Table of Contents
KYOCERA P7040cdn User Manual
Displayed below is the user manual for P7040cdn by KYOCERA which is a product in the Laser Printers category. This manual has pages.
Related Manuals
KYOCERA
COMMAND CENTER
Operation Guide
Legal and General Information
Notice
Unauthorized reproduction of all or part of this guide is prohibited. The information
in this guide is subject to change without notice.
Kyocera Mita cannot be held liable for any problems arising from the use of this
product, regardless of the information herein.
Regarding Trademarks
KYOCERA, KYOCERA MITA, ECOSYS and PRESCRIBE are registered
trademarks of Kyocera Corporation.
KPDL and KIR (Kyocera Image Refinement) are trademarks of Kyocera
Corporation.
Microsoft, Windows and Windows NT are registered trademarks of Microsoft
Corporation.
Apple, AppleTalk, Mac, Macintosh, Mac OS and TrueType are registered
trademarks of Apple Computer, Inc. Bonjour is a trademark of Apple Computer,
Inc.
Adobe, Acrobat and Postscript are registered trademarks of Adobe Systems
Incorporated.
Novell and NetWare are registered trademarks of Novell, Inc.
HP and PCL are registered trademarks of Hewlett-Packard Company.
Intel, Pentium and Celeron are registered trademarks of Intel Corporation.
Other brand and product names contained in this document are registered
trademarks or trademarks of their respective companies.
General Information
When using this utility, the items that can be configured will differ depending on
the model of your printer or multifunctional printer (hereinafter referred to as
"printing system"); or whether it supports color printing or not.
Examples in this document are described in terms of the Internet Explorer 6.0 and
Microsoft Windows XP operating system environment.
1 Introduction.............................................................................. 1
Using COMMAND CENTER ............................................................... 1
System Requirements ......................................................................... 1
2 Access ...................................................................................... 2
Accessing COMMAND CENTER ........................................................ 2
Admin password.................................................................................. 2
Authentication...................................................................................... 2
Encryption ........................................................................................... 2
3 COMMAND CENTER Pages .................................................... 3
Start Page ........................................................................................... 3
Basic Page .......................................................................................... 7
Printer Page ...................................................................................... 16
Scanner Page.................................................................................... 19
FAX / i-FAX Page .............................................................................. 21
Jobs Page ......................................................................................... 33
Document Box Page ......................................................................... 33
Advanced Page ................................................................................. 36
4 Troubleshooting .................................................................... 56
Table of Contents
Introduction
Operation Guide 1
1 Introduction
Using COMMAND CENTER
KYOCERA COMMAND CENTER (hereinafter referred to as COMMAND CENTER)
refers to the web home page that is installed in the machine from which you can verify
the operating status of the machine and make settings related to security, network
printing, E-mail transmission and advanced networking.
System Requirements
Protocol
COMMAND CENTER operates in the following environment. Check the following before
use.
• The TCP/IP protocol is installed in the PC.
• An IP address is assigned to the printing system.
Web browser
• Microsoft Internet Explorer 6.0 or later *1
• Mozilla Firefox 1.5 or later
• Safari 2.0 or later *2
*1: Microsoft Internet Explorer operates on Microsoft Windows 98SE/Me/2000/XP/
Vista/7, Microsoft Windows NT 4.0, and Microsoft Windows Server 2003/2008.
*2: Safari operates on Apple Macintosh OS X 10.4 or later.
Access
2KYOCERA COMMAND CENTER
2 Access
Accessing COMMAND CENTER
1. Run the web browser.
2. In Address or Location, enter the machine IP address as the URL,
e.g. http://192.168.10.150/.
Select a category from the navigation bar on the left to view and set values for that
category.
Admin password
Setting Administrator Password restricts general users' access to pages other than
the Start page. For security purposes, setting the Administrator password is highly
recommended. With some models, the default Administrator password is factory-set
as admin00.
The Login button is displayed at the upper left of the screen. To access a page other
than the Start page, click Login. (This button may not be displayed on some models.
When this button is not displayed, click a page other than the Start page.) The password
input window is displayed. Entering the predefined administrator password allows the
user to access all pages.
For how to define the administrator password, refer to Basic > Security > Account
Settings on page 12.
Authentication
Setting Authentication allows only the predefined users to access pages. In addition,
you can discriminate users by giving either the General User or Administrator privilege
to each user. Before using the authentication function, you have to define those users.
For how to define users, refer to Basic > Security > User Login on page 14.
When a user sets authentication and accesses COMMAND CENTER, only the Start
page is displayed. The Login button is displayed in the upper left of the screen. Click it
to log in. When the user logs in with an Administrator account, hidden pages are
displayed and can be accessed. When the user logs in with a General User account,
the user can access the user's account page on Basic > Security > User Login and the
user’s settings on the basic page and the user's document box and shared document
box pages.
The authentication function come in two types: Local Authentication and Network
Authentication. For more information, refer to Advanced > Management >
Authentication > General on page 48.
Encryption
You can encrypt communication between a PC and this machine using SSL encryption.
When this encryption is enabled, the access URL must be specified as "https://..." For
details on the setting procedure, refer to Advanced > Security > Secure Protocols on
page 51.
COMMAND CENTER Pages
Operation Guide 3
3 COMMAND CENTER Pages
The COMMAND CENTER home page divides the following functions onto separate
pages. You can jump to the desired pages by clicking the tab located at the top of each
page. The following is an outline of each page accessed.
Start Page
The following operations are possible from the Start page.
• Verifying the machine’s operating status
• Logging in or out during setting of the administrator password
• Changing the language that COMMAND CENTER is displayed in
• Verifying various settings (machine, printing, FAX, scanning, network and E-mail)
• Verifying the number of scanned pages and the number of prints made on the
machine
• Access linked home pages
All users will have access to the Start page.
Page Description
Start This page allows you to verify this machine’s operating status and
current settings.
Basic This page includes settings that apply to the entire machine, such
as Device Defaults, Security, and Basic Networking.
Printer This page includes settings that apply to the printing function of the
machine, such as Default Print Resolution and Copy Count.
Scanner
This page includes settings that apply to the scanning function of the
machine, such as Default Scan Resolution and Original Placement.
FAX / i-FAX
This page includes settings that apply to the FAX function of the
machine, such as FAX transmit and receive settings.
Jobs This page includes information on all device jobs including job
status, scheduled job and job log.
Document
Box
This page allows you to add and delete a document box, and
delete documents within a document box.
Advanced This page includes advanced settings that apply to the entire
machine and is comprised primarily of advanced network settings.
COMMAND CENTER Pages
4KYOCERA COMMAND CENTER
Start > Start
This page allows you to verify the machine’s operating status. This will be the first screen
that appears after COMMAND CENTER has been started up.
Start > Status Pages
These pages allow you to verify the various settings (machine, printing, scanning, network
and E-mail) that were made on the operation panel or using COMMAND CENTER.
It is divided by the following items.
-Network
- Security
- Device/Printer
- Scanner
- FAX / i-FAX
- Jobs
- Counters
Item Description
Select
Language
Appears if COMMAND CENTER pages support multiple
languages.
To change COMMAND CENTER language:
1. Open the Select Language drop down list by clicking it.
2. Select the appropriate language.
If you attempt to view COMMAND CENTER with a character
set other than the language that is used on the operation
panel’s display, some characters may be illegible.
Operation Panel This indicates the machine’s operating status as displayed
on the operation panel. To update the display to the most
recent status, click the Refresh button.
Toner Level
This shows the approximate level of remaining toner. The closer
the value to 0%, the smaller the amount of remaining toner. If
you use non-original toner kit, the toner gauge measurement
will not be indicated correctly.
Network IP
Information
Network IP information on the printing system is displayed.
This allows you to verify the following information:
- IP Address
- IPv6 Address (Manual)
- IPv6 Address (LinkLocal)
- IPv6 Addresses 1 to 5 (Stateless)
- IPv6 Address (Stateful)
-Host Name
System
Identification
System information on the printing system is displayed. This
allows you to verify the following information:
- MAC Address
- System Firmware
- Engine Firmware
- Panel Firmware
- FAX Firmware
- Serial Number
-Asset Number.
Media Input
This shows paper size and media type for cassettes and MP tray.
COMMAND CENTER Pages
Operation Guide 5
Item Description
Network >
General
This allows you to verify the current settings for LDAP, TCP/
IP, IPP, IPP over SSL, AppleTalk, NetBEUI, IPv4, and IPv6.
For more information, refer to Advanced Page on page 36.
Network > IP
Filters
This displays the list of IP addresses and subnet masks
(IPv4) or prefix length (IPv6) that have access permission as
set under IP Filters (IPv4) and IP Filters (IPv6) on the
Advanced page. If no IP addresses have been designated,
then access permission will be granted to all addresses.
For more information, refer to Advanced > Protocols > TCP/
IP > IP Filters on page 38.
Network >
SNMP
This allows you to verify the settings made under SNMPv1/
v2 and SNMPv3 on the Advanced page.
For more information on SNMPv1/v2, refer to Advanced >
Management > SNMP > SNMPv1/v2c on page 45.
For more information on SNMPv3, refer to Advanced >
Management > SNMP > SNMPv3 on page 46
Network >
POP3/SMTP
This allows you to verify the E-mail-related settings made on
POP3 and SMTP pages of the Advanced page.
For more information on POP3, refer to Advanced > E-mail >
POP3 > General on page 44.
For more information on SMTP, refer to Advanced > E-mail >
SMTP > General on page 42.
Network >
Logical Printers
This allows you to verify the settings made on the Logical
Printers page of the Advanced page.
For more information, refer to Advanced > Protocols > TCP/
IP > Logical Printers on page 39.
Network >
Netware
This allows you to verify the settings made on the Netware
page of the Advanced page.
For more information, refer to Advanced > Protocols >
Netware on page 40.
Security This allows you to verify the current settings for secure
protocols, IEEE802.1x, and IPSec. To change the settings:
For secure protocols, refer to Advanced > Security > Secure
Protocols on page 51; For IEEE802.1x, refer to Advanced >
Security > IEEE802.1x on page 52; For IPSec, refer to
Advanced > Security > IPSec > Rule1 (to Rule3) on page 53.
Device/Printer This allows you to verify the settings made on the Basic and
the Printer pages.
For more information, refer to Basic Page on page 7 and
Printer Page on page 16.
Device/Printer >
APL. Filter
This allows you to verify the settings made on the Basic and
the Printer pages.
For more information, refer to Printer Page on page 16.
Device/Printer >
APL. Filter
Parameters
This allows you to verify the settings made on the Basic and
the Printer pages.
For more information, refer to Printer Page on page 16.
Scanner This allows you to verify the settings made on the Scanner
page.
For more information, refer to Scanner Page on page 19.
COMMAND CENTER Pages
6KYOCERA COMMAND CENTER
Start > Information
This page provides information about the Address Book, User Login, the model number
of the machine and version of firmware.
Start > Links
Links to the Kyocera Mita Corporation web site. Visit the following web site for more
information and downloads.
FAX / i-FAX >
General
This allows you to verify the settings made on the
FAX / i-FAX
page.
For more information, refer to FAX / i-FAX Page on page 21.
FAX / i-FAX >
FAX
FAX / i-FAX > i-
FAX
Jobs > Printing
Jobs Log
This allows you to confirm the log of the jobs in each operation.
For more information, refer to Jobs Page on page 33.
Jobs > Sending
Jobs Log
Jobs > Storing
Jobs Log
Counters >
Printed Pages
This allows you to verify the accumulated number of printed
pages for each paper size and color (Monochrome, Mono
Color, and Full Color). A page printed on both sides, an A3-
sized sheet of paper, or a page larger than Ledger size is
counted as two pages.
Counters >
Scanned Pages
Provide information of the number of pages copied, faxed,
and other (scanned), respectively.
Item Description
Item Description
Address Book
This page provides information about the maximum and
current numbers of addresses possible to add to the private
and group Address Books. For more information, refer to
Basic > Defaults > Address Book > Groups on page 11 and
Basic > Defaults > Address Book > Groups on page 11.
