iStorage diskAshur DT 2 User Manual
Displayed below is the user manual for diskAshur DT 2 by iStorage which is a product in the External Hard Drives category. This manual has pages.
Related Manuals
#1
www.istorage-uk.com
iStorage diskAshur DT2® Manual – v 1.8
Please make sure you remember your PIN (password), without it there
is no way to access the data on the drive.
If you are having difficulty using your diskAshur DT2 drive please contact our technical department
by email - support@istorage-uk.com or by phone on +44 (0) 20 8991 6260.
USER MANUAL
#2
iStorage diskAshur DT2® Manual – v 1.8
www.istorage-uk.com
Copyright © iStorage, Inc 2017. All rights reserved.
Windows is a registered trademark of Microsoft Corporation.
All other trademarks and copyrights referred to are the property of their respective owners.
Distribution of modified versions of this document is prohibited without the explicit permission of the copyright holder.
Distribution of the work or derivative work in any standard (paper) book form for commercial purposes is prohibited unless
prior permission is obtained from the copyright holder.
DOCUMENTATION IS PROVIDED AS IS AND ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND
WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE OR NON-INFRINGEMENT, ARE DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD
TO BE LEGALLY INVALID
All trademarks and brand names are the property of their respective owners
Trade Agreements Act (TAA) Compliant
#3
www.istorage-uk.com
iStorage diskAshur DT2® Manual – v 1.8
Table of Contents
Introduction ....................................................................................................................................4
Box Contents ..................................................................................................................................4
1. diskAshur DT2 Layout ..............................................................................................................5
2. Connecting your diskAshur DT2 ..............................................................................................6
3. diskAshur DT2 LED States .......................................................................................................7
4. How to use the diskAshur DT2 for the first time .......................................................................7
5. Unlocking the diskAshur DT2 .................................................................................................. 8
6. Locking the diskAshur DT2 ......................................................................................................8
7. Entering Admin Mode .............................................................................................................8
8. Changing the Admin PIN .........................................................................................................9
9. Adding a new User PIN in Admin Mode ..................................................................................10
10. Changing the User PIN in Admin Mode ..................................................................................10
11. Deleting the User PIN in Admin Mode ....................................................................................10
12. Set Read-Only in Admin Mode ................................................................................................ 11
13. Enable Read/Write in Admin Mode .........................................................................................11
14. How to create a Self-Destruct PIN ...........................................................................................11
15. How to delete the Self-Destruct PIN ........................................................................................12
16. How to Unlock with the Self-Destruct PIN ...............................................................................12
17. How to Create an Admin PIN after a Brute Force attack or Reset ............................................13
18. Setting the Unattended Auto-Lock Clock ................................................................................. 13
19. Turn off the Unattended Auto-Lock Clock ................................................................................ 14
20. How to Unlock diskAshur DT2 with User PIN ...........................................................................14
21. Changing the User PIN in User Mode .....................................................................................14
22. Set Read-Only in User Mode ................................................................................................... 15
23. Enable Read/Write in User Mode ............................................................................................15
24. Brute Force Protection .............................................................................................................16
25. How to perform a complete reset ............................................................................................ 16
26. Initialising and formatting the diskAshur DT2 .........................................................................17
27. diskAshur DT2 Setup for Mac OS ...........................................................................................19
28. diskAshur DT2 Setup for Linux (Ubuntu 14.04) ......................................................................21
29. Hibernating, Suspending or Logging off from the Operating System .....................................24
30. How to check Firmware in Admin Mode .................................................................................. 24
31. How to check Firmware in User Mode ..................................................................................... 25
32. Technical Support ...................................................................................................................26
33. Warranty and RMA information ...............................................................................................26
#4
iStorage diskAshur DT2® Manual – v 1.8
www.istorage-uk.com
Introduction
Box Contents
The diskAshur DT2 is an easy to use, ultra-secure, hardware encrypted desktop hard drive with capacities of up to 8TB.
Simply switch the power on and connect the USB 3.1 cable to any computer and enter a 7-15 digit PIN, if the correct PIN
is entered, all data stored on the drive will be decrypted and accessible. To lock the drive and encrypt all data, simply eject
the diskAshur DT2 from the host computer and the entire contents of the drive will be encrypted (full disk encryption) using
military grade AES 256-bit hardware encryption (XTS mode). If the drive is lost or stolen and an incorrect PIN is entered 15
consecutive times, the drive will reset, the encryption key will be deleted and all data previously stored on the drive will be
lost forever.
One of the unique and underlying security features of the GDPR compliant diskAshur DT2 is the dedicated hardware based
secure microprocessor (Common Criteria EAL4+ ready), which employs built-in physical protection mechanisms designed
to defend against external tamper, bypass attacks and fault injections. Unlike other solutions, the diskAshur DT2 reacts to an
automated attack by entering the deadlock frozen state, which renders all such attacks as useless. In plain and simple terms,
without the PIN there’s no way in!
