Hotpoint TCHL 870 BP.9 (UK) User Manual
Displayed below is the user manual for TCHL 870 BP.9 (UK) by Hotpoint which is a product in the Tumble Dryers category. This manual has pages.
Related Manuals
1
English
GB
TUMBLE DRYER
TCHL 870 (UK)
Instruction booklet
This symbol reminds you to read this in-
struction manual.
! Keep this manual at hand for immediate reference whenever
necessary. Always store this manual close to the tumble dryer and
remember to pass it on to any new owners when selling or tran-
sferring the appliance, so they may familiarise with the warnings
and suggestions herein contained.
! Read these instructions carefully: the following pages contain
important information on installation and useful suggestions for
operating the appliance.
Contents
Installation, 2
Warnings, 3
Care and Maintenance, 5
Control panel, 7
Start and Programmes, 8
Laundry, 10
Troubleshooting, 11
Service, 12
www.hotpoint.eu
2
GB
Where to install the tumble dryer
If the dryer is installed below a worktop,
ensure there are 10
mm between the upper
panel of the dryer and
any objects above it,
and 15 mm between
the sides of the machine
and the walls or furniture
units adjacent to it. This
ensures adequate air
circulation.
The appliance must be installed with the rear
surface placed against a wall.
Ventilation
Make sure that the dryer is installed in a room free of
humidity and with adequate air circulation. The flow of air
around the dryer is essential to allow water to condense
during drying; the dryer will not function properly if it is
placed in an enclosed space or inside a cabinet.
Some condensation may form if the dryer is used in a small
or cold room.
Water drain
If your dryer is installed next to a drain the water can be
plumbed into this drain. This does away with the need to
empty the water container. If the dryer is stacked onto or
installed next to a washing machine it can share the same
drain. The height of the drain must be less than 3’ (1 m) from
the bottom of the dryer.
Remove existing hose from position shown in picture A and fit
a suitable length of hose and connect as shown in picture B.
The drain tube has to be below 1 m from the bottom of
the Dryer
Make sure that the hose is not squashed or kinked
when the dryer is in its final location.
1
2
2
1
Less than 1m
Picture A Picture B
We do not recommend that the dryer is
installed in a cupboard but the dryer must never
be installed behind a lockable door, a sliding
door or a door with a hinge on the opposite
side to that of the dryer door.
Electrical connections
Before plugging the appliance into the socket,
10 mm
15 mm 15 mm
check the following:
Make sure your hands are dry.
The socket must have an earth
connection.
The socket must be able to withstand the
machine’s maximum power output as
indicated on the rating plate.
The power supply voltage must fall within
the values indicated on the data plate.
Do not use extension leads. Do not pull the
power supply cable. Do not use multiple
plug adaptors if the appliance is fitted with a
plug. For appliances with fitted plug, if the
plug is not suitable for you socket outlet,
contact a qualified technician.
The dryer must not be installed outdoors,
even if the space is sheltered.
Once installed, the dryer’s electrical wire
and plug must be within reach.
The power cord must not be bent or
squashed.
If the plug being replaced is a non-rewirable
type, then the cut-off plug must be disposed of
safely. DO NOT leave it where it can be inserted
into a socket and create a shock hazard.
The power must be regularly checked. If
the supply cord is damaged, it must be
replaced by service agent . (see Assistance).
The manufacturer denies any
responsibility should any of these rules
not be followed.
If in doubt about any of the above
consult a qualified electrician.
Preliminary information
Once the tumble dryer is installed, clean the inside of the
drum before operating it and remove any dirt accumulated
during transportation.
Installation
3
GB
Where to install the tumble dryer
If the dryer is installed below a worktop,
ensure there are 10
mm between the upper
panel of the dryer and
any objects above it,
and 15 mm between
the sides of the machine
and the walls or furniture
units adjacent to it. This
ensures adequate air
circulation.
The appliance must be installed with the rear
surface placed against a wall.
Ventilation
Make sure that the dryer is installed in a room free of
humidity and with adequate air circulation. The flow of air
around the dryer is essential to allow water to condense
during drying; the dryer will not function properly if it is
placed in an enclosed space or inside a cabinet.
Some condensation may form if the dryer is used in a small
or cold room.
Water drain
If your dryer is installed next to a drain the water can be
plumbed into this drain. This does away with the need to
empty the water container. If the dryer is stacked onto or
installed next to a washing machine it can share the same
drain. The height of the drain must be less than 3’ (1 m) from
the bottom of the dryer.
Remove existing hose from position shown in picture A and fit
a suitable length of hose and connect as shown in picture B.
The drain tube has to be below 1 m from the bottom of
the Dryer
Make sure that the hose is not squashed or kinked
when the dryer is in its final location.
1
2
2
1
Less than 1m
Picture A Picture B
We do not recommend that the dryer is
installed in a cupboard but the dryer must never
be installed behind a lockable door, a sliding
door or a door with a hinge on the opposite
side to that of the dryer door.
