About this manual
Chapter 1. Safety information
Chapter 2. General checkout
- What to do first
- CRU list
Chapter 3. Idetifying FRUs (CRUs)
- Locate FRUs and CRUs
Chapter 4. Removing a FRU or CRU
Appendix A. Label locations
Trademarks

Lenovo 5 15ARH05H User Manual

Displayed below is the user manual for 5 15ARH05H by Lenovo which is a product in the Notebooks category. This manual has pages.

Related Manuals

Lenovo Lenovo Legion 5 15ACH6A Manual

Lenovo Lenovo Tab P11 5G Manual

Lenovo Lenovo Legion 5 Pro Manual

Hardware Maintenance Manual

Lenovo Legion 5 (15″, 05) and Lenovo Legion 5P (15″, 05)

First Edition (March 2020)

Contents

About this manual . . . . . . . . . . . . iii

Chapter 1. Safety information . . . . . . 1

General safety . . . . . . . . . . . . . . . . 1

Electrical safety . . . . . . . . . . . . . . . . 1

Safety inspection guide . . . . . . . . . . . . . 2

Handling devices that are sensitive to electrostatic

discharge . . . . . . . . . . . . . . . . . . 3

Grounding requirements . . . . . . . . . . . . 4

Safety notices (multilingual translations) . . . . . . 4

Chapter 2. General checkout . . . . . 21

What to do first . . . . . . . . . . . . . . . 21

CRU list . . . . . . . . . . . . . . . . . . 22

Chapter 3. Idetifying FRUs (CRUs) . . 23

Locate FRUs and CRUs . . . . . . . . . . . 23

Chapter 4. Removing a FRU or

CRU . . . . . . . . . . . . . . . . . . 31

Service tools . . . . . . . . . . . . . . . . 31

General guidelines. . . . . . . . . . . . . . 31

Removal procedure for Lenovo Legion 5 (15″,

05) . . . . . . . . . . . . . . . . . . . . 32

Remove the lower case . . . . . . . . . . 32

Remove the solid-state drive (SSD) plate . . . 33

Remove the solid-state drive (SSD) . . . . . 34

Remove the battery pack . . . . . . . . . 35

Remove the Wi-Fi card . . . . . . . . . . 35

Remove the hard disk drive (HDD) module . . 36

Remove the memory module . . . . . . . . 37

Remove the heat sink. . . . . . . . . . . 38

Remove the fan . . . . . . . . . . . . . 38

Remove the I/O board . . . . . . . . . . 39

Remove the Kensington lock . . . . . . . . 40

Remove the RTC battery . . . . . . . . . 41

Remove the speakers. . . . . . . . . . . 42

Remove the system board and the I/O board

cable . . . . . . . . . . . . . . . . . 42

Remove the strip cover . . . . . . . . . . 44

Remove the LCD module . . . . . . . . . 45

Remove the upper case (with keyboard and

touch pad) . . . . . . . . . . . . . . . 46

Disassemble the LCD module . . . . . . . 47

Removal procedure for Lenovo Legion 5P (15″,

05) . . . . . . . . . . . . . . . . . . . . 50

Remove the lower case . . . . . . . . . . 50

Remove the solid-state drive (SSD) plate . . . 51

Remove the solid-state drive (SSD) . . . . . 51

Remove the solid-state drive (SSD) stand

off . . . . . . . . . . . . . . . . . . 53

Remove the battery pack . . . . . . . . . 53

Remove the Wi-Fi card . . . . . . . . . . 54

Remove the hard disk drive (HDD) module . . 54

Remove the memory module . . . . . . . . 55

Remove the thermal module . . . . . . . . 56

Remove the I/O board . . . . . . . . . . 57

Remove the Kensington lock . . . . . . . . 58

Remove the RTC battery . . . . . . . . . 59

Remove the Microphone module . . . . . . 59

Remove the speakers. . . . . . . . . . . 60

Remove the system board and the I/O board

cable . . . . . . . . . . . . . . . . . 61

Remove the strip cover . . . . . . . . . . 63

Remove the LCD module . . . . . . . . . 64

Remove the upper case (with keyboard and

touchpad) . . . . . . . . . . . . . . . 65

Disassemble the LCD module . . . . . . . 66

Attach the keyboard bracket mylar . . . . . . . 69

Appendix A. Label locations. . . . . . 71

Trademarks . . . . . . . . . . . . . . . . lxxiii

ii Hardware Maintenance Manual

About this manual

This manual contains service and reference information for the following Lenovo products.

Machine Machine type (MT)

Lenovo Legion 5 15IMH05H 81Y6

Lenovo Legion 5 15IMH05 82AU

Lenovo Legion 5 15ARH05H 82B1

Lenovo Legion 5 15ARH05 82B5

Lenovo Legion 5P 15IMH05H 82AW

Lenovo Legion 5P 15IMH05 82AY

Lenovo Legion 5P 15ARH05H 82GU

Important:

• This manual is intended only for trained service technicians who are familiar with Lenovo products.

• Before servicing a Lenovo product, be sure to read all the information under Chapter 1 “Safety

information” on page 1.

iv Hardware Maintenance Manual

Chapter 1. Safety information

This chapter presents the following safety information that you need to be familiar with before you service a

Lenovo notebook computer.

General safety

Follow these rules to ensure general safety:

• Observe good housekeeping in the area of the machines during and after maintenance.

• When lifting any heavy object:

1. Make sure that you can stand safely without slipping.

2. Distribute the weight of the object equally between your feet.

3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift.

4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the

muscles in your back. Do not attempt to lift any object that weighs more than 16 kg (35 lb) or that you

think is too heavy for you.

• Do not perform any action that causes hazards to the customer, or that makes the equipment unsafe.

• Before you start the machine, make sure that other service technicians and the customer's personnel are

not in a hazardous position.

• Place removed covers and other parts in a safe place, away from all personnel, while you are servicing the

machine.

