iiyama TE9804MIS-B1AG User Manual
Displayed below is the user manual for TE9804MIS-B1AG by iiyama which is a product in the Interactive Whiteboards category. This manual has pages.
Related Manuals
ENGLISH
Thank you very much for choosing the iiyama
LCD monitor.
We recommend that you take a few minutes
to read this comprehensive manual carefully
before installing and switching on the monitor.
Please keep this manual in a safe place for
your future reference.
USER MANUAL
ENGLISH
ENGLISH
Wereservetherighttochangespecicationswithoutnotice.
All trademarks used in this user manual are the property of their respective owners.
We recommend recycling of used product. Please contact your dealer or iiyama
service center. Recycle information is obtained via the Internet, using the
address: http://www.iiyama.com
YoucanaccesstheWebpageofdierentcountriesfromthere.
CE MARKING DECLARATION OF CONFORMITY
This LCD monitor complies with the requirements of the EC/EU Directive 2014/30/EU “EMC
Directive”, 2014/35/EU “Low Voltage Directive”, 2009/125/EC “ErP Directive” and 2011/65/EU
“RoHS Directive”.
Warning
This is a class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
IIYAMA CORPORATION: Wijkermeerstraat 8, 2131 HA Hoofddorp, The Netherlands
Model No. : PL9804U
ENGLISH
TABLE OF CONTENTS
FOR YOUR SAFETY ............................................................................ 1
SAFETY PRECAUTIONS................................................................1
SPECIAL NOTES ON LCD MONITORS .........................................3
CUSTOMER SERVICE ...................................................................5
CLEANING ......................................................................................5
BEFORE YOU OPERATE THE MONITOR ..........................................6
FEATURES......................................................................................6
CHECKING THE CONTENTS OF THE PACKAGE ........................6
UNPACKING ...................................................................................7
SPECIAL NOTES ON THE TOUCH PANEL ...................................7
INSTALLATION ...............................................................................8
CONTROLS AND CONNECTORS : MONITOR ............................10
CONTROLS : REMOTE CONTROL ..............................................12
PREPARING THE REMOTE CONTROL.......................................13
BASIC OPERATION ......................................................................15
CONNECTING YOUR MONITOR .................................................18
COMPUTER SETTING .................................................................22
OPERATING THE MONITOR .............................................................24
ADJUSTMENT MENU CONTENTS ..............................................26
SCREEN ADJUSTMENTS ............................................................44
STANDBY FEATURE ....................................................................47
TROUBLE SHOOTING ......................................................................48
RECYCLING INFORMATION .............................................................49
APPENDIX ........................................................................................50
SPECIFICATIONS : ProLite TE9804MIS ......................................50
DIMENSIONS ................................................................................ 51
COMPLIANT TIMING ....................................................................52
ENGLISH
FOR YOUR SAFETY 1
FOR YOUR SAFETY
WARNING
STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE
If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the
monitor and contact your dealer or iiyama service center immediately. Further use may be
dangerousandcancausereorelectricshock.
NEVER REMOVE THE CABINET
High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of
reorelectricshock.
DO NOT PUT ANY OBJECT INTO THE MONITOR
Do not put any solid objects or liquids such as water into the monitor. In case of an accident, unplug
your monitor immediately and contact your dealer or iiyama service center. Using the monitor with
anyobjectinsidemaycausere,electricshockordamage.
INSTALL THE MONITOR ON A FLAT, STABLE SURFACE
The monitor may cause an injury if it falls or is dropped.
DO NOT USE THE MONITOR NEAR WATER
Donotusewherewatermaybesplashedorspiltontothemonitorasitmaycausereorelectric
shock.
OPERATE UNDER THE SPECIFIED POWER SUPPLY
Besuretooperatethemonitoronlywiththespeciedpowersupply.Useofanincorrectvoltagewill
causemalfunctionandmaycausereorelectricshock.
PROTECT THE CABLES
Do not pull or bend the power cable and signal cable. Do not place the monitor or any other heavy
objectsonthecables.Ifdamaged,thecablesmaycausereorelectricshock.
ADVERSE WEATHER CONDITIONS
It is advisable not to operate the monitor during a heavy thunder storm as the continual breaks in
power may cause malfunction. It is also advised not to touch the plug in these circumstances as it
may cause electric shock.
SAFETY PRECAUTIONS
ENGLISH
2 FOR YOUR SAFETY
CAUTION
INSTALLATION LOCATION
Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or
smokyareasasitmaycausere,electricshockordamage.Youshouldalsoavoidareaswherethe
sun shines directly on the monitor.
DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION
The monitor may topple and cause injury if not suitably located. Please also ensure that you do not
place any heavy objects on the monitor, and that all cables are routed such that children may not
pull the cables and possibly cause injury.
MAINTAIN GOOD VENTILATION
Ventilation slots are provided to keep the monitor from overheating. Covering the slots may cause
re.Toallowadequateaircirculation,placethemonitoratleast10cm(or4inches)fromanywalls.
Operating the monitor on its back, side, upside down or on a carpet or any other soft material may
also cause damage.
DISCONNECT THE CABLES WHEN YOU MOVE THE MONITOR
Whenyoumovethemonitor,turnothepowerswitch,unplugthemonitorandbesurethesignal
cableisdisconnected.Ifyoudonotdisconnectthem,itmaycausereorelectricshock.
UNPLUG THE MONITOR
If the monitor is not in use for a long period of time it is recommended that it is left unplugged to
avoid accidents.
HOLD THE PLUG WHEN DISCONNECTING
To disconnect the power cable or signal cable, always pull it by the plug. Never pull on the cable
itselfasthismaycausereorelectricshock.
DO NOT TOUCH THE PLUG WITH WET HANDS
Pulling or inserting the plug with wet hands may cause electric shock.
WHEN YOU INSTALL THE MONITOR ON YOUR COMPUTER
Be sure the computer is strong enough to hold the weight of the monitor, otherwise, you may
damage your computer.
ERGONOMIC RECOMMENDATIONS
To eliminate eye fatigue, do not operate the monitor against a bright background or in a dark room.
Foroptimalviewingcomfort,themonitorshouldbejustbeloweyeleveland40-60cm(16-24inches)
away from your eyes. When using the monitor over a prolonged time, a ten minute break every hour
is recommended as looking at the screen continuously can cause eye strain.
OTHERS
ENGLISH
FOR YOUR SAFETY 3
The following symptoms are normal with LCD monitors and do not indicate a problem.
NOTE -WhenyourstturnontheLCDmonitor,thepicturemaynottinthedisplayarea
because of the type of computer that is used. In this case, adjust the picture position to
the correct position.
-Youmayndslightlyunevenbrightnessonthescreendependingonthedesktop
pattern you use.
- Due to the nature of the LCD screen, an afterimage of the previous screen may remain
after switching the image, when the same image is displayed for hours. In this case, the
screenisrecoveredslowlybychangingtheimageorturningothePowerSwitchfor
hours.
SPECIAL NOTES ON LCD MONITORS
This LCD cannot be used outdoors.
This LCD cannot be used with the screen facing upwards.
If you use a cable longer than the supplied one, the picture quality is not guaranteed. Touch
function can be disrupted if the USB cable length exceeds 3m.
ENGLISH
4 FOR YOUR SAFETY
USAGE CONFIRMATION
This product is designed for optimum usage at 24 hours per day.
The display is compatible for usage in Landscape applications.
IMAGE PERSISTENCE / IMAGE STICKING
Please be aware that all LCD screens can experience Image Persistence or Image Sticking. This
occurs when a residual image remains visible on a screen when static images are displayed for long
periods of time. LCD Image Persistence is not permanent but constant images being displayed for a
long period of time should be avoided.
