Table of Contents
Indesit IWC 81481 ECO UK.M User Manual
Displayed below is the user manual for IWC 81481 ECO UK.M by Indesit which is a product in the Washing Machines category. This manual has pages.
Related Manuals
GB
1
Contents
Installation, 2-3-4-5
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 6
Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 7
General safety
Disposal
Description of the washing machine
and starting a wash cycle, 8-9
Control panel
Indicator lights
Starting a wash cycle
Wash cycles, 10
Table of wash cycles
Personalisation, 11
Setting the temperature
Setting the spin speed
Functions
Detergents and laundry, 12
Detergent dispenser drawer
Preparing the laundry
Garments requiring special care
Load balancing system
Troubleshooting, 13-14
Product Guarantee and Repair Informa-
tion, 15
IWC 81481
Instructions for use
WASHING MACHINE
English,1
GB
،يبرع,16
يبرع
2
GB
Installation
! Keep this instruction manual in a safe place for
future reference. Should the appliance be sold, tran-
sferred or moved, make sure the instruction manual
accompanies the washing machine to inform the
new owner as to its operation and features.
! Read these instructions carefully: they contain
vital information on installation, use and safety.
Unpacking and levelling
Unpacking
1. Unpack the washing machine.
2. Check whether the washing machine has
been damaged during transport. If this is the
case, do not install it and contact your retailer.
3. Remove the 3 pro-
tective screws and the
rubber bush with the
respective spacer, si-
tuated on the rear of
the appliance (see also
the installation leaflet).
4. Seal the gaps using the plastic plugs provided.
5. Keep all the parts: you will need them again
if the washing machine needs to be moved to
another location.
! Packaging materials are not children’s toys.
Levelling
Your machine may make a considerable amount
of noise if the two front feet have not been adju-
sted correctly.
1. Install the washing machine on a flat sturdy
floor, without resting it up against walls, furniture
cabinets or other.
2. If the floor is not per-
fectly level, compensate
for any unevenness by
tightening or loosening
the adjustable front feet
(see figure); the angle
of inclination, measu-
red according to the
worktop, must not ex-
ceed 2°.
Levelling your appliance
correctly will provide it with stability and avoid any
vibrations, noise and shifting during operation. If
it is placed on a fitted or loose carpet, adjust the
feet in such a way as to allow enough room for
ventilation beneath the washing machine.
Electric and water connections
Connecting the water inlet hose
1. Connect the supply
pipe by screwing it to
a cold water tap using
a 3/4 gas threaded
connection (see figure).
Before performing the
connection, allow the
water to run freely until
it is perfectly clear.
2. Connect the other
end of the water inlet
hose to the washing
machine, screwing it
onto the appliance’s
cold water inlet, situated
on the top right-hand
side on the rear of the
appliance (see figure).
3. Make sure there are no kinks or bends in the
hose.
! The water pressure at the tap must be within
the values indicated in the Technical details
table (on the page 5).
! If the water inlet hose is not long enough,
contact a specialist store or an authorised
serviceman.
! Ensure that the supply taps are allowing wa-
ter through. Old taps may seize in the closed
position and thus prevent water reaching the
machine.
GB
3
Connecting the drain hose
Connect the drain
hose, without bending
it, to a draining duct or
a wall drain situated
between 65 and 100
cm from the floor;
The drain hose may
be connected to an
under-sink trap. Be-
fore connecting the
drain hose from the
machine ensure that
any blanks or remo-
vable ends have been
taken off the spigot.
If it is placed over the
edge of a basin or sink
be sure the free end of
the hose should not
be underwater.
! We advise against the use of hose extensions; in
case of absolute need, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length. Ensure that if the drain
hose is pushed into a standpipe, that the end does
not go down more than 15cms (6 inches). If the hose
is pushed down too far, this may cause the machine
to self -syphon ie. continuously empty as it is filling.
Electric connection
Before plugging the appliance into the mains
socket, make sure that:
• the socket is earthed and in compliance with
the applicable law;
• the socket is able to sustain the appliance’s
maximum power load indicated on the Technical
Data Plate fixed on the machine;
65 - 100 cm
Where it connects to
the waste water pipe
cut end off spigot or
remove the blanking cap
• the supply voltage is included within the values
indicated on the Technical Data Plate fixed on
the machine.
• the socket is compatible with the washing
machine’s plug. If this is not the case, replace
the socket or the plug.
Your appliance is now supplied with a 13 amp fu-
sed plug it can be plugged into a 13 amp socket
for immediate use. Before using the appliance
please read the instructions below.
WARNING - THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA
approved fuse to BS 1362 should always be
used, and the fuse cover re-fitted. If the fuse
cover is lost, the plug must not be used until a
replacement is obtained.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of
the correct colour as indicated by the coloured
marking or the colour that is embossed in words
on the base of the plug. Replacements can be
obtained directly from your nearest Service Depot.
Removing the plug:
If your appliance has a non-rewireable moulded
plug and you should wish to re-route the mains
cable through partitions, units etc., please en-
sure that either:
the plug is replaced by a fused 13 ampere rewi-
reable plug bearing the BSI mark of approval.
or:
the mains cable is wired directly into a 13 amp
cable outlet, controlled by a switch, (in complian-
ce with BS 5733) which is accessible without
moving the appliance.
Disposing of the plug:
Ensure that before disposing of the plug itself,
you make the pins unusable so that it cannot be
accidentally inserted into a socket.
Instructions for connecting cable to an alterna-
tive plug:
Important: the wires in the mains lead are co-
loured in accordance with the following code:
Green & Yellow Earth
Blue Neutral
Brown Live
4
GB
As the colours of the wires in the lead may not
correspond with the coloured markings iden-
tifying the terminals in your plug, proceed as
follows:
Connect Green & Yellow wire to terminal
marked E or or coloured Green or Green &
Yellow.
Connect Brown wire to terminal marked L or
coloured Red.
Connect Blue wire to terminal marked N or co-
loured Black.
If a 13 amp plug (BS 1363) is used it must be
fitted with a 13 amp fuse, either in the plug or
adaptor or at the distribution board.
If you are in any doubt regarding the electrical
supply to your machine, consult a qualified
electrician before use.
How to connect an alternative plug:
The wires in this mains lead are coloured in
accordance with the following code:
BLUE NEUTRAL (N)
BROWN LIVE (L)
GREEN & YELLOW EARTH (E)
Disposing of the appliance:
When disposing of the appliance please re-
move the plug by cutting the mains cable as
close as possible to the plug body and dispo-
se of it as described above.
! The washing machine should not be installed
in an outdoor environment, not even where
the area is sheltered, because it may be very
dangerous to leave it exposed to damp, rain
and thunderstorms.
! When the washing machine is installed, the
mains socket must be within easy reach.
! Do not use extensions or multiple sockets.
! The power supply cable must never be bent
or dangerously compressed.
! The power supply cable must only be repla-
ced by an authorised serviceman.
Warning! The company denies all liability if and
when these norms are not respected.
The first wash cycle
Once the appliance has been installed, and
before you use it for the first time, run a wash
cycle with detergent and no laundry, using the
wash cycle 1.
GREEN &
YELLOW
BROWN
BLUE
13 ampere fuse
CROSS-BAR
CORD GRIP
Technical data
Model IWC 81481
Dimensions
width 59.5 cm
height 85 cm
depth 57.2 cm
Capacity from 1 to 8 kg
Electrical
connections
please refer to the technical
data plate fixed to the machine
Water
connection
maximum pressure
1 MPa (10 bar)
minimum pressure
0.05 MPa (0.5 bar)
drum capacity 54 litres
Spin speed up to 1400 rotations per minute
Test wash
cycles in
accordan-
ce with re-
gulations
1061/2010
and
1015/2010
Programme 2:
Cotton Standard 60°.
Programme 3:
Cotton Standard 40°.
This appliance conforms to
the following EC Directives:
- 2004/108/EC (Electroma-
gnetic Compatibility)
- 2012/19/EU - WEEE
- 2006/95/EC Low Voltage)
GB
5
6
GB
Care and maintenance
Cutting off the water and electri-
city supplies
• Turn off the water tap after every wash cycle.
This will limit wear on the hydraulic system
inside the washing machine and help to pre-
vent leaks.
