Table of Contents
- About this documentation
- Chapter 1. Meet your computer
- Chapter 2. Get started with your computer
- Chapter 3. Explore your computer
- Chapter 4. Accessories
- Chapter 5. Secure your computer and information
- Chapter 6. Configure advanced settings
- Chapter 7. CRU replacement
- Chapter 8. Help and support
- Appendix A. Important safety information
- Appendix B. Accessibility and ergonomic information
- Appendix C. Supplemental information about the Linux operating system
- Appendix D. Compliance and TCO Certified information
- Appendix E. Notices and trademarks
Lenovo X13 User Manual
Displayed below is the user manual for X13 by Lenovo which is a product in the Notebooks category. This manual has pages.
Related Manuals
T14s Gen 1 and X13 Gen 1
User Guide
Read this first
Before using this documentation and the product it supports, ensure that you read and understand the
following:
• Appendix A “Important safety information” on page 71
• Safety and Warranty Guide
• Setup Guide
Third Edition (May 2021)
© Copyright Lenovo 2020, 2021.
LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant to a General Services
Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-
35F-05925.
Contents
About this documentation . . . . . . . . iii
Chapter 1. Meet your computer . . . . . 1
Front . . . . . . . . . . . . . . . . . . . . 1
Base . . . . . . . . . . . . . . . . . . . . 3
Left . . . . . . . . . . . . . . . . . . . . 5
Right . . . . . . . . . . . . . . . . . . . . 8
Rear . . . . . . . . . . . . . . . . . . . . 9
Bottom . . . . . . . . . . . . . . . . . . 10
Features and specifications . . . . . . . . . . 11
Statement on USB transfer rate . . . . . . . 12
Chapter 2. Get started with your
computer . . . . . . . . . . . . . . . . 13
Connect to networks . . . . . . . . . . . . . 13
Connect to the wired Ethernet . . . . . . . 13
Connect to Wi-Fi networks. . . . . . . . . 13
Connect to a cellular network (for selected
models) . . . . . . . . . . . . . . . . 13
Use the Vantage app . . . . . . . . . . . . . 14
Use Lenovo Quick Clean . . . . . . . . . . . 14
Interact with your computer . . . . . . . . . . 15
Use the keyboard shortcuts . . . . . . . . 16
Use the TrackPoint pointing device . . . . . 18
Use the trackpad . . . . . . . . . . . . 19
Use the multi-touch screen (for selected
models) . . . . . . . . . . . . . . . . 21
Use privacy protection (for selected
models) . . . . . . . . . . . . . . . . 23
Use the Intelligent Cooling feature (for
selected models) . . . . . . . . . . . . 24
Use multimedia . . . . . . . . . . . . . . . 24
Use audio . . . . . . . . . . . . . . . 24
Connect to an external display . . . . . . . 25
Chapter 3. Explore your computer . . 27
Manage power . . . . . . . . . . . . . . . 27
Check the battery status . . . . . . . . . 27
Charge the computer . . . . . . . . . . . 27
Maximize the battery life . . . . . . . . . 28
Set power button behaviors . . . . . . . . 29
Set the power plan . . . . . . . . . . . . 29
Transfer data . . . . . . . . . . . . . . . . 29
Set up a Bluetooth connection . . . . . . . 29
Set up an NFC connection (for selected Intel
models) . . . . . . . . . . . . . . . . 29
Use a microSD card (for selected models). . . 30
Use a smart card (for selected models) . . . . 31
Turn on the Airplane mode . . . . . . . . . . 31
Use the factory color calibration feature (for
selected models) . . . . . . . . . . . . . . 32
Chapter 4. Accessories . . . . . . . . 33
Purchase options . . . . . . . . . . . . . . 33
Docking station . . . . . . . . . . . . . . . 33
Front view . . . . . . . . . . . . . . . 34
Rear view . . . . . . . . . . . . . . . 35
Attach a docking station. . . . . . . . . . 36
Detach a docking station . . . . . . . . . 37
Connect multiple external displays . . . . . 38
Chapter 5. Secure your computer
and information . . . . . . . . . . . . 39
Lock the computer . . . . . . . . . . . . . 39
Use passwords . . . . . . . . . . . . . . . 39
Password types . . . . . . . . . . . . . 39
Set, change, and remove a password . . . . 41
Use Power Loss Protection function (for selected
models) . . . . . . . . . . . . . . . . . . 42
Use the fingerprint reader (for selected models) . . 42
Use face authentication (for selected models) . . . 43
Use firewalls and antivirus programs. . . . . . . 43
Chapter 6. Configure advanced
settings. . . . . . . . . . . . . . . . . 45
UEFI BIOS . . . . . . . . . . . . . . . . . 45
What is UEFI BIOS . . . . . . . . . . . . 45
Enter the UEFI BIOS menu . . . . . . . . . 45
Navigate in the UEFI BIOS interface . . . . . 45
Change the startup sequence . . . . . . . 45
Set the system date and time. . . . . . . . 46
Update UEFI BIOS . . . . . . . . . . . . 46
Install a Windows operating system and drivers . . 46
Chapter 7. CRU replacement . . . . . 49
What are CRUs . . . . . . . . . . . . . . . 49
Disable Fast Startup and the built-in battery. . . . 49
Replace a CRU . . . . . . . . . . . . . . . 50
Base cover assembly . . . . . . . . . . . 50
M.2 solid-state drive . . . . . . . . . . . 51
Wireless WAN card (for selected models) . . . 54
Keyboard (for ThinkPad X13 Gen 1) . . . . . 56
Chapter 8. Help and support . . . . . 63
Frequently asked questions . . . . . . . . . . 63
Error messages . . . . . . . . . . . . . . . 64
© Copyright Lenovo 2020, 2021 i
Beep errors . . . . . . . . . . . . . . . . 65
Self-help resources . . . . . . . . . . . . . 66
Windows label . . . . . . . . . . . . . . . 67
Call Lenovo . . . . . . . . . . . . . . . . 67
Before you contact Lenovo . . . . . . . . 67
Lenovo Customer Support Center . . . . . . 68
Purchase additional services. . . . . . . . . . 69
Appendix A. Important safety
information . . . . . . . . . . . . . . . 71
Appendix B. Accessibility and
ergonomic information . . . . . . . . 85
Appendix C. Supplemental
information about the Linux operating
system . . . . . . . . . . . . . . . . . 87
Appendix D. Compliance and TCO
Certified information . . . . . . . . . . 89
Appendix E. Notices and
trademarks . . . . . . . . . . . . . . . 103
ii T14s Gen 1 and X13 Gen 1 User Guide
About this documentation
• Illustrations in this documentation might look different from your product.
• Depending on the model, some optional accessories, features, and software programs might not be
available on your computer.
• Depending on the version of operating systems and programs, some user interface instructions might not
be applicable to your computer.
• Documentation content is subject to change without notice. Lenovo makes constant improvements on the
documentation of your computer, including this User Guide. To get the latest documentation, go to https://
pcsupport.lenovo.com.
• Microsoft® makes periodic feature changes to the Windows® operating system through Windows Update.
As a result, some information in this documentation might become outdated. Refer to Microsoft resources
for the latest information.
© Copyright Lenovo 2020, 2021 iii
iv T14s Gen 1 and X13 Gen 1 User Guide
Chapter 1. Meet your computer
ThinkPad T14s Gen 1 and ThinkPad X13 Gen 1 might be shipped with different microprocessors, namely
Intel® and Advanced Micro Devices (AMD). Hereby Intel models and AMD models are used to distinguish
computer models with different microprocessors.
Front
1. Infrared LED*
Emit infrared (IR) light.
Note: Do not block the IR light-emitting diode (LED). Otherwise, the IR function
might not work.
2. Camera with IR function*
• Log in to your computer with face authentication. See “Use face authentication
(for selected models)” on page 43.
• Take pictures or record videos by clicking Camera from the Start menu. The
indicator next to the camera is on when the camera is in use.
If you use other apps that support photographing, video chatting, and video
conference, the camera starts automatically when you enable the camera-
required feature from the app.
3. ThinkShutter* Slide ThinkShutter to cover or uncover the camera lens. It is designed to protect
your privacy.
4. Microphones* Capture or record sound.
© Copyright Lenovo 2020, 2021 1
5. Camera*
Take pictures or record videos by clicking Camera from the Start menu. The
indicator next to the camera is on when the camera is in use.
If you use other apps that support photographing, video chatting, and video
conference, the camera starts automatically when you enable the camera-
required feature from the app.
6. Multi-touch screen* Enable you to use your computer with simple touch gestures. See “Use the multi-
touch screen (for selected models)” on page 21.
* for selected models
2T14s Gen 1 and X13 Gen 1 User Guide
1. Power button
Press to turn on the computer or put the computer to sleep mode.
To turn off the computer, open the Start menu, click Power, and then select
Shut down.
The indicator in the power button shows the system status of your computer.
• Blinking for three times: The computer is initially connected to power.
• On: The computer is on.
• Off: The computer is off or in hibernation mode.
• Blinking rapidly: The computer is entering sleep or hibernation mode.
• Blinking slowly: The computer is in sleep mode.
2. Fingerprint reader* Log in to your computer with enrolled fingerprints. See “Use the fingerprint reader
(for selected models)” on page 42.
3. NFC label (for selected Intel
models)
Your computer supports NFC (near field communication). You can share
information with another NFC-enabled device. See “Set up an NFC connection
(for selected Intel models)” on page 29.
4. Trackpad Perform finger touch and all the functions of a traditional mouse. See “Use the
trackpad” on page 19.
5. NFC mark (for selected Intel
models)
Your computer supports NFC (near field communication). You can share
information with another NFC-enabled device. See “Set up an NFC connection
(for selected Intel models)” on page 29.
6. TrackPoint® pointing device Perform all the functions of a traditional mouse. See “Use the TrackPoint pointing
device” on page 18.
* for selected models
4T14s Gen 1 and X13 Gen 1 User Guide
1. USB-C™ (3.2 Gen 1)
connector (for Intel models) • Charge your computer.
• Charge USB-C compatible devices with the output voltage and current of 5 V
and 1.5 A.
• Transfer data at USB 3.2 speed, up to 5 Gbps.
• Connect to an external display:
– USB-C to VGA: 1920 x 1200 pixels, 60 Hz
– USB-C to DP: 4096 x 2304 pixels, 60 Hz
• Connect to USB-C accessories to help expand your computer functionality. To
purchase USB-C accessories, go to https://www.lenovo.com/accessories.
• Supply power to another computer using P-to-P (Peer to Peer) 2.0 charging
function. See “Use P-to-P 2.0 charging function” on page 27.
Note: When the battery power is below 10%, the connected USB-C accessories
might not work correctly.
2. USB-C (3.2 Gen 2) connectors
(for AMD models) • Charge your computer.
• Charge USB-C compatible devices with the output voltage and current of 5 V
and 1.5 A.
• Transfer data at USB 3.2 speed, up to 10 Gbps.
• Connect to an external display:
– USB-C to VGA: 1920 x 1200 pixels, 60 Hz
– USB-C to DP: 4096 x 2304 pixels, 60 Hz
• Connect to USB-C accessories to help expand your computer functionality. To
purchase USB-C accessories, go to https://www.lenovo.com/accessories.
• Supply power to another computer using P-to-P (Peer to Peer) 2.0 charging
function. See “Use P-to-P 2.0 charging function” on page 27.
Note: When the battery power is below 10%, the connected USB-C accessories
might not work correctly.
3. Thunderbolt™ 3 connector
(USB-C) (for Intel models) • Charge your computer.
• Charge USB-C compatible devices with the output voltage and current of 5 V
and 1.5 A.
• Transfer data at Thunderbolt 3 speed, up to 20 Gbps.
• Connect to an external display:
– USB-C to VGA: 1920 x 1200 pixels, 60 Hz
– USB-C to DP: 4096 x 2304 pixels, 60 Hz
• Connect to USB-C accessories to help expand your computer functionality. To
purchase USB-C accessories, go to https://www.lenovo.com/accessories.
• Supply power to another computer using P-to-P (Peer to Peer) 2.0 charging
function. See “Use P-to-P 2.0 charging function” on page 27.
Note: When the battery power is below 10%, the connected USB-C accessories
might not work correctly.
6T14s Gen 1 and X13 Gen 1 User Guide
4. Ethernet extension connector
Gen 2
Make your computer thinner than the ones with a standard Ethernet connector.
Use a ThinkPad Ethernet Extension Adapter Gen 2 to connect your computer to a
local area network (LAN) through this connector. The ThinkPad Ethernet Extension
Adapter Gen 2 is available as an option and shipped with some computer models
only. You can purchase a ThinkPad Ethernet Extension Adapter Gen 2 from
Lenovo at: https://www.lenovo.com/accessories.
Note: The Ethernet extension connector Gen 2 and the adjoining Thunderbolt 3
connector (USB-C) or USB-C (3.2 Gen 2) connector cannot be used
simultaneously.
5. Docking-station connector Connect the computer to one of the following supported docks to extend the
computer capabilities:
• ThinkPad Basic Docking Station
• ThinkPad Pro Docking Station
• ThinkPad Ultra Docking Station
6. USB 3.2 connector Gen 1 Connect a USB-compatible device, such as a USB keyboard, USB mouse, USB
storage device, or USB printer.
7. HDMI™ connector For Intel models, the HDMI connector supports the HDMI 1.4 standard. Connect
to a compatible digital audio device or video monitor, such as an HDTV.
For AMD models, the HDMI connector on your computer supports the HDMI 2.0
standard by default. If you connect an external display to your computer through
the HDMI connector with an HDMI 1.4 cable, the external display might not work.
In this case, do one of the following:
• Use a qualified HDMI 2.0 cable.
• Change the HDMI standard of the HDMI connector from 2.0 to 1.4. To change
the HDMI standard, enter the UEFI BIOS menu (see “Enter the UEFI BIOS
menu” on page 45), and then configure HDMI Mode Select in the Config
menu.
8. Audio connector • Connect headphones with a 3.5-mm (0.14-inch) and 4-pole plug to listen to the
sound from the computer.
• Connect a headset with a 3.5-mm (0.14-inch) and 4-pole plug to listen to the
sound from the computer or talk with others.
Note: This connector does not support standalone external microphones.
Chapter 1.Meet your computer 7
Right
1. Smart-card slot*
Use smart cards for authentication, data storage, and application processing.
Within large organizations, you might also use smart cards for strong security
authentication of single sign-on (SSO). See “Use a smart card (for selected
models)” on page 31.
2. Always On USB 3.2 connector
Gen 1
With the Always On USB feature enabled, the Always On USB 3.2 connector Gen
1 can charge a USB-compatible device when the computer is on, off, in sleep
mode, or in hibernation mode.
Notes:
• By default, Always On USB is enabled and Charge in Battery Mode is
disabled in UEFI BIOS.
• When the computer is off or in hibernation mode, and Charge in Battery Mode
is disabled in UEFI BIOS, ensure that you have connected the computer to ac
power.
To enable the Always On USB feature:
1. Enter the UEFI BIOS menu. See “Enter the UEFI BIOS menu” on page 45.
2. Click Config ➙ USB ➙ Always On USB to enable the Always On USB
feature.
3. Security-lock slot Lock your computer to a desk, table, or other fixtures through a compatible
security cable lock. See “Lock the computer” on page 39.
* for selected models
8T14s Gen 1 and X13 Gen 1 User Guide
Rear
1. System status indicator
The indicator in the ThinkPad logo on the computer lid shows the system status of
your computer.
• Blinking for three times: The computer is initially connected to power.
• On: The computer is on.
• Off: The computer is off or in hibernation mode.
• Blinking rapidly: The computer is entering sleep or hibernation mode.
• Blinking slowly: The computer is in sleep mode.
2. Nano-SIM-card and microSD-
card slot*
Use the Nano Subscriber Identity Module (SIM) card to connect to a wireless-
WAN network. See “Connect to a cellular network (for selected models)” on page
13. Use the microSD card to transfer or store files. See “Use a microSD card (for
selected models)” on page 30.
* for selected models
Chapter 1.Meet your computer 9
Bottom
ThinkPad T14s Gen 1
ThinkPad X13 Gen 1
1. Docking-station hook holes Use the docking-station hook holes to secure a supported docking station.
2. Emergency-reset hole
If the computer stops responding and you cannot turn it off by pressing the power
button, reset your computer:
1. Disconnect your computer from ac power.
2. Insert a straightened paper clip into the hole to cut off power supply
temporarily.
