iiyama P1905S-B2 User Manual
Displayed below is the user manual for P1905S-B2 by iiyama which is a product in the Computer Monitors category. This manual has pages.
Related Manuals
ENGLISH
USER MANUAL
Thank you very much for choosing the iiyama
LCD monitor.
We recommend that you take a few minutes
to read this comprehensive manual carefully
before installing and switching on the monitor.
Please keep this manual in a safe place for
your future reference.
ENGLISH
ENGLISH
We reserve the right to change specifi cations without notice.
All trademarks used in this user manual are the property of their respective owners.
As an ENERGY STAR® Partner, iiyama has determined that this product meets the ENERGY STAR® guidelines
for energy effi ciency.
We recommend recycling of used product. Please contact your dealer or iiyama
service center. Recycle information is obtained via the Internet, using the address:
http://www.iiyama.com
You can access the Web page of diff erent countries from there.
A certified power supply cord has to be used with this equipment. The relevant national
installation and/or equipment regulations shall be considered. A certified power supply cord
not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation
H05VV-F 3G 0.75mm2 or H05VVH2-F2 3G 0.75mm2) shall be used. Alternative a fl exible cord be
of synthetic rubber according to IEC 60245 (designation H05RR-F 3G 0.75mm2) shall be used.
CE MARKING DECLARATION OF CONFORMITY
This LCD monitor complies with the requirements of the EC/EU Directive 2014/30/EU “EMC
Directive”, 2014/35/EU “Low Voltage Directive”, 2009/125/EC “ErP Directive” and 2011/65/EU
“RoHS Directive”.
The electro-magnetic susceptibility has been chosen at a level that gives correct operation in
residential areas, business and light industrial premises and small-scale enterprises, inside as
well as outside of the buildings. All places of operation are characterised by their connection to
the public low voltage power supply system.
IIYAMA CORPORATION: Wijkermeerstraat 8, 2131 HA Hoofddorp, The Netherlands
Model No. : PLP1900
ENGLISH
FOR YOUR SAFETY ................................................................................................. 1
SAFETY PRECAUTIONS ................................................................................... 1
SPECIAL NOTES ON LCD MONITORS ............................................................. 3
CUSTOMER SERVICE ....................................................................................... 3
CLEANING .......................................................................................................... 3
BEFORE YOU OPERATE THE MONITOR ............................................................... 4
FEATURES ......................................................................................................... 4
CHECKING THE CONTENTS OF THE PACKAGE ............................................ 4
WALL MOUNTING .............................................................................................. 5
FITTING AND REMOVAL OF BASE ................................................................... 6
CONTROLS AND CONNECTORS ..................................................................... 7
CONNECTING YOUR MONITOR ....................................................................... 8
COMPUTER SETTING ....................................................................................... 9
ADJUSTING THE VIEWING ANGLE ................................................................. 9
OPERATING THE MONITOR .................................................................................... 10
ADJUSTMENT MENU CONTENTS .................................................................... 11
SCREEN ADJUSTMENTS .................................................................................. 17
POWER MANAGEMENT FEATURE .................................................................. 20
TROUBLE SHOOTING ............................................................................................. 21
RECYCLING INFORMATION .................................................................................... 22
APPENDIX ............................................................................................................... 23
SPECIFICATIONS ............................................................................................. 23
DIMENSIONS ..................................................................................................... 24
COMPLIANT TIMING .......................................................................................... 24
TABLE OF CONTENTS
ENGLISH
FOR YOUR SAFETY 1
FOR YOUR SAFETY
WARNING
STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE
If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the
monitor and contact your dealer or iiyama service center immediately. Further use may be
dangerous and can cause fi re or electric shock.
NEVER REMOVE THE CABINET
High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of
fi re or electric shock.
DO NOT PUT ANY OBJECT INTO THE MONITOR
Do not put any solid objects or liquids such as water into the monitor. In case of an accident, unplug
your monitor immediately and contact your dealer or iiyama service center. Using the monitor with
any object inside may cause fi re, electric shock or damage.
INSTALL THE MONITOR ON A FLAT, STABLE SURFACE
The monitor may cause an injury if it falls or is dropped.
DO NOT USE THE MONITOR NEAR WATER
Do not use where water may be splashed or spilt onto the monitor as it may cause fi re or electric
shock.
