Kokido EV01CBX/SPAKIT/22/EU User Manual
Displayed below is the user manual for EV01CBX/SPAKIT/22/EU by Kokido which is a product in the Pond & Pool Vacuums category. This manual has pages.
Related Manuals
RECHARGEABLE UNDERWATER VACUUM
USER MANUAL
GB
SAFETY WARNINGS & INSTRUCTIONS
Information contained in this Instruction Manual will help you operate the item safely, protect yourself
and others from hazards, and prevent damage to the device and other property.
SAVE THESE INSTRUCTIONS
WARNING!
- This is not a TOY. Children should be kept out of reach from this electric vacuum and its accessories.
- Never allow children to operate this product. Children shall not play with the product.
- Cleaning and user maintenance must not be carried out by children.
- You should not operate this electric vacuum when people/pets are present in the water.
- This electric vacuum is not intended for use by someone with reduced physical, sensory or mental capabilities, or a lack of experience and knowledge
unless they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
- Detachable supply unit (external adaptor).
- For the purposes of recharging the battery, only use the detachable supply unit (USB charger model number: HNAA050100E1 / HNAC050100B1)
that provided with this electric vacuum to charge the battery.
- Make sure the electric vacuum is fully immersed in water before initiating operation. The minimum water level required to operate the device must be
above the switching knob of the electric vacuum when it is held vertically. The product is only intended to be used underwater in a pool or spa; any
other use will void the warranty.
- Maximum operating depth in water is 2 meters (6.5 ft).
- Maximum water temperature: 5˚C (41˚F) – 42˚C (107.6˚F)
- Do not use this electric vacuum if any damage is detected.
- Replace damaged parts as soon as possible. Only use parts certified by the distributor or manufacturer.
- Make sure to connect USB charger to the power source through a residual current device (RCD)/ a ground fault circuit interrupter (GFCI). If in doubt,
consult a qualified, professional electrician.
- Disconnect the electric vacuum from the supply mains before carrying out any maintenance, such as cleaning the filter.
- The battery installed is a rechargeable Li-ion battery pack. Do not attempt to replace it yourself.
- This electric vacuum should only be charged with the included USB cable.
- DO NOT handle the electric vacuum while it is charging with wet limbs and without shoes.
- You should not operate this electric vacuum while the pool is being used.
- DO NOT use this electric vacuum without an intact filter cage in place, as the warranty will be voided as a result.
- Suction entrapment hazard: This electric vacuum generates suction. Do not allow hair, body, or any loose parts of your clothing to be in the suction
range of the electric vacuum during its operation.
- Never insert body parts, clothing, or other objects into the openings and moving parts of the electric vacuum.
- DO NOT use this electric vacuum to pick up any toxic substances, flammable, or combustible liquids such as gasoline, nor in the presence of
explosive or flammable fumes.
- Under no circumstances should you attempt to disassemble the electric vacuum and replace the impeller, motor, and battery by yourself.
- Never insert any object to make contact with the impeller.
- This electric vacuum shall not be used by children.
- The battery must be removed from the electric vacuum before it is scrapped.
- This electric vacuum contains battery that are only removed by skilled persons.
- The electric vacuum must be disconnected from the supply mains when the battery is being removed.
- For the battery disposal detail, refer to the section "Battery Disposal” in this manual
- The battery is to be disposed safely in accordance with local ordinances or regulations.
- Electric vacuum’s battery is a maintenance-free, rechargeable lithium-ion battery pack, which must be disposed properly. Recycling is required;
please contact your local authorities for more information.
CAUTION!
- DO NOT attempt to use the electric vacuum to clean anything other than your pool / spa.
- Use only original accessories delivered with this product.
- DO NOT use this electric vacuum right after pool-shocking. It is recommended to first let the pool circulate for at least 24-48 hours.
- Do not use this electric vacuum with another electric vacuum/cleaner simultaneously.
- Avoid picking up hard, sharp objects with this product. They may damage the electric vacuum and filter.
