Indesit BWD 71453 K UK User Manual

Displayed below is the user manual for BWD 71453 K UK by Indesit which is a product in the Washing Machines category. This manual has pages.

Related Manuals

Indesit BWD 71453 W UK Manual

Indesit BWD 71453 S UK Manual

Indesit BWD 71253 W EU Manual

Hotpoint BI WMHL 71453 UK Manual

Indesit XWDE 861480X K UK Manual

Indesit BWE 91484X K UK Manual

Indesit BWE 71452 K UK N Manual

Indesit SI8 1Q WD UK.1 Manual

Contents

Installation, 2-3-4-5

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Care and maintenance, 6

Cutting off the water or electricity supply

Cleaning the washing machine

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Precautions and tips, 7

General safety

Load balancing system

Disposal

Description of the washing machine

and starting a wash cycle, 8-9

Control panel

Indicator lights

Starting a wash cycle

Wash cycles, 10

Push & Wash

Table of wash cycles

Personalisation, 11

Setting the temperature

Setting the spin speed

Functions

Detergents and laundry, 12

Detergent dispenser drawer

Preparing the laundry

Garments requiring special care

Troubleshooting, 13-14

Product Guarantee and Repair Informa-

tion, 15

BWD 71453

Instructions for use

WASHING MACHINE

English,1

Levelling the machine correctly will provide

it with stability, help to avoid vibrations and

excessive noise and prevent it from shifting

while it is operating. If it is placed on carpet or

a rug, adjust the feet in such a way as to allow

a sufficient ventilation space underneath the

washing machine.

Connecting the electricity and water

supplies

Connecting the water inlet hose

1. Connect the sup-

ply pipe by screwing

it to a cold water tap

using a ¾ gas threa-

ded connection (see

figure).

Before performing the

connection, allow the

water to run freely un-

til it is perfectly clear.

2. Connect the inlet

hose to the washing

machine by screwing

it onto the correspon-

ding water inlet of the

appliance, which is

situated on the top

right-hand side of the

rear part of the ap-

pliance (see figure).

3. Make sure that the hose is not folded over

or bent.

! The water pressure at the tap must fall within

the range of values indicated in the Technical

data table (see next page).

! If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

! Never use second-hand hoses.

! Use the ones supplied with the machine.

Installation

! This instruction manual should be kept in a

safe place for future reference. If the washing

machine is sold, transferred or moved, make

sure that the instruction manual remains with

the machine so that the new owner is able to

familiarise himself/herself with its operation

and features.

! Read these instructions carefully: they con-

tain vital information relating to the safe instal-

lation and operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washing machine from its

packaging.

2. Make sure that the washing machine has

not been damaged during the transportation

process. If it has been damaged, contact the

retailer and do not proceed any further with

the installation process.

3. Remove the 4 pro-

tective screws (used

during transportation)

and the rubber wa-

sher with the cor-

responding spacer,

located on the rear

part of the appliance

(see figure).

4. Close off the holes using the plastic plugs

provided.

5. Keep all the parts in a safe place: you will

need them again if the washing machine ne-

eds to be moved to another location.

! Packaging materials should not be used as

toys for children.

Levelling

1. Install the washing machine on a flat sturdy

floor, without resting it up against walls, furni-

ture cabinets or anything else.

2. If the floor is not

perfectly level, com-

pensate for any une-

venness by tightening

or loosening the

adjustable front feet

(see figure); the angle

of inclination, measu-

red in relation to the

worktop, must not

exceed 2°.

Connecting the drain hose

Connect the drain

hose, without bending

it, to a draining duct or

a wall drain situated

between 65 and 100

cm from the floor;

The drain hose may

be connected to an

under-sink trap. Be-

fore connecting the

drain hose from the

machine ensure that

any blanks or remo-

vable ends have been

taken off the spigot.

If it is placed over the

edge of a basin or sink

be sure the free end of

the hose should not

be underwater.

! We advise against the use of hose extensions; in

case of absolute need, the extension must have the

same diameter as the original hose and must not

exceed 150 cm in length. Ensure that if the drain

hose is pushed into a standpipe, that the end does

not go down more than 15cms (6 inches). If the hose

is pushed down too far, this may cause the machine

to self -syphon ie. continuously empty as it is filling.