1. diskAshur DT2 Drive
2. USB Cable
3. Universal Mains Adapter
4. Quick Start Guide
LED LIGHTS
LOCK
SHIFT
UNLOCK
USB 3.1 PORT Mains Power
ON/OFF SWITCHDESK LOCK SLOT AIR VENT
diskAshur DT2 rear view
- Standby State/Locked
- User Mode/Unlocked
- Admin Mode
Alphanumeric
Keypad
#5
www.istorage-uk.com
iStorage diskAshur DT2® Manual – v 1.8
1. diskAshur DT2 Layout
The “UNLOCK”button is used to access the diskAshur DT2 and it can also be used as an OK acknowledgement in the
following operations:
• Entering a PIN
• Confirming a new PIN
• Accessing various command settings
The “SHIFT” button can be used for additional combinations. SHIFT + 1 is a separate value than just 1.
To create a PIN using additional combinations, press and hold down the SHIFT button whilst entering your 7-15 digit PIN.
e.g. SHIFT + 26756498.
To lock diskAshur DT2 and return it to Standby State ( ) press the “Lock” button.
ABC DEF
GHI JKL MNO
PQRS TUV WXYZ
A
LED Indicator Lights
LOCK
SHIFT
UNLOCK
RED: Standby Mode
A
The indicator light displays the following colours to indicate the various modes of operation:
BLUE: Admin Mode
GREEN: User Mode
#6
iStorage diskAshur DT2® Manual – v 1.8
www.istorage-uk.com
2. Connecting your diskAshur DT2
Be sure to read the following information before you begin to use the diskAshur DT2.
Attention: Use only the cables provided with your diskAshur DT2.
You may damage the drive if you use a cable not included with the diskAshur DT2.
1. Ensure that the power switch on the back of the diskAshur DT2 is in the OFF position.
2. Connect the diskAshur DT2 to a power outlet using the included AC Adapter.
3. Attach the USB cable to the diskAshur DT2 drive and to an available USB port on your computer.
4. Turn the power switch on the back of the diskAshur DT2 to the ON position.
5. The LED indicator light should turn RED, indicating that the drive is now ready to use.
OFFON
USB 3.1 DC 12V
#7
www.istorage-uk.com
iStorage diskAshur DT2® Manual – v 1.8
3. diskAshur DT2 LED States
The diskAshur DT2 is shipped with a default Admin PIN of 11223344 and although it can be used straight out of the box with
the default Admin PIN, for security reasons we highly recommend a new Admin PIN be created immediately by
following the instructions under section 8 ‘Changing the Admin PIN’.
Please follow the 3 simple steps in the table below to unlock the diskAshur DT2 for the first time with the default Admin PIN.
4. How to use the diskAshur DT2 for the first time
Instructions - first time use LED LED State
1. Connect the diskAshur DT2 to a USB port RED LED will be solid awaiting PIN entry
2. Enter Admin PIN (default - 11223344) RED LED remains solid
3. Within 10 seconds press the “UNLOCK” button once
to unlock diskAshur DT2
GREEN and BLUE LEDs will alternately blink
several times and then to a solid BLUE LED
changing to a blinking GREEN and finally solid
GREEN LED
Note: Once the diskAshur DT2 has been successfully unlocked, the GREEN LED will remain on and in a
solid state. It can be locked down immediately by pressing the “LOCK” button once or by clicking the ‘Safely
Remove Hardware/Eject’ icon within your operating system. To ensure no data is corrupted, we recommend using
‘Safely Remove Hardware/Eject’.
When the diskAshur DT2 is plugged in, there are three possible behaviours for the LED indicators as shown in the table
below.
RED GREEN BLUE diskAshur DT2 State
Solid Off Off Factory Reset 1
Solid Solid Solid Brute Force 2
Solid Off Off Standby 3
1. In Factory Reset State, the drive is waiting for the operation to set up an Admin PIN.
2. In Brute Force state, the drive is waiting for an operation to get more PIN entry attempts.
3. In Standby state, the drive is waiting for an operation to unlock the drive, or enter Admin mode, or reset the drive.
#8
iStorage diskAshur DT2® Manual – v 1.8
www.istorage-uk.com
To lock the drive, press the “LOCK” button once or by clicking the ‘Safely Remove Hardware/Eject’ icon within your operating
system. If data is still being written to the drive, please wait until all data has been written to the drive before pressing the
‘LOCK’ button or safely ejecting from the Operating System. When the unattended Auto-Lock timeout is activated, the drive
will automatically lock after a predetermined amount of time.
6. Locking the diskAshur DT2
Note: The diskAshur DT2 cannot be recognized by the operating system in standby state.
5. Unlocking the diskAshur DT2
The diskAshur DT2 can be unlocked with either an Admin or User PIN whilst in standby state (solid RED LED).
1. To unlock as the Administrator, enter the Admin PIN and press the “UNLOCK” button.
2. To unlock as a User, first press the “UNLOCK” button (all LEDs, blink on and off) and then enter the User
PIN and press the “UNLOCK” button again.
