Table of Contents
- Chapter 1. Overview
- Chapter 2. Specifications
- Chapter 3. Computer locks
- Chapter 4. Replacing hardware
- Before replacing hardware
- Knowing FRUs (including CRUs)
- Locating FRUs (including CRUs)
- Replacing the keyboard or wireless keyboard
- Replacing the mouse or wireless mouse
- Replacing the power adapter
- Replacing the vertical stand
- Replacing the VESA mount bracket
- Replacing the power adapter bracket
- Removing the computer cover
- Replacing the storage drive for 10TF, 10TG, 10TH, 10TJ, and 10TK models
- Replacing the storage drive cable for 10TF, 10TG, 10TH, 10TJ, and 10TK models
- Replacing the system fan for 10TF, 10TG, 10TH, 10TJ, and 10TK models
- Replacing the heat sink
- Replacing the internal speaker
- Replacing the Wi-Fi card
- Replacing the Wi-Fi antennas
- Replacing the antenna bracket
- Replacing the coin-cell battery
- Replacing the bottom cover
- Replacing the memory module
- Replacing the M.2 storage drive
- Replacing the system board and chassis
- Completing the parts replacement
- Appendix A. Notices
- Appendix B. Trademarks
Lenovo M625q User Manual
Displayed below is the user manual for M625q by Lenovo which is a product in the Thin Clients category. This manual has pages.
Related Manuals
M625q User Guide and Hardware
Maintenance Manual
Enery Star Machine Types: 10TF, 10TG, 10TH, 10TJ, 10TK, 10TL,
10UY, 10V0, 10V1, and 10V2
Note: Before using this information and the product it supports, be sure to read and understand the
Important Product Information Guide and Appendix A “Notices” on page 67.
Second Edition (August 2019)
© Copyright Lenovo 2018, 2019.
LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant to a General Services
Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-
35F-05925.
Contents
Chapter 1. Overview . . . . . . . . . . . 1
Front view . . . . . . . . . . . . . . . . . . 1
Rear view . . . . . . . . . . . . . . . . . . 2
System board . . . . . . . . . . . . . . . . 4
Machine type and model label . . . . . . . . . . 6
Chapter 2. Specifications . . . . . . . . 7
Chapter 3. Computer locks . . . . . . . 9
Attaching a Kensington-style cable lock . . . . . . 9
Chapter 4. Replacing hardware . . . . 11
Before replacing hardware . . . . . . . . . . 11
Knowing FRUs (including CRUs) . . . . . . . . 11
Locating FRUs (including CRUs) . . . . . . . . 13
Replacing the keyboard or wireless keyboard . . . 16
Replacing the mouse or wireless mouse . . . . . 17
Replacing the power adapter . . . . . . . . . 21
Replacing the vertical stand . . . . . . . . . . 24
Replacing the VESA mount bracket . . . . . . . 25
Replacing the power adapter bracket . . . . . . 26
Removing the computer cover . . . . . . . . . 28
Replacing the storage drive for 10TF, 10TG, 10TH, 10TJ,
and 10TK models . . . . . . . . . . . . . . 30
Replacing the storage drive cable for 10TF, 10TG,
10TH, 10TJ, and 10TK models . . . . . . . . . 33
Replacing the system fan for 10TF, 10TG, 10TH,
10TJ, and 10TK models. . . . . . . . . . . . 34
Replacing the heat sink . . . . . . . . . . . . 36
Replacing the internal speaker . . . . . . . . . 39
Replacing the Wi-Fi card . . . . . . . . . . . 40
Replacing the Wi-Fi antennas . . . . . . . . . 45
Replacing the antenna bracket . . . . . . . . . 50
Replacing the coin-cell battery . . . . . . . . . 54
Replacing the bottom cover . . . . . . . . . . 56
Replacing the memory module . . . . . . . . . 58
Replacing the M.2 storage drive . . . . . . . . 59
Replacing the system board and chassis . . . . . 61
Completing the parts replacement . . . . . . . 64
Appendix A. Notices . . . . . . . . . . 67
Appendix B. Trademarks . . . . . . . 69
© Copyright Lenovo 2018, 2019 i
ii M625q User Guide and Hardware Maintenance Manual
Chapter 1. Overview
This chapter provides basic information to help you get familiar with your computer.
Front view
Note: Your computer model might look slightly different from the illustration.
Figure 1. Front view
1 Power indicator 2 Power button
3 Storage drive status indicator 4 Microphone connector
5 Headset connector 6 USB 3.0 connector
7 Always On USB 3.0 connector 8 Illuminated red dot
1 Power indicator
This indicator is on when the computer is on.
© Copyright Lenovo 2018, 2019 1
2 Power button
Used to turn on your computer. When you cannot shut down the computer from the operating system, press
and hold the power button for four or more seconds to turn off the computer.
3 Storage drive status indicator
This indicator is on when the storage drive is in use.
4 Microphone connector
Used to connect a microphone to your computer. You can use the microphone to record sounds or interact
with the computer using speech-recognition software.
5 Headset connector
Used to connect a headset or headphones to your computer.
6 USB 3.0 connector
Used to connect a USB-compatible device, such as a USB keyboard, mouse, scanner, printer, or personal
digital assistant (PDA). For optimal data transfer, connect a USB 3.0 device to a USB 3.0 connector instead
of a USB 2.0 connector.