Electrical connections
Before plugging the appliance into the socket,
10 mm
15 mm 15 mm
check the following:
Make sure your hands are dry.
The socket must have an earth
connection.
The socket must be able to withstand the
machine’s maximum power output as
indicated on the rating plate.
The power supply voltage must fall within
the values indicated on the data plate.
Do not use extension leads. Do not pull the
power supply cable. Do not use multiple
plug adaptors if the appliance is fitted with a
plug. For appliances with fitted plug, if the
plug is not suitable for you socket outlet,
contact a qualified technician.
The dryer must not be installed outdoors,
even if the space is sheltered.
Once installed, the dryer’s electrical wire
and plug must be within reach.
The power cord must not be bent or
squashed.
If the plug being replaced is a non-rewirable
type, then the cut-off plug must be disposed of
safely. DO NOT leave it where it can be inserted
into a socket and create a shock hazard.
The power must be regularly checked. If
the supply cord is damaged, it must be
replaced by service agent . (see Assistance).
The manufacturer denies any
responsibility should any of these rules
not be followed.
If in doubt about any of the above
consult a qualified electrician.
Preliminary information
Once the tumble dryer is installed, clean the inside of the
drum before operating it and remove any dirt accumulated
during transportation.
Installation
! This appliance has been designed and built
according to international safety standards.
These warnings are given for safety reasons
and must be followed carefully.
General safety
• This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved.
• This tumble dryer has been designed for
home, and not professional, use.
• Do not touch the appliance while barefoot
or with wet hands or feet.
• Unplug the machine by pulling on the plug,
not the cord.
• After using the dryer, turn it off and unplug
it. Keep the door closed to make sure that
children do not use it as a toy.
•Children should be supervised to ensure
that they do not play with the dryer.
• Cleaning and user maintenance shall not be
made by children without supervision.
•Children of less than 3 years should be
kept away from the appliance unless
continuously supervised.
• The appliance must be installed correctly
and have proper ventilation. The air intake
at the front of the dryer should never be
obstructed (see Installation).
• Never use the dryer on carpeting where the
pile height would prevent air from entering
the dryer from the base.
• Check to see if the dryer is empty before
loading it.
• The back of the dryer could become
very hot. Never touch it while in use.
• Do not use the dryer unless the filter,
watercontainer and condenser are securely
in place (see Maintenance).
• Do not overload the dryer (see Laundry for
maximum loads).
• Do not load items that are dripping wet.
• Carefully check all instructions on clothing
labels (see Laundry).
• Do not tumble dry large, very bulky items.
• Do not tumble dry acrylic fibres at high
temperatures.
• Do not turn off the dryer when there are
still warm items inside.
• Clean the filter after each use (see
Maintenance).
• Empty the water container after each use
(see Maintenance).
●• Clean the condenser unit at regular intervals
(see Maintenance).
●• Do not allow lint to collect around the
dryer.
• Never climb on top of the dryer. It could
result in damage.
• Always follow electrical standards and
requirements (see Installation).
• Always buy original spare parts and
accessories (see Service).
To minimise the risk of fire
in your tumble dryer, the
following should be observed:
• Tumble dry items only if they have been
washed with detergent and water, rinsed
and been through the spin cycle. It is a fire
hazard to dry items that HAVE NOT been
washed with water.
●• Do not dry garments that have been
treated with chemical products.
• Do not tumble dry items that have
been spotted or soaked with vegetable
or cooking oils, this constitutes a fire
hazard. Oil-affected items can ignite
spontaneously,especially when exposed
to heat sources such as a tumble dryer.
The items become warm, causing
an oxidisation reaction with the oil,
Oxidisation creates heat. If the heat
cannot escape, items can become hot
enough to catch fire. Piling, stacking or
storing oil-effected items can prevent
heat from escaping and so create a fire
hazard.If it is unavoidable that fabrics
containing vegetable or cooking oil or
those that have been contaminated with
hair care products be placed in a tumble
dryer they should first be washed with
extra detergent - this will reduce, but not
eliminate the hazard. They should not
be removed from the dryer and piled or
stacked while hot.
• Do not tumble dry items that have
previously been cleaned in or washed
in, soaked in or soiled with petrol/
gasoline, dry cleaning solvents or other
flammable or explosive substances. Highly
flammable substances commonly used in
domestic environments including cooking
oil, acetone, denatured alcohol, kerosene,
spot removers, turpentine, waxes and wax
removers. Ensure these items have been
washed in hot water with an extra amount
of detergent before being dried in the
tumble dryer.
●• Do not tumble dry items containing foam
rubber (also known as latex foam), or
similarly textured rubber like materials.
Foam rubber materials can, when heated,
produce fire by spontaneous combustion.
●• Fabric softener or similar products should
not be used in a tumble dryer to eliminate
the effects of static electricity unless the
practice is specifically recommended by the
manufacturer of the fabric softener product.
• Do not tumble dry undergarments that
contain metal reinforcements eg. bras
with metal reinforcing wires. Damage to
the tumble dryer can result if the metal
reinforcements come loose during drying.
