iiyama S3820HSB-B1 User Manual
Displayed below is the user manual for S3820HSB-B1 by iiyama which is a product in the Signage Displays category. This manual has pages.
Related Manuals
ENGLISH
Thank you very much for choosing the iiyama
LCD monitor.
We recommend that you take a few minutes
to read this comprehensive manual carefully
before installing and switching on the monitor.
Please keep this manual in a safe place for
your future reference.
USER MANUAL
ENGLISH
Wereservetherighttochangespecicationswithoutnotice.
All trademarks used in this user manual are the property of their respective owners.
We recommend recycling of used product. Please contact your dealer or iiyama
service center. Recycle information is obtained via the Internet, using the
address: http://www.iiyama.com
YoucanaccesstheWebpageofdierentcountriesfromthere.
CE MARKING DECLARATION OF CONFORMITY
This LCD monitor complies with the requirements of the EC/EU Directive 2014/30/EU “EMC
Directive”, 2014/35/EU “Low Voltage Directive” and 2011/65/EU “RoHS Directive”.
Warning
This is a class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
IIYAMA CORPORATION: Wijkermeerstraat 8, 2131 HA Hoofddorp, The Netherlands
Model No. : PL3820HB
ENGLISH
TABLE OF CONTENTS
FOR YOUR SAFETY ............................................................................ 1
SAFETY PRECAUTIONS................................................................1
SPECIAL NOTES ON LCD MONITORS .........................................3
CUSTOMER SERVICE ...................................................................5
CLEANING ......................................................................................5
BEFORE YOU OPERATE THE MONITOR ..........................................6
FEATURES......................................................................................6
CHECKING THE CONTENTS OF THE PACKAGE ........................6
CONTROLS AND CONNECTORS : MONITOR ..............................7
INSTALLATION ...............................................................................9
CONNECTING YOUR MONITOR ................................................. 11
COMPUTER SETTING .................................................................12
OPERATING THE MONITOR .............................................................13
ADJUSTMENT MENU CONTENTS ..............................................15
SCREEN ADJUSTMENTS ............................................................22
TROUBLE SHOOTING ......................................................................25
RECYCLING INFORMATION .............................................................26
APPENDIX ........................................................................................27
SPECIFICATIONS : ProLite S3820HSB .......................................27
DIMENSIONS : ProLite S3820HSB ..............................................28
COMPLIANT TIMING ....................................................................28
ENGLISH
FOR YOUR SAFETY 1
FOR YOUR SAFETY
WARNING
STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE
If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the
monitor and contact your dealer or iiyama service center immediately. Further use may be
dangerousandcancausereorelectricshock.
NEVER REMOVE THE CABINET
High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of
reorelectricshock.
DO NOT PUT ANY OBJECT INTO THE MONITOR
Do not put any solid objects or liquids such as water into the monitor. In case of an accident, unplug
your monitor immediately and contact your dealer or iiyama service center. Using the monitor with
anyobjectinsidemaycausere,electricshockordamage.
INSTALL THE MONITOR ON A FLAT, STABLE SURFACE
The monitor may cause an injury if it falls or is dropped.
DO NOT USE THE MONITOR NEAR WATER
Donotusewherewatermaybesplashedorspiltontothemonitorasitmaycausereorelectric
shock.
OPERATE UNDER THE SPECIFIED POWER SUPPLY
Besuretooperatethemonitoronlywiththespeciedpowersupply.Useofanincorrectvoltagewill
causemalfunctionandmaycausereorelectricshock.
PROTECT THE CABLES
Do not pull or bend the power cable and signal cable. Do not place the monitor or any other heavy
objectsonthecables.Ifdamaged,thecablesmaycausereorelectricshock.
ADVERSE WEATHER CONDITIONS
It is advisable not to operate the monitor during a heavy thunder storm as the continual breaks in
power may cause malfunction. It is also advised not to touch the plug in these circumstances as it
may cause electric shock.
SAFETY PRECAUTIONS
ENGLISH
2 FOR YOUR SAFETY
CAUTION
INSTALLATION LOCATION
Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or
smokyareasasitmaycausere,electricshockordamage.Youshouldalsoavoidareaswherethe
sun shines directly on the monitor.
DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION
The monitor may topple and cause injury if not suitably located. Please also ensure that you do not
place any heavy objects on the monitor, and that all cables are routed such that children may not
pull the cables and possibly cause injury.
MAINTAIN GOOD VENTILATION
Ventilation slots are provided to keep the monitor from overheating. Covering the slots may cause
re.Toallowadequateaircirculation,placethemonitoratleast10cm(or4inches)fromanywalls.
Operating the monitor on its back, side, upside down or on a carpet or any other soft material may
also cause damage.
DISCONNECT THE CABLES WHEN YOU MOVE THE MONITOR
Whenyoumovethemonitor,turnothepowerswitch,unplugthemonitorandbesurethesignal
cableisdisconnected.Ifyoudonotdisconnectthem,itmaycausereorelectricshock.
UNPLUG THE MONITOR
If the monitor is not in use for a long period of time it is recommended that it is left unplugged to
avoid accidents.
HOLD THE PLUG WHEN DISCONNECTING
To disconnect the power cable or signal cable, always pull it by the plug. Never pull on the cable
itselfasthismaycausereorelectricshock.
DO NOT TOUCH THE PLUG WITH WET HANDS
Pulling or inserting the plug with wet hands may cause electric shock.
WHEN YOU INSTALL THE MONITOR ON YOUR COMPUTER
Be sure the computer is strong enough to hold the weight of the monitor, otherwise, you may
damage your computer.
ERGONOMIC RECOMMENDATIONS
To eliminate eye fatigue, do not operate the monitor against a bright background or in a dark room.
Foroptimalviewingcomfort,themonitorshouldbejustbeloweyeleveland40-60cm(16-24inches)
away from your eyes. When using the monitor over a prolonged time, a ten minute break every hour
is recommended as looking at the screen continuously can cause eye strain.
OTHERS
ENGLISH
FOR YOUR SAFETY 3
The following symptoms are normal with LCD monitors and do not indicate a problem.
NOTE -WhenyourstturnontheLCDmonitor,thepicturemaynottinthedisplayarea
because of the type of computer that is used. In this case, adjust the picture position to
the correct position.
-Youmayndslightlyunevenbrightnessonthescreendependingonthedesktop
pattern you use.
- Due to the nature of the LCD screen, an afterimage of the previous screen may remain
after switching the image, when the same image is displayed for hours. In this case, the
screenisrecoveredslowlybychangingtheimageorturningothePowerSwitchfor
hours.
SPECIAL NOTES ON LCD MONITORS
This LCD cannot be used outdoors.
This LCD cannot be used with the screen facing upwards.
If you use a cable longer than the supplied one, the picture quality is not guaranteed.
ENGLISH
4 FOR YOUR SAFETY
USAGE CONFIRMATION
This product is designed for optimum usage at 24hours per day.
The display is compatible for usage in Landscape/Portrait applications.
IMAGE PERSISTENCE / IMAGE STICKING
Please be aware that all LCD screens can experience Image Persistence or Image Sticking. This
occurs when a residual image remains visible on a screen when static images are displayed for long
periods of time. LCD Image Persistence is not permanent but constant images being displayed for a
long period of time should be avoided.
To counteract Image Persistence, turn off the monitor for as long as the previous image was
displayed, so if an image was on the monitor for 1 hour and there is evidence of a residual or “ghost”
image,youshouldturnothemonitorfor1hourinordertocleartheresidualimage.
For all LFD products, iiyama recommends displaying moving images and utilising a moving screen
saveratregularintervalswheneverthescreenisidle.Youcouldalsoturnothemonitorwhennot
in use to assist the prevention.
Other waystoreducetheriskofImagePersistencewillbetoutilisetheFAN-onfunction(if
available),LowBacklightandLowBrightnesssettings.
FOR EXTENDED USE AS A PUBLIC DISPLAY
Image Sticking on LCD Panel
When a static image is displayed for hours, an electric charge trace remains near the electrode
insidetheLCDproducinga“ghost”image.(ImagePersistence).
Image Persistence is not a permanent feature.