User Login
This shows the
number of registered users
. For more
information, refer to Basic > Security > User Login on page 14.
About The model number of this printing system and Version of
Firmware can be confirmed.
Item Description
Download
Drivers
http://www.kyoceramita.com/download/
COMMAND CENTER Pages
Operation Guide 7
Basic Page
This section includes settings that apply to the machine, such as Device Defaults,
Security, and basic Networking.
Basic > Defaults > Network
This page allows you to make the settings that are required for network printing and
sending E-mail. For more information, refer to Advanced > Protocols > TCP/IP >
General on page 37.
You must restart this machine after you have completed these settings in order to
properly register the content of those settings in the machine. Refer to Basic > Defaults
> Reset on page 9.
Kyocera Online http://www.kyoceramita.com/
Item Description
Item Description
Host Name Specifies a name for the printing system network
component. This name is used as the NetBEUI printer name
and as the WSD device name.
LAN Interface
Specifies the communication rate from
Auto
,
10BASE-T-Half
,
10BASE-T-Full
,
100BASE-TX-Half
, and
100BASE-TX-Full
.
IPv4 Settings
DHCP/
BOOTP
Specifies whether or not to obtain an IP address using
DHCP or BOOTP.
IP Address
(IPv4)
Assigns the Internet Protocol address on the printing system
network component. Format of the IP address is four-byte
(32-bit) numbers separated by dots, e.g. 192.168.110.171.
Subnet
Mask
Specifies the subnet mask of the hosts or network with which
the print system is connecting. If you have manually
assigned an IP address that starts with a number between
192 and 223, it is recommended that you set the subnet
mask to "255.255.255.0."
Default
Gateway
Specifies the IP address of the default gateway.
IPv6 Settings
IPv6 Specifies whether or not to enable the IPv6 protocol.
Select On to use the IPv6 protocol.
IP
Address
(IPv6)
Assigns an IPv6 address to the printing system network
component. The format of the IPv6 address is a sequence of
numbers (128 bit in total) separated by colons, e.g.
2001:db8:3c4d:15::1a2c:1a1f.
Prefix
Length
Specifies the IPv6 prefix length of the hosts or network with
which the print system is connecting.
COMMAND CENTER Pages
8KYOCERA COMMAND CENTER
Basic > Defaults > Time
If a time server is used to synchronize the time as well, the current time can be adjusted
regularly and easily. Enter the IP address of the time server and click the Synchronize
button.
Time information is required when you receive reports from this machine via E-mail. It
is recommended that you set the time when the report mail function is enabled.
RA
(Stateless)
Select On to use RA to configure IPv6 addresses.
Default
Gateway
Specifies the IPv6 address of the default gateway.
DHCPv6 Specifies whether or not to obtain IPv6 IP addresses by
automatic configuration. When RA is turned On, the IP
addresses and server information are obtained via DHCPv6
based on the settings of the automatic configuration made
under RA (router setting).
Item Description
Item Description
Current Local
Time
Displays the time that is currently set in the machine.
Current
Universal Time
(UTC/GMT)
Displays the Greenwich Mean Time that is currently set in
the machine.
Time Zone Sets a time difference. Click the drop down list and select
your region.
Summer Time Switches the Summer Time setting On and Off. Select On in
order to have the Summer Time function applied when the
time is synchronized with a time server.
Time Server Enter the host name or IP address of the time server from
which you want to acquire the time.
Synchronize
with Time
Server now
Click the Synchronize button to synchronize the registered
time with the designated timer server.
Synchronization
Status
Displays the results of the synchronization operation with the
time server.
COMMAND CENTER Pages
Operation Guide 9
Basic > Defaults > Reset
This page allows you to restart the machine in order to make all settings in the machine
valid. It is also possible to select to have all settings returned to their factory default
values.
Basic > Defaults > Device Defaults
This page allows you to change the language that is used in the display, as well as to
turn the Auto Sleep Mode On or Off.
Item Description
Restart entire
device
Clicking Restart restarts this machine.
Restart Network Clicking Restart allows restarting the network interface
without restarting the machine.
The network interface must be restarted whenever a change
has been made to the network settings.
Reset entire
device to
factory default
When clicking the Reset button, the machine returns to the
factory default settings. However, the document box,
address book, user information, logs, and certificates are not
deleted.
Item Description
Operation Panel
Language
You can select the language of the messages on the display
by following the procedure given below. The following
languages are available for selection in the drop down list:
English, Français, Deutsch, Italiano, Nederlands, Español,
Português, Russian, and the downloaded languages
You can optionally download messages in other languages.
Contact your dealer for information.
Some models may require restarting after configuration.
Sleep Timer Specifies the time from 1 to 240 minutes after which the
system enters the auto sleep mode.
You can turn the sleep timer On or Off as follows. The
default setting is On.
1. Click Advanced on the right hand side of the drop down
list.
2. Turn the sleep mode On or Off.
3. Click Submit.
Low Power
Timer
Specifies the time from 1 to 240 minutes after which the
system enters the low power mode, where it reduces the
power consumption.
Override A4/
Letter
Specifies whether or not the A4 and Letter size paper should
be interchangeable.When turned On, for example, if the A4
paper is not in the tray, the Letter size paper will be selected
for printing.When turned Off, the Letter size paper will not be
used in place of the A4 paper, when A4 is selected for
printing but the A4 tray is empty.
Auto Error Clear
Specifies whether or not to clear errors automatically when
they occur.
COMMAND CENTER Pages
10 KYOCERA COMMAND CENTER
Basic > Defaults > Address Book > Contacts
This page allows you to add, edit or delete Contacts.
Adding a New Contact
1. Open the Address Book Contacts page.
2. Click Add Contact. The Address Book Contacts - Add page opens.
Error Clear Timer
Specifies the time between 5 and 495 seconds after which
errors are cleared automatically.
RAM Disk Mode
Specifies whether to use a part of the print system memory
as a RAM disk. You can specify the size of the print system
memory to use for the RAM disk. If this item is On, electronic
sorting is enabled and the printing speed increases. After
you have changed the setting, you must restart the printing
system.
RAM Disk Size
Specifies the size of the RAM disk. For allowable sizes, refer
to the print system operation guide. After you have changed
the setting, you must restart the printing system.
Interrupt Clear
Time
This determines the time of period before the machine
reverts to normal mode, after the interrupt copy mode has
been engaged. The range is 5 to 459 seconds (in 5-second
increments).
WSD Scan Timer
This determines the time of period before the machine
reverts to normal mode, after WSD scan mode has been
engaged. The range is 10 to 495 seconds (in 5-second
increments).
File Name
You can change the file name for the scan data or the job
name for the jobs on the Job page.
Additional
Information
You can add a Job Number or the Data and Time to the File
Name designated above. The additional information varies
depending on model.
MP Tray Empty
With the MP tray set as the default paper source, this
enables (On) or disables (Off) the paper empty message
when the MP tray becomes empty.
Unusable Time
Setting
This restricts use of the machine by time of day. When
turned On, the machine becomes unoperative during the
time of day specified by Unusable Time. Except, the
received FAXes are stored in the machine and printed after
the unusable time period has been expired.
Unusable Time
This determines the time of period during which the machine
is restricted for use. This is enabled when Unusable Time
Setting is On.
Unlock Code
Entering this code, comprised of four digits from 0 to 9,
temporarily allows the machine to be usable during the time
of period of restriction.
Item Description
COMMAND CENTER Pages
Operation Guide 11
3. Enter the information for the address to be registered. You can specify a FAX number
and i-FAX address even if the FAX System is not installed.
4. Click Submit.
Editing a Contact
1. Open the Address Book Contacts page.
2. Click the number or name of the address to edit.
The Address Book Contacts - Edit page appears.
3. Modify the information of the address.
4. Click Submit.
Deleting a Contact
1. Open the Address Book Contacts page.
2. Check the desired contact. When the check box on the left side of Number is selected,
all contacts displayed on the page will be checked.
3. Click Delete Contact.
The Address Book Contacts - Delete page appears. You can confirm the addresses
to be deleted
4. Click Delete when the desired addresses are selected.
Basic > Defaults > Address Book > Groups
This page allows you to add, edit or delete Groups.
Adding a New Group
1. Open the Address Book Groups page.
2. Click Add Group.
The Address Book Groups - Add page opens.
3. Enter the number and name of the group.
4. Click Submit.
The Address Book Groups - Add Members page opens.
5. Select the members to be added to the created group.
Check the members you want to add. The members must be registered before added.
6. After you have selected the members, click Submit.
The Address Book Groups - Edit page opens. Click Submit. You can continue editing
groups, such as changing group names and adding or deleting members.
Editing a Group
1. Open the Address Book Groups page.
2. Click the number or name of the group to edit.
The Address Book Groups - Edit page opens.
COMMAND CENTER Pages
12 KYOCERA COMMAND CENTER
3. You can change the number or name of the group and add or delete members.
To add members, click Add Members and select the addresses to add. Click Submit.
The members must be registered before added.
4. Click Delete when the desired members are selected.
5. After you have finished editing, click Submit.
Deleting a Group
1. Open the Address Book Groups page.
2. Check the desired group. When the check box on the left side of Number is selected,
all groups displayed on the page will be checked.
3. Click Delete Group.
The Address Book Groups - Delete page appears. You can confirm the group to be
deleted.
4. Click Delete when the desired group is selected.
Basic > Security > Account Settings
The Administrator (Admin) account is the master access account. It controls access to
the printer and networking configuration from all setup and management utilities
including the HTML web pages.The Admin password set in the following is valid when
Authentication is set to Off. For details on Authentication, see Advanced >
Management > Authentication > General on page 48.
Setting the Admin password is highly recommended to prevent unauthorized changes
to the machine and networking configuration. With some models, the default
Administrator password is factory-set as admin00. It is recommended to periodically
change password.
To change the password:
1. Enter the Old Password.
2. Enter the password you want to set in New Password. This can be up to 32 (30 with
some models) character long.
3. Enter the same password in Confirm New Password.
4. Click the Submit.
COMMAND CENTER Pages
Operation Guide 13
Basic > Security > Device Security > General
This page allows you to restrict access from the operation panel or USB host device. In
addition, an explanation about each security setting is displayed.
Basic > Security > Device Security > Interface Block
This page allows you to restrict access from each interface.
Item Description
Lock Operation
Panel
Restricts access from the operation panel. With some
models, this setting is irrelevant if the user has logged in as
the Administrator.
When it is set to
Lock
(
Block
), use of the
System menu
on this
machine, registration in and editing of the Address Book and
Box, use of the Stop key, and cancellation of jobs are forbidden.
When it is set to
Partial Lock
, use of the
System menu
on
this machine and registration in and editing of the Address
Book and Box are forbidden.
When it is set to Unlock, use of all keys is permitted.
Filtering/
Firewall,
SNMPv1/v2,
SNMPv3, SSL,
IPSec,
IEEE802.1x
An explanation about each security setting is displayed.
When you click a link in the sentence, the appropriate tab of
the Advanced page opens.
Item Description
Network Specifies whether or not to restrict access from each of the
interfaces on the left. Access from the interfaces that are set
to Block is restricted.
Access from the network interface cannot be restricted.
Access can be restricted on a per-protocol basis. Refer to the
next section.
USB Device
USB Host
Parallel I/F
Optional I/F
COMMAND CENTER Pages
14 KYOCERA COMMAND CENTER
Basic > Security > Device Security > Network Security
This allows you to enable communication with the printing system on a per-protocol
basis.
Basic > Security > User Login
When the authentication function is set on the Advanced > Management >
Authentication page (Local Authentication, depending on model), you must register
users and set access levels on this page.The available access levels are User and
Administrator.
One administrator account is registered by default.
Number of Users shows the number of the current users. By entering a user name in
Search by Name, you can search for the user.
Adding a New User Login
1. Click User Login, open the User Login page.
2. Click Add and enter the information of the user.
3. Click Submit.
Editing a User Login
1. Click User Login, open the User Login page.
2. Click the desired Login User Name or User Name to edit the user and modify their
information.
