KitchenAid KCBDR 18600 User Manual
Displayed below is the user manual for KCBDR 18600 by KitchenAid which is a product in the Fridge-Freezers category. This manual has pages.
Related Manuals
Instructions for use
Important safety instructions 4
Safeguarding the environment 6
Before using the appliance 6
Precautions and general recommendations 7
Energy-saving tips 7
Electrical connection for Great Britain and Ireland only 8
Using for the first time 8
Maintenance and cleaning of the applicance 8
Replacing the light bulb or LED (depending on the model) 9
In the event of non-use of the applicance 9
In the event of an interruption to the power supply 9
Refrigerator compartment 9
Freezer compartment 10
How to defrost the freezer compartment (depending on the model) 11
STOP FROST SYSTEM (depending on the model) 11
Procedure to clean the STOP FROST accessory 11
“Zero Degrees” compartment (depending on the model) 12
Use of wooden accessories (if present) 14
Technical Assistance Service 15
4
•WARNING: to avoid a hazard
due to instability, positioning or
fixing of the appliance must be
done in accordance with the
manufacturer instructions.
•WARNING: keep the appliance
ventilation openings clear of
obstruction.
• WARNING: do not damage the
appliance refrigerant circuit pipes.
• WARNING: Do not use
mechanical, electric or chemical
means other than those
recommended by the
Manufacturer to speed up the
defrost process.
• WARNING: Do not use or place
electrical devices inside the
appliance compartments if they
are not of the type expressly
authorised by the Manufacturer.
•WARNING: (if present) ice-
makers and/or water dispensers
not directly connected to the water
supply must be filled with potable
water only.
•WARNING: (if present)
automatic ice-makers and/or water
dispensers must be connected to a
water supply that delivers potable
water only, with main water
pressure between 0,17 and 0,81
MPa (1,7 and 8,1 bar).
Information: This appliance does
not contain CFCs.
•Appliances with Isobutane
(R600a): isobutane is a natural gas
without environmental impact, but
is flammable. Therefore, make
sure the refrigerant circuit pipes
are not damaged. Keep special
attention in case of damaged pipes
emptying the refrigerant circuit.
•C-Pentane is used as blowing
agent in the insulation foam and it
is a flammable gas. Pay special
attention during disposal
operations.
• This appliance is intended to be
used in household and similar
applications such as - staff kitchen
areas in shops, offices and other
working environments;
- farm houses and by clients in
hotels, motels and other
residential type environments;
- bed and breakfast type
environments;
- catering and similar non-retail
applications
• Do not store explosive
substances such as aerosol cans
with a flammable propellant in
this appliance.
• This appliance can be used by
children aged from 8 years and
above and persons with reduced
physical, sensory or mental
capabilities or lack of experience
and knowledge if they have been
given supervision or instruction
concerning use of the appliance in
a safe way and understand the
hazards involved.
• Cleaning and user maintenance
Important safety instructions
5
shall not be made by children
without supervision.
• To avoid the risk of children
becoming trapped and suffocating,
do not allow them to play or hide
inside the appliance.
• It must be possible to disconnect
the appliance from the power
supply by unplugging it if plug is
accessible, or by means of an
accessible multi-pole switch
installed upstream of the socket in
conformity with national safety
standards.
• Plug the appliance into a
grounding socket: the appliance
must be correctly connected to an
approved earthing system.
• Do not use single/multi adapters
or extension cords.
• During installation, make sure the
appliance does not damage the
power cable.
• Do not pull the aplliance power
cable
•The appliance must be handled
and installed by two or more
persons.
•Installation and maintenance
including replacement of the
supply cord must be carried out by
the manufacturer or a qualified
technician, in compliance with the
manufacturer’s instructions and
the local safety regulations in
force. In order to avoid a hazard
do not repair or replace any part of
the appliance including the supply
cord, unless specifically stated in
the user manual.
