Lenovo M920 User Manual

Displayed below is the user manual for M920 by Lenovo which is a product in the PCs/Workstations category. This manual has pages.

Related Manuals

Lenovo M920 Manual

M920t User Guide and Hardware Maintenance

Manual

Energy Star Machine Types: 10SF, 10SG, 10SH, 10TM, 10U0 and

10U1

Note: Before using this information and the product it supports, be sure to read and understand the

Important Product Information Guide and Appendix A “Notices” on page 71.

First Edition (June 2018)

LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant to a General Services

Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-

35F-05925.

Contents

Chapter 1. Overview. . . . . . . . . . . 1

Front view . . . . . . . . . . . . . . . . . . 1

Rear view . . . . . . . . . . . . . . . . . . 3

System board . . . . . . . . . . . . . . . . 5

Machine type and model label . . . . . . . . . . 6

Chapter 2. Specifications . . . . . . . . 7

Chapter 3. Computer locks . . . . . . . 9

Enabling or disabling the E-lock . . . . . . . . . 9

Locking the computer cover . . . . . . . . . . 10

Attaching a Kensington-style cable lock . . . . . 11

Attaching a cable lock . . . . . . . . . . . . 12

Chapter 4. Replacing hardware . . . . 13

Before replacing hardware . . . . . . . . . . 13

Knowing FRUs (including CRUs) . . . . . . . . 13

Locating FRUs (including CRUs) . . . . . . . . 14

Replacing the power cord . . . . . . . . . . . 16

Removing the computer cover . . . . . . . . . 17

Replacing the front bezel . . . . . . . . . . . 18

Pivoting the drive bay assembly upward and

downward . . . . . . . . . . . . . . . . . 19

Replacing the computer handle . . . . . . . . 20

Replacing the optical drive . . . . . . . . . . 22

Replacing the power button . . . . . . . . . . 23

Replacing the card reader . . . . . . . . . . . 24

Replacing the front I/O bracket . . . . . . . . . 26

Replacing the front fan . . . . . . . . . . . . 27

Replacing the illuminated red dot . . . . . . . . 28

Replacing the thermal sensor . . . . . . . . . 29

Replacing the internal speaker . . . . . . . . . 30

Replacing the storage drive . . . . . . . . . . 31

Replacing the memory module . . . . . . . . . 43

Replacing the coin-cell battery . . . . . . . . . 44

Replacing a PCI Express card . . . . . . . . . 46

Replacing the M.2 storage drive . . . . . . . . 47

Replacing the M.2 storage drive bracket . . . . . 50

Replacing the Wi-Fi card . . . . . . . . . . . 51

Replacing the Wi-Fi antennas . . . . . . . . . 55

Replacing the heat sink and fan assembly . . . . 58

Replacing the power supply assembly . . . . . . 59

Replacing the microprocessor . . . . . . . . . 61

Replacing the E-lock . . . . . . . . . . . . . 63

Replacing the cover presence switch . . . . . . 64

Replacing the rear fan . . . . . . . . . . . . 65

Replacing the system board . . . . . . . . . . 67

Completing the parts replacement . . . . . . . 68

Appendix A. Notices. . . . . . . . . . 71

Appendix B. Trademarks . . . . . . . 73

ii M920t User Guide and Hardware Maintenance Manual

Chapter 1. Overview

This chapter provides basic information to help you get familiar with your computer.

Front view

Note: Your computer model might look slightly different from the illustration.

Figure 1. Front view

1 Optical drive eject/close button (optional) 2 Optical drive status indicator (optional)

3 Front-access storage enclosure 4 Card reader slot (optional)

5 USB 3.1 Gen 1 Type-C connector 6 Power button

7 Power indicator 8 Storage drive activity indicator

9 Microphone connector 10 Headset connector

11 USB 3.1 Gen 1 connectors (2) 12 USB 3.1 Gen 2 connectors (2)

13 Illuminated red dot 14 Internal speaker

1 Optical drive eject/close button

Used to eject the tray of the optical drive. After you insert a disc into the tray, press the eject/close button to

close the tray.

2 Optical drive status indicator

This indicator is on when the optical drive is in use.

3 Front-access storage enclosure

Used to provide access to the hot-swappable storage drive.

4 Card reader slot

Used to read data from a supported memory card.

5 USB 3.1 Gen 1 Type-C connector

Used to connect a USB-compatible device, such as a USB keyboard, mouse, scanner, printer, or personal

digital assistant (PDA). For optimal data transfer, connect a USB 3.1 Gen 1 device to a USB 3.1 Gen 1

connector instead of a USB 2.0 connector.

6 Power button

Used to turn on your computer. When you cannot shut down the computer from the operating system, press

and hold the power button for four or more seconds to turn off the computer.

7 Power indicator

This indicator is on when the computer is on.

8 Storage drive activity indicator

This indicator is on when the storage drive is in use.

9 Microphone connector

Used to connect a microphone to your computer. You can use the microphone to record sounds or interact

with the computer using speech-recognition software.

10 Headset connector

Used to connect headset to your computer.

11 USB 3.1 Gen 1 connectors

Used to connect a USB-compatible device. For optimal data transfer, connect a USB 3.1 Gen 1 device to a

USB 3.1 Gen 2 or USB 3.1 Gen 1 connector instead of a USB 2.0 connector.