- Exercise caution when cleaning pool stairs.
- To avoid damaging the USB charging cable, do not carry the electric vacuum by the cable or tug the USB cable to disconnect it from
the power source and product.
- Charging must be done indoors, in a well-ventilated area away from sunlight, children, heat, ignition sources, and within an ambient
temperature range of 5˚C (41˚F) and 35˚C (95˚F).
- DO NOT leave the electric vacuum plugged in to the charger for over 10 hours.
- If the electric vacuum will not be used for an extended period, make sure it’s switched off and use a damp cloth to clean and dry it and
its accessories. Make sure to charge the electric vacuum to about 30% to 50% of the battery capacity before it is stored. Store in a
well-ventilated area away from sunlight, heat, ignition sources, pool chemicals, and children. Recharge the electric vacuum every
three months.
Above warnings and cautions are not intended to incorporate all possible instances for risks and / or severe injuries.
Pool / spa owners should always exercise extra caution and common sense when utilizing the product.
How to remove the battery pack for battery disposal only
(To be carried out by an authorized technician)
Recommended tools (not included):
Philips screwdriver and small slot screwdriver
1. Use the screwdriver to unfasten the 2 side screws
to release the front portion and then detach it from
the main body.
2. Unfasten the 4 screws as shown and then remove
the front chamber to expose the enclosure inside.
3. Unfasten the 2 screws as shown to release the
module. Move it to the opening of the chamber.
4. Detach all 4 cable connectors by pressing on
the clip and detach it simultaneously. Remove
the whole module out of the chamber to expose
the battery. Remove the battery and wrap its
connector end with insulating tape in order to
avoid short circuit caused by the contact of both
wire terminals.
SAVE THESE INSTRUCTIONS
Manufacturer: Kokido Development Limited.
Unit 1319, Sunbeam Centre,
27 Shing Yip Street, Kwun Tong, Kowloon, HK
If soft copy of this instruction manual is required,
please contact our customer
service by email: customerservice@kokido.com
TROUBLESHOOTING
Problem
Electric vacuum does
not capture the debris
Debris escapes from the
filter
Electric vacuum cannot
be charged / recharged
Charging time is longer
than advertised
Pivoting suction head
(if provided) does not
move smoothly
Possible Cause
Battery is drained
Impeller is jammed
Impeller is broken
Filter cage is full
One-way valve is
damaged
Filter cage is damaged
Battery is damaged
USB cable is damaged
USB charger is out of
order
Stained charging pins
Wheel is jammed
Solution
Charge the battery again.
Power off the electric vacuum and inspect the middle gap of the electric vacuum
to see if the impeller is jammed by larger debris. If possible, use a small tool to
remove it with intensive care & caution. If necessary, contact your dealer for
further instructions.
WARNING! Make sure the electric vacuum is powered off when the
unit is being serviced.
Contact an authorized dealer regarding replacements.
Clean the filter cage.
One-way valve works like a door to prevent the debris from escaping from the
filter. Contact dealer for replacement part and instructions.
Replace with a new filter cage.
Contact an authorized dealer regarding replacements.
Contact an authorized dealer regarding replacements.
WARNING! DO NOT open the electric vacuum and replace the battery
by yourself. This could result in severe or fatal injuries, as well as voiding
the warranty.
Replace with a new USB cable.
Replace with a new USB charger.
The stains can be removed by using a cotton bud soaked with juice of lemon or
vinegar to clean the areas around the charging pins.
Clean out the debris from the wheel.
Note: Do not attempt to take out the wheels.
Environmental Programmes, WEEE European Directive
Please respect the European Union regulations and help to protect the environment.
Return non-working electrical equipment to a facility appointed by your municipality that properly
recycles electrical and electronic equipment. Do not dispose them in unsorted waste bins.
For items containing removable batteries, remove batteries before disposing of the product.