7 Always On USB 3.0 connector
Used to connect a device that requires a USB 2.0 or USB 3.0 connection, such as a keyboard, a mouse, a
scanner, a printer, or a personal digital assistant (PDA). With the power adapter connected, you can charge
the automatically detected device even when the computer is in hibernation mode or turned off.
8 Illuminated red dot
This indicator is on when the computer is on.
Rear view
Note: Your computer model might look slightly different from the illustration.
2M625q User Guide and Hardware Maintenance Manual
Figure 2. Rear view
1 Optional connector 1 2 Optional connector 2
3 Security-lock slot 4 Wi-Fi antenna slot
5 Ethernet connector 6 USB 2.0 connectors
7 USB 2.0 connector 8 DisplayPort® connector
9 USB 3.0 connector 10 DisplayPort connector
11 Power adapter connector
1 Optional connector 1
Depending on the computer model, the connector might vary.
2 Optional connector 2
Depending on the computer model, the connector might vary.
3 Security-lock slot
Used to secure a Kensington-style cable lock.
Chapter 1.Overview 3
4 Wi-Fi antenna slot
Used to install the rear Wi-Fi antenna cable connector that is available only on some models. The rear Wi-Fi
antenna is installed on the rear Wi-Fi antenna cable connector.
5 Ethernet connector
Used to connect an Ethernet cable for network access.
6 USB 2.0 connector
Used to connect a USB-compatible device. For optimal data transfer, connect a USB 2.0 device to a USB
2.0 connector.
7 USB 2.0 connector
Used to connect a USB-compatible device. For optimal data transfer, connect a USB 2.0 device to a USB
2.0 connector.
8 DisplayPort connector
Used to send audio and video signals from the computer to another audio or video device, such as a high-
performance monitor.
9 USB 3.0 connector
Used to connect a USB-compatible device. For optimal data transfer, connect a USB 3.0 device to a USB
3.0 connector instead of a USB 2.0 connector.
10 DisplayPort connector
Used to send audio and video signals from the computer to another audio or video device, such as a high-
performance monitor.
11 Power adapter connector
Used to connect the power adapter to your computer for power supply.
System board
Note: See “Front view” on page 1 and “Rear view” on page 2 for additional component descriptions.
4M625q User Guide and Hardware Maintenance Manual
1 Serial connector 1 2 Serial connector 2
3 USB 2.0 connector 4 DisplayPort connector
5 System fan connector 6 Coin-cell battery
7 M.2 Wi-Fi card slot 8 Storage drive slot
9 Internal speaker connector 10 M.2 storage drive slot
11 Memory slot
Machine type and model label
The machine type and model label identifies the computer. When you contact Lenovo for help, the machine
type and model information helps support technicians to identify the computer and provide faster service.
The machine type and model label is attached on the top of the computer as shown.
Figure 4. Machine type and model label
6M625q User Guide and Hardware Maintenance Manual
Chapter 2. Specifications
Power supply
• 65-watt automatic voltage-sensing power supply
Storage drives
• 2.5-inch storage drive
• M.2 storage drive
Video features
• The integrated graphics card supports the following:
– DisplayPort connector
Audio features
• The integrated audio card supports the following:
– Headset connector
– Internal speaker
Input/Output (I/O) features
• Audio connectors (headset and microphone)
• DisplayPort connector
• Ethernet connector
• Serial connector (optional)
• Type-C USB connector (optional)
• USB connector
• VGA connector (optional)
Network features
• Ethernet LAN
• Wireless LAN (optional)
• Bluetooth (optional)
Physical dimensions
• Width: 35 mm (1.4 inches)
• Height: 183 mm (7.2 inches)
• Depth: 179 mm (7.1 inches)
Weight (without the package)
Maximum configuration as shipped: 1.1 kg (2.4 lb)
Statement on USB transfer rate
Depending on many factors such as the processing capability of the host and peripheral devices, file
attributes, and other factors related to system configuration and operating environments, the actual transfer
© Copyright Lenovo 2018, 2019 7
rate using the various USB connectors on this device will vary and will be slower than the data rate listed
below for each corresponding device.
USB device Data rate (Gbit/s)
3.1 Gen 1 5
3.1 Gen 2 10
3.2 20
8M625q User Guide and Hardware Maintenance Manual
Chapter 3. Computer locks
This chapter provides instructions on how to lock your computer with the locking devices to keep your
computer safe.
Attaching a Kensington-style cable lock
You can use a Kensington-style cable lock to secure your computer to a desk, table, or other nonpermanent
fixture. The cable lock connects to the security-lock slot at the rear of your computer. Depending on the type
selected, the cable lock can be operated with a key or combination. The cable lock also locks the buttons
used to open the computer cover. This is the same type of lock used with many notebook computers. You
can order such a cable lock directly from Lenovo by searching for Kensington at:
http://www.lenovo.com/support
Figure 5. Attaching a Kensington-style cable lock
© Copyright Lenovo 2018, 2019 9
10 M625q User Guide and Hardware Maintenance Manual
Chapter 4. Replacing hardware
This chapter provides instructions on how to replace hardware for your computer.
Before replacing hardware
Attention: Do not open your computer or attempt any repairs before reading this section and the Important
Product Information Guide.
Notes before replacing hardware
• Use computer components provided only by Lenovo.
• When installing or replacing an option, use the appropriate instructions explained in this manual along with
the instructions that come with the option.