12 USB 3.1 Gen 2 connectors

Used to connect a USB-compatible device. For optimal data transfer, connect a USB 3.1 Gen 2 device to a

USB 3.1 Gen 2 connector instead of a USB 3.1 Gen 1 or USB 2.0 connector.

13 Illuminated red dot

This indicator is on when the computer is on.

2M920t User Guide and Hardware Maintenance Manual

14 Internal speaker

Used to listen to the sounds from your computer without using a headset or headphones.

Rear view

Note: Your computer model might look slightly different from the illustration.

Figure 2. Rear view

1 Audio line-out connector 2 VGA-out connector

3 DisplayPort® 1.2 out connector 4 USB 3.1 Gen 1 connector

5 USB 3.1 Gen 1 connectors (3) 6 Power cord connector

7 Serial connector 8 PS/2 mouse connector (optional)

9 PS/2 keyboard connector (optional) 10 Ethernet connector

11 Rear Wi-Fi antenna cover 12 Serial connector (optional)

13 Padlock loop 14 Smart cable clip slots (2)

15 PCI-Express card area (different cards provide

different connectors)

16 Security-lock slot

1 Audio line-out connector

Used to send audio signals from the computer to external devices, such as powered stereo speakers,

headphones, or multimedia keyboards. To connect a stereo system or other external recording device,

Chapter 1.Overview 3

connect a cable between the audio line-in connector of the device and the audio line-out connector of the

computer.

Note: If your computer has both an audio line-out connector and a headset or headphone connector, always

use the headset connector or headphone connector for earphones, headphones, or a headset. The

headphone connector does not support headset microphones.

2 VGA-out connector

Used to send video signals from the computer to another video device, such as a monitor.

3 DisplayPort 1.2 out connector

Used to send audio and video signals from the computer to another audio or video device, such as a high-

performance monitor.

4 USB 3.1 Gen 1 connector

Used to connect a USB-compatible device. For optimal data transfer, connect a USB 3.1 Gen 1 device to a

USB 3.1 Gen 2 or USB 3.1 Gen 1 connector instead of a USB 2.0 connector. This connector supports the

smart power on feature that enables you to turn on the computer or wake it up from S4 hibernation mode by

pressing Alt+P on the keyboard. You can enable or disable the smart power on feature from the Setup Utility

program. For detailed information, see the Important Product Information Guide.

5 USB 3.1 Gen 1 connectors

Used to connect a USB-compatible device. For optimal data transfer, connect a USB 3.1 Gen 1 device to a

USB 3.1 Gen 2 or USB 3.1 Gen 1 connector instead of a USB 2.0 connector.

6 Power cord connector

Used to connect the power cord to your computer for power supply.

7 Serial connector

Used to connect an external modem, a serial printer, or other devices that use a serial connector.

8 PS/2 mouse connector

Used to connect a mouse, a trackball, or other pointing devices that use a PS/2 mouse connector.

9 PS/2 keyboard connector

Used to connect a keyboard that uses a Personal System/2 (PS/2) keyboard connector.

10 Ethernet connector

Used to connect an Ethernet cable for network access.

11 Rear Wi-Fi antenna cover

Used to protect the rear Wi-Fi antenna that is optional.

12 Serial connector

Used to connect an external modem, a serial printer, or other devices that use a serial connector.

4M920t User Guide and Hardware Maintenance Manual

13 Padlock loop

Used to secure a padlock.

14 Smart cable clip slots

Used to secure a smart cable clip.

15 PCI-Express card area

To improve the operating performance of the computer, you can connect PCI-Express cards into this area.

Depending on the computer model, the connectors in this area vary.

16 Security-lock slot

Used to secure a Kensington-style cable lock.

System board

Note: See “Front view” on page 1 and “Rear view” on page 3 for additional component descriptions.

Figure 3. System board

1 4-pin power connector 2 Microprocessor fan connector

3 Memory slot (DIMM1) 4 Memory slot (DIMM2)

5 Memory slot (DIMM3) 6 Memory slot (DIMM4)

7 Power button board connector 8 Internal speaker connector

9 10-pin power connector 10 SATA power connector

Chapter 1.Overview 5

11 SATA power connector 12 Auxiliary fan connector

13 SATA 3.0 connector 14 SATA 3.0 connector

15 SATA 3.0 connector 16 Clear CMOS jumper

17 SATA 3.0 connector 18 M.2 storage drive slot

19 M.2 Wi-Fi card slot 20 Thermal sensor connector

21 Illuminated red dot connector 22 Front USB 2.0 connector

23 Front USB 2.0 connector 24 Serial connector (optional)

25 Thunderbolt connector 26 PCI Express card slot (physical link width x16;

negotiable link width x4, x1)

27 PCI Express x1 card slot 28 PCI Express x16 graphics card slot

29 E-lock connector 30 System fan connector

31 Cover presence switch 32 Coin-cell battery

33 Microprocessor socket 34 PS/2 keyboard and mouse connector

Machine type and model label

The machine type and model label identifies the computer. When you contact Lenovo for help, the machine

type and model information helps support technicians to identify the computer and provide faster service.

