Table of Contents
- About this manual
- Chapter 1. Safety information
- Chapter 2. General checkout
- Chapter 3. Idetifying FRU (CRU)
- Chapter 4. Removing a FRU or CRU
- Service tools
- General guidelines
- Remove the lower case
- Remove the battery pack
- Remove the speakers
- Remove the WLAN card
- Remove the coin-cell battery
- Remove the solid-state drive
- Remove the heat sink
- Remove the system board
- Remove the audio board
- Remove the touchpad
- Remove the upper case (with keyboard)
- Remove the LCD bezel
- Remove the hinge cover
- Remove the hinges
- Remove the LCD panel
- Remove the camera
- Trademarks
Lenovo 1 User Manual
Displayed below is the user manual for 1 by Lenovo which is a product in the Notebooks category. This manual has pages.
Related Manuals
IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05)
Hardware Maintenance Manual
First Edition (December 2019)
© Copyright Lenovo 2019.
Contents
About this manual . . . . . . . . . . . . iii
Chapter 1. Safety information . . . . . . 1
General safety . . . . . . . . . . . . . . . . 1
Electrical safety . . . . . . . . . . . . . . . . 1
Safety inspection guide . . . . . . . . . . . . . 2
Handling devices that are sensitive to electrostatic
discharge . . . . . . . . . . . . . . . . . . 3
Grounding requirements . . . . . . . . . . . . 4
Safety notices (multilingual translations) . . . . . . 4
Chapter 2. General checkout . . . . . 21
What to do first . . . . . . . . . . . . . . . 21
CRU list . . . . . . . . . . . . . . . . . . 22
Chapter 3. Idetifying FRU (CRU) . . . 23
Locate FRU and CRU . . . . . . . . . . . . 23
Chapter 4. Removing a FRU or
CRU . . . . . . . . . . . . . . . . . . 27
Service tools . . . . . . . . . . . . . . . . 27
General guidelines. . . . . . . . . . . . . . 27
Remove the lower case . . . . . . . . . . . . 28
Remove the battery pack . . . . . . . . . . . 29
Remove the speakers . . . . . . . . . . . . 31
Remove the WLAN card . . . . . . . . . . . 32
Remove the coin-cell battery. . . . . . . . . . 33
Remove the solid-state drive. . . . . . . . . . 34
Remove the heat sink . . . . . . . . . . . . 36
Remove the system board. . . . . . . . . . . 38
Remove the audio board . . . . . . . . . . . 39
Remove the touchpad . . . . . . . . . . . . 42
Remove the upper case (with keyboard) . . . . . 43
Remove the LCD bezel . . . . . . . . . . . . 46
Remove the hinge cover . . . . . . . . . . . 46
Remove the hinges . . . . . . . . . . . . . 47
Remove the LCD panel . . . . . . . . . . . . 48
Remove the camera . . . . . . . . . . . . . 50
Trademarks . . . . . . . . . . . . . . . . . liii
© Copyright Lenovo 2019 i
ii IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
About this manual
This manual contains service and reference information for the following Lenovo products.
Machine Machine type (MT)
Lenovo IdeaPad 1 11IGL05 81VT
Lenovo IdeaPad 1 14IGL05 81VU
Important:
• This manual is intended only for trained service technicians who are familiar with Lenovo products.
• Before servicing a Lenovo product, be sure to read all the information under Chapter 1 “Safety
information” on page 1.
© Copyright Lenovo 2019 iii
iv IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
Chapter 1. Safety information
This chapter presents the following safety information that you need to be familiar with before you service a
Lenovo notebook computer.
General safety
Follow these rules to ensure general safety:
• Observe good housekeeping in the area of the machines during and after maintenance.
• When lifting any heavy object:
1. Make sure that you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift.
4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the
muscles in your back. Do not attempt to lift any object that weighs more than 16 kg (35 lb) or that you
think is too heavy for you.
• Do not perform any action that causes hazards to the customer or that makes the equipment unsafe.
• Before you start the machine, make sure that other service technicians and the customer's personnel are
not in a hazardous position.
• Place removed covers and other parts in a safe place, away from all personnel, while you are servicing the
machine.
• Keep your tool case away from walk areas so that other people will not trip over it.
• Do not wear loose clothing that can be trapped in the moving parts of a machine. Make sure that your
sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it.
• Insert the ends of your necktie or scarf inside clothing or fasten it with a non-conductive clip, about 8
centimeters (3 inches) from the end.
• Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing.
Attention: Metal objects are good electrical conductors.
• Wear safety glasses when you are hammering, drilling, soldering, cutting wire, attaching springs, using
solvents, or working in any other conditions that might be hazardous to your eyes.
• After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that
is worn or defective.
• Reinstall all covers correctly before returning the machine to the customer.
• Fan louvers on the machine help to prevent overheating of internal components. Do not obstruct fan
louvers or cover them with labels or stickers.
Electrical safety
Observe the following rules when working on electrical equipment.
Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft
material that does not insulate you when working with live electrical currents. Many customers have, near
their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges.
Do not use this type of mat to protect yourself from electrical shock.
• Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet. If an electrical
accident occurs, you can then operate the switch or unplug the power cord quickly.
• Do not work alone under hazardous conditions or near equipment that has hazardous voltages.
• Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
© Copyright Lenovo 2019 1
– Removing or installing main units
• Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer
to power-off the wall box that supplies power to the machine and to lock the wall box in the off position.
• If you need to work on a machine that has exposed electrical circuits, observe the following precautions:
– Ensure that another person, familiar with the power-off controls, is near you.
Attention: Another person must be there to switch off the power, if necessary.
– Use only one hand when working with powered-on electrical equipment; keep the other hand in your
pocket or behind your back.
Attention: An electrical shock can occur only when there is a complete circuit. By observing the above
rule, you may prevent a current from passing through your body.
– When using testers, set the controls correctly and use the approved probe leads and accessories for
that tester.
– Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as
metal floor strips and machine frames.
Observe the special safety precautions when you work with very high voltages. Instructions for these
precautions are in the safety sections of maintenance information. Use extreme care when measuring high
voltages.
• Regularly inspect and maintain your electrical hand tools for safe operational condition.
• Do not use worn or broken tools and testers.
• Never assume that power has been disconnected from a circuit. First, check that it has been powered off.
• Always look carefully for possible hazards in your work area. Examples of these hazards are wet floors,
non-grounded power extension cables, power surges, and missing safety grounds.
• Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is
conductive; such touching can cause personal injury and machine damage.
• Do not service the following parts with the power on when they are removed from their normal operating
places in a machine:
– Power supply units
– Pumps
– Blowers and fans
– Motor generators
– Similar units as listed above
This practice ensures correct grounding of the units.
• If an electrical accident occurs:
– Use caution; do not become a victim yourself.
– Switch off power.
– Send another person to get medical aid.
Safety inspection guide
The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each
machine was designed and built, required safety items were installed to protect users and service
technicians from injury. This guide addresses only those items. You should use good judgment to identify
potential safety hazards due to attachment of non-Lenovo features or options not covered by this inspection
guide.
If any unsafe conditions are present, you must determine how serious the apparent hazard could be and
whether you can continue without first correcting the problem.
Consider these conditions and the safety hazards they present:
• Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal
electrical shock)
• Explosive hazards, such as a damaged cathode ray tube (CRT) face or a bulging capacitor
• Mechanical hazards, such as loose or missing hardware
2IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
To determine whether there are any potentially unsafe conditions, use the following checklist at the
beginning of every service task. Begin the checks with the power off, and the power cord disconnected.
Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Power off the computer. Disconnect the power cord.
3. Check the power cord for:
a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground
continuity for 0.1 ohm or less between the external ground pin and the frame ground.
b. The power cord should be the authorized type specified for your computer. Go to: http://
www.lenovo.com/serviceparts-lookup
c. Insulation must not be frayed or worn.
4. Check for cracked or bulging batteries.
5. Remove the cover.
6. Check for any obvious non-Lenovo alterations. Use good judgment as to the safety of any non-Lenovo
alterations.
7. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or
other liquids, or signs of fire or smoke damage.
8. Check for worn, frayed, or pinched cables.
9. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered
with.
Handling devices that are sensitive to electrostatic discharge
Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to
electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects.
Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the
person handling the part are all at the same charge.
Notes:
1. Use product-specific ESD procedures when they exceed the requirements noted here.
2. Make sure that the ESD protective devices you use have been certified (ISO 9000) as fully effective.
When handling ESD-sensitive parts:
• Keep the parts in protective packages until they are inserted into the product.
• Avoid contact with other people.
• Wear a grounded wrist strap against your skin to eliminate static on your body.
• Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when
you are wearing a wrist strap.