3. Click Submit.
Deleting a User Login
1. Click User Login, open the User Login page.
2. Check the desired user. When the check box on the left side of Login User Name is
selected, all users displayed on the page will be checked.
Item Description
SNMP v3,
NetWare,
AppleTalk,
NetBEUI, IPP,
IPP over SSL,
HTTP, HTTPS,
FTP
(Transmission),
FTP
(Reception),
SMB, SNMP,
SMTP, POP3,
Raw Port (Raw),
LPD, LDAP,
WSD Print,
WSD Scan
Specifies whether or not to restrict communication via each
of the protocols on the left.
The communication via the protocols that are set to Block is
restricted.
The settings made on this page affect the protocol settings
on the Advanced page.
COMMAND CENTER Pages
Operation Guide 15
3. Click Delete.
The User Login - Delete page appears. You can confirm the users to be deleted.
4. Click Delete when the desired users are selected.
Basic > Security > Certificates
This page allows you to create or update certificates or check details on certificates.
After you have changed this setting, you must restart this machine. For the restarting
procedure, refer to Basic > Defaults > Reset on page 9
Device Certificate - Self Issued
The self-issued certificate is automatically issued by default. The automatically issued
certificate has the country code, common name (in a form of "KMxxxxxx" as for model
names), and a validity period of about 10 years already configured.
Device Certificate - CA Issued
Item Description
Self Certificate Displays whether the certificate is active.
Expiration Displays the validity period of the certificate.
View Certificate Click View to view details on the certificate.
Create
Certificate
Click Create to create a certificate.
Edit Certificate Click Edit to update the validity period of the certificate.
Export
Certificate
Click Export to display the download dialog for the file. Click
Save to download the exported certificate.
If the printing system supports self-issued certificates only, it
cannot carry out encrypted communication via IPP over SSL
with Windows Vista/7 because the IPP over SSL function of
Windows Vista/7 does not deem self-issued certificates as
trusted. To enable printing via IPP over SSL, export the self-
issued certificate from the printing system and import it into
Windows Vista/7 as a trusted certificate. In this case, the
access name must match the common name of the
certificate.
Item Description
CA Certificate Displays whether the certificate issued by the Certification
Authority (CA) is active or not.
Expiration Displays the validity period of the certificate.
View Certificate Click View to view the details of the certificate.
Import
Certificate
Click Import to open the File Import window. Click Browse
to open the file selection dialog box. Select a file and click
Open. When the certificate is password-protected, enter the
password and click Submit. The certificate is imported.
COMMAND CENTER Pages
16 KYOCERA COMMAND CENTER
Root Certificate
Application Certificate
Printer Page
This section includes settings that apply to the printing function of the machine, such as
default print resolution or copy count.
Delete
Certificate
Click Delete. The certificate is displayed. Click Delete again
to delete the certificate.
When the CA issued certificate is deleted, the settings are
made invalid if Authentication Type is set to Certificates for
IPSec. The self Issued certificate is made valid for SSL.
Item Description
Root Certificate Displays whether the certificate is active.
Expiration Displays the validity period of the certificate.
View Certificate Click View to view details on the certificate.
Import
Certificate
Click Import to open the File Import window. Click Browse
to open the file selection dialog box. Select a file and click
Open. Click Submit to import the certificate.
Delete
Certificate
Click Delete. The certificate is displayed. Click Delete again
to delete the certificate.
When all root certificates are deleted, the settings are made
invalid if Authentication Type is set to Certificates for
IPSec. In addition, IEEE802.1x is turned Off.
Item Description
IEEE802.1x
Client
Certificate
Displays whether the certificate is active.
Expiration Displays the validity period of the certificate.
View Certificate Click View to view details on the certificate.
Import
Certificate
Click Import to open the File Import window. Click Browse
to open the file selection dialog box. Select a file and click
Open. Enter the password and click Submit. The certificate
is imported.
Delete
Certificate
Click Delete. The certificate is displayed. Click Delete again
to delete the certificate. When the certificate is deleted,
IEEE802.1x is turned Off.
Item Description
COMMAND CENTER Pages
Operation Guide 17
Default printer settings will be overridden by the printer driver settings. Settings that
affect the machine entirely, such as locking the operation panel, are found under Basic
Page on page 7.
Printer > Summary of Network Printer Access Methods
The following information that has already been set is displayed here.
- IP Address
-Host Name
- Net BEUI Name
- Apple Talk Name
Printer > System
The table below provides a summary of the items displayed on the System page.
Item Description
Form Feed
Timeout
Adjusts the timeout between 5 and 495 seconds, after which
a form feed will occur in the absence of data. The default
setting is 30 seconds.
Emulation Selects an emulation mode.
Alternate
Emulation
Specifies which emulation mode should be used for
processing at the time data other than KPDL is received,
when AUTO is selected for emulation.
JPEG/TIFF Print This determines the physical size of JPEG images when
printing them from a USB flash device. Choices include Fit
to Paper Size, Image Resolution, and Fit to Print
Resolution.
XPS Fit to Page This determines the page size for printing XPS data. Turn
On to fit print data over the page size; and turn Off to print in
the original size.
Paper Feed
Mode
Determines the behavior of paper feed selection when the
paper you requested of size and/or type is not available in
the current paper source. Auto lets the machine to search
for the matching paper including all the paper sources.
Fixed does not perform searching in the other paper
sources.
Duplex Mode *1 Selects the default duplex mode from Off, Long Edge and
Short Edge.
Copies Sets the number of copies to print.
Page Orientation
Switches Portrait or Landscape page orientation.
Tone *2 Sets Tone mode to Normal or Fine. The default setting is
Normal.
Gloss Mode *2*4 Sets Gloss Mode to High or Low. The default setting is
Low.
Color Mode *2 Sets Color Mode to Black & White (Monochrome) or Full
Color.
COMMAND CENTER Pages
18 KYOCERA COMMAND CENTER
*1 : Available on machines with the duplex printing.
*2 : Available for some color machines.
*3 : Available for some machines.
*4 : Available on machines which support Gloss Mode.
Printer > System > APL. Filter
This page allows you to configure the APL. Filter. The APL. Filter is a function that
converts the received print data to the specified code and prints that data.
Printer > System > APL. Filter Parameters
Configure items that can be set differently between APL. Filters. You can specify fonts
and the text to be converted.
Printer > Media Input
This page lets you configure paper trays by type and size. You can also configure
cassette groups.
KIR Mode *3 Switches KIR smoothing On or Off.
EcoPrint Mode
*3
Switches EcoPrint On or Off to control toner consumption
for saving the printing costs. The default setting is Off.
Resolution *3 Changes the printing resolution.
Item Description
Item Description
Filter Switches the APL. Filter On or Off.
Filter Name Selects the APL. Filter. You can select the ASCII to KPDL
conversion process.
Item Description
Font Specifies the fonts used for printing.
Start of String Specifies the character string with which the text to be
converted begins. Up to 15 single-byte characters can be
specified.
End of String Specifies the character string with which the text to be
converted ends. The default setting is \f. Up to 15 single-byte
characters can be specified.
Item Description
Default Determines the default tray to feed paper from.
Tray Displays the trays including those provided by option.
COMMAND CENTER Pages
Operation Guide 19
Printer > Document Output
This page lets you select an output tray.
Scanner Page
This section includes settings that apply to the scanning function of the machine, such
as default scan resolution or original placement.
In order to attach scanned data file to an E-mail and send it, the SMTP settings on the
Advanced page must be completed.
Scanner > Defaults
The table below provides a summary of the items displayed on the Scanner > Default
page.
Size Displays the paper size for each input tray. This setting can
be changed using the dropdown list.
Type Displays the paper type for each input tray. This setting can
be changed using the dropdown list.
Group Settings If multiple cassettes are available, you can set up to three
groups of cassettes. Cassettes in a group are treated as a
single tray. Paper can be fed continuously from the grouped
cassettes.
Item Description
Item Description
Paper Output Determines the default output tray.
Item Description
Color Selection
(Copy)
This selects color mode for copying. Auto automatically
identifies full color or black and white from the original
document to copy. You can manually select either Full Color
or Black & White to forcedly switch color mode.
Color Sel.
(Send/Store)
This selects color mode for scanning or storing. Auto Color
(Color/Grayscale) and Auto Color (Color/Black & White)
allow you identify color for the original document to scan.
You can manually select Full Color, Grayscale, or Black &
White to forcedly switch color mode, or if your printing
system supports only black and white.
Density This adjusts exposure (darkness) of scanning an original
document. Auto automatically provides an exposure best
suited for the original document. Manual invokes the
exposure which is adjusted manually in the machine.
Scan
Resolution
Specifies the resolution. The maximum resolution using full
color or gray scale mode is 300 x 300 dpi.
To scan in full color or gray scale with 400 dpi or 600 dpi
resolution, expansion of the internal memory is required.
COMMAND CENTER Pages
20 KYOCERA COMMAND CENTER
Scanner > FTP
The table below provides a summary of the items displayed on the FTP page.
Scanner > SMB
The table below provides a summary of the items displayed on the SMB page.
Original Image The original quality is selected according to the type of
original.
Switches the original quality between Text, Text+Photo,
and Photo.
File Format
Selects the file format in which the scanned data will be saved.
Image Quality
PDF/TIFF/JPEG
Selects the file quality mode (
1 [Low]
to
5 [High]
) in which the
scanned data will be saved.
High-
Compression
PDF Image
Selects the compression rate for PDF files from 1 (Low), 2
(Medium), and 3 (High).
High-
Compression
PDF Auto Color
Sets whether to enable or disable the automatic color/
monochrome detection for the original to be scanned.
Auto Color
Correction
Selects the detection level from five levels applied when
High-Compression PDF Automatic Color Detection is set
to ON. The color mode tends to be used at Level 1 and the
monochrome mode at Level 5.
Zoom Switches the zoom ratio between Auto and 100%. The
default setting is 100%.
Original
Orientation
Switches between Top Edge Top and Top Edge Left.
Item Description
Item Description
FTP Switches FTP On or Off.
FTP Port Number
Set the FTP Port Number or use the FTP default port 21.
FTP Encrypted
TX
This enables or disables Encryption for communication.
When turned On, the encryption algorithm that is selected
by Advanced > Security > Secure Protocols on page 51 is
used.
Item Description
SMB Protocol Switches the SMB Protocol On or Off.
SMB Port
Number
Set the SMB default Port Number or use the SMB default
port 139 (For Windows Vista/7, use 445).
COMMAND CENTER Pages
Operation Guide 21
Scanner > E-mail
The table below provides a summary of the items displayed on the E-mail page.
Scanner > i-FAX
This sends scanned data in i-FAX mode. The subject and body contents for i-FAX must
be specified. The contents displayed on this page are the same as in Scanner > E-mail,
described above.
FAX / i-FAX Page
This section includes settings, such as FAX transmission and reception settings, that
apply to the FAX function of the device. For models that do not support i-FAX, FAX is
displayed on the menu.
FAX / i-FAX > Common > Defaults
The table below provides a summary of the items displayed on the FAX / i-FAX >
Common page.
FAX / i-FAX > Common > Transmit
The table below provides a summary of the items displayed on the Transmit page.
Item Description
Subject You can include the model name of the printer, serial
number, MAC address, host name and IP address in the
subject line as follows: Enter one of the following conversion
strings starting with %. The string will be converted into a
pre-defined string to display the above information.
- %printer = Model
- %serial = Serial Number
- %etheraddr = MAC Address
- %host = Host Name
- %ip = IP Address
Body You can enter the information that you want to appear in the
body of the E-mail.
Item Description
Local FAX Name
Specifies your FAX system name.
Item Description
TTI Selects On or Off whether to send the TTI (Transmit
Terminal Identifier) information to other party.
TTI Position Selects the position of the TTI to be printed on the
transmitted documents.
COMMAND CENTER Pages
22 KYOCERA COMMAND CENTER
FAX / i-FAX > Common > Receive
The table below provides a summary of the items displayed on the Receive page.
