Indesit BDE 961483X W UK N User Manual
Displayed below is the user manual for BDE 961483X W UK N by Indesit which is a product in the Washer Dryers category. This manual has pages.
Related Manuals
GB
Quick Guide
THANK YOU FOR HAVING PURCHASED AN INDESIT PRODUCT.
To receive more comprehensive assistance, register the
appliance on www.indesit.com/register
CONTROL PANEL
1. ON/OFF button
2. START/PAUSE button and indicator light
3. TEMPERATURE button
4. DISPLAY
5. OPTION button
6. DRYING ONLY button
7. DRYING button
8. DELAYED START button
9. SPIN button
10. WASH CYCLE SELECTOR KNOB
11. PUSH & GO button
WASH CYCLE TABLE
Prior to using the appliance, carefully read the Safety and installation instructions.
Prior to using the appliance, the bolts used for transport must be removed. For detailed
instructions on the removal procedure, consult the safety and installation instructions.
PRODUCT DESCRIPTION
1.
3.
2.
5.
4.
7.
6.
8.
1. Top
2. Detergent dispenser drawer
3. Control panel
4. Handle
5. Porthole door
6. Drain pump (behind the plinth)
7. Plinth (removable)
8. Adjustable feet (2)
DETERGENT DISPENSER DRAWER
Compartment 1:
Do not pour detergent into the compartment 1.
Detergent should only be poured into the
compartment 2.
Compartment 2: Washing detergent (powder
or liquid)
If liquid detergent is used, the removable plastic
partition A (supplied) should be used for proper
dosage. If powder detergent is used, insert the
partition into slot B.
Compartment 3: Additives (fabric softener, etc.)
The fabric softener must never exceed the “max” level indicated on the
central pin.
! Use powder detergent for white cotton garments, for pre-washing, and
for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
! To remove the drawer, press lever C and pull the drawer outwards.
1
10
2 3
5
89
11
4
6
7
C
For all testing institutes:
2) Long cotton cycle: set programme 1 at temperature 40°C.
3) Long synthetics cycle: set cycle 2 at a temperature of 40°C.
* By selecting the 16 cycle and excluding the spin cycle, the washer-dryer will drain only.
** The duration of the wash cycles can be checked on the display.
*** After programme end and spinning with maximum selectable spin speed, in default
programme setting.
The cycle duration indicated on the display or instruction manual is an estimate based on
standard conditions. The actual duration may vary in relation to several factors, such as the
temperature and pressure of the incoming water, ambient temperature, amount of detergent,
load quantity and type, load balancing and any additional options selected. The values given
for programmes other than the Eco 40-60 programme are indicative only.
1) Eco 40-60 (Wash) - Test wash cycle in compliance with EU Ecodesign regulation
2019/2014. The most ecient programme in terms of energy and water consumption for
washing normally soiled cotton laundry.
Note: spin speed values shown on the display can slightly diers from the values stated in
the table.
4) Eco 40-60 (Wash & Drying)-
Test
wash and
drying cycle in compliance with EU
Ecodesign regulation
2019/2014
. To access “wash and dry” cycle select “Eco 40-60” wash
programme and set “Drying” option level to
“”.
The most ecient programme in terms of
energy and water consumption for washing and drying normally soiled cotton laundry. At the
end of cycle the garments can be immediately stored to the cupboard.
Maximum load 9 kg
Power input in o mode 0.5 W / in left-on mode 8 W Detergents and
Additives Recommended
detergent
Residual
dampness %
(****)
Energy
consumption
kWh
Total water lt
Laundry
temperature °C
Wash cycle Temperature Max.
spin speed
(rpm)
Max.
load for
washing
(kg)
Duration
(h : m)
Drying
Max.
