Table of Contents
- Product description
- External component identification
- Illustrated parts catalog
- Removal and replacement preliminary requirements
- Removal and replacement procedures – slate
- Unlocking the device and disabling Always On Remote Management (select HP devices only)
- Display panel assembly
- Battery
- WLAN module
- WWAN module
- Speakers
- Vibrator module
- Fan
- Volume button board
- Docking connector board
- Audio jack board
- System board
- Volume button board cable
- RTC battery
- Solid-state drive
- Heat sink
- Rear-facing webcam
- Front-facing webcam
- WWAN antenna
- WLAN antenna
- WiGig antenna
- Docking connector board cable
- Removal and replacement procedures – Keyboard base
- Computer Setup (BIOS), TPM, and HP Sure Start – Windows 10
- HP PC Hardware Diagnostics (UEFI) – Windows 10
- Computer Setup (BIOS), MultiBoot, and HP PC Hardware Diagnostics (UEFI) – Windows 8
- Computer Setup (BIOS), MultiBoot, and HP PC Hardware Diagnostics (UEFI) – Windows 7
- Specifications
- Backup and recovery – Windows 10
- Backup and recovery – Windows 8
- Backup and recovery – Windows 7
- Statement of Volatility
- Backup and recovery – Windows 7
- Power cord set requirements
- Recycling
- Index
HP Elite x2 1011 G1 User Manual
Displayed below is the user manual for Elite x2 1011 G1 by HP which is a product in the Notebooks category. This manual has pages.
Related Manuals
HP Elite x2 1011 G1
Maintenance and Service Guide
IMPORTANT! This document is intended for
HP authorized service providers only.
© Copyright 2015 HP Development Company,
L.P.
Bluetooth is a trademark owned by its
proprietor and used by HP Inc. under license.
DTS, the Symbol, & DTS and the Symbol
together are registered trademarks, and DTS
Sound is a trademark of DTS, Inc. © DTS, Inc.
All Rights Reserved. Intel and Core are U.S.
registered trademarks of Intel Corporation.
Microsoft and Windows are U.S. registered
trademarks of Microsoft Corporation. SD Logo
is a trademark of its proprietor.
The information contained herein is subject to
change without notice. The only warranties for
HP products and services are set forth in
the express warranty statements
accompanying such products and services.
Nothing herein should be construed as
constituting an additional warranty. HP shall
not be liable for technical or editorial errors or
omissions contained herein.
Second Edition: August 2015
First Edition: February 2015
Document Part Number: 780896-002
Product notice
This guide describes features that are common
to most models. Some features may not be
available on your slate.
Not all features are available in all editions of
Windows 10 and Windows 8. This slate may
require upgraded and/or separately purchased
hardware, drivers, and/or software to take full
advantage of Windows 10 and Windows 8
functionality. See for
http://www.microsoft.com details.
Safety warning notice
WARNING! To reduce the possibility of heat-related injuries or of overheating the device, do not place
the device directly on your lap or obstruct the device air vents. Use the device only on a hard, flat surface. Do
not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or
rugs or clothing, to block airflow. Also, do not allow the AC adapter to contact the skin or a soft surface, such
as pillows or rugs or clothing, during operation. The device and the AC adapter comply with the user-
accessible surface temperature limits defined by the International Standard for Safety of Information
Technology Equipment (IEC 60950).
iii
iv Safety warning notice
Table of contents
1 Product description ....................................................................................................................................... 1
2 External component identification ................................................................................................................. 6
Slate edge components ......................................................................................................................................... 6
Slate display components ..................................................................................................................................... 9
Keyboard base ..................................................................................................................................................... 11
Keys ...................................................................................................................................................................... 12
Lights ................................................................................................................................................................... 13
TouchPad ............................................................................................................................................................. 14
Left side ............................................................................................................................................................... 15
Right side ............................................................................................................................................................. 16
3 Illustrated parts catalog .............................................................................................................................. 19
Locating the product name, serial number, product number, warranty information, and model name .......... 19
Slate major components ..................................................................................................................................... 20
Keyboard base ..................................................................................................................................................... 24
Miscellaneous parts ............................................................................................................................................. 26
4 Removal and replacement preliminary requirements ..................................................................................... 30
Tools required ...................................................................................................................................................... 30
Service considerations ........................................................................................................................................ 30
Plastic parts ....................................................................................................................................... 30
Cables and connectors ...................................................................................................................... 30
Grounding guidelines ........................................................................................................................................... 31
Electrostatic discharge damage ....................................................................................................... 31
Packaging and transporting guidelines ......................................................................... 32
Workstation guidelines ................................................................................ 32
5 Removal and replacement procedures – slate ................................................................................................ 34
Unlocking the device and disabling Always On Remote Management (select HP devices only) ....................... 34
Display panel assembly ....................................................................................................................................... 35
Battery ................................................................................................................................................................. 39
WLAN module ...................................................................................................................................................... 40
WWAN module ..................................................................................................................................................... 42
Speakers .............................................................................................................................................................. 44
Vibrator module ................................................................................................................................................... 45
v
Fan ....................................................................................................................................................................... 46
Volume button board .......................................................................................................................................... 47
Docking connector board .................................................................................................................................... 49
Audio jack board .................................................................................................................................................. 51
System board ....................................................................................................................................................... 52
Volume button board cable ................................................................................................................................. 58
RTC battery .......................................................................................................................................................... 59
Solid-state drive .................................................................................................................................................. 60
Heat sink .............................................................................................................................................................. 62
Rear-facing webcam ............................................................................................................................................ 64
Front-facing webcam .......................................................................................................................................... 65
WWAN antenna .................................................................................................................................................... 67
WLAN antenna ..................................................................................................................................................... 70
WiGig antenna ...................................................................................................................................................... 71
Docking connector board cable ........................................................................................................................... 72
6 Removal and replacement procedures – Keyboard base .................................................................................. 74
Bottom cover ....................................................................................................................................................... 74
Keyboard base battery ........................................................................................................................................ 75
Power connector cable ........................................................................................................................................ 76
Keyboard .............................................................................................................................................................. 77
Fingerprint reader board ..................................................................................................................................... 80
TouchPad ............................................................................................................................................................. 81
Smart card reader board ..................................................................................................................................... 82
Connector board .................................................................................................................................................. 83
Keyboard base system board .............................................................................................................................. 84
Fingerprint reader board cable ........................................................................................................................... 87
Kickstand ............................................................................................................................................................. 88
Hinge assembly ................................................................................................................................................... 89
7 Computer Setup (BIOS), TPM, and HP Sure Start – Windows 10 ........................................................................ 91
Using Computer Setup ......................................................................................................................................... 91
Starting Computer Setup .................................................................................................................. 91
Navigating and selecting in Computer Setup ................................................................................... 92
Restoring factory settings in Computer Setup ................................................................................. 92
Updating the BIOS ............................................................................................................................. 93
Determining the BIOS ..................................................................................................... 93
Downloading a BIOS update ........................................................................................... 93
Changing the boot order using the f9 prompt .................................................................................. 94
TPM BIOS settings (select products only) ........................................................................................................... 95
Using HP Sure Start (select products only) ......................................................................................................... 95
vi
8 HP PC Hardware Diagnostics (UEFI) – Windows 10 ........................................................................................... 96
Downloading HP PC Hardware Diagnostics (UEFI) to a USB device .................................................................... 97
9 Computer Setup (BIOS), MultiBoot, and HP PC Hardware Diagnostics (UEFI) – Windows 8 ................................... 98
Using Computer Setup ......................................................................................................................................... 98
Starting Computer Setup .................................................................................................................. 98
Navigating and selecting in Computer Setup ................................................................................... 98
Restoring factory settings in Computer Setup ................................................................................. 99
Updating the BIOS ........................................................................................................................... 100
Determining the BIOS version ...................................................................................... 100
Downloading a BIOS update ......................................................................................... 100
Using MultiBoot ................................................................................................................................................. 101
About the boot device order ........................................................................................................... 101
Choosing MultiBoot preferences .................................................................................................... 101
Setting a new boot order in Computer Setup .............................................................. 101
Dynamically choosing a boot device using the f9 prompt ........................................... 102
Setting a MultiBoot Express prompt ............................................................................ 102
Entering MultiBoot Express preferences ..................................................................... 103
Using HP PC Hardware Diagnostics (UEFI) ........................................................................................................ 103
Downloading HP PC Hardware Diagnostics (UEFI) to a USB device ............................................... 103
Using HP Sure Start (select models only) ......................................................................................................... 104
10 Computer Setup (BIOS), MultiBoot, and HP PC Hardware Diagnostics (UEFI) – Windows 7 ............................... 105
Using Computer Setup ....................................................................................................................................... 105
Starting Computer Setup ................................................................................................................ 105
Navigating and selecting in Computer Setup ................................................................................. 105
Restoring factory settings in Computer Setup ............................................................................... 106
Updating the BIOS ........................................................................................................................... 107
Determining the BIOS version ...................................................................................... 107
Downloading a BIOS update ......................................................................................... 107
Using MultiBoot ................................................................................................................................................. 108
About the boot device order ........................................................................................................... 108
Choosing MultiBoot preferences .................................................................................................... 108
Setting a new boot order in Computer Setup .............................................................. 108
Dynamically choosing a boot device using the f9 prompt ........................................... 109
Setting a MultiBoot Express prompt ............................................................................ 109
Entering MultiBoot Express preferences ..................................................................... 109
Using HP PC Hardware Diagnostics (UEFI) (select models only) ...................................................................... 110
Downloading HP PC Hardware Diagnostics (UEFI) to a USB device ............................................... 110
vii
11 Specifications .......................................................................................................................................... 112
12 Backup and recovery – Windows 10 ........................................................................................................... 113
Creating recovery media and backups .............................................................................................................. 113
Creating HP Recovery media (select products only) ...................................................................... 114
Using Windows Tools ........................................................................................................................................ 115
Restore and recovery ........................................................................................................................................ 115
Recovering using HP Recovery Manager ........................................................................................ 116
What you need to know before you get started .......................................................... 116
Using the HP Recovery partition (select products only) .............................................. 117
Using HP Recovery media to recover ........................................................................... 117
Changing the computer boot order .............................................................................. 118
Removing the HP Recovery partition (select products only) ....................................... 118
13 Backup and recovery – Windows 8 ............................................................................................................. 119
Backing up your information ............................................................................................................................. 119
Performing a system recovery .......................................................................................................................... 119
Using the Windows recovery tools ................................................................................................. 120
Using f11 recovery tools ................................................................................................................. 120
Using Windows operating system media (purchased separately) ................................................ 121
Using Windows Refresh or Windows Reset .................................................................................... 122
Using HP Software Setup ................................................................................................................ 122
14 Backup and recovery – Windows 7 ............................................................................................................. 123
Creating recovery media and backups .............................................................................................................. 123
Guidelines ........................................................................................................................................ 123
Creating recovery media with HP Recovery Disc Creator ............................................................... 123
Creating recovery media .............................................................................................. 124
Backing up your information .......................................................................................................... 124
Performing a system recovery .......................................................................................................................... 125
Using the Windows recovery tools ................................................................................................. 125
Using f11 recovery tools (select models only) ............................................................................... 126
Using Windows 7 operating system media .................................................................................... 126
15 Statement of Volatility ............................................................................................................................ 128
Non-volatile memory usage ............................................................................................................................. 130
Questions and answers ..................................................................................................................................... 132
16 Backup and recovery – Windows 7 ............................................................................................................. 123
Creating recovery media and backups .............................................................................................................. 134
viii
Guidelines ........................................................................................................................................ 134
Creating recovery media with HP Recovery Disc Creator ............................................................... 123
Creating recovery media .............................................................................................. 135
Backing up your information .......................................................................................................... 124
Performing a system recovery .......................................................................................................................... 136
Using the Windows recovery tools ................................................................................................. 136
Using f11 recovery tools (select models only) ............................................................................... 137
Using Windows 7 operating system media .................................................................................... 126
17 Power cord set requirements .................................................................................................................... 139
Requirements for all countries ......................................................................................................................... 139
Requirements for specific countries and regions ............................................................................................. 139
18 Recycling ................................................................................................................................................ 141
Index ........................................................................................................................................................... 142
ix
x
1 Product description
Category Description
Product Name HP Elite x2 1011 G1
Processor ●Intel® Core™ i7 M-5Y71 processor
●Intel Core i5 M-5Y51 processor
●Intel Core i3 M-5Y10c processor
Chipset Intel soldered-on chipset (SoC)
Graphics Intel HD unified memory architecture (UMA) Graphics
Panel 11.6-in, TouchScreen, full-high definition (FHD), BrightView (BV), (1920×1080), in-plane switching
(IPS), 50% CG, typical brightness 400 nits, eDP 1.3, ultra-slim with and without digitizer
11.6-in, TouchScreen, high definition (HD), BV, (1366×768), IPS, 50% CG, typical brightness 400 nits,
eDP 1.2, ultra-slim with and without digitizer
Memory 2 SODIMM slots DDR3L-1600MHz
Support for DDR3L-1600MHz
Support for dual channel
Supports up to 8192-MB maximum system memory
Supports 8192-MB (16-GB, 256-MB×16×4, qty 4) and 4096-MB (8-GB @ 128-MB×32×2, qty 4)
memory configurations
Primary storage Support for M2 solid-state drive, SS 2280
Support for the following solid-state drives:
●512-GB, M2, SATA-3 solid-state drive
●256-GB, M2, SATA-3 solid-state drive
●256-GB, M2, SATA-3 solid-state drive supporting triple-level cell (TLC)
●256-GB, M2, SATA-3 self-encrypting drive (SED) solid-state drive supporting Opal 2
●256-GB, M2, SanDisk X110 locked solid-state drive
●180-GB, M2, SATA-3 solid-state drive
●180-GB, M2, SATA-3 SED solid-state drive supporting Opal 2
●128-GB, M2, SATA-3 solid-state drive
●128-GB, M2, SATA-3 solid-state drive supporting TLC
Audio and video 2.0-MP (1080p) front-facing webcam
5.0-MP (1080p) rear-facing webcam
Dual array microphones
HD audio with DTS Studio Sound
Stereo speakers (2)
Wireless Integrated wireless local area network (WLAN) options by way of wireless module
1
Category Description
Wireless (continued) One built-in WLAN antenna (in display panel assembly)
Support for the following WLAN modules:
●Intel 7265.NGWGQ.I 2 ac 2×2 + Bluetooth 4.0 LE PCIe+USB NGFF 2230 Combo Adapter
●Intel Tri Band Wireless-AC 17265 802.11a/b/g/n/ac 2×2 and Bluetooth 4.0 + WiGig
Combo Adapter
●Intel Dual Band Wireless-AC 7265 802.11a/b/g/n/ac 2×2 WiFi and Bluetooth 4.0
Combo Adapter
●Intel Dual Band Wireless-AN 7265 802.11a/b/g/n 2×2 and Bluetooth 4.0 Combo Adapter
Integrated wireless personal area network (WPAN) options supported only through Bluetooth 4.0
combination card
Integrated wireless wide area network (WWAN) options by way of wireless module
Two built-in WWAN antennas (in display panel assembly)
Support for the following WWAN modules:
●HP lt4226 LTE/HSPA+ 4G Module
●HP lt4225 LTE/EV-DO 4G Module
●HP lt4211 LTE/EV-DO/HSPA+ 4G Module
●HP lt4112 LTE/HSPA+ 4G Module
●HP hs3110 HSPA+ Mobile Broadband Module
External media cards HP multiformat Micro Digital Media Reader Slot with push-push technology. Reads data from and
writes data to digital memory cards such as Secure Digital (SD).
Ports Slate:
●Audio: one combo audio-out (headphone)/audio-in (microphone) jack, supports jack auto-
detection
●Docking (via dongle)
●Micro SD card
●Micro SIM
Keyboard base:
●Audio: one combo audio-out (headphone)/audio-in (microphone) jack, supports jack auto-
detection
●DisplayPort 1.2
●Docking (via dongle)
●HP Smart AC adapter (4.5-mm barrel)
●Smart card
●USB 3.0 (2: charging and non-charging)
Keyboard/pointing devices Spill-resistant keyboard with drain
Backlit
Touchpad requirements:
●ForcePad
●Glass with chemical etched surface
2 Chapter 1 Product description
Category Description
Keyboard/pointing devices
(continued)
●Supports two-way scroll
●Gestures enabled by default: 2-finger scrolling, 2-finger zoom (pinch)
Power requirements Support for the following AC adapters:
●65-W HP Smart adapter (non-PFC, 3-wire) and 45-W HP Smart adapter (non-PFC, RC, 3-wire)
●65-W HP Smart travel adapter (non-PFC)
●45-W ElitePad HP Smart adapter (4.5-mm)
●45-W HP Smart adapter (non-PFC, RC, 4.5-mm)
●45-W HP Smart adapter (non-PFC, RC, 4.5-mm, 2-wire)
Support for the following batteries:
Keyboard base: 6-cell, 21-WHr, 0.95-AHr, LI battery (includes cable)
Slate: 2-cell, 33-WHr, 4.56-AHr, LI battery (includes cable)
Security Fingerprint reader
Trusted Platfom Module (TPM) 1.2 / 2.0 (Infineon, soldered)
Integrated Smart card reader (active)
Full-volume encryption
Preboot authentication (password, smart card)
Operating system Preinstalled:
Windows 10:
●Windows 10 Home 64-bit (not available on computer models equipped with an FHD display
assembly and more than or equal 8.0-GB of system memory)
●Windows 10 Home Chinese Market 64-bit (not available on computer models equipped with an
FHD display assembly and more than or equal 8.0-GB of system memory)
●Windows 10 Home Chinese Market CPPP 64-bit (only available with People’s Republic of China
Country Loc)
●Windows 10 Home Chinese Market High End 64-bit (only available on computer models
equipped with an FHD display assembly and more than or equal 8.0-GB of system memory)
●Windows 10 Home High End 64-bit (only available on computer models equipped with an FHD
display assembly and more than or equal 8.0-GB of system memory)
●Windows 10 Home Single Language 64-bit (not available on computer models equipped with
an FHD display assembly and more than or equal 8.0-GB of system memory)
●Windows 10 Home Single Language High End 64-bit (only available on computer models
equipped with an FHD display assembly and more than or equal 8.0-GB of system memory)
●Windows 10 Professional 64-bit
●Windows 10 Professional 64-bit with Windows 7 Professional 64-bit image
Windows 8.1:
●Windows 8.1 Chinese 64-bit (only available with People’s Republic of China Country Loc; not
available on computer models equipped with an Intel i7 processor and more than 4.0-GB of
system memory and computer models equipped with an FHD display assembly and more than
or equal 8.0-GB of system memory)
●Windows 8.1 Emerging Markets 64-bit (not available on computer models equipped with an
Intel i7 processor and more than 4.0-GB of system memory and computer models equipped
with an FHD display assembly and more than or equal 8.0-GB of system memory)
3
Category Description
Operating system (continued) ●Windows 8.1 Emerging Markets 64-bit High End (only available on computer models equipped
with an FHD display assembly and more than or equal 8.0-GB of system memory)
●Windows 8.1 Multi-language 64-bit (not available on computer models equipped with an Intel
i7 processor and more than 4.0-GB of system memory and computer models equipped with an
FHD display assembly and more than or equal 8.0-GB of system memory)
●Windows 8.1 Multi-language 64-bit High End (only available on computer models equipped
with an FHD display assembly and more than or equal 8.0-GB of system memory)
●Windows 8.1 Professional 64-bit
●Windows 8.1 Professional 64-bit – MSNA
●Windows 8.1 Professional 64-bit for Education
●Windows 8.1 Professional 64-bit with Windows 7 Professional 64-bit image
●Windows 8.1 Professional 64-bit with Windows 7 Professional 64-bit image – MSNA
Windows 7 Professional 64-bit – MSNA
FreeDOS 2.0
Restore media – DRDVD:
●DRDVD Windows 10 (available with any Windows 10 operating system, required with any
Windows 10 downgrade operating system)
●DRDVD Windows 8.1 (available with any Windows 8.1 loc, required with any Windows 8.1
Professional downgrade operating system)
●DRDVD Windows 7 (available with any Windows 10 Professional, Windows 8.1 Professional, or
Windows 7 downgrade loc)
OSDVD:
●Windows 10 OSDVD Downgrade RTF (required with any Windows 10 Downgrade operating
system)
●Windows 8.1 64-bit (update, for service only)
●Windows 8.1 Country–specific 64-bit (update, for service only)
●Windows 8.1 Emerging Markets 64-bit (update, for service only)
●Windows 8.1 Professional 64-bit (update, only available and required with Windows 8.1
Downgrade operating system. Do not include for Asia Pacific countries and regions and the
People’s Republic of China)
●Windows 8.1 Professional 64-bit for Education (update, for service only)
●Windows 7 Professional 64-bit (available with any Windows 10 Professional, Windows 8.1
Professional, or Windows 7 Professional downgrade except in Asia Pacific countries and
regions and the People’s Republic of China)
Certified: Microsoft WHQL
Web-only support:
●Windows 10 Enterprise
●Windows 8.1 Enterprise 64-bit
●Windows 8 Chinese Market 64-bit
●Windows 8 Emerging Markets 64-bit
●Windows 8 Multi-language 64-bit
●Windows 8 Professional 64-bit
4 Chapter 1 Product description
Category Description
Operating system (continued) ●Windows 7 Enterprise 64-bit
●Windows 7 Enterprise 32-bit
●Windows 7 Professional 32-bit
Serviceability End user replaceable parts: AC adapter
5
2 External component identification
Slate edge components
Item Component Description
(1) Internal microphone Record sound.
(2) Vents Enable airflow to cool internal components.
NOTE: The slate fan starts up automatically to cool internal
components and prevent overheating. It is normal for
the internal fan to cycle on and off during routine operation.
(3) Rear-facing webcam Records video and captures photographs. Some models
allow you to video conference and chat online using
streaming video.
For information on using the webcam:
●Windows 10 – Type camera in the taskbar search box,
and then select Camera.
●Windows 8 – Access HP Support Assistant. To access HP
Support Assistant on the Start screen, select the HP
Support Assistant app.
●Windows 7 – Select Start > All Programs >
Communication and Chat > HP WebCam.
(4) Camera flash Provides light for rear-facing webcam photos.
(5) Rotate lock button When the slate is on, press the rotate lock button to lock
the autorotate feature of the display. To unlock
the autorotate feature, press the button again.
(6) Volume button Controls speaker volume on the slate.
6 Chapter 2 External component identification
Item Component Description
●To increase speaker volume, press the + edge of
the button.
●To decrease speaker volume, press the – edge of
the button.
(7) Pen holder (select models only) Holds the digital pen.
(8) Alignment post connectors (2) Align and attach the slate to the keyboard.
(9) Docking/adapter port Connects the slate to the keyboard, or as a slate only,
connects an optional adapter.
(10) Audio-out (headphone)/Audio-in (microphone) jack Connects optional powered stereo speakers, headphones,
earbuds, a headset, or a television audio cable. Also connects
an optional headset microphone. This jack does not support
optional microphone-only devices.
NOTE: When a device is connected to the jack, the slate
speakers are disabled.
NOTE: Be sure that the device cable has a 4-conductor
connector that supports both audio-out (headphone) and
audio-in (microphone).
WARNING! To reduce the risk of personal injury, adjust
the volume before putting on headphones, earbuds, or a
headset. For additional safety information, see
the Regulatory, Safety, and Environmental Notices.
To access this guide:
Windows 10:
Select the Start button, select All apps, select HP Help and
Support, and then select HP Documentation.
Windows 8 or Windows 7:
▲Select the HP Support Assistant app on the Start
screen, select My computer, and then select User
guides.