•This appliance can be used by
children aged from 8 years and
above and persons with reduce
physical, sensory or mental
capabilities or lack of experience
and knowledge if they have been
given supervision or instruction
concerning use of the appliance in
a safe way and understand the
hazards involved.
•Cleaning and user maintenance
shall not be made by children
without supervision.
•To avoid the risk of children
becoming trapped and suffocating,
do not allow them to play or hide
inside the appliance.
•It must be possible to disconnect
the appliance from the power
supply by unplugging it if plug is
accessible, or by means of an
accessible multi-pole switch
installed upstream of the socket in
conformity with national safety
standards.
•Plug the appliance into a
grounding socket: the appliance
must be correctly connected to an
approved earthing system.
•Do not use single/multi adapters
or extension cords.
•During installation, make sure the
appliance does not damage the
power cable.
6
•Do not pull the aplliance power
cable
•The appliance must be handled
and installed by two or more
persons.
•Installation and maintenance
including replacement of the
supply cord must be carried out by
the manufacturer or a qualified
technician, in compliance with the
manufacturer’s instructions and
the local safety regulations in
force. In order to avoid a hazard
do not repair or replace any part of
the appliance including the supply
cord, unless specifically stated in
the user manual.
1. Packing
The packing material is 100% recyclable and bears
the recycling symbol . For disposal, comply
with the local regulations. Keep the packing
materials (plastic bags, polystyrene parts, etc.) out of
the reach of children, as they are a potential source
of danger.
2. Scrapping/Disposal
The appliance is manufactured using recyclable
material.
This appliance is marked in compliance with
European Directive 2002/96/EC on Waste Electrical
and Electronic Equipment (WEEE). By ensuring
the correct disposal of this appliance, you can help
prevent potentially negative consequences for the
environment and the health of persons.
The symbol on the appliance, or on the
accompanying documents, indicates that this
appliance should not be treated as domestic waste
but must be taken to a special collection centre for
the recycling of electrical and electronic equipment.
When scrapping the appliance, make it unusable by
cutting off the power cable and removing the doors
and shelves so that children cannot easily climb
inside and become trapped.
Scrap the appliance in compliance with local
regulations on waste disposal, taking it to a special
collection centre; do not leave the appliance
unattended even for a few days, since it is a
potential source of danger for children.
For further information on the treatment, recovery
and recycling of this product, contact your
competent local office, the household waste
collection service or the shop where you purchased
the appliance.
Declaration of conformity
• This appliance has been designed for preserving
food and is manufactured in compliance with
Regulation (CE) No. 1935/2004.
• This appliance has been designed, manufactured
and marketed in compliance with:
- safety objectives of the “Low Voltage” Directive
2006/95/CE (which replaces 73/23/CEE and
subsequent amendments);
- the protection requirements of Directive “EMC”
2004/108/EC.
Safeguarding the environment
To ensure best use of your appliance, carefully
read the operating instructions which contain a
description of the product and useful advice.
Keep these instructions for future reference.
1. After unpacking the appliance, make sure it is
not damaged and that the door closes properly.
Any damage must be reported to the dealer
within 24 hours of delivery of the appliance.
2. Wait at least two hours before switching the
appliance on, to ensure that the refrigerant
circuit is fully efficient.
3. Clean the inside of the appliance before using it.
Before using the appliance
7
INSTALLATION
• Be careful not to damage the floors (e.g. parquet)
when moving the appliance.
• Make sure the appliance is not near a heat source.
• Install and level the appliance on a floor strong
enough to take its weight and in a place suitable
for its size and use.
• The appliance is arranged for operation in places
where the temperature comes within the following
ranges, according to the climatic class given on
the rating plate. The appliance may not work
properly if it is left for a long time at a
temperature outside the specified range.
• Make sure the voltage specified on the rating
plate corresponds to that of your home.
SAFE USE
• Do not store or use petrol, flammable liquids or
gas in the vicinity of this or other electrical
appliances. The fumes can cause fires or
explosions.