• In most areas of the world, Lenovo requires the return of defective CRUs. Information about this will come
with the CRU or will come a few days after the CRU arrives.
Handling static-sensitive devices
Do not open the static-protective package containing the new part until the defective part has been removed
and you are ready to install the new part. Static electricity, although harmless to you, can seriously damage
computer components and options.
When you handle options and other computer components, take these precautions to avoid static-electricity
damage:
• Limit your movement. Movement can cause static electricity to build up around you.
• Always handle options and other computer components carefully. Handle PCI/PCIe cards, memory
modules, system boards, and microprocessors by the edges. Never touch any exposed circuitry.
• Prevent others from touching the options and other computer components.
• Touch the static-protective package containing the part to a metal expansion-slot cover or other
unpainted metal surface on the computer for at least two seconds. This reduces static electricity from the
package and your body before you install or replace a new part.
• When possible, remove the new part from the static-protective package, and install it directly in the
computer without setting the part down. When this is not possible, place the static-protective package on
a smooth, level surface and place the part on the package.
• Do not place the part on the computer cover or other metal surface.
Knowing FRUs (including CRUs)
• Field Replaceable Units (FRUs) are computer parts that a trained technician can upgrade or replace. FRUs
include all CRUs. For detailed FRU information, such as the FRU part numbers and supported computer
models, go to:
http://www.lenovo.com/serviceparts-lookup
• Customer Replaceable Units (CRUs) are computer parts that a user can upgrade or replace.
– Self-service CRUs: You can install self-service CRUs easily. These CRUs might be stand-alone,
latched, or secured by up to two screws. Examples of self-service CRUs include the keyboard, mouse,
any USB device. You are responsible for replacing all self-service CRUs.
– Optional-service CRUs: Handling optional-service CRUs requires some technical skills and simple tools
(such as a screwdriver). These CRUs are isolated parts within the computer. They are usually
© Copyright Lenovo 2018, 2019 11
concealed by an access panel that is secured by more than two screws. You must remove the screws
and panel to access the specific CRU. Optional-service CRUs can be removed and installed by users
or, during the warranty period, by a Lenovo service technician.
Before replacing FRUs
Before replacing any FRU, read the following:
• Only certified and trained personnel can service the computer.
• Before replacing an FRU, read the entire section about replacing the part.
• Be extremely careful during writing operations such as copying, saving, or formatting.
The sequence of the drives in the computer that you are servicing might have been altered. If you select
an incorrect drive, data or programs might be overwritten.
• Replace an FRU only with another FRU of the correct model.
When you replace an FRU, ensure that the model of the machine and the FRU part number are correct.
• An FRU should not be replaced because of a single, unreproducible failure.
Single failures can occur for a variety of reasons that have nothing to do with a hardware defect, such as
cosmic radiation, electrostatic discharge, or software errors. Consider replacing an FRU only when a
problem recurs. If you suspect that an FRU is defective, clear the error log and run the test again. If the
error does not recur, do not replace the FRU.
• Only replace a defective FRU.
12 M625q User Guide and Hardware Maintenance Manual
Locating FRUs (including CRUs)
Locating FRUs (including CRUs) for 10TF, 10TG, 10TH, 10TJ, and 10TK models
Figure 6. Locating FRUs (including CRUs)
Notes:
• Some of the components are optional.
• To replace a component that is not in the list below, contact a Lenovo service technician. For a list of
Lenovo Support phone numbers, go to:
http://www.lenovo.com/serviceparts-lookup
Chapter 4.Replacing hardware 13
Number FRU description Self-service CRU Optional-service
CRU
1Vertical stand Yes No
2Power adapter bracket Yes No
3Power adapter Yes No
4Computer cover Yes No
5Dust shield Yes No
6Power cord Yes No
7Internal speaker Yes No
8System board No No
9Heat sink No Yes
10 Antenna bracket No No
11 System fan No No
12 Chassis No No
13 Bottom cover Yes No
14 Memory module Yes No
15 M.2 storage drive Yes No
16 Storage drive cable No No
17 Storage drive No Yes
18 Storage drive bracket No Yes
19 Wi-Fi card shield No Yes
20 Wi-Fi card No Yes
21 Coin-cell battery No No
22 Wi-Fi antennas No No
23 Storage drive assembly bracket No No
24 VESA® mount bracket Yes No
25 Keyboard or wireless keyboard Yes No
26 Mouse or wireless mouse Yes No
14 M625q User Guide and Hardware Maintenance Manual
Locating FRUs (including CRUs) for 10TL, 10UY, 10V0, 10V1, and 10V2 models
Figure 7. Locating FRUs (including CRUs)
Notes:
• Some of the components are optional.
• To replace a component that is not in the list below, contact a Lenovo service technician. For a list of
Lenovo Support phone numbers, go to:
http://www.lenovo.com/support/phone
Number FRU description Self-service CRU Optional-service
CRU
1Vertical stand Yes No
2Power adapter bracket Yes No
3Power adapter Yes No
Chapter 4.Replacing hardware 15
Number FRU description Self-service CRU Optional-service
CRU
4Computer cover Yes No
5Internal speaker Yes No
6Power cord Yes No
7System board No No
8Antenna bracket No No
9Heat sink No Yes
10 Chassis No No
11 Bottom cover Yes No
12 Memory module Yes No
13 M.2 storage drive Yes No
14 Wi-Fi card shield No Yes
15 Wi-Fi card No Yes
16 Wi-Fi antennas No No
17 Coin-cell battery No No
18 VESA mount bracket Yes No
19 Keyboard or wireless keyboard Yes No
20 Mouse or wireless mouse Yes No
Replacing the keyboard or wireless keyboard
Note: The wireless keyboard is available only on some models.