• Keep your tool case away from walk areas so that other people will not trip over it.

• Do not wear loose clothing that can be trapped in the moving parts of a machine. Make sure that your

sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it.

• Insert the ends of your necktie or scarf inside clothing or fasten it with a non-conductive clip, about 8

centimeters (3 inches) from the end.

• Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing.

Attention: Metal objects are good electrical conductors.

• Wear safety glasses when you are hammering, drilling, soldering, cutting wire, attaching springs, using

solvents, or working in any other conditions that might be hazardous to your eyes.

• After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that

is worn or defective.

• Reinstall all covers correctly before returning the machine to the customer.

• Fan louvers on the machine help to prevent overheating of internal components. Do not obstruct fan

louvers or cover them with labels or stickers.

Electrical safety

Observe the following rules when working on electrical equipment.

Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft

material that does not insulate you when working with live electrical currents.Many customers have, near

their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges.

Do not use this type of mat to protect yourself from electrical shock.

• Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet. If an electrical

accident occurs, you can then operate the switch or unplug the power cord quickly.

• Do not work alone under hazardous conditions or near equipment that has hazardous voltages.

• Disconnect all power before:

– Performing a mechanical inspection

– Working near power supplies

– Removing or installing main units

• Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer

to power-off the wall box that supplies power to the machine, and to lock the wall box in the off position.

• If you need to work on a machine that has exposed electrical circuits, observe the following precautions:

– Ensure that another person, familiar with the power-off controls, is near you.

Attention: Another person must be there to switch off the power, if necessary.

– Use only one hand when working with powered-on electrical equipment; keep the other hand in your

pocket or behind your back.

Attention: An electrical shock can occur only when there is a complete circuit. By observing the above

rule, you may prevent a current from passing through your body.

– When using testers, set the controls correctly and use the approved probe leads and accessories for

that tester.

– Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as

metal floor strips and machine frames.

Observe the special safety precautions when you work with very high voltages; Instructions for these

precautions are in the safety sections of maintenance information. Use extreme care when measuring high

voltages.

• Regularly inspect and maintain your electrical hand tools for safe operational condition.

• Do not use worn or broken tools and testers.

• Never assume that power has been disconnected from a circuit. First, check that it has been powered off.

• Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors,

non-grounded power extension cables, power surges, and missing safety grounds.

• Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is

conductive; such touching can cause personal injury and machine damage.

• Do not service the following parts with the power on when they are removed from their normal operating

places in a machine:

– Power supply units

– Pumps

– Blowers and fans

– Motor generators

– Similar units as listed above

This practice ensures correct grounding of the units.

• If an electrical accident occurs:

– Use caution; do not become a victim yourself.

– Switch off power.

– Send another person to get medical aid.

Safety inspection guide

The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each

machine was designed and built, required safety items were installed to protect users and service

technicians from injury. This guide addresses only those items. You should use good judgment to identify

potential safety hazards due to attachment of non-Lenovo features or options not covered by this inspection

guide.

If any unsafe conditions are present, you must determine how serious the apparent hazard could be and

whether you can continue without first correcting the problem.

Consider these conditions and the safety hazards they present:

• Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal

electrical shock)

• Explosive hazards, such as a damaged cathode ray tube (CRT) face or a bulging capacitor

• Mechanical hazards, such as loose or missing hardware

2Hardware Maintenance Manual

To determine whether there are any potentially unsafe conditions, use the following checklist at the

beginning of every service task. Begin the checks with the power off, and the power cord disconnected.

Checklist:

1. Check exterior covers for damage (loose, broken, or sharp edges).

2. Power off the computer. Disconnect the power cord.

3. Check the power cord for:

a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground

continuity for 0.1 ohm or less between the external ground pin and the frame ground.

b. The power cord should be the authorized type specified for your computer. Go to: http://

www.lenovo.com/serviceparts-lookup

c. Insulation must not be frayed or worn.

4. Check for cracked or bulging batteries.

5. Remove the cover.

6. Check for any obvious non-Lenovo alterations. Use good judgment as to the safety of any non-Lenovo

alterations.

7. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or

other liquids, or signs of fire or smoke damage.

8. Check for worn, frayed, or pinched cables.

9. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered

with.

Handling devices that are sensitive to electrostatic discharge

Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to

electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects.

Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the

person handling the part are all at the same charge.

Notes:

1. Use product-specific ESD procedures when they exceed the requirements noted here.

2. Make sure that the ESD protective devices you use have been certified (ISO 9000) as fully effective.

When handling ESD-sensitive parts:

• Keep the parts in protective packages until they are inserted into the product.

• Avoid contact with other people.

• Wear a grounded wrist strap against your skin to eliminate static on your body.

• Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when

you are wearing a wrist strap.

• Use a grounded work mat to provide a static-free work surface. The mat is especially useful when

handling ESD-sensitive devices.

• Select a grounding system, such as those listed below, to provide protection that meets the specific

service requirement.

Note: The use of a grounding system to guard against ESD damage is desirable but not necessary.

– Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground.

– When working on a double-insulated or battery-operated system, use an ESD common ground or

reference point. You can use coax or connector-outside shells on these systems.

– Use the round ground prong of the ac plug on ac-operated computers.

Chapter 1.Safety information 3

Grounding requirements

Electrical grounding of the computer is required for operator safety and correct system function. Proper

grounding of the electrical outlet can be verified by a certified electrician.