• Do not swallow the contents (non-toxic) of the ice
packs (in some models).
• Do not eat ice cubes or ice lollies immediately
after taking them out of the freezer since they
may cause cold burns.
• For products designed to use an air filter inside an
accessible fan cover, the filter shall be always in
position when the refrigerator is in function.
• Before carrying out any maintenance or cleaning
operation, unplug the appliance or disconnect it
from the power supply.
• Use the refrigerator compartment only for storing
fresh food and the freezer compartment only for
storing frozen food, freezing fresh food and
making ice cubes.
• Do not store glass containers with liquids in the
freezer compartment since they may break.
• Avoid storing unwrapped food in direct contact
with internal surfaces of the refrigerator or freezer
compartments.
• “The bulb used inside the appliance is specifically
designed for domestic appliances and is not
suitable for general room lighting within the
home (EC Regulation 244/2009)”.
The Manufacturer declines any liability for
injury to persons or animals or damage to
property if the above advice and precautions are
not respected.
Climatic Class Amb. T. (°C)
SN From 10 to 32
N From 16 to 32
ST From 16 to 38
T From 16 to 43
Precautions and general recommendations
•
Install the appliance in a dry, well ventilated room
far away from any heat source (e.g. radiator,
cooker, etc.) and in a place not exposed directly
to the sun. If required, use an insulating plate.
• To guarantee adequate ventilation follow
installation instructions.
• Insufficient ventilation on back of the product
increases energy consumption and decreases
cooling efficiency.
• The internal temperatures of the appliance may be
affected by the ambient temperature, frequency of
door opening, as well as location of the appliance.
Temperature setting should take into
consideration these factors.
• Allow warm food and drinks to cool down before
placing in the appliance.
• Do not obstruct the fan (if available) with food
items.
• After placing the food check if the door of
compartments closes properly, especially the
freezer door.
• Reduce to a minimum door opening.
• When thawing frozen food, place them in the
refrigerator. The low temperature of the frozen
products cools the food in the refrigerator.
• Appliances could have special compartments
(Fresh Food Compartment, Zero Degree Box,...).
In case not differently specified in the specific
booklet of product, they can be removed,
maintaining equivalent performances.
• Positioning of the shelves in the refrigerator has
no impact on the efficient usage of energy. Food
should be placed on the shelves in such way to
ensure proper air circulation (food should not
touch each other and distance between food and
rear wall should be kept).
• You can increase storage capacity of frozen food
by removing baskets and, if present, Stop Frost
shelve, maintaining an equivalent energy
consumption.
• Damaged gasket must be replaced as soon as
possible.
• High energy class products are fitted with
highefficiency motors that remain operational for
longer, but have a low power consumption. Do
not worry if the engine continues to run for longer
periods.
Energy-saving tips
8
Electrical connection for Great Britain and Ireland only
Warning - this appliance must be earthed
Fuse replacement
If the mains lead of this appliance is fitted with a
BS 1363A 13amp fused plug, to change a fuse in
this type of plug use an A.S.T.A. approved fuse to
BS 1362 type and proceed as follows:
1. Remove the fuse cover (A) and fuse (B).
2. Fit replacement 13A fuse into fuse cover.
3. Refit both into plug.
Important:
The fuse cover must be refitted when changing a
fuse and if the fuse cover is lost the plug must not
be used until a correct replacement is fitted.
Correct replacement are identified by the colour
insert or the colour embossed in words on the base
of the plug.
Replacement fuse covers are available from your
local electrical store.
For the Republic of Ireland only
The information given in respect of Great Britain
will frequently apply, but a third type of plug and
socket is also used, the 2-pin, side earth type.
Socket outlet / plug (valid for both countries)
If the fitted plug is not suitable for your socket
outlet, please contact After-sales Service for further
instruction. Please do not attempt to change plug
yourself. This procedure needs to be carried out by
a qualified technician in compliance with the
manufactures instructions and current standard
safety regulations.