Replacing the keyboard
1. Turn off the computer and disconnect all power cords from electrical outlets.
2. Disconnect the old keyboard cable from the computer.
3. Connect a new keyboard to the appropriate connector on the computer.
Figure 8. Replacing the keyboard
16 M625q User Guide and Hardware Maintenance Manual
Replacing the wireless keyboard
1. Remove your old wireless keyboard.
2. Take out the new wireless keyboard from the package.
3. Open the battery compartment cover, and install two AAA batteries according to the polarity indicators.
Figure 9. Replacing the wireless keyboard
4. Remove the USB dongle from the keyboard compartment or from the wireless mouse compartment and
connect it to an available USB connector on the computer.
5. Close the compartment cover. The keyboard is ready for use.
Replacing the mouse or wireless mouse
Note: The wireless mouse is available only on some models.
Replacing the mouse
1. Turn off the computer and disconnect all power cords from electrical outlets.
2. Disconnect the old mouse cable from the computer.
3. Connect a new mouse to the appropriate connector on the computer.
Figure 10. Replacing the mouse
Chapter 4.Replacing hardware 17
Replacing the wireless mouse
1. Disconnect the USB dongle from your computer. Then, remove your old wireless mouse.
2. Remove the new wireless mouse from the package.
3. Open the battery compartment cover, and install two AAA batteries according to the polarity indicators.
a. Open the battery compartment.
Figure 11. Opening the battery compartment
b. Take out the USB dongle.
18 M625q User Guide and Hardware Maintenance Manual
Figure 14. Installing the mouse batteries
e. Close the battery compartment cover.
Figure 15. Closing the battery compartment cover
f. Push the power switch to the on position.
20 M625q User Guide and Hardware Maintenance Manual
Figure 16. Pushing the power switch to the on position
Notes:
• The green LED indicates that the mouse is ready for use.
• The flashing amber LED indicates a low battery level.
• Push the power switch to the off position when you are not using the mouse to extend the battery
life.
• After disconnecting the USB dongle from your computer, store it in the wireless mouse
compartment or in the wireless keyboard compartment.
Replacing the power adapter
Attention: Do not open your computer or attempt any repairs before reading the Important Product Information
Guide.
1. Remove any media from the drives and turn off all connected devices and the computer.
2. Disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.
3. Replace the power adapter.
Note: Your power cord might look different from the one illustrated.
a. Remove the power adapter.
Chapter 4.Replacing hardware 21
Figure 17. Removing the power adapter
b. Remove the power cord.
Figure 18. Removing the power cord
c. Install the power cord.
22 M625q User Guide and Hardware Maintenance Manual
Replacing the vertical stand
Attention: Do not open your computer or attempt any repairs before reading the Important Product Information
Guide.
1. Remove any media from the drives and turn off all connected devices and the computer.
2. Disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.
3. Replace the vertical stand.
a. Remove the vertical stand.
Figure 21. Removing the vertical stand
b. Install the vertical stand.
24 M625q User Guide and Hardware Maintenance Manual
Figure 22. Installing the vertical stand
Replacing the VESA mount bracket
Attention: Do not open your computer or attempt any repairs before reading the Important Product Information
Guide.
1. Remove any media from the drives and turn off all connected devices and the computer.
2. Disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.
3. Replace the VESA mount bracket.
a. Remove the VESA mount bracket.
Chapter 4.Replacing hardware 25
Figure 23. Removing the VESA mount bracket
b. Install the VESA mount bracket.
Figure 24. Installing the VESA mount bracket
Replacing the power adapter bracket
Attention: Do not open your computer or attempt any repairs before reading the Important Product Information
Guide.
26 M625q User Guide and Hardware Maintenance Manual
1. Remove any media from the drives and turn off all connected devices and the computer.
2. Disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.
3. Replace the power adapter bracket.
a. Remove the power adapter bracket.
Figure 25. Removing the power adapter bracket
b. Install the power adapter bracket.
Figure 26. Installing the power adapter bracket
Chapter 4.Replacing hardware 27
Removing the computer cover
Attention: Do not open your computer or attempt any repairs before reading the Important Product Information
Guide.
Removing the computer cover for 10TF, 10TG, 10TH, 10TJ, and 10TK models
CAUTION:
Before you open the computer cover, turn off the computer and wait several minutes until
the computer is cool.
1. Remove any media from the drives and turn off all connected devices and the computer.
2. Disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.
3. Remove the dust shield.
Figure 27. Removing the dust shield
4. Remove the computer cover.
28 M625q User Guide and Hardware Maintenance Manual
Figure 28. Removing the computer cover
Removing the computer cover for 10TL, 10UY, 10V0, 10V1, and 10V2 models
CAUTION:
Before you open the computer cover, turn off the computer and wait several minutes until
the computer is cool.
1. Remove any media from the drives and turn off all connected devices and the computer.
2. Disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.
3. Remove the computer cover.
Chapter 4.Replacing hardware 29
Figure 29. Removing the computer cover
Replacing the storage drive for 10TF, 10TG, 10TH, 10TJ, and 10TK
models
Attention: Do not open your computer or attempt any repairs before reading the Important Product Information
Guide.