OPERATE UNDER THE SPECIFIED POWER SUPPLY
Be sure to operate the monitor only with the specifi ed power supply. Use of an incorrect voltage will
cause malfunction and may cause fi re or electric shock.
PROTECT THE CABLES
Do not pull or bend the power cable and signal cable. Do not place the monitor or any other heavy
objects on the cables. If damaged, the cables may cause fi re or electric shock.
ADVERSE WEATHER CONDITIONS
It is advisable not to operate the monitor during a heavy thunder storm as the continual breaks in
power may cause malfunction. It is also advised not to touch the plug in these circumstances as it
may cause electric shock.
SAFETY PRECAUTIONS
ENGLISH
2 FOR YOUR SAFETY
CAUTION
INSTALLATION LOCATION
Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or
smoky areas as it may cause fi re, electric shock or damage. You should also avoid areas where the
sun shines directly on the monitor.
DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION
The monitor may topple and cause injury if not suitably located. Please also ensure that you do not
place any heavy objects on the monitor, and that all cables are routed such that children may not
pull the cables and possibly cause injury.
MAINTAIN GOOD VENTILATION
Ventilation slots are provided to keep the monitor from overheating. Covering the slots may cause
fi re. To allow adequate air circulation, place the monitor at least 10 cm (or 4 inches) from any walls.
Do not remove the tilt stand when operating the monitor. Ventilation slots on the back of the
cabinet will be blocked and the monitor may overheat if the stand is removed. This may cause fi re
or damage. Operating the monitor on its back, side, upside down or on a carpet or any other soft
material may also cause damage.
DISCONNECT THE CABLES WHEN YOU MOVE THE MONITOR
When you move the monitor, turn off the power switch, unplug the monitor and be sure the signal
cable is disconnected. If you do not disconnect them, it may cause fi re or electric shock.
UNPLUG THE MONITOR
If the monitor is not in use for a long period of time it is recommended that it is left unplugged to avoid accidents.
HOLD THE PLUG WHEN DISCONNECTING
To disconnect the power cable or signal cable, always pull it by the plug. Never pull on the cable
itself as this may cause fi re or electric shock.
DO NOT TOUCH THE PLUG WITH WET HANDS
Pulling or inserting the plug with wet hands may cause electric shock.
WHEN YOU INSTALL THE MONITOR ON YOUR COMPUTER
Be sure the computer is strong enough to hold the weight of the monitor, otherwise, you may
damage your computer.
REMARK FOR 24/7 USAGE
This product is not specifi cally designed for 24/7 usage in all environments.
ERGONOMIC RECOMMENDATIONS
To eliminate eye fatigue, do not operate the monitor against a bright background or in a dark room.
For optimal viewing comfort, the monitor should be just below eye level and 40-60 cm (16-24 inches)
away from your eyes. When using the monitor over a prolonged time, a ten minute break every hour
is recommended as looking at the screen continuously can cause eye strain.
OTHERS
ENGLISH
FOR YOUR SAFETY 3
The following symptoms are normal with LCD monitors and do not indicate a problem.
NOTE
When you first turn on the LCD monitor, the picture may not fit in the display area
because of the type of computer that is used. In this case, adjust the picture position to
the correct position.
Due to the nature of the backlight, the screen may fl icker during initial use. Turn off the
Power Switch and then turn it on again to make sure the fl icker disappears.
You may find slightly uneven brightness on the screen depending on the desktop
pattern you use.
Due to the nature of the LCD screen, an afterimage of the previous screen may remain
after switching the image, when the same image is displayed for hours. In this case, the
screen is recovered slowly by changing the image or turning off the Power Switch for
hours.
Contact your dealer or iiyama service center for the backlight replacement when the
screen is dark, fl ickering or not lighting up. Never attempt to replace it by yourself.
SPECIAL NOTES ON LCD MONITORS
NOTE
The fl uorescent light used in the LCD monitor may have to be periodically replaced.
For the warranty coverage on this component, please check with local iiyama service
center.
If you have to return your unit for service and the original packaging has been
discarded, please contact your dealer or iiyama service center for advice or
replacement packaging.
WARNING
If you drop any materials or liquids such as water into the monitor when cleaning,
unplug the power cable immediately and contact your dealer or iiyama service center.