To counteract Image Persistence, turn off the monitor for as long as the previous image was
displayed, so if an image was on the monitor for 1 hour and there is evidence of a residual or “ghost”
image,youshouldturnothemonitorfor1hourinordertocleartheresidualimage.
For all LFD products, iiyama recommends displaying moving images and utilising a moving screen
saveratregularintervalswheneverthescreenisidle.Youcouldalsoturnothemonitorwhennot
in use to assist the prevention.
OtherwaystoreducetheriskofImagePersistencewillbetoutilisetheFAN-onfunction(if
available),LowBacklightandLowBrightnesssettings.
FOR EXTENDED USE AS A PUBLIC DISPLAY
Image Sticking on LCD Panel
When a static image is displayed for hours, an electric charge trace remains near the electrode
insidetheLCDproducinga“ghost”image.(ImagePersistence).
Image Persistence is not a permanent feature.
Recommendations
To prevent Image Sticking and promote longer life expectancy of display, we recommend the
following:
1. Avoid static images displayed for long periods – change static images on continuous loop.
2.Turnomonitorwhennotinuse,eitherbyremotecontroloruseStandbyorSchedulefunctions.
3. Check the Monitor Menu Settings for "Pixel Shift" etc. and activate it when available. This will
reducetheImageStickingEect.
4.Whenmonitorisinstalledinhighambienttemperatureenvironment(s)orinanenclosedposition,
utilise the Cooling Fan, Screen Saver and Low Brightness functions.
5. Suitable ventilation for any monitor is an expectation of any installation – climate control systems
may need to be employed.
6. We strongly recommend utilisation of active cooling with fans for long operation times or high
ambient temperature environments.
ENGLISH
FOR YOUR SAFETY 5
NOTE
If you have to return your unit for service and the original packaging has been
discarded, please contact your dealer or iiyama service center for advice or
replacement packaging.
WARNING
If you drop any materials or liquids such as water into the monitor when cleaning,
unplug the power cable immediately and contact your dealer or iiyama service center.
CAUTION
Forsafety reasons,turno thepowerswitch andunplugthe monitorbeforeyou
clean it.
NOTE
To protect the LCD panel, do not scratch or rub the screen with a hard object.
Never use any of the following strong solvents. These will damage the cabinet and
the LCD screen.
Touching the cabinet with any product made from rubber or plastic for a long time
may cause degeneration or loss of paint on the cabinet.
Thinner Benzine Abrasive cleaner
Spray-type cleaner Wax Acid or Alkaline solvent
CABINET Stains can be removed with a cloth lightly moistened with a mild detergent solvent.
Then wipe the cabinet with a soft dry cloth.
LCD
SCREEN
Periodic cleaning with a soft dry cloth is recommended.
Don't use tissue paper etc. because these will damage the LCD screen.
CUSTOMER SERVICE
CLEANING
ENGLISH
6 BEFORE YOU OPERATE THE MONITOR
The following accessories are included in your package. Check to see if they are enclosed with
the monitor. If anything is missing or damaged, please contact your local iiyama dealer or regional
iiyamaoce.
* The rating of the Power Cable enclosed in 120V area is 10A/125V. If you are using
a power supply higher than this rating, then a power cable with a rating of 10A/
250V must be used. However, all guarantees and warranties are void for any
problems or damage caused by a power cable not supplied by iiyama.
An approved power cable greater or equal to H05VVF, 3G, 0.75mm2 must be
used.
Power Cable*
HDMI Cable Touch USB Cable
Remote Control Battery(2pcs) TouchPen(Dualhead:4pcs)
Cableties(Forcablemanagement,6pcs) USBSticker(6pcs)
Safety Guide Quick Start Guide
BEFORE YOU OPERATE THE MONITOR
CHECKING THE CONTENTS OF THE PACKAGE
CAUTION
FEATURES
Supports Resolutions up to 3840 × 2160
High Contrast 1200:1 (Typical: without glass) / Brightness 350cd/m2 (Typical:
without glass)
Digital Character Smoothing
Automatic Set-up
USB Type-C / RJ45 Connectors
USB Power Delivery supports up to 65W
2 × 16W (Typical) Stereo Speakers
Standby Feature (VESA DPMS Compliant)
VESA Mounting Standard (800mm×600mm) Compliant
Glass with AG coating
ENGLISH
BEFORE YOU OPERATE THE MONITOR 7
UNPACKING
CAUTION
Moving the monitor requires at least two people. If not, it may drop and could result in a serious
injury.
SPECIAL NOTES ON THE TOUCH PANEL
Permanent damage can occur if Sharp Edged, Pointed or Metal items are used to activate Touch.
This could invalidate any remaining warranty.
Werecommendyouuseaplasticstylus(tip ø3mm orover)ornger.
CAUTION
ENGLISH
8 BEFORE YOU OPERATE THE MONITOR
INSTALLATION
CAUTION
Follow the manual instructions for the type of mount you have selected. Refer all servicing to
qualiedservicepersonnel.
Moving the monitor requires at least two people.
Before installation, please make sure the wall is strong enough to hold the necessary weight of
the display and the mount.
[WALL MOUNTING]
When using the wall mounting, consideration of thickness of the mounting stage needs to be taken.
TightentheM8Screws(4pcs)withwasherwhich“L”lengthis25mmtofastenthemonitor.Using
a screw longer than this may cause electric shock or damage because it may contact with the
electrical parts inside the monitor.
CAUTION
Screw
Chassis
Mounting Stage
L
ENGLISH
BEFORE YOU OPERATE THE MONITOR 9
[INSTALLATION NOTE]
The touch kit of this monitor is an optical device that utilizes infrared light source and sensitive
sensors for touch detection.
Notice the incident light that contains large quantities of infrared light may affect touch screen
operation and performance.
Please install it with care as follows to ensure reliable touch performance.
Intense light / Specular light / Focus spotlight / Wide spread light / Direct sunlight / Indirect sunlight
from the window and/or the glass door. / Not install the touch monitor right under the light source.
Direct
Sunlight
Windows
Light
source
Light source Light source
Front Front
Side Side
[ROTATING THE DISPLAY]
A
A
Not Available
It is designed to be compatible in landscape mode.
A
Landscape
Available
Power Indicator
A
ENGLISH
10 BEFORE YOU OPERATE THE MONITOR
CONTROLS AND CONNECTORS : MONITOR
<Front>
Power Button
Power O
Pressing and holding the Power Button on the front
for 3-5 seconds.
Power Indicator
Blue Normal Operation
Red
Standby Mode
When the power indicator light is lighting red, the
display is in Power Save Mode. To turn the screen
back on, you can press the power button on the front
or the remote control.
Red & Blue
ashingslow
TheScreenOfunctionisactive.Toturnthescreen
back on, you can touch the screen or any button on
the remote control.
Red & Blue
ashingfast Going to the Standby Mode or system is updating.
Remote Sensor
Light Sensor
USBConnector(3.0) USB3.0(5V,900mA)
ENGLISH
BEFORE YOU OPERATE THE MONITOR 11
<Back>
Option PC module slot
HDMIConnector(HDMIOUT) HDMI
USBConnector(3.0) USB3.0(5V,900mA)
TouchUSBConnector(TOUCH1) USB(forHDMI1/HDMI2)
HDMIConnector(HDMIIN1) HDMI
HDMIConnector(HDMIIN2) HDMI
Option WiFi/BT module slot
HDMIConnector(HDMIIN3) HDMI
TouchUSBConnector(TOUCH2) USB(forHDMI3/VGA)
USB-CConnector(USB-C3.1PD65W) USB-C3.1(5V,3A/9V,3A/12V,3A/20V,3.25A)
SPDIFConnector(SPDIF) SPDIF Output
USBConnector(2.0) USB2.0(f
or software update
)
VGAConnector(
VGA) VGA
AudioConnector(AUDIOIN) Mini Jack
LAN(RJ45)Connector(LAN) RJ45(In/Outautoswitching)
RS232CConnector(RS232) RS232C 9pin
HeadphoneConnector(AUDIOOUT) Mini Jack
ACConnector( :Alternatingcurrent)
Main Power Switch (On)/ (O)
Speakers
Handles
ENGLISH
12 BEFORE YOU OPERATE THE MONITOR
Turn the monitor ON and OFF.