3. Connect your computer to ac power and then turn on your computer.
3. Speakers Enable you to experience high-quality sound.
10 T14s Gen 1 and X13 Gen 1 User Guide
Features and specifications
Dimensions
ThinkPad T14s Gen 1
• Width: 328.8 mm to 329.15 mm (12.94 inches to 12.95 inches)
• Depth: 225.8 mm to 226.45 mm (8.89 inches to 8.91 inches)
• Thickness: 16.1 mm to 17.2 mm (0.63 inches to 0.68 inches)
ThinkPad X13 Gen 1
• Width: 312 mm (12.28 inches)
• Depth: 217.2 mm (8.55 inches)
• Thickness: 16.5 mm to 16.9 mm (0.65 inches to 0.67 inches)
Maximum heat output
(depending on the model)
• 45 W (154 Btu/hr)
• 65 W (222 Btu/hr)
Power source (ac power
adapter)
• Sine-wave input at 50 Hz to 60 Hz
• Input rating of the ac power adapter: 100 V to 240 V ac, 50 Hz to 60 Hz
Microprocessor To view the microprocessor information of your computer, right-click the Start
button and then click System.
Memory Double data rate 4 (DDR4) onboard memory module
Note: Depending on the system configuration, memory speeds might vary.
Storage device
• M.2 solid-state drive*
• Hybrid solid-state drive (with Intel® Optane™ memory) (for selected Intel
models)
Display
• Brightness control
• Color display with Thin Film Transistor (TFT) technology
• Color display with In-Plane Switching (IPS) technology (for ThinkPad T14s Gen
1)
• Color display with In-Plane Switching (IPS) technology or Twisted Nematic (TN)
technology (for ThinkPad X13 Gen 1)
• Display size:
– ThinkPad T14s Gen 1: 355.6 mm (14 inches)
– ThinkPad X13 Gen 1: 337.82 mm (13.3 inches)
• Display resolution:
– ThinkPad T14s Gen 1 (for Intel models): 1920 x 1080 pixels or 3840 x 2160
pixels
– ThinkPad T14s Gen 1 (for AMD models): 1920 x 1080 pixels
– ThinkPad X13 Gen 1: 1366 x 768 pixels or 1920 x 1080 pixels
• Multi-touch technology*
• PrivacyGuard feature*
Keyboard
• Function keys
• Six-row keyboard or six-row keyboard with backlight
• Trackpad
• TrackPoint pointing device
Chapter 1.Meet your computer 11
Connectors and slots
• Audio connector
• Ethernet extension connector Gen 2
• HDMI connector
• Nano-SIM-card and microSD-card slot*
• One Always on USB 3.2 connector Gen 1
• One USB 3.2 connector Gen 1
• One USB-C (3.2 Gen 1) connector (for Intel models)
• One Thunderbolt 3 connector (USB-C) (for Intel models)
• Smart-card slot*
• Two USB-C (3.2 Gen 2) connectors (for AMD models)
Security features
• Face authentication*
• Fingerprint reader*
• Password
• ThinkShutter*
• Security-lock slot
• Trusted Platform Module (TPM)*
Wireless features
• Bluetooth
• Global Positioning System (GPS) satellite receiver (available on models with
wireless WAN)*
• Near field communication (NFC)*
• Wireless LAN
• Wireless WAN*
Others • Camera*
• Microphones*
* for selected models
Statement on USB transfer rate
Depending on many factors such as the processing capability of the host and peripheral devices, file
attributes, and other factors related to system configuration and operating environments, the actual transfer
rate using the various USB connectors on this device will vary and will be slower than the data rate listed
below for each corresponding device.
USB device Data rate (Gbit/s)
3.2 Gen 1 / 3.1 Gen 1 5
3.2 Gen 2 / 3.1 Gen 2 10
3.2 Gen 2 × 2 20
Thunderbolt 3 40
Thunderbolt 4 40
12 T14s Gen 1 and X13 Gen 1 User Guide
Chapter 2. Get started with your computer
Connect to networks
Your computer helps you connect to the world through a wired or wireless network.
Connect to the wired Ethernet
Connect your computer to a local network through the Ethernet extension connector Gen 2 on your
computer with a ThinkPad Ethernet Extension Adapter Gen 2.
The Ethernet extension adapter is available as an option and shipped with some computer models. You can
purchase one from Lenovo at https://www.lenovo.com/accessories.
Note: The Ethernet extension connector Gen 2 and the adjoining Thunderbolt 3 connector (USB-C) or USB-
C (3.2 Gen 2) connector cannot be used simultaneously.
Connect to Wi-Fi networks
Click the network icon in the Windows® notification area, and then select a network for connection. Provide
required information, if needed.
Connect to a cellular network (for selected models)
If your computer has a wireless wide area network (WAN) card and a nano-SIM card installed, you can
connect to a cellular data network and get online using the cellular signal.
Note: The cellular service is provided by authorized mobile service carriers in some countries or regions.
You must have a cellular plan from a service carrier to connect to the cellular network.
To establish a cellular connection:
1. Turn off the computer.
2. Insert a straightened paper clip into the hole in the tray 1. The tray ejects. Install a nano-SIM card into
the tray with the metal contacts facing downward 2. Insert the tray into the nano-SIM-card and
microSD-card slot until you hear a click 3. If your computer has a nano-SIM card installed, skip this
step.
© Copyright Lenovo 2020, 2021 13
3. Turn on the computer.
4. Click the network icon in the Windows notification area, and then select the cellular network icon from
the list.
5. Provide required information, if needed.
Use the Vantage app
The preinstalled Vantage app is a customized one-stop solution to help you maintain your computer with
automated updates and fixes, configure hardware settings, and get personalized support.
To access the Vantage app, type Vantage in the Windows search box.
Key features
The Vantage app enables you to:
• Know the device status easily and customize device settings.
• Download and install UEFI BIOS, firmware, and driver updates to keep your computer up-to-date.
• Monitor your computer health, and secure your computer against outside threats.
• Scan your computer hardware and diagnose hardware problems.
• Look up warranty status (online).
• Access User Guide and helpful articles.
Notes:
• The available features vary depending on the computer model.
• The Vantage app makes periodic updates of the features to keep improving your experience with your
computer. The description of features might be different from that on your actual user interface.
Use Lenovo Quick Clean
Depending on the model, your computer might support the Lenovo Quick Clean feature. The preinstalled
Lenovo Quick Clean enables you to temporarily disable the keyboard, screen, trackpad, and TrackPoint
pointing device for cleaning.
Access Lenovo Quick Clean
To access Lenovo Quick Clean, do one of the following:
• Type Lenovo Quick Clean in the Windows search box.
14 T14s Gen 1 and X13 Gen 1 User Guide
Use the keyboard shortcuts
The special keys on the keyboard help you work more easily and effectively.
ThinkPad T14s Gen 1
ThinkPad X13 Gen 1
1. Windows logo key
Open the Start menu.
For information about using this key with other keys, see the Windows help
information.
2. Caps Lock key
Switch the letter case between the upper case and lower case.
When the key indicator is on, you can type uppercase letters.
3. F1–F12 function keys
Invoke the special function printed as an icon on each key or standard function.
To choose whether to invoke the special function or standard function:
1. Go to Control Panel and view by Large icons or Small icons.
2. Click Keyboard or Lenovo - Keyboard Manager and select the option of
your preference.
16 T14s Gen 1 and X13 Gen 1 User Guide
Switch the function of the F1–F12 keys between the standard function and special
function printed as an icon on each key.
When the Fn Lock indicator is on:
• Press F1-F12 to use the standard function.
• Press Fn+F1-F12 to use the special function.
When the Fn Lock indicator is off:
• Press Fn+F1-F12 to use the standard function.
• Press F1-F12 to use the special function.
Mute or unmute the speakers.
When the key indicator is on, the speakers are muted.
If you mute the speakers and turn off your computer, the speakers remain muted
when you turn on your computer.
Volume down.
Volume up.
Mute or unmute the microphones.
When the key indicator is on, the microphones are muted.
Brightness down.
Brightness up.
Manage external displays.
Wireless on / off.
Open or collapse the notification center.
Answer incoming calls on Microsoft Teams.
Decline incoming calls on Microsoft Teams.
Invoke the function defined by yourself.
You can define different functions for the F12 key on the Vantage app.
Open the Snipping Tool program.
Fn+Spacebar Switch between different keyboard backlight statuses if your computer supports
keyboard backlight.
Fn+B Equal the Break key on a conventional external keyboard.
Fn+K Equal the ScrLK or Scroll Lock key on a conventional external keyboard.
Fn+P Equal the Pause key on a conventional external keyboard.
Fn+S Equal the SysRq key on a conventional external keyboard.
Chapter 2.Get started with your computer 17
Fn+4 Put the computer to sleep mode. To wake up the computer, press Fn or the power
button.
Fn+D
If your computer supports the PrivacyGuard feature, press Fn+D to enable or
disable this feature. For more information, see “Use privacy protection (for
selected models)” on page 23.
Fn+Left arrow key Equal the Home key.
Fn+Right arrow key Equal the End key.
Use the TrackPoint pointing device
The TrackPoint pointing device enables you to perform all the functions of a traditional mouse, such as
pointing, clicking, and scrolling.
Use the TrackPoint pointing device
1. Pointing stick
Use your index finger or middle finger to apply pressure to the pointing-stick nonslip cap in any direction
parallel to the keyboard. The pointer on the screen moves accordingly but the pointing stick itself does not
move. The higher the pressure applied, the faster the pointer moves.
2. Left-click button
Press to select or open an item.
3. Right-click button
Press to display a shortcut menu.
4. Middle button
Press and hold the dotted middle button while applying pressure to the pointing stick in the vertical or
horizontal direction. Then, you can scroll through the document, Web site, or apps.
18 T14s Gen 1 and X13 Gen 1 User Guide
Disable the TrackPoint pointing device
The TrackPoint pointing device is active by default. To disable the device:
1. Open the Start menu, and then click Settings ➙ Devices ➙ Mouse.
2. Follow the on-screen instructions to disable TrackPoint.
Replace the pointing-stick nonslip cap
Note: Ensure that the new cap has grooves a.
Use the trackpad
The entire trackpad surface is sensitive to finger touch and movement. You can use the trackpad to perform
all the pointing, clicking, and scrolling functions of a traditional mouse.
Use the trackpad
1. Left-click zone
Press to select or open an item.
You also can tap anywhere on the surface of the trackpad with one finger to perform the left-click action.
2. Right-click zone
Press to display a shortcut menu.
Chapter 2.Get started with your computer 19
You also can tap anywhere on the surface of the trackpad with two fingers to perform the right-click action.
Use the touch gestures
Tap
Tap anywhere on the trackpad with one finger to select or open an
item.
Two-finger tap
Tap anywhere on the trackpad with two fingers to display a shortcut
menu.
Two-finger scroll
Put two fingers on the trackpad and move them in the vertical or
horizontal direction. This action enables you to scroll through the
document, Web site, or apps.
Two-finger zoom out
Put two fingers on the trackpad and move them closer together to
zoom out.
Two-finger zoom in
Put two fingers on the trackpad and move them farther apart to zoom
in.
20 T14s Gen 1 and X13 Gen 1 User Guide
Swipe three fingers up
Put three fingers on the trackpad and move them up to open the task
view to see all your open windows.
Swipe three fingers down
Put three fingers on the trackpad and move them down to show the
desktop.
Notes:
• When using two or more fingers, ensure that you position your fingers slightly apart.
• Some gestures are not available if the last action was done from the TrackPoint pointing device.
• Some gestures are only available when you are using certain apps.
• If the trackpad surface is stained with oil, turn off the computer first. Then, gently wipe the trackpad
surface with a soft and lint-free cloth moistened with lukewarm water or computer cleaner.
For more gestures, see the help information of the pointing device.
Disable the trackpad
The trackpad is active by default. To disable the device:
1. Open the Start menu, and then click Settings ➙ Devices ➙ Touchpad.
2. In the Touchpad section, turn off the Touchpad control.
Use the multi-touch screen (for selected models)
If your computer display supports the multi-touch function, you can navigate the screen with simple touch
gestures.
Note: Some gestures might not be available depending on the app you use.
Tap once
• From the Start menu: Open an app or item.
• From the desktop: Select an app or item.
• In an open app: Perform an action such as Copy, Save, and
Delete, depending on the app.
Tap twice quickly
Open an app or item from the desktop.
Chapter 2.Get started with your computer 21
Tap and hold
Open a shortcut menu.
Slide
Scroll through items, such as lists, pages, and photos.
Drag an item to the location you want
Move an object.
Move two fingers closer together
Zoom out.
Move two fingers farther apart
Zoom in.
Swipe in from the right edge
Open the action center to see your notifications and quick actions.
22 T14s Gen 1 and X13 Gen 1 User Guide
Swipe in from the left edge
View all your open windows in task view.
• Swipe downwards shortly from the top edge (for full-screened
app or when your computer is in the tablet mode)
Show a hidden title bar.
• Swipe in from the top edge to the bottom edge (when your
computer is in the tablet mode)
Close the current app.
Tips
• Turn off the computer before cleaning the multi-touch screen.
• Use a dry, soft, and lint-free cloth or a piece of absorbent cotton to remove fingerprints or dust from the
multi-touch screen. Do not apply solvents to the cloth.
• The multi-touch screen is a glass panel covered with a plastic film. Do not apply pressure or place any
metallic object on the screen, which might damage the touch panel or cause it to malfunction.
• Do not use fingernails, gloved fingers, or inanimate objects for input on the screen.
• Regularly calibrate the accuracy of the finger input to avoid a discrepancy.
Use privacy protection (for selected models)
Use the PrivacyGuard feature
Depending on model, your computer might support the PrivacyGuard feature. When the feature is enabled, it
darkens screen and reduces visibility from side angles to protect screen content against visual hacking. By
default, the PrivacyGuard feature is disabled. You can press F12 or Fn+D to enable it. You will be prompted
by the on-screen icon or every time the feature is enabled or disabled.
The privacy level of this feature varies depending on the screen brightness level, the contrast ratio, and the
physical environment where you are using this feature.
• Press to increase the privacy level.
• Press to decrease the privacy level.
Automatic PrivacyGuard feature for passwords
Though the PrivacyGuard feature is disabled, PrivacyGuard feature could also be automatically enabled in
case that you are required to input passwords. By default, this automatic PrivacyGuard feature for
passwords is disabled. You can enable it on the Vantage app.
Note: The automatic PrivacyGuard feature for passwords is not supported on computers with the Linux®
operating system.
Chapter 2.Get started with your computer 23
Use the PrivacyGuard with PrivacyAlert feature
Glance by Mirametrix® is preinstalled on your computer. Turn on PrivacyAlert and PrivacyGuard switches
on Glance to achieve better privacy protection.
When someone is detected looking over your shoulder by the camera (with IR function), an alert icon appears
on your computer screen. Meanwhile, PrivacyAlert automatically enables PrivacyGuard to prevent peeking
eyes. When the person leaves, the icon disappears and the PrivacyGuard feature is disabled automatically.
Use the Intelligent Cooling feature (for selected models)
The Intelligent Cooling feature enables your computer to work in the following three modes:
• Quiet mode : the quietest fan noise
• Balanced mode : balanced performance and fan noise
• Performance mode : the highest performance and normal fan noise
on ac power on battery power
For computers with Windows operating system, do the following to select the preferred mode:
1. Click the battery status icon in the Windows notification area.
2. Move the slider to the left or right to select your preferred mode.
Use multimedia
Use your computer for business or entertainment with the built-in components (camera, speakers, and audio
features) or connected external devices (an external projector, monitor, and HDTV).
Use audio
To enhance your audio experience, connect speakers, headphones, or a headset with a 3.5-mm (0.14-inch),
4-pole plug to the audio connector.
Change the sound settings
1. Go to Control Panel and view by category.
2. Click Hardware and Sound ➙ Sound.
3. Change the settings as you prefer.
24 T14s Gen 1 and X13 Gen 1 User Guide
Connect to an external display
Connect your computer to a projector or a monitor to give presentations or expand your workspace.
Connect to a wired display
1. Connect the external display to an appropriate video connector on your computer.
2. Connect the external display to an electrical outlet.
3. Turn on the external display.
If your computer cannot detect the external display, right-click a blank area on the desktop and select
display settings. Then follow the on-screen instructions to detect the external display.
For Intel models, do not connect external displays to the USB-C connector 1 and the HDMI connector 2 at
same time. Otherwise, only the external display connected to the USB-C connector 1 will work by default.
You can change the priority between the USB-C connector and the HDMI connector from the UEFI BIOS
menu. To enter the UEFI BIOS menu, see “Enter the UEFI BIOS menu” on page 45, and then select Display
➙ Shared Display Priority. Then, follow the instructions on the screen.
Supported resolution
The following table lists the supported maximum resolution of the external display.
Table 1. Intel models
Connect the external display to Supported resolution
the USB-C (3.2 Gen 1) connector Up to 4096 x 2304 pixels / 60 Hz
the Thunderbolt 3 connector (USB-C) Up to 4096 x 2304 pixels / 60 Hz
the HDMI connector Up to 4096 x 2160 pixels / 24 Hz
Table 2. AMD models
Connect the external display to Supported resolution
the USB-C (3.2 Gen 2) connector Up to 5120 x 2880 pixels / 60 Hz
the HDMI connector Up to 4096 x 2160 pixels / 60 Hz
Connect to a wireless display
To use a wireless display, ensure that both your computer and the external display support the Miracast®
feature.
