Hotpoint HFP 4O22 WG C X UK User Manual
Displayed below is the user manual for HFP 4O22 WG C X UK by Hotpoint which is a product in the Dishwashers category. This manual has pages.
Related Manuals
INSTRUCTION FOR USE
2
EN
THANK YOU FOR PURCHASING A HOTPOINT PRODUCT.
To receive more comprehensive help and support, please register your product at:
www.hotpoint.eu/register
1 3 4 5 6 7 8 9 102 11 12
1. Upper rack
2. Foldable aps
3. Upper rack height adjuster
4. Upper sprayer arm
5. Space Zone support
6. Lower rack
7. Cutlery basket
8. Lower sprayer arm
9. Filter Assembly
10. Salt reservoir
11. Detergent and Rinse Aid dispensers
12. Rating plate
13. Control panel
1. ON/OFF button
2. INFO button. Provide info for selected cycle
3. 3D ZONE WASH button
4. ZONE WASH button
5. DISPLAY - Indicators area
6. CYCLES 6 buttons for direct acces popular cycles
7. EXTRA CYCLES button. Access to other cycles
8. DISPLAY - Information area
9. PREVIOUS button for options/settings
10. OK button. Select/change options and settings
11. NEXT button for options/settings
12. START/PAUSE button
1
4
6
5
11
13
7
12
10
8
2
0000 000 00000
Service:
3
9
PRODUCT DESCRIPTION
Before using the appliance carefully read Health and Safety guide.
The control panel of this dishwasher activates pushing by ON/OFF button.
For energy saving the control panel deactivates automatically after 10 minutes if no cycle has started.
CONTROL PANEL
DISPLAY - INDICATORS
A. START DELAY
B. ECO CYCLE
C. ZONE WASH - Upper Rack
D. CLOSED WATER TAP
E. ADD SALT
F. ZONE WASH - Lower Rack
G. ADD RINSE AID
H. TABLET
A B
H G F
D
E
C
EN
3
After connecting the appliance to the power supply for the rst time,
the display will guide you to set up the appliance for rst use.
1. The language selection
To select preferred language please
press button „<” or „>”.
Conrm by pressing „OK” button.
After language conrmation, the appliance will go through the rst
time use conguration menu.
2. Setting the water hardness
The water hardness is by default
set to level 3. To change water
hardness level press button „<” or „>”
repeatedly.
To conrm your choice press „OK”
button. The level must be set
according to the table below.
To allow the water softener to work in a perfect way, it is essential that
the water hardness setting is based on the actual water hardness in your
house. This information can be obtained from your local water supplier.
3. Filling the water softener
When water hardness is set, it is
required to ll water softener with
water and special regeneration salt.
Remove the lower rack and unscrew
the reservoir cap (anticlockwise)
As a rst step it is needed to ll
reservoir with water ( ~1.5 litres).
Once done, proceed to the next
step by pressing „OK” button.
Position the funnel (see gure) and ll the salt reservoir right up to its
edge (approximately 1 kg); it is not unusual for some water will spill out.
Remove the funnel and wipe any salt residue away from the opening.
Make sure the cap is screwed on tightly, so that no detergent can get
into the container during the wash program (this could damage the
water softener beyond repair).
Once done, proceed to the next step by pressing „OK” button.
Only use salt that has been specically designed for dishwashers.
4. Setting the brightness level
The brightness level is by default set
to level 5. To change brightness level
press button „<” or „>” repeatedly.
To conrm your choice press „OK”
button.
5. Detergent type operation
In this step it is very important to
choose what type of detergent will
be used (tablet/capsule or
gel/powder).
If you prefer to use All-in-one
detergent in tablet or capsule for
washing - press „OK”, then go to
step 7. Open tap operation on the
next page.
The symbol on display will be lit. If you prefer to use gel
or powder detergent for washing, press „<” or „>”, then go to step
6. Rinse aid operation.
6. Rinse aid operation*
*If All-in-one detergent was chosen in the previous step, this step will
be skipped by the appliance.
Water Hardness Table
Level German
degrees °dH
French
degrees °fH
1 Soft 0 - 6 0 - 10
2 Medium 7 - 11 11 - 20
3 Average 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 Very hard 35 - 50 61 - 90
FIRST TIME USE
Whenever you need to add salt, it is mandatory to complete the
procedure before the beginning of the washing cycle.
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
If the salt container is not lled, the water softener and the
heating element may be damaged as a result.
M
A
X
A
B
35
25
WATER HARDNESS = 3
<> = CHANGE OK = YES
WATER HARDNESS
(1=MIN, 5=MAX)
LANGUAGE: ENGLISH?
<> = CHANGE OK = YES
ENGLISH
SELECTED
POUR WATER
INSERT 1,5 LITER OF
OK = DONE
WATER IN THE
OK = DONE
WATER SOFTENER
OK = DONE
INSERT SALT
ADD 1KG OF SALT
OK = DONE
IN THE SALT DISPENSER
OK = DONE
RINSE AID
INSERT RINSE AID
OK = DONE
IN THE DISPENSER
OK = DONE
ADJUST BRIGHTNESS
(1=MIN, 5=MAX)
BRIGHTNESS = 5
<> = CHANGE OK = YES
DETERGENT TYPE
DO YOU USE
<> = NO OK = YES
DETERGENT?