3. If correct User PIN is entered, both GREEN and BLUE LEDs will blink alternately and then return to a solid GREEN LED.
4. If correct Admin PIN is entered, both GREEN and BLUE LEDs will blink alternately, then to a solid BLUE for 1 second and
then to the unlocked state, a solid GREEN LED.
5. If correct PIN is entered, the drive displays as “iStorage diskAshur DT2 USB Device” under “Computer Management/De-
vice Manager”.
In an unlocked state (GREEN LED), there are two possible behaviours for the LED indicators, shown in the table below.
RED GREEN BLUE diskAshur DT2
Off Solid Off No data transfer
Off Blink Off Data transfer in progress
To enter the Admin Mode, do the following:
7. Entering Admin Mode
1. In standby state (solid RED LED), press and hold
down “UNLOCK + 1” buttons
Solid RED LED will change to blinking GREEN
and BLUE LEDs
2. Enter the Admin PIN (default - 11223344) and press
“UNLOCK” button
GREEN and BLUE LEDs blink rapidly together
for a few seconds then to a solid GREEN and
finally a solid BLUE LED indicating the
diskAshur DT2 is in “Admin Mode”
To exist Admin mode, press the “LOCK” button.
#9
www.istorage-uk.com
iStorage diskAshur DT2® Manual – v 1.8
8. Changing the Admin PIN
1. In Admin mode, press and hold down
“UNLOCK + 2” buttons
Solid BLUE LED will change to blinking GREEN
and solid BLUE LEDs
2. Enter NEW Admin PIN and press “UNLOCK” button
Blinking GREEN and solid BLUE LEDs will
switch to a single GREEN LED blink and then
back to blinking GREEN and solid BLUE LEDs
3. Re-enter the NEW Admin PIN and press “UNLOCK”
button
Blinking GREEN and solid BLUE LEDs change
to a rapidly blinking BLUE LED and finally to a
solid BLUE LED indicating the Admin PIN has
been successfully changed
To change the Admin PIN, first enter the “Admin Mode” as described in section 7. Once the drive is in Admin Mode
(solid BLUE LED) proceed with the following steps.
PIN requirements:
• Must be between 7-15 digits in length
• Must not contain only repetitive numbers, e.g. (3-3-3-3-3-3-3)
• Must not contain only consecutive numbers, e.g. (1-2-3-4-5-6-7), (7-8-9-0-1-2-3-4), (7-6-5-4-3-2-1)
Examples of these types of Alphanumerical PINs are:
• For “password” you would press the following keys:
7 (pqrs) 2 (abc) 7 (pqrs) 7 (pqrs) 9 (wxyz) 6 (mno) 7 (pqrs) 3 (def)
• For “istorage” you would press:
4 (ghi) 7 (pqrs) 8 (tuv) 6 (mno) 7 (pqrs) 2 (abc) 4 (ghi) 3 (def)
Using this method, long and easy to remember PINs can be created.
Password Tip: You can create a memorable word, name, phrase or any other Alphanumerical PIN combination
by simply pressing the key with the corresponding letters on it.
Note: The SHIFT key can be used for additional combinations. SHIFT + 1 is a separate value than just 1.
To create a PIN using additional combinations, press and hold down the SHIFT button whilst entering
your 7-15 digit PIN. e.g. SHIFT + 26756498.
#10
iStorage diskAshur DT2® Manual – v 1.8
www.istorage-uk.com
9. Adding a new User PIN in Admin Mode
11. Deleting the User PIN in Admin Mode
To add a New User, first enter the “Admin Mode” as described in section 7. Once the drive is in Admin Mode
(solid BLUE LED) proceed with the following steps.
1. In Admin mode, press and hold down
“UNLOCK + 3” buttons
Solid BLUE LED will change to blinking GREEN
and solid BLUE LEDs
2. Enter New User PIN and press “UNLOCK” button
Blinking GREEN and solid BLUE LEDs will
switch to a single GREEN LED blink and then
back to blinking GREEN and solid BLUE LEDs
3. Re-enter the New User PIN and press “UNLOCK”
button
GREEN LED rapidly blinks for a few seconds
then changes to a solid BLUE LED indicating the
User PIN has been successfully created
To delete a User PIN, first enter the “Admin Mode” as described in section 7. Once the drive is in Admin Mode
(solid BLUE LED) proceed with the following steps.
1. In Admin mode, press and hold down “SHIFT + 3”
buttons and release
Solid BLUE LED will change to blinking RED
LED
2. Press and hold down “SHIFT + 3” buttons again.
Blinking RED LED will change to solid RED
LED and then to a solid BLUE LED indicating
the User PIN was successfully deleted
10. Changing the User PIN in Admin Mode
To change an existing User PIN, first enter the “Admin Mode” as described in section 7. Once the drive is in Admin
Mode (solid BLUE LED) proceed with the following steps.
