Table of Contents
- Product description
- Components
- Illustrated parts catalog
- Removal and replacement procedures preliminary requirements
- Removal and replacement procedures for Customer Self-Repair parts
- Removal and replacement procedures for Authorized Service Provider parts
- Computer Setup (BIOS), TPM, and HP Sure Start
- Using HP PC Hardware Diagnostics (UEFI)
- Backup and recovery
- Specifications
- Statement of memory volatility
- Power cord set requirements
- Recycling
- Index
HP 470 G4 User Manual
Displayed below is the user manual for 470 G4 by HP which is a product in the Notebooks category. This manual has pages.
Related Manuals
HP ProBook 470 G4 Notebook PC
Maintenance and Service Guide
© Copyright 2016 HP Development Company,
L.P.
AMD is a trademark of Advanced Micro Devices,
Inc. Bluetooth is a trademark owned by its
proprietor and used by HP Inc. under license.
Intel is a trademark of Intel Corporation in the
U.S. and other countries. Microsoft and
Windows are trademarks of the Microsoft
group of companies.
The information contained herein is subject to
change without notice. The only warranties for
HP products and services are set forth in the
express warranty statements accompanying
such products and services. Nothing herein
should be construed as constituting an
additional warranty. HP shall not be liable for
technical or editorial errors or omissions
contained herein.
First Edition: September 2016
Document Part Number: 903120-001
Product notice
This user guide describes features that are
common to most models. Some features may
not be available on your computer.
Not all features are available in all editions of
Windows. This computer may require upgraded
and/or separately purchased hardware, drivers
and/or software to take full advantage of
Windows functionality. Go to
http://www.microsoft.com for details.
Your product does not support Windows 8 or
Windows 7
In accordance with Microsoft’s support policy,
HP does not support the Windows 8 or
Windows 7 operating system on this product or
provide any Windows 8 or Windows 7 drivers
on http://support.hp.com.
Software terms
By installing, copying, downloading, or
otherwise using any software product
preinstalled on this computer, you agree to be
bound by the terms of the HP End User License
Agreement (EULA). If you do not accept these
license terms, your sole remedy is to return the
entire unused product (hardware and software)
within 14 days for a full refund subject to the
refund policy of your seller.
For any further information or to request a full
refund of the price of the computer, please
contact your seller.
Important Notice about Customer Self-Repair Parts
CAUTION: Your computer includes Customer Self-Repair parts and parts that should only be accessed by an
authorized service provider. See Chapter 5, "Removal and replacement procedures for Customer Self-Repair
parts," for details. Accessing parts described in Chapter 6, "Removal and replacement procedures for
Authorized Service Provider only parts," can damage the computer or void your warranty.
iii
iv Important Notice about Customer Self-Repair Parts
Safety warning notice
WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place
the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, at
surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as
pillows or rugs or clothing, to block airow. Also, do not allow the AC adapter to contact the skin or a soft
surface, such as pillows or rugs or clothing, during operation. The computer and the AC adapter comply with
the user-accessible surface temperature limits dened by the International Standard for Safety of
Information Technology Equipment (IEC 60950-1).
v
vi Safety warning notice
Table of contents
1 Product description ....................................................................................................................................... 1
2 Components .................................................................................................................................................. 5
Right ....................................................................................................................................................................... 5
Left ......................................................................................................................................................................... 6
Display .................................................................................................................................................................... 7
Top .......................................................................................................................................................................... 8
TouchPad ............................................................................................................................................. 8
Lights ................................................................................................................................................... 9
Buttons, speakers, and ngerprint reader ........................................................................................ 10
Special function keys ........................................................................................................................ 11
Using the hot keys ............................................................................................................................. 12
Bottom ................................................................................................................................................................. 13
Labels ................................................................................................................................................................... 14
3 Illustrated parts catalog .............................................................................................................................. 15
Computer major components .............................................................................................................................. 15
Cable Kit ............................................................................................................................................................... 18
Display components ............................................................................................................................................ 19
Plastics Kit ........................................................................................................................................................... 21
Mass storage devices ........................................................................................................................................... 22
Miscellaneous parts ............................................................................................................................................. 23
4 Removal and replacement procedures preliminary requirements .................................................................... 25
Tools required ...................................................................................................................................................... 25
Service considerations ......................................................................................................................................... 25
Plastic parts ....................................................................................................................................... 25
Cables and connectors ...................................................................................................................... 26
Drive handling ................................................................................................................................... 26
Grounding guidelines ........................................................................................................................ 27
Electrostatic discharge damage ..................................................................................... 27
Packaging and transporting guidelines ....................................................... 28
Workstation guidelines ................................................................................ 28
Equipment guidelines ................................................................................... 29
vii
5 Removal and replacement procedures for Customer Self-Repair parts ............................................................. 30
Component replacement procedures .................................................................................................................. 30
Battery Safe mode ............................................................................................................................ 30
Service door ....................................................................................................................................... 31
Optical drive ....................................................................................................................................... 32
Hard drive .......................................................................................................................................... 34
Memory modules ............................................................................................................................... 36
WLAN/Bluetooth combo card ............................................................................................................ 38
M.2 solid-state drive ......................................................................................................................... 40
Keyboard ........................................................................................................................................... 41
6 Removal and replacement procedures for Authorized Service Provider parts ................................................... 44
Component replacement procedures .................................................................................................................. 44
Display subcomponents (bezel, webcam, panel) ............................................................................. 44
Top cover ........................................................................................................................................... 48
Fingerprint reader assembly ............................................................................................................. 52
Power button board .......................................................................................................................... 54
Function board .................................................................................................................................. 56
Speaker assembly ............................................................................................................................. 58
TouchPad assembly ........................................................................................................................... 60
Battery ............................................................................................................................................... 62
USB/audio board ................................................................................................................................ 64
Fan ..................................................................................................................................................... 66
Optical drive connector cable ............................................................................................................ 68
System board .................................................................................................................................... 70
RTC battery ........................................................................................................................................ 73
Heat sink assembly ........................................................................................................................... 74
Display assembly ............................................................................................................................... 76
Power connector and cable ............................................................................................................... 83
7 Computer Setup (BIOS), TPM, and HP Sure Start ............................................................................................. 84
Using Computer Setup ......................................................................................................................................... 84
Starting Computer Setup .................................................................................................................. 84
Navigating and selecting in Computer Setup ................................................................................... 84
Restoring factory settings in Computer Setup ................................................................................. 84
Updating the BIOS ............................................................................................................................. 85
Determining the BIOS version ......................................................................................... 85
Downloading a BIOS update ........................................................................................... 86
Changing the boot order using the f9 prompt .................................................................................. 86
TPM BIOS settings (select products only) ........................................................................................................... 87
viii
Using HP Sure Start (select products only) ......................................................................................................... 87
8 Using HP PC Hardware Diagnostics (UEFI) ....................................................................................................... 88
Downloading HP PC Hardware Diagnostics (UEFI) to a USB device .................................................................... 88
Blink and beep codes ........................................................................................................................................... 89
9 Backup and recovery .................................................................................................................................... 90
Creating recovery media and backups ................................................................................................................ 90
Creating HP Recovery media (select products only) ......................................................................... 90
Using Windows tools ........................................................................................................................................... 91
Restore and recovery ........................................................................................................................................... 92
Recovering using HP Recovery Manager ........................................................................................... 92
What you need to know before you get started ............................................................. 92
Using the HP Recovery partition (select products only) ................................................. 93
Using HP Recovery media to recover .............................................................................. 93
Changing the computer boot order ................................................................................ 94
Removing the HP Recovery partition (select products only) ......................................... 95
10 Specications ............................................................................................................................................ 96
Computer specications ...................................................................................................................................... 96
43.9-cm (17.3-in) display specications ............................................................................................................. 97
Hard drive specications ..................................................................................................................................... 98
Solid-state drive specications ........................................................................................................................... 99
DVD±RW SuperMulti DL Drive specications .................................................................................................... 100
Blu-ray ROM DVD±RW SuperMulti DL Drive ....................................................................................................... 101
DVD-ROM drive .................................................................................................................................................. 102
11 Statement of memory volatility ................................................................................................................ 103
Nonvolatile memory usage ............................................................................................................................... 106
Questions and answers ..................................................................................................................................... 108
Using HP Sure Start (select models only) .......................................................................................................... 109
12 Power cord set requirements .................................................................................................................... 110
Requirements for all countries and regions ...................................................................................................... 110
Requirements for specic countries and regions ............................................................................................. 110
13 Recycling ................................................................................................................................................ 112
Index ........................................................................................................................................................... 113
ix
x
1 Product description
Category Description
Product Name HP ProBook 470 G4 Notebook PC
Processors 7th generation, Intel® Core™ i7 processor, Dual Core (4-MB L3 cache, 15 W)x
7500U, 2.7 GHz/3.5 GHz Single Core Turbo; Intel HD Graphics 620
7th generation, Intel Core i5 processor, Dual Core (3-MB L3 cache, 15 W)
7200U, 2.5-GHz/3.1-GHz Single Core Turbo processor; Intel HD Graphics 620
7th generation, Intel Core i3 processor, Dual Core (3-MB L3 cache, 15 W)
7100U, 2.4-GHz processor; Intel HD Graphics 620
Graphics Switchable discrete graphics
Nvidia GeForce 930MX with 2 GB dedicated video memory
Supports HD decode, DX12, HDMI
Supports CUDA, Optimus, PhysX, GPU Boost 2.0
Panel 17.3-inch (LED backlight) 16:9 aspect ratio
HD eDP - at
43.9-cm (17.3-inch), anti-glare, HD+, 1600x900, at (4.0 mm), SVA, 220 nits, camera, 1 or 2 WLAN antennas
FHD eDP - at
43.9-cm (17.3-inch), anti-glare, FHD, 1920x1080, at (4.0 mm), UWVA, 300 nits, camera, 1 or 2 WLAN antennas
Memory Two customer-accessible memory module slots supporting up to 16 GB of RAM
Supports dual-channel memory
PC4-17000, 2133-MHz, DDR4 SODIMMs
Supports the following congurations:
●16384 MB (8192 × 2; dual channel)
●12288 MB (8192 + 4096; dual channel)
●8192 MB (8192 × 1)
●8192 MB (4096 × 2; dual channel)
●4096 MB (4096 × 1)
Primary storage Supports hard drives with HP 3D DriveGuard
Customer-accessible
Supports the following 7 mm/9.5 mm, 2.5 inch hard drives:
●2.0-TB, 5400-rpm
●1-TB, 5400-rpm
●500-GB, 7200-rpm
●500-GB, hybrid (8-GB SSD)
1
Category Description
●500-GB, 5400-rpm
Fixed optical drives Supports the following 9.5-mm SATA optical drives:
●DVD-ROM
●DVD+/-RW SuperMulti DL
●Blu-ray ROM DVD+/-RW SuperMulti DL
Supports no optical drive option
Primary M.2
storage
M.2 2280 SSD (NGFF), SATA-3
Supports the following drives:
●256 GB
●128 GB
Set as primary storage if selected.
Audio/Visual Audio controls
Integrated camera (720p HD)
Stereo speakers (2)
Integrated dual-array microphone (webcam models only)
Headphone/microphone combo jack
Ethernet Realtek RTL8111HSH 10/100/1000
S3/S4/S5 wake on LAN (AC mode and battery mode)
Wireless Integrated WLAN options by way of wireless module
WLAN antennas built into display assembly
Supports “no WLAN/Bluetooth” option
●Realtek RTL8723BE-VB 802.11b/g/n 1x1 Wi-Fi + Bluetooth 4.0 combination WLAN adapter
●Intel Dual Band Wireless-AC 3168 802.11ac, Dual Band, 1×1 Wi-Fi + Bluetooth 4.0
●Intel Dual Band Wireless-AC 8265, 802.11ac, 2×2 Wi-Fi + Bluetooth 4.2 combination adapter
●Intel Dual Band Wireless-AC 7265NV (non v-Pro) 802.11ac 2×2 WiFi + Bluetooth 4.2 combination adapter
Wireless Personal Area Network (PAN) Bluetooth
Bluetooth 4.0 supported using combo card
External media
card
Digital Media Reader Slot
Supports SD, SDHC, SDXC
Ports Headphone/microphone combo jack
RJ-45 (Ethernet, includes link and activity lights)
USB 3.0 (1)
USB 2.0 (2)
VGA (Dsub 15-pin) supporting 2048 × 1536 external resolution at 60-GHz (hot plug/unplug with auto-detect)
HDMI 1.4
Multi-pin AC port
2 Chapter 1 Product description
Category Description
Docking Docking connector
Keyboard/pointing
devices
Keyboards
HP Premium Keyboard
Full-sized, chiclet, spill-resistant keyboard with numeric keypad (backlit or not backlit)
Touchpad requirements
Windows 10 gestures: taps enabled by default: on/o control by driver, 2-nger scrolling and zoom enabled by
default, OSD (enable/disable), 3-nger tap - Cortana, 3- nger ick - App switch, 4-nger tap - Action Center
Power
requirements
AC adapters
65-W Smart AC adapter
Power cords
3-wire plug - 1.8 m
3-wire plug - 1.0 m
Battery
3-cell, 48-Wh, 4.21-Whr Li-ion battery
Security Integrated ngerprint reader
Supports “No ngerprint reader” option
Security lock
TPM 2.0 SLB9670 (Inneon; soldered down)
Operating system Operating system versionx
Windows 10: Threshold 2
Preinstalled
Windows 10 Home 64
Windows 10 Home 64 Single Language
Windows 10 Home 64 StF MSNA for Higher Education - Strategic
Windows 10 Home 64 High-end
Windows 10 Home 64 High-end Single Language
Windows 10 Professional 64
Windows 10 Professional 64 - StF MSNA - Standard
Windows 10 Professional 64 - StF MSNA - High End
Windows 10 Professional 64 - StF MSNA - Strategic
FreeDOS 2.0
Restore Media (DRDVD/SRDVD)
DRDVD Windows 10
Restore Media (OSDVD)
Windows 10 Professional 64
Web-only support
Windows 10 Enterprise
3
Category Description
Certied
Microsoft WHQL
Serviceability End-user replaceable parts
AC adapter
Hard drive
Optical drive
M.2 solid-state drive
Memory module
WLAN module
Keyboard
xYour product does not support Windows 8 or Windows 7. In accordance with Microsoft’s support policy, HP does not support the
Windows 8 or Windows 7 operating system on this product or provide any Windows 8 or Windows 7 drivers on
http://www.support.hp.com.
4 Chapter 1 Product description
2 Components
Right
Component Description
(1) Optical drive (select products only) Depending on your computer model, reads an optical disc or reads and
writes to an optical disc.
(2) Optical drive eject button (select
products only)
Releases the optical drive disc tray.
(3) Audio-out (headphone)/Audio-in
(microphone) combo jack
Connects optional powered stereo speakers, headphones, earbuds, a
headset, or a television audio cable. Also connects an optional headset
microphone. This jack does not support optional standalone microphones.
WARNING! To reduce the risk of personal injury, adjust the volume
before putting on headphones, earbuds, or a headset. For additional
safety information, refer to the Regulatory, Safety, and Environmental
Notices.
To access this guide:
1. Type support in the taskbar search box, and then select the HP
Support Assistant app.
‒ or –
Click the question mark icon in the taskbar.
2. Select My PC, select the Specications tab, and then select User
Guides.
NOTE: When a device is connected to the jack, the computer speakers
are disabled.
(4) USB 2.0 ports (2) Connect an optional USB device, such as a keyboard, mouse, external
drive, printer, scanner or USB hub.
(5) RJ-45 (network) jack/status lights Connects a network cable.
●Green (left): The network is connected.