CAUTION
For safety reasons, turn off the power switch and unplug the monitor before you
clean it.
NOTE
To protect the LCD panel, do not scratch or rub the screen with a hard object.
Never use any of the following strong solvents. These will damage the cabinet and the
LCD screen.
Touching the cabinet with any product made from rubber or plastic for a long time may
cause degeneration or loss of paint on the cabinet.
Thinner
Benzine
Abrasive cleaner
Spray-type cleaner
Wax
Acid or Alkaline solvent
CABINET Stains can be removed with a cloth lightly moistened with a mild detergent solvent.
Then wipe the cabinet with a soft dry cloth.
LCD
SCREEN
Periodic cleaning with a soft dry cloth is recommended.
Don't use tissue paper etc. because these will damage the LCD screen.
CUSTOMER SERVICE
CLEANING
ENGLISH
4 BEFORE YOU OPERATE THE MONITOR
The following accessories are included in your package. Check to see if they are enclosed with
the monitor. If anything is missing or damaged, please contact your local iiyama dealer or regional
iiyama offi ce.
* The rating of the Power Cable enclosed in 120V area is 10A/125V. If you are using
a power supply higher than this rating, then a power cable with a rating of 10A/
250V must be used. However, all guarantees and warranties are void for any
problems or damage caused by a power cable not supplied by iiyama.
An approved power cord greater or equal to H05VVF, 3G, 0.75mm2 must be
used.
Power Cable*
VGA Cable DVI-D Cable
Audio Cable Stand-Base Safety Guide
Quick Start Guide
BEFORE YOU OPERATE THE MONITOR
CHECKING THE CONTENTS OF THE PACKAGE
CAUTION
FEATURES
Supports Resolutions up to 1280 × 1024
High Contrast 1000:1 (Typical), Adv. Contrast Function Available / Brightness
240cd/m2 (Typical) / Quick Response Time 5ms (Black, White, Black)
Digital Character Smoothing
Automatic Set-up
Stereo Speakers
2 × 1W Stereo Speakers
Plug & Play VESA DDC2B Compliant
Windows® 7/8.1/10 Compliant
Power Management (ENERGY STAR® VESA DPMS Compliant)
VESA Mounting Standard (100mm×100mm) Compliant
Keyhole for Security Lock
ENGLISH
BEFORE YOU OPERATE THE MONITOR 5
When you use with the wall mounting, in consideration of thickness of the mounting
stage, tighten the M4 Screw with washer which “L” length is 7mm to fasten the
monitor. Using the screw longer than this may cause electric shock or damage
because it may contact with the electrical parts inside the monitor.
Please check if the wall or ceiling can support the weight of the monitor before
mounting it.
WALL MOUNTING
WARNING
Screw
Chassis
Mounting Stage
L
ENGLISH
6 BEFORE YOU OPERATE THE MONITOR
Put the monitor on a stable surface. The monitor may cause injury or damage if it
falls or is dropped.
Do not give a strong impact to the monitor. It may cause damage.
Unplug the monitor before removal or installation to avoid electric shock or damage.
CAUTION
FITTING AND REMOVAL OF BASE
<Installation>
Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched.
Lay the monitor fl at on a table with front face down.
Install the stand-base to the monitor (A) and slide the stand-base to the back of the monitor (B).
<Removal>
Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched.
Lay the monitor fl at on a table with front face down.
Press and hold the hook outside and slide the stand-base to the front of the monitor (C), and pull
the stand-base from the monitor (D).
Stand-Base
(C)
(D)
(A)
(B)
Hook
ENGLISH
BEFORE YOU OPERATE THE MONITOR 7
CONTROLS AND CONNECTORS
<Front> <Back>
Power Switch ( ) / Power Indicator
Blue: Normal operation
Orange: Power Management
Select / Input select Button ( )
Scroll up / Audio Adjust Button ( )
Scroll Down / i-Style Color Button ( )
Menu Button( )
Speakers
VGA Connector(VGA)
DVI-D Connector(DVI)
Audio Connector (AUDIO)
Keyhole for Security Lock
You can fasten a security lock and cable to prevent the monitor from being removed
without yourpermission.