1. In Admin mode, press and hold down
“UNLOCK + 3” buttons
Solid BLUE LED will change to blinking GREEN
and solid BLUE LEDs
2. Enter New User PIN and press “UNLOCK” button
Blinking GREEN and solid BLUE LEDs will
switch to a single GREEN LED blink and then
back to blinking GREEN and solid BLUE LEDs
3. Re-enter the New User PIN and press “UNLOCK”
button
GREEN LED rapidly blinks for a few seconds
then changes to a solid BLUE LED indicating the
User PIN has been successfully changed
#11
www.istorage-uk.com
iStorage diskAshur DT2® Manual – v 1.8
12. Set Read-Only in Admin Mode
When Admin writes content to the diskAshur DT2 and restricts access to read-only, the User cannot change this setting in
User mode. To set the diskAshur DT2 to Read-Only, first enter the “Admin Mode” as described in section 7. Once the drive
is in Admin Mode (solid BLUE LED) proceed with the following steps.
1. In Admin mode, press and hold down “7 + 6”
buttons. (7=Read + 6=Only) Solid BLUE LED will change to blinking GREEN
and BLUE LEDs
2. Release 7+6 buttons and press “UNLOCK”GREEN and BLUE LEDs will change to a solid
GREEN LED and then to a solid BLUE LED
indicating the drive is configured as Read-Only
13. Enable Read/Write in Admin Mode
To set the diskAshur DT2 to Read/Write, first enter the “Admin Mode” as described in section 7. Once the drive is in
Admin Mode (solid BLUE LED) proceed with the following steps.
1. In Admin mode, press and hold down “7 + 9”
buttons. (7=Read + 9=Write)
Solid BLUE LED will change to blinking GREEN
and BLUE LEDs
2. Release 7+9 buttons and press “UNLOCK”GREEN and BLUE LEDs change to a solid
GREEN LED then to a solid BLUE LED
indicating the drive is configured as Read/Write
14. How to create a Self-Destruct PIN
The self-destruct feature allows you to set a PIN which can be used to perform a crypto-erase on the entire drive.
When used, the self-destruct PIN will delete ALL data, Admin/User PINs and then unlock the drive. Activating this
feature will cause the Self-Destruct PIN to become the new User PIN and the diskAshur DT2 will need to be partitioned
and formatted before any new data can be added to the drive.
To set the Self-Destruct PIN, first enter the “Admin Mode” as described in section 7. Once the drive is in Admin Mode
(solid BLUE LED) proceed with the following steps.
1. In Admin mode, press and hold down
“UNLOCK + 6” buttons Solid BLUE LED will change to blinking GREEN
and solid BLUE LEDs
2. Create a 7-15 digit Self-Destruct PIN and press the
“UNLOCK” button
Blinking GREEN and solid BLUE LEDs will
switch to a single GREEN LED blink and then
back to blinking GREEN and solid BLUE LEDs
3. Re-enter the PIN and press the “UNLOCK” button
GREEN LED will rapidly blink for several
seconds and then changes to a solid BLUE LED
to indicate the Self-Destruct PIN has been
successfully configured
Important: If data has just been copied to the diskAshur DT2, make sure to properly disconnect the drive
first by clicking ‘Safely Remove Hardware/Eject’ the diskAshur DT2 from the Operating System before
reconnecting and setting the diskAshur DT2 as ‘Read-Only/Write-Protect’.
#12
iStorage diskAshur DT2® Manual – v 1.8
www.istorage-uk.com
1. In standby state, press the “UNLOCK” button RED LED switches to all LEDs, RED, GREEN &
BLUE blinking on and off
2. Enter your Self-Destruct PIN and press the
“UNLOCK” button
RED, GREEN and BLUE blinking LEDs will
change to GREEN and BLUE LEDs alternating
on and off for approximately 15 seconds and
finally shifts to a solid GREEN LED
16. How to Unlock with the Self-Destruct PIN
When used, the self-destruct PIN will delete the encryption key, ALL data, Admin/User PINs and then unlock the
drive. Activating this feature will cause the Self-Destruct PIN to become the new USER PIN and the diskAshur DT2 will
need to be partitioned and formatted before any new data can be added to the drive.
To activate the Self-Destruct mechanism, the drive needs to be in the standby state (solid RED LED) and then proceed with the
following steps.
15. How to Delete the Self-Destruct PIN
1. In Admin mode, press and hold down
“SHIFT + 6” buttons Solid BLUE LED will change to a blinking RED
LED
2. Press and hold down “SHIFT + 6” buttons again
Blinking RED LED will become solid and then
change to a solid BLUE LED indicating the
Self-Destruct PIN was successfully deleted
To delete the Self-Destruct PIN, first enter the “Admin Mode” as described in section 7. Once the drive is in Admin Mode
(solid BLUE LED) proceed with the following steps.
Important: When the Self-Destruct mechanism is activated, all data, the encryption key and the Admin/User
PINs are deleted. The Self-Destruct PIN becomes the User PIN. No Admin PIN exists after
the Self-Destruct mechanism is activated. The diskAshur DT2 will need to be reset (see ‘How to
perform a complete reset’ Section 25, on page 16) first in order to create an Admin PIN with full
Admin privileges including the ability to create a User PIN.