●Amber (right): Activity is occurring on the network.
(6) Security cable slot Attaches an optional security cable to the computer.
NOTE: The security cable is designed to act as a deterrent, but it may
not prevent the computer from being mishandled or stolen.
Right 5
Left
Component Description
(1) Power connector Connects an AC adapter.
(2) Battery light When AC power is connected:
●White: The battery charge is greater than 90 percent.
●Amber: The battery charge is from 0 to 90 percent.
●O: The battery is not charging.
When AC power is disconnected (battery not charging):
●Blinking amber: The battery has reached a low battery
level. When the battery has reached a critical battery level,
the battery light begins blinking rapidly.
●O: The battery is not charging.
(3) Vent Enables airow to cool internal components.
NOTE: The computer fan starts up automatically to cool
internal components and prevent overheating. It is normal for
the internal fan to cycle on and o during routine operation.
(4) External monitor port Connects an external VGA monitor or projector.
(5) HDMI port Connects an optional video or audio device, such as a high-
denition television, any compatible digital or audio component,
or a high-speed High Denition Multimedia Interface (HDMI)
device.
(6) USB 3.0 port Connects an optional USB device, such as a keyboard, mouse,
external drive, printer, scanner or USB hub.
(7) USB Type-C charging port Connects any USB device with a Type-C connector and can charge
products such as cell phones, laptops, tablets, and MP3 players.
(8) Memory card reader Reads optional memory cards that store, manage, share, or
access information.
(9) Drive light ●Blinking white: The hard drive is being accessed.
●Amber: HP 3D DriveGuard has temporarily parked the hard
drive.
6 Chapter 2 Components
Display
NOTE: Refer to the illustration that most closely matches your computer.
Component Description
(1) WLAN antennas* (select products only) Send and receive wireless signals to communicate with wireless local
area networks (WLANs).
(2) WWAN antennas* (select products only) Send and receive wireless signals to communicate with wireless wide
area networks (WWANs).
(3) Internal microphones (1 or 2 depending on model) Record sound.
(4) Webcam light (select products only) On: The webcam is in use.
(5) Webcam (select products only) Records video and captures photographs. Some models allow you to
video conference and chat online using streaming video.
To use the webcam:
▲Type camera in the taskbar search box, and then select
Camera.
*The antennas are not visible from the outside of the computer. For optimal transmission, keep the areas immediately around the
antennas free from obstructions.
For wireless regulatory notices, see the section of the Regulatory, Safety, and Environmental Notices that applies to your country or
region.
To access this guide:
1. Type support in the taskbar search box, and then select the HP Support Assistant app.
‒ or –
Click the question mark icon in the taskbar.
2. Select My PC, select the Specications tab, and then select User Guides.
Display 7
Top
TouchPad
Component Description
(1) TouchPad zone Reads your nger gestures to move the pointer or activate
items on the screen.
(2) Left TouchPad button Functions like the left button on an external mouse.
(3) Right TouchPad button Functions like the right button on an external mouse.
8 Chapter 2 Components
Lights
Component Description
(1) Power light ●On: The computer is on.
●Blinking: The computer is in the Sleep state, a power-saving
state. The computer shuts o power to the display and
other unneeded components.
●O: The computer is o or in Hibernation. Hibernation is a
power-saving state that uses the least amount of power.
(2) Caps lock light On: Caps lock is on, which switches the key input to all capital
letters.
(3) Microphone mute light ●Amber: microphone sound is o.
●O: microphone sound is on.
(4) Num lock light On: Num lock is on.
(5) Wireless light On: An integrated wireless device, such as a wireless local area
network (WLAN) device and/or a Bluetooth® device, is on.
NOTE: On some models, the wireless light is amber when all
wireless devices are o.
(6) Mute light ●Amber: Computer sound is o.
●White: Computer sound is on.
Top 9
Buttons, speakers, and ngerprint reader
Component Description
(1) Power button ●When the computer is o, press the button to turn on the computer.
●When the computer is on, press the button briey to initiate Sleep.
●When the computer is in the Sleep state, press the button briey to exit
Sleep.
●When the computer is in Hibernation, press the button briey to exit
Hibernation.
CAUTION: Pressing and holding down the power button results in the loss of
unsaved information.
If the computer has stopped responding and shutdown procedures are
ineective, press and hold the power button for at least 5 seconds to turn o
the computer.
To learn more about your power settings, see your power options.
▲Type power in the taskbar search box, and then select Power and sleep
settings.
‒ or –
Right-click the Start button, and then select Power Options.
(2) Speakers (2) Produce sound.
(3) Wireless button Turns the wireless feature on or o but does not establish a wireless connection.
A wireless network must be set up before a wireless connection is possible.
(4) Volume mute button Mutes and restores speaker sound.
(5) Fingerprint reader (select
products only)
Allows a ngerprint logon to Windows, instead of a password logon.
10 Chapter 2 Components
Special function keys
Component Description
(1) esc key Displays system information when pressed in combination with
the fn key.
(2) fn key Executes frequently used system functions when pressed in
combination with a function key, the num lock key, or the the
esc key.
See Using the hot keys on page 12.
(3) Windows key Opens the Start menu.
NOTE: Pressing the Windows key again will close the Start
menu.
(4) num lock key Alternates between the navigational and numeric functions on
the integrated numeric keypad.
(5) Integrated numeric keypad A separate keypad to the right of the alphabet keyboard that
enables you to add, subtract, and perform other numeric tasks.
When num lock is on, the integrated keypad can be used like an
external numeric keypad.
Top 11
Using the hot keys
To use a hot key:
▲Press the fn key, and then press the correct function key represented by the icons below.
Press fn+function key Description
Initiates Sleep, which saves your information in system memory. The display and other system components
turn o and power is conserved.
To exit Sleep, briey press the power button.
CAUTION: To reduce the risk of information loss, save your work before initiating Sleep.
Turns the keyboard backlight o or on.
NOTE: To conserve battery power, turn o this feature.
Switches the screen image between display devices connected to the system. For example, if a monitor is
connected to the computer, repeatedly pressing this key alternates the screen image from the computer
display to the monitor display to a simultaneous display on both the computer and the monitor.
Decreases the screen brightness incrementally as long as you hold down the key.
Increases the screen brightness incrementally as long as you hold down the key.
Decreases speaker volume incrementally while you hold down the key.
Increases speaker volume incrementally while you hold down the key.
Mutes the microphone.
12 Chapter 2 Components
Bottom
Component Description
(1) Service door Provides access to the hard drive bay, the WLAN module
slot, the WWAN module slot, the SIM card slot, and the
memory module slots.
CAUTION: To prevent an unresponsive system, replace
the wireless module only with a wireless module
authorized for use in the computer by the governmental
agency that regulates wireless devices in your country or
region. If you replace the module and then receive a
warning message, remove the module to restore computer
functionality, and then contact support.
▲Type support in the taskbar search box, and then
select the HP Support Assistant app.
- or -
Click the question mark icon in the taskbar.
(2) SIM card slot or locking hinged connector
(select products only)
Supports a wireless subscriber identity module (SIM) card.
The SIM card slot or locking hinged connector is located
under the service door.
(3) Vents (2) Enable airow to cool internal components.
NOTE: The computer fan starts up automatically to cool
internal components and prevent overheating. It is normal
for the internal fan to cycle on and o during routine
operation.
Bottom 13
Labels
The labels axed to the computer provide information you may need when you troubleshoot system
problems or travel internationally with the computer.
IMPORTANT: Check the following locations for the labels described in this section: the bottom of the
computer, inside the battery bay, under the service door, or on the back of the display.
●Service label—Provides important information to identify your computer. When contacting support, you
will probably be asked for the serial number, and possibly for the product number or the model number.
Locate these numbers before you contact support.
Your service label will resemble one of the examples shown below. Refer to the illustration that most
closely matches the service label on your computer.
Component
(1) Serial number
(2) Product number
(3) Warranty period
(4) Model number (select products only)
Component
(1) HP product name
(2) Product ID number
(3) Serial number
(4) Warranty period
●Regulatory label(s)—Provide(s) regulatory information about the computer.
●Wireless certication label(s)—Provide(s) information about optional wireless devices and the approval
markings for the countries or regions in which the devices have been approved for use.
14 Chapter 2 Components
3 Illustrated parts catalog
Computer major components
NOTE: HP continually improves and changes product parts. For complete and current information on
supported parts for your computer, go to http://partsurfer.hp.com, select your country or region, and then
follow the on-screen instructions.
NOTE: Details about your computer, including model, serial number, product key, and length of warranty,
are on the service tag at the bottom of your computer. See Labels on page 14 for details.
Computer major components 15
Item Description Spare part number
(1) Display panel assembly, 35.6-cm (14.0-inch)
Displays are ONLY spared at the subcomponent level. For more information about display
components, see Display components on page 19.
(2) Keyboard (includes cable)
NOTE: For a detailed list of keyboard country codes, see Keyboard on page 41.
No backlight 827028-xxx
Backlit 827029-xxx
(3) Power button board 905754-001
(4) Top cover (includes touchpad assembly) 905996-001
(5) Function board 910959-001
(6) Fingerprint reader assembly (includes cable) 906003-001
(7) Speaker assembly 906004-001
(8) Battery, Li-ion (4-cell, 48 WHr, 4.21 Ah) 851610-855
(9) Fan 905774-001
(10) USB/audio board 905755-001
(11) Optical drive cable and connector
The optical drive connector cable is included in the Cable Kit.
906000-001
(12) Power connector cable 828949-007
(13) System board (includes replacement thermal material)
All system boards use the following part numbers:
xxxxxx-001: Non-Windows operating system
xxxxxx-601: Windows 10 operating system
Intel Core i7-7500U processor; 2-GB discrete graphics memory 907715-xxx
Intel Core i5-7200U processor; 2-GB discrete graphics memory 907714-xxx
Intel Core i3-7100U processor; 2-GB discrete graphics memory 907713-xxx
(14) Heat sink assembly (for discrete graphics; includes replacement thermal material) 907364-001
(15) RTC battery not spared
(16) Base enclosure 905995-001
(17) WLAN module
Realtek RTL8723BE-VB 802.11b/g/n 1x1 Wi-Fi + Bluetooth 4.0 combination WLAN adapter 843338-001
Intel Dual Band Wireless-AC 3168 802.11ac, Dual Band, 1×1 Wi-Fi + Bluetooth 4.0 852511-001
(18) Memory modules (PC4-17000)
8-GB 862398-850
4-GB 862397-850
(19) Solid-state drive, M.2
16 Chapter 3 Illustrated parts catalog
Item Description Spare part number
256-GB, TLC 907365-001
128-GB, TLC 907366-001
(20) Hard drive
2 TB, 5400 rpm, 9.5 mm 801808-001
1 TB, 5400 rpm, 7 mm 778192-001
500 GB, 5400 rpm, 7 mm 778186-001
500 GB, 5400 rpm, 7 mm, hybrid (8-GB SSD) 732000-001
500 GB, 7200 rpm, 7 mm 703267-001
(21) Hard drive cover
NOTE: The hard drive cover is included in the Hard Drive Hardware Kit.
906002-001
(22) Service door
NOTE: The service door is included in the Hard Drive Hardware Kit.
906002-001
(23) Optical drive
Blu-ray Disc R/RW with SuperMulti Drive 907607-001
DVD+/-RW Double-Layer SuperMulti Drive 907609-001
DVD-ROM Drive 907608-001
Computer major components 17
Cable Kit
Item Description Spare part number
Cable Kit 906000-001
(1) USB board cable
(2) TouchPad cable
(3) Power button board cable
(4) Optical drive cable
(5) Function board cable
18 Chapter 3 Illustrated parts catalog
Display components
Item Description Spare part number
(1) Display bezel
Models without an optical drive 905987-001
Models with a DVD-ROM drive 905997-001
Models with a DVD+/-RW Double-Layer SuperMulti drive 905998-001
Models with a Blu-ray Disc R/RW with SuperMulti drive 905999-001
(2) Webcam module 805139-009
Microphone module 826385-001
Display components 19
Item Description Spare part number
(3) Hinge covers (left and right) 905994-001
(4) Display/webcam cable assembly 905991-001
(5) WLAN antennas
NOTE: Included in display enclosure
not spared
(6) Display Hinge Kit, includes: 905993-001
Left hinge
Right hinge
(7) Display panel (raw)
FHD 805696-002
HD+ 810651-002
(8) Display rear cover (includes wireless antennas) 905989-001
20 Chapter 3 Illustrated parts catalog
Plastics Kit
Item Description Spare part number
Plastics Kit 906001-001
(1) Fingerprint reader insert (for use in models without a ngerprint reader)
(2) Fingerprint reader bracket
(3) Optical drive bracket
(4) Optical drive insert (for models without an optical drive)
Plastics Kit 21
Mass storage devices
Item Description Spare part number
(1) Optical drives
Blu-ray Disc R/RW with SuperMulti drive 907607-001
DVD+/-RW Double-Layer SuperMulti drive 907609-001
DVD-ROM drive 907608-001
(2) Solid-state drives, M.2
256-GB, TLC 907365-001
128-GB, TLC 907366-001
(3) Hard drives
2 TB, 5400 rpm, 9.5 mm 801808-001
1 TB, 5400 rpm, 7 mm 778192-001
500 GB, 5400 rpm, 7 mm 778186-001
500 GB, 5400 rpm, 7 mm, hybrid (8-GB SSD) 732000-001
500 GB, 7200 rpm, 7 mm 703267-001
(4) Hard drive cover
NOTE: The hard drive cover is included in the Hard Drive Hardware Kit.
906002-001
22 Chapter 3 Illustrated parts catalog
Miscellaneous parts
Description Spare part number
Smart AC adapters
65-W, 4.5 mm barrel connector 710412-001
65-W, 4.5 mm barrel connector (for use only in Asia and India 714635-850
Power cord (3-pin, C5, black, 1.83-m), for use in:
Australia 213356-001
Denmark 213353-001
Europe (Austria, Belgium, Finland, France, Germany, the Netherlands, Norway and Sweden) 213350-001
India 404827-001
Israel 398063-001
Italy 213352-001
Japan 349756-001
North America 213349-001
South Africa 361240-001
South Korea 267836-001
Switzerland 213354-001
Taiwan 393313-001
Thailand 285096-001
United Kingdom and Singapore 213351-001
Power cord (3-pin, C5, black, 1.00-m), for use in:
Australia 213356-008
Denmark 213353-008
Europe (Austria, Belgium, Finland, France, Germany, the Netherlands, Norway and Sweden) 213350-009
India 404827-003
Israel 398063-003
Italy 213352-008
Japan 349756-002
North America 213349-009
South Africa 361240-002
South Korea 267836-008
Switzerland 213354-008
Taiwan 393313-003
Thailand 285096-006
Miscellaneous parts 23
Description Spare part number
United Kingdom and Singapore 213351-008
Screw Kit 906005-001
24 Chapter 3 Illustrated parts catalog
4 Removal and replacement procedures
preliminary requirements
Tools required
You will need the following tools to complete the removal and replacement procedures:
●Flat-bladed screwdriver
●Phillips P0 and P1 screwdrivers
●Torx T8 screwdriver
Service considerations
The following sections include some of the considerations that you must keep in mind during disassembly
and assembly procedures.
NOTE: As you remove each subassembly from the computer, place the subassembly (and all accompanying
screws) away from the work area to prevent damage.
Plastic parts
CAUTION: Using excessive force during disassembly and reassembly can damage plastic parts. Use care
when handling the plastic parts. Apply pressure only at the points designated in the maintenance
instructions.
Tools required 25
Cables and connectors
CAUTION: When servicing the computer, be sure that cables are placed in their proper locations during the
reassembly process. Improper cable placement can damage the computer.
Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or seat
the cables during removal and insertion. Handle cables by the connector whenever possible. In all cases, avoid
bending, twisting, or tearing cables. Be sure that cables are routed in such a way that they cannot be caught
or snagged by parts being removed or replaced. Handle ex cables with extreme care; these cables
tear easily.
Drive handling
CAUTION: Drives are fragile components that must be handled with care. To prevent damage to the
computer, damage to a drive, or loss of information, observe these precautions:
Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the computer is
o or in Hibernation, turn the computer on, and then shut it down through the operating system.
Before handling a drive, be sure that you are discharged of static electricity. While handling a drive, avoid
touching the connector.
Before removing a diskette drive or optical drive, be sure that a diskette or disc is not in the drive and be sure
that the optical drive tray is closed.
Handle drives on surfaces covered with at least one inch of shock-proof foam.
Avoid dropping drives from any height onto any surface.
After removing a hard drive, an optical drive, or a diskette drive, place it in a static-proof bag.
Avoid exposing a hard drive to products that have magnetic elds, such as monitors or speakers.
Avoid exposing a drive to temperature extremes or liquids.
If a drive must be mailed, place the drive in a bubble pack mailer or other suitable form of protective
packaging and label the package “FRAGILE.”
26 Chapter 4 Removal and replacement procedures preliminary requirements
Grounding guidelines
Electrostatic discharge damage
Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine
the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many
cases, ESD contains enough power to alter device parameters or melt silicon junctions.
A discharge of static electricity from a nger or other conductor can destroy static-sensitive devices or
microcircuitry. Even if the spark is neither felt nor heard, damage may have occurred.
An electronic device exposed to ESD may not be aected at all and can work perfectly throughout a normal
cycle. Or the device may function normally for a while, and then degrade in the internal layers, reducing its life
expectancy.
CAUTION: To prevent damage to the computer when you are removing or installing internal components,
observe these precautions:
Keep components in their electrostatic-safe containers until you are ready to install them.
Use nonmagnetic tools.
Before touching an electronic component, discharge static electricity by using the guidelines described in this
section.
Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.
If you remove a component, place it in an electrostatic-safe container.
The following table shows how humidity aects the electrostatic voltage levels generated by dierent
activities.
CAUTION: A product can be degraded by as little as 700 V.
Typical electrostatic voltage levels
Relative humidity
Event 10% 40% 55%
Walking across carpet 35,000 V 15,000 V 7,500 V
Walking across vinyl oor 12,000 V 5,000 V 3,000 V
Motions of bench worker 6,000 V 800 V 400 V
Removing DIPS from plastic tube 2,000 V 700 V 400 V
Removing DIPS from vinyl tray 11,500 V 4,000 V 2,000 V
Removing DIPS from Styrofoam 14,500 V 5,000 V 3,500 V
Removing bubble pack from PCB 26,500 V 20,000 V 7,000 V
Packing PCBs in foam-lined box 21,000 V 11,000 V 5,000 V
Service considerations 27
Packaging and transporting guidelines
Follow these grounding guidelines when packaging and transporting equipment:
●To avoid hand contact, transport products in static-safe tubes, bags, or boxes.
●Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging.
●Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.
●Place items on a grounded surface before removing items from their containers.
●Always be properly grounded when touching a component or assembly.
●Store reusable ESD-sensitive parts from assemblies in protective packaging or nonconductive foam.
●Use transporters and conveyors made of antistatic belts and roller bushings. Be sure that mechanized
equipment used for moving materials is wired to ground and that proper materials are selected to avoid
static charging. When grounding is not possible, use an ionizer to dissipate electric charges.
Workstation guidelines
Follow these grounding workstation guidelines:
●Cover the workstation with approved static-shielding material.
●Use a wrist strap connected to a properly grounded work surface and use properly grounded tools and
equipment.
●Use conductive eld service tools, such as cutters, screwdrivers, and vacuums.
●When xtures must directly contact dissipative surfaces, use xtures made only of static-safe materials.
●Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids and
Styrofoam.
●Handle ESD-sensitive components, parts, and assemblies by the case or PCM laminate. Handle these
items only at static-free workstations.
●Avoid contact with pins, leads, or circuitry.
●Turn o power and input signals before inserting or removing connectors or test equipment.
28 Chapter 4 Removal and replacement procedures preliminary requirements
Equipment guidelines
Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation.
●When seated, wear a wrist strap connected to a grounded system. Wrist straps are exible straps with a
minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap
snugly against the skin at all times. On grounded mats with banana-plug connectors, use alligator clips
to connect a wrist strap.
●When standing, use foot straps and a grounded oor mat. Foot straps (heel, toe, or boot straps) can be
used at standing workstations and are compatible with most types of shoes or boots. On conductive
oors or dissipative oor mats, use foot straps on both feet with a minimum of one megohm resistance
between the operator and ground. To be eective, the conductive strips must be worn in contact with
the skin.
The following grounding equipment is recommended to prevent electrostatic damage:
●Antistatic tapes
●Antistatic smocks, aprons, and sleeve protectors
●Conductive bins and other assembly or soldering aids
●Nonconductive foam
●Conductive tabletop workstations with ground cords of one megohm resistance
●Static-dissipative tables or oor mats with hard ties to the ground
●Field service kits
●Static awareness labels
●Material-handling packages
●Nonconductive plastic bags, tubes, or boxes
●Metal tote boxes
●Electrostatic voltage levels and protective materials
The following table lists the shielding protection provided by antistatic bags and oor mats.
Material Use Voltage protection level
Antistatic plastic Bags 1,500 V
Carbon-loaded plastic Floor mats 7,500 V
Metallized laminate Floor mats 5,000 V
Service considerations 29
5 Removal and replacement procedures for
Customer Self-Repair parts
CAUTION: The Customer Self-Repair program is not available in all locations. Installing a part not supported
by the Customer Self-Repair program may void your warranty. Check your warranty to determine if Customer
Self-Repair is supported in your location.
NOTE: HP continually improves and changes product parts. For complete and current information on
supported parts for your computer, go to http://partsurfer.hp.com, select your country or region, and then
follow the on-screen instructions.
Component replacement procedures
NOTE: Please read and follow the procedures described here to access and replace Customer Self-Repair
parts successfully.
NOTE: Details about your computer, including model, serial number, product key, and length of warranty,
are on the service tag at the bottom of your computer. See Labels on page 14 for details.
This chapter provides removal and replacement procedures for Customer Self-Repair parts.
There are as many as 14 screws that must be removed, replaced, or loosened when servicing Customer Self-
Repair parts. Make special note of each screw size and location during removal and replacement.
Battery Safe mode
Before removing internal components, you must place the computer in “Battery Safe mode.” This mode
avoids short-circuits or system malfunction by removing power from internal components.
To place the computer in “Battery Safe mode,” follow these steps:
1. With the computer turned o and AC adapter connected, press the following key and button
combination: Windows key + Backspace key + Power button.
2. Turn the computer on to initiate “Battery Safe mode.”
3. After the computer powers o, disconnect the AC adapter.
In “Battery Safe mode,” the power button will not turn the computer on if the AC adapter is not connected.
To disengage “Battery Safe mode,” plug in the AC adapter and press the power button.
30 Chapter 5 Removal and replacement procedures for Customer Self-Repair parts
Service door
Description Spare part number
Service door
NOTE: The service door is included in the Hard Drive Hardware Kit.
906002-001
Before removing the service door, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is o or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Place the computer in “Battery Safe mode” (Battery Safe mode on page 30).
3. Disconnect all external devices connected to the computer.
4. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
Remove the service door:
1. Loosen the captive Phillips screw (1).
2. Lift the bottom of the door upward (2), and then remove the door from the computer (3).
Reverse these procedures to install the service door.
Component replacement procedures 31
Optical drive
Description Spare part number
Blu-ray Disc R/RW with SuperMulti Drive 907607-001
DVD+/-RW Double-Layer SuperMulti Drive 907609-001
DVD-ROM Drive 907608-001
Optical drive bracket
NOTE: The optical drive bracket is included in the Plastics Kit.
906001-001
Before removing the optical drive, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is o or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Place the computer in “Battery Safe mode” (Battery Safe mode on page 30).
3. Disconnect all external devices connected to the computer.
4. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
5. Remove the service door (see Service door on page 31).
Remove the optical drive:
1. Remove the Phillips PM2.5×3.0 screw (1) that secures the optical drive to the computer.
2. Insert a tool into the release slot and push the optical drive to disengage it (2).
3. Remove the optical drive from the computer (3).
32 Chapter 5 Removal and replacement procedures for Customer Self-Repair parts
4. If it is necessary to remove the bracket from the optical drive, remove the two Phillips PM2.5×3.0 screws
(1) that secure the bracket to the rear of the drive, and then remove the bracket from the drive (2).
Reverse these procedures to install a optical drive.
Component replacement procedures 33
Hard drive
Description Spare part number
Hard drives
2 TB, 5400 rpm, 9.5 mm 801808-001
1 TB, 5400 rpm, 7 mm 778192-001
500 GB, 5400 rpm, 7 mm 778186-001
500 GB, 5400 rpm, 7 mm, hybrid (8-GB SSD) 732000-001
500 GB, 7200 rpm, 7 mm 703267-001
Hard drive cover
NOTE: The hard drive cover is included in the Hard Drive Hardware Kit.
906002-001
Before removing the hard drive, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is o or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Place the computer in “Battery Safe mode” (Battery Safe mode on page 30).
3. Disconnect all external devices connected to the computer.
4. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
5. Remove the service door (see Service door on page 31).
Remove the hard drive:
1. Remove the 2 Phillips PM2.0×3.0 screws (1) that secure the hard drive to the computer.
2. Pull the plastic tab to slide the hard drive (2) away from the center of the computer to disengage it from
the connector.
34 Chapter 5 Removal and replacement procedures for Customer Self-Repair parts
3. Lift the hard drive from the bay (3).
4. To remove the hard drive cover from the hard drive, remove the 4 Phillips PM3.0×3.0 screws (1) that
secure the bracket to the drive, and then lift the cover o the drive (2).
Reverse these procedures to install a hard drive.
Component replacement procedures 35
Memory modules
Description Spare part number
4-GB (PC4-17000) 862397-850
8-GB (PC4-17000) 862398-850
Update BIOS before adding memory modules
Before adding new memory, make sure you update the computer to the latest BIOS.
CAUTION: Failure to update the computer to the latest BIOS prior to installing new memory may result in
various system problems.
To update BIOS:
1. Navigate to www.hp.com.
2. Click Support & Drivers > click Drivers & Software.
3. In the Enter a product name/number box, type the computer model information, and then click Search.
4. Click the link for the computer model.
5. Select the operating system, and then click Next.
6. Under Step 2: Select a Download, click the BIOS link.
7. Click the link for the most recent BIOS.
8. Click the Download button, and then follow the on-screen instructions.
Before removing the memory module, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is o or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Place the computer in “Battery Safe mode” (Battery Safe mode on page 30).
3. Disconnect all external devices connected to the computer.
4. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
5. Remove the service door (see Service door on page 31).
Remove the memory module:
1. Spread the retaining tabs (1) on each side of the memory module slot to release the memory module.
(The edge of the module opposite the slot rises away from the computer.)
36 Chapter 5 Removal and replacement procedures for Customer Self-Repair parts
2. Remove the memory module (2) by pulling the module away from the slot at an angle.
NOTE: Memory modules are designed with a notch to prevent incorrect insertion into the memory
module slot.
Reverse this procedure to install a memory module.
Component replacement procedures 37
WLAN/Bluetooth combo card
The computer uses a card that provides both WLAN and Bluetooth functionality.
Description Spare part number
Realtek RTL8723BE-VB 802.11b/g/n 1x1 Wi-Fi + Bluetooth 4.0 combination WLAN adapter 843338-001
Intel Dual Band Wireless-AC 3168 802.11ac, Dual Band, 1×1 Wi-Fi + Bluetooth 4.0 852511-001
Before removing the WLAN module, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is o or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Place the computer in “Battery Safe mode” (Battery Safe mode on page 30).
3. Disconnect all external devices connected to the computer.
4. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
5. Remove the service door (see Service door on page 31).
Remove the WLAN module:
1. Disconnect the WLAN antenna cables (1) from the terminals on the WLAN module.
NOTE: The WLAN antenna cable labeled “1” connects to the WLAN module “Main” terminal labeled “1”.
The WLAN antenna cable labeled “2” connects to the WLAN module “Aux” terminal labeled “2”. If the
computer is equipped with an 802.11a/b/g/n WLAN module, the yellow WLAN antenna cable connects to
the middle terminal on the WLAN module.
2. Remove the Phillips PM2.0×4.0 screw (2) that secures the WLAN module to the computer. (The edge of
the module opposite the slot rises away from the computer.)
38 Chapter 5 Removal and replacement procedures for Customer Self-Repair parts
3. Remove the WLAN module (3) by pulling the module away from the slot at an angle.
NOTE: WLAN modules are designed with a notch to prevent incorrect insertion.
NOTE: If the WLAN antennas are not connected to the terminals on the WLAN module, the protective
sleeves must be installed on the antenna connectors, as shown in the following illustration.
Reverse this procedure to install the WLAN module.
Component replacement procedures 39
M.2 solid-state drive
Description Spare part number
256-GB, TLC 907365-001
128-GB, TLC 907366-001
Before removing the solid-state drive, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is o or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Place the computer in “Battery Safe mode” (Battery Safe mode on page 30).
3. Disconnect all external devices connected to the computer.
4. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
5. Remove the service door (see Service door on page 31).
Remove the solid-state drive:
1. Remove the Phillips PM2.0×4.0 screw (1) that secures the solid-state drive to the computer. (The edge
of the module opposite the slot rises away from the computer.)
2. Remove the solid-state drive (2) by pulling the module away from the slot at an angle.
Reverse this procedure to install the solid-state drive.
40 Chapter 5 Removal and replacement procedures for Customer Self-Repair parts
Keyboard
In this section, the rst table provides the main spare part number for the keyboards. The second table
provides the country codes.
Description Spare part number
Keyboard, no backlight 827028-xxx
Keyboard, backlit 827029-xxx
For use in country
or region
Spare part
number
For use in country
or region
Spare part
number
For use in country
or region
Spare part
number
Belgium -A41 India -D61 Slovenia -BA1
Bulgaria -261 Israel -BB1 South Korea -AD1
Canada -DB1 Italy -061 Spain -071
Czech Republic
and Slovakia
-FL1 Japan -291 Switzerland -BG1
Denmark, Finland, and
Norway
-DH1 The Netherlands -B31 Taiwan -AB1
France -051 Northern Africa -FP1 Thailand -281
Germany -041 Portugal -131 Turkey -141
Greece -151 Russia -251 United Kingdom -031
Hungary -211 Saudi Arabia -171 United States -001
Iceland -DD1
Before removing the keyboard, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is o or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Place the computer in “Battery Safe mode” (Battery Safe mode on page 30).
3. Disconnect all external devices connected to the computer.
4. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
5. Remove the service door (see Service door on page 31).
Remove the keyboard:
1. Remove the 2 Phillips PM2.5×7.0 screws that secure the keyboard to the computer (1).
Component replacement procedures 41
2. Insert a tool into the access hole in the bottom of the computer (next to the hard drive bay) and push to
disengage the keyboard from the top cover (2).
3. Lift the top of the keyboard upward (1), and then rotate the keyboard until it rests on the palm rest (2).
NOTE: A cable (or cables) connect the bottom of the keyboard to the system board. Make sure not to
prematurely pull the cables out of the system board connector.
42 Chapter 5 Removal and replacement procedures for Customer Self-Repair parts
4. Disconnect the keyboard cable by lifting the connector latch (1), and then disconnect the keyboard cable
from the system board (2).