Number(1-9)/
Other /
Function(F1-
F12)
Under iiWare: 0-9 numeric input
Under Windows: 0-9 numeric input,
Start/Space/ALT+Tab/ALT+F4/F1-12
for Keyboard function
Display Provide source and resolution
information.
Home Android system main screen button.
Input Select the source.
Green Lock and unlock Buttons function.
Red Lock and unlock Buttons and Touch
function.
ScreenO TurnthebacklightOnandO.
Navigate through submenus and
settings.
: Up Button
: Down Button
: Left Button
: Right Button
Enter Conrmyourselectionorsave
changes.
Quickly start “Writing Software”.
PgUp / PgDn
WhenselectFile:Therst/Last
When Internet browser: Scroll Up /
Scroll Down
Not available on this model.
Turnonorothemutefunction
when the Menu is not displayed.
MENU
Display the “Screen Setting“ menu
when the Android system is not
displayed.
Yellow Lock and unlock Touch function.
Blue Freeze the picture.
Backspace
Back Return to a previous menu or closes
the OSD Menu.
VOL+ / VOL- VOL+: Increase the sound volume.
VOL-: Decrease the sound volume.
CONTROLS : REMOTE CONTROL
ENGLISH
BEFORE YOU OPERATE THE MONITOR 13
To use the remote control, insert the two dry batteries.
PREPARING THE REMOTE CONTROL
Open back cover of battery component on the back of remote control.
AlignandinserttwoAAAbatteriesaccordingtotheirplusandminusports(asindicatedinthe
remotecontrol).
After battery is installed, close the back cover of battery components, and make the following clip
buckled to the bottom.
Battery x 2
CAUTION
DonotuseanyotherbatteriesotherthanthosespeciedinthismanualfortheRemoteControl.
Do not insert old and new batteries together in the Remote Control.
Make sure that the terminals match the "+" and "-" indications in the battery compartment.
Remove the dead batteries immediately to prevent them from liquid leaking into the battery
compartment.
Burstbatteriesortheelectrolytefromthesebatteriesmaycausestains,reorinjury.
ENGLISH
14 BEFORE YOU OPERATE THE MONITOR
NOTE Refer to the above instructions when taking out the batteries.
Replace with new batteries when the Remote Control does not work close to the monitor.
Use AAA dry batteries. Risk of explosion if battery is replaced by an incorrect type.
Operate the Remote Control by pointing it toward the Remote Sensor on the monitor.
Other manufacturers remote control will not work with this monitor. Use the provided
Remote Control ONLY.
Usedbatteriesneededtofollowthecityruletobediscarded.(suggestion:todisposeof
usedbatteriespleasefollowcorrectpolicyasperyourcouncilregulations)
Batteriesshallnotbeexposedtoexcessiveheatsuchassunshine,reorthelike.
If you do not intend to use the remote control for a long period, remove the batteries.
ENGLISH
BEFORE YOU OPERATE THE MONITOR 15
BASIC OPERATION
Turning the monitor ON
The monitor is turned On and the Power Indicator turns to Blue when you press the Power Button
onthemonitorortheRemoteControl.ThemonitoristurnedOandthePowerIndicatorturnsto
Red when you press the Power Button on the monitor or the Remote Control. Press again to turn
On the monitor.
NOTE
Even when using the standby mode or turning OFF the Power Switch, the monitor will consume
a small amount of electricity. Turn OFF the Power Switch or disconnect the Power Cable from the
power supply whenever the monitor is not in use or during the night, to avoid unnecessary power
consumption.
[Remote Control]
Display the adjustment menu page
The menu page appears on the screen when you press the Menu Button on the Remote
Control.
The menu page disappears when you press the Back Button on the Remote Control.
[Monitor]
[Remote Control]
ENGLISH
16 BEFORE YOU OPERATE THE MONITOR
Move the cursor horizontally
Select menu or setting, or perform the adjustment by pressing the / Button on the remote
control while the menu page is displayed on the screen.
Move the cursor vertically
Select adjustment by pressing the / Button on the remote control while the menu page is
displayed on the screen.
[Remote Control]
[Remote Control]
ENGLISH
BEFORE YOU OPERATE THE MONITOR 17
Adjust the volume of sound
Press the VOL- / VOL+ Button on the remote control to adjust the volume of sound when the
menu page is not displayed on the screen.
Switch the input signal
The Input setting menu appears on the screen when you press the Input Button on the remote
control.
[Remote Control]
[Remote Control]
ENGLISH
18 BEFORE YOU OPERATE THE MONITOR
CONNECTING YOUR MONITOR
Ensurethatboththecomputerandthemonitorareswitchedo.
Connect the computer to the monitor with the signal cable.
Connect the computer to the monitor with the Touch USB Cable.
Connect the computer to the monitor with the USB Type-C Cable when viewing images on your
monitor through the USB Type-C Connector or when using the monitor’s USB hub function.*
ConnectthePowerCabletothemonitorrstandthentothepowersource.
Turnonyourmonitor(MainPowerSwitchandPowerButton)andcomputer.
*
When charging connected device via USB Type-C Connector, check if the device is equipped
with aUSBType-CConnectorthatsupportschargingfunctionviaUSBPD(=PowerDelivery).
The connected device can be charged via USB Type-C Connector even when the monitor is in
standby mode.
The USB power delivery is up to 65W. If the connected device required more than 65W for
operationorforbootup(whenthebatteryisdrained),usetheoriginalpoweradapterthatcame
with the device.
IfaseparatelypurchasedUSBType-CCableisused,makesurethecableiscertiedbyUSB-IF
and is full-featured with power delivery and video / audio / data transfer functions.
USB C to A cable is not included with the monitor. If you use a USB C to A cable, please note
that you can only transfer data.
Compatibilitywithallconnecteddevicesisnotguaranteedduetodierentuserenvironments.
Make sure that the building installation has a circuit breaker of 120/240V, 20A
(maximum).
The signal cables used for connecting the computer and monitor may vary with the
type of computer used. An incorrect connection may cause serious damage to both
the monitor and the computer. The cable supplied with the monitor is for a standard
connector. If a special cable is required please contact your local iiyama dealer or
regionaliiyamaoce.
MakesureyoutightenthengerscrewsateachendoftheSignalCable.
The touch function is ready for use about 5 seconds after connecting the USB cable and
canbeoperatedwithapen,ngeroranyotherpointer.
The Class I pluggable equipment Type A must be connected to protective earth.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
Excessive sound pressure from ear-/headphones can cause hearing damage/hearing loss.
NOTE
ENGLISH
BEFORE YOU OPERATE THE MONITOR 19
[Example of Connection]
<Back>
* VGA cable is not supplied with the monitor. If you use low quality VGA cable, it may cause a result
of electro-magnetic interference. Please contact the iiyama Support Centre in your country if you
wish to connect the monitor via the VGA input.
HDMI Cable (Accessory)
AV Equipment etc.
Desktop Computer
USB-C Cable (Not included)
Laptop Computer
Power Cable (Accessory)
LAN(RJ45) Cable
(Not included) Router
LAN(RJ45) Cable
(Not included)
Audio Cable (Not included)
VGA Cable (Not included)*
Touch USB Cable (Accessory)
ENGLISH
20 BEFORE YOU OPERATE THE MONITOR
[ Connection example with the peripheral device ]
CAUTION
Turn o the power switch and unplug the monitor and peripherals before connection to avoid an
electric shock or a damage.