FAX / i-FAX > Common RX/Forward Requirements > General
Conditional reception/forwarding is a function for automatically forwarding documents
received by FAX or i-FAX to other FAX machines, sending them as attachments to E-mail,
or saving them into a FAX box instead of printing if they satisfy the specified conditions.
For example, you can forward faxes from particular customers received during business
hours to the E-mail addresses of the people responsible for those customers, print and
save them in a FAX box if they are received outside business hours, and forward faxes
from outside of your business area to the business office nearest to the sender's fax
number.
For models that do not support RX/Forward Requirements, the documents received
are forwarded in the same requirement.
Item Description
FAX Media Type Sets the media type for printing the received documents.
Refer to Paper Specifications.
Use MP Tray Selects whether or not to include the MP (multi purpose) tray
for auto media selection when printing received documents.
When turned On, the MP tray will be included as an option
for auto media selection, and when turned Off, only the
cassettes will be selected.
Reduced RX
Size
Specifies the printing configuration for printing a document,
which is larger than the selected paper size. When Same
Size Override is selected, the document will be printed on
multiple sheets of paper without reducing the text. When
Reduction Override is selected, the document will be
printed on one sheet whenever possible.
Receive Date/
Time
Selects On or Off whether to print the reception information
such as the received date, the received time, the transmitting
party's information and the number of transmitted pages on
the top of the received documents.
Duplex Printing Specifies whether or not to use the Duplex mode.
2in1 Receive Enables or disables 2in1 reception.
Receive Bulk
Print
Enables or disables FAX bulk reception. When enabled, the
FAX system prints the received documents after its reception
completes. It will be possible to make copies during that
reception.
COMMAND CENTER Pages
Operation Guide 23
Types of RX/Forward Requirements
Open the FAX/i-FAX > Common > RX/Forward Requirements > General page.
Select one of the following items.
Settings for Forwarding Processes Using a Requirement List
Open the FAX/i-FAX > Common > RX/Forward Requirements > Requirement List
page.
1. Add the new condition to the Requirement List. Click Add.
2. The Requirement List - Add page appears. Specify the condition for the FAX
forwarding process.
Item Description
Off Disables the forwarding process. Received faxes are
printed on paper as in normal operation.
Use Requirements List Executes the forwarding process according to the
specified conditions. For the setting procedure, refer
to Settings for Forwarding Processes Using a
Requirement List on page 23.
All Executes the forwarding process without specifying
conditions. All received faxes are processed in the
same way. However, the process of saving them in a
FAX box cannot be selected. Clicking Advanced
invokes a behaviour equal to specifying all
conditions.For the setting procedure, refer to Settings
for Applying the Same Forwarding Process without
Using a Requirement List on page 26.
Item Description
Requirement Number Enter a number that identifies the condition set.
Name Give the condition set here an easily recognizable
name.
Status Specify whether to enable or disable the condition.
This item is set to Off for the condition that has just
been added. To set this item to On, set the conditions
and then click to select the desired condition on the
Requirement List and change the setting.
If the requirement sets include the same Activating
Time Setting, Activating Time and Sub Address
settings, these requirement sets will not be enabled
at the same time.
Activating Time Specify a period of hours during which the forwarding
process is executed. Select Time Specification to
forward only faxes received during a particular period
of hours or All Day not to specify the hours.
Enable Time When Time Specification is selected in the previous
item, specify the start time and end time.
COMMAND CENTER Pages
24 KYOCERA COMMAND CENTER
3. After you have finished setting all items, click Submit.
4. The Requirement List page appears. Check that the condition you have set is added
to the Requirement List.
Click the name of the condition under which you want to execute the forwarding process.
The Detail/Edit page opens. Set Status to On.
5. Then, specify how the forwarding process is executed. Click the desired items among
the following three Action Settings items in the lower part of the same page. When you
want to execute multiple forwarding processes at the same time, for example printing
and saving in a FAX box, click both items and set the processes.
File Name
Specify the file name to be used for the forwarded file.
Additional Information Specify the information to be added to the file name
specified in the previous item.
Add Sender
Information
Determine whether the sender information are added
to the file name or not.
Priority Prioritize the search keys when conducting searching
over the sending criterions.
Requirement Type Select the condition type from the following items.
- FAX Sub Address
-FAX Number
- FAX Reception Port
- i-FAX Address
When an item is selected, the text box below it accepts
entry of the necessary information on the selected
item. Enter the condition necessary for each item.
Asterisks (*) can be used as wildcards. For example,
to specify all faxes that came from Tokyo, select
FAX
Number
and enter "03*" in the FAX number text box.
For some models which shows
Search by
when
FAX
Number
or
i-FAX Address
is selected, you can use a
search criteria such as
Same as
or
Start with
, etc.
Wildcards cannot be used for these models.
When the search criteria is Same as, up to 9 are
forwarded to the FAX Box.
FAX Reception Port
shows the list in which you can
select
Port 1
or
Port 2
.
If you selected FAX Sub Address for Requirement
Type, enter a subaddress subsequently.
Item Description
Print Prints received documents on paper.
Name Displays the condition name.
Status Displays whether the condition is currently used.
Print Specifies whether to print on paper.
Item Description
COMMAND CENTER Pages
Operation Guide 25
6. After you have finished setting all items, click Submit.
7. The screen returns to the Detail/Edit page.
After you have finished setting all items, click Submit.
Copies When the previous item is set to On, specify the
number of copies.
Forward
Forwards received documents to other FAX machines,
E-mail addresses, shared folders, and so on.
Name Displays the condition name.
Status Displays whether the condition is currently used.
Forwarding Turn On to enable forwarding.
File Format Selects the format of forwarded files from PDF or
TIFF.(This item has effect when the forwarding
destination is E-mail, SMB, or FTP.)
FTP Encrypted
TX
Turn On to enable encryption for transmission. Note
the SSL protocol must also be turned on. Refer to
Advanced > Security > Secure Protocols on page 51.
Subject
Additional
Information
When a forwarding address is specified as
destination, Sender Name or Sender FAX No./
Address is appended at forwarding. When None,
these will not be appended.
Page Separate Specifies whether to split the fax into files as many as
the number of pages. Select On to split the fax.(This
item has effect when the forwarding destination is E-
mail, SMB, or FTP.)
Number of
Destination
Displays the number of registered destinations
displayed for the next item.
Destination List Displays a list of registered forwarding destinations.
Faxes are forwarded to all destinations displayed
here. For how to add a destination, refer to Setting
Destinations on page 26.
Save to FAX Box Saves received documents in a FAX box.
Name Displays the condition name.
Status Displays whether the condition is currently used.
Save to FAX Box
Specifies whether to save faxes in a FAX box. This is
not stored in the FAX box if the forwarding conditions
do not meet.
Box Name Specifies the FAX box to be used. When the selection
button is clicked, a list of registered FAX boxes
appears. The FAX box to be specified here must be
registered in advance. For how to add a FAX box,
refer to Document Box > FAX Box on page 34.
Item Description
COMMAND CENTER Pages
26 KYOCERA COMMAND CENTER
8. The Requirement List page appears. Check that the status of the condition you have
set is On.
Repeat the above steps to set more conditions.
9. Finally, set the process for faxes that do not satisfy any of the conditions on the
Requirement List.
Click Advanced of Not complying with the requirements.
10. The Requirement List - Advanced page appears.
Set whether to execute forwarding processes for faxes satisfying no conditions by
setting the status to On or Off. When this item is set to On, set the subsequent items.
The procedure is almost the same as the procedure for adding a condition. See steps 2
to 6 as a reference.
11. After you have finished setting the items, click Submit.
This completes the settings for forwarding processes using a Requirement List.
Settings for Applying the Same Forwarding Process without Using a
Requirement List
Open the FAX/i-FAX > Common > RX/Forward Requirements > General page.
1. Click Advanced in RX/Forward Requirements.
2. The RX/Forward Requirements - Advanced page appears. Specify the forwarding
process. The procedure is almost the same as the procedure for adding a condition. See
steps 2 to 6 as a reference.
NOTE: The process of saving faxes in a FAX box cannot be selected as the
forwarding process to be applied without using a Requirement List.
3. After you have finished setting the items, click Submit.
4. Returns to the RX/Forward Requirements page.
Select ALL and click Submit.
This completes the settings for applying the same forwarding process without using a
Requirement list.
Setting Destinations
When setting Forwarding in Action Settings described above, you have to register
Destination in advance. You can add a new destination or an address registered in the
address book to Destination.
Addition
Open the Action Settings > Forward page.
1. Click Add.
2. Select the desired type of forwarding process from Address Type. The available types
are as follows:
Item Description
E-mail Forwards faxes by E-mail. Specify E-mail address.
COMMAND CENTER Pages
Operation Guide 27
3. After you have finished specifying the destination, click Submit.
The Action Settings > Forward page appears. Check that the Destination is added to
the Destination List.
Addition from the Address Book
There are two types of address book: address book contacts and address book groups.
In address book contacts, each entry has an address of one person. In address book
groups, each entry has multiple addresses. When an address of a group is added, faxes
are forwarded to all addresses registered in the group.
Before adding an address from an address book, you have to register the address in the
address book. For how to register an address in an address book, refer to Basic >
Defaults > Address Book > Contacts on page 10 or Basic > Defaults > Address Book >
Groups on page 11.
Open the Action Settings > Forward page.
1. Click Import Contacts or Import Groups.
2. The address book opens. Put a check mark in the check box for the address or group
you want to add to the destinations.
3. After you have finished selection, click Submit.
4. The Action Settings > Forward page appears. Check that the Destination is added to
the Destination List.
Deletion
You can delete a Destination from the Destination List.
Open the Action Settings > Forward page.
1. Put a check mark in the check box for the destination you want to delete from the
Destination List.
2. After you have finished selection, click Delete.
The Action Settings > Forward - Delete page appears. You can confirm the
destinations to be deleted.
3. Click Delete when the desired destinations are selected.
SMB Saves faxes in a shared folder accessible from Microsoft
Windows Network. Specify Host Name, Port Number, Path
to the shared folder, Login User Name, and Login
Password.
FTP Saves faxes on an accessible FTP server. Specify Host
Name, Port Number, Path to the folder, Login User Name,
and Login Password.
FAX
Forwards faxes to other FAX machines. Specify
FAX Number
,
Transmit Start Speed
, and other necessary information on
the forwarding destinations.
i-FAX Forwards faxes to other i-FAX systems. Specify i-FAX
Address, Connection Mode, and other necessary
information on the forwarding destinations.
Item Description
COMMAND CENTER Pages
28 KYOCERA COMMAND CENTER
4. The Action Settings > Forward page appears. Check that the Destination is deleted
from the Destination List.
After confirming the settings, click Submit.
FAX / i-FAX > FAX > Defaults
The table below provides a summary of the items displayed on the
FAX / i-FAX > FAX >
Defaults
page.
FAX / i-FAX > FAX > Receive
The table below provides a summary of the items displayed on the Receive page.
Item Description
Local FAX
Number (Port 1/
2)
Specifies your FAX system number.
FAX Line Sets the type of phone line to correspond to the type of
telephone service that you are using. Be sure that the type of
phone line you select is correct because, if the setting is
incorrect, dialing will be impossible. The choices are Tone
(DTMF) or Pulse (10pps), or Pulse (20pps).
Local FAX ID Specifies your FAX system ID.
Speaker
Volume
Sets the volume of the internal speaker that allows you to
listen to conditions on the telephone line when the [On-
Hook] key was pressed. The choices are Off and levels 1, 2
or 3.
Monitor Volume Sets the volume of the internal speaker that allows you to
listen to conditions on the telephone line when the [On-
Hook] key was not pressed. The choices are Off and levels
1, 2 or 3.
Item Description
FAX Receive Selects the FAX reception mode. The selectable option is
different depending on the destination. The choices are Auto
(Normal, FAX/TEL, TAD or DRD) or Manual.
DRD Pattern Selects the DRD pattern. This menu is available only for
specific destinations.
This is not displayed on European models.
Remote
Switching Dial
Number
Specifies the remote switching dial number. You can specify
it within a range of 00 to 99. Remote switching allows you to
initiate FAX reception from a telephone connected to the
FAX system.