5. If applicable, disconnect the backlight cable by lifting the connector latch (3), and then disconnect the
cable from the system board (4).
6. Remove the keyboard (5).
Reverse this procedure to install the keyboard.
Component replacement procedures 43
6 Removal and replacement procedures for
Authorized Service Provider parts
CAUTION: Components described in this chapter should only be accessed by an authorized service provider.
Accessing these parts can damage the computer or void the warranty.
NOTE: HP continually improves and changes product parts. For complete and current information on
supported parts for your computer, go to http://partsurfer.hp.com, select your country or region, and then
follow the on-screen instructions.
Component replacement procedures
NOTE: Details about your computer, including model, serial number, product key, and length of warranty,
are on the service tag at the bottom of your computer. See Labels on page 14 for details.
This chapter provides removal and replacement procedures for Authorized Service Provider only parts.
There are as many as 62 screws that must be removed, replaced, or loosened when servicing Authorized
Service Provider only parts. Make special note of each screw size and location during removal and
replacement.
Display subcomponents (bezel, webcam, panel)
This section describes removing display subcomponents that do not require that you remove the entire
display assembly from the computer. You can remove the display bezel, webcam/microphone module, and
display panel while the display assembly is still attached to the computer.
To remove the remaining display subcomponents, you must remove the entire display assembly from the
computer. See Display assembly on page 76 for more information about removing the display assembly in
its entirety.
Description Spare part number
Raw display panel
FHD 805696-002
HD+ 810651-002
Display bezel
Models without an optical drive 905987-001
Models with a DVD-ROM drive 905997-001
Models with a DVD+/-RW Double-Layer SuperMulti drive 905998-001
Models with a Blu-ray Disc R/RW with SuperMulti drive 905999-001
Webcam/microphone module 805139-009
44 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
Before removing display subcomponents while the display assembly is still attached to the computer, follow
these steps:
1. Shut down the computer. If you are unsure whether the computer is o or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Place the computer in “Battery Safe mode” (Battery Safe mode on page 30).
3. Disconnect all external devices connected to the computer.
4. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
Remove the display bezel, webcam/microphone module, and raw display panel:
1. Position the computer upright with the front toward you, and then open it.
2. Remove the 2 screw covers (1) and 2 Phillips PM2.0×3.0 screws (2) that secure the bezel to the display.
3. Flex the inside of the top edge (3), left and right sides (4), and the inside of the bottom edge (5) of the
display bezel until the bezel disengages from the display enclosure.
4. Remove the display bezel (6).
5. To remove the webcam/microphone module:
a. Position the display assembly with the top edge toward you.
b. Lift to disengage the adhesive that secures the webcam/microphone module to the display (1).
Component replacement procedures 45
c. Disconnect the cable (2) from the module.
6. To remove the display panel:
a. Remove the 4 Phillips PM2.0×3.0 screws (1) that secure the display panel to the enclosure.
b. Rotate the display panel onto the keyboard (2) to gain access to the display cable connection on
the back of the panel.
c. On the back of the display panel, release the adhesive strip that secures the display panel cable to
the display panel (1), and then disconnect the cable (2).
46 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
d. Remove the display panel from the computer (3).
Reverse this procedure to reassemble and install the display bezel, webcam/microphone module, and display
panel.
Component replacement procedures 47
Top cover
NOTE: Top cover spare part kits include the touchpad assembly.
Description Spare part number
Top cover (includes touchpad) 905996-001
Before removing the top cover, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is o or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Place the computer in “Battery Safe mode” (Battery Safe mode on page 30).
3. Disconnect all external devices connected to the computer.
4. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
5. Remove the following components:
a. Service door (see Service door on page 31).
b. Hard drive (Hard drive on page 34)
c. Optical drive (Optical drive on page 32)
d. Keyboard (see Keyboard on page 41)
Remove the top cover:
1. Position the computer upside-down with the front toward you.
2. Remove the 13 Torx T8 2.5×6.0 screws (1) that secure the top cover to the computer.
3. Remove the 4 Phillips PM2.0×3.0 screws (2) that secure the top cover to the computer.
4. Position the computer upright and open it as far as possible.
48 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
5. Remove the 4 Torx T8 2.5×6.0 screws that secure the top cover to the computer.
Component replacement procedures 49
6. Disconnect the following cables from the system board:
(1) Speaker cable
(2) Function board cable
(3) Power button board cable
(4) Touchpad board cable
(5) Fingerprint reader cable
(6) USB board
50 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
7. Rotate the bottom of the top cover upward (1), and then lift the top cover o the computer (2).
Reverse this procedure to install the top cover.
Component replacement procedures 51
Fingerprint reader assembly
Description Spare part number
Fingerprint reader assembly (includes cable) 906003-001
Fingerprint reader bracket
NOTE: The ngerprint reader bracket is included in the Plastics Kit.
906001-001
Fingerprint reader insert (for use in models without a ngerprint reader)
NOTE: The ngerprint reader insert is included in the Plastics Kit.
906001-001
Before removing the ngerprint reader assembly, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is o or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Place the computer in “Battery Safe mode” (Battery Safe mode on page 30).
3. Disconnect all external devices connected to the computer.
4. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
5. Remove the following components:
a. Service door (see Service door on page 31).
b. Optical drive (Optical drive on page 32)
c. Hard drive (Hard drive on page 34)
d. Keyboard (see Keyboard on page 41)
e. Top cover (see Top cover on page 48)
Remove the ngerprint reader assembly:
1. Position the top cover upside-down.
2. Slide the bracket downward and lift it o the ngerprint reader board (1). To slide the bracket
downward, use a at tool and push at the top of the bracket to force it downward.
3. Remove the cable from the clips along the cable routing path in the top cover (2).
52 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
4. Lift the ngerprint reader cable to disengage the adhesive that secures it to the top cover (3), and then
remove the board and cable assembly from the top cover (4).
Reverse this procedure to install the ngerprint reader assembly.
Component replacement procedures 53
Power button board
Description Spare part number
Power button board assembly 905754-001
Power button board cable (included in Cable Kit) 906000-001
Before removing the power button board, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is o or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Place the computer in “Battery Safe mode” (Battery Safe mode on page 30).
3. Disconnect all external devices connected to the computer.
4. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
5. Remove the following components:
a. Service door (see Service door on page 31)
b. Optical drive (Optical drive on page 32)
c. Hard drive (Hard drive on page 34)
d. Keyboard (see Keyboard on page 41)
e. Top cover (see Top cover on page 48)
Remove the power button board:
1. Position the top cover upside-down.
2. Disconnect the cable from the connector on the board (1).
3. Remove the Phillips PM2.0×3.0 screw (2) that secures the board to the top cover.
4. Lift the left side of the board (3), and then pull the board out and to the left to remove it from under the
tabs (4).
54 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
5. If you need to replace the cable, note the cable routing path through the top cover (5).
Reverse this procedure to install the power button board.
Component replacement procedures 55
Function board
Description Spare part number
Function board 910959-001
Function board cable (included in Cable Kit) 906000-001
Before removing the function board, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is o or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Place the computer in “Battery Safe mode” (Battery Safe mode on page 30).
3. Disconnect all external devices connected to the computer.
4. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
5. Remove the following components:
a. Service door (see Service door on page 31)
b. Optical drive (Optical drive on page 32)
c. Hard drive (Hard drive on page 34)
d. Keyboard (see Keyboard on page 41)
e. Top cover (see Top cover on page 48)
Remove the function board:
1. Position the top cover upside-down.
2. Disconnect the cable from the connector on the function board (1).
3. Remove the Phillips PM2.0×3.0 screw (2) that secures the board to the top cover.
4. Lift the left side of the board (3), and then slide the board to the left to remove it from the top cover (4).
56 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
5. If you need to replace the function board cable, note how it is routed in the top cover (5).
Reverse this procedure to install the function board.
Component replacement procedures 57
Speaker assembly
Description Spare part number
Speaker assembly 906004-001
Before removing the speaker assembly, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is o or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Place the computer in “Battery Safe mode” (Battery Safe mode on page 30).
3. Disconnect all external devices connected to the computer.
4. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
5. Remove the following components:
a. Service door (see Service door on page 31).
b. Optical drive (Optical drive on page 32)
c. Hard drive (Hard drive on page 34)
d. Keyboard (see Keyboard on page 41)
e. Top cover (see Top cover on page 48)
Remove the speaker assembly:
1. Position the top cover upside-down.
2. Remove the 2 Phillips PM2.0×3.0 screws (1) that secure the speaker assembly to the top cover.
3. Remove the cable from the clips in the top cover (2).
58 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
4. Remove the speakers from the top cover (3).
Reverse this procedure to install the speaker assembly.
Component replacement procedures 59
TouchPad assembly
Description Spare part number
TouchPad assembly
NOTE: The TouchPad is included in the Top Cover spare part kit.
not spared
TouchPad assembly cable (included in Cable Kit) 906000-001
Before removing the TouchPad assembly, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is o or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Place the computer in “Battery Safe mode” (Battery Safe mode on page 30).
3. Disconnect all external devices connected to the computer.
4. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
5. Remove the following components:
a. Service door (see Service door on page 31).
b. Optical drive (Optical drive on page 32)
c. Hard drive (Hard drive on page 34)
d. Keyboard (see Keyboard on page 41)
e. Top cover (see Top cover on page 48)
Remove the TouchPad assembly:
NOTE: Before you remove the TouchPad assembly, make sure nothing (memory card or plastic insert) in
installed.
1. Position the top cover upside-down.
2. Remove the 4 Phillips PM2.5×3.0 screws (1) that secure the TouchPad to the top cover.
3. Disconnect the cable from the connector on the TouchPad (2).
4. Rotate the top of the TouchPad upward (3), and then pull the board toward the top of the top cover to
remove it (4).
60 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
5. If you need to replace the TouchPad assembly cable, note how it is routed in the top cover (5).
Reverse this procedure to install the TouchPad assembly.
Component replacement procedures 61
Battery
Description Spare part number
Battery, 4-cell, 48 WHr, 4.21 Ah 851610-855
Before removing the battery, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is o or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Place the computer in “Battery Safe mode” (Battery Safe mode on page 30).
3. Disconnect all external devices connected to the computer.
4. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
5. Remove the following components:
a. Service door (see Service door on page 31).
b. Optical drive (Optical drive on page 32)
c. Hard drive (Hard drive on page 34)
d. Keyboard (see Keyboard on page 41)
e. Top cover (see Top cover on page 48)
Remove the battery:
CAUTION: Removing a battery that is the sole power source for the computer can cause loss of information.
To prevent loss of information, save your work and shut down the computer through Windows before
removing the battery.
1. Position the computer upright on a at surface.
2. Remove the 2 Torx T8 2.5×7.0 screws (1) that secure the battery to the computer.
62 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
3. Lift the battery out of the computer (2).
Reverse this procedure to install the battery.
Component replacement procedures 63
USB/audio board
Description Spare part number
USB/audio board 905755-001
USB/audio board cable (included in Cable Kit) 906000-001
Before removing the USB/audio board, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is o or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
4. Remove the following components:
a. Service door (see Service door on page 31).
b. Optical drive (Optical drive on page 32)
c. Hard drive (Hard drive on page 34)
d. Keyboard (see Keyboard on page 41)
e. Top cover (see Top cover on page 48)
f. Battery (see Battery on page 62)
Remove the USB/audio board:
1. Position the computer upright on a at surface.
2. Disconnect the cable from the board (1).
3. Remove the Phillips PM2.5×6.0 screw (2) that secures the board to the computer.
64 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
4. Lift the board out of the computer (3).
Reverse this procedure to install the USB/audio board.
Component replacement procedures 65
Fan
Description Spare part number
Fan 905774-001
NOTE: To properly ventilate the computer, allow at least 7.6 cm (3.0 in) of clearance on the left side of the
computer. The computer uses an electric fan for ventilation. The fan is controlled by a temperature sensor and
is designed to turn on automatically when high temperature conditions exist. These conditions are aected by
high external temperatures, system power consumption, power management/battery conservation
congurations, battery fast charging, and software requirements. Exhaust air is displaced through the
ventilation grill located on the left side of the computer.
Before removing the fan/heat sink assembly, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is o or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the battery (see Battery on page 62), and then remove the following components:
a. Service door (see Service door on page 31).
b. Hard drive (Hard drive on page 34)
c. Optical drive (Optical drive on page 32)
d. Keyboard (see Keyboard on page 41)
e. Top cover (see Top cover on page 48)
f. Battery (see Battery on page 62)
Remove the fan:
1. Position the computer upright on a at surface.
2. Disconnect the fan cable (1) from the system board.
3. Remove the cable from the clip on the side of the fan (2).
4. Remove the Phillips PM2.5×7.0 screw (3) that secures the fan to the computer.
66 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
5. Lift the fan from the computer (4).
Reverse this procedure to install the fan.
Component replacement procedures 67
Optical drive connector cable
Description Spare part number
Cable Kit
The optical drive connector cable is included in the Cable Kit.
906000-001
Before removing the optical drive connector cable, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is o or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
4. Remove the following components:
a. Service door (see Service door on page 31).
b. Optical drive (Optical drive on page 32)
c. Hard drive (Hard drive on page 34)
d. Keyboard (see Keyboard on page 41)
e. Top cover (see Top cover on page 48)
f. Battery (see Battery on page 62)
Remove the optical drive connector cable:
1. Position the computer upright on a at surface.
2. Disconnect the optical drive connector cable from the system board (1).
3. Remove the cable from the clips built into the computer (2).
68 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
4. Remove the connector from the computer (3).
Reverse this procedure to install the optical drive connector cable.
Component replacement procedures 69
System board
NOTE: All system board spare part kits include replacement thermal material.
All system boards use the following part numbers:
xxxxxx-001: Non-Windows operating systems
xxxxxx-601: Windows 10 operating system
Description Spare part number
System board with processor:
Intel Core i7-7500U processor; 2-GB discrete graphics memory 907715-xxx
Intel Core i5-7200U processor; 2-GB discrete graphics memory 907714-xxx
Intel Core i3-7100U processor; 2-GB discrete graphics memory 907713-xxx
Before removing the system board, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is o or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
4. Remove the following components:
a. Service door (see Service door on page 31).
b. Hard drive (see Hard drive on page 34)
c. Optical drive (Optical drive on page 32)
d. Keyboard (see Keyboard on page 41)
e. Top cover (see Top cover on page 48)
f. Battery (see Battery on page 62)
When replacing the system board, be sure to remove the following components (as applicable) from the
defective system board and install on the replacement system board:
●Memory modules (see Memory modules on page 36)
●WLAN/Bluetooth module (see WLAN/Bluetooth combo card on page 38)
●M.2 solid-state drive (see M.2 solid-state drive on page 40)
●Heat sink (see Heat sink assembly on page 74)
Remove the system board:
1. Position the computer upright on a at surface.
70 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
2. Disconnect the following cables from the system board:
(1) Display cable
(2) Optical drive connector cable
3. Remove the 3 Phillips PM2.5×7.0 screws (1) that secure the system board to the computer.
4. Lift the bracket from atop the USB-Type C port (2).
5. Rotate the right side of the system board upward (3).
6. Disconnect the power connector cable from the bottom of the system board (4).
Component replacement procedures 71
7. Pull the system board away from the connectors on the side of the chassis to remove it from the
computer (5).
Reverse this procedure to install the system board.