The machine type and model label is attached on the side of the computer as shown.

Figure 4. Machine type and model label

6M920t User Guide and Hardware Maintenance Manual

Chapter 2. Specifications

Power supply

• 180 watt automatic voltage-sensing power supply

• 250 watt automatic voltage-sensing power supply

• 400 watt automatic voltage-sensing power supply

Storage drives

Up to four SATA storage drives (including one hot-swap storage drive) and one M.2 storage drive

Video features

• The integrated graphics card supports the following:

– DisplayPort-out connector

– VGA-out connector

• The optional discrete graphics card provides an enhanced video experience and extended capabilities.

Audio features

• The integrated audio card supports the following:

– Audio line-out connector

– Headset connector

– Internal speaker

– Microphone connector

• The optional discrete audio card provides an enhanced audio experience and extended capabilities.

Input/Output (I/O) features

• Audio connectors (audio line-out connector, headset connector, and microphone connector)

• Card reader slot (optional)

• Display connectors (DisplayPort-out connector and VGA-out connector)

• Ethernet connector

• PS/2 keyboard connector (optional)

• PS/2 mouse connector (optional)

• Serial connector

• USB connectors

Expansion

• Card reader (optional)

• Memory slot

• Optical drive (optional)

• PCI Express card slot (physical link width x16; negotiable link width x4, x1)

• PCI Express x1 card slot

• PCI Express x16 graphics card slot

• Storage drive bay

Network features

• Ethernet LAN

• Wireless LAN (optional)

• Bluetooth (optional)

Physical dimensions

• Width: 165.0 mm (6.5 inches)

• Height: 410.3 mm (16.2 inches)

• Depth: 321.4 mm (12.7 inches)

Weight (without the package)

Maximum configuration as shipped: 10.0 kg (22.1 lb)

8M920t User Guide and Hardware Maintenance Manual

Chapter 3. Computer locks

This chapter provides instructions on how to lock your computer with the locking devices to keep your

computer safe.

Enabling or disabling the E-lock

Your computer may have a security lock solution installed to protect the computer from unauthorized

tampering of the internal components. Using the E-Lock, you can mechanically lock or unlock the computer

cover.

To enable or disable the E-Lock, do the following:

1. Turn on or restart the computer.

2. Before Windows starts up, repeatedly press and release the F1 or Fn+F1 key until the Setup Utility

program opens.

3. Click Security ➙ Electronic Lock to enable or disable the E-lock.

4. Press F10 or Fn+F10 to save the changes and reboot the computer.

Note: Changes do not take effect until the setting is saved and the system is rebooted.

Figure 5. Enabling or disabling the E-lock

Locking the computer cover

Locking the computer cover helps prevent unauthorized access to the inside of your computer. Your

computer features a padlock loop so that the computer cover cannot be removed when a padlock is

installed.

Figure 6. Locking the computer cover

10 M920t User Guide and Hardware Maintenance Manual

Attaching a Kensington-style cable lock

You can use a Kensington-style cable lock to secure your computer to a desk, table, or other nonpermanent

fixture. The cable lock connects to the security-lock slot at the rear of your computer. Depending on the type

selected, the cable lock can be operated with a key or combination. The cable lock also locks the buttons

used to open the computer cover. This is the same type of lock used with many notebook computers. You

can order such a cable lock directly from Lenovo by searching for Kensington at:

http://www.lenovo.com/support

Figure 7. Attaching a Kensington-style cable lock

Chapter 3.Computer locks 11

Attaching a cable lock

A cable lock can be used to secure devices, such as the keyboard and the mouse, by locking the device

cables to the computer. The cable lock connects to the cable-lock slots on the rear of the computer. To

install a cable lock, do the following:

1. Insert the clip 1 into the cable-lock slot 4.

2. Pull the cables you want to lock through the dents in the cable lock.

3. Press the clip 2 into the cable-lock slot 3 until it snaps into position.

Figure 8. Attaching a cable lock

12 M920t User Guide and Hardware Maintenance Manual

Chapter 4. Replacing hardware

This chapter provides instructions on how to replace hardware for your computer.

Before replacing hardware

Attention: Do not open your computer or attempt any repairs before reading this section and the Important

Product Information Guide.

Notes before replacing hardware

• Use computer components provided only by Lenovo.

• When installing or replacing an option, use the appropriate instructions explained in this manual along with

the instructions that come with the option.

• In most areas of the world, Lenovo requires the return of defective CRUs. Information about this will come

with the CRU or will come a few days after the CRU arrives.

Handling static-sensitive devices

Do not open the static-protective package containing the new part until the defective part has been removed

and you are ready to install the new part. Static electricity, although harmless to you, can seriously damage

computer components and options.

When you handle options and other computer components, take these precautions to avoid static-electricity

damage:

• Limit your movement. Movement can cause static electricity to build up around you.

• Always handle options and other computer components carefully. Handle PCI/PCIe cards, memory

modules, system boards, and microprocessors by the edges. Never touch any exposed circuitry.

• Prevent others from touching the options and other computer components.

• Touch the static-protective package containing the part to a metal expansion-slot cover or other

unpainted metal surface on the computer for at least two seconds. This reduces static electricity from the

package and your body before you install or replace a new part.