Encryption Key
No.
Sets the encryption key number to be used for encrypted
communication.
Reception Port Sets the receive-only port. (Available in multiport mode).
COMMAND CENTER Pages
Operation Guide 29
FAX / i-FAX > FAX > FAX Restrictions > General
The table below provides a summary of the items displayed on the FAX Restrictions >
General page.
FAX / i-FAX > FAX > FAX Restrictions > Permit Number List
The table below provides a summary of the items displayed on the Permit Number List
page.
FAX / i-FAX > FAX > FAX Restrictions > Permit ID List
The table below provides a summary of the items displayed on the Permit ID List page.
Number of Rings
(Normal)
Specifies the number of rings for Auto FAX reception
(Normal). You can specify it within a range of 1 to 15.
Number of Rings
(TAD)
Specifies the number of rings for Auto FAX reception (TAD).
You can specify it within a range of 1 to 15.
Number of Rings
(FAX/TEL)
Specifies the number of rings for Auto FAX reception (FAX/
TEL). You can specify it within a range of 0 to 15.
This is not displayed on European models.
Item Description
Item Description
Transmit
Restriction
Selects the transmitting restriction between Off and Use
Permit List + Address Book.
Receive
Restriction
Selects the receiving restriction between Off, Use Permit
List + Address Book, and Use Reject List.
Unknown
Number
Reception
Displayed when Use Reject List is selected in Receive
Restriction. This determines the behavior when the
machine has received a FAX with an unknown FAX number.
Select Permit to permit reception of unknown numbered
FAXes and select Reject to reject unknown numbered
FAXes.
Item Description
Add Clicking Add will display the Permit Number List - Add
page. Enter in Permit FAX Number the FAX number to add,
then click Submit.
Delete To delete a FAX number from Permit Number List, click the
checkbox next to the FAX number, then click Delete. If you
accept the confirming prompt, click Delete.
Item Description
Add Clicking Add will display the Permit ID List - Add page.
Enter in Permit FAX ID the FAX ID to add, then click
Submit.
COMMAND CENTER Pages
30 KYOCERA COMMAND CENTER
FAX / i-FAX > FAX > FAX Restrictions > Reject Number List
The table below provides a summary of the items displayed on the Reject Number List
page.
FAX / i-FAX > FAX > Encryption Key
Specifies the encryption key in hexadecimal. The length of the encryption key is 16
digits. Enter 16 characters using the numbers 0-9 and the letters A-F.
FAX / i-FAX > i-FAX > Defaults
The table below provides a summary of the item displayed on the Defaults page.
FAX / i-FAX > i-FAX > SMTP
The table below provides a summary of the items displayed on the SMTP page.
Delete To delete a FAX ID from Permit Number List, click the
checkbox next to the FAX ID, then click Delete. If you accept
the confirming prompt, click Delete.
Item Description
Item Description
Add Clicking Add will display the Reject Number List - Add
page. Enter in Reject FAX Number the FAX number to
reject, then click Submit.
Delete To delete a FAX number from Reject Number List, click the
checkbox next to the FAX ID, then click Delete. If you accept
the confirming prompt, click Delete.
Item Description
i-FAX Enables or disables i-FAX. Set to On to enable.
Item Description
SMTP Port
Number
Set the SMTP Port Number or use the SMTP default port 25.
SMTP Server
Name
Enter the SMTP server name or its IP address. If entering the
name, rather than the IP address, a DNS server address
must also be configured. The DNS server address may be
entered on the TCP/IP General page (refer to Advanced >
Protocols > TCP/IP > General on page 37).
SMTP Server
Timeout
Sets the timeout in seconds during which this machine tries
to connect to the SMTP server.
Authentication
Protocol
Enables or disables the SMTP authentication protocol or
sets POP before SMTP as the protocol. The SMTP
authentication supports Microsoft Exchange 2000.
COMMAND CENTER Pages
Operation Guide 31
FAX / i-FAX > i-FAX > POP3
The table below provides a summary of the items displayed on the POP3 page.
Authenticate as
Selects the user to be authenticated in SMTP authentication. If
you want to select a user other than i-FAX users, select
Other
and enter the
Login User Name
and
Login Password
for
authentication.
Login User
Name
When Other is selected for Authenticate as, the account
name set here will be used for SMTP authentication.
Login Password
Enter the login password.
POP before
SMTP Timeout
Enter the timeout in seconds during which this machine tries
to connect to the SMTP server when set POP before SMTP
as the Authentication Protocol.
Test Tests to confirm that the settings on this page are correct.
When the Test button is pressed, this machine tries to
connect to the SMTP server.
E-mail Size
Limit
Enter the maximum size of E-mail that can be sent in
Kilobytes. When the value is 0, the
limitation for E-mail size
is disabled.
Sender Address Displays the sender address used for E-mails sent from this
machine. For how to change the sender address, Set the E-
mail address in E-mail Address on FAX / i-FAX > i-FAX >
POP3 on page 31.
Signature Displays the signature to be inserted in the end of the E-mail
body. For how to change the signature, refer to Advanced >
E-mail > SMTP > General on page 42.
Item Description
Item Description
Check Interval Displays the interval, in minutes, for connecting to the POP3
server to check for incoming mails. For how to change this
setting, refer to Advanced > E-mail > POP3 > General on
page 44.
Run once now Click the Receive button to immediately receive E-mail from
the POP3 server.
E-mail Address Enter the E-mail address for i-FAX. The E-mail address is
displayed in Sender Address on FAX / i-FAX > i-FAX >
SMTP on page 30.
POP3 Server
Name
Enter the POP3 server name or IP address.
POP3 Port
Number
Enter the POP3 port number or use the default port number
110.
POP3 Server
Timeout
Enter the timeout in seconds during which this machine tries
to connect to the POP3 server.
COMMAND CENTER Pages
32 KYOCERA COMMAND CENTER
FAX / i-FAX > i-FAX > Domain Restrictions > General
The table below provides a summary of the items displayed on the Domain
Restrictions page.
FAX / i-FAX > i-FAX > Domain Restrictions > SMTP Restriction List
The table below provides a summary of the items displayed on the SMTP Restriction
List page.
FAX / i-FAX > i-FAX > Domain Restrictions > POP3 Restriction List
The table below provides a summary of the items displayed on the POP3 Restriction
List page.
Login User Name
Enter the login name of the user.
Login Password
Enter the password for connecting to the user name above.
Use APOP Enables or disables APOP.
Test Tests to confirm that the settings on this page are correct.
When the Test button is pressed, this machine tries to
connect to the POP3 server.
E-mail Size Limit
Enter maximum E-mail size in Kilobytes. When the value is
0, the limitation for E-mail size is disabled.
Cover Page Specifies whether to print the body of E-mail in addition to
the attached files.
When this item is set to On, the attached files and the body
of E-mail are printed.
When no attached files exist, only the body of E-mail is printed.
When this item is set to
Off
, only the attached files are printed.
When no attached files exist, nothing is printed.
Item Description
Item Description
SMTP Restriction
Selects the restriction level from Off, Reject, and Permit.
POP3 Restriction
Selects the restriction level from Off, Reject, and Permit.
Item Description
Domain Name Enter the domain names that can be permitted or rejected.
You can also specify the E-mail addresses.
Item Description
Domain Name Enter the domain names that can be permitted or rejected.
You can also specify the E-mail addresses.
COMMAND CENTER Pages
Operation Guide 33
Jobs Page
This section includes information on all device jobs including job status, scheduled job
and job log.
The table below provides a summary of the pages in Jobs page. When clicking the job
on each page, the detailed information of the job is displayed.
Document Box Page
This section includes addition and deletion of a document box, and deletion of
documents in a document box.
There are three types of document boxes: Custom Box, FAX Box (or Sub Address
Box), and Polling Box.
Document Box > Custom Box
The table below provides a summary of the items displayed on the Custom Box page.
Page Description
Status >
Printing Jobs
Status
Shows the job status for each operation. To show the latest
status, click Refresh. To cancel execution of the selected
job, click Job Cancel.
Status >
Sending Jobs
Status
Status > Storing
Jobs Status
Schedule Shows the scheduled job such as FAX delayed transmission.
To show the latest status, click Refresh. To cancel execution
of the selected job, click Job Cancel.
Log > Printing
Jobs Log
Shows the job log for each operation. To show the latest
status, click Refresh.
Log > Sending
Jobs Log
Log > Storing
Jobs Log
Item Description
Number of
Custom Boxes
Displays the number of registered custom boxes.
Add Displays a screen where you can add a new custom box.
Enter the required information and click the Submit button.
Delete Deletes the selected custom box.
COMMAND CENTER Pages
34 KYOCERA COMMAND CENTER
You can add, edit or delete a custom box as follows:
Adding a New Custom Box
1. Open the Custom Box page.
2. Click Add and enter information for the custom box.
3. Click Submit.
Editing a Custom Box
1. Open the Custom Box page.
2. Click the Box Number of the custom box to edit.
3. Click Detail/Edit and enter information for the custom box.
4. Click Submit.
Deleting a Custom Box
1. Open the Custom Box page.
2. Check the custom box to delete.
3. Click Delete. Enter the password, if required, and click OK. The Custom Box - Delete
page appears. You can confirm the user boxes to be deleted.
4. Click Delete when the desired custom box is selected.
Document Box > FAX Box
The table below provides a summary of the items displayed on the FAX Box page.
You can add, edit or delete a FAX box as follows:
Adding a New FAX Box
1. Open the FAX Box page.
2. Click Add and enter information for the FAX box.
3. Click Submit.
Editing a FAX Box
1. Open the FAX Box page.
2. Click the Box Number of the FAX box to edit.
Item Description
Number of FAX
Boxes
Displays the number of registered FAX boxes.
Add Displays a screen where you can add a new FAX box. Enter
the required information and click the Submit button.
Delete Deletes the selected FAX box.
COMMAND CENTER Pages
Operation Guide 35
3. Click Detail/Edit and enter information for the FAX box.
4. Click Submit.
Deleting a FAX Box
1. Open the FAX Box page.
2. Check the FAX box to delete.
3. Click Delete. Enter the password, if required, and click OK. The FAX Box - Delete page
appears. You can confirm the FAX boxes to be deleted.
4. Click Delete when the desired FAX boxes are selected.
Document Box > Sub Address Box
The table below provides a summary of the items displayed on the Sub Address Box
page.
You can add, edit or delete a Sub Address box as follows:
Adding a New Sub Address Box
1. Open the Sub Address Box page.
2. Click Add and enter information for the Sub Address box.
3. Click Submit.
Editing a Sub Address Box
1. Open the Sub Address Box page.
2. Click the Box Number of the Sub Address box to edit.
3. Click Detail/Edit and enter information for the Sub Address box.
4. Click Submit.
Deleting a Sub Address Box
1. Open the Sub Address Box page.
2. Check the Sub Address box to delete.
3. Click Delete.
The Sub Address Box - Delete page appears. You can confirm the Sub Address boxes
to be deleted.
Item Description
Number of Sub
Address Boxes
Displays the number of registered Sub Address boxes.
Add Displays a screen where you can add a new Sub Address
box. Enter the required information and click the Submit
button.
Delete Deletes the selected Sub Address box.
COMMAND CENTER Pages
36 KYOCERA COMMAND CENTER
Click Delete when the desired Sub Address boxes are selected.
Document Box > Polling Box
The table below provides a summary of the items displayed on the Polling Box page.
Setting a Poling Box
1. Open the Poling Box page.
2. Click Detail/Edit to delete or retain the document sent.
3. Click Submit.
Removing a document from the Poling Box
1. Open the Poling Box page.
2. Check the document to delete. When the check box on the left side of document is
selected, all documents displayed on the page will be checked.
3. Click Delete. The Poling Box - Delete page appears. You can confirm the documents
to be deleted.
4. Click Delete when the desired documents are selected.
Advanced Page
This section includes advanced settings that apply to the machine and is comprised
primarily of advanced network settings.
Always restart this machine after you have completed these settings in order to properly
register the content of those settings in the machine. Refer to Basic > Defaults > Reset
on page 9.