72 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
RTC battery
Description Spare part number
RTC battery not spared
Before removing the RTC battery, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is o or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
4. Remove the following components:
a. Service door (see Service door on page 31).
b. Hard drive (see Hard drive on page 34)
c. Optical drive (Optical drive on page 32)
d. Keyboard (see Keyboard on page 41)
e. Top cover (see Top cover on page 48)
f. Battery (see Battery on page 62)
g. System board (see System board on page 70)
Remove the RTC battery:
1. Position the system board upside-down.
2. Use a tool to pry the battery out of the socket (1).
3. Remove the battery from the system board (2).
Reverse this procedure to install the RTC battery.
Component replacement procedures 73
Heat sink assembly
All heat sink assembly spare part kits include replacement thermal material.
Description Spare part number
Heat sink 907364-001
Before removing the heat sink assembly, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is o or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
4. Remove the following components:
a. Service door (see Service door on page 31).
b. Hard drive (see Hard drive on page 34)
c. Optical drive (Optical drive on page 32)
d. WLAN module (see WLAN/Bluetooth combo card on page 38)
e. Keyboard (see Keyboard on page 41)
f. Top cover (see Top cover on page 48)
g. Battery (see Battery on page 62)
h. System board (see System board on page 70)
Remove the heat sink assembly:
1. Position the system board upside-down.
2. In the order indicated on the heat sink, loosen the 6 captive Phillips screws (1)–(6) that secure the heat
sink to the system board.
74 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
3. Lift the heat sink from the system board (7).
NOTE: Thoroughly clean thermal material from the surfaces of the system board components (1)(3)
and the heat sink (2)(4) each time you remove the heat sink. All heat sink and processor spare part kits
include thermal material.
Reverse this procedure to install the heat sink assembly.
Component replacement procedures 75
Display assembly
This section describes removing components that require you to completely remove the display panel. For
more information about removing display components that do not require that you remove the assembly
from the computer, see Display subcomponents (bezel, webcam, panel) on page 44.
NOTE: The display assembly is spared at the subcomponent level only.
Before removing the display assembly, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is o or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
4. Remove the following components:
a. Service door (see Service door on page 31).
b. Hard drive (see Hard drive on page 34)
c. Optical drive (Optical drive on page 32)
d. WLAN module (see WLAN/Bluetooth combo card on page 38)
e. Keyboard (see Keyboard on page 41)
f. Top cover (see Top cover on page 48)
g. Battery (see Battery on page 62)
Remove the display assembly:
1. Position the computer upright on a at surface.
2. Disconnect the display cable from the system board (1).
3. Pull the WLAN antennas through the hole in the computer (2).
4. Remove the 5 Phillips PM2.5×7.0 screws (3) from the display hinges.
76 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
5. Lift the display assembly straight up and remove it (4).
CAUTION: When installing the display assembly, be sure that the wireless antenna cables are routed
and arranged properly. Failure to properly route the antennas can result in degradation of the
computer's wireless performance.
6. To remove the display bezel, remove the 2 screw covers (1) and the 2 Phillips PM2.0×3.0 screws (2) from
the bottom corners of the display bezel.
7. Flex the top (3) of the bezel, the inside edges of the left and right sides (4), and then the bottom (5) of
the bezel until it disengages from the display enclosure.
Component replacement procedures 77
8. Remove the display bezel (6).
The display bezel is available using the following spare part numbers:
905987-001: Models without an optical drive
905997-001: Models with a DVD-ROM drive
905998-001: Models with a DVD+/-RW Double-Layer SuperMulti drive
905999-001: Models with a Blu-ray Disc R/RW with SuperMulti drive
NOTE: The display will not be connected to the computer as shown in the following image.
78 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
9. If it is necessary to replace the webcam or microphone module, gently pull the module away from the
double-sided tape on the display enclosure (1), and then disconnect the cable from the module (2).
The webcam module is available using spare part number 805139-009.
10. If it is necessary to remove or replace the display panel, remove the 4 Phillips PM2.0×3.0 screws (1) that
secure the display panel to the enclosure.
11. Rotate the display panel onto the keyboard (2) to gain access to the display cable connection on the
back of the panel.
Component replacement procedures 79
12. On the back of the display panel, release the adhesive strip that secures the display panel cable to the
display panel (1), and then disconnect the cable (2).
13. Remove the display panel from the display enclosure (3).
Raw display panels are available using spare part number 810651-002 for HD+ panels and 805696-002
for FHD panels.
14. If it is necessary to remove or replace the hinge covers, remove the 2 Phillips PM2.0×3.0 screws (1) that
secure the hinge covers to the display enclosure.
80 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
15. Remove the hinge covers from the display hinges (2).
Display hinge covers are available using spare part number 905994-001.
16. If it is necessary to remove or replace the display hinges, remove the 4 Phillips PM2.5×2.5 screws (1)
that secure both display hinges to the display enclosure.
17. Remove the display hinges from the display enclosure (2).
Display hinges are available in the Display Hinge Kit using spare part number 905993-001.
18. If it is necessary to replace the display/webcam cable, remove the webcam cable from the clips in the
display enclosure (1), and the clips at the bottom of the display enclosure (2).
Component replacement procedures 81
19. Remove the cable from the display enclosure (3).
The display/webcam cable is available using spare part number 905991-001.
The display enclosure is available using spare part number 905989-001.
Reverse this procedure to reassemble and install the display assembly.
82 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
Power connector and cable
Description Spare part number
Power connector and cable 828949-007
Before removing the power cable, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is o or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
4. Remove the following components:
a. Service door (see Service door on page 31).
b. Optical drive (Optical drive on page 32)
c. Hard drive (Hard drive on page 34)
d. Keyboard (see Keyboard on page 41)
e. Top cover (see Top cover on page 48)
f. Battery (see Battery on page 62)
g. Display assembly (see Display assembly on page 76)
Remove the power cable:
1. Remove the cable from the clips in the computer (1).
2. Remove the power cable from the computer (2).
Reverse this procedure to install the power cable.
Component replacement procedures 83
7 Computer Setup (BIOS), TPM, and HP Sure
Start
Using Computer Setup
Computer Setup, or Basic Input/Output System (BIOS), controls communication between all the input and
output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Computer Setup
includes settings for the types of devices installed, the startup sequence of the computer, and the amount of
system and extended memory.
NOTE: Use extreme care when making changes in Computer Setup. Errors can prevent the computer from
operating properly.
Starting Computer Setup
NOTE: An external keyboard or mouse connected to a USB port can be used with Computer Setup only if USB
legacy support is enabled.
▲Turn on or restart the computer, and when the HP logo appears, press f10 to enter Computer Setup.
Navigating and selecting in Computer Setup
●To select a menu or a menu item, use the tab key and the keyboard arrow keys and then press enter, or
use a pointing device to select the item.
●To scroll up and down, select the up arrow or the down arrow in the upper-right corner of the screen, or
use the up arrow key or the down arrow key on the keyboard.
●To close open dialog boxes and return to the main Computer Setup screen, press esc, and then follow
the on-screen instructions.
To exit Computer Setup menus, choose one of the following methods:
●To exit Computer Setup menus without saving your changes:
Select the Exit icon in the lower-right corner of the screen, and then follow the on-screen instructions.
– or –
Select Main, select Ignore Changes and Exit, and then press enter.
●To save your changes and exit Computer Setup menus:
Select the Save icon in the lower-right corner of the screen, and then follow the on-screen instructions.
– or –
Select Main, select Save Changes and Exit, and then press enter.
Your changes go into eect when the computer restarts.
Restoring factory settings in Computer Setup
NOTE: Restoring defaults will not change the hard drive mode.
84 Chapter 7 Computer Setup (BIOS), TPM, and HP Sure Start
To return all settings in Computer Setup to the values that were set at the factory, follow these steps:
1. Start Computer Setup. See Starting Computer Setup on page 84.
2. Select Main, and then select Apply Factory Defaults and Exit.
NOTE: On select products, the selections may display Restore Defaults instead of Apply Factory
Defaults and Exit.
3. Follow the on-screen instructions.
4. To save your changes and exit, select the Save icon in the lower-right corner of the screen, and then
follow the on-screen instructions.
– or –
Select Main, select Save Changes and Exit, and then press enter.
Your changes go into eect when the computer restarts.
NOTE: Your password settings and security settings are not changed when you restore the factory settings.
Updating the BIOS
Updated versions of the BIOS may be available on the HP website.
Most BIOS updates on the HP website are packaged in compressed les called SoftPaqs.
Some download packages contain a le named Readme.txt, which contains information regarding installing
and troubleshooting the le.
Determining the BIOS version
To decide whether you need to update Computer Setup (BIOS), rst determine the BIOS version on your
computer.
BIOS version information (also known as ROM date and System BIOS) can be accessed by pressing fn+esc (if
you are already in Windows) or by using Computer Setup.
1. Start Computer Setup. See Starting Computer Setup on page 84.
2. Select Main, and then select System Information.
3. To exit Computer Setup without saving your changes, select the Exit icon in the lower-right corner of the
screen, and then follow the on-screen instructions.
– or –
Select Main, select Ignore Changes and Exit, and then press enter.
To check for later BIOS versions, see Downloading a BIOS update on page 86.
Using Computer Setup 85
Downloading a BIOS update
CAUTION: To reduce the risk of damage to the computer or an unsuccessful installation, download and
install a BIOS update only when the computer is connected to reliable external power using the AC adapter. Do
not download or install a BIOS update while the computer is running on battery power, docked in an optional
docking device, or connected to an optional power source. During the download and installation, follow these
instructions:
Do not disconnect power on the computer by unplugging the power cord from the AC outlet.
Do not shut down the computer or initiate Sleep.
Do not insert, remove, connect, or disconnect any device, cable, or cord.
1. Type support in the taskbar search box, and then select the HP Support Assistant app.
– or –
Select the question mark icon in the taskbar.
2. Select Updates, and then select Check for updates and messages.
3. Follow the on-screen instructions.
4. At the download area, follow these steps:
a. Identify the most recent BIOS update and compare it to the BIOS version currently installed on your
computer. Make a note of the date, name, or other identier. You may need this information to
locate the update later, after it has been downloaded to your hard drive.
b. Follow the on-screen instructions to download your selection to the hard drive.
Make a note of the path to the location on your hard drive where the BIOS update is downloaded.
You will need to access this path when you are ready to install the update.
NOTE: If you connect your computer to a network, consult the network administrator before installing
any software updates, especially system BIOS updates.
BIOS installation procedures vary. Follow any instructions that are revealed on the screen after the download
is complete. If no instructions are revealed, follow these steps:
1. Type file in the taskbar search box, and then select File Explorer.
2. Select your hard drive designation. The hard drive designation is typically Local Disk (C:).
3. Using the hard drive path you recorded earlier, open the folder that contains the update.
4. Double-click the le that has an .exe extension (for example, lename.exe).
The BIOS installation begins.
5. Complete the installation by following the on-screen instructions.
NOTE: After a message on the screen reports a successful installation, you can delete the downloaded le
from your hard drive.
Changing the boot order using the f9 prompt
To dynamically choose a boot device for the current startup sequence, follow these steps:
1. Access the Boot Device Options menu:
86 Chapter 7 Computer Setup (BIOS), TPM, and HP Sure Start
●Turn on or restart the computer, and when the HP logo appears, press f9 to enter the Boot Device
Options menu.
2. Select a boot device, then press enter.
TPM BIOS settings (select products only)
IMPORTANT: Before enabling Trusted Platform Module (TPM) functionality on this system, you must ensure
that your intended use of TPM complies with relevant local laws, regulations and policies, and approvals or
licenses must be obtained if applicable. For any compliance issues arising from your operation/usage of TPM
which violates the above mentioned requirement, you shall bear all the liabilities wholly and solely. HP will
not be responsible for any related liabilities.
TPM provides additional security for your computer. You can modify the TPM settings in Computer Setup
(BIOS).
NOTE: If you change the TPM setting to Hidden, TPM is not visible in the operating system.
To access TPM settings in Computer Setup:
1. Start Computer Setup. See Starting Computer Setup on page 84.
2. Select Security, select TPM Embedded Security, and then follow the on-screen instructions.
Using HP Sure Start (select products only)
Select computer models are congured with HP Sure Start, a technology that monitors the computer's BIOS
for attacks or corruption. If the BIOS becomes corrupted or is attacked, HP Sure Start automatically restores
the BIOS to its previously safe state, without user intervention.
HP Sure Start is congured and already enabled so that most users can use the HP Sure Start default
conguration. The default conguration can be customized by advanced users.
To access the latest documentation on HP Sure Start, go to http://www.hp.com/support. Select Find your
product, and then follow the on-screen instructions.
TPM BIOS settings (select products only) 87
8 Using HP PC Hardware Diagnostics (UEFI)
HP PC Hardware Diagnostics is a Unied Extensible Firmware Interface (UEFI) that allows you to run diagnostic
tests to determine whether the computer hardware is functioning properly. The tool runs outside the
operating system so that it can isolate hardware failures from issues that are caused by the operating system
or other software components.
When HP PC Hardware Diagnostics (UEFI) detects a failure that requires hardware replacement, a 24-digit
Failure ID code is generated. This ID code can then be provided to support to help determine how to correct
the problem.
NOTE: To start diagnostics on a convertible computer, your computer must be in notebook mode and you
must use the keyboard attached.
To start HP PC Hardware Diagnostics (UEFI), follow these steps:
1. Turn on or restart the computer, and quickly press esc.
2. Press f2.
The BIOS searches three places for the diagnostic tools, in the following order:
a. Connected USB drive
NOTE: To download the HP PC Hardware Diagnostics (UEFI) tool to a USB drive, see Downloading
HP PC Hardware Diagnostics (UEFI) to a USB device on page 88.
b. Hard drive
c. BIOS
3. When the diagnostic tool opens, select the type of diagnostic test you want to run, and then follow the
on-screen instructions.
NOTE: If you need to stop a diagnostic test, press esc.
Downloading HP PC Hardware Diagnostics (UEFI) to a USB device
NOTE: The HP PC Hardware Diagnostics (UEFI) download instructions are provided in English only, and you
must use a Windows computer to download and create the HP UEFI support environment because only .exe
les are oered.
There are two options to download HP PC Hardware Diagnostics to a USB device.
Download the latest UEFI version
1. Go to http://www.hp.com/go/techcenter/pcdiags. The HP PC Diagnostics home page is displayed.
2. In the HP PC Hardware Diagnostics section, select the Download link, and then select Run.
Download any version of UEFI for a specic product
1. Go to http://www.hp.com/support.
2. Select Get software and drivers.
88 Chapter 8 Using HP PC Hardware Diagnostics (UEFI)
3. Enter the product name or number.
– or –
Select Identify now to let HP automatically detect your product.
4. Select your computer, and then select your operating system.
5. In the Diagnostic section, follow the on-screen instructions to select and download the UEFI version
you want.
Additional BIOS crisis recovery tool
HP provides a BIOS crisis recovery tool through the HP PC Hardware Diagnostics 3-in-1 USB key. This tool can
be used by HP authorized service providers to recover systems that have failed due to a corrupted BIOS. For
more information about using the 3-in-1 USB key for BIOS crisis recovery, go to http://www.hp.com/go/
techcenter/pcdiags. Additional information is included in the web-based training oered by HP University. See
the modules that cover HP PC Hardware Diagnostics (UEFI).
Blink and beep codes
Some system errors prevent the use of the video screen; instead, the system provides error information
through blink codes using lights. The codes are presented in a sequence. Audible long and short beeps
accompany blinks, respectively. The following table describes the meaning of critical blink codes.
Num lock
light Battery light Description
2 The main area (DXE) of BIOS has become corrupted and there is no recovery binary image
available.
8 The embedded controller policy requires the user to enter a key sequence (SureStart 2.0).
White and amber blinking The embedded controller is recovering the boot block or DXE. It takes about 10 seconds
to load the DXE image and get video in the DXE case.