NOTE
Refer to the user manual of peripherals at the same time.
Ensure you have the necessary cables as required.
ENGLISH
BEFORE YOU OPERATE THE MONITOR 21
[ About the HDMI out ]
[VGAIN]
MONITOR1
[VGA] [HDMIOUT] [HDMIIN]
MONITOR2
Example of Digital video connection
Connection conditions
When 2 monitors are connected:
VGAinput(operatingat1920×1080resolution):MONITOR1,2(1920×1080)
USB-Cinput(operatingat3840×2160resolution):MONITOR1,2(3840×2160)
For the advance setting support HDMI in signal.
Input+2580(DebugMenu:HDMIOUTEnable)
NOTE
VGA
[USB-CIN]
MONITOR1
[USB-C] [HDMIOUT] [HDMIIN]
MONITOR2
USB-C
[HDMIIN]
MONITOR1
[HDMIOUT] [HDMIOUT] [HDMIIN]
MONITOR2
HDMI*
* Not suppoted, enable in factory menu.
ENGLISH
22 BEFORE YOU OPERATE THE MONITOR
Procedure for turning ON the Power Switch
TurnONthemonitorrst,andthenthecomputer.
Signal Timing
Change to the desired signal timing listed on page 52: COMPLIANT TIMING.
Windows XP/Vista/7/8/8.1/10 Plug & Play
The iiyama LCD monitor complies with DDC2B of VESA standard. The Plug & Play function runs
on Windows /XP/Vista/7/8/8.1/10 by connecting the monitor to DDC2B compliant computer with
the Signal Cable supplied.
For installation on Windows XP: The monitor Information File for iiyama monitors may be
necessary for your computer and obtained via the Internet, using the address:
http://www.iiyama.com
For additional information on how to download the driver for your touch screen monitor,
please access the internet site noted above.
Monitor Drivers are not required in most cases for Macintosh or Unix operating
systems.Forfurtherinformation,pleasecontactyourcomputerdealerrstforadvice.
COMPUTER SETTING
NOTE
ENGLISH
BEFORE YOU OPERATE THE MONITOR 23
MULTI-TOUCH :
ThismonitorcomplieswithDDC2BofVESAstandard.(Plug&playcompliant)
The MULTI-TOUCH function runs on Windows7/8/8.1/10 by connecting the monitor to DDC2B
compliant computer with the USB cable supplied.
TOUCH support operation system :
MicrosoftWindows2000(64bitand32bit)
MicrosoftWindowsXP(64bitand32bit)
MicrosoftWindowsVista(64bitand32bit)
MicrosoftWindows7(64bitand32bit)
MicrosoftWindows8/8.1/10(64bitand32bit)
Mac OS X V10.15 & higher HID for single touch only
Linux 3.0 & higher need patch for multi-touch
3.5 & higher HID for multi-touch
Not support Windows earlier versions.
Windows
7*5,8/8.1*6,10*6,7,8 Windows7*4Vista XP 2000 Mac OSX Linux
Default mouse*1
Touch digitizer*2
Windows gestures*3
*1 Defaultmouse(click,drag,double-clickandright-click)
*2 Touchdigitizer(click,drag/selection,double-click,right-click,ickandvisualfeedback)
*3 Digitizer with Windows7/8/8.1/10 multi-touch gestures
*4 Windows 7 - Starter and Home Basic version
*5 Windows 7 - Home Premium, Professional, Enterprise and Ultimate versions
*6 Windows 8/8.1/10 need non-OEM version for multi-touch support
*7 Windows10 - Home, Pro, Enterprise, Education, IoT Core
Not supported for Mobile and Mobile Enterprise.
*8 Windows10 - Touch do no support for “touchpad gestures”. Touchpad gesture is for touchpad on
notebook.
ENGLISH
24 OPERATING THE MONITOR
OPERATING THE MONITOR
To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT
TIMING shown on page 52. You are also able to adjust the picture by following the button operation
shown below. For more detailed adjustments, see page 44 for SCREEN ADJUSTMENTS.
Take middle point position on the buttom of display screen as starting point, use the
touch pen to drag towards screen center position to call up source menu as shown
below. Or press Input Button on the remote control. Click the icon at the top
right of the screen.
Start the On Screen Display feature. "General setting" is displayed. Then, press
the menu button on the remote control or click on General setting menu with
touch pen. There are additional Menu items which can be switched by using the /
Buttons on the remote control or with the touch pen.
Select the Menu item of the adjustment you want to make. Use the / Buttons on
the remote control or with the touch pen to highlight the desired adjustment item.
Then, press the Enter button on the remote control.
Use the / Buttons on the remote control or with the touch pen to make the
appropriate adjustment or setting.
Press the Back Button on the remote control or click blank area outside menu with
the touch pen to exit menu.
For example, to correct for vertical position, select Menu item of "Adjust setting". Select "V
Position" by using the / Buttons on the remote control or with the touch pen.
Use the /Buttons on the remote control or with the touch pen to change the vertical
position settings. The vertical position of the overall display should be changing accordingly
while you are doing this.
Press the Back Button on the remote control or click blank area outside menu with the touch
pen, it ends, all changes are saved in the memory.
Slot-PC iiWare HDMI1 HDMI2
HDMI3 Type-C VGA
General setting
Screen center
H Position
AdjustDisplayScreenAudio
V Position
Clock
Phase
AUTO
* "Adjust setting" is only
available for VGA input.
ENGLISH
OPERATING THE MONITOR 25
The Back Button on the remote control can be used to return previous menu item.
Any changes are automatically saved in the memory when the On Screen Display
disappears.
TurningothepowershouldbeavoidedwhileusingtheMenu.
Adjustments for Image Position, Clock and Phase are saved for each signal timing. Except for
these adjustments, all other adjustments have only one setting which applies to all signal timings.
NOTE
Direct
Freeze Function:
Press the Blue button when Menu is not displayed.
Repeat successively to activate/deactivate the function.
Backlight Function:
PresstheScreenObuttonwhenMenuisnotdisplayed.
RepeatsuccessivelytoOn/Othefunction.
Input Function:
Press the Input Button when Menu is not displayed.
Volume Function:
Press the VOL+/VOL- Buttons when Menu is not displayed.
Mute Function:
Press the Button when Menu is not displayed.
RepeatsuccessivelytoOn/Othefunction.
Kiosk Mode Function:
Disable touch functions, buttons, Menu etc.
Turno"iiWareEnable"inDebugmenu(Input+2580)
* Available for Remote Control only.
[LOCK MODE]
Front Power Button:
Press the Green Button when Menu is not displayed, will lock/unlock the Front Power Button.
Touch function:
Press the Yellow Button when Menu is not displayed, will lock/unlock the Touch function.
Front Power Button & Touch function:
Press the Red Button when Menu is not displayed, will lock/unlock the Front Power Button and
Touch function.
* Available for Remote Control only.
ENGLISH
26 OPERATING THE MONITOR
ADJUSTMENT MENU CONTENTS
Adjustment Item Problem / Option Button to Press
General setting
Input *1
Slot-PC*2Select the Slot PC input.
HDMI1 Select the HDMI1 input.
HDMI2 Select the HDMI2 input.
HDMI3 Select the HDMI3 input.
Backlight Brightness of backlight is reduced.
Direct
Direct
Volume Too soft
Too loud
Direct
*1 The switching of the signal input take a few seconds.
*2 Available when Slot-PC is installed only.
You can also access the Menu by clicking on the desktop or on the navigation toolbar.
iiWare Select the iiWare input.
Type-C Select the Type-C input.
Slot-PC iiWare HDMI1 HDMI2
HDMI3 Type-C VGA
General setting
VGA Select the VGA input.
ENGLISH
OPERATING THE MONITOR 27
Adjustment Item Problem / Option Button to Press
Treble Too weak
Too strong
Meeting Sound quality suitable for the conference.