Safety notices (multilingual translations)

The safety notices in this section are provided in the following languages:

• English

• Arabic

• Brazilian Portuguese

• French

• German

• Hebrew

• Japanese

• Korean

• Spanish

• Traditional Chinese

DANGER

4Hardware Maintenance Manual

DANGER

Chapter 1.Safety information 5

6Hardware Maintenance Manual

PERIGO

Chapter 1.Safety information 7

PERIGO

8Hardware Maintenance Manual

DANGER

Chapter 1.Safety information 9

DANGER

VORSICHT

10 Hardware Maintenance Manual

VORSICHT

Chapter 1.Safety information 11

VORSICHT

12 Hardware Maintenance Manual

Chapter 1.Safety information 13

14 Hardware Maintenance Manual

Chapter 1.Safety information 15

16 Hardware Maintenance Manual

Chapter 1.Safety information 17

18 Hardware Maintenance Manual

Chapter 1.Safety information 19

20 Hardware Maintenance Manual

Chapter 2. General checkout

This chapter contains the following topics:

Before you go to the checkout instructions, ensure that you read the following important notes.

Important notes:

• Only certified trained personnel should service the computer.

• Before replacing any FRU, read the entire page on removing and replacing FRUs.

• Be extremely careful during such write operations as copying, saving, or formatting. Drives in the computer

that you are servicing sequence might have been altered. If you select an incorrect drive, data or programs might be

overwritten.

• Replace an FRU only with another FRU of the correct model. When you replace a FRU, make sure that the

model of the machine and the FRU part number are correct by referring to the FRU parts list.

• An FRU should not be replaced because of a single, unreproducible failure. Single failures can occur for a

variety of reasons that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge,

or software errors. Consider replacing an FRU only when a problem recurs. If you suspect that an FRU is defective,

clear the error log and run the test again. If the error does not recur, do not replace the FRU.

• Be careful not to replace a nondefective FRU.

What to do first

When you return an FRU, you must include the following information in the parts exchange form or parts

return form that you attach to it:

1. Name and phone number of service technician

2. Date of service

3. Date on which the machine failed

4. Date of purchase

5. Failure symptoms, error codes appearing on the display, and beep symptoms

6. Procedure index and page number in which the failing FRU was detected

7. Failing FRU name and part number

8. Machine type, model number, and serial number

9. Customer's name and address

Note: During the warranty period, the customer may be responsible for repair costs if the computer damage

was caused by misuse, accident, modification, unsuitable physical or operating environment, or improper

maintenance by the customer. Following is a list of some common items that are not covered under warranty

and some symptoms that might indicate that the system was subjected to stress beyond normal use.

Before checking problems with the computer, determine whether the damage is covered under the warranty

by referring to the following list:

The following are not covered under warranty:

• LCD panel cracked from the application of excessive force or from being dropped

• Scratched (cosmetic) parts

• Distortion, deformation, or discoloration of the cosmetic parts

• Plastic parts, latches, pins, or connectors that have been cracked or broken by excessive force

• Damage caused by liquid spilled into the system

• Damage caused by the improper insertion of a personal-computer card (PC card) or the installation of an

incompatible card

• Improper disc insertion or use of an external optical drive

• Fuses blown by attachment of a non-supported device

• Forgotten computer password (making the computer unusable)

• Sticky keys caused by spilling a liquid onto the keyboard

• Use of an incorrect ac power adapter on laptop products

The following symptoms might indicate damage caused by non-warranted activities:

• Missing parts might be a symptom of unauthorized service or modification.

• Check for obvious damage to a hard disk drive. If the spindle of a hard disk drive becomes noisy, the hard

disk drive might have been dropped or subject to excessive force.

CRU list

Table 1. Model: all

CRU Type

ac power adapter self-service

Power cord self-service

Mouse self-service

22 Hardware Maintenance Manual

Chapter 3. Idetifying FRUs (CRUs)

Locate FRUs and CRUs

The exploded illustrations help Lenovo service technicians identify FRUs or CRUs that they may need to

replace when servicing a customer’s computer.

Figure 1. Lenovo Legion 5 (15″, 05) exploded view

24 Hardware Maintenance Manual

Table 2. FRU (CRU) categories

No. FRU (CRU) category

1Strip cover

2Upper case (with keyboard and touchpad)

3System board

4Keyboard bracket mylar

Note: Attach the keyboard bracket mylar after replacing the related FRU.

5I/O board cable

6I/O board

7Kensington Lock

8RTC battery

9Hard disk drive (HDD) cable

10 Hard disk drive (HDD)

11 Hard disk drive (HDD) bracket

12 Heat sink

13 Fan

14 Speakers

15 Battery pack

16 Lower case

17 Battery gasket

18 Solid-state drive (SSD) plate

19 Solid-state drive (SSD) bracket

Note: The SSD bracket is used to lock the screw for the 2242 SSD.

20 Solid-state drive (SSD)

21 Wi-Fi card

22 Memory shielding

23 Memory

aPower cord

bac power adapter

cScrew kit

Chapter 3.Idetifying FRUs (CRUs) 25

Figure 2. Lenovo Legion 5 (15″, 05) LCD module - exploded view

Table 3. FRU categories for the LCD module

No. FRU (CRU) category

1LCD cover

2Adhesive tapes

3LCD panel

4Camera

5Microphone rubber

6LCD bezel

26 Hardware Maintenance Manual

Figure 3. Lenovo Legion 5P (15″, 05) exploded view

Chapter 3.Idetifying FRUs (CRUs) 27

Table 4. FRU (CRU) categories

No. FRU (CRU) category

1Strip cover

2Upper case (with keyboard and touch pad)

3System board

4Keyboard bracket mylar

Note: Attach the keyboard bracket mylar after replacing the related FRU.

5I/O board cable

6I/O board

7Kensington Lock

8RTC battery

9Hard disk drive (HDD) cable

10 Hard disk drive (HDD)

11 Hard disk drive (HDD) bracket

12 Microphone board cable

13 Microphone rubber

14 Microphone board

15 Thermal module

16 Speakers

17 Battery pack

18 Lower case

19 Battery gasket

20 Solid-state drive (SSD) plate

21 Solid-state drive (SSD) bracket

Note: The SSD bracket is used to lock the screw for the 2242 SSD.