load for
drying
(kg)
Wash Fabric
softener
Powder
Liquid
Setting Range 2 3
1 Cotton (2) 40 °C - 60 °C 1400 9.0 3:55 6.0 49 1.40 105 45
2 Synthetics (3) 40 °C - 60 °C 1200 4.0 2:55 4.0 35 0.80 55 43
3 Mixed 40 °C - 40 °C 1000 9.0 ** 6.0 –– – – –
4Eco 40-60 (1)
(Wash) 40 °C 40°C
1351 9.0 3:40
6.0
53 0.86 54 38
1351 4.5 2:50 53 0.68 54 37
1351 2.25 2:10 53 0.46 40 34
5 White 60 °C - 90 °C 1400 9.0 2:45 6.0 49 0.90 90 55
6 Delicates 30 °C - 30 °C 0 1.0 ** 1.0 –– – – –
7 Colours 40 °C - 40 °C 1400 9.0 ** 6.0 –– – – –
8 Dark 30 °C - 30 °C 800 5.0 ** 5.0 –– – – –
9 Antiodour 40°C - 40 °C 1000 3.5 ** 3.5 – – – –
10 20°C 20 °C - 20 °C 1400 9.0 1:50 6.0 –49 0.16 90 22
11 Wool 40 °C - 40 °C 800 2.0 ** 2.0 –– – – –
12 Rapid 30’ 30 °C - 30 °C 800 4.5 0:30 – – –71 0.20 45 27
13 Wash&Dry 45‘ 30 °C 30 °C 1400 1.0 ** 1.0 –– – – –
14 AirFresh – – – – ** 1.5 – – – – – – – –
15 Rinse + Spin – – 1400 9.0 ** 6.0 – – – – – – –
16 Spin + Drain * – – 1400 9.0 ** 6.0 – – – – – – – –
Required dosage Optional dosage
4Eco 40-60 (4)
(Wash & Drying) 40 °C 40 °C 1351 6.0 9:20 6.0 0 3.80 75 33
1351 3.0 5:10 3.0 0 1.98 47 32
WASH CYCLES
Follow the instructions on the symbols of the garment’s wash
care label. The value indicated in the symbol is the maximum
recommended temperature for washing the garment.
Cotton: suitable for washing towels, underwear, table cloths,
etc. made of resistant linen and cotton that are moderately to heavily
soiled.
Synthetics: specic for synthetic items. If the dirt is dicult to remove,
the temperature can be increased up to 60° and powder detergent can be
used too.
Mixed: for washing lightly to normally soiled resilient garments in cotton,
linen, synthetic bres and mixed bres.
Eco 40-60: for washing normally soiled cotton garments declared to be
washable at 40 °C or 60 °C, together in the same cycle. This is the standard
cotton programme and the most ecient in terms of water and energy
consumption.
White: suitable for resistant linen and cotton that are heavily soiled.
Delicates: use programme 6 to wash very delicate garments. It is
advisable to turn the garments inside out before washing them. For best
results, use liquid detergent on delicate garments.
When selecting an exclusively time-based drying function, a drying cycle is
performed at the end of the wash cycle that is particularly delicate, thanks
to light handling and appropriate temperature control of the water jet.
The recommended durations are:
1 kg of synthetic garments --> 150 min
1 kg of synthetic and cotton garments --> 180 min
1 kg of cotton garments --> 180 min
The degree of dryness depends on the load and fabric composition.
Colours: a 40°C cycle that helps to preserve colours, suitable for cotton or
synthetic coloured garments. It allows for reducing electricity
consumption for heating the water while guaranteeing good washing
results. Suitable for lightly soiled garments.
Dark: use programme 8 to wash dark-coloured garments. This
programme is designed to maintain dark colours over time. We
recommend using a liquid detergent for the best results when washing
dark-coloured garments.
When you select the drying function, at the end of the washing cycle the
machine will automatically perform a delicate drying cycle that preserves the
colours of the garments. The display will show the level “ ”. Max. load: 5 kg.
Antiodour: use programme 9 for washing garments with bad odours (e.g.
smoke, sweat, fried food). The programme is designed to remove bad
odours while preserving the fabric bres. Synthetics fabrics or mixed
loads should be washed at 40°.
20°C: for washing lightly soiled cotton garments, at a temperature of 20 °C.
Wool - Woolmark Apparel Care - Blue:
The “Wool” wash cycle is approved by the Woolmark
Company for washing wool garments classied as
“hand-washable”, provided that the wash complies with
the instructions appearing on the garment’s label and
with those provided by the manufacturer of this
washer-dryer. (M1318)
Rapid 30’: this programme is designed to wash lightly soiled garments at
30° (excluding wool and silk) with a 4.5 kg maximum load in a short time:
it only lasts 30 minutes and allows for saving time and energy.