© 2021 Kokido Development Ltd. 21007015
All rights reserved. No part of this document may be reproduced or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording,
or otherwise, without prior written permission of Kokido Development Ltd. (V2)
EV01/22
Made in China
Fig.2
Fig.1
Locking position Releasing position
GETTING STARTED
Charging the battery
IMPORTANT NOTE: Fully charge the electric vacuum for 6 hours before using it for the first time.
OPERATION
Immerse the electric vacuum into water until water level reaches the switching knob.
Follow the direction of marking “ I ” to switch the knob clockwise until it comes to a
halt (you will hear a ‘click” and a green dot will be exposed), the electric vacuum will
begin to work immediately.
EMPTYING THE FILTER
WARNING! Using the electric vacuum without a filter cage in place will VOID your warranty.
In order to maximize the cleaning efficiency of the cleaner, be sure to clean the filter cage before and after each use.
CAUTION! If the electric vacuum is charging, disconnect the USB charger from the power source and detach the electric vacuum
from the USB charging cable before making any attempts to clean it.
Emptying filter cage
1. Press side tabs simultaneously and remove the
suction nozzle from the tube collar. (Fig.1)
2. Grasp the plastic area at the base of the filter cage
(DO NOT GRASP THE FILTER CAGE SCREEN).
Pull to remove it from the suction nozzle. (Fig.2)
Rinse the filter cage with water to remove any debris caught inside.
If brushing is deemed necessary, use only a soft brush to clean it
gently and carefully.
3. Install the filter cage back to suction nozzle. Reverse the steps in point 2 to re-install the filter cage to the suction nozzle. Make sure to
align the raised notches on the inside of the filter cage opening to the notches under the suction head at first.
4. Insert the suction nozzle (installed with filter cage) into the tube collar until it is in a locking position. You will hear a “click” sound.
CAUTION! Replace a damaged filter bag / filter cage with a new one before initiating the next operation.
MAINTENANCE & STORAGE
NOTE:
1.Be sure to clean and dry the areas around the charging port and charging pins after every use to avoid the forming of stains (byproduct of
a natural chemical reaction between electric current and water). Otherwise, the stains can be removed by light scrubbing with a cotton bud
soaked with juice of lemon or vinegar.
2.
Battery discharges on its own during storage. The battery should be stored at room temperature, charged to about 30% to 50% of its capacity.
3.You must recharge the battery at least once every three months if it is not frequently used.
•Disconnect all USB charging peripherals.
•Detach all accessories from the electric vacuum. If necessary, rinse the electric vacuum and accessories with fresh water. DO NOT use
detergent.
•Be sure to drain the water from the electric vacuum before storing it.
•Use a damp cloth to clean and dry the electric vacuum and its accessories.
•Store them in a well-ventilated area away from the sunlight, children, heat, ignition sources, and pool chemicals. Ambient temperature for
storage should be 10˚C – 25˚C (50˚F – 77˚F). NOTE: A higher temperature may reduce the battery life during storage.
WARNING!
- Under no circumstances should you attempt to disassemble the electric vacuum and replace the impeller, motor and battery
by yourself.
CAUTION!
• Excessive heat can damage the battery and reduce the lifespan of your electric vacuum as a result.
• Consult your dealer regarding battery replacement if the following happens:
- Battery appears damaged or will not charge fully.
- Battery operation time is noticeably reduced. Observe and record the run times of the first few operations (on a full charge). Use these
run times as a reference point to compare with run times of older batteries.
• The battery must be removed from the electric vacuum before it is scrapped.
• The electric vacuum must be disconnected from the supply mains when the battery is being removed.
• The battery is to be disposed safely in accordance with local ordinances or regulations.
NOTE: Incorrect maintenance may reduce the battery life and affect its capacity as a result.
BATTERY DISPOSAL (To be carried out by authorized technician)
Your electric vacuum’s battery is a maintenance-free, rechargeable lithium-ion battery pack, which must be disposed properly. Recycling is
required; please contact your local authorities for more information.
WARNING!