• Use a grounded work mat to provide a static-free work surface. The mat is especially useful when
handling ESD-sensitive devices.
• Select a grounding system, such as those listed below, to provide protection that meets the specific
service requirement.
Note: The use of a grounding system to guard against ESD damage is desirable but not necessary.
– Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground.
– When working on a double-insulated or battery-operated system, use an ESD common ground or
reference point. You can use coax or connector-outside shells on these systems.
– Use the round ground prong of the ac plug on ac-operated computers.
Chapter 1.Safety information 3
Grounding requirements
Electrical grounding of the computer is required for operator safety and correct system function. Proper
grounding of the electrical outlet can be verified by a certified electrician.
Safety notices (multilingual translations)
The safety notices in this section are provided in the following languages:
• English
• Arabic
• Brazilian Portuguese
• French
• German
• Hebrew
• Japanese
• Korean
• Spanish
• Traditional Chinese
DANGER
DANGER
DANGER
4IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
6IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
PERIGO
PERIGO
PERIGO
PERIGO
PERIGO
8IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
DANGER
DANGER
DANGER
DANGER
VORSICHT
10 IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
VORSICHT
VORSICHT
VORSICHT
12 IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
14 IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
16 IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
18 IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
20 IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
Chapter 2. General checkout
This chapter contains the following topics:
Before you go to the checkout instructions, ensure that you read the following important notes.
Important notes:
• Only certified trained personnel should service the computer.
• Before replacing any FRU, read the entire page on removing and replacing FRU.
• Be extremely careful during such write operations as copying, saving, or formatting. Drives in the computer
that you are servicing sequence might have been altered. If you select an incorrect drive, data or programs might be
overwritten.
• Replace a FRU only with another FRU of the correct model. When you replace a FRU, make sure that the model
of the machine and the FRU part number are correct by referring to the FRU parts list.
• A FRU should not be replaced because of a single, unreproducible failure. Single failures can occur for a variety
of reasons that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or
software errors. Consider replacing a FRU only when a problem recurs. If you suspect that a FRU is defective, clear
the error log and run the test again. If the error does not recur, do not replace the FRU.
• Be careful not to replace a nondefective FRU.
What to do first
When you return a FRU, you must include the following information in the parts exchange form or parts return
form that you attach to it:
1. Name and phone number of service technician
2. Date of service
3. Date on which the machine failed
4. Date of purchase
5. Failure symptoms, error codes appearing on the display, and beep symptoms
6. Procedure index and page number in which the failing FRU was detected
7. Failing FRU name and part number
8. Machine type, model number, and serial number
9. Customer's name and address
Note: During the warranty period, the customer may be responsible for repair costs if the computer damage
was caused by misuse, accident, modification, unsuitable physical or operating environment, or improper
maintenance by the customer. Following is a list of some common items that are not covered under warranty
and some symptoms that might indicate that the system was subjected to stress beyond normal use.
Before checking problems with the computer, determine whether the damage is covered under the warranty
by referring to the following list:
The following are not covered under warranty:
• LCD panel cracked from the application of excessive force or from being dropped
• Scratched (cosmetic) parts
• Distortion, deformation, or discoloration of the cosmetic parts
• Plastic parts, latches, pins, or connectors that have been cracked or broken by excessive force
• Damage caused by liquid spilled into the system
© Copyright Lenovo 2019 21
• Damage caused by the improper insertion of a personal-computer card (PC card) or the installation of an
incompatible card
• Improper disc insertion or use of an external optical drive
• Fuses blown by attachment of a non-supported device
• Forgotten computer password (making the computer unusable)
• Sticky keys caused by spilling a liquid onto the keyboard
• Use of an incorrect ac power adapter on laptop products
The following symptoms might indicate damage caused by non-warranted activities:
• Missing parts might be a symptom of unauthorized service or modification.
• Check for obvious damage to a hard disk drive. If the spindle of a hard disk drive becomes noisy, the hard
disk drive might have been dropped or subject to excessive force.
CRU list
Table 1. Model: Lenovo IdeaPad 1 11IGL05 (Machine type: 81VT)
CRU Type
ac power adapter self-service
Table 2. Model: Lenovo IdeaPad 1 14IGL05 (Machine type: 81VU)
CRU Type
ac power adapter self-service
22 IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
Chapter 3. Idetifying FRU (CRU)
Locate FRU and CRU
The exploded illustrations help Lenovo service technicians identify FRU or CRU that they may need to
replace when servicing a customer’s computer.