Recommendations
To prevent Image Sticking and promote longer life expectancy of display, we recommend the
following:
1. Avoid static images displayed for long periods – change static images on continuous loop.
2.Turnomonitorwhennotinuse,eitherbyremotecontrolorusePowerManagementorSchedule
functions.
3.Whenmonitorisinstalledinhighambienttemperatureenvironment(s)orinanenclosedposition,
utilise the Cooling Fan, Screen Saver and Low Brightness functions.
4. Suitable ventilation for any monitor is an expectation of any installation – climate control systems
may need to be employed.
5. We strongly recommend utilisation of active cooling with fans for long operation times or high
ambient temperature environments.
ENGLISH
FOR YOUR SAFETY 5
NOTE
If you have to return your unit for service and the original packaging has been
discarded, please contact your dealer or iiyama service center for advice or
replacement packaging.
WARNING
If you drop any materials or liquids such as water into the monitor when cleaning,
unplug the power cable immediately and contact your dealer or iiyama service center.
CAUTION
For safety reasons, turn o the power switch and unplug the monitor before you
clean it.
NOTE
To protect the LCD panel, do not scratch or rub the screen with a hard object.
Never use any of the following strong solvents. These will damage the cabinet and
the LCD screen.
Touching the cabinet with any product made from rubber or plastic for a long time
may cause degeneration or loss of paint on the cabinet.
Thinner Benzine Abrasive cleaner
Spray-type cleaner Wax Acid or Alkaline solvent
CABINET Stains can be removed with a cloth lightly moistened with a mild detergent solvent.
Then wipe the cabinet with a soft dry cloth.
LCD
SCREEN
Periodic cleaning with a soft dry cloth is recommended.
Don't use tissue paper etc. because these will damage the LCD screen.
CUSTOMER SERVICE
CLEANING
ENGLISH
6 BEFORE YOU OPERATE THE MONITOR
The following accessories are included in your package. Check to see if they are enclosed with
the monitor. If anything is missing or damaged, please contact your local iiyama dealer or regional
iiyamaoce.
* 1. TO USERS IN 120V AREA
The rating of the Power Cable enclosed in 120V area is 10A/125V. If you are
using a power supply higher than this rating, then a power cable with a rating of
10A/250V must be used. However, all guarantees and warranties are void for any
problems or damage caused by a power cable or AC adapter not supplied by
iiyama.
2. Applicable AC Adapter
AC Adapter Type Name :
2ABF060ForKPL-060F-VI(ChannelWellTechnologyCo.,Ltd.)
3.
An approved power cord greater or equal to H05VVF, 3G, 0.75mm
2
must be used.
Power Cable*
AC Adapter*
HDMI Cable
RS-232C Cable Light Sensor Cable Safety Guide
Quick Start Guide
BEFORE YOU OPERATE THE MONITOR
CHECKING THE CONTENTS OF THE PACKAGE
CAUTION
FEATURES
Supports Resolutions up to 1920 × 540
High Contrast 4000:1 (Typical) / Brightness 1000cd/m2 (Typical)
Automatic Set-up
Stereo Speakers
2 × 5W Stereo Speakers
Plug & Play VESA DDC2B Compliant
Windows® 7/8.1/10 Compliant
Power Management (VESA DPMS Compliant)
VESA Mounting Standard (400mm×100mm) Compliant
Support 24hrs/day usage (by moving picture condition)
ENGLISH
BEFORE YOU OPERATE THE MONITOR 7
CONTROLS AND CONNECTORS : MONITOR
<Back Controller>
<Front>
Power Button
Power Indicator
Green Normal Operation
Red Power Management
O PowerO
Increase / Input Select Button
Menu / Enter Button
Decrease / Brightness Button
ENGLISH
8 BEFORE YOU OPERATE THE MONITOR
<Back>
DC IN DC jack ConnectorforACAdapter( :Directcurrent)(DC-IN)
VGA VGA VGA Connector
DVI DVI-D DVI-D Connector
RS232 RS-232C 9pin RS-232C Connector
AUDIO IN
(PCAudioIn) Mini Jack Audio Connector
LIGHT SENSOR Light Sensor Light Sensor Connector
HDMI HDMI HDMI Connector
SPEAKERS Speakers
HANDLES
Handles
ENGLISH
BEFORE YOU OPERATE THE MONITOR 9
INSTALLATION
CAUTION
Follow the manual instructions for the type of mount you have selected. Refer all servicing to
qualiedservicepersonnel.