(11) SIM/SD card release access A pinhole for use in ejecting the door covering the SIM and SD
card slots.
(12) SIM Card slot (select models only) A slot for a SIM card.
NOTE: This feature is available on select models only.
(13) Micro SD memory card reader Reads optional memory cards that store, manage, share, or
access information.
To insert a card:
Hold the card label-side up, with connectors facing the slot,
insert the card into the slot, and then push in on the card until
it is firmly seated.
To remove a card:
Press in on the card it until it pops out.
(14) Power button ●When the slate is off, press the button to turn on
the slate.
●When the slate is on, press the button briefly to initiate
Sleep.
Slate edge components 7
Item Component Description
●When the slate is in the Sleep state, press the button
briefly to exit Sleep.
●When the slate is in Hibernation, press the button
briefly to exit Hibernation.
CAUTION: Pressing and holding down the power button will
result in the loss of unsaved information.
If the slate has stopped responding and Windows shutdown
procedures are ineffective, press and hold the power button
for at least 15 seconds to turn off the slate.
NOTE: For select models, the Intel Rapid Start Technology
feature is enabled at the factory. Rapid Start Technology
allows your slate to resume quickly from inactivity.
To learn more about your power settings:
Windows 10: Type power in the taskbar search box, and
then select Power and sleep settings.
– or –
Right-click the Start button, and then select Power Options.
Windows 8: See your power options. From the Start screen,
type power, select Settings, and then select Power Options.
Windows 7: See your power options. Select Start > Control
Panel > System and Settings > Power Options.
Linux:
1. Select Computer > Control Center.
2. In the left pane, click System, and then click Power
Management in the right pane.
8 Chapter 2 External component identification
Slate display components
Item Component Description
(1) WLAN antenna* Sends and receives wireless signals to communicate
with WLANs.
(2) WWAN antennas (2)* Send and receive wireless signals to communicate
with WWANs.
(3) Webcam light On: The webcam is in use.
(4) Front-facing webcam Records video and captures photographs. Some models
allow you to video conference and chat online using
streaming video.
For information on using the webcam:
●Windows 10 – Type camera in the taskbar search box,
and then select Camera.
●Windows 8 – Access HP Support Assistant. To access HP
Support Assistant on the Start screen, select the HP
Support Assistant app.
●Windows 7 – Select Start > All Programs >
Communication and Chat > HP WebCam.
(5) WiGig antenna* Sends and receives wireless signals.
(6) Ambient light sensor Automatically adjusts the display brightness based on
the lighting conditions in your environment.
(7) Internal microphone Record sound.
(8) Speakers (2) Produce sound.
Slate display components 9
Item Component Description
(9) Windows button Displays the Windows Start menu.
*The antennas are not visible on the outside of the computer. For optimal transmission, keep the areas immediately around the
antennas free from obstructions.
For wireless regulatory notices, see the section of the Regulatory, Safety, and Environmental Notices that applies to your country or
region.
To access this guide:
Windows 10:
Select the Start button, select All apps, select HP Help and Support, and then select HP Documentation.
Windows 8 or Windows 7:
▲Select the HP Support Assistant app on the Start screen, select My computer, and then select User guides.
10 Chapter 2 External component identification
Keyboard base
Item Component Description
(1) Alignment posts (2) Align and attach the slate to the keyboard.
(2) Docking connector Connects the slate to the keyboard.
CAUTION: To prevent damage to the docking connector, do
not touch the connector when the slate is detached from
the keyboard.
(3) Release latch Releases the slate from the keyboard. To release the slate,
press the release latch.
(4) Fingerprint reader (select models only) Allows a fingerprint logon to Windows, instead of a
password logon.
Keyboard base 11
Keys
Item Component Description
(1) esc key Displays system information when pressed in combination
with the fn key.
(2) Function keys Execute frequently used system functions when pressed in
combination with the fn key.
NOTE: Function keys do not display or function from
the on-screen slate keyboard.
(3) num lock key Turns the embedded numeric keypad on and off when
pressed in combination with the fn key.
(4) fn key Executes frequently used system functions when pressed in
combination with a function key, the num lock key, or
the esc key.
(5) Windows key Displays the Windows Start menu.
(6) Embedded numeric keypad When num lock has been enabled, it can be used like an
external numeric keypad.
Each key on the keypad performs the function indicated by
the icon in the upper-right corner of the key.
12 Chapter 2 External component identification
Lights
Item Component Description
(1) Caps lock light On: Caps lock is on, which switches the keys to all
capital letters.
(2) TouchPad light ●On: The TouchPad is off.
●Off: The TouchPad is on.
(3) Mute light ●Amber: Slate sound is off.
●Off: Slate sound is on.
(4) Microphone mute light ●Amber: microphone sound is off.
●Off: microphone sound is on.
(5) Wireless light On: An integrated wireless device, such as a wireless local
area network (WLAN) device and/or a Bluetooth device, is on.
NOTE: On some models, the wireless light is amber when
all wireless devices are off.
(6) Num lock light On: Num lock is on.
Lights 13
TouchPad
Item Component Description
(1) TouchPad zone Moves the pointer and selects or activates items on
the screen.
(2) Left TouchPad button Functions like the left button on an external mouse.
(3) Right TouchPad button Functions like the right button on an external mouse.
14 Chapter 2 External component identification
Left side
Item Component Description
(1) Volume button Controls speaker volume on the slate.
●To increase speaker volume, press the + edge of
the button.
●To decrease speaker volume, press the – edge of
the button.
(2) LCD rotation lock button Locks orientation of the display, preventing
automatic rotation.
(3) Docking/adapter port Connects the slate to the keyboard, or as a slate only,
connects an optional adapter.
(4) USB 3.0 port Connects an optional USB device, such as a keyboard, mouse,
external drive, printer, scanner or USB hub.
(5) Audio-out (headphone)/Audio-in (microphone) jack Connects optional powered stereo speakers, headphones,
earbuds, a headset, or a television audio cable. Also connects
an optional headset microphone. This jack does not support
optional microphone-only devices.
NOTE: When a device is connected to the jack, the slate
speakers are disabled.
NOTE: Be sure that the device cable has a 4-conductor
connector that supports both audio-out (headphone) and
audio-in (microphone).
WARNING! To reduce the risk of personal injury, adjust
the volume before putting on headphones, earbuds, or a
headset. For additional safety information, see
the Regulatory, Safety, and Environmental Notices.
To access this guide:
Windows 10:
Select the Start button, select All apps, select HP Help and
Support, and then select HP Documentation.
Windows 8 or Windows 7:
Left side 15
Item Component Description
▲Select the HP Support Assistant app on the Start
screen, select My computer, and then select User
guides.
(6) Smart card reader Supports optional Smart cards.
Right side
Item Component Description
(1) Internal microphone Records sound.
(2) Power button ●When the slate is off, press the button to turn on
the slate.
●When the slate is on, press the button briefly to initiate
Sleep.
●When the slate is in the Sleep state, press the button
briefly to exit Sleep.
●When the slate is in Hibernation, press the button
briefly to exit Hibernation.
CAUTION: Pressing and holding down the power button will
result in the loss of unsaved information.
If the slate has stopped responding and Windows shutdown
procedures are ineffective, press and hold the power button
for at least 5 seconds to turn off the slate.
NOTE: For select models, the Intel Rapid Start Technology
feature is enabled at the factory. Rapid Start Technology
allows your slate to resume quickly from inactivity.
To learn more about your power settings:
Windows 10: Type power in the taskbar search box, and
then select Power and sleep settings.
– or –
Right-click the Start button, and then select Power Options.
16 Chapter 2 External component identification
Item Component Description
Windows 8: See your power options. From the Start screen,
type power, select Settings, and then select Power Options.
Windows 7: See your power options. Select Start > Control
Panel > System and Settings > Power Options.
Linux:
1. Select Computer > Control Center.
2. In the left pane, click System, and then click Power
Management in the right pane.
(3) Micro SD memory card reader Reads optional memory cards that store, manage, share, or
access information.
To insert a card:
Hold the card label-side up, with connectors facing the slot,
insert the card into the slot, and then push in on the card until
it is firmly seated.
To remove a card:
Press in on the card it until it pops out.
(4) SIM Card slot (select models only) A slot for a SIM card.
(5) SIM/SD card release access A pinhole for use in ejecting the door covering the SIM and SD
card slots.
(6) USB 3.0 charging (powered) port Connects an optional USB device, such as a keyboard, mouse,
external drive, printer, scanner or USB hub. Standard USB
ports will not charge all USB devices or will charge using a
low current. Some USB devices require power and require you
to use a powered port.
NOTE: USB charging ports can also charge select models of
cell phones and MP3 players, even when the slate is off.
(7) Dual-Mode DisplayPort Connects an optional digital display device, such as a high-
performance monitor or projector.
(8) AC adapter/battery light ●White: The slate is connected to external power and
the battery is charged from 90 to 99 percent.
●Amber: The slate is connected to external power and
the battery is charged from 0 to 90 percent.
●Blinking amber: A battery that is the only available
power source has reached a low battery level. When
the battery reaches a critical battery level, the battery
light begins blinking rapidly.
●Off: The battery is fully charged.
(9) Power connector Connects an AC adapter.
*The antennas are not visible on the outside of the computer. For optimal transmission, keep the areas immediately around the
antennas free from obstructions.
For wireless regulatory notices, see the section of the Regulatory, Safety, and Environmental Notices that applies to your country or
region.
To access this guide:
Windows 10:
Select the Start button, select All apps, select HP Help and Support, and then select HP Documentation.
Right side 17
Item Component Description
Windows 8 or Windows 7:
▲Select the HP Support Assistant app on the Start screen, select My computer, and then select User guides.
18 Chapter 2 External component identification
3 Illustrated parts catalog
NOTE: HP continually improves and changes product parts. For complete and current information on
supported parts for your slate, go to http://partsurfer.hp.com, select your country or region, and then follow
the on-screen instructions.
Locating the product name, serial number, product number,
warranty information, and model name
The product name (1), serial number (2), product number (3), warranty information (4), and model name (5)
are located on the bottom of the slate. You may need this information when you travel internationally or
when you contact support.
Locating the product name, serial number, product number, warranty information, and model name 19
Slate major components
Item Component Spare part number
(1) 11.6-in, TouchScreen display panel assembly:
FHD, BV, (1920×1080), IPS, 50% CG, typical brightness 400 nits, eDP 1.3, ultra-slim
with digitizer
793736-001
FHD, BV, (1920×1080), IPS, 50% CG, typical brightness 400 nits, eDP 1.3, ultra-slim
without digitizer
804352-001
HD, BV, (1366×768), IPS, 50% CG, typical brightness 400 nits, eDP 1.2, ultra-slim
with digitizer
793737-001
HD, BV, (1366×768), IPS, 50% CG, typical brightness 400 nits, eDP 1.2, ultra-slim
without digitizer
804351-001
Speaker grille (not illustrated; 2 pieces, includes double-sided adhesive) 793734-001
(2) RTC battery (includes cable and double-sided adhesive) 793723-001
20 Chapter 3 Illustrated parts catalog
Item Component Spare part number
(3) Volume button board bracket: Included in the Slate Bracket Kit, spare part number 793728-001.
(4) Heat sink (includes replacement thermal material) 793726-001
(5) Front-facing webcam (includes double-sided adhesive): Included in the Webcam Kit, spare part number 793724-001.
NOTE: The front-facing webcam spare part kit does not include the front-facing webcam cable. The front-facing
webcam cable is included in the Slate Cable Kit, spare part number 793721-001.
(6) Rear-facing webcam: Included in the Webcam Kit, spare part number 793724-001.
NOTE: The rear-facing webcam spare part kit does not include the rear-facing webcam cable. The rear-facing webcam
cable is included in the Slate Cable Kit, spare part number 793721-001.
(7) Volume button board
NOTE: The volume button board spare part kit does not include the volume button board
cable. The volume button board cable is included in the Slate Cable Kit, spare part number
793721-001.
793733-001
(8) Fan (includes cable) 793735-001
(9) WWAN module:
HP lt4226 LTE/HSPA+ 4G Module 736675-005
HP lt4225 LTE/EV-DO 4G Module 793736-005
HP lt4211 LTE/EV-DO/HSPA+ 4G Module 793116-005
HP lt4112 LTE/HSPA+ 4G Module 790198-005
HP hs3110 HSPA+ Mobile Broadband Module 793516-005
(10) WLAN module:
Intel 7265.NGWGQ.I 2 ac 2×2 + Bluetooth 4.0 LE PCIe+USB NGFF 2230 Combo Adapter 783721-005
Intel Tri Band Wireless-AC 17265 802.11a/b/g/n/ac 2×2 and Bluetooth 4.0 + WiGig
Combo Adapter
806724-005
Intel Dual Band Wireless-AC 7265 802.11a/b/g/n/ac 2×2 WiFi and Bluetooth 4.0
Combo Adapter
756749-005
Intel Dual Band Wireless-AN 7265 802.11a/b/g/n 2×2 and Bluetooth 4.0 Combo Adapter 756748-005
(11) Display panel cable (includes double-sided adhesive) 804344-001
(12) System board (includes a graphics subsystem with UMA memory and replacement thermal material):
Equipped with an Intel Core i7 M-5Y71 processor, 8.0-GB of system memory,
and the Windows 10 or Windows 8 Professional operating system
805071-601
Equipped with an Intel Core i7 M-5Y71 processor, 8.0-GB of system memory,
and the Windows 10 or Windows 8 Standard operating system
805071-501
Equipped with an Intel Core i7 M-5Y71 processor, 8.0-GB of system memory, and a non-
Windows operating system
805071-001
Equipped with an Intel Core i7 M-5Y71 processor, 4.0-GB of system memory,
and the Windows 10 or Windows 8 Professional operating system
805072-601
Equipped with an Intel Core i7 M-5Y71 processor, 4.0-GB of system memory,
and the Windows 10 or Windows 8 Standard operating system
805072-501
Equipped with an Intel Core i7 M-5Y71 processor, 4.0-GB of system memory, and a non-
Windows operating system
805072-001
Slate major components 21
Item Component Spare part number
Equipped with an Intel Core i5 M-5Y51 processor, 8.0-GB of system memory,
and the Windows 10 or Windows 8 Professional operating system
805070-601
Equipped with an Intel Core i5 M-5Y51 processor, 8.0-GB of system memory,
and the Windows 10 or Windows 8 Standard operating system
805070-501
Equipped with an Intel Core i5 M-5Y51 processor, 8.0-GB of system memory, and a non-
Windows operating system
805070-001
Equipped with an Intel Core i5 M-5Y51 processor, 4.0-GB of system memory,
and the Windows 10 or Windows 8 Professional operating system
805069-601
Equipped with an Intel Core i5 M-5Y51 processor, 4.0-GB of system memory,
and the Windows 10 or Windows 8 Standard operating system
805069-501
Equipped with an Intel Core i5 M-5Y51 processor, 4.0-GB of system memory, and a non-
Windows operating system
805069-001
Equipped with an Intel Core i3 M-5Y10c processor, 4.0-GB of system memory,
and the Windows 10 or Windows 8 Professional operating system
805068-601
Equipped with an Intel Core i3 M-5Y10c processor, 4.0-GB of system memory,
and the Windows 10 or Windows 8 Standard operating system
805068-501
Equipped with an Intel Core i3 M-5Y10c processor, 4.0-GB of system memory, and a non-
Windows operating system
805068-001
(13) Solid-state drive:
512-GB, M2, SATA-3 solid-state drive 811391-001
256-GB, M2, SATA-3 793709-001
256-GB, M2, SATA-3 solid-state drive supporting TLC 811393-001
256-GB, M2, SATA-3, SED solid-state drive supporting Opal 2 810987-001
256-GB, M2, SanDisk X110 locked solid-state drive 824109-001
180-GB, M2, SATA-3 811389-001
180-GB, M2, SATA-3, SED solid-state drive supporting Opal 2 811390-001
128-GB, M2, SATA-3 793708-001
128-GB, M2, SATA-3 solid-state drive supporting TLC 811392-001
(14) Battery, 2-cell, 33-WHr, 4.56-AHr, LI (includes cable) 750549-005
(15) Speakers (includes left and right speakers and cables) 793729-001
(16) Vibrator module (includes left and right vibrator modules and cables) 793730-001
(17) Alignment bracket, left: Included in the Slate Bracket Kit, spare part number 793728-001.
(18) Docking connector bracket: Included in the Slate Bracket Kit, spare part number 793728-001.
(19) Alignment bracket, right: Included in the Slate Bracket Kit, spare part number 793728-001.
Antenna Kit, includes:
(20) WiGig antenna cable and transceiver (for use only on slate models equipped with
WiGig capability)
805066-001
(21) WWAN main and auxiliary cables and transceivers
(22) WLAN antenna cable and transceiver
22 Chapter 3 Illustrated parts catalog
Item Component Spare part number
For use in African, European, and Middle Eastern countries and regions 805065-001
For use in Japan 806251-001
For use in North America 805067-001
(23) Docking connector board
NOTE: The docking connector board spare part kit does not include the docking connector
board cable. The docking connector board cable is included in the Slate Cable Kit, spare part
number 793721-001.
793731-001
(24) Audio jack board (includes cable) 793732-001
(25) Docking connector board cable: Included in the Slate Cable Kit, spare part number 793721-001.
(26) Back cover 793725-001
Slate major components 23
Keyboard base
Item Description Spare part number
(1) Keyboard (includes keyboard cable and keyboard backlight cable):
For use in Belgium 793738-A41
For use in Brazil 793738-201
For use in Bulgaria 793738-261
For use in Canada 793738-DB1
For use in the Czech Republic and Slovakia 793738-FL1
For use in Denmark 793738-081
For use in France 793738-051
For use in Germany 793738-041
24 Chapter 3 Illustrated parts catalog
Item Description Spare part number
For use in Greece 793738-151
For use in Hungary 793738-211
For use in Iceland 793738-DD1
For use in India 793738-D61
For use in Israel 793738-BB1
For use in Italy 793738-061
For use in Japan 793738-291
For use in Latin America 793738-161
For use in the Netherlands 793738-B31
For use in Northwest Africa 793738-FP1
For use in Norway 793738-091
For use in Portugal 793738-131
For use in Romania 793738-271
For use in Russia 793738-251
For use in Saudi Arabia 793738-171
For use in Slovenia 793738-BA1
For use in South Korea 793738-AD1
For use in Spain 793738-071
For use in Sweden and Finland 793738-B71
For use in Switzerland 793738-111
For use in Taiwan 793738-AB1
For use in Thailand 793738-281
For use in Turkey 793738-141
For use in the United Kingdom and Singapore 793738-031
For use in the United States 793738-001
(2) Top cover 793718-001
(3) TouchPad (includes cable) 793720-001
(4) Fingerprint reader board
NOTE: The fingerprint reader board spare part kit does not include the fingerprint reader
board cable. The fingerprint reader board cable is included in the Keyboard Base Cable Kit,
spare part number 793721-001.
793713-001
(5) Connector board (includes USB port and DisplayPort)
NOTE: The connector board spare part kit does not include the connector board cable.
The connector board cable is included in the Keyboard Base Cable Kit, spare part number
793721-001.
804350-001
(6) Smart card reader board 793711-001
Keyboard base 25
Item Description Spare part number
NOTE: The smart card reader board spare part kit does not include the smart card reader
board cable. The smart card reader board cable is included in the Keyboard Base Cable Kit,
spare part number 793721-001.
(7) Battery, 6-cell, 21-WHr, 0.95-AHr, LI (includes cable) 750550-005
(8) Power connector cable 793714-001
(9) Keyboard base system board (includes docking/adapter port, USB port, and audio jack) 806252-001
(10) Hinge assembly (includes left and right cables) 793717-001
(11) Kickstand (includes rubber feet) 793715-001
Kickstand Hinge Kit (not illustrated) 793716-001
(12) Bottom cover 793710-001
Rubber Kit (not illustrated, includes bottom cover rubber feet) 804348-001
Miscellaneous parts
Component Spare part number
AC adapter:
65-W HP Smart adapter (non-PFC, EM, 4.5-mm) 714657-001
65-W HP Smart travel adapter (non-PFC) 693716-001
45-W ElitePad HP Smart adapter (4.5-mm) 790129-001
45-W HP Smart adapter (non-PFC, RC, 4.5-mm) 741727-001
45-W HP Smart adapter (non-PFC, RC, 4.5-mm, 2-wire) 742436-001
Bracket Kit:
For use on the keyboard base, includes:
●Connector board cable
●Fingerprint reader board cable
●Smart card reader board cable
793712-001
For use on the slate, includes:
●Alignment guide left bracket
●Alignment guide right bracket
●Docking connector board bracket
●Volume button board bracket
793728-001
Cable Kit:
For use on the keyboard base, includes:
●Connector board cable
●Fingerprint reader board cable
●Smart card reader board cable
793719-001
26 Chapter 3 Illustrated parts catalog
Component Spare part number
For use on the slate, includes:
●Digitizer board cable
●Docking connector board cable
●Front-facing webcam cable
●Rear-facing webcam cable
●TouchScreen cable
●Volume button board cable
793721-001
Digitizer pen 804346-001
Travel keyboard:
For use Belgium 800577-A41
For use in Brazil 800577-201
For use in Bulgaria 800577-261
For use in the Czech Republic and Slovakia 800577-FL1
For use in Denmark 800577-081
For use in Denmark, Finland, and Norway 800577-DH1
For use in France 800577-051
For use in Germany 800577-041
For use in Greece 800577-151
For use in Hungary 800577-211
For use in Iceland 800577-DD1
For use in India 800577-D61
For use in Israel 800577-BB1
For use in Italy 800577-061
For use in Japan 800577-291
For use in Latin America 800577-161
For use in the Netherlands 800577-B31
For use in North Africa 800577-FP1
For use in Norway 800577-091
For use in Portugal 800577-131
For use in Romania 800577-271
For use in Russia 800577-251
For use in Saudi Arabia 800577-171
For use in Slovenia 800577-BA1
For use in South Korea 800577-AD1
For use in Spain 800577-071
Miscellaneous parts 27
Component Spare part number
For use in Sweden and Finland 800577-B71
For use in Switzerland 800577-111
For use in Taiwan 800577-AB1
For use in Thailand 800577-281
For use in Turkey 800577-141
For use in the United Kingdom and Singapore 800577-031
For use in the United States 800577-001
Plastics Kit for use on the slate, includes:
●Power button actuator
●Rotate lock button actuator
●SD card/SIM cover
●Volume button actuator
804347-001
Power cord, 3-pin, black, 1.83-m:
For use in Argentina 490371-D01
For use in Australia 490371-011
For use in Brazil 490371-202
For use in Denmark 490371-081
For use in Europe 490371-021
For use in India 490371-D61
For use in Israel 490371-BB1
For use in Italy 490371-061
For use in Japan 490371-291
For use in North America 490371-001
For use in the People's Republic of China 490371-AA1
For use in South Africa 490371-AR1
For use in South Korea 490371-AD1
For use in Switzerland 490371-111
For use in Taiwan 490371-AB1
For use in Thailand 490371-201
For use in the United Kingdom and Singapore 490371-031
Power cord, 3-pin, black, 1.00-m:
For use in Argentina 755530-D01
For use in Australia 755530-011
For use in Brazil 755530-202
28 Chapter 3 Illustrated parts catalog
Component Spare part number
For use in Denmark 755530-081
For use in Europe 755530-021
For use in India 755530-D61
For use in Israel 755530-BB1
For use in Italy 755530-061
For use in Japan 755530-291
For use in North America 755530-001
For use in the People's Republic of China 755530-AA1
For use in South Africa 755530-AR1
For use in South Korea 755530-AD1
For use in Switzerland 755530-111
For use in Taiwan 755530-AB1
For use in Thailand 755530-201
For use in the United Kingdom and Singapore 755530-031
Power cord, 2-pin, black, 1.00-m, for use in Japan 762689-291
Screw Kit:
For use on the keyboard base 804349-001
For use on the slate 793727-001
Miscellaneous parts 29
4 Removal and replacement preliminary
requirements
Tools required
You will need the following tools to complete the removal and replacement procedures:
●Flat-bladed screw driver
●Magnetic screw driver
●Phillips P0 screw driver
Service considerations
The following sections include some of the considerations that you must keep in mind during disassembly
and assembly procedures.
