://docs.hotpoint.eu.
When contacting our Client After sales service, always specify:
• a brief description of the fault;
• the type and exact model of the appliance;
xxxxxxxxxxxx
• the service number (number after the word Service on the
rating plate).
• your full address;
• your telephone number.
If any repairs are required, please contact an authorised after-
sales service (to guarantee that original spare parts will be used
and repairs carried out correctly).
1. 2. 3.
4. 5.
150 ml
100 ml
50 ml
10 mm - 0,39 inch
2 cm - 0,7 inch
6. 7.
10. 11.
12.
13. 14.
max 100 cm
39 inch
min 65 cm
25 inch
max 100 cm
39 inch
min 65 cm
25 inch
max 100 cm
39 inch
min 65 cm
25 inch
9.8.
max 0,5 cm
max 0,2 inch
EN
Before using the appliance, read these safety in-
structions. Keep them nearby for future reference.
These instructions and the appliance itself provide
important safety warnings, to be observed at all ti-
mes. The manufacturer declines any liability for failure
to observe these safety instructions, for inappropriate
use of the appliance or incorrect setting of controls.
Very young children (0-3 years) should be kept
away from the appliance. Young children
(3-8years) should be kept away from the
appliance unless continuously supervised.
Children from 8years old and above and persons
with reduced physical, sensory or mental
capabilities or lack of experience and knowledge
can use this appliance only if they are supervised
or have been given instructions on safe use and
understand the hazards involved. Children must
not play with the appliance. Cleaning and user
maintenance must not be carried out by children
without supervision. Never open the door forcibly
or use it as a step.
PERMITTED USE
CAUTION: The appliance is not intended to be
operated by means of an external switching
device, such as a timer, or separate remote
controlled system.
This appliance is intended to be used in
household and similar applications such as: sta
kitchen areas in shops, oces and other working
environments; farm houses; by clients in hotels,
motels, bed & breakfast and other residential
environments.
Do not load the machine above the maximum
capacity (kg of dry cloth) indicated in the
programme table.
This appliance is not for professional use. Do
not use the appliance outdoors.
Do not use any solvents (e.g. turpentine,
benzene), detergents containing solvents,
scouring powder, glass or general purpose
cleaners, or ammable uids; do not machine
wash fabrics that have been treated with solvents
or ammable liquids.
INSTALLATION
The appliance must be handled and installed by
two or more persons- risk of injury. Use protective
gloves to unpack and install- risk of cuts.
If you want to stack a dryer on top of your
washing machine, rst contact our After-Sales
Service or your specialist dealer to verify whether
this is possible. This is only possible if the dryer is
attached to the washing machine by means of
appropriate stacking kit available through our
After- Sales Service or your specialist dealer.
Move the appliance without lifting it by the
worktop or top lid.
Installation, including water supply (if any) and
electrical connections and repairs must be carried
out by a qualied technician. Do not repair or
replace any part of the appliance unless
specically stated in the user manual. Keep
children away from the installation site. After
unpacking the appliance, make sure that it has not
been damaged during transport. In the event of
problems, contact the dealer or your nearest
After-sales Service. Once installed, packaging
waste (plastic, styrofoam parts etc.) must be
stored out of reach of children- risk of suocation.
The appliance must be disconnected from the
power supply before any installation operation-
risk of electric shock. During installation, make
sure the appliance does not damage the power
cable - risk of re or electric shock. Only activate
the appliance when the installation has been
completed.
Do not install your appliance where it may be
exposed to extreme conditions, such as: poor
ventilation, temperatures below 5 °C or above 35
°C.
When installing the appliance make sure that
the four feet are stable and resting on the oor,
adjusting them as required, and check that the
appliance is perfectly to level using a spirit level.
If the appliance is being installed on wood or
“oating” oors (certain parquet and laminate
materials), secure a 60x60x3cm (at least) sheet
of plywood to the oor then place the appliance
on top of this.