• Unplug the washing machine when cleaning
it and during all maintenance work.
Cleaning the washing machine
The outer parts and rubber components of the
appliance can be cleaned using a soft cloth
soaked in lukewarm soapy water. Do not use
solvents or abrasives.
Cleaning the detergent dispenser
drawer
Remove the dispenser
by raising it and pul-
ling it out (see figure).
Wash it under running
water; this operation
should be repeated
frequently.
Caring for the door and drum of
your appliance
• Always leave the porthole door ajar in order
to prevent unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cle-
aning pump which does not require any main-
tenance. Sometimes, small items (such as
coins or buttons) may fall into the pre-chamber
which protects the pump, situated in its bot-
tom part.
! Make sure the wash cycle has finished and
unplug the appliance.
To access the pre-
chamber:
1. using a screwdri-
ver, remove the cover
panel on the lower
front part of the wa-
shing machine (see
figure);
2. unscrew the lid
by rotating it anti-
clockwise (see figu-
re): a little water may
trickle out. This is
perfectly normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks
are securely in place before you push it onto
the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If
there are any cracks, it should be replaced
immediately: during the wash cycles, water
pressure is very strong and a cracked hose
could easily split open.
! Never use second-hand hoses.
GB
7
Precautions and tips
Consumers should contact their local authority or retailer
for information concerning the correct disposal of their
old appliance.
! This washing machine was designed and constructed in
accordance with international safety regulations. The fol-
lowing information is provided for safety reasons and must
therefore be read carefully.
General safety
• This appliance was designed for domestic use only.
• This appliance can be used by children aged
from 8 years and above and persons with re-
duced physical, sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved. Chil-
dren shall not play with the appliance. Clea-
ning and user maintenance shall not be made
by children without supervision.
• Do not touch the machine when barefoot or with wet or
damp hands or feet.
• Do not pull on the power supply cable when unplugging
the appliance from the electricity socket. Hold the plug
and pull.
• Do not open the detergent dispenser drawer while the
machine is in operation.
• Do not touch the drained water as it may reach extreme-
ly high temperatures.
• Never force the porthole door. This could damage the
safety lock mechanism designed to prevent accidental
opening.
• If the appliance breaks down, do not under any circum-
stances access the internal mechanisms in an attempt
to repair it yourself.
• Always keep children well away from the appliance while
it is operating.
• The door can become quite hot during the wash cycle.
• If the appliance has to be moved, work in a group of two
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
• Before loading laundry into the washing machine, make
sure the drum is empty.
Disposal
• Disposing of the packaging materials: observe local
regulations so that the packaging may be re-used.
• The European Directive 2012/19/EU - WEEE on Waste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected separately
in order to optimise the recovery and recycling of the
materials they contain and reduce the impact on human
health and the environment. The crossed out “wheeled
bin” symbol on the product reminds you of your obliga-
tion, that when you dispose of the appliance it must be
separately collected.
8
GB
Detergent dispenser drawer: used to dispense
detergents and washing additives (see “Detergents and
laundry”).
ON/OFF button: switches the washing machine on and off.
WASH CYCLE knob: programmes the wash cycles. Du-
ring the wash cycle, the knob does not move.
FUNCTION buttons with indicator light: used to select the
available functions. The indicator light corresponding to the
selected function will remain lit.
TEMPERATURE knob: sets the temperature or the cold
wash cycle (see “Personalisation”).
SPIN SPEED knob: sets the spin speed or exclude the
spin cycle completely (see “Personalisation”).
WASH CYCLE PROGRESS/DELAY TIMER
indicator
light
s: used to monitor the progress of the wash cycle.
The illuminated indicator light shows which phase is in
progress.
If the Delay Timer function has been set, the time remai-
ning until the wash cycle starts will be indicated (see next
page).
DOOR LOCKED indicator light: indicates whether the
door may be opened or not (see next page).
START/PAUSE button with indicator light: starts or tem-
porarily interrupts the wash cycles.
N.B. To pause the wash cycle in progress, press this
button; the corresponding indicator light will flash orange,
while the indicator light for the current wash cycle phase
will remain lit in a fixed manner. If the DOOR LOCKED
indicator light is switched off, the door may be opened
(wait approximately 3 minutes).
To start the wash cycle from the point at which it was inter-
rupted, press this button again.
Standby mode
This washing machine, in compliance with new energy sa-
ving regulations, is fitted with an automatic standby system
which is enabled after about 30 minutes if no activity is
detected. Press the ON-OFF button briefly and wait for the
machine to start up again.
Description of the washing
machine and starting a wash cycle
WASH CYCLE PROGRESS/
DELAY TIMER indicator lights
DOOR LOCKED
indicator light
START/PAUSE
button with
indicator light
Control panel
Detergent dispenser drawer
ON/OFF
button
WASH CYCLE
knob
TEMPERATURE
knob
FUNCTION
buttons with
indicator lights
SPIN SPEED
knob
GB
9
Indicator lights
The indicator lights provide important information.
This is what they can tell you:
Delayed start
If the DELAY TIMER function has been activated (see “Per-
sonalisation”), after the wash cycle has been started the
indicator light corresponding to the selected delay period
will begin to flash:
As time passes, the remaining delay will be displayed and
the corresponding indicator light will flash:
The set programme will start once the selected time delay
has expired.
Wash cycle phase indicator lights
Once the desired wash cycle has been selected and has be-
gun, the indicator lights switch on one by one to indicate which
phase of the cycle is currently in progress.
Function buttons and corresponding indicator lights
When a function is selected, the corresponding indicator
light will illuminate.
If the selected function is not compatible with the program-
med wash cycle, the corresponding indicator light will flash
and the function will not be activated.
If the selected function is not compatible with another
function which has been selected previously, the indicator
light corresponding to the first function selected will
flash and only the second function will be activated; the
indicator light corresponding to the enabled option will
remain lit.
Door locked indicator light
When the indicator light is on, the porthole door is locked
to prevent it from being opened; make sure the indicator
light is off before opening the door (wait approximately 3
minutes). To open the door during a running wash cycle,
press the START/PAUSE button; the door may be opened
once the DOOR LOCKED indicator light turns off.
Starting a wash cycle
1. Switch the washing machine on by pressing the ON/OFF button. All indicator lights will switch on for a few seconds, then
they will switch off and the START/PAUSE indicator light will pulse.
2. Load the laundry and close the door.
3. Set the WASH CYCLE knob to the desired programme.
4. Set the washing temperature (see “Personalisation”).
5. Set the spin speed (see “Personalisation”).
6. Measure out the detergent and washing additives (see “Detergents and laundry”).
7. Select the desired functions.
8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a fixed man-
ner, in green. To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.
9. At the end of the wash cycle the indicator light will switch on. The door can be opened once the DOOR LOCK indi-
cator light turns off (wait approximately 3 minutes). Take out your laundry and leave the appliance door ajar to make sure the
drum dries completely. Switch the washing machine off by pressing the ON/OFF button.
Wash
Rinse
Spin
Drain
End of wash cycle
10
GB
Wash cycles
Table of wash cycles
Wash cycles
Description of the wash cycle
Max.
temp.
(°C)
Max.
speed
(rpm)
Detergents
Max.
load (kg)
Residual
dampness
%
Energy
consum-
ption kWh
Total water lt
Cycle
duration
Wash Fabric
softener
Daily
1White Cotton: extremely soiled whites. 90° 1400 8 - - - 170’
2Cotton Standard (1): heavily soiled whites and resistant colours. 60° 1400 8 53 1.51 54.7 190’
3Cotton Standard (2-3): lightly soiled whites and delicate colours. 40° 1400 8 53 0.93 82 170’
4Synthetics: heavily soiled resistant colours. 50° 1000 3.5 - - - 125’
4Synthetics (4): lightly soiled resistant colours. 40° 1000 3.5 44 0.49 38 120’
5Mix Colored: lightly soiled whites and delicate colours. 40° 1400 8 - - - 105’
20° Zone
6 Cotton Standard
20°
1400
8 - - - 210’
7 Mix Light
20° 1000
8 - - - 115’
8 20’ Refresh
20° 800
1.5 - - - 20’
Special
9 Outwear
30° 400 -
2 - - - 60’
10 Wool: for wool, cashmere, etc.
40° 800
1.5 - - - 85’
11 Jeans
40° 800
3.5 - - - 80’
Sport
12 Sport Intensive 30° 600 3 - - - 85’
13 Sport Light 30° 600 3 - - - 60’
14 Special Shoes 30° 600 Max. 2
pairs - - - 50’
Partial wash cycles
Rinse - 1400 - 8 - - - 36’
Spin + Drain - 1400 - - 8 - - - 10’
Drain only * - - - 8 - - - 3’
The length of cycle shown in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary
according to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing
and any wash options selected.