22 Solid-state drive (SSD)

23 SSD stand off

24 Wi-Fi card

25 Memory shielding

26 Memory

aPower cord

bac power adapter

cScrew kit

28 Hardware Maintenance Manual

Figure 4. Lenovo Legion 5P (15″, 05) LCD module — exploded view

Table 5. FRU categories for the LCD module

No. FRU (CRU) category

1LCD cover

2Adhesive tapes

3LCD panel

4LCD bezel

Chapter 3.Idetifying FRUs (CRUs) 29

30 Hardware Maintenance Manual

Chapter 4. Removing a FRU or CRU

Service tools

The following table lists tools for servicing Lenovo computers. Tools with a cross mark are needed for serving

the product models as described by this publication. Prepare them before you service the product.

Table 6. Service tools

Service tool and consumable Model applicability

Screw driver (Phillips head) (PH1/PH0) X

Screw driver (Torx head) (T5)

Screw driver (Torx head) (T30)

Pry tool 1 X

Tweezers (conductive) X

Tweezers (isolated)

Suction cup

Hexagonal socket

Silicone grease

Acetate tape X

Polyamide tape

Mylar tape

Electrical tape

Double-sided tape

Conductive tape

Eraser

Heat gun

Brown brush

Notes:

• T30 screw drivers are used to service the new Intel Xeon CPUs.

• Hexagonal sockets are used to remove antenna connectors.

• Silicone grease is applied to the CPU and heatsink surfaces to eliminate air gaps.

General guidelines

When removing or replacing an FRU, ensure that you observe the following general guidelines:

1. Do not try to service any computer unless you have been trained and certified. An untrained person runs

the risk of damaging parts.

2. Begin by removing any FRUs that have to be removed before replacing the failing FRU. Any such FRUs

are listed at the beginning of each FRU replacement procedure. Remove them in the order in which they

are listed.

3. Follow the correct sequence in the steps for removing an FRU, as shown in the illustrations by the

numbers in square callouts.

4. When removing an FRU, move it in the direction as shown by the arrow in the illustration.

5. To install a new FRU in place, perform the removal procedure in reverse and follow any notes that

pertain to replacement.

6. When replacing an FRU, carefully retain and reuse all screws.

7. When replacing the base cover, reapply all labels that come with the replacement base cover. If some

original labels are not included with the replacement base cover, peel them off from the original base

cover and paste them on the replacement base cover.

DANGER

Before removing any FRU or CRU, shut down the computer and unplug all power cords from

electrical outlets.

Attention: After replacing an FRU, do not turn on the computer until you have ensured that all screws,

springs, and other small parts are in place and none are loose inside the computer. Verify this by shaking the

computer gently and listening for rattling sounds. Metallic parts or metal flakes can cause electrical short

circuits.

Attention: The system board is sensitive to and can be damaged by ESD. Before touching it, establish

personal grounding by touching a ground point with one hand or by using an ESD strap (P/N 6405959).

Removal procedure for Lenovo Legion 5 (15″, 05)

Remove the lower case

Make sure the computer has been shut down before servicing the computer.

Step 1. Place the computer upside down on a flat surface.

Step 2. Remove eleven screws.

Figure 5. Remove eleven screws

32 Hardware Maintenance Manual

Screw specifications Number of screws

M2 x L8 7

M2 x L4 4

Step 3. Pry up the latches and then remove the lower case.

Figure 6. Pry up the latches and remove the lower case

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

Lower case

Remove the solid-state drive (SSD) plate

Make sure the following FRU (or CRU) has been removed.

“Remove the lower case” on page 32

Step 1. Disconnect the battery cable from the system board.

Attention: Use your fingernails to pull the connector to unplug it. Do not pull the cable.

Figure 7. Disconnect the battery cable from the system board

Step 2. Remove three screws and then remove the SSD plate carefully.

Chapter 4.Removing a FRU or CRU 33

Note: If your computer includes two SSD drives, there are two SSD plates.

Figure 8. Remove the SSD plate

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

SSD plate

Remove the solid-state drive (SSD)

Make sure the following FRUs (or CRUs) have been removed.

“Remove the lower case” on page 32

“Remove the solid-state drive (SSD) plate” on page 33

Step 1. Remove one screw and then remove the SSD by pulling it away from the slot.

Figure 9. Remove the SSD

Screw specifications Number of screws

M2 x L3 1

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

SSD

34 Hardware Maintenance Manual

Remove the battery pack

Make sure the following FRUs (or CRUs) have been removed.

“Remove the lower case” on page 32

“Remove the solid-state drive (SSD)” on page 34

Step 1. Remove four screws and then remove the battery pack.

Note: Attach the battery gasket to the battery pack when replacing the battery pack.

Figure 10. Remove the battery pack

Screw specifications Number of screws

M2 x L4.5 4

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

Battery pack

Remove the Wi-Fi card

Make sure the following FRUs (or CRUs) have been removed.

“Remove the lower case” on page 32

“Remove the solid-state drive (SSD) plate” on page 33

Step 1. Detach the main and auxiliary antenna cable connectors. Remove one screw and then remove the

Wi-Fi card by pulling it away from the slot.

Chapter 4.Removing a FRU or CRU 35

Figure 11. Remove the Wi-Fi card

Screw specifications Number of screws

M2 x L3 1

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

Wi-Fi card

Remove the hard disk drive (HDD) module

Make sure the following FRUs (or CRUs) have been removed.

“Remove the lower case” on page 32

“Remove the battery pack” on page 35

Step 1. Disconnect the HDD cable from the system board. Remove three screws and then remove the HDD

module.

Figure 12. Remove the HDD module

Screw specifications Number of screws

M2 x L4.5 3

Step 2. Remove the HDD cable. Then remove four screws and separate the HDD and the HDD bracket.

36 Hardware Maintenance Manual

Figure 13. Separate the HDD cable, HDD and the HDD bracket

Screw specifications Number of screws

M3 x L3 4

Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following

replacement parts:

HDD

HDD cable

HDD bracket

Remove the memory module

Make sure the following FRU (or CRU) has been removed.