Wash&Dry 45’: select programme 13 for washing and drying lightly
soiled garments (Cotton and Synthetic) in a short time. This cycle may be
used to wash and dry a laundry load of up to 1 kg in just 45 minutes. To
achieve optimum results, use liquid detergent and pre-treat cus, collars
and stains.
AirFresh: ideal cycle to refresh garments and remove bad odours, in
particular smoke, from cotton and synthetic items in 30’ (max. 1.5 kg)
without the washing phase.
Rinse + Spin: designed for rinsing and spinning.
Spin + Drain: designed to spin and drain the water.
DISPLAY
The display is useful when programming the machine and provides a lot
of information.
The duration of the available wash cycles and the remaining time of a
running cycle appear in section A; if the Delayed Start option has been
set, the countdown to the start of the selected cycle will appear.
Pressing the corresponding button allows you to view either the
maximum spin speed, temperature and drying time values attained by
the machine during the set wash cycle, or the values selected most
recently (if compatible with the set wash cycle).
The hourglass ashes while the machine processes the data on the basis
of the selected cycle. After a maximum of 10 minutes, the icon remains
steady lit and the nal time remaining is displayed. The “hourglass” icon
will then switch o approximately 1 minute after the nal time remaining
has been displayed.
The “washing phases” relative to the selected cycle and the “washing
phase” of the running cycle appear in section B:
Wash
Rinse
Spin/ Drain
Drying
When lit, the symbol indicates that the set “Delayed Start” value has
appeared on the display.
There are three levels in section C relative to the washing options.
Section D includes the icons related to the three dierent drying levels as
well as the icon , which lights up when a timed drying option is set.
DOOR LOCKED INDICATOR
When lit, the symbol indicates that the door is locked. To prevent any
damage, wait until the symbol turns o before opening the door.
To open the door while a cycle is in progress, press the START/PAUSE
button ; if the symbol is o, the door can be opened.
FIRSTTIME USE
Once the appliance has been installed, and before it is used for the rst
time, run a wash cycle with detergent and no laundry, by setting the
“Auto-Clean” cycle.
DAILY USE
Prepare the laundry by following the suggestions appearing under the
“TIPS AND SUGGESTIONS” section.
Rapid programming
- Press the ON/OFF button ; the START/PAUSE indicator light will
ash slowly green.
- Open the door. Load the laundry while making sure not to exceed the
maximum load quantity indicated in the cycle table.
- Pull out the detergent dispenser drawer and pour the detergent into the
relevant compartments as described in “DETERGENT DISPENSER DRAWER”
section.
- Close the door.
- Press the PUSH & GO button to start the wash cycle.
Traditional programming
- Press the ON/OFF button ; the START/PAUSE indicator light will
ash slowly green.
- Open the door. Load the laundry while making sure not to exceed the
maximum load quantity indicated in the Wash Cycle Table.
- Pull out the detergent dispenser drawer and pour the detergent into the
relevant compartments as described in “DETERGENT DISPENSER DRAWER”
section.
- Close the door.
- Use the WASH CYCLE selector knob to select the desired wash cycle: it
will be associated with a specic temperature and spin speed that can be
modied. The duration of the cycle will appear on the display.
- Modify the temperature and/or spin speed: the machine automatically
displays the maximum temperature and spin speed values set for the
selected cycle, or the most recently-used settings if they are compatible
with the selected cycle. Pressing the button gradually reduces the
temperature down to the cold wash “OFF” setting. Pressing the button
gradually reduces the spin speed until it is completely excluded (“OFF”
setting). Pressing these buttons again restores the maximum values.
- Select the desired options.
- Press the START/PAUSE button to start the wash cycle; the relative
indicator light will light up steady green and the door will lock ( symbol on).
PAUSING A CYCLE
To pause the wash cycle, press the START/PAUSE button again; the
indicator light will ash amber. If the symbol is not lit, the door may be
opened. To start the wash cycle from the point at which it was
interrupted, press the START/PAUSE button again.
OPENING THE DOOR, IF NECESSARY
Once a cycle starts, the symbol turns on to signal that the door cannot
be opened. While a wash cycle is running, the door remains locked. To
open the door while a cycle is under way, for example, to add or remove
garments, press the START/PAUSE button to pause the cycle; the
indicator light will ash amber. If the symbol is not lit, the door may be
opened. Press the START/PAUSE button again to continue the cycle.