<> = NO OK = YES
“ALL IN ONE”
<> = NO OK = YES
4
EN
1. Open the dispenser B by pressing and pulling up the tab on the lid.
2. Carefully introduce the rinse aid as far as the maximum (110 ml) re-
ference notch of the lling space A - avoid spilling it. If this happens,
clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
4. Conrm operation by pressing „OK” button.
NEVER pour the rinse aid directly into the tub.
Setting rinse aid level
(not necessary when using tablets/capsules)
The rinse aid dosage can be adjusted to the detergent used. The lower
the setting, the less rinse aid is dispensed. The factory setting is for (5)
level.
To change, follow instructions in section “SETTINGS / MENU”.
7. Open tap operation
Check water tap is open. If closed, open it then conrm by pressing
„OK” button.
8. First cycle operation
Before normal use of appliance it is
recommended to run Intensive cyc-
le rst, to calibrate the appliance.
Insert a detergent into dispenser
chamber B (see below), then press
„OK” button.
Intensive cycle will be selected
automaticly. Press „START/PAUSE”
button.
This rst cycle can be up to 20
minutes longer as a result of the
automatic calibration process.
After this process the appliance is ready for normal use.
ADDING A DETERGENT
To achieve the best washing and drying results, the combined use of
detergent, rinse aid liquid and rened salt is required.
We recommend using detergents that do not contain phosphates or
chlorine, as these products are harmful to the environment.
Good washing results also depend on the correct amount of deter-
gent being used.
Exceeding the stated amount does not result in a more eective wash
and increases environmental pollution.
The amount can be adjusted to the soil level. In the case of normally
soiled items, use approximately either 35g (powder detergent) or
35ml (liquid detergent) and additional tea spoon of detergent directly
inside the tub. If tablets are used, one tablet will be enough.
If the crockery is only lightly soiled or if it has been rinsed with water
before being placed in the dishwasher, reduce the amount of deter-
gent used accordingly (minimum 25 g/ml) e.g. skip the powder/gel
putted inside the tub.
To open the detergent dispenser,
press button A. Introduce the deter-
gent into the dry dispenser B only.
Place the amount of detergent for
pre-washing directly inside the tub.
1. When measuring out the deter-
gent refer to the mentioned ear-
lier information to add the proper
quantity. Inside the dispenser B
there are indications to help the
detergent dosing.
2. Remove detergent residues from the edges of the dispenser and
close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until the
closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program.
If you are using a All-in-one detergents, we recommend that you add
salt in any case, especially if the water is hard or very hard (follow the
instructions given on the packaging).
A
B
Only use detergent which has been specically designed for
dishwashers.
OPEN TAP
OPEN THE
OK = DONE
WATER TAP
OK = DONE
FIRST CYCLE
REMEMBER TO RUN THE
OK = EXIT
INTENSIVE CYCLE
OK = EXIT
WITH EMPTY BASKETS
OK = EXIT
TO COMPLETE
OK = EXIT
THE FIRST SET UP
OK = EXIT
EN
5
ADVICE AND TIPS
TIPS
Before loading the baskets, remove all food residues from the crockery
and empty the glasses. You do not need to rinse beforehand under
running water.
Arrange the crockery so that it is held in place rmly and does not tip
over; and arrange the containers with the openings facing downwards
and the concave/convex parts placed obliquely, thus allowing the
water to reach every surface and ow freely.
Warning: lids, handles, trays and frying pans do not prevent the spray-
er arms from rotating.
Place any small items in the cutlery basket.
Very soiled dishes and pans should be placed in the lower basket
because in this sector the water sprays are stronger and allow a higher
washing performance.
After loading the appliance, make sure that the sprayer arms can
cotate freely.
HYGIENE
To avoid odour and sediment which can be accumulated in the dish-
washer please run a high temperature program at least once a month.
Use a tea spoon of detergent and run it without the loading to clean
your appliance.
UNSUITABLE CROCKERY
• Wooden crockery and cutlery.
• Delicate decorated glasses, artistic handicraft and antique crockery.
Their decorations are not resistant.
• Parts in synthetic material which do not withstand high temperatures.
• Copper and tin crockery.
• Crockery soiled with ash, wax, lubricating grease or ink.
The colours of glass decorations and aluminium/silver pieces can
change and fade during the washing process. Some types of glass (e.g.
crystal objects) can become opaque after a number of wash cycles
too.
DAMAGE TO GLASS AND CROCKERY
• Only use glasses and porcelain guaranteed by the manufacturer as
dishwasher safe.
• Use a delicate detergent suitable for crockery
• Collect glasses and cutlery from the dishwasher as soon as the wash
cycle is over.
UPPER RACK
Load delicate and light dishe-
s:glasses, cups, saucers, low salad
bowls.