“Remove the lower case” on page 32

Step 1. Disconnect the battery pack cable from the system board.

Attention: Use your fingernails to pull the connector to unplug it. Do not pull the cable.

Step 2. Remove the memory shielding.

Figure 14. Remove the memory shielding

Step 3. Open the buckles and then remove the memory.

Chapter 4.Removing a FRU or CRU 37

Figure 15. Remove the memory

Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following

replacement parts:

Memory

Memory shielding

Remove the heat sink

Make sure the following FRU (or CRU) has been removed.

“Remove the lower case” on page 32

Step 1. Disconnect the battery pack cable from the system board.

Attention: Use your fingernails to pull the connector to unplug it. Do not pull the cable.

Step 2. Loosen six screws and then remove the heat sink.

Figure 16. Loosen six screws and remove the heat sink

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

Heat sink

Remove the fan

Make sure the following FRUs (or CRUs) have been removed.

“Remove the lower case” on page 32

38 Hardware Maintenance Manual

“Remove the solid-state drive (SSD) plate” on page 33

Step 1. Disconnect the fan cables from the system board.

Figure 17. Disconnect the fan cables from the system board

Step 2. Remove five screws and then remove the fan.

Figure 18. Remove five screws and remove the fan

Screw specifications Number of screws

M2 x L4.5 5

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

Fan

Remove the I/O board

Make sure the following FRU (or CRU) has been removed.

“Remove the lower case” on page 32

Step 1. Disconnect the battery pack cable from the system board.

Chapter 4.Removing a FRU or CRU 39

Attention: Use your fingernails to pull the connector to unplug it. Do not pull the cable.

Step 2. Detach the fan cable and remove three screws. Remove the fan as show.

Figure 19. Remove the fan

Screw specifications Number of screws

M2 x L4.5 3

Step 3. Detach the I/O board cable and remove one screw. Remove the I/O board.

Figure 20. Remove the I/O board

Screw specifications Number of screws

M2 x L3.5 1

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

I/O board

Remove the Kensington lock

Make sure the following FRU (or CRU) has been removed.

“Remove the lower case” on page 32

40 Hardware Maintenance Manual

Step 1. Disconnect the battery pack cable from the system board.

Attention: Use your fingernails to pull the connector to unplug it. Do not pull the cable.

Step 2. Remove two screws and then remove the Kensington lock.

Figure 21. Remove the Kensington lock

Screw specifications Number of screws

M2 x L7 2

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

Kensington lock

Remove the RTC battery

Make sure the following FRUs (or CRUs) have been removed.

“Remove the lower case” on page 32

“Remove the battery pack” on page 35

Step 1. Disconnect the touch pad cable and the RTC battery cable from the system board. Remove the

RTC battery.

Figure 22. Remove the RTC battery

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

RTC battery

Chapter 4.Removing a FRU or CRU 41

Remove the speakers

Make sure the following FRUs (CRUs) have been removed.

“Remove the lower case” on page 32

“Remove the battery pack” on page 35

“Remove the hard disk drive (HDD) module” on page 36

Step 1. Detach the antenna cable connectors and disconnect the keyboard cable from the system board.

Figure 23. Detach the cables

Step 2. Disconnect the speaker cable from the system board and then remove the speakers.

Figure 24. Remove the speakers

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

Speakers

Remove the system board and the I/O board cable

Make sure the following FRUs (or CRUs) have been removed.

“Remove the lower case” on page 32

“Remove the solid-state drive (SSD)” on page 34

“Remove the battery pack” on page 35

“Remove the heat sink” on page 38

“Remove the fan” on page 38

42 Hardware Maintenance Manual

“Remove the Kensington lock” on page 40

Step 1. Disconnect cables connected to the system board.

Figure 25. Disconnect cables

Step 2. Disconnect the speaker cable from the system board.

Figure 26. Disconnect the speaker cable from the system board

Step 3. Remove six screws and then lift the system board.

Chapter 4.Removing a FRU or CRU 43

Figure 27. Remove six screws and lift the system board

Step 4. Turn over the system board. Disconnect the touch pad cable from the system board and then

remove the system board.

Figure 28. Remove the system board

Step 5. Remove the I/O board cable.

Figure 29. Remove the I/O board cable

Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following

replacement parts:

System board

I/O board cable

Remove the strip cover

Make sure the following FRU (CRU) has been removed.

44 Hardware Maintenance Manual

“Remove the lower case” on page 32

Step 1. Disconnect the battery cable from the system board.

Attention: Use your fingernails to pull the connector to unplug it. Do not pull the cable.

Step 2. Remove five screws.

Figure 30. Remove five screws

Step 3. Turn over the computer and then remove the strip cover.

Figure 31. Remove the strip cover

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

Strip cover

Remove the LCD module

Make sure the following FRUs (CRUs) have been removed.

“Remove the lower case” on page 32

“Remove the heat sink” on page 38

“Remove the fan” on page 38

“Remove the strip cover” on page 44

Step 1. Disconnect the EDP cable from the system board and then remove four screws.

Chapter 4.Removing a FRU or CRU 45

Figure 32. Disconnect the EDP cable from the system board and remove four screws

Step 2. Turn over the computer and remove six screws. Lift the LCD module carefully.

Figure 33. Remove six screws and lift the LCD module

Step 3. Detach the EDP cable and then remove the LCD module.

Figure 34. Remove the LCD module

Remove the upper case (with keyboard and touch pad)

Make sure the following FRUs (CRUs) have been removed.