NOTE: As you remove each subassembly from the slate, place the subassembly (and all accompanying
screws) away from the work area to prevent damage.
Plastic parts
CAUTION: Using excessive force during disassembly and reassembly can damage plastic parts. Use care
when handling the plastic parts. Apply pressure only at the points designated in the
maintenance instructions.
Cables and connectors
CAUTION: When servicing the slate, be sure that cables are placed in their proper locations during the
reassembly process. Improper cable placement can damage the slate.
Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or
seat the cables during removal and insertion. Handle cables by the connector whenever possible. In all cases,
avoid bending, twisting, or tearing cables. Be sure that cables are routed in such a way that they cannot be
caught or snagged by parts being removed or replaced. Handle flex cables with extreme care; these cables
tear easily.
30 Chapter 4 Removal and replacement preliminary requirements
Grounding guidelines
Electrostatic discharge damage
Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure
determine the degree of sensitivity. Networks built into many integrated circuits provide some protection,
but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions.
A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or
microcircuitry. Even if the spark is neither felt nor heard, damage may have occurred.
An electronic device exposed to ESD may not be affected at all and can work perfectly throughout a normal
cycle. Or the device may function normally for a while, then degrade in the internal layers, reducing its life
expectancy.
CAUTION: To prevent damage to the slate when you are removing or installing internal components,
observe these precautions:
Keep components in their electrostatic-safe containers until you are ready to install them.
Before touching an electronic component, discharge static electricity by using the guidelines described in this
section.
Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.
If you remove a component, place it in an electrostatic-safe container.
The following table shows how humidity affects the electrostatic voltage levels generated by
different activities.
CAUTION: A product can be degraded by as little as 700 V.
Typical electrostatic voltage levels
Relative humidity
Event 10% 40% 55%
Walking across carpet 35,000 V 15,000 V 7,500 V
Walking across vinyl floor 12,000 V 5,000 V 3,000 V
Motions of bench worker 6,000 V 800 V 400 V
Removing DIPS from plastic tube 2,000 V 700 V 400 V
Removing DIPS from vinyl tray 11,500 V 4,000 V 2,000 V
Removing DIPS from Styrofoam 14,500 V 5,000 V 3,500 V
Removing bubble pack from PCB 26,500 V 20,000 V 7,000 V
Packing PCBs in foam-lined box 21,000 V 11,000 V 5,000 V
Grounding guidelines 31
Packaging and transporting guidelines
Follow these grounding guidelines when packaging and transporting equipment:
●To avoid hand contact, transport products in static-safe tubes, bags, or boxes.
●Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging.
●Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.
●Place items on a grounded surface before removing items from their containers.
●Always be properly grounded when touching a component or assembly.
●Store reusable ESD-sensitive parts from assemblies in protective packaging or nonconductive foam.
●Use transporters and conveyors made of antistatic belts and roller bushings. Be sure that mechanized
equipment used for moving materials is wired to ground and that proper materials are selected to avoid
static charging. When grounding is not possible, use an ionizer to dissipate electric charges.
Workstation guidelines
Follow these grounding workstation guidelines:
●Cover the workstation with approved static-shielding material.
●Use a wrist strap connected to a properly grounded work surface and use properly grounded tools and
equipment.
●Use conductive field service tools, such as cutters, screw drivers, and vacuums.
●When fixtures must directly contact dissipative surfaces, use fixtures made only of static-
safe materials.
●Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids
and Styrofoam.
●Handle ESD-sensitive components, parts, and assemblies by the case or PCM laminate. Handle these
items only at static-free workstations.
●Avoid contact with pins, leads, or circuitry.
●Turn off power and input signals before inserting or removing connectors or test equipment.
32 Chapter 4 Removal and replacement preliminary requirements
Equipment guidelines
Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation.
●When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a
minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap
snugly against the skin at all times. On grounded mats with banana-plug connectors, use alligator clips
to connect a wrist strap.
●When standing, use foot straps and a grounded floor mat. Foot straps (heel, toe, or boot straps) can be
used at standing workstations and are compatible with most types of shoes or boots. On conductive
floors or dissipative floor mats, use foot straps on both feet with a minimum of one megohm resistance
between the operator and ground. To be effective, the conductive must be worn in contact with the
skin.
The following grounding equipment is recommended to prevent electrostatic damage:
●Antistatic tape
●Antistatic smocks, aprons, and sleeve protectors
●Conductive bins and other assembly or soldering aids
●Nonconductive foam
●Conductive slateop workstations with ground cords of one megohm resistance
●Static-dissipative tables or floor mats with hard ties to the ground
●Field service kits
●Static awareness labels
●Material-handling packages
●Nonconductive plastic bags, tubes, or boxes
●Metal tote boxes
●Electrostatic voltage levels and protective materials
The following table lists the shielding protection provided by antistatic bags and floor mats.
Material Use Voltage protection level
Antistatic plastics Bags 1,500 V
Carbon-loaded plastic Floor mats 7,500 V
Metallized laminate Floor mats 5,000 V
Grounding guidelines 33
5 Removal and replacement procedures –
slate
NOTE: This chapter provides removal and replacement procedures for Authorized Service Provider only
components. Components described in this chapter should only be accessed by an authorized service
provider. Accessing these components can damage the slate or void the warranty.
There are as many as 45 screws that must be removed, replaced, and/or loosened when servicing the slate.
Make special note of each screw size and location during removal and replacement.
NOTE: HP continually improves and changes product parts. For complete and current information on
supported parts for your slate, go to http://partsurfer.hp.com, select your country or region, and then follow
the on-screen instructions.
Unlocking the device and disabling Always On Remote
Management (select HP devices only)
HP Touchpoint Manager (HPTM) is a complete cloud-based solution for managing devices. For select HP
devices with the Windows operating system, the Always On Remote Management (AORM) feature is
automatically activated when HP Touchpoint Manager software is installed.
AORM can perform a secure BIOS level lock and can also securely erase internal drives (except for encrypted
self-encrypting drives). The HP Touchpoint Manager website (http://www.hptouchpointmanager.com)
provides access to the AORM lock feature. The device must be unlocked using an authorized PIN from
the same website before you can access HP Slate Setup and start the Windows operating system.
IMPORTANT: A service agent cannot retrieve the PIN from the HP Touchpoint Manager website. If a locked
device is returned for service, the agent must contact the customer to obtain the PIN to unlock the device. If a
PIN is not available, the entire system board must be replaced.
Before returning the device for service, be sure to unlock the device using the PIN from the HP Touchpoint
Manager website (http://www.hptouchpointmanager.com), and also disable the AORM feature in HP Slate
Setup.
To disable AORM:
1. Access HP Slate Setup (F10).
a. Turn on or restart the device, and then press esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
b. Press f10 to enter Slate Setup.
NOTE: If the BIOS is protected with an Administrator password, enter the password.
2. Select Advanced, and then select HP Touchpoint Manager Options.
3. Clear the Allow Activation check box.
4. Select Save changes and exit.
34 Chapter 5 Removal and replacement procedures – slate
Display panel assembly
Description Spare part number
11.6-in, TouchScreen, FHD, BV, (1920×1080), IPS, 50% CG, typical brightness 400 nits, eDP 1.3, ultra-
slim with digitizer display panel assembly
793736-001
11.6-in, TouchScreen, FHD, BV, (1920×1080), IPS, 50% CG, typical brightness 400 nits, eDP 1.3, ultra-
slim without digitizer display panel assembly
804352-001
11.6-in, TouchScreen, HD, BV, (1366×768), IPS, 50% CG, typical brightness 400 nits, eDP 1.2, ultra-slim
with digitizer display panel assembly
793737-001
11.6-in, TouchScreen, HD, BV, (1366×768), IPS, 50% CG, typical brightness 400 nits, eDP 1.2, ultra-slim
without digitizer display panel assembly
804351-001
Back cover 793725-001
Before removing the disassembling the slate, follow these steps:
1. Turn off the slate. If you are unsure whether the slate is off or in Hibernation, turn the slate on, and then
shut it down through the operating system.
2. Disconnect the power from the slate by unplugging the power cord from the slate.
3. Disconnect all external devices from the slate.
Remove the display panel assembly:
1. Place the slate on a flat work surface with the docking connector toward you.
2. Remove the speaker grille (1) that covers the display panel screws.
The speaker grille is available using spare part number 793734-001.
3. Remove the six Phillips PM1.5×8.3 screws (2) and the three Phillips PM1.5×3.5 screws (3) that secure
the display panel assembly to the bottom cover.
CAUTION: Do not completely separate the display panel assembly from the bottom cover in the next
step. There are 2 ribbon cables connecting the display panel assembly to the system board that can be
damaged if too much separation is achieved.
Display panel assembly 35
4. Lift the bottom edge (4) of the display panel assembly until it separates from the bottom cover.
5. Release the zero insertion force (ZIF) connector (1) to which the TouchScreen board cable is attached,
and then disconnect the TouchScreen board cable from the system board.
6. Release the adhesive strip (2) that secures the display panel cable connector to the system board.
7. Disconnect the display panel cable (3) from the system board.
8. Release the ZIF connector (4) to which the digitizer board cable is attached, and then disconnect
the digitizer board cable from the system board.
36 Chapter 5 Removal and replacement procedures – slate
9. Remove the display panel assembly (5).
CAUTION: Before turning the display panel upside down, make sure the work surface is clear of tools,
screws, and any other foreign objects. Failure to follow this caution can result in damage to
the display panel assembly.
10. If it is necessary to replace the display panel cable:
a. Turn the display panel assembly upside down with the docking connector toward you.
b. Release the adhesive strip (1) that secures the display panel cable connector to
the display panel assembly.
c. Disconnect the display panel cable (2) from the display panel.
Display panel assembly 37
d. Remove the display panel cable (3).
The display panel cable is available using spare part number 804344-001.
Reverse this procedure to reassemble and install the display panel assembly.
38 Chapter 5 Removal and replacement procedures – slate
Battery
Description Spare part number
Battery, 2-cell, 33-WHr, 4.56-AHr, Li-ion (includes cable) 750549-005
Before removing the battery, follow these steps:
1. Shut down the slate. If you are unsure whether the slate is off or in Hibernation, turn the slate on, and
then shut it down through the operating system.
2. Disconnect all external devices connected to the slate.
3. Disconnect the power from the slate by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the slate.
4. Remove the display panel assembly (see Display panel assembly on page 35).
WARNING! To reduce potential safety issues, use only the battery provided with the slate, a replacement
battery provided by HP, or a compatible battery purchased from HP.
CAUTION: Removing a battery that is the sole power source for the slate can cause loss of information.
To prevent loss of information, save your work or shut down the slate through Windows before removing
the battery.
Remove the battery:
1. Disconnect the battery cable (1) from the system board.
2. Remove the six PM1.6×2.5 screws (2) that secure the battery to the bottom cover.
3. Remove the battery (3).
Battery 39
Reverse this procedure to install the battery.
WLAN module
Description Spare part number
Intel 7265.NGWGQ.I 2 ac 2×2 + Bluetooth 4.0 LE PCIe+USB NGFF 2230 Combo Adapter 783721-005
Intel Tri Band Wireless-AC 17265 802.11a/b/g/n/ac 2×2 and Bluetooth 4.0 + WiGig Combo Adapter 806724-005
Intel Dual Band Wireless-AC 7265 802.11a/b/g/n/ac 2×2 WiFi and Bluetooth 4.0 Combo Adapter 756749-005
Intel Dual Band Wireless-AN 7265 802.11a/b/g/n 2×2 and Bluetooth 4.0 Combo Adapter 756748-005
CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless module
authorized for use in the slate by the governmental agency that regulates wireless devices in your country or
region. If you replace the module and then receive a warning message, remove the module to restore device
functionality, and then contact technical support.
Before removing the WLAN module, follow these steps:
1. Shut down the slate. If you are unsure whether the slate is off or in Hibernation, turn the slate on, and
then shut it down through the operating system.
2. Disconnect all external devices connected to the slate.
3. Disconnect the power from the slate by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the slate.
4. Remove the display panel assembly (see Display panel assembly on page 35).
5. Disconnect the battery cable from the system board (see Battery on page 39).
Remove the WLAN module:
1. Disconnect the WLAN antenna cables (1) from the terminals on the WLAN module.
NOTE: The WLAN antenna cable labeled “1/Main” connects to the WLAN module “1/Main” terminal.
The WLAN antenna cable labeled “2/Aux” connects to the WLAN module “2/Aux” terminal.
2. Remove the Phillips PM1.9×3.4 screw (2) that secures the WLAN module to the bottom cover. (The
WLAN module tilts up.)
40 Chapter 5 Removal and replacement procedures – slate
3. Remove the WLAN module (3) by pulling the module away from the slot at an angle.
NOTE: If the WLAN antenna cables are not connected to the WLAN module terminals, protective sleeves
should be installed on the antenna connectors, as shown in the following illustration.
Reverse this procedure to install the WLAN module.
WLAN module 41
WWAN module
Description Spare part number
HP lt4226 LTE/HSPA+ 4G Module 736675-005
HP lt4225 LTE/EV-DO 4G Module 793736-005
HP lt4211 LTE/EV-DO/HSPA+ 4G Module 793116-005
HP lt4112 LTE/HSPA+ 4G Module 790198-005
HP hs3110 HSPA+ Mobile Broadband Module 793516-005
CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless module
authorized for use in the slate by the governmental agency that regulates wireless devices in your country or
region. If you replace the module and then receive a warning message, remove the module to restore device
functionality, and then contact technical support.
Before removing the WWAN module, follow these steps:
1. Shut down the slate. If you are unsure whether the slate is off or in Hibernation, turn the slate on, and
then shut it down through the operating system.
2. Disconnect all external devices connected to the slate.
3. Disconnect the power from the slate by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the slate.
4. Remove the display panel assembly (see Display panel assembly on page 35).
5. Disconnect the battery cable from the system board (see Battery on page 39).
Remove the WWAN module:
1. Disconnect the WWAN antenna cables (1) from the terminals on the WWAN module.
NOTE: The WWAN antenna cable labeled “5/Main” connects to the WWAN module “5/Main” terminal.
The WWAN antenna cable labeled “6/Aux” connects to the WWAN module “6/Aux” terminal.
2. Remove the Phillips PM1.9×3.4 screw (2) that secures the WWAN module to the bottom cover. (The
WWAN module tilts up.)
42 Chapter 5 Removal and replacement procedures – slate
3. Remove the WWAN module (3) by pulling the module away from the slot at an angle.
NOTE: If the WWAN antenna cables are not connected to the WWAN module terminals, protective sleeves
should be installed on the antenna connectors, as shown in the following illustration.
Reverse this procedure to install the WWAN module.
WWAN module 43
Speakers
Description Spare part number
Speakers (include left and right speakers and cables) 793729-001
Before removing the speakers, follow these steps:
1. Shut down the slate. If you are unsure whether the slate is off or in Hibernation, turn the slate on, and
then shut it down through the operating system.
2. Disconnect all external devices connected to the slate.
3. Disconnect the power from the slate by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the slate.
4. Remove the display panel assembly (see Display panel assembly on page 35).
5. Remove the battery (see Battery on page 39).
Remove the speakers:
1. Disconnect the speaker cable (1) from the docking connector board.
2. Remove the four Phillips PM1.6×2.5 screws (2) that secure the speakers to the bottom cover.
3. Release the speakers cables from the retention tabs (3) built into the bottom cover.
4. Remove the speakers (4).
Reverse this procedure to install the speakers.
44 Chapter 5 Removal and replacement procedures – slate
Vibrator module
Description Spare part number
Vibrator module (includes left and right vibrator modules and cables) 793730-001
Before removing the vibrator module, follow these steps:
1. Shut down the slate. If you are unsure whether the slate is off or in Hibernation, turn the slate on, and
then shut it down through the operating system.
2. Disconnect all external devices connected to the slate.
3. Disconnect the power from the slate by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the slate.
4. Remove the display panel assembly (see Display panel assembly on page 35).
5. Remove the battery (see Battery on page 39).
Remove the vibrator module:
1. Disconnect the vibrator module cable (1) from the docking connector board.
2. Release the vibrator module cables from the retention tabs (2) built into the bottom cover.
3. Detach the vibrator module (3) from the bottom cover. (The vibrator module is attached to the bottom
cover with double-sided adhesive.)
4. Remove the vibrator module.
Reverse this procedure to install the vibrator module.
Vibrator module 45
Fan
Description Spare part number
Fan (includes cable) 793735-001
NOTE: To properly ventilate the slate, allow at least 7.6 cm (3 in) of clearance on the left side of the slate.
The slate uses an electric fan for ventilation. The fan is controlled by a temperature sensor and is designed to
turn on automatically when high temperature conditions exist. These conditions are affected by high external
temperatures, system power consumption, power management/battery conservation configurations,
battery fast charging, and software requirements. Exhaust air is displaced through the ventilation grill
located on the left side of the slate.
Before removing the fan, follow these steps:
1. Shut down the slate. If you are unsure whether the slate is off or in Hibernation, turn the slate on, and
then shut it down through the operating system.
2. Disconnect all external devices connected to the slate.
3. Disconnect the power from the slate by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the slate.
4. Remove the display panel assembly (see Display panel assembly on page 35).
5. Remove the battery (see Battery on page 39).
Remove the fan:
1. Disconnect the fan cable (1) from the system board.
2. Remove the three Phillips PM1.9×3.4 screws (2) that secure the fan to the bottom cover.
46 Chapter 5 Removal and replacement procedures – slate
3. Remove the fan (3).
Reverse this procedure to install the fan.
Volume button board
Description Spare part number
Volume button board
NOTE: The volume button board spare part kit does not include the volume button board cable. The
volume button board cable is included in the Slate Cable Kit, spare part number 793721-001.
793733-001
Before removing the volume button board, follow these steps:
1. Shut down the slate. If you are unsure whether the slate is off or in Hibernation, turn the slate on, and
then shut it down through the operating system.
2. Disconnect all external devices connected to the slate.
3. Disconnect the power from the slate by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the slate.
4. Remove the display panel assembly (see Display panel assembly on page 35).
5. Remove the battery (see Battery on page 39).
Remove the volume button board:
Volume button board 47
1. Release the ZIF connector (1) to which the volume button board cable is attached, and then disconnect
the volume button board cable from the system board.
2. Remove the three Phillips PM1.5×2.3 screws (2) that secure the volume button board to
the bottom cover.
3. Remove the bracket (3) that secures the volume button board to the bottom cover.
The volume button board bracket is included in the Slate Bracket Kit, spare part number 793712-001.
4. Remove the volume button board (4) and cable.
Reverse this procedure to install the volume button board.
48 Chapter 5 Removal and replacement procedures – slate
Docking connector board
Description Spare part number
Docking connector board
NOTE: The docking connector board spare part kit does not include the docking connector
board cable. The docking connector board cable is included in the Slate Cable Kit, spare part number
793721-001.
793731-001
Before removing the docking connector board, follow these steps:
1. Turn off the slate. If you are unsure whether the slate is off or in Hibernation, turn the slate on, and then
shut it down through the operating system.
2. Disconnect the power from the slate by unplugging the power cord from the slate.
3. Disconnect all external devices from the slate.
4. Remove the display panel assembly (see Display panel assembly on page 35).
5. Remove the battery (see Battery on page 39).
Remove the docking connector board:
1. Remove the following screws:
(1) Four Phillips PM1.9×2.5 screws
(2) One Phillips PM1.5×2.3 screw
(3) One Phillips PM1.5×3.5 screw
2. Remove the left alignment post connector bracket (4).
3. Remove the docking connector board bracket (5).
Docking connector board 49
4. Remove the right alignment post connector bracket (6).
The alignment post connector brackets and the docking connector board bracket are included in
the Table Bracket Kit, spare part number 793712-001.
5. Release the docking connector board (1) and audio jack board by sliding them back until they clear
the bottom edge of the bottom cover.
6. Flip the docking connector board (2) and audio jack board upside down.
50 Chapter 5 Removal and replacement procedures – slate
7. Release the ZIF connector (3) to which the docking connector board cable is attached, and then
disconnect the docking connector board cable from the docking connector board.
8. Remove the docking connector board, audio jack board, and audio jack board cable.
Reverse this procedure to install the docking connector board.
Audio jack board
Description Spare part number
Audio jack board (includes cable) 793732-001
Before removing the audio jack board, follow these steps:
1. Turn off the slate. If you are unsure whether the slate is off or in Hibernation, turn the slate on, and then
shut it down through the operating system.
2. Disconnect the power from the slate by unplugging the power cord from the slate.
3. Disconnect all external devices from the slate.
4. Remove the display panel assembly (see Display panel assembly on page 35).
5. Remove the battery (see Battery on page 39).
6. Remove the docking connector board (see Docking connector board on page 49).
Remove the audio jack board:
1. Release the ZIF connector (1) to which the audio jack board cable is attached, and then disconnect
the audio jack board cable from the docking connector board.
Audio jack board 51
2. Remove the audio jack board (2) and cable.
Reverse this procedure to install the audio jack board and cable.
System board
Description Spare part number
Equipped with an Intel Core i7 M-5Y71 processor, 8.0-GB of system memory, and the Windows 10 or
Windows 8 Professional operating system
805071-601
Equipped with an Intel Core i7 M-5Y71 processor, 8.0-GB of system memory, and the Windows 10 or
Windows 8 Standard operating system
805071-501
Equipped with an Intel Core i7 M-5Y71 processor, 8.0-GB of system memory, and a non-Windows
operating system
805071-001
Equipped with an Intel Core i7 M-5Y71 processor, 4.0-GB of system memory, and the Windows 10 or
Windows 8 Professional operating system
805072-601
Equipped with an Intel Core i7 M-5Y71 processor, 4.0-GB of system memory, and the Windows 10 or
Windows 8 Standard operating system
805072-501
Equipped with an Intel Core i7 M-5Y71 processor, 4.0-GB of system memory, and a non-
Windows operating system
805072-001
Equipped with an Intel Core i5 M-5Y51 processor, 8.0-GB of system memory, and the Windows 10 or
Windows 8 Professional operating system
805070-601
Equipped with an Intel Core i5 M-5Y51 processor, 8.0-GB of system memory, and the Windows 10 or
Windows 8 Standard operating system
805070-501
Equipped with an Intel Core i5 M-5Y51 processor, 8.0-GB of system memory, and a non-
Windows operating system
805070-001
Equipped with an Intel Core i5 M-5Y51 processor, 4.0-GB of system memory, and the Windows 10 or
Windows 8 Professional operating system
805069-601
Equipped with an Intel Core i5 M-5Y51 processor, 4.0-GB of system memory, and the Windows 10 or
Windows 8 Standard operating system
805069-501
Equipped with an Intel Core i5 M-5Y51 processor, 4.0-GB of system memory, and a non-Windows
operating system
805069-001
52 Chapter 5 Removal and replacement procedures – slate
Description Spare part number
Equipped with an Intel Core i3 M-5Y10c processor, 4.0-GB of system memory, and the Windows 10 or
Windows 8 Professional operating system
805068-601
Equipped with an Intel Core i3 M-5Y10c processor, 4.0-GB of system memory, and the Windows 10 or
Windows 8 Standard operating system
805068-501
Equipped with an Intel Core i3 M-5Y10c processor, 4.0-GB of system memory, and a non-
Windows operating system
805068-001
Before removing the system board, follow these steps:
1. Shut down the slate. If you are unsure whether the slate is off or in Hibernation, turn the slate on, and
then shut it down through the operating system.