AC Connector ( : Alternating current) (AC IN)
NOTE
NOTE
2
1
ENGLISH
8 BEFORE YOU OPERATE THE MONITOR
CONNECTING YOUR MONITOR
Ensure that both the computer and the monitor are switched off .
Connect the computer to the monitor with the signal cable.
Connect the monitor to the audio equipment with the Audio Cable for computer when using the
audio features.
Connect the Power Cable to the monitor fi rst and then to the power supply.
Power of the monitor and the computer is turned on.
The signal cables used for connecting the computer and monitor may vary with the
type of computer used. An incorrect connection may cause serious damage to both
the monitor and the computer. The cable supplied with the monitor is for a standard
connector. If a special cable is required please contact your local iiyama dealer or
regional iiyama offi ce.
For connection to Macintosh computers, contact your local iiyama dealer or regional
iiyama offi ce for a suitable adaptor.
Make sure you tighten the fi nger screws at each end of the signal cable.
The Class I pluggable equipment Type A must be connected to protective earth.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
[Example of Connection]
<Back>
NOTE
Power Cable
(Accessory)
Audio Cable (Accessory)
VGA Cable (Accessory)
DVI-D Cable (Accessory)
Computer
ENGLISH
BEFORE YOU OPERATE THE MONITOR 9
Signal Timing
Change to the desired signal timing listed on page 24: COMPLIANT TIMING.
COMPUTER SETTING
20
‑TOP‑
ADJUSTING THE VIEWING ANGLE
For optimal viewing it is recommended to look at the full
face of the monitor.
Hold the stand so that the monitor does not topple when
you change the monitor’s angle.
You are able to adjust the monitor’s angle up to 20
degrees upward.
In order to ensure a healthy and relaxed body position
when using the monitor at visual display workstations, it
is recommended that the adjusted tilt angle should not
exceed 10 degrees. Adjust the monitor’s angle to your
own preference.
Do not press down heavily on the glass when
you change the angle. It may cause damage or
break the LCD screen.
Careful attention is required not to catch your
fi ngers or hands when you change the angle.
NOTE
ENGLISH
10 OPERATING THE MONITOR
OPERATING THE MONITOR
To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT
TIMING shown on page 24. You are also able to adjust the picture by following the button operation
shown below. For more detailed adjustments, see page 17 for SCREEN ADJUSTMENTS.
Press the 1 Button to start the On Screen Display (OSD) feature. There are
additional Menu items which can be switched by using the / Buttons.
Select the Menu item which contains the adjustment icon relating to the adjustment
you want to make. Press the 2 Button. Then, use the / Buttons to highlight
the desired adjustment icon.
Press the 2 Button again. Use the / Buttons to make the appropriate
adjustment or setting.
Press the 1 Button to leave the menu, and the settings you just made would be
automatically saved.
When button operations are aborted during adjustment, On-Screen Display disappears
when the time set for the OSD Time Out has passed. Also, the 1 button can be used
to return previous menu and turn off the On-Screen Display.
Any changes are automatically saved in the memory when the On Screen Display
disappears. Turning off the power should be avoided while using the Menu.
Adjustments for H./V. Position, Clock and Phase are saved for each signal timing. Except for
these adjustments, all other adjustments have only one setting which applies to all signal timings.
For example, to correct for vertical position, select Menu item of Manual Image Adjust and then
press the 2 Button. Then, select H./V.Position by using the / Buttons.
An adjustment page appears after you press the 2 Button. Then, select V. Position by using
the / Buttons. Press the 2 Button again. Then, use the / Buttons to change
the vertical position settings. The vertical position of the overall display should be changing
accordingly while you are doing this.
Press the 1 Button lastly, it ends, all changes are saved in the memory.
NOTE
Manual Image Adjust
H./V. Position
H. Position
V. Position
▲
▲
50
▲
▲
50
1 : E x i t S e l e c t : 2
Picture Adjust
Input Select
Audio Adjust
Color Adjust
Information
Manual Image Adjust
Setup Menu
Memory Recall
Auto Image Adjust
1 : E x i t S e l e c t : 2
Picture Adjust
Input Select
Audio Adjust
Color Adjust
Information
Setup Menu
Memory Recall
Auto Image Adjust
Manual Image Adjust
1 : E x i t S e l e c t : 2
H./V. Position
Clock
Phase
Sharpness
Manual Image Adjust
1 : E x i t S e l e c t : 2
ENGLISH
OPERATING THE MONITOR 11
ADJUSTMENT MENU CONTENTS
Adjustment Item Problem / Option Button to Press
Auto Image Adjust
Auto Image Adjust * Adjust H. / V. Position, Clock and Phase automatically.