Press + and then select a wireless display to connect with.
Chapter 2.Get started with your computer 25
Set the display mode
Press or and then select a display mode of your preference.
Press or and then select a display mode of your preference.
Change display settings
1. Right-click a blank area on the desktop and select display settings.
2. Select the display that you want to configure and change display settings of your preference.
You can change the settings for both the computer display and the external display. For example, you can
define which one is the main display and which one is the secondary display. You also can change the
resolution and orientation.
26 T14s Gen 1 and X13 Gen 1 User Guide
Chapter 3. Explore your computer
Manage power
Use the information in this section to achieve the best balance between performance and power efficiency.
Check the battery status
Click the battery icon in the Windows notification area to check the battery status, view the current power
plan, change the power mode, and access battery settings quickly. For more details about your battery, refer
to the Vantage app.
Charge the computer
Use ac power
When the battery power is low, charge your battery by connecting your computer to ac power.
The battery is fully charged in about four to eight hours. If the power adapter shipped with your computer
supports the rapid charge function, the battery is 80% charged in about one hour when the computer is
turned off. The actual charging time depends on the battery size, the physical environment, and whether you
are using the computer.
Battery charging is also affected by the battery temperature. The recommended battery temperature range
for charging the battery is between 10°C (50°F) and 35°C (95°F).
Notes:
• To maximize the life of the battery, once the battery is fully charged, it must discharge to below 95%
before it will be allowed to recharge again.
• To extend your battery’s lifespan, we may optimize its full charge capacity based on your usage. After
prolonged periods of limited use, full battery capacity may not be available until you discharge to as low
as 20% and recharge completely. For more information, refer to the power section of the Vantage app.
Use P-to-P 2.0 charging function
• For Intel models, both the USB-C (3.2 Gen 1) connector and Thunderbolt 3 connector (USB-C) feature the
Lenovo-unique P-to-P 2.0 charging function.
• For AMD models, both the USB-C (3.2 Gen 2) connectors feature the Lenovo-unique P-to-P 2.0 charging
function.
© Copyright Lenovo 2020, 2021 27
When no ac power is available, this feature enables one computer to supply power to another computer
through a USB-C to USB-C cable. When ac power is available for only one computer, this feature enables
both computers to get charged by ac power.
Before using the function, ensure that:
• The selected connectors support the P-to-P 2.0 charging function and power delivery function.
• Always On USB and Charge in Battery Mode are enabled in UEFI BIOS of both computers, so that the
function works even when the computers are off or in hibernation mode. To enable Always On USB and
Charge in Battery Mode:
1. Enter the UEFI BIOS menu. See “Enter the UEFI BIOS menu” on page 45.
2. Click Config ➙ USB to enable Always On USB and Charge in Battery Mode.
To use the function:
• When no ac power is available:
The remaining battery power of computer A should be at least 30% and be 3% higher than that of
computer B. To check the battery status, see “Check the battery status” on page 27. Connect the
computers to each other with a USB-C to USB-C cable. In this situation, computer A works as the power
supply. Once the remaining battery power of computer A is lower than 30%, computer A stops supplying
power to computer B.
• When ac power is available:
Connect the computers to each other with a USB-C to USB-C cable. Connect one computer to ac power.
In this situation, ac power works as the power supply and both computers get charged.
Note: The actual charging speed using the Lenovo-unique P-to-P 2.0 charging function varies depending on
many factors, such as the remaining battery power of the computers, the wattage of the ac power adapter,
and whether you are using the computers.
Maximize the battery life
• Lower the brightness of the computer display.
• Turn off the wireless features when not in use.
• Use the battery until the charge is depleted.
• Recharge the battery completely before using it.
28 T14s Gen 1 and X13 Gen 1 User Guide
Set power button behaviors
You can define what the power button does according to your preference. For example, by pressing the
power button, you can turn off the computer or put the computer to sleep or hibernation mode.
To change what the power button does:
1. Right-click the battery status icon and select Power Options ➙ Change what the power buttons do.
2. Change the settings as you prefer.
Set the power plan
For ENERGY STAR® compliant computers, the following power plan takes effect when your computers have
been idle for a specified duration:
Table 3. Default power plan (when plugged into ac power)
• Turn off the display: After 10 minutes
• Put the computer to sleep: After 10 minutes
To reset the power plan to achieve the best balance between performance and power saving:
1. Right-click the battery status icon and select Power Options.
2. Choose or customize a power plan of your preference.
Transfer data
Quickly share your files using the built-in Bluetooth or NFC technology among devices with the same
features. You also can insert a microSD card or smart card to transfer data.
Set up a Bluetooth connection
You can connect all types of Bluetooth-enabled devices to your computer, such as a keyboard, a mouse, a
smartphone, or speakers. To ensure successful connection, place the devices at most 10 meters (33 feet)
from the computer.
1. Type Bluetooth in the Windows search box and then press Enter.
2. Turn on Bluetooth, if it is off.
3. Select a Bluetooth device, and then follow the on-screen instructions.
Set up an NFC connection (for selected Intel models)
If your computer supports NFC, you will see an NFC mark or label around the trackpad area.
NFC is a high-frequency and short-range wireless communication technology. By using NFC, you can simply
tap and connect your computer and another NFC-enabled device over a few centimeters or inches.
Turn on NFC
1. Type Airplane mode in the Windows search box and then press Enter.
2. Ensure that the Airplane mode is off and turn on the NFC function.
Chapter 3.Explore your computer 29
Pair with an NFC card or NFC-enabled smartphone
Before you start, ensure that:
• The card is in NFC Data Exchange Format (NDEF), otherwise the card cannot be detected.
• The smartphone screen is facing upward.
To pair with an NFC card or smartphone:
1. Place the card or smartphone closely near the NFC mark or label area on your computer.
2. Slowly move the card or smartphone around the NFC mark or label until you are prompted that the
device has been successfully detected.
Attention: During the data transfer, do not put your computer to sleep mode or lock the smartphone;
otherwise, your data might get damaged.
Use a microSD card (for selected models)
If your computer has a nano-SIM-card and microSD-card slot, read the following information.
Supported microSD card
• Secure Digital (SD) card
• Secure Digital eXtended-Capacity (SDXC) UHS-1 card
• Secure Digital High-Capacity (SDHC) UHS-1 card
Attention:
• Before handling the microSD card, touch a metal table or a grounded metal object. Otherwise the card
might get damaged by the static electricity from your body.
• During the data transfer, do not put your computer into sleep mode; otherwise, your data could get
damaged.
Replace or install a microSD card:
Note: Depending on the model, your tray might not support nano-SIM card, and it might look slightly
different from the illustrations in this topic.
1. Insert a straightened paper clip into the hole in the tray. The tray ejects. Then, slide the tray out of the
computer. If a microSD card is installed, gently take the microSD card out of the tray.
2. Ensure that the new microSD card is installed in correct orientation. Install a new microSD card into the
tray with the metal contacts facing downward. Insert the tray into the nano-SIM-card and microSD-card
slot until you hear a click.
30 T14s Gen 1 and X13 Gen 1 User Guide
Use a smart card (for selected models)
If your computer has a smart-card slot, read the following information.
Supported smart card
Supported smart card specifications: 85.60 mm (3.37 inches) x 53.98 mm (2.13 inches)
Attention: Smart cards with slits are not supported. Do not insert such a smart card into the smart-card
reader of your computer. Otherwise, the reader might get damaged.
Install the card
1. Locate the card slot.
2. Insert the card firmly into the card slot until it is secured in place. Ensure that the metal contacts are
facing upward and pointing toward the card slot.
Remove the card
Attention: Before removing a card, eject the card from the Windows operating system first. Otherwise, data
on the card might get corrupted or lost.
1. Click the triangular icon in the Windows notification area to show hidden icons. Right-click the icon
prompting you to safely remove hardware and eject media.
2. Select the corresponding item to eject the card from the Windows operating system.
3. Press the card and remove it from your computer. Store the card safely for future use.
Turn on the Airplane mode
When the Airplane mode is enabled, all wireless features are disabled.
1. Click the action center icon in the Windows notification area.
2. Click Airplane mode to turn on the Airplane mode.
Chapter 3.Explore your computer 31
Use the factory color calibration feature (for selected models)
The factory color calibration feature is available on computer models shipped with a pre-calibrated display.
The feature enables you to render color images or graphics on your display close to the original intent as
much as possible.
For computer models with the factory color calibration feature, the color profiles are preinstalled. You can
switch between color profiles as desired:
1. Click the triangular icon in the Windows notification area to show hidden icons. Then, right-click .
2. Follow the on-screen instructions to select a profile as desired.
Lenovo provides backup color profiles in Lenovo Cloud. You might need to restore or install color profiles in
the following situations:
• If any color profile is lost or damaged, a window will be displayed to remind you to restore the color
profiles. Click Yes in the window prompted, and the color profiles will be restored from Lenovo Cloud
automatically.
• If your display has been replaced by a Lenovo-authorized service provider, do the following to install new
color profiles:
1. Connect your computer to the network and close the X-Rite Color Assistant program.
2. Go to C:\Program files (x86)\X-Rite Color Assistant and locate the
ProfileUpdaterForDisplayReplacement.exe file.
3. Double-click the EXE file. Then, follow the on-screen instructions to input the display serial number
and click Submit.
Note: When the new color profiles are installed successfully, a window will be displayed.
32 T14s Gen 1 and X13 Gen 1 User Guide
Chapter 4. Accessories
This chapter provides instructions on how to use hardware accessories to expand your computer
capabilities.
Purchase options
Lenovo has a number of hardware accessories and upgrades to help expand the capabilities of your
computer. Options include memory modules, storage devices, network cards, port replicators or docking
stations, batteries, power adapters, keyboards, mice, and more.
To shop at Lenovo, go to https://www.lenovo.com/accessories.
Docking station
You can use the following docking stations to extend the capacity of your computer:
• ThinkPad Basic Docking Station
• ThinkPad Pro Docking Station
• ThinkPad Ultra Docking Station
© Copyright Lenovo 2020, 2021 33
Front view
Note: The following illustration is based on ThinkPad Basic Docking Station. The ThinkPad Pro Docking
Station and ThinkPad Ultra Docking Station might look slightly different.
1. System lock
Use the system lock in the following ways:
• Locked position : The latch is locked, and you cannot attach or detach your
computer.
• Unlocked position : The latch is unlocked, and you can attach or detach
your computer.
• Removal position : You can remove the system lock from the system-lock
slot.
Note: The ThinkPad Basic Docking Station does not ship with a system lock
installed. You can contact Lenovo sales to purchase a system lock with the option
part number 4XE0Q56388.
2. Key lock indicator This indicator turns on when the system lock key is in the locked position.
3. Docking status indicator This indicator turns on when your computer is successfully connected to the
docking station.
4. Power button Press the power button to turn on or turn off the computer attached to the
docking station.
5. Guide post Use the guide post to help you position your computer properly when you attach
the computer to the docking station.
6. Docking-station connector Connect the computer to the docking station.
7. Hooks Hold and secure the computer to the docking station.
8. Latch Slide the latch to attach or detach the computer.
34 T14s Gen 1 and X13 Gen 1 User Guide
Rear view
Figure 1. ThinkPad Basic Docking Station
Figure 2. ThinkPad Pro Docking Station
Figure 3. ThinkPad Ultra Docking Station
Connectors ThinkPad Basic Docking
Station
ThinkPad Pro Docking
Station
ThinkPad Ultra Docking
Station
1. Audio connector √ √ √
2. ac power connector √ √ √
3. DisplayPort® connector √ √ √
4. VGA connector √ √
5. USB 2.0 connector √ √
6. Always On USB 3.2
connector Gen 1
√ √
7. USB 3.2 connector Gen
1
√ √
8. Ethernet connector √ √ √
9. Security-lock slot √ √ √
10. USB-C connector √ √
11. HDMI connector √
12. Always On USB 3.2
connector Gen 2
√
13. USB 3.2 connector Gen
2
√
Chapter 4.Accessories 35
Note: The security-lock slot supports cable locks that conform to the Kensington MicroSaver lock standards
(using T-bar locking technology) or MiniSaver lock standards (using Cleat locking technology).
Attach a docking station
Notes:
• The ThinkPad Basic Docking Station does not ship with a system lock installed. If you do not purchase
and install a system lock, skip step 4 and step 7 in the following instruction.
• If you do not connect the docking station to ac power, the computer attached runs on battery power.
1. Connect the docking station to ac power.
2. Disconnect the cables and devices from the left side of the computer.
3. Turn the system lock key to the unlocked position ( ).
4. Align the top-left corner of the computer with the guide post of the docking station. Attach your
computer to the docking station as shown 1 until you hear a click. Slide the latch in the direction as
shown 2.
36 T14s Gen 1 and X13 Gen 1 User Guide
5. Check the docking status indicator. The docking status indicator turns on when the computer is
successfully docked.
Note: If the indicator is off, your computer is not attached to the docking station successfully. To solve
the problem, detach and reattach the computer.
6. Turn the system lock key to the locked position ( ).
Attention: When the computer is attached to a docking station, always hold the whole assembly when you
need to move your computer. Otherwise, the docking station might drop down.
Detach a docking station
Note: The ThinkPad Basic Docking Station does not ship with a system lock installed. If you do not
purchase and install a system lock, skip step 1 in the following instruction.
1. Turn the system lock key to the unlocked position ( ).
Chapter 4.Accessories 37
2. Slide the latch in the direction as shown 1 to release the computer, and then grasp both sides of the
computer to remove it 2.
Connect multiple external displays
You can connect multiple external displays to a supported docking station. To ensure that the multiple
displays work correctly, observe the following guidelines and connect the external displays to the
appropriate connectors.
Docking station Supported external displays Video connectors
ThinkPad Basic Docking Station Up to two DisplayPort
VGA
ThinkPad Pro Docking Station Up to two DisplayPort (x2)
ThinkPad Ultra Docking Station Up to three
DisplayPort (x2)
HDMI
VGA
38 T14s Gen 1 and X13 Gen 1 User Guide
Chapter 5. Secure your computer and information
Lock the computer
Lock your computer to a desk, table, or other fixtures through a compatible security cable lock.
Note: The slot supports cable locks that conform to the Kensington MicroSaver® lock standards (using T-
bar™ locking technology) or MiniSaver® lock standards (using Cleat™ locking technology). You are
responsible for evaluating, selecting, and implementing the locking device and security feature. Lenovo
makes no comments, judgments, or warranties about the function, quality, or performance of the locking
device and security feature. Cable locks for your product are available from Lenovo at https://
smartfind.lenovo.com/.
Use passwords
This section introduces types of passwords in UEFI (Unified Extensible Firmware Interface) BIOS (Basic
Input/Output System) and how to set, change, and remove a password.
Password types
You can set a power-on password, supervisor password, system management password, or hard disk
password in UEFI BIOS to prevent unauthorized access to your computer. However, you are not prompted to
enter any UEFI BIOS password when your computer resumes from sleep mode.
Power-on password
If you set a power-on password, a window is displayed on the screen when you turn on the computer. Enter
the correct password to use the computer.
© Copyright Lenovo 2020, 2021 39
Supervisor password
The supervisor password protects the system information stored in UEFI BIOS. When entering the UEFI
BIOS menu, enter the correct supervisor password in the window prompted. You also can press Enter to
skip the password prompt. However, you cannot change most of the system configuration options in UEFI
BIOS.
If you have set both the supervisor password and power-on password, you can use the supervisor password
to access your computer when you turn it on. The supervisor password overrides the power-on password.
System management password
The system management password can also protect the system information stored in UEFI BIOS like a
supervisor password, but it has lower authority by default. The system management password can be set
through the UEFI BIOS menu or through Windows Management Instrumentation (WMI) with the Lenovo
client-management interface.
You can enable the system management password to have the same authority as the supervisor password
to control security related features. To customize the authority of the system management password through
the UEFI BIOS menu:
1. Enter the UEFI BIOS menu. See “Enter the UEFI BIOS menu” on page 45.
Note: When prompted to enter the password, enter the correct supervisor password if a supervisor
password has been set, or enter the correct system management password if no supervisor password
has been set. Otherwise, you cannot change the configurations in the following steps.
2. Select Security ➙ Password ➙ System Management Password Access Control.
3. Follow the on-screen instructions.
If you have set both the supervisor password and the system management password, the supervisor
password overrides the system management password. If you have set both the system management
password and the power-on password, the system management password overrides the power-on
password.
Hard disk passwords
The hard disk password prevents unauthorized access to the data on the storage drive. When a hard disk
password is set, you are prompted to type a correct password each time you try to access the storage drive.