Using for the first time
Connect the appliance to the power supply.
In models with electronics, a sound signal may be emitted, which means that the temperature alarm has
been activated: press the sound alarm off button. Where provided, position the antibacterial anti-odour
filter in the fan as demonstrated in the filter packaging.
Note: After turning the appliance on, you must wait for 4-5 hours for the correct storage temperature to be
reached for a normally filled appliance.
Clean the appliance occasionally with a cloth and a solution of warm
water and neutral cleaning agents specifically for cleaning the inside
of the refrigerator. Do not use abrasive cleaning agents. To ensure the
constant and correct flow of the defrosting water, regularly clean the
inside of the drain situated in the back wall of the refrigerator
compartment near the fruit and vegetable drawer using the utensil
provided (see figure).
Before carrying out any maintenance or cleaning, take the plug out of
the socket or disconnect the appliance from the power supply.
Maintenance and cleaning of the applicance
9
Replacing the light bulb or LED (depending on the model)
Always disconnect the appliance from the power supply before replacing the light bulb. Then follow the
instructions based on the type of light bulb for your product.
Replace the light bulb with one with the same features, available from the Technical Assistance Service and
authorised sellers.
Light type 1)
To remove the light bulb, unscrew it in an anti-clockwise direction, as
shown in the figure. Wait 5 minutes before reconnecting the appliance.
- traditional light bulb (max 25W)
or
- LED light bulb (with the same features)
only available from the Technical Assistance Service
Light type 2)
If the product has LED lights, as
demonstrated in the figures below,
contact the Technical Assistance
Service if you need a replacement.
LEDs last longer than traditional
light bulbs, improve internal
visibility and are environmentally-
friendly.
Light bulb
LED light bulb
In the event of non-use of the applicance
Disconnect the appliance from the power supply, empty it, defrost it (if necessary) and clean it.
Keep the doors slightly ajar to let air circulate inside the compartments. By doing this, you avoid the
development of mould and bad odours.
In the event of an interruption to the power supply
Keep the doors closed so the food stays cold for as long as possible. Do not re-freeze food that has partially
defrosted. If there is a prolonged power cut, the black out alarm may also activate (in products with
electronics).
Refrigerator compartment
The refrigerator compartment allows for the storage of fresh food and drink.
The refrigerator compartment defrosts completely automatically.
The occasional presence of drops of water on the internal back wall of the compartment is a sign of the
automatic defrosting phase. The defrosting water is channelled into a drain and then collected in a
container, where it evaporates.
10
Refrigerator compartment
Depending on the model, the product may be equipped with a special “Zero Degrees” compartment, which
is ideal for storing fresh meat and fish.
Warning: do not clean refrigerator accessories in a dishwasher.
Note: the ambient temperature, how often the doors are opened and the position of the appliance may
affect the internal temperatures in the two compartments. Set the temperatures depending on these factors.
Note: in very humid conditions, condensation may form in the refrigerator compartment, especially on the
glass shelves. In this case, it is recommended that you close containers with liquids in (e.g. a pot of stock),
wrap up food with a high water content (e.g. vegetables) and turn on the fan, if there is one.
Removing the fruit and vegetable drawer (depending on the model)
Pull the drawer outwards as far as it will go, lift it up and take it out.
To make it easier to remove the fruit and vegetable drawer, it may be necessary to empty (and possibly
remove) the two lower door shelves and then continue to remove the drawer.
Fan and antibacterial anti-odour filter (depending on the model)
The fan allows for the even distribution of the temperatures inside the compartments and, consequently,
better preservation of the food and reduction of excess humidity. Do not obstruct the ventilation area. The
fan can be turned on/off manually (see the Quick Guide); if it is turned on, it operates automatically when
necessary.