Electric connections

Before plugging the appliance into the mains

socket, make sure that:

• the socket is earthed and in compliance with

the applicable law;

• the socket is able to sustain the appliance’s

maximum power load indicated on the Technical

Data Plate fixed on the machine;

65 - 100 cm

Where it connects to

the waste water pipe

cut end off spigot or

remove the blanking cap

• the supply voltage is included within the values

indicated on the Technical Data Plate fixed on

the machine.

• the socket is compatible with the washing

machine’s plug. If this is not the case, replace

the socket or the plug.

Your appliance is now supplied with a 13 amp fu-

sed plug it can be plugged into a 13 amp socket

for immediate use. Before using the appliance

please read the instructions below.

WARNING - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE

CARRIED OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be

used, and the fuse cover re-fitted. If the fuse

cover is lost, the plug must not be used until a

replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of

the correct colour as indicated by the coloured

marking or the colour that is embossed in words

on the base of the plug. Replacements can be

obtained directly from your nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded

plug and you should wish to re-route the mains

cable through partitions, units etc., please en-

sure that either:

the plug is replaced by a fused 13 ampere rewi-

reable plug bearing the BSI mark of approval.

or:

the mains cable is wired directly into a 13 amp

cable outlet, controlled by a switch, (in complian-

ce with BS 5733) which is accessible without

moving the appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself,

you make the pins unusable so that it cannot be

accidentally inserted into a socket.

Instructions for connecting cable to an alterna-

tive plug:

Important: the wires in the mains lead are co-

loured in accordance with the following code:

Green & Yellow Earth

Blue Neutral

Brown Live

Technical data

Model BWD 71453

Dimensions

width 59.5 cm

height 85 cm

depth 54 cm

Capacity from 1 to 7 kg

Electrical

connections

please refer to the technical

data plate fixed to the machine

Water

connections

maximum pressure

1 MPa (10 bar)

minimum pressure

0.05 MPa (0.5 bar)

drum capacity 52 litres

Spin speed up to 1400 rotations per minute

Test wash

cycles in

accordance

with re-

gulations

1061/2010

and

1015/2010

Programme 9:

Eco Cotton 60°.

Programme 9:

Eco Cotton 40°.

This appliance conforms to

the following EC Directives:

- EMC 2014/30/EU (Electro-

magnetic Compatibility)

- LVD 2014/35/EU (Low

Voltage)

- 2012/19/EU (WEEE)

As the colours of the wires in the lead may not

correspond with the coloured markings iden-

tifying the terminals in your plug, proceed as

follows:

Connect Green & Yellow wire to terminal

marked E or or coloured Green or Green &

Yellow.

Connect Brown wire to terminal marked L or

coloured Red.

Connect Blue wire to terminal marked N or co-

loured Black.

If a 13 amp plug (BS 1363) is used it must be

fitted with a 13 amp fuse, either in the plug or

adaptor or at the distribution board.

If you are in any doubt regarding the electrical

supply to your machine, consult a qualified

electrician before use.

How to connect an alternative plug:

The wires in this mains lead are coloured in

accordance with the following code:

BLUE NEUTRAL (N)

BROWN LIVE (L)

GREEN & YELLOW EARTH (E)

Disposing of the appliance:

When disposing of the appliance please re-

move the plug by cutting the mains cable as

close as possible to the plug body and dispo-

se of it as described above.

! The washing machine should not be installed

in an outdoor environment, not even where

the area is sheltered, because it may be very

dangerous to leave it exposed to damp, rain

and thunderstorms.

! When the washing machine is installed, the

mains socket must be within easy reach.

! Do not use extensions or multiple sockets.

! The power supply cable must never be bent

or dangerously compressed.

! The power supply cable must only be repla-

ced by an authorised serviceman.

Warning! The company denies all liability if and

when these norms are not respected.

The first wash cycle

Once the appliance has been installed, and

before you use it for the first time, run a wash

cycle with detergent and no laundry, using the

wash cycle “Auto Clean” (see “Cleaning the

washing machine”).

GREEN &

YELLOW

BROWN

BLUE

13 ampere fuse

CROSS-BAR

CORD GRIP

Care and maintenance

Cleaning the pump

The washing machine is fitted with a self-

cleaning pump which does not require any

maintenance. Sometimes, small items (such

as coins or buttons) may fall into the protective

pre-chamber at the base of the pump.

! Make sure the wash cycle has finished and

unplug the appliance.

To access the pre-chamber:

1. Take off the cover

panel on the front of

the machine by first

pressing it in the cen-

tre and then pushing

downwards on both

sides until you can re-

move it (see figures).