To set the hard disk password, select one of the following types:
• User hard disk password only
When a user hard disk password is set without a master hard disk password, the user must enter the user
hard disk password to access files and applications on the storage drive.
• Master hard disk password + User hard disk password
The master hard disk password is set and used by a system administrator. It enables the administrator to
access any storage drive in a system or any computer connected in the same network. The administrator
can also assign a user hard disk password for each computer in the network. The user of the computer
can change the user hard disk password as desired, but only the administrator can remove the user hard
disk password.
When prompted to enter a hard disk password, press F1 to switch between the master hard disk password
and user hard disk password.
Note: The hard disk password is not available in the following situations:
40 T14s Gen 1 and X13 Gen 1 User Guide
• A Trusted Computing Group (TCG) Opal-compliant storage drive and a TCG Opal management software
program are installed in the computer, and the TCG Opal management software program is activated.
• An eDrive storage drive is installed in the computer preinstalled with the Windows operating system.
Set, change, and remove a password
Before you start, print these instructions.
1. Restart the computer. When the logo screen is displayed, press F1 to enter the UEFI BIOS menu.
2. Select Security ➙ Password by using the arrow keys.
3. Select the password type. Then, follow the on-screen instructions to set, change, or remove a
password.
You should record all your passwords and store them in a safe place. If you forget any of your passwords,
any potential repair actions required are not covered under warranty.
What to do if you forget your power-on password
If you forget your power-on password, do the following to remove the power-on password:
• If you have set a supervisor password and remember it:
1. Restart the computer. When the logo screen is displayed, immediately press F1.
2. Type the supervisor password to enter the UEFI BIOS menu.
3. Select Security ➙ Password ➙ Power-On Password by using the arrow keys.
4. Type the current supervisor password in the Enter Current Password field. Then, leave the Enter
New Password field blank, and press Enter twice.
5. In the Changes have been saved window, press Enter.
6. Press F10 to save changes and exit the UEFI BIOS menu.
• If you have not set a supervisor password, contact a Lenovo authorized service provider to have the
power-on password removed.
What to do if you forget your hard disk password
If you forget your user hard disk password or both user and master hard disk passwords, Lenovo cannot
reset your passwords or recover data from the storage drive. You can contact a Lenovo authorized service
provider to have the storage drive replaced. A fee will be charged for parts and service. If the storage drive is
a CRU (Customer Replaceable Unit), you can also contact Lenovo to purchase a new storage drive to
replace the old one by yourself. To check whether the storage drive is a CRU and the relevant replacement
procedure, see Chapter 7 “CRU replacement” on page 49.
What to do if you forget your supervisor password
If you forget your supervisor password, there is no service procedure to remove the password. You have to
contact a Lenovo authorized service provider to have the system board replaced. A fee will be charged for
parts and service.
What to do if you forget your system management password
If you forget your system management password, do the following to remove the system management
password:
• If you have set a supervisor password and remember it:
1. Restart the computer. When the logo screen is displayed, immediately press F1.
2. Type the supervisor password to enter the UEFI BIOS menu.
3. Select Security ➙ Password ➙ System Management Password by using the arrow keys.
Chapter 5.Secure your computer and information 41
4. Type the current supervisor password in the Enter Current Password field. Then, leave the Enter
New Password field blank, and press Enter twice.
5. In the Changes have been saved window, press Enter.
6. Press F10 to save changes and exit the UEFI BIOS menu.
• If you have not set a supervisor password, contact a Lenovo authorized service provider to have the
system management password removed.
Use Power Loss Protection function (for selected models)
For models shipped with an NVMe (Non-Volatile Memory express) M.2 solid-state drive, the M.2 solid-state
drive features the Lenovo-unique PLP (Power Loss Protection) function to avoid data loss or damage. On
very rare occasions, your computer is not responding and you might have to shut down your computer by
pressing and holding the power button for about seven seconds. In this case, the PLP function enables key
data of your computer to be saved timely. However, there is no guarantee that all data is saved in any
situation. To check the type of your M.2 solid-state drive:
1. Restart the computer. When the logo screen is displayed, press F10 to enter the Lenovo diagnostics
window.
2. On the TOOLS tab, select SYSTEM INFORMATION ➙ STORAGE using the arrow keys.
3. Locate the Device Type section to check the information.
Use the fingerprint reader (for selected models)
If your computer comes with a fingerprint reader, you can use it to enroll your fingerprints. After enrollment,
you can tap your finger on the fingerprint reader to log in to Windows.
Enroll your fingerprints
1. Type Sign-in options in the Windows search box and then press Enter.
2. Select the fingerprint setting and then follow the on-screen instruction to enroll your fingerprint.
Note: It is recommended that you put your finger at the middle of the fingerprint reader during
enrollment and enroll more than one fingerprint in case of any injuries to your fingers. After the
enrollment, the fingerprints are associated with the Windows password automatically.
Log in with your fingerprint
Associate your fingerprints with your power-on password and hard disk password
1. Turn off and then turn on the computer.
2. When prompted, scan your finger on the fingerprint reader.
3. Enter your power-on password, hard disk password, or both as required. The connection is created.
When you start the computer again, you can use your fingerprints to log in to the computer without entering
your Windows password, power-on password, or hard disk password. To change the settings, go to the
UEFI BIOS menu.
42 T14s Gen 1 and X13 Gen 1 User Guide
Attention: If you always use your fingerprint to log in to the computer, you might forget your passwords.
Write down your passwords, and keep them in a safe place.
Maintain the fingerprint reader
To ensure that the fingerprint reader works correctly, do not:
• Scratch the surface of the reader with anything hard.
• Use or touch the reader with a wet, dirty, wrinkled, or injured finger.
Use face authentication (for selected models)
If your computer comes with a Windows Hello-compatible infrared camera, you can unlock your computer by
scanning your face instead of using a password.
Note: If your computer is equipped with a ThinkShutter, slide the ThinkShutter to uncover the camera lens
before using the Windows Hello face recognition.
Create your face ID and unlock your computer by scanning your face:
1. Type Sign-in options in the Windows search box and then press Enter.
2. Select the face ID setting and then follow the on-screen instruction to create your face ID.
Use firewalls and antivirus programs
Your computer might be preinstalled with a firewall program. The firewall protects against computer Internet
security threats, unauthorized access, intrusions, and Internet attacks. It also protects your privacy.
A full version of antivirus program is provided with a free 30-day subscription. After 30 days, you must renew
the license to continue receiving the antivirus program updates.
For more information, see the help system of the program.
Chapter 5.Secure your computer and information 43
44 T14s Gen 1 and X13 Gen 1 User Guide
Chapter 6. Configure advanced settings
This chapter provides information about UEFI BIOS, RAID, recovery, operating system installation, and
system management.
UEFI BIOS
This section introduces what is UEFI BIOS and the operations you can perform in UEFI BIOS.
What is UEFI BIOS
UEFI BIOS is the first program that the computer runs when the computer is turned on. UEFI BIOS initializes
the hardware components and loads the operating system and other programs. Your computer comes with a
setup program with which you can change UEFI BIOS settings.
Enter the UEFI BIOS menu
Restart the computer. When the logo screen is displayed, press F1 to enter the UEFI BIOS menu.
Note: If you have set the supervisor password, enter the correct password when prompted. You also can
press Enter to skip the password prompt and enter the UEFI BIOS menu. However, you cannot change the
system configurations that are protected by the supervisor password.
Navigate in the UEFI BIOS interface
Attention: The default configurations are already optimized for you in boldface. Improper change of the
configurations might cause unexpected results.
You can navigate in the UEFI BIOS interface by pressing the following keys:
F1 Display the General Help screen.
F9 Restore to the default settings.
F10 Save your configuration and exit.
F5 Change to a lower value.
F6 Change to a higher value.
↑↓ Locate an item.
Tab Select a tab.
Esc Exit the submenu and return to the parent menu.
Enter Enter the selected tab or submenu.
Change the startup sequence
1. Restart the computer. When the logo screen is displayed, press F1.
2. Select Startup ➙ Boot. Then, press Enter. The default device order list is displayed.
Note: No bootable device is displayed if the computer cannot start from any devices or the operating
system cannot be found.
3. Set the startup sequence as desired.
© Copyright Lenovo 2020, 2021 45
4. Press F10 to save the changes and exit.
To change the startup sequence temporarily:
1. Restart the computer. When the logo screen is displayed, press F12.
2. Select the device that you want the computer to start from and press Enter.
Set the system date and time
1. Restart the computer. When the logo screen is displayed, press F1.
2. Select Date/Time and set the system date and time as desired.
3. Press F10 to save changes and exit.
Update UEFI BIOS
When you install a new program, device driver, or hardware component, you might need to update UEFI
BIOS.
Download and install the latest UEFI BIOS update package by one of the following methods:
• Open the Vantage app to check the available update packages. If the latest UEFI BIOS update package is
available, follow the on-screen instructions to download and install the package.
• Go to https://pcsupport.lenovo.com and select the entry for your computer. Then, follow the on-screen
instructions to download and install the latest UEFI BIOS update package.
Install a Windows operating system and drivers
This section provides instructions on installing a Windows operating system and device drivers.
Install a Windows operating system
Microsoft constantly makes updates to the Windows operating system. Before installing a particular
Windows version, check the compatibility list for the Windows version. For details, go to https://
support.lenovo.com/us/en/solutions/windows-support.
Attention:
• It is recommended that you update your operating system through official channels. Any unofficial update
might cause security risks.
• The process of installing a new operating system deletes all the data on your internal storage drive,
including the data stored in a hidden folder.
• For computer models that are installed with a hybrid solid-state drive (with Intel Optane memory), ensure
that you do not install the operating system into Optane memory.
1. If you are using the Windows BitLocker® Drive Encryption feature and your computer has a Trusted
Platform Module, ensure that you have disabled the feature.
2. Ensure that the security chip is set to Active.
a. Restart the computer. When the logo screen is displayed, press F1 to enter the UEFI BIOS menu.
b. Select Security ➙ Security Chip and press Enter. The Security Chip submenu opens.
c. Ensure that the security chip for TPM 2.0 is set to Active.
d. Press F10 to save the settings and exit.
46 T14s Gen 1 and X13 Gen 1 User Guide
3. For computer models that are installed with hybrid solid-state drive (with Intel Optane memory), enter
the UEFI BIOS menu and select Config ➙ Storage ➙ Controller mode. Ensure that RST mode is
selected.
4. Connect the drive that contains the operating system installation program to the computer.
5. Restart the computer. When the logo screen is displayed, press F1 to enter the UEFI BIOS menu.
6. Select Startup ➙ Boot to display the Boot Priority Order submenu.
7. Select the drive that contains the operating system installation program, for example, USB HDD. Then,
press Esc.
Attention: After you change the startup sequence, ensure that you select the correct device during a
copy, a save, or a format operation. If you select the wrong device, the data on that device might be
erased or overwritten.
8. Select Restart and ensure that OS Optimized Defaults is enabled. Then, press F10 to save the settings
and exit.
9. Follow the on-screen instructions to install the device drivers and necessary programs.
10. After installing the device drivers, apply Windows Update to get the latest updates, for example the
security patches.
Install device drivers
You should download the latest driver for a component when you notice poor performance from that
component or when you added a component. This action might eliminate the driver as the potential cause of
a problem. Download and install the latest driver by one of the following methods:
• Open the Vantage app to check the available update packages. Select the update packages you want,
and then follow the on-screen instructions to download and install the packages.
• Go to https://pcsupport.lenovo.com and select the entry for your computer. Then, follow the on-screen
instructions to download and install necessary drivers and software.
Chapter 6.Configure advanced settings 47
48 T14s Gen 1 and X13 Gen 1 User Guide
Chapter 7. CRU replacement
What are CRUs
Customer Replaceable Units (CRUs) are parts that can be upgraded or replaced by the customer. The
computers contain the following types of CRUs:
• Self-service CRUs: Refer to parts that can be installed or replaced easily by customer themselves or by
trained service technicians at an additional cost.
• Optional-service CRUs: Refer to parts that can be installed or replaced by customers with a greater skill
level. Trained service technicians can also provide service to install or replace the parts under the type of
warranty designated for the customer’s machine.
If you intend on installing a CRU, Lenovo will ship the CRU to you. CRU information and replacement
instructions are shipped with your product and are available from Lenovo at any time upon request. You
might be required to return the defective part that is replaced by the CRU. When return is required: (1) return
instructions, a prepaid shipping label, and a container will be included with the replacement CRU; and (2) you
might be charged for the replacement CRU if Lenovo does not receive the defective CRU within thirty (30)
days of your receipt of the replacement CRU. For full details, see the Lenovo Limited Warranty
documentation at https://www.lenovo.com/warranty/llw_02.
Refer to the following CRU list for your computer.
Self-service CRUs
• ac power adapter
• Base cover assembly
• Nano-SIM-card and microSD-card tray*
• Power cord
Optional-service CRUs
• Keyboard (for ThinkPad X13 Gen 1)
• M.2 solid-state drive*
• M.2 solid-state drive bracket*
• Wireless WAN card*
* for selected models
Note: Replacement of any parts not listed above, including the built-in rechargeable battery, must be done
by a Lenovo-authorized repair facility or technician. Go to https://support.lenovo.com/partnerlocation for more
information.
Disable Fast Startup and the built-in battery
Before replacing any CRU, ensure that you disable Fast Startup first and then disable the built-in battery.
To disable Fast Startup:
1. Go to Control Panel and view by Large icons or Small icons.
2. Click Power Options, and then click Choose what the power buttons do on the left pane.
3. Click Change settings that are currently unavailable at the top.
© Copyright Lenovo 2020, 2021 49
4. If prompted by User Account Control (UAC), click Yes.
5. Clear the Turn on fast startup check box, and then click Save changes.
To disable the built-in battery:
1. Restart your computer. When the logo screen is displayed, immediately press F1 to enter the UEFI BIOS
menu.
2. Select Config ➙ Power. The Power submenu is displayed.
3. Select Disable Built-in Battery and press Enter.
4. Select Yes in the Setup Confirmation window. The built-in battery is disabled and the computer turns off
automatically. Wait three to five minutes to let the computer cool.
Replace a CRU
Follow the replacement procedure to replace a CRU.
Base cover assembly
Prerequisite
Before you start, read Appendix A “Important safety information” on page 71 and print the following
instructions.
Note: There might be a risk of short circuits if you remove the base cover assembly when your computer is
connected to ac power.
Replacement procedure
1. Disable the built-in battery. See “Disable Fast Startup and the built-in battery” on page 49.
2. Turn off the computer and disconnect the computer from ac power and all connected cables.
3. Close the computer display and turn over the computer.
4. Loosen the screws that secure the base cover assembly 1. Push the base cover assembly forward as
shown 2 and remove the base cover assembly 3.
50 T14s Gen 1 and X13 Gen 1 User Guide
5. Install a new base cover assembly in place 1. Press the left and right sides of the base cover assembly
as shown 2 and then tighten the screws in ascending alphabetical order (a to e) as illustrated 3.
6. Turn over the computer. Connect the ac power adapter and all disconnected cables to the computer.
Troubleshooting
If the computer does not start up after you reinstall the base cover assembly, disconnect the ac power
adapter and then reconnect it to the computer.
M.2 solid-state drive
Prerequisite
Before you start, read Appendix A “Important safety information” on page 71 and print the following
instructions.
Attention:
• If you replace a M.2 solid-state drive, you might need to install a new operating system. For details on how
to install a new operating system, see “Install a Windows operating system and drivers” on page 46.
• If your computer is installed with a hybrid solid-state drive (with Intel Optane memory), go to https://
support.lenovo.com/docs/tg_ssd to know the details on how to replace it.
The M.2 solid-state drive is sensitive. Inappropriate handling might cause damage and permanent loss of
data.
When handling the M.2 solid-state drive, observe the following guidelines:
• Replace the M.2 solid-state drive only for upgrade or repair. The M.2 solid-state drive is not designed for
frequent changes or replacement.
• Before replacing the M.2 solid-state drive, make a backup copy of all the data that you want to keep.
• Do not apply pressure to the M.2 solid-state drive.
• Do not touch the contact edge or circuit board of the M.2 solid-state drive. Otherwise, the M.2 solid-state
drive might get damaged.
• Do not make the M.2 solid-state drive subject to physical shocks or vibration. Put the M.2 solid-state drive
on a soft material, such as cloth, to absorb physical shocks.
Chapter 7.CRU replacement 51
The long M.2 solid-state drive
1. Disable the built-in battery. See “Disable Fast Startup and the built-in battery” on page 49.
2. Turn off the computer and disconnect the computer from ac power and all connected cables.
3. Close the computer display and turn over the computer.
4. Remove the base cover assembly. See “Base cover assembly” on page 50.
5. Remove the screw that secures the M.2 solid-state drive 1. Then, remove the drive out of the slot 2.
6. Install a new M.2 solid-state drive:
a. Align the contact edge of the new M.2 solid-state drive with the key in the slot. Then, carefully insert
the drive into the slot at an angle of about 20 degrees 1.
b. Pivot the M.2 solid-state drive downward 2.
c. Install the screw to secure the M.2 solid-state drive 3.
