LevelOne IGP-1271 User Manual
Displayed below is the user manual for IGP-1271 by LevelOne which is a product in the Network Switches category. This manual has pages.
Related Manuals
i
IGP-1271
GUI User Guide
12-Port L3 Lite Managed Gigabit PoE Industrial Switch
Release A1
2017, Digital Data Communications GmbH, Germany. All rights reserved. All product
names are trademarks or registered trademarks of Digital Data companies
ii
About This Manual
Copyright Copyright © 2017 Digital Data Communications GmbH. All rights reserved.
The products and programs described in this User Guide are licensed products of Manufacture
Technology, This User Guide contains proprietary information protected by copyright, and this
User Guide and all accompanying hardware, software and documentation are copyrighted. No
parts of this User Guide may be copied, photocopied, reproduced, translated or reduced to any
electronic medium or machine-readable from by any means by electronic or mechanical.
Including photocopying, recording, or information storage and retrieval systems, for any purpose
other than the purchaser’s personal use, and without the prior express written permission of
Manufacture Technology.
.
Purpose This GUI user guide gives specific information on how to operate and use the management
functions of the IGP-1271 via HTTP/HTTPs web browser
Audience The Manual is intended for use by network administrators who are responsible for operating and
maintaining network equipment; consequently, it assumes a basic working knowledge of general
switch functions, the Internet Protocol (IP), and Hypertext Transfer Protocol (HTTP).
CONVENTIONS The following conventions are used throughout this manual to show information.
WARRANTY See the Customer Support/ Warranty booklet included with the product. A copy of the specific
warranty terms applicable to your Manufacture products and replacement parts can be obtained
from your Manufacture Sales and Service Office authorized dealer.
Disclaimer Manufacture Technology does not warrant that the hardware will work properly in all
environments and applications, and marks no warranty and representation, either implied or
expressed, with respect to the quality, performance, merchantability, or fitness for a particular
purpose. Manufacture disclaims liability for any inaccuracies or omissions that may have
occurred. Information in this User Guide is subject to change without notice and does not
represent a commitment on the part of Manufacture. Manufacture assumes no responsibility for
any inaccuracies that may be contained in this User Guide. Manufacture makes no commitment
to update or keep current the information in this User Guide, and reserves the righter to make
improvements to this User Guide and /or to the products described in this User Guide, at any
time without notice.
iv
Table of Contents
ABOUT THIS MANUAL .......................................................................................................................... II
Revision History ........................................................................................................................................ viii
INTRODUCTION ........................................................................................................................................... 1
CHAPTER 1 OPERATION OF WEB-BASED MANAGEMENT .......................................................... 2
CHAPTER 2 SYSTEM CONFIGURATION ............................................................................. 6
2-1 SYSTEM ........................................................................................................................................................... 6
2-1.1 Information ........................................................................................................................................ 6
2-1.2 IP ......................................................................................................................................................... 7
2-1.3 NTP ................................................................................................................................................... 10
2-1.4 Time .................................................................................................................................................. 11
2-1.5 Log .................................................................................................................................................... 14
2-1.6 Digital I/O ........................................................................................................................................ 15
2-1.7 Alarm Notification ........................................................................................................................... 15
2-2 GREEN ETHERNET ........................................................................................................................................... 19
2-2.1 Port Power Savings .......................................................................................................................... 19
2-3 PORTS CONFIGURATION ................................................................................................................................... 21
2-3.1 Ports .................................................................................................................................................. 21
2-3.2 Ports Description ............................................................................................................................. 24
2-4 DHCP .......................................................................................................................................................... 25
2-4.1 Server ................................................................................................................................................ 25
2-4.2 Snooping .......................................................................................................................................... 30
2-4.3 Relay ................................................................................................................................................. 32
2-5 SECURITY ....................................................................................................................................................... 34
2-5.1 Switch ............................................................................................................................................... 34
2-5.2 Network ............................................................................................................................................ 68
2-5.3 AAA ................................................................................................................................................. 103
2-6 AGGREGATION .............................................................................................................................................. 110
2-6.1 Static ............................................................................................................................................... 110
2-6.2 LACP ............................................................................................................................................... 112
2-7 LINK OAM .................................................................................................................................................. 114
2-7.1 Port Settings ................................................................................................................................... 114
2-7.2 Event Settings ................................................................................................................................. 116
2-8 LOOP PROTECTION .................................................................................................................................... 118
2-9 SPANNING TREE ......................................................................................................................................... 120
2-9.1 Bridge Setting ................................................................................................................................. 120
2-9.2 MSTI Mapping ................................................................................................................................ 124
2-9.3 MSTI Priorities ................................................................................................................................ 127
2-9.4 CIST Ports ....................................................................................................................................... 128
2-9.5 MSTI Ports ...................................................................................................................................... 131
2-10 IPMC PROFILE ........................................................................................................................................ 133
2-10.1 Profile Table ................................................................................................................................. 133
2-10.2 Address Entry ............................................................................................................................... 135
2-11MVR ....................................................................................................................................................... 137
2-12 IPMC ..................................................................................................................................................... 141
2-12.1 IGMP Snooping ............................................................................................................................ 141
2-12.2 MLD Snooping ............................................................................................................................. 149
2-13 LLDP ...................................................................................................................................................... 157
2-13.1 LLDP.............................................................................................................................................. 157
2-13.2 LLDP-MED .................................................................................................................................... 162
2-14 POE ........................................................................................................................................................ 171
v
2- 14.1 Configuration .............................................................................................................................. 172
2- 14.2 Power Delay ................................................................................................................................ 176
2- 14.3 Schedule Profile .......................................................................................................................... 178
2- 14.4 Auto Checking ............................................................................................................................ 179
2- 14.5 Chip Reset Schedule ................................................................................................................... 181
2-15 EPS ........................................................................................................................................................ 182
2-16 MEP....................................................................................................................................................... 185
2-17 ERPS ...................................................................................................................................................... 187
2-18 MAC TABLE ............................................................................................................................................ 189
2-19 VLAN TRANSLATION ............................................................................................................................... 193
2- 19.1 Port to Group Mapping .............................................................................................................. 193
2- 19.2 VID Translation Mapping........................................................................................................... 194
2-20 VLANS ................................................................................................................................................... 196
2-21 PRIVATE VLANS ...................................................................................................................................... 202
2-21.1 Membership ................................................................................................................................. 202
2-21.2 Port Isolation ................................................................................................................................ 204
2-22 VCL ........................................................................................................................................................ 206
2-22.1 MAC-based VLAN ........................................................................................................................ 206
2-22.2 Protocol -based VLAN ................................................................................................................. 209
2-22.3 IP Subnet-based VLAN ................................................................................................................ 214
2-23 VOICE VLAN......................................................................................................................................... 217
2-23.1 Configuration ............................................................................................................................... 217
2-23.2 OUI................................................................................................................................................ 220
2-24 ETHERNET SERVICES ................................................................................................................................. 222
2-24.1 Ports .............................................................................................................................................. 222
2-24.2 L2CP.............................................................................................................................................. 223
2-24.3 Bandwidth Profiles ...................................................................................................................... 225
2-24.4 EVCs .............................................................................................................................................. 227
2-24.5 ECEs .............................................................................................................................................. 230
2-25 QOS ....................................................................................................................................................... 234
2-25.1 Port Classification ....................................................................................................................... 235
2-25.2 Port Policing ................................................................................................................................. 238
2-25.3 Queue Policing ............................................................................................................................ 239
2-25.4 Port Scheduler.............................................................................................................................. 240
2-25.5 Port Shaping ................................................................................................................................ 244
2-25.6 Port Tag Remarking..................................................................................................................... 247
2-25.7 Port DSCP..................................................................................................................................... 250
2-25.8 DSCP-Based QoS ......................................................................................................................... 253
2-25.9 DSCP Translation ......................................................................................................................... 256
2-25.10 DSCP Classification ................................................................................................................... 259
2-25.11 QoS Control List......................................................................................................................... 261
2-25.12 Storm Control ............................................................................................................................ 267
2-26 MIRRORING ............................................................................................................................................ 269
2-27 UPNP ..................................................................................................................................................... 273
2-28 PTP ........................................................................................................................................................ 275
2-29. GVRP .................................................................................................................................................... 278
2-29.1 Global Config ............................................................................................................................... 279
2-29.2 Port Config ................................................................................................................................... 281
2-30. SFLOW ................................................................................................................................................... 282
2-31 UDLD .................................................................................................................................................... 285
2-32 RAPID RING ............................................................................................................................................ 287
2-33 SWITCH2GO ............................................................................................................................................ 288
2-33.1 Switch2go setting ........................................................................................................................ 288
2-33.2 iPush Options ............................................................................................................................... 290
vi
2-34 SMTP .................................................................................................................................................... 292
CHAPTER 3. MONITOR ...................................................................................................... 294
3-1 SYSTEM ..................................................................................................................................................... 294
3-1.1 Information .................................................................................................................................... 294
3-1.2 IP Status .......................................................................................................................................... 297
3-1.3 Log .................................................................................................................................................. 300
3-1.4 Detailed Log ................................................................................................................................... 302
3-2 GREEN ETHERNET ...................................................................................................................................... 304
3-2.1 Port Power Savings ........................................................................................................................ 304
3-3 PORTS ....................................................................................................................................................... 305
3-3.1 Traffic Overview ............................................................................................................................. 305
3-3.2 Qos Statistics .................................................................................................................................. 308
3-3.3 QCL Status ...................................................................................................................................... 310
3-3.4 Detailed Statistics .......................................................................................................................... 313
3-3.5 SFP Information ............................................................................................................................. 317
3-3.6 SFP Detail Info ............................................................................................................................... 320
3-4 LINK OAM ................................................................................................................................................ 322
3-4.1 Statistics .......................................................................................................................................... 322
3-4.2 Port Status ...................................................................................................................................... 325
3-4.3 Event Status .................................................................................................................................... 327
3-5 DHCP ...................................................................................................................................................... 330
3-5.1 Server .............................................................................................................................................. 330
3-5.2 Snooping Table .............................................................................................................................. 336
3-5.3 Relay Statistics ............................................................................................................................... 338
3-5.4 Detailed Statistics .......................................................................................................................... 341
3-6 SECURITY .................................................................................................................................................. 344
3-6.1 Access Management Statistics ...................................................................................................... 344
3-6.2 Network .......................................................................................................................................... 345
3-6.3 AAA ................................................................................................................................................. 364
3-6.4 Switch ............................................................................................................................................. 374
3-7 AGGREGATION ........................................................................................................................................... 386
3-7.1 Status .............................................................................................................................................. 386
3-7.2 LACP ............................................................................................................................................... 387
3-8 LOOP PROTECTION .................................................................................................................................... 392
3-9 SPANNING TREE ......................................................................................................................................... 394
3-9.1 Bridge Status .................................................................................................................................. 394
3-9.2 Port Status ...................................................................................................................................... 396
3-9.3 Port Statistics ................................................................................................................................. 398
3-10 MVR ...................................................................................................................................................... 400
3-10.1 Statistics ....................................................................................................................................... 400
3-10.2 MVR Channels Groups ................................................................................................................ 402
3-10.3 MVR SFM Information ................................................................................................................. 404
3-11 IPMC ..................................................................................................................................................... 407
3-11.1 IGMP Snooping ............................................................................................................................ 407
3-11.2 MLD Snooping ............................................................................................................................. 415
3-12 LLDP ...................................................................................................................................................... 423
3-12.1 Neighbour .................................................................................................................................... 423
3-12.2 LLDP-MED Neighbour ................................................................................................................. 426
3-12.3 PoE ................................................................................................................................................ 431
3-12.4 EEE ................................................................................................................................................ 434
3-12.5 Port Statistics ............................................................................................................................... 437
3-13 ETHERNET SERVICES ................................................................................................................................. 439
3-13.1 EVC Statistics ............................................................................................................................... 439
vii
3-14 PTP ........................................................................................................................................................ 441
3-15 POE ........................................................................................................................................................ 443
3-16 MAC TABLE ............................................................................................................................................ 446
3-17 VLANS ................................................................................................................................................... 449
3-17.1 Membership ................................................................................................................................. 449
3-17.2 Port ............................................................................................................................................... 452
3-18 VCL ........................................................................................................................................................ 455
3-18.1 MAC-based VLAN ........................................................................................................................ 455
3-18.2 Protocol-based VLAN .................................................................................................................. 457
3-18.3 IP Subnet-based VLAN ................................................................................................................ 462
3-19 SFLOW .................................................................................................................................................... 464
3-20 UDLD .................................................................................................................................................... 467
CHAPTER 4. DIAGNOSTICS ............................................................................................... 469
4-1 PING ......................................................................................................................................................... 469
4-2 PING6 ....................................................................................................................................................... 472
4-3 VERIPHY .................................................................................................................................................. 474
4-4 TRACEROUTE ............................................................................................................................................. 476
4-5 LINK OAM .................................................................................................................................................. 478
4-5.1 MIB Retrieval .................................................................................................................................. 478
CHAPTER 5. MAINTENANCE ............................................................................. 482
5-1 RESTART DEVICE ........................................................................................................................................ 482
5-2 REBOOT SCHEDULE .................................................................................................................................... 483
5-3 FACTORY DEFAULTS .................................................................................................................................... 485
5-4 FIRMWARE................................................................................................................................................. 486
5-4.1 Firmware upgrade ......................................................................................................................... 486
5-4.2 Firmware Selection ........................................................................................................................ 488
5-5 CONFIGURATION........................................................................................................................................ 490
5-5.1 Save startup-config ....................................................................................................................... 490
5-5.2 Download ....................................................................................................................................... 492
5-5.3 Upload ............................................................................................................................................ 494
5-5.4 Activate ........................................................................................................................................... 496
5-5.5 Delete.............................................................................................................................................. 498
5-6 SERVER REPORT ......................................................................................................................................... 499
viii
Revision History
Release
Date
Revision
Initial Release
01/06/2017
A1
Revision A1
1
INTRODUCTION
Overview
In this User Guide, it will not only tell you how to install and connect your network system but
configure and monitor the IGP-1271 through the web by (RJ-45) serial interface and Ethernet ports
step-by-step. Many explanations in detail of hardware and software functions are shown as well as the
examples of the operation for web-based interface.
The IGP-1271, the next generation Web managed switches from Manufacture, is a portfolio of
affordable managed switches that provides a reliable infrastructure for your business network. These
switches deliver more intelligent features you need to improve the availability of your critical business
applications, protect your sensitive information, and optimize your network bandwidth to deliver
information and applications more effectively. It provides the ideal combination of affordability and
capabilities for entry level networking includes small business or enterprise application and helps you
create a more efficient, better-connected workforce.
IGP-1271 Industrial L3 Lite Managed Gigabit PoE Switch provide 12 ports in a single device; the
specification is highlighted as follows.
L3 Lite features provide better manageability, security, QoS, and performance.
Support IPv4/IPv6 dual stack management
Support SSH/SSL secured management
Support SNMP v1/v2c/v3
Support RMON groups 1,2,3,9
Support sFlow
Support IGMP v1/v2/v3 Snooping
Support MLD v1/v2 Snooping
Support RADIUS and TACACS+ authentication
Support IP Source Guard
Support DHCP Relay (Option 82)
Support DHCP Snooping
Support ACL and QCL for traffic filtering
Support 802.1d(STP), 802.1w(RSTP) and 802.1s(MSTP)
Support LACP and static link aggregation
Support Q-in-Q double tag VLAN
Support GVRP dynamic VLAN
Overview of this User Guide
Chapter 1 “Operation of Web-based Management”
Chapter 2 “System Configuration”
Chapter 3 “Configuration”
Chapter 4 “Security”
Chapter 5 “Maintenance”
Revision A1
2
Chapter 1 Operation of Web-based Management
Initial
Configuration
This chapter instructs you how to configure and manage the IGP-1271 through the
web user interface. With this facility, you can easily access and monitor through any
one port of the switch all the status of the switch, including MIBs status, each port
activity, Spanning tree status, port aggregation status, multicast traffic, VLAN and
priority status, even illegal access record and so on.
The default values of the IGP-1271 are listed in the table below:
IP Address
192.168.1.1
Subnet Mask
255.255.255.0
Default Gateway
192.168.1.254
Username
admin
Password
admin
After the IGP-1271 has been finished configuration it interface, you can browse it. For
instance, type http://192.168.1.1 in the address row in a browser, it will show the
following screen and ask you inputting username and password in order to login and
access authentication.
The default username is “admin” and password is ”admin”. For the first time to use,
please enter the default username and password, and then click the <Login> button.
The login process now is completed. In this login menu, you have to input the
complete username and password respectively, the IGP-1271 will not give you a
shortcut to username automatically. This looks inconvenient, but safer.
In the IGP-1271, allowed two or more users using administrator’s identity to manage
this switch, which administrator to do the last setting, it will be an available
configuration to effect the system.
NOTE:
When you login the Switch WEB page to manage. You must first type the
Username of the admin. Password was admin., so when you type after the
end Username, please press enter. Management page to enter WEB.
When you login IGP-1271 series switch Web UI management, you can use
both ipv4 ipv6 login to manage
To optimize the display effect, we recommend you use Microsoft IE 6.0
above, Netscape V7.1 above or Firefox V1.00 above and have the resolution
1024x768. The switch supported neutral web browser interface
Revision A1
5
NOTE:
AS IGP-1271 the function enable dhcp, so If you do not have DHCP server to
provide ip addresses to the switch, the Switch default ip 192.168.1.1
Figure 1 The login page
6
Chapter 2 System Configuration
This chapter describes the entire basic configuration tasks which includes the System Information and
any manage of the Switch (e.g. Time, Account, IP, Syslog and NTP.)
2-1 System
You can identify the system by configuring the contact information, name, and location of the
switch.
2-1.1 Information
The switch system’s contact information is provided here.
Web interface
To configure System Information in the web interface:
1. Click Configuration, System, and Information.
2. Write System Contact, System Name, System Location information in this page.
3. Click Apply
Figure 2-1.1: System Information
Parameter description:
System Contact:
The textual identification of the contact person for this managed node, together with
information on how to contact this person. The allowed string length is 0 to 128, and the
allowed content is the ASCII characters from 32 to 126.
System name:
An administratively assigned name for this managed node. By convention, this is the node's
fully-qualified domain name. A domain name is a text string drawn from the alphabet
(A-Za-z), digits (0-9), minus sign (-). No space characters are permitted as part of a name.
The first character must be an alpha character. And the first or last character must not be a
minus sign. The allowed string length is 0 to 255.
System Location:
The physical location of this node(e.g., telephone closet, 3rd floor). The allowed string
length is 0 to 128, and the allowed content is the ASCII characters from 32 to 126.
Revision A1
6
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved values.
7
2-1.2 IP
The IPv4 address for the switch could be obtained via DHCP Server for VLAN 1. To manually
configure an address, you need to change the switch's default settings to values that are
compatible with your network. You may also need to establish a default gateway between the
switch and management stations that exist on another network segment.
Configure the switch-managed IP information on this page
Configure IP basic settings, control IP interfaces and IP routes.
The maximum number of interfaces supported is 8 and the maximum number of routes is 32.
Web Interface
To configure an IP address in the web interface:
1. Click Configuration, System, IP.
2. Click Add Interface then you can create new Interface on the switch.
3. Click Add Route then you can create new Route on the switch
4. Click Apply
Figure2-1.2: The IP configuration
8
Parameter description:
IP Configuration
Mode:
Configure whether the IP stack should act as a Host or a Router. In Host mode, IP traffic
between interfaces will not be routed. In Router mode traffic is routed between all
interfaces.
DNS Server
This setting controls the DNS name resolution done by the switch.
There are four servers available for configuration, and the index of the server presents the
preference (less index has higher priority) in doing DNS name resolution.
System selects the active DNS server from configuration in turn, if the preferred server does
not respond in five attempts.
The following modes are supported:
From any DHCP interfaces
The first DNS server offered from a DHCPv4 lease to a DHCPv4-enabled interface will
be used..
No DNS server
No DNS server will be used.
Configured IPv4
Explicitly provide the valid IPv4 unicast address of the DNS Server in dotted decimal
notation.
Make sure the configured DNS server could be reachable (e.g. via PING) for activating
DNS service.
From this DHCPv4 interface
Specify from which DHCPv4-enabled interface a provided DNS server should be
preferred.
Configured IPv6
Explicitly provide the valid IPv6 unicast (except linklocal) address of the DNS Server.
Make sure the configured DNS server could be reachable (e.g. via PING6) for activating
DNS service.
From this DHCPv6 interface
Specify from which DHCPv6-enabled interface a provided DNS server should be
preferred.
From any DHCPv6 interfaces
The first DNS server offered from a DHCPv6 lease to a DHCPv6-enabled interface will
be used.
DNS Proxy
When DNS proxy is enabled, system will relay DNS requests to the currently configured DNS
server, and reply as a DNS resolver to the client devices on the network.
Only IPv4 DNS proxy is now supported.
IP Interfaces
Delete
Select this option to delete an existing IP interface.