2. Disconnect all external devices connected to the slate.
3. Disconnect the power from the slate by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the slate.
4. Remove the display panel assembly (see Display panel assembly on page 35), and then remove
the following components:
a. Battery (see Battery on page 39)
b. WLAN module (see WLAN module on page 40)
c. WWAN module (see WWAN module on page 42)
d. Fan (see Fan on page 46)
When replacing the system board, be sure that the following components are removed from the defective
system board and installed on the replacement system board:
●RTC battery (see RTC battery on page 59)
●Solid-state drive (see Solid-state drive on page 60)
●Heat sink (see Heat sink on page 62)
●Rear-facing webcam (see Rear-facing webcam on page 64)
●Front-facing webcam (see Front-facing webcam on page 65)
Remove the system board:
1. Detach the WLAN antenna transceiver (1) from the bottom cover. (The WLAN antenna transceiver is
attached to the bottom cover with double-sided adhesive.)
2. Remove the Phillips PM1.5×2.3 screw (2) that secures the front-facing webcam to the bottom cover.
3. Release the front-facing webcam (3) from the bottom cover.
System board 53
4. Detach the rear-facing webcam (4) from the bottom cover. (The rear-facing webcam is attached to
the bottom cover with double-sided adhesive.)
5. Release the ZIF connector (1) to which the volume button board cable is attached, and then disconnect
the volume button board cable from the volume button board.
6. Detach the RTC battery (2) from the bottom cover. (The RTC battery is attached to the bottom cover
with double-sided adhesive.)
7. Release the RTC battery cable from the retention clips (3) built into the bottom cover.
54 Chapter 5 Removal and replacement procedures – slate
8. Release the adhesive strip (4) that secures the docking connector board cable to the system board.
System board 55
9. Remove the six Phillips PM1.5×2.3 screws that secure the system board to the bottom cover.
10. Flip the system board (1) up and forward so that it rests upside down in the bottom cover.
11. Release the ZIF connector (2) to which the docking connector board cable is attached, and then
disconnect the docking connector board cable from the system board.
12. Remove the system board (3).
NOTE: When removing the system board, it is possible for the power button actuator to accidentally fall out
of the bottom cover. To install the power button actuator, follow the ensuing procedure:
1. Toe the power button actuator into the bottom cover, making sure the tabs fit under the ridge built into
the right side of the bottom cover.
56 Chapter 5 Removal and replacement procedures – slate
2. When the system board has been installed, make sure the power switch (1) engages with the notch (2)
built into the power button actuator.
Reverse this procedure to install the system board.
System board 57
Volume button board cable
NOTE: The volume button board cable is included in the Slate Cable Kit, spare part number 793721-001.
Before removing the volume button board cable, follow these steps:
1. Shut down the slate. If you are unsure whether the slate is off or in Hibernation, turn the slate on, and
then shut it down through the operating system.
2. Disconnect all external devices connected to the slate.
3. Disconnect the power from the slate by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the slate.
4. Remove the display panel assembly (see Display panel assembly on page 35), and then remove
the following components:
a. Battery (see Battery on page 39)
b. WLAN module (see WLAN module on page 40)
c. WWAN module (see WWAN module on page 42)
d. Fan (see Fan on page 46)
e. System board (see System board on page 52)
Remove the volume button board cable:
1. Turn the system board upside down with the docking connector toward you.
2. Release the ZIF connector (1) to which the volume button board cable is attached, and then disconnect
the volume button board cable from the system board.
3. Remove the volume button board cable (2).
Reverse this procedure to install the volume button board cable.
58 Chapter 5 Removal and replacement procedures – slate
RTC battery
Description Spare part number
RTC battery (includes cable and double-sided adhesive) 793723-001
Before removing the RTC battery, follow these steps:
1. Shut down the slate. If you are unsure whether the slate is off or in Hibernation, turn the slate on, and
then shut it down through the operating system.
2. Disconnect all external devices connected to the slate.
3. Disconnect the power from the slate by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the slate.
4. Remove the display panel assembly (see Display panel assembly on page 35), and then remove
the following components:
a. Battery (see Battery on page 39)
b. WLAN module (see WLAN module on page 40)
c. WWAN module (see WWAN module on page 42)
d. Fan (see Fan on page 46)
e. System board (see System board on page 52)
Remove the RTC battery:
1. Turn the system board upside down with the docking connector toward you.
2. Disconnect the RTC battery cable (1) from the system board.
3. Remove RTC battery (2).
RTC battery 59
Reverse this procedure to install the RTC battery.
Solid-state drive
Description Spare part number
512-GB, M2, SATA-3 solid-state drive 811391-001
256-GB, M2, SATA-3 793709-001
256-GB, M2, SATA-3 solid-state drive supporting TLC 811393-001
256-GB, M2, SATA-3, SED solid-state drive supporting Opal 2 810987-001
256-GB, M2, SanDisk X110 locked solid-state drive 824109-001
180-GB, M2, SATA-3 811389-001
180-GB, M2, SATA-3, SED solid-state drive supporting Opal 2 811390-001
128-GB, M2, SATA-3 793708-001
128-GB, M2, SATA-3 solid-state drive supporting TLC 811392-001
Before removing the solid-state drive, follow these steps:
1. Shut down the slate. If you are unsure whether the slate is off or in Hibernation, turn the slate on, and
then shut it down through the operating system.
2. Disconnect all external devices connected to the slate.
3. Disconnect the power from the slate by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the slate.
4. Remove the display panel assembly (see Display panel assembly on page 35), and then remove
the following components:
a. Battery (see Battery on page 39)
b. WLAN module (see WLAN module on page 40)
c. WWAN module (see WWAN module on page 42)
d. Fan (see Fan on page 46)
e. System board (see System board on page 52)
Remove the solid-state drive:
1. Turn the system board upside down with the docking connector toward you.
2. Remove the Phillips PM1.3×1.9 screw that secures the solid-state drive to the system board. (The solid-
state drive tilts up.)
60 Chapter 5 Removal and replacement procedures – slate
3. Remove solid-state drive (2).
Reverse this procedure to install the solid-state drive.
Solid-state drive 61
Heat sink
Description Spare part number
Heat sink (includes replacement thermal material) 793726-001
Before removing the heat sink, follow these steps:
1. Shut down the slate. If you are unsure whether the slate is off or in Hibernation, turn the slate on, and
then shut it down through the operating system.
2. Disconnect all external devices connected to the slate.
3. Disconnect the power from the slate by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the slate.
4. Remove the display panel assembly (see Display panel assembly on page 35), and then remove
the following components:
a. Battery (see Battery on page 39)
b. WLAN module (see WLAN module on page 40)
c. WWAN module (see WWAN module on page 42)
d. Fan (see Fan on page 46)
e. System board (see System board on page 52)
Remove the heat sink:
1. Turn the system board upside down with the docking connector toward you.
2. Remove the four Phillips PM1.9×3.4 screws (1) that secure the heat sink to the system board.
NOTE: Due to the adhesive quality of the thermal material located between the heat sink and system
board components, it may be necessary to move the heat sink from side to side to detach it.
62 Chapter 5 Removal and replacement procedures – slate
3. Remove the heat sink (2).
NOTE: The thermal material must be thoroughly cleaned from the surfaces of the heat sink and the system
board each time the heat sink is removed. Thermal paste is used on the processor (1) and the heat sink
section (2) that services it.
Reverse this procedure to install the heat sink.
Heat sink 63
Rear-facing webcam
NOTE: The rear-facing webcam is included in the Webcam Kit, spare part number 793724-001.
The rear-facing webcam spare part kit does not include the rear-facing webcam cable. The rear-facing
webcam cable is included in the Slate Cable Kit, spare part number 793721-001.
Before removing the rear-facing webcam, follow these steps:
1. Shut down the slate. If you are unsure whether the slate is off or in Hibernation, turn the slate on, and
then shut it down through the operating system.
2. Disconnect all external devices connected to the slate.
3. Disconnect the power from the slate by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the slate.
4. Remove the display panel assembly (see Display panel assembly on page 35), and then remove
the following components:
a. Battery (see Battery on page 39)
b. WLAN module (see WLAN module on page 40)
c. WWAN module (see WWAN module on page 42)
d. Fan (see Fan on page 46)
e. System board (see System board on page 52)
Remove the rear-facing webcam:
1. Turn the system board upside down with the top edge toward you.
2. Disconnect the rear-facing webcam cable (1) from the front-facing webcam board.
3. Remove the rear-facing webcam (2).
Reverse this procedure to install the rear-facing webcam.
64 Chapter 5 Removal and replacement procedures – slate
Front-facing webcam
NOTE: The front-facing webcam is included in the Webcam Kit, spare part number 793724-001, and
includes double-sided adhesive.
The front-facing webcam spare part kit does not include the front-facing webcam cable. The front-facing
webcam cable is included in the Slate Cable Kit, spare part number 793721-001.
Before removing the front-facing webcam, follow these steps:
1. Shut down the slate. If you are unsure whether the slate is off or in Hibernation, turn the slate on, and
then shut it down through the operating system.
2. Disconnect all external devices connected to the slate.
3. Disconnect the power from the slate by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the slate.
4. Remove the display panel assembly (see Display panel assembly on page 35), and then remove
the following components:
a. Battery (see Battery on page 39)
b. WLAN module (see WLAN module on page 40)
c. WWAN module (see WWAN module on page 42)
d. Fan (see Fan on page 46)
e. System board (see System board on page 52)
f. Rear-facing webcam (see Rear-facing webcam on page 64)
Remove the front-facing webcam:
1. Release the ZIF connector (1) to which the front-facing webcam board cable is attached, and then
disconnect the front-facing webcam board cable from the system board.
2. Detach the front-facing webcam board cable (2) from the system board. (The front-facing webcam
board cable is attached to the system board with double-sided adhesive.)
Front-facing webcam 65
3. Remove the front-facing webcam (3) and cable.
Reverse this procedure to install the front-facing webcam.
66 Chapter 5 Removal and replacement procedures – slate
WWAN antenna
NOTE: The WWAN auxiliary and main antennas are included in the Antenna Kit, using the following spare
part numbers:
●805065-001 – For use in African, European, and Middle Eastern countries and regions
●806251-001 – For use in Japan
●805067-001 – For use in North America
Before removing the WWAN antenna, follow these steps:
1. Shut down the slate. If you are unsure whether the slate is off or in Hibernation, turn the slate on, and
then shut it down through the operating system.
2. Disconnect all external devices connected to the slate.
3. Disconnect the power from the slate by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the slate.
4. Remove the display panel assembly (see Display panel assembly on page 35), and then remove
the following components:
a. Battery (see Battery on page 39)
b. WLAN module (see WLAN module on page 40)
c. WWAN module (see WWAN module on page 42)
d. Fan (see Fan on page 46)
e. System board (see System board on page 52)
Remove the WWAN antenna:
1. Detach the WWAN main antenna transceiver (1) from the bottom cover. (The WWAN main antenna
transceiver is attached to the bottom cover with double-sided adhesive.)
WWAN antenna 67
2. Release the WWAN main antenna (2) transceiver and cable.
3. Detach the WWAN auxiliary antenna transceiver (1) from the bottom cover. (The WWAN auxiliary
antenna transceiver is attached to the bottom cover with double-sided adhesive.)
4. Release the WWAN auxiliary antenna cable from the retention tabs (2) built into the bottom cover.
68 Chapter 5 Removal and replacement procedures – slate
5. Release the WWAN auxiliary antenna (3) transceiver and cable.
Reverse this procedure to install the WWAN antenna.
WWAN antenna 69
WLAN antenna
NOTE: The WLAN main antenna is included in the Antenna Kit, using the following spare part numbers:
●805065-001 – For use in African, European, and Middle Eastern countries and regions
●806251-001 – For use in Japan
●805067-001 – For use in North America
Before removing the WLAN antenna, follow these steps:
1. Shut down the slate. If you are unsure whether the slate is off or in Hibernation, turn the slate on, and
then shut it down through the operating system.
2. Disconnect all external devices connected to the slate.
3. Disconnect the power from the slate by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the slate.
4. Remove the display panel assembly (see Display panel assembly on page 35), and then remove
the following components:
a. Battery (see Battery on page 39)
b. WLAN module (see WLAN module on page 40)
c. WWAN module (see WWAN module on page 42)
d. Fan (see Fan on page 46)
e. System board (see System board on page 52)
Remove the WLAN antenna:
1. Release the WLAN antenna cable from the retention tabs (1) built into the bottom cover.
2. Remove the WLAN antenna (2) transceiver and cable.
70 Chapter 5 Removal and replacement procedures – slate
Reverse this procedure to install the WLAN antenna.
WiGig antenna
Description Spare part number
WiGig antenna (includes WiGig antenna cable and transceiver) 805066-001
Before removing the WiGig antenna, follow these steps:
1. Shut down the slate. If you are unsure whether the slate is off or in Hibernation, turn the slate on, and
then shut it down through the operating system.
2. Disconnect all external devices connected to the slate.
3. Disconnect the power from the slate by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the slate.
4. Remove the display panel assembly (see Display panel assembly on page 35), and then remove
the following components:
a. Battery (see Battery on page 39)
b. WLAN module (see WLAN module on page 40)
c. WWAN module (see WWAN module on page 42)
d. Fan (see Fan on page 46)
e. System board (see System board on page 52)
Remove the WiGig antenna:
1. Detach the WiGig antenna transceiver (1) from the bottom cover. (The WiGig antenna transceiver is
attached to the bottom cover with double-sided adhesive.)
2. Release the WiGig antenna cable from the retention tabs (2) built into the bottom cover.
WiGig antenna 71
3. Remove the WiGig antenna (3) cable and transceiver.
Reverse this procedure to install the WiGig antenna.
Docking connector board cable
NOTE: The docking connector board cable is included in the Slate Cable Kit, spare part number 793721-001.
Before removing the docking connector board cable, follow these steps:
1. Shut down the slate. If you are unsure whether the slate is off or in Hibernation, turn the slate on, and
then shut it down through the operating system.
2. Disconnect all external devices connected to the slate.
3. Disconnect the power from the slate by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the slate.
4. Remove the display panel assembly (see Display panel assembly on page 35), and then remove
the following components:
a. Battery (see Battery on page 39)
b. WLAN module (see WLAN module on page 40)
c. WWAN module (see WWAN module on page 42)
d. Fan (see Fan on page 46)
e. Docking connector board (see Docking connector board on page 49)
f. System board (see System board on page 52)
Remove the docking connector board cable:
1. Detach the docking connector board cable (1) from the bottom cover. (The docking connector
board cable is attached to the bottom cover with double-sided adhesive.)
72 Chapter 5 Removal and replacement procedures – slate
2. Remove the docking connector board cable (2).
Reverse this procedure to install the docking connector board cable.
Docking connector board cable 73
6 Removal and replacement procedures –
Keyboard base
NOTE: This chapter provides removal and replacement procedures for Authorized Service Provider only
components. Components described in this chapter should only be accessed by an authorized service
provider. Accessing these components can damage the keyboard base or void the warranty.
There are as many as 49 screws that must be removed, replaced, and/or loosened when servicing
the keyboard base. Make special note of each screw size and location during removal and replacement.
NOTE: HP continually improves and changes product parts. For complete and current information on
supported parts for your keyboard base, go to http://partsurfer.hp.com, select your country or region, and
then follow the on-screen instructions.
Bottom cover
Description Spare part number
Bottom cover 793710-001
Rubber Kit (includes bottom cover rubber feet) 804348-001
Before disassembling the keyboard base, follow these steps:
1. Turn off the keyboard base. If you are unsure whether the keyboard base is off or in Hibernation, turn
the keyboard base on, and then shut it down through the operating system.
2. Disconnect the power from the keyboard base by unplugging the power cord from the keyboard base.
3. Disconnect all external devices from the keyboard base.
Remove the bottom cover:
1. Turn the keyboard base upside down on a flat work surface with the front edge toward you.
2. Remove the eleven Torx8 T8M2.0×4.3 screws (1) secure the bottom cover to the keyboard base.
74 Chapter 6 Removal and replacement procedures – Keyboard base
3. Remove the bottom cover (2).
Reverse this procedure to install the bottom cover.
Keyboard base battery
Description Spare part number
Battery, 6-cell, 21-WHr, 0.95-AHr, LI (includes cable) 750550-005
Before removing the keyboard base battery, follow these steps:
1. Shut down the keyboard base. If you are unsure whether the keyboard base is off or in Hibernation, turn
the keyboard base on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the keyboard base.
3. Disconnect the power from the keyboard base by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the keyboard base.
4. Remove the bottom cover (see Bottom cover on page 74).
Remove the keyboard base battery:
1. Disconnect the keyboard base battery cable (1) from the keyboard base system board.
2. Remove the nine PM2.0×3.6 screws (2) that secure the keyboard base battery to the keyboard base.
Keyboard base battery 75
3. Remove the keyboard base battery (3).
Reverse this procedure to install the keyboard base battery.
Power connector cable
Description Spare part number
Power connector cable 793714-001
Before removing the power connector cable, follow these steps:
1. Shut down the keyboard base. If you are unsure whether the keyboard base is off or in Hibernation, turn
the keyboard base on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the keyboard base.
3. Disconnect the power from the keyboard base by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the keyboard base.
4. Remove the bottom cover (see Bottom cover on page 74).
5. Disconnect the keyboard base battery cable from the keyboard base system board (see Keyboard base
battery on page 75).
Remove the power connector cable:
76 Chapter 6 Removal and replacement procedures – Keyboard base
1. Disconnect the power connector cable (1) from the keyboard base system board.
2. Remove the two Phillips PM2.0×3.6 screws (2) that secure the power connector cable bracket to
the top cover.
3. Remove the power connector cable bracket (3).
The power connector cable bracket is included in the Keyboard Base Bracket Kit, spare part number
793728-001.
4. Remove the Phillips PM1.5×2.7 screw (4) that secures the power connector to the top cover.
5. Remove the power connector cable (5).
Reverse this procedure to install the power connector cable.
Keyboard
For use in country or region: Spare part number: For use in country or region: Spare part number:
Keyboard (includes keyboard cable and keyboard
backlight cable):
For use in the Netherlands 793738-B31
For use in Belgium 793738-A41 For use in Northwest Africa 793738-FP1
For use in Brazil 793738-201 For use in Norway 793738-091
For use in Bulgaria 793738-261 For use in Portugal 793738-131
For use in Canada 793738-DB1 For use in Romania 793738-271
For use in the Czech Republic
and Slovakia
793738-FL1 For use in Russia 793738-251
For use in Denmark 793738-081 For use in Saudi Arabia 793738-171
Keyboard 77
For use in country or region: Spare part number: For use in country or region: Spare part number:
For use in France 793738-051 For use in Slovenia 793738-BA1
For use in Germany 793738-041 For use in South Korea 793738-AD1
For use in Greece 793738-151 For use in Spain 793738-071
For use in Hungary 793738-211 For use in Sweden and Finland 793738-B71
For use in Iceland 793738-DD1 For use in Switzerland 793738-111
For use in India 793738-D61 For use in Taiwan 793738-AB1
For use in Israel 793738-BB1 For use in Thailand 793738-281
For use in Italy 793738-061 For use in Turkey 793738-141
For use in Japan 793738-291 For use in the United Kingdom
and Singapore
793738-031
For use in Latin America 793738-161 For use in the United States 793738-001
Before removing the keyboard, follow these steps:
1. Shut down the keyboard base. If you are unsure whether the keyboard base is off or in Hibernation, turn
the keyboard base on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the keyboard base.
3. Disconnect the power from the keyboard base by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the keyboard base.
4. Remove the bottom cover (see Bottom cover on page 74).
5. Remove the keyboard base battery (see Keyboard base battery on page 75).
Remove the keyboard:
1. Disconnect the keyboard backlight cable from the low insertion force (LIF) connector (1) on keyboard
base system board.
2. Release the ZIF connector (2) to which the keyboard cable is attached, and then disconnect
the keyboard cable from the keyboard base system board.
3. Release the six retention tabs (3) that secure the keyboard to the top cover.
78 Chapter 6 Removal and replacement procedures – Keyboard base
4. Insert a case utility tool (4) or similar thin, plastic tool into the keyboard release hole and press on
the back of the keyboard.
NOTE: When releasing the keyboard, make sure the keyboard backlight cable (5) and the keyboard
cable (6) route cleanly through the openings in the top cover.
5. Turn the keyboard base right side up with the front edge toward you.
6. Lift the rear edge of the keyboard (1) until it rests at an angle.
7. Slide the keyboard (2) up and back at an angle until the tabs on the front edge disengage from the slots
built into the top cover.
8. Remove the keyboard (3).
Reverse this procedure to install the keyboard.
Keyboard 79
Fingerprint reader board
Description Spare part number
Fingerprint reader board
NOTE: The fingerprint reader board spare part kit does not include the fingerprint reader board cable.
The fingerprint reader board cable is included in the Keyboard Base Cable Kit, spare part number
793721-001.
793713-001
Before removing the fingerprint reader board, follow these steps:
1. Shut down the keyboard base. If you are unsure whether the keyboard base is off or in Hibernation, turn
the keyboard base on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the keyboard base.
3. Disconnect the power from the keyboard base by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the keyboard base.
4. Remove the bottom cover (see Bottom cover on page 74).
5. Remove the keyboard base battery (see Keyboard base battery on page 75).
Remove the fingerprint reader board:
1. Disconnect the fingerprint reader board cable from the LIF connector (1) on fingerprint reader board.
2. Remove the Phillips PM1.5×2.7 screw (2) that secures the fingerprint reader board and bracket to
the top cover.
3. Remove the fingerprint reader board bracket (3).
The fingerprint reader board bracket is included in the Keyboard Base Bracket Kit, spare part number
793728-001.
80 Chapter 6 Removal and replacement procedures – Keyboard base
4. Remove the fingerprint reader board (4).
Reverse this procedure to install the fingerprint reader board.
TouchPad
Description Spare part number
TouchPad (includes cable) 793720-001
Before removing the TouchPad, follow these steps:
1. Shut down the keyboard base. If you are unsure whether the keyboard base is off or in Hibernation, turn
the keyboard base on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the keyboard base.
3. Disconnect the power from the keyboard base by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the keyboard base.
4. Remove the bottom cover (see Bottom cover on page 74).
5. Remove the keyboard base battery (see Keyboard base battery on page 75).
Remove the TouchPad:
1. Disconnect the TouchPad cable from the LIF connector (1) on smart card reader board.
2. Remove the four Phillips PM1.5×2.7 screws (2) that secure the TouchPad to the top cover.
TouchPad 81
3. Remove the TouchPad (3).
Reverse this procedure to install the TouchPad.
Smart card reader board
Description Spare part number
Smart card reader board
NOTE: The smart card reader board spare part kit does not include the smart card reader board cable.
The smart card reader board cable is included in the Keyboard Base Cable Kit, spare part number
793721-001.
793711-001
Before removing the smart card reader board, follow these steps:
1. Shut down the keyboard base. If you are unsure whether the keyboard base is off or in Hibernation, turn
the keyboard base on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the keyboard base.