52 T14s Gen 1 and X13 Gen 1 User Guide
7. Reinstall the base cover assembly.
8. Turn over the computer. Connect the ac power adapter and all disconnected cables to the computer.
The short M.2 solid-state drive and its bracket
1. Disable the built-in battery. See “Disable Fast Startup and the built-in battery” on page 49.
2. Turn off the computer and disconnect the computer from ac power and all connected cables.
3. Close the computer display and turn over the computer.
4. Remove the base cover assembly. See “Base cover assembly” on page 50.
5. Do one of the following to remove the M.2 solid-state drive and its bracket:
• Type one: Remove the screws that secure the M.2 solid-state drive bracket 1, and remove the
bracket 2. Then, remove the drive out of the slot 3.
• Type two: Remove the screw that secures the M.2 solid-state drive bracket 1, and remove the
bracket 2. Then, remove the drive out of the slot 3.
Chapter 7.CRU replacement 53
6. Do one of the following to install the M.2 solid-state drive and its bracket:
• Type one: Align the contact edge of the new M.2 solid-state drive with the key in the slot. Then,
carefully insert the drive into the slot 1. Then, Put the bracket in place 2. Install the screws to secure
the bracket 3.
• Type two: Install the new M.2 solid-state drive on the bracket 1 and insert the new M.2 solid-state
drive with the bracket into the drive slot 2. Then, install the screw to secure the bracket 3.
7. Reinstall the base cover assembly.
8. Turn over the computer. Connect the ac power adapter and all disconnected cables to the computer.
Wireless WAN card (for selected models)
The following information is only for the computer with user-installable modules. Ensure that you use only a
Lenovo-authorized wireless module specifically tested for this computer model. Otherwise, the computer will
generate an error-code beep sequence when you turn on the computer.
54 T14s Gen 1 and X13 Gen 1 User Guide
Prerequisite
Before you start, read Appendix A “Important safety information” on page 71 and print the following
instructions.
Attention: Do not touch the contact edge of the wireless WAN card. Otherwise, the wireless WAN card
might get damaged.
Replacement procedure
1. Disable the built-in battery. See “Disable Fast Startup and the built-in battery” on page 49.
2. Turn off the computer and disconnect the computer from ac power and all connected cables.
3. Close the computer display and turn over the computer.
4. Remove the base cover assembly. See “Base cover assembly” on page 50.
5. Remove the wireless WAN card:
Note: A Mylar film might cover the wireless WAN card. To access the wireless WAN card, open the
Mylar film first.
a. Gently disconnect the wireless cable connectors with your fingers 1. Then, remove the screw that
secures the wireless WAN card 2 and the card pivots up.
b. Carefully remove the wireless WAN card out of the slot 3.
Chapter 7.CRU replacement 55
6. Install a new wireless WAN card:
a. Align the contact edge of the new wireless WAN card with the key in the slot. Then, carefully insert
the card into the slot at an angle of about 20 degrees 1 and pivot downward 2.
b. Install the screw to secure the wireless WAN card in place 3. Connect the wireless cable connectors
to the card 4. Ensure that you connect the orange cable to the main connector on the card, and the
blue cable to the auxiliary connector on the card.
7. Reinstall the base cover assembly.
8. Turn over the computer. Connect the ac power adapter and all disconnected cables to the computer.
Keyboard (for ThinkPad X13 Gen 1)
Prerequisite
Before you start, read Appendix A “Important safety information” on page 71 and print the following
instructions.
Replacement procedure
Note: You might be instructed to slide the keyboard frame forward or backward in some of the following
steps. In this case, ensure that you do not press or hold the keys while sliding the keyboard frame.
Otherwise, the keyboard frame cannot be moved.
1. Disable the built-in battery. See “Disable Fast Startup and the built-in battery” on page 49.
2. Turn off the computer and disconnect the computer from ac power and all connected cables.
56 T14s Gen 1 and X13 Gen 1 User Guide
3. Take the tool out of the new keyboard package. Insert the tabs a and b into the slot between the
TrackPoint buttons and the trackpad 1. Slightly pivot the tool downward 2 to release the left and right
TrackPoint buttons. Then, remove the two Trackpoint buttons 3.
4. Loosen the screws that secure the keyboard.
Chapter 7.CRU replacement 57
5. Insert the tabs c and d into the two dents near the two screw heads as shown.
6. Pivot the tool in the direction as shown to release the keyboard 1. Push the keyboard in the direction as
shown by arrows 2 to release the latches from the keyboard bezel.
7. Pivot the keyboard slightly upward 1 and then turn over the keyboard 2.
58 T14s Gen 1 and X13 Gen 1 User Guide
10. Insert the keyboard into the keyboard bezel as shown. Ensure that the top edge of the keyboard (the
edge that is close to the display) is under the keyboard bezel.
11. Slide the keyboard in the direction as shown. Ensure that the latches are secured under the keyboard
frame.
60 T14s Gen 1 and X13 Gen 1 User Guide
62 T14s Gen 1 and X13 Gen 1 User Guide
Chapter 8. Help and support
Frequently asked questions
How do I access Control Panel?Type Control Panel in the Windows search box and then press Enter.
How do I turn off my computer? Open the Start menu and click Power. Then, click Shut down.
How do I partition my storage
drive? https://support.lenovo.com/solutions/ht503851
What do I do if my computer
stops responding.
1. Press and hold the power button until the computer turns off. Then, restart
the computer.
2. If step 1 does not work:
• For models with an emergency reset hole: Insert a straightened paper clip
into the emergency reset hole to cut off power supply temporarily. Then,
restart the computer with ac power connected.
• For models without an emergency reset hole:
– For models with the removable battery, remove the removable battery
and disconnect all power sources. Then, reconnect to ac power and
restart the computer.
– For models with the built-in battery, disconnect all power sources.
Press and hold the power button for about seven seconds. Then,
reconnect to ac power and restart the computer.
What do I do if I spill liquid on the
computer?
1. Carefully unplug the ac power adapter and turn off the computer immediately.
The more quickly you stop the current from passing through the computer the
more likely you will reduce damage from short circuits.
Attention: Although you might lose some data or work by turning off the
computer immediately, leaving the computer on might make your computer
unusable.
2. Do not try to drain out the liquid by turning over the computer. If your
computer has keyboard drainage holes on the bottom, the liquid will be
drained out through the holes.
3. Wait until you are certain that all the liquid is dry before turning on your
computer.
How do I enter the UEFI BIOS
menu?
Restart the computer. When the logo screen is displayed, press F1 to enter the
UEFI BIOS menu.
Where can I get the latest device
drivers and UEFI BIOS?
• From the Vantage app. See “Install a Windows operating system and drivers”
on page 46 and “Update UEFI BIOS” on page 46.
• Download from Lenovo Support Web site at https://pcsupport.lenovo.com.
© Copyright Lenovo 2020, 2021 63
Error messages
If you see a message that is not included in the following table, record the error message first, then shut
down the computer and call Lenovo for help. See “Lenovo Customer Support Center” on page 68.
Message Solution
0190: Critical low-battery error The computer turned off because the battery power is low. Connect the ac power
adapter to the computer and charge the batteries.
0191: System Security - Invalid
remote change requested The system configuration change has failed. Confirm the operation and try again.
0199: System Security - Security
password retry count exceeded.
This message is displayed when you enter a wrong supervisor password more
than three times. Confirm the supervisor password and try again.
0271: Check Date and Time
settings. The date or the time is not set in the computer. Enter the UEFI BIOS menu and set
the date and time.
210x/211x: Detection/Read error
on HDDx/SSDx
The storage drive is not working. Reinstall the storage drive. If the problem still
exists, replace the storage drive.
Error: The non-volatile system
UEFI variable storage is nearly
full.
Note:
This error indicates that the operating system or programs cannot create, modify,
or delete data in the non-volatile system UEFI variable storage due to insufficient
storage space after POST.
The non-volatile system UEFI variable storage is used by the UEFI BIOS and by
the operating system or programs. This error occurs when the operating system
or programs store large amounts of data in the variable storage. All data needed
for POST, such as UEFI BIOS setup settings, chipset, or platform configuration
data, are stored in a separate UEFI variable storage.
Press F1 after the error message is displayed to enter the UEFI BIOS menu. A
dialog asks for confirmation to clean up the storage. If you select “Yes”, all data
that were created by the operating system or programs will be deleted except
global variables defined by the Unified Extensible Firmware Interface
Specification. If you select “No”, all data will be kept, but the operating system or
programs will not be able to create, modify, or delete data in the storage.
If this error happens at a service center, Lenovo authorized service personnel will
clean up the non-volatile system UEFI variable storage using the preceding
solution.
Fan error. Press ESC to startup
with limited performance.
The thermal fan might not work correctly. After the error message is displayed,
press ESC within five seconds to start up the computer with limited performance.
Otherwise, the computer will shut down immediately. If the fan error still exists
when you starts up next time, have your computer serviced.
64 T14s Gen 1 and X13 Gen 1 User Guide
Beep errors
Lenovo SmartBeep technology enables you to decode beep errors with your smartphone when a black
screen occurs with beeps from your computer. To decode the beep error with Lenovo SmartBeep
technology:
1. Go to https://support.lenovo.com/smartbeep or scan the following QR Code.
2. Download the proper diagnostic app and install it on your smartphone.
3. Run the diagnostic app and place the smartphone near the computer.
4. Press Fn on your computer to emit the beep again. The diagnostic app decodes the beep error and
shows possible solutions on the smartphone.
Note: Do not attempt to service a product yourself unless instructed to do so by the Customer Support
Center or product documentation. Only use a Lenovo-authorized service provider to repair your product.
Chapter 8.Help and support 65
Self-help resources
Use the following self-help resources to learn more about the computer and troubleshoot problems.
Resources How to access?
Troubleshooting and FAQ • https://www.lenovo.com/tips
• https://forums.lenovo.com
Accessibility information https://www.lenovo.com/accessibility
Reset or restore Windows
• Use Lenovo recovery options.
1. Go to https://support.lenovo.com/
HowToCreateLenovoRecovery.
2. Follow the on-screen instructions.
• Use Windows recovery options.
1. Go to https://pcsupport.lenovo.com.
2. Detect your computer or manually select your
computer model.
3. Click Diagnostics ➙ Operating System
Diagnostics and then follow the on-screen
instructions.
Use the Vantage app to:
• Configure device settings.
• Download and install UEFI BIOS, drivers, and firmware
updates.
• Secure your computer from outside threats.
• Diagnose hardware problems.
• Check the computer warranty status.
• Access User Guide and helpful articles.
Type Vantage in the search box.
Product documentation:
• Safety and Warranty Guide
• Setup Guide
• This User Guide
• Regulatory Notice
Go to https://pcsupport.lenovo.com. Then, follow the on-
screen instructions to filter out the documentation you
want.
Lenovo Support Web site with the latest support
information of the following:
• Drivers and software
• Diagnostic solutions
• Product and service warranty
• Product and parts details
• Knowledge base and frequently asked questions
https://pcsupport.lenovo.com
Windows help information
• Open the Start menu and click Get Help or Tips.
• Use Windows Search or the Cortana® personal
assistant.
• Microsoft support Web site: https://
support.microsoft.com
66 T14s Gen 1 and X13 Gen 1 User Guide
Windows label
Your computer might have a Windows Genuine Microsoft label affixed to its cover depending on the
following factors:
• Your geographic location
• Edition of Windows that is preinstalled
Go to https://www.microsoft.com/en-us/howtotell/Hardware.aspx for illustrations of the various types of
Genuine Microsoft labels.
• In the People’s Republic of China, the Genuine Microsoft label is required on all computer models
preinstalled with any edition of the Windows operating system.
• In other countries and regions, the Genuine Microsoft label is required only on computer models licensed
for Windows Pro editions.
The absence of a Genuine Microsoft label does not indicate that the preinstalled Windows version is not
genuine. For details on how to tell whether your preinstalled Windows product is genuine, refer to the
information provided by Microsoft at https://www.microsoft.com/en-us/howtotell/default.aspx.
There are no external, visual indicators of the Product ID or Windows version for which the computer is
licensed. Instead, the Product ID is recorded in the computer firmware. Whenever a Windows product is
installed, the installation program checks the computer firmware for a valid, matching Product ID to complete
the activation.
In some cases, an earlier Windows version might be preinstalled under the terms of the Windows Pro edition
license downgrade rights.
Call Lenovo
If you have tried to correct the problem yourself and still need help, you can call Lenovo Customer Support
Center.
Before you contact Lenovo
Prepare the following before you contact Lenovo:
1. Record the problem symptoms and details:
• What is the problem? Is it continuous or intermittent?
• Any error message or error code?
• What operating system are you using? Which version?
• Which software applications were running at the time of the problem?
• Can the problem be reproduced? If so, how?
2. Record the system information:
• Product name
• Machine type and serial number
The following illustration shows where to find the machine type and serial number of your computer.
Chapter 8.Help and support 67
ThinkPad T14s Gen 1
ThinkPad X13 Gen 1
Lenovo Customer Support Center
During the warranty period, you can call Lenovo Customer Support Center for help.
Telephone numbers
For a list of the Lenovo Support phone numbers for your country or region, go to https://
pcsupport.lenovo.com/supportphonelist for the latest phone numbers.
Note: Phone numbers are subject to change without notice. If the number for your country or region is not
provided, contact your Lenovo reseller or Lenovo marketing representative.
68 T14s Gen 1 and X13 Gen 1 User Guide
Services available during the warranty period
• Problem determination - Trained personnel are available to assist you with determining if you have a
hardware problem and deciding what action is necessary to fix the problem.
• Lenovo hardware repair - If the problem is determined to be caused by Lenovo hardware under warranty,
trained service personnel are available to provide the applicable level of service.
• Engineering change management - Occasionally, there might be changes that are required after a product
has been sold. Lenovo or your reseller, if authorized by Lenovo, will make selected Engineering Changes
(ECs) that apply to your hardware available.
Services not covered
• Replacement or use of parts not manufactured for or by Lenovo or nonwarranted parts
• Identification of software problem sources
• Configuration of UEFI BIOS as part of an installation or upgrade
• Changes, modifications, or upgrades to device drivers
• Installation and maintenance of network operating systems (NOS)
• Installation and maintenance of programs
For the terms and conditions of the Lenovo Limited Warranty that apply to your Lenovo hardware product,
go to:
• https://www.lenovo.com/warranty/llw_02
• https://pcsupport.lenovo.com/warrantylookup
Purchase additional services
During and after the warranty period, you can purchase additional services from Lenovo at https://
pcsupport.lenovo.com/warrantyupgrade.
Service availability and service name might vary by country or region.
Chapter 8.Help and support 69
70 T14s Gen 1 and X13 Gen 1 User Guide
Appendix A. Important safety information
Safety notices
This information can help you safely use your computer. Follow and retain all information included with your
computer. The information in this document does not alter the terms of your purchase agreement or the
Limited Warranty. For more information, see Safety and Warranty Guide that comes with your computer.
Customer safety is important. Our products are developed to be safe and effective. However, personal
computers are electronic devices. Power cords, power adapters, and other features can create potential
safety risks that can result in physical injury or property damage, especially if misused. To reduce these risks,
follow the instructions included with your product, observe all warnings on the product and in the operating
instructions, and review the information included in this document carefully. By carefully following the
information contained in this document and provided with your product, you can help protect yourself from
hazards and create a safer computer work environment.
Note: This information includes references to power adapters and batteries. In addition, some products
(such as speakers and monitors) ship with external power adapters. If you have such a product, this
information applies to your product. In addition, computer products contain a coin-sized internal battery that
provides power to the system clock even when the computer is unplugged, so the battery safety information
applies to all computer products.
Important information about using your computer
Ensure that you follow the important tips given here to get the most use and enjoyment out of your computer.
Failure to do so might lead to discomfort or injury, or cause the computer to fail.
Protect yourself from the heat that your computer generates.
When your computer is turned on or the battery is charging, the base,
the palm rest, and some other parts may become hot. The
temperature they reach depends on the amount of system activity and
the level of charge in the battery.
Extended contact with your body, even through clothing, could cause
discomfort or even a skin burn.
• Avoid keeping your hands, your lap, or any other part of your body
in contact with a hot section of the computer for any extended
time.
• Periodically take your hands away from the keyboard by lifting your
hands from the palm rest.
© Copyright Lenovo 2020, 2021 71
Protect yourself from the heat generated by the ac power adapter.
When the ac power adapter is connected to an electrical outlet and
your computer, it generates heat.