Freezer compartment
Model with separate freezer compartment
The freezer compartment allows for the storage of frozen food (for the period indicated on the
packaging) and the freezing of fresh food. The quantity of fresh food that can be frozen in 24 hours is
written on the rating plate. Arrange the fresh food in the freezing area inside the freezer compartment (see
Quick Guide), leaving enough space around the food packages to allow air to circulate freely. It is
advisable that you do not re-freeze food that has partially defrosted. It is important to wrap the food in a
way that prevents the ingress of water, humidity or condensation.
Making ice cubes
Fill 2/3 of the ice tray (if available) with water and put it back in the freezer compartment. Do not use
sharp or pointed objects to remove the ice under any circumstances.
Removing the drawers (depending on the model)
Pull the drawers outwards as far as they will go, lift them up and
remove them. To get more volume, the freezer compartment can be used
without the drawers.
Make sure that the door is closed properly after putting the food back
on the grilles/shelves.
Models with an internal product compartment
In the freezer compartment you can also freeze fresh food.
The quantity of fresh food that can be frozen in 24 hours is written
on the rating plate.
How to freeze fresh food:
• arrange the food on the grille, if present (figure 1), or directly on the
bottom of the compartment (figure 2)
• put the food in the middle of the compartment without it
coming into contact with food that is already frozen, keeping a
distance of about 20 mm (figure 1and 2).
figure 1
figure 2
11
For frost free models it is not necessary to carry out any defrosting procedures.
For other models, the build up of frost is a normal occurrence.
The quantity and speed of frost accumulation varies depending on the ambient conditions and how often
the door is opened. It is advisable to set the temperature colder or, if available, turn on the quick freeze
function (see Quick Guide) four hours before removing the food from the freezer compartment, to prolong
the preservation of the food during the defrosting phase. To defrost, turn the appliance off and remove the
drawers. Put the frozen food in a cool place. Leave the door open to allow the frost to melt. To prevent the
water from escaping during the defrost, it is advised that you place an absorbent cloth on the bottom of the
freezer compartment and wring it out regularly.
Clean the inside of the freezer compartment and dry it carefully.
Turn the appliance back on and put the food back inside.
How to defrost the freezer compartment (depending on the model)
STOP FROST SYSTEM (depending on the model)
The STOP FROST SYSTEM (available depending on the model) facilitates the defrost procedure for the
freezer compartment. The STOP FROST accessory (figure 1) is designed to collect some of the frost that
forms in the freezer compartment and it is easy to remove and clean, therefore reducing the time needed to
defrost the inside of the freezer compartment.
To remove the frost on the STOP FROST accessory follow the cleaning procedure demonstrated below.
- Open the freezer compartment door and remove
the upper drawer (figure 2).
- Unfasten the STOP FROST accessory (figure 3)
and remove it (figure 4), taking care not to drop
it on the glass shelf below.
Note: if the accessory is jammed or difficult to
remove, do not keep trying to remove it,
but proceed with the complete defrost of the
freezer compartment.
- Close the door to the freezer compartment.
- Remove the frost on the accessory by rinsing it
under running (not hot) water (figure 5).
- Let the accessory drip dry and dry the plastic
parts with a soft cloth.
- Reinsert the accessory by placing the back part
on the projections shown in figure 7-A, then
refasten the handle of the accessory to the clasps
above (figure 7-B).
- Reinsert the upper drawer and close the door to
the freezer compartment.
It is possible to clean the STOP FROST accessory
on its own without completely defrosting the freezer
compartment. Cleaning the STOP FROST
accessory regularly helps to reduce the need to
completely defrost the freezer compartment.
Note: the product specifications, including volume and energy, are calculated without the STOP FROST
accessory.
Procedure to clean the STOP FROST accessory
12
The “Zero Degrees” compartment is specifically designed to
maintain a low temperature and the correct humidity to preserve
fresh food for longer (for example, meat, fish, fruits and winter
vegetables).
Turning on and turning off the compartment
The internal temperature of the compartment is approximately 0° when the compartment is turned on.