For all Test Institutes:
1) Test wash cycle in compliance with regulation 1061/2010: set wash cycle 2 with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be
used for garments which can be washed at 60°C. The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with regulation 1061/2010: set wash cycle 3 with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be
used for garments which can be washed at 40°C. The actual washing temperature may differ from the indicated value.
3) Long wash cycle for cottons: set wash cycle 3 with a temperature of 40°C.
4) Synthetic program along: set wash cycle 4 with a temperature of 40°C.
* If you select programme and exclude the spin cycle, the machine will drain only.
GB
11
Setting the temperature
Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).
The temperature may be lowered, or even set to a cold wash .
The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value
set for each wash cycle.
Setting the spin speed
Turn the SPIN SPEED knob to set the spin speed for the selected wash cycle.
The maximum spin speeds available for each wash cycle are as follows:
Wash cycles Maximum spin speed
Cottons 1400 rpm
Synthetics 1000 rpm
Wool 800 rpm
The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol .
The washing machine will automatically prevent you from selecting a spin speed which is higher than the maximum speed
set for each wash cycle.
Functions
The various wash functions available with this washing machine will help to achieve the desired results, every time.
To activate the functions:
1. Press the button corresponding to the desired function;
2. the function is enabled when the corresponding indicator light is illuminated.
Note:
- If the selected function is not compatible with the programmed wash cycle, the corresponding indicator light will flash and
the function will not be activated.
- If the selected function is not compatible with another function which has been selected previously, the indicator light
corresponding to the first function selected will flash and only the second function will be activated; the indicator light
corresponding to the enabled option will remain lit.
Selecting this option enables you to suitably adjust drum rotation, temperature and water to a reduced load of lightly soiled
cotton and synthetic fabrics (refer to the “
“Table of wash cycles”
). “ ” enables you to wash in less time thereby saving
water and electricity. We suggest using a liquid detergent suitably measured out to the load quantity.
The function saves energy by not heating the water used to wash your laundry - an advantage both to the
environment and to your energy bill. Instead, intensified wash action and water optimisation ensure great wash results in the
same average time of a standard cycle.
For the best washing results we recommend the usage of a liquid detergent.
Extra Rinse
By selecting this option, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is particularly
useful for sensitive skin.
Delay Timer
This timer delays the start time of the wash cycle by up to 12 hours.
Press the button repeatedly until the indicator light corresponding to the desired delay time switches on. The fifth time the button
is pressed, the function will be disabled.
N.B. Once the START/PAUSE button has been pressed, the delay time can only be modified by decreasing it until launching
the set programme.
Personalisation
12
GB
Detergents and laundry
Detergent dispenser drawer
Good washing results also depend on the correct dose of
detergent: adding too much detergent will not necessa-
rily result in a more efficient wash, and may in fact cause
build up on the inside of your appliance and contribute to
environmental pollution.
! Do not use hand washing detergents because these
create too much foam.
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
Open the detergent di-
spenser drawer and pour
in the detergent or washing
additive, as follows.
! Do not pour detergent into the compartment 1.
Detergent should only be poured into the compartment 2.
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
Preparing the laundry
• Divide the laundry according to:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
• Empty all garment pockets and check the buttons.
• Do not exceed the values listed in the “Table of wash
cycles”, which refer to the weight of the laundry when dry.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
12
3
Garments requiring special care
Outwear (wash cycle 9): is studied for washing water-
repellent fabrics and winter jackets (e.g. Gore-Tex, polyester,
nylon); for best results, use a liquid detergent and dosage
suitable for a half-load; pre-treat necks, cuffs and stains if
necessary; do not use softeners or detergents containing
softeners. Stuffed duvets cannot be washed with this pro-
gramme.
Wool: all wool garments can be washed using programme
10, even those carrying the “hand-wash only” label. For
best results, use special detergents and do not exceed 1,5 kg
of laundry.
Jeans: Turn garments inside-out before washing and use a
liquid detergent. Use programme 11.
Sport Intensive (programma 12): is for washing heavily
soiled sports clothing fabrics (tracksuits, shorts, etc.); for
best results, we recommend not exceeding the maximum
load indicated in the “Programme table”.
Sport Light (programma 13): is for washing lightly soiled
sports clothing fabrics (tracksuits, shorts, etc.); for best
results, we recommend not exceeding the maximum load
indicated in the “Programme table”. We recommend using
a liquid detergent and dosage suitable for a half-load.
Special Shoes (programma 14): is for washing sports
shoes; for best results, do not wash more than 2 pairs si-
multaneously.
The 20° wash cycles (Zone 20°) offer effective washing
performance at low temperatures, reducing electricity
usage and expenditure while benefitting the environment.
The 20° wash cycles meet all requirements:
Cotton Standard (programme 6) ideal for lightly soiled
cotton loads. The effective performance levels achieved
at cold temperatures, which are comparable to washing
at 40°, are guaranteed by a mechanical action which
operates at varying speed, with repeated and frequent
peaks.
Mix Light (programme 7) ideal for mixed loads (cotton
and synthetics) with a normal soil level. The effective
performance levels achieved at cold temperatures are
guaranteed by a mechanical action which operates at
varying speed, across set average intervals.
20’ Refresh (programme 8) ideal for refreshing and
washing lightly soiled garments in a few minutes. It lasts
just 20 minutes and therefore saves both time and energy.
It can be used to wash different types of fabrics together
(except for wool and silk), with a maximum load of 1.5 kg.
Load balancing system
Before every spin cycle, to avoid excessive vibrations and
to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the
washing rotation speed. If, after several attempts, the load is
not balanced correctly, the machine spins at a reduced spin
speed. If the load is excessively unbalanced, the washing ma-
chine performs the distribution process instead of spinning.
To encourage improved load distribution and balance, we
recommend small and large garments are mixed in the load.
GB
13
Troubleshooting
Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure
that the problem cannot be solved easily using the following list.
Problem:
The machine does not switch on.
The wash cycle does not start.
The machine does not fill with wa-
ter or the indicator light for the first
wash cycle stage flashes rapidly.
The machine continuously fills with
water and continually drains away
or Water left in the drum
or Stuck on wash.
The machine does not drain or
spin.
The machine does not heat or poor
wash results.
The programme takes too long.
The machine vibrates a lot during
the spin cycle.
Possible causes / Solutions:
• The appliance is not plugged into the socket fully, or not enough to make contact.
• There is no power to the socket, or the fuse has blown in the mains plug.
• The door is not closed properly.
• The ON/OFF button has not been pressed.
• The START/PAUSE button has not been pressed.
• The water tap has not been turned on to allow water to flow into the machine.
• A delayed start has been set.
• The water inlet hose is kinked.
• The water inlet hose is not connected to the water supply.
• The water pressure is too low.
• The water tap has not been turned on to allow water to flow into the machine.
• There is no water supply to the house.
• The inlet valve filter is blocked.
• The START/PAUSE button has not been pressed.
• The top of the drain hose is too low - It must be fitted at a height between 65
and 100 cm from the floor (see “Installation”).
• The drain hose is connected incorrectly to the sink trap allowing water to run
into the machine, the drain hose must be positioned higher than the bottom of
the sink to prevent water flowing down the drain hose.
• The end of the drain hose has been pushed too far down the standpipe, the
‘U’ bracket should be fitted 100 mm from the end of the drain hose.
• The Pump filter is blocked.
• The drain hose is kinked (see “Installation”).
• New Installation - The blanking cap or spigot has not been removed if
connected under a sink.
• The drain hose or sink trap is blocked.
• The wash cycle does not include draining, some wash cycles require the drain
phase to be started manually.
• The ‘Spin Speed’ selector knob is in the position.
• The ‘Temperature’ selector knob is in the “ ” position.