Advanced > Network Protocol Quick Summary/Secure Protocol Quick
Summary
The usage of the protocols that have already been set is displayed. The following
protocols can be displayed.
-TCP/IP
-Netware
-IPP
- AppleTalk
- NetBEUI
-SMTP
Item Description
Number of
Documents
Displays the number of registered documents.
Delete Deletes the checked documents.
Detail/Edit Determine, after the document has been sent, whether you
want the document to be automatically deleted or to be
retained (overwritten).
COMMAND CENTER Pages
Operation Guide 37
-POP3
- SNMP v1/v2
-SNMPv3
-LDAP
- SSL
- IPSec
- IEEE802.1x
Advanced > Protocols > TCP/IP > General
The table below provides a summary of the items displayed on the
TCP/IP > General
page.
Item Description
Host Name
Specifies a name for the printing system network component.
This name is also used as the NetBEUI printer name.
IPv4 Settings
DHCP/
BOOTP
Specifies whether or not to automatically obtain an IP
address using DHCP or BOOTP.
Auto-IP Turn On to automatically assign a unique IP address even
though a DHCP server does not exist or DHCP setting is Off
in the printing system. The range of the IP address to be
assigned is from 169.254.0.0 to 169.254.255.255, which is
reserved for Auto-IP. If an IP address is already assigned by
a DHCP server, this does not resolve a new IP address.
IP
Address
Assigns an IPv4 address to the printing system network
component. The format of the IPv4 address is a sequence of
numbers (32-bit in total) separated by dots, e.g.
192.168.110.171.
Subnet
Mask
Specifies the subnet mask.
Default
Gateway
Specifies the IP address of the default gateway.
Domain
Name
Specifies the DNS (Domain Name System) name of the
domain to which the printing system belongs. It should not
contain the host printer name, as in kyoceramita.co.jp.
DNS
Server
(Primary,
Secondary)
Specifies the IP addresses of the primary and secondary
DNS (Domain Name System) servers. When DHCP/BOOTP
is turned On, you can select to use either the DNS servers
obtained via DHCP or the DNS servers being set under this
item.
WINS
Server
(Primary,
Secondary)
Specifies the IP addresses of the primary and secondary
WINS (Windows Internet Name Service) servers. When
DHCP/BOOTP is turned On, you can select to use either the
WINS server obtained via DHCP or the WINS server being
set under this item.
COMMAND CENTER Pages
38 KYOCERA COMMAND CENTER
Advanced > Protocols > TCP/IP > IP Filters
This page allows you to configure IP filters. IP filters restrict access to the printing
system based on the IP addresses and protocols.
Specify the IP addresses or network addresses of the hosts to which access is granted.
Bonjour Specifies whether or not to automatically obtain an IP
address using Bonjour.
You can add a Bonjour printer from the Print Center of Mac
OS X. When using a Windows operating system, you can
use the Bonjour Printer Wizard to add a printer.
The following conditions must be satisfied to automatically
obtain an IP address using Bonjour: If DHCP/BOOTP is
turned Off, an IP address should not be specified. If DHCP/
BOOTP is turned On, automatic IP address assignment by
the DHCP server should not be enabled.
To allow printing from the Mac OS X system, the printer
needs to support KPDL.
Bonjour
Name
If Bonjour is turned On, this specifies the Bonjour name to
be used.
IPv6 Settings
IPv6
Specifies whether or not to enable the IPv6 protocol.
Select On to use the IPv6 protocol.
IP Address
Assigns an IPv6 address to the printing system network
component.
The format of the IPv6 address is a sequence of numbers
(128 bit in total) separated by colons, e.g.
2001:db8:3c4d:15::1a2c:1a1f.
Prefix
Length
Specifies the IPv6 prefix length. It can be a decimal value
between 0 and 128.
RA
(Stateless)
Select On to use RA instead of the DHCP server to
configure IPv6 addresses.
Default
Gateway
Specifies the IPv6 address of the default gateway.
DHCPv6
(Stateful)
Specifies whether or not to obtain IPv6 IP addresses by
automatic configuration. When RA is turned On, the IP
addresses and server information are obtained via DHCPv6
based on the settings of the automatic configuration made
under RA (router setting).
Domain
Name
Specifies the DNS (Domain Name System) name of the
domain to which the printing system belongs.
DNS
Servers
(Primary,
Secondary)
Specifies the IP addresses of the primary and secondary
DNS (Domain Name System) servers. When DHCPv6
(Stateful) is turned On, you can select to use either the DNS
servers obtained via DHCP or the DNS servers being set
under this item.
Item Description
COMMAND CENTER Pages
Operation Guide 39
If nothing is specified on this page, access from all hosts is allowed.
Advanced > Protocols > TCP/IP > Logical Printers
This page allows you to configure the Logical Printers. This machine can be used as a
virtual printer for converting ASCII print data to PostScript data or for adding and/or
replacing a character strings (commands) at the beginning or end of job data. Up to four
logical printers can be set.
Item Description
IP Filter (IPv4)
IP Address
(IPv4)
Specifies the IP address or network address to be permitted.
The number of specifiable entries differs depending on
models.
Subnet
Mask
Specifies the subnet mask to be permitted.
To permit access from all hosts on network 192, enter
"192.0.0.0" for the IP address and "255.0.0.0" for the subnet
mask.
Subnet mask can be left blank.
Protocols Specifies the protocol to be permitted. The following
protocols can be selected.
-LPD
-FTP
-IPP
-HTTP
-RAW Port
-SNMP
- IPP over SSL
-HTTPS
IP Filters (IPv6)
IP Address
(IPv6)
Specifies the IP addresses to which access is granted. The
number of addresses that can be specified varies depending
on the model used.
Prefix
Length
Specifies the IPv6 prefix length. It can be a decimal value
between 0 and 128.
Protocols Specifies the protocols through which access is granted.The
following protocols can be selected.
-LPD
-FTP
-IPP
-HTTP
-RAW Port
-SNMP
- IPP over SSL
-HTTPS
COMMAND CENTER Pages
40 KYOCERA COMMAND CENTER
Each logical printer can be used with either the FTP, LPR, IPP, NetBEUI, or Raw Port
protocol. All printout to a non-existent port will be accomplished to Logical Printer1.
Advanced > Protocols > Netware
This printing system supports both NDS and bindery printing in either print server mode
or remote printer mode.
NetWare setup requires installation of the following client software and login with
Administrator Privileges. If you are unsure, please contact your network administrator.
With Novell Client, creation of the NetWare print objects with the AdminManager
NetWare Setup Wizard requires the NetWare Client from Novell. For NetWare printing,
you may use the NetWare Client from either Novell or Microsoft.
For Admin Privileges, network operations (creating queues etc.) require 'admin' or
'supervisor' privileges (or equivalent). Certain portions of AdminManager may be
inoperable if you attempt those operations without sufficient privileges.
Item Description
TCP/IP Port
Number
Specifies the port number for the logical printer as well as
the TCP raw port number (9100, etc.). Conversion is applied
to data that is input to the specified raw port in accordance
with the selected logical printer. This port is invalid if it is
given a port number that is the same as that of an already
specified port (e.g. FTP or LPD).
Bi-directional
Printing
On or Off Bi-directional Printing using the TCP/IP raw port.
With this setting Off, all send data are discarded.
In order to have the data that is received from the printer
returned to the client when printing with PostScript, PJL and
other such commands, it is necessary to On bi-directional
printing.
Start of Job
String
Specifies the character string sent to the printer before
output directly to the output port (lp port). Specifies the
character string if it is necessary to transmit the control code
before printing.
End of Job
String
Specifies the character string sent to the printer after directly
outputting to the output port (lp port). Specify a character
string, if it is necessary, to send a control code after printing.
Item Description
NetWare
Protocol
Enables or disables the Network Protocol.
Bindery Mode Enables or disables Bindery Mode.
Frame Type Sets the Frame type. You can choose from Auto, 802.3,
Ethernet-II, SNAP or 802.2.
File Server
(Primary)
Enter the name of the primary File Server.
NDS Tree Enter the name of the NDS Tree.
COMMAND CENTER Pages
Operation Guide 41
Advanced > Protocols > IPP
Using IPP (Internet Printing Protocol) or IPP over SSL, you can output to the printing
system over the Internet or an intranet.
Advanced > Protocols > AppleTalk
You can print from Macintosh computers using the AppleTalk protocol.
The printing system network component supports Mac OS of various versions (System
Requirements on page 1) and is compatible with LaserWriter driver version 8.x.
NDS Context Enter the NDS Context.
Print Server
Mode
Enables or disables Print Server Mode.
Print Server
Name
Enter the Print Server Name.
Queue Polling
Interval
Enter the Queue Polling Interval in seconds.
Password
(optional)
Enter the Password, if required. Login to NetWare will be
successful only if the password set here matches the Print
Server password set within the NetWare utilities.
Remote Printer
Mode
Enables or disables Remote Printer Mode.
Print Server
Name
Enter the name of the printer server that the remote printer
belongs to.
Job Timeout Enter the timeout in seconds.
Item Description
Item Description
IPP Enables or disables IPP.
IPP Port
Number
Sets the port number to be used by IPP. In normal situations,
set this port number to 631, e.g.
http://(IP address):631/printers/lp1
IPP over SSL Enables or disables the IPP over SSL protocol. When this is
set to On, SSL in the secure protocol settings must also be
set to On. For details on secure protocol, see Advanced >
Security > Secure Protocols on page 51.
IPP over SSL
Port Number
Sets the port number to be used by IPP over SSL. In normal
situations, set this port number to 443, e.g.
https://(IP address):443/printers/lp1
COMMAND CENTER Pages
42 KYOCERA COMMAND CENTER
To set up the Ethernet interface to communicate via AppleTalk, enables AppleTalk
protocol operation on the printing system.
Advanced > Protocols > NetBEUI
Peer-to-peer printing is available using NetBEUI protocol. With this method, the printing
system is located in Windows Network Neighborhood.
Advanced > E-mail > SMTP > General
This machine can send Low Toner and other information via E-mail to the specified mail
address. To use the mail function, configure SMTP (Simple Mail Transfer Protocol) to
connect this machine to an E-mail server.
Item Description
AppleTalk Enables or disables AppleTalk protocol.
Printer Name Specifies the name of the printing system in the AppleTalk
network.
Zone Name Specifies the name of the AppleTalk zone (network). An
asterisk (*) means the default zone.
Item Description
NetBEUI
Protocol
Enables or disables NetBEUI protocol.
If NetBEUI is turned On, name resolution via NetBIOS
(NMB) can be used.
Printer Name Printer Name correlates with Host Name in the TCP/IP
General page (refer to Advanced > Protocols > TCP/IP >
General on page 37). If you want to change the NetBEUI
printer name, change the TCP/IP Host Name.
Workgroup Workgroup represents the workgroup which will appear in
Entire Network in Windows Network Neighborhood.
Comment You can enter comments here. (This can also be left blank.)
Item Description
SMTP Protocol Enables or disables SMTP protocol. To use E-mail, this
protocol must be enabled.
SMTP Port
Number
Set the SMTP Port Number or use the SMTP default port 25.
SMTP Server
Name
Enter the SMTP server name or its IP address. If entering the
name, rather than the IP address, a DNS server address
must also be configured. The DNS server address may be
entered on the TCP/IP General page (refer to Advanced >
Protocols > TCP/IP > General on page 37).
SMTP Server
Timeout
Sets the timeout in seconds during which this machine tries
to connect to the SMTP server.
COMMAND CENTER Pages
Operation Guide 43
Advanced > E-mail > SMTP > E-mail Recipient #
This page allows you to set the address for receiving E-mail and contents of event
reports. Up to three recipients can be set.
Authentication
Protocol
Enables or disables the SMTP authentication protocol or
sets POP before SMTP as the protocol. The SMTP
authentication supports Microsoft Exchange 2000.
Authenticate as Specifies the user to be authenticated in SMTP
authentication. When POP3 User 1 to 3 (refer to Advanced >
E-mail > POP3 > User # on page 45) and i-FAX User are
set, you can select one of them. If you want to select a
different user, select Other and enter the login account
name and login password for authentication.