Audio setting
Volume
Sound Mode Class Sound quality suitable for the classroom.
Bass Too weak
Too strong
Balance
Standard
Custom
Mute Return the sound volume to the previous level.
Turnothesound.
Custom sound quality.
Standard
Left side speaker louder
Right side speaker louder
Too soft
Too loud
Direct
Direct
Volume
AdjustDisplayScreenAudio
Bass BalanceTreble
Mute
CustomClassMeetingStandard
ENGLISH
28 OPERATING THE MONITOR
Aspect ratio
PTP * Display the picture point to point.
16:9
4:3 Displays all picture in 4:3 aspect ratio.
Displays all picture in 16:9 aspect ratio.
Adjustment Item Problem / Option Button to Press
Screen setting
* Point To Point, to optimize touch performance when 3840 ×2160 input. (not available under
Android or not 3840 ×2160inputtiming)
Pixel Shift
Pixel Shiftisturnedo.
The screen image will move around slightly every 2
minutes.
ECO
AdjustDisplayScreenAudio
Auto Light
Pixel Shift
Eye Comfort
ECR
Eye Comfortisturnedo.
Auto Lightisturnedo.
ECOisturnedo.
Eye Comfort
Auto Light
ECO
Blue light is reduced.
The image brightness can be automatically adjusted
according to the ambient light.
Brightness of back-light is reduced.
ECR Enhanced Contrast Ratio
ECRisturnedo.
ENGLISH
OPERATING THE MONITOR 29
Adjustment Item Problem / Option Button to Press
Display setting
Color Temp
Standard
Cold
Warm
Too dark
Too bright
Brightness*1
Contrast Too dull
Too intense
Sharpness
*1
Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too bright.
*2 Display Mode is disabled when iiWare input.
Hue
Custom
Standard
Displays a picture on a screen set by Image
Settings adjustments.
For general windows environment and
monitor default setting.
Display Mode *2Bright
Soft
Enlarge brightness and vivid.
Reduce brightness and soften.
Sharpness
AdjustDisplayScreenAudio
HueBrightness Contrast
CustomSoftBrightStandard WarmColdStandard
Blue Light Reducer Blue light is reduced. (Custom)
Cool color
Warm color
Normal color
Not available for this model.
Not available for this model.
ENGLISH
30 OPERATING THE MONITOR
Adjustment Item Problem / Option Button to Press
Adjust setting *1
Auto *2Adjust H/V Position, Clock and Phase automatically.
Clock Too narrow
Too wide
Phase Tocorrectickeringtextorlines
H Position Too far to the left
Too far to the right
Too low
V Position Too high
*1 Only VGA input.
*2 For best results, use the Auto Adjust in conjunction with the adjustment pattern. See page 44 for
SCREEN ADJUSTMENTS.
H Position
AdjustDisplayScreenAudio
V Position
Clock
Phase
AUTO
ENGLISH
OPERATING THE MONITOR 31
[Debug Menu]
Initial Touch Panel
The default settings will be restored.
Unknown sources: On / O
Enables / disables Unknown sources.
iiWare Enable: On / O
Enables / disables Kiosk mode.
HDMI OUT Enable: On / O
Enables / disables "HDMI OUT Enable" when input source is HDMI.
Exit
* Available for Remote Control only. Input + 2580
ENGLISH
32 OPERATING THE MONITOR
[Application]
Settings
Click on the navigation toolbar with the touch pen. Then, click with the touch pen.
Status bar
: Click to display the General settings.
: Click to display the Brightness.
: Click to display the Volume.
: Click to display the Ethernet settings.
:DisplayedwhenUSBashdriveisconnected.ClicktoaccessyourUSBashdriveinthe
Finder application.
: Click to display the Hotspot settings.
: Displayed when WiFi module is inserted. Click to display the WiFi Settings.
01:41(Clock):ClickontheclockdisplaytodisplaytheDate&TimeofSettings.
xxxxxx :
When connecting a LAN or Option WiFi module, the password for a notebook or a smartphone, etc.
toconnecttoScreenSharePro,isdisplayedonthescreen.(Automaticallygenerated)
ENGLISH
OPERATING THE MONITOR 33
Adjustment Item Problem / Option Button to Press
[ Settings ]
Startup channel
Standbyafterstartup(blackscreen):Turnothebacklight.
Last shutdown channel / Slot-PC*3 / iiWare /
HDMI1 / HDMI2 / HDMI3 / Type-C / VGA
Wireless &
network
Input & Output
Set the wired network.
Network:On/O,MacAdress,IPadress,Defaultgateway,
Netmask, DNS, Proxy
Application Application management
Show System, Reset App Preferences
Language
&
Keyboard
Set display language, keyboard and input method.
Language:Catala/Čeština/Deutsch/English/Español/
Français/Italiano/Nederlands/Polski/Русский
NOTE
Ethernet
Personal
WiFi*1,2
Bluetooth*1
SettheWiFifunctionOn/OandpairingtoWiFidevice.
SettheBluetoothfunctionOn/OandpairingtoBluetoothdevice.
Sound TouchSounds:On/O
Sound Output Settings : Speaker / Headphone / Line Out
PresstheScreenObuttonontheremotecontrolor
touch the screen to return to the screen.
Hotspot*1,2 Set the Hotspot function.
Network:On/O,SSID,Password,DHCPsettings
VPN
Set the VPN.
Wallpaper
Set the
Wallpaper
.(Stills,Dynamic)
Swipe up
options at
the bottom
Swipe to display the options at the bottom.
(BottomSidebar/SourceMenu)
Multi-
Window
mode
Set the
Multi-WindowmodeOn/O.
Input
settings
InputAliasSwitch:On/O
Change the Input name to Nickname.
External
Source
Display
Settings
HDMI OUT Format :
3840 x 2160_60Hz / 1080P_60Hz / 480P_60Hz
Type-C Format :
4K, 60Hz, USB2.0 / 4K, 30Hz, USB3.0
Input Naming
Settings
System
Date &
Time
Set the
Date and Time.
Use 24-Hour Format, Automatic Date & Time, Date Format,
Timezone
Lock
Screen
Password
Setthepassword.(4-digit)
Set/Clear password, Change password
Set the shortcut menu.
Available in all channels / Available in iiWare / Disable in all
channels / Available in all channels except PC
SystemBar
Channel
Settings
Startup
&
shutdown Auto Power o:EnabletheAutoPowero function.
TheAutoPowerofunctionisenabledasdefaultsetting.
Themonitorturnsoautomatically4hoursafterthekey
or touch operation stops.
DisableAutoPowerofunctionwhenyouusethe
monitor continuously for more than 4 hours.
NOTE
ENGLISH
34 OPERATING THE MONITOR
*1 WiFi, Hotspot and Bluetooth can only be used when Option WiFi Module or Slot-PC is installed.
*2 WiFiwillbeturnedowhentheEthernetisturnedon.
*3 Available only when Option Slot-PC is installed.
*4 APK from unknown sources can be installed, the installation is done on customer own risk,
manufacture will not take any responsibility and not give any support for the installed APK’s.
Input+2580(DebugMenu:Unknownsources)
Startup
&
shutdown
Add Boot Task /
AddOTask
Select the time of each, and select
day of the week or everyday or the
business days.
Timer
Switch
Poweroreminder:On/O
Email
Set the Email.
Printing
Set the Network or WiFi direct printer.
System
update Check and update to latest FirmWare version.
Storage To display the internal system and USB disk.
Security
Credentialstorage(TrustedCredentials,UserCredentials),
Install From Storage, Clear Credentials,
Unknown sources*4:On/O
Adjustment Item Problem / Option Button to Press
[ Settings ]
System
Start up
logo
iiyama Logo displayed when the monitor is turned
on.