• Programme times will vary due to water pressure, the incoming water tempera-
ture and if the wash load goes out of balance. This will increase the programme
times accordingly (see ‘ The machine wont spin properly’ next page).
• The feet have not been adjusted, enabling the machine to rock.
• New Installation - Either the Transit Bolts including the plastic spacers, or the
Polystyrene Packaging have not been removed when installing the machine.
• The machine is trapped between cabinets and/or walls.
• The load is in a slight out of balance condition and machine is spinning, but at
a lower speed.
14
GB
The machine is noisy.
The machine wont spin properly.
The machine leaks from the
dispenser.
The machine leaks (other than
dispenser).
The indicator lights on the console
are flashing rapidly.
The machine smells.
The machine door cannot be
opened.
Door Seal damaged at the bottom.
The water level is too low when
the machine is washing.
There is too much foam.
After completing the programme,
or before starting a programme,
the machine has turned itself off
(no lights).
General.
• There will always be some motor, pump and drum noise during spin.
• Out of Balance detected when attempting to go into a spin cycle - If this
happens the machine will continue to try to repeat the distribution of the load
required before the machine will go into higher spin speeds - This will increase
the programme time accordingly. This is a safety feature to prevent damage.
Out of Balance can be caused by washing a single heavy item (eg duvet, quilt,
etc). - Try the programme again using a different load.
• The dispenser drawer is blocked with detergent and requires cleaning.
• The water pressure is too high and requires turning down - turn down the tap
on the water supply pipe slightly and try again.
• The machine is tilting forwards - It must be level when in its final position.
• The fill hose is loose, check both the cabinet and tap ends.
• The fill hose is tight but still leaks, if so replace the rubber washers, or the fill
hose is missing the rubber washer.
• The drain hose is not fixed in properly.
• Switch off the machine and unplug it, wait for approximately 1 minute and then
switch it back on again If the problem persists contact the Technical Assistance
Service.
• The machine requires a service wash. Run a n° 1 wash cycle with detergent
and no laundry.
• The door will not open until the door lock indicator light goes out shortly after
the program has finished.
• The door seal has drainage holes at the bottom - This is normal.
• The water level is correct if it can be seen at the bottom of the door.
• The detergent is not suitable for machine washing (it should display the text
‘for washing machines’ or ‘hand and machine wash’ or the like).
• Too much detergent was used - less detergent is required in soft water.
• To comply with new energy saving regulations the machine is fitted with an
automatic standby system. Press ‘ON/OFF’ button for 3 seconds to activate
the machine, it can then either be switched off or a new programme selected.
• Your washing machine contains sensors that monitor progress during the wash
cycle (eg: Water Levels, Temperatures, Out of Balance loads, Wash time/pro-
gress).
Normally, if your machine successfully completes the cycle, there is unlikely to
be anything wrong!
Remember, you will be charged for a service call for problems caused by incorrect installation, as indica-
ted on pages 2 to 4.
Not emptying contents from pockets may cause pump or drain blockages, or may damage the machine.
Do not wash items which do not have a wash label, or wash items that are not intended as machine wa-
shable.
GB
15
Product Guarantee and
Repair Information
Guarantee
12 Months Parts and Labour Guarantee
Your appliance has the benefit of our manufacturer’s
guarantee, which covers the cost of breakdown
repairs for twelve months from the date of purchase.
This gives you the reassurance that if, within that
time, your appliance is proven to be defective
because of either workmanship or materials, we will,
at our discretion, either repair or replace the appliance
at no cost to you:
This guarantee is subject to the following conditions:
- The appliance has been installed and operated
correctly and in accordance with our operating and
maintenance instructions.
- The appliance is used only on the electricity or gas
supply printed on the rating plate.
- The appliance has been used for normal domestic
purposes only.
- The appliance has not been altered, serviced,
maintained, dismantled, or otherwise interfered with
by any person not authorised by us.
- Any repair work must be undertaken by us or our
appointed agent.
- Any parts removed during repair work or any
appliance that is replaced become our property.
- The appliance is used in the United Kingdom or
Republic of Ireland.
The guarantee does not cover:
- Damage resulting from transportation, improper
use, neglect or interference or as a result of improper
installation.
- Replacement of any consumable item or accessory.
These include but are not limited to: plugs, cables,
batteries, light bulbs, fluorescent tubes and starters,
covers and filters.
- Replacement of any removable parts made of glass
or plastic.
THIS GUARANTEE WILL NOT APPLY IF THE
APPLIANCE HAS BEEN USED IN COMMERCIAL
OR NON-DOMESTIC PREMISES.
Recycling and Disposal Information
As part of Indesit’s continued commitment to
helping the environment, Indesit reserves the right
to use quality, recycled components to keep down
customer costs and minimise material wastage.
Please dispose of packaging and old appliances
carefully. To minimise the risk of injury to children,
remove the door, plug, and cut the mains cable
off flush with the appliance. Dispose of these parts
separately to ensure that the appliance can no longer
be plugged into mains socket, and the door cannot
be locked shut.
Repairs and After Sales
For product help and advice, repairs, spare parts or
accessories, we’re here to help.
For local repair engineers - 03448 111 606
ROI - 0818 313 413
UK standard local rate applies
ROI local Irish rate applies
For Parts and Accessories visit:
parts.indesit.co.uk/shop
Please remember to register your appliance at
www.indesitservice.co.uk to activate your 10 year
parts guarantee.
How to find your model and serial number:
16
GB
AR
30-31-32-33
40
AR
34-33-32-31
41
34-33-32
26
41
IWC 81481
20-19-18
22-21
23
24
25
27
28
29
AR
!
!
1
2
43
4
5
!
1
2
1
2
3
!
!
!
!
3
AR
71
اوﺻﻠﻮا ﺧﺮﻃﻮم ﺗﻔﺮﻳﻎ اﻟﻤﺎء ﻣﻦ ﺣﻮض
ﻏ
ـ
ﺴ
ـ
ﻴ
ـ
ﻞ اﻟ
ـ
ﻐ
ـ
ﺴ
ـ
ﺎﻟ
ـ
ﺔ ﺑ
ـ
ﺪون ﻃ
ـ
ﻮﻳ
ـ
ﻪ، ﺑ
ـ
ﻤ
ـ
ﺎﺳ
ـ
ﻮرة
ﺻ
ـ
ﺮف ﻟ
ـ
ﻠ
ـ
ﻤ
ـ
ﺎء، أو ﺑ
ـ
ﻤ
ـ
ﺼ
ـ
ﺮف ﻣ
ـ
ﻮﺟ
ـ
ﻮد ﻓ
ـ
ﻲ
اﻟﺤﺎﺋﻂ ﻋﻠﻰ أن ﻳﻜﻮن ارﺗﻔﺎﻋﻪ ﻣﺎ ﺑﻴﻦ 56
و 001 ﺳﻨﺘﻤﺘﺮ ﻋﻦ ﺳﻄﺢ اﻷ رض
أو ﻗ
ـ
ﻮﻣ
ـ
ﻮا ﺑ
ـ
ﻮﺿ
ـ
ﻌ
ـ
ﻪ ﻋ
ـ
ﻠ
ـ
ﻰ ﺣ
ـ
ﺎﻓ
ـ
ﺔ ﻣ
ـ
ﻐ
ـ
ﺴ
ـ
ﻠ
ـ
ﺔ
أو ﺣ
ـ
ﻮض ﺣ
ـ
ﻤ
ـ
ﺎم، ارﺑ
ـ
ﻄ
ـ
ﻮا اﻟ
ـ
ﺨ
ـ
ﺮﻃ
ـ
ﻮم
ﺑ
ـ
ﺤ
ـ
ﺎﻣ
ـ
ﻞ اﻟ
ـ
ﺨ
ـ
ﺮﻃ
ـ
ﻮم اﻟ
ـ
ﺬي ﻳ
ـ
ﻜ
ـ
ﻮن ﻣ
ـ
ﺰود ﻣ
ـ
ﻊ
اﻟﺠﻬﺎزﺑﻤﺤﺒﺲ اﻟﻤﺎء )اﻧﻈﺮ اﻟﻰ اﻟﺸﻜﻞ(
اﻟﻄﺮف اﻟﺤﺮ ﻣﻦ اﻟﺨﺮﻃﻮم ﻳﺠﺐ أن ﻻ
ﻳﻜﻮن ﻣﻐﻤﻮر ﻓﻲ اﻟﻤﺎء.