The upper rack has tip-up
supports which can be used in a
vertical position when arranging
tea/ dessert saucers or in a lower
position to load bowls and food
containers.
(loading example for the upper rack)
FOLDABLE FLAPS WITH ADJUSTABLE POSITION
The side foldable aps can be positioned at
three dierent heights to optimize the arrange-
ment of crockery inside the rack.
Wine glasses can be placed safely in the foldable
aps by inserting the stem of each glass into the
corresponding slots.
For optimum drying results incline the foldable
aps more. To change the inclination, pull up
the foldable ap, slide it slightly and position it
as you wish.
ADJUSTING THE HEIGHT OF THE UPPER RACK
The height of the upper rack can be adju-
sted: high position to place bulky crockery in
the lower basket and low position to make
the most of the tip-up supports by creating
more space upwards and avoid collision
with the items loaded into lower rack.
The upper rack is equipped with a Upper
Rack height adjuster (see gure), witho-
ut pressing the levers, lift it up by simply
holding the rack sides, as soon as the rack is
stable in its upper position.
To restore to the lower position, press the
levers A at the sides of the rack and move the basket downwards.
We strongly recommend that you do not adjust the height of the
rack when it is loaded.
NEVER raise or lower the basket on one side only.
LOADING THE RACKS
SLIDING TRAY
The upper rack is tted with a sliding tray which can be used to hold
small crockery and cutlery. For optimum washing performance, avoid
positioning bulky crockery directly below the tray.
The tray is removable.
Knives and other utensils with sharp edges must be positioned
with the blades facing downwards.
6
EN
LOWER RACK
For pots, lids, plates, salad bowls, cutlery etc. Large plates and lids
should ideally be placed at the sides to avoid interferences with the
spray arm.
The lower rack has tip-up supports which can be used in a vertical
position when arranging plates or in a horizontal position (lower) to
load pans and salad bowls easily.
The lower rack has a Space Zone (A), a special pull-out support in the
rear of the rack that can be used to support frying pans or baking pans
in upright position, thus taking up less space.
In order to use it, just get hold of the coloured grip and pull it upwards
(B) while rotating it forward. The supports can slide right and left to t
the size of the crockery. (loading example for the upper rack)
A
B
CUTLERY BASKET
The modular basket can slide to optimise the space inside the lower
rack. It is equipped with top grilles for improved cutlery arrangement.
Knives and other utensils with sharp edges must be placed in the
cutlery basket with the points facing downwards or they must be
positioned horizontally in the tip-up compartments on the upper
rack.
Zone Wash 3D uses additional water jets located both: in the lower
and upper part of the dishwasher (marked with orange color) to wash
more intensively heavily soiled items by increasing water coverage on
dishes.
Example: Load pots and casseroles facing lower part of Zone Wash 3D
components and activate the 3D Zone Wash option on the panel.
GLASS CARE
Dedicated accessory that allows you to safely store dierent types of
stem glasses in the lower rack. It enables cleaning & drying results by
allowing an optimised and stable positioning of the glasses.
23
1
1
3
2
A
B
ZONE WASH 3D
EN
7
SELECTING A CYCLE AND OPTIONS
POWER
CLEAN
50°3:10h
EXTRA
DRY
50°3:10h
MODIFYING A RUNNING PROGRAM
If a wrong program was selected, it is possible to change it, provided
that it has only just begun: press and hold the „ON/OFF” button,
the machine will switch o.
Switch the machine back on using the „ON/OFF” button and
select the new wash cycle and any desired options; start the cycle by
pressing the „START/PAUSE” button.
TO PAUSE THE CYCLE (ADDING EXTRA ITEMS)
Open the door and place the crockery inside the dishwasher,
(beware of HOT steam!). Close the door and press „START/PAUSE”
button to resume the cycle from the point at which it was
interrupted.
ACCIDENTAL INTERRUPTIONS
If the door is opened during the wash cycle, or if there is a power
cut, the cycle stops. To resume the cycle from where it was interrup-
ted, close the door and press the „START/PAUSE” button.
Open appliance door (beware of hot steam!) and unload the racks,
starting from the lower rack rst.
If it is needed to rell salt reservoir or rinse aid dispenser, it is
recommended to do this operations right before start of the next
cycle.
ECO CYCLE
1 2 3
45
The list of available cycles and options can be found in Cycle Table
on next page. Eco cycle is selected by default. If you want to have Last
Used cycle selected by default, you can change it in „Settings Menu”.
It is possible to select a cycle by pressing 1 of 6 cycles direct access
buttons or by pressing „Extra Cycles” button repeatedly. When the
last one is reached a further press goes back to the rst.
Press cycle button to choose cycle in accordance with the level
of soiling of the dishes and with Cycle Table. Information will be
shown on the display:
1. Indicators
2. Name of the selected cycle
3. Vertical bar showing the position of the extra cycle list only
4. Energy consumption of the selected cycle
5. Water consumption of the selected cycle
Three seconds after selecting a cycle, its
time and temperature will be displayed
(if available).
Press „INFO” button to display a brief description of the cycle and
its water / energy consumption.