VLAN
The VLAN associated with the IP interface. Only ports in this VLAN will be able to access the IP
9
interface. This field is only available for input when creating a new interface.
IPv4 DHCP Enabled
Enable the DHCPv4 client by checking this box. If this option is enabled, the system will configure
the IPv4 address and mask of the interface using the DHCPv4 protocol. The DHCPv4 client will
announce the configured System Name as hostname to provide DNS lookup.
IPv4 DHCP Fallback Timeout
The number of seconds for trying to obtain a DHCP lease. After this period expires, a configured
IPv4 address will be used as IPv4 interface address. A value of zero disables the fallback
mechanism, such that DHCP will keep retrying until a valid lease is obtained. Legal values are 0 to
4294967295 seconds.
IPv4 DHCP Current Lease
For DHCP interfaces with an active lease, this column show the current interface address, as
provided by the DHCP server.
IPv4 Address
The IPv4 address of the interface in dotted decimal notation.
If DHCP is enabled, this field configures the fallback address. The field may be left blank if IPv4
operation on the interface is not desired - or no DHCP fallback address is desired.
IPv4 Mask
The IPv4 network mask, in number of bits (prefix length). Valid values are between 0 and 30 bits
for a IPv4 address.
If DHCP is enabled, this field configures the fallback address network mask. The field may be left
blank if IPv4 operation on the interface is not desired - or no DHCP fallback address is desired.
DHCPv6 Enable
Enable the DHCPv6 client by checking this box. If this option is enabled, the system will configure
the IPv6 address of the interface using the DHCPv6 protocol.
DHCPv6 Rapid Commit
Enable the DHCPv6 Rapid-Commit option by checking this box. If this option is enabled, the
DHCPv6 client terminates the waiting process as soon as a Reply message with a Rapid Commit
option is received.
This option is only manageable when DHCPv6 client is enabled.
DHCPv6 Current Lease
For DHCPv6 interface with an active lease, this column shows the interface address provided by
the DHCPv6 server.
IPv6 Address
The IPv6 address of the interface. A IPv6 address is in 128-bit records represented as eight fields
of up to four hexadecimal digits with a colon separating each field (:). For
example,fe80::215:c5ff:fe03:4dc7. The symbol :: is a special syntax that can be used as a shorthand
way of representing multiple 16-bit groups of contiguous zeros; but it can appear only once.
System accepts the valid IPv6 unicast address only, except IPv4-Compatible address and
IPv4-Mapped address.
The field may be left blank if IPv6 operation on the interface is not desired.
IPv6 Mask
The IPv6 network mask, in number of bits (prefix length). Valid values are between 1 and 128 bits
for a IPv6 address.
The field may be left blank if IPv6 operation on the interface is not desired.
Resolving IPv6 DAD
The link-local address is formed from an interface identifier based on the hardware address which
10
is supposed to be uniquely assigned. Once the DAD (Duplicate Address Detection) detects the
address duplication, the operation on the interface SHOULD be disabled.
At this moment, manual intervention is required to resolve the address duplication. For example,
check whether the loop occurs in the VLAN or there is indeed other device occupying the same
hardware address as the device in the VLAN.
After making sure the specific link-local address is unique on the IPv6 link in use, delete and then
add the specific IPv6 interface to restart the IPv6 operations on this interface.
IP Routes
Delete
Select this option to delete an existing IP route.
Network
The destination IP network or host address of this route. Valid format is dotted decimal
notationor a valid IPv6 notation. A default route can use the value 0.0.0.0or IPv6 :: notation.
Mask Length
The destination IP network or host mask, in number of bits (prefix length). It defines how
much of a network address that must match, in order to qualify for this route. Valid values
are between 0 and 32 bits respectively 128 for IPv6 routes. Only a default route will have a
mask length of 0 (as it will match anything).
Gateway
The IP address of the IP gateway. Valid format is dotted decimal notationor a valid IPv6
notation. Gateway and Network must be of the same type.
Next Hop VLAN (Only for IPv6)
The VLAN ID (VID) of the specific IPv6 interface associated with the gateway.
The given VID ranges from 1 to 4095 and will be effective only when the corresponding IPv6
interface is valid.
If the IPv6 gateway address is link-local, it must specify the next hop VLAN for the gateway.
If the IPv6 gateway address is not link-local, system ignores the next hop VLAN for the
gateway.
Buttons
Add Interface:
Click to add a new IP interface. A maximum of 8 interfaces is supported.
Add Route:
Click to add a new IP route. A maximum of 32 routes is supported.
Apply:
Click to save changes.
Reset:
Click to undo any changes made locally and revert to previously saved values.
2-1.3 NTP
NTP is Network Time Protocol and is used to sync the network time based Greenwich Mean
Time (GMT). If use the NTP mode and select a built-in NTP time server or manually specify an
user-defined NTP server as well as Time Zone, the switch will sync the time in a short after
pressing <Apply> button. Though it synchronizes the time automatically, NTP does not update
the time periodically without user’s processing.
11
Time Zone is an offset time off GMT. You have to select the time zone first and then perform
time sync via NTP because the switch will combine this time zone offset and updated NTP time
to come out the local time, otherwise, you will not able to get the correct time. The switch
supports configurable time zone from –12 to +13 step 1 hour.
Default Time zone: +8 Hrs.
Web Interface
To configure NTP in the web interface:
1. Click Configuration, System, NTP.
2. Specify the Time parameter in manual parameters.
3. Click Apply.
Figure 2-1.3: The NTP configuration
Parameter description:
Mode :
Indicates the NTP mode operation. Possible modes are:
Enabled: Enable NTP client mode operation.
Disabled: Disable NTP client mode operation.
Server 1 to 5 :
Provide the IPv4 or IPv6 address of a NTP server. IPv6 address is in 128-bit records
represented as eight fields of up to four hexadecimal digits with a colon separating each
field (:). For example, 'fe80::215:c5ff:fe03:4dc7'. The symbol '::' is a special syntax that can be
used as a shorthand way of representing multiple 16-bit groups of contiguous zeros; but it
can appear only once. It can also represent a legally valid IPv4 address. For example,
'::192.1.2.34'. In addition, it can also accept a domain name address.
Buttons
Apply – Click to save changes.
Reset - Click to undo any changes made locally and revert to previously saved values.
Revision A1
11
2-1.4 Time
The switch provides manual and automatic ways to set the system time via NTP. Manual
setting is simple and you just input “Year”, “Month”, “Day”, “Hour” and “Minute” within the
valid value range indicated in each item.
Web Interface
To configure Time in the web interface:
1. Click Configuration, System and Time
2. Specify the Time parameter.
3. Click Apply.
Figure 2-1.4: The time configuration
12
Parameter description:
Time Configuration
Clock Source:
There are two modes for configuring how the Clock Source from. Select "Use Local
Settings" : Clock Source from Local Time. Select "Use NTP Server" : Clock Source from NTP
Server.
System Date:
Show the current time of the system. The year of system date limits between 2011 and 2037.
Time Zone Configuration
Time Zone:
Lists various Time Zones worldwide. Select appropriate Time Zone from the drop down and
click Apply to set.
Acronym:
User can set the acronym of the time zone. This is a User configurable acronym to identify
the time zone. (Range: Up to 16 characters)
Daylight Saving Time Configuration
Daylight Saving Time:
This is used to set the clock forward or backward according to the configurations set below
for a defined Daylight Saving Time duration. Select 'Disable' to disable the Daylight Saving
Time configuration. Select 'Recurring' and configure the Daylight Saving Time duration to
repeat the configuration every year. Select 'Non-Recurring' and configure the Daylight
13
Saving Time duration for single time configuration. (Default: Disabled).
Recurring Configuration
Start time settings:
Week - Select the starting week number.
Day - Select the starting day.
Month - Select the starting month.
Hours - Select the starting hour.
Minutes - Select the starting minute.
End time settings:
Week - Select the ending week number.
Day - Select the ending day.
Month - Select the ending month.
Hours - Select the ending hour.
Minutes - Select the ending minute.
Offset settings:
Offset - Enter the number of minutes to add during Daylight Saving Time. (Range: 1 to 1440)
NOTE: The under “Start Time Settings” and “End Time Settings” was
displayed what you set on the “Start Time Settings” and “End Time
Settings” field information.
Buttons
Apply – Click to save changes.
Reset - Click to undo any changes made locally and revert to previously saved values.
14
2-1.5 Log
The log is a standard for logging program messages . It allows separation of the software that
generates messages from the system that stores them and the software that reports and
analyzes them. It can be used as well a generalized informational, analysis and debugging
messages. It is supported by a wide variety of devices and receivers across multiple platforms.
Web Interface
To configure log configuration in the web interface:
1. Click Configuration, System and log.
2. Specify the syslog parameters include IP Address of Syslog server and Port number.
3. Evoke the Syslog to enable it.
4. Click Apply.
Figure2-1.5: The System Log configuration
Parameter description:
Server Mode :
Indicate the server mode operation. When the mode operation is enabled, the syslog
message will send out to syslog server. The syslog protocol is based on UDP communication
and received on UDP port 514 and the syslog server will not send acknowledgments back
sender since UDP is a connectionless protocol and it does not provide acknowledgments.
The syslog packet will always send out even if the syslog server does not exist. Possible
modes are:
Enabled: Enable server mode operation.
Disabled: Disable server mode operation.
Server Address :
Indicates the IPv4 hosts address of syslog server. If the switch provide DNS feature, it also
can be a host name.
Buttons
Apply – Click to save changes.
Reset - Click to undo any changes made locally and revert to previously saved values.
15
2-1.6 Digital I/O
Configure the normal modes of digital input/output (DI/DO).
Web Interface
To configure Digital I/O configuration in the web interface:
1. Click Configuration, System and Digital I/O.
2. Specify the Digital I/O Normal Mode..
3. Click Apply.
Figure2-1.6: The Digital I/O Configuration
Parameter description:
DI Normal Mode
Set the normal mode of the digital input(DI). You can set it to High or Low.
DO Normal Mode
Set the normal mode of the digital output(DO). You can set it to Open or Close.
Buttons
Apply – Click to save changes.
2-1.7 Alarm Notification
2-1.7.1 Trap Event Severity
This page displays current trap event severity configurations. Trap event
severity can also be configured here.
Web Interface
To configure Trap Event Severity in the web interface:
1. Click Configuration, System, Alarm Notification and Trap Event Severity.
2. Specify the Group Name, Severity Level, Syslog, Trap, SMIP, Switch2go and Digital out.
3. Click Apply.
Figure 2-1.7.1: The Trap Event Severity
16
Parameter description:
Group Name
The name identifying the severity group.
Severity Level
Every group has an severity level. The following level types are supported:
<0> Emergency: System is unusable.
<1> Alert: Action must be taken immediately.
<2> Critical: Critical conditions.
<3> Error: Error conditions.
<4> Warning: Warning conditions.
<5> Notice: Normal but significant conditions.
<6> Information: Information messages.
<7> Debug: Debug-level messages.
Syslog
Enable - Select this Group Name in Syslog.
Trap
Enable - Select this Group Name in Trap.
SMTP
Enable - Select this Group Name in SMTP.
Switch2go
Enable - Select this Group Name in Push Notification.
Digital out
Enable - Select this Group Name in Digital Out.
Buttons
Apply – Click to save changes.
Reset - Click to undo any changes made locally and revert to previously saved values.
2-1.7.2 Port Event Setting
This page is for configuring the port events.
Web Interface
17
To configure Trap Event Severity in the web interface:
1. Click Configuration, System, Alarm Notification and Port Event Setting.
2. Specify the Traffic and Action.
3. Click Apply.
Figure 2-7.1.2: The Port Event Setting
Parameter description:
Active
To active the event handler of this port.
Port
This is the logical port number for this row.
Link On
Event is triggered when link on.
Link Off
Event is triggered when link off.
Traffic Overload
Event is triggered when the traffic is overload.
Traffic Rx-Threshold
Event is triggered when Rx reach this threshold.
Traffic Duration
Event is triggered when the traffic duration reach this value.
Action Syslog
Enable this port for Syslog.
Action Trap
Enable this port for Trap.
Action SMTP
Enable this port for SMTP.
Action Switch2go
Enable this port for Switch2go iPush.
Action Digital Out
18
Enable this port for Digital Out.
Severity
Every port has a severity level. The following level types are supported:
<0> Emergency: System is unusable.
<1> Alert: Action must be taken immediately.
<2> Critical: Critical conditions.
<3> Error: Error conditions.
<4> Warning: Warning conditions.
<5> Notice: Normal but significant conditions.
<6> Information: Information messages.
<7> Debug: Debug-level messages.
Buttons
Apply – Click to save changes.
Reset - Click to undo any changes made locally and revert to previously saved values.
19
2-2 Green Ethernet
2-2.1 Port Power Savings
This page allows the user to configure the port power savings features.
EEE is a power saving option that reduces the power usage when there is low or no traffic
utilization.
EEE works by powering down circuits when there is no traffic. When a port gets data to be
transmitted all circuits are powered up. The time it takes to power up the circuits is named
wakeup time. The default wakeup time is 17 us for 1Gbit links and 30 us for other link speeds.
EEE devices must agree upon the value of the wakeup time in order to make sure that both the
receiving and transmitting device has all circuits powered up when traffic is transmitted. The
devices can exchange wakeup time information using the LLDP protocol.
EEE works for ports in auto-negotiation mode, where the port is negotiated to either 1G or 100
Mbit full duplex mode.
For ports that are not EEE-capable the corresponding EEE checkboxes are grayed out and thus
impossible to enable EEE for.
When a port is powered down for saving power, outgoing traffic is stored in a buffer until the
port is powered up again. Because there are some overhead in turning the port down and up,
more power can be saved if the traffic can be buffered up until a large burst of traffic can be
transmitted. Buffering traffic will give some latency in the traffic.
Web Interface
To configure a Port Power Saving Configuration in the web interface:
1. Click Configuration, Green Ethernet and Port Power Savings
2. Evoke to enable or disable the ActiPHY, PerfectReach, EEE and EEE Urgent Queues.
3. Click Apply.
Figure 2-2.1: The Port Power Saving Configuration
Parameter description:
20
Optimize EEE for
The switch can be set to optimize EEE for either best power saving or least traffic latency.
Port:
The switch port number of the logical port.
ActiPHY :
Link down power savings enabled.
ActiPHY works by lowering the power for a port when there is no link. The port is power up
for short moment in order to determine if cable is inserted.
PerfectReach :
Cable length power savings enabled.
PerfectReach works by determining the cable length and lowering the power for ports with
short cables.
EEE :
Controls whether EEE is enabled for this switch port.
For maximizing power savings, the circuit isn't started at once transmit data is ready for a
port, but is instead queued until a burst of data is ready to be transmitted. This will give
some traffic latency.
If desired it is possible to minimize the latency for specific frames, by mapping the frames to
a specific queue (done with QOS), and then mark the queue as an urgent queue. When an
urgent queue gets data to be transmitted, the circuits will be powered up at once and the
latency will be reduced to the wakeup time.
EEE Urgent Queues
Queues set will activate transmission of frames as soon as data is available. Otherwise the
Squeue will postpone transmission until a burst of frames can be transmitted.
Buttons
Apply – Click to save changes.
Reset - Click to undo any changes made locally and revert to previously saved values.
21
2-3 Ports Configuration
2-3.1 Ports
This page displays current port configurations. Ports can also be configured here.
Web Interface
To configure a Current Port Configuration in the web interface:
1. Click Configuration, Ports Configuration, and Ports
2. Specify the Speed Configured, Flow Control, Maximum Frame size, Excessive
Collision mode and Power Control.
3. Click Apply.
Figure 2-3.1: The Port Configuration
Parameter description:
22
Port :
This is the logical port number for this row.
Link :
The current link state is displayed graphically. Green indicates the link is up and red
that it is down.
Current Link Speed :
Provides the current link speed of the port.
Configured Link Speed :
Selects any available link speed for the given switch port. Only speeds supported by
the specific port is shown. Possible speeds are:
Disabled - Disables the switch port operation.
Auto - Port auto negotiating speed with the link partner and selects the highest
speed that is compatible with the link partner.
10Mbps HDX - Forces the cu port in 10Mbps half-duplex mode.
10Mbps FDX - Forces the cu port in 10Mbps full duplex mode.
100Mbps HDX - Forces the cu port in 100Mbps half-duplex mode.
100Mbps FDX - Forces the cu port in 100Mbps full duplex mode.
1Gbps FDX - Forces the port in 1Gbps full duplex
2.5Gbps FDX - Forces the Serdes port in 2.5Gbps full duplex mode.
SFP_Auto_AMS - Automatically determines the speed of the SFP. Note: There is no
standardized way to do SFP auto detect, so here it is done by reading the SFP rom.
Due to the missing standardized way of doing SFP auto detect some SFPs might not
be detectable. The port is set in AMS mode. Cu port is set in Auto mode.
100-FX - SFP port in 100-FX speed. Cu port disabled.
1000-X - SFP port in 1000-X speed. Cu port disabled.
Ports in AMS mode with 1000-X speed has Cu port preferred.
Ports in AMS mode with 1000-X speed has fiber port preferred.
Ports in AMS mode with 100-FX speed has fiber port preferred.
23
Advertise Duplex
When duplex is set as auto i.e auto negotiation, the port will only advertise the
specified duplex as either Fdx or Hdx to the link partner. By default port will
advertise all the supported duplexes if the Duplex is Auto.
Advertise Speed
When Speed is set as auto i.e auto negotiation, the port will only advertise the
specified speeds (10M100M 1G) to the link partner. By default port will advertise all
the supported speeds if speed is set as Auto.
Flow Control :
When Auto Speed is selected on a port, this section indicates the flow control capability
that is advertised to the link partner.
When a fixed-speed setting is selected, that is what is used. The Current Rx column
indicates whether pause frames on the port are obeyed, and the Current Tx column
indicates whether pause frames on the port are transmitted. The Rx and Tx settings are
determined by the result of the last Auto Negotiation.
Check the configured column to use flow control. This setting is related to the setting for
Configured Link Speed.
NOTICE: The 100FX standard doesn't support Auto Negotiation, so when in 100FX mode
the flow control capabilities will always be shown as "disabled".Maximum Frame Size :
Enter the maximum frame size allowed for the switch port, including FCS.
PFC
When PFC (802.1Qbb Priority Flow Control) is enabled on a port then flow control
on a priority level is enabled. Through the Priority field, range (one or more) of
priorities can be configured, e.g. '0-3,7' which equals '0,1,2,3,7'. PFC is not
supported through auto negotiation. PFC and Flowcontrol cannot both be enabled
on the same port.
Maximum Frame Size
Enter the maximum frame size allowed for the switch port, including FCS. The
rangeis 1518-9600 bytes.
Excessive Collision Mode :
Configure port transmit collision behavior.
24
Discard: Discard frame after 16 collisions (default).
Restart: Restart backoff algorithm after 16 collisions.
Frame Length Check
Configures if frames with incorrect frame length in the EtherType/Length field shall
be dropped. An Ethernet frame contains a field EtherType which can be used to
indicate the frame payload size (in bytes) for values of 1535 and below. If the
EtherType/Length field is above 1535, it indicates that the field is used as an
EtherType (indicating which protocol is encapsulated in the payload of the frame). If
"frame length check" is enabled, frames with payload size less than 1536 bytes are
dropped, if the EtherType/Length field doesn't match the actually payload length. If
"frame length check" is disabled, frames are not dropped due to frame length
mismatch. Note: No drop counters count frames dropped due to frame length
mismatch
Buttons
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
Upper left icon (Refresh)
You can click them for refresh the Port link Status by manual
2-3.2 Ports Description
This page displays current port description.
Web Interface
To configure a Port Description in the web interface:
1. Click Configuration, Port, then Port Description
2. Specify the detail Port alias or description an alphanumeric string describing the
full name and version identification for the system’s hardware type, software
version, and networking application.
3. Click Apply.
Figure 2-3.2: The Port Configuration
25
Parameter description:
Port :
This is the logical port number for this row.
Description :
Enter up to 47 characters to be descriptive name for identifies this port.
Buttons
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
2-4 DHCP
The section describes to configure the DHCP Snooping parameters of the switch. The
DHCP Snooping can prevent attackers from adding their own DHCP servers to the
network.
2-4.1 Server
2-4.1.1 Mode
This page configures global mode and VLAN mode to enable/disable
DHCP server per system and per VLAN.
26
Web Interface
To configure DHCP server mode in the web interface:
4. Click Configuration, DHCP, Server, Mode
5. Select “Enabled” in the Global Mode of DHCP Server Mode Configuration.
6. Add Vlan range.
7. Click Apply.
Figure 2-4.1.1: The DHCP server Mode
Parameter description:
Mode :
27
Configure the operation mode per system. Possible modes are:
Enable: Enable DHCP server per system.
Disable: Disable DHCP server pre system.
VLAN Range :
Indicate the VLAN range in which DHCP server is enabled or disabled. The first VLAN ID must
be smaller than or equal to the second VLAN ID. BUT, if the VLAN range contains only 1
VLAN ID, then you can just input it into either one of the first and second VLAN ID or both.