2. Unscrew the lid

by rotating it anti-

clockwise (see figu-

re): a little water may

trickle out. This is

perfectly normal.

3. Clean the inside thoroughly.

4. Screw the lid back on.

5. Reposition the panel, making sure the hooks

are securely in place before you push it onto

the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If

there are any cracks, it should be replaced

immediately: during the wash cycles, water

pressure is very strong and a cracked hose

could easily split open.

! Never use second-hand hoses.

Cutting off the water and electricity

supplies

• Turn off the water tap after every wash cycle.

This will limit wear on the hydraulic system inside

the washing machine and help to prevent leaks.

• Unplug the washing machine when cleaning it

and during all maintenance work.

Cleaning the washing machine

• The outer parts and rubber components

of the appliance can be cleaned using a soft

cloth soaked in lukewarm soapy water. Do not

use solvents or abrasives.

• The washing machine has a “Auto Clean”

programme for its internal parts that must be

run with no load in the drum.

For maximum performance you may want

to use either the detergent (i.e. a quantity

10% the quantity specified for lightly-soiled

garments) or special additives to clean the

washing machine. We recommend running a

cleaning programme every 40 wash cycles.

To start the programme press buttons A and

B simultaneously for 5 seconds (see figure).

The programme will start automatically and

will last approximately 70 minutes. To stop the

cycle press the START/PAUSE button.

Cleaning the detergent dispenser

drawer

To remove the drawer,

press lever (1) and pull

the drawer outwards (2)

(see figure).

Wash it under running

water; this procedure

should be repeated fre-

quently.

Caring for the door and drum of your

appliance

• Always leave the porthole door ajar in order to

prevent unpleasant odours from forming.

Precautions and tips

! This washing machine was designed and constructed in

accordance with international safety regulations. The fol-

lowing information is provided for safety reasons and must

therefore be read carefully.

General safety

• This appliance was designed for domestic use only.

• This appliance can be used by children aged

from 8 years and above and persons with re-

duced physical, sensory or mental capabilities

or lack of experience and knowledge if they

have been given supervision or instruction

concerning use of the appliance in a safe way

and understand the hazards involved. Children

shall not play with the appliance. Cleaning and

user maintenance shall not be made by children

without supervision.

• The washing machine must only be used by adults, in accor-

dance with the instructions provided in this manual.

• Do not touch the machine when barefoot or with wet or

damp hands or feet.

• Do not pull on the power supply cable when unplugging

the appliance from the electricity socket. Hold the plug

and pull.

• Do not open the detergent dispenser drawer while the

machine is in operation.

• Do not touch the drained water as it may reach extreme-

ly high temperatures.

• Never force the porthole door. This could damage the safety

lock mechanism designed to prevent accidental opening.

• If the appliance breaks down, do not under any circum-

stances access the internal mechanisms in an attempt

to repair it yourself.

• Always keep children well away from the appliance while

it is operating.

• The door can become quite hot during the wash cycle.

• If the appliance has to be moved, work in a group of two

or three people and handle it with the utmost care. Never

try to do this alone, because the appliance is very heavy.

• Before loading laundry into the washing machine, make

sure the drum is empty.

Load balancing system

Before every spin cycle, to avoid excessive vibrations and

to distribute the load in a uniform manner, the drum rotates

continuously at a speed which is slightly greater than the

washing rotation speed. If, after several attempts, the load is

not balanced correctly, the machine spins at a reduced spin

speed. If the load is excessively unbalanced, the washing ma-

chine performs the distribution process instead of spinning.

To encourage improved load distribution and balance, we

recommend small and large garments are mixed in the load.

Disposal

• Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

•The European Directive 2012/19/EU - WEEE on Waste

Electrical and Electronic Equipment, requires that old

household electrical appliances must not be disposed

of in the normal unsorted municipal waste stream. Old

appliances must be collected separately in order to

optimise the recovery and recycling of the materials they

contain and reduce the impact on human health and the

environment. The crossed out “wheeled bin” symbol on

the product reminds you of your obligation, that when

you dispose of the appliance it must be separately

collected.

Consumers should contact their local authority or retailer

for information concerning the correct disposal of their

old appliance.

Detergent dispenser drawer: used to dispense deter-

gents and washing additives (see “Detergents and laundry”).

ON/OFF button: switches the washing machine on and off.

PUSH & WASH button: (see “Wash cycles”).