• When possible, remove the new part from the static-protective package, and install it directly in the

computer without setting the part down. When this is not possible, place the static-protective package on

a smooth, level surface and place the part on the package.

• Do not place the part on the computer cover or other metal surface.

Knowing FRUs (including CRUs)

• Field Replaceable Units (FRUs) are computer parts that a trained technician can upgrade or replace. FRUs

include all CRUs. For detailed FRU information, such as the FRU part numbers and supported computer

models, go to:

http://www.lenovo.com/serviceparts-lookup

• Customer Replaceable Units (CRUs) are computer parts that a user can upgrade or replace.

– Self-service CRUs: You can install self-service CRUs easily. These CRUs might be stand-alone,

latched, or secured by up to two screws. Examples of self-service CRUs include the keyboard, mouse,

any USB device. You are responsible for replacing all self-service CRUs.

– Optional-service CRUs: Handling optional-service CRUs requires some technical skills and simple tools

(such as a screwdriver). These CRUs are isolated parts within the computer. They are usually

concealed by an access panel that is secured by more than two screws. You must remove the screws

and panel to access the specific CRU. Optional-service CRUs can be removed and installed by users

or, during the warranty period, by a Lenovo service technician.

Before replacing FRUs

Before replacing any FRU, read the following:

• Only certified and trained personnel can service the computer.

• Before replacing an FRU, read the entire section about replacing the part.

• Be extremely careful during writing operations such as copying, saving, or formatting.

The sequence of the drives in the computer that you are servicing might have been altered. If you select

an incorrect drive, data or programs might be overwritten.

• Replace an FRU only with another FRU of the correct model.

When you replace an FRU, ensure that the model of the machine and the FRU part number are correct.

• An FRU should not be replaced because of a single, unreproducible failure.

Single failures can occur for a variety of reasons that have nothing to do with a hardware defect, such as

cosmic radiation, electrostatic discharge, or software errors. Consider replacing an FRU only when a

problem recurs. If you suspect that an FRU is defective, clear the error log and run the test again. If the

error does not recur, do not replace the FRU.

• Only replace a defective FRU.

Locating FRUs (including CRUs)

Notes:

• Some of the following components are optional.

• To replace a component that is not in the list below, contact a Lenovo service technician. For a list of

Lenovo Support phone numbers, go to:

http://www.lenovo.com/support/phone

14 M920t User Guide and Hardware Maintenance Manual

Figure 9. Locating FRUs (including CRUs)

Self-service CRUs Optional-service CRUs Non-CRUs

2 Coin-cell battery 29 Power supply assembly 1 Heat sink and fan assembly

4 Memory module 32 E-lock 3 Microprocessor

6 M.2 storage drive 36 Wi-Fi card shield 5 System board

8 Optical drive bracket 37 Wi-Fi card 7 Optical drive cable

9 Optical drive 11 Computer handle

Chapter 4.Replacing hardware 15

Self-service CRUs Optional-service CRUs Non-CRUs

10 Front access enclosure 13 Front I/O bracket

12 Front bezel 14 Card reader

19 Inner storage drive bracket 15 Power button

20 Outer storage drive bracket 16 Wi-Fi antennas and rear antenna

cover

21 2.5-inch or 3.5-inch storage drive 17 Thermal sensor

22 Storage drive converter 18 Illuminated red dot

23 Keyboard 26 Storage drive cable

24 Mouse 27 Front fan

25 Power cord 28 Internal speaker

30 PCI Express card 31 Chassis

34 M.2 storage drive bracket 33 Cover presence switch

38 Computer cover 35 Rear fan

Replacing the power cord

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Replace the power cord.

Figure 10. Removing the power cord

16 M920t User Guide and Hardware Maintenance Manual

Figure 11. Installing the power cord

Removing the computer cover

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

CAUTION:

Before you open the computer cover, turn off the computer and wait several minutes until the

computer is cool.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Unlock any locking device that secures the computer cover.

Chapter 4.Replacing hardware 17

3. Remove the computer cover.

Figure 12. Removing the computer cover

4. Complete the replacement. See “Completing the parts replacement” on page 68.

Replacing the front bezel

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 17.

3. Replace the front bezel.

18 M920t User Guide and Hardware Maintenance Manual

Figure 13. Removing the front bezel

Figure 14. Installing the front bezel

4. Complete the replacement. See “Completing the parts replacement” on page 68.

Pivoting the drive bay assembly upward and downward

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

Chapter 4.Replacing hardware 19

2. Remove the computer cover. See “Removing the computer cover” on page 17.

3. Remove the front bezel. See “Replacing the front bezel” on page 18.

4. Pivot the drive bay assembly upward and downward.

Figure 15. Pivoting the drive bay assembly upward

Figure 16. Pivoting the drive bay assembly downward

5. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 68.

Replacing the computer handle

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

20 M920t User Guide and Hardware Maintenance Manual

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 17.

3. Remove the front bezel. See “Replacing the front bezel” on page 18.

4. Replace the computer handle.

Figure 17. Removing the computer handle

Figure 18. Installing the computer handle

5. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 68.

Chapter 4.Replacing hardware 21

Replacing the optical drive

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 17.