Moving the monitor requires at least two people.
Before installing, please make sure the wall is strong enough to hold the necessary weight of the
display and the mount.
[WALL MOUNTING]
When using the wall mounting, consideration of thickness of the mounting stage needs to be taken.
Tighten the M6 Screw with washer which “L” length is 11mm to fasten the monitor. Using a screw
longer than this may cause electric shock or damage because it may contact with the electrical parts
inside the monitor.
CAUTION
L
Mounting Stage Screw
Chassis
ENGLISH
10 BEFORE YOU OPERATE THE MONITOR
[ROTATING THE DISPLAY]
It is designed to be compatible in both landscape and portrait modes.
Landscape
Portrait
Available Not Available
Portrait
A
A
A
A
ENGLISH
BEFORE YOU OPERATE THE MONITOR 11
CONNECTING YOUR MONITOR
Ensurethatboththecomputerandthemonitorareswitchedo.
Connect the computer to the monitor with the signal cable.
Connect the Light Sensor Cable to the monitor.
ConnectthePowerCabletothemonitorrstandthentothepowersource.
Turn on your monitor and computer.
The signal cables used for connecting the computer and monitor may vary with the
type of computer used. An incorrect connection may cause serious damage to both
the monitor and the computer. The cable supplied with the monitor is for a standard
connector. If a special cable is required please contact your local iiyama dealer or
regionaliiyamaoce.
For connection to Macintosh computers, contact your local iiyama dealer or regional
iiyamaoceforasuitableadaptor.
MakesureyoutightenthengerscrewsateachendoftheSignalCable.
The Class I pluggable equipment Type A must be connected to protective earth.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
[Example of Connection]
<Back>
NOTE
Computer
AV Equipment
VGA Cable (Not Included)*
HDMI Cable (Accessory)
DVI-D Cable (Not Included)*
RS-232C Cable (Accessory)
Power Cable
(Accessory)
AC Adapter
(Accessory)
Audio Cable (Not Included)
Light Sensor Cable (Accessory)
* Cable is not supplied with the monitor. If you use low quality cable, it may cause a result of electro-
magnetic interference. Please contact the iiyama Support Centre in your country if you wish to
connect the monitor via the VGA or DVI input.
ENGLISH
12 BEFORE YOU OPERATE THE MONITOR
Signal Timing
Change to the desired signal timing listed on page 28: COMPLIANT TIMING.
COMPUTER SETTING
ENGLISH
OPERATING THE MONITOR 13
OPERATING THE MONITOR
To create the best picture, your iiyama LCD monitor has been preset at the factory with the
COMPLIANT TIMING shown on page 28. You are also able to adjust the picture by following
the button operation shown below. For more detailed adjustments, see page 22 for SCREEN
ADJUSTMENTS.
Press the MENU button to start the On Screen Display feature. There are additional
Menu items which can be switched by using the / buttons.
Select the Menu item of the adjustment you want to make. Press the MENU button
and enter the menu page.
Use the / buttons to make the appropriate adjustment or setting.
Press the MENU button to leave the menu, and the settings you just made would be
automatically saved.
When button operations are aborted during adjustment, On-Screen Display disappears when the
time set for the OSD Timeout has passed. Also, the MENU button can be used to return previous
menuandturnotheOn-ScreenDisplay.
Any changes are automatically saved in the memory when the On Screen Display
disappears.
TurningothepowershouldbeavoidedwhileusingtheMenu.
Adjustments for Image Position, Clock and Phase are saved for each signal timing. Except for
these adjustments, all other adjustments have only one setting which applies to all signal timings.
NOTE
For example, to correct for vertical position, select Menu item of "Image" by using the /
buttons. Press the MENU button. Then, select "V. Position" by using the / buttons. Press
the MENU button.
Use the / buttons to change the vertical position settings. The vertical position of the overall
display should be changing accordingly while you are doing this.
Press the MENU button on the remote control lastly, it ends, all changes are saved in the
memory.