3. Disconnect the power from the keyboard base by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the keyboard base.
4. Remove the bottom cover (see Bottom cover on page 74).
5. Remove the battery (see Keyboard base battery on page 75).
Remove the smart card reader board:
1. Disconnect the TouchPad cable from the LIF connector (1) on smart card reader board.
2. Release the ZIF connector (2) to which the smart card reader board cable is attached, and then
disconnect the smart card reader board cable from the keyboard base connector board.
82 Chapter 6 Removal and replacement procedures – Keyboard base
3. Remove the five Phillips PM1.5×2.7 screws (3) that secure the smart card reader board to the top cover.
4. Remove the smart card reader board (4).
Reverse this procedure to install the smart card reader board.
Connector board
Description Spare part number
Connector board (includes USB port and DisplayPort)
NOTE: The connector board spare part kit does not include the connector board cable. The
connector board cable is included in the Keyboard Base Cable Kit, spare part number 793721-001.
804350-001
Before removing the connector board, follow these steps:
1. Shut down the keyboard base. If you are unsure whether the keyboard base is off or in Hibernation, turn
the keyboard base on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the keyboard base.
3. Disconnect the power from the keyboard base by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the keyboard base.
4. Remove the bottom cover (see Bottom cover on page 74).
5. Remove the keyboard base battery (see Keyboard base battery on page 75).
Remove the connector board:
Connector board 83
1. Release the ZIF connector (1) to which the smart card reader board cable is attached, and then
disconnect the smart card reader board cable from the keyboard base connector board.
2. Release the ZIF connector (2) to which the connector board cable is attached, and then disconnect
the connector board cable from the keyboard base system board.
3. Remove the two Phillips PM2.0×3.6 screws (3) that secure the connector board and bracket to
the top cover.
4. Remove the connector board bracket (4).
The connector board bracket is included in the Keyboard Base Bracket Kit, spare part number
793728-001.
5. Remove the connector board (5) and cable.
Reverse this procedure to install the connector board.
Keyboard base system board
Description Spare part number
Keyboard base system board (includes docking/adapter port, USB port, and audio jack) 806252-001
Before removing the keyboard base system board, follow these steps:
1. Shut down the keyboard base. If you are unsure whether the keyboard base is off or in Hibernation, turn
the keyboard base on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the keyboard base.
3. Disconnect the power from the keyboard base by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the keyboard base.
84 Chapter 6 Removal and replacement procedures – Keyboard base
4. Remove the bottom cover (see Bottom cover on page 74).
5. Remove the keyboard base battery (see Keyboard base battery on page 75).
Remove the keyboard base system board:
1. Disconnect the fingerprint reader board cable from the LIF connector (1) on fingerprint reader board.
2. Detach the fingerprint reader board cable (2) from the top cover. (The fingerprint reader board cable is
attached to the top cover with double-sided adhesive.)
3. Release the adhesive strip (3) that secures the hinge assembly right cable to the keyboard base
system board.
4. Disconnect the hinge assembly right cable (4) from the keyboard base system board.
5. Disconnect the power connector cable (5) from the keyboard base system board.
6. Disconnect the keyboard backlight cable from the LIF connector (1) on the keyboard base system board.
7. Release the ZIF connector (2) to which the keyboard cable is attached, and then disconnect
the keyboard cable from the keyboard base system board.
8. Release the adhesive strip (3) that secures the hinge assembly left cable to the keyboard base
system board.
9. Disconnect the hinge assembly left cable (4) from the keyboard base system board.
Keyboard base system board 85
10. Release the ZIF connector (5) to which the connector board cable is attached, and then disconnect
the connector board cable from the keyboard base system board.
11. Remove the two Phillips PM2.0×2.5 broad head screws (1) that secure the keyboard base system board
to the top cover.
12. Remove the two Phillips PM2.0×3.6 screws (2) that secure the power connector cable bracket to
the top cover.
13. Remove the power connector cable bracket (3).
The power connector cable bracket is included in the Keyboard Base Bracket Kit, spare part number
793728-001.
14. Lift the right side of the keyboard base system board (4) until it rests at an angle.
86 Chapter 6 Removal and replacement procedures – Keyboard base
15. Remove the keyboard base system board (5) by sliding it up and to the right at an angle.
Reverse this procedure to install the keyboard base system board.
Fingerprint reader board cable
NOTE: The fingerprint reader board cable is included in the Keyboard Base Cable Kit, spare part number
793721-001.
Before removing the fingerprint reader board cable, follow these steps:
1. Shut down the keyboard base. If you are unsure whether the keyboard base is off or in Hibernation, turn
the keyboard base on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the keyboard base.
3. Disconnect the power from the keyboard base by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the keyboard base.
4. Remove the bottom cover (see Bottom cover on page 74).
5. Remove the keyboard base battery (see Keyboard base battery on page 75).
6. Remove the keyboard system board (see Keyboard base system board on page 84).
Remove the fingerprint reader board cable:
1. Turn the keyboard base system board upside down with the front toward you.
2. Release the ZIF connector (1) to which the fingerprint reader board cable is attached, and then
disconnect the fingerprint reader board cable from the keyboard base system board.
Fingerprint reader board cable 87
3. Remove the fingerprint reader board cable (2).
The fingerprint reader board cable is included in the Keyboard Base Cable Kit, spare part number
793721-001.
Reverse this procedure to install the fingerprint reader board cable.
Kickstand
Description Spare part number
Kickstand (includes rubber feet) 793715-001
Kickstand Hinge Kit 793716-001
Before removing the kickstand, follow these steps:
1. Shut down the keyboard base. If you are unsure whether the keyboard base is off or in Hibernation, turn
the keyboard base on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the keyboard base.
3. Disconnect the power from the keyboard base by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the keyboard base.
4. Remove the bottom cover (see Bottom cover on page 74).
5. Disconnect the keyboard base battery cable from the keyboard base system board (see Keyboard base
battery on page 75).
Remove the kickstand:
1. Remove the four Phillips PM2.0×2.5 broad head screws (1) that secure the kickstand to the top cover.
88 Chapter 6 Removal and replacement procedures – Keyboard base
2. Remove the kickstand (2).
Reverse this procedure to install the kickstand.
Hinge assembly
Description Spare part number
Hinge assembly (includes left and right cables) 793717-001
Before removing the hinge assembly, follow these steps:
1. Shut down the keyboard base. If you are unsure whether the keyboard base is off or in Hibernation, turn
the keyboard base on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the keyboard base.
3. Disconnect the power from the keyboard base by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the keyboard base.
4. Remove the bottom cover (see Bottom cover on page 74).
5. Disconnect the keyboard base battery cable from the keyboard base system board (see Keyboard base
battery on page 75).
6. Remove the kickstand (see Kickstand on page 88).
Remove the hinge assembly:
1. Release the adhesive strips (1) that secure the hinge assembly cables to the keyboard base
system board.
2. Disconnect the hinge assembly cables (2) from the keyboard base system board.
3. Remove the four Torx8 T8M2.0×3.2 screws (3) that secure the hinge assembly to the top cover.
Hinge assembly 89
4. Remove the two Phillips PM2.0×2.5 broad head screws (4) that secure the hinge assembly to
the top cover.
5. Remove the hinge assembly (5).
Reverse this procedure to install the hinge assembly.
90 Chapter 6 Removal and replacement procedures – Keyboard base
7 Computer Setup (BIOS), TPM, and
HP Sure Start – Windows 10
Using Computer Setup
Computer Setup, or Basic Input/Output System (BIOS), controls communication between all the input and
output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Computer Setup
includes settings for the types of devices installed, the startup sequence of the computer, and the amount of
system and extended memory.
NOTE: Use extreme care when making changes in Computer Setup. Errors can prevent the computer from
operating properly.
Starting Computer Setup
NOTE: An external keyboard or mouse connected to a USB port can be used with Computer Setup only if
USB legacy support is enabled.
To start Computer Setup, follow these steps:
▲Start Computer Setup.
●Computers or tablets with keyboards:
▲ Turn on or restart the computer, and when the HP logo appears, press f10 to enter
Computer Setup.
●Tablets without keyboards:
▲ Turn off the tablet. Press the power button in combination with the volume down button until
the Startup menu is displayed, and then tap F10 to enter Computer Setup.
Using Computer Setup 91
Navigating and selecting in Computer Setup
●To select a menu or a menu item, use the tab key and the keyboard arrow keys and then press enter, or
use a pointing device to select the item.
NOTE: On tablets without keyboards, you can use your finger to make selections.
●To scroll up and down, select the up arrow or the down arrow in the upper-right corner of the screen, or
use the up arrow key or the down arrow key on the keyboard.
●To close open dialog boxes and return to the main Computer Setup screen, press esc, and then follow
the on-screen instructions.
To exit Computer Setup menus, choose one of the following methods:
●To exit Computer Setup menus without saving your changes:
Select the Exit icon in the lower-right corner of the screen, and then follow the on-screen instructions.
‒ or –
Select Main, select Ignore Changes and Exit, and then press enter.
●To save your changes and exit Computer Setup menus:
Select the Save icon in the lower-right corner of the screen, and then follow the on-screen instructions.
‒ or –
Select Main, select Save Changes and Exit, and then press enter.
Your changes go into effect when the computer restarts.
Restoring factory settings in Computer Setup
NOTE: Restoring defaults will not change the hard drive mode.
To return all settings in Computer Setup to the values that were set at the factory, follow these steps:
1. Start Computer Setup. See Starting Computer Setup on page 91.
2. Select Main, and then select Apply Factory Defaults and Exit.
NOTE: On select products, the selections may display Restore Defaults instead of Apply Factory
Defaults and Exit.
3. Follow the on-screen instructions.
4. To save your changes and exit, select the Save icon in the lower-right corner of the screen, and then
follow the on-screen instructions.
‒ or –
Select Main, select Save Changes and Exit, and then press enter.
Your changes go into effect when the computer restarts.
NOTE: Your password settings and security settings are not changed when you restore the factory settings.
92 Chapter 7 Computer Setup (BIOS), TPM, and HP Sure Start – Windows 10
Updating the BIOS
Updated versions of the BIOS may be available on the HP website.
Most BIOS updates on the HP website are packaged in compressed files called SoftPaqs.
Some download packages contain a file named Readme.txt, which contains information regarding installing
and troubleshooting the file.
Determining the BIOS
To decide whether you need to update Computer Setup (BIOS), first determine the BIOS version on
your computer.
BIOS version information (also known as ROM date and System BIOS) can be accessed by pressing fn+esc (if
you are already in Windows) or by using Computer Setup.
1. Start Computer Setup. See Starting Computer Setup on page 91.
2. Select Main, and then select System Information.
3. To exit Computer Setup without saving your changes, select the Exit icon in the lower-right corner of
the screen, and then follow the on-screen instructions.
‒ or –
Select Main, select Ignore Changes and Exit, and then press enter.
To check for later BIOS versions, see Downloading a BIOS update on page 93.
Downloading a BIOS update
CAUTION: To reduce the risk of damage to the computer or an unsuccessful installation, download and
install a BIOS update only when the computer is connected to reliable external power using the AC adapter.
Do not download or install a BIOS update while the computer is running on battery power, docked in an
optional docking device, or connected to an optional power source. During the download and installation,
follow these instructions:
Do not disconnect power on the computer by unplugging the power cord from the AC outlet.
Do not shut down the computer or initiate Sleep.
Do not insert, remove, connect, or disconnect any device, cable, or cord.
1. Type support in the taskbar search box, and then select the HP Support Assistant app.
‒ or –
Select the question mark icon in the taskbar.
2. Select Updates, and then select Check for updates and messages.
3. Follow the on-screen instructions.
4. At the download area, follow these steps:
a. Identify the most recent BIOS update and compare it to the BIOS version currently installed on
your computer. Make a note of the date, name, or other identifier. You may need this information
to locate the update later, after it has been downloaded to your hard drive.
b. Follow the on-screen instructions to download your selection to the hard drive.
Make a note of the path to the location on your hard drive where the BIOS update is downloaded.
You will need to access this path when you are ready to install the update.
Using Computer Setup 93
NOTE: If you connect your computer to a network, consult the network administrator before
installing any software updates, especially system BIOS updates.
BIOS installation procedures vary. Follow any instructions that are revealed on the screen after the download
is complete. If no instructions are revealed, follow these steps:
1. Type file in the taskbar search box, and then select File Explorer.
2. Select your hard drive designation. The hard drive designation is typically Local Disk (C:).
3. Using the hard drive path you recorded earlier, open the folder that contains the update.
4. Double-click the file that has an .exe extension (for example, filename.exe).
The BIOS installation begins.
5. Complete the installation by following the on-screen instructions.
NOTE: After a message on the screen reports a successful installation, you can delete the downloaded file
from your hard drive.
Changing the boot order using the f9 prompt
To dynamically choose a boot device for the current startup sequence, follow these steps:
1. Access the Boot Device Options menu:
●Computers or tablets with keyboards:
▲ Turn on or restart the computer, and when the HP logo appears, press f9 to enter the Boot
Device Options menu.
●Tablets without keyboards:
▲ Turn off the tablet. Press the power button in combination with the volume down button until
the Startup menu is displayed, and then tap F9 to enter the Boot Device Options menu.
2. Select a boot device, then press enter.
94 Chapter 7 Computer Setup (BIOS), TPM, and HP Sure Start – Windows 10
TPM BIOS settings (select products only)
IMPORTANT: Before enabling Trusted Platform Module (TPM) functionality on this system, you must
ensure that your intended use of TPM complies with relevant local laws, regulations and policies, and
approvals or licenses must be obtained if applicable. For any compliance issues arising from your operation/
usage of TPM which violates the above mentioned requirement, you shall bear all the liabilities wholly and
solely. HP will not be responsible for any related liabilities.
TPM provides additional security for your computer. You can modify the TPM settings in Computer Setup
(BIOS).
NOTE: If you change the TPM setting to Hidden, TPM is not visible in the operating system.
To access TPM settings in Computer Setup:
1. Start Computer Setup. See Starting Computer Setup on page 91.
2. Select Security, select TPM Embedded Security, and then follow the on-screen instructions.
Using HP Sure Start (select products only)
Select computer models are configured with HP Sure Start, a technology that continuously monitors
the computer's BIOS for attacks or corruption. If the BIOS becomes corrupted or is attacked, HP Sure Start
automatically restores the BIOS to its previously safe state, without user intervention.
HP Sure Start is configured and already enabled so that most users can use the HP Sure Start default
configuration. The default configuration can be customized by advanced users.
To access the latest documentation on HP Sure Start, go to http://www.hp.com/support, and select
your country. Select Drivers & Downloads, and then follow the on-screen instructions.
TPM BIOS settings (select products only) 95
8 HP PC Hardware Diagnostics (UEFI) –
Windows 10
HP PC Hardware Diagnostics is a Unified Extensible Firmware Interface (UEFI) that allows you to run
diagnostic tests to determine whether the computer hardware is functioning properly. The tool runs outside
the operating system so that it can isolate hardware failures from issues that are caused by the operating
system or other software components.
NOTE: To start BIOS on a convertible computer, your computer must be in notebook mode and you must
use the keyboard attached to your tablet. The on-screen keyboard, which displays in tablet mode, cannot
access BIOS.
To start HP PC Hardware Diagnostics UEFI:
1. Start BIOS:
●Computers or tablets with keyboards:
▲ Turn on or restart the computer, quickly press esc.
●Tablets without keyboards:
▲ Turn on or restart the tablet, and then quickly hold down the volume down button.
‒ or –
Turn on or restart the tablet, and then quickly hold down the Windows button.
2. Press or tap f2.
The BIOS searches three places for the diagnostic tools, in the following order:
a. Connected USB drive
NOTE: To download the HP PC Hardware Diagnostics (UEFI) tool to a USB drive, see Downloading
HP PC Hardware Diagnostics (UEFI) to a USB device on page 97.
b. Hard drive
c. BIOS
3. When the diagnostic tool opens, select the type of diagnostic test you want to run, and then follow
the on-screen instructions. On a tablet, press the volume down button to stop a diagnostic test.
NOTE: If you need to stop a diagnostic test on computers or tablets with a keyboard, press esc.
96 Chapter 8 HP PC Hardware Diagnostics (UEFI) – Windows 10
Downloading HP PC Hardware Diagnostics (UEFI) to a USB device
There are two options to download HP PC Hardware Diagnostics to a USB device:
Download the latest UEFI version:
1. Go to http://www.hp.com/go/techcenter/pcdiags. The HP PC Diagnostics home page is displayed.
2. In the HP PC Hardware Diagnostics section, click the Download link, and then select Run.
Download any version of UEFI for a specific product:
1. Go to http://www.hp.com/support, and then select your country. The HP Support page is displayed.
2. Click Drivers & Downloads.
3. In the text box, enter the product name, and then click Go.
– or –
Click Find Now to let HP automatically detect your product.
4. Select your computer, and then select your operating system.
5. In the Diagnostic section, follow the on-screen instructions to select and download the UEFI version
you want.
Downloading HP PC Hardware Diagnostics (UEFI) to a USB device 97
9 Computer Setup (BIOS), MultiBoot, and
HP PC Hardware Diagnostics (UEFI) –
Windows 8
Using Computer Setup
Computer Setup, or Basic Input/Output System (BIOS), controls communication between all the input and
output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Computer Setup
includes settings for the types of devices installed, the startup sequence of the computer, and the amount of
system and extended memory.
NOTE: Use extreme care when making changes in Computer Setup. Errors can prevent the computer from
operating properly.
Starting Computer Setup
NOTE: An external keyboard or mouse connected to a USB port can be used with Computer Setup only if
USB legacy support is enabled.
To start Computer Setup, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
2. Press f10 to enter Computer Setup.
Navigating and selecting in Computer Setup
To navigate and select in Computer Setup, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
NOTE: You can use either a pointing device (TouchPad, pointing stick, or USB mouse) or the keyboard
to navigate and make selections in Computer Setup.
2. Press f10 to enter Computer Setup.
●To select a menu or a menu item, use the tab key and the keyboard arrow keys and then press
enter, or use a pointing device to click the item.
●To scroll up and down, click the up arrow or the down arrow in the upper-right corner of
the screen, or use the up arrow key or the down arrow key on the keyboard.
●To close open dialog boxes and return to the main Computer Setup screen, press esc, and then
follow the on-screen instructions.
To exit Computer Setup menus, choose one of the following methods:
●To exit Computer Setup menus without saving your changes:
Click the Exit icon in the lower-right corner of the screen, and then follow the on-screen instructions.
98 Chapter 9 Computer Setup (BIOS), MultiBoot, and HP PC Hardware Diagnostics (UEFI) – Windows 8
– or –
Use the arrow keys to select Main > Ignore Changes and Exit, and then press enter.
●To save your changes and exit Computer Setup menus:
Click the Save icon in the lower-right corner of the screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select Main > Save Changes and Exit, and then press enter.
Your changes go into effect when the computer restarts.
Restoring factory settings in Computer Setup
NOTE: Restoring defaults will not change the hard drive mode.
To return all settings in Computer Setup to the values that were set at the factory, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
2. Press f10 to enter Computer Setup.
3. Use a pointing device or the arrow keys to select Main > Restore Defaults.
4. Follow the on-screen instructions.
5. To save your changes and exit, click the Save icon in the lower-right corner of the screen, and then
follow the on-screen instructions.
– or –
Use the arrow keys to select Main > Save Changes and Exit, and then press enter.
Your changes go into effect when the computer restarts.
NOTE: Your password settings and security settings are not changed when you restore the factory settings.
Using Computer Setup 99
Updating the BIOS
Updated versions of the BIOS may be available on the HP website.
Most BIOS updates on the HP website are packaged in compressed files called SoftPaqs.
Some download packages contain a file named Readme.txt, which contains information regarding installing
and troubleshooting the file.
Determining the BIOS version
To determine whether available BIOS updates contain later BIOS versions than those currently installed on
the computer, you need to know the version of the system BIOS currently installed.
BIOS version information (also known as ROM date and System BIOS) can be revealed by pressing fn+esc (if
you are already in Windows) or by using Computer Setup.
1. Start Computer Setup.
2. Use a pointing device or the arrow keys to select Main > System Information.
3. To exit Computer Setup without saving your changes, click the Exit icon in the lower-right corner of
the screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select Main > Ignore Changes and Exit, and then press enter.
Downloading a BIOS update
CAUTION: To reduce the risk of damage to the computer or an unsuccessful installation, download and
install a BIOS update only when the computer is connected to reliable external power using the AC adapter.
Do not download or install a BIOS update while the computer is running on battery power, docked in an
optional docking device, or connected to an optional power source. During the download and installation,
follow these instructions:
Do not disconnect power on the computer by unplugging the power cord from the AC outlet.
Do not shut down the computer or initiate Sleep.
Do not insert, remove, connect, or disconnect any device, cable, or cord.
1. From the Start screen, type support, and then select the HP Support Assistant app.
2. Click Updates and tune-ups, and then click Check for HP updates now.
3. Follow the on-screen instructions.
4. At the download area, follow these steps:
a. Identify the most recent BIOS update and compare it to the BIOS version currently installed on
your computer. Make a note of the date, name, or other identifier. You may need this information
to locate the update later, after it has been downloaded to your hard drive.
b. Follow the on-screen instructions to download your selection to the hard drive.
If the update is more recent than your BIOS, make a note of the path to the location on your hard
drive where the BIOS update is downloaded. You will need to access this path when you are ready
to install the update.
NOTE: If you connect your computer to a network, consult the network administrator before installing
any software updates, especially system BIOS updates.
100 Chapter 9 Computer Setup (BIOS), MultiBoot, and HP PC Hardware Diagnostics (UEFI) – Windows 8
BIOS installation procedures vary. Follow any instructions that are revealed on the screen after the download
is complete. If no instructions are revealed, follow these steps:
1. From the Start screen, type file, and then select File Explorer.
2. Click your hard drive designation. The hard drive designation is typically Local Disk (C:).
3. Using the hard drive path you recorded earlier, open the folder on your hard drive that contains
the update.
4. Double-click the file that has an .exe extension (for example, filename.exe).
The BIOS installation begins.
5. Complete the installation by following the on-screen instructions.
NOTE: After a message on the screen reports a successful installation, you can delete the downloaded file
from your hard drive.
Using MultiBoot
About the boot device order
As the computer starts, the system attempts to boot from enabled devices. The MultiBoot utility, which is
enabled at the factory, controls the order in which the system selects a boot device. Boot devices can include
optical drives, diskette drives, a network interface card (NIC), hard drives, and USB devices. Boot devices
contain bootable media or files that the computer needs to start and operate properly.
NOTE: Some boot devices must be enabled in Computer Setup before they can be included in the boot
order.
You can change the order in which the computer searches for a boot device by changing the boot order in
Computer Setup. You can also press esc while the “Press the ESC key for Startup Menu” message is displayed
at the bottom of the screen, and then press f9. Pressing f9 displays a menu that shows the current boot
devices and allows you to select a boot device. Or, you can use MultiBoot Express to set the computer to
prompt you for a boot location each time the computer turns on or restarts.
Choosing MultiBoot preferences
You can use MultiBoot in the following ways:
●To set a new boot order that the computer uses each time it is turned on, by changing the boot order in
Computer Setup.
●To dynamically choose the boot device, by pressing esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen, and then pressing f9 to enter the Boot Device Options
menu.
●To use MultiBoot Express to set variable boot orders. This feature prompts you for a boot device each
time the computer is turned on or restarted.
Setting a new boot order in Computer Setup
To start Computer Setup and set a boot device order that the computer uses each time it is turned on or
restarted, follow these steps:
Using MultiBoot 101
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
2. Press f10 to enter Computer Setup.
3. Use a pointing device or the arrow keys to select one of the following options:
●Advanced > Boot Options > UEFI Boot Order > UEFI Hybrid
●Advanced > Boot Options > UEFI Boot Order > UEFI Native Boot mode
●Advanced > Boot Options > Legacy Boot Order > Legacy Boot Mode
Press enter.