ﻏﻴﺮ ﻣﻨﺼﻮح اﺳﺘﺨﺪام ﺧﺮاﻃﻴﻢ ﺗﻄﻮﻳﻞ ، اذا آﺎن ﻣﻦ اﻟﻀﺮوري اﺳﺘﺨﺪام ﺧﺮاﻃﻴﻢ
اﻟ
ـ
ﺘ
ـ
ﻄ
ـ
ﻮﻳ
ـ
ﻞ ﻳ
ـ
ﺠ
ـ
ﺐ أن ﻳ
ـ
ﻜ
ـ
ﻮن ﻗ
ـ
ﻄ
ـ
ﺮ ه
ـ
ﺬا اﻟ
ـ
ﺨ
ـ
ﺮﻃ
ـ
ﻮم ﻧ
ـ
ﻔ
ـ
ﺲ ﻗ
ـ
ﻄ
ـ
ﺮ اﻟ
ـ
ﺨ
ـ
ﺮﻃ
ـ
ﻮم اﻟ
ـ
ﺮﺋ
ـ
ﻴ
ـ
ﺴ
ـ
ﻲ وﻳ
ـ
ﺠ
ـ
ﺐ
أن ﻻ ﻳﺰﻳﺪ ﻃﻮﻟﻪ ﻋﻦ 051 ﺳﻨﺘﻤﺘﺮ.
اﻟﺘﻮﺻﻴﻞ ﺑﺸﺒﻜﺔ اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ
ﻗﺒﻞ ادﺧﺎل ﻗﺎﺑﺲ اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ )اﻟﺬآﺮ( ﺑﻤﻘﺒﺲ اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ )اﻷ ﻧﺜﻰ( ﺗﺄآﺪوا
ﻣﻦ أن:
ﻣﻘﺒﺲ اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ )اﻷ ﻧﺜﻰ( ﻟﻬﺎ ﺧﻂ أرض ﻓﻌﺎل وﺧﺎﺿﻊ اﻟﻰ اﻟﻘﻮاﻧﻴﻦ
ﻣ
ـ
ﻘ
ـ
ﺒ
ـ
ﺲ اﻟ
ـ
ﺘ
ـ
ﻴ
ـ
ﺎر اﻟ
ـ
ﻜ
ـ
ﻬ
ـ
ﺮﺑ
ـ
ﺎﺋ
ـ
ﻲ )اﻷ ﻧ
ـ
ﺜ
ـ
ﻰ( ﻗ
ـ
ﺎدر ﻋ
ـ
ﻠ
ـ
ﻰ ﺗ
ـ
ﺤ
ـ
ﻤ
ـ
ﻞ اﻟ
ـ
ﻘ
ـ
ﺪرة اﻟ
ـ
ﻜ
ـ
ﻬ
ـ
ﺮﺑ
ـ
ﺎﺋ
ـ
ﻴ
ـ
ﺔ اﻟ
ـ
ﻘ
ـ
ﺼ
ـ
ﻮى
اﻟ
ـ
ﻤ
ـ
ﻤ
ـ
ﺘ
ـ
ﺼ
ـ
ﺔ ﻣ
ـ
ﻦ ﻗ
ـ
ﺒ
ـ
ﻞ اﻟ
ـ
ﺠ
ـ
ﻬ
ـ
ﺎزوﻳ
ـ
ﻜ
ـ
ﻮن ﻣ
ـ
ﺸ
ـ
ﺎر ﻟ
ـ
ﻬ
ـ
ﺎ ﻓ
ـ
ﻲ ﻻ ﺋ
ـ
ﺤ
ـ
ﺔ اﻟ
ـ
ﺨ
ـ
ﺼ
ـ
ﺎﺋ
ـ
ﺺ اﻟ
ـ
ﻔ
ـ
ﻨ
ـ
ﻴ
ـ
ﺔ ﻟ
ـ
ﻠ
ـ
ﺠ
ـ
ﻬ
ـ
ﺎز
)اﻧﻈﺮﺻﻔﺤﺔ 91(.
ﻓﺮق ﺟﻬﺪ ﺷﺒﻜﺔ اﻟﻜﻬﺮﺑﺎء ﻳﺠﺐ أن ﺗﻜﻮن ﻓﻲ اﻟﻘﻴﻢ اﻟﺘﻲ ﺗﻜﻮن ﻣﻮﺟﻮدة واﻟﻤﺸﺎر ﻟﻬﺎ
ﻓﻲ ﻻ ﺋﺤﺔ اﻟﺨﺼﺎﺋﺺ اﻟﻔﻨﻴﺔ ﻟﻠﺠﻬﺎز)اﻧﻈﺮﺻﻔﺤﺔ 91(.
ﻣﻘﺒﺲ اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ )اﻷ ﻧﺜﻰ( ﻣﻼ ﺋﻢ ﻟﻘﺎﺑﺲ اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ )اﻟﺬآﺮ( اﻟﻤﺰود ﻣﻊ
اﻟﻐﺴﺎﻟﺔ ﻓﻲ ﺣﺎﻟﺔ ﻋﺪم ﺗﻮاﻓﻘﻬﻢ ﻗﻮﻣﻮا ﺑﻌﻤﻠﻴﺔ ﺗﻐﻴﻴﺮ اﺣﺪاهﻤﺎ.
ﺟ
ـ
ﻬ
ـ
ﺎزآ
ـ
ﻢ اﻟ
ـ
ﻜ
ـ
ﻬ
ـ
ﺮﺑ
ـ
ﺎﺋ
ـ
ﻲ ﻣ
ـ
ﺰود ﺑ
ـ
ﻘ
ـ
ﺎﺑ
ـ
ﺲ )اﻟ
ـ
ﺬآ
ـ
ﺮ( ﻣ
ـ
ﺼ
ـ
ﻬ
ـ
ﻮر وﻗ
ـ
ﺎدرﻋ
ـ
ﻠ
ـ
ﻰ ﺗ
ـ
ﺤ
ـ
ﻤ
ـ
ﻞ ﺗ
ـ
ﻴ
ـ
ﺎر آ
ـ
ﻬ
ـ
ﺮﺑ
ـ
ﺎﺋ
ـ
ﻲ
31 أﻣﺒﻴﺮ وﻳﻤﻜﻨﻜﻢ ادﺧﺎل هﺬا اﻟﻘﺎﺑﺲ ﺑﻤﻘﺒﺲ )اﻻ ﻧﺜﻰ( ﻳﺘﻮاﻓﻖ ﻣﻌﺔ ﻟﻼ ﺳﺘﺨﺪام اﻟﻤﺒﺎﺷﺮ،
اﻗﺮؤوا اﻟﺘﻌﻠﻴﻤﺎت اﻟﺘﺎﻟﻴﺔ ﻗﺒﻞ اﺳﺘﺨﺪام اﻟﺠﻬﺎز اﻟﻜﻬﺮﺑﺎﺋﻲ.
اﻧ
ـ
ﺘ
ـ
ﺒ
ـ
ﺎه: اﻟ
ـ
ﺠ
ـ
ﻬ
ـ
ﺎز اﻟ
ـ
ﻜ
ـ
ﻬ
ـ
ﺮﺑ
ـ
ﺎﺋ
ـ
ﻲ ﻳ
ـ
ﺠ
ـ
ﺐ أن ﻳ
ـ
ﻜ
ـ
ﻮن ﻣ
ـ
ﻮﺻ
ـ
ﻮل ﺑ
ـ
ﺨ
ـ
ﻂ أرض ﻓ
ـ
ﻌ
ـ
ﺎل، اﻟ
ـ
ﻌ
ـ
ﻤ
ـ
ﻠ
ـ
ﻴ
ـ
ﺎت
اﻟﻤﺸﺮوﺣﺔ أدﻧﺎه هﻲ ﺗﻌﻠﻴﻤﺎت ﻣﻮﺟﻪ اﻟﻰ ﻓﻨﻲ آﻬﺮﺑﺎﺋﻲ ﻣﺨﺘﺺ.