#13
www.istorage-uk.com
iStorage diskAshur DT2® Manual – v 1.8
17. How to Create an Admin PIN after a Brute Force attack or Reset
It will be necessary after a Brute Force attack or when the diskAshur DT2 has been reset to create an Admin PIN before the
drive can be used. If the drive has been brute forced or reset, the drive will be in a standby state (solid RED LED). to create an
Admin PIN proceed with the following steps.
PIN requirements:
• Must be between 7-15 digits in length
• Must not contain only repetitive numbers, e.g. (3-3-3-3-3-3-3)
• Must not contain only consecutive numbers, e.g. (1-2-3-4-5-6-7), (7-8-9-0-1-2-3-4), (7-6-5-4-3-2-1)
18. Setting the Unattended Auto-Lock Clock
To protect against unauthorised access if the drive is unlocked and unattended, diskAshur DT2 can be set to
automatically lock after a pre-set amount of time. In its default state, the diskAshur DT2 Unattended Auto Lock feature is
turned off. The Unattended Auto Lock can be set to activate between 5 - 99 minutes.
To set the Unattended Auto Lock, first enter the “Admin Mode” as described in section 7. Once the drive is in Admin
Mode (solid BLUE LED) proceed with the following steps.
1. In Admin mode, press and hold down
“UNLOCK + 5” buttons
Solid BLUE LED will change to blinking GREEN
and BLUE LEDs
2. Enter the amount of time that you would like to set the Auto-Lock timeout feature for, the minimum time that can be set is
5 minutes and the maximum being 99 minutes (5-99 minutes). For example enter:
05 for 5 minutes
20 for 20 minutes
99 for 99 minutes
3. Press the “SHIFT” button
Blinking GREEN and BLUE LEDs will change to
a solid GREEN for a second and then finally to a
solid BLUE LED indicating the Auto-Lock time
out is successfully configured
1. In Standby state, press and hold down
“SHIFT + 1” buttons
Solid RED LED will change to blinking GREEN
and solid BLUE LEDs
2. Enter NEW Admin PIN and press “UNLOCK” button
Blinking GREEN and solid BLUE LEDs will
switch to a single GREEN LED blink and then
back to blinking GREEN and solid BLUE LEDs
3. Re-enter the NEW Admin PIN and press “UNLOCK”
button
Blinking GREEN LED and solid BLUE LED
change to BLUE LED rapidly blinking for a few
seconds and then to a solid BLUE LED indicat-
ing the Admin PIN was successfully configured.
Note: The SHIFT key can be used for additional combinations. SHIFT + 1 is a separate value than just 1.
To create a PIN using additional combinations, press and hold down the SHIFT button whilst entering
your 7-15 digit PIN. e.g. SHIFT + 26756498.
#14
iStorage diskAshur DT2® Manual – v 1.8
www.istorage-uk.com
21. Changing the User PIN in User Mode
1. In User mode press and hold down “UNLOCK + 4”Solid GREEN LED will change to a blinking
GREEN LED and a solid BLUE LED
2. Enter New User PIN and press the “UNLOCK” button
Blinking GREEN and solid BLUE LEDs will
switch to a single GREEN LED blink and then
back to blinking GREEN and solid BLUE LEDs
3. Re-enter New User PIN and press the “UNLOCK”
button
Blinking GREEN and solid BLUE LEDs will
switch to a rapidly blinking GREEN LED and
then to a solid GREEN LED indicating
successful User PIN change
20. How to Unlock diskAshur DT2 with User PIN
1. In the standby state (solid RED LED) Press the
“UNLOCK” button
RED LED switches to all LEDs, RED, GREEN &
BLUE blinking on and off
2. Enter User PIN and press the “UNLOCK” button
RED, GREEN and BLUE blinking LEDs will
change to alternating GREEN and BLUE LEDs
then to a rapidly blinking GREEN LED and
finally shifts to a solid GREEN LED indicating
drive successfully unlocked in User mode
To change the User PIN, first unlock the diskAshur DT2 with a User PIN as described above in section 20. Once the drive is
in User Mode (solid GREEN LED) proceed with the following steps.
19. Turn off the Unattended Auto-Lock Clock
1. In Admin mode, press and hold down
“UNLOCK + 5” buttons
Solid BLUE LED will change to blinking GREEN
and BLUE LEDs
2. Enter “00” and press the “SHIFT” button
Blinking GREEN and BLUE LEDs will change to
a solid GREEN for a second and then finally to a
solid BLUE LED indicating the Auto-Lock time
out has been successfully switched off
To turn off the Unattended Auto Lock, first enter the “Admin Mode” as described in section 7. Once the drive is in Admin
Mode (solid BLUE LED) proceed with the following steps.
#15
www.istorage-uk.com
iStorage diskAshur DT2® Manual – v 1.8
22. Set Read-Only in User Mode
To set the diskAshur DT2 to Read-Only, first enter the “User Mode” as described in section 20. Once the drive is in User
Mode (solid GREEN LED) proceed with the following steps.