© Copyright Lenovo 2019 23
Figure 1. Lenovo IdeaPad 1 11IGL05 and Lenovo IdeaPad 1 14IGL05 exploded view
Table 3. FRU (CRU) categories
No. FRU (CRU) category
1LCD cover
2Hinge cap
3Hinges
24 IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
Table 3. FRU (CRU) categories (continued)
4Camera
5LCD panel
6LCD Bezel
7Upper case (with keyboard)
8Touchpad
9WLAN card
10 Audio board with cable
11 Coin-cell battery
12 Battery pack
13 Speakers
14 Lower case
15 Heat sink
16 Solid-state drive (SSD) bracket
17 Solid-state drive (SSD)
18 System board
19 Removable tapes
20 EDP cable
Chapter 3.Idetifying FRU (CRU) 25
26 IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
Chapter 4. Removing a FRU or CRU
Service tools
The following table lists tools for servicing Lenovo computers. Tools with a cross mark are needed for
servicing the product models as described by this publication. Prepare them before you service the product.
Table 4. Service tools
Service tool and consumable Model applicability
Screwdriver (Phillips head) (PH1/PH01) X
Screwdriver (Torx head) (T5)
Screwdriver (Torx head) (T30)
Pry tool 1 X
Tweezers (conductive) X
Tweezers (isolated)
Suction cup
Hexagonal socket
Silicone grease
Acetate tape X
Polyamide tape
Mylar tape
Electrical tape
Double-sided tape
Conductive tape
Eraser
Heat gun
Brown brush
Notes:
• T30 screwdrivers are used to service the new Intel Xeon CPUs.
• Hexagonal sockets are used to remove antenna connectors.
• Silicone grease is applied to the CPU and heat sink surfaces to eliminate air gaps.
General guidelines
When removing or replacing a FRU, ensure that you observe the following general guidelines:
1. Do not try to service any computer unless you have been trained and certified. An untrained person runs
the risk of damaging parts.
2. Begin by removing any FRU that have to be removed before replacing the failing FRU. Any such FRU are
listed at the beginning of each FRU replacement procedure. Remove them in the order in which they are
listed.
© Copyright Lenovo 2019 27
3. Follow the correct sequence in the steps for removing a FRU, as shown in the illustrations by the
numbers in square callouts.
4. When removing a FRU, move it in the direction as shown by the arrow in the illustration.
5. To install a new FRU in place, perform the removal procedure in reverse and follow any notes that
pertain to replacement.
6. When replacing a FRU, carefully retain and reuse all screws.
7. When replacing the base cover, reapply all labels that come with the replacement base cover. If some
original labels are not included with the replacement base cover, peel them off from the original base
cover and paste them on the replacement base cover.
DANGER
Before removing any FRU or CRU, shut down the computer and unplug all power cords from
electrical outlets.
Attention: After replacing a FRU, do not turn on the computer until you have ensured that all screws,
springs, and other small parts are in place and none are loose inside the computer. Verify this by shaking the
computer gently and listening for rattling sounds. Metallic parts or metal flakes can cause electrical short
circuits.
Attention: The system board is sensitive to and can be damaged by ESD. Before touching it, establish
personal grounding by touching a ground point with one hand or by using an ESD strap (P/N 6405959).
Remove the lower case
Make sure the computer has been shut down before servicing the computer.
Step 1. Disconnect all the power cords, cables, and USB devices from the computer.
Step 2. Place the computer upside down on a flat surface.
Step 3. Remove ten screws.
Figure 2. Remove ten screws
28 IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
Screw specifications Number of screws
M2 x L4 10
Step 4. Release the cover from the hinges. Then, remove the lower case.
Figure 3. Release the cover and remove the lower case
Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement
part:
Lower case
Remove the battery pack
Make sure the following FRU (or CRU) has been removed.
“Remove the lower case” on page 28
Step 1. Disconnect the battery pack cable from the system board.
Attention: Do not pull the cable. Use your fingernail to disconnect the cable.
Chapter 4.Removing a FRU or CRU 29
Figure 4. Disconnect the battery cable
Step 2. Remove five screws. Then, remove the battery pack.
Figure 5. Remove five screws and remove the battery pack
Screw specifications Number of screws
M2 x L4 5
Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement
part:
Battery pack
30 IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
Remove the speakers
Make sure the following FRU (CRU) have been removed.