ENGLISH
OPERATING THE MONITOR 35
Navigation toolbar appears
The navigation toolbar can be displayed on either left side or right side of the screen.
: Back
: Home
: Back Stage
Clean all : Remove all in-progress apps
- Application -
Youcancustomizeupto7appsfrom"AllApps"tothenavigationbar.(Draganddroptheappicon)
: Note
: Finder
: Settings
:AllApps(SwitchtoPC,Browser,CloudDrive,ESHAREPro,Finder,Keeper,Note,Palette,
Settings,Viualizer,WPSOce)
- Tools -
You can customize up to 4 tools from "More" to the navigation bar.
(ClickEditinthe"More"windoworpressandholdtheicon.Andadd/removetofromthenavigation
barbyclickingthe"+"/"-"displayedontheicon.)
: Touch Menu
: Mark
Pen: Annotate
Brush: Marker
Clean: Clean the annotations, Gesture eraser
Save: Save current annotations in the screen content to picture in the storage.
Share: Share Annotation
Users can scan the QR code with a smartphone and download the annotation image to
a smartphone.
Cloud: Google Drive / One Drive
Save to Cloud Drive
Users can save notes and annotations in Note directly to one of the
cloud drives by clicking on the Cloud Storage icon in the menu. To
changethewaylesaresavedtotheCloudDrive,userscanselect
two options in the cloud storage overview.
Use the default account
When checked, all notes will be saved automatically to the default
Cloud Drive. Users will not be able to select a cloud drive.
Use the default le name when save
When checked, all notes will be saved to the selected Cloud Drive
withthedefaultlename.Userswillnotbeableto(re)namethele.
Close: Exit
ENGLISH
36 OPERATING THE MONITOR
: ScreenShare Pro
ScreenShare Pro is a multi-screen interaction software for smartphone to interactive intelligent
panel. ScreenSharePro activation code included in optional WiFI Module OWM002/SI07.
(Thedevicesuchasacomputerorsmartphoneonthesamenetwork.)
Mirroring: It is an application that displays the screen of a device such as a computer or
smartphone on the monitor.
Desktop Sync: It is an application that can control the screen of Monitor by displaying it on a
device such as a computer or Smartphone.
Remote: It is an application that allows to remotely control the monitor on a smartphone. The
Smartphone works as a Mouse/Touchpad for the screen.
Airplay/Chromecast: The device without installed ScreenShare Pro app can still connect to
ScreenShareProviaAirplay/Chromecast.(Compatibilityisnotguaranteed)
miracast: The device without installed ScreenShare Pro app can still
connecttoScreenShareProviamiracast.(Compatibilityisnotguaranteed)
:Timer(CountDown)
:Crop(ScreenCapture)
Freedom size
Full size
Window size
Save: Save in internal storage
Insert: Edit the captured image in Note, send to Note
Exit
: StopWatch
:AirClass(WiFiTeamwork)
(AvailablewhentheoptionalWiFIModuleOWM002/SI07isinstalledorwithaworkingLAN
connection.Participantsneedtobeonthesamenetwork.)
Voter / Responder / Selector / Message / Manager / Exit
: SpotLight
Setting: Zoom / Clarity
Exit
:Freeze(Freezethepicture)
Zoom +
Zoom -
Full-screen
Close: Exit
:ScreenLock(Lock/unlockthescreen)
Lock / unlock is possible by setting "Lock Screen Password" in Settings.
:More(Alltools)
:Clean(Removein-progresstool)
CloudDrive Account / Whiteboard enb and format files in Finder / Browser history will be
remove.
ENGLISH
OPERATING THE MONITOR 37
Shortcut
- App -
Drag and drop the App icon from "All apps" to create a shortcut icon on the screen.
- File / Folder -
Drag and drop a File or Folder from the Finder to create a shortcut icon on the screen.
- Website -
Create a shortcut by opening the desired website and clicking "Send the quick-link to
Desktop" in the settings menu.
- Move -
Move by long-pressing the icon and dragging and dropping.
- Remove -
Remove it by long-pressing the icon and clicking Remove from the menu.
Multi-Windows
TousetheMulti-Windowsfeature,rstturnonSettings>Personal>Multi-WindowMode.
- Resize Windows to display 4 apps on the screen at the same time.
- Drag content between apps.
Press and hold the image on the browser and drag the image to NOTE.
<Support>
Image : NOTE, Finder, Photos
Text : NOTE, Finder
ENGLISH
38 OPERATING THE MONITOR
<How to use AirClass>
The teacher click the AirClass.
UsethedevicetoscantheQRcode.(device:Androidand
mobiledeviceonthesamenetwork)Thestudentscanalsojoin
the class by entering the URL in browser.
After all students have joined the class, click "ENTER THE
CLASS".
Answer
1. The teacher write a question on the note and click the Voter.
2. The teacher select Single Choice Mode or Multiple Choice
Mode.
3. The number of students who are logged in is displayed. Then
click BEGIN.
4. After the student submitted the answer, the teacher can click
"Finish", and the answer's statistics data will be shown on the
screen.
5. Teacher selects the correct answer on the screen; the correct
answer will be green coloured, and the wrong answer will be
red coloured.
Respoder
After teacher clicks the Responser. The 1st student who clicks
the "Be Fast"icon the Notebook/Smartphone will be selected.
Selector
The teacher can click on the Selector to randomly select one
student to answer the questions.
Message
1. The teacher can enable the Message function to allow
students' messages be presented on the screen.
2. The students write their own opinions on their Notebook or
Smartphone and click to Send.
Manager
The teacher can click the Manager to display the QR code to let
other students to enter the class at any time.
Student message
ENGLISH
OPERATING THE MONITOR 39
[Note]
This is a writing software.
Canwritethecharacters,Linesandpictureslikeawhiteboard.Also,caninsertanimageorle.
Click with the touch pen.
- Tools -
Menu: Display menu of Note.
New: Save the Note writing and open a new Note.
Open:Openthele.
Save:Savethecurrentdocumenttoimageformattolebrowser.
Import:Importthepicture.(IMG/PDF/SVG)
Export : Export as IMG/PDF/SVG/IWB.
Cloud Storage: Google Drive / One Drive
Save to Cloud Drive
Users can save notes and annotations in Note directly to one of
the cloud drives by clicking on the Cloud Storage icon in the
menu.TochangethewaylesaresavedtotheCloudDrive,
users can select two options in the cloud storage overview.
Use the default account
When checked, all notes will be saved automatically to the default
Cloud Drive. Users will not be able to select a cloud drive.
Use the default le name when save
When checked, all notes will be saved to the selected Cloud Drive
withthedefaultlename.Userswillnotbeableto(re)namethele.
Background: Change the color of the background.
Send Email: Send the captured image by Email.
Customise taskbar: You can customize the taskbar by choosing tool from the "Customize
taskbar".
Brightness disabled/enabled: Enabled: Reducing the brightness automatically when writhing
the Note.
Exit: Return to main screen.
Share: Share Note
Users can scan the QR code with a smartphone and download the annotation image to
a smartphone.
List: List up all the opened Notes.
Select: Select the object being edit, can move, can zoom.
Pen:Changethewidthandcolorofthestroke.(Pen/Handwritingsize/Handwritingcolor)
Eraser:Erasethespeciedobject.
Clean All: Erase the all object.
Ruler: Ruler function
Shape: Draw the shape.
Table: Table creation
Sticky-Notes: Brainstorming tool
Preview: Display image
Undo: Cancel
Redo : Redo
Add: Add new page after the last page.
ENGLISH
40 OPERATING THE MONITOR
: To the previous page.
: To the next page.
: Page number
- Extension function of the pen -
After selecting the handwriting, the handwriting can be turn to intelligent text and for further
processing.
Tools : Color, Smartwrite, Search, Flip, Top, Clone, Delete
- Image expansion function -
After selecting the image, the image can be transformed into vector image, and the image can be
mirrored.