Connect the water inlet hose(s) to the water
supply in accordance with the regulations of your
local water company.
For cold ll only models: do not connect to the
hot water supply.
For models with hot ll: the hot water inlet
temperature must not exceed 60°C.
The washing machine is tted with transport
bolts to prevent any possible damage to the
interior during transport. Before using the
machine, it is imperative that the transport bolts
are removed. After their removal, cover the
openings with the 4 enclosed plastic caps.
After installation of the device, wait a few hours
before starting it so that it acclimates to the
environmental conditions of the room.
Make sure that the ventilation openings in the
base of your washing machine (if available on
your model) are not obstructed by a carpet or
other material.
Use only new hoses to connect the appliance
to the water supply. The old hose-sets should not
be reused.
The supply water pressure must be in the 0.1-1
Mpa range.
SAFETY INSTRUCTIONS IMPORTANT TO BE READ AND OBSERVE
ELECTRICAL WARNINGS
It must be possible to disconnect the appliance
from the power supply by unplugging it if plug is
accessible, or by a multi-pole switch installed
upstream of the socket in accordance with the
wiring rules and the appliance must be earthed in
conformity with national electrical safety standards.
Do not use extension leads, multiple sockets or
adapters. The electrical components must not be
accessible to the user after installation. Do not use
the appliance when you are wet or barefoot. Do
not operate this appliance if it has a damaged
power cable or plug, if it is not working properly, or
if it has been damaged or dropped.
If the supply cord is damaged, it must be
replaced with an identical one by the manufacturer,
its service agent or similarly qualied persons in
order to avoid a hazard - risk of electric shock.
CLEANING AND MAINTENANCE
WARNING: Ensure that the appliance is switched
o and disconnected from the power supply
before performing any maintenance operation;
never use steam cleaning equipment - risk of
electric shock.
DISPOSAL OF PACKAGING MATERIALS
The packaging material is 100% recyclable and is marked with the
recycle symbol .
The various parts of the packaging must therefore be disposed of
responsibly and in full compliance with local authority regulations
governing waste disposal.
DISPOSAL OF HOUSEHOLD APPLIANCES
This appliance is manufactured with recyclable or reusable materials.
Dispose of it in accordance with local waste disposal regulations.
For further information on the treatment, recovery and recycling of
household electrical appliances, contact your local authority, the
collection service for household waste or the store where you purchased
the appliance. This appliance is marked in compliance with European
Directive 2012/19/EU, Waste Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent
negative consequences for the environment and human health.
The symbol on the product or on the accompanying documentation
indicates that it should not be treated as domestic waste but must be
taken to an appropriate collection center for the recycling of electrical
and electronic equipment.
INSTRUCTIONS FOR THE FITTER
Mounting the wooden panel onto the door
and inserting the machine into cabinets:
In the case where the machine must be shipped
for nal installation after the wooden panel has
been mounted, we suggest leaving it in its
original packaging. The packaging was designed
to make it possible to mount the wooden panel
onto the machine without removing it
completely (see gures below).
The wooden panel that covers the face of the
machine must not be less than 13 mm in
thickness and can be hinged on either the right
or left. For the sake of practicality when using the
machine, we recommend that the panel be
hinged on the same side as the door for the
machine itself - the left.
Door Mounting Accessories (Fig. 1-2-3-4-5).
Fig. 1
N° 2 Hinges
N° 1 Magnet N° 1 Magnet plate
N° 1 Rubber plug
N° 2 Hinge Supports
N° 4 Spacers
Fig. 2
Fig. 3 Fig. 4
Fig. 5 Fig. 4/B
- No. 6 type A self-threading screws, l =13 mm.
- No. 2 type B metric, countersunk screws, l =25;
for fastening the magnet plate to the cabinet.
- No. 4 type C metric screws, l =15 mm; for
mounting the hinge supports to the cabinet.