“Remove the lower case” on page 32

46 Hardware Maintenance Manual

“Remove the solid-state drive (SSD) plate” on page 33

“Remove the solid-state drive (SSD)” on page 34

“Remove the battery pack” on page 35

“Remove the Wi-Fi card” on page 35

“Remove the hard disk drive (HDD) module” on page 36

“Remove the memory module” on page 37

“Remove the heat sink” on page 38

“Remove the fan” on page 38

“Remove the I/O board” on page 39

“Remove the Kensington lock” on page 40

“Remove the RTC battery” on page 41

“Remove the speakers” on page 42

“Remove the system board and the I/O board cable” on page 42

“Remove the strip cover” on page 44

“Remove the LCD module” on page 45

Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following

replacement part:

Upper case (with keyboard and touch pad)

Disassemble the LCD module

The LCD module as a whole is not an FRU. Instead, it contains FRUs as its components. Before

disassembling the LCD module, make sure it has been detached from the upper case.

Remove the LCD bezel

Make sure the following FRU (CRU) has been removed.

“Remove the LCD module” on page 45

Step 1. Remove the LCD bezel.

Figure 35. Remove the LCD bezel

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

LCD bezel

Chapter 4.Removing a FRU or CRU 47

Remove the LCD panel

Make sure the following FRU (CRU) has been removed.

“Remove the LCD bezel” on page 47

Step 1. Carefully pull out the pieces of adhesive tape with tweezers.

Figure 36. Pull out the pieces of adhesive tape with tweezers

Step 2. Lift the LCD panel carefully and then detach the EDP cable.

Figure 37. Remove the LCD panel

Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following

replacement parts:

Adhesive tape

LCD panel

48 Hardware Maintenance Manual

Remove the camera and the microphone rubber

Make sure the following FRU (CRU) has been removed.

“Remove the LCD panel” on page 48

Step 1. Disconnect the EDP cable from the camera and then remove the camera.

Figure 38. Remove the camera

Step 2. Remove the microphone rubber.

Figure 39. Remove the microphone rubber

Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following

replacement parts:

Camera

Microphone rubber

Remove the LCD cover

Make sure the following FRUs (CRUs) have been removed.

“Remove the LCD module” on page 45

“Remove the LCD bezel” on page 47

“Remove the LCD panel” on page 48

“Remove the camera and the microphone rubber” on page 49

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

LCD cover

Chapter 4.Removing a FRU or CRU 49

Removal procedure for Lenovo Legion 5P (15″, 05)

Remove the lower case

Make sure the computer has been shut down before servicing the computer.

Step 1. Place the computer upside down on a flat surface.

Step 2. Remove eleven screws.

Figure 40. Remove eleven screws

Screw specifications Number of screws

M2 x L8 7

M2 x L4 4

Step 3. Pry up the latches and then remove the lower case.

Figure 41. Pry up the latches and remove the lower case

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

Lower case

50 Hardware Maintenance Manual

Remove the solid-state drive (SSD) plate

Make sure the following FRU (or CRU) has been removed.

“Remove the lower case” on page 50

Step 1. Disconnect the battery cable from the system board.

Attention: Use your fingernails to pull the connector to unplug it. Do not pull the cable.

Figure 42. Disconnect the battery cable from the system board

Step 2. Remove three screws and then remove the SSD plate carefully.

Note: If your computer includes two SSD drives, there are two SSD plates.

Figure 43. Remove the SSD plate

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

SSD plate

Remove the solid-state drive (SSD)

Make sure the following FRUs (or CRUs) have been removed.

“Remove the lower case” on page 50

“Remove the solid-state drive (SSD) plate” on page 51

Step 1. Remove one screw and then remove the SSD by pulling it away from the slot.

Chapter 4.Removing a FRU or CRU 51

Figure 44. Remove the SSD

Screw specifications Number of screws

M2 x L3 1

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

SSD

Calibrate panel colors after an SSD/HDD replacement

This post-operation is only applicable to computer models with an FCC (factory color calibration) panel.

Catalog name MT FCC panel?

Lenovo Legion 5 15IMH05H 81Y6 No

Lenovo Legion 5 15IMH05 82AU No

Lenovo Legion 5 15ARH05H 82B1 No

Lenovo Legion 5 15ARH05 82B5 No

Lenovo Legion 5P 15IMH05H 82AW Yes

Lenovo Legion 5P 15IMH05 82AY Yes

Lenovo Legion 5P 15ARH05H 82GU Yes

For computer models with an FCC panel, the panel is color calibrated at factory and a file containing all the

color settings is installed on the computer’s secondary storage device. After an SSD/HDD replacement,

instruct users to follow the steps below to re-install the factory color profile for the display panel.

Step 1. Make sure the computer is connected to the Internet.

Step 2. Open the pre-installed X-Rite Color Assistant app.

Note: If the app is un-installed, re-install it by downloading the installation package from https://

pcsupport.lenovo.com/us/en/downloads/DS543953.

Step 3. Go to Settings and select Restore profiles under Restore profiles from Lenovo cloud.The app

will read the SN of the computer and download its unique color profile from Lenovo cloud.

52 Hardware Maintenance Manual

Remove the solid-state drive (SSD) stand off

Make sure the following FRUs (or CRUs) have been removed.

“Remove the lower case” on page 50

“Remove the solid-state drive (SSD)” on page 51

Step 1. Remove the SSD stand off (for 2242 SSD only).

Figure 45. Remove the SSD stand off (for 2242 SSD only)

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

SSD stand off

Remove the battery pack

Make sure the following FRUs (or CRUs) have been removed.

“Remove the lower case” on page 50

“Remove the solid-state drive (SSD) plate” on page 51

Step 1. Remove four screws and then remove the battery pack.

Note: Attach the battery gasket to the battery pack when replacing the battery pack.

Figure 46. Remove the battery pack

Screw specifications Number of screws

M2 x L4.5 4

Chapter 4.Removing a FRU or CRU 53

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

Battery pack

Remove the Wi-Fi card

Make sure the following FRUs (or CRUs) have been removed.

“Remove the lower case” on page 50

“Remove the solid-state drive (SSD) plate” on page 51

Step 1. Detach the main and auxiliary antenna cable connectors. Remove one screw and then remove the

Wi-Fi card by pulling it away from the slot.