ﺗﻐﻴﻴﺮ اﻟﻤﻨﺼﻬﺮة )اﻟﻔﻴﻮز(
ﻋ
ـ
ﻨ
ـ
ﺪ ﺗ
ـ
ﻐ
ـ
ﻴ
ـ
ﻴ
ـ
ﺮ اﻟ
ـ
ﻤ
ـ
ﻨ
ـ
ﺼ
ـ
ﻬ
ـ
ﺮة )اﻟ
ـ
ﻔ
ـ
ﻴ
ـ
ﻮز( اﻟ
ـ
ﻤ
ـ
ﻌ
ـ
ﻄ
ـ
ﻮب، اﺳ
ـ
ﺘ
ـ
ﺨ
ـ
ﺪﻣ
ـ
ﻮا داﺋ
ـ
ﻤ
ـ
ﺎ ﻣ
ـ
ﻨ
ـ
ﺼ
ـ
ﻬ
ـ
ﺮة 31 اﻣ
ـ
ﺒ
ـ
ﻴ
ـ
ﺮ
ATSA ﺧﺎﺿﻌﺔ ﻟﻠﻤﻘﻴﺎس 2631 SB وأﻋﻴﺪوا ﻏﻄﺎء اﻟﻤﻨﺼﻬﺮة اﻟﻰ ﻣﻜﺎﻧﻪ اﻟﺬي
آ
ـ
ﺎن ﻓ
ـ
ﻴ
ـ
ﻪ، ﻓ
ـ
ﻲ ﺣ
ـ
ﺎﻟ
ـ
ﺔ ﻓ
ـ
ﻘ
ـ
ﺪان ه
ـ
ﺬا اﻟ
ـ
ﻐ
ـ
ﻄ
ـ
ﺎء ﻻ ﺗ
ـ
ﺴ
ـ
ﺘ
ـ
ﺨ
ـ
ﺪﻣ
ـ
ﻮا اﻟ
ـ
ﻘ
ـ
ﺎﺑ
ـ
ﺲ ﺣ
ـ
ﺘ
ـ
ﻰ اﻟ
ـ
ﺤ
ـ
ﺼ
ـ
ﻮل ﻋ
ـ
ﻠ
ـ
ﻰ
هﺬا اﻟﻐﻄﺎء وﺗﺮآﻴﺒﻪ ﻓﻲ ﻣﻜﺎﻧﻪ.
ﺗﻐﻴﻴﺮ ﻏﻄﺎء اﻟﻤﻨﺼﻬﺮات )اﻟﻔﻴﻮزات(:
اذا ﺗﻢ ﺗﻐﻴﻴﺮ ﻏﻄﺎء اﻟﻔﻴﻮزات ﺗﺎآﺪوا ﻣﻦ أن ﻟﻮﻧﻪ هﻮ اﻟﻠﻮن اﻟﺼﺤﻴﺢ واﻟﻤﺸﺎر ﻟﻪ
ﺑﻮاﺳﻄﺔ اﻟﺮﻗﻢ أو اﻟﻜﺘﺎﺑﺔ اﻟﻤﻠﻮﻧﺔ اﻟﻤﻮﺟﻮدة ﻋﻠﻰ ﻗﺎﻋﺪة اﻟﻘﺎﺑﺲ، ﻟﻘﻄﻊ اﻟﻐﻴﺎر، اﺳﺘﻌﻴﻨﻮا
ﻣﺒﺎﺷﺮة ﺑﻘﺴﻢ اﻟﺼﻴﺎﻧﺔ اﻟﻔﻨﻴﺔ اﻟﻘﺮﻳﺐ ﻋﻠﻴﻜﻢ.
ﻓﻚ اﻟﻘﺎﺑﺲ )اﻟﺬآﺮ(:
ﻓﻲ ﺣﺎﻟﺔ أن ﻳﻜﻮن اﻟﺠﻬﺎز ﻣﺰود ﺑﻘﺎﺑﺲ )اﻟﺬآﺮ( ﻻ ﻳﻤﻜﻦ ﻓﻜﻪ ﻷ ﻧﻪ ﻣﺼﻬﻮر وﺗﺮﻳﺪون
ﺗﻤﺮﻳﺮ ﺳﻠﻚ اﻟﺘﻐﺬﻳﺔ اﻟﻜﻬﺮﺑﺎﺋﻴﺔ ﻣﻦ ﺧﻼ ل ﺛﻘﻮب أو ﻓﺘﺤﺎت ﺻﻐﻴﺮة ﻻ ﻳﻤﺮ ﻣﻦ ﺧﻼ ﻟﻬﺎ
اﻟﻘﺎﺑﺲ ﻗﻮﻣﻮا ﺑﺘﻐﻴﻴﺮ اﻟﻘﺎﺑﺲ اﻟﻤﺼﻬﻮر ﺑﻘﺎﺑﺲ ﻳﻤﻜﻦ ﻓﻜﻪ وﺗﺮآﻴﺒﻪ وﻗﺎدر ﻋﻠﻰ ﺗﺤﻤﻞ
31 أﻣﺒﻴﺮ وﻳﺤﻤﻞ اﻟﺸﻌﺎر ISB.
أو
وﺻ
ـ
ﻞ ﺳ
ـ
ﻠ
ـ
ﻚ اﻟ
ـ
ﺘ
ـ
ﻐ
ـ
ﺬﻳ
ـ
ﺔ اﻟ
ـ
ﻜ
ـ
ﻬ
ـ
ﺮﺑ
ـ
ﺎﺋ
ـ
ﻴ
ـ
ﺔ ﺑ
ـ
ﻤ
ـ
ﻨ
ـ
ﺒ
ـ
ﻊ اﻟ
ـ
ﺘ
ـ
ﻴ
ـ
ﺎر اﻟ
ـ
ﻜ
ـ
ﻬ
ـ
ﺮﺑ
ـ
ﺎﺋ
ـ
ﻲ ﺑ
ـ
ﻮاﺳ
ـ
ﻄ
ـ
ﺔ ﻣ
ـ
ﻔ
ـ
ﺘ
ـ
ﺎح ﻗ
ـ
ﺎدر ﻋ
ـ
ﻠ
ـ
ﻰ
ﺗ
ـ
ﺤ
ـ
ﻤ
ـ
ﻞ 31 أﻣ
ـ
ﺒ
ـ
ﻴ
ـ
ﺮ )وﺧ
ـ
ﺎﺿ
ـ
ﻊ ﻟ
ـ
ﻠ
ـ
ﻤ
ـ
ﻘ
ـ
ﻴ
ـ
ﺎس 3375 SB ( ﻳ
ـ
ﻤ
ـ
ﻜ
ـ
ﻦ اﻟ
ـ
ﻮﺻ
ـ
ﻮل اﻟ
ـ
ﻴ
ـ
ﻪ ﺑ
ـ
ﺪون
ﺗﺤﺮﻳﻚ اﻟﺠﻬﺎز ﻣﻦ ﻣﻜﺎﻧﻪ.
ازاﻟﺔ اﻟﻘﺎﺑﺲ )اﻟﺬآﺮ(:
ﻗﺒﻞ رﻣﻲ اﻟﻘﺎﺑﺲ اﺟﻌﻠﻮة ﻏﻴﺮ ﻗﺎﺑﻞ ﻟﻼ ﺳﺘﻌﻤﺎل وذﻟﻚ ﺑﻜﺴﺮ رؤوﺳﻪ ﺑﺤﻴﺚ ﻻ ﻳﻤﻜﻦ
ادﺧﺎﻟﻪ داﺧﻞ ﺛﻘﻮب ﻣﻘﺒﺲ )اﻻ ﻧﺜﻰ( ﺑﺸﻜﻞ ﻋﻔﻮي.