Login User
Name
When Other is selected for Authenticate as, the account
name set here will be used for SMTP authentication.
Login
Password
When Other is selected for Authenticate as, the password
set here will be used for authentication.
POP before
SMTP Timeout
Enter the timeout in seconds during which this machine tries
to connect to the SMTP server when set POP before SMTP
as the Authentication Protocol.
Test Tests to confirm that the settings on this page are correct.
When the Test button is pressed, this machine tries to
connect to the POP3 server.
E-mail Size
Limit
Enter the maximum size of E-mail that can be sent in
Kilobytes. When the value is 0, the limitation for E-mail size
is disabled.
Sender Address Enter the E-mail address of the person responsible for the
printing system, such as the printer administrator, so that a
reply or non-delivery report will go to a person rather than to
the machine. The sender address must be entered correctly
for SMTP authentication. Note that no mail message can be
sent unless the sender's address is specified.
Signature Enter the signature. The signature is free form text that will
appear at the end of the E-mail body. It is often used for
further identification of the machine.
Domain
Restriction
Enter the domain names that can be permitted or rejected.
You can also specify the E-mail addresses.
Item Description
Item Description
Recipient #
Address
Enter the E-mail address for this recipient.
COMMAND CENTER Pages
44 KYOCERA COMMAND CENTER
Advanced > E-mail > POP3 > General
To use the E-mail function, you need to connect the printing system to an E-mail server
using the POP3 protocol.
Subject Specifies the information to be displayed at Subject. When
the following variable starting with "%" is entered, it is
converted to values for information set on this machine and
displayed at Subject.
- %printer = Model
- %serial = Serial Number
- %etheraddr = MAC Address
- %host = Host Name
- %ip = IP Address
Event Report
Items
Select the events you want to be reported. These events are:
- Add Paper
- Low Toner
- Add Toner
- Cover Open
- Paper Jam
- All Other Errors
Event Report
Interval
Enter the E-mail interval. An E-mail will be sent at the end of
the interval only when at least one of the selected error
conditions has occurred during the interval. The interval can
be set from 1 minute to 10000 minutes.
Scheduled
Report Items
Check one or more items from Printer Status, Network
Status, and Counter Status.
Scheduled
Report Interval
Select the time or interval for sending the status information.
•None: No report is sent.
•Monthly: Sends on the specified time of specified month.
•Weekly: Sends on the specified time of every week.
•Daily: Sends at the specified time of every day.
•Hourly: Sends at the specified interval every hour.
If a specified day does not exist in the month, such as the
31st, the last day of the month is used as the specified day.
Run once now You can test this by clicking the Send button to immediately
send a report.
Item Description
Item Description
POP3 Protocol Enables or disables POP3 protocol.
Check Interval Checks E-mails in POP3 server at specific interval. Specify
the interval in the range from 3 minutes to 60 minutes. The
default is 15 minutes.
Run once now Click the Receive button to immediately receive E-mail from
the POP3 server.
Domain
Restriction
Enter the domain names that can be permitted or rejected.
You can also specify the E-mail addresses.
COMMAND CENTER Pages
Operation Guide 45
Advanced > E-mail > POP3 > User #
This page allows you to set the POP3 user account and information on the POP3 server.
Up to three users can be set.
Advanced > Management > SNMP > SNMPv1/v2c
The SNMP protocol is used for providing and transferring management information
within the network environment. Should an error occur such as Add Paper, the printing
system automatically generates a trap, an error message sent to up to two pre-
determined trap recipients.
Item Description
User Profile # Enables or disables this user number.
E-mail Address Enter the E-mail address.
POP3 Server
Name
Enter the POP3 server name or IP address.
POP3 Port
Number
Enter the POP3 port number or use the default port number 110.
POP3 Server
Timeout
Enter the timeout in seconds during which this machine tries
to connect to the POP3 server.
Login User
Name
Enter the login name of the user.
Login
Password
Enter the password for connecting to the user name above.
Use APOP Enables or disables APOP.
Test This will test one transmission for each press.
Delete e-mail
after retrieval
Enables or disables the Delete E-mail after retrieval function.
E-mail size limit
Enter maximum E-mail size in Kilobytes. When the value is 0,
the limitation for E-mail size is disabled.
Cover Page Specifies whether to print the body of E-mail in addition to the
attached files.
When this item is set to On, the attached files and the body
of E-mail are printed.
When no attached files exist, only the body of E-mail is printed.
When this item is set to
Off
, only the attached files are printed.
When no attached files exist, nothing is printed.
Item Description
SNMPv1/v2c Sets whether to use the SNMPv1/v2c protocol. Set On to use
it.
COMMAND CENTER Pages
46 KYOCERA COMMAND CENTER
Advanced > Management > SNMP > SNMPv3
The table below provides a summary of the items displayed on the
SNMPv3
page
.
Read
Community
The read community can be used like a password. The
default read community name is public. When a
management application sends an SNMP request to read a
value, it must include the correct read community name or
the request will be rejected by the printing system.
Write
Community
Similar in function to the read community, but used in SNMP
requests to write (change) a value.The default write
community name is public.
sysContact The MIB-II sysContact object, usually the E-mail address of
the network administrator.
sysName The MIB-II sysName object, usually the host or domain name
of the printing system.
sysLocation The MIB-II sysLocation object, usually the location
information of the printing system.
HP Web
Jetadmin
Compatibility
Turns HP Web Jetadmin Compatibility On or Off.
Authentication
Traps
Specifies whether to use authentication traps. If enabled, an
SNMP trap is generated when an attempt to read or write is
made using an incorrect community name. The trap is sent to
the configured trap address.
Trap
Community
The SNMP trap community name to be used when the
printing system generates a trap.
Trap IP Address
(IPv4)
Enter the IPv4 address that receives traps. Select On to
enable trap receiving.
Trap IP Address
(IPv6)
Enter the IPv6 address that receives traps. Select On to
enable trap receiving.
Trap IPX Address
Enter the IPX address that receives traps. Select On to
enable trap receiving.
Selected Errors Select the events which will cause a trap to be generated
from Add Paper, Low Toner, Add Toner, Cover Open,
Paper Jam, and All Other Errors.
Item Description
Item Description
SNMPv3 Sets whether to use the SNMPv3 protocol. Set On to use it.
Authentication
Sets whether to authenticate the user in SNMP communication.
Hash Selects the hash algorithm. This item is displayed when the
Authentication is On.
COMMAND CENTER Pages
Operation Guide 47
Advanced > Management > LDAP
The printing system can refer to the address book which is on the LDAP server as an
external address book and assign a FAX number and E-mail address to the destination.
Privacy Sets whether to encrypt the communicated data in SNMP
communication. This becomes available when
Authentication is enabled.
Encryption Selects the encryption algorithm. This item is displayed when
Privacy is On.
User Name Enter the name of the read-only user.
Password Enter the password for the read-only user.
User Name Enter the name of the read/write user.
Password Enter the password the read/write user.
Item Description
Item Description
LDAP Enables or disables access to the LDAP server.
LDAP Server
Name
Specifies a name or IP address for the LDAP server.
LDAP Port
Number
Specifies a port number for LDAP or use the LDAP default
port 389.
Search Timeout Specifies a period of time for searching the LDAP server.
Login User
Name
Specifies the user name.
Login Password
Specifies the password.
Max Search
Results
Specifies a maximum number of displayed results which
have been searched on the LDAP address book.
Search Base
Specifies a base object which indicates the starting point in the
tree structure of the database for the LDAP directory searching.
Display Mode
Selects the default display mode from
Display from the first
name
and
Display from the family name
.
LDAP
Encryption
Selects the type of encryption according to the type of
security employed by the LDAP server. Select Off when
encryption is not used.
LDAPv3/
TLS
Uses explicit mode for data communication. Select this if the
server supports the startTLS command. This uses the same
port (389) as LDAP.
COMMAND CENTER Pages
48 KYOCERA COMMAND CENTER
Advanced > Management > Authentication > General
Setting Authentication allows only the predefined users to access pages. In addition,
you can discriminate users by giving either the General User or Administrator privilege
to each user. Before using the authentication function, you have to define those users.
For how to define users, refer to Basic > Security > User Login on page 14.
NOTE: If the server type is [Kerberos (Win2000/2003)], only domain names
entered in uppercase will be recognized.
When a user sets authentication and accesses COMMAND CENTER, only the Start
page is displayed. The Login button is displayed in the upper left of the screen. Click it
to log in. When the user logs in with an Administrator account, hidden pages are
displayed and can be accessed. When the user logs in with a General User account,
the user can access the user's account page on Basic > Security > User Login and the
LDAP
over SSL
Uses implicit mode for data communication. The server
provides services using the LDAP over SSL port (636).
Encryption is applied to any data communication using this
port.
Item Description
Item Description
Authenticate
mode
Specifies whether to enable or disable the authentication
function. To disable it, select Off. To enable it, select either of
the following.
Local
Authenti-
cation
Users are registered in this machine and one-to-one
authentication is performed between this machine and a PC.
Network
Authenti-
cation
This machine and relevant PCs need to be under the
management of the Windows domain network. Depending
on model, users registered in this machine must be the same
as those registered in the domain controller.
Domain Name Specifies the domain name of the Windows domain network
when Network Authentication is specified in the preceding
item.
Host Name Specifies the domain controller name of the Windows
domain network when Network Authentication is specified
in the preceding item.
Server Type Specifies the authentication method used by the domain
controller when Network Authentication is specified in the
preceding item. Select NTLM when the domain controller is
Windows NT or Kerberos for Windows 2000 Server or
Windows Server 2003.
Keyboard Login This determines whether login authentication is allowed via
the machine operation panel or not, despite the IC card
authentication is activated (using the IC card authentication
kit installed).
COMMAND CENTER Pages
Operation Guide 49
user’s settings on the basic page, and the user's document box and shared document
box pages.
Advanced > Management > Authentication > Network User Property
This allows to obtain user information at authenticating the user over the network.
Advanced > Management > Authentication > Group Authorization Set.
After the network authentication has been established by executing Advanced >
Management > Authentication > General on page 48, you can add a group to specify
the Group Information and items for Job Authorization Settings.
Up to 20 group accounts are registerable. By default, a group account (Other) has been
preset. This is used to process any group account which does not fall within the
registered groups.
Adding a New Group
1. Click Group Authorization Set., open the Group Authorization Set. page.
2. Click Add and specify group information and Permit or Prohibit.
3. Click Submit.
Item Description
Obtain Network
User Property
Turned On to obtain user information.
LDAP Server
Name
Specifies a name or IP address for the LDAP server.
LDAP Port
Number
Specifies a port number for LDAP or use the LDAP default
port 389.
Search Timeout Specifies a period of time for searching the LDAP server.
LDAP
Encryption
Selects the type of encryption according to the type of
security employed by the LDAP server. Select Off when
encryption is not used.
Name 1 (2) Specifies the LDAP attribute to obtain a user name for
display, from the LDAP server.
E-mail Address Specifies the LDAP attribute to obtain an e-mail address from
the LDAP server.
Item Description
Group
Authorization
Turned On if you want to individually authorize or de-
authorize the groups
Number of
Registered
Groups
The number of the groups currently registered.
COMMAND CENTER Pages
50 KYOCERA COMMAND CENTER
Editing a User Login
1. Click Group Authorization Set., open the Group Authorization Set. page.
2. Click the desired Group ID or Group Name to edit the group and modify their
information.
3. Click Submit.
Deleting a User Login
1. Click Group Authorization Set., open the Group Authorization Set. page.
2. Check the desired group. When the check box on the left side of Group ID is selected,
all groups displayed on the page will be checked.
3. Click Delete.
The Group Authorization Set. - Delete page appears. You can confirm the groups to
be deleted.
4. Click Delete when the desired groups are selected.
Advanced > Management > Notification/Maintenance > Maintenance
Notification
This feature defines the recipient of maintenance information reports.
Item Description
Equipment ID This is the name by which the machine will be identified.