ENGLISH
14 OPERATING THE MONITOR
[LOCK MODE]
Back Controller Button:
Pressing and holding the MENU and buttons when Menu is not displayed, will lock/unlock the
Back Controller Button Lock function.
ENGLISH
OPERATING THE MONITOR 15
ADJUSTMENT MENU CONTENTS
Adjustment Item Problem / Option Button to Press
Too dark
Too bright
Brightness*2
Contrast Too dull
Too intense
Brightness
Exit Return to Menu.
*1 Available when the Light Sensor Cable is connected.
*2 Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too
bright.
OSD Brightness Ambient Light
Sensor*1
Automatically adjust image brightness to
changing ambient lighting conditions.
Ambient Light Sensor
withOSDoset*1Adjust to minimum brightness according to your application.
Direct
You can skip the Menu items and directly display an adjustment scale by using the following button
operations.
Brightness : Press the button when the Menu is not displayed.
Direct
ENGLISH
16 OPERATING THE MONITOR
You can skip the Menu items and directly display an option setting screen by using the following
button operations.
Signal Select : Press the button when the Menu is not displayed.
Direct
Adjustment Item Problem / Option Button to Press
Signal Select
Signal Select
VGA
DVI
HDMI
Exit Return to Menu.
SelecttheAnalog(VGA)input.
SelecttheDigital(DVI)input.
SelecttheDigital(HDMI)input.
Direct
AV Not available on this model.
S-VIDEO Not available on this model.
YPbPr Not available on this model.
ENGLISH
OPERATING THE MONITOR 17
Adjustment Item Problem / Option Button to Press
Sound
Volume Too soft
Too loud
Return the sound volume to the previous level.
Turnothesoundtemporarily.
Mute
Exit Return to Menu.
ENGLISH
18 OPERATING THE MONITOR
Adjustment Item Problem / Option Button to Press
Color
Cool
Warm
Color Temperature
sRGB
sRGB
NOTE
sRGB is an international standard which denes and unies the dierence of color
appearance between equipment.
Too weak
Too strong
Red
Green
Blue
User
Exit Return to Menu.
Color Adjustment Adjusts color automatically.
ENGLISH
OPERATING THE MONITOR 19
Auto Adjustment *2Adjusts H. Position, V. Position, Clock and Phase automatically.
Adjustment Item Problem / Option Button to Press
Image *1
Clock Too narrow
Too wide
Phase Tocorrectickeringtextorlines
H. Position Too left
Too right
Too low
Too high
V. Position
Return to Menu.
Exit
*1 Only VGA input.
*2 For best results, use the Auto Adjust in conjunction with the adjustment pattern. See page 22 for
SCREEN ADJUSTMENTS.
ENGLISH
20 OPERATING THE MONITOR
Adjustment Item Problem / Option Button to Press
Tools
OSD timeout
You can set the OSD display
duration time between 3 and 27
seconds.
OSD H. Position OSD is too left
OSD is too right
OSD is too low
OSD is too high
OSD V. Position
Reset Factory-preset data is restored.
Sharpness Too soft
Too sharp
Return to Menu.
Exit
OSD Control
LCD Size
Return to Menu.
Exit
Not available on this model.
ENGLISH
OPERATING THE MONITOR 21
Adjustment Item Problem / Option Button to Press
Exit
Exit.
Exit
ENGLISH
22 OPERATING THE MONITOR
SCREEN ADJUSTMENTS
The screen adjustments described in this manual are designed to set image position and minimize
ickerorblurfortheparticularcomputerinuse.
The monitor is designed to provide the best performance at resolution of 1920 × 1080, but can not
provide the best at resolutions of less than 1920 × 1080 because the picture is automatically stretched
totthefullscreen.Itisrecommendedtooperateatresolutionof1920×1080innormaluse.
Displayed text or lines will be blurred or irregular in thickness when the picture is stretched due to
the screen enlargement process.
It is preferable to adjust the image position and frequency with the monitor controls, rather than
the computer software or utilities.
Perform adjustments after a warm-up period of at least thirty minutes.
Additional adjustments may be required after the Auto Adjust depending on the resolution or signal timing.
The Auto Adjust may not work correctly when displaying the picture other than the screen
adjustment pattern. In this case, manual adjustments are required.