During the selection phase the „START/PAUSE” LED blinks.
Additional options are available for most cycles (see „Options and
Settings” section). When any option is selected, its name is shown on
the display on the right.
If more than one option is selected one
bullet point for each option is displayed.
Each option name is displayed for 3 sec.
with its bullet point fulled.
When the cycle and option selection is complete, press „START/PAUSE”
button and close the door to start chosen cycle.
During the cycle, the progress is shown on the display (as bar) as well
as phase of cycle, and time to the end of the cycle with “:” blinking:
Depending at the selected cycle, the display may provide additional
information:
• PRE-WASH - extra items can be added.
• WASHING - main washing.
• DRYING - drying phase of cycle.
After the cycle nishes, there is an acustic signal and the dispaly
shows:
On the display additional information can be shown:
• ADD SALT - rell salt reservoir.
• ADD RINSE AID - rell rinse aid.
• WPRO - every 50 cycle, will be recommended to use the WPRO
cleaner (according to instruction on the consumable).
After 10 minutes the appliance switches o.
CYCLE FINISHED
WASHING
1:20h
NORMALLY SOILED CROCKERY.
STANDARD PROGRAM,
WATER ENERGY
8
EN
CYCLES TABLE
CYCLE Available options *
Detergent
dispenser Duration of
wash cycle
(h:min)**
Water
consump-
tion (l/cycle)
Energy
cosumption
(kWh/cycle)
Drying
phase
ActivEco
BTUB
ECO
50° EXTRA DRY, TABLET, START DELAY 3:10 9.5 0.93
AUTO-INTENSIVE
65 °
3D ZONE WASH, ZONE WASH, TURBO,
EXTRA DRY, TABLET, START DELAY - 2:00 - 3:10 14.0 - 17.0 1.50 - 1.85 -
AUTO-NORMAL
55°
3D ZONE WASH, ZONE WASH, TURBO,
EXTRA DRY, TABLET, START DELAY 1:30 - 2:30 14.5 - 16.0 1.15 - 1.30
AUTO-FAST
50° TABLET, START DELAY - 0:55 - 1:20 13.0 - 14.5 1.15 - 1.25 - -
DELICATES
45°
ZONE WASH, EXTRA DRY, TABLET,
START DELAY - 1:40 11.5 1.20 -
EXPRESS 30’
50° ZONE WASH, TABLET, START DELAY - 0:30 9.0 0.55 - -
EXTRA CYCLES - available by pressing button
GOOD NIGHT 50° EXTRA DRY, TABLET, START DELAY - 3:30 15.0 1.15 -
SANITIZING 65° START DELAY - 1:40 10.0 1.30 -
SOAK cold ZONE WASH, START DELAY - - 0:12 4.5 0.01 - -
SELF CLEAN 65° START DELAY - - 0:50 8.0 0.85 - -
1. ECO - Normally soiled crockery. Standard program, the most ecient in terms of its combined energy and water consumption.
2. AUTO-INTENSIVE - Automatic program for heavily soiled dishes and pans (not to be used for delicate items).
3. AUTO-NORMAL - Automatic program for normally soiled pans and dishes.
4. AUTO-FAST - Automatic program for limited quantity of normally soiled crockery. Ensures optimal cleaning performance in shorter time.
5. DELICATES - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
6. EXPRESS 30’ - Program to be used for lightly-soiled dishes with no dried food residues.
EXTRA CYCLES
7. GOOD NIGHT - Suitable for night-time operation of the appliance. Optimum performance ensured.
8. SANITIZING - Normally or heavily soiled crockery, with additional antibacterial wash.
9. SOAK - Crockery to be washed later. No detergent to be used with this program.
10. SELF CLEAN - Program to be used to perform maintenance of the dishwasher. It cleans the interior of the appliance using hot water.
Notes:
To reduce consumption even further, only run the dishwasher when it is full.
Please note that cycles like Express or Auto Fast are most eective for lightly soiled dishes.
ECO program data is measured under laboratory conditions according to European Standard EN 50242. Note for Test Laboratories: For information on
comparative EN testing conditions, please send an email to the following address: assistenza_en_lvs@indesitcompany.com
Pre-treatment of the dishes is not needed before any of the programs.
* Not all options can be used simultaneously.
** The duration of the program shown on the display or in the booklet is an estimate calculated on standard conditions. The actual time may vary
depending on many factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration. The sensor calibration can increase program duration up to 20 min.
Standby consumption: Left-on mode consumption: 6 W - O mode consumption: 0.5 W
EN
9
OPTIONS AND SETTINGS
This setting allows you to optimise the performance of the cycle
according to the type of detergent used. Enable it if you use combined
detergents in tablet form (rinse aid, salt and detergent in 1 dose).
To set the Tablet, enter in the setting
menu by pressing „OK” button and
navigate with „< , >” until „TABLET”
is shown, then press „OK” button.
If there are not many dishes to be washed it can be loaded in one rack
only. Using this option you can select which rack you want to wash.
Select a compatible cycle (see “Cycles table”), and then press the
ZONE WASH button: the symbol of the chosen rack will appear on the
display.