Tools : Crop, SVG, Flip, Top, Clone, Delete
ENGLISH
OPERATING THE MONITOR 41
[Finder (File Browser)]
Click with the touch pen.
Browsethelesstoredintheinternalstoragedevice,the USBstorage, CloudDrive andRemote
File.
Supported Format
DOC:PPT,Word,Excel,PDF(OpenthelebyusingtheWPSOce)
Note:Noteles,screenshot
Movie:.3g2.3gp.avi.v.f4v.mkv.mov.mp4.VOB.mpg/.MPEG.ts
Picture : .jpg .jpeg .webp .bmp .gif
Music:.aac.ape.ac.m4a.mp3.ogg.wav
- Tools -
: Search
: Minimization
: Maximization / restoration
: Exit
: Grid
: List
:Sort(SortsName,Time,Size,Type.)
: Select
: Select All
: Cancel
: Create
: New Win
: Copy
: Paste
: Cut
: Delete
: Rename
: Send
ENGLISH
42 OPERATING THE MONITOR
CloudDrive(GoogleDrive/OneDrive)
Save to Cloud Drive
Users can save notes and annotations in Note directly to one of the
cloud drives by clicking on the Cloud Storage icon in the menu. To
changethe wayles aresavedto theCloud Drive,userscan select
two options in the cloud storage overview.
Use the default account
When checked, all notes will be saved automatically to the default
Cloud Drive. Users will not be able to select a cloud drive.
Use the default le name when save
When checked, all notes will be saved to the selected Cloud Drive
withthedefaultlename.Userswillnotbeableto(re)namethele.
Remote File
SupportaccesstoSAMBA(SMB1.0)andFTPserver.
ENGLISH
OPERATING THE MONITOR 43
[WPS Oce]
ThisisthesoftwaretousetheleoftheOce.
Double click with the touch pen.
[Browser (Web Browser)]
Connect the network, and browse the web.
Click with the touch pen.
[Keeper]
This is the software to clean up the running application.
Double click with the touch pen.
One Key Optimize : Memory and Garbage clean
Memory Clean : Clean memory
Garbage Clean : Clean storage
[Cloud Drive]
Connect the network, and the Cloud Drive.
Click with the touch pen.
[Palette]
This is an illustration writing software.
Click with the touch pen.
[Visualizer]
Visualizer isanappthatallowsusersto connectwebcamorvisualizer(documentcamera)for
capturing live instructions or physical materials and then projecting them onto a display for viewing
and annotating.
Click with the touch pen.
[EShare Pro]
EShare is a multiscreen interaction application which makes the user experience natural and
enjoyable for home entertainment, business presentation, and educational training.
Click with the touch pen.
[iMirror]
This is software which can display an image of a smartphone on the monitor.
Click with the touch pen.
[Clean]
Clear the following :
CloudDriveAccount/WhiteboardenbformatlesinFinder/Clearbrowserhistorybrowsingcontent
Click with the touch pen.
ENGLISH
44 OPERATING THE MONITOR
SCREEN ADJUSTMENTS
The screen adjustments described in this manual are designed to set image position and minimize
ickerorblurfortheparticularcomputerinuse.
The monitor is designedtoprovidethebestperformanceatresolutionof1920 × 1080, but can
notprovidethebestatresolutionsoflessthan1920×1080becausethepictureisautomatically
stretchedtotthefullscreen.Itisrecommendedtooperateatresolutionof1920×1080innormal
use.
Displayed text or lines will be blurred or irregular in thickness when the picture is stretched due to
the screen enlargement process.
It is preferable to adjust the image position and frequency with the monitor controls, rather than
the computer software or utilities.
Perform adjustments after a warm-up period of at least thirty minutes.
Additional adjustments may be required after the Auto Adjust depending on the resolution or signal
timing.
The Auto Adjust may not work correctly when displaying the picture other than the screen
adjustment pattern. In this case, manual adjustments are required.
There are two ways to adjust the screen. One way is automatic adjustment for Position, Clock
Frequency and Phase. The other way is performing each adjustment manually.
Perform the Auto Adjust first when the monitor is connected to a new computer, or resolution is
changed.Ifthescreenhasaickerorblur,orthepicturedoesnottinthedisplayareaafterperforming
the Auto Adjust, manual adjustments are required. Both adjustments should be made by using the
screenadjustmentpattern(Test.bmp)obtainedviatheIIYAMAwebsite(http://www.iiyama.com).
Adjust the image by following the procedure below to get the desired picture.
This manual explains adjustment under Windows OS.
Display the picture at the optimum resolution.
Enter the Test.bmp (screen adjustment pattern) to wallpaper.
Consult the appropriate documentation for doing this.
Set the display position to center in the wallpaper setting dialogue box.
[Adjustment pattern]
Zebra pattern
Color bar
Picture frame
NOTE
Adjust the image by following the procedure below to get the desired picture when selecting Analog input.
ENGLISH
OPERATING THE MONITOR 45
1) Adjust the H Position so that the left side of the picture frame will move to the left edge
of the display area.
When the left side of the picture frame moves apart from the left edge of the display
areaduringtheClockadjustment,adjuststeps1)and2).
Another way to make the Clock adjustment is to correct the vertical wavy lines in the
zebra pattern.
ThepicturemayickerduringtheClock,H/VPositionadjustment.
In case the picture frame is bigger or smaller than the data display area after the
Clock adjustment, repeat steps from .
2) Stretch the right side of the picture frame to the right edge of the display area by
adjusting the Clock.
Perform the Auto Adjustment.
Adjust the image manually by following procedure below when the screen has a icker or
blur, or the picture does not t in the display area after performing the Auto Adjust.
Adjust the V Position so that the top and bottom of the picture frame will t to the display
area.
NOTE
ENGLISH
46 OPERATING THE MONITOR
Incasethestrongickerorblursremainonapartofthescreen,repeatsteps and
because the Clock may not be adjusted correctly.
Adjust the H Position after the Phase adjustment if the horizontal position moves
during the adjustment.
Adjust the Brightness and Color to get the desired picture after you complete the Clock
and Phase adjustments.
Put back your favorite wallpaper.
Adjust the Phase to correct horizontal wavy noise, icker or blur in the zebra pattern.
NOTE
ENGLISH
OPERATING THE MONITOR 47
Evenwhenusingthestandbymode,themonitorconsumeselectricity.TurnothePower
Switch whenever the monitor is not in use, during the night and weekends, to avoid
unnecessary power consumption.
NOTE
Standby Mode
Whenthe video signalfromthe computeriso,the monitorentersintoStandby Modewhich
reduces the power consumption to less than 0.5W. The screen becomes dark, and the power
indicator turns to red. From Standby Mode, the image reappears in several seconds when either
the keyboard or the mouse are touched again.
* USB peripherals and audio equipment are not connected.
00.5 W100%
POWER
CONSUMPTION
Blue
Red
Power Indicator
NORMAL MODE
STANDBY MODE
*
STANDBY FEATURE
The standby feature of this product complies with power saving requirement of VESA DPMS. When
activated, it automatically reduces unnecessary power consumption of the monitor when your
computer is not in use.
To use the feature, the monitor needs to be connected to a VESA DPMS compliant computer. There
is a standby step the monitor takes as described below. The standby function, including any timer
settingsisconguredbytheoperatingsystem.Checkyouroperatingsystemmanualforinformation
onhowthiscanbecongured.
ENGLISH
48 TROUBLE SHOOTING
The screen is not
synchronized.
The Signal Cable is properly connected.
Thesignaltimingofthecomputeriswithinthespecicationofthemonitor.
The picture does
not appear.
ThePowerCableisrmlyseatedinthesocket.
The Power Switch is turned ON.