On the other hand, if you want to disable existed VLAN range, then you can follow the steps.
1. press “ADD VLAN Range” to add a new VLAN range.
2. Input the VLAN range that you want to disable.
3. Choose Mode to be disabled.
4. Press “Apply” to apply the change.
Then, you will see the disabled VLAN range is removed from the DHCP Server mode
configuration page.
Mode :
Indicate the operation mode per VLAN. Possible modes are:
Enable: Enable DHCP server per VLAN.
Disable: Disable DHCP server pre VLAN.
Buttons
Add VLAN Range - Click to add a new VLAN range.
Apply – Click to save changes.
Reset - Click to undo any changes made locally and revert to previously saved
values.
2-4.1.2 Excluded IP
This page configures excluded IP addresses. DHCP server will not
allocate these excluded IP addresses to DHCP client.
Web Interface
28
To configure DHCP server excluded IP in the web interface:
1. Click Configuration, DHCP, Server, Excluded IP
2. Click Add IP Range then you can create new IP Range on the switch.
3. Click Apply.
Figure 2-4.1.2: The DHCP server excluded IP
Parameter description:
IP Range :
Define the IP range to be excluded IP addresses. The first excluded IP must be smaller than or
equal to the second excluded IP. BUT, if the IP range contains only 1 excluded IP, then you can
just input it to either one of the first and second excluded IP or both.
Buttons
Add IP Range - Click to add a new excluded IP range.
Apply – Click to save changes.
Reset - Click to undo any changes made locally and revert to previously saved
values.
29
2-4.1.3 Pool
This page manages DHCP pools. According to the DHCP pool, DHCP
server will allocate IP address and deliver configuration parameters to
DHCP client.
Web Interface
To configure DHCP server pool in the web interface:
1. Click Configuration, DHCP, Server, Pool
2. Click Add New Pool then you can create new Pool on the switch.
3. Click Apply.
Figure 2-4.1.3: The DHCP server pool
Parameter description:
Pool Setting
Add or delete pools.
30
Adding a pool and giving a name is to create a new pool with "default"
configuration. If you want to configure all settings including type, IP subnet mask
and lease time, you can click the pool name to go into the configuration page.
Name :
Configure the pool name that accepts all printable characters, except white space. If you want
to configure the detail settings, you can click the pool name to go into the configuration
page.
Type :
Display which type of the pool is.
Network: the pool defines a pool of IP addresses to service more than one DHCP client.
Host: the pool services for a specific DHCP client identified by client identifier or hardware
address.
If "-" is displayed, it means not defined.
IP :
Display network number of the DHCP address pool.
If "-" is displayed, it means not defined.
Subnet Mask :
Display subnet mask of the DHCP address pool.
If "-" is displayed, it means not defined.
Lease Time :
Display lease time of the pool.
Buttons
Add New Pool - Click to add a new DHCP pool.
Apply – Click to save changes.
Reset - Click to undo any changes made locally and revert to previously saved
values.
2-4.2 Snooping
31
DHCP Snooping is used to block intruder on the untrusted ports of the
switch device when it tries to intervene by injecting a bogus DHCP reply
packet to a legitimate conversation between the DHCP client and server.
The section describes to configure the DHCP Snooping parameters of
the switch. The DHCP Snooping can prevent attackers from adding their
own DHCP servers to the network.
Web Interface
To configure DHCP snooping in the web interface:
1. Click Configuration, DHCP, Snooping
2. Select “Enabled” in the Mode of DHCP Snooping Configuration.
3. Select “Trusted” of the specific port in the Mode of Port Mode Configuration.
4. Click Apply.
Figure 2-4.2: The DHCP Snooping Configuration
Parameter description:
Snooping Mode :
Indicates the DHCP snooping mode operation. Possible modes are:
Enabled: Enable DHCP snooping mode operation. When DHCP snooping mode
operation is enabled, the DHCP request messages will be forwarded to trusted
ports and only allow reply packets from trusted ports.
32
Disabled: Disable DHCP snooping mode operation.
Port Mode Configuration
Indicates the DHCP snooping port mode. Possible port modes are:
Trusted: Configures the port as trusted source of the DHCP messages.
Untrusted: Configures the port as untrusted source of the DHCP messages.
Buttons
Apply – Click to save changes.
Reset - Click to undo any changes made locally and revert to previously saved
values.
2-4.3 Relay
A DHCP relay agent is used to forward and to transfer DHCP messages
between the clients and the server when they are not in the same
subnet domain. It stores the incoming interface IP address in the
GIADDR field of the DHCP packet. The DHCP server can use the value of
GIADDR field to determine the assigned subnet. For such condition,
please make sure the switch configuration of VLAN interface IP address
and PVID(Port VLAN ID) correctly.
Web Interface
To configure DHCP Relay in the web interface:
1. Click Configuration, DHCP, Relay
2. Specify the Relay Mode, Relay server, Relay Information Mode, Relay Information
police.
3. Click Apply.
Figure 2-4.3: The DHCP Relay Configuration
33
Parameter description:
Relay Mode :
Indicates the DHCP relay mode operation.
Possible modes are:
Enabled: Enable DHCP relay mode operation. When DHCP relay mode operation is
enabled, the agent forwards and transfers DHCP messages between the clients and
the server when they are not in the same subnet domain. And the DHCP broadcast
message won't be flooded for security considerations.
Disabled: Disable DHCP relay mode operation.
Relay Server
Indicates the DHCP relay server IP address.
Relay Information Mode
Indicates the DHCP relay information mode option operation. The option 82 circuit
ID format as "[vlan_id][module_id][port_no]". The first four characters represent the
VLAN ID, the fifth and sixth characters are the module ID(in standalone device it
always equal 0, in stackable device it means switch ID), and the last two characters
are the port number. For example, "00030108" means the DHCP message receive
form VLAN ID 3, switch ID 1, port No 8. And the option 82 remote ID value is equal
the switch MAC address.
Possible modes are:
Enabled: Enable DHCP relay information mode operation. When DHCP relay
information mode operation is enabled, the agent inserts specific information
(option 82) into a DHCP message when forwarding to DHCP server and removes it
34
from a DHCP message when transferring to DHCP client. It only works when DHCP
relay operation mode is enabled.
Disabled: Disable DHCP relay information mode operation.
Relay Information Policy :
Indicates the DHCP relay information option policy. When DHCP relay information
mode operation is enabled, if the agent receives a DHCP message that already
contains relay agent information it will enforce the policy. The 'Replace' policy is
invalid when relay information mode is disabled. Possible policies are:
Replace: Replace the original relay information when a DHCP message that already
contains it is received.
Keep: Keep the original relay information when a DHCP message that already
contains it is received.
Drop: Drop the package when a DHCP message that already contains relay
information is received.
Buttons
Apply – Click to save changes.
Reset - Click to undo any changes made locally and revert to previously saved
values.
2-5 Security
This section shows you to configure the Port Security settings of the Switch. You can
use the Port Security feature to restrict input to an interface by limiting and identifying
MAC addresses.
2-5.1 Switch
2-5.1.1 Users
This page provides an overview of the current users. Currently the only way to login as
another user on the web server is to close and reopen the browser
35
Web Interface
To configure User in the web interface:
1. Click Configuration, Security, Switch, Users.
2. Click Add new user
3. Specify the User Name parameter.
4. Click Apply.
Figure 2-5.1.1: The Users configuration
Parameter description:
User Name
The name identifying the user. This is also a link to Add/Edit User.Password
The password of the user. The allowed string length is 0 to 31. Any printable
characters including space is accepted.
Privilege Level
The privilege level of the user. The allowed range is 0 to 15. If the privilege level value is
15, it can access all groups, i.e. that is granted the fully control of the device. But others
value need to refer to each group privilege level. User's privilege should be same or
greater than the group privilege level to have the access of that group. By default setting,
most groups privilege level 5 has the read-only access and privilege level 10 has the
read-write access. And the system maintenance (software upload, factory defaults and
etc.) need user privilege level 15. Generally, the privilege level 15 can be used for an
administrator account, privilege level 10 for a standard user account and privilege level 5
for a guest account.
36
Buttons
Add New User: Click to add a new user.
2-5.1.2 Privilege Level
This page provides an overview of the privilege levels.
Web Interface
To configure Privilege Level in the web interface:
1. Click SYSTEM, Account, Privilege Level.
2. Specify the Privilege parameter.
3. Click Apply.
Figure2-5.1.2: The Privilege Level configuration
Parameter description:
Group Name
37
The name identifying the privilege group. In most cases, a privilege level group
consists of a single module (e.g. LACP, RSTP or QoS), but a few of them contains
more than one. The following description defines these privilege level groups in
details:
System: Contact, Name, Location, Timezone, Daylight Saving Time, Log.
Security: Authentication, System Access Management, Port (contains Dot1x port,
MAC based and the MAC Address Limit), ACL, HTTPS, SSH, ARP Inspection, IP
source guard.
IP: Everything except 'ping'.
Port: Everything except 'VeriPHY'.
Diagnostics: 'ping' and 'VeriPHY'.
Maintenance: CLI- System Reboot, System Restore Default, System Password,
Configuration Save, Configuration Load and Firmware Load. Web- Users, Privilege
Levels and everything in Maintenance.
Debug: Only present in CLI.
Privilege Levels
Every group has an authorization Privilege level for the following sub groups:
configuration read-only, configuration/execute read-write, status/statistics
read-only, and status/statistics read-write (e.g. for clearing of statistics). User
Privilege should be same or greater than the authorization Privilege level to have
the access to that group.
Buttons
Apply – Click to save changes.
Reset - Click to undo any changes made locally and revert to previously saved
values.
2-5.1.3 Authentication Method
This page shows how to configure a user with authenticated when he logs into the
switch via one of the management client interfaces.
38
Web Interface
To configure a Authentication Method Configuration in the web interface:
1. Specify the Client (console, telent, ssh, web) which you want to monitor.
2. Specify the Authentication Method (none,local, radius, tacacs+)
3. Checked Fallback.
4. Click Apply.
Figure 2-5.1.3: The Authentication Method Configuration
Parameter description:
Client :
The management client for which the configuration below applies.
Authentication Method :
39
Authentication Method can be set to one of the following values:
none : authentication is disabled and login is not possible.
local : use the local user database on the switch for authentication.
radius : use a remote RADIUS server for authentication.
tacacs+ : use a remote TACACS+ server for authentication.
Methods that involves remote servers are timed out if the remote servers are offline.
In this case the next method is tried. Each method is tried from left to right and
continues until a method either approves or rejects a user. If a remote server is used
for primary authentication it is recommended to configure secondary
authentication as 'local'. This will enable the management client to login via the
local user database if none of the configured authentication servers are alive.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
2-5.1.4 SSH
This section shows you to use SSH (Secure SHell) to securely access the Switch. SSH is
a secure communication protocol that combines authentication and data encryption
to provide secure encrypted communication.
Web Interface
To configure a SSH Configuration in the web interface:
1. Select “Enabled” in the Mode of SSH Configuration.
2. Click Apply.
Figure 2-5.1.4: The SSH Configuration
40
Parameter description:
Mode :
Indicates the SSH mode operation. Possible modes are:
Enabled: Enable SSH mode operation.
Disabled: Disable SSH mode operation.
Buttons:
Apply – Click to save changes.
Reset - Click to undo any changes made locally and revert to previously saved
values.
41
2-5.1.5 HTTPs
This section shows you how to use HTTPS to securely access the Switch. HTTPS is a
secure communication protocol that combines authentication and data encryption to
provide secure encrypted communication via the browser.
Web Interface
To configure a HTTPS Configuration in the web interface:
1. Select “Enabled” in the Mode of HTTPS Configuration.
2. Select “Enabled” in the Automatic Redirect of HTTPS Configuration.
3. Click Apply.
Figure 2-5.1.5: The HTTPS Configuration
Parameter description:
Mode :
Indicates the HTTPS mode operation. Possible modes are:
Enabled: Enable HTTPS mode operation.
Disabled: Disable HTTPS mode operation.
Automatic Redirect :
Indicates the HTTPS redirect mode operation. Automatically redirect web browser
to HTTPS when HTTPS mode is enabled. Possible modes are:
Enabled: Enable HTTPS redirect mode operation.
Disabled: Disable HTTPS redirect mode operation.
42
43
2-5.1.6 Access Management
This section shows you to configure access management table of the Switch including
HTTP/HTTPS, SNMP, and TELNET/SSH. You can manage the Switch over an Ethernet
LAN, or over the Internet.
Web Interface
To configure an Access Management Configuration in the web interface:
1. Select “Enabled” in the Mode of Access Management Configuration.
2. Click “Add new entry”.
3. Specify the Start IP Address, End IP Address.
4. Checked Access Management method (HTTP/HTTPS, SNMP, and TELNET/SSH) in
the entry.
5. Click Apply.
Figure 2-5.1.6: The Access Management Configuration
Parameter description:
44
Mode :
Indicates the access management mode operation. Possible modes are:
Enabled: Enable access management mode operation.
Disabled: Disable access management mode operation.
VLAN ID :
Indicates the VLAN ID for the access management entry.
Delete :
Check to delete the entry. It will be deleted during the next save.
Start IP address :
Indicates the start IP address for the access management entry.
End IP address :
Indicates the end IP address for the access management entry.
HTTP/HTTPS :
Indicates that the host can access the switch from HTTP/HTTPS interface if the host
IP address matches the IP address range provided in the entry.
SNMP :
Indicates that the host can access the switch from SNMP interface if the host IP
address matches the IP address range provided in the entry.
TELNET/SSH :
Indicates that the host can access the switch from TELNET/SSH interface if the host
IP address matches the IP address range provided in the entry.
Buttons:
Add New Entry – Click to add a new access management entry.
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
45
2-5.1.7 SNMP
Any Network Management System (NMS) running the Simple Network Management
Protocol (SNMP) can manage the Managed devices equipped with SNMP agent,
provided that the Management Information Base (MIB) is installed correctly on the
managed devices. The SNMP is a protocol that is used to govern the transfer of
information between SNMP manager and agent and traverses the Object Identity (OID)
of the management Information Base (MIB), described in the form of SMI syntax.
SNMP agent is running on the switch to response the request issued by SNMP
manager.
Basically, it is passive except issuing the trap information. The switch supports a switch
to turn on or off the SNMP agent. If you set the field SNMP “Enable”, SNMP agent will
be started up. All supported MIB OIDs, including RMON MIB, can be accessed via
SNMP manager. If the field SNMP is set “Disable”, SNMP agent will be de-activated,
the related Community Name, Trap Host IP Address, Trap and all MIB counters will be
ignored.
2-5.1.7.1 System
This section describes how to configure SNMP System on the switch. This function is
used to configure SNMP settings, community name, trap host and public traps as well
as the throttle of SNMP. A SNMP manager must pass the authentication by
identifying both community names, then it can access the MIB information of the
target device. So, both parties must have the same community name. Once
completing the setting, click <Apply> button, the setting takes effect.
Web Interface
To display the configure SNMP System in the web interface:
1. Click SNMP, System.
2. Evoke SNMP State to enable or disable the SNMP function.
3. Specify the Engine ID
4. Click Apply.
Figure2-5.1.7.1: The SNMP System Configuration
46
Parameter description:
Mode :
Indicates the SNMP mode operation. Possible modes are:
Enabled: Enable SNMP mode operation.
Disabled: Disable SNMP mode operation.
Version
Indicates the SNMP supported version. Possible versions are:
SNMP v1: Set SNMP supported version 1.
SNMP v2c: Set SNMP supported version 2c.
SNMP v3: Set SNMP supported version 3.
Read Community
Indicates the community read access string to permit access to SNMP agent. The
allowed string length is 0 to 255, and the allowed content is the ASCII characters
from 33 to 126.
The field is applicable only when SNMP version is SNMPv1 or SNMPv2c. If SNMP
version is SNMPv3, the community string will be associated with SNMPv3
communities table. It provides more flexibility to configure security name than a
SNMPv1 or SNMPv2c community string. In addition to community string, a
particular range of source addresses can be used to restrict source subnet.
Write Community
47
Indicates the community write access string to permit access to SNMP agent. The
allowed string length is 0 to 255, and the allowed content is the ASCII characters
from 33 to 126.
The field is applicable only when SNMP version is SNMPv1 or SNMPv2c. If SNMP
version is SNMPv3, the community string will be associated with SNMPv3
communities table. It provides more flexibility to configure security name than a
SNMPv1 or SNMPv2c community string. In addition to community string, a
particular range of source addresses can be used to restrict source subnet.
Engine ID
Indicates the SNMPv3 engine ID. The string must contain an even number(in
hexadecimal format) with number of digits between 10 and 64, but all-zeros and
all-'F's are not allowed. Change of the Engine ID will clear all original local users.
2-5.1.7.2 Trap
Configure SNMP trap on this page.
Global Settings
Configure SNMP trap on this page.
Web Interface
To display the configure SNMP Trap Configuration in the web interface:
1. Click Configuration, Switch, SNMP, Trap.
2. Click Add New Entry then you can create new SNMP Trap on the switch.
3. Click Apply
Figure2-5.1.7.2: The SNMP Trap Configuration
48
Trap Mode
Indicates the trap mode operation. Possible modes are:
Enabled: Enable SNMP trap mode operation.
Disabled: Disable SNMP trap mode operation.
Trap Destination Configurations
Configure trap destinations on this page.
Name
Indicates the trap Configuration's name. Indicates the trap destination's name.
49
Enable
Indicates the trap destination mode operation. Possible modes are:
Enabled: Enable SNMP trap mode operation.
Disabled: Disable SNMP trap mode operation.
Version
Indicates the SNMP trap supported version. Possible versions are:
SNMPv1: Set SNMP trap supported version 1.
SNMPv2c: Set SNMP trap supported version 2c.
SNMPv3: Set SNMP trap supported version 3.
Trap Community
Indicates the community access string when sending SNMP trap packet. The allowed
string length is 0 to 255, and the allowed content is ASCII characters from 33 to 126.
Destination Address
Indicates the SNMP trap destination address. It allow a valid IP address in dotted
decimal notation ('x.y.z.w').
And it also allow a valid hostname. A valid hostname is a string drawn from the
alphabet (A-Za-z), digits (0-9), dot (.), dash (-). Spaces are not allowed, the first
character must be an alpha character, and the first and last characters must not be a
dot or a dash.
Indicates the SNMP trap destination IPv6 address. IPv6 address is in 128-bit records
represented as eight fields of up to four hexadecimal digits with a colon separating
each field (:). For example, 'fe80::215:c5ff:fe03:4dc7'. The symbol '::' is a special syntax
that can be used as a shorthand way of representing multiple 16-bit groups of
contiguous zeros; but it can appear only once. It can also represent a legally valid IPv4
address. For example, '::192.1.2.34'.
Destination port
Indicates the SNMP trap destination port. SNMP Agent will send SNMP message via
this port, the port range is 1~65535.
Trap Inform Mode
Indicates the SNMP trap inform mode operation. Possible modes are:
Enabled: Enable SNMP trap inform mode operation.
Disabled: Disable SNMP trap inform mode operation.
50
Trap Inform Timeout (seconds)
Indicates the SNMP trap inform timeout. The allowed range is 0 to 2147.
Trap Inform Retry Times
Indicates the SNMP trap inform retry times. The allowed range is 0 to 255.
Trap Probe Security Engine ID
Indicates the SNMP trap probe security engine ID mode of operation. Possible values
are:
Enabled: Enable SNMP trap probe security engine ID mode of operation.
Disabled: Disable SNMP trap probe security engine ID mode of operation.
Trap Security Engine ID
Indicates the SNMP trap security engine ID. SNMPv3 sends traps and informs using
USM for authentication and privacy. A unique engine ID for these traps and informs is
needed. When "Trap Probe Security Engine ID" is enabled, the ID will be probed
automatically. Otherwise, the ID specified in this field is used. The string must contain
an even number (in hexadecimal format) with number of digits between 10 and 64, but
all-zeros and all-'F's are not allowed.
Trap Security Name
Indicates the SNMP trap security name. SNMPv3 traps and informs using USM for
authentication and privacy. A unique security name is needed when traps and informs
are enabled.
51
2-5.1.7.3 Communities
The function is used to configure SNMPv3 communities. The Community and
UserName is unique. To create a new community account, please check <Add new
community> button, and enter the account information then check <Save>. Max
Group Number: 4.
Web Interface
To display the configure SNMP Communities in the web interface:
1. Click SNMP, Communities.
2. Click Add new community.
3. Specify the SNMP communities parameters.
4. Click Apply.
5. If you want to modify or clear the setting then click Reset.
Figure2-5.1.7.3: The SNMPv1/v2 Communities Security Configuration
Parameter description:
Delete
52
Check to delete the entry. It will be deleted during the next save.
Community
Indicates the community access string to permit access to SNMPv3 agent. The
allowed string length is 1 to 32, and the allowed content is ASCII characters from 33
to 126. The community string will be treated as security name and map a SNMPv1
or SNMPv2c community string.