By default the ZONE WASH is not active and all racks icons are lit.
Selected only lower rack.
Selected only upper rack.
Thanks to the additional 3D water jets placed on the bottom of the
cavity, 3D ZONE WASH option allows to save energy or to increase the
washing performance of the dishwasher. It is compatible with Normal
and Intensive cycles, and it works with one rack at once.
• 3D ZONE WASH + NORMAL CYCLE: it allows to reduce energy
consumption up to 40%.
• 3D ZONE WASH + INTENSIVE CYCLE: it increases the washing
performances up to 40%. Ideal for very soiled mixed loads, e.g. pans
and saucepans, dishes with heavy encrustation or dicult-to-clean
crockery (grater, vegetable mill, dirty cutlery).
How to activate the option:
1. Select a compatible cycle (Normal or Intensive).
2. Press button to activate/deactive the option: a basket icon will
blink for a few seconds.
3. It is possible to change the selected rack pressing the ZONE WASH
button.
4. Remember to load the crockery in the selected rack only.
The start of the cycle may be delayed for a selected period of time.
To set a delay, enter in the setting menu by pressing „OK” button and na-
vigate with „< , >” until „START DELAY” is shown, then press „OK” button.
With each press of the button “>” or “<“, the delay start increases by:
• every 0:30 if selection below 4 hours,
• every 1:00 if selection is below 12 hours,
• every 2 hours if selection is above 12 hours.
To remove the delay, press „<” or
„>” button until „OFF” is displayed.
Default value is OFF.
If delay is selected, the is lit.
Once „OK” button is pressed the
delay is conrmed and the machine
comes back to the cycle selection
screen with delay value visible.
Close the door and press „START” to start the delay.
This option can be used to reduce the duration of the main cycles
while maintaining washing and drying performance levels.
To set the Turbo, enter in the setting
menu by pressing „OK” button and
navigate with „< , >” until „TURBO” is
shown, then press „OK” button.
With each press of the button „>” or
„<“ option will be ON or OFF.
Conrm by pressing „OK” button.
The KEYLOCK function blocks the
control panel except the „ON/OFF”
button.
To activate the Keylock, enter in the
setting menu by pressing „OK” button
and navigate with „< or >” until
„KEYLOCK” is shown, then press OK.
Once set, to deactivate it keep pressing „OK” button for a few seconds.
This option allows to improve the drying of the dishes using higher
temperature during the nal rinse and an extended drying phase. The
EXTRA DRY option results in the lengthening of the wash cycle.
To set the Extra Dry, enter in the
setting menu by pressing „OK” button
and navigate with „< , >” until
„EXTRA DRY” is shown, then press
„OK” button.
With each press of the button „>” or
„<“ option will be ON or OFF.
Conrm by pressing „OK” button.
TABLET (All-in-one)
TABLET OFF
TABLET ON
TABLET ON
ZONE WASH
3D ZONE WASH
3D WASH
DEACTIVATED
3D WASH
ACTIVATED
START DELAY
START DELAY OFF
<STARTS IN h> OFF
<STARTS IN h> 4:00
<STARTS IN h> 4:00
TURBO
TURBO OFF
TURBO ON
TURBO ON
KEYLOCK ACTIVATED
PRESS "OK” FOR 3 SEC.
KEYLOCK
KEEP PRESSED…
KEYLOCK DEACTIVATED
EXTRA DRY
EXTRA DRY OFF
EXTRA DRY ON
EXTRA DRY ON
With each cycle additional options can be used. A full list of available options working with specic cycles can be found in the Cycle Table on
the previous page. All active options are shown on the display.
To set an option press „OK” button. SET OPTIONS message is shown for a few seconds. Then use „<” or „>” button to navigate through the
option list. Press „OK” to select the option, in the setting menu the LED above „OK” button is lit.
If the option is not available, it will be still visible in its position but with „ ”
10
EN
SETTINGS MENU
Language
To change language, enter in the
setting menu by pressing „OK”
button and navigate with „< , >”
until „LANGUAGE” is shown, then
press „OK” button.
First cycle
You can choose which cycle is
selected by default when switching
on the appliance: ECO or the LAST
USED one.
To change rst cycle, enter in the
setting menu by pressing „OK” but-
ton and navigate with „< , >” until
„FIRST CYCLE” is shown, then press
„OK” button.
To change sounds, enter in the
setting menu by pressing „OK”
button and navigate with „< , >”
until „SOUNDS” is shown, then press
„OK” button.
Choose between 2 levels: High;
Low. Can be also OFF.
Water Hardness
To change water hardness level,
enter in the setting menu by
pressing „OK” button and navigate
with „< , >” until „WATER HARDNESS”
is shown, then press „OK” button.
To setup correct level according to water hardness, see table on page 3.
Screen Brightness
To change screen brightness
level, enter in the setting menu by
pressing „OK” button and navigate
with „< , >” until „SCREEN BRIGHT.” is
shown, then press „OK” button.
Choose between ve levels: 1, 2, 3, 4 and 5.