CHANGING A RUNNING WASH CYCLE
To change a wash cycle while it is in progress, pause the washer-dryer
using the START/PAUSE button (the relative indicator light will ash
amber), then select the desired cycle and press the START/PAUSE
button again.
! To cancel a cycle that has already begun, press and hold the ON/OFF
button. The cycle will be stopped and the machine will switch o.
END OF THE CYCLE
This will be indicated by the word “END” on the display; when the
symbol switches o, the door may be opened. Open the door, unload the
laundry and switch o the machine. If you do not press ON/OFF
button, the washing machine will switch o automatically after about a
10 minutes.
D
B
C
A
OPTIONS
- If the selected option is not compatible with the set wash cycle, the
indicator light will ash and the option will not be activated.
Stain removal
This option allows for selecting the type of dirt so as to optimally adjust the
cycle for removing the stains. The following types of dirt can be selected:
- Food, for stains caused by foodstus and beverages, for example.
- Work, for grease and ink stains, for example.
- Outdoor, for mud and grass stains, for example
! The wash cycle duration varies according to the type of selected dirt.
Delayed Start - ( )
To set a delayed start for the selected cycle, press the corresponding
button repeatedly until the desired delay period has been reached. When
this option has been activated, the symbol lights up on the display. To
remove the delayed start setting, press the button until the word “OFF”
appears on the display.
Temperature - ( )
Each wash cycle has a pre-dened temperature. To modify the
temperature, press the button. The value will appear on the display.
Spin
Each wash cycle has a pre-dened spin speed. To modify the spin speed,
press the button. The value will appear on the display.
Setting the drying cycle
The rst time the button is pressed, the machine will automatically
select the maximum drying cycle which is compatible with the selected
wash cycle. Subsequent presses will decrease the drying level and then the
drying time, until the cycle is excluded completely (“OFF”).
Drying may be set as follows:
A- Based on the desired laundry dryness level:
Cupboard : suitable for laundry which can be put back in a cupboard
without being ironed.
Hanger : ideal for clothes which do not need to be dried fully.
Iron : suitable for clothes which will need ironing afterwards. the
remaining dampness softens creases, making them easier to remove.
B - Based on a set time period: between 210 and 30 minutes.
If your laundry load to be washed and dried is much greater than the
maximum stated load (see adjacent table of wash cycles), perform the
wash cycle, and when the cycle is complete, divide the garments into
groups and put some of them back in the drum. At this point, follow the
instructions provided for a “Drying only” cycle. Repeat this procedure for
the remainder of the load. Note: a cooling-down period is always added to
the end of each drying cycle.
Drying only
Press button to perform the drying-only cycle. After selecting the
desired cycle (compatible with the type of garments), press button to
exclude the washing phase and start the drying phase at the maximum
level for the selected cycle. The drying level or time may be set and
changed by pressing the drying button .
(Not compatible with cycles 13 and 14).
PUSH & GO
To start the Push&Go cycle press and hold the button for 2 seconds.
The indicator lights up to show that the cycle has started. The wash and
drying cycle is ideal for cotton or synthetic fabrics, as it washes them at
a temperature of 30° and a maximum spin speed of 1000 rpm. During
the drying cycle the maximum temperature is 60°C. At the end of the
cycle the residual humidity will be the same as for the “ ” level. Max
recommended load 3 kg.
The time displayed is the maximum time allowed by the Push&Go cycle.
If the load is lower than the maximum load or most garment are made of
synthetic materials, the actual time of the cycle will be shorter.
How does it work?
1. Load the laundry (cotton and/or synthetic garments) and close the door.
2. Pour the detergent and/or additives.
3. Start the cycle by pressing and holding the Push&Go button for 2
seconds. The relevant indicator light will turn green and the door will lock
(the DOOR LOCKED symbol is lit).
NB: starting the cycle through the Push&Go button activates an automatic
non-customisable wash and drying cycle recommended for cotton and
synthetic fabrics.
4. The automatic cycle can be used only for washing, excluding the drying
phase. Press the Push&Go button and then the drying button : the
drying icon of the “ ” level will switch o. Maximum load for washing-only
is 4 kg. The cycle cannot be customised further.
To open the door while an automatic cycle is under way, press the START/
PAUSE button. If the DOOR LOCKED symbol is o, the door may be opened
only during the washing phase. Press the START/PAUSE button again to
restart the wash cycle from the point at which it was interrupted.