●• Do not tumble dry rubber, plastic articles
such as shower caps or babies waterproof
covers, polythene or paper.
• Do not tumble dry rubber backed articles,
clothes fitted with foam rubber pads,
pillows, galoshes and rubber coated tennis
shoes.
• Remove all objects from pockets such as
lighters and matches.
! WARNING: Never stop the dryer before
the end of the drying cycle unless all
items are quickly removed and spread
out so that the heat is dissipated.
Save energy and respect the
environment
• Wring out all items to eliminate excess water
before tumble drying (if you use a washing
machine first, select a high spin cycle). Doing
this will save time and energy during drying.
• Always dry full loads - you save energy: single
items or small loads take longer to dry.
• Clean the filter after each use to contain energy
consumption costs (see Maintenance).
Warnings
4
GB
! This appliance has been designed and built
according to international safety standards.
These warnings are given for safety reasons
and must be followed carefully.
General safety
• This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved.
• This tumble dryer has been designed for
home, and not professional, use.
• Do not touch the appliance while barefoot
or with wet hands or feet.
• Unplug the machine by pulling on the plug,
not the cord.
• After using the dryer, turn it off and unplug
it. Keep the door closed to make sure that
children do not use it as a toy.
•Children should be supervised to ensure
that they do not play with the dryer.
• Cleaning and user maintenance shall not be
made by children without supervision.
•Children of less than 3 years should be
kept away from the appliance unless
continuously supervised.
• The appliance must be installed correctly
and have proper ventilation. The air intake
at the front of the dryer should never be
obstructed (see Installation).
• Never use the dryer on carpeting where the
pile height would prevent air from entering
the dryer from the base.
• Check to see if the dryer is empty before
loading it.
• The back of the dryer could become
very hot. Never touch it while in use.
• Do not use the dryer unless the filter,
watercontainer and condenser are securely
in place (see Maintenance).
• Do not overload the dryer (see Laundry for
maximum loads).
• Do not load items that are dripping wet.
• Carefully check all instructions on clothing
labels (see Laundry).
• Do not tumble dry large, very bulky items.
• Do not tumble dry acrylic fibres at high
temperatures.
• Do not turn off the dryer when there are
still warm items inside.
• Clean the filter after each use (see
Maintenance).
• Empty the water container after each use
(see Maintenance).
●• Clean the condenser unit at regular intervals
(see Maintenance).
●• Do not allow lint to collect around the
dryer.
• Never climb on top of the dryer. It could
result in damage.
• Always follow electrical standards and
requirements (see Installation).
• Always buy original spare parts and
accessories (see Service).
To minimise the risk of fire
in your tumble dryer, the
following should be observed:
• Tumble dry items only if they have been
washed with detergent and water, rinsed
and been through the spin cycle. It is a fire
hazard to dry items that HAVE NOT been
washed with water.
●• Do not dry garments that have been
treated with chemical products.
• Do not tumble dry items that have
been spotted or soaked with vegetable
or cooking oils, this constitutes a fire
hazard. Oil-affected items can ignite
spontaneously,especially when exposed
to heat sources such as a tumble dryer.
The items become warm, causing
an oxidisation reaction with the oil,
Oxidisation creates heat. If the heat
cannot escape, items can become hot
enough to catch fire. Piling, stacking or
storing oil-effected items can prevent
heat from escaping and so create a fire
hazard.If it is unavoidable that fabrics
containing vegetable or cooking oil or
those that have been contaminated with
hair care products be placed in a tumble
dryer they should first be washed with
extra detergent - this will reduce, but not
eliminate the hazard. They should not
be removed from the dryer and piled or
stacked while hot.
• Do not tumble dry items that have
previously been cleaned in or washed
in, soaked in or soiled with petrol/
gasoline, dry cleaning solvents or other
flammable or explosive substances. Highly
flammable substances commonly used in
domestic environments including cooking
oil, acetone, denatured alcohol, kerosene,
spot removers, turpentine, waxes and wax
removers. Ensure these items have been
washed in hot water with an extra amount
of detergent before being dried in the
tumble dryer.
●• Do not tumble dry items containing foam
rubber (also known as latex foam), or
similarly textured rubber like materials.
Foam rubber materials can, when heated,
produce fire by spontaneous combustion.
●• Fabric softener or similar products should
not be used in a tumble dryer to eliminate
the effects of static electricity unless the
practice is specifically recommended by the
manufacturer of the fabric softener product.
• Do not tumble dry undergarments that
contain metal reinforcements eg. bras
with metal reinforcing wires. Damage to
the tumble dryer can result if the metal
reinforcements come loose during drying.
●• Do not tumble dry rubber, plastic articles
such as shower caps or babies waterproof
covers, polythene or paper.
• Do not tumble dry rubber backed articles,
clothes fitted with foam rubber pads,
pillows, galoshes and rubber coated tennis
shoes.