Source IP
Indicates the SNMP access source address. A particular range of source addresses
can be used to restrict source subnet when combined with source mask.
Source Mask
Indicates the SNMP access source address mask
2-5.1.7.4 Users
The function is used to configure SNMPv3 user. The Entry index key is UserName. To
create a new UserName account, please check <Add new user> button, and enter the
user information then check <Save>. Max Group Number: 10.
Web Interface
To display the configure SNMP Users in the web interface:
1. Click SNMP, Users.
2. Specify the Privilege parameter.
3. Click Apply.
Figure 2-5.1.7.4: The SNMP Users Configuration
53
Parameter description:
Delete
Check to delete the entry. It will be deleted during the next save.
Engine ID
An octet string identifying the engine ID that this entry should belong to. The string
must contain an even number (in hexadecimal format) with number of digits
between 10 and 64, but all-zeros and all-'F's are not allowed. The SNMPv3
architecture uses the User-based Security Model (USM) for message security and
the View-based Access Control Model (VACM) for access control. For the USM entry,
the usmUserEngineID and usmUserName are the entry's keys. In a simple agent,
usmUserEngineID is always that agent's own snmpEngineID value. The value can
also take the value of the snmpEngineID of a remote SNMP engine with which this
user can communicate. In other words, if user engine ID equal system engine ID
then it is local user; otherwise it's remote user.
User Name
A string identifying the user name that this entry should belong to. The allowed
string length is 1 to 32, and the allowed content is ASCII characters from 33 to 126.
Security Level
Indicates the security model that this entry should belong to. Possible security
models are:
NoAuth, NoPriv: No authentication and no privacy.
Auth, NoPriv: Authentication and no privacy.
Auth, Priv: Authentication and privacy.
54
The value of security level cannot be modified if entry already exists. That means it
must first be ensured that the value is set correctly.
Authentication Protocol
Indicates the authentication protocol that this entry should belong to. Possible
authentication protocols are:
None: No authentication protocol.
MD5: An optional flag to indicate that this user uses MD5 authentication protocol.
SHA: An optional flag to indicate that this user uses SHA authentication protocol.
The value of security level cannot be modified if entry already exists. That means
must first ensure that the value is set correctly.
Authentication Password
A string identifying the authentication password phrase. For MD5 authentication
protocol, the allowed string length is 8 to 32. For SHA authentication protocol, the
allowed string length is 8 to 40. The allowed content is ASCII characters from 33 to
126.
Privacy Protocol
Indicates the privacy protocol that this entry should belong to. Possible privacy
protocols are:
None: No privacy protocol.
DES: An optional flag to indicate that this user uses DES authentication protocol.
Privacy Password
A string identifying the privacy password phrase. The allowed string length is 8 to
32, and the allowed content is ASCII characters from 33 to 126.
55
2-5.1.7.5 Group
The function is used to configure SNMPv3 group. The Entry index key are Security
Model and Security Name. To create a new group account, please check <Add new
group> button, and enter the group information then check <Save>. Max Group
Number: v1: 2, v2: 2, v3:10.
Web Interface
To display the configure SNMP Groups in the web interface:
1. Click SNMP, Groups.
2. Specify the Privilege parameter.
3. Click Apply.
Figure 2-5.1.7.5: The SNMP Groups Configuration
56
Parameter description:
Delete
Check to delete the entry. It will be deleted during the next save.
Security Model
Indicates the security model that this entry should belong to. Possible security
models are:
v1: Reserved for SNMPv1.
v2c: Reserved for SNMPv2c.
usm: User-based Security Model (USM).
Security Name
A string identifying the security name that this entry should belong to. The allowed
string length is 1 to 32, and the allowed content is ASCII characters from 33 to 126.
Group Name
A string identifying the group name that this entry should belong to. The allowed
string length is 1 to 32, and the allowed content is ASCII characters from 33 to 126.
57
2-5.1.7.6 Views
The function is used to configure SNMPv3 view. The Entry index keys are OID Subtree
and View Name. To create a new view account, please check <Add new view> button,
and enter the view information then check <Save>. Max Group Number: 28.
Configure SNMPv3 view table on this page. The entry index keys are View Name and
OID Subtree.
Web Interface
To display the configure SNMP views in the web interface:
1. Click SNMP, Views.
2. Click Add new View.
3. Specify the SNMP View parameters.
4. Click Apply.
5. If you want to modify or clear the setting then click Reset.
Figure 2-5.1.7.6: The SNMP Views Configuration
Parameter description:
58
Delete
Check to delete the entry. It will be deleted during the next save.
View Name
A string identifying the view name that this entry should belong to. The allowed
string length is 1 to 32, and the allowed content is ASCII characters from 33 to 126.
View Type
Indicates the view type that this entry should belong to. Possible view types are:
Included: An optional flag to indicate that this view subtree should be included.
Excluded: An optional flag to indicate that this view subtree should be excluded.
In general, if a view entry's view type is 'excluded', there should be another view
entry existing with view type as 'included' and it's OID subtree should overstep the
'excluded' view entry.
OID Subtree
The OID defining the root of the subtree to add to the named view. The allowed OID
length is 1 to 128. The allowed string content is digital number or asterisk(*).
2-5.1.7.7 Access
The function is used to configure SNMPv3 accesses. The Entry index key are Group
Name, Security Model and Security level. To create a new access account, please check
<Add new access> button, and enter the access information then check <Save>. Max
Group Number : 14
Web Interface
To display the configure SNMP Access in the web interface:
1. Click SNMP, Accesses.
2. Click Add new Access.
3. Specify the SNMP Access parameters.
4. Click Apply.
5. If you want to modify or clear the setting then click Reset.
.
59
Figure 2-5.1.7.7: The SNMP Accesses Configuration
Parameter description:
Delete
Check to delete the entry. It will be deleted during the next save.
Group Name
A string identifying the group name that this entry should belong to. The allowed
string length is 1 to 32, and the allowed content is ASCII characters from 33 to 126.
Security Model
Indicates the security model that this entry should belong to. Possible security
models are:
Any: Any security model accepted(v1|v2c|usm).
v1: Reserved for SNMPv1.
60
v2c: Reserved for SNMPv2c.
usm: User-based Security Model (USM).
Security Level
Indicates the security model that this entry should belong to. Possible security
models are:
NoAuth, NoPriv: No authentication and no privacy.
Auth, NoPriv: Authentication and no privacy.
Auth, Priv: Authentication and privacy.
Read View Name
The name of the MIB view defining the MIB objects for which this request may
request the current values. The allowed string length is 1 to 32, and the allowed
content is ASCII characters from 33 to 126.
Write View Name
The name of the MIB view defining the MIB objects for which this request may
potentially set new values. The allowed string length is 1 to 32, and the allowed
content is ASCII characters from 33 to 126.
2-5.1.8 RMON
An RMON implementation typically operates in a client/server model. Monitoring
devices contain RMON software agents that collect information and analyze packets.
These probes act as servers and the Network Management applications that
communicate with them act as clients.
2-5.1.8.1 Statistics
Configure RMON Statistics table on this page. The entry index key is ID.
Web Interface
To display the configure RMON configuration in the web interface:
61
1. Click RMON, Statistics.
2. Click Add New Entry.
3. Specify the ID parameters.
4. Click Apply.
Figure 2-5.1.8.1: The RMON Statics Configuration
Parameter description:
These parameters are displayed on the RMON Statistics Configuration page:
Delete
Check to delete the entry. It will be deleted during the next save.
ID
Indicates the index of the entry. The range is from 1 to 65535.
Data Source
Indicates the port ID which wants to be monitored. If in stacking switch, the value must
add 1000*(switch ID-1), for example, if the port is switch 3 port 5, the value is 2005
Interval
62
Indicates the interval in seconds for sampling the history statistics data. The range is
from 1 to 3600, default value is 1800 seconds.
Buckets
Indicates the maximum data entries associated this History control entry stored in
RMON. The range is from 1 to 3600, default value is 50.
Buckets Granted
The number of data shall be saved in the RMON.
2-5.1.8.2 History
Configure RMON History table on this page. The entry index key is ID.
Web Interface
To display the configure RMON History in the web interface:
1. Click RMON, History.
2. Click Add New Entry.
3. Specify the ID parameters.
4. Click Apply.
Figure 2-5.1.8.2: The RMON History Configuration
63
Parameter description:
These parameters are displayed on the RMON History Configuration page:
Delete
Check to delete the entry. It will be deleted during the next save.
ID
Indicates the index of the entry. The range is from 1 to 65535.
Data Source
Indicates the port ID which wants to be monitored. If in stacking switch, the value
must add 1000*(switch ID-1), for example, if the port is switch 3 port 5, the value is
2005
Interval
Indicates the interval in seconds for sampling the history statistics data. The range is
from 1 to 3600, default value is 1800 seconds.
Buckets
Indicates the maximum data entries associated this History control entry stored in
RMON. The range is from 1 to 3600, default value is 50.
Buckets Granted
The number of data shall be saved in the RMON.
2-5.1.8.3 Alarm
Configure RMON Alarm table on this page. The entry index key is ID.
64
Web Interface
To display the configure RMON Alarm in the web interface:
1. Click RMON, Alarm.
2. Click Add New Entry.
3. Specify the ID parameters.
4. Click Apply.
Figure 2-5.1.8.3: The RMON Alarm Configuration
Parameter description:
These parameters are displayed on the RMON Alarm Configuration page:
Delete
Check to delete the entry. It will be deleted during the next save.
ID
Indicates the index of the entry. The range is from 1 to 65535.
Interval
65
Indicates the interval in seconds for sampling and comparing the rising and falling
threshold. The range is from 1 to 2^31-1.
Variable
Indicates the particular variable to be sampled, the possible variables are:
InOctets:
The total number of octets received on the interface, including framing characters.
InUcastPkts:
The number of uni-cast packets delivered to a higher-layer protocol.
InNUcastPkts:
The number of broad-cast and multi-cast packets delivered to a higher-layer
protocol.
InDiscards:
The number of inbound packets that are discarded even the packets are normal.
InErrors:
The number of inbound packets that contained errors preventing them from being
deliverable to a higher-layer protocol.
InUnknownProtos:
the number of the inbound packets that were discarded because of the unknown or
un-support protocol.
OutOctets:
The number of octets transmitted out of the interface , including framing characters.
OutUcastPkts:
The number of uni-cast packets that request to transmit.
OutNUcastPkts:
The number of broad-cast and multi-cast packets that request to transmit.
OutDiscards:
The number of outbound packets that are discarded event the packets is normal.
OutErrors:
The The number of outbound packets that could not be transmitted because of
errors.
OutQLen:
66
The length of the output packet queue (in packets).
Sample Type
The method of sampling the selected variable and calculating the value to be
compared against the thresholds, possible sample types are:
Absolute: Get the sample directly.
Delta: Calculate the difference between samples (default).
Value
The value of the statistic during the last sampling period.
Startup Alarm
The method of sampling the selected variable and calculating the value to be
compared against the thresholds, possible sample types are:
RisingTrigger alarm when the first value is larger than the rising threshold.
FallingTrigger alarm when the first value is less than the falling threshold.
RisingOrFallingTrigger alarm when the first value is larger than the rising threshold
or less than the falling threshold (default).
Rising Threshold
Rising threshold value (-2147483648-2147483647).
Rising Index
Rising event index (1-65535).
Falling Threshold
Falling threshold value (-2147483648-2147483647)
Falling Index
Falling event index (1-65535).
2-5.1.8.4 Event
Configure RMON Event table on this page. The entry index key is ID.
67
Web Interface
To display the configure RMON Event in the web interface:
1. Click RMON, Event.
2. Click Add New Entry.
3. Specify the ID parameters.
4. Click Apply.
Figure 2-5.1.8.4: The RMON Event Configuration
Parameter description:
These parameters are displayed on the RMON History Configuration page:
Delete
Check to delete the entry. It will be deleted during the next save.
ID
Indicates the index of the entry. The range is from 1 to 65535.
Desc
Indicates this event, the string length is from 0 to 127, default is a null string.
Type
68
Indicates the notification of the event, the possible types are:
None: No SNMP log is created, no SNMP trap is sent.
Log: Create SNMP log entry when the event is triggered.
Snmp trap: Send SNMP trap when the event is triggered.
Log and trap: Create SNMP log entry and sent SNMP trap when the event is
triggered.
Community
Specify the community when trap is sent, the string length is from 0 to 127, default
is "public".
Event Last Time
Indicates the value of sysUpTime at the time this event entry last generated an
event.
2-5.2 Network
2-5.2.1 Limit Control
This section shows you to configure the Port Security settings of the Switch. You can
use the Port Security feature to restrict input to an interface by limiting and identifying
MAC addresses.
Web Interface
To configure a Configuration of Limit Control in the web interface:
1. Select “Enabled” in the Mode of System Configuration.
2. Checked Aging Enabled.
3. Set Aging Period (Default is 3600 seconds).
To configure a Port Configuration of Limit Control in the web interface:
1. Select “Enabled” in the Mode of Port Configuration.
69
2. Specify the maximum number of MAC addresses in the Limit of Port Configuration.
3. Set Action (Trap, Shutdown, Trap & Shutdown)
4. Click Apply.
Figure 2-5.2.1: The Port Security Limit Control Configuration
Parameter description:
System Configuration
Mode :
Indicates if Limit Control is globally enabled or disabled on the switch. If globally
disabled, other modules may still use the underlying functionality, but limit checks
and corresponding actions are disabled.
Aging Enabled :
If checked, secured MAC addresses are subject to aging as discussed under Aging
70
Period.
Aging Period :
If Aging Enabled is checked, then the aging period is controlled with this input. If
other modules are using the underlying port security for securing MAC addresses,
they may have other requirements to the aging period. The underlying port security
will use the shorter requested aging period of all modules that use the functionality.
The Aging Period can be set to a number between 10 and 10,000,000 seconds.
To understand why aging may be desired, consider the following scenario: Suppose
an end-host is connected to a 3rd party switch or hub, which in turn is connected to
a port on this switch on which Limit Control is enabled. The end-host will be
allowed to forward if the limit is not exceeded. Now suppose that the end-host logs
off or powers down. If it wasn't for aging, the end-host would still take up resources
on this switch and will be allowed to forward. To overcome this situation, enable
aging. With aging enabled, a timer is started once the end-host gets secured. When
the timer expires, the switch starts looking for frames from the end-host, and if such
frames are not seen within the next Aging Period, the end-host is assumed to be
disconnected, and the corresponding resources are freed on the switch.
Port Configuration
The table has one row for each port on the selected switch and a number of
columns, which are:
Port :
The port number to which the configuration below applies.
Mode :
Controls whether Limit Control is enabled on this port. Both this and the Global
Mode must be set to Enabled for Limit Control to be in effect. Notice that other
modules may still use the underlying port security features without enabling Limit
Control on a given port.
Action :
If Limit is reached, the switch can take one of the following actions:
None: Do not allow more than Limit MAC addresses on the port, but take no
further action.
Trap: If Limit + 1 MAC addresses is seen on the port, send an SNMP trap. If Aging is
71
disabled, only one SNMP trap will be sent, but with Aging enabled, new SNMP traps
will be sent every time the limit gets exceeded.
Shutdown: If Limit + 1 MAC addresses is seen on the port, shut down the port. This
implies that all secured MAC addresses will be removed from the port, and no new
address will be learned. Even if the link is physically disconnected and reconnected
on the port (by disconnecting the cable), the port will remain shut down. There are
three ways to re-open the port:
1) Boot the switch,
2) Disable and re-enable Limit Control on the port or the switch,
3) Click the Reopen button.
Trap & Shutdown: If Limit + 1 MAC addresses is seen on the port, both the "Trap"
and the "Shutdown" actions described above will be taken.
State :
This column shows the current state of the port as seen from the Limit Control's
point of view. The state takes one of four values:
Disabled: Limit Control is either globally disabled or disabled on the port.
Ready: The limit is not yet reached. This can be shown for all actions.
Limit Reached: Indicates that the limit is reached on this port. This state can only
be shown if Action is set to none or Trap.
Shutdown: Indicates that the port is shut down by the Limit Control module. This
state can only be shown if Action is set to shut down or Trap & Shutdown.
Re-open Button :
If a port is shut down by this module, you may reopen it by clicking this button,
which will only be enabled if this is the case. For other methods, refer to shut down
in the Action section.
NOTE: That clicking the reopen button causes the page to be
refreshed, so non-committed changes will be lost
Upper right icon (Refresh):
72
You can click them for refresh the Port Security information by manual.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
2-5.2.2 NAS
The section describes to configure the NAS parameters of the switch. The NAS server
can be employed to connect users to a variety of resources including Internet access,
conference calls, printing documents on shared printers, or by simply logging on to
the Internet.
Web Interface
To configure a Network Access Server in the web interface:
1. Select “Enabled” in the Mode of Network Access Server Configuration.
2. Checked Reauthentication Enabled.
3. Set Reauthentication Period (Default is 3600 seconds).
4. Set EAPOL Timeout (Default is 30 seconds).
5. Set Aging Period (Default is 300 seconds).
6. Set Hold Time (Default is 10 seconds).
7. Checked RADIUS-Assigned QoS Enabled.
8. Checked RADIUS-Assigned VLAN Enabled.
9. Checked Guest VLAN Enabled.
10. Specify Guest VLAN ID.
11. Specify Max. Reauth. Count.
12. Checked Allow Guest VLAN if EAPOL Seen.
13. Click Apply.
Figure 2-5.2.2: The Network Access Server Configuration
73
Parameter description:
Mode :
Indicates if NAS is globally enabled or disabled on the switch. If globally disabled, all
ports are allowed forwarding of frames.
Reauthentication Enabled :
If checked, successfully authenticated supplicants/clients are reauthenticated after
the interval specified by the Reauthentication Period. Reauthentication for
802.1X-enabled ports can be used to detect if a new device is plugged into a switch
port or if a supplicant is no longer attached.
For MAC-based ports, reauthentication is only useful if the RADIUS server
configuration has changed. It does not involve communication between the switch
and the client, and therefore doesn't imply that a client is still present on a port (see
Aging Period below).
74
Reauthentication Period :
Determines the period, in seconds, after which a connected client must be
reauthenticated. This is only active if the Reauthentication Enabled checkbox is
checked. Valid values are in the range 1 to 3600 seconds.
EAPOL Timeout :
Determines the time for retransmission of Request Identity EAPOL frames.
Valid values are in the range 1 to 255 seconds. This has no effect for MAC-based
ports.
Aging Period :
This setting applies to the following modes, i.e. modes using the Port Security
functionality to secure MAC addresses:
• Single 802.1X
• Multi 802.1X
• MAC-Based Auth.
When the NAS module uses the Port Security module to secure MAC addresses, the
Port Security module needs to check for activity on the MAC address in question at
regular intervals and free resources if no activity is seen within a given period of
time. This parameter controls exactly this period and can be set to a number
between 10 and 1000000 seconds.
If reauthentication is enabled and the port is in an 802.1X-based mode, this is not
so critical, since supplicants that are no longer attached to the port will get removed
upon the next re-authentication, which will fail. But if re-authentication is not
enabled, the only way to free resources is by aging the entries.
For ports in MAC-based Auth. mode, reauthentication doesn't cause direct
communication between the switch and the client, so this will not detect whether
the client is still attached or not, and the only way to free any resources is to age the
entry.
Hold Time :
This setting applies to the following modes, i.e. modes using the Port Security
functionality to secure MAC addresses:
• Single 802.1X
75
• Multi 802.1X
• MAC-Based Auth.
If a client is denied access - either because the RADIUS server denies the client
access or because the RADIUS server request times out (according to the timeout
specified on the "Configuration→Security→AAA" page) - the client is put on hold in
the Un-authorized state. The hold timer does not count during an on-going
authentication.
In MAC-based Auth. mode, the switch will ignore new frames coming from the
client during the hold time.
The Hold Time can be set to a number between 10 and 1000000 seconds.
Port Configuration :
The table has one row for each port on the selected switch and a number of
columns, which are:
Port :
The port number for which the configuration below applies.
Admin State :
If NAS is globally enabled, this selection controls the port's authentication mode.
The following modes are available:
Force Authorized :
In this mode, the switch will send one EAPOL Success frame when the port link
comes up, and any client on the port will be allowed network access without
authentication.
Force Unauthorized :
In this mode, the switch will send one EAPOL Failure frame when the port link
comes up, and any client on the port will be disallowed network access.
Port-based 802.1X :
In the 802.1X-world, the user is called the supplicant, the switch is the authenticator,
and the RADIUS server is the authentication server. The authenticator acts as the
man-in-the-middle, forwarding requests and responses between the supplicant and
the authentication server. Frames sent between the supplicant and the switch are
76
special 802.1X frames, known as EAPOL (EAP Over LANs) frames. EAPOL frames
encapsulate EAP PDUs (RFC3748). Frames sent between the switch and the RADIUS
server are RADIUS packets. RADIUS packets also encapsulate EAP PDUs together
with other attributes like the switch's IP address, name, and the supplicant's port
number on the switch. EAP is very flexible, in that it allows for different
authentication methods, like MD5-Challenge, PEAP, and TLS. The important thing is
that the authenticator (the switch) doesn't need to know which authentication
method the supplicant and the authentication server are using, or how many
information exchange frames are needed for a particular method. The switch simply
encapsulates the EAP part of the frame into the relevant type (EAPOL or RADIUS)
and forwards it.