Figure 47. Remove the Wi-Fi card

Screw specifications Number of screws

M2 x L3 1

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

Wi-Fi card

Remove the hard disk drive (HDD) module

Make sure the following FRUs (or CRUs) have been removed.

“Remove the lower case” on page 50

“Remove the battery pack” on page 53

Step 1. Disconnect the HDD cable from the system board. Remove three screws and then remove the HDD

module.

54 Hardware Maintenance Manual

Figure 48. Remove the HDD module

Screw specifications Number of screws

M2 x L4.5 3

Step 2. Remove the HDD cable. Then remove four screws and separate the HDD and the HDD bracket.

Figure 49. Separate the HDD cable, HDD and the HDD bracket

Screw specifications Number of screws

M3 x L3 4

Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following

replacement parts:

HDD

HDD cable

HDD bracket

Remove the memory module

Make sure the following FRU (or CRU) has been removed.

“Remove the lower case” on page 50

Step 1. Disconnect the battery pack cable from the system board.

Attention: Use your fingernails to pull the connector to unplug it. Do not pull the cable.

Step 2. Remove the memory shielding.

Chapter 4.Removing a FRU or CRU 55

Figure 50. Remove the memory shielding

Step 3. Open the buckles and then remove the memory.

Figure 51. Remove the memory

Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following

replacement parts:

Memory

Memory shielding

Remove the thermal module

Make sure the following FRUs (or CRUs) have been removed.

“Remove the lower case” on page 50

“Remove the solid-state drive (SSD) plate” on page 51

Step 1. Disconnect the module cables from the system board.

56 Hardware Maintenance Manual

Figure 52. Loosen six screws and remove the heat sink

Step 2. Loosen six screws and remove five screws. Remove the thermal module.

Figure 53. Remove the thermal module

Screw specifications Number of screws

M2 x L4.5 5

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

Thermal module

Remove the I/O board

Make sure the following FRUs (or CRUs) have been removed.

“Remove the lower case” on page 50

“Remove the thermal module” on page 56

Step 1. Detach the I/O board cable and remove one screw. Remove the I/O board.

Chapter 4.Removing a FRU or CRU 57

Figure 54. Remove the I/O board

Screw specifications Number of screws

M2 x L3.5 1

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

I/O board

Remove the Kensington lock

Make sure the following FRU (or CRU) has been removed.

“Remove the lower case” on page 50

Step 1. Disconnect the battery pack cable from the system board.

Attention: Use your fingernails to pull the connector to unplug it. Do not pull the cable.

Step 2. Remove two screws and then remove the Kensington lock.

Figure 55. Remove the Kensington lock

Screw specifications Number of screws

M2 x L7 2

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

58 Hardware Maintenance Manual

Kensington lock

Remove the RTC battery

Make sure the following FRUs (or CRUs) have been removed.

“Remove the lower case” on page 50

“Remove the battery pack” on page 53

Step 1. Disconnect the touch pad cable and the RTC battery cable from the system board. Remove the

RTC battery.

Figure 56. Remove the RTC battery

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

RTC battery

Remove the Microphone module

Make sure the following FRUs (or CRUs) have been removed.

“Remove the lower case” on page 50

“Remove the battery pack” on page 53

“Remove the hard disk drive (HDD) module” on page 54

Step 1. Disconnect the microphone board cable from the system board and then remove the microphone

board.

Figure 57. Remove the microphone board

Chapter 4.Removing a FRU or CRU 59

Step 2. Remove the microphone board cable.

Figure 58. Remove the microphone board cable

Step 3. Turn over the microphone board and then remove the microphone rubber.

Figure 59. Remove the microphone rubber

Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following

replacement parts:

Microphone board

Microphone Rubber

Microphone board cable

Remove the speakers

Make sure the following FRUs (CRUs) have been removed.

“Remove the lower case” on page 50

“Remove the battery pack” on page 53

“Remove the hard disk drive (HDD) module” on page 54

Step 1. Detach the antenna cable connectors and disconnect the keyboard cable from the system board.

Figure 60. Detach the cables

60 Hardware Maintenance Manual

Step 2. Disconnect the speaker cable from the system board and then remove the speakers.

Figure 61. Remove the speakers

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

Speakers

Remove the system board and the I/O board cable

Make sure the following FRUs (or CRUs) have been removed.

“Remove the lower case” on page 50

“Remove the solid-state drive (SSD)” on page 51

“Remove the battery pack” on page 53

“Remove the thermal module” on page 56

“Remove the Kensington lock” on page 58

Step 1. Disconnect cables connected to the system board.

Figure 62. Disconnect cables

Chapter 4.Removing a FRU or CRU 61

Step 2. Disconnect the speaker cable from the system board.

Figure 63. Disconnect the speaker cable from the system board

Step 3. Remove six screws and then lift the system board.

Figure 64. Remove six screws and lift the system board

Step 4. Turn over the system board. Disconnect the touch pad cable from the system board and then

remove the system board.

Figure 65. Remove the system board

Step 5. Remove the I/O board cable.

62 Hardware Maintenance Manual

Figure 66. Remove the I/O board cable

Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following

replacement parts:

System board

I/O board cable

Remove the strip cover

Make sure the following FRU (CRU) has been removed.

“Remove the lower case” on page 50

Step 1. Disconnect the battery cable from the system board.

Attention: Use your fingernail to pull the connector to unplug it. Do not pull the cable.

Step 2. Remove five screws.

Figure 67. Remove five screws

Step 3. Turn over the computer and then remove the strip cover.

Chapter 4.Removing a FRU or CRU 63

Figure 68. Remove the strip cover

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

Strip cover

Remove the LCD module

Make sure the following FRUs (CRUs) have been removed.

“Remove the lower case” on page 50

“Remove the thermal module” on page 56

“Remove the strip cover” on page 63

Step 1. Disconnect the EDP cable from the system board and then remove four screws.

Figure 69. Remove four screws

Step 2. Turn over the computer and remove six screws. Lift the LCD module carefully.