• Remove all objects from pockets such as
lighters and matches.
! WARNING: Never stop the dryer before
the end of the drying cycle unless all
items are quickly removed and spread
out so that the heat is dissipated.
Save energy and respect the
environment
• Wring out all items to eliminate excess water
before tumble drying (if you use a washing
machine first, select a high spin cycle). Doing
this will save time and energy during drying.
• Always dry full loads - you save energy: single
items or small loads take longer to dry.
• Clean the filter after each use to contain energy
consumption costs (see Maintenance).
Warnings
Maximum load sizes: 8 kg
Power consumption
o-mode (Po) - Watts 0.14
left-on mode (Pl) - Watts 1.90
Programs Kg kWh Minutes
Eco Cotton* 8 4.76 149
Eco Cotton 4 2.54 86
Synthetics 31.58 65
* This is the reference programme for the energy label and suitable
to dry normal wet cotton laundry. This is the most ecient
programme in terms of energy consumption for drying wet cotton
laundry. (Standard/Default starting conguration).
5
GB
Disconnecting the power supply
! Disconnect the dryer when not in use or
during cleaning and maintenance operations.
Cleaning the filter after each
cycle
The filter is a fundamental component of the
dryer: its function is to collect lint and fluff that
form during drying.
Clean the filter once
drying is completed, by
rinsing it under
running water or cleaning
it with a vacuum cleaner.
Should the filter become
clogged, the flow of air
inside the dryer will be
seriously hampered:
drying times becomes
longer and more energy
is consumed. Also, the
dryer may become
damaged.
The filter is located in
front of the dryer seal (see Picture).
Removing the filter:
1. Pull the filter’s plastic handle upwards (see
Picture).
2. Clean the fluff off the filter and replace it
correctly. Ensure that the filter is pushed fully
home.
! Do not use the dryer unless the filter has
been replaced in its holder.
Checking the drum after each cycle
Rotate the drum manually to remove smaller items
(handkerchiefs) that could have been left inside the dryer.
Cleaning the drum
! Avoid using abrasives, steel wool or stainless steel cleaning
agents to clean the drum. A coloured film may appear on the
stainless steel drum surface: it may be caused by a
combination of water and/or cleaning agents such as wash-
softeners. This coloured film does not affect the dryer’s
performance.
Emptying the water container after
each cycle
2
Remove the water container and
empty it into a sink or other
suitable drain outlet, then
replace it correctly.
Always check the water
container and empty it before
starting a new drying cycle.
-Failure to empty the water container may cause
the following:
- The dryer stops heating (so the load may still be
damp at the end of the drying cycle).
- The “Empty water container” LED activates to
show that the water container is full.
Priming the Water Collection System
When your dryer is new, the Water Container will
not collect Water until the system is primed, this
will take 1 or 2 drying cycles. Once primed it will
collect Water during every cycle.
Cleaning the condenser unit.
• Remove the condenser (see Picture
below) unit regularly (monthly) and clean off
any fluff deposits from the plates by rinsing it
with cold water running on the rear end of the
condenser.
Removing the conden-
ser:
1. Disconnect the
dryer from the power
supply and open the
door.
2. Open the
condenser cover (see
Picture below), unlock the three catches by
turning them 90°
anti-clockwise, then pull
on the grip to remove
the condenser.
3. Clean the surface
of the seals and replace
the unit with the arrows
pointing upwards, whi-
2
Quick Tips
!Remember to clean your filter and
Condenser unit after each load.
! Remember to empty your water
container after each load.
! Doing this will keep your machine
working at its BEST!
Water container
Condenser Unit
Condenser cover
Catches
Filter
Handle
Air intake
Tap
Rear
Front
Condenser unit
le making sure that the catches are securely
fixed.
Cleaning the tumble dryer
• The external metal, plastic and rubber parts can be
cleaned with a damp cloth.
• Clean the front air intake grille regularly (every 6 months)
with a vacuum cleaner to remove any lint, fluff or dust
deposits. Furthermore, remove any lint deposits from the
front part of the condenser and from the filter area, using a
vacuum cleaner every so often.
! Do not use solvents or abrasives.
! Have the dryer checked regularly by authorised technical
personnel in order to ensure that the electrical and mechani-
cal parts work safely (see Assistance).
Care and maintenance
Rating plate
Model & Serial
Numbers
6
GB
Disconnecting the power supply
! Disconnect the dryer when not in use or
during cleaning and maintenance operations.
Cleaning the filter after each
cycle
The filter is a fundamental component of the
dryer: its function is to collect lint and fluff that
form during drying.
Clean the filter once
drying is completed, by
rinsing it under
running water or cleaning
it with a vacuum cleaner.
Should the filter become
clogged, the flow of air
inside the dryer will be
seriously hampered:
drying times becomes
longer and more energy
is consumed. Also, the
dryer may become
damaged.
The filter is located in
front of the dryer seal (see Picture).
Removing the filter:
1. Pull the filter’s plastic handle upwards (see
Picture).