5. At the end of the wash cycle the word END will light up.
TIPS AND SUGGESTIONS
Divide the laundry according to:
Type of fabric (cotton, mixed bres, synthetics, wool, garments to be
hand-washed). Colour (separate coloured garments from whites, wash new
coloured garments separately). Delicates (small garments – such as nylon
stockings – and items with hooks – such as bras: insert them in a fabric bag).
Empty the pockets:
Objects such as coins or lighters can damage the washer-dryer and the
drum. Check all buttons.
Follow the dosage recommendation / additives
It optimizes the cleaning result, it avoids irritating residues of surplus detergent
in your laundry and it saves money by avoiding waste of surplus detergent.
Use low temperature and longer duration
The most ecient programmes in terms of energy consumption are
generally those that perform at lower temperatures and longer duration.
Observe the load sizes
Load your washing machine up to the capacity indicated in the
“Wash Cycle Table” table to save water and energy.
Noise and remaining moisture content
They are inuenced by the spinning speed: the higher the spinning speed
in the spinning phase, the higher the noise and the lower the remaining
moisture content.
CARE AND MAINTENANCE
Before performing cleaning and maintenance, switch the washer-dryer o
and disconnect it from the mains power. Do not use ammable liquids to
clean the washer-dryer. Clean and maintain your washer-dryer periodically
(at least 4 times per year).
Disconnect the water and power supplies
Close the water tap after every wash. This will limit wear on the hydraulic
system inside the washer-dryer and help to prevent leaks. Unplug the
washer-dryer when cleaning it and during all maintenance work.
Clean the washer-dryer
The outer parts and rubber components of the appliance can be cleaned
using a soft cloth soaked in lukewarm soapy water. Do not use solvents or
abrasives. The washer-dryer has a “Auto-clean” cycle for its internal parts; it
must be run without any load in the drum.
To optimise this cycle, it is possible to use either detergent (10% of the
quantity specied for lightly soiled garments) or special additives to clean
the washer-dryer. We recommend running a cleaning cycle every 40 wash
cycles. To start the cycle press buttons and simultaneously for 5
seconds. The cycle will start automatically and will run for about 70
minutes. To stop the cycle, press the START/PAUSE button.
Clean the detergent dispenser drawer
Wash it under running water; this operation should be repeated frequently.
Care for the door and drum
Always leave the porthole door ajar in order to prevent unpleasant odours
from forming.
Clean the pump
The washer-dryer is tted with a auto-cleaning pump that does not require any
maintenance. Small items (such as coins or buttons) may sometimes fall into
the protective pre-chamber situated at the base of the pump.
! Make sure the wash cycle has ended and unplug the appliance.
To access the pre-chamber:
1. remove the cover panel on the front of the machine by rst pressing it
in the centre then pushing downwards on both sides to extract it;
2. loosen the drainage pump cover by turning it anti-clockwise: it is
normal for some water to leak out;
3. clean the inside thoroughly;
4. screw the cover back on;
5. put the panel back in place, making sure the hooks slot in place before
pushing the panel onto the appliance.
Check the water inlet hose
Check the water inlet hose at least once a year. If it is cracked or broken, it
must be replaced: during wash cycles, the high pressure of the water
could suddenly split the hose open.
! Never use hoses that have already been used.
LOAD BALANCING SYSTEM
Before every spin cycle, to avoid excessive vibrations before every
spin and to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the washing
rotation speed. If, after several attempts, the load is not balanced
correctly, the machine spins at a reduced spin speed. If the load is
excessively unbalanced, the washer-dryer performs the distribution
process instead of spinning. To encourage improved load distribution and
balance, we recommend small and large garments are mixed in the load.
ACCESSORIES
Contact our Technical Assistance Service to check whether the following
accessories are available for this washer-dryer model.
Stacking kit
With this accessory you can secure the tumble dryer to the upper part of
your washer-dryer to save space and facilitate loading and unloading of
the tumble dryer.
TRANSPORT AND HANDLING
Do not lift the washer-dryer by gripping it from the upper section.
Unplug the appliance and close the water tap. Check that the door and
detergent dispenser drawer are tightly closed. Detach the lling hose
from the water tap then detach the drain hose. Empty all the water
remaining in the hoses and secure the latter so that they do not get
damaged during transport. Apply the transport bolts back on. Repeat, in
reverse order, the transport bolt removal procedure described in the
“Health & Safety and Installation Guides”.