1. Remove any media from the drives and turn off all connected devices and the computer.
2. Disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.
3. Remove the computer cover. For details, see “Removing the computer cover” on page 28.
4. Replace the storage drive.
a. Remove the storage drive.
30 M625q User Guide and Hardware Maintenance Manual
Figure 32. Installing the storage drive bracket
e. Connect the storage drive cable to the system board.
f. Install the storage drive.
32 M625q User Guide and Hardware Maintenance Manual
Figure 33. Installing the storage drive
5. Reinstall the computer cover and reconnect the cables. For details, see “Completing the parts
replacement” on page 64.
Replacing the storage drive cable for 10TF, 10TG, 10TH, 10TJ, and 10TK
models
Attention: Do not open your computer or attempt any repairs before reading the Important Product Information
Guide.
1. Remove any media from the drives and turn off all connected devices and the computer.
2. Disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.
3. Remove the computer cover. For details, see “Removing the computer cover” on page 28.
4. Remove the storage drive. For details, see “Replacing the storage drive for 10TF, 10TG, 10TH, 10TJ,
and 10TK models” on page 30.
5. Replace the storage drive cable.
a. Remove the storage drive cable.
Chapter 4.Replacing hardware 33
Figure 34. Removing the storage drive cable
b. Install the storage drive cable.
Figure 35. Installing the storage drive cable
6. Reinstall the computer cover and reconnect the cables. For details, see “Completing the parts
replacement” on page 64.
Replacing the system fan for 10TF, 10TG, 10TH, 10TJ, and 10TK models
Attention: Do not open your computer or attempt any repairs before reading the Important Product Information
Guide.
1. Remove any media from the drives and turn off all connected devices and the computer.
34 M625q User Guide and Hardware Maintenance Manual
2. Disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.
3. Remove the computer cover. For details, see “Removing the computer cover” on page 28.
4. Disconnect the system fan cable from the system fan connector on the system board. See “System
board” on page 4.
5. Replace the system fan.
a. Remove the system fan.
Figure 36. Removing the system fan
b. Install the system fan.
Chapter 4.Replacing hardware 35
Figure 37. Installing the system fan
6. Connect the system fan cable to the system fan connector on the system board. See “System board” on
page 4.
7. Reinstall the computer cover and reconnect the cables. For details, see “Completing the parts
replacement” on page 64.
Replacing the heat sink
Attention: Do not open your computer or attempt any repairs before reading the Important Product Information
Guide.
Replacing the heat sink for 10TF, 10TG, 10TH, 10TJ, and 10TK models
1. Remove any media from the drives and turn off all connected devices and the computer.
2. Disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.
3. Remove the computer cover. For details, see “Removing the computer cover” on page 28.
4. Replace the heat sink.
a. Remove the heat sink.
36 M625q User Guide and Hardware Maintenance Manual
Replacing the heat sink for 10TL, 10UY, 10V0, 10V1, and 10V2 models
1. Remove any media from the drives and turn off all connected devices and the computer.
2. Disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.
3. Remove the computer cover. For details, see “Removing the computer cover” on page 28.
4. Replace the heat sink.
a. Remove the heat sink.
Figure 40. Removing the heat sink
b. Install the heat sink.
38 M625q User Guide and Hardware Maintenance Manual
Figure 41. Installing the heat sink
5. Reinstall the computer cover and reconnect the cables. For details, see “Completing the parts
replacement” on page 64.
Replacing the internal speaker
Attention: Do not open your computer or attempt any repairs before reading the Important Product Information
Guide.
1. Remove any media from the drives and turn off all connected devices and the computer.
2. Disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.
3. Remove the computer cover. For details, see “Removing the computer cover” on page 28.
4. Disconnect the internal speaker cable from the internal speaker connector on the system board.
5. Replace the internal speaker.
a. Remove the internal speaker.
Chapter 4.Replacing hardware 39
Figure 42. Removing the internal speaker
b. Install the internal speaker.
Figure 43. Installing the internal speaker
6. Connect the internal speaker cable to the internal speaker connector on the system board.
7. Reinstall the computer cover and reconnect the cables. For details, see “Completing the parts
replacement” on page 64.
Replacing the Wi-Fi card
Attention: Do not open your computer or attempt any repairs before reading the Important Product Information
Guide.
1. Remove any media from the drives and turn off all connected devices and the computer.
40 M625q User Guide and Hardware Maintenance Manual
2. Disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.
3. Remove the computer cover. For details, see “Removing the computer cover” on page 28.
4. Remove the storage drive if necessary. For details, see “Replacing the storage drive for 10TF, 10TG,
10TH, 10TJ, and 10TK models” on page 30.
5. Remove the heat sink if necessary. For details, see “Replacing the heat sink” on page 36.
6. Depending on your computer model, refer to one of the following to replace the Wi-Fi card.
• Type 1
a. Remove the Wi-Fi card shield.
Figure 44. Removing the Wi-Fi card shield
b. Disconnect the Wi-Fi antennas.
Figure 45. Disconnecting the Wi-Fi antennas
c. Remove the Wi-Fi card.
Chapter 4.Replacing hardware 41
Figure 46. Removing the Wi-Fi card
d. Install the Wi-Fi card.