3 The embedded controller has timed out waiting for BIOS to return from memory
initialization.
4 The embedded controller has timed out waiting for BIOS to return from graphics
initialization.
5 The system board displays a power failure (crowbar).
The processor is not detected.
The processor does not support an enabled feature (typically this applies only to TXT).
7 1 The embedded controller cannot nd valid rmware.
Blink and beep codes 89
9 Backup and recovery
This chapter provides information about the following processes. The information in the chapter is standard
procedure for most products.
●Creating recovery media and backups
●Restoring and recovering your system
For additional information, refer to the HP support assistant app.
▲Type support in the taskbar search box, and then select the HP Support Assistant app.
‒ or –
Click the question mark icon in the taskbar.
IMPORTANT: If you will be performing recovery procedures on a tablet, the tablet battery must be at least
70% charged before you start the recovery process.
IMPORTANT: For a tablet with a detachable keyboard, connect the keyboard to the keyboard dock before
beginning any recovery process.
Creating recovery media and backups
The following methods of creating recovery media and backups are available on select products only. Choose
the available method according to your computer model.
●Use HP Recovery Manager to create HP Recovery media after you successfully set up the computer. This
step creates a backup of the HP Recovery partition on the computer. The backup can be used to reinstall
the original operating system in cases where the hard drive is corrupted or has been replaced. For
information on creating recovery media, see Creating HP Recovery media (select products only)
on page 90. For information on the recovery options that are available using the recovery media, see
Using Windows tools on page 91.
●Use Windows tools to create system restore points and create backups of personal information.
For more information, see Recovering using HP Recovery Manager on page 92.
NOTE: If storage is 32 GB or less, Microsoft System Restore is disabled by default.
Creating HP Recovery media (select products only)
If possible, check for the presence of the Recovery partition and the Windows partition. From the Start menu,
select File Explorer, and then select This PC.
●If your computer does not list the Windows partition and the Recovery partition, you can obtain recovery
media for your system from support. See the Worldwide Telephone Numbers booklet included with the
computer. You can also nd contact information on the HP website. Go to http://www.hp.com/support,
select your country or region, and follow the on-screen instructions.
90 Chapter 9 Backup and recovery
You can use Windows tools to create system restore points and create backups of personal information,
see Using Windows tools on page 91.
●If your computer does list the Recovery partition and the Windows partition, you can use HP Recovery
Manager to create recovery media after you successfully set up the computer. HP Recovery media can be
used to perform system recovery if the hard drive becomes corrupted. System recovery reinstalls the
original operating system and software programs that were installed at the factory and then congures
the settings for the programs. HP Recovery media can also be used to customize the system or restore
the factory image if you replace the hard drive.
—Only one set of recovery media can be created. Handle these recovery tools carefully, and keep
them in a safe place.
—HP Recovery Manager examines the computer and determines the required storage capacity for
the media that will be required.
—To create recovery discs, your computer must have an optical drive with DVD writer capability, and
you must use only high-quality blank DVD-R, DVD+R, DVD-R DL, or DVD+R DL discs. Do not use
rewritable discs such as CD±RW, DVD±RW, double-layer DVD±RW, or BD-RE (rewritable Blu-ray)
discs; they are not compatible with HP Recovery Manager software. Or, instead, you can use a high-
quality blank USB ash drive.
—If your computer does not include an integrated optical drive with DVD writer capability, but you
would like to create DVD recovery media, you can use an external optical drive (purchased
separately) to create recovery discs. If you use an external optical drive, it must be connected
directly to a USB port on the computer; the drive cannot be connected to a USB port on an external
device, such as a USB hub. If you cannot create DVD media yourself, you can obtain recovery discs
for your computer from HP. See the Worldwide Telephone Numbers booklet included with the
computer. You can also nd contact information on the HP website. Go to http://www.hp.com/
support, select your country or region, and follow the on-screen instructions.
—Be sure that the computer is connected to AC power before you begin creating the recovery media.
—The creation process can take an hour or more. Do not interrupt the creation process.
—If necessary, you can exit the program before you have nished creating all of the recovery DVDs.
HP Recovery Manager will nish burning the current DVD. The next time you start HP Recovery
Manager, you will be prompted to continue.
To create HP Recovery media:
IMPORTANT: For a tablet with a detachable keyboard, connect the keyboard to the keyboard dock before
beginning these steps.
1. Type recovery in the taskbar search box, and then select HP Recovery Manager.
2. Select Create recovery media, and then follow the on-screen instructions.
If you ever need to recover the system, see Recovering using HP Recovery Manager on page 92.
Using Windows tools
You can create recovery media, system restore points, and backups of personal information using Windows
tools.
NOTE: If storage is 32 GB or less, Microsoft System Restore is disabled by default.
For more information and steps, see the Get started app.
▲Select the Start button, and then select the Get started app.
Using Windows tools 91
Restore and recovery
There are several options for recovering your system. Choose the method that best matches your situation
and level of expertise:
IMPORTANT: Not all methods are available on all products.
●Windows oers several options for restoring from backup, refreshing the computer, and resetting the
computer to its original state. For more information see the Get started app.
▲Select the Start button, and then select the Get started app.
●If you need to correct a problem with a preinstalled application or driver, use the Reinstall drivers and/or
applications option (select products only) of HP Recovery Manager to reinstall the individual application
or driver.
▲Type recovery in the taskbar search box, select HP Recovery Manager, select Reinstall drivers
and/or applications, and then follow the on-screen instructions.
●If you want to recover the Windows partition to original factory content, you can choose the System
Recovery option from the HP Recovery partition (select products only) or use the HP Recovery media.
For more information, see Recovering using HP Recovery Manager on page 92. If you have not already
created recovery media, see Creating HP Recovery media (select products only) on page 90.
●On select products, if you want to recover the computer's original factory partition and content, or if you
have replaced the hard drive, you can use the Factory Reset option of HP Recovery media. For more
information, see Recovering using HP Recovery Manager on page 92.
●On select products, if you want to remove the recovery partition to reclaim hard drive space, HP
Recovery Manager oers the Remove Recovery Partition option.
For more information, see Removing the HP Recovery partition (select products only) on page 95.
Recovering using HP Recovery Manager
HP Recovery Manager software allows you to recover the computer to its original factory state by using the
HP Recovery media that you either created or that you obtained from HP, or by using the HP Recovery
partition (select products only). If you have not already created recovery media, see Creating HP Recovery
media (select products only) on page 90.
What you need to know before you get started
●HP Recovery Manager recovers only software that was installed at the factory. For software not provided
with this computer, you must either download the software from the manufacturer's website or reinstall
the software from the media provided by the manufacturer.
IMPORTANT: Recovery through HP Recovery Manager should be used as a nal attempt to correct
computer issues.
●HP Recovery media must be used if the computer hard drive fails. If you have not already created
recovery media, see Creating HP Recovery media (select products only) on page 90.
●To use the Factory Reset option (select products only), you must use HP Recovery media. If you have not
already created recovery media, see Creating HP Recovery media (select products only) on page 90.
●If your computer does not allow the creation of HP Recovery media or if the HP Recovery media does not
work, you can obtain recovery media for your system from support. See the Worldwide Telephone
Numbers booklet included with the computer. You can also nd contact information from the HP
92 Chapter 9 Backup and recovery
website. Go to http://www.hp.com/support, select your country or region, and follow the on-screen
instructions.
IMPORTANT: HP Recovery Manager does not automatically provide backups of your personal data. Before
beginning recovery, back up any personal data you want to retain.
Using HP Recovery media, you can choose from one of the following recovery options:
NOTE: Only the options available for your computer display when you start the recovery process.
●System Recovery—Reinstalls the original operating system, and then congures the settings for the
programs that were installed at the factory.
●Factory Reset—Restores the computer to its original factory state by deleting all information from the
hard drive and re-creating the partitions. Then it reinstalls the operating system and the software that
was installed at the factory.
The HP Recovery partition (select products only) allows System Recovery only.
Using the HP Recovery partition (select products only)
The HP Recovery partition allows you to perform a system recovery without the need for recovery discs or a
recovery USB ash drive. This type of recovery can be used only if the hard drive is still working.
To start HP Recovery Manager from the HP Recovery partition:
IMPORTANT: For a tablet with a detachable keyboard, connect the keyboard to the keyboard dock before
beginning these steps (select products only).
1. Type recovery in the taskbar search box, select Recovery Manager, and then select HP Recovery
Environment.
- or-
For computers or tablets with keyboards attached, press f11 while the computer boots, or press and
hold f11 as you press the power button.
For tablets without keyboards:
Turn on or restart the tablet, and then quickly hold down the volume up button; then select f11.
- or -
Turn on or restart the tablet, and then quickly hold down the volume down button; then select f11.
- or -
Turn on or restart the tablet, and then quickly hold down the Windows button; then select f11.
2. Select Troubleshoot from the boot options menu.
3. Select Recovery Manager, and then follow the on-screen instructions.
Using HP Recovery media to recover
You can use HP Recovery media to recover the original system. This method can be used if your system does
not have an HP Recovery partition or if the hard drive is not working properly.
Restore and recovery 93
1. If possible, back up all personal les.
2. Insert the HP Recovery media, and then restart the computer.
NOTE: If the computer does not automatically restart in HP Recovery Manager, change the computer
boot order. See Changing the computer boot order on page 94.
3. Follow the on-screen instructions.
Changing the computer boot order
If your computer does not restart in HP Recovery Manager, you can change the computer boot order, which is
the order of devices listed in BIOS where the computer looks for startup information. You can change the
selection to an optical drive or a USB ash drive.
To change the boot order:
IMPORTANT: For a tablet with a detachable keyboard, connect the keyboard to the keyboard dock before
beginning these steps.
1. Insert the HP Recovery media.
2. Access the system Startup menu.
For computers or tablets with keyboards attached:
▲Turn on or restart the computer or tablet, quickly press esc, and then press f9 for boot options.
For tablets without keyboards:
▲Turn on or restart the tablet, and then quickly hold down the volume up button; then select f9.
- or -
Turn on or restart the tablet, and then quickly hold down the volume down button; then select f9.
- or -
Turn on or restart the tablet, and then quickly hold down the Windows button; then select f9.
3. Select the optical drive or USB ash drive from which you want to boot.
4. Follow the on-screen instructions.
94 Chapter 9 Backup and recovery
Removing the HP Recovery partition (select products only)
HP Recovery Manager software allows you to remove the HP Recovery partition to free up hard drive space.
IMPORTANT: After you remove the HP Recovery partition, you will not be able to perform System Recovery
or create HP recovery media from the HP Recovery partition. So before you remove the Recovery partition,
create HP Recovery media; see Creating HP Recovery media (select products only) on page 90.
NOTE: The Remove Recovery Partition option is only available on products that support this function.
Follow these steps to remove the HP Recovery partition:
1. Type recovery in the taskbar search box, and then select HP Recovery Manager.
2. Select Remove Recovery Partition, and then follow the on-screen instructions.
Restore and recovery 95
10 Specications
Computer specications
Metric U.S.
Dimensions
Length 280.0 mm 11.02 in
Width 416.8 mm 16.41 in
Height (front to rear) 25.8 mm 1.02 in
Weight (1 DIMM, WLAN, webcam, no ngerprint reader, no WWAN)
M.2 SSD, no optical drive 2.60 kg 5.73 lbs
M.2 SSD, optical drive 2.71 kg 5.97 lbs
Hard dive, no optical drive 2.68 kg 5.90 lbs
Hard drive, optical drive 2.79 kg 6.15 lbs
Input power
Operating voltage 19.0 V dc @ 4.74 A – 90 W or 18.5 V dc @ 3.5 A - 65 W
Operating current 4.74 A or 3.5 A
Temperature
Operating (not writing to optical disc) 0°C to 35°C 32°F to 95°F
Operating (writing to optical disc) 5°C to 35°C 41°F to 95°F
Nonoperating -20°C to 60°C -4°F to 140°F
Relative humidity
Operating 10% to 90%
Nonoperating 5% to 95%
Maximum altitude (unpressurized)
Operating (14.7 to 10.1 psia) -15 m to 3,048 m 50 ft to 10,000 ft
Nonoperating (14.7 to 4.4 psia) -15 m to 12,192 m -50 ft to 40,000 ft
Shock
Operating 125 g, 2 ms, half-sine
Nonoperating 200 g, 2 ms, half-sine
Random vibration
Operating 0.75 g zero-to-peak, 10 Hz to 500 Hz, 0.25 oct/min sweep rate
96 Chapter 10 Specications
Metric U.S.
Nonoperating 1.50 g zero-to-peak, 10 Hz to 500 Hz, 0.5 oct/min sweep rate
NOTE: Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within this range
of temperatures.
43.9-cm (17.3-in) display specications
Metric U.S.
Active diagonal size 43.9-cm 17.3-in
Resolution 1600x900 (HD+) or 1920x1080 (FHD)
Surface treatment Anti-glare
Aspect ratio 16:9
Brightness 220 nits (HD+) or 300 nits (FHD)
Viewing angle SVA (HD+) or UWVA (FHD)
Backlight LED
43.9-cm (17.3-in) display specications 97
Hard drive specications
2.0-TB* 1-TB* 500-GB* 500-GB* hybrid
Dimensions
Height 9.5 mm 9.5 mm 7.0 mm 7.0 mm
Width 70 mm 70 mm 70 mm 70 mm
Weight 118 g 115 g 101 g or 95 g 95 g
Interface type SATA SATA SATA SATA
Transfer rate 100 MB/sec 100 MB/sec 100 MB/sec 100 MB/sec
Security ATA security ATA security ATA security ATA security
Seek times (typical read, including setting)
Single track 2.2 ms 1.4 ms 3 ms 2 ms
Average 13 ms 10 ms 13 ms 12 ms
Maximum 25 ms 12 ms 24 ms 22 ms
Logical blocks 3,877,842,922 1,938,921,461 1,048,576,000 976,773,168
Disc rotational speed 5400 rpm 5400 rpm 7200 rpm or 5400
rpm
5400 rpm
Operating temperature 0°C to 60°C (32°F to 140°F)
*1 GB = 1 billion bytes when referring to hard drive storage capacity. Actual accessible capacity is less. Actual drive specications may
dier slightly.
NOTE: Certain restrictions and exclusions apply. Contact technical support for details.
98 Chapter 10 Specications
Solid-state drive specications
128-GB* 256-GB*
Height 1.35 mm 1.35 mm
Weight < 10 g < 10 g
Form factor M.2 2280-D2-B-M M.2 2280-D2-B-M
Transfer rate up to 540 MB/sec up to 540 MB/sec
Interface type SATA-3 SATA-3
Ready time, maximum (to not busy) 1.0 ms < 1.0 ms
Access times, logical 0.1 ms 0.1 ms
Total logical sectors 234,441,648 468,883,296
Operating temperature 0°C to 70°C (32°F to 158°F)
*1 GB = 1 billion bytes when referring to hard drive storage capacity. Actual accessible capacity is less. Actual drive specications may
dier slightly.
NOTE: Certain restrictions and exclusions apply. Contact technical support for details.