WASH CYCLE knob: programmes the wash cycles. During

the wash cycle, the knob does not move.

FUNCTION buttons with indicator light: used to select the

available functions. The indicator light corresponding to the

selected function will remain lit.

CHILD LOCK button with indicator light: to activate

the control panel lock, press and hold the button for

approximately 2 seconds. When the indicator light is

illuminated, the control panel is locked (apart from the ON/

OFF button). This means it is possible to prevent wash cycles

from being modified accidentally, especially where there are

children in the home. To deactivate the control panel lock,

press and hold the button for approximately 2 seconds.

TEMPERATURE

knob and indicator light

: sets the tempe-

rature or the cold wash cycle (see “Personalisation”).

SPIN SPEED

knob and indicator light

: sets the spin speed

or exclude the spin cycle completely (see “Personalisation”).

DISPLAY: used to view the duration of the various cycles

available and the remaining time of a cycle in progress; if the

DELAY TIMER option has been selected, the countdown to

the start of the selected cycle will appear:

DELAY TMER button: press to set a delayed start time for

the selected wash cycle. The delay time will be shown on

the display.

DOOR LOCKED indicator light: indicates whether the door

may be opened or not (see next page).

START/PAUSE button with indicator light: starts or tempo-

rarily interrupts the wash cycles.

N.B. To pause the wash cycle, press this button - the rele-

vant indicator light will flash in an amber colour. If the DOOR

LOCKED indicator light is switched off, the door may be

opened (wait approximately 3 minutes).

To start the wash cycle from the point at which it was inter-

rupted, press this button again.

Standby mode

This washing machine, in compliance with new energy saving

regulations, is fitted with an automatic standby system which

is enabled after about 30 minutes if no activity is detected.

Press the ON-OFF button briefly and wait for the machine

to start up again.

Description of the washing

machine and starting a wash cycle

Control panel

DOOR

LOCKED

indicator light

START/PAUSE

button with indicator

light

Detergent dispenser drawer

ON/OFF

button

WASH CYCLE

knob

DELAY TIMER

button

FUNCTION

buttons with

indicator lights

PUSH & WASH

button

TEMPERATURE

knob and indicator light

SPIN SPEED

knob and indicator light

DISPLAY

CHILD LOCK

button with

indicator light

Indicator lights

The indicator lights provide important information.

This is what they can tell you:

Function buttons and corresponding indicator lights

When a function is selected, the corresponding indicator

light will illuminate.

If the selected function is not compatible with the program-

med wash cycle, the corresponding indicator light will flash

and the function will not be activated.

If the selected option is not compatible with another

previously selected option, the indicator light will flash

accompanied by a buzzer (3 beeps), and only the latter

option will be activated; the indicator light corresponding to

the activated option will turn on.

Door locked indicator light

When the indicator light is on, the porthole door is locked

to prevent it from being opened; make sure the indicator

light is off before opening the door (wait approximately 3

minutes).

To open the door during a running wash cycle, press the

START/PAUSE button; the door may be opened once the

DOOR LOCKED indicator light turns off.

Starting a wash cycle

Rapid programming

1. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed

the maximum load value indicated in the table of

programmes and wash cycles on the following page.

2. ADD THE DETERGENT. Pull out the detergent

dispenser drawer and pour the detergent into the

relevant compartments as described in “Detergents and

laundry”.

3. CLOSE THE DOOR.

4. Press the “PUSH & WASH” button to start the wash

programme.

Traditional programming

1. Turn the washing machine on by pressing the ON/OFF

button. All the indicator lights will turn on for a few secon-

ds, then only the indicator lights relative to the selected

programme settings will remain lit and the START/PAUSE

indicator light will flash.

2. Load the laundry and close the door.

3. Set the WASH CYCLE knob to the desired programme.

4. Set the washing temperature (see “Personalisation”).

5. Set the spin speed (see “Personalisation”).

6. Measure out the detergent and washing additives (see

“Detergents and laundry”).

7. Select the desired functions.

8. Start the wash cycle by pressing the START/PAUSE

button and the corresponding indicator light will remain lit

in a fixed manner in green.

The display will show the maximum duration of the cycle

chosen, which may decrease after several minutes, since

the effective duration of the programme varies depending

on the wash load and the settings chosen.

To cancel the set wash cycle, pause the machine by pres-

sing the START/PAUSE button and select a new cycle.