ActivEco is a convection drying system which automatically opens the
door during/after drying phase to ensure exceptional drying perfor-
mance every day. Door opens at the temperature that is safe to your
kitchen furniture, thus door will not be opened when the option of
SANI RINSE or TURBO are on.
As additional steam protection, special designed protection foil is added
together with the dishwasher (depending on the model type - can be
the need to buy it). To see how to mount protection foil please refer to
(INSTALLATION GUIDE).
ActivEco functionality could be disabled by the user as follows:
To set ActivEco on or o, enter in the
setting menu by pressing „OK”
button and navigate with „< , >”
until „ACTIVECO” is shown, then
press „OK” button.
Rinse Aid level
To change rinse aid level, enter in
the setting menu by pressing „OK”
button and navigate with „< , >”
until „RINSE AID LEV.” is shown, then
press „OK” button.
Choose between ve levels: 1, 2, 3, 4 and 5.
If the rinse aid level is set to 1, no rinse aid will be supplied. The LOW
RINSE AID indicator light will not be lit if you run out of rinse aid.
The factory setting is for (5) level .
• If you see bluish streaks on the dishes, set a low number (2-3).
• If there are drops of water or limescale marks on the dishes, set
a high number (4-5).
Demo mode
To see the demo mode, enter in the
setting menu by pressing „OK”
button and navigate with „< , >”
until „DEMO MODE” is shown, then
press „OK” button.
Reset to factory default
To reset to factory default, enter in
the setting menu by pressing „OK”
button and navigate with „< , >”
until „RESET TO DEF.” is shown, then
press „OK” button.
Exit
To exit the setting menu, press any
cycle button or press „< , >” button
untill EXIT is shown, then press
„OK” button.
ActivEco
6.ACTIVECO ON
6.ACTIVECO OFF
6.TUB LIGHT OFF
7.RINSE AID LEV. 5
7.RINSE AID LEV. 4
8.DEMO MODE ON
8.DEMO MODE OFF
9.RESET TO DEF. ON
9.RESET TO DEF. OFF
10.EXIT OK
To change machne settings you need to enter into the Settins Menu.
Press „OK” button and navigate with „< , >” until SETTINGS is shown, then press „OK” button.
To exit the setting menu, press any cycle button or press „< , >” button untill EXIT is shown, then press „OK” button.
4.WATER HARDNESS 3
4.WATER HARDNESS 4
5.SCREEN BRIGHT. 5
5.SCREEN BRIGHT. 3
1.LANGUAGE SET
1.ITALIAN
1.ENGLISH < >
2.FIRST CYCLE SET
2.<LAST USED>
2.<ECO> < >
3.SOUNDS SET
3.<OFF>
3.<HIGH> < >
Sounds
EN
11
CARE AND MAINTENANCE
ATTENTION: Always unplug the appliance when cleaning it and when
performing maintenance work.Do not use ammable liquids to clean
the machine.
CLEANING THE DISHWASHER
Any marks on the inside of the appliance may be
removed using a cloth dampened with water and a
little vinegar.
The external surfaces of the machine and the control
panel can be cleaned using a non-abrasive cloth
which has been dampened with water. Do not use
solvents or abrasive products.
PREVENTING UNPLEASANT ODOURS
Always keep the door of the appliance ajar in order to avoid moisture
from forming and being trapped inside the machine.
Clean the seals around the door and detergent dispensers regularly
using a damp sponge. This will avoid food becoming trapped in the se-
als, which is the main cause behind the formation of unpleasant odours.
CHEKING THE WATER SUPPLY HOSE
Check the inlet hose regularly for brittleness and cracks. If damaged,
replace it by a new hose available through our After-Sales Service or
your specialist dealer. Depending on the hose type:
If the inlet hose has a transparent coating, periodically check if the
colour intensies locally. If yes, the hose may have a leak and should
be replaced.
For water stop hoses: check the small safety valve inspection window
(see arrow). If it is red, the water stop function was triggered, and the
hose must be replaced by a new one.
For unscrewing this hose, press the release button while unscrewing
the hose.
CLEANING THE WATER INLET HOSE
If the water hoses are new or have not been used for an extended
period of time, let the water run to make sure it is clear and free of im-
purities before performing the necessary connections. If this precau-
tion is not taken, the water inlet could become blocked and damage
the dishwasher.
CLEANING THE FILTER ASSEMBLY
Regularly clean the lter assembly so that the lters do not clog and
that the waste water ows away correctly.
The lter assembly consists of three lters which remove food residues
from the washing water and then recirculate the water: to obtain the
best washing results, you need to keep them clean.
The dishwasher must not be used without lters or if the lter is
loose.
After several washes, check the lter assembly and if necessary clean
it thoroughly under running water, using a non-metallic brush and
following the instructions below:
1. Turn the cylindrical lter A in an anti-clockwise direction and pull it
out (Fig 1).
2. Remove the cup lter B by exerting a slight pressure on the side
aps (Fig 2).
3. Slide out the stainless-steel plate lter C (Fig 3).
4. Inspect the trap and remove any food residues. NEVER REMOVE
the wash-cycle pump protection (black detail) (Fig 4).