Solid-state drive specications 99
DVD±RW SuperMulti DL Drive specications
Item Value
Applicable disc Read:
CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CD-ROM, CD-
ROM XA, MIXED MODE CD, CD-I, CD-I Bridge (Photo-
CD, Video CD), Multisession CD (Photo-CD, CD-
EXTRA, Portfolio, CD-R, CD-RW), CD-R, CD-RW,
DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18), DVD-
R, DVD-RW, DVD+R, DVD+RW, DVD-RAM
Write:
CD-R and CD-RW
DVD+R, DVD+RW, DVD-R, DVD-RW,
DVD-RAM
Center hole diameter 1.5 cm (0.59 in)
Disc diameter
Standard disc 12 cm (4.72 in)
Mini disc 8 cm (3.15 in)
Disc thickness 1.2 mm (0.047 in)
Track pitch 0.74 µm
Access time CD DVD
Random < 175 ms < 230 ms
Full stroke < 285 ms < 335 ms
Audio output level Line-out, 0.7 Vrms
Cache buer 2 MB
Data transfer rate
24X CD-ROM 3,600 KB/sec
8X DVD-ROM 10,800 KB/sec
24X CD-R 3,600 KB/sec
16X CD-RW 2,400 KB/sec
8X DVD+R 10,800 KB/sec
4X DVD+RW 5,400 KB/sec
8X DVD-R 10,800 KB/sec
4X DVD-RW 5,400 KB/sec
2.4X DVD+R(9) 2,700 KB/sec
5X DVD-RAM 6,750 KB/sec
Transfer mode Multiword DMA Mode
Startup time < 15 seconds
Stop time < 6 seconds
100 Chapter 10 Specications
Blu-ray ROM DVD±RW SuperMulti DL Drive
Applicable disc Read: Write:
CD-DA, CD+(E)G, CD-MIDI, CDTEXT, CD-
ROM, CD-ROM XA, MIXED MODE CD, CD-I,
CD-I Bridge (Photo-CD, Video CD),
Multisession CD (Photo-CD, CD-EXTRA,
Portfolio, CD-R, CD-RW), CD-R, CD-RW,
DVDROM (DVD-5, DVD-9, DVD-10,
DVD-18), DVD-R, DVD-RW, DVD+R, DVD
+RW, DVD-RAM, HD-ROM (Single Layer),
HD-ROM (Dual Layer), HD DVD-R, HD DVD-
R for Dual Layer, HD DVD-RW
CD-R and CD-RW DVD+R, DVD+R(9), DVD
+RW, DVD-R, DVD-R(9),DVD-RW, DVD-RAM
Access time CD DVD HD
Random 170 ms 170 ms 230 ms
Cache buer 8 MB
Data transfer rate
24X CD-ROM 3,600 KB/sec
8X DVD 10,800 KB/sec
24X CD-R 3,600 KB/sec
16X CD-RW 2,400 KB/sec
8X DVD+R 10,800 KB/sec
4X DVD+RW 5,400 KB/sec
8X DVD-R 10,800 KB/sec
4X DVD-RW 5,400 KB/sec
2.4X DVD+R(9) 2,700 KB/sec
5X DVD-RAM 6,750 KB/sec
1X BD-ROM 4,500 KB/sec
1X BD-R read 4,500 KB/sec
1X BD-RE read 4,500 KB/sec
Transfer mode Multiword DMA Mode
Blu-ray ROM DVD±RW SuperMulti DL Drive 101
DVD-ROM drive
Item Value
Applicable disc DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18, CD-ROM (Mode 1 and 2), CD Digital Audio,
CD-XA ready (Mode 2, Form 1 and Form 2), CD-I (Mode 2, Form 1 and Form 2), CD-R, CD-
RW, Photo CD (single and multisession), CD-Bridge
Center hole diameter 1.5 cm (0.59 in)
Disc diameter
Standard disc 12 cm (4.72 in)
Mini disc 8 cm (3.15 in)
Disc thickness 1.2 mm (0.047 in)
Track pitch 0.74 μm
Access time CD DVD
Random < 100 ms < 125 ms
Full Stroke < 175 ms < 225 ms
Audio output level Line-out, 0.7 Vrms
Cache buer 512 KB
Data transfer rate
CD-R (24X) 3600 KB/s (150 KB/s at 1X CD rate)
CD-RW (10X) 1500 KB/s (150 KB/s at 1X CD rate)
CD-ROM (24X) 3,600 KB/sec
DVD (8X) 3600 KB/s (150 KB/s at 1X CD rate)
Multiword DMA mode 2 16.6 MB/s
Startup time < 10 seconds
Stop time < 3 seconds
102 Chapter 10 Specications
11 Statement of memory volatility
The purpose of this chapter is to provide general information regarding nonvolatile memory in HP Business
PCs. This chapter also provides general instructions for restoring nonvolatile memory that can contain
personal data after the system has been powered o and the hard drive has been removed.
HP Business PC products that use Intel®-based or AMD®-based system boards contain volatile DDR memory.
The amount of nonvolatile memory present in the system depends upon the system conguration. Intel-
based and AMD-based system boards contain nonvolatile memory subcomponents as originally shipped from
HP, assuming that no subsequent modications have been made to the system and assuming that no
applications, features, or functionality have been added to or installed on the system.
Following system shutdown and removal of all power sources from an HP Business PC system, personal data
can remain on volatile system memory (DIMMs) for a nite period of time and will also remain in nonvolatile
memory. Use the steps below to remove personal data from the PC, including the nonvolatile memory found
in Intel-based and AMD-based system boards.
NOTE: If your tablet has a keyboard base, connect to the keyboard base before beginning steps in this
chapter.
Current BIOS steps
1. Follow steps (a) through (l) below to restore the nonvolatile memory that can contain personal data.
Restoring or reprogramming nonvolatile memory that does not store personal data is neither necessary
nor recommended.
a. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
IMPORTANT: If the Main menu displays Restore Defaults instead of Apply Factory Defaults and
Exit, go to Legacy BIOS Steps on page 104.
NOTE: If the system has a BIOS administrator password, enter the password at the prompt.
b. Select Main, select Apply Factory Defaults and Exit, and then select Yes to load defaults.
The computer will reboot.
c. During the reboot, press esc while the “Press the ESC key for Startup Menu” message is displayed
at the bottom of the screen.
NOTE: If the system has a BIOS administrator password, enter the password at the prompt.
d. Select the Security menu, select Restore Security Settings to Factory Defaults, and then select
Yes to restore security level defaults.
The computer will reboot.
e. During the reboot, press esc while the “Press the ESC key for Startup Menu” message is displayed
at the bottom of the screen.
NOTE: If the system has a BIOS administrator password, enter the password at the prompt.
f. If an asset or ownership tag is set, select the Security menu and scroll down to the Utilities menu.
Select System IDs, and then select Asset Tracking Number. Clear the tag, and then make the
selection to return to the prior menu.
103
g. If a DriveLock password is set, select the Security menu, and scroll down to Hard Drive Utilities
under the Utilities menu. Select Hard Drive Utilities, select DriveLock, then uncheck the checkbox
for DriveLock password on restart. Select OK to proceed.
h. Select the Main menu, and then select Reset BIOS Security to factory default. Click Yes at the
warning message.
The computer will reboot.
i. During the reboot, press esc while the “Press the ESC key for Startup Menu” message is displayed
at the bottom of the screen.
NOTE: If the system has a BIOS administrator password, enter the password at the prompt.
j. Select the Main menu, select Apply Factory Defaults and Exit, select Yes to save changes and exit,
and then select Shutdown.
k. Reboot the system. If the system has a Trusted Platform Module (TPM) and/or ngerprint reader,
one or two prompts will appear—one to clear the TPM and the other to Reset Fingerprint Sensor;
press or tap F1 to accept or F2 to reject.
l. Remove all power and system batteries for at least 24 hours.
2. Complete one of the following:
●Remove and retain the storage drive.
– or –
●Clear the drive contents by using a third party utility designed to erase data from an SSD.
– or –
●Clear the contents of the drive by using the following BIOS Setup Secure Erase command option
steps:
IMPORTANT: If you clear data using Secure Erase, it cannot be recovered.
a. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
b. Select the Security menu and scroll down to the Utilities menu.
c. Select Hard Drive Tools.
d. Under Utilities, select Secure Erase, select the hard drive storing the data you want to clear, and
then follow the on-screen instructions to continue.
Legacy BIOS Steps
Use the steps for older versions of BIOS.
NOTE: If you already completed the steps in Current BIOS steps on page 103, skip this section.
1. Follow steps (a) through (i) below to restore the nonvolatile memory that can contain personal data.
Restoring or reprogramming nonvolatile memory that does not store personal data is neither necessary
nor recommended.
NOTE: If you have not already done so, access the BIOS menu.
●Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
104 Chapter 11 Statement of memory volatility
NOTE: If the system has a BIOS administrator password, enter the password at the prompt.
a. Select Main, select Restore Defaults, and then select Yes to load defaults.
b. Select the Security menu, select Restore Security Level Defaults, and then select Yes to restore
security level defaults.
c. If an asset or ownership tag is set, select the Security menu and scroll down to the Utilities menu.
Select System IDs, and then select Asset Tracking Number. Clear the tag, and then make the
selection to return to the prior menu.
d. If a DriveLock password is set, select the Security menu, and scroll down to Hard Drive Tools
under the Utilities menu. Select Hard Drive Tools, select DriveLock, then uncheck the checkbox
for DriveLock password on restart. Select OK to proceed.
e. If an Automatic DriveLock password is set, select the Security menu, scroll down to Hard Drive
Tools under the Utilities menu. Select Hard Drive Tools, scroll down to Automatic DriveLock, then
select the desired hard drive and disable protection. At the automatic drive lock warning screen,
select Yes to continue. Repeat this procedure if more than one hard drive has an Automatic
DriveLock password.
f. Select the Main menu, and then select Reset BIOS Security to factory default. Click Yes at the
warning message.
g. Select the Main menu, select Save Changes and Exit, select Yes to save changes and exit, and then
select Shutdown.
h. Reboot the system. If the system has a Trusted Platform Module (TPM) and/or ngerprint reader,
one or two prompts will appear—one to clear the TPM and the other to Reset Fingerprint Sensor;
press or tap F1 to accept or F2 to reject.
i. Remove all power and system batteries for at least 24 hours.
2. Complete one of the following:
●Remove and retain the storage drive.
– or –
●Clear the drive contents by using a third party utility designed to erase data from an SSD.
– or –
●Clear the contents of the drive by using the following BIOS Setup Secure Erase command option
steps:
IMPORTANT: If you clear data using Secure Erase, it cannot be recovered.
a. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
b. Select the Security menu and scroll down to the Utilities menu.
c. Select Hard Drive Tools.
d. Under Utilities, select Secure Erase, select the hard drive storing the data you want to clear, and
then follow the on-screen instructions to continue.
– or –
●Clear the contents of the drive by using the following Disk Sanitizer command steps:
IMPORTANT: If you clear data using Disk Sanitizer, it cannot be recovered.
105
NOTE: The amount of time it takes for Disk Sanitizer to run can take several hours. Plug the computer
into an AC outlet before starting.
a. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
b. Select the Security menu and scroll down to the Utilities menu.
c. Select Hard Drive Tools.
d. Under Utilities, select Disk Sanitizer, select the hard drive storing the data you want to clear, and
then follow the on-screen instructions to continue.
Nonvolatile memory usage
Nonvolatile
Memory Type Amount (Size)
Does this
memory
store
customer
data?
Does this
memory
retain data
when power
is removed?
What is the
purpose of this
memory?
How is data input into this
memory?
How is this memory
write-protected?
HP Sure Start ash
(select models
only)
2 MBytes No Yes Provides
protected
backup of
critical System
BIOS code, EC
rmware, and
critical PC
conguration
data for select
platforms that
support HP
Sure Start.
For more
information,
see Using HP
Sure Start
(select models
only)
on page 109.
Data cannot be written to this
device via the host processor.
The content is managed
solely by the HP Sure Start
Embedded Controller.
This memory is protected
by the HP Sure Start
Embedded Controller.
Real Time Clock
(RTC) battery
backed-up CMOS
conguration
memory
256 Bytes No Yes Stores system
date and time
and noncritical
data.
RTC battery backed-up CMOS
is programmed using the
Computer Setup (BIOS), or
changing the Microsoft
Windows date & time.
This memory is not write-
protected.
Controller (NIC)
EEPROM
64 KBytes (not
customer
accessible)
No Yes Stores NIC
conguration
and NIC
rmware.
NIC EEPROM is programmed
using a utility from the NIC
vendor that can be run from
DOS.
A utility is required to
write data to this memory
and is available from the
NIC vendor. Writing data
to this ROM in an
inappropriate manner will
render the NIC non-
functional.
DIMM Serial
Presence Detect
(SPD)
conguration data
256 Bytes per
memory
module, 128
Bytes
programmable
No Yes Stores memory
module
information.
DIMM SPD is programmed by
the memory vendor.
Data cannot be written to
this memory when the
module is installed in a
PC. The specic write-
protection method varies
by memory vendor.
106 Chapter 11 Statement of memory volatility
Nonvolatile
Memory Type Amount (Size)
Does this
memory
store
customer
data?
Does this
memory
retain data
when power
is removed?
What is the
purpose of this
memory?
How is data input into this
memory?
How is this memory
write-protected?
(not customer
accessible)
System BIOS 4 MBytes to 5
MBytes
Yes Yes Stores system
BIOS code and
PC
conguration
data.
System BIOS code is
programmed at the factory.
Code is updated when the
system BIOS is updated.
Conguration data and
settings are input using the
Computer Setup (BIOS) or a
custom utility.
NOTE: Writing data to
this ROM in an
inappropriate manner can
render the PC non-
functional.
A utility is required for
writing data to this
memory and is available
on the HP website; go to
http://www.hp.com/
support. Select Find your
product, and then follow
the on-screen
instructions.
Intel Management
Engine Firmware
(present in only
specic ZBook and
EliteBook models.
For more
information, go to
http://www.hp.com/
support. Select
Find your
product, and then
follow the on-
screen
instructions.)
1.5 MBytes or 5
MBytes
Yes Yes Stores
Management
Engine Code,
Settings,
Provisioning
Data and iAMT
third-party data
store.
Management Engine Code is
programmed at the factory.
Code is updated via Intel
secure rmware update
utility. Unique Provisioning
Data can be entered at the
factory or by an
administrator using the
Management Engine (MEBx)
setup utility. The third party
data store contents can be
populated by a remote
management console or local
applications that have been
registered by an
administrator to have access
to the space.
The Intel chipset is
congured to enforce
hardware protection to
block all direct read/write
access to this area. An
Intel utility is required for
updating the rmware.
Only rmware updates
digitally signed by Intel
can be applied using this
utility.
Bluetooth ash 2 Mbit No Yes Stores
Bluetooth
conguration
and rmware.
Bluetooth ash is
programmed at the factory.
Tools for writing data to this
memory are not publicly
available but can be obtained
from the silicon vendor.
A utility is required for
writing data to this
memory and is made
available through newer
versions of the driver
whenever the ash
requires an upgrade.
802.11 WLAN
EEPROM
4 Kbit to 8 Kbit No Yes Stores
conguration
and calibration
data.
802.11 WLAN EEPROM is
programmed at the factory.
Tools for writing data to this
memory are not made public.
A utility is required for
writing data to this
memory and is typically
not made available to the
public unless a rmware
upgrade is necessary to
address a unique issue.
Web camera 64 Kbit No Yes Stores webcam
conguration
and rmware.
Webcam memory is
programmed using a utility
from the device
manufacturer that can be run
from Windows.
A utility is required for
writing data to this
memory and is typically
not made available to the
public unless a rmware
Nonvolatile memory usage 107
Nonvolatile
Memory Type Amount (Size)
Does this
memory
store
customer
data?
Does this
memory
retain data
when power
is removed?
What is the
purpose of this
memory?
How is data input into this
memory?
How is this memory
write-protected?
upgrade is necessary to
address a unique issue.
Fingerprint reader 512 KByte ash Yes Yes Stores
ngerprint
templates.
Fingerprint reader memory is
programmed by user
enrollment in HP
ProtectTools Security
Manager.
Only a digitally signed
application can make the
call to write to the ash.