When authentication is complete, the RADIUS server sends a special packet
containing a success or failure indication. Besides forwarding this decision to the
supplicant, the switch uses it to open up or block traffic on the switch port
connected to the supplicant
NOTE: Suppose two backend servers are enabled and that the
server timeout is configured to X seconds (using the AAA
configuration page), and suppose that the first server in the list
is currently down (but not considered dead).
Now, if the supplicant retransmits EAPOL Start frames at a rate
faster than X seconds, then it will never get authenticated,
because the switch will cancel on-going backend authentication
server requests whenever it receives a new EAPOL Start frame
from the supplicant.
And since the server hasn't yet failed (because the X seconds
haven't expired), the same server will be contacted upon the
next backend authentication server request from the switch. This
scenario will loop forever. Therefore, the server timeout should
be smaller than the supplicant's EAPOL Start frame
retransmission rate.
Single 802.1X :
77
In port-based 802.1X authentication, once a supplicant is successfully authenticated
on a port, the whole port is opened for network traffic. This allows other clients
connected to the port (for instance through a hub) to piggy-back on the
successfully authenticated client and get network access even though they really
aren't authenticated. To overcome this security breach, use the Single 802.1X variant.
Single 802.1X is really not an IEEE standard, but features many of the same
characteristics as does port-based 802.1X. In Single 802.1X, at most one supplicant
can get authenticated on the port at a time. Normal EAPOL frames are used in the
communication between the supplicant and the switch. If more than one supplicant
is connected to a port, the one that comes first when the port's link comes up will
be the first one considered. If that supplicant doesn't provide valid credentials
within a certain amount of time, another supplicant will get a chance. Once a
supplicant is successfully authenticated, only that supplicant will be allowed access.
This is the most secure of all the supported modes. In this mode, the Port Security
module is used to secure a supplicant's MAC address once successfully
authenticated.
Multi 802.1X :
In port-based 802.1X authentication, once a supplicant is successfully authenticated
on a port, the whole port is opened for network traffic. This allows other clients
connected to the port (for instance through a hub) to piggy-back on the
successfully authenticated client and get network access even though they really
aren't authenticated. To overcome this security breach, use the Multi 802.1X variant.
Multi 802.1X is really not an IEEE standard, but features many of the same
characteristics as does port-based 802.1X. Multi 802.1X is - like Single 802.1X - not
an IEEE standard, but a variant that features many of the same characteristics. In
Multi 802.1X, one or more supplicants can get authenticated on the same port at
the same time. Each supplicant is authenticated individually and secured in the MAC
table using the Port Security module.
In Multi 802.1X it is not possible to use the multicast BPDU MAC address as
destination MAC address for EAPOL frames sent from the switch towards the
supplicant, since that would cause all supplicants attached to the port to reply to
requests sent from the switch. Instead, the switch uses the supplicant's MAC address,
which is obtained from the first EAPOL Start or EAPOL Response Identity frame sent
by the supplicant. An exception to this is when no supplicants are attached. In this
case, the switch sends EAPOL Request Identity frames using the BPDU multicast
MAC address as destination - to wake up any supplicants that might be on the port.
78
The maximum number of supplicants that can be attached to a port can be limited
using the Port Security Limit Control functionality.
MAC-based Auth.:
Unlike port-based 802.1X, MAC-based authentication is not a standard, but merely
a best-practices method adopted by the industry. In MAC-based authentication,
users are called clients, and the switch acts as the supplicant on behalf of clients.
The initial frame (any kind of frame) sent by a client is snooped by the switch, which
in turn uses the client's MAC address as both username and password in the
subsequent EAP exchange with the RADIUS server. The 6-byte MAC address is
converted to a string on the following form "xx-xx-xx-xx-xx-xx", that is, a dash (-) is
used as separator between the lower-cased hexadecimal digits. The switch only
supports the MD5-Challenge authentication method, so the RADIUS server must be
configured accordingly.
When authentication is complete, the RADIUS server sends a success or failure
indication, which in turn causes the switch to open up or block traffic for that
particular client, using the Port Security module. Only then will frames from the
client be forwarded on the switch. There are no EAPOL frames involved in this
authentication, and therefore, MAC-based Authentication has nothing to do with
the 802.1X standard.
The advantage of MAC-based authentication over port-based 802.1X is that several
clients can be connected to the same port (e.g. through a 3rd party switch or a hub)
and still require individual authentication, and that the clients don't need special
supplicant software to authenticate. The advantage of MAC-based authentication
over 802.1X-based authentication is that the clients don't need special supplicant
software to authenticate. The disadvantage is that MAC addresses can be spoofed
by malicious users - equipment whose MAC address is a valid RADIUS user can be
used by anyone. Also, only the MD5-Challenge method is supported. The maximum
number of clients that can be attached to a port can be limited using the Port
Security Limit Control functionality.
RADIUS-Assigned QoS Enabled :
When RADIUS-Assigned QoS is both globally enabled and enabled (checked) on a
given port, the switch reacts to QoS Class information carried in the RADIUS
Access-Accept packet transmitted by the RADIUS server when a supplicant is
successfully authenticated. If present and valid, traffic received on the supplicant's
port will be classified to the given QoS Class. If (re-)authentication fails or the
79
RADIUS Access-Accept packet no longer carries a QoS Class or it's invalid, or the
supplicant is otherwise no longer present on the port, the port's QoS Class is
immediately reverted to the original QoS Class (which may be changed by the
administrator in the meanwhile without affecting the RADIUS-assigned).
This option is only available for single-client modes, i.e.
• Port-based 802.1X
• Single 802.1X
RADIUS attributes used in identifying a QoS Class:
Refer to the written documentation for a description of the RADIUS attributes
needed in order to successfully identify a QoS Class. The User-Priority-Table
attribute defined in RFC4675 forms the basis for identifying the QoS Class in an
Access-Accept packet.
Only the first occurrence of the attribute in the packet will be considered, and to be
valid, it must follow this rule:
• All 8 octets in the attribute's value must be identical and consist of ASCII
characters in the range '0' - '3', which translates into the desired QoS Class in the
range [0; 3].
RADIUS-Assigned VLAN Enabled :
When RADIUS-Assigned VLAN is both globally enabled and enabled (checked) for a
given port, the switch reacts to VLAN ID information carried in the RADIUS
Access-Accept packet transmitted by the RADIUS server when a supplicant is
successfully authenticated. If present and valid, the port's Port VLAN ID will be
changed to this VLAN ID, the port will be set to be a member of that VLAN ID, and
the port will be forced into VLAN unaware mode. Once assigned, all traffic arriving
on the port will be classified and switched on the RADIUS-assigned VLAN ID.
If (re-)authentication fails or the RADIUS Access-Accept packet no longer carries a
VLAN ID or it's invalid, or the supplicant is otherwise no longer present on the port,
the port's VLAN ID is immediately reverted to the original VLAN ID (which may be
changed by the administrator in the meanwhile without affecting the
RADIUS-assigned).
This option is only available for single-client modes, i.e.
• Port-based 802.1X
80
• Single 802.1X
For trouble-shooting VLAN assignments, use the "Monitor→VLANs→VLAN
Membership and VLAN Port" pages. These pages show which modules have
(temporarily) overridden the current Port VLAN configuration.
RADIUS attributes used in identifying a VLAN ID:
RFC2868 and RFC3580 form the basis for the attributes used in identifying a VLAN
ID in an Access-Accept packet. The following criteria are used:
• The Tunnel-Medium-Type, Tunnel-Type, and Tunnel-Private-Group-ID attributes
must all be present at least once in the Access-Accept packet.
• The switch looks for the first set of these attributes that have the same Tag value
and fulfil the following requirements (if Tag == 0 is used, the
Tunnel-Private-Group-ID does not need to include a Tag):
- Value of Tunnel-Medium-Type must be set to "IEEE-802" (ordinal 6).
- Value of Tunnel-Type must be set to "VLAN" (ordinal 13).
- Value of Tunnel-Private-Group-ID must be a string of ASCII chars in the range '0'
- '9', which is interpreted as a decimal string representing the VLAN ID. Leading '0's
are discarded. The final value must be in the range [1; 4095].
Guest VLAN Enabled :
When Guest VLAN is both globally enabled and enabled (checked) for a given port,
the switch considers moving the port into the Guest VLAN according to the rules
outlined below.
This option is only available for EAPOL-based modes, i.e.:
• Port-based 802.1X
• Single 802.1X
• Multi 802.1X
For trouble-shooting VLAN assignments, use the "Monitor→VLANs→VLAN
Membership and VLAN Port" pages. These pages show which modules have
(temporarily) overridden the current Port VLAN configuration.
Guest VLAN Operation:
When a Guest VLAN enabled port's link comes up, the switch starts transmitting
81
EAPOL Request Identity frames. If the number of transmissions of such frames
exceeds Max. Reauth. Count and no EAPOL frames have been received in the
meanwhile, the switch considers entering the Guest VLAN. The interval between
transmissions of EAPOL Request Identity frames is configured with EAPOL Timeout.
If Allow Guest VLAN if EAPOL Seen is enabled, the port will now be placed in the
Guest VLAN. If disabled, the switch will first check its history to see if an EAPOL
frame has previously been received on the port (this history is cleared if the port
link goes down or the port's Admin State is changed), and if not, the port will be
placed in the Guest VLAN. Otherwise it will not move to the Guest VLAN, but
continue transmitting EAPOL Request Identity frames at the rate given by EAPOL
Timeout.
Once in the Guest VLAN, the port is considered authenticated, and all attached
clients on the port are allowed access on this VLAN. The switch will not transmit an
EAPOL Success frame when entering the Guest VLAN.
While in the Guest VLAN, the switch monitors the link for EAPOL frames, and if one
such frame is received, the switch immediately takes the port out of the Guest VLAN
and starts authenticating the supplicant according to the port mode. If an EAPOL
frame is received, the port will never be able to go back into the Guest VLAN if the
"Allow Guest VLAN if EAPOL Seen" is disabled.
Port State :
The current state of the port. It can undertake one of the following values:
Globally Disabled: NAS is globally disabled.
Link Down: NAS is globally enabled, but there is no link on the port.
Authorized: The port is in Force Authorized or a single-supplicant mode and the
supplicant is authorized.
Unauthorized: The port is in Force Unauthorized or a single-supplicant mode and
the supplicant is not successfully authorized by the RADIUS server.
X Auth/Y Unauth: The port is in a multi-supplicant mode. Currently X clients are
authorized and Y are unauthorized.
Restart :
Two buttons are available for each row. The buttons are only enabled when
authentication is globally enabled and the port's Admin State is in an EAPOL-based
or MAC-based mode.
82
Clicking these buttons will not cause settings changed on the page to take effect.
Re-authenticate: Schedules a re-authentication whenever the quiet-period of the
port runs out (EAPOL-based authentication). For MAC-based authentication,
re-authentication will be attempted immediately.
The button only has effect for successfully authenticated clients on the port and will
not cause the clients to get temporarily unauthorized.
Reinitialize: Forces a re-initialization of the clients on the port and thereby a
re-authentication immediately. The clients will transfer to the unauthorized state
while the re-authentication is in progress.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
Upper right icon (Refresh):
You can click them for refresh the NAS Configuration by manual.
2-5.2.3 ACL
The IGP-1271 Series switch access control list (ACL) is probably the most commonly
used object in the IOS. It is used for packet filtering but also for selecting types of
traffic to be analyzed, forwarded, or influenced in some way. The ACLs are divided into
Ether Types. IPv4, ARP protocol, MAC and VLAN parameters etc. Here we will just go
over the standard and extended access lists for TCP/IP. As you create ACEs for ingress
classification, you can assign a policy for each port, the policy number is 1-8, and
however, each policy can be applied to any port. This makes it very easy to determine
what type of ACL policy you will be working with.
2-5.2.3.1 Ports
The section describes how to configure the ACL parameters (ACE) of the each switch
port. These parameters will affect frames received on a port unless the frame matches
a specific ACE
83
Web Interface
To configure the ACL Ports Configuration in the web interface:
1. Click Configuration, ACL, then Ports
2. To scroll the specific parameter value to select the correct value for port ACL
setting.
3. Click the save to save the setting
4. If you want to cancel the setting then you need to click the reset button. It will
revert to previously saved values.
5. After you configure complete then you could see the Counter of the port. Then
you could click refresh to update the counter or Clear the information.
Figure 2-5.2.3.1: The ACL Ports Configuration
Parameter description:
Port :
The logical port for the settings contained in the same row.
Policy ID :
Select the policy to apply to this port. The allowed values are 1 through 8. The
default value is 1.
Action :
84
Select whether forwarding is permitted ("Permit") or denied ("Deny"). The default
value is "Permit".
Rate Limiter ID :
Select which rate limiter to apply on this port. The allowed values are Disabled or
the values 1 through 16. The default value is "Disabled".
Port Redirect :
Select which port frames are redirected on. The allowed values are Disabled or a
specific port number and it can't be set when action is permitted. The default value
is "Disabled".
Logging :
Specify the logging operation of this port. The allowed values are:
Enabled: Frames received on the port are stored in the System Log.
Disabled: Frames received on the port are not logged.
The default value is "Disabled". Please note that the System Log memory size and
logging rate is limited.
Shutdown :
Specify the port shut down operation of this port. The allowed values are:
Enabled: If a frame is received on the port, the port will be disabled.
Disabled: Port shut down is disabled.
The default value is "Disabled".
State :
Specify the port state of this port. The allowed values are:
Enabled: To reopen ports by changing the volatile port configuration of the ACL
user module.
Disabled: To close ports by changing the volatile port configuration of the ACL user
module.
The default value is "Enabled"
Counter :
85
Counts the number of frames that match this ACE.
Buttons
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
Upper right icon (Refresh, clear)
You can click them for refresh the ACL Port Configuration or clear them by manual.
86
2-5.2.3.2 Rate Limiters
The section describes how to configure the switch’s ACL Rate Limiter parameters. The
Rate Limiter Level from 1 to 16 that allow user to set rate limiter value and units with
pps or kbps.
Web Interface
To configure ACL Rate Limiter in the web interface:
1. Click Configuration, ACL, then Rate Limiter
2. To specific the Rate field and the range from 0 to 3276700.
3. To scroll the Unit with pps or kbps
4. Click the Apply to save the setting
5. If you want to cancel the setting then you need to click the reset button. It will
revert to previously saved values.
Figure 2-5.2.3.2: The ACL Rate Limiter Configuration
Parameter description:
Rate Limiter ID :
The rate limiter ID for the settings contained in the same row.
Rate
The allowed values are: 0-3276700 in pps or 0, 100, 200, 300, ..., 1000000 in kbps.
87
Buttons
Apply – Click to save changes.
Reset - Click to undo any changes made locally and revert to previously saved
values.
2-5.2.3.3 Access Control List
The section describes how to configure Access Control List rule. An Access Control List
(ACL) is a sequential list of permit or deny conditions that apply to IP addresses, MAC
addresses, or other more specific criteria. This switch tests ingress packets against the
conditions in an ACL one by one. A packet will be accepted as soon as it matches a
permit rule, or dropped as soon as it matches a deny rule. If no rules match, the frame
is accepted. Other actions can also be invoked when a matching packet is found,
including rate limiting, copying matching packets to another port or to the system log,
or shutting down a port.
This page shows the Access Control List (ACL), which is made up of the ACEs defined
on this switch. Each row describes the ACE that is defined. The maximum number of
ACEs is 256 on each switch. Click on the lowest plus sign to add a new ACE to the list.
The reserved ACEs used for internal protocol, cannot be edited or deleted, the order
sequence cannot be changed the priority is highest
Web Interface
To configure Access Control List in the web interface:
1. Click Configuration, ACL, then Configuration
2. Click the button to add a new ACL, or use the other ACL
modification buttons to specify the editing action (i.e., edit, delete, or
moving the relative position of entry in the list)
3. To specific the parameter of the ACE
4. Click the save to save the setting
5. If you want to cancel the setting then you need to click the reset button.
It will revert to previously saved values.
6. When editing an entry on the ACE Configuration page, note that the
Items displayed depend on various selections, such as Frame Type and IP Protocol
Type. Specify the relevant criteria to be matched for this rule,
and set the actions to take when a rule is matched (such as Rate Limiter,
88
Port Copy, Logging, and Shutdown).
Figure 2-5.2.3.3: The ACL Rate Limiter Configuration
Parameter description:
Ingress Port :
Indicates the ingress port of the ACE. Possible values are:
Any: The ACE will match any ingress port.
Policy: The ACE will match ingress ports with a specific policy.
Port: The ACE will match a specific ingress port.
Policy / Bitmask :
Indicates the policy number and bitmask of the ACE.
Frame Type :
Indicates the frame type of the ACE. Possible values are:
89
Any: The ACE will match any frame type.
EType: The ACE will match Ethernet Type frames. Note that an Ethernet Type based
ACE will not get matched by IP and ARP frames.
ARP: The ACE will match ARP/RARP frames.
IPv4: The ACE will match all IPv4 frames.
IPv4/ICMP: The ACE will match IPv4 frames with ICMP protocol.
IPv4/UDP: The ACE will match IPv4 frames with UDP protocol.
IPv4/TCP: The ACE will match IPv4 frames with TCP protocol.
IPv4/Other: The ACE will match IPv4 frames, which are not ICMP/UDP/TCP. IPv6:
The ACE will match all IPv6 standard frames.
Action :
Indicates the forwarding action of the ACE.
Permit: Frames matching the ACE may be forwarded and learned.
Deny: Frames matching the ACE are dropped.
Filter: Frames matching the ACE are filtered.
Rate Limiter :
Indicates the rate limiter number of the ACE. The allowed range is 1 to 16. When
Disabled is displayed, the rate limiter operation is disabled.
Port Copy :
Indicates the port copy operation of the ACE. Frames matching the ACE are copied
to the port number. The allowed values are Disabled or a specific port number.
When Disabled is displayed, the port copy operation is disabled.
Logging :
Indicates the logging operation of the ACE. Possible values are:
Enabled: Frames matching the ACE are stored in the System Log.
Disabled: Frames matching the ACE are not logged.
Please note that the System Log memory size and logging rate is limited.
90
Shutdown :
Indicates the port shut down operation of the ACE. Possible values are:
Enabled: If a frame matches the ACE, the ingress port will be disabled.
Disabled: Port shut down is disabled for the ACE.
Counter :
The counter indicates the number of times the ACE was hit by a frame.
Modification Buttons
You can modify each ACE (Access Control Entry) in the table using the following
buttons:
: Inserts a new ACE before the current row.
: Edits the ACE row.
: Moves the ACE up the list.
: Moves the ACE down the list.
: Deletes the ACE.
: The lowest plus sign adds a new entry at the bottom of the ACE listings.
MAC Parameter:
SMAC Filter
(Only displayed when the frame type is Ethernet Type or ARP.)
Specify the source MAC filter for this ACE.
Any: No SMAC filter is specified. (SMAC filter status is "don't-care".)
Specific: If you want to filter a specific source MAC address with this ACE, choose
this value. A field for entering an SMAC value appears.
SMAC Value
When "Specific" is selected for the SMAC filter, you can enter a specific source MAC
address. The legal format is "xx-xx-xx-xx-xx-xx" or "xx.xx.xx.xx.xx.xx" or
"xxxxxxxxxxxx" (x is a hexadecimal digit). A frame that hits this ACE matches this
SMAC value.
91
DMAC Filter
Specify the destination MAC filter for this ACE.
Any: No DMAC filter is specified. (DMAC filter status is "don't-care".)
MC: Frame must be multicast.
BC: Frame must be broadcast.
UC: Frame must be unicast.
Specific: If you want to filter a specific destination MAC address with this ACE,
choose this value. A field for entering a DMAC value appears.
DMAC Value
When "Specific" is selected for the DMAC filter, you can enter a specific destination
MAC address. The legal format is "xx-xx-xx-xx-xx-xx" or "xx.xx.xx.xx.xx.xx" or
"xxxxxxxxxxxx" (x is a hexadecimal digit). A frame that hits this ACE matches this
DMAC value.
Buttons
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
Auto-refresh:
To evoke the auto-refresh to refresh the information automatically.
Upper right icon (Refresh, clear, Remove All)
You can click them for refresh the ACL configuration or clear them by manual.
Others remove all to clean up all ACL configurations on the table.
92
2-5.2.4 IP Source Guard
The section describes to configure the IP Source Guard detail parameters of the switch.
You could use the IP Source Guard configure to enable or disable with the Port of the
switch.