After cleaning the lters, re-place the lter assembly and x it in posi-
tion correctly; this is essential for maintaining the ecient operation
of the dishwasher.
CLEANING THE SPRAY ARMS
On occasions, food residue may
become encrusted onto the spray
arms and block the holes used
to spray the water. It is therefore
recommended that you check the
arms from time to time and clean
them with a small non-metallic
brush.
To remove the upper spray arm,
turn the plastic locking ring in an
anti-clockwise direction. The upper
spray arm should be replaced so
that the side with the greater num-
ber of holes is facing upwards.
The lower spray arm may be remo-
ved by pulling it upwards.
A
A
B
C
21
43
12
EN
INSTALLATION
ATTENTION: If the appliance must be moved at any time, keep it in an
upright position; if absolutely necessary, it may be tilted onto its back.
CONNECTING THE WATER SUPPLY
Adaptation of the water supply for installation should only be perfor-
med by a qualied technician.
The water inlet and outlet hoses may be positioned towards the right
or the left in order to achieve the best possible installation.
Make sure the dishwasher does not bend or squash the hoses.
CONNECTING THE WATER INLET HOSE
• Run the water until it is perfectly clear.
• Screw the inlet hose tightly into position and turn on the tap.
If the inlet hose is not long enough, contact a specialist store or an
authorised technician.
The water pressure must be within the values indicated in the Techni-
cal Data table - otherwise the dishwasher may be function properly.
Make sure the hose is not bent or compressed.
SPECIFICATIONS FOR THE CONNECTION OF THE WATER SUPPLY HOSE:
CONNECTING THE WATER OUTLET HOSE
Connect the outlet hose to a drain duct with a minimum diameter of
2 cm A.
The outlet hose connection must be at a height ranging from 40 to
80 cm from the oor or surface where the dishwasher rests.
Before connecting the water outlet hose to the sink drain, remove the
plastic plug B.
ANTI-FLOODING PROTECTION
Anti-ooding protection. To ensure oods do not occur, the dishwasher:
- is provided with a special system which blocks the water supply in
the event of anomalies or leaks from inside the appliance.
Some models are also equipped with the supplementary safety device
New Aqua Stop, which guarantees anti-ooding protection even in
the event of a supply hose rupture.
Under no circumstances should the water inlet hose be cut as it conta-
ins live electrical parts.
ELECTRICAL CONNECTION
WARNING: Under no circumstances should the water inlet hose
be cut as it contains live electrical parts.
Before inserting the plug into the electrical socket, make sure that:
• The socket is earth and complies with current regulations;
• The socket can withstand the maximum load of the appliance as
shown on the data plate located on the inside of the door (see
PRODUCT DESCRIPTION).
• The power supply voltage falls within the values indicated on the
data plate on the inside of the door.
• The socket is compatible with the plug of the appliance.
If this is not the case, ask an authorised technician to replace the plug
(see AFTER-SALES SERVICE). Do not use extension cables or multiple
sockets. Once the appliance has been installed, the power supply
cable and the electrical socket should be easily accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, have it replaced by the ma-
nufacturer or its authorised Technical Assistance Service in order to
prevent all potential hazards.
The Company shall not be held responsible for any incidents, if these
regulations are not observed.
POSITIONING AND LEVELLING
1. Position the dishwasher on a level sturdy oor. If the oor is uneven,
the front feet of the appliance may be adjusted until it reaches
a horizontal position. If the appliance is levelled correctly, it will be
more stable and much less likely to move or cause vibrations and
noise while it is operating.
2. Before recessing the dishwasher, stick the adhesive transparent strip
under the wooden shelf in order to protect it from any condensation
which may form.
3. Place the dishwasher so that its sides or back panel are in contact
with the adjacent cabinets or the wall. This appliance can also be
recessed under a single worktop.
4. To adjust the height of the rear foot, turn the red hexagonal bushing
on the lower central part at the front of the dishwasher using a
hexagonal spanner with an opening of 8 mm. Turn the spanner in
a clockwise direction to increase the height and in an anticlockwise
direction to decrease it.
DIMENSIONS AND CAPACITY:
MIN 40 cm
MAX 80 cm
WATER SUPPLY cold or hot (max. 60°C)
WATER INTAKE 3/4”
POWER OF WATER PRESSURE 0,05 ÷ 1 MPa (0.5 ÷ 10 bar)
7,25 – 145 psi
WIDTH 600 mm
HEIGHT 850 mm
DEPTH 600 mm
CAPACITY 14 standard place-settings
EN
13
TROUBLESHOOTING
Your dishwasher may not work properly.
Before contacting the After-sales Service, check if the problem can be solved by going through the following list.
PROBLEMS POSSIBLE CAUSES SOLUTIONS
Display shows:
CHECK SALT or
ADD SALT
Salt reservoir is empty. Rell reservoir with salt (see page 2).
Adjust water hardness (see page 2).
Display shows:
CHECK RINSE AID or
ADD RINSE AID
Rinse aid dispenser is empty. Rell dispenser with rinse aid (see page 2).