4. To move the device up in the boot order, use a pointing device to click the up arrow, or press the + key.
– or –
To move the device down in the boot order, use a pointing device to click the down arrow, or press the -
key.
5. To save your changes and exit Computer Setup, click the Save icon in the lower-left corner of
the screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select Main > Save Changes and Exit, and then press enter.
Dynamically choosing a boot device using the f9 prompt
To dynamically choose a boot device for the current startup sequence, follow these steps:
1. Open the Select Boot Device menu by turning on or restarting the computer, and then pressing esc while
the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen.
2. Press f9.
3. Use a pointing device or the arrow keys to select a boot device, then press enter.
Setting a MultiBoot Express prompt
To start Computer Setup and set the computer to display the MultiBoot startup location menu each time
the computer is started or restarted, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
2. Press f10 to enter Computer Setup.
3. Use a pointing device or the arrow keys to select Advanced > Boot Options > MultiBoot Express Boot
Popup Delay (Sec), and then press enter.
4. In the MultiBoot Express Popup Delay (Sec) field, enter the length of time in seconds that you want
the computer to display the startup location menu before it defaults to the current MultiBoot setting.
(When 0 is selected, the Express Boot startup location menu is not displayed.)
5. To save your changes and exit Computer Setup, click the Save icon in the lower-left corner of
the screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select Main > Save Changes and Exit, and then press enter.
102 Chapter 9 Computer Setup (BIOS), MultiBoot, and HP PC Hardware Diagnostics (UEFI) – Windows 8
Your changes go into effect when the computer restarts.
Entering MultiBoot Express preferences
When the Express Boot menu is displayed during startup, you have the following choices:
●To specify a boot device from the Express Boot menu, select your preference within the allotted time,
and then press enter.
●To prevent the computer from defaulting to the current MultiBoot setting, press any key before
the allotted time expires. The computer will not start until you select a boot device and press enter.
●To allow the computer to start according to the current MultiBoot settings, wait for the allotted time to
expire.
Using HP PC Hardware Diagnostics (UEFI)
HP PC Hardware Diagnostics is a Unified Extensible Firmware Interface (UEFI) that allows you to run
diagnostic tests to determine whether the computer hardware is functioning properly. The tool runs outside
the operating system so that it can isolate hardware failures from issues that are caused by the operating
system or other software components.
To start HP PC Hardware Diagnostics UEFI:
1. Turn on or restart the computer, quickly press esc, and then press f2.
The BIOS searches three places for the diagnostic tools, in the following order:
a. Connected USB drive
NOTE: To download the HP PC Hardware Diagnostics (UEFI) tool to a USB drive, see Downloading
HP PC Hardware Diagnostics (UEFI) to a USB device on page 103.
b. Hard drive
c. BIOS
2. When the diagnostic tool opens, use the keyboard arrow keys to select the type of diagnostic test you
want to run, and then follow the on-screen instructions.
NOTE: If you need to stop a diagnostic test, press esc.
Downloading HP PC Hardware Diagnostics (UEFI) to a USB device
NOTE: Instructions for downloading HP PC Hardware Diagnostics (UEFI) are provided in English only.
There are two options to download HP PC Hardware Diagnostics to a USB device:
Option 1: HP PC Diagnostics homepage— Provides access to the latest UEFI version
1. Go to http://hp.com/go/techcenter/pcdiags.
2. Click the UEFI Download link, and then select Run.
Option 2: Support and Drivers page—Provides downloads for a specific product for earlier and later
versions
1. Go to http://www.hp.com.
2. Point to Support, located at the top of the page, and then click Download Drivers.
Using HP PC Hardware Diagnostics (UEFI) 103
3. In the text box, enter the product name, and then click Go.
– or –
Click Find Now to let HP automatically detect your product.
4. Select your computer model, and then select your operating system.
5. In the Diagnostic section, click HP UEFI Support Environment.
– or –
Click Download, and then select Run.
Using HP Sure Start (select models only)
Select computer models are configured with HP Sure Start, a technology that continuously monitors
the computer's BIOS for attacks or corruption. If the BIOS becomes corrupted or is attacked, HP Sure Start
automatically restores the BIOS to its previously safe state, without user intervention.
HP Sure Start is configured and already enabled so that most users can use the HP Sure Start default
configuration. The default configuration can be customized by advanced users.
To access the latest documentation on HP Sure Start, go to http://www.hp.com/support, and select your
country. Select Drivers & Downloads, and then follow the on-screen instructions.
104 Chapter 9 Computer Setup (BIOS), MultiBoot, and HP PC Hardware Diagnostics (UEFI) – Windows 8
10 Computer Setup (BIOS), MultiBoot, and
HP PC Hardware Diagnostics (UEFI) –
Windows 7
Using Computer Setup
Computer Setup, or Basic Input/Output System (BIOS), controls communication between all the input and
output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Computer Setup
includes settings for the types of devices installed, the startup sequence of the computer, and the amount of
system and extended memory.
NOTE: Use extreme care when making changes in Computer Setup. Errors can prevent the computer from
operating properly.
Starting Computer Setup
NOTE: An external keyboard or mouse connected to a USB port can be used with Computer Setup only if
USB legacy support is enabled.
To start Computer Setup, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
2. Press f10 to enter Computer Setup.
Navigating and selecting in Computer Setup
To navigate and select in Computer Setup, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
NOTE: You can use either a pointing device (TouchPad, pointing stick, or USB mouse) or the keyboard
to navigate and make selections in Computer Setup.
2. Press f10 to enter Computer Setup.
●To select a menu or a menu item, use the tab key and the keyboard arrow keys and then press
enter, or use a pointing device to click the item.
●To scroll up and down, click the up arrow or the down arrow in the upper-right corner of
the screen, or use the up arrow key or the down arrow key on the keyboard.
●To close open dialog boxes and return to the main Computer Setup screen, press esc, and then
follow the on-screen instructions.
To exit Computer Setup menus, choose one of the following methods:
●To exit Computer Setup menus without saving your changes:
Click the Exit icon in the lower-right corner of the screen, and then follow the on-screen instructions.
Using Computer Setup 105
– or –
Use the arrow keys to select Main > Ignore Changes and Exit, and then press enter.
●To save your changes and exit Computer Setup menus:
Click the Save icon in the lower-right corner of the screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select Main > Save Changes and Exit, and then press enter.
Your changes go into effect when the computer restarts.
Restoring factory settings in Computer Setup
NOTE: Restoring defaults will not change the hard drive mode.
To return all settings in Computer Setup to the values that were set at the factory, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
2. Press f10 to enter Computer Setup.
3. Use a pointing device or the arrow keys to select Main > Restore Defaults.
4. Follow the on-screen instructions.
5. To save your changes and exit, click the Save icon in the lower-right corner of the screen, and then
follow the on-screen instructions.
– or –
Use the arrow keys to select Main > Save Changes and Exit, and then press enter.
Your changes go into effect when the computer restarts.
NOTE: Your password settings and security settings are not changed when you restore the factory settings.
106 Chapter 10 Computer Setup (BIOS), MultiBoot, and HP PC Hardware Diagnostics (UEFI) – Windows 7
Updating the BIOS
Updated versions of the BIOS may be available on the HP website.
Most BIOS updates on the HP website are packaged in compressed files called SoftPaqs.
Some download packages contain a file named Readme.txt, which contains information regarding installing
and troubleshooting the file.
Determining the BIOS version
To determine whether available BIOS updates contain later BIOS versions than those currently installed on
the computer, you need to know the version of the system BIOS currently installed.
BIOS version information (also known as ROM date and System BIOS) can be revealed by pressing fn+esc (if
you are already in Windows) or by using Computer Setup.
1. Start Computer Setup.
2. Use a pointing device or the arrow keys to select Main > System Information.
3. To exit Computer Setup without saving your changes, click the Exit icon in the lower-right corner of
the screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select Main > Ignore Changes and Exit, and then press enter.
Downloading a BIOS update
CAUTION: To reduce the risk of damage to the computer or an unsuccessful installation, download and
install a BIOS update only when the computer is connected to reliable external power using the AC adapter.
Do not download or install a BIOS update while the computer is running on battery power, docked in an
optional docking device, or connected to an optional power source. During the download and installation,
follow these instructions:
Do not disconnect power on the computer by unplugging the power cord from the AC outlet.
Do not shut down the computer or initiate Sleep.
Do not insert, remove, connect, or disconnect any device, cable, or cord.
1. Access Help and Support by selecting Start > Help and Support.
2. Select Updates and tune-ups, and then select Check for HP updates now.
3. At the download area, follow these steps:
a. Identify the most recent BIOS update and compare it to the BIOS version currently installed on
your computer. Make a note of the date, name, or other identifier. You may need this information
to locate the update later, after it has been downloaded to your hard drive.
b. Follow the on-screen instructions to download your selection to the hard drive.
If the update is more recent than your BIOS, make a note of the path to the location on your hard
drive where the BIOS update is downloaded. You will need to access this path when you are ready
to install the update.
NOTE: If you connect your computer to a network, consult the network administrator before installing
any software updates, especially system BIOS updates.
BIOS installation procedures vary. Follow any instructions that are revealed on the screen after the download
is complete. If no instructions are revealed, follow these steps:
Using Computer Setup 107
1. Select Start > Computer.
2. Click your hard drive designation. The hard drive designation is typically Local Disk (C:).
3. Using the hard drive path you recorded earlier, open the folder on your hard drive that contains
the update.
4. Double-click the file that has an .exe extension (for example, filename.exe).
The BIOS installation begins.
5. Complete the installation by following the on-screen instructions.
NOTE: After a message on the screen reports a successful installation, you can delete the downloaded file
from your hard drive.
Using MultiBoot
About the boot device order
As the computer starts, the system attempts to boot from enabled devices. The MultiBoot utility, which is
enabled at the factory, controls the order in which the system selects a boot device. Boot devices can include
optical drives, diskette drives, a network interface card (NIC), hard drives, and USB devices. Boot devices
contain bootable media or files that the computer needs to start and operate properly.
NOTE: Some boot devices must be enabled in Computer Setup before they can be included in the boot
order.
You can change the order in which the computer searches for a boot device by changing the boot order in
Computer Setup. You can also press esc while the “Press the ESC key for Startup Menu” message is displayed
at the bottom of the screen, and then press f9. Pressing f9 displays a menu that shows the current boot
devices and allows you to select a boot device. Or, you can use MultiBoot Express to set the computer to
prompt you for a boot location each time the computer turns on or restarts.
Choosing MultiBoot preferences
You can use MultiBoot in the following ways:
●To set a new boot order that the computer uses each time it is turned on, by changing the boot order in
Computer Setup.
●To dynamically choose the boot device, by pressing esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen, and then pressing f9 to enter the Boot Device Options
menu.
●To use MultiBoot Express to set variable boot orders. This feature prompts you for a boot device each
time the computer is turned on or restarted.
Setting a new boot order in Computer Setup
To start Computer Setup and set a boot device order that the computer uses each time it is turned on or
restarted, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
2. Press f10 to enter Computer Setup.
3. Use a pointing device or the arrow keys to select the Legacy Boot Order list, and then press enter.
108 Chapter 10 Computer Setup (BIOS), MultiBoot, and HP PC Hardware Diagnostics (UEFI) – Windows 7
4. To move the device up in the boot order, use a pointing device to click the up arrow, or press the + key.
– or –
To move the device down in the boot order, use a pointing device to click the down arrow, or press the -
key.
5. To save your changes and exit Computer Setup, click the Save icon in the lower-left corner of
the screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select Main > Save Changes and Exit, and then press enter.
Dynamically choosing a boot device using the f9 prompt
To dynamically choose a boot device for the current startup sequence, follow these steps:
1. Open the Select Boot Device menu by turning on or restarting the computer, and then pressing esc while
the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen.
2. Press f9.
3. Use a pointing device or the arrow keys to select a boot device, then press enter.
Setting a MultiBoot Express prompt
To start Computer Setup and set the computer to display the MultiBoot startup location menu each time
the computer is started or restarted, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
2. Press f10 to enter Computer Setup.
3. Use a pointing device or the arrow keys to select System Configuration > Boot Options, and then press
enter.
4. In the MultiBoot Express Popup Delay (Sec) field, enter the length of time in seconds that you want
the computer to display the startup location menu before it defaults to the current MultiBoot setting.
(When 0 is selected, the Express Boot startup location menu is not displayed.)
5. To save your changes and exit Computer Setup, click the Save icon in the lower-left corner of
the screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select Main > Save Changes and Exit, and then press enter.
Your changes go into effect when the computer restarts.
Entering MultiBoot Express preferences
When the Express Boot menu is displayed during startup, you have the following choices:
Using MultiBoot 109
●To specify a boot device from the Express Boot menu, select your preference within the allotted time,
and then press enter.
●To prevent the computer from defaulting to the current MultiBoot setting, press any key before
the allotted time expires. The computer will not start until you select a boot device and press enter.
●To allow the computer to start according to the current MultiBoot settings, wait for the allotted time to
expire.
Using HP PC Hardware Diagnostics (UEFI) (select models only)
HP PC Hardware Diagnostics is a Unified Extensible Firmware Interface (UEFI) that allows you to run
diagnostic tests to determine if the computer hardware is functioning properly. The tool runs outside of
the operating system to isolate hardware failures from issues that may be caused by the operating system or
other software components.
To start HP PC Hardware Diagnostics UEFI:
1. Turn on or restart the computer, quickly press esc, and then press f2.
After pressing f2, the BIOS searches three places for the HP PC Hardware Diagnostics (UEFI) tools in
the following order:
a. Connected USB drive
NOTE: To download the HP PC Hardware Diagnostics (UEFI) tool to a USB drive, see Downloading
HP PC Hardware Diagnostics (UEFI) to a USB device on page 110.
b. Hard drive
c. BIOS
2. Use the keyboard arrow keys to select the type of diagnostic test you want to run, and then follow
the on-screen instructions.
NOTE: If you need to stop a diagnostic test while it is running, press esc.
Downloading HP PC Hardware Diagnostics (UEFI) to a USB device
NOTE: The HP PC Hardware Diagnostics (UEFI) download instructions are provided in English only.
There are two options to download HP PC Hardware Diagnostics to a USB device:
Option 1: HP PC Diagnostics homepage— Provides access to the latest UEFI version
1. Go to http://hp.com/go/techcenter/pcdiags.
2. Click the UEFI Download link, and then select Run.
Option 2: Support and Drivers page—Provides downloads for a specific product for earlier and later
versions
1. Go to http://www.hp.com.
2. Point to Support, located at the top of the page, and then click Download Drivers.
3. In the text box, enter the product name, and then click Go.
– or –
Click Find Now to let HP automatically detect your product.
110 Chapter 10 Computer Setup (BIOS), MultiBoot, and HP PC Hardware Diagnostics (UEFI) – Windows 7
4. Select your computer model, and then select your operating system.
5. In the Diagnostic section, click HP UEFI Support Environment.
– or –
Click Download, and then select Run.
Using HP PC Hardware Diagnostics (UEFI) (select models only) 111
11 Specifications
Metric U.S.
Slate dimensions
Width 29.80 cm 11.73 in
Depth 19.27 cm 7.59 in
Height 1.07 cm 0.42 in
Weight 0.82 kg 1.80 lbs
System (slate and keyboard base) dimensions
Width 29.80 cm 11.73 in
Depth 20.42 cm 8.04 in
Height 2.08 cm 0.82 in
Weight 1.54 kg 3.40 lbs
Input power
Operating voltage and current 19.5 V dc @ 2.31 A – 45 W
19.5 V dc @ 3.33 A – 65 W
19.5 V dc @ 4.62 A – 90 W
19.5 V dc @ 10.25 A – Slim 200 W
19.5 V dc @ 11.79 A – Slim 230 W
NOTE: This product is designed for IT power systems in Norway with phase-to-phase voltage not exceeding 240V rms.
NOTE: The slate operating voltage and current can be found on the system regulatory label.
Temperature
Operating 5°C to 35°C 41°F to 95°F
Nonoperating ‑20°C to 60°C ‑4°F to 140°F
Relative humidity (noncondensing)
Operating 10% to 90%
Nonoperating 5% to 95%
Maximum altitude (unpressurized)
Operating ‑15 m to 3,048 m ‑50 ft to 10,000 ft
Nonoperating ‑15 m to 12,192 m ‑50 ft to 40,000 ft
NOTE: Applicable product safety standards specify thermal limits for plastic surfaces. The device operates well within this range of
temperatures.
112 Chapter 11 Specifications
12 Backup and recovery – Windows 10
This chapter provides information about the following processes. The information in the chapter is standard
procedure for most products.
●Creating recovery media and backups
●Restoring and recovering your system
For additional information, refer to the HP support assistant app.
▲Type support in the taskbar search box, and then select the HP Support Assistant app.
‒ or –
Click the question mark icon in the taskbar.
IMPORTANT: If you will be performing recovery procedures on a tablet, the tablet battery must be at least
70% charged before you start the recovery process.
IMPORTANT: For a tablet with a detachable keyboard, connect the keyboard to the keyboard dock before
beginning any recovery process.
Creating recovery media and backups
The following methods of creating recovery media and backups are available on select products only. Choose
the available method according to your computer model.
●Use HP Recovery Manager to create HP Recovery media after you successfully set up the computer. This
step creates a backup of the HP Recovery partition on the computer. The backup can be used to reinstall
the original operating system in cases where the hard drive is corrupted or has been replaced. For
information on creating recovery media, see Creating HP Recovery media (select products only)
on page 114. For information on the recovery options that are available using the recovery media, see
Using Windows Tools on page 115.
●Use Windows tools to create system restore points and create backups of personal information.
For more information, see Recovering using HP Recovery Manager on page 116.
NOTE: If storage is 32 GB or less, Microsoft System Restore is disabled by default.
Creating recovery media and backups 113
Creating HP Recovery media (select products only)
If possible, check for the presence of the Recovery partition and the Windows partition. From the Start menu,
select File Explorer, and then select This PC.
●If your computer does not list the Windows partition and the Recovery partition, you can obtain
recovery media for your system from support. See the Worldwide Telephone Numbers booklet included
with the computer. You can also find contact information on the HP website. Go to http://www.hp.com/
support, select your country or region, and follow the on-screen instructions.
You can use Windows tools to create system restore points and create backups of personal information,
see Using Windows tools on page 61.
●If your computer does list the Recovery partition and the Windows partition, you can use HP Recovery
Manager to create recovery media after you successfully set up the computer. HP Recovery media can
be used to perform system recovery if the hard drive becomes corrupted. System recovery reinstalls
the original operating system and software programs that were installed at the factory and then
configures the settings for the programs. HP Recovery media can also be used to customize the system
or restore the factory image if you replace the hard drive.
◦Only one set of recovery media can be created. Handle these recovery tools carefully, and keep
them in a safe place.
◦HP Recovery Manager examines the computer and determines the required storage capacity for
the media that will be required.
◦To create recovery discs, your computer must have an optical drive with DVD writer capability, and
you must use only high-quality blank DVD-R, DVD+R, DVD-R DL, or DVD+R DL discs. Do not use
rewritable discs such as CD±RW, DVD±RW, double-layer DVD±RW, or BD-RE (rewritable Blu-ray)
discs; they are not compatible with HP Recovery Manager software. Or, instead, you can use a
high-quality blank USB flash drive.
◦If your computer does not include an integrated optical drive with DVD writer capability, but you
would like to create DVD recovery media, you can use an external optical drive (purchased
separately) to create recovery discs. If you use an external optical drive, it must be connected
directly to a USB port on the computer; the drive cannot be connected to a USB port on an external
device, such as a USB hub. If you cannot create DVD media yourself, you can obtain recovery discs
for your computer from HP. See the Worldwide Telephone Numbers booklet included with
the computer. You can also find contact information on the HP website. Go to http://www.hp.com/
support, select your country or region, and follow the on-screen instructions.
◦Be sure that the computer is connected to AC power before you begin creating the recovery media.
◦The creation process can take an hour or more. Do not interrupt the creation process.
◦If necessary, you can exit the program before you have finished creating all of the recovery DVDs.
HP Recovery Manager will finish burning the current DVD. The next time you start HP Recovery
Manager, you will be prompted to continue.
To create HP Recovery media:
IMPORTANT: For a tablet with a detachable keyboard, connect the keyboard to the keyboard dock before
beginning these steps.
1. Type recovery in the taskbar search box, and then select HP Recovery Manager.
2. Select Create recovery media, and then follow the on-screen instructions.
If you ever need to recover the system, see Recovering using HP Recovery Manager on page 116.
114 Chapter 12 Backup and recovery – Windows 10
Using Windows Tools
You can create recovery media, system restore points, and backups of personal information using
Windows tools.
NOTE: If storage is 32 GB or less, Microsoft System Restore is disabled by default.
For more information and steps, see the Get started app.
▲Select the Start button, and then select the Get started app.
Restore and recovery
There are several options for recovering your system. Choose the method that best matches your situation
and level of expertise:
IMPORTANT: Not all methods are available on all products.
●Windows offers several options for restoring from backup, refreshing the computer, and resetting
the computer to its original state. For more information see the Get started app.
▲ Select the Start button, and then select the Get started app.
●If you need to correct a problem with a preinstalled application or driver, use the Reinstall drivers
and/or applications option (select products only) of HP Recovery Manager to reinstall the individual
application or driver.
▲ Type recovery in the taskbar search box, select HP Recovery Manager, select Reinstall drivers
and/or applications, and then follow the on-screen instructions.
●If you want to recover the Windows partition to original factory content, you can choose the System
Recovery option from the HP Recovery partition (select products only) or use the HP Recovery media.
For more information, see Recovering using Recovering using HP Recovery Manager on page 116. If you
have not already created recovery media, see Creating HP Recovery media (select products only)
on page 114.
●On select products, if you want to recover the computer's original factory partition and content, or if you
have replaced the hard drive, you can use the Factory Reset option of HP Recovery media. For more
information, see Recovering using HP Recovery Manager on page 116.
●On select products, if you want to remove the recovery partition to reclaim hard drive space,
HP Recovery Manager offers the Remove Recovery Partition option.
For more information, see Removing the Removing the HP Recovery partition (select products only)
on page 118.
Using Windows Tools 115
Recovering using HP Recovery Manager
HP Recovery Manager software allows you to recover the computer to its original factory state by using
the HP Recovery media that you either created or that you obtained from HP, or by using the HP Recovery
partition (select products only). If you have not already created recovery media, see Creating HP Recovery
media (select products only) on page 114.
What you need to know before you get started
●HP Recovery Manager recovers only software that was installed at the factory. For software not
provided with this computer, you must either download the software from the manufacturer's website
or reinstall the software from the media provided by the manufacturer.
IMPORTANT: Recovery through HP Recovery Manager should be used as a final attempt to correct
computer issues.
●To use the Factory Reset option (select products only), you must use HP Recovery media. If you have
not already created recovery media, see Creating HP Recovery media (select products only)
on page 114.
●If your computer does not allow the creation of HP Recovery media or if the HP Recovery media does
not work, you can obtain recovery media for your system from support. See the Worldwide Telephone
Numbers booklet included with the computer. You can also find contact information from
the HP website. Go to http://www.hp.com/support, select your country or region, and follow the on-
screen instructions.
IMPORTANT: HP Recovery Manager does not automatically provide backups of your personal data. Before
beginning recovery, back up any personal data you want to retain.
Using HP Recovery media, you can choose from one of the following recovery options:
NOTE: Only the options available for your computer display when you start the recovery process.