Figure 47. Installing the Wi-Fi card
e. Connect the Wi-Fi antennas.
Figure 48. Connecting the Wi-Fi antennas
f. Install the Wi-Fi card shield.
42 M625q User Guide and Hardware Maintenance Manual
c. Remove the Wi-Fi card.
Figure 52. Removing the Wi-Fi card
d. Install the Wi-Fi card.
Figure 53. Installing the Wi-Fi card
e. Connect the Wi-Fi antennas.
Figure 54. Connecting the Wi-Fi antennas
f. Install the Wi-Fi card shield.
44 M625q User Guide and Hardware Maintenance Manual
Figure 55. Install the Wi-Fi card shield
7. Reinstall the computer cover and reconnect the cables. For details, see “Completing the parts
replacement” on page 64.
Replacing the Wi-Fi antennas
Attention: Do not open your computer or attempt any repairs before reading the Important Product Information
Guide.
Replacing the front Wi-Fi antenna
1. Remove any media from the drives and turn off all connected devices and the computer.
2. Disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.
3. Remove the computer cover. For details, see “Removing the computer cover” on page 28.
4. Remove the storage drive if necessary. For details, see “Replacing the storage drive for 10TF, 10TG,
10TH, 10TJ, and 10TK models” on page 30.
5. Replace the front Wi-Fi antenna.
a. Disconnect the front Wi-Fi antenna cable from the Wi-Fi card.
Chapter 4.Replacing hardware 45
Figure 56. Disconnecting the front Wi-Fi antenna cable from the Wi-Fi card
b. Remove the front Wi-Fi antenna.
Figure 57. Removing the front Wi-Fi antenna
c. Install the front Wi-Fi antenna.
46 M625q User Guide and Hardware Maintenance Manual
Figure 58. Installing the front Wi-Fi antenna
d. Connect the front Wi-Fi antenna cable to the Wi-Fi card.
Figure 59. Connecting the front Wi-Fi antenna cable to the Wi-Fi card
6. Reinstall the computer cover and reconnect the cables. For details, see “Completing the parts
replacement” on page 64.
Replacing the rear Wi-Fi antenna
1. Remove any media from the drives and turn off all connected devices and the computer.
2. Disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.
3. Remove the computer cover. For details, see “Removing the computer cover” on page 28.
Chapter 4.Replacing hardware 47
4. Remove the storage drive if necessary. For details, see “Replacing the storage drive for 10TF, 10TG,
10TH, 10TJ, and 10TK models” on page 30.
5. Disconnect the rear Wi-Fi antenna cable from the Wi-Fi card.
6. Replace the rear Wi-Fi antenna.
Note: Record the cable routing before removing the rear Wi-Fi antenna cable.
a. Remove the rear Wi-Fi antenna.
Figure 60. Removing the rear Wi-Fi antenna
b. Remove the screw cover that secures the rear Wi-Fi antenna cable.
Figure 61. Removing the screw cover that secures the rear Wi-Fi antenna cable
48 M625q User Guide and Hardware Maintenance Manual
Figure 64. Installing the screw cover to secure the rear Wi-Fi antenna cable
f. Install the rear Wi-Fi antenna.
Figure 65. Installing the rear Wi-Fi antenna
7. Connect the rear Wi-Fi antenna cable to the Wi-Fi card.
8. Reinstall the computer cover and reconnect the cables. For details, see “Completing the parts
replacement” on page 64.
Replacing the antenna bracket
Attention: Do not open your computer or attempt any repairs before reading the Important Product Information
Guide.
Replacing the antenna bracket for 10TF, 10TG, 10TH, 10TJ, and 10TK models
1. Remove any media from the drives and turn off all connected devices and the computer.
50 M625q User Guide and Hardware Maintenance Manual
2. Disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.
3. Remove the computer cover. For details, see “Removing the computer cover” on page 28.
4. Remove the storage drive. For details, see “Replacing the storage drive for 10TF, 10TG, 10TH, 10TJ,
and 10TK models” on page 30.
5. Remove the front Wi-Fi antennas. For details, see “Replacing the Wi-Fi antennas” on page 45.
6. Replace the antenna bracket.
a. Remove the storage drive assembly bracket.
Figure 66. Removing the storage drive assembly bracket
b. Remove the antenna bracket.
Chapter 4.Replacing hardware 51
Figure 67. Removing the antenna bracket
c. Install the antenna bracket.
Figure 68. Installing the antenna bracket
d. Install the storage drive assembly bracket.
52 M625q User Guide and Hardware Maintenance Manual
Figure 69. Installing the storage drive assembly bracket
7. Reinstall the computer cover and reconnect the cables. For details, see “Completing the parts
replacement” on page 64.
Replacing the antenna bracket for 10TL, 10UY, 10V0, 10V1, and 10V2 models
1. Remove any media from the drives and turn off all connected devices and the computer.
2. Disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.
3. Remove the computer cover. For details, see “Removing the computer cover” on page 28.
4. Remove the front Wi-Fi antenna. For details, see “Replacing the Wi-Fi antennas” on page 45.
5. Replace the antenna bracket.
a. Remove the antenna bracket.
Chapter 4.Replacing hardware 53
Figure 70. Removing the antenna bracket
b. Install the antenna bracket.