2-5.2.4.1 Configuration
This section describes how to configure IP Source Guard setting including：
Mode (Enabled and Disabled)
Maximum Dynamic Clients (0, 1, 2, Unlimited)
Web Interface
To configure an IP Source Guard Configuration in the web interface:
1. Select “Enabled” in the Mode of IP Source Guard Configuration.
2. Select “Enabled” of the specific port in the Mode of Port Mode Configuration.
3. Select Maximum Dynamic Clients (0, 1, 2, Unlimited) of the specific port in the
Mode of Port Mode Configuration.
4. Click Apply.
Figure 2-5.2.4.1: The IP Source Guard Configuration
Parameter description:
93
Mode of IP Source Guard Configuration :
Enable the Global IP Source Guard or disable the Global IP Source Guard. All
configured ACEs will be lost when the mode is enabled.
Port Mode Configuration :
Specify IP Source Guard is enabled on which ports. Only when both Global Mode
and Port Mode on a given port are enabled, IP Source Guard is enabled on this
given port.
Max Dynamic Clients :
Specify the maximum number of dynamic clients that can be learned on given port.
This value can be 0, 1, 2 or unlimited. If the port mode is enabled and the value of
max dynamic client is equal to 0, it means only allow the IP packets forwarding that
are matched in static entries on the specific port.
94
2-5.2.4.2 Static Table
The section describes to configure the Static IP Source Guard Table parameters of the
switch. You could use the Static IP Source Guard Table configure to manage the entries.
Web Interface
To configure a Static IP Source Guard Table Configuration in the web interface:
1. Click “Add new entry”.
2. Specify the Port, VLAN ID, IP Address, and MAC address in the entry.
3. Click Apply.
Figure 2-5.2.4.2: The Static IP Source Guard Table ///// ///
Parameter description:
Delete :
Check to delete the entry. It will be deleted during the next save.
Port :
95
The logical port for the settings.
VLAN ID :
The VLAN id for the settings.
IP Address :
Allowed Source IP address.
MAC address :
Allowed Source MAC address.
Adding new entry :
Click to add a new entry to the Static IP Source Guard table. Specify the Port, VLAN
ID, IP address, and IP Mask for the new entry. Click "Save".
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
2-5.2.5 ARP Inspection
The section describes to configure the ARP Inspection parameters of the switch. You
could use the ARP Inspection configure to manage the ARP table.
2-5.2.5.1 Port Configuration
This section describes how to configure ARP Inspection setting including：
Mode (Enabled and Disabled)
Port (Enabled and Disabled)
Web Interface
To configure an ARP Inspection Configuration in the web interface:
1. Select “Enabled” in the Mode of ARP Inspection Configuration.
2. Select “Enabled” of the specific port in the Mode of Port Mode Configuration.
3. Click Apply.
96
Figure 2-5.2.5.1: The ARP Inspection Configuration
Parameter description:
Mode of ARP Inspection Configuration :
Enable the Global ARP Inspection or disable the Global ARP Inspection.
Port Mode Configuration :
Specify ARP Inspection is enabled on which ports. Only when both Global Mode
and Port Mode on a given port are enabled, ARP Inspection is enabled on this given
port. Possible modes are:
Enabled: Enable ARP Inspection operation.
Disabled: Disable ARP Inspection operation.
If you want to inspect the VLAN configuration, you have to enable the setting of
"Check VLAN". The default setting of "Check VLAN" is disabled. When the setting of
"Check VLAN" is disabled, the log type of ARP Inspection will refer to the port
setting. And the setting of "Check VLAN" is enabled, the log type of ARP Inspection
will refer to the VLAN setting. Possible setting of "Check VLAN" are:
97
Enabled: Enable check VLAN operation.
Disabled: Disable check VLAN operation.
Only the Global Mode and Port Mode on a given port are enabled, and the setting
of "Check VLAN" is disabled, the log type of ARP Inspection will refer to the port
setting. There are four log types and possible types are:
None: Log nothing.
Deny: Log denied entries.
Permit: Log permitted entries.
ALL: Log all entries.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
2-5.2.5.2 VLAN Configuration
Each page shows up to 9999 entries from the VLAN table, default being 20, selected
through the "entries per page" input field. When first visited, the web page will show
the first 20 entries from the beginning of the VLAN Table. The first displayed will be the
one with the lowest VLAN ID found in the VLAN Table.
The "VLAN" input fields allow the user to select the starting point in the VLAN Table.
Clicking the button will update the displayed table starting from that or the closest
next VLAN Table match. The will use the next entry of the currently displayed VLAN
entry as a basis for the next lookup. When the end is reached the warning message is
shown in the displayed table. Use the button to start over.
Web Interface
To configure a VLAN Mode Configuration in the web interface:
1. Click “Add new entry”.
2. Specify the VLAN ID, Log Type
3. Click Apply.
Figure 2-5.2.5.2: The VLAN Mode Configuration
98
Parameter description:
VLAN Mode Configuration
Specify ARP Inspection is enabled on which VLANs. First, you have to enable the
port setting on Port mode configuration web page. Only when both Global Mode
and Port Mode on a given port are enabled, ARP Inspection is enabled on this given
port. Second, you can specify which VLAN will be inspected on VLAN mode
configuration web page. The log type also can be configured on per VLAN setting.
Possible types are:
None: Log nothing.
Deny: Log denied entries.
Permit: Log permitted entries.
ALL: Log all entries.
Buttons
Add New Entry: Click to add a new VLAN to the ARP Inspection VLAN table.
99
Apply: Click to save changes.
Reset: Click to undo any changes made locally and revert to previously saved
values.
100
2-5.2.5.3 Static Table
The section describes to configure the Static ARP Inspection Table parameters of the
switch. You could use the Static ARP Inspection Table configure to manage the ARP
entries.
Web Interface
To configure a Static ARP Inspection Table Configuration in the web interface:
1. Click Configuration, Security, Network, ARP Inspection and Static Table.
2. Specify the Port, VLAN ID, IP Address, and MAC address in the entry.
3. Click Apply.
Figure 2-5.2.5.3: The Static ARP Inspection Table
Parameter description:
Delete :
Check to delete the entry. It will be deleted during the next save.
101
Port :
The logical port for the settings.
VLAN ID :
The vlan id for the settings.
MAC Address :
Allowed Source MAC address in ARP request packets.
IP Address :
Allowed Source IP address in ARP request packets.
Adding new entry :
Click to add a new entry to the Static ARP Inspection table. Specify the Port, VLAN
ID, MAC address, and IP address for the new entry. Click "Save".
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
2-5.2.5.4 Dynamic Table
Entries in the Dynamic ARP Inspection Table are shown on this page. The Dynamic ARP
Inspection Table contains up to 1024 entries, and is sorted first by port, then by VLAN
ID, then by MAC address, and then by IP address.
Navigating the ARP Inspection Table
Each page shows up to 99 entries from the Dynamic ARP Inspection table, default
being 20, selected through the "entries per page" input field. When first visited, the
web page will show the first 20 entries from the beginning of the Dynamic ARP
Inspection Table.
The "Start from port address", "VLAN", "MAC address" and "IP address" input fields
allow the user to select the starting point in the Dynamic ARP Inspection Table.
Clicking the button will update the displayed table starting from that or the closest
next Dynamic ARP Inspection Table match. In addition, the two input fields will - upon
a button click - assume the value of the first displayed entry, allowing for continuous
102
refresh with the same start address.
The will use the last entry of the currently displayed table as a basis for the next lookup.
When the end is reached the text "No more entries" is shown in the displayed table.
Use the button to start over.
Web Interface
To configure a Dynamic ARP Inspection Table Configuration in the web interface:
1. Click Configuration, Security, Network, ARP Inspection and Dynamic Table
2. Specify the Port, VLAN ID, IP Address, and MAC address in the entry.
3. Click Apply.
Figure 2-5.2.5.4: The Dynamic ARP Inspection Table
Parameter description:
ARP Inspection Table Columns
Port
Switch Port Number for which the entries are displayed.
VLAN ID
VLAN-ID in which the ARP traffic is permitted.
MAC Address
103
User MAC address of the entry.
IP Address
User IP address of the entry.
Translate to static
Select the checkbox to translate the entry to static entry.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
Auto-refresh:
Check this box to refresh the page automatically. Automatic refresh occurs every 3
seconds.
Refresh:
Refreshes the displayed table starting from the input fields.
Save:
Click to save changes.
Reset:
Click to undo any changes made locally and revert to previously saved values.
<<:
Updates the table starting from the first entry in the Dynamic ARP Inspection
Table.
>>:
Updates the table, starting with the entry after the last entry currently displayed
2-5.3 AAA
This section shows you to use an AAA (Authentication, Authorization, and Accounting)
server to provide access control to your network. The AAA server can be a TACACS+ or
104
RADIUS server to create and manage objects that contain settings for using AAA
servers.
2-5.3.1 RADIUS
Web Interface
To configure a Common Configuration of AAA, RADIUS in the web interface:
1. Click Configuration, Security, AAA and RADIUS.
2. Specify the Parameter.
3. Click Apply.
Figure 2-5.3.1: The RADIUS Authentication Server Configuration
105
Parameter description:
Global Configuration
These setting are common for all of the RADIUS servers.
Timeout
Timeout is the number of seconds, in the range 1 to 1000, to wait for a reply from a
RADIUS server before retransmitting the request.
Retransmit
Retransmit is the number of times, in the range 1 to 1000, a RADIUS request is
retransmitted to a server that is not responding. If the server has not responded
after the last retransmit it is considered to be dead.
Deadtime
Deadtime, which can be set to a number between 0 to 1440 minutes, is the period
during which the switch will not send new requests to a server that has failed to
respond to a previous request. This will stop the switch from continually trying to
contact a server that it has already determined as dead.
Setting the Deadtime to a value greater than 0 (zero) will enable this feature, but
only if more than one server has been configured.
Key
The secret key - up to 63 characters long - shared between the RADIUS server and
the switch.
NAS-IP-Address (Attribute 4)
The IPv4 address to be used as attribute 4 in RADIUS Access-Request packets. If this
field is left blank, the IP address of the outgoing interface is used.
106
NAS-IPv6-Address (Attribute 95)
The IPv6 address to be used as attribute 95 in RADIUS Access-Request packets. If
this field is left blank, the IP address of the outgoing interface is used.
NAS-Identifier (Attribute 32)
The identifier - up to 255 characters long - to be used as attribute 32 in RADIUS
Access-Request packets. If this field is left blank, the NAS-Identifier is not included
in the packet.
Server Configuration
The table has one row for each RADIUS server and a number of columns, which are:
Delete
To delete a RADIUS server entry, check this box. The entry will be deleted during the
next Save.
Hostname
The IP address or hostname of the RADIUS server.
Auth Port
The UDP port to use on the RADIUS server for authentication.
Acct Port
The UDP port to use on the RADIUS server for accounting.
Timeout
This optional setting overrides the global timeout value. Leaving it blank will use the
global timeout value.
Retransmit
This optional setting overrides the global retransmit value. Leaving it blank will use
the global retransmit value.
Key
This optional setting overrides the global key. Leaving it blank will use the global
key.
107
Adding a New Server
Click to add a new RADIUS server. An empty row is added to the table, and the
RADIUS server can be configured as needed. Up to 5 servers are supported.
The button can be used to undo the addition of the new server.
Buttons
Apply:
Click to save changes.
Reset:
Click to undo any changes made locally and revert to previously saved values.
2-5.3.2 TACACS+
Web Interface
To configure a Common Configuration of AAA, TACACS+ in the web interface:
1. Click Configuration, Security, AAA and TACACS+.
2. Specify the Parameter.
3. Click Apply.
Figure 2-5.3.2: The TACACS+ Authentication Server Configuration
108
Parameter description:
Global Configuration
These setting are common for all of the TACACS+ servers.
Timeout
Timeout is the number of seconds, in the range 1 to 1000, to wait for a reply from a
TACACS+ server before it is considered to be dead.
Deadtime
Deadtime, which can be set to a number between 0 to 1440 minutes, is the period
during which the switch will not send new requests to a server that has failed to
respond to a previous request. This will stop the switch from continually trying to
contact a server that it has already determined as dead.
109
Setting the Deadtime to a value greater than 0 (zero) will enable this feature, but
only if more than one server has been configured.
Key
The secret key - up to 63 characters long - shared between the TACACS+ server and
the switch.
Server Configuration
The table has one row for each TACACS+ server and a number of columns, which
are:
Delete
To delete a TACACS+ server entry, check this box. The entry will be deleted during
the next Save.
Hostname
The IP address or hostname of the TACACS+ server.
Port
The TCP port to use on the TACACS+ server for authentication.
Timeout
This optional setting overrides the global timeout value. Leaving it blank will use the
global timeout value.
Key
This optional setting overrides the global key. Leaving it blank will use the global
key.
Adding a New Server
Click to add a new TACACS+ server. An empty row is added to the table, and the
TACACS+ server can be configured as needed. Up to 5 servers are supported.
The button can be used to undo the addition of the new server.
Buttons
Apply:
Click to save changes.
110
Reset:
Click to undo any changes made locally and revert to previously saved values.
2-6 Aggregation
The Aggregation is used to configure the settings of Link Aggregation. You can bundle
more than one port with the same speed, full duplex and the same MAC to be a single
logical port, thus the logical port aggregates the bandwidth of these ports. This means
you can apply your current Ethernet equipment’s to build the bandwidth aggregation.
For example, if there are three Fast Ethernet ports aggregated in a logical port, then
this logical port has bandwidth three times as high as a single Fast Ethernet port has.
2-6.1 Static
Ports using Static Trunk as their trunk method can choose their unique Static GroupID
to form a logic “trunked port”. The benefit of using Static Trunk method is that a port
can immediately become a member of a trunk group without any handshaking with its
peer port. This is also a disadvantage because the peer ports of your static trunk group
may not know that they should be aggregate together to form a “logic trunked port”.
Using Static Trunk on both end of a link is strongly recommended. Please also note
that low speed links will stay in “not ready” state when using static trunk to aggregate
with high speed links.
Web Interface
To configure the Trunk Aggregation Hash mode and Aggregation Group in the web
interface:
1. Click Configuration, Aggregation, Static and then Aggregation Mode Configuration.
2. Evoke to enable or disable the aggregation mode function.
Evoke Aggregation Group ID and Port members
3. Click the save to save the setting
4. If you want to cancel the setting then you need to click the reset button. It
will revert to previously saved values.
111
Figure 2-6.1: The Aggregation Mode Configuration
Parameter description:
Hash Code Contributors
Source MAC Address :
The Source MAC address can be used to calculate the destination port for the frame.
Check to enable the use of the Source MAC address, or uncheck to disable. By
default, Source MAC Address is enabled.
Destination MAC Address :
The Destination MAC Address can be used to calculate the destination port for the
frame. Check to enable the use of the Destination MAC Address, or uncheck to
disable. By default, Destination MAC Address is disabled.
IP Address :
The IP address can be used to calculate the destination port for the frame. Check to
enable the use of the IP Address, or uncheck to disable. By default, IP Address is
enabled.
112
TCP/UDP Port Number :
The TCP/UDP port number can be used to calculate the destination port for the
frame. Check to enable the use of the TCP/UDP Port Number, or uncheck to disable.
By default, TCP/UDP Port Number is enabled.
Aggregation Group Configuration
Group ID :
Indicates the group ID for the settings contained in the same row. Group ID
"Normal" indicates there is no aggregation. Only one group ID is valid per port.
Port Members :
Each switch port is listed for each group ID. Select a radio button to include a port in
an aggregation, or clear the radio button to remove the port from the aggregation.
By default, no ports belong to any aggregation group. Only full duplex ports can
join an aggregation and ports must be in the same speed in each group.
Buttons
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
2-6.2 LACP
This page allows the user to inspect the current LACP port configurations, and possibly
change them as well An LACP trunk group with more than one ready member-ports is
a “real trunked” group. An LACP trunk group with only one or less than one ready
member-ports is not a “real trunked” group.
Web Interface
To configure the Trunk Aggregation LACP parameters in the web interface:
1. Click Configuration, LACP, Configuration
2. Evoke to enable or disable the LACP on the port of the switch.
Scroll the Key parameter with Auto or Specific Default is Auto.
3. Scroll the Role with Active or Passive. Default is Active
4. Click the save to save the setting
113
5. If you want to cancel the setting then you need to click the reset button.
It will revert to previously saved values
Figure 2-6.2: The LACP Port Configuration
Parameter description:
Port :
The switch port number.
LACP Enabled
Controls whether LACP is enabled on this switch port. LACP will form an
aggregation when 2 or more ports are connected to the same partner.
Key
The Key value incurred by the port, range 1-65535 . The Auto setting will set the key
as appropriate by the physical link speed, 10Mb = 1, 100Mb = 2, 1Gb = 3. Using the
Specific setting, a user-defined value can be entered. Ports with the same Key value
can participate in the same aggregation group, while ports with different keys
cannot.
Role
The Role shows the LACP activity status. The Active will transmit LACP packets each
second, while Passive will wait for a LACP packet from a partner (speak if spoken to).
Timeout
114
The Timeout controls the period between BPDU transmissions. Fast will transmit
LACP packets each second, while Slow will wait for 30 seconds before sending a
LACP packet.
Prio
The Prio controls the priority of the port. If the LACP partner wants to form a larger
group than is supported by this device then this parameter will control which ports
will be active and which ports will be in a backup role. Lower number means greater
priority.
Buttons
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
2-7 Link OAM
2-7.1 Port Settings
This page allows the user to inspect the current Link OAM port configurations, and
change them as well.
Web Interface
To configure the Port Setting in the web interface:
1. Click Configuration, Link OAM and Event Settings.
2. Evoke Port members
3. Click the Apply to save the setting
Figure 2-7.1: The Port Setting
115
Parameter description:
Port
The switch port number.
OAM Enabled
Controls whether Link OAM is enabled on this switch port. Enabling Link OAM
provides the network operators the ability to monitor the health of the network and
quickly determine the location of failing links or fault conditions.
OAM Mode
Configures the OAM Mode as Active or Passive. The default mode is Passive.
Active mode
DTE's configured in Active mode initiate the exchange of Information OAMPDUs as
defined by the Discovery process. Once the Discovery process completes, Active
DTE's are permitted to send any OAMPDU while connected to a remote OAM peer
entity in Active mode. Active DTE's operate in a limited respect if the remote OAM
entity is operating in Passive mode. Active devices should not respond to OAM
remote loopback commands and variable requests from a Passive peer.
Passive mode
DTE's configured in Passive mode do not initiate the Discovery process. Passive
DTE's react to the initiation of the Discovery process by the remote DTE. This
eliminates the possibility of passive to passive links. Passive DTE's shall not send
Variable Request or Loopback Control OAMPDUs.
Loopback Support
Controls whether the loopback support is enabled for the switch port. Link OAM
remote loopback can be used for fault localization and link performance testing.
Enabling the loopback support will allow the DTE to execute the remote loopback
command that helps in the fault detection.
Link Monitor Support
Controls whether the Link Monitor support is enabled for the switch port. On
enabling the Link Monitor support, the DTE supports event notification that permits
the inclusion of diagnostic information.
116
MIB Retrieval Support
Controls whether the MIB Retrieval Support is enabled for the switch port. On
enabling the MIB retrieval support, the DTE supports polling of various Link OAM
based MIB variables' contents.
Loopback Operation
If the Loopback support is enabled, enabling this field will start a loopback
operation for the port.
Buttons
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
2-7.2 Event Settings
This page allows the user to inspect the current Link OAM Link Event configurations, and
change them as well.
Web Interface
To configure the Event Setting in the web interface:
1. Click Configuration, Link OAM and Event Settings.
2. Evoke Port members
3. Click the Apply to save the setting
Figure 2-7.2: The Event Settings
Parameter description:
Port :
117
The switch port number.
Event Name
Name of the Link Event which is being configured.
Error Window
Represents the window period in the order of 1 sec for the observation of various
link events.
Error Threshold
Represents the threshold value for the window period for the appropriate Link event
so as to notify the peer of this error.
Error Frame Event
The Errored Frame Event counts the number of errored frames detected during the
specified period. The period is specified by a time interval ( Window in order of 1
sec). This event is generated if the errored frame count is equal to or greater than
the specified threshold for that period (Period Threshold). Errored frames are frames
that had transmission errors as detected at the Media Access Control sublayer. Error
Window for 'Error Frame Event' must be an integer value between 1-60 and its
default value is '1'. Whereas Error Threshold must be between 0-4294967295 and its
default value is '0'.
Symbol Period Error Event
The Errored Symbol Period Event counts the number of symbol errors that occurred
during the specified period. The period is specified by the number of symbols that
can be received in a time interval on the underlying physical layer. This event is
generated if the symbol error count is equal to or greater than the specified
threshold for that period. Error Window for 'Symbol Period Error Event' must be an
integer value between 1-60 and its default value is '1'. Whereas Error Threshold
must be between 0-4294967295 and its default value is '0'.
Seconds Summary Event
The Errored Frame Seconds Summary Event TLV counts the number of errored
frame seconds that occurred during the specified period. The period is specified by
a time interval. This event is generated if the number of errored frame seconds is
equal to or greater than the specified threshold for that period. An errored frame
second is a one second interval wherein at least one frame error was detected.