2. Clean the fluff off the filter and replace it
correctly. Ensure that the filter is pushed fully
home.
! Do not use the dryer unless the filter has
been replaced in its holder.
Checking the drum after each cycle
Rotate the drum manually to remove smaller items
(handkerchiefs) that could have been left inside the dryer.
Cleaning the drum
! Avoid using abrasives, steel wool or stainless steel cleaning
agents to clean the drum. A coloured film may appear on the
stainless steel drum surface: it may be caused by a
combination of water and/or cleaning agents such as wash-
softeners. This coloured film does not affect the dryer’s
performance.
Emptying the water container after
each cycle
2
Remove the water container and
empty it into a sink or other
suitable drain outlet, then
replace it correctly.
Always check the water
container and empty it before
starting a new drying cycle.
-Failure to empty the water container may cause
the following:
- The dryer stops heating (so the load may still be
damp at the end of the drying cycle).
- The “Empty water container” LED activates to
show that the water container is full.
Priming the Water Collection System
When your dryer is new, the Water Container will
not collect Water until the system is primed, this
will take 1 or 2 drying cycles. Once primed it will
collect Water during every cycle.
Cleaning the condenser unit.
• Remove the condenser (see Picture
below) unit regularly (monthly) and clean off
any fluff deposits from the plates by rinsing it
with cold water running on the rear end of the
condenser.
Removing the conden-
ser:
1. Disconnect the
dryer from the power
supply and open the
door.
2. Open the
condenser cover (see
Picture below), unlock the three catches by
turning them 90°
anti-clockwise, then pull
on the grip to remove
the condenser.
3. Clean the surface
of the seals and replace
the unit with the arrows
pointing upwards, whi-
2
Quick Tips
!Remember to clean your filter and
Condenser unit after each load.
! Remember to empty your water
container after each load.
! Doing this will keep your machine
working at its BEST!
Water container
Condenser Unit
Condenser cover
Catches
Filter
Handle
Air intake
Tap
Rear
Front
Condenser unit
le making sure that the catches are securely
fixed.
Cleaning the tumble dryer
• The external metal, plastic and rubber parts can be
cleaned with a damp cloth.
• Clean the front air intake grille regularly (every 6 months)
with a vacuum cleaner to remove any lint, fluff or dust
deposits. Furthermore, remove any lint deposits from the
front part of the condenser and from the filter area, using a
vacuum cleaner every so often.
! Do not use solvents or abrasives.
! Have the dryer checked regularly by authorised technical
personnel in order to ensure that the electrical and mechani-
cal parts work safely (see Assistance).
Care and maintenance
Rating plate
Model & Serial
Numbers
7
GB
Control panel
Choosing a programme
1. Plug the dryer into the electrical socket.
2. Sort your laundry according to fabric type (see
Laundry).
3. Open the door and make sure the filter is clean and
in place and the water container is empty and in place
(see Maintenance).
4. Load the machine and make sure items are not in
the way of the door seal. Close the door.
5. If none of the lights are on: Press the ON/OFF
button
6. Choose a programme by checking the Programmes
Guide (see Programmes) as well as the indications for
each type of fabric (see Laundry).
- Select a programme by rotating the PROGRAMMES
knob.
7. Set a delay time and other options if necessary.
8. The START/PAUSE light is flashing green:
- press the START/PAUSE button to begin. The
green light stops flashing.
During the drying programme, you can check on your
laundry and take out items that are dry while others
continue drying. When you close the door again, press
the START/PAUSE button in order to resume drying.
(When the door is opened the START/PAUSE light will
flash Amber, after the door is closed and the START/
PAUSE button pressed, the START/PAUSE light
will stop flashing and show green.)
Note: During the Post Care phase this light flashes
Amber.
9. At the end of the drying cycle the End light come on
and either :
- The buzzer will beep 3 times to let you know that
your programme is complete.
or - If you have selected the Crease Care option and
you do not take the items out immediately, the items
will tumble occasionally for 10 hours or until you open
the door, the buzzer will then beep 3 times to confirm
the programme is completed.
10. Open the door, take the laundry out, clean the filter
and replace it. Empty the water container and replace
it (see Maintenance).
11. Unplug the dryer.
PROGRAMME
Knob Indicator
ON/OFF
Button
OPTION
Buttons & Lights
START/PAUSE
Button & Light
Empty Water Light
Clean Filter Light
Clean Condenser
Light
Progress or Delay
Lights
8
GB
The Controls
• PROGRAMMES knob
! Warning, if after pressing the Start/Pause button , the
programmes knob position has changed, the new position
will NOT change the programme selected. To change a
selected programme, press the Start/Pause button , the
light flashes Amber to indicate the programme is paused.
Select the new programme and any options required, the
light will then flash green. Press the Start/Pause button
again and the new programme will start.
• Option buttons / lights
These buttons are used to customise the
selectedprogramme to your requirements. Not all
options are available for all programmes (see Start and
Programmes). If an option is not available and you press
the button, the buzzer will beep three times. If the option is
available the option light next to the button lights to confirm
the selection.