9. At the end of the wash cycle the END indicator light

will switch on. The door can be opened once the DOOR

LOCK indicator light turns off (wait approximately 3 mi-

nutes). Take out your laundry and leave the appliance door

ajar to make sure the drum dries completely. Switch the

washing machine off by pressing the ON/OFF button.

Wash cycles

Table of wash cycles

Push & Wash

This function allows for starting a wash cycle even when the machine is switched off without having to press the ON/OFF

button in advance, or after switching on the machine, without having activated any button and/or selector (otherwise, the

Push & Wash function will be deactivated). To start the Push & Wash cycle press and hold the relative button for 2 seconds.

The lit indicator light indicates that the cycle has started. This wash cycle is ideal for cotton or synthetic fabrics, as it washes

at a temperature of 30° and a maximum spin speed of 1000 rpm. Maximum load 3,5 kg. (Cycle duration 45’).

How does it work?

1. Load the laundry (cotton and/or synthetic garments) and close the door.

2. Pour the detergent and additives.

3. Start the programme by pressing and holding the Push & Wash button for 2 seconds. The relative indicator light turns

green and the door will lock (the DOOR LOCKED symbol turns on).

N.B.: starting the wash cycle through the Push & Wash button activates an automatic non-customisable cycle

recommended for cotton and synthetic fabrics. This programme does not allow for setting any additional options.

To open the door while an automatic cycle is under way, press the START/PAUSE button; if the DOOR LOCKED symbol

is switched off the door may be opened. Press the START/PAUSE button again to restart the wash cycle from the point at

which it was interrupted.

4. Once the programme is finished, the END written turns on.

1) Test wash cycle in compliance with regulation 1061/2010: set wash cycle 9 with a temperature of 60°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments

which can be washed at 60°C. The actual washing temperature may differ from the indicated value.

2) Test wash cycle in compliance with regulation 1061/2010: set wash cycle 9 with a temperature of 40°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments

which can be washed at 40°C. The actual washing temperature may differ from the indicated value.

For all Test Institutes:

3) Long wash cycle for cottons: set wash cycle 6 with a temperature of 40°C.

4) Synthetic program along: set wash cycle 7 with a temperature of 40°C.

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-

ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

* If you select programme and exclude the spin cycle, the machine will drain only.

** The duration of the wash cycle can be checked on the display.

Wash cycles

Description of the wash cycle

Max.

temp.

(°C)

Max.

speed

(rpm)

Detergents

Max. load (kg)

Residual

dampness %

Energy

consumption kWh

Total water lt

Cycle duration

Wash

Fabric

softener

Everyday 30° ECO

Daily cotton 30° 1200

 

3.5 - - - **

Daily synthetics 30° 1000

 

3.5 - - - **

Coloureds 30° 1000

 

3.5 - - - **

Delicates 30° 0   1 - - - **

Rapid 30min: to refresh lightly soiled garments quickly (not suitable

for wool, silk and clothes which require washing by hand). 30° 800

 

3.5 70 0.16 33 30’

Traditionals

Cotton (3): lightly soiled whites and delicate colours. 40°

(Max.60°) 1400

 

7 53 0.97 75 220’

Synthetics (4): lightly soiled resistant colours. 40°

(Max.60°) 1000

 

3.5 46 0.68 55 120’

Mixed 40° 1400

 

7 - - - **

Eco cotton 60°C (1): heavily soiled whites and resistant colours. 60° 1400

 

7 53 0.99 52.4 265’

Eco cotton 40°C (2): lightly soiled whites and delicate colours. 40° 1400

 

7 53 0.97 75 220’

White cotton: extremely soiled whites. 90° 1400

 

7 - - - **

Specials

Sport 30° 600

 

3.5 - - - **

Duvet: for down-stuffed garments. 30° 1000

 

2 - - - **

Wool: for wool, cashmere, etc. 40° 800

 

1.5 - - - **

Anti odour 40° 1000

 

3 - - - **

Rinse + Spin - 1400

-

7 - - - **

Spin + Drain - 1400

- -

7 - - - **

Drain only * -

- -

7 - - - **

Setting the temperature

Turning the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).

The temperature may be lowered, or even set to a cold wash .

N.B.: If the set value is compatible with the selected cycle, the knob indicator will be lit (fixed light). If it isn’t, it will flash and 3

beeps will be heard.

The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value

set for each wash cycle.

! Exception: if the 6 programme is selected, the temperature can be increased up to a value of 60°C.