●System Recovery—Reinstalls the original operating system, and then configures the settings for
the programs that were installed at the factory.
●Factory Reset—Restores the computer to its original factory state by deleting all information from
the hard drive and re-creating the partitions. Then it reinstalls the operating system and the software
that was installed at the factory.
The HP Recovery partition (select products only) allows System Recovery only.
116 Chapter 12 Backup and recovery – Windows 10
Using the HP Recovery partition (select products only)
The HP Recovery partition allows you to perform a system recovery without the need for recovery discs or a
recovery USB flash drive. This type of recovery can be used only if the hard drive is still working.
To start HP Recovery Manager from the HP Recovery partition:
IMPORTANT: For a tablet with a detachable keyboard, connect the keyboard to the keyboard dock before
beginning these steps (select products only).
1. Type recovery in the taskbar search box, select Recovery Manager, and then select
HP Recovery Environment.
‒ or –
For computers or tablets with keyboards attached, press f11 while the computer boots, or press and
hold f11 as you press the power button.
For tablets without keyboards:
Turn on or restart the tablet, and then quickly hold down the volume down button; then select f11.
‒ or –
Turn on or restart the tablet, and then quickly hold down the Windows button; then select f11.
2. Select Troubleshoot from the boot options menu.
3. Select Recovery Manager, and then follow the on-screen instructions.
Using HP Recovery media to recover
You can use HP Recovery media to recover the original system. This method can be used if your system does
not have an HP Recovery partition or if the hard drive is not working properly.
1. If possible, back up all personal files.
2. Insert the HP Recovery media, and then restart the computer.
NOTE: If the computer does not automatically restart in HP Recovery Manager, change the computer
boot order. See Changing the computer boot order on page 118.
3. Follow the on-screen instructions.
Restore and recovery 117
Changing the computer boot order
If your computer does not restart in HP Recovery Manager, you can change the computer boot order, which is
the order of devices listed in BIOS where the computer looks for startup information. You can change
the selection to an optical drive or a USB flash drive.
To change the boot order:
IMPORTANT: For a tablet with a detachable keyboard, connect the keyboard to the keyboard dock before
beginning these steps.
1. Insert the HP Recovery media.
2. Access BIOS:
For computers or tablets with keyboards attached:
▲Turn on or restart the computer or tablet, quickly press esc, and then press f9 for boot options.
For tablets without keyboards:
▲Turn on or restart the tablet, and then quickly hold down the volume down button; then select f9.
‒ or –
Turn on or restart the tablet, and then quickly hold down the Windows button; then select f9.
3. Select the optical drive or USB flash drive from which you want to boot.
4. Follow the on-screen instructions.
Removing the HP Recovery partition (select products only)
HP Recovery Manager software allows you to remove the HP Recovery partition to free up hard drive space.
IMPORTANT: After you remove the HP Recovery partition, you will not be able to perform System Recovery
or create HP recovery media from the HP Recovery partition. So before you remove the Recovery partition,
create HP Recovery media; see Creating HP Recovery media (select products only) on page 114.
NOTE: The Remove Recovery Partition option is only available on products that support this function.
Follow these steps to remove the HP Recovery partition:
1. Type recovery in the taskbar search box, and then select HP Recovery Manager.
2. Select Remove Recovery Partition, and then follow the on-screen instructions.
118 Chapter 12 Backup and recovery – Windows 10
13 Backup and recovery – Windows 8
To protect your information, use Windows backup and restore utilities to back up individual files and folders,
back up your entire hard drive, create system repair media (select models only) by using the installed optical
drive (select models only) or an optional external optical drive, or create system restore points. In case of
system failure, you can use the backup files to restore the contents of your computer.
From the Start screen, type restore, click Settings, and then select from the list of displayed options.
IMPORTANT: If you will be using f11 startup recovery or USB media recovery to recover your system,
the tablet battery must have at least 70% battery power remaining before starting the recovery process.
NOTE: For detailed instructions on various backup and restore options, perform a search for these topics in
Windows Help and Support.
In case of system instability, HP recommends that you print the recovery procedures and save them for later
use.
NOTE: Windows includes the User Account Control feature to improve the security of your computer. You
may be prompted for your permission or password for tasks such as installing software, running utilities, or
changing Windows settings. For more information, see Windows Help and Support.
Backing up your information
Recovery after a system failure is as good as your most recent backup. You should create system repair
media and your initial backup immediately after initial system setup. As you add new software and data files,
you should continue to back up your system on a regular basis to maintain a reasonably current backup.
For more information on the Windows backup features, see Windows Help and Support.
Performing a system recovery
In case of system failure or instability, the computer provides the following tools to recover your files:
●Windows recovery tools: You can use Windows Backup and Restore to recover information you have
previously backed up. You can also use Windows Automatic Repair to fix problems that might prevent
Windows from starting correctly.
●f11 recovery tools: You can use the f11 recovery tools to recover your original hard drive image. The
image includes the Windows operating system and software programs installed at the factory.
NOTE: If you are unable to boot (start up) your computer and you cannot use the system repair media you
previously created (select models only), you must purchase Windows operating system media to reboot
the computer and repair the operating system. For additional information, see Using Windows operating
system media (purchased separately) on page 121.
Backing up your information 119
Using the Windows recovery tools
To recover information you previously backed up, see Windows Help and Support for steps on restoring files
and folders.
To recover your information using Automatic Repair, follow these steps:
CAUTION: Some Startup Repair options will completely erase and reformat the hard drive. All files you have
created and any software installed on the computer are permanently removed. When reformatting is
complete, the recovery process restores the operating system, as well as the drivers, software, and utilities
from the backup used for recovery.
1. If possible, back up all personal files.
2. If possible, check for the presence of the Recovery Image partition and the Windows partition.
From the Start screen, type file, and then click File Explorer.
– or –
From the Start screen, type pc, and then select This PC.
NOTE: If the Windows partition and the Recovery Image partition are not listed, you must recover your
operating system and programs using the Windows operating system DVD and the Driver Recovery
media (both purchased separately). For additional information, see Using Windows operating system
media (purchased separately) on page 121.
3. If the Windows partition and the Recovery Image partition are listed, restart the computer by pressing
and holding the shift key while clicking Restart.
4. Select Troubleshoot, then select Advanced Options, and then select Startup Repair.
5. Follow the on-screen instructions.
NOTE: For additional information on recovering information using the Windows tools, perform a search for
these topics in Windows Help and Support.
Using f11 recovery tools
CAUTION: Using f11 completely erases hard drive contents and reformats the hard drive. All files that you
have created and any software that you have installed on the computer are permanently removed. The f11
recovery tool reinstalls the operating system and HP programs and drivers that were installed at the factory.
Software not installed at the factory must be reinstalled.
To recover the original hard drive image using f11:
1. If possible, back up all personal files.
2. If possible, check for the presence of the Recovery Image partition: From the Start screen, type pc, and
then select This PC.
NOTE: If the Recovery Image partition is not listed, you must recover your operating system and
programs using the Windows operating system media and the Driver Recovery media (both purchased
separately). For additional information, see Using Windows operating system media (purchased
separately) on page 121.
3. If the Recovery Image partition is listed, restart the computer, and then press esc while the “Press
the ESC key for Startup Menu” message is displayed at the bottom of the screen.
120 Chapter 13 Backup and recovery – Windows 8
4. Press f11 while the “Press <F11> for recovery” message is displayed on the screen.
5. Follow the on-screen instructions.
Using Windows operating system media (purchased separately)
To order a Windows operating system DVD, contact support. See the Worldwide Telephone Numbers booklet
included with the computer. You can also find contact information from the HP website. Go to
http://www.hp.com/support, select your country or region, and follow the on-screen instructions.
CAUTION: Using a Windows operating system media completely erases hard drive contents and reformats
the hard drive. All files that you have created and any software that you have installed on the computer are
permanently removed. When reformatting is complete, the recovery process helps you restore the operating
system, as well as drivers, software, and utilities.
To initiate a full install of the operating system using a Windows operating system DVD:
NOTE: This process takes several minutes.
1. If possible, back up all personal files.
2. Insert the Windows operating system DVD into the optical drive, and then restart the computer.
3. When prompted, press any keyboard key.
4. Follow the on-screen instructions.
After the installation is completed:
1. Eject the Windows operating system media and then insert the Driver Recovery media.
2. Install the Hardware Enabling Drivers first, and then install Recommended Applications.
Performing a system recovery 121
Using Windows Refresh or Windows Reset
When your computer is not working properly and you need to regain system stability, the Windows Refresh
option allows you to start fresh and keep what is important to you.
The Windows Reset option allows you to perform detailed reformatting of your computer, or remove
personal information before you give away or recycle your computer. For more information on these
features, see Windows Help and Support.
Using HP Software Setup
HP Software Setup can be used to reinstall drivers or select software that has been corrupted or deleted from
the system.
1. From the Start screen, type HP Software Setup.
2. Open HP Software Setup.
3. Follow the on-screen directions to reinstall drivers or select software.
122 Chapter 13 Backup and recovery – Windows 8
14 Backup and recovery – Windows 7
Your computer includes HP and Windows tools to help you safeguard your information and retrieve it if you
ever need to. These tools will help you return your computer to a proper working state, all with simple steps.
This section provides information about the following processes:
●Creating recovery media and backups
●Restoring and recovering your system
Creating recovery media and backups
Recovery after a system failure is only as good as your most recent backup.
1. After you successfully set up the computer, create HP Recovery media. This step creates a Windows 7
operating system DVD and a Driver Recovery DVD. The Windows DVD can be used to reinstall the original
operating system in cases where the hard drive is corrupted or has been replaced. The Driver Recovery
DVD installs specific drivers and applications. See Creating recovery media with HP Recovery Disc
Creator on page 123.
2. Use Windows Backup and Recovery tools to perform the following:
●Back up individual files and folders
●Back up your entire hard drive (select models only)
●Create system repair discs (select models only) with the installed optical drive (select models only)
or an optional external optical drive
●Create system restore points
NOTE: This guide describes an overview of backing up, restoring, and recovering options. For more details
about the tools provided, see Help and Support. To access Help and Support, select Start > Help and
Support.
NOTE: HP recommends that you print the recovery procedures and save them for later use, in case of
system instability.
In case of system failure, you can use the backup files to restore the contents of your computer. See Backing
up your information on page 124.
Guidelines
●When creating recovery media or backing up to discs, use any of the following types of discs (purchased
separately): DVD+R, DVD+R DL, DVD-R, DVD-R DL, or DVD±RW. The discs you use will depend on
the type of optical drive you are using.
●Be sure that the computer is connected to AC power before you start the recovery media creation
process or the backup process.
Creating recovery media with HP Recovery Disc Creator
HP Recovery Disc Creator is a software program that offers an alternative way to create recovery media.
After you successfully set up the computer, you can create recovery media using HP Recovery Disc Creator.
This recovery media allows you to reinstall your original operating system as well as select drivers and
Creating recovery media and backups 123
applications if the hard drive becomes corrupted. HP Recovery Disc Creator can create two kinds of recovery
DVDs:
●Windows 7 operating system DVD—Installs the operating system without additional drivers or
applications.
●Driver Recovery DVD—Installs specific drivers and applications only, in the same way that the HP
Software Setup utility installs drivers and applications.
Creating recovery media
NOTE: The Windows 7 operating system DVD can be created only once. Thereafter, the option to create that
media will not be available after you create a Windows DVD.
To create the Windows DVD:
1. Select Start > All Programs > Productivity and Tools > HP Recovery Disc Creator.
2. Select Windows disk.
3. From the drop-down menu, select the drive for burning the recovery media.
4. Click the Create button to start the burning process.
After the Windows 7 operating system DVD has been created, create the Driver Recovery DVD:
1. Select Start > All Programs > Productivity and Tools > HP Recovery Disc Creator.
2. Select Driver disk.
3. From the drop-down menu, select the drive for burning the recovery media.
4. Click the Create button to start the burning process.
Backing up your information
You should create system repair media and your initial backup immediately after initial system setup. As you
add new software and data files, you should continue to back up your system on a regular basis to maintain a
reasonably current backup. You should also create Windows system repair media (select models only) which
can be used to start up (boot) the computer and repair the operating system in case of system instability or
failure. Your initial and subsequent backups allow you to restore your data and settings if a failure occurs.
You can back up your information to an optional external hard drive, a network drive, or discs.
Note the following when backing up:
●Store personal files in the Documents library, and back it up regularly.
●Back up templates that are stored in their associated directories.
●Save customized settings that appear in a window, toolbar, or menu bar by taking a screen shot of your
settings. The screen shot can be a time-saver if you have to reset your preferences.
●When backing up to discs, number each disc after removing it from the drive.
NOTE: For detailed instructions on various backup and restore options, perform a search for these topics in
Help and Support. To access Help and Support, select Start > Help and Support.
NOTE: Windows includes the User Account Control feature to improve the security of your computer. You
may be prompted for your permission or password for tasks such as installing software, running utilities, or
changing Windows settings. Refer to Help and Support. To access Help and Support, select Start > Help and
Support.
124 Chapter 14 Backup and recovery – Windows 7
To create a backup using Windows Backup and Restore:
NOTE: The backup process may take over an hour, depending on file size and the speed of the computer.
1. Select Start > All Programs > Maintenance > Backup and Restore.
2. Follow the on-screen instructions to set up your backup, create a system image (select models only), or
create system repair media (select models only).
Performing a system recovery
In case of system failure or instability, the computer provides the following tools to recover your files:
●Windows recovery tools: You can use Windows Backup and Restore to recover information you have
previously backed up. You can also use Windows Startup Repair to fix problems that might prevent
Windows from starting correctly.
●f11 recovery tools (select models only): You can use the f11 recovery tools to recover your original hard
drive image. The image includes the Windows operating system and software programs installed at
the factory.
NOTE: If you are unable to boot (start up) your computer and you cannot use the system repair media you
previously created (select models only), you must purchase Windows 7 operating system media to reboot
the computer and repair the operating system. For additional information, see Using Windows 7 operating
system media on page 126.
Using the Windows recovery tools
Using the Windows recovery tools, you can:
●Recover individual files
●Restore the computer to a previous system restore point
●Recover information using recovery tools
NOTE: For detailed instructions on various recovery and restore options, perform a search for these topics
in Help and Support. To access Help and Support, select Start > Help and Support.
NOTE: Windows includes the User Account Control feature to improve the security of your computer. You
may be prompted for your permission or password for tasks such as installing software, running utilities, or
changing Windows settings. Refer to Help and Support. To access Help and Support, select Start > Help and
Support.
To recover information you previously backed up:
1. Select Start > All Programs > Maintenance > Backup and Restore.
2. Follow the on-screen instructions to recover your system settings, your computer (select models only),
or your files.
To recover your information using Startup Repair, follow these steps:
CAUTION: Some Startup Repair options will completely erase and reformat the hard drive. All files you have
created and any software installed on the computer are permanently removed. When reformatting is
complete, the recovery process restores the operating system, as well as the drivers, software, and utilities
from the backup used for recovery.
Performing a system recovery 125
1. If possible, back up all personal files.
2. If possible, check for the presence of the Windows partition.
To check for the Windows partition, select Start > Computer.
NOTE: If the Windows partition is not listed, you must recover your operating system and programs
using the Windows 7 operating system DVD and the Driver Recovery media. For additional information,
see Using Windows 7 operating system media on page 126.
3. If the Windows partition is listed, restart the computer, and then press f8 before the Windows operating
system loads.
4. Select Startup Repair.
5. Follow the on-screen instructions.
NOTE: For additional information on recovering information using the Windows tools, select Start > Help
and Support.
Using f11 recovery tools (select models only)
CAUTION: Using f11 completely erases hard drive contents and reformats the hard drive. All files that you
have created and any software that you have installed on the computer are permanently removed. The f11
recovery tool reinstalls the operating system and HP programs and drivers that were installed at the factory.
Software not installed at the factory must be reinstalled.
To recover the original hard drive image using f11:
1. If possible, back up all personal files.
2. If possible, check for the presence of the HP Recovery partition: click Start, right-click Computer, click
Manage, and then click Disk Management.
NOTE: If the HP Recovery partition is not listed, you must recover your operating system and
programs using the Windows 7 operating system media and the Driver Recovery media. For additional
information, see Using Windows 7 operating system media on page 126.
3. If the HP Recovery partition is listed, restart the computer, and then press esc while the “Press the ESC
key for Startup Menu” message is displayed at the bottom of the screen.
4. Press f11 while the “Press <F11> for recovery” message is displayed on the screen.
5. Follow the on-screen instructions.
Using Windows 7 operating system media
If you cannot use the recovery media you previously created using the HP Recovery Disc Creator (select
models only), you must purchase a Windows 7 operating system DVD to reboot the computer and repair
the operating system.
To order a Windows 7 operating system DVD, go to the HP website. For U.S. support, go to
http://www.hp.com/support. For worldwide support, go to http://welcome.hp.com/country/us/en/
wwcontact_us.html. You can also order the DVD by calling support. For contact information, see
the Worldwide Telephone Numbers booklet included with the computer.
CAUTION: Using a Windows 7 operating system DVD completely erases hard drive contents and reformats
the hard drive. All files that you have created and any software that you have installed on the computer are
permanently removed. When reformatting is complete, the recovery process helps you restore the operating
system, as well as drivers, software, and utilities.
126 Chapter 14 Backup and recovery – Windows 7
To initiate recovery using a Windows 7 operating system DVD:
NOTE: This process takes several minutes.
1. If possible, back up all personal files.
2. Restart the computer, and then insert the Windows 7 operating system DVD into the optical drive before
the Windows operating system loads.
3. When prompted, press any keyboard key.
4. Follow the on-screen instructions.
5. Click Next.
6. Select Repair your computer.
7. Follow the on-screen instructions.
After the repair is completed:
1. Eject the Windows 7 operating system DVD and then insert the Driver Recovery DVD.
2. Install the Hardware Enabling Drivers first, and then install Recommended Applications.
Performing a system recovery 127
15 Statement of Volatility
The purpose of this document is to provide general information regarding non-volatile memory in industry-
standards based HP Business Notebook PC systems and provide general instructions for restoring
nonvolatile memory that can contain personal data after the system has been powered off and the hard drive
has been removed.
HP Business Notebook PC products that use Intel-based or AMD®-based system boards contain volatile DDR
memory. The amount of nonvolatile memory present in the system depends upon the system configuration.
Intel-based and AMD-based system boards contain nonvolatile memory subcomponents as originally
shipped from HP assuming that no subsequent modifications have been made to the system and assuming
that no applications, features, or functionality have been added to or installed on the system.
Following system shutdown and removal of all power sources from an HP Business Notebook PC system,
personal data can remain on volatile system memory (DIMMs) for a finite period of time and will also remain
in nonvolatile memory. The steps below will remove personal data from the notebook PC, including the
nonvolatile memory found in Intel-based and AMD-based system boards. Some of these steps are disclosed
in the Maintenance and Service Guides available for HP PC products available on the product support pages at
www.hp.com.
1. Follow steps (a) through (I) below to restore the nonvolatile memory that can contain personal data.
Restoring or re-programming nonvolatile memory that does not store personal data is neither
necessary nor recommended.
a. Enter BIOS (F10) Setup by powering on the system and pressing F10 when prompted near the
bottom of the display, or press the ESC key to display the start up menu, then press F10 . If the
system has a BIOS administrator password, enter the password at the prompt.
b. Select the File menu, then Restore Defaults.
c. Select the System Configuration menu, then Restore Security Defaults.
d. If an asset or ownership tag is set, select the Security menu and scroll down to the Utilities menu.
Select System IDs, and then select the tag that has been set. Press the spacebar once to clear the
tag, then press Enter to return to the prior menu.
e. If a DriveLock password is set, select the Security menu, scroll down to DriveLock, then select
DriveLock password. Select the desired hard drive. Click Disable protection, enter the existing
master DriveLock password, then press Enter to confirm and return to the prior menu. Repeat this
procedure if more than one hard drive has a DriveLock password.
f. If an Automatic DriveLock password is set, select the Security menu, scroll down to Automatic
DriveLock, then select the desired hard drive and disable protection. Repeat this procedure if
more than one hard drive has an Automatic DriveLock password.
g. Select the File menu, then Reset BIOS Security to factory default. Click yes at the warning
message.
h. Select the File menu, then Save Changes and Exit.
i. Reboot the system. If the system has a Trusted Platform Module and/or fingerprint sensor, one or
two prompts will appear: one to clear the TPM and the other to reset fingerprint sensor. Press F1
to accept or F2 to reject.
If the HP notebook model number ends in a ‘p’ or ‘w’ and includes Intel Centrino with VProTM,
reboot the PC and enter BIOS Setup by pressing F10 when prompted. Select System
128 Chapter 15 Statement of Volatility
Configuration, then AMT Options. Then select Un-configure AMT on next boot. Select Save, then
Yes. Select the File menu, and then select Save Changes and Exit. Reboot the system and confirm
that you want to un-configure AMT.
j. If the optional Intel Anti-Theft Technology (AT) was activated, contact the provider to deactivate it.
k. If the optional Absolute® Software Computrace® management and tracking service was activated
on the notebook PC, contact the provider to deactivate it.
l. Remove all power and system batteries for at least 24 hours.
2. Remove and retain the storage drive or clear the contents of the drive.
a. Hard Disk Drive (HDD)
Clear the HDD contents by using the HP Disk Sanitizer® utility or a third party application that,
ideally, is U.S. Department of Defense (DOD) 5220.22-M approved.
To run HP Disk Sanitizer, enter BIOS Setup by powering on the system and pressing F10 when
prompted near the bottom of the display, or press ESC to display the start up menu, then press
F10. Select the Security menu and scroll down to the Utilities menu. Select Disk Sanitizer and
select the desired drive. For a higher level of protection, select Optimum.
NOTE: This process will take a long time, and the amount of time varies based on the hard drive
capacity.
b. Solid State Drive (SSD)
Clear the SSD contents by using the BIOS Setup Secure Erase command option, or by using a third
party utility designed to erase data from an SSD. To run Secure Erase, enter BIOS Setup by
powering on the system and pressing F10 when prompted near the bottom of the display. Select
the Security menu and scroll down to the Utilities menu. Select Secure Erase and select the
desired hard drive.
129
Non-volatile memory usage
Non Volatile
Memory Type
Amount (Size) Does this
memory store
customer data?
Does this
memory retain
data when
power is
removed?
What is the
purpose of this
memory?
How is data
input into this
memory?
How is this
memory write
protected?
Real Time Clock
(RTC) battery
backed-up CMOS
configuration
memory (CMOS)
256 Bytes No Yes Stores system
date and time
and limited
keyboard
controller data.
Using the F10
Setup utility or
changing the
Microsoft
Windows date
and time.
This memory is
not write-
protected. HP
recommends
password
protecting the
F10 Setup
utility.
Controller (NIC)
EEPROM
64 KBytes (not
customer
accessible)
No Yes Store NIC
configuration
and NIC
firmware.
Using a utility
from the NIC
vendor that can
be run from DOS.
A utility is
required to write
data to this
memory and is
available from
NIC vendor.
Writing data to
this ROM in an
inappropriate
manner will
render the NIC
nonfunctional.
Keyboard ROM 64 KBytes (not
customer
accessible)
No Yes Stores firmware
code (keyboard,
mouse, &
battery
management).
Programmed at
the factory.
Code is updated
when the system
BIOS is updated.
A utility is
required for
writing data to
this memory and
is available on
the HP website.
Writing data to
this ROM in an
inappropriate
manner can
render the PC
nonfunctional.