Extended contact with your body, even through clothing, may cause a
skin burn.
• Do not place the ac power adapter in contact with any part of your
body while it is in use.
• Never use it to warm your body.
• Do not wrap the cords around the ac power adapter while in use.
Prevent your computer from getting wet.
To avoid spills and the danger of electrical shock, keep liquids away
from your computer.
Protect the cables from being damaged.
Applying strong force to cables may damage or break them.
Route communication lines, or the cables of an ac power adapter, a
mouse, a keyboard, a printer, or any other electronic device, so that
they cannot be walked on, tripped over, pinched by your computer or
other objects, or in any way subject to treatment that could interfere
with the operation of your computer.
Protect your computer and data when moving it.
Before moving a computer equipped with a storage drive, do one of
the following:
• Turn it off.
• Put it in sleep mode.
• Put it in hibernation mode.
This helps to prevent damage to the computer, and possible loss of
data.
72 T14s Gen 1 and X13 Gen 1 User Guide
Handle your computer gently.
Do not drop, bump, scratch, twist, hit, vibrate, push, or place heavy
objects on your computer, display, or external devices.
Carry your computer carefully.
• Use a quality carrying case that provides adequate cushioning and
protection.
• Do not pack your computer in a tightly packed suitcase or bag.
• Before putting your computer in a carrying case, make sure that it
is off, in sleep mode, or in hibernation mode. Do not put a
computer in a carrying case while it is turned on.
Conditions that require immediate action
Products can become damaged due to misuse or neglect. Some product damage is serious enough
that the product should not be used again until it has been inspected and, if necessary, repaired by an
authorized servicer.
As with any electronic device, pay close attention to the product when it is turned on.
On very rare occasions, you might notice an odor or see a puff of smoke or sparks vent from your
product. You might also hear sounds like popping, cracking, or hissing. These might merely mean that
an internal electronic component has failed in a safe and controlled manner. Or, they might indicate a
potential safety issue. Do not take risks or attempt to diagnose the situation yourself. Contact the
Customer Support Center for further guidance. For a list of Service and Support phone numbers, see
the following Web site:
https://pcsupport.lenovo.com/supportphonelist
Frequently inspect your computer and its components for damage, wear, or signs of danger. If you
have any question about the condition of a component, do not use the product. Contact the Customer
Support Center or the product manufacturer for instructions on how to inspect the product and have it
repaired, if necessary.
In the unlikely event that you notice any of the following conditions, or if you have any safety concerns
with your product, stop using the product and unplug it from the power source and
telecommunication lines until you can speak to the Customer Support Center for further guidance.
Appendix A. Important safety information 73
• Power cords, plugs, power adapters, extension cords, surge protectors, or power supplies that are
cracked, broken, or damaged.
• Signs of overheating, smoke, sparks, or fire.
• Damage to a battery (such as cracks, dents, or creases), discharge from a battery, or a buildup of foreign
substances on the battery.
• A cracking, hissing, or popping sound, or strong odor that comes from the product.
• Signs that liquid has been spilled or an object has fallen onto the computer product, the power cord, or
power adapter.
• The computer product, power cord, or power adapter has been exposed to water.
• The product has been dropped or damaged in any way.
• The product does not operate normally when you follow the operating instructions.
Note: If you notice these conditions with a product (such as an extension cord) that is not manufactured for
or by Lenovo, stop using that product until you can contact the product manufacturer for further instructions,
or until you get a suitable replacement.
Service and upgrades
Do not attempt to service a product yourself unless instructed to do so by the Customer Support Center or
your documentation. Only use a Service Provider who is approved to repair your particular product.
Note: Some computer parts can be upgraded or replaced by the customer. Upgrades typically are referred
to as options. Replacement parts approved for customer installation are referred to as Customer
Replaceable Units, or CRUs. Lenovo provides documentation with instructions when it is appropriate for
customers to install options or replace CRUs. You must closely follow all instructions when installing or
replacing parts. The Off state of a power indicator does not necessarily mean that voltage levels inside a
product are zero. Before you remove the covers from a product equipped with a power cord, always ensure
that the power is turned off and that the product is unplugged from any power source. If you have any
questions or concerns, contact the Customer Support Center.
Although there are no moving parts in your computer after the power cord has been disconnected, the
following warnings are required for your safety.
Keep fingers and other parts of your body away from hazardous, moving parts. If you suffer an injury, seek
medical care immediately.
Do not touch hot surface of hot components inside the computer. During operation, some components
become hot enough to burn the skin. Before you open the computer cover, turn off the computer, disconnect
power, and wait approximately 10 minutes for the components to cool.
After replacing a CRU, reinstall all protective covers, including the computer cover, before connecting power
and operating the computer. This action is important to help prevent unexpected electrical shock and help
ensure the containment of an unexpected fire that could happen under extremely rare conditions.
74 T14s Gen 1 and X13 Gen 1 User Guide
When replacing CRUs, be cautious of sharp edges or corners that might cause injury. If you suffer an injury,
seek medical care immediately.
Power cords and power adapters
DANGER
Use only the power cords and power adapters supplied by the product manufacturer.
The power cords shall be safety approved. For Germany, it shall be H03VV-F, 3G, 0.75 mm2, or
better. For other countries, the suitable types shall be used accordingly.
Never wrap a power cord around a power adapter or other object. Doing so can stress the cord in
ways that can cause the cord to fray, crack, or crimp. This can present a safety hazard.
Always route power cords so that they will not be walked on, tripped over, or pinched by objects.
Protect power cords and power adapters from liquids. For instance, do not leave your power cord
or power adapter near sinks, tubs, toilets, or on floors that are cleaned with liquid cleansers. Liquids
can cause a short circuit, particularly if the power cord or power adapter has been stressed by
misuse. Liquids also can cause gradual corrosion of power cord terminals and/or the connector
terminals on a power adapter, which can eventually result in overheating.
Ensure that all power cord connectors are securely and completely plugged into receptacles.
Do not use any power adapter that shows corrosion at the ac input pins or shows signs of
overheating (such as deformed plastic) at the ac input pins or anywhere on the power adapter.
Do not use any power cords where the electrical contacts on either end show signs of corrosion or
overheating or where the power cord appears to have been damaged in any way.
To prevent possible overheating, do not cover the power adapter with clothing or other objects
when the power adapter is plugged into an electrical outlet.
Extension cords and related devices
Ensure that extension cords, surge protectors, uninterruptible power supplies, and power strips that you use
are rated to handle the electrical requirements of the product. Never overload these devices. If power strips
are used, the load should not exceed the power strip input rating. Consult an electrician for more information
if you have questions about power loads, power requirements, and input ratings.
Appendix A. Important safety information 75
Plugs and outlets
DANGER
If a receptacle (power outlet) that you intend to use with your computer equipment appears to be
damaged or corroded, do not use the outlet until it is replaced by a qualified electrician.
Do not bend or modify the plug. If the plug is damaged, contact the manufacturer to obtain a
replacement.
Do not share an electrical outlet with other home or commercial appliances that draw large
amounts of electricity; otherwise, unstable voltage might damage your computer, data, or attached
devices.
Some products are equipped with a three-pronged plug. This plug fits only into a grounded
electrical outlet. This is a safety feature. Do not defeat this safety feature by trying to insert it into a
non-grounded outlet. If you cannot insert the plug into the outlet, contact an electrician for an
approved outlet adapter or to replace the outlet with one that enables this safety feature. Never
overload an electrical outlet. The overall system load should not exceed 80 percent of the branch
circuit rating. Consult an electrician for more information if you have questions about power loads
and branch circuit ratings.
Be sure that the power outlet you are using is properly wired, easily accessible, and located close to
the equipment. Do not fully extend power cords in a way that will stress the cords.
Be sure that the power outlet provides the correct voltage and current for the product you are
installing.
Carefully connect and disconnect the equipment from the electrical outlet.
Power supply statement
Never remove the cover on a power supply or any part that has the following label attached.
Hazardous voltage, current, and energy levels are present inside any component that has this label attached.
There are no serviceable parts inside these components. If you suspect a problem with one of these parts,
contact a service technician.
External devices
CAUTION:
Do not connect or disconnect any external device cables other than Universal Serial Bus (USB) and
1394 cables while the computer power is on; otherwise, you might damage your computer. To avoid
possible damage to attached devices, wait at least five seconds after the computer is shut down to
disconnect external devices.
76 T14s Gen 1 and X13 Gen 1 User Guide
General battery notice
DANGER
Batteries supplied by Lenovo for use with your product have been tested for compatibility and
should only be replaced with approved parts. A battery other than the one specified by Lenovo, or a
disassembled or modified battery is not covered by the warranty.
Battery abuse or mishandling can cause overheat, liquid leakage, or an explosion. To avoid possible
injury:
• Do not open, dissemble, or service any battery.
• Do not crush or puncture the battery.
• Do not short-circuit the battery, or expose it to water or other liquids.
• Keep the battery away from children.
• Keep the battery away from fire.
Stop using the battery if it is damaged, or if you notice any discharge or the buildup of foreign
materials on the battery leads.
Store the rechargeable batteries or products containing the rechargeable batteries at room
temperature, charged to approximately 30 to 50% of capacity. We recommend that the batteries be
charged about once per year to prevent overdischarge.
Do not put the battery in trash that is disposed of in landfills. When disposing of the battery, comply
with local ordinances or regulations.
Notice for built-in rechargeable battery
DANGER
Do not attempt to remove or replace the built-in rechargeable battery. Replacement of the battery
must be done by a Lenovo-authorized repair facility or technician.
Only recharge the battery strictly according to instructions included in the product documentation.
The Lenovo-authorized repair facilities or technicians recycle Lenovo batteries according to local
laws and regulations.
Lithium coin-cell battery notice
DANGER
Danger of explosion if battery is incorrectly replaced.
If the coin-cell battery is not a CRU, do not attempt to replace the coin-cell battery. Replacement of
the battery must be done by a Lenovo-authorized repair facility or technician.
Appendix A. Important safety information 77
The Lenovo-authorized repair facilities or technicians recycle Lenovo batteries according to local
laws and regulations.
When replacing the lithium coin-cell battery, use only the same type or equivalent type that is recommended
by the manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed
of. Swallowing the lithium coin-cell battery will cause chocking or severe internal burns in just two hours and
might even result in death.
Keep batteries away from children. If the lithium coin-cell battery is swallowed or placed inside any part of
the body, seek medical care immediately.
Do not:
• Throw or immerse into water
• Heat to more than 100 °C (212°F)
• Repair or disassemble
• Leave in an extremely low air pressure environment
• Leave in an extremely high-temperature environment
• Crush, puncture, cut, or incinerate
Dispose of the battery as required by local ordinances or regulations.
The following statement applies to users in the state of California, U.S.A.
California Perchlorate Information:
Products containing manganese dioxide lithium coin-cell batteries may contain perchlorate.
Perchlorate Material - special handling may apply, see https://www.dtsc.ca.gov/hazardouswaste/
perchlorate/.
78 T14s Gen 1 and X13 Gen 1 User Guide
Heat and product ventilation
DANGER
Computers, ac power adapters, and many accessories can generate heat when turned on and when
batteries are charging. Notebook computers can generate a significant amount of heat due to their
compact size. Always follow these basic precautions:
• When your computer is turned on or the battery is charging, the base, the palm rest, and some
other parts may become hot. Avoid keeping your hands, your lap, or any other part of your body
in contact with a hot section of the computer for any extended length of time. When you use the
keyboard, avoid keeping your palms on the palm rest for a prolonged period of time. Your
computer generates some heat during normal operation. The amount of heat depends on the
amount of system activity and the battery charge level. Extended contact with your body, even
through clothing, could cause discomfort or even a skin burn. Periodically take breaks from using
the keyboard by lifting your hands from the palm rest; and be careful not to use the keyboard for
any extended length of time.
• Do not operate your computer or charge the battery near flammable materials or in explosive
environments.
• Ventilation slots, fans and/or heat sinks are provided with the product for safety, comfort, and
reliable operation. These features might inadvertently become blocked by placing the product on
a bed, sofa, carpet, or other flexible surface. Never block, cover, or disable these features.
• When the ac power adapter is connected to an electrical outlet and your computer, it generates
heat. Do not place the adapter in contact with any part of your body while using it. Never use the
ac power adapter to warm your body. Extended contact with your body, even through clothing,
may cause a skin burn.
For your safety, always follow these basic precautions with your computer:
• Keep the cover closed whenever the computer is plugged in.
• Regularly inspect the outside of the computer for dust accumulation.
• Remove dust from vents and any perforations in the bezel. More frequent cleanings might be
required for computers in dusty or high-traffic areas.
• Do not restrict or block any ventilation openings.
• Do not operate your computer inside furniture, as this might increase the risk of overheating.
• Airflow temperatures into the computer should not exceed 35°C (95°F).
Appendix A. Important safety information 79
Electrical current safety information
DANGER
Electric current from power, telephone, and communication cables is hazardous.
To avoid a shock hazard:
• Do not use your computer during a lightning storm.
• Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration
of this product during an electrical storm.
• Connect all power cords to a properly wired and grounded electrical outlet.
• Connect properly wired outlets to any equipment that will be attached to this product.
• Whenever possible, use one hand only to connect or disconnect signal cables.
• Never turn on any equipment when there is evidence of fire, water, or structural damage.
• Disconnect the attached power cords, battery, and all the cables before you open the device
covers, unless instructed otherwise in the installation and configuration procedures.
• Do not use your computer until all internal parts enclosures are fastened into place. Never use
the computer when internal parts and circuits are exposed.
DANGER
Connect and disconnect cables as described in the following procedures when installing, moving,
or opening covers on this product or attached devices.
To connect:
1. Turn everything OFF.
2. First, attach all cables to devices.
3. Attach signal cables to connectors.
4. Attach power cords to outlets.
5. Turn devices ON.
To disconnect:
1. Turn everything OFF.
2. First, remove power cords from outlets.
3. Remove signal cables from connectors.
4. Remove all cables from devices.
The power cord must be disconnected from the wall outlet or receptacle before installing all other electrical
cables connected to the computer.
The power cord may be reconnected to the wall outlet or receptacle only after all other electrical cables have
been connected to the computer.
DANGER
During electrical storms, do not perform any replacement and do not connect the telephone cable
to or disconnect it from the telephone outlet on the wall.
80 T14s Gen 1 and X13 Gen 1 User Guide
Liquid crystal display (LCD) notice
CAUTION:
The liquid crystal display (LCD) is made of glass, and rough handling or dropping the computer can
cause the LCD to break. If the LCD breaks and the internal fluid gets into your eyes or on your hands,
immediately wash the affected areas with water for at least 15 minutes; if any symptoms are present
after washing, get medical care.
Note: For products with mercury-containing fluorescent lamps (for example, non-LED), the fluorescent lamp
in the liquid crystal display (LCD) contains mercury; dispose of according to local, state, or federal laws.
Use earphones, headphones, or a headset
Excessive sound pressure from earphones and headphones can cause hearing loss. Adjustment of the
equalizer to maximum increases the earphone and headphone output voltage and the sound pressure level.
Therefore, to protect your hearing, adjust the equalizer to an appropriate level.
Excessive use of headphones or earphones for a long period of time at high volume can be dangerous if the
output of the headphone or earphone connectors do not comply with specifications of EN 50332-2. The
headphone output connector of your computer complies with EN 50332-2 Sub clause 7. This specification
limits the computer’s maximum wide band true RMS output voltage to 150 mV. To help protect against
hearing loss, ensure that the headphones or earphones you use also comply with EN 50332-2 (Clause 7
limits) for a wide band characteristic voltage of 75 mV. Using headphones that do not comply with EN 50332-
2 can be dangerous due to excessive sound pressure levels.
If your Lenovo computer came with headphones or earphones in the packaging, as a set, the combination of
the headphones or earphones and the computer already complies with the specifications of EN 50332-1. If
different headphones or earphones are used, ensure that they comply with EN 50332-1 (Clause 6.5
Limitation Values). Using headphones that do not comply with EN 50332-1 can be dangerous due to
excessive sound pressure levels.
Choking hazard notice
CHOKING HAZARD – Product contains small parts.
Keep away from children under three years.
Plastic bag notice
DANGER
Plastic bags can be dangerous. Keep plastic bags away from babies and children to avoid danger of
suffocation.
Appendix A. Important safety information 81
Glass parts notice
CAUTION:
Some parts of your product may be made of glass. This glass could break if the product is dropped on
a hard surface or receives a substantial impact. If glass breaks, do not touch or attempt to remove it.
Stop using your product until the glass is replaced by trained service personnel.
Static electricity prevention
Static electricity, although harmless to you, can seriously damage computer components and options.
Improper handling of static-sensitive parts can damage the part. When you unpack an option or CRU, do not
open the static-protective package containing the part until the instructions direct you to install it.