“Remove the lower case” on page 28
Step 1. Disconnect the battery pack cable from the system board.
Attention: Do not pull the cable. Use your fingernail to disconnect the cable.
Figure 6. Disconnect the battery pack cable
Step 2. Disconnect the speaker cable from the system board. Then, carefully remove the speakers.
Figure 7. Disconnect the speaker cable and remove the speakers
Chapter 4.Removing a FRU or CRU 31
Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement
part:
Speakers
Remove the WLAN card
Make sure the following FRU (or CRU) have been removed.
“Remove the lower case” on page 28
Step 1. Disconnect the battery pack cable from the system board.
Attention: Do not pull the cable. Use your fingernail to disconnect the cable.
Figure 8. Disconnect the battery pack cable
Step 2. Disconnect the wireless antenna cable. Then, remove one screw and slide the WLAN card out of
the slot.
32 IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
Figure 9. Disconnect the wireless antenna cable, remove one screw and slide the WLAN card out of the slot
Screw specifications Number of screws
M2 x L2.5 1
Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement
part:
WLAN card
Remove the coin-cell battery
Make sure the following FRU (CRU) have been removed:
“Remove the lower case” on page 28
Step 1. Disconnect the battery pack cable from the system board.
Attention: Do not pull the cable. Use your fingernail to disconnect the cable.
Chapter 4.Removing a FRU or CRU 33
Figure 10. Disconnect the battery pack cable
Step 2. Disconnect the coin-cell battery cable from the system board. Then, remove the coin-cell battery.
Figure 11. Disconnect the coin-cell battery cable from the system board and remove the coin-cell battery
Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement
part:
Coin-cell battery
Remove the solid-state drive
Make sure the following FRU (CRU) have been removed:
34 IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
“Remove the lower case” on page 28
Step 1. Disconnect the battery pack cable from the system board.
Attention: Do not pull the cable. Use your fingernail to disconnect the cable.
Figure 12. Disconnect the battery pack cable
Step 2. Remove one screw. Then, remove the solid-state drive.
Figure 13. Remove one screw and then remove the solid-state drive
Screw specifications Number of screws
M2 x L2.5 1
Chapter 4.Removing a FRU or CRU 35
Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement
part:
Solid-state drive
Remove the heat sink
Make sure the following FRU (or CRU) have been removed.
“Remove the lower case” on page 28
Step 1. Disconnect the battery pack cable from the system board.
Attention: Do not pull the cable. Use your fingernail to disconnect the cable.
Figure 14. Disconnect the battery pack cable
Step 2. Loosen four screws.
36 IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
Figure 15. Loosen four screws
Screw specifications Number of screws
M2 x L2.5 4
Step 3. Remove three screws. Then, remove the heat sink.
Figure 16. Remove three screws and remove the heat sink
Screw specifications Number of screws
M2 x L2.5 3
Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement
part:
Heat sink
Chapter 4.Removing a FRU or CRU 37
Remove the system board
Make sure the following FRU (or CRU) have been removed.
“Remove the lower case” on page 28
“Remove the battery pack” on page 29
“Remove the WLAN card” on page 32
“Remove the heat sink” on page 36
Step 1. Disconnect the cables connected to the system board. Then, remove two screws from the hinges
and open the hinges.
Figure 17. Disconnect the cables and remove two screws
Screw specifications Number of screws
M2 x L4 2
Step 2. Remove three screws. Then, remove the system board.
38 IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
Figure 18. Remove three screws remove the system board
Screw specifications Number of screws
M2 x L2.5 3
Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement
part:
System board
Remove the audio board
Make sure the following FRU (or CRU) have been removed.
“Remove the lower case” on page 28
Step 1. Disconnect the battery pack cable from the system board.
Attention: Do not pull the cable. Use your fingernail to disconnect the cable.
Chapter 4.Removing a FRU or CRU 39
Figure 19. Disconnect the battery pack cable
Step 2. Disconnect the audio cable connector.
Figure 20. Disconnect the audio cable connector
Screw specifications Number of screws
M2 x L4 2
Step 3. Remove two screws from the hinge and open the hinge.
40 IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
Figure 21. Remove two screws from the hinge and open the hinge
Step 4. Remove one screw. Then, remove the audio board.