To turn on the compartment, press the button
shown in the figure for more than one second
until the symbol lights up.
The lit symbol means that the compartment is
working. Press the button again for more than
one second to turn off the compartment.
To turn off the compartment completely, you must remove the drawer.
For the correct functioning of the “Zero Degrees” compartment, it is necessary that:
- the refrigerator compartment is turned on
- the temperature is between +2°C and +6°C
- the drawer in the “Zero Degrees” compartment must be inserted for it to be turned on
- one of the following special functions is not selected: Stand-by, Cooling-Off, Vacation (if present), in this
case, remove the food contained in it.
Note:
- if the symbol does not light up when you turn on the compartment, check that the drawer is properly
inserted; if the problem persists contact the authorised Technical Assistance Service.
- if the compartment is turned on and the drawer is open, the symbol in the control panel may
automatically turn off. The symbol will light up again when the drawer is inserted
- regardless of the state of the compartment, you may hear a faint noise, which you should consider as
normal
- when the compartment is not in operation, the temperature inside it depends on the general temperature of
the refrigerator compartment. In this case, it is advised that fruits and vegetables that are not sensitive to
cold (berries, apples, apricots, carrots, spinach, lettuce, etc.) are stored in it.
Important: if the compartment is turned on and food with a high water content is present, condensation
may form on the shelves. In this case, turn the function off temporarily.
Be careful when positioning food and containers that are small in size on the upper shelf of the “Zero
Degrees” compartment in order to prevent them accidentally falling between the shelf and the back wall of
the refrigerator compartment.
“Zero Degrees” compartment (depending on the model)
13
Removing the “Zero Degrees” compartment:
Carry out the following steps:
- to make it easier to remove the compartment, we recommend that you empty (and possibly remove) the
lower door shelves
- turn off the compartment
- remove the compartment by rotating it upwards
- remove the white plastic shelf under the compartment.
Note: it is not possible to remove the upper shelf and side supports.
To use the “Zero Degrees” compartment again, carefully reposition the white plastic shelf under the
compartment before inserting the drawer and turning the function back on.
To have a larger refrigerator volume and to reduce energy consumption, it is recommended that you turn
off the “Zero Degrees” compartment and remove the compartment.
Clean the compartment and its components occasionally using a cloth and a solution of warm water (taking
care not to submerge the white plastic shelf under the drawer) and neutral cleaning agents specifically for
cleaning the inside of the refrigerator. Do not use abrasive cleaning agents.
Before cleaning the compartment (also externally) it is necessary to remove the drawer to disconnect
the electrical supply for the compartment.
14
With the container on top, using the lid
as a base
With the container below
*with selected models
only
Haute cuisine*
Both Haute cuisine and Cheese box can be used for serving food at the
table. Do not use them in the freezer, microwave oven or on other heat
sources.
Do not chop food directly on the wooden surface as it may become scored.
Tips for cleaning:
Do not wash the wooden or plastic components in the dishwasher; we
recommend washing them by hand with mild detergent, without the use of
abrasive sponges.
Cheese box*
Haute cuisine can be used in 2 different positions
1. Wooden shelf
2. Bottle area
3. Container
lid
4. Container
Use of wooden accessories (if present)
15
Technical Assistance Service
Before contacting the Technical Assistance Service:
Restart the appliance to check if the problem has been solved. If not, disconnect the appliance again and
repeat the procedure after one hour.
If, after having completed the checks listed in the guide for malfunctions and after restarting the appliance,
your appliance continues to function incorrectly, contact the Technical Assistance Service, clearly
describing the problem and stating:
• the type of malfunction
• the model
• the type and serial number of the appliance
(written on the rating plate)
• the Service number (the number that is after the word SERVICE
on the rating plate placed inside the appliance).
Note:
Reversing the doors of the appliance, if carried out by the Technical Assistance Service, is not
considered as a warranty claim.
400010780180
Printed in Italy n
03/15
GB