Recipient
Address
The E-mail address of the recipient. If there is more than one
recipient then the addresses should be separated by a semi-
colon ";".
Subject You can include model name, serial number, MAC address
and equipment ID in the subject line as follows: Enter one of
the following conversion strings starting with %. The string
will be converted into a pre-defined string to display the
above information.
- %printer = Model
- %serial = Serial Number
- %etheraddr = MAC Address
- %equipid = Equipment ID
E-mail Interval Sets the time or interval for sending the status information.
Events will be reported at the specified interval.
•None: No report is sent.
•Monthly: Sends on the specified time of specified month.
•Weekly: Sends on the specified time of every week.
•Daily: Sends at the specified time of every day.
•Hourly: Sends at the specified interval every hour.
If a specified day does not exist in the month, such as the
31st, the last day of the month is used as the specified day.
Run once now You can test this by clicking the Send button to immediately
send a report.
COMMAND CENTER Pages
Operation Guide 51
Advanced > Management > Maintenance Notification > Sending Log
History
This feature defines the Job Log Notification information reports.
Advanced > Security > Secure Protocols
You can encrypt communication between a PC and this machine using SSL encryption.
Item Description
Recipient
Address
The E-mail address of the recipient. If there is more than one
recipient then the addresses should be separated by a semi-
colon ";".
Job Log
Subject
You can include model name, serial number, and MAC
address in the subject line as follows: Enter one of the
following conversion strings starting with %. The string will be
converted into a pre-defined string to display the above
information.
- %printer = Model
- %serial = Serial Number
- %etheraddr = MAC Address
Auto Sending Determines whether the job log report is sent or not. Set this
to On to send the report.
Jobs Set the number of job logs for sending, from 1 to 1500.
Run once now You can test this by clicking the Send button to immediately
send a report.
Item Description
SSL Specifies whether or not to use the SSL protocol.
Serverside
Settings
Effective
Encryption
Selects the encryption algorithm(s) to be used.
HTTP
Security
Specifies the security level.
Secure
Only
(HTTPS)
Encrypts all communication. Access is possible only with a
URL that begins with "https://." Access attempts using an
ordinary http:// URL are automatically redirected to the URL
where "http://" is replaced with "https://."
Not
Secure
(HTTPS &
HTTP)
Enables access for both encrypted and unencrypted
communication. Access is possible with https:// and http://
URLs. The former URL establishes encrypted communication
and the latter establishes normal communication.
IPP Security
Specifies the security level.
COMMAND CENTER Pages
52 KYOCERA COMMAND CENTER
NOTE: When the SSL is set to On and HTTP Security is set to Secure (HTTPS), the
document boxes cannot be accessed the TWAIN driver.
Advanced > Security > IEEE802.1x
The IEEE802.1x security protocol allows the user to login to the secured networks based
on the client certificates.
Secure
Only (IPP
over SSL)
Encrypts all communications.
Not
Secure
(IPP over
SSL&IPP)
Enables access for both encrypted and unencrypted
communications.
Clientside
Settings
Effective
Encryption
Allow you to specify the encryption algorithm for data
communication. You can use more than one algorithms at a
time.
Certificate
Verification
When set On, verify the expiration of the server certificate at
communication. If found expired, communication will fail.
When set Off, the expiration will not be verified.
Item Description
Item Description
IEEE802.1x Specifies whether or not to use the IEEE802.1x protocol.
Authentication
Type
Selects either EAP-TLS or PEAP (EAP-MS-CHAPv2) for the
authentication type.
Login User
Name
Enter the name of the user who accesses the printing
system. The IEEE802.1x client certificate of this user must
be valid.
Login Password You can set a PEAP-based password. (This setting is valid
when PEAP (EAP-MS-CHAPv2) authentication type is
selected.)
Common Name
Specifies the common name of the server certificate if the
server is required to be authenticated. (This setting is valid
when PEAP (EAP-MS-CHAPv2) authentication type is
selected.)
Match Rule of
Common Name
When the server certificate is verified, the common name
specified under
Common Name
is compared with the
common name on the server certificate. This item allows you
to specify whether the common names are considered to be
matched if they exactly or partially match. (This setting is valid
when PEAP (EAP-MS-CHAPv2) authentication type is
selected.)
COMMAND CENTER Pages
Operation Guide 53
Advanced > Security > IPSec > General
This page allows you to set access restrictions for IPSec protocol-based communication.
Advanced > Security > IPSec > Rule1 (to Rule3)
These pages allow you to select or edit rules to use for IPSec protocol-based communication.
Certificate
Status
Displays whether the certificate is
active
or not.
Item Description
Item Description
IPSec Specifies whether or not to enable the IPSec protocol. Select
On to enable the IPSec protocol. Select Off to disable it.
Restriction
Specifies the default policy for non-IPSec packets.
Select
Allow
to allow communication with all hosts and
networks including those not permitted by the rules described
under Advanced > Security > IPSec > Rule1 (to Rule3) on
page 53. Select
Deny
to allow communication only with the
hosts and networks permitted by the rules.
Authentication
Type
Specifies the authentication type used for IKE phase1. To set
a character string as the shared key and use it for
communication, select Pre-shared and enter the string of
the pre-shared key in the text box. To use a CA-issued
device certificate or root certificate, select Certificates.
When Expiration Verification is enabled, the expiration of
the server certificate is verified at communicating. If the
server certificate is found expired, communication will fail.
When it is disabled, the expiration will not be verified.
When you select Certificates, the contents of the CA
certificate and root 1 to 3 certificates are displayed if they are
enabled. When you click the CA or Root button, you can
view, import or delete CA-issued or root certificates.
Rule1 (to Rule3)
Shows whether the set rule is enabled or disabled. To enable
or disable the rule, refer to Advanced > Security > IPSec >
Rule1 (to Rule3) on page 53.
Item Description
Rule Specifies whether or not to enable the selected IPSec policy
rule. Select On to enable the rule. Select Off to disable it.
Key Exchange
(IKE phase1)
When using IKE phase1, a secure connection with the other
end is established by generating ISAKMP SAs. Configure the
following items so that they meet the requirement of the other
end.
COMMAND CENTER Pages
54 KYOCERA COMMAND CENTER
Mode Main Mode protects identifications but requires more
messages to be exchanged with the other end. Aggressive
Mode requires fewer messages to be exchanged with the
other end than Main Mode but restricts identification
protection and narrows the extent of the parameter
negotiations. When Aggressive Mode is selected and Pre-
shared is selected for Authentication Type, only host
addresses can be specified for IP addresses of the rule.
Hash
Selects the hash algorithm.
Encryption
Selects the encryption algorithm.
Diffie-
Hellman
Group
The Diffie-Hellman key-sharing algorithm allows two hosts on
an unsecured network to share a private key securely. Select
the Diffie-Hellman group to use for key sharing.
Lifetime
(Time)
Specifies the lifetime of an ISAKMP SA in seconds.
Data Protection
(IKE phase2)
In IKE phase2, IPSec SAs such as AH or ESP are established
by using SAs established in IKE phase1. Configure the
following items so that they meet the requirement of the other
end.
Protocol
Select
ESP
or
AH
for the protocol.
ESP
protects the privacy
and integrity of the packet contents. Select the hash algorithm
and encryption algorithm below.
AH
protects the integrity of
the packet contents using encryption checksum. Select the
hash algorithm below.
Hash
Selects the hash algorithm.
Encryption
Selects the encryption algorithm. (When
ESP
is selected
under
Protocol
.)
PFS
When
PFS
is set to
On
(enabled), even if a key is decrypted,
the decrypted key cannot be used to decrypt the other keys
generated after the decryption. This improves the safety, but
imposes a heavy burden because of more key-generation
processes.
Diffie-
Hellman
Group
The Diffie-Hellman key-sharing algorithm allows two hosts on
an unsecured network to share a private key securely. Select
the Diffie-Hellman group to use for key sharing.
Lifetime
Measure-
ment
Specifies whether the lifetime is measured by time or by time
and data size.
Lifetime
(Time)/
Lifetime
(Data
Size)
Specifies the lifetime of an IPSec SA.
Lifetime Measurement
allows you to select whether to use time or data size to specify
the lifetime. When you select
Time & Data Size
, an SA is
disabled and updated when either the time or data size of the
SA exceeds the specified value.
IP Version
Specifies the IP version of the other end. Select
IPv4
or
IPv6
.
Item Description
COMMAND CENTER Pages
Operation Guide 55
IP
Address
(IPv4)
Specifies the IPv4 addresses of the hosts or network with
which the print system is connecting via IPSec. When you are
restricting the scope of IPSec, be sure to specify the IP
addresses. If this field is blank, all IPv4 addresses will be
allowed to connect the print system.
IP
Address
(IPv6)
Specifies the IPv6 addresses of the hosts or network with
which the print system is connecting via IPSec. When you are
restricting the scope of IPSec, be sure to specify the IP
addresses. If this field is blank, all IPv6 addresses will be
allowed to connect the print system.
Subnet
Mask
When
IPv4
is selected for
IP Version
, this specifies the
subnet mask of the hosts or network with which the print
system is connecting via IPSec. If this field is blank, the
specified addresses are considered to be host addresses.
Prefix
Length
When
IPv6
is selected for
IP Version
, this specifies the prefix
length of the hosts or network with which the print system is
connecting via IPSec. If this field is blank, the specified
addresses are considered to be host addresses.
Item Description
Troubleshooting
56 KYOCERA COMMAND CENTER
4 Troubleshooting
Consult the table below to find basic solutions for problems you may encounter with
COMMAND CENTER.
Symptom Check Items Corrective Action Reference
I can’t access
COMMAND
CENTER.
Is the power turned on
to this machine?
Turn the power on to
this machine, wait until
it is a ready state, and
try to access
COMMAND CENTER.
Operation
Guide
Is the network cable
properly connected?
Connect the network
cable properly.
Operation
Guide
Are the network
settings that are made
in this machine
correct?
Perform the network
settings from the
operation panel.
Contact your network
administrator for the
appropriate settings.
-
Is the IP address for
this machine entered
correctly?
Enter the correct IP
address. Check this
machine IP address
with your network
administrator.
-
Are the LAN settings
that are made in Web
browser correct?
Check the settings
made in Web browser.
Refer to the Help
function in your
browser.
-
Has the administrator
set up an IP Filter
function?
Access COMMAND
CENTER from an
approved IP address.
page 38
Is HTTP Security on
the Advanced >
Security > Secure
Protocol page set to
Secure (HTTPS)?
When HTTP Security is
set to Secure (HTTPS),
specify a URL that
begins with https://. You
cannot access
COMMAND CENTER
with an http:// URL.
page 51
Does the version of
your browser
application support
operation using
COMMAND
CENTER?
Use a browser
application that
supports COMMAND
CENTER.
page 1
Troubleshooting
Operation Guide 57
Characters do
not display
properly in
COMMAND
CENTER.
Does the version of
your browser
application support
operation using
COMMAND
CENTER?
Use a browser
application that
supports COMMAND
CENTER.
page 1
Is the same language
as that displayed on
the operation panel
selected?
Select the same
language as that
displayed on the
operation panel.
page 9
I can’t access
the other
pages.
Has the administrator
set a password?
Enter the password. page 12
I can’t perform
settings.
Is the printer or
scanner currently in
operation?
Wait until the operation
has been completed.
-
The settings I
made are not
registered.
Did you click the
Submit button after
making the settings?
Click the Submit button
and move to another
page or close
COMMAND CENTER
window.
-
Did you click the
Restart button after
making the settings?
Restart this machine.
All settings will be
registered.
page 9
Are you using the
System menu on this
machine's panel while
COMMAND CENTER
is being operated?
Operate COMMAND
CENTER after you
have finished with the
System menu.
-
The
administrator
has forgotten
the Admin
password.
- Contact your dealer or
service center.
-
Error or
Warning is
displayed
under the
STATUS
indicator.
Is there an error
message shown in the
display?
Perform the
troubleshooting
procedure the
messages suggests
referring to the
Operation Guide.
Operation
Guide
Symptom Check Items Corrective Action Reference
Rev. 5.3W 2009.10