* For best results, use the Auto Image Adjust in conjunction with the adjustment pattern. See page
17 for SCREEN ADJUSTMENTS.
Only Analog Input
You can skip the Menu items and display an adjustment scale directly by using the following button
operations.
Auto Image Adjust: Pressing and holding of the Button for about 2 seconds when the Menu is
not displayed.
Direct
Direct
Auto Image Adjust
Too dark
Too bright
Brightness *1,2,3
Too dull
Too intense
*1 Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too
bright. Can not select when Adv. Contrast is On.
*2 Brightness and Adv. Contrast can not enable the same time when ECO Mode is on.
*3 Contrast, Brightness, Adv. Contrast and ECO Mode adjustments are disabled when i-Style Color
is activated.
*4 To activate the option, mark it in the setup menu. To deactivate it, remove the marking.
Brightness of back-light is reduced.
Off Normal
ECO Mode *3
Adv. Contrast *2,3,4
Increased Contrast RatioOn
Off Typical Contrast Ratio
Adjustment Item Problem / Option Button to Press
Picture Adjust
Contrast *3
1
Brightness of back-light is reduced more than 1.2
Brightness of back-light is reduced more than 2.3
Picture Adjust
ENGLISH
12 OPERATING THE MONITOR
Adjustment Item Problem / Option Button to Press
Input Select
Input Select
You can skip the Menu items and display an adjustment scale directly by using the following button
operations.
Input Select: Press the 2Button when the Menu is not displayed.
Direct
Direct
Input source is fi xed, not selected automatically when VGA and DVI which are selected.
Select the VGA input.
Select the DVI input.
VGA
DVI
Auto
Search for an available input source and select
automatically.
NOTE
Volume Too soft
Too loud
Adjustment Item Problem / Option Button to Press
Audio Adjust
Mute *
Direct
Direct
Return the sound volume to the previous level.
Turn off the sound temporarily.
* To activate the option, mark it in the setup menu. To deactivate it, remove the marking.
You can skip the Menu items and display an adjustment scale directly by using the following button
operations.
Audio Adjust: Press the Button when the Menu is not displayed.
Mute: Pressing and holding of the Button for about 2 seconds when the Menu is not
displayed.
Mute and Unmute are switched as follows by pressing the Button successively.
Input Select
Audio Adjust
Off
On
Direct
ENGLISH
OPERATING THE MONITOR 13
Information
See your graphic card user guide for more information
about changing the resolution and refresh.
Displays information regarding the current input signal coming
from the graphic card in your computer.
NOTE
Too weak
Too strong
Adjustment Item Problem / Option Button to Press
Color Adjust
User Color
You can skip the Menu items and display an adjustment scale directly by using the following button
operations.
i-Style Color: Press the Button when the Menu is not displayed.
Direct
Direct
Bluish white
Red
Green
Blue
Cool
Reddish white Normal
Greenish white Warm
i-Style Color
Standard For general windows environment and monitor
default setting.
Text For text editing and viewing in a word processing
environment.
Game For PC game environment.
Cinema For movie and video environment.
Scenery For displaying outdoor scenery images
Off Return to a state set by color adjustment except
i-Style Color.
<Example>
Color Adjust
Information
Resolution:
H.Frequency:
V.Frequency:
Pixel Clock:
Model Number:
Information
1280x1024
64.00KHz
60.0Hz
108.0MHz
P1905S
1 : E x i t S e l e c t : 2
ENGLISH
14 OPERATING THE MONITOR
Too left
Too right
Too low
Too high
Too narrow
Too wide
To correct fl ickering text or lines
*1 Only Analog Input.
*2 See page 16 for SCREEN ADJUSTMENTS.
Adjustment Item Problem / Option Button to Press
Manual Image Adjust
Clock *1
H./V. Position *1,2
H. Position
V. Position
Phase *1
Sharpness
0 1 2 3
You can change the picture quality from 0 to 3 (soft to sharp).