Figure 71. Installing the antenna bracket
6. Reinstall the computer cover and reconnect the cables. For details, see “Completing the parts
replacement” on page 64.
Replacing the coin-cell battery
Attention: Do not open your computer or attempt any repairs before reading the Important Product Information
Guide.
Your computer has a special type of memory that maintains the date, time, and settings for built-in features,
such as parallel connector assignments (configurations). A coin-cell battery keeps this information active
when you turn off the computer.
54 M625q User Guide and Hardware Maintenance Manual
The coin-cell battery normally requires no charging or maintenance throughout its life; however, no coin-cell
battery lasts forever. If the coin-cell battery fails, the date, time, and configuration information (including
passwords) are lost. An error message is displayed when you turn on the computer.
1. Remove any media from the drives and turn off all connected devices and the computer.
2. Disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.
3. Remove the computer cover. For details, see “Removing the computer cover” on page 28.
4. Remove the storage drive if necessary. For details, see “Replacing the storage drive for 10TF, 10TG,
10TH, 10TJ, and 10TK models” on page 30.
5. Remove the heat sink if necessary. For details, see “Replacing the heat sink” on page 36.
6. Replace the coin-cell battery.
a. Press the metallic tab as shown.
Figure 72. Unlocking the microprocessor socket retainer
b. Remove the coin-cell battery.
Figure 73. Pivoting the microprocessor socket upward
Chapter 4.Replacing hardware 55
c. Install the coin-cell battery.
Figure 74. Removing the microprocessor
d. Press the coin-cell battery downward until it snaps into position.
Figure 75. Installing the microprocessor
7. Reinstall the computer cover and reconnect the cables. For details, see “Completing the parts
replacement” on page 64.
To dispose of the coin-cell battery, refer to the “Lithium coin-cell battery notice” topic in the Safety and
Warranty Guide.
Replacing the bottom cover
Attention: Do not open your computer or attempt any repairs before reading the Important Product Information
Guide.
1. Remove any media from the drives and turn off all connected devices and the computer.
56 M625q User Guide and Hardware Maintenance Manual
2. Disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.
3. Remove the computer cover. For details, see “Removing the computer cover” on page 28.
4. Replace the bottom cover.
a. Remove the bottom cover.
Figure 76. Removing the bottom cover
b. Install the bottom cover.
Figure 77. Installing the bottom cover
5. Reinstall the computer cover and reconnect the cables. For details, see “Completing the parts
replacement” on page 64.
Chapter 4.Replacing hardware 57
Replacing the memory module
Attention: Do not open your computer or attempt any repairs before reading the Important Product Information
Guide.
1. Remove any media from the drives and turn off all connected devices and the computer.
2. Disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.
3. Remove the computer cover. For details, see “Removing the computer cover” on page 28.
4. Remove the bottom cover. For details, see “Replacing the bottom cover” on page 56.
5. Replace the memory module.
a. Open the memory module retainer.
Figure 78. Opening the memory module retainer
b. Remove the memory module.
Figure 79. Removing the memory module
c. Install the memory module.
58 M625q User Guide and Hardware Maintenance Manual
Figure 80. Installing the memory module
d. Close the memory module retainer.
Figure 81. Closing the memory module retainer
6. Reinstall the computer cover and reconnect the cables. For details, see “Completing the parts
replacement” on page 64.
Replacing the M.2 storage drive
Attention: Do not open your computer or attempt any repairs before reading the Important Product Information
Guide.
1. Remove any media from the drives and turn off all connected devices and the computer.
2. Disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.
3. Remove the computer cover. For details, see “Removing the computer cover” on page 28.
4. Remove the bottom cover. For details, see “Replacing the bottom cover” on page 56.
5. Replace the M.2 storage drive.
a. Unlock the M.2 storage drive clip.
Chapter 4.Replacing hardware 59
Figure 82. Unlocking the M.2 storage drive clip
b. Remove the M.2 storage drive.
Figure 83. Removing the M.2 storage drive
c. Install the M.2 storage drive.
Figure 84. Installing the M.2 storage drive
d. Lock the M.2 storage drive clip.
60 M625q User Guide and Hardware Maintenance Manual
Figure 85. Locking the M.2 storage drive clip
6. Reinstall the computer cover and reconnect the cables. For details, see “Completing the parts
replacement” on page 64.
Replacing the system board and chassis
Attention: Do not open your computer or attempt any repairs before reading the Important Product Information
Guide.
1. Remove any media from the drives and turn off all connected devices and the computer.
2. Disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.
3. Remove the computer cover. For details, see “Removing the computer cover” on page 28.
4. Remove the storage drive if necessary. For details, see “Replacing the storage drive for 10TF, 10TG,
10TH, 10TJ, and 10TK models” on page 30.
5. Remove the system fan if necessary. For details, see “Replacing the system fan for 10TF, 10TG, 10TH,
10TJ, and 10TK models” on page 34.
6. Remove the heat sink. For details, see “Replacing the heat sink” on page 36.
7. Remove the internal speaker. For details, see “Replacing the internal speaker” on page 39.
8. Remove the Wi-Fi card. For details, see “Replacing the Wi-Fi card” on page 40.
9. Remove the Wi-Fi antennas. For details, see “Replacing the Wi-Fi antennas” on page 45.
10. Remove the antenna bracket. For details, see “Replacing the antenna bracket” on page 50.
11. Remove the bottom cover. For details, see “Replacing the bottom cover” on page 56.
12. Remove the memory module. For details, see “Replacing the memory module” on page 58.
13. Remove the M.2 storage drive. For details, see “Replacing the M.2 storage drive” on page 59.
14. Record the cable routing and cable connections, and then disconnect all cables from the system board.
See “System board” on page 4.