1. In User mode, press and hold down “7 + 6”
buttons. (7=Read + 6=Only) Solid GREEN LED will change to blinking
GREEN and BLUE LEDs
2. Release 7+6 buttons and press “UNLOCK”
GREEN and BLUE LEDs will change to a solid
GREEN LED indicating the drive is configured
as Read-Only
Note: 1. This setting is activated the next time the drive is unlocked.
2. If a User set the drive as Read-Only, Admin can override it by setting the drive as Read/Write in
Admin mode.
3. If Admin set the drive as Read-Only, the User cannot set the drive as Read/Write
23. Enable Read/Write in User Mode
To set the diskAshur DT2 to Read/Write, first enter the “User Mode” as described in section 20. Once the drive is in User
Mode (solid GREEN LED) proceed with the following steps.
1. In User mode, press and hold down “7 + 9”
buttons. (7=Read + 9=Write) Solid GREEN LED will change to blinking
GREEN and BLUE LEDs
2. Release 7+9 buttons and press “UNLOCK”
GREEN and BLUE LEDs will change to a solid
GREEN LED indicating the drive is configured
as Read/Write
Note: 1. This setting is activated the next time the drive is unlocked.
2. If a User set the drive as Read-Only, Admin can override it by setting the drive as Read/Write in
Admin mode.
3. If Admin set the drive as Read-Only, the User cannot set the drive as Read/Write
Important: If data has just been copied to the diskAshur DT2, make sure to properly disconnect the drive
first by clicking ‘Safely Remove Hardware/Eject’ the diskAshur DT2 from the Operating System before
reconnecting and setting the diskAshur DT2 as ‘Read-Only/Write-Protect’.
#16
iStorage diskAshur DT2® Manual – v 1.8
www.istorage-uk.com
To perform a complete reset, the diskAshur DT2 must be in a standby state (solid RED LED). Once the drive is reset then all
Admin/User PINs, the encryption key and all data will be deleted and lost forever and the drive will need to be formatted and
partitioned before it can be reused.
To reset the diskAshur DT2 proceed with the following steps.
25. How to perform a complete reset
1. In standby state, press and hold down “0” button
until all LEDs blink alternately on and off
Solid RED LED will change to all LEDs, RED,
GREEN and BLUE blinking alternately on and
off
2. Press and hold down “2 + 7” buttons until all LEDs
become solid for a second and then to a solid RED LED
RED, GREEN and BLUE alternating LEDs will
change to all solid for a second and then to a
solid RED LED indicating the drive has been
reset
If an incorrect PIN is entered 15 (3 x 5 PIN clusters) consecutive times, then all Admin/User PINs, the encryption key and all
data will be deleted and lost forever. The diskAshur DT2 will then need to be formatted and partitioned before it can be
reused.
1. If a PIN is entered incorrectly 5 (five) consecutive times, all LEDs - RED, GREEN, BLUE will light up and become solid.
2. Switch the ON/OFF power button OFF and then back ON again to get five more PIN attempts. If PIN is incorrectly
entered 5 more times, (10 in total - 5 from step 1 and 5 from step 2) all LEDs - RED, GREEN, BLUE will light up and become
solid again.
3. Switch the ON/OFF power button OFF, then hold down the “SHIFT” button while switching the power back ON again,
all LEDs - RED, GREEN, BLUE will light up and blink together.
4. With all LEDs blinking, enter “47867243” and press the “UNLOCK” button to get 5 final attempts.
24. Brute Force Protection
Important: After a complete reset a new Admin PIN must be created, refer to Section 17 on page 13 on ‘How to
Create an Admin PIN after a Brute Force attack or Reset’, the diskAshur DT2 will also need to be
partitioned and formatted before any new data can be added to the drive.
Caution: After 15 consecutive incorrect PIN entries the Brute Force Defence Mechanism activates and deletes
all Admin/User PINs, the encryption key and data. A new Admin PIN must be created, refer to Section
17 on page 13 on ‘How to Create an Admin PIN after a Brute Force attack or Reset’, the diskAshur DT2
will also need to be partitioned and formatted before any new data can be added to the drive.
#17
www.istorage-uk.com
iStorage diskAshur DT2® Manual – v 1.8
5. In the Computer Manage window, click Disk Management. In the Disk Management window, the diskAshur DT2 is
recognised as an unknown device that is uninitialised and unallocated.
6. Right-click Unknown Disk, and then select Initialise Disk.
Note: If the Initialise Disk Wizard window opens, click Cancel.
After a ‘Brute Force Attack’ or a complete reset of the diskAshur DT2 will delete all data, encryption key and partition settings.
You will need to initialise and format the diskAshur DT2 before it can be used.