ﺗﻌﻠﻴﻤﺎت ﻣﻦ أﺟﻞ ﺗﻮﺻﻴﻞ ﺳﻠﻚ اﻟﺘﻐﺬﻳﺔ اﻟﻜﻬﺮﺑﺎﺋﻴﺔ ﺑﻘﺎﺑﺲ )اﻟﺬآﺮ(:
ﻣﻬﻢ: أﻟﻮان اﻷ ﺳﻼ ك اﻟﺘﻐﺬﻳﻪ اﻟﻜﻬﺮﺑﺎﺋﻴﺔ ﺗﺸﻴﺮ اﻟﻰ اﻟﺘﺎﻟﻲ:
أﺻﻔﺮ/أﺧﻀﺮ ﺧﻂ أرض
ازرق ﻣﺤﺎﻳﺪ )ﻧﻴﻮﺗﺮل(
ﺑﻨﻲ ﺗﻐﺬﻳﺔ
وﻷ ن أﻟ
ـ
ﻮان ﺳ
ـ
ﻠ
ـ
ﻚ اﻟ
ـ
ﺘ
ـ
ﻐ
ـ
ﺬﻳ
ـ
ﺔ اﻟ
ـ
ﻜ
ـ
ﻬ
ـ
ﺮﺑ
ـ
ﺎﺋ
ـ
ﻴ
ـ
ﺔ ﻳ
ـ
ﻤ
ـ
ﻜ
ـ
ﻦ أن ﻻ ﻳ
ـ
ﻄ
ـ
ﺎﺑ
ـ
ﻘ
ـ
ﻮا اﻻ ﺷ
ـ
ﺎرات اﻟ
ـ
ﻤ
ـ
ﻠ
ـ
ﻮﻧ
ـ
ﺔ اﻟ
ـ
ﺘ
ـ
ﻲ
ﺗﻌﺮف ﻣﺮاﺑﻂ اﻟﻘﺎﺑﺲ، اﺗﺒﻌﻮا اﻟﺨﻄﻮات اﻟﺘﺎﻟﻴﺔ:
أوﺻﻠﻮا اﻟﺴﻠﻚ اﻷ ﺻﻔﺮ/اﻷ ﺧﻀﺮ ﺑﺎﻟﻤﺮﺑﻂ اﻟﻤﺸﺎر ﻟﻪ ﺑﺎﻟﺤﺮف E أو ﺑﺎﻟﺸﻌﺎر أو
اﻟﻠﻮن اﻷ ﺧﻀﺮ أو اﻷ ﺻﻔﺮ/اﻷ ﺧﻀﺮ
أوﺻﻠﻮا اﻟﺴﻠﻚ اﻟﺒﻨﻲ ﺑﺎﻟﻤﺮﺑﻂ اﻟﻤﺸﺎر ﻟﻪ ﺑﺎﻟﺤﺮف L أو ﺑﺎﻟﻠﻮن اﻷ ﺣﻤﺮ.
أوﺻﻠﻮا اﻟﺴﻠﻚ اﻷ زرق ﺑﺎﻟﻤﺮﺑﻂ اﻟﻤﺸﺎر ﻟﻪ ﺑﺎﻟﺤﺮف N أو ﺑﺎﻟﻠﻮن اﻷ ﺳﻮد.
اذا اﺳﺘﺨﺪﻣﺘﻢ ﻗﺎﺑﺲ )اﻟﺬآﺮ( 31 أﻣﺒﻴﺮ )3631 SB( رآﺒﻮا ﻣﻨﺼﻬﺮة )ﻓﻴﻮز( 31
أﻣﺒﻴﺮ ﻓﻲ اﻟﻤﻘﺒﺲ أو ﻓﻲ اﻟﻤﻬﺎي
ْ
أو ﻋﻠﻰ ﻟﻮﺣﺔ اﻟﺘﻮزﻳﻊ.
3
ﻓ
ـ
ﻲ ﺣ
ـ
ﺎﻟ
ـ
ﺔ اﻟ
ـ
ﺸ
ـ
ﻚ ﺑ
ـ
ﺎﻟ
ـ
ﺘ
ـ
ﻐ
ـ
ﺬﻳ
ـ
ﺔ اﻟ
ـ
ﻜ
ـ
ﻬ
ـ
ﺮﺑ
ـ
ﺎﺋ
ـ
ﻴ
ـ
ﺔ ﻟ
ـ
ﺠ
ـ
ﻬ
ـ
ﺎزآ
ـ
ﻢ اﺳ
ـ
ﺘ
ـ
ﺪﻋ
ـ
ﻮا ﻓ
ـ
ﻨ
ـ
ﻲ آ
ـ
ﻬ
ـ
ﺮﺑ
ـ
ﺎﺋ
ـ
ﻲ ﻣ
ـ
ﺨ
ـ
ﺘ
ـ
ﺺ ﻗ
ـ
ﺒ
ـ
ﻞ
وﺻﻞ اﻟﺠﻬﺎز ﺑﻤﻨﺒﻊ اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ.
وﺻﻞ ﻗﺎﺑﺲ )اﻟﺬآﺮ( ﺑﺪﻳﻞ:
أﻟﻮان اﻷ ﺳﻼ ك اﻟﺘﻐﺬﻳﻪ اﻟﻜﻬﺮﺑﺎﺋﻴﺔ ﺗﺸﻴﺮ اﻟﻰ اﻟﺘﺎﻟﻲ:
ازرق ﻣﺤﺎﻳﺪ )ﻧﻴﻮﺗﺮل( )N(
ﺑﻨﻲ ﺗﻐﺬﻳﺔ )L(
أﺻﻔﺮ/أﺧﻀﺮ ﺧﻂ أرض )E(
ازاﻟﺔ اﻟﺠﻬﺎز اﻟﻜﻬﺮﺑﺎﺋﻲ اﻟﺒﻴﺘﻲ:
ﻋﻨﺪ رﻣﻲ ﺟﻬﺎز آﻬﺮﺑﺎﺋﻲ ﺑﻴﺘﻲ، ﻳﺠﺐ ازاﻟﺔ ﻗﺎﺑﺲ اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ )اﻟﺬآﺮ( وذﻟﻚ
ﺑ
ـ
ﻘ
ـ
ﺺ ﺳ
ـ
ﻠ
ـ
ﻚ اﻟ
ـ
ﺘ
ـ
ﻐ
ـ
ﺬﻳ
ـ
ﺔ اﻟ
ـ
ﻜ
ـ
ﻬ
ـ
ﺮﺑ
ـ
ﺎﺋ
ـ
ﻴ
ـ
ﺔ ﺑ
ـ
ﺄﻗ
ـ
ﺮب ﻧ
ـ
ﻘ
ـ
ﻄ
ـ
ﺔ ﻣ
ـ
ﻤ
ـ
ﻜ
ـ
ﻨ
ـ
ﺔ ﻣ
ـ
ﻦ اﻟ
ـ
ﻘ
ـ
ﺎﺑ
ـ
ﺲ وﻗ
ـ
ﻮﻣ
ـ
ﻮا ﺑ
ـ
ﺘ
ـ
ﺤ
ـ
ﻄ
ـ
ﻴ
ـ
ﻢ
رؤوس اﻟﻘﺎﺑﺲ آﻤﺎ ذآﺮ ﺳﺎﺑﻘﺎ.
VERDE &
GIALLO
MARRONE
BLU
fusibile
13 ampere
SERRAFILO
CROSSBAR
ﻣ
ـ
ﻨ
ـ
ﺼ
ـ
ﻬ
ـ
ﺮة 31
أﻣﺒﻴﺮ
ﻣﺮﺑﻂ ﺳﻠﻚ
أﺧﻀﺮ
أﺻﻔﺮ
ﺑﻨﻲ
أزرق
!اﻟﻐﺴﺎﻟﺔ ﻻ ﺗﻮﺿﻊ ﻓﻲ اﻟﺨﺎرج ﺣﺘﻰ ﻟﻮ آﺎن اﻟﻤﻜﺎن ﻣﻐﻄﻰ وذﻟﻚ ﻷ ﻧﻪ ﻣﻦ اﻟﺨﻄﺮ ﺗﺮك
اﻟﺠﻬﺎز ﺗﺤﺖ ﻋﻮاﻣﻞ اﻟﻄﻘﺺ ﻣﺜﻞ اﻟﻤﻄﺮ ﺑﺮق رﻋﺪ اﻟﻰ اﺧﺮه.
! ﺑ
ـ
ﻌ
ـ
ﺪ اﻻ ﻧ
ـ
ﻬ
ـ
ﺎء ﻣ
ـ
ﻦ ﺗ
ـ
ﺮآ
ـ
ﻴ
ـ
ﺐ اﻟ
ـ
ﺠ
ـ
ﻬ
ـ
ﺎز ﻳ
ـ
ﺠ
ـ
ﺐ أن ﻳ
ـ
ﻜ
ـ
ﻮن ﻣ
ـ
ﻦ اﻟ
ـ
ﺴ
ـ
ﻬ
ـ
ﻞ اﻟ
ـ
ﻮﺻ
ـ
ﻮل اﻟ
ـ
ﻰ ﻣ
ـ
ﻘ
ـ
ﺒ
ـ
ﺲ
اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ )اﻷ ﻧﺜﻰ(.