3. Remove the front bezel. See “Replacing the front bezel” on page 18.

4. Disconnect the signal cable and the power cable from the optical drive.

5. Replace the optical drive.

Slim optical drive

Figure 19. Removing the optical drive

Figure 20. Removing the optical drive bracket

22 M920t User Guide and Hardware Maintenance Manual

Figure 21. Installing the optical drive bracket

Figure 22. Installing the optical drive

6. Connect the signal cable and the power cable to the new optical drive.

7. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 68.

Replacing the power button

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 17.

3. Remove the front bezel. See “Replacing the front bezel” on page 18.

4. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 19.

5. Disconnect the power button cable from the system board.

6. Replace the power button.

Chapter 4.Replacing hardware 23

Figure 23. Removing the power button

Figure 24. Installing the power button

7. Connect the new power button cable to the system board.

8. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 68.

Replacing the card reader

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 17.

3. Remove the front bezel. See “Replacing the front bezel” on page 18.

24 M920t User Guide and Hardware Maintenance Manual

4. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 19.

5. Disconnect the card reader cable from the system board.

6. Replace the card reader.

CAUTION:

Touch only the edges of the card reader. Do not touch the card reader’s circuit board.

Figure 25. Removing the card reader

Figure 26. Installing the card reader

7. Connect the new card reader cable to the system board.

8. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 68.

Chapter 4.Replacing hardware 25

Replacing the front I/O bracket

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 17.

3. Remove the front bezel. See “Replacing the front bezel” on page 18.

4. Replace the front I/O bracket.

Figure 27. Removing the front I/O bracket

Figure 28. Installing the front I/O bracket

26 M920t User Guide and Hardware Maintenance Manual

5. Connect the new front I/O bracket cable to the system board.

6. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 68.

Replacing the front fan

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 17.

3. Remove the front bezel. See “Replacing the front bezel” on page 18.

4. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 19.

5. Disconnect the front fan cable from the system board.

6. Replace the front fan.

Figure 29. Removing the front fan

Chapter 4.Replacing hardware 27

Figure 30. Installing the front fan

7. Connect the new front fan cable to the system board.

8. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 68.

Replacing the illuminated red dot

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 17.

3. Remove the front bezel. See “Replacing the front bezel” on page 18.

4. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 19.

5. Disconnect the illuminated red dot cable from the system board.

6. Replace the illuminated red dot.

28 M920t User Guide and Hardware Maintenance Manual

Figure 31. Removing the illuminated red dot

Figure 32. Installing the illuminated red dot

7. Connect the new illuminated red dot cable to the system board.

8. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 68.

Replacing the thermal sensor

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 17.

3. Remove the front bezel. See “Replacing the front bezel” on page 18.

Chapter 4.Replacing hardware 29

4. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 19.

5. Disconnect the thermal sensor cable from the system board.

6. Replace the thermal sensor.

Figure 33. Removing the thermal sensor

Figure 34. Installing the thermal sensor

7. Connect the new thermal sensor cable to the system board.

8. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 68.

Replacing the internal speaker

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

30 M920t User Guide and Hardware Maintenance Manual

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 17.

3. Remove the front bezel. See “Replacing the front bezel” on page 18.

4. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 19.

5. Disconnect the internal speaker cable from the system board.

6. Replace the internal speaker.

Figure 35. Removing the internal speaker

Figure 36. Installing the internal speaker

7. Connect the new internal speaker cable to the system board.

8. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 68.

Replacing the storage drive

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

Chapter 4.Replacing hardware 31

Replacing the 3.5-inch storage drive in the primary or secondary drive bay

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 17.

3. Remove the front bezel. See “Replacing the front bezel” on page 18.

4. If you are replacing the 3.5-inch storage drive in the secondary drive bay, pivot the drive bay assembly

outward. See “Pivoting the drive bay assembly upward and downward” on page 19.

5. Disconnect the signal cable and the power cable from the storage drive.

6. Replace the 3.5-inch storage drive.

• 3.5-inch storage drive in the primary storage drive bay

Figure 37. Removing the inner storage drive bracket

Figure 38. Removing the storage drive

32 M920t User Guide and Hardware Maintenance Manual

Figure 39. Installing the storage drive

Figure 40. Installing the inner storage drive bracket

• 3.5-inch storage drive in the secondary storage drive bay

Chapter 4.Replacing hardware 33

Figure 41. Removing the outer storage drive bracket

Figure 42. Removing the inner storage drive bracket

Figure 43. Removing the storage drive

34 M920t User Guide and Hardware Maintenance Manual

Figure 44. Installing the storage drive

Figure 45. Installing the inner storage drive bracket

Chapter 4.Replacing hardware 35

Figure 46. Installing the outer storage drive bracket

7. Connect the signal cable and the power cable to the new 3.5-inch storage drive.

8. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 68.