To initialise your diskAshur DT2, do the following:
1. Attach the diskAshur DT2 to the computer.
2. Create a new Admin PIN - see page 13, section 17, ‘How to create an Admin PIN after a Brute Force attack or reset’.
3. With the diskAshur DT2 in standby state (RED LED) enter New Admin PIN to unlock (GREEN LED).
4. Windows 7: Right click Computer and then click Manage and then select Disk Management
Windows 8: Right-click left corner of desktop and select Disk Management
Windows 10: Right click on the start button and select Disk Management
26. Initialising and formatting the diskAshur DT2
#18
iStorage diskAshur DT2® Manual – v 1.8
www.istorage-uk.com
9. Click Next.
10. If you need only one partition, accept the default partition size and click Next.
11. Assign a drive letter or path and click Next.
12. Create a volume label, select Perform a quick format, and then click Next.
13. Click Finish.
14. Wait until the format process is complete. The diskAshur DT2 will be recognised and it is available for use.
7. In the Initialise Disk window, click OK.
8. Right-click in the blank area under the Unallocated section, and then select New Simple Volume. The Welcome to
the New Simple Volume Wizard window opens.
#19
www.istorage-uk.com
iStorage diskAshur DT2® Manual – v 1.8
Your diskAshur DT2 is preformatted in NTFS for Windows. To reformat the drive to a Mac compatible format please read
below.
Once the drive is unlocked, open Disk Utility from Applications/Utilities/Disk Utilities.
To format the diskAshur DT2:
1. Select diskAshur DT2 from the list of drives and volumes. Each drive in the list will display its capacity, manufacturer, and
product name, such as ‘iStorage diskAshur DT2 Media’ or 232.9 diskAshur DT2.
27. diskAshur DT2 Setup for Mac OS
2. Click the ‘Erase’ button (figure 1).
3. Enter a name for the drive (figure 2). The default name is Untitled. The name of the drive will eventually appear on the
desktop.
figure 2
figure 1
#20
iStorage diskAshur DT2® Manual – v 1.8
www.istorage-uk.com
4. Select a scheme and volume format to use. The Volume Format dropdown menu (figure 3) lists the available drive formats
that the Mac supports. The recommended format type is ‘Mac OS Extended (Journaled).’ The scheme format dropdown menu
lists the available schemes to use (figure 4). We recommend using ‘GUID Partition Map’ on drives larger than 2TB.
5. Click the ‘Erase’ button. Disk Utility will unmount the volume from the desktop, erase it, and then remount it on the
desktop.
figure 3
figure 4
#21
www.istorage-uk.com
iStorage diskAshur DT2® Manual – v 1.8
28. diskAshur DT2 Setup for Linux (Ubuntu 14.04)
If your diskAshur DT2 has been initialised and formatted in NTFS for Windows, you can directly use the drive on Ubuntu.
If not, please read below.
To format the diskAshur DT2 as FAT filesystem:
1. Open ‘Unity Dash’ and type ‘Disks’ in the search box. Click on the ‘Disks’ utility when displayed.
2. Click to select the drive (6.0 TB Hard Disk) under ‘Devices’. Next click on the gears icon under ‘Volumes’ and then click
on ‘Format’.
3. Select ‘Compatible with all systems and devices(FAT)’ for the ‘Type’ option. And enter a name for the drive,
e.g: diskAshur DT2. Then, click the ‘Format’ button.
#22
iStorage diskAshur DT2® Manual – v 1.8
www.istorage-uk.com
4. Click ‘Format’ again.
5. The drive will start to be formatted.
6. After the format process is finished, click to mount the drive to Ubuntu.
#23
www.istorage-uk.com
iStorage diskAshur DT2® Manual – v 1.8
7. Now the drive should be mounted to Ubuntu and ready to use.
8. A disk icon will be shown as seen in the image below. You can click the disk icon to open your drive.
Lock diskAshur DT2 for Linux (Ubuntu 14.04)
It is strongly recommended to right click your drive icon and then click ‘Safely remove’ in the OS to eject (lock) your
diskAshur DT2, especially after data has been copied or deleted from the drive.
#24
iStorage diskAshur DT2® Manual – v 1.8
www.istorage-uk.com
30. How to check Firmware in Admin mode
1. In Admin mode press and hold down “3 + 8” until
GREEN and BLUE LEDs blink together
Solid BLUE LED will change to blinking GREEN
and BLUE LEDs
2. Press the “UNLOCK” button and the following happens;
a. All LED’s (RED, GREEN & BLUE) become solid for 1 second.
b. RED LED blinks indicating the integral part of the firmware revision number.
c. GREEN LED blinks indicating the fractional part.
d. All LED’s (RED, GREEN & BLUE) become solid for 1 second.
e. LEDs return to solid BLUE
To check the firmware revision number, first enter the “Admin Mode” as described in section 7. Once the drive is in Admin
Mode (solid BLUE LED) proceed with the following steps.
For example, if the firmware revision number is ‘1.2’, the RED LED will blink once (1) and the GREEN LED will blink two (2)
times. Once the sequence has ended the RED, GREEN & BLUE LED’s will blink together once and then return to a solid BLUE
LED.
29. Hibernating, Suspending, or Logging off from the Operating System
Be sure to save and close all the files on your diskAshur DT2 before hibernating, suspending, or logging off from the
operating system.