! Exception: if the 7 programme is selected, the temperature can be increased up to a value of 60°C.

Setting the spin speed

Turning the SPIN SPEED knob to set the spin speed for the selected wash cycle.

N.B.: If the set value is compatible with the selected cycle, the knob indicator will be lit (fixed light). If it isn’t, it will flash and 3

beeps will be heard.

The maximum spin speeds available for each wash cycle are as follows:

Wash cycles Maximum spin speed

Cottons 1400 rpm

Synthetics 1000 rpm

Wool 800 rpm

The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol .

The washing machine will automatically prevent you from selecting a spin speed which is higher than the maximum speed

set for each wash cycle.

Functions

The various wash functions available with this washing machine will help to achieve the desired results, every time.

To activate the functions:

1. Press the button corresponding to the desired function;

2. the function is enabled when the corresponding indicator light is illuminated.

Note:

- If the selected function is not compatible with the programmed wash cycle, the corresponding indicator light will flash and

the function will not be activated.

- If the selected option is not compatible with another previously selected option, the indicator light will flash accompanied

by a buzzer (3 beeps), and only the latter option will be activated; the indicator light corresponding to the activated option

will turn on.

Stain removal

This option allows for selecting the type of dirt so as to optimally adjust the cycle for removing the stains. The following types

of dirt can be selected:

- Food, for stains caused by foodstuffs and beverages, for example.

- Work, for grease and ink stains, for example.

- Outdoor, for mud and grass stains, for example.

! The wash cycle duration varies according to the type of selected dirt.

Extra Rinse

By selecting this option, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is particularly

useful for sensitive skin.

Easy iron

By selecting this function, the wash and spin cycles will be modified in order to reduce the formation of creases. At the end

of the cycle the washing machine will perform slow rotations of the drum, while the EASY IRON and START/PAUSE indicator

lights will flash. To end the cycle, press the START/PAUSE button or the EASY IRON button.

Personalisation

Detergents and laundry

Detergent dispenser drawer

Successful washing results also depend on the correct dose

of detergent: adding too much detergent will not necessarily

result in a more efficient wash, and may in fact cause build

up on the inside of your appliance and contribute to envi-

ronmental pollution.

! Do not use hand washing detergents because these create

too much foam.

! Use powder detergent for white cotton garments, for pre-

washing, and for washing at temperatures over 60°C.

! Follow the instructions given

on the detergent packaging.

Open the detergent dispenser

drawer and pour in the deter-

gent or washing additive, as

follows.

Compartment 1: Do not

pour detergent into the middle

compartment 1.

Compartment 2: Washing

detergent (powder or liquid)

If liquid detergent is used, it is recommended that the remo-

vable plastic partition A (supplied) be used for proper dosage.

If powder detergent is used, place the partition into slot B.

Compartment 3: Additives (fabric softeners, etc.)

The fabric softener must not exceed the “max” level indicated

on the central pin.

Preparing the laundry

• Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from whites.

• Empty all garment pockets and check the buttons.

• Do not exceed the values listed in the “Table of wash

cycles”, which refer to the weight of the laundry when dry.

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1.200 g

1 towel 150-250 g

Garments requiring special care

Daily cotton: a 30°C cycle for cotton garments. It allows

for reducing consumption of energy for heating the water,

while guaranteeing excellent results. Suitable for lightly soiled

garments.

Daily synthetics: a 30°C cycle for synthetic garments. It

allows for reducing consumption of energy for heating the

water, while guaranteeing excellent results. Suitable for lightly

soiled garments.

Coloureds: a 30°C cycle that helps to preserve the colours;

suitable for coloured cotton and synthetic garments. It allows

for reducing consumption of energy for heating the water,

while guaranteeing excellent results. Suitable for lightly soiled

garments.

Delicates: use programme 4 to wash very delicate

garments. It is advisable to turn the garments inside out

before washing them. For best results, use liquid detergent

on delicate garments. For washing Silk items and Curtains,

select the relevant cycle 4 and activate the option ;

the machine will end the cycle with the laundry soaked and

the indicator light will flash. To drain the water so that the

laundry can be removed, press the START/PAUSE button

or the option .

Mixed: a 40°C cycle for washing cotton and synthetic

garments together. Suitable for lightly soiled underwear.

Sport (programme 11) is designed for washing lightly soiled

sports clothing (tracksuits, shorts, etc.); for best results, we

recommend not exceeding the maximum load indicated in the

“Programme table”. We recommend using liquid detergent,

and adding the amount suitable for a half-load.