Progress (Drying, Cool Tumble, End) /Delay (3hr, 6hr, 9hr)
Lights
When the light next to the delay button is on, these lights
flash to indicate the delay time selected. During other
programmes they indicate the progress of the dryer, each
one comes on as the corresponding phase starts.
Delay Timer
The start of some programmes (see Start and Programmes)
can be delayed for up to 9 hours in 3hr steps. Ensure the
water bottle is emptied before setting a delayed start. When
a delayed start is in progress the light next to the delay
button will be on and the selected delay period light will flash
(after the start button has been pressed). To set a delayed
start, press the Delay Timer button, and the light next to
the button will come on together with the 3hr delay light.
Pressing the button again will advance the delay setting to
6hr, the 3hr light goes out and the 6hr light is on. Each time
you press the button the delay setting advances 3 hours,
as indicated by the corresponding light. If the 9hr light is on,
pressing the button again will cancel the delay. Holding in
the On/Off button will also cancel.
Pre Care
When a delayed start and this option have been selected the
clothes are tumbled occasionally during the delayed period
to help prevent creases developing.
High Heat
Available for Timed Drying Programmes. Press this button
and a high heat setting is selected and the light next to the
button comes on. Timed programmes have a default of low
heat, if the light alongside the button is on then pressing the
button selects a low heat setting and the light goes out.
Post Care
When selected, the clothes are occasionally tumbled after
the end of the drying and cool tumble cycles, to help prevent
creases developing should you not be available to remove
the load immediately the programme is complete. The End
light is on during this phase.
Empty Water Light / Container
(If you have plumbed your dryer to a drain this light can be
ignored, as there is no need to empty the water container).
When this light is on (not flashing) it reminds you to empty
the water container. If the water container fills during a
programme, the heater turns off and the dryer does a period
of Cool Tumble then the light flashes and the buzzer sounds.
You must empty the water container and restart the dryer
or the clothes will not dry. After re-starting the dryer, the
light will take a few seconds to go out.To avoid this always
empty the water container each time you use the dryer (see
Maintenance).
• Door Opening
Opening the door (or pressing the Start/Pause button )
during a programme will stop the dryer and have the following
effects:
• The Start/Pause light flashes Amber.●
• During a delay phase the delay will continue to count down
The Start/Pause button must be pressed to resume the
delay programme.
One of the delay lights will flash to show the
current delay setting.
●•The Start/Pause button must be pressed to resume
the programme. The progress lights will change to show the
current status and the Start/Pause light will stop flashing and
turn green.
●•During the Post Care phase of a drying programme, the
programme will finish. Pressing the Start/Pause button will
re-start a new programme at the beginning.
●•Changing the programmes knob will select a new
programme and the Start/Pause light will flash green. You
can use this to select the Cool Tumble programme to
cool the clothes, if you find them dry enough. Press the Start/
Pause button to begin a new programme.
●• Note
●If you have a power cut, switch off the power or remove the
plug. When power is restored, press and hold the ON/OFF
button until the dryer reactivates, then press the Start/Pause
button.
Start and Programmes
9
GB
Programme What it does... How to set it... Note:
1
Cottons
Ready to Wear
Dries your clothes on High
Heat setting, ready for
wearing.
1. Position the PROGRAMMES
knob on
2. Select any options if required.
3. Press the Start/Pause button
Options available:
Delay Timer
Pre Care
Post Care
2
Standard
Cotton
Dries your clothes on High
Heat setting, ready for putting
away.
1. Position the PROGRAMMES
knob on
2. Select any options if required.
3. Press the Start/Pause button
Options available:
Delay Timer
Pre Care
Post Care
3
Synthetics
Cupboard dry
Dries your clothes on Low
Heat setting, ready for putting
away
1. Position the PROGRAMMES
knob on
2. Select any options if required.
3. Press the Start/Pause button
Options available:
Delay Timer
Pre Care
Post Care
4
Easy Iron
Brief programme
(approximately10 minutes) that
softens fibres of clothing that
is ready for ironing.
1. Position the PROGRAMMES
knob on
2. Press the Start/Pause button
! This is not a drying program-
me (see previous page).
Options available:
None
5
Cool Tumble
Brief programme
(approximately 20 minutes)
that cools fibres of clothing.
1. Position the PROGRAMMES
knob on
2. Press the Start/Pause button
Options available:
None
Timed Drying
(150, 140, 120,100,
80, 70, 60,50, 40, 30
or 20 minutes)
Dries wet clothing that you
wish to dry on Low Heat or
small loads (less than 1kg).
Can be used with High Heat
option if you prefer to use a
timed programme.
1. Position the PROGRAMMES
knob on the desired time: 150,
140, 120, 100, 80, 70, 60, 50, 40,
30 or 20.
2. Select any options if required.
3. Press the Start/Pause button
Options available:
High Heat
Delay Timer
Pre Care
Post Care
Consult ‘suggested drying
times’ (see Laundry).