Replacing the 3.5-inch storage drive in the front-access storage enclosure

1. Replace the 3.5-inch storage drive in the front-access storage enclosure.

Figure 47. Opening the front-access storage enclosure

36 M920t User Guide and Hardware Maintenance Manual

Figure 48. Removing the inner storage drive bracket

Figure 49. Removing the storage drive

Chapter 4.Replacing hardware 37

Figure 50. Installing the storage drive

Figure 51. Installing the inner storage drive bracket

38 M920t User Guide and Hardware Maintenance Manual

Figure 52. Installing the front-access storage enclosure

Replacing the 2.5-inch storage drive in the storage converter

1. Remove the storage converter with the 2.5-inch storage drive. See “Replacing the 3.5-inch storage drive

in the primary or secondary drive bay” or "Replacing the 3.5-inch storage drive in the front-access

storage enclosure".

2. Replace the 2.5-inch storage drive in the storage converter.

Figure 53. Removing the storage drive

Chapter 4.Replacing hardware 39

Figure 54. Installing the storage drive

3. Reinstall the storage converter with the 2.5-inch storage drive. See “Replacing the 3.5-inch storage drive

in the primary or secondary drive bay” or "Replacing the 3.5-inch storage drive in the front-access

storage enclosure".

Replacing the 2.5-inch storage drive in the tertiary drive bay

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 17.

3. Remove the front bezel. See “Replacing the front bezel” on page 18.

4. If you are replacing the 3.5-inch storage drive in the secondary drive bay, pivot the drive bay assembly

outward. See “Pivoting the drive bay assembly upward and downward” on page 19.

5. Disconnect the signal cable and the power cable from the storage drive.

6. Replace the 2.5-inch storage drive in the tertiary drive bay.

Figure 55. Removing the outer storage drive bracket

40 M920t User Guide and Hardware Maintenance Manual

Figure 56. Removing the inner storage drive bracket

Figure 57. Removing the storage drive

Chapter 4.Replacing hardware 41

Figure 58. Installing the storage drive

Figure 59. Installing the inner storage drive bracket

42 M920t User Guide and Hardware Maintenance Manual

Figure 60. Installing the outer storage drive bracket

7. Connect the signal cable and the power cable to the new 2.5-inch storage drive.

8. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 68.

Replacing the memory module

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

Ensure that you follow the order of installing memory modules shown in the following figure.

Figure 61. The order of installing memory modules

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

Chapter 4.Replacing hardware 43

2. Remove the computer cover. See “Removing the computer cover” on page 17.

3. Remove the front bezel. See “Replacing the front bezel” on page 18.

4. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 19.

5. Replace the memory module.

Figure 62. Removing the memory module

Figure 63. Installing the memory module

6. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 68.

Replacing the coin-cell battery

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

Your computer has a special type of memory that maintains the date, time, and settings for built-in features,

such as parallel connector assignments (configurations). A coin-cell battery keeps this information active

when you turn off the computer.

The coin-cell battery normally requires no charging or maintenance throughout its life; however, no coin-cell

battery lasts forever. If the coin-cell battery fails, the date, time, and configuration information (including

passwords) are lost. An error message is displayed when you turn on the computer.

To replace the coin-cell battery,

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

44 M920t User Guide and Hardware Maintenance Manual

2. Remove the computer cover. See “Removing the computer cover” on page 17.

3. Remove the front bezel. See “Replacing the front bezel” on page 18.

4. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 19.

5. Replace the coin-cell battery.

Figure 64. Removing the coin-cell battery

Figure 65. Removing the coin-cell battery

Figure 66. Installing the coin-cell battery

Figure 67. Installing the coin-cell battery

6. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 68.

To dispose of the coin-cell battery, refer to Lithium coin-cell battery notice in the Safety and Warranty Guide.

Chapter 4.Replacing hardware 45

Replacing a PCI Express card

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 17.

3. Remove the front bezel. See “Replacing the front bezel” on page 18.

4. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 19.

5. Replace a PCI Express card.

Figure 68. Removing a PCI Express card

Note: If the card is held in place by a retaining latch, press the latch 1 as shown to disengage the latch.

Then, gently remove the card from the slot.

46 M920t User Guide and Hardware Maintenance Manual

Figure 69. Installing a PCI Express card

6. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 68.

Replacing the M.2 storage drive

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 17.

3. Remove the front bezel. See “Replacing the front bezel” on page 18.

4. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 19.

5. Replace the M.2 storage drive.

• Type 1

Figure 70. Pulling out the plastic fastener

Chapter 4.Replacing hardware 47

Figure 71. Removing the optical drive retainer

Figure 72. Installing the optical drive retainer

Figure 73. Installing the optical drive

• Type 2

48 M920t User Guide and Hardware Maintenance Manual

Figure 74. Pulling out the plastic fastener

Figure 75. Removing the optical drive bracket

Figure 76. Installing the optical drive bracket

Chapter 4.Replacing hardware 49

Figure 77. Installing the optical drive

6. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 68.

Replacing the M.2 storage drive bracket

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 17.

3. Remove the front bezel. See “Replacing the front bezel” on page 18.

4. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 19.

5. Remove the M.2 storage drive.

6. Replace the M.2 storage drive bracket.

Figure 78. Removing the M.2 storage drive bracket

50 M920t User Guide and Hardware Maintenance Manual

Figure 79. Installing the M.2 storage drive bracket

7. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 68.

Replacing the Wi-Fi card

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 17.

3. Remove the front bezel. See “Replacing the front bezel” on page 18.

4. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 19.