! ﻻ ﺗﺴﺘﺨﺪﻣﻮا ﻣﻬﺎﻳﺌﺎت او ﻣﻘﺒﺲ ﻣﺘﻌﺪد اﻟﺜﻘﻮب أو اﺳﻼ ك ﺗﻄﻮﻳﻞ.
! ﺳﻠﻚ اﻟﺘﻐﺬﻳﺔ اﻟﻜﻬﺮﺑﺎﺋﻴﺔ ﻳﺠﺐ أن ﻻ ﻳﻜﻮن ﻣﻄﻮي أو ﻣﺤﺸﻮر ﺑﻴﻦ اﻷ ﺛﺎث.
!ﺳ
ـ
ﻠ
ـ
ﻚ اﻟ
ـ
ﺘ
ـ
ﻐ
ـ
ﺬﻳ
ـ
ﺔ اﻟ
ـ
ﻜ
ـ
ﻬ
ـ
ﺮﺑ
ـ
ﺎﺋ
ـ
ﻴ
ـ
ﺔ ﻳ
ـ
ﺠ
ـ
ﺐ أن ﻳ
ـ
ﺘ
ـ
ﻢ ﺗ
ـ
ﺒ
ـ
ﺪﻳ
ـ
ﻠ
ـ
ﻪ وﻗ
ـ
ﺖ اﻟ
ـ
ﺤ
ـ
ﺎﺟ
ـ
ﺔ ﻓ
ـ
ﻘ
ـ
ﻂ ﻣ
ـ
ﻦ ﻗ
ـ
ﺒ
ـ
ﻞ ﻓ
ـ
ﻨ
ـ
ﻲ ﻣ
ـ
ﺨ
ـ
ﺘ
ـ
ﺺ
وﻣﺆهﻞ ﻟﻠﻘﻴﺎم ﺑﻬﺬا.
اﻧﺘﺒﺎه: اﻟﺸﺮآﺔ اﻟﺼﺎﻧﻌﺔ ﺗﺴﻘﻂ ﻋﻦ ﻧﻔﺴﻬﺎ أي ﻣﺴﺆوﻟﻴﺔ ﻋﻦ أﺿﺮار ﻗﺪ ﺗﺤﺼﻞ ﻣﻦ
ﻋﺪم اﺗﺒﺎع واﺣﺘﺮام هﺬه ﻗﻮاﻋﺪ اﻷ ﻣﻦ.
81
AR
1
D
IWD 71251 S
61051
85
3
6
7
1
MPa1
MPa
52
10
1200
EC
2004/108/CE
(
119U
3
4
.
1061/2010
1015/2010ϭ
IWSC 61251
42
6
40
1200
2
3
,:&
:(((
34
AR
AR
35
3
1
.2
.3
.4
.5
.6
.7
.8
.9
ّ
ّ
ّ
AR
6022010/1061
1
60
4032010/1061
2
40
403 3
4044
l l 90 11200
3
1 2601200
ll
3-2 3401200
ll
4800
ll
3
---
l l 40 4 4800344
90 066 7l l 1200 40
20
170 - - - 7
l l
1200
20
120 - - - 7
l l 800 20
6
7
20 8
20800
ll
1
---20
30400
l
-
--- 9
10
40800
ll
---
11
40800
ll
---70
30600
ll
2--- 12
1330600
ll
2---60
1430600
ll
---60
-1200-
l
---36
-1200--
---
ﺔﻘﯿﻗد
1200--
---
ﺔﻘﯿﻗد
3
-
-
-
-
- -
-
37
AR
.
1
800
800
.
1
2
“ .)
،ﺎَﻀﻳأ ﻞﺑ .ﺔﻗﺎﻄﻟا كﻼﻬﺘﺳا ةرﻮﺗﺎﻔﻟ ءاﻮﺳ ﺔﺌﻴﺒﻠﻟ ءاﻮﺳ ةﺰﻴﻣ ﻲهو – ﺲﺑﻼﻤﻟا ﻞﺴﻐﻟ مﺪﺨﺘﺴﻤﻟا ءﺎﻤﻟا ﻦﻴﺨﺴﺗ مﺪﻌﺑ ﻚﻟذو ﺔﻗﺎﻄﻟا ﺮﻴﻓﻮﺗ ﻰﻠﻋ ﻞﻤﻌﺗ ﺔﻔﻴﻇو نإ
.ةدﺎﺘﻌﻤﻟا ﻞﻴﺴﻐﻟا ةرود ﻦﻣز ﻂﺳﻮﺘﻣ ﺲﻔﻧ ﻲﻓ ةزﺎﺘﻤﻣ ﻞﻴﺴﻏ ﺞﺋﺎﺘﻧ ﻦﻤﻀﻳ ﺎﻤﻣ ءﺎﻤﻟا ماﺪﺨﺘﺳا ﻦﻴﺴﺤﺗو ﻞﻴﺴﻐﻟا ةرود ﺔﻴﻟﺎﻌﻓ ﻢﻋد ﻰﻠﻋ ﻞﻤﻌﺗ
.ﺔﻠﺋﺎﺴﻟا ﺲﺑﻼﻤﻟا ﻒﻴﻈﻨﺗ تاﺮﻀﺤﺘﺴﻣ ماﺪﺨﺘﺳﺎﺑ ﻲﺻﻮﻧ ﻞﻀﻓأ ﺲﺑﻼﻣ ﻞﻴﺴﻏ ﺞﺋﺎﺘﻨﻟ
1200
ﺾﻣﻮﯿﺳ ،ﺔﺠﻣﺮﺒﻤﻟا ﻞﯿﺴﻐﻟا ةرود ﻊﻣ ﻖﻓاﻮﺘﺗ ةرﺎﺘﺨﻤﻟا ﺔﻔﯿﻇﻮﻟا ﻦﻜﺗ ﻢﻟ اذإ
.ﺔﻔﯿﻇﻮﻟا ﻞﯿﻐﺸﺗ ﻢﺘﯾ ﻦﻟو ﻢﺋﻼﻤﻟا ﺮﺷﺆﻤﻟا حﺎﺒﺼﻤﻟا
ﺾﻣﻮﯿﺳ ،ﺎﻘﺑﺎﺳ ﺎھرﺎﯿﺘﺧا ﻢﺗ ىﺮﺧأ ﺔﻔﯿﻇو ﻊﻣ ﺔﻘﻓاﻮﺘﻣ ةرﺎﺘﺨﻤﻟا ﺔﻔﯿﻇﻮﻟا ﻦﻜﺗ ﻢﻟ اذإ
؛ﻂﻘﻓ ﺔﯿﻧﺎﺜﻟا ﺔﻔﯿﻇﻮﻟا ﻂﯿﺸﻨﺗ ﻢﺘﯿﺳو ﻰﻟوﻻأ ﺔﻔﯿﻇﻮﻠﻟ ﻢﺋﻼﻤﻟا ﺮﺷﺆﻤﻟا حﺎﺒﺼﻤﻟا
.ﺖﺑﺎﺛ ﻞﻜﺸﺑ ﻂﺸﻨﻟا رﺎﯿﺨﻠﻟ ﻢﺋﻼﻤﻟا ﺮﺷﺆﻤﻟا حﺎﺒﺼﻤﻟا ءﻲﻀﯿﺳ
12
1400
1000
38
AR
!
12
3
1
1
1
2
3
.
2020
20
6
40
7
8 20
20
9
Gore-Tex
10
.11
12
13
14
.1
AR
39
!
2012/19/EU
AR
!
1
2
3
4
5
!
65
AR
AR
!
Mod
AR
AR
AR
195138388.02
06/2016
Üretici Firma:
Indesit Company Beyaz Eşya PAZARLAMA A.Ş.
Balmumcu Cad. Karahasan Sok.
No: 11, 34349– Balmumcu Beşiktaş – İstanbul
Tel: )0212( 355 53 00