Errored frames are frames that had transmission errors as detected at the Media
Access Control sublayer. Error Window for 'Seconds Summary Event' must be an
integer value between 10-900 and its default value is '60'. Whereas Error Threshold
must be between 0-65535 and its default value is '1'.
Buttons
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
118
2-8 Loop Protection
The loop Protection is used to detect the presence of traffic. When switch receives
packet’s (looping detection frame) MAC address the same as oneself from port, show
Loop Protection happens. The port will be locked when it received the looping
Protection frames. If you want to resume the locked port, please find out the looping
path and take off the looping path, then select the resume the locked port and click on
“Resume” to turn on the locked ports.
Web Interface
To configure the Loop Protection parameters in the web interface:
1. Click Configuration, Loop Protection.
2. Evoke to select enable or disable the port loop Protection
3. Click the save to save the setting
4. If you want to cancel the setting then you need to click the Reset button. It will
revert to previously saved values
Figure 2-8: The Loop Protection Configuration.
119
Parameter description:
Enable Loop Protection:
Controls whether loop protections is enabled (as a whole).
Transmission Time:
The interval between each loop protection PDU sent on each port. Valid values are 1
to 10 seconds.
Shutdown Time:
The period (in seconds) for which a port will be kept disabled in the event of a loop
is detected (and the port action shuts down the port). Valid values are 0 to 604800
seconds (7 days). A value of zero will keep a port disabled (until next device restart).
Port No:
The switch port number of the port.
Enable :
Controls whether loop protection is enabled on this switch port
Action:
Configures the action performed when a loop is detected on a port. Valid values are
Shutdown Port, Shutdown Port and Log or Log Only.
Tx Mode :
Controls whether the port is actively generating loop protection PDU's, or whether it is just
passively looking for looped PDU's.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
120
2-9 Spanning Tree
The Spanning Tree Protocol (STP) can be used to detect and disable network loops,
and to provide backup links between switches, bridges or routers. This allows the
switch to interact with other bridging devices (that is, an STP-compliant switch, bridge
or router) in your network to ensure that only one route exists between any two
stations on the network, and provide backup links which automatically take over when
a primary link goes down.
STP - STP uses a distributed algorithm to select a bridging device (STP- compliant
switch, bridge or router) that serves as the root of the spanning tree network. It selects
a root port on each bridging device (except for the root device) which incurs the
lowest path cost when forwarding a packet from that device to the root device. Then it
selects a designated bridging device from each LAN which incurs the lowest path cost
when forwarding a packet from that LAN to the root device. All ports connected to
designated bridging devices are assigned as designated ports. After determining the
lowest cost spanning tree, it enables all root ports and designated ports, and disables
all other ports. Network packets are therefore only forwarded between root ports and
designated ports, eliminating any possible network loops.
Once a stable network topology has been established, all bridges listen for Hello
BPDUs (Bridge Protocol Data Units) transmitted from the Root Bridge. If a bridge does
not get a Hello BPDU after a predefined interval (Maximum Age), the bridge assumes
that the link to the Root Bridge is down. This bridge will then initiate negotiations with
other bridges to reconfigure the network to reestablish a valid network topology.
2-9.1 Bridge Setting
121
The section describes that how to configure the Spanning Tree Bridge and STP System
settings. It allows you to configure STP System settings are used by all STP Bridge
instance in the switch.
Web Interface
To configure the Spanning Tree Bridge Settings parameters in the web interface:
1. Click Configuration, Spanning Tree, Bridge Settings
2. Scroll to select the parameters and write down available value of parameters in
blank field in Basic Settings
3. Evoke to enable or disable the parameters and write down available value of
parameters in blank field in Advanced settings
4. Click the apply to save the setting
5. If you want to cancel the setting then you need to click the Reset button. It will
revert to previously saved values
122
Figure 2-9.1: The STP Bridge Configuration
Parameter description:
Basic Settings
Protocol Version :
The STP protocol version setting. Valid values are STP, RSTP and MSTP.
Bridge Priority :
Controls the bridge priority. Lower numeric values have better priority. The bridge
priority plus the MSTI instance number, concatenated with the 6-byte MAC address
of the switch forms a Bridge Identifier. For MSTP operation, this is the priority of the
CIST. Otherwise, this is the priority of the STP/RSTP Bridge.
Forward Delay :
The delay used by STP Bridges to transit Root and Designated Ports to Forwarding
(used in STP compatible mode). Valid values are in the range 4 to 30 seconds.
Max Age :
The maximum age of the information transmitted by the Bridge when it is the Root
Bridge. Valid values are in the range 6 to 40 seconds, and MaxAge must be <=
123
(FwdDelay-1)*2.
Maximum Hop Count :
This defines the initial value of remaining Hops for MSTI information generated at
the boundary of an MSTI region. It defines how many bridges a root bridge can
distribute its BPDU information to. Valid values are in the range 6 to 40 hops.
Transmit Hold Count :
The number of BPDU's a bridge port can send per second. When exceeded,
transmission of the next BPDU will be delayed. Valid values are in the range 1 to 10
BPDU's per second.
Advanced Settings
Edge Port BPDU Filtering :
Control whether a port explicitly configured as Edge will transmit and receive
BPDUs.
Edge Port BPDU Guard :
Control whether a port explicitly configured as Edge will disable itself upon
reception of a BPDU. The port will enter the error-disabled state, and will be
removed from the active topology.
Port Error Recovery :
Control whether a port in the error-disabled state automatically will be enabled
after a certain time. If recovery is not enabled, ports have to be disabled and
re-enabled for normal STP operation. The condition is also cleared by a system
reboot.
Port Error Recovery Timeout :
The time to pass before a port in the error-disabled state can be enabled. Valid
values are between 30 and 86400 seconds (24 hours).
Buttons
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
124
2-9.2 MSTI Mapping
When you implement a Spanning Tree protocol on the switch that the bridge instance.
The CIST is not available for explicit mapping, as it will receive the VLANs not explicitly
mapped. Due to the reason that you need to set the list of VLANs mapped to the MSTI.
The VLANs must be separated with comma and/or space. A VLAN can only be mapped
to one MSTI. An unused MSTI should just be left empty. (I.e. not having any VLANs
mapped to it.)
This section describes it allows the user to inspect the current STP MSTI bridge
instance priority configurations, and possibly change them as well.
Web Interface
To configure the Spanning Tree MSTI Mapping parameters in the web interface:
1. Click Configuration, Spanning Tree, MSTI Mapping
2. Specify the configuration identification parameters in the field. Specify the VLANs
Mapped blank field.
3. Click the save to save the setting
4. If you want to cancel the setting then you need to click the Reset button. It will revert
to previously saved values
Figure 2-9.2: The MSTI Configuration
125
Parameter description:
Configuration Identification
Configuration Name :
The name identifying the VLAN to MSTI mapping. Bridges must share the name and
revision (see below), as well as the VLAN-to-MSTI mapping configuration in order
to share spanning trees for MSTI's (Intra-region). The name is at most 32 characters.
Configuration Revision :
The revision of the MSTI configuration named above. This must be an integer
between 0 and 65535.
MSTI :
The bridge instance. The CIST is not available for explicit mapping, as it will receive
the VLANs not explicitly mapped.
126
VLANs Mapped :
The list of VLANs mapped to the MSTI. The VLANs can be given as a single (xx, xx
being between 1 and 4094) VLAN, or a range (xx-yy), each of which must be
separated with comma and/or space. A VLAN can only be mapped to one MSTI. An
unused MSTI should just be left empty. (I.e. not having any VLANs mapped to it.)
Example: 2,5,20-40.
127
2-9.3 MSTI Priorities
When you implement a Spanning Tree protocol on the switch that the bridge instance.
The CIST is the default instance which is always active. For controls the bridge priority.
Lower numeric values have better priority. The bridge priority plus the MSTI instance
number, concatenated with the 6-byte MAC address of the switch forms a Bridge
Identifier
The section describes it allows the user to inspect the current STP MSTI bridge
instance priority configurations, and possibly change them as well.
Web Interface
To configure the Spanning Tree MSTI Priorities parameters in the web interface:
1. Click Configuration, Spanning Tree, MSTI Priorities
2. Scroll the Priority maximum is 240. Default is 128.
3. Click the save to save the setting
4. If you want to cancel the setting then you need to click the Reset button. It will
revert to previously saved values
Figure 2-9.3: The MSTI Configuration
128
Parameter description:
MSTI :
The bridge instance. The CIST is the default instance, which is always active.
Priority :
Controls the bridge priority. Lower numeric values have better priority. The bridge
priority plus the MSTI instance number, concatenated with the 6-byte MAC address
of the switch forms a Bridge Identifier.
Buttons
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
2-9.4 CIST Ports
When you implement an Spanning Tree protocol on the switch that the bridge
instance. You need to configure the CIST Ports. The section describes it allows the user
to inspect the to inspect the current STP CIST port configurations, and possibly change
them as well.
129
Web Interface
To configure the Spanning Tree CIST Ports parameters in the web interface:
1. Click Configuration, Spanning Tree, CIST Ports
2. Scroll and evoke to set all parameters of CIST Aggregated Port Configuration.
3. Evoke to enable or disable the STP, then scroll and evoke to set all parameters of
the CIST normal Port configuration.
4. Click the apply to save the setting
5. If you want to cancel the setting then you need to click the Reset button. It will
revert to previously saved values
Figure 2-9.4: The STP CIST Port Configuration
Parameter description:
Port :
The switch port number of the logical STP port.
STP Enabled :
130
Controls whether STP is enabled on this switch port.
Path Cost :
Controls the path cost incurred by the port. The Auto setting will set the path cost
as appropriate by the physical link speed, using the 802.1D recommended values.
Using the Specific setting, a user-defined value can be entered. The path cost is
used when establishing the active topology of the network. Lower path cost ports
are chosen as forwarding ports in favor of higher path cost ports. Valid values are in
the range 1 to 200000000.
Priority :
Controls the port priority. This can be used to control priority of ports having
identical port cost. (See above).
operEdge (state flag) :
Operational flag describing whether the port is connecting directly to edge devices.
(No Bridges attached). Transition to the forwarding state is faster for edge ports
(having operEdge true) than for other ports.The value of this flag is based on
AdminEdge and AutoEdge fields. This flag is displayed as Edge in
Monitor->Spanning Tree -> STP Detailed Bridge Status.
AdminEdge :
Controls whether the operEdge flag should start as set or cleared. (The initial
operEdge state when a port is initialized).
AutoEdge :
Controls whether the bridge should enable automatic edge detection on the bridge
port. This allows operEdge to be derived from whether BPDU's are received on the
port or not.
Restricted Role :
If enabled, causes the port not to be selected as Root Port for the CIST or any MSTI,
even if it has the best spanning tree priority vector. Such a port will be selected as
an Alternate Port after the Root Port has been selected. If set, it can cause lack of
spanning tree connectivity. It can be set by a network administrator to prevent
bridges external to a core region of the network influence the spanning tree active
topology, possibly because those bridges are not under the full control of the
administrator. This feature is also known as Root Guard.
131
Restricted TCN :
If enabled, causes the port not to propagate received topology change notifications
and topology changes to other ports. If set it can cause temporary loss of
connectivity after changes in a spanning tree's active topology as a result of
persistently incorrect learned station location information. It is set by a network
administrator to prevent bridges external to a core region of the network, causing
address flushing in that region, possibly because those bridges are not under the
full control of the administrator or the physical link state of the attached LANs
transits frequently.
BPDU Guard :
If enabled, causes the port to disable itself upon receiving valid BPDU's. Contrary to
the similar bridge setting, the port Edge status does not affect this setting. A port
entering error-disabled state due to this setting is subject to the bridge Port Error
Recovery setting as well.
Point to Point
Controls whether the port connects to a point-to-point LAN rather than to a shared
medium. This can be automatically determined, or forced either true or false.
Transition to the forwarding state is faster for point-to-point LANs than for shared
media.
Buttons
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
2-9.5 MSTI Ports
The section describes it allows the user to inspect the current STP MSTI port
configurations, and possibly change them as well.
An MSTI port is a virtual port, which is instantiated separately for each active CIST
(physical) port for each MSTI instance configured on and applicable to the port. The
MSTI instance must be selected before displaying actual MSTI port configuration
options. It contains MSTI port settings for physical and aggregated ports.
132
Web Interface
To configure the Spanning Tree MSTI Port Configuration parameters in the web
interface:
1. Click Configuration, Spanning Tree, MSTI Ports
2. Scroll to select the MST1 or other MSTI Port
3. Click Get to set the detail parameters of the MSTI Ports.
4. Scroll to set all parameters of the MSTI Port configuration.
5. Click the save to save the setting
6. If you want to cancel the setting then you need to click the Reset button. It will
revert to previously saved values
Figure 2-9.5: The MSTI Port Configuration
Parameter description:
133
Port :
The switch port number of the corresponding STP CIST (and MSTI) port.
Path Cost :
Controls the path cost incurred by the port. The Auto setting will set the path cost
as appropriate by the physical link speed, using the 802.1D recommended values.
Using the Specific setting, a user-defined value can be entered. The path cost is
used when establishing the active topology of the network. Lower path cost ports
are chosen as forwarding ports in favor of higher path cost ports. Valid values are in
the range 1 to 200000000.
Priority :
Controls the port priority. This can be used to control priority of ports having
identical port cost. (See above).
Buttons
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
2-10 IPMC Profile
This page provides IPMC Profile related configurations.
2-10.1 Profile Table
The IPMC profile is used to deploy the access control on IP multicast streams. It is
allowed to create at maximum 64 Profiles with at maximum 128 corresponding rules
for each.
Web Interface
To configure the IPMC Profile Configuration in the web interface:
1. Click Configuration, IPMC Profile, Profile Table
2. Evoke to enable or disable the IPMC Profile parameter.
3. Click Apply
134
Figure 2-10.1: The IPMC Profile Configuration
135
Parameter description:
Global Profile Mode
Enable/Disable the Global IPMC Profile.
System starts to do filtering based on profile settings only when the global profile
mode is enabled.
Delete
Check to delete the entry.
The designated entry will be deleted during the next save.
Profile Name
The name used for indexing the profile table.
Each entry has the unique name which is composed of at maximum 16 alphabetic and
numeric characters. At least one alphabet must be present.
Profile Description
Additional description, which is composed of at maximum 64 alphabetic and numeric
characters, about the profile.
No blank or space characters are permitted as part of description. Use "_" or "-" to
separate the description sentence.
Rule
When the profile is created, click the edit button to enter the rule setting page of the
designated profile. Summary about the designated profile will be shown by clicking
the view button. You can manage or inspect the rules of the designated profile by
using the following buttons:
: List the rules associated with the designated profile.
: Adjust the rules associated with the designated profile.
Buttons
Add New IPMC Profile – Click to add new IPMC profile. Specify the name and
configure the new entry. Click "Save".
Apply – Click to save changes.
Reset – Click to undo any changes made locally and revert to previously saved values.
2-10.2 Address Entry
This page provides address range settings used in IPMC profile.
The address entry is used to specify the address range that will be associated with
IPMC Profile. It is allowed to create at maximum 128 address entries in the system.
136
Web Interface
To configure the IPMC Profile Address Configuration in the web interface:
1. Click Configuration, IPMC Profile, Address Entry.
2. Specify the Entry Name, Start Address, End Address.
3. Click Apply
Figure 2-10.2: The IPMC Profile Address Configuration
Parameter description:
Delete
Check to delete the entry.
The designated entry will be deleted during the next save.
Entry Name
The name used for indexing the address entry table.
Each entry has the unique name which is composed of at maximun 16 alphabetic
137
and numeric characters. At least one alphabet must be present.
Start Address
The starting IPv4/IPv6 Multicast Group Address that will be used as an address
range.
End Address
The ending IPv4/IPv6 Multicast Group Address that will be used as an address
range.
Buttons
Add New Address (Range) Entry – Click to add new address range. Specify the
name and configure the addresses. Click "Save"
Apply – Click to save changes.
Reset – Click to undo any changes made locally and revert to previously saved values.
Refresh – Refreshes the displayed table starting from the input fields.
<< – Updates the table starting from the first entry in the IPMC Profile Address
Configuration.
>> – Updates the table, starting with the entry after the last entry currently displayed.
2-11MVR
The MVR feature enables multicast traffic forwarding on the Multicast VLAN. In a
multicast television application, a PC or a television with a set-top box can receive
the multicast stream. Multiple set-top boxes or PCs can be connected to one
subscriber port, which is a switch port configured as an MVR receiver port. When a
subscriber selects a channel, the set-top box or PC sends an IGMP join message to
Switch A to join the appropriate multicast. Uplink ports that send and receive
multicast data to and from the multicast VLAN are called MVR source ports.
Web Interface
To configure the MVR Configuration in the web interface:
1. Click Configuration, MVR, Configuration
2. Scroll the MVR mode to enable or disable and Scroll to set all parameters.
3. Click the save to save the setting
138
4. If you want to cancel the setting then you need to click the Reset button. It will
revert to previously saved values
Figure 2-11: The MVR Configuration
139
Parameter description:
MVR Mode
Enable/Disable the Global MVR.
The Unregistered Flooding control depends on the current configuration in
IGMP/MLD Snooping. It is suggested to enable Unregistered Flooding control when
the MVR group table is full.
Delete
Check to delete the entry. The designated entry will be deleted during the next
save.
MVR VID
Specify the Multicast VLAN ID.
Be Caution: MVR source ports are not recommended to be overlapped with
management VLAN ports.
MVR Name
MVR Name is an optional attribute to indicate the name of the specific MVR VLAN.
Maximum length of the MVR VLAN Name string is 32. MVR VLAN Name can only
contain alphabets or numbers. When the optional MVR VLAN name is given, it
should contain at least one alphabet. MVR VLAN name can be edited for the
existing MVR VLAN entries or it can be added to the new entries.
IGMP Address
Define the IPv4 address as source address used in IP header for IGMP control
frames.
The default IGMP address is not set (0.0.0.0).
When the IGMP address is not set, system uses IPv4 management address of the IP
interface associated with this VLAN.
When the IPv4 management address is not set, system uses the first available IPv4
management address.
Otherwise, system uses a pre-defined value. By default, this value will be 192.0.2.1.
Mode
Specify the MVR mode of operation. In Dynamic mode, MVR allows dynamic MVR
140
membership reports on source ports. In Compatible mode, MVR membership
reports are forbidden on source ports. The default is Dynamic mode.
Tagging
Specify whether the traversed IGMP/MLD control frames will be sent as Untagged
or Tagged with MVR VID. The default is tagged.
Priority
Specify how the traversed IGMP/MLD control frames will be sent in prioritized
manner. The default Priority is 0.
LLQI
Define the maximum time to wait for IGMP/MLD report memberships on a receiver
port before removing the port from multicast group membership. The value is in
units of tenths of a seconds. The range is from 0 to 31744. The default LLQI is 5
tenths or one-half second.
Interface Channel Setting
When the MVR VLAN is created, click the Edit symbol to expand the corresponding
multicast channel settings for the specific MVR VLAN. Summary about the Interface
Channel Setting (of the MVR VLAN) will be shown besides the Edit symbol.
Port
The logical port for the settings.
Port Role
Configure an MVR port of the designated MVR VLAN as one of the following roles.
Inactive: The designated port does not participate MVR operations.
Source: Configure uplink ports that receive and send multicast data as source ports.
Subscribers cannot be directly connected to source ports.
Receiver: Configure a port as a receiver port if it is a subscriber port and should
only receive multicast data. It does not receive data unless it becomes a member of
the multicast group by issuing IGMP/MLD messages.
Be Caution: MVR source ports are not recommended to be overlapped with
management VLAN ports. Select the port role by clicking the Role symbol to switch
the setting. I indicates Inactive; S indicates Source; R indicates Receiver. The default
141
Role is Inactive.
Immediate Leave
Enable the fast leave on the port.
2-12 IPMC
ICMP is an acronym for Internet Control Message Protocol. It is a protocol that
generated the error response, diagnostic or routing purposes. ICMP messages
generally contain information about routing difficulties or simple exchanges such as
time-stamp or echo transactions.
2-12.1 IGMP Snooping
The function, is used to establish the multicast groups to forward the multicast packet
to the member ports, and, in nature, avoids wasting the bandwidth while IP multicast
packets are running over the network. This is because a switch that does not support
IGMP or IGMP Snooping cannot tell the multicast packet from the broadcast packet,
so it can only treat them all as the broadcast packet. Without IGMP Snooping, the
multicast packet forwarding function is plain and nothing is different from broadcast
packet.
A switch supported IGMP Snooping with the functions of query, report and leave, a
type of packet exchanged between IP Multicast Router/Switch and IP Multicast Host,
can update the information of the Multicast table when a member (port) joins or
leaves an IP Multicast Destination Address. With this function, once a switch receives
an IP multicast packet, it will forward the packet to the members who joined in a
specified IP multicast group before.