The last 10 minutes of these
programmes is the Cool
Tumble phase.
Programmes
!If none of the lights are lit; Press the ON/OFF button and then select programme.
2 Standard Cotton
•This is a programme for cotton items.
•The duration of this programme will depend on the size of the load, the dryness setting selected and the spin speed used in
your washer (see Laundry).
•The Standard Cotton programme to EU Regulation 392/2012 is Programme 1 selection with High Heat and Dryness Level
Cupboard Dry (the standard/default configuration). This is the most efficient programme in terms of energy consumption (EU
392/2012).
4 Easy Iron Programme
‘Easy Iron’ is a short 10 minute programme (8 minutes of heat followed by a 2 minute cool tumble period) which fluffs the fibres of
clothing that have been left in the same position/location for an extended period of time. The cycle relaxes the fibres and makes
them easier to iron and fold.
!‘Easy Iron’ is not a drying programme and should not be used for wet articles of clothing.
For best results:
1.Do not load more than the maximum capacity.
These numbers refer to the dry weight:
Fabric Maximum load
Cotton and Cotton mixtures 2.5kg
Synthetics 2kg
Denim 2kg
2.Unload the dryer immediately after the end of the programme, hang, fold or iron the articles and put them away in the closet.
Should this not be possible repeat the programme.
The ‘Easy Iron’ effect varies from one fabric to the next. It works well on traditional fabrics like Cotton or Cotton mix, and less well
on acrylic fibres and on materials such as Tencel®.
10
GB
Sorting laundry
• Check the symbols on the care labels of the various gar-
ments to verify whether the garments can be safely tumble
dried.
• Sort laundry according to the type of fabric.
• Empty all pockets and check for loose buttons.
• Close zips and hooks and fasten belts and strings without
tightening them.
• Wring out garments to remove the maximum amount of
water possible.
! Do not load the dryer when garments are dripping wet.
Maximum load sizes
Do not overload the drum.
The following values indicate the weight of dry garments:
Natural fibres: maximum kg
Synthetic fibres: maximum kg
! Do not overload the dryer as this may result is reduced
drying performance.
Care labels
Always check the care labels, especially when placing
garments in the tumble dryer for the first time. Below are the
most commonly used symbols:
May be tumble dried.
Do not tumble dry.
Tumble dry – high heat.
Tumble dry – low heat.
Drying times
Drying times are approximate and may vary depending on
the following:
• Amount of water retained by items after the spin cycle:
towels and delicate items retain a lot of water.
• Fabrics: items of the same fabric, but with different texture
and thickness may have different drying times.
• Amount of laundry: single items and small loads may take
longer to dry.
• Drying: if items are to be ironed, they can be removed
from the dryer while still slightly damp. Items that require
complete drying can be left longer.
• Heat setting.
• Temperature of the room: the lower the temperature of the
room, the longer it will take for the dryer to dry clothing.
• Bulk: certain bulky items require special care during the
drying process. We suggest removing these items and
replacing them in the dryer once they have been shaken
out: repeat this procedure several times during the course
of the drying cycle.
! Do not over-dry items.
All fabrics contain natural dampness which helps to keep
them soft and fluffy.
The drying times provided refer to the automatic Cupboard
dry programmes.
The Timed drying settings are also indicated to enable you
to select the most suitable timed option.
The weight refers to dry items.
Laundry
Cottons High Heat - spin speed 800-1000 rpm in washing machine.
Load size 1 kg 2 kg 3 kg 4 kg 5 kg 6 kg 7-8 kg
Drying times,
in minutes 30 - 40 40 - 55 55 - 70 70 - 80 80 - 90 95 - 120 120 - 150
Synthetics Low Heat - on reduced spin in washing machine.
Load size 1 kg 2 kg 3 kg
Drying times,
in minutes 40 - 50 50 - 70 70 - 90
Note:
At the end of a drying cycle, cottons could still be damp if you grouped cottons and synthetics together.
If this is the case, simply give the damp cotton items an additional short period of drying.
8
3
11
GB
Sorting laundry
• Check the symbols on the care labels of the various gar-
ments to verify whether the garments can be safely tumble
dried.
• Sort laundry according to the type of fabric.
• Empty all pockets and check for loose buttons.
• Close zips and hooks and fasten belts and strings without
tightening them.
• Wring out garments to remove the maximum amount of
water possible.
! Do not load the dryer when garments are dripping wet.
Maximum load sizes
Do not overload the drum.
The following values indicate the weight of dry garments:
Natural fibres: maximum kg
Synthetic fibres: maximum kg
! Do not overload the dryer as this may result is reduced
drying performance.
Care labels
Always check the care labels, especially when placing
garments in the tumble dryer for the first time. Below are the
most commonly used symbols:
May be tumble dried.
Do not tumble dry.
Tumble dry – high heat.
Tumble dry – low heat.
Drying times
Drying times are approximate and may vary depending on
the following:
• Amount of water retained by items after the spin cycle:
towels and delicate items retain a lot of water.