There are two ways to adjust the screen. One way is automatic adjustment for Position, Clock and
Phase. The other way is performing each adjustment manually.
Perform the Auto Adjust first when the monitor is connected to a new computer, or resolution is
changed.Ifthescreenhasaickerorblur,orthepicturedoesnottinthedisplayareaafterperforming
the Auto Adjust, manual adjustments are required. Both adjustments should be made by using the
screenadjustmentpattern(Test.bmp)obtainedviatheIIYAMAwebsite(http://www.iiyama.com).
Adjust the image by following the procedure below to get the desired picture.
This manual explains adjustment under Windows® OS.
Display the picture at the optimum resolution.
Enter the Test.bmp (screen adjustment pattern) to wallpaper.
Consult the appropriate documentation for doing this.
Set the display position to center in the wallpaper setting dialogue box. If you use
Microsoft® PLUS! 95/98 cancel the setting of “Stretch desktop wallpaper to t the
screen”.
[Adjustment pattern]
Zebra pattern
Color bar
Picture frame
NOTE
Adjust the image by following the procedure below to get the desired picture when selecting Analog input.
ENGLISH
OPERATING THE MONITOR 23
1) Adjust the H. Position so that the left side of the picture frame will move to the left edge
of the display area.
When the left side of the picture frame moves apart from the left edge of the display
areaduringtheClockadjustment,adjuststeps1)and2).
Another way to make the Clock adjustment is to correct the vertical wavy lines in the
zebra pattern.
ThepicturemayickerduringtheClock,H./V.Positionadjustment.
In case the picture frame is bigger or smaller than the data display area after the
Clock adjustment, repeat steps from .
2) Stretch the right side of the picture frame to the right edge of the display area by
adjusting the Clock.
Adjust the Auto Adjustment.
Adjust the image manually by following procedure below when the screen has a icker or
blur, or the picture does not t in the display area after performing the Auto Adjust.
Adjust the V. Position so that the top and bottom of the picture frame will t to the display
area.
NOTE
ENGLISH
24 OPERATING THE MONITOR
Incasethestrongickerorblursremainonapartofthescreen,repeatsteps and
becausetheClockmaynotbeadjustedcorrectly.Iftheickerorblursstillremain,set
therefreshrateofcomputertolow(60Hz)andrepeatstepsfrom again.
Adjust the H. Position after the Phase adjustment if the horizontal position moves
during the adjustment.
Adjust the Brightness and Color to get the desired picture after you complete the Clock
and Phase adjustments.
Put back your favorite wallpaper.
Adjust the Phase to correct horizontal wavy noise, icker or blur in the zebra pattern.
NOTE
ENGLISH
TROUBLE SHOOTING 25
The screen is not
synchronized.
The Signal Cable is properly connected.
Thesignaltimingofthecomputeriswithinthespecicationofthemonitor.
Thevideooutputlevelofthecomputeriswithinthespecicationofthemonitor.
The picture does
not appear.
The screen
position is not in
the center.
Thesignaltimingofthecomputeriswithinthespecicationofthemonitor.
The screen is too
bright or too dark.
The screen is
shaking.
The video output level of the computer is within the specication of the
monitor.
Thepowervoltageiswithinthespecicationofthemonitor.
Thesignaltimingofthecomputeriswithinthespecicationofthemonitor.
No sound.
Theaudioequipment(computeretc.)isON.
The Audio Cable is properly connected.
The Volume is turned up.
The Mute is OFF.
Theaudiooutputleveloftheaudioequipmentiswithinthespecicationof
the monitor.
The sound is too
loud or too quiet.
Theaudiooutputleveloftheaudioequipmentiswithinthespecicationof
the monitor.
A strange noise is
heard.
The Audio Cable is properly connected.
TROUBLE SHOOTING
Problem Check
If the monitor fails to operate correctly, please follow the steps below for a possible solution.
1. Perform the adjustments described in OPERATING THE MONITOR, depending on the problem
you have. If the monitor does not get a picture, skip to 2.
2.ConsultthefollowingitemsifyoucannotndanappropriateadjustmentiteminOPERATINGTHE
MONITOR or if the problem persists.
3.
If you are experiencing a problem which is not described below or you cannot correct the problem,
discontinue using the monitor and contact your dealer or iiyama service center for further assistance.