Never attempt to disassemble a battery pack
• Be sure to remove all personal items such as rings, bracelets, necklaces, and watches before you unwire the battery pack from
the electric vacuum.
• A battery can produce a short circuit current high enough to weld a ring (or similar items) to metal, potentially causing a severe
burn in the process.
• Wear complete eye protection, gloves, and protective clothing before you remove the battery pack.
• Avoid touching the wires altogether and avoid allowing them to make contact with any metal items, which could cause sparking
and/or short-circuit the battery.
• Never smoke or allow a spark or flame in the vicinity of the battery or the electric vacuum.
• Do not expose the battery to fire or intense heat as this may result in an explosion.
CAUTION!
If a battery leak occurs, avoid contact with the leaking fluids and place the damaged battery in a plastic bag.
- If leaking fluids come in contact with skin and clothing, wash immediately with plenty of soap and running water.
- If leaking fluids come in contact with eyes, immediately flush them with cool, running water for at least 15 minutes and do not rub them.
Seek medical attention immediately.
CAUTION
• DO NOT cover the side slot (middle gap) of the electric vacuum during operation,
the impeller / motor may be damaged otherwise.
• Remove the electric vacuum from the pool/spa as soon as cleaning is complete.
CAUTION! Make sure the electric vacuum is always pointing downwards when it is placed into the pool. Otherwise, the pole connector may
be bent and damaged as a result.
To retrieve the electric vacuum from the pool / spa, lift the electric vacuum while pointing it downwards in order to allow water to discharge.
Rinse the electric vacuum with fresh water after every use. DO NOT use any detergent.
1. Place the unit on a flat surface. Set the vacuum to
Power Off/ Charging position by turning the switching knob
anticlockwise until it stops and completely exposes the
charging port. Align and insert the USB charging cable into
the charging port.
2. Connect the USB charging cable to the USB charger, then plug the USB charger into the power source.
Once the electric vacuum begins to charge, the indicator light will turn red. Normally, it takes about 4.5 - 6 hours
to reach a full charge. The indicator light will turn green once the electric vacuum is almost fully charged.
NOTE
• Always disconnect the USB charger from the power source as soon as charging is complete.
•
Immediately turn the power off and disconnect the
USB charger
from the power source if you detect any of the
following conditions:
- Offensive or unusual odor
- Excessive heat
- Deformation, cracks, leaks
- Smoke
3. When charging is complete, disconnect the USB charger from the power source and unplug the USB cable
from the USB charger and electric vacuum.
Normally, the electric vacuum can operate up to 30 minutes on a full charge (after 4.5-6 hours of charging)
Note: Clean the filter regularly. Excessive debris inside the filter will increase burden to the motor operation and
shorten the operating duration as a result.
NOTE: Rechargeable lithium-ion battery is classified as a consumable item. It has a limited life and will gradually
lose its capacity to hold a charge. Therefore, the running time of the electric vacuum will gradually reduce after
repeated charging and discharging throughout its product life.
Once the lifespan of the battery reaches its end, refer to section “BATTERY DISPOSAL” for instructions regarding
battery disposal.
NOTE: Let the electric vacuum rest for 30 to 40 minutes before charging it again.
Pool Preparation
- If the liner is brittle, damaged, or wrinkled, contact a qualified professional to perform the necessary repairs or
perform a liner replacement prior to using the pool vacuum.
- If you are using a saltwater pool, make sure all salt are dissolved before placing the pool vacuum into the water.
WARNING!
•Do not use the USB charging cable / USB charger if any damage is detected.
•Make sure both the electric vacuum and the charging port are clean and dry before charging them. TIPS : use a
cotton bud to dry the charging port and charging pins)
• The charging pins are waterproof. However, remnants of water in the port and around the pins could result in
natural occurrence of stains (a byproduct of chemical reaction between water and electric currents). Otherwise,
the stains can be removed by light scrubbing with a cotton bud soaked with juice of lemon or vinegar.