The AC socket is live. Please check with another piece of equipment.
If the blank screen saver is in active mode, touch the keyboard or the mouse.
Increase the Contrast and/or Brightness.
The computer is ON.
The Signal Cable is properly connected.
Thesignaltimingofthecomputeriswithinthespecicationofthe
display
.
If the monitor show "No Signal", touch the keyboard or the mouse.
The computer is ON.
The Signal Cable is properly connected.
Thesignaltimingofthecomputeriswithinthespecicationofthe
display
.
The screen
position is not in
the center.
Thesignaltimingofthecomputeriswithinthespecicationofthemonitor.
The screen is too
bright or too dark.
The screen is
shaking.
Thevideo outputlevel ofthe computeriswithin thespecication ofthe
monitor.
Thepowervoltageiswithinthespecicationofthemonitor.
Thesignaltimingofthecomputeriswithinthespecicationofthemonitor.
No sound.
Theaudioequipment(computeretc.)isON.
The Audio Cable is properly connected.
The Volume is turned up.
The Mute is OFF.
Theaudiooutputleveloftheaudioequipmentiswithinthespecicationof
the monitor.
The sound is too
loud or too quiet.
Theaudiooutputleveloftheaudioequipmentiswithinthespecicationof
the monitor.
A strange noise is
heard.
The Audio Cable is properly connected.
TROUBLE SHOOTING
Problem Check
If the monitor fails to operate correctly, please follow the steps below for a possible solution.
1. Perform the adjustments described in OPERATING THE MONITOR, depending on the problem
you have. If the monitor does not get a picture, skip to 2.
2.ConsultthefollowingitemsifyoucannotndanappropriateadjustmentiteminOPERATINGTHE
MONITOR or if the problem persists.
3.
If you are experiencing a problem which is not described below or you cannot correct the problem,
discontinue using the monitor and contact your dealer or iiyama service center for further assistance.
(Powerindicator
isred.)
(Powerindicator
isblue.)
(Powerindicator
doesnotlightup.)
ENGLISH
TROUBLE SHOOTING / RECYCLING INFORMATION 49
The touch
screen shows no
response.
TheUSBCableisrmlyseatedinthesocket.
Touch screen driver software is installed.
The touch position
does not deviate.
The calibration function set up correctly.
For better environment protection please don't dispose your monitor.
Please visit our web site: www.iiyama.com for monitor recycling.
RECYCLING INFORMATION
Problem Check
ENGLISH
50 APPENDIX
APPENDIX
Designandspecicationsaresubjecttochangewithoutpriornotice.
Touch
Screen
Technology IR Touch 20points
Light transmission
88%
Hardness 7H
Thickness 4mm
Communication
system
USB serial transfer
Response time 10ms
Size Category 98"
LCD
Panel
Panel technology
IPS
Size Diagonal:97.52"(247.65cm)
Pixel pitch 0.5622mmH×0.5622mmV
Brightness 350cd/m2(Typical)
Contrast ratio 1200:1(Typical:withoutglass)
Viewable angle Horizontal:178degrees,Vertical:178degrees(Typical)
Response time 8ms(Typical,GraytoGray)
Display Colors Approx.1.07B
Sync Frequency
VGA: Horizontal: 30.0-80.0kHz, Vertical: 50-60Hz
HDMI1/2/3: Horizontal: 30.0-135.0kHz, Vertical: 24-60Hz
USB-C 3.1 Gen1: Horizontal: 30.0-135.0kHz, Vertical: 24-60Hz
Native Resolution 3840×2160,8.3MegaPixels
Supported max. resolution
VGA:1920×108060Hz
HDMI1/2/3:3840×216060Hz(YUV420/RGB444/YUV444)
USB-C3.1Gen1:3840×216060Hz
Input Connector VGA×1,HDMI×3,USB-C×1
USB Standard
USB2.0(DC5V,500mA)×1(forsoftwareupdate)
USB3.0(DC5V,900mA)×4(Front:2,Side:2)
USB-C3.1Gen1(5V,3A/9V,3A/12V,3A/20V,3.25A)×1
(DisplayPort1.4ALTmode/Touch/PowerDerivery65W)
Number of USB Ports
Connector shape
1 : Type C
2Upstream:TypeB(fortouch)
5 Downstream : Type A
Input Audio Connector ø3.5mmminijack(Stereo)
LAN RJ45×2
Serial Port RS-232C In
Plug & Play VESA DDC2BTM
Input Sync Signal Separate sync: TTL, Positive or Negative
Input Video Signal Analog:0.7Vp-p(Standard),75Ω, Positive
Digital:HDMI,USB-C3.1Gen1(DisplayPort1.4)
Input Audio Signal 2.0Vrms maximum
Output Connector
HDMI3840×216060Hz
SPDIF out Connector SPDIF
Headphone Connector ø3.5mmminijack(Stereo)
SPECIFICATIONS : ProLite TE9804MIS
ENGLISH
APPENDIX 51
* USB peripherals and audio equipment are not connected.NOTE
Speakers Internal:2Typical:16W(Stereospeakers)
iiWare Version V9.0
Maximum Screen Size 2162.0mmW×1217.4mmH/85.1"W×47.9"H
Power Source 100-240VAC, 50/60Hz, 6.0A
Power Consumption* 222W typical, Standby mode: 0.5W maximum
Dimensions / Net Weight 2244.5×1323.0×90.5mm/88.4×52.1×3.6"(W×H×D)
103.55kg / 228.29lbs
Environmental
Considerations
Operating:
Storage:
Temperature
Humidity
Temperature
Humidity
0 to 40°C / 32 to 104°F
10 to 90% (Nocondensation)
-20 to 60°C / 4 to 140°F
10 to 90% (Nocondensation)
Approvals CE, UKCA
DIMENSIONS
653.0mm/25.7”
2190.5mm/86.2”
2244.5mm/88.4”
1248.5mm/49.2”
1323.0mm/52.1”
1470.0mm/57.9”
32.5mm/1.3”
83.0mm/3.3”
90.5mm/3.6”
667.5mm/26.3”
300.0mm/11.8”
800.0mm/31.5”
600.0mm/23.6”
4xM8 SCREW HOLE
(VESA MOUNT)
4 - R8
ENGLISH
52 APPENDIX
COMPLIANT TIMING
M302A21
* means supported the timing.
Timing
VESA
VGA 640x480 31.5 60.0 25.175
SVGA 800x600 37.9 60.0 40.000
XGA 1024x768 48.4 60.0 65.000
WXGA 1280x768 47.8 60.0 79.500
QVGA 1280x960 60.0 60.0 108.000
SXGA 1280x1024 64.0 60.0 108.000
HD FWXGA 1366x768 47.7 60.0 85.500
CVT 1400x900 55.9 60.0 106.500
WSXGA 1680x1050 65.3 60.0 146.250
FHD 1920x1080 67.5 60.0 148.500
4K 3840x2160
67.5 30.0 297.000
112.5 50.0 594.000
135.0 60.0 594.000
IBM 720x400 31.5 70.0 28.320
SD
NTSC-M 15.7 60.0 13.500
NTSC-J 15.7 60.0 13.500
PAL-BDGHI 15.7 60.0 13.500
480i 60Hz 15.7 60.0 13.500
576i 50Hz 15.6 50.0 13.500
480p 60Hz 31.5 60.0 27.000
576p 50Hz 31.3 50.0 27.000
HD
720p 50Hz 37.5 50.0 74.250
60Hz 45.0 60.0 74.250
1080i 50Hz 28.1 50.0 74.250
60Hz 33.8 60.0 74.250
1080p 50Hz 56.3 50.0 148.500
60Hz 67.5 60.0 148.500
fH(kHz)
fV(Hz)
Dot clock
(MHz)
HDMI2
VGA
HDMI1
HDMI3
USB-C
(DisplayPort)