5. Replace the Wi-Fi card.

• Type 1

Figure 80. Removing the Wi-Fi card shield

Chapter 4.Replacing hardware 51

Figure 81. Disconnecting the antennas

Figure 82. Removing the Wi-Fi card

Figure 83. Installing the Wi-Fi card

52 M920t User Guide and Hardware Maintenance Manual

Figure 84. Connecting the antennas

Figure 85. Installing the Wi-Fi card shield

• Type 2

Figure 86. Removing the Wi-Fi card shield

Chapter 4.Replacing hardware 53

Figure 87. Disconnecting the antennas

Figure 88. Removing the Wi-Fi card

Figure 89. Installing the Wi-Fi card

Figure 90. Connecting the antennas

54 M920t User Guide and Hardware Maintenance Manual

Figure 91. Installing the Wi-Fi card shield

6. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 68.

Replacing the Wi-Fi antennas

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 17.

3. Remove the front bezel. See “Replacing the front bezel” on page 18.

4. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 19.

5. Disconnect the antenna cables from the Wi-Fi card.

6. Replace the Wi-Fi antennas.

• Front Wi-Fi antenna

Chapter 4.Replacing hardware 55

Figure 92. Removing the Wi-Fi antenna

Figure 93. Installing the Wi-Fi antenna

• Rear Wi-Fi antenna

56 M920t User Guide and Hardware Maintenance Manual

Figure 94. Removing the rear Wi-Fi antenna cover

Figure 95. Removing the Wi-Fi antenna

Chapter 4.Replacing hardware 57

Figure 96. Installing the Wi-Fi antenna

Figure 97. Installing the rear Wi-Fi antenna cover

7. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 68.

Replacing the heat sink and fan assembly

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

CAUTION:

The heat sink and fan assembly might be very hot. Before you open the computer cover, turn off the

computer and wait several minutes until the computer is cool.

58 M920t User Guide and Hardware Maintenance Manual

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 17.

3. Remove the front bezel. See “Replacing the front bezel” on page 18.

4. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 19.

5. Disconnect the heat sink and fan assembly cable from the system board.

6. Replace the heat sink and fan assembly.

Figure 98. Removing the heat sink and fan assembly

Figure 99. Installing the heat sink and fan assembly

7. Connect the new heat sink and fan assembly cable to the system board.

8. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 68.

Replacing the power supply assembly

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

Chapter 4.Replacing hardware 59

Although there are no moving parts in your computer after the power cord has been disconnected, the

following warnings are required for your safety and proper Underwriters Laboratories (UL) certification.

CAUTION:

Never remove the cover on a power supply or any part that has the following label attached.

Hazardous voltage, current, and energy levels are present inside any component that has this label

attached. There are no serviceable parts inside these components. If you suspect a problem with one

of these parts, contact a service technician.

1. Remove the computer cover. See “Removing the computer cover” on page 17.

2. Remove the front bezel. See “Replacing the front bezel” on page 18.

3. Remove the optical drive. See “Replacing the optical drive” on page 22.

4. Remove the storage drive bracket. See “Replacing the storage drive” on page 31.

5. Disconnect the power supply assembly cable from the system board.

6. Replace the power supply assembly.

Figure 100. Removing the power supply assembly

60 M920t User Guide and Hardware Maintenance Manual

Figure 101. Installing the power supply assembly

7. Connect the new power supply assembly cable to the system board.

8. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 68.

Replacing the microprocessor

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

CAUTION:

The heat sink and microprocessor might be very hot. Before you open the computer cover, turn off the

computer and wait several minutes until the computer is cool.

1. Remove the computer cover. See “Removing the computer cover” on page 17.

2. Remove the front bezel. See “Replacing the front bezel” on page 18.

3. Pivot the drive bay assembly outward. See “Pivoting the drive bay assembly upward and downward” on

page 19.

4. Remove the heat sink and fan assembly. See “Replacing the heat sink and fan assembly” on page 58.

5. Disconnect all cables connected to the system board.

6. Replace the microprocessor.

Notes:

• Your microprocessor and socket might look different from the one illustrated.

• Touch only the edges of the microprocessor. Do not touch the gold contacts on the bottom.

• Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be

kept as clean as possible.

Chapter 4.Replacing hardware 61

Figure 102. Releasing the holder

Figure 103. Pivoting up the socket

Figure 104. Removing the microprocessor

Figure 105. Installing the microprocessor

62 M920t User Guide and Hardware Maintenance Manual

Figure 106. Pivoting the socket downward

Figure 107. Securing the holder

7. Reconnect all cables that were disconnected from the system board.

8. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 68.

Replacing the E-lock

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

Note: To remove the screws, you need a special tool (T15 star wrench).

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 17.

3. Disconnect the E-lock cable from the system board.

4. Replace the E-lock.

Chapter 4.Replacing hardware 63

Figure 108. Removing the E-lock

Figure 109. Installing the E-lock

5. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 68.

Replacing the cover presence switch

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 17.

3. Remove the front bezel. See “Replacing the front bezel” on page 18.

4. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 19.

5. Disconnect the cover presence switch cable from the system board.

6. Replace the cover presence switch.

64 M920t User Guide and Hardware Maintenance Manual

Figure 110. Removing the cover presence switch

Figure 111. Installing the cover presence switch

7. Connect the new cover presence switch cable to the system board.

8. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 68.