DIMM Serial
Presence Detect
(SPD)
configuration
data
256 Bytes per
memory
module, 128
Bytes
programmable
(not customer
accessible)
No Yes Stores memory
module
information.
Programmed by
the memory
vendor.
Data cannot be
written to this
memory when
the module is
installed in a PC.
The specific
write protection
method varies
by memory
vendor.
System BIOS 4 to 5 MBytes Yes Yes Store system
BIOS code and
PC configuration
data.
System BIOS
code is
programmed at
the factory.
Code is updated
when the system
BIOS is updated.
Configuration
data and
settings are
A utility is
required for
writing data to
this memory and
is available on
the HP website.
Writing data to
this ROM in an
inappropriate
manner can
130 Chapter 15 Statement of Volatility
Non Volatile
Memory Type
Amount (Size) Does this
memory store
customer data?
Does this
memory retain
data when
power is
removed?
What is the
purpose of this
memory?
How is data
input into this
memory?
How is this
memory write
protected?
input using the
F10 setup utility
or a custom
utility.
render the PC
nonfunctional.
Intel
Management
Engine Firmware
(present only in
models ending in
a ‘p’ or ‘w’ or
with Intel
Centrino Pro
technology)
1.5 or 5 MBytes Yes Yes Stores
Management
Engine Code,
Settings,
Provisioning
Data and iAMT
third party data
store.
Management
Engine Code is
programmed at
the factory.
Code is updated
via Intel secure
firmware update
utility. Unique
Provisioning
Data can be
entered at the
factory or by an
administrator
using the
Management
Engine (MEBx)
setup utility. The
third party data
store contents
can populated
by a remote
management
console or local
applications
registered by an
administrator to
have access to
the space.
The Intel chipset
is configured to
enforce
hardware
protection to
block all direct
read/write
access to this
area. An Intel
utility is required
for updating the
firmware. Only
firmware
updates digitally
signed by Intel
can be applied
using this utility.
Bluetooth flash 2 MBits No Yes Stores Bluetooth
configuration
and firmware.
Programmed at
the factory.
Tools for writing
data to this
memory are not
publicly
available but can
be obtained
from the silicon
vendor.
A utility is
required for
writing data to
this memory and
is made
available
through newer
versions of the
driver if the flash
requires an
upgrade.
802.11 WLAN
EEPROM
4 KBytes to 8
KBytes
No Yes Stores
configuration
and calibration
data.
Programmed at
the factory.
Tools for writing
data to this
memory are not
made public.
A utility is
required for
writing data to
this memory and
is typically not
made available
to the public
unless a
firmware
upgrade is
necessary to
address a unique
issue.
Non-volatile memory usage 131
Non Volatile
Memory Type
Amount (Size) Does this
memory store
customer data?
Does this
memory retain
data when
power is
removed?
What is the
purpose of this
memory?
How is data
input into this
memory?
How is this
memory write
protected?
Webcamera 64 KBits No Yes Store
webcamera
configuration
and firmware.
Using a utility
from the device
manufacturer
that can be run
from Windows.
A utility is
required for
writing data to
this memory and
is typically not
made available
to the public
unless a
firmware
upgrade is
necessary to
address a unique
issue.
Fingerprint
reader
512 KBytes flash Yes Yes Stores
fingerprint
templates.
By enrolling in
HP ProtectTools
Security
Manager.
Only a digitally
signed
application can
make the call to
write to the
flash.
Questions and answers
1. How can the BIOS settings be restored (returned to default settings)?
a. Turn on or restart the slate and press F10 when prompted near the bottom of the display.
b. Select File, then select Restore defaults.
c. Follow the on-screen instructions.
d. Select File, save changes and exit, then press Enter.
2. What kind of configuration data is stored on the DIMM Serial Presence Detect (SPD) memory
module? How would this data be written?
The DIMM SPD memory contains information about the memory module such as size, serial number,
data width, speed/timing, voltage and thermal information. This information is written by the module
manufacturer and stored on an EEPROM. This EEPROM cannot be written to when the memory module is
installed in a PC. Third party tools do exist that can write to the EEPROM when the memory module is
not installed in a PC. There are various third party tools available to read SPD memory.
3. Does the “Firmware Hub for System BIOS” contain the BIOS program? Is this chip writable, and if so
how?
The Firmware Hub does contain the BIOS program and is writable. A utility is required to perform the
write function.
4. In some PC systems, the Firmware Hub for System BIOS is a flash memory chip so that updates can
be written by the customer. Is this true for these BIOS chips?
Yes, they are flash memory chips.
132 Chapter 15 Statement of Volatility
5. What is meant by “Restore the nonvolatile memory found in Intel-based system boards?”
This relates to clearing the Real Time Clock (RTC) CMOS memory that contains PC configuration data.
6. Does resetting the CMOS configuration memory return the PC back to factory defaults?
The process of resetting the CMOS will return certain system settings to factory default but will not
reset many of the system data and configuration defaults to their default settings. To return these
system data and configuration defaults to default settings, refer to question and answer 1 and follow
the instructions for returning the BIOS settings to factory defaults.
Questions and answers 133
16 Backup and recovery – Windows 7
Your slate includes HP and Windows tools to help you safeguard your information and retrieve it if you ever
need to. These tools will help you return your slate to a proper working state, all with simple steps. This
section provides information about the following processes:
●Creating recovery media and backups
●Restoring and recovering your system
Creating recovery media and backups
Recovery after a system failure is only as good as your most recent backup.
1. After you successfully set up the slate, create HP Recovery media. This step creates a Windows 7
operating system DVD and a Driver Recovery DVD. The Windows DVD can be used to reinstall the original
operating system in cases where the hard drive is corrupted or has been replaced. The Driver Recovery
DVD installs specific drivers and applications. See Creating recovery media with HP Recovery Disc
Creator on page 123.
2. Use Windows Backup and Recovery tools to perform the following:
●Back up individual files and folders
●Back up your entire hard drive (select models only)
●Create system repair discs (select models only) with the installed optical drive (select models only)
or an optional external optical drive
●Create system restore points
NOTE: This guide describes an overview of backing up, restoring, and recovering options. For more details
about the tools provided, see Help and Support. To access Help and Support, select Start > Help and
Support.
NOTE: HP recommends that you print the recovery procedures and save them for later use, in case of
system instability.
In case of system failure, you can use the backup files to restore the contents of your slate. See Backing up
your information on page 124.
Guidelines
●When creating recovery media or backing up to discs, use any of the following types of discs (purchased
separately): DVD+R, DVD+R DL, DVD-R, DVD-R DL, or DVD±RW. The discs you use will depend on the
type of optical drive you are using.
●Be sure that the slate is connected to AC power before you start the recovery media creation process or
the backup process.
Creating recovery media with HP Recovery Disc Creator
HP Recovery Disc Creator is a software program that offers an alternative way to create recovery media.
After you successfully set up the slate, you can create recovery media using HP Recovery Disc Creator. This
recovery media allows you to reinstall your original operating system as well as select drivers and
134 Chapter 16 Backup and recovery – Windows 7
applications if the hard drive becomes corrupted. HP Recovery Disc Creator can create two kinds of recovery
DVDs:
●Windows 7 operating system DVD—Installs the operating system without additional drivers or
applications.
●Driver Recovery DVD—Installs specific drivers and applications only, in the same way that the HP
Software Setup utility installs drivers and applications.
Creating recovery media
NOTE: The Windows 7 operating system DVD can be created only once. Thereafter, the option to create that
media will not be available after you create a Windows DVD.
To create the Windows DVD:
1. Select Start > All Programs > Productivity and Tools > HP Recovery Disc Creator.
2. Select Windows disk.
3. From the drop-down menu, select the drive for burning the recovery media.
4. Click the Create button to start the burning process.
After the Windows 7 operating system DVD has been created, create the Driver Recovery DVD:
1. Select Start > All Programs > Productivity and Tools > HP Recovery Disc Creator.
2. Select Driver disk.
3. From the drop-down menu, select the drive for burning the recovery media.
4. Click the Create button to start the burning process.
Backing up your information
You should create system repair media and your initial backup immediately after initial system setup. As you
add new software and data files, you should continue to back up your system on a regular basis to maintain a
reasonably current backup. You should also create Windows system repair media (select models only) which
can be used to start up (boot) the slate and repair the operating system in case of system instability or
failure. Your initial and subsequent backups allow you to restore your data and settings if a failure occurs.
You can back up your information to an optional external hard drive, a network drive, or discs.
Note the following when backing up:
●Store personal files in the Documents library, and back it up regularly.
●Back up templates that are stored in their associated directories.
●Save customized settings that appear in a window, toolbar, or menu bar by taking a screen shot of your
settings. The screen shot can be a time-saver if you have to reset your preferences.
●When backing up to discs, number each disc after removing it from the drive.
NOTE: For detailed instructions on various backup and restore options, perform a search for these topics in
Help and Support. To access Help and Support, select Start > Help and Support.
NOTE: Windows includes the User Account Control feature to improve the security of your slate. You may
be prompted for your permission or password for tasks such as installing software, running utilities, or
changing Windows settings. Refer to Help and Support. To access Help and Support, select Start > Help and
Support.
Creating recovery media and backups 135
To create a backup using Windows Backup and Restore:
NOTE: The backup process may take over an hour, depending on file size and the speed of the slate.
1. Select Start > All Programs > Maintenance > Backup and Restore.
2. Follow the on-screen instructions to set up your backup, create a system image (select models only), or
create system repair media (select models only).
Performing a system recovery
In case of system failure or instability, the slate provides the following tools to recover your files:
●Windows recovery tools: You can use Windows Backup and Restore to recover information you have
previously backed up. You can also use Windows Startup Repair to fix problems that might prevent
Windows from starting correctly.
●f11 recovery tools (select models only): You can use the f11 recovery tools to recover your original hard
drive image. The image includes the Windows operating system and software programs installed at the
factory.
NOTE: If you are unable to boot (start up) your slate and you cannot use the system repair media you
previously created (select models only), you must purchase Windows 7 operating system media to reboot the
slate and repair the operating system. For additional information, see Using Windows 7 operating system
media on page 126.
Using the Windows recovery tools
Using the Windows recovery tools, you can:
●Recover individual files
●Restore the slate to a previous system restore point
●Recover information using recovery tools
NOTE: For detailed instructions on various recovery and restore options, perform a search for these topics
in Help and Support. To access Help and Support, select Start > Help and Support.
NOTE: Windows includes the User Account Control feature to improve the security of your slate. You may
be prompted for your permission or password for tasks such as installing software, running utilities, or
changing Windows settings. Refer to Help and Support. To access Help and Support, select Start > Help and
Support.
To recover information you previously backed up:
1. Select Start > All Programs > Maintenance > Backup and Restore.
2. Follow the on-screen instructions to recover your system settings, your slate (select models only), or
your files.
To recover your information using Startup Repair, follow these steps:
CAUTION: Some Startup Repair options will completely erase and reformat the hard drive. All files you have
created and any software installed on the slate are permanently removed. When reformatting is complete,
the recovery process restores the operating system, as well as the drivers, software, and utilities from the
backup used for recovery.
136 Chapter 16 Backup and recovery – Windows 7
1. If possible, back up all personal files.
2. If possible, check for the presence of the Windows partition.
To check for the Windows partition, select Start > Slate.
NOTE: If the Windows partition is not listed, you must recover your operating system and programs
using the Windows 7 operating system DVD and the Driver Recovery media. For additional information,
see Using Windows 7 operating system media on page 126.
3. If the Windows partition is listed, restart the slate, and then press f8 before the Windows operating
system loads.
4. Select Startup Repair.
5. Follow the on-screen instructions.
NOTE: For additional information on recovering information using the Windows tools, select Start > Help
and Support.
Using f11 recovery tools (select models only)
CAUTION: Using f11 completely erases hard drive contents and reformats the hard drive. All files that you
have created and any software that you have installed on the slate are permanently removed. The f11
recovery tool reinstalls the operating system and HP programs and drivers that were installed at the factory.
Software not installed at the factory must be reinstalled.
To recover the original hard drive image using f11:
1. If possible, back up all personal files.
2. If possible, check for the presence of the HP Recovery partition: click Start, right-click Slate, click
Manage, and then click Disk Management.
NOTE: If the HP Recovery partition is not listed, you must recover your operating system and
programs using the Windows 7 operating system media and the Driver Recovery media. For additional
information, see Using Windows 7 operating system media on page 126.
3. If the HP Recovery partition is listed, restart the slate, and then press esc while the “Press the ESC key
for Startup Menu” message is displayed at the bottom of the screen.
4. Press f11 while the “Press <F11> for recovery” message is displayed on the screen.
5. Follow the on-screen instructions.
Using Windows 7 operating system media
If you cannot use the recovery media you previously created using the HP Recovery Disc Creator (select
models only), you must purchase a Windows 7 operating system DVD to reboot the slate and repair the
operating system.
To order a Windows 7 operating system DVD, go to the HP website. For U.S. support, go to
http://www.hp.com/support. For worldwide support, go to http://welcome.hp.com/country/us/en/
wwcontact_us.html. You can also order the DVD by calling support. For contact information, see the
Worldwide Telephone Numbers booklet included with the slate.
CAUTION: Using a Windows 7 operating system DVD completely erases hard drive contents and reformats
the hard drive. All files that you have created and any software that you have installed on the slate are
permanently removed. When reformatting is complete, the recovery process helps you restore the operating
system, as well as drivers, software, and utilities.
Performing a system recovery 137
To initiate recovery using a Windows 7 operating system DVD:
NOTE: This process takes several minutes.
1. If possible, back up all personal files.
2. Restart the slate, and then insert the Windows 7 operating system DVD into the optical drive before the
Windows operating system loads.
3. When prompted, press any keyboard key.
4. Follow the on-screen instructions.
5. Click Next.
6. Select Repair your slate.
7. Follow the on-screen instructions.
After the repair is completed:
1. Eject the Windows 7 operating system DVD and then insert the Driver Recovery DVD.
2. Install the Hardware Enabling Drivers first, and then install Recommended Applications.
138 Chapter 16 Backup and recovery – Windows 7
17 Power cord set requirements
The wide-range input feature of the slate permits it to operate from any line voltage from 100 to 120 volts
AC, or from 220 to 240 volts AC.
The 3-conductor power cord set included with the slate meets the requirements for use in the country or
region where the equipment is purchased.
Power cord sets for use in other countries and regions must meet the requirements of the country or region
where the slate is used.
Requirements for all countries
The following requirements are applicable to all countries and regions:
●The length of the power cord set must be at least 1.0 m (3.3 ft) and no more than 2.0 m (6.5 ft).
●All power cord sets must be approved by an acceptable accredited agency responsible for evaluation in
the country or region where the power cord set will be used.
●The power cord sets must have a minimum current capacity of 10 amps and a nominal voltage rating of
125 or 250 V AC, as required by the power system of each country or region.
●The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320 Standard Sheet
C13 connector for mating with the appliance inlet on the back of the slate. Requirements for all
countries 113
Requirements for specific countries and regions
Country/region Accredited agency Applicable note number
Australia EANSW 1
Austria OVE 1
Belgium CEBC 1
Canada CSA 2
Denmark DEMKO 1
Finland FIMKO 1
France UTE 1
Germany VDE 1
Italy IMQ 1
Japan METI 3
The Netherlands KEMA 1
Norway NEMKO 1
The People's Republic of China COC 5
Requirements for all countries 139
Country/region Accredited agency Applicable note number
South Korea EK 4
Sweden CEMKO 1
Switzerland SEV 1
Taiwan BSMI 4
The United Kingdom BSI 1
The United States UL 2
1. The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler and
wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be
used.
2. The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole grounding type
with a NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.
3. The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the
Japanese Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00-mm² conductor size. The wall plug must
be a two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V) configuration.
4. The flexible cord must be Type RVV, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler and wall
plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.
5. The flexible cord must be Type VCTF, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler and wall
plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.
140 Chapter 17 Power cord set requirements
18 Recycling
When a non-rechargeable or rechargeable battery has reached the end of its useful life, do not dispose of the
battery in general household waste. Follow the local laws and regulations in your area for battery disposal.
HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable
batteries. For more information about recycling programs, see the HP Web site at http://www.hp.com/
recycle.
141
Index
A
AC adapter, spare part numbers 26
AC adapter/battery light 17
adapter port 7
alignment post 11
alignment post connector 7
alignment post connector bracket
removal 49
spare part number 22, 50
ambient light sensor 9
antenna
location 9
removal 67, 70, 71
spare part numbers 67, 70, 71
Antenna Kit, spare part numbers
22, 67, 70, 71
audio jack board
removal 51
spare part number 23, 51
audio, product description 1
audio-in (microphone) jack 7, 15
audio-out (headphone) jack 7, 15
B
back cover
removal 35
spare part number 23, 35
Backup and Restore 125, 136
backup tools 123, 134
backups
creating 124, 135
recovering 125, 136
battery
removal 39, 75
spare part numbers 22, 26, 39,
75
BIOS
determining version 100, 107
downloading an update 100,
107
updating 100, 107
bottom cover
removal 74
spare part number 26, 74
Bracket Kit, spare part numbers 26
buttons
left TouchPad 14
power 7, 16
right TouchPad 14
rotate lock 6
volume 6, 15
Windows 10
C
Cable Kit, spare part numbers 26
cables, service considerations 30
camera flash 6
caps lock light 13
chipset, product description 1
components
display 9
keyboard base 11
keyboard base keys 12
keyboard base left side 15
keyboard base lights 13
keyboard base right side 16
keyboard base TouchPad 14
slate edge 6
Computer Setup
navigating and selecting 98,
105
restoring factory settings 99,
106
connector board
removal 83
spare part number 25, 83
connector board bracket
removal 84
spare part number 84
connectors
alignment post 7
docking 11
power 17
service considerations 30
D
digitizer pen, spare part number 27
display components 9
display panel assembly
removal 35
spare part numbers 20, 35
display panel cable
removal 37
spare part number 21, 38
display panel, product description 1
DisplayPort 17
docking connector 11
docking connector board
removal 49
spare part number 23, 49
docking connector board bracket
removal 49
spare part number 50
docking connector board cable
removal 72
spare part number 23, 72
docking port 7
Driver Recovery DVD,
creating 123, 134
using for restore 126, 137
E
electrostatic discharge 31
embedded numeric keypad 12
equipment guidelines 33
esc key 12
external media cards, product
description 2
F
f11 recovery 120, 126, 137
fan
removal 46
spare part number 21, 46
fingerprint reader 11
fingerprint reader board
removal 80
spare part number 25, 80
fingerprint reader board bracket
removal 80
spare part number 80
142 Index
fingerprint reader board cable
removal 87, 88
spare part number 87, 88
fn key 12
front-facing webcam
location 9
removal 65
spare part number 21, 65
function keys 12
G
graphics, product description 1
grounding guidelines 31
guidelines
equipment 33
grounding 31
packaging 32
transporting 32
workstation 32
H
hard drive recovery 120, 126, 137
headphone (audio-out) jack 7, 15
heat sink
removal 62
spare part number 21, 62
hinge assembly
removal 89
spare part number 26, 89
HP PC Hardware Diagnostics (UEFI)
downloading 103
using 103
HP Recovery Disc Creator, using
123, 134
HP Recovery partition
checking for presence 126, 137
using for recovery 126, 137
J
jacks
audio-in (microphone) 7, 15
audio-out (headphone) 7, 15
K
keyboard
removal 77
spare part numbers 24, 27, 77
keyboard base
components 11
key components 12
left-side components 15
light components 13
right-side components 16
spare part numbers 24
TouchPad components 14
keyboard base system board
removal 84
spare part number 84
keys
embedded numeric 12
esc 12
fn 12
function 12
num lock 12
numeric keypad 12
Windows 12
kickstand
removal 88
spare part number 26, 88
Kickstand Hinge Kit, spare part
number 26, 88
L
LCD rotation lock 15
legacy support, USB 98, 105
lights
AC adapter/battery 17
caps lock 13
microphone mute 13
mute 13
num lock 13
TouchPad 13
webcam 9
wireless 13
M
memory card 7
memory card reader 7
memory, product description 1
Micro SD memory card reader 17
microphone 6, 9, 16
microphone (audio-in) jack 7, 15
microphone mute light 13
microphone, product description 1
model name 1
mute light 13
N
num lock light 13
numeric keypad keys 12
O
operating system, product
description 3, 4, 5
P
packaging guidelines 32
pen holder 7
plastic parts, service
considerations 30
Plastics Kit, spare part number 28
ports
adapter 7
DisplayPort 17
docking 7
product description 2
USB 3.0 17
power button 7, 16
power button actuator, installation
56
power connector 17
power connector cable
removal 76
spare part number 26, 76
power connector cable bracket
removal 77, 86
spare part number 77, 86
power cord
set requirements 139
spare part numbers 28, 29
power requirements, product
description 2, 3
primary storage, product
description 1
processor, product description 1
product description
audio 1
chipset 1
display panel 1
external media cards 2
graphics 1
memory 1
microphone 1
operating system 3, 4, 5
ports 2
power requirements 2, 3
primary storage 1
processors 1
product name 1
security 3
serviceability 5
Index 143
video 1
wireless 1, 2
product name 1
R
rear-facing webcam
location 6
removal 64
spare part number 21, 64
recovery 122
recovery media
creating 123
using for restore 126
recovery media, creating 134
recovery media, using for restore
137
recovery partition 120, 126, 137
recovery tools 123, 134
recovery tools, Windows 125, 136
recovery, system 125, 136
refresh 122
release latch 11
removal/replacement procedures
34
keyboard base 74
reset 122
restoring the hard drive 120, 126,
137
rotate lock button 6
RTC battery
removal 59
spare part number 20, 59
Rubber Kit, spare part number 26
S
Screw Kit, spare part number 29
security, product description 3
service considerations
cables 30
connectors 30
plastic parts 30
serviceability, product description 5
setup utility
navigating and selecting 98,
105
restoring factory settings 99,
106
SIM card slot 7, 17
SIM/SD card release access 7, 17
slate
major components 20
specifications 112
slate edge components 6
slots
memory card reader 7
smart card 16
smart card reader board
removal 82
spare part number 25, 82
smart card slot 16
solid-state drive
removal 60
spare part numbers 22, 60
speaker grille
removal 35
spare part number 20, 35
speakers
location 9
removal 44
spare part number 22, 44
Startup Repair, using 125, 136
Sure Start 104
system board
removal 52
spare part numbers 21, 26, 52
T
tools required 30
top cover, spare part number 25
TouchPad
buttons 14
removal 81
spare part number 25, 81
TouchPad light 13
TouchPad zone 14
transporting guidelines 32
U
USB 3.0 port 15, 17
USB legacy support 98, 105
USB ports 15
V
vents 6
vibrator module
removal 45
spare part number 22, 45
video, product description 1
volume button 6, 15
volume button board
removal 47
spare part number 21, 47
volume button board bracket
removal 48
spare part number 21, 48
volume button board cable
removal 58
spare part number 58
W
webcam
location 6, 9
spare part numbers 21
webcam light 9
WiGig antenna
location 9
removal 71
spare part number 22, 71
Windows
Refresh 122
Reset 122
Windows 7 operating system DVD
creating 123, 134
using for restore 126, 137
Windows 7 operating system media
creating 123, 134
using for restore 126, 137
Windows button 10
Windows key 12
Windows operating system DVD
121
Windows Startup Repair, using 125,
136
wireless antenna
location 9
removal 67, 70, 71
spare part numbers 67, 70, 71
wireless light 13
wireless, product description 1, 2
WLAN antenna
location 9
removal 70
spare part numbers 22, 70
WLAN module
removal 40
spare part numbers 21, 40
workstation guidelines 32
WWAN antenna
location 9
144 Index