Figure 22. Remove one screw and remove the audio board
Screw specifications Number of screws
M2 x L2 1
Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement
part:
Audio board
Chapter 4.Removing a FRU or CRU 41
Remove the touchpad
Make sure the following FRU (or CRU) have been removed.
“Remove the lower case” on page 28
“Remove the battery pack” on page 29
“Remove the system board” on page 38
Step 1. Disconnect the touchpad cable. Then, remove three screws.
Figure 23. Disconnect the touchpad cable and remove three screws
Screw specifications Number of screws
M2 x L2 3
Step 2. Remove the touchpad out of the system board.
42 IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
Figure 24. Remove the touchpad out of the system board
Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement
part:
Touchpad
Remove the upper case (with keyboard)
Make sure the following FRUs (CRUs) have been removed.
“Remove the lower case” on page 28
“Remove the battery pack” on page 29
“Remove the heat sink” on page 36
Step 1. Disconnect the battery pack cable from the system board.
Attention: Do not pull the cable. Use your fingernail to disconnect the cable.
Chapter 4.Removing a FRU or CRU 43
Figure 25. Disconnect the battery pack cable
Step 2. Disconnect the cables from the system board.
Figure 26. Disconnect the cables from the system board
Step 3. Remove four screws. Then, open the hinges.
44 IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
Figure 27. Remove four screws and open the hinges
Screw specifications Number of screws
M2 x L4 4
Step 4. Slowly and carefully lift up the upper case.
Figure 28. Slowly and carefully lift up the upper case
Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
Upper case (with keyboard)
Chapter 4.Removing a FRU or CRU 45
Remove the LCD bezel
Make sure the following FRU (or CRU) have been removed.
“Remove the lower case” on page 28
Step 1. Insert your fingernails under the lower inner side of the LCD bezel and carefully pull the LCD bezel
outwards. Repeat this action along the inner edges of the LCD bezel until all hooks that secure the
LCD bezel are detached.
Attention: Do not pull the LCD bezel from the outer sides of the LCD bezel. Pulling the LCD bezel
from the outer side may damage the hooks.
Note: The lower side of the LCD bezel is fixed to the LCD panel with adhesive tape. Detach with
care.
Figure 29. Pull the inner sides of the LCD bezel
Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement
parts:
LCD bezel
Remove the hinge cover
Make sure the following FRUs (or CRUs) have been removed.
“Remove the LCD bezel” on page 46
Step 1. Slide the hinge cover from left to right and remove the hinge cover.
46 IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
Figure 30. Remove the hinge cover
Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement
part:
Hinge cover
Remove the hinges
Make sure the following FRU (or CRU) have been removed.
“Remove the lower case” on page 28
“Remove the upper case (with keyboard)” on page 43
“Remove the LCD bezel” on page 46
“Remove the hinge cover” on page 46
Step 1. Remove eight screws. Then, remove the hinges.
Chapter 4.Removing a FRU or CRU 47
Figure 31. Remove eight screws
Callout Screw specifications Number of screws
1 M2 x L2 6
2 M2 x L2.5 2
Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement
part:
Hinges
Remove the LCD panel
Make sure the following FRU (or CRU) have been removed.
“Remove the lower case” on page 28
“Remove the upper case (with keyboard)” on page 43
“Remove the LCD bezel” on page 46
“Remove the hinge cover” on page 46
“Remove the hinges” on page 47
Step 1. Pull the removable tapes outwards steadily.
48 IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
Figure 32. Pull the removable tapes
Step 2. Carefully rotate the LCD panel so that the rear side of LCD panel is facing up.
Attention: LCD panel is connected by a cable on the back side. Rotate panel carefully.
Figure 33. Rotate the LCD panel
Step 3. Disconnect the LCD cable and remove the LCD panel.
Chapter 4.Removing a FRU or CRU 49
Figure 34. Disconnect the LCD cable and remove the LCD panel
Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement parts:
LCD panel
Remove the camera
Make sure the following FRU (or CRU) have been removed.
“Remove the lower case” on page 28
“Remove the upper case (with keyboard)” on page 43
“Remove the LCD bezel” on page 46
“Remove the LCD panel” on page 48
Step 1. Disconnect the camera cable and remove the camera.
50 IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
52 IdeaPad 1 (11", 05) and IdeaPad 1 (14", 05) Hardware Maintenance Manual
Trademarks
LENOVO and the LENOVO logo are trademarks of Lenovo.
All other trademarks are the property of their respective owners. © 2019 Lenovo.