DEMO MODE: to deactivate this function, switch the washing machine OFF.
Than press and hold “Start/Pause” button, within 5 seconds press also
“ON/OFF” button and hold both buttons for 2 seconds.
400011541571
TROUBLESHOOTING
Your machine could occasionally fail to work. Before contacting the Technical Assistance Service, make sure that the problem cannot be easily solved using the following list.
Anomalies Possible causes / Solution
The machine does not switch on. The appliance is not plugged into the socket fully, or not enough to make contact.
There is no power to the socket, or the fuse has blown in the mains plug.
The wash cycle does not start.
The door is not closed properly.
The ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap has not been turned on to allow water to ow into the machine.
A delayed start has been set.
The washer-dryer does not dry. Check the 2 sections above.
The “Drying” is set to “OFF”.
The machine does not ll with water
(“H2O” appears on the display).
The water inlet hose is kinked.
The water inlet hose is not connected to the water supply.
The water pressure is too low.
The water tap has not been turned on to allow water to ow into the machine.
There is no water supply to the house.
The inlet valve lter is blocked.
The START/PAUSE button has not been pressed.
The machine continuously lls with water
and continually drains away or Water left
in the drum or Stuck on wash.
The top of the drain hose is too low - It must be tted at a height between 65 and 100 cm from the oor.
The drain hose is connected incorrectly to the sink trap allowing water to run into the machine, the drain hose
must be positioned higher than the bottom of the sink to prevent water owing down the drain hose.
The end of the drain hose has been pushed too far down the standpipe, the ‘U’ bracket should be tted 100
mm from the end of the drain hose.
The machine does not drain or spin - (error
lights ashing).
The Pump lter is blocked.
The drain hose is kinked.
New Installation - The blanking cap or spigot has not been removed if connected under a sink.
The drain hose or sink trap is blocked.
The machine does spin. The ‘Spin’ Speed is set to “OFF”.
The machine does not heat or poor wash results. The ‘Temperature’ is set to “OFF”.
The programme takes too long. Programme times will vary due to water pressure, the incoming water temperature and if the wash load goes
out of balance. This will increase the programme times accordingly.
The Display sticks at one ‘time to end’
for more than 1 Minute or the Display
changes the estimated ‘Time to End’
during the programme.
The display time is for guidance only - it is not a precise time to nish and may vary.
The washer-dryer vibrates a lot during the
spin cycle.
The feet have not been adjusted, enabling the machine to rock.
New Installation - Either the Transit Bolts including the plastic spacers, or the Polystyrene Packaging have not
been removed when installing the machine.
The machine is trapped between cabinets and/or walls.
The load is in a slight out of balance condition and machine is spinning, but at a lower speed.
The machine is noisy. There will always be some motor, pump and drum noise during spin.
The machine leaks from the
dispenser.
The dispenser drawer is blocked with detergent and requires cleaning.
The water pressure is too high and requires turning down - turn down the tap on the water supply pipe slightly and try again.
The machine is tilting forwards - It must be level when in its nal position.
The “Options” and START/PAUSE
indicator lights ash rapidly and the display
visualises an error code (e.g.: F-01, F-...).
Switch o the machine and unplug it, wait for approximately 1 minute and then switch back on again. If the
problem persists contact Technical Assistance Centre.
The machine smells. The machine requires a service wash. Run a auto clean wash cycle with detergent and no laundry.
The water level is too low when the
machine is washing. The water level is correct if it can be seen at the bottom of the door.
There is too much foam. The detergent is not suitable for machine washing (it should display the text
‘for washing machine’ or ‘hand and machine wash’ or the like).
The PUSH & GO function does not activate. After switching on the machine, a control other than PUSH & GO was activated. Switch the machine o and
press the PUSH & GO button.
You can download the Safety Instructions, Product Fiche and Energy data by:
• Visiting our website - http://docs.indesit.eu
• Using QR Code
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When
contacting our After-sales Service, please state the codes provided on your product’s identication plate.
• For User’s Repair & Maintenance Information visit www.indesit .com
The model information can be retrieved using the QR-Code reported in the energy label. The label also includes
the model identier that can be used to consult the portal of the registry at https://eprel.ec.europa.eu
xxxxxxxxxxxx xxxx