Press the Button to change the picture quality in numerical
order. Press the Button to change the picture quality in
reverse numerical order.
Adjust the picture quality at resolutions of less 1280 x 1024.
You can change the picture quality (4 steps).
Manual Image Adjust
ENGLISH
OPERATING THE MONITOR 15
Memory Recall Factory-preset data is restored.
English
Deutsch
English
German
Français French Japanese
Russian
Polski Polish
Simplifi ed Chinese
Nederlands Dutch
Русский
H.Position OSD is too left
OSD is too right
OSD is too low
OSD is too high
You can set the OSD display duration time.
5 / 15 / 30 / 60 seconds
V.Position
Adjustment Item Problem / Option Button to Press
Setup Menu
Language Select
OSD Position
OSD Time Out
OSD Background*
LED*
The background of OSD is mode transparent.
Off Retune the background of OSD.
On
The Power Indicator is turned On.
Off The Power Indicator is turned Off .
On
Turn Off the Power Indicator when you are bothered by the light.
NOTE
Adjustment Item Problem / Option Button to Press
Memory Recall
iiyama Logo displayed when the monitor is turned on.
On
Off iiyama Logo does not display when the monitor is
turned on.
Opening Logo*
Setup Menu
Memory Recall
* To activate the option, mark it in the setup menu. To deactivate it, remove the marking.
Traditional Chinese
ENGLISH
16 OPERATING THE MONITOR
● Lock Mode
<OSD Menu>
1. The OSD lock will be activated by pressing the front buttons 1and for about 10 seconds. If
you try to access the OSD by pressing any of the buttons 1, , and 2, message "OSD
Locked" will appear on the screen.
2. The OSD lock will be deactivated by pressing the front buttons 1and again for 10 seconds.
<Power Switch>
1. The power switch lock will be activated by pressing the front buttons 1and for 10 seconds.
Locking the power switch means that won't be able to turn off the Monitor while the power switch
is locked. If presses the power switch message "Power Button Locked" will appear on the screen.
2. The power switch lock will be deactivated by pressing the front buttons 1and again for about
10 seconds.
ENGLISH
OPERATING THE MONITOR 17
SCREEN ADJUSTMENTS
The screen adjustments described in this manual are designed to set image position and minimize
fl icker or blur for the particular computer in use.
The monitor is designed to provide the best performance at resolution of 1280 × 1024, but can
not provide the best at resolutions of less than 1280 × 1024 because the picture is automatically
stretched to fi t the full screen. It is recommended to operate at resolution of 1280 × 1024 in normal
use.
Displayed text or lines will be blurred or irregular in thickness when the picture is stretched due to
the screen enlargement process.
It is preferable to adjust the image position and frequency with the monitor controls, rather than
the computer software or utilities.
Perform adjustments after a warm-up period of at least thirty minutes.
Additional adjustments may be required after the Auto Image Adjust depending on the resolution
or signal timing.
The Auto Image Adjust may not work correctly when displaying the picture other than the screen
adjustment pattern. In this case, manual adjustments are required.
There are two ways to adjust the screen. One way is automatic adjustment for Position, Horizontal
Size and Fine Tune. The other way is performing each adjustment manually.
Perform the Auto Image Adjust fi rst when the monitor is connected to a new computer, or resolution
is changed. If the screen has a fl icker or blur, or the picture does not fi t in the display area after
performing the Auto Image Adjust, manual adjustments are required. Both adjustments should be
made by using the screen adjustment pattern (Test.bmp) obtained via the IIYAMA website (http://
www.iiyama.com).
Adjust the image by following the procedure below to get the desired picture.
This manual explains adjustment under Windows® OS.
Display the picture at the optimum resolution.
Enter the Test.bmp (screen adjustment pattern) to wallpaper.
Consult the appropriate documentation for doing this.
Test.bmp is made at resolution of 1280 × 1024. Set the display position to center in
the wallpaper setting dialogue box.
[Adjustment pattern]
Zebra pattern
Color bar
Picture frame
NOTE
Adjust the image by following the procedure below to get the desired picture when selecting Analog input.
ENGLISH
18 OPERATING THE MONITOR
1) Adjust the H.Position so that the left side of the picture frame will move to the left
edge of the display area.