- No. 4 type D metric screws, l =7 mm; for
mounting the hinges on the supports.
Mounting the Parts onto the Face of the
Machine.
- Fit the hinge supports to the appliance front
panel, positioning the hole marked with an arrow
in g. 1 so that it is on the inner side of the front
panel. Fit a spacer (g. 4/B) between the surfaces
using type C screws.
- Fit the magnet plate at the top of the opposite
side, using type B screws to x two spacers (g.
4/B) between the plate and the surface.
EN
AB
CD
E
Tur seite
Using the Drilling Template.
- To trace the positions of the holes on the left-
hand side of the panel, align the drilling template
to the top left side of the panel using the lines
traced on the extremities as a reference.
- To trace the positions of the holes on the right-
hand side of the panel, align the drilling template
to the top right side of the panel.
- Use an appropriately sized router to mill the holes
for the two hinges, the rubber plug and the magnet.
Mounding the Parts onto the Wooden Panel (Door).
- Insert the hinges into the holes (the movable part
of the hinge must be positioned facing away from
the panel) and fasten them with the 4 type A screws.
- Insert the magnet into the top hole on the
opposite side of the hinges and fasten it with the
two type B screws.
- Insert the rubber plug into the bottom hole.
The panel is now ready to be mounted onto the
machine.
Mounting the Panel into the machine.
Insert the nib of the hinge (indicated by the arrow
in g. 2) into the hole for the hinge and push the
panel towards the front of the machine. Fasten
the two hinges with the type D screws.
Fastening the plinth guide.
If the machine is installed at the end of a set of
modular cabinets, mount either one or both of the
guides for the base molding (as shown in g. 8).
Adjust them for depth based on the position of
the base molding, and, if necessary, fasten the
base to the guides (g. 9).
This is how to assemble the plinth guide (g. 8):
Fasten angle P using screw R, insert plinth guide Q
into the special slot and once it is in the desired
position, lock it in place using angle P and screw R.
Inserting the machine into the Cabinet.
- Push the machine into the opening, aligning it
with the cabinets (g. 6).
- Regulate the adjustable feet to raise the machine
to the appropriate height.
- To adjust the position of the wooden panel in
both the vertical and horizontal directions, use the
C and D screws, as shown in g. 7.
Important: close the lower part of the appliance front
by ensuring that the plinth rests against the oor.
Fig. 8 Fig. 9
Accessories provided for the height adjustment.
The following can be found
inside the polystyrene lid (g.
10): 2 crossbars (G), 1 strip
(M)
the following can be found
inside the appliance drum:
4 additional feet (H),
4 screws (I),
4 screws (R),
4 nuts (L),
2 plinth guides (Q)
Adjusting the appliance height.
The height of the appliance can be adjusted (from
815 mm to 835 mm), by turning the 4 feet.
Should you require the appliance to be placed
higher than the above height, you need to use the
following accessories to raise it to up to 870 mm:
the two crossbars (G); the 4 feet (H); the 4 screws
(I); the 4 nuts (L) then perform the following
operations (g. 11):
remove the 4 original feet, place a crossbar G at
the front of the appliance, fastening it in place
using screws I (screwing them in where the original
feet were) then insert the new feet H.
Repeat the same operation at the back of the
appliance.
Now adjust feet H to raise or lower the appliance
from 835 mm to 870 mm.
Once you have reached the desired height, lock
nuts L onto crossbar G.
To adjust the appliance to a height between 870
mm and 900 mm, you need to mount strip M,
adjusting feet H to the required height.
Insert the strip as follows:
loosen the three screws N situated at the front of
the Top cover of the appliance, insert strip M as
shown in g. 12, then fasten screws N.
D
C
C
Fig. 6 Fig. 7
LI
H
G
M
Fig. 11 Fig. 12
570
min
815
545
595
820 ÷ 900
600 min
Fig. 10
11338864