Replacing the rear fan

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 17.

3. Remove the front bezel. See “Replacing the front bezel” on page 18.

Chapter 4.Replacing hardware 65

4. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 19.

5. Disconnect the rear fan cable from the system board.

6. Replace the rear fan.

Figure 112. Removing the rear fan

Figure 113. Installing the rear fan

7. Connect the new rear fan cable to the system board.

8. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 68.

66 M920t User Guide and Hardware Maintenance Manual

Replacing the system board

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 17.

3. Remove the front bezel. See “Replacing the front bezel” on page 18.

4. Remove the power button. See “Replacing the power button” on page 23.

5. Remove the front I/O bracket. See “Replacing the front I/O bracket” on page 26.

6. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 19.

7. Remove all memory modules. See “Replacing the memory module” on page 43.

8. Remove the heat sink and fan assembly. See “Replacing the heat sink and fan assembly” on page 58.

9. Remove the microprocessor. See “Replacing the microprocessor” on page 61.

10. Remove all PCI Express cards. See “Replacing a PCI Express card” on page 46.

11. Remove the Wi-Fi card. See “Replacing the Wi-Fi card” on page 51.

12. Remove the M.2 storage drive. See “Replacing the M.2 storage drive” on page 47.

13. Record the cable routing and cable connections, and then disconnect all cables from the system board.

See “System board” on page 5.

Chapter 4.Replacing hardware 67

14. Replace the system board.

Notes:

• The numbers in the following figure show the locations of the screws instead of the removing and

reinstalling order of the screws.

• Handle the system board carefully by its edges.

Figure 114. Removing the system board

15. Route all the cables that you disconnected from the failing system board, and then reconnect the cables

to the new system board. See “System board” on page 5.

16. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 68.

Completing the parts replacement

After completing the installation or replacement for all parts, reinstall the computer cover and reconnect the

cables.

To reinstall the computer cover and reconnect the cables to your computer, do the following:

1. Ensure that all components have been reassembled correctly and that no tools or loose screws are left

inside your computer.

2. Ensure that the cables are routed correctly before reinstalling the computer cover. Keep cables clear of

the hinges and sides of the computer chassis to avoid interference when reinstalling the computer

cover.

68 M920t User Guide and Hardware Maintenance Manual

3. Reinstall the computer cover.

Figure 115. Reinstalling the computer cover

4. Place the computer in an upright position.

5. If a locking device is available, use it to lock the computer.

6. Reconnect the external cables and power cords to the corresponding connectors on the computer.

Chapter 4.Replacing hardware 69

70 M920t User Guide and Hardware Maintenance Manual

Appendix A. Notices

Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult

your local Lenovo representative for information on the products and services currently available in your

area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that

Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service

that does not infringe any Lenovo intellectual property right may be used instead. However, it is the user's

responsibility to evaluate and verify the operation of any other product, program, or service.

Lenovo may have patents or pending patent applications covering subject matter described in this

document. The furnishing of this document does not give you any license to these patents. You can send

license inquiries, in writing, to:

Lenovo (United States), Inc.

1009 Think Place - Building One

Morrisville, NC 27560

U.S.A.

Attention: Lenovo Director of Licensing

LENOVO PROVIDES THIS PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS

OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow

disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply to

you.

This information could include technical inaccuracies or typographical errors. Changes are periodically made

to the information herein; these changes will be incorporated in new editions of the publication. Lenovo may

make improvements and/or changes in the products and/or the programs described in this publication at any

time without notice.

The products described in this document are not intended for use in implantation or other life support

applications where malfunction may result in injury or death to persons. The information contained in this

document does not affect or change Lenovo product specifications or warranties. Nothing in this document

shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo or

third parties. All information contained in this document was obtained in specific environments and is

presented as an illustration. The result obtained in other operating environments may vary.

Lenovo may use or distribute any of the information you supply in any way it believes appropriate without

incurring any obligation to you.

Any references in this publication to non-Lenovo Web sites are provided for convenience only and do not in

any manner serve as an endorsement of those Web sites. The materials at those Web sites are not part of the

materials for this Lenovo product, and use of those Web sites is at your own risk.

Any performance data contained herein was determined in a controlled environment. Therefore, the result

obtained in other operating environments may vary significantly. Some measurements may have been made

on development-level systems and there is no guarantee that these measurements will be the same on

generally available systems. Furthermore, some measurements may have been estimated through

extrapolation. Actual results may vary. Users of this document should verify the applicable data for their

specific environment.

72 M920t User Guide and Hardware Maintenance Manual

Appendix B. Trademarks

The following terms are trademarks of Lenovo in the United States, other countries, or both:

Lenovo

The Lenovo logo

DisplayPort and Mini DisplayPort are trademarks of the Video Electronics Standards Association.

The terms HDMI and HDMI High-Definition Multimedia Interface are trademarks or registered trademarks of

HDMI Licensing LLC in the United States and other countries.

Other company, product, or service names may be trademarks or service marks of others.

74 M920t User Guide and Hardware Maintenance Manual

Table of Contents

Lenovo M920 User Manual

Related Manuals