When the left side of the picture frame moves apart from the left edge of the display
area during the Horizontal Size adjustment, adjust steps 1) and 2).
Another way to make the Horizontal Size adjustment is to correct the vertical wavy
lines in the zebra pattern.
The picture may flicker during the Horizontal Size, H.Position and V.Position
adjustment.
In case the picture frame is bigger or smaller than the data display area after the
Horizontal Size adjustment, repeat steps from .
2) Stretch the right side of the picture frame to the right edge of the display area by
adjusting the Horizontal Size.
Pressing and holding of the Button for about 2 seconds when the Menu is not
displayed. (Auto Image Adjust)
Adjust the image manually by following procedure below when the screen has a fl icker or
blur, or the picture does not fi t in the display area after performing the Auto Image Adjust.
Adjust the V.Position so that the top and bottom of the picture frame will fi t to the display
area.
NOTE
ENGLISH
OPERATING THE MONITOR 19
In case the strong fl icker or blurs remain on a part of the screen, repeat steps and
because the Horizontal Size may not be adjusted correctly. If the fl icker or blurs
still remain, set the refresh rate of computer to low (60Hz) and repeat steps from
again.
Adjust the H.Position after the Fine Tune adjustment if the horizontal position moves
during the adjustment.
Adjust the Brightness and Color Adjust to get the desired picture after you complete the
Horizontal Size and Fine Tune adjustments.
Put back your favorite wallpaper.
Adjust the Fine Tune to correct horizontal wavy noise, fl icker or blur in the zebra pattern.
NOTE
ENGLISH
20 OPERATING THE MONITOR
Even when using the power management mode, the monitor consumes electricity. Turn
off the Power Switch whenever the monitor is not in use, during the night and weekends,
to avoid unnecessary power consumption.
It is possible that the video signal from the computer may be on while the H or V sync
signal is missing. In this instance, the POWER MANAGEMENT feature may not work
properly.
NOTE
POWER MANAGEMENT FEATURE
Power Management Mode
When the H-sync signal / V-sync signal / H and V sync signals from the computer are off , the
monitor enters into Power Management Mode which reduces the power consumption to less
than 0.5W. The screen becomes dark, and the power indicator turns to orange. From Power
Management Mode, the image reappears in several seconds when either the keyboard or the
mouse are touched again.
The power management feature of this product complies with power saving requirement of ENERGY
STAR® and VESA DPMS. When activated, it automatically reduces unnecessary power consumption
of the monitor when your computer is not in use.
To use the feature, the monitor needs to be connected to a VESA DPMS compliant computer.
There is a power management step the monitor takes as described below. The power management
function, including any timer settings is confi gured by the operating system. Check your operating
system manual for information on how this can be confi gured.
0 0.5W 100%
POWER
CONSUMPTION
Blue
Orange
Power Indicator
NORMAL MODE
POWER MANAGEMENT MODE
ENGLISH
TROUBLE SHOOTING 21
TROUBLE SHOOTING
1. Perform the adjustments described in OPERATING THE MONITOR, depending on the problem
you have. If the monitor does not get a picture, skip to 2.
2. Consult the following items if you cannot fi nd an appropriate adjustment item in OPERATING THE
MONITOR or if the problem persists.
3. If you are experiencing a problem which is not described below or you cannot correct the problem,
discontinue using the monitor and contact your dealer or iiyama service center for further
assistance.
Problem Check
(Power indicator
is orange.)
The screen is not
synchronized.
The Signal Cable is properly connected.
The signal timing of the computer is within the specifi cation of the monitor.
The video output level of the computer is within the specifi cation of the
monitor.
The screen
position is not in
the center.
The signal timing of the computer is within the specifi cation of the monitor.
The screen is too
bright or too dark.
The screen is
shaking.
The video output level of the computer is within the specifi cation of the
monitor.
The power voltage is within the specifi cation of the monitor.
The signal timing of the computer is within the specifi cation of the monitor.
If the monitor fails to operate correctly, please follow the steps below for a possible solution.
(Power indicator
is blue.)
The picture does
not appear.
(Power indicator
does not light up.)
The Power Cable is fi rmly seated in the socket.
The Power Switch is turned ON.
The AC socket is live. Please check with another piece of equipment.