... is not working / will not
start.
The appliance must be switched on.Check the household circuit fuse if there is no power supply.
The appliance door doesn’t close. Check if the appliance door is closed.
“Start Delay” option is ON.
Check whether the „Start Delay” option has been selected. If it has, the
appliance will start once the set time has elapsed. If necessary, r eset
the current cycle by switching OFF the dishwasher, then switch it on
again, select a new cycle, press START and close the door.
Display shows: F6
symbol on the display
indicators
Water pressure is too low. The water tap must be fully open during water inlet (minimum capaci-
ty: 0.5 litres per minute).
Kinked water inlet hose or cloged
inlet lters.
The water inlet hose must not be kinked and the inlet lter in the water
tap connector must not be dirty or clogged.
Display shows: F3
Dirty lters. Clean the lters.
Kinked drain hose. The drain hose must not be kinked.
Syphon hose connection closed. The closure disk of the syphon hose connection
must be removed.
Display shows: F2
Dirty lters or spray arms. Clean lters and spray arms.
Too little water in the appliance
system.
Concave items (e.g. bowls, cups) must be arranged
facing downwards in the rack.
Drain hose incorrectly tted.
The drain hose must be tted correctly (for high mounted
appliances, leave min. 200 - 400mm from the lower edge of the
appliance) - see Installation.
High level of foam inside. Repeat without detergent or wait until foam
disappears..
Water pressure is too low. The water tap must be fully open during water inlet (minimum capaci-
ty: 0.5 litres per minute).
Kinked water inlet hose or cloged
inlet lters.
The water inlet hose must not be kinked and the inlet lter in the water
tap connector must not be dirty or clogged.
Display shows:
PRESS START AND
CLOSE THE DOOR
Door is not closed within
4 seconds of button press. Press again and close the appliance door within 4 seconds.
Display shows:
OPEN AND CLOSE
THE DOOR
The door was not open betwe-
en cycles.
Unload appliance (if not unloaded before), open and close the
door.
Display shows: Fx Appliance has technical defect. Call customer service (state fault displayed).
Close the water tap.
14
EN
PROBLEMS POSSIBLE CAUSES SOLUTIONS
The door doesn’t
lock.
Racks are not t to the end. Verify that racks are t to the end.
The door is not lock. Vigorously push the door until you hear the “clack” sound.
The dishwasher
makes excessive
noise.
The dishes are rattling against each. Arrange the crockery correctly (see Loading the Racks).
An excessive amount of foam has been
produced.
The detergent has not been measured out correctly or it is not suitable for
use in dishwashers (see Filling the Detergent Dispenser). Reset the current
cycle by switching OFF the dishwasher, then switch it on again, select
a new program, press START and close the door. Please do not add any
detergent.
The dishes have not
been dried.
The selected program hasn’t any drying
phase. Verify on the programs table if the selected program has the drying phase.
The rinse aid has run out or the resolution
is not adequate.
Add the rinse aid or adjust the dosage levels higher (see Filling the Rinse
Aid Dispenser).
The dishes are made of non-stick or
plastic. It is normal the presence of drops of water (see Tips).
The dishes are not
clean.
The crockery has not been arranged
properly. Arrange the crockery correctly (see Loading the Racks).
The spray arms cannot rotate freely, being
hindered by the dishes. Arrange the crockery correctly (see Loading the Racks).
The wash cycle is too gentle and/or deter-
gent eciency is low. Select an appropriate wash cycle (see Programs Table).
An excessive amount of foam has been
produced (see AFTER-SALES SERVICE).
The detergent has not been measured out correctly or it is not suitable for
use in dishwashers (see Filling the Detergent Dispenser). Reset the current
cycle by switching OFF the dishwasher, then switch it on again, select
a new program, press START and close the door. Please do not add any
detergent.
The cap on the rinse aid compartment has
not been shut correctly. Make sure the cap of the rinse aid dispenser is closed.
The lter is soiled or clogged. Clean the lter assembly (see Care and Maintenance).
There is no salt. Fill the salt reservoir (see Filling the Salt Reservoir).
The dishes and glas-
ses show calcination
or a whitish lm.
The salt level is too low. Fill the salt reservoir (see Filling the Salt Reservoir).
The adjustment of the water hardness is
not adequate. Increase the values (see Water Hardness Table).
The cap of the salt reservoir is not proper-
ly closed. Check to have properly closed the salt reservoir cap.
The rinse aid is used up or the dosage is
insucient. Add the rinse aid or adjust the dosage levels higher.
The dishes and
glasses are blue
streaked or have a
bluish tinge.
The rinse aid dosage is excessive. Adjust the dosage rates below.
EN
15
16
EN
PRODUCT FISCHE
The technical data containing the energy consumption data can be
downloaded from the website: docs.hotpoint.eu
IEC 436
:
CONTACTING AFTER-SALES SERVICE
You can nd our contact details in the warranty manual.
When contacting our Client After-sales Service,
please state the codes provided on your
product’s rating plate.
400011317993B
03/2018 jk - Xerox Fabriano