15. Replace the system board and chassis.
Note: Carefully handle the system board by its edges.
a. Remove the screws that secure the system board.
Chapter 4.Replacing hardware 61
Figure 86. Removing the screws that secure the system board
b. Remove the system board.
Figure 87. Removing the system board
c. Install the system board.
62 M625q User Guide and Hardware Maintenance Manual
Figure 88. Installing the system board
d. Install the screws to secure the system board.
Figure 89. Installing the screws to secure the system board
16. Route all the cables that you disconnected from the failing system board, and then reconnect the cables
to the new system board. See “System board” on page 4.
17. Reinstall the computer cover and reconnect the cables. For details, see “Completing the parts
replacement” on page 64.
Chapter 4.Replacing hardware 63
Completing the parts replacement
Completing the parts replacement for 10TF, 10TG, 10TH, 10TJ, and 10TK models
After completing the installation or replacement for all parts, reinstall the computer cover and reconnect the
cables.
To reinstall the computer cover and reconnect the cables to your computer, do the following:
1. Ensure that all components have been reassembled correctly and that no tools or loose screws are left
inside your computer.
2. Ensure that the cables are routed correctly before reinstalling the computer cover. Keep cables clear of
the hinges and sides of the computer chassis to avoid interference when reinstalling the computer
cover.
3. Reinstall the computer cover.
Figure 90. Reinstalling the computer cover
4. Install the screw to secure the computer cover.
5. Reinstall the dust shield.
64 M625q User Guide and Hardware Maintenance Manual
Figure 91. Reinstalling the dust shield
6. Place the computer in an upright position.
7. If a locking device is available, use it to lock the computer.
8. Reconnect the external cables and power cords to the corresponding connectors on the computer.
Completing the parts replacement for 10TL, 10UY, 10V0, 10V1, and 10V2 models
After completing the installation or replacement for all parts, reinstall the computer cover and reconnect the
cables.
To reinstall the computer cover and reconnect the cables to your computer, do the following:
1. Ensure that all components have been reassembled correctly and that no tools or loose screws are left
inside your computer.
2. Ensure that the cables are routed correctly before reinstalling the computer cover. Keep cables clear of
the hinges and sides of the computer chassis to avoid interference when reinstalling the computer
cover.
3. Reinstall the computer cover.
Chapter 4.Replacing hardware 65
Figure 92. Reinstalling the computer cover
4. Install the screw to secure the computer cover.
5. Place the computer in an upright position.
6. If a locking device is available, use it to lock the computer.
7. Reconnect the external cables and power cords to the corresponding connectors on the computer.
66 M625q User Guide and Hardware Maintenance Manual
Appendix A. Notices
Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult
your local Lenovo representative for information on the products and services currently available in your
area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that
Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service
that does not infringe any Lenovo intellectual property right may be used instead. However, it is the user's
responsibility to evaluate and verify the operation of any other product, program, or service.
Lenovo may have patents or pending patent applications covering subject matter described in this
document. The furnishing of this document does not give you any license to these patents. You can send
license inquiries, in writing, to:
Lenovo (United States), Inc.
1009 Think Place - Building One
Morrisville, NC 27560
U.S.A.
Attention: Lenovo Director of Licensing
LENOVO PROVIDES THIS PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow
disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply to
you.
This information could include technical inaccuracies or typographical errors. Changes are periodically made
to the information herein; these changes will be incorporated in new editions of the publication. Lenovo may
make improvements and/or changes in the products and/or the programs described in this publication at any
time without notice.
The products described in this document are not intended for use in implantation or other life support
applications where malfunction may result in injury or death to persons. The information contained in this
document does not affect or change Lenovo product specifications or warranties. Nothing in this document
shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo or
third parties. All information contained in this document was obtained in specific environments and is
presented as an illustration. The result obtained in other operating environments may vary.
Lenovo may use or distribute any of the information you supply in any way it believes appropriate without
incurring any obligation to you.
Any references in this publication to non-Lenovo Web sites are provided for convenience only and do not in
any manner serve as an endorsement of those Web sites. The materials at those Web sites are not part of the
materials for this Lenovo product, and use of those Web sites is at your own risk.
Any performance data contained herein was determined in a controlled environment. Therefore, the result
obtained in other operating environments may vary significantly. Some measurements may have been made
on development-level systems and there is no guarantee that these measurements will be the same on
generally available systems. Furthermore, some measurements may have been estimated through
extrapolation. Actual results may vary. Users of this document should verify the applicable data for their
specific environment.
© Copyright Lenovo 2018, 2019 67
68 M625q User Guide and Hardware Maintenance Manual
Appendix B. Trademarks
LENOVO, LENOVO logo, and the THINKCENTRE logo are trademarks of Lenovo.
DisplayPort is a trademark of the Video Electronics Standards Association.
VESA is a trademark of the Video Electronics Standards Association.
All other trademarks are the property of their respective owners. © 2019 Lenovo.
© Copyright Lenovo 2018, 2019 69
70 M625q User Guide and Hardware Maintenance Manual