When you handle options or CRUs, or perform any work inside the computer, take the following precautions
to avoid static-electricity damage:
• Limit your movement. Movement can cause static electricity to build up around you.
• Always handle components carefully. Handle adapters, memory modules, and other circuit boards by the
edges. Never touch exposed circuitry.
• Prevent others from touching components.
• When you install a static-sensitive option or CRU, touch the static-protective packaging containing the
part to a metal expansion-slot cover or other unpainted metal surface on the computer for at least two
seconds. This reduces static electricity in the package and your body.
• When possible, remove the static-sensitive part from the static-protective packaging and install the part
without setting it down. When this is not possible, place the static-protective packaging on a smooth, level
surface and place the part on it.
• Do not place the part on the computer cover or other metal surface.
Operating environment
Maximum altitude (without pressurization)
3048 m (10 000 ft)
Temperature
• Operating: 5°C to 35°C (41°F to 95°F)
• Storage and transportation in original shipping packaging: -20°C to 60°C (-4°F to 140°F)
• Storage without packaging: 5°C to 43°C (41°F to 109°F)
Note: When you charge the battery, its temperature must be no lower than 10°C (50°F).
Relative humidity
• Operating: 8% to 95% at wet-bulb temperature 23°C (73°F)
• Storage and transportation: 5% to 95% at wet-bulb temperature 27°C (81°F)
Cleaning and maintenance
With appropriate care and maintenance, your computer will serve you reliably. The following topics offer
information to help you keep your computer working with best performance.
82 T14s Gen 1 and X13 Gen 1 User Guide
Basic maintenance tips
Here are some basic points about keeping your computer functioning properly:
• If possible, place your computer in a well-ventilated and dry area without direct exposure to sunshine.
• Store packing materials safely out of the reach of children to prevent the risk of suffocation from plastic
bags.
• Keep your computer away from magnets, activated cellular phones, electrical appliances, or speakers
(more than 13 cm or 5 inches).
• Avoid subjecting your computer to extreme temperatures (below 5°C/41°F or above 35°C/95°F).
• Avoid placing any objects (including paper) between the display and the keyboard or the palm rest.
• Computer display might be designed to be opened and used at a certain angle. Do not open the display
with force. Otherwise, the computer hinge might get damaged.
• Do not turn your computer over when the ac power adapter is plugged in, otherwise, it could break the
adapter plug.
• Before moving your computer, be sure to remove any media, turn off attached devices, and disconnect
cords and cables.
• When picking up your open computer, hold it by the bottom. Do not pick up or hold your computer by the
display.
• Only an authorized Lenovo repair technician should disassemble and repair your computer.
• Do not modify or tape the latches to keep the display open or closed.
• Avoid directly exposing your computer and peripherals to the air from an appliance that can produce
negative ions. Wherever possible, ground your computer to facilitate safe electrostatic discharge.
Clean your computer
It is a good practice to clean your computer periodically to protect the surfaces and ensure trouble-free
operation.
Clean the computer cover: Wipe it with a lint-free cloth dampened in mild soap and water. Avoid applying
liquids directly to the cover.
Clean the keyboard: Wipe the keys one by one with a lint-free cloth dampened in mild soap and water. If
you wipe several keys at a time, the cloth might hook onto an adjacent key and possibly damage it. Avoid
spraying cleaner directly onto the keyboard. To remove any crumbs or dust from beneath the keys, you can
use a camera blower with a brush or use cool air from a hair dryer.
Clean the computer screen: Scratches, oil, dust, chemicals, and ultraviolet light can affect the performance
of your computer screen. Use a dry, soft lint-free cloth to wipe the screen gently. If you see a scratchlike
mark on your screen, it might be a stain. Wipe or dust the stain gently with a soft, dry cloth. If the stain
remains, moisten a soft, lint-free cloth with water or eyeglass cleaner, but do not apply liquids directly to your
computer screen. Ensure that the computer screen is dry before closing it.
Appendix A. Important safety information 83
84 T14s Gen 1 and X13 Gen 1 User Guide
Appendix B. Accessibility and ergonomic information
This chapter provides information about accessibility and ergonomics.
Accessibility information
Lenovo is committed to providing users who have hearing, vision, and mobility limitations with greater
access to information and technology. You can get the most up-to-date accessibility information from
https://www.lenovo.com/accessibility.
If you need additional support with the accessibility features, go to https://pcsupport.lenovo.com/
supportphonelist to find the support phone numbers for your country or region.
Ergonomic information
Good ergonomic practice is important to get the most from your personal computer and to avoid discomfort.
Arrange your workplace and the equipment you use to suit your individual needs and the kind of work that
you perform. In addition, use healthy work habits to maximize your performance and comfort when using
your computer.
Working in the virtual office might mean adapting to frequent changes in your environment. Adapting to the
surrounding light sources, active seating, and the placement of your computer hardware, can help you
improve your performance and achieve greater comfort.
This example shows someone in a conventional setting. Even when not in such a setting, you can follow
many of these tips. Develop good habits, and they will serve you well.
General posture: Make minor modifications in your working posture to deter the onset of discomfort caused
by long periods of working in the same position. Frequent short breaks from your work also help to prevent
minor discomfort associated with your working posture.
Display: Position the display to maintain a comfortable viewing distance of 510 mm to 760 mm (20 inches to
30 inches). Avoid glare or reflections on the display from overhead lighting or outside sources of light. Keep
the display screen clean and set the brightness to levels that enable you to see the screen clearly. Press the
brightness control keys to adjust display brightness.
Head position: Keep your head and neck in a comfortable and neutral (vertical, or upright) position.
Chair: Use a chair that gives you good back support and seat height adjustment. Use chair adjustments to
best suit your comfort posture.
© Copyright Lenovo 2020, 2021 85
Arm and hand position: If available, use chair arm rests or an area on your working surface to provide
weight support for your arms. Keep your forearms, wrists, and hands in a relaxed and neutral (horizontal)
position. Type with a soft touch without pounding the keys.
Leg position: Keep your thighs parallel to the floor and your feet flat on the floor or on a footrest.
What if you are traveling?
It might not be possible to observe the best ergonomic practices when you are using your computer while on
the move or in a casual setting. Regardless of the setting, try to observe as many of the tips as possible.
Sitting properly and using adequate lighting, for example, helps you maintain desirable levels of comfort and
performance. If your work area is not in an office setting, ensure to take special note of employing active
sitting and taking work breaks. Many product solutions are available to help you modify and expand your
computer to best suit your needs. You can find some of these options at https://www.lenovo.com/accessories.
Explore your options for docking solutions and external products that provide the adjustability and features
that you want.
Questions about vision?
The visual display screens of notebook computers are designed to meet the highest standards. These visual
display screens provide you with clear, crisp images and large, bright displays that are easy to see, yet easy
on the eyes. Any concentrated and sustained visual activity can be tiring. If you have questions on eye
fatigue or visual discomfort, consult a vision-care specialist for advice.
86 T14s Gen 1 and X13 Gen 1 User Guide
Appendix C. Supplemental information about the Linux
operating system
In limited countries or regions, Lenovo offers customers an option to order computers with the preinstalled
Linux® operating system.
If the Linux operating system is available on your computer, read the following information before you use the
computer. Ignore any information related to Windows-based programs, utilities, and Lenovo preinstalled
applications in this documentation.
Access the Lenovo Limited Warranty
This product is covered by the terms of the Lenovo Limited Warranty (LLW), version L505-0010-02 08/2011.
You can view the LLW in a number of languages from the following Web site. Read the Lenovo Limited
Warranty at:
https://www.lenovo.com/warranty/llw_02
The LLW also is preinstalled on the computer. To access the LLW:
• for Ubuntu®, go to /usr/share/doc/lenovo-doc
• for Fedora®, go to /opt/Lenovo
If you cannot view the LLW either from the Web site or from your computer, contact your local Lenovo office
or reseller to obtain a printed version of the LLW.
Access Linux distributions
Linux is an open-source operating system, and popular Linux distributions include Ubuntu and Fedora.
To learn more about the Ubuntu operating system, go to:
https://www.ubuntu.com
To learn more about the Fedora operating system, go to:
https://getfedora.org/
Get support information
If you need help, service, technical assistance, or more information about the Linux operating system or
other applications, contact the provider of the Linux operating system or the provider of the application. If
you need the service and support for hardware components shipped with your computer, contact Lenovo.
For more information about how to contact Lenovo, refer to the User Guide and Safety and Warranty Guide.
To access the latest User Guide and Safety and Warranty Guide, go to:
https://pcsupport.lenovo.com
© Copyright Lenovo 2020, 2021 87
88 T14s Gen 1 and X13 Gen 1 User Guide
Appendix D. Compliance and TCO Certified information
This chapter provides regulatory, environmental, RoHS, and ENERGY STAR information about Lenovo
products.
Radio frequency compliance statements
Computer models equipped with wireless communications comply with the radio frequency and safety
standards of any country or region in which it has been approved for wireless use.
Besides this document, ensure that you read the Regulatory Notice for your country or region before using
the wireless devices contained in your computer.
Wireless-related information
This topic provides wireless-related information about Lenovo products.
Wireless interoperability
Wireless-LAN card is designed to be interoperable with any wireless-LAN product that is based on Direct
Sequence Spread Spectrum (DSSS), Complementary Code Keying (CCK), and/or Orthogonal Frequency
Division Multiplexing (OFDM) radio technology, and/or Orthogonal Frequency Division Multiplexing Access
(OFDMA) and is compliant to:
• The 802.11b/g Standard, 802.11a/b/g, 802.11n, 802.11ac, or 802.11ax on wireless-LANs, as defined and
approved by the Institute of Electrical and Electronics Engineers.
• The Wireless Fidelity (Wi-Fi®) certification as defined by the Wi-Fi Alliance®.
Usage environment and your health
This computer contains integrated wireless cards that operate within the guidelines identified by radio
frequency (RF) safety standards and recommendations; therefore, Lenovo believes that this product is safe
for use by consumers. These standards and recommendations reflect the consensus of the worldwide
scientific community, and result from deliberations of panels and committees of scientists, who continually
review and interpret the extensive research literature.
In some situations or environments, the use of wireless devices might be restricted by the proprietor of a
building or responsible representatives of an organization. For example, these situations and areas might
include the following:
• On board of airplanes, in hospitals or near petrol stations, blasting areas (with electro-explosive devices),
medical implants or body-worn electronic medical devices, such as pace makers.
• In any other environment where the risk of interference to other devices or services is perceived or
identified as harmful.
If you are uncertain of the policy that applies to the use of wireless devices in a specific area (such as an
airport or hospital), you are encouraged to ask for authorization to use a wireless device prior to turning on
the computer.
Locate the UltraConnect wireless antennas
Your computer has an UltraConnect™ wireless antenna system. You can enable wireless communication
wherever you are.
© Copyright Lenovo 2020, 2021 89
The following illustration shows the antenna locations on your computer:
1 Wireless LAN antenna (main)
2 Wireless WAN antenna (main, for selected models)
3 Wireless WAN antenna (auxiliary, for selected models)
4 Wireless LAN antenna (auxiliary)
Locate wireless regulatory notices
For more information about the wireless regulatory notices, refer to the Regulatory Notice at https://
support.lenovo.com.
European Union (EU) / United Kingdom (UK) — Radio Equipment
Compliance
EU Contact: Lenovo (Slovakia), Landererova 12, 811 09 Bratislava, Slovakia
UK contact: Lenovo, Redwood, Crockford Lane, Basingstoke, RG24 8WQ, UK.
This product is in conformity with all the requirements and essential norms that apply to EU Council Radio
Equipment Directive 2014/53/EU on the approximation of the laws of the Member States, as well as the UK
Radio Equipment Regulations SI 2017 No. 1206, relating to radio equipment.
The full text of the system EU declaration of conformity is available at:
https://www.lenovo.com/us/en/compliance/eu-doc
The full text of the system UK declaration of conformity is available at:
https://www.lenovo.com/us/en/compliance/uk-doc
Lenovo cannot accept responsibility for any failure to satisfy the protection requirements resulting from a
non-recommended modification of the product, including the installation of option cards from other
manufacturers. This product has been tested and found to comply with the limits for Class B equipment
according to European and UK compliance standards. The limits for Class B equipment were derived for
90 T14s Gen 1 and X13 Gen 1 User Guide
typical residential environments to provide reasonable protection against interference with certified
communication devices.
Brazil
Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência
em sistemas devidamente autorizados.
This equipment is not protected against harmful interference and may not cause interference with duly
authorized systems.
Mexico
Advertencia: En Mexico la operación de este equipo está sujeta a las siguientes dos condiciones: (1) es
posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe
aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.
Singapore
Korea radio frequency compliance statement
무선설비 전파 혼신 (사용주파수 2400∼2483.5 , 5725∼5825 무선제품해당)
해당 무선설비가 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없음
SAR 정보
본 장치는 전파 노출에 대한 가이드라인을 충족합니다.
본 장치는 무선 송수신기 입니다. 본 장치는 국제 가이드라인으로 권장되는 전파 노출에 대한 제한을 초과하지
않도록 설계되었습니다. 장치 액세서리 및 최신 부품을 사용할 경우 SAR 값이 달라질 수 있 습니다. SAR 값은
국가 보고 및 테스트 요구 사항과 네트워크 대역에 따라 다를 수 있습니다. 본 장치 는 사람의 신체에서 20mm
이상의 거리에서 사용할 수 있습니다.
Environmental information of countries and regions
This section provides environmental, recycling, and RoHS information about Lenovo products.
Recycling and environmental information
Lenovo encourages owners of information technology (IT) equipment to responsibly recycle their equipment
when it is no longer needed. Lenovo offers a variety of programs and services to assist equipment owners in
recycling their IT products. For information about recycling Lenovo products, go to:
https://www.lenovo.com/recycling
The latest environmental information about our products is available at:
Appendix D. Compliance and TCO Certified information 91
https://www.lenovo.com/ecodeclaration
Important battery recycling and WEEE information
Take back and recycling information for WEEE and batteries/accumulators in the European Union and the
United Kingdom
The crossed-out wheeled bin marking applies only to countries with WEEE and batteries waste regulations
including the European Union (EU), and United Kingdom (UK).
Appliances and batteries/accumulators are labeled in accordance with local regulations concerning waste
electrical and electronic equipment (WEEE) and waste batteries and waste accumulators. These regulations
determine the framework for the return and recycling of used appliances and used batteries/accumulators as
applicable within each geography. This label is applied to various products to indicate that the product is not
to be thrown away, but rather put in the established collection systems for reclaiming these end of life
products.
The label on the battery may also include a chemical symbol for the metal concerned in the battery (Pb for
lead, Hg for mercury, and Cd for cadmium).
Users of electrical and electronic equipment (EEE) and users of batteries/accumulators with the crossed-out
wheeled bin marking must not dispose of end of life products as unsorted municipal waste, but use the
collection framework available to them for the return, recycle, and recovery of WEEE and waste batteries/
accumulators and to minimize any potential effects of EEE and batteries on the environment and human
health due to the presence of hazardous substances.
Lenovo electrical and electronic equipment (EEE) may contain parts and components, which at end-of-life
might qualify as hazardous waste.
EEE and waste electrical and electronic equipment (WEEE) can be delivered free of charge to the place of
sale or any distributor that sells electrical and electronic equipment of the same nature and function as the
used EEE or WEEE.
Before placing electrical and electronic equipment (EEE) in the waste collection stream or in waste collection
facilities, the end user of equipment containing batteries and/or accumulators must remove those batteries
and accumulators for separate collection.
Dispose of lithium batteries and battery packs from Lenovo products:
A coin-cell type lithium battery might be installed inside your Lenovo product. You can find details about the
battery in the product documentation. If the battery needs to be replaced, contact your place of purchase or
contact Lenovo for service. If you need to dispose of a lithium battery, insulate it with vinyl tape, contact your
place of purchase or a waste-disposal operator, and follow their instructions.
Your Lenovo device might contain a lithium-ion battery pack or a nickel metal hydride battery pack. You can
find details on the battery pack in the product documentation. If you need to dispose of a battery pack,
insulate it with vinyl tape, contact Lenovo sales, service, or your place of purchase, or a waste-disposal
operator, and follow their instructions. You also can refer to the instructions provided in the user guide for
your product.
For proper collection and treatment, go to:
92 T14s Gen 1 and X13 Gen 1 User Guide
https://www.lenovo.com/environment
For additional WEEE information, go to:
https://www.lenovo.com/recycling
WEEE information for Hungary
Lenovo, as a producer, bears the cost incurred in connection with the fulfillment of Lenovo’s obligations
under Hungary Law No. 197/2014 (VIII.1.) subsections (1)-(5) of section 12.
Japan recycling statements
Collect and recycle a disused Lenovo computer or monitor
If you are a company employee and need to dispose of a Lenovo computer or monitor that is the property of
the company, you must do so in accordance with the Law for Promotion of Effective Utilization of Resources.