If the blank screen saver is in active mode, touch the keyboard or the
mouse.
Increase the Contrast and/or Brightness.
The computer is ON.
The Signal Cable is properly connected.
The signal timing of the computer is within the specifi cation of the monitor.
If the monitor is in power management mode, touch the keyboard or the
mouse.
The computer is ON.
The Signal Cable is properly connected.
The signal timing of the computer is within the specifi cation of the monitor.
ENGLISH
22 TROUBLE SHOOTING / RECYCLING INFORMATION
Problem Check
No sound.
The audio equipment (computer etc.) is ON.
The Audio Cable is properly connected.
The Volume is turned up.
The Mute is OFF.
The audio output level of the audio equipment is within the specifi cation of
the monitor.
The sound is too
loud or too quiet.
The audio output level of the audio equipment is within the specifi cation of
the monitor.
A strange noise
is heard.
The Audio Cable is properly connected.
For better environment protection please don't dispose your monitor.
Please visit our website: www.iiyama.com/recycle for monitor recycling.
RECYCLING INFORMATION
ENGLISH
APPENDIX 23
APPENDIX
Design and specifi cations are subject to change without prior notice.
SPECIFICATIONS
LCD Panel
Panel technology
TN
0.294mm H × 0.294mm V
Response time
Pixel pitch
5ms (Black, White, Black)
Display Colors Approx.16.7M
Sync Frequency Horizontal: 30.0-80.0kHz, Vertical: 55-75Hz
Maximum Resolution 1280 × 1024, 1.3 MegaPixels
Input Connector VGA, DVI-D
Input Sync Signal Separate sync: TTL, Positive or Negative
Plug & Play VESA DDC2BTM
16W typical, Power management mode: 0.5W maximum*Power Consumption
Dimensions / Net Weight 414.5× 420.5 × 200.5mm / 16.3 × 16.6 × 7.9" (W×H×D)
4.6kg / 10.14lbs
Upward: 20 degrees
Viewable angle
Right / Left : 85 degrees each, Up / Down : 80 degrees each (Typical)
Maximum Screen Size 376.320mm W × 301.056mm H / 14.8" W × 11.9" H
Power Source 100-240VAC, 50/60Hz, 0.6A
Environmental
Considerations
Approvals CE, Energy Star®
Tilt Angle
* Audio equipment is not connected.
NOTE
Brightness
Contrast ratio
240cd/m2 (Typical)
1000 : 1 (Typical), Adv. Contrast Function Available
Analog: 0.7Vp-p (Standard), 75Positive
Digital: DVI (Digital Visual Interface Standard Rev.1.0) compliance
Input Video Signal
Input Audio Signal 1.0Vrms maximum
Speakers 1W × 2 (Stereo speakers)
Input Audio Connector ø 3.5mm mini jack (Stereo)
Operating: Temperature
Humidity
Storage: -20 to 60°C / -4 to 140°F
Humidity
5 to 35°C / 41 to 95°F
5 to 85% (No condensation)
10 to 80% (No condensation)
Temperature
Size Category 19"
Diagonal: 19" (48cm)Size
ENGLISH
24 APPENDIX
DIMENSIONS
362.5mm/14.3"
303.0mm/11.9"
70.5mm/2.78"
420.5mm/16.6"
200.5mm/7.89"
201.5mm/7.93"
414.5mm/16.3"
378.0mm/14.9"
COMPLIANT TIMING
Dot Clock
25.175MHz
31.500MHz
31.500MHz
36.000MHz
40.000MHz
50.000MHz
49.500MHz
65.000MHz
75.000MHz
78.750MHz
108.000MHz
135.000MHz
Vertical
Frequency
59.940Hz
75.000Hz
72.809Hz
56.250Hz
60.316Hz
72.188Hz
75.000Hz
60.004Hz
70.069Hz
75.029Hz
60.020Hz
75.025Hz
VESA
SVGA
VGA
XGA 1024 × 768
640 × 480
800 × 600
Video Mode
SXGA 1280 × 1024
Horizontal
Frequency
31.469kHz
37.500kHz
37.861kHz
35.156kHz
37.879kHz
48.077kHz
46.875kHz
48.363kHz
56.476kHz
60.023kHz
63.981kHz
79.976kHz
M063E22