• Fabrics: items of the same fabric, but with different texture
and thickness may have different drying times.
• Amount of laundry: single items and small loads may take
longer to dry.
• Drying: if items are to be ironed, they can be removed
from the dryer while still slightly damp. Items that require
complete drying can be left longer.
• Heat setting.
• Temperature of the room: the lower the temperature of the
room, the longer it will take for the dryer to dry clothing.
• Bulk: certain bulky items require special care during the
drying process. We suggest removing these items and
replacing them in the dryer once they have been shaken
out: repeat this procedure several times during the course
of the drying cycle.
! Do not over-dry items.
All fabrics contain natural dampness which helps to keep
them soft and fluffy.
The drying times provided refer to the automatic Cupboard
dry programmes.
The Timed drying settings are also indicated to enable you
to select the most suitable timed option.
The weight refers to dry items.
Laundry
Troubleshooting
Possible causes / Solution:
• The plug is not plugged into the socket, or not making contact.
• There has been a power failure.
• The fuse has blown. Try to plug another appliance into the socket.
• You are using an extension cord? Try to plug the dryer’s power cord directly into the
socket.
• The door is not closed securely?
• The programme has not been set properly (see Start and Programmes).
• The Start/Pause button has not been pressed (see Start and Programmes).
• You have set a delayed time (see Start and Programmes).
• The filter has not been cleaned (see Maintenance).
• The water container needs emptying? The empty water light is flashing? (see Main-
tenance).
• The condenser needs cleaning? (see Maintenance).
• The temperature setting is not ideal for the type of fabric you are drying (see Start
and Programmes, and see Laundry).
• The correct drying time has not been selected for the load (see Laundry).
• The air intake grille is obstructed (see Installation, and see Maintenance).
• The items were too wet (see Laundry).
• The dryer was overloaded (see Laundry).
• The water container was probably not emptied at the start of the programme. Do not
wait for the empty water signal, always check and empty the container before starting
a new drying programme (see Maintenance).
• This is normal, the light flashes when the container is full. If the light is on but not
flashing it is just a reminder to empty the container (see Start and Programmes).
• If the Option lights and the START/PAUSE light flash together with other lights on,
then:
- Turn off and remove the plug. Clean the filter and the condenser (see
Maintenance). Then replace the plug, turn on and start another programme. If
the same combination of lights are on, note down the lights and contact the
Service Centre (see Service).
! For safety the dryer has a maximum programme time of 5 hours. If an automatic
programme has not sensed the required final moisture in this time the dryer will
complete the programme and stop. Check the above points and run the programme
again, if the results are still damp, contact the Service Centre (see Service).
Problem:
The tumble dryer won’t start.
Drying cycle will not begin.
Its taking a long time to dry.
Empty water light is flashing but the
dryer has only been running for a short
period.
Empty water light is on and the water
container is not full.
The OPTION lights and the START/
PAUSE light Flash amber.
Programme finishes and clothes are
damper thanexpected..
One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the following
troubleshooting suggestions:
Note:
This tumble dryer, in compliance with new energy saving regulations, is fitted with an automatic standby system which is enabled after about 30
minutes if no activity is detected. Press and hold the ON-OFF button until the dryer reactivates.
12
GB
01/2018
19515921300
Service
This appliance has been designed, constructed and distributed in compliance with the
requirements of European Directives:
- LVD 2014/35/EU, EMC 2014/30/EU and RoHS 2011/65/EU.
Information on recycling and disposal
As part of our continual commitment towards environmental protection, we reserve the right to use recycled quality components to
reduce costs for our customers and to minimise materials wastage.
• Disposing of the packaging materials: follow local regulations to allow for recycling of packaging materials.
• In order to minimise the risk of injury to children, remove the door and plug, then cut the power supply cord flush with the ap-
pliance. Dispose of these parts separately to prevent the appliance from being connected to a power supply socket.
Disposal of old household appliances
European Directive 2012/19/EC concerning Waste Electrical and Electronic Equipment (WEEE) states that household
appliances should not be disposed of using the normal solid urban waste cycle. Exhausted appliances should be collected
separately in order to optimise the cost of re-using and recycling materials comprising the machine, while preventing
potential damage to public health and the environment. The crossed-out wheeled bin symbol appears on all products to
remind owners of the obligations regarding separate waste collection.
Owners should contact their local authorities or appliance dealers for further information concerning the correct disposal of hou-
sehold appliances.
Before contacting the Technical Assistance Centre:
• Follow the troubleshooting guide to check whether pro-
blems can be solved personally (see Troubleshooting).
• If not, switch the dryer off and contact the Technical Assi-
stance Centre closest to you.
Spare parts
This dryer is a complex machine. Attempting to repair it per-
sonally or with the aid of an unqualified personnel may put
the safety of people at risk, damage the machine or invalida-
te the spare parts guarantee.
Always contact a qualified technician when experiencing
problems with this machine.