Computers and monitors are categorized as industrial waste and should be properly disposed of by an
industrial waste disposal contractor certified by a local government. In accordance with the Law for
Promotion of Effective Utilization of Resources, Lenovo Japan provides, through its PC Collecting and
Recycling Services, for the collecting, reuse, and recycling of disused computers and monitors. For details,
visit the Lenovo Web site at:
https://www.lenovo.com/recycling/japan
Pursuant to the Law for Promotion of Effective Utilization of Resources, the collecting and recycling of home-
used computers and monitors by the manufacturer was begun on October 1, 2003. This service is provided
free of charge for home-used computers sold after October 1, 2003. For details, go to:
https://www.lenovo.com/recycling/japan
Dispose of Lenovo computer components
Some Lenovo computer products sold in Japan may have components that contain heavy metals or other
environmental sensitive substances. To properly dispose of disused components, such as a printed circuit
board or drive, use the methods described above for collecting and recycling a disused computer or monitor.
Dispose of disused lithium batteries from Lenovo computers
A button-shaped lithium battery is installed inside your Lenovo computer to provide power to the computer
clock while the computer is off or disconnected from the main power source. If you need to replace it with a
new one, contact your place of purchase or contact Lenovo for service. If you need to dispose of a disused
lithium battery, insulate it with vinyl tape, contact your place of purchase or an industrial-waste-disposal
operator, and follow their instructions.
Disposal of a lithium battery must comply with local ordinances and regulations.
Dispose of a disused battery from Lenovo notebook computers
Your Lenovo notebook computer has a lithium ion battery or a nickel metal hydride battery. If you are a
company employee who uses a Lenovo notebook computer and need to dispose of a battery, contact the
proper person in Lenovo sales, service, or marketing, and follow that person's instructions. You also can
refer to the instructions at:
https://www.lenovo.com/jp/ja/environment/recycle/battery/
Appendix D. Compliance and TCO Certified information 93
If you use a Lenovo notebook computer at home and need to dispose of a battery, you must comply with
local ordinances and regulations. You also can refer to the instructions at:
https://www.lenovo.com/jp/ja/environment/recycle/battery/
Recycling information for Brazil
Declarações de Reciclagem no Brasil
Descarte de um Produto Lenovo Fora de Uso
Equipamentos elétricos e eletrônicos não devem ser descartados em lixo comum, mas enviados à pontos de
coleta, autorizados pelo fabricante do produto para que sejam encaminhados e processados por empresas
especializadas no manuseio de resíduos industriais, devidamente certificadas pelos orgãos ambientais, de
acordo com a legislação local.
A Lenovo possui um canal específico para auxiliá-lo no descarte desses produtos. Caso você possua um
produto Lenovo em situação de descarte, ligue para o nosso SAC ou encaminhe um e-mail para:
reciclar@lenovo.com, informando o modelo, número de série e cidade, a fim de enviarmos as instruções
para o correto descarte do seu produto Lenovo.
Recycling information for mainland China
Battery recycling information for Taiwan
Battery recycling information for the United States and Canada
94 T14s Gen 1 and X13 Gen 1 User Guide
Restriction of Hazardous Substances (RoHS) Directive of countries and
regions
The latest environmental information about Lenovo products is available at:
https://www.lenovo.com/ecodeclaration
European Union (EU) / United Kingdom (UK) RoHS
This Lenovo product, with included parts (cables, cords, and so on) meets the requirements of EU Directive
2011/65/EU (as amended by Directive 2015/863/EU) and UK SI 2012 No. 3032 on the restriction of the use of
certain hazardous substances in electrical and electronic equipment ("RoHS recast" or "RoHS 2").
For more information about Lenovo worldwide compliance on RoHS, go to:
https://www.lenovo.com/rohs-communication
Turkish WEEE / RoHS
Ukraine RoHS
India RoHS
RoHS compliant as per E-Waste (Management) Rules.
Mainland China RoHS
The information in the following table is applicable to products manufactured on or after January 1, 2015 for
sale in the People’s Republic of China.
Appendix D. Compliance and TCO Certified information 95
96 T14s Gen 1 and X13 Gen 1 User Guide
Taiwan RoHS
Electromagnetic emission notices
Federal Communications Commission (FCC) Supplier’s Declaration of
Conformity
Notes:
• The statements below regarding FCC are only valid for products that are shipping to the United States.
• Refer to the product label information to identify the specific model name and number of your product.
The following information refers to ThinkPad T14s Gen 1 and ThinkPad X13 Gen 1.
Appendix D. Compliance and TCO Certified information 97
Product name Machine types
ThinkPad T14s Gen 1 20T0, 20T1, 20UH and 20UJ
ThinkPad X13 Gen 1 20T2, 20T3, 20UF and 20UG
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult an authorized dealer or service representative for help.
Lenovo is not responsible for any radio or television interference caused by using other than recommended
cables and connectors or by unauthorized changes or modifications to this equipment. Unauthorized
changes or modifications could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Responsible Party:
Lenovo (United States) Incorporated
7001 Development Drive
Morrisville, NC 27560
Email: FCC@lenovo.com
FCC ID and IC Certification information
You can find the FCC and IC Certification information through one of the following methods:
• Through an electronic-label screen (E-label screen) preinstalled on your computer. To view the E-label
screen, see “Regulatory labels” on page 100.
• On a physical label attached to the outside of your computer shipping carton.
Industry Canada compliance statement
CAN ICES-003(B)/NMB-003(B)
European Union / United Kingdom (UK) conformity
European Union (EU) / United Kingdom (UK) — Electromagnetic Compatibility Compliance
This product is in conformity with the protection requirements of EU Council Directive 2014/30/EU on the
approximation of the laws of the Member States, as well as UK SI 2016 No. 1091 with amendments, relating
98 T14s Gen 1 and X13 Gen 1 User Guide
to the electromagnetic compatibility limits for Class B equipment. These Class B requirements are intended
to offer adequate protection to broadcast services within residential environments.
EU ErP (EcoDesign) Directive (2009/125/EC) - external power adapters (Regulation (EU) 2019/1782),
Ecodesign for Energy-Related Products Regulations 2010 - UK SI 2010 No. 2617 (Ext PSU), SI 2020 No.
485 (Ntwk Standby), SI 2014 No. 1290 as amended
Lenovo products are compliant with the EU EcoDesign (ErP) Directive and UK EcoDesign for Energy-related
Products Regulations. Refer to the following for details. For EU, refer to the system declaration https://
www.lenovo.com/us/en/compliance/eu-doc, and for UK refer to the system declaration https://
www.lenovo.com/us/en/compliance/uk-doc.
German Class B compliance statement
Hinweis zur Einhaltung der Klasse B zur elektromagnetischen Verträglichkeit
Dieses Produkt entspricht den Schutzanforderungen der EU-Richtlinie zur elektromagnetischen
Verträglichkeit Angleichung der Rechtsvorschriften über die elektromagnetische Verträglichkeit in den EU-
Mitgliedsstaaten und hält die Grenzwerte der Klasse B der Norm gemäß Richtlinie.
Um dieses sicherzustellen, sind die Geräte wie in den Handbüchern beschrieben zu installieren und zu
betreiben. Des Weiteren dürfen auch nur von der Lenovo empfohlene Kabel angeschlossen werden. Lenovo
übernimmt keine Verantwortung für die Einhaltung der Schutzanforderungen, wenn das Produkt ohne
Zustimmung der Lenovo verändert bzw. wenn Erweiterungskomponenten von Fremdherstellern ohne
Empfehlung der Lenovo gesteckt/eingebaut werden.
Zulassungsbescheinigung laut dem Deutschen Gesetz über die elektromagnetische Verträglichkeit von
Betriebsmitteln, EMVG vom 20. Juli 2007 (früher Gesetz über die elektromagnetische Verträglichkeit von
Geräten), bzw. der EU Richtlinie 2014/30/EU, der EU Richtlinie 2014/53/EU Artikel 3.1b), für Geräte der
Klasse B.
Dieses Gerät ist berechtigt, in Übereinstimmung mit dem Deutschen EMVG das EG-Konformitätszeichen -
CE - zu führen. Verantwortlich für die Konformitätserklärung nach Paragraf 5 des EMVG ist die Lenovo
(Deutschland) GmbH, Meitnerstr. 9, D-70563 Stuttgart.
Japan VCCI Class B compliance statement
Japan compliance statement for products which connect to the power
mains with rated current less than or equal to 20 A per phase
Japan notice for ac power cord
The ac power cord shipped with your product can be used only for this specific product. Do not use the ac
power cord for other devices.
Appendix D. Compliance and TCO Certified information 99
Other compliance and TCO Certified information of countries and
regions
This section provides other compliance information about Lenovo products.
Certification-related information
Product name Compliance ID Machine type(s)
• ThinkPad T14s Gen 1
• ThinkPad T14s Gen 1 LTE (for
mainland China only)
TP00105C / TP00105C0* (for
Intel models)
20T0 and 20T1
• ThinkPad X13 Gen 1
• ThinkPad X13 Gen 1 LTE (for
mainland China only)
TP00106C / TP00106C0* /
TP00106C1* / TP00106C2 * (for
Intel models)
20T2 and 20T3
• ThinkPad T14s Gen 1 TP00105D (for AMD models) 20UH and 20UJ
• ThinkPad X13 Gen 1 TP00106D (for AMD models) 20UF and 20UG
* for India only
Further compliance information related to your product is available at https://www.lenovo.com/compliance.
Regulatory labels
Depending on your country or region, you can find the government-required regulatory information through
one of the following methods:
• On a physical label attached to the outside of your computer shipping carton
• On a physical label attached to your computer
• Through an electronic-label screen (E-label screen) preinstalled on your computer
To access the E-label screen, restart the computer. When the logo screen is displayed, press F9, or tap the
prompt to enter the Startup Interrupt menu and the Regulatory Information option subsequently.
Korean E-label notice
TCO Certified
Selected models are TCO Certified and bear the TCO Certified logo.
Note: TCO Certified is an international third-party sustainability certification for IT products. For details, go
to https://www.lenovo.com/us/en/compliance/tco.
Export classification notice
This product is subject to the United States Export Administration Regulations (EAR) and has an Export
Classification Control Number (ECCN) of 5A992.c. It can be re-exported except to any of the embargoed
countries in the EAR E1 country list.
100 T14s Gen 1 and X13 Gen 1 User Guide
Lenovo product service information for Taiwan
Taiwan precautionary vision statement
警語：使用過度恐傷害視力
注意事項：
• 使用30分鐘請休息10分鐘。
• 未滿2歲幼兒不看螢幕，2歲以上每天看螢幕不要超過1小時。
Supplemental information for the Eurasian Union
Назначение
персональный компьютер для личного и служебного использования,
для передачи данных, с поддержкой различных профилей
подключения (Wi-Fi, Bluetooth и пр.).
Изготовитель
Леново ПЦ ХК Лимитед, 23/Ф Линколн Хаус, Тайку Плэйс 979 Кингз
Роуд, Куарри Бэй, Гонконг (Lenovo PC HK Limited, 23/F Lincoln House,
Taikoo Place 979 King's Road, Quarry Bay, Hong Kong)
Страна производства Китай
Наименование и местонахождение
уполномоченного изготовителем
лица
ООО «Леново (Восточная Европа/Азия)» 143401, Московская область,
г. Красногорск, бульвар Строителей, дом 4, корпус 1, помещение VII,
тел. +7 495 645 83 38, факс +7 495 645 78 77.
Импортер
Наименование, адрес импортера и информация для связи с ним
указаны на этикетке* на упаковке продукции.
*Согласно ГОСТ 2.601-2013 «Единая система конструкторской
документации. Эксплуатационные документы», пункт 5.1, подпункт
5.1.2, этикетка является видом эксплуатационных документов.
Дата изготовления (месяц и год)
Указана на этикетке* на упаковке продукции, в графе Date (дата
указана в формате год-месяц-дата). Для получения более подробной
информации посетите веб-сайт: https://support.lenovo.com
Единый знак обращения на рынке
стран Таможенного союза
Brazil audio notice
Ouvir sons com mais de 85 decibéis por longos períodos pode provocar danos ao sistema auditivo.
ENERGY STAR model information
Appendix D. Compliance and TCO Certified information 101
ENERGY STAR is a joint program of the U.S. Environmental Protection Agency and the U.S. Department of
Energy aimed at saving money and protecting the environment through energy efficient products and
practices.
Lenovo is proud to offer products with the ENERGY STAR certified designation. Lenovo computers, if carry
an ENERGY STAR mark, have been designed and tested to conform to the ENERGY STAR program
requirements for computers as prescribed by the U.S. Environmental Protection Agency. For a certified
computer, an ENERGY STAR mark may be affixed to the product, the product packaging, or displayed
electronically on the E-label screen or the power settings interface.
By using ENERGY STAR compliant products and taking advantage of the power management features of
your computer, you reduce the consumption of electricity. Reduced electrical consumption contributes to
potential financial savings, a cleaner environment, and the reduction of greenhouse gas emissions. For more
information about ENERGY STAR, go to https://www.energystar.gov.
Lenovo encourages you to make efficient use of energy an integral part of your day-to-day operations. To
help in this endeavor, Lenovo has preset a default power plan. To change the power plan, see “Set the power
plan” on page 29.
102 T14s Gen 1 and X13 Gen 1 User Guide
Appendix E. Notices and trademarks
Notices
Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult
your local Lenovo representative for information on the products and services currently available in your
area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that
Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service
that does not infringe any Lenovo intellectual property right may be used instead. However, it is the user's
responsibility to evaluate and verify the operation of any other product, program, or service.
Lenovo may have patents or pending patent programs covering subject matter described in this document.
The furnishing of this document does not give you any license to these patents. You can send license
inquiries, in writing, to:
Lenovo (United States), Inc.
8001 Development Drive
Morrisville, NC 27560
U.S.A.
Attention: Lenovo Director of Licensing
LENOVO PROVIDES THIS PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow
disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply to
you.
Changes are made periodically to the information herein; these changes will be incorporated in new editions
of the publication. To provide better service, Lenovo reserves the right to improve and/or modify the
products and software programs described in the manuals included with your computer, and the content of
the manual, at any time without additional notice.
The software interface and function and hardware configuration described in the manuals included with your
computer might not match exactly the actual configuration of the computer that you purchase. For the
configuration of the product, refer to the related contract (if any) or product packing list, or consult the
distributor for the product sales. Lenovo may use or distribute any of the information you supply in any way it
believes appropriate without incurring any obligation to you.
The products described in this document are not intended for use in implantation or other life support
applications where malfunction may result in injury or death to persons. The information contained in this
document does not affect or change Lenovo product specifications or warranties. Nothing in this document
shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo or
third parties. All information contained in this document was obtained in specific environments and is
presented as an illustration. The result obtained in other operating environments may vary.
Lenovo may use or distribute any of the information you supply in any way it believes appropriate without
incurring any obligation to you.
Any references in this publication to non-Lenovo Web sites are provided for convenience only and do not in
any manner serve as an endorsement of those Web sites. The materials at those Web sites are not part of the
materials for this Lenovo product, and use of those Web sites is at your own risk.
© Copyright Lenovo 2020, 2021 103
Any performance data contained herein was determined in a controlled environment. Therefore, the result
obtained in other operating environments may vary significantly. Some measurements may have been made
on development-level systems and there is no guarantee that these measurements will be the same on
generally available systems. Furthermore, some measurements may have been estimated through
extrapolation. Actual results may vary. Users of this document should verify the applicable data for their
specific environment.
This document is copyrighted by Lenovo and is not covered by any open source license, including any Linux
agreement(s) which may accompany software included with this product. Lenovo may update this document
at any time without notice.
For the latest information or any questions or comments, contact or visit the Lenovo Web site:
https://pcsupport.lenovo.com
Trademarks
LENOVO, LENOVO logo, THINKPAD, THINKPAD logo, TRACKPOINT, and ULTRACONNECT are trademarks
of Lenovo. Intel, Intel Optane, and Thunderbolt are trademarks of Intel Corporation or its subsidiaries in the
U.S. and/or other countries. Microsoft, Windows, Direct3D, BitLocker, and Cortana are trademarks of the
Microsoft group of companies. DisplayPort is a trademark of the Video Electronics Standards Association.
Linux is the registered trademark of Linus Torvalds in the U.S. and other countries. Ubuntu is a registered
trademark of Canonical Ltd. “Fedora” is a registered trademark of Red Hat, Inc. The terms HDMI and HDMI
High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the
United States and other countries. Wi-Fi, Wi-Fi Alliance, and Miracast are registered trademarks of Wi-Fi
Alliance. USB-C is a trademark of USB Implementers Forum. All other trademarks are the property of their
respective owners. © 2021 Lenovo.
104 T14s Gen 1 and X13 Gen 1 User Guide