ThePowerCableisrmlyseatedinthesocket.
The Power Switch is turned ON.
The AC socket is live. Please check with another piece of equipment.
If the blank screen saver is in active mode, touch the keyboard or the mouse.
Increase the Contrast and/or Brightness.
The computer is ON.
The Signal Cable is properly connected.
Thesignaltimingofthecomputeriswithinthespecicationofthe
display
.
If the
display
is in power management mode, touch the keyboard or the mouse.
The computer is ON.
The Signal Cable is properly connected.
Thesignaltimingofthecomputeriswithinthespecicationofthe
display
.
(Powerindicator
isred.)
(Powerindicator
isgreen.)
(Powerindicator
doesnotlightup.)
ENGLISH
26 Recycling information
For better environment protection please don't dispose your monitor.
Please visit our web site: www.iiyama.com for monitor recycling.
RECYCLING INFORMATION
ENGLISH
APPENDIX 27
APPENDIX
Designandspecicationsaresubjecttochangewithoutpriornotice.
SPECIFICATIONS : ProLite S3820HSB
* Audio equipment are not connected.
NOTE
Size Category 38"
LCD
Panel
Panel technology
MVA
Size Diagonal:37.6"(96.5cm)
Pixel pitch 0.1596mm H × 0.4788mm V
Brightness 1000cd/m2(Typical)
Contrast ratio 4000:1(Typical)
Viewable angle Horizontal:178degrees,Vertical:178degrees(Typical)
Response time 8ms(Typical)
Display Colors Approx.16.7M
Sync Frequency Analog: Horizontal: 30.0-83.0kHz, Vertical: 50-76Hz
Digital: Horizontal: 30.0-83.0kHz, Vertical: 50-76Hz
Maximum Resolution 1920 × 540, 1.0 MegaPixels
Input Connector VGA, DVI, HDMI
Serial Port RS-232C In
Plug & Play VESA DDC2BTM
Input Sync Signal Separate sync: TTL, Positive or Negative
Input Video Signal
Analog:0.7Vp-p(Standard),75Ω, Positive
Digital:DVI(DigitalVisualInterfaceStandardRev.1.0)compliance
Digital: HDMI
Input Audio Connector ø3.5mmminijack(Stereo)
Input Audio Signal 0.5Vrms maximum
Speakers 5W×2(Stereospeakers)
Light Sensor Connector mini jack
Maximum Screen Size 919.3mm W × 258.5mm H / 36.2" W × 10.2" H
Power Source 12VDC 5.0A
ACAdapter(accessory) Input: 100-240VAC, 50-60Hz
Power Consumption* 42.5W typical
EnergyEciencyClass:B
Dimensions / Net Weight 962.5×305.0×54.0mm/37.9×12.0×2.1"(W×H×D)
8.8kg / 19.4lbs
Environmental Considerations
Operating:
Storage:
Temperature
Humidity
Temperature
Humidity
0 to 50°C / 32 to 122°F
85%(Nocondensation)
-20 to 60°C / 4 to 140°F
85%(Nocondensation)
Approvals CB, CE, CU
ENGLISH
28 APPENDIX
DIMENSIONS : ProLite S3820HSB
924.5mm/36.4”
962.5mm/37.9”
148.0mm/5.8”
263.5mm/10.4”
305.0mm/12.0”
524.0mm/20.6”
18.0mm/0.7”
44.0mm/1.7”
54.0mm/2.1”
194.5mm/7.7”
55.5mm/2.2”
400.0mm/15.7”
100.0mm/3.9”
4xM6 SCREW HOLE
(VESA MOUNT)
COMPLIANT TIMING
M229A21
Video Mode Horizontal
Frequency
Vertical
Frequency Dot Clock
640 × 480 31.469kHz 59.940Hz 25.175MHz
800 × 600 37.879kHz 60.317Hz 40.000MHz
1024 × 768 48.363kHz 60.004Hz 65.000MHz
1280 × 1024 63.981kHz 60.020Hz 108.000MHz
1680 × 1050 65.290kHz 60.000Hz 146.250MHz
1920 × 1080 66.590kHz 59.930Hz 138.500MHz