64 Hardware Maintenance Manual

Figure 70. Remove six screws and lift the LCD module

Step 3. Detach the EDP cable and then remove the LCD module.

Figure 71. Remove the LCD module

Remove the upper case (with keyboard and touchpad)

Make sure the following FRUs (CRUs) have been removed.

“Remove the lower case” on page 50

“Remove the solid-state drive (SSD) plate” on page 51

“Remove the solid-state drive (SSD)” on page 51

“Remove the battery pack” on page 53

“Remove the Wi-Fi card” on page 54

“Remove the hard disk drive (HDD) module” on page 54

“Remove the memory module” on page 55

“Remove the thermal module” on page 56

“Remove the I/O board” on page 57

“Remove the Kensington lock” on page 58

“Remove the RTC battery” on page 59

“Remove the Microphone module” on page 59

“Remove the speakers” on page 60

“Remove the system board and the I/O board cable” on page 61

Chapter 4.Removing a FRU or CRU 65

“Remove the strip cover” on page 63

“Remove the LCD module” on page 64

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

Upper case (with keyboard and touchpad)

Disassemble the LCD module

The LCD module as a whole is not an FRU. Instead, it contains FRUs as its components. Before

disassembling the LCD module, make sure it has been detached from the upper case.

Remove the LCD bezel

Make sure the following FRU (CRU) has been removed.

“Remove the LCD module” on page 64

Step 1. Remove the LCD bezel.

Note: The LCD bezel is not reusable.

Figure 72. Remove the LCD bezel

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

LCD bezel

Remove the LCD panel

Make sure the following FRUs (CRUs) have been removed.

“Remove the LCD module” on page 64

“Remove the LCD bezel” on page 66

Step 1. Carefully pull out the pieces of adhesive tape with tweezers.

66 Hardware Maintenance Manual

Figure 73. Pull out the pieces of adhesive tape with tweezers

Step 2. Lift the LCD panel carefully and detach the EDP cable.

Figure 74. Remove the LCD panel

Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following

replacement parts:

Adhesive tape

LCD panel

Calibrate colors after a panel replacement

This post-operation is only applicable to computer models with an FCC (factory color calibration) panel.

Catalog name MT FCC panel?

Lenovo Legion 5 15IMH05H 81Y6 No

Lenovo Legion 5 15IMH05 82AU No

Lenovo Legion 5 15ARH05H 82B1 No

Lenovo Legion 5 15ARH05 82B5 No

Chapter 4.Removing a FRU or CRU 67

Catalog name MT FCC panel?

Lenovo Legion 5P 15IMH05H 82AW Yes

Lenovo Legion 5P 15IMH05 82AY Yes

Lenovo Legion 5P 15ARH05H 82GU Yes

FCC panels are color calibrated at factory and a unique file containing all the color settings is generated and

stored on Lenovo cloud. After installing an FCC panel, follow the steps below to download and install the

color profile that is unique to the newly installed display panel.

Step 1. Make sure the X-Rite Color Assistant app is closed and the computer is connected to the Internet.

Step 2. Go to the C:\Program files(x86)\X-Rite Color Assistant folder and double-click

ProfileUpdaterForDisplayReplacement.exe.

Note: If you cannot find the specified folder or file, X-Rite Color Assistant may be uninstalled. You

need to re-install the app by downloading the installation package from https://

pcsupport.lenovo.com/us/en/downloads/DS543953.

Step 3. Follow on-screen instructions to enter the serial number (SN) for the newly installed panel

(replacement) and select Submit. Color profile that is unique to the replacement panel will be

downloaded automatically to the computer. A window is displayed when the profile is installed

successfully.

Note: The SN for the replacement panel can be found on a printed instruction as a part of the

panel FRU.

Remove the LCD cover

Make sure the following FRUs (CRUs) have been removed.

“Remove the LCD module” on page 64

“Remove the LCD bezel” on page 66

“Remove the LCD panel” on page 66

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement

part:

LCD cover

68 Hardware Maintenance Manual

Attach the keyboard bracket mylar

Step 1. Peel off the release paper according to direction guidance carefully.

Figure 75. Peel off the release paper

Step 2. Hold the keyboard bracket mylar and put the triangle indication hole to the nut of the upper case.

Attach the keyboard bracket mylar to the upper case.

Figure 76. Attach the keyboard bracket mylar

Chapter 4.Removing a FRU or CRU 69

70 Hardware Maintenance Manual

Appendix A. Label locations

Figure 77. Label layout on the back side of the base cover

Labels attached to the base cover are country/region specific. Make sure to apply the appropriate labels to

the replacement base cover.

Table 7. All base cover labels

Label Label name Applied country/region Label dimensions

aRating label P.R.China 66 mm x 24 mm

India 66 mm x 24 mm

Worldwide 66 mm x 24 mm

bPrint rating label P.R.China & India & Worldwide 43 mm x 24 mm

cOS label All 16 mm x 22.5 mm

dAdapter label Argentina 65 mm x 20 mm

eCountry label KCC label 50 mm x 16 mm

fTW label 70 mm x 10 mm

gArgentina label 68 mm x 6 mm

hIndonesia label 32 mm x 10 mm

IBIS label 22 mm x 30 mm

jWL/BT label All 35 mm x 15 mm

72 Hardware Maintenance Manual

Trademarks

LENOVO and the LENOVO logo are trademarks of Lenovo.

Table of Contents

Lenovo 5 15ARH05H User Manual

Related Manuals

Lenovo Lenovo Legion 5 15ACH6A Manual

Lenovo Lenovo Tab P11 5G Manual

Lenovo Lenovo Legion 5 Pro Manual

Lenovo Lenovo Legion 5 Pro Manual

Lenovo Lenovo Legion 5 Pro Manual

Lenovo Lenovo Legion 5 Pro Manual

Lenovo Lenovo Legion 5 Pro Manual