Questions and answers
1. How can the BIOS settings be restored (returned to factory settings)?
IMPORTANT: Restore defaults does not securely erase any data on your hard drive. See question and
answer 6 for steps to securely erase data.
Restore defaults does not reset the Custom Secure Boot keys. See question and answer 7 for
information about resetting the keys.
a. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
b. Select Main, and then select Restore defaults.
c. Follow the on-screen instructions.
d. Select Main, select Save Changes and Exit, and then follow the on-screen instructions.
2. What is a UEFI BIOS, and how is it dierent from a legacy BIOS?
The Unied Extensible Firmware Interface (UEFI) BIOS is an industry-standard software interface
between the platform rmware and an operating system (OS). It is a replacement for the older BIOS
architecture, but supports much of the legacy BIOS functionality.
Like the legacy BIOS, the UEFI BIOS provides an interface to display the system information and
conguration settings and to change the conguration of your computer before an OS is loaded. BIOS
provides a secure run-time environment that supports a Graphic User Interface (GUI). In this
environment, you can use either a pointing device (Touchscreen, TouchPad, pointing stick, or USB
mouse) or the keyboard to navigate and make menu and conguration selections. The UEFI BIOS also
contains basic system diagnostics.
The UEFI BIOS provides functionality beyond that of the legacy BIOS. In addition, the UEFI BIOS works to
initialize the computer’s hardware before loading and executing the OS; the run-time environment
allows the loading and execution of software programs from storage devices to provide more
functionality, such as advanced hardware diagnostics (with the ability to display more detailed system
information) and advanced rmware management and recovery software.
HP has provided options in Computer Setup (BIOS) to allow you to run in legacy BIOS, if required by the
operating system. Examples of this requirement would be if you upgrade or downgrade the OS.
3. Where does the UEFI BIOS reside?
The UEFI BIOS resides on a ash memory chip. A utility is required to write to the chip.
108 Chapter 11 Statement of memory volatility
4. What kind of conguration data is stored on the DIMM Serial Presence Detect (SPD) memory
module? How would this data be written?
The DIMM SPD memory contains information about the memory module, such as size, serial number,
data width, speed/timing, voltage, and thermal information. This information is written by the module
manufacturer and stored on an EEPROM. This EEPROM cannot be written to when the memory module is
installed in a PC. Third-party tools do exist that can write to the EEPROM when the memory module is
not installed in a PC. Various third-party tools are available to read SPD memory.
5. What is meant by “Restore the nonvolatile memory found in Intel-based system boards”?
This message relates to clearing the Real Time Clock (RTC) CMOS memory that contains PC conguration
data.
6. How can the BIOS security be reset to factory defaults and data erased?
IMPORTANT: Resetting will result in the loss of information.
These steps will not reset Custom Secure Boot Keys. See question and answer 7 for information about
resetting the keys.
a. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
b. Select Main, and then select Reset BIOS Security to Factory Default.
c. Follow the on-screen instructions.
d. Select Main, select Save Changes and Exit, and then follow the on-screen instructions.
7. How can the Custom Secure Boot Keys be reset?
Secure Boot is a feature to ensure that only authenticated code can start on a platform. If you enabled
Secure Boot and created Custom Secure Boot Keys, simply disabling Secure Boot will not clear the keys.
You must also select to clear the Custom Secure Boot Keys. Use the same Secure Boot access procedure
you used to create the Custom Secure Boot Keys, but make the selection to clear or delete all Secure
Boot Keys.
a. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
b. Select the Security menu, select Secure Boot Conguration, and then follow the on-screen
instructions.
c. At the Secure Boot Conguration window, select Secure Boot, select Clear Secure Boot Keys, and
then follow the on-screen instructions to continue.
Using HP Sure Start (select models only)
Select computer models are congured with HP Sure Start, a technology that continuously monitors your
computer's BIOS for attacks or corruption. If the BIOS becomes corrupted or is attacked, HP Sure Start
restores the BIOS to its previously safe state, without user intervention. Those select computer models ship
with HP Sure Start congured and enabled. HP Sure Start is congured and already enabled so that most
users can use the HP Sure Start default conguration. The default conguration can be customized by
advanced users.
To access the latest documentation on HP Sure Start, go to http://www.hp.com/support. Select Find your
product, and then follow the on-screen instructions.
Using HP Sure Start (select models only) 109
12 Power cord set requirements
The wide-range input feature of the computer permits it to operate from any line voltage from 100 to 120
volts ac, or from 220 to 240 volts ac.
The 3-conductor power cord set included with the computer meets the requirements for use in the country or
region where the equipment is purchased.
Power cord sets for use in other countries and regions must meet the requirements of the country or region
where the computer is used.
Requirements for all countries and regions
The following requirements are applicable to all countries and regions:
●The length of the power cord set must be at least 1.5 m (5.0 ft) and no more than 2.0 m (6.5 ft).
●All power cord sets must be approved by an acceptable accredited agency responsible for evaluation in
the country or region where the power cord set will be used.
●The power cord sets must have a minimum current capacity of 10 A and a nominal voltage rating of 125
or 250 V ac, as required by the power system of each country or region.
●The appliance coupler must meet the mechanical conguration of an EN 60 320/IEC 320 Standard Sheet
C13 connector for mating with the appliance inlet on the back of the computer.
Requirements for specic countries and regions
Country/region Accredited agency Applicable note number
Argentina IRAM 1
Australia SAA 1
Austria OVE 1
Belgium CEBEC 1
Brazil ABNT 1
Canada CSA 2
Chile IMQ 1
Denmark DEMKO 1
Finland FIMKO 1
France UTE 1
Germany VDE 1
India ISI 1
Israel SII 1
Italy IMQ 1
110 Chapter 12 Power cord set requirements
Country/region Accredited agency Applicable note number
Japan JIS 3
The Netherlands KEMA 1
New Zealand SANZ 1
Norway NEMKO 1
The People's Republic of China CCC 4
Saudi Arabia SASO 7
Singapore PSB 1
South Africa SABS 1
South Korea KTL 5
Sweden SEMKO 1
Switzerland SEV 1
Taiwan BSMI 6
Thailand TISI 1
The United Kingdom ASTA 1
The United States UL 2
1. The exible cord must be Type HO5VV-F, 3-conductor, 0.75mm2 conductor size. Power cord set ttings (appliance coupler and
wall plug) must bear the certication mark of the agency responsible for evaluation in the country or region where it will be used.
2. The exible cord must be Type SVT/SJT or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole grounding type
with a NEMA 5-15P (15 A, 125 V ac) or NEMA 6-15P (15 A, 250 V ac) conguration. CSA or C-UL mark. UL le number must be on
each element.
3. The appliance coupler, exible cord, and wall plug must bear a “T” mark and registration number in accordance with the Japanese
Dentori Law. The exible cord must be Type VCTF, 3-conductor, 0.75mm2 or 1.25mm2 conductor size. The wall plug must be a
two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V ac) conguration.
4. The exible cord must be Type RVV, 3-conductor, 0.75mm2 conductor size. Power cord set ttings (appliance coupler and wall
plug) must bear the CCC certication mark.
5. The exible cord must be Type H05VV-F 3X0.75mm2 conductor size. KTL logo and individual approval number must be on each
element. Corset approval number and logo must be printed on a ag label.
6. The exible cord must be Type HVCTF 3X1.25mm2 conductor size. Power cord set ttings (appliance coupler, cable, and wall
plug) must bear the BSMI certication mark.
7. For 127 V ac, the exible cord must be Type SVT or SJT 3 x 18 AWG, with plug NEMA 5-15P (15 A, 125 V ac), with UL and CSA or C-
UL marks. For 240 V ac, the exible cord must be Type H05VV-F 3X0.75/1.00mm2 conductor size, with plug BS 1363/A with BSI
or ASTA marks.
Requirements for specic countries and regions 111
13 Recycling
When a non-rechargeable or rechargeable battery has reached the end of its useful life, do not dispose of the
battery in general household waste. Follow the local laws and regulations in your area for battery disposal.
HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable
batteries. For more information about recycling programs, see the HP Web site at http://www.hp.com/recycle.
112 Chapter 13 Recycling
Index
A
AC adapter, spare part numbers 23
antennas
disconnecting 38
audio, product description 2
audio-out (headphone)/audio-in
(microphone) combo jack,
identifying 5
B
backups 90
base enclosure, spare part number
16
battery
removing 62
spare part number 16, 62
battery light 6
BIOS
determining version 85
downloading an update 86
updating 85
Blu-ray ROM DVD±RW SuperMulti
specications 101
Bluetooth card
spare part number 38
Bluetooth label 14
boot order
changing 94
bottom 14
buttons
left TouchPad 8
optical drive eject 5
power 10
right TouchPad 8
C
Cable Kit
contents 18
spare part number 18
cables, service considerations 26
caps lock light, identifying 9
components
bottom 13
display 7
left side 6
right side 5
top 8
Computer Setup
navigating and selecting 84
restoring factory settings 84
computer specications 96
connector, power 6
connectors, service considerations
26
D
diskette drive
precautions 26
display assembly
removal 76
removing 44
spare part numbers 76
display assembly subcomponents
removing 44
display bezel
removal 77
removing 45
spare part numbers 19
display components, spare part
numbers 19
Display Hinge Kit
spare part numbers 20
display panel
product description 1
removing 46
display rear cover
spare part number 20
display specications 97
drive light, identifying 6
drives
preventing damage 26
DVD-ROM drive, specications 102
DVD±RW SuperMulti DL Drive
specications 100
E
electrostatic discharge 27
esc key, identifying 11
Ethernet, product description 2
external media cards, product
description 2
external monitor port 6
F
fan
removing 66
spare part number 16
ngerprint reader assembly
removal 52
spare part number 16, 52
ngerprint reader, identifying 10
fn key, identifying 11
function board
removal 56
spare part number 16, 56
G
graphics, product description 1
grounding equipment and methods
29
H
hard drive
precautions 26
product description 1
removing 34
spare part numbers 17, 22, 34
specications 98
hard drive hardware kit
spare part number 17
Hard Drive Hardware Kit, spare part
number 22
hard drive, identifying 13
HDMI port, identifying 6
heat sink
removal 74
spare part number 16, 74
hinge cover
spare part number 20
hinges
removing 46
hot keys
microphone mute 12
using 12
Index 113
HP PC Hardware Diagnostics (UEFI)
using 88
HP Recovery Manager
correcting boot problems 94
starting 93
HP Recovery media
creating 90
recovery 93
HP Recovery partition
recovery 93
removing 95
HP Sure Start 109
I
integrated numeric keypad,
identifying 11
integrated webcam light,
identifying 7
internal microphones, identifying 7
J
jacks
audio-out (headphone)/audio-in
(microphone) combo 5
network 5
RJ-45 (network) 5
K
keyboard
product description 3
removal 41
spare part numbers 16, 41
keypad
integrated numeric 11
keys
esc 11
fn 11
Windows key 11
L
labels
Bluetooth 14
regulatory 14
serial number 14
service 14
wireless certication 14
WLAN 14
legacy support, USB 84
lights
battery 6
caps lock 9
hard drive 6
microphone mute 9
num lock 9
power 9
RJ-45 (network) 5
webcam 7
wireless 9
M
M.2 solid-state drive
removal 40
spare part number 40
mass storage devices, spare part
numbers 22
memory
nonvolatile 103
volatile 103
memory card reader, identifying 6
memory module
identifying 13
product description 1
removal 36
spare part numbers 16, 36
microphone (audio-in) jack
product description 2
microphone module
spare part number 19
microphone mute key, identifying
12
microphone mute light, identifying
9
mini card
product description 2
minimized image recovery 93
minimized image, creating 92
model name 1
N
network jack, identifying 5
nonvolatile memory 103
num lock light 9
O
operating system, product
description 3
optical drive
precautions 26
product description 2
removing 32
spare part numbers 17, 22, 32
specications 100, 101, 102
optical drive cable and connector
spare part number 16
optical drive connector cable
removal 68
spare part number 68
optical drive eject button,
identifying 5
optical drive, identifying 5
original system recovery 92
P
packing guidelines 28
plastic parts 25
Plastics Kit
contents 21
spare part number 21
pointing device, product
description 3
ports
external monitor 6
HDMI 6
product description 2
USB 5
USB Type-C charging 6
power button board
spare part number 16
power button board assembly
removal 54
spare part number 54
power button, identifying 10
power cable
removal 83
spare part number 16, 83
power connector, identifying 6
power cord
set requirements 110
spare part numbers 23
power lights 9
power requirements, product
description 3
processor
product description 1
product description
audio 2
display panel 1
Ethernet 2
external media cards 2
graphics 1
hard drives 1
keyboard 3
114 Index
memory module 1
microphone 2
mini card 2
operating system 3
optical drives 2
pointing devices 3
ports 2
power requirements 3
processors 1
product name 1
security 3
serviceability 4
webcam 2
wireless 2
product name 1
product name and number,
computer 14
R
recover
options 92
recovery
discs 91, 93
HP Recovery Manager 92
media 93
starting 93
supported discs 91
system 92
USB ash drive 93
using HP Recovery media 91
recovery media
creating 90
creating using HP Recovery
Manager 91
recovery partition
removing 95
regulatory information
regulatory label 14
wireless certication labels 14
removal/replacement
preliminaries 25
procedures, Authorized Service
Provider 44
procedures, Customer Self-
Repair 30
removing personal data from volatile
system memory 103
RJ-45 (network) jack, identifying 5
RJ-45 (network) lights, identifying
5
RTC battery
removal 73
spare part number 16, 73
S
Screw Kit, spare part number 24
security cable slot, identifying 5
security, product description 3
serial number 14
serial number, computer 14
service considerations 25
service door
removing 31
spare part number 31
service labels, locating 14
serviceability, product description 4
setup utility
navigating and selecting 84
restoring factory settings 84
SIM card slot, identifying 13
SIM hinged connector, identifying
13
slots
security cable 5
SIM card 13
solid-state drive
removal 40
spare part number 40
spare part numbers 16, 22
specications 99
speaker assembly
removal 58
spare part number 16, 58
speakers, identifying 10
specications
Blu-ray ROM DVD±RW
SuperMulti 101
computer 96
display 97
DVD-ROM drive 102
DVD±RW SuperMulti DL Drive
100
hard drive 98
optical drive 100, 101, 102
solid-state drive 99
static-shielding materials 29
supported discs, recovery 91
Sure Start
using 87
system board
removal 70
spare part numbers 16, 70
system memory, removing personal
data from volatile 103
system recovery 92
system restore point
creating 91
system restore point, creating 90
T
thermal material, replacement 75
tools required 25
top cover
removal 48
spare part number 16, 48
TouchPad
buttons 8
TouchPad assembly
removal 60
spare part number 60
TouchPad zone
identifying 8
TPM settings 87
transporting guidelines 28
traveling with the computer 14
U
USB 3.0 port 6
USB legacy support 84
USB ports, identifying 5, 6
USB Type-C charging port,
identifying 6
USB/audio board
removal 64
spare part number 16, 64
V
vents, identifying 6, 13
W
webcam 7
product description 2
webcam light, identifying 7
webcam module
removal 79
spare part number 19
webcam, identifying 7
webcam/microphone cable
removing 46
Index 115
webcam/microphone module
removing 45
Windows
system restore point 90, 91
Windows key, identifying 11
Windows tools
using 91
wireless antennas
disconnecting 38
wireless antennas, identifying 7
wireless certication label 14
wireless light 9
wireless, product description 2
WLAN antennas, identifying 7
WLAN device 14
WLAN label 14
WLAN/Bluetooth combo card
removal 38
spare part number 16, 38
workstation guidelines 28
WWAN antennas, identifying 7
116 Index