It is recommended that you lock the diskAshur DT2 manually before hibernating, suspending, or logging off from your
system.
To lock, simply press the ‘LOCK’ button on the diskAshur DT2 or by clicking the ‘Safely Remove Hardware/Eject’ icon within
your operating system.
Attention: To ensure your data is secure, be sure to lock your diskAshur DT2 if you are away from your
computer.
#25
www.istorage-uk.com
iStorage diskAshur DT2® Manual – v 1.8
31. How to check Firmware in User Mode
1. In User mode press and hold down “3 + 8” until
GREEN and BLUE LEDs blink together
Solid GREEN LED will change to blinking
GREEN and BLUE LEDs
2. Press the “UNLOCK” button and the following happens;
a. All LED’s (RED, GREEN & BLUE) become solid for 1 second.
b. RED LED blinks indicating the integral part of the firmware revision number.
c. GREEN LED blinks indicating the fractional part.
d. All LED’s (RED, GREEN & BLUE) become solid for 1 second.
e. LEDs return to solid GREEN
To check the firmware revision number, first enter the “User Mode” as described in section 20. Once the drive is in User
Mode (solid GREEN LED) proceed with the following steps.
For example, if the firmware revision number is ‘1.2’, the RED LED will blink once (1) and the GREEN LED will blink two (2)
times. Once the sequence has ended the RED, GREEN & BLUE LED’s will blink together once and then return to a solid BLUE
LED.
#26
iStorage diskAshur DT2® Manual – v 1.8
www.istorage-uk.com
iStorage provides the following helpful resources for you:
iStorage’s Website
https://www.istorage-uk.com
E-mail correspondence
support@istorage-uk.com
Telephone support with our Technical Support Department on +44 (0) 20 8991-6260.
iStorage’s Technical Support Specialists are available from 9:00 a.m. to 5:30 p.m. GMT - Monday through Friday.
32. Technical Support
Two Year Warranty:
iStorage offers a 2-year warranty on the iStorage diskAshur DT2 against defects in materials and workmanship under
normal use. The warranty period is effective from the date of purchase either directly from iStorage or an authorised reseller.
Disclaimer and terms of warranty:
THE WARRANTY BECOMES EFFECTIVE ON THE DATE OF PURCHASE AND MUST BE VERIFIED WITH YOUR SALES RECEIPT OR INVOICE DISPLAYING THE DATE OF PRODUCT
PURCHASE.
ISTORAGE WILL, AT NO ADDITIONAL CHARGE, REPAIR OR REPLACE DEFECTIVE PARTS WITH NEW PARTS OR SERVICEABLE USED PARTS THAT ARE EQUIVALENT TO NEW IN
PERFORMANCE. ALL EXCHANGED PARTS AND PRODUCTS REPLACED UNDER THIS WARRANTY WILL BECOME THE PROPERTY OF ISTORAGE.
THIS WARRANTY DOES NOT EXTEND TO ANY PRODUCT NOT PURCHASED DIRECTLY FROM ISTORAGE OR AN AUTHORIzED RESELLER OR TO ANY PRODUCT THAT HAS BEEN
DAMAGED OR RENDERED DEFECTIVE: 1. AS A RESULT OF ACCIDENT, MISUSE, NEGLECT, ABUSE OR FAILURE AND/OR INABILITY TO FOLLOW THE WRITTEN INSTRUCTIONS
PROVIDED IN THIS INSTRUCTION GUIDE: 2. BY THE USE OF PARTS NOT MANUFACTURED OR SOLD BY ISTORAGE; 3. BY MODIFICATION OF THE PRODUCT; OR 4. AS A RESULT
OF SERVICE, ALTERNATION OR REPAIR BY ANYONE OTHER THAN ISTORAGE AND SHALL BE VOID. THIS WARRANTY DOES NOT COVER NORMAL WEAR AND TEAR.
NO OTHER WARRANTY, EITHER EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, HAS BEEN OR WILL BE
MADE BY OR ON BEHALF OF ISTORAGE OR BY OPERATION OF LAW WITH RESPECT TO THE PRODUCT OR ITS INSTALLATION, USE, OPERATION, REPLACEMENT OR REPAIR.
ISTORAGE SHALL NOT BE LIABLE BY VIRTUE OF THIS WARRANTY, OR OTHERWISE, FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGE INCLUDING ANY LOSS OF
DATA RESULTING FROM THE USE OR OPERATION OF THE PRODUCT, WHETHER OR NOT ISTORAGE WAS APPRISED OF THE POSSIBILITY OF SUCH DAMAGES.
33. Warranty and RMA information
#27
www.istorage-uk.com
iStorage diskAshur DT2® Manual – v 1.8
© iStorage, 2017. All rights reserved.
iStorage Limited, iStorage House, 13 Alperton Lane
Perivale, Middlesex. UB6 8DH, England
Tel: +44 (0) 20 8991 6260 | Fax: +44 (0) 20 8991 6277
e-mail: info@istorage-uk.com | web: www.istorage-uk.com