Duvet: to wash single duvets (the weight of which should not

exceed 2 kg), cushions or clothes padded with goose down

such as puffa jackets, use the special wash programme num-

ber 12. We recommend that duvets are placed in the drum

with their edges folded inwards (see figure) and that no more

than ¾ of the total volume of the drum is used. To achieve the

best results, we recommend that a liquid detergent is used

and placed inside the detergent dispenser drawer.

Wool - Woolmark Apparel Care - Blue:

the wool wash cycle of this machine has been approved by

The Woolmark Company for the washing of wool garments

labelled as “hand wash” provided that the products are

washed according to the instructions on the garment label

and those issued by the manufacturer of this washing

machine. (M1126)

In UK, Eire, Hong Kong and India the Woolmark trade mark

is a Certification trade mark.

Anti odour: use programme 14 (Synthetics) for washing

garments with bad odours (e.g. smoke, sweat, fried food).

The programme is designed to remove bad odours while

preserving the fabric fibres.

Troubleshooting

Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure

that the problem cannot be solved easily using the following list.

Problem:

The machine does not switch on.

The wash cycle does not start.

The washing machine does not

take in water (“H2O” will flash on

the display).

The machine continuously fills with

water and continually drains away

or Water left in the drum

or Stuck on wash.

The machine does not drain or spin

- ( error lights flashing ).

The machine does spin.

The machine does not heat or poor

wash results.

The machine does not drain or spin

- & ‘START/PAUSE’ indicator

lights flash.

The programme takes too long.

The machine vibrates a lot during

the spin cycle.

Possible causes / Solutions:

• The appliance is not plugged into the socket fully, or not enough to make contact.

• There is no power to the socket, or the fuse has blown in the mains plug.

• The door is not closed properly.

• The ON/OFF button has not been pressed.

• The START/PAUSE button has not been pressed.

• The water tap has not been turned on to allow water to flow into the machine.

• A delayed start has been set.

• The water inlet hose is kinked.

• The water inlet hose is not connected to the water supply.

• The water pressure is too low.

• The water tap has not been turned on to allow water to flow into the machine.

• There is no water supply to the house.

• The inlet valve filter is blocked.

• The START/PAUSE button has not been pressed.

• The top of the drain hose is too low - It must be fitted at a height between 65

and 100 cm from the floor (see “Installation”).

• The drain hose is connected incorrectly to the sink trap allowing water to run

into the machine, the drain hose must be positioned higher than the bottom of

the sink to prevent water flowing down the drain hose.

• The end of the drain hose has been pushed too far down the standpipe, the

‘U’ bracket should be fitted 100 mm from the end of the drain hose.

• The Pump filter is blocked.

• The drain hose is kinked (see “Installation”).

• New Installation - The blanking cap or spigot has not been removed if

connected under a sink.

• The drain hose or sink trap is blocked.

• The Spin Speed is set to .

• The Temperature is set to .

• If the option is enabled, at the end of the program the machine drum will

rotate slowly. To complete the program press the ‘START/PAUSE’ or the

buttons.

• Programme times will vary due to water pressure, the incoming water tempera-

ture and if the wash load goes out of balance. This will increase the programme

times accordingly (see ‘ The machine wont spin properly’ next page).

• The feet have not been adjusted, enabling the machine to rock.

• New Installation - Either the Transit Bolts including the plastic spacers, or the

Polystyrene Packaging have not been removed when installing the machine.

• The machine is trapped between cabinets and/or walls.

• The load is in a slight out of balance condition and machine is spinning, but at

a lower speed.

Remember, you will be charged for a service call for problems caused by incorrect installation, as indica-

ted on pages 2 to 4.

Not emptying contents from pockets may cause pump or drain blockages, or may damage the machine.

Do not wash items which do not have a wash label, or wash items that are not intended as machine

washable.

The machine is noisy.

The machine wont spin properly.

The machine leaks from the

dispenser.

The machine leaks (other than

dispenser).

The option lights and the START/

PAUSE indicator light are flash

rapidly and an error code appears

on the display (eg F-01, F-..).

The machine smells.

The machine door cannot be

opened.

Door Seal damaged at the bottom.

The water level is too low when

the machine is washing.

There is too much foam.

After completing the programme,

or before starting a programme,

the machine has turned itself off

(no lights).

General.

• There will always be some motor, pump and drum noise during spin.

• Out of Balance detected when attempting to go into a spin cycle - If this

happens the machine will continue to try to repeat the distribution of the load

required before the machine will go into higher spin speeds - This will increase

the programme time accordingly. This is a safety feature to prevent damage.

Out of Balance can be caused by washing a single heavy item (eg duvet, quilt,

etc). - Try the programme again using a different load.

• The dispenser drawer is blocked with detergent and requires cleaning.

• The water pressure is too high and requires turning down - turn down the tap

on the water supply pipe slightly and try again.

• The machine is tilting forwards - It must be level when in its final position.

• The fill hose is loose, check both the cabinet and tap ends.

• The fill hose is tight but still leaks, if so replace the rubber washers, or the fill

hose is missing the rubber washer.

• The drain hose is not fixed in properly.

• Switch off the machine and unplug it, wait for approximately 1 minute and then

switch back on again. If the problem persists contact Technical Assistance

Centre.

• The machine requires a service wash. Run a “Auto Clean” wash cycle with

detergent and no laundry.

• The door will not open until the door lock indicator light goes out shortly after

the program has finished.

• If there is no power to the machine you need to perform the manual unlocking

procedure.

• The door seal has drainage holes at the bottom - This is normal.

• The water level is correct if it can be seen at the bottom of the door.

• The detergent is not suitable for machine washing (it should display the text

‘for washing machines’ or ‘hand and machine wash’ or the like).

• Too much detergent was used - less detergent is required in soft water.

• To comply with new energy saving regulations the machine is fitted with an

automatic standby system. Press ‘ON/OFF’ button for 3 seconds to activate

the machine, it can then either be switched off or a new programme selected.

• Your washing machine contains sensors that monitor progress during the wash

cycle (eg: Water Levels, Temperatures, Out of Balance loads, Wash time/progress).

Normally, if your machine successfully completes the cycle, there is unlikely to

be anything wrong!

Product Guarantee and

Repair Information

Guarantee

12 Months Parts and Labour Guarantee

Your appliance has the benefit of our manufacturer’s

guarantee, which covers the cost of breakdown

repairs for twelve months from the date of purchase.

This gives you the reassurance that if, within that

time, your appliance is proven to be defective

because of either workmanship or materials, we will,

at our discretion, either repair or replace the appliance

at no cost to you:

This guarantee is subject to the following conditions:

- The appliance has been installed and operated

correctly and in accordance with our operating and

maintenance instructions.

- The appliance is used only on the electricity or gas

supply printed on the rating plate.

- The appliance has been used for normal domestic

purposes only.

- The appliance has not been altered, serviced,

maintained, dismantled, or otherwise interfered with

by any person not authorised by us.

- Any repair work must be undertaken by us or our

appointed agent.

- Any parts removed during repair work or any

appliance that is replaced become our property.

- The appliance is used in the United Kingdom or

Republic of Ireland.

The guarantee does not cover:

- Damage resulting from transportation, improper

use, neglect or interference or as a result of improper

installation.

- Replacement of any consumable item or accessory.

These include but are not limited to: plugs, cables,

batteries, light bulbs, fluorescent tubes and starters,

covers and filters.

- Replacement of any removable parts made of glass

or plastic.

THIS GUARANTEE WILL NOT APPLY IF THE

APPLIANCE HAS BEEN USED IN COMMERCIAL

OR NON-DOMESTIC PREMISES.

Recycling and Disposal Information

As part of Indesit’s continued commitment to

helping the environment, Indesit reserves the right

to use quality, recycled components to keep down

customer costs and minimise material wastage.

Please dispose of packaging and old appliances

carefully. To minimise the risk of injury to children,

remove the door, plug, and cut the mains cable

off flush with the appliance. Dispose of these parts

separately to ensure that the appliance can no longer

be plugged into mains socket, and the door cannot

be locked shut.

Repairs and After Sales

For product help and advice, repairs, spare parts or

accessories, we’re here to help.

For local repair engineers - 03448 111 606

ROI - 0818 313 413

UK standard local rate applies

ROI local Irish rate applies

For Parts and Accessories visit:

parts.indesit.co.uk/shop

Please remember to register your appliance at

www.indesitservice.co.uk to activate your 10 year

parts guarantee.

How to find your model and serial number:

195151812.00

10/2016

Indesit Company Spa

Viale Aristide Merloni, 47

60044 Fabriano (AN)

Italy