The packets will be discarded by the IGMP Snooping if the user transmits multicast
packets to the multicast group that had not been built up in advance. IGMP mode
enables the switch to issue IGMP function that you enable IGMP proxy or snooping on
the switch, which connects to a router closer to the root of the tree. This interface is
the upstream interface. The router on the upstream interface should be running IGMP.
2-12.1.1 Basic Configuration
The section describes how to set the basic IGMP snooping on the switch, which
142
connects to a router closer to the root of the tree. This interface is the upstream
interface. The router on the upstream interface should be running IGMP
Web Interface
To configure the IGMP Snooping parameters in the web interface:
1. Click Configuration, IPMC,IGMP Snooping, Basic Configuration
2. Evoke to select enable or disable which Global configuration
3. Evoke which port wants to become a Router Port or enable/ disable the Fast Leave
function..
4. Scroll to set the Throtting parameter.
5. Click the apply to save the setting
6. If you want to cancel the setting then you need to click the Reset button. It will
revert to previously saved values
Figure 2-12.1.1: The IGMP Snooping Configuration.
Parameter description:
143
Snooping Enabled:
Enable the Global IGMP Snooping.
Unregistered IPMCv4 Flooding enabled :
Enable unregistered IPMCv4 traffic flooding.
IGMP SSM Range :
SSM (Source-Specific Multicast) Range allows the SSM-aware hosts and routers run
the SSM service model for the groups in the address range. Format: (IP address/ sub
mask)
Leave Proxy Enable:
Enable IGMP Leave Proxy. This feature can be used to avoid forwarding unnecessary
leave messages to the router side.
Proxy Enabled :
Enable IGMP Proxy. This feature can be used to avoid forwarding unnecessary join
and leave messages to the router side.
Port :
It shows the physical Port index of switch.
Router Port :
Specify which ports act as router ports. A router port is a port on the Ethernet
switch that leads towards the Layer 3 multicast device or IGMP querier.
If an aggregation member port is selected as a router port, the whole aggregation
will act as a router port.
Fast Leave :
Enable the fast leave on the port.
Throttling :
Enable to limit the number of multicast groups to which a switch port can belong.
2-12.1.2 VLAN Configuration
The section describes the VLAN configuration setting process integrated with IGMP
144
Snooping function. For Each setting page shows up to 99 entries from the VLAN table,
default being 20, selected through the "entries per page" input field. When first visited,
the web page will show the first 20 entries from the beginning of the VLAN Table. The
first displayed will be the one with the lowest VLAN ID found in the VLAN Table. The
"VLAN" input fields allow the user to select the starting point in the VLAN Table.
Clicking the button will update the displayed table starting from that or the next
closest VLAN Table match.
Web Interface
To configure the IGMP Snooping VLAN Configuration in the web interface:
1. Click Configuration, IPMC, IGMP Snooping, VLAN Configuration
2. Evoke to select enable or disable Snooping, IGMP Querier. Specify the parameters
in the blank field.
3. Click the refresh to update the data or click << or >> to display previous entry or
next entry.
4. Click the save to save the setting
5. If you want to cancel the setting then you need to click the Reset button. It will
revert to previously saved values
Figure 2-12.1.2: The IGMP Snooping VLAN Configuration.
145
Parameter description:
Delete :
Check to delete the entry. The designated entry will be deleted during the next
save.
VLAN ID :
It displays the VLAN ID of the entry.
IGMP Snooping Enabled :
Enable the per-VLAN IGMP Snooping. Only up to 32 VLANs can be selected. .
Querier Election :
Enable to join IGMP Querier election in the VLAN. Disable to act as an IGMP
Non-Querier.
Querier Address :
Define the IPv4 address as source address used in IP header for IGMP Querier
election.
When the Querier address is not set, system uses IPv4 management address of the
IP interface associated with this VLAN.
When the IPv4 management address is not set, system uses the first available IPv4
management address.
Otherwise, system uses a pre-defined value. By default, this value will be 192.0.2.1.
Compatibility :
Compatibility is maintained by hosts and routers taking appropriate actions
depending on the versions of IGMP operating on hosts and routers within a
146
network. The allowed selection is IGMP-Auto, Forced IGMPv1, Forced IGMPv2,
Forced IGMPv3, default compatibility value is IGMP-Auto.
PRI :
Priority of Interface.
It indicates the IGMP control frame priority level generated by the system. These
values can be used to prioritize different classes of traffic.
The allowed range is 0 (best effort) to 7 (highest), default interface priority value is
0.
Rv :
Robustness Variable. The Robustness Variable allows tuning for the expected packet
loss on a network. The allowed range is 1 to 255; default robustness variable value is
2.
QI :
Query Interval. The Query Interval is the interval between General Queries sent by
the Querier. The allowed range is 1 to 31744 seconds; default query interval is 125
seconds.
QRI :
Query Response Interval. The Max Response Time used to calculate the Max Resp
Code inserted into the periodic General Queries. The allowed range is 0 to 31744 in
tenths of seconds; default query response interval is 100 in tenths of seconds (10
seconds).
LLQI (LMQI for IGMP) :
Last Member Query Interval. The Last Member Query Time is the time value
represented by the Last Member Query Interval, multiplied by the Last Member
Query Count. The allowed range is 0 to 31744 in tenths of seconds; default last
member query interval is 10 in tenths of seconds (1 second).
URI :
Unsolicited Report Interval. The Unsolicited Report Interval is the time between
repetitions of a host's initial report of membership in a group. The allowed range is
0 to 31744 seconds, default unsolicited report interval is 1 second. .
Buttons :
147
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
Upper right icon (Refresh, |<<, >>) :
You can click them Refreshes the displayed table starting from the "VLAN" input
fields. Or click “|<<” to update the table starting from the first entry in the VLAN
table, i.e. the entry with the lowest VLAN ID. Others click “>> “ to update the table,
starting with the entry after the last entry currently displayed.
2-12.1.3 Port Filtering Profile
The section describes how to set the IGMP Port Group Filtering? With the IGMP
filtering feature, a user can exert this type of control. In some network Application
environments, as like the metropolitan or multiple-dwelling unit (MDU) installations, a
user might want to control the multicast groups to which a user on a switch port can
belong. It allows the user to control the distribution of multicast services, such as IP/TV,
based on some type of subscription or service plan.
With this feature, you can filter multicast joins on a per-port basis by configuring IP
multicast profiles and associating them with individual switch ports. An IGMP profile
can contain one or more multicast groups and specifies whether access to the group is
permitted or denied. If an IGMP profile denying access to a multicast group is applied
to a switch port, the IGMP join report requesting the stream of IP multicast traffic is
dropped, and the port is not allowed to receive IP multicast traffic from that group. If
the filtering action permits access to the multicast group, the IGMP report from the
port is forwarded for normal processing.
IGMP filtering controls only IGMP membership join reports and has no relationship to
the function that directs the forwarding of IP multicast traffic.
Web Interface
To configure the IGMP Snooping Port Group Configuration in the web interface:
1. Click Configuration, IPMC, IGMP Snooping, Port Group Filtering
2. Click Add new Filtering Group
3. Scroll the Port to enable the Port Group Filtering. Specify the Filtering Groups in
148
the blank field.
4. Click the save to save the setting
5. If you want to cancel the setting then you need to click the Reset button. It will
revert to previously saved values
Figure 2-12.1.3: The IGMP Snooping Port Group Filtering Profile.
Parameter description:
Port :
The logical port for the settings.
Filtering Profile :
Select the IPMC Profile as the filtering condition for the specific port. Summary
about the designated profile will be shown by clicking the view button.
Profile Management Button :
You can inspect the rules of the designated profile by using the following button:
: List the rules associated with the designated profile.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
149
2-12.2 MLD Snooping
Curiously enough, a network node that acts as a source of IPv6 multicast traffic is only
an indirect participant in MLD snooping—it just provides multicast traffic, and MLD
doesn’t interact with it. (Note, however, that in an application like desktop
conferencing a network node may act as both a source and an MLD host; but MLD
interacts with that node only in its role as an MLD host.)
A source node creates multicast traffic by sending packets to a multicast address. In
IPv6, addresses with the first eight bits set (that is, “FF” as the first two characters of the
address) are multicast addresses, and any node that listens to such an address will
receive the traffic sent to that address. Application software running on the source and
destination systems cooperates to determine what multicast address to use. (Note that
this is a function of the application software, not of MLD.)
When MLD snooping is enabled on a VLAN, the switch acts to minimize unnecessary
multicast traffic. If the switch receives multicast traffic destined for a given multicast
address, it forwards that traffic only to ports on the VLAN that have MLD hosts for that
address. It drops that traffic for ports on the VLAN that have no MLD hosts
2-12.2.1 Basic Configuration
The section will let you understand how to configure the MLD Snooping basic
configuration and the parameters.
Web Interface
150
To configure the MLD Snooping Configuration in the web interface:
1. Click Configuration, MLD Snooping, Basic Configuration
2. Evoke to enable or disable the Global configuration parameters. Evoke the port to
join Router port and Fast Leave.
3. Scroll to select the Throtting mode with unlimited or 1 to 10
4. Click the save to save the setting
5. If you want to cancel the setting then you need to click the Reset button. It will
revert to previously saved values
151
Figure 2-12.2.1: The MLD Snooping Basic Configuration.
Parameter description:
Snooping Enabled :
Enable the Global MLD Snooping.
Unregistered IPMCv6 Flooding enabled :
Enable unregistered IPMCv6 traffic flooding.
The flooding control takes effect only when MLD Snooping is enabled.
When MLD Snooping is disabled, unregistered IPMCv6 traffic flooding is always
active in spite of this setting.
MLD SSM Range :
152
SSM (Source-Specific Multicast) Range allows the SSM-aware hosts and routers run
the SSM service model for the groups in the address (Using IPv6 Address) range.
Leave Proxy Enabled :
Enable MLD Leave Proxy. This feature can be used to avoid forwarding unnecessary
leave messages to the router side.
Proxy Enabled :
Enable MLD Proxy. This feature can be used to avoid forwarding unnecessary join
and leave messages to the router side.
Fast Leave :
To evoke to enable the fast leave on the port.
Router Port :
Specify which ports act as router ports. A router port is a port on the Ethernet
switch that leads towards the Layer 3 multicast device or MLD querier. If an
aggregation member port is selected as a router port, the whole aggregation will
act as a router port.
Throttling :
Enable to limit the number of multicast groups to which a switch port can belong.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
2-12.2.2 VLAN Configuration
When MLD snooping is enabled on a VLAN, the switch acts to minimize unnecessary
multicast traffic. If the switch receives multicast traffic destined for a given multicast
address, it forwards that traffic only to ports on the VLAN that have MLD hosts for that
address. It drops that traffic for ports on the VLAN that have no MLD hosts
The will use the last entry of the currently displayed entry as a basis for the next
lookup. When the end is reached the text "No more entries" is shown in the displayed
table. Use the button to start over.
153
Web Interface
To configure the MLD Snooping VLAN Configuration in the web interface:
1. Click Configuration, IPMC, MLD Snooping, VLAN Configuration
2. Specify the VLAN ID with entries per page.
3. Click “Refresh” to refresh an entry of the MLD Snooping VLAN Configuration
Information.
4. Click “<< or >> “to move to previous or next entry.
Figure 2-12.2.2: The MLD Snooping VLAN Configuration.
Parameter description:
Delete :
Check to delete the entry. The designated entry will be deleted during the next
save.
VLAN ID :
It displays the VLAN ID of the entry.
IGMP Snooping Enabled :
Enable the per-VLAN IGMP Snooping. Only up to 32 VLANs can be selected. .
Querier Election :
Enable to join IGMP Querier election in the VLAN. Disable to act as an IGMP
Non-Querier.
154
Querier Address :
Define the IPv4 address as source address used in IP header for IGMP Querier
election.
When the Querier address is not set, system uses IPv4 management address of the
IP interface associated with this VLAN.
When the IPv4 management address is not set, system uses the first available IPv4
management address.
Otherwise, system uses a pre-defined value. By default, this value will be 192.0.2.1.
Compatibility :
Compatibility is maintained by hosts and routers taking appropriate actions
depending on the versions of IGMP operating on hosts and routers within a
network. The allowed selection is IGMP-Auto, Forced IGMPv1, Forced IGMPv2,
Forced IGMPv3, default compatibility value is IGMP-Auto.
PRI :
Priority of Interface.
It indicates the IGMP control frame priority level generated by the system. These
values can be used to prioritize different classes of traffic.
The allowed range is 0 (best effort) to 7 (highest), default interface priority value is
0.
Rv :
Robustness Variable. The Robustness Variable allows tuning for the expected packet
loss on a network. The allowed range is 1 to 255; default robustness variable value is
2.
QI :
Query Interval. The Query Interval is the interval between General Queries sent by
the Querier. The allowed range is 1 to 31744 seconds; default query interval is 125
seconds.
QRI :
Query Response Interval. The Max Response Time used to calculate the Max Resp
Code inserted into the periodic General Queries. The allowed range is 0 to 31744 in
155
tenths of seconds; default query response interval is 100 in tenths of seconds (10
seconds).
LLQI (LMQI for IGMP) :
Last Member Query Interval. The Last Member Query Time is the time value
represented by the Last Member Query Interval, multiplied by the Last Member
Query Count. The allowed range is 0 to 31744 in tenths of seconds; default last
member query interval is 10 in tenths of seconds (1 second).
URI :
Unsolicited Report Interval. The Unsolicited Report Interval is the time between
repetitions of a host's initial report of membership in a group. The allowed range is
0 to 31744 seconds, default unsolicited report interval is 1 second. .
Buttons :
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
Upper right icon (Refresh, |<<, >>) :
You can click them Refreshes the displayed table starting from the "VLAN" input
fields. Or click “|<<” to update the table starting from the first entry in the VLAN
table, i.e. the entry with the lowest VLAN ID. Others click “>> “ to update the table,
starting with the entry after the last entry currently displayed.
2-12.2.3 Port Group Filtering
The section describes that you could to set the Port Group Filtering in the MLD
Snooping function. On the UI that you could add new filtering group and safety policy.
Web Interface
To configure the MLD Snooping Port Group Configuration in the web interface:
1. Click Configuration, IPMC, MLD Snooping, Port Group Filtering Configuration
2. Click the Add new Filtering Group
3. Specify the Filtering Groups with entries per page.
156
4. Click the Apply to save the setting
5. If you want to cancel the setting then you need to click the Reset button. It will
revert to previously saved values
Figure 2-12.2.3: The MLD Snooping Port Group Filtering Configuration
Parameter description:
Port :
The logical port for the settings.
Filtering Profile :
Select the IPMC Profile as the filtering condition for the specific port. Summary
about the designated profile will be shown by clicking the view button.
Profile Management Button :
You can inspect the rules of the designated profile by using the following button:
: List the rules associated with the designated profile.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
157
2-13 LLDP
The switch supports the LLDP. For current information on your switch model, The
Link Layer Discovery Protocol (LLDP) provides a standards-based method for enabling
switches to advertise themselves to adjacent devices and to learn about adjacent LLDP
devices. The Link Layer Discovery Protocol (LLDP) is a vendor-neutral Link Layer
protocol in the Internet Protocol Suite used by network devices for advertising their
identity, capabilities, and neighbors on a IEEE 802 local area network, principally wired
Ethernet. The protocol is formally referred to by the IEEE as Station and Media Access
Control Connectivity Discovery specified in standards document IEEE 802.1AB.
2-13.1 LLDP
You can per port to do the LLDP configuration and the detail parameters, the settings
will take effect immediately. This page allows the user to inspect and configure the
current LLDP port settings.
Web Interface
To configure LLDP:
1. Click LLDP configuration
2. Modify LLDP timing parameters
3. Set the required mode for transmitting or receiving LLDP messages
4. Specify the information to include in the TLV field of advertised messages
5. Click Apply
Figure 2-13.1: The LLDP Configuration
158
Parameter description:
LLDP Parameters
Tx Interval :
The switch periodically transmits LLDP frames to its neighbours for having the
network discovery information up-to-date. The interval between each LLDP frame is
determined by the Tx Interval value. Valid values are restricted to 5 - 32768 seconds.
Tx Hold :
Each LLDP frame contains information about how long the information in the LLDP
frame shall be considered valid. The LLDP information valid period is set to Tx Hold
multiplied by Tx Interval seconds. Valid values are restricted to 2 - 10 times.
Tx Delay :
If some configuration is changed (e.g. the IP address) a new LLDP frame is
transmitted, but the time between the LLDP frames will always be at least the value
of Tx Delay seconds. Tx Delay cannot be larger than 1/4 of the Tx Interval value. Valid
values are restricted to 1 - 8192 seconds.
Tx Reinit :
When a port is disabled, LLDP is disabled or the switch is rebooted, an LLDP
shutdown frame is transmitted to the neighboring units, signaling that the LLDP
information isn't valid anymore. Tx Reinit controls the amount of seconds between
159
the shutdown frame and a new LLDP initialization. Valid values are restricted to 1 -
10 seconds.
LLDP Port Configuration
The LLDP port settings relate to the currently selected, as reflected by the page header.
Port :
The switch port number of the logical LLDP port.
Mode :
Select LLDP mode.
Rx only The switch will not send out LLDP information, but LLDP information from
neighbor units is analyzed.
Tx only The switch will drop LLDP information received from neighbors, but will
send out LLDP information.
Disabled The switch will not send out LLDP information, and will drop LLDP
information received from neighbors.
Enabled the switch will send out LLDP information, and will analyze LLDP
information received from neighbors.
CDP Aware :
Select CDP awareness.
The CDP operation is restricted to decoding incoming CDP frames (The switch
doesn't transmit CDP frames). CDP frames are only decoded if LLDP on the port is
enabled.
Only CDP TLVs that can be mapped to a corresponding field in the LLDP neighbors’
table are decoded. All other TLVs are discarded (Unrecognized CDP TLVs and
discarded CDP frames are not shown in the LLDP statistics.). CDP TLVs are mapped
onto LLDP neighbors’ table as shown below.
CDP TLV "Device ID" is mapped to the LLDP "Chassis ID" field.
CDP TLV "Address" is mapped to the LLDP "Management Address" field. The CDP
address TLV can contain multiple addresses, but only the first address is shown in
the LLDP neighbors’ table.
160
CDP TLV "Port ID" is mapped to the LLDP "Port ID" field.
CDP TLV "Version and Platform" is mapped to the LLDP "System Description" field.
Both the CDP and LLDP support "system capabilities", but the CDP capabilities cover
capabilities that are not part of the LLDP. These capabilities are shown as "others" in
the LLDP neighbors’ table.
If all ports have CDP awareness disabled the switch forwards CDP frames received
from neighbor devices. If at least one port has CDP awareness enabled all CDP
frames are terminated by the switch.
NOTE: When CDP awareness on a port is disabled the CDP
information isn't removed immediately, but gets when the hold
time is exceeded.
Port Descr :
Optional TLV: When checked the "port description" is included in LLDP information
transmitted.
Sys Name :
Optional TLV: When checked the "system name" is included in LLDP information
transmitted.
Sys Descr :
Optional TLV: When checked the "system description" is included in LLDP
information transmitted.
Sys Capa :
Optional TLV: When checked the "system capability" is included in LLDP information
transmitted.
Mgmt Addr :
Optional TLV: When checked the "management address" is included in LLDP
information transmitted.
Buttons:
Apply – Click to save changes.
161
Reset- Click to undo any changes made locally and revert to previously saved
values.
162
2-13.2 LLDP-MED
Media Endpoint Discovery is an enhancement of LLDP, known as LLDP-MED that
provides the following facilities:
Auto-discovery of LAN policies (such as VLAN, Layer 2 Priority and Differentiated
services (Diffserv) settings) enabling plug and play networking.
Device location discovery to allow creation of location databases and, in the case of
Voice over Internet Protocol (VoIP), Enhanced 911 services.
Extended and automated power management of Power over Ethernet (PoE) end
points.
Inventory management, allowing network administrators to track their network
devices, and determine their characteristics (manufacturer, software and hardware
versions, and serial or asset number).
This page allows you to configure the LLDP-MED. This function applies to VoIP devices
which support LLDP-MED.
Web Interface
To configure LLDP-MED:
1. Click LLDP-MED Configuration
2. Modify Fast start repeat count parameter, default is 4
3. Modify Coordinates Location parameters
4. Fill Civic Address Location parameters
5. Add new policy
6. Click Apply, will show following Policy Port Configuration
7. Select Policy ID for each port
8. Click Apply
Figure 2-13.2: The LLDP-MED Configuration
163
Parameter description:
Fast start repeat count
164
Rapid startup and Emergency Call Service Location Identification Discovery of
endpoints is a critically important aspect of VoIP systems in general. In addition, it is
best to advertise only those pieces of information which are specifically relevant to
particular endpoint types (for example only advertise the voice network policy to
permitted voice-capable devices), both in order to conserve the limited LLDPU space
and to reduce security and system integrity issues that can come with inappropriate
knowledge of the network policy.
With this in mind LLDP-MED defines an LLDP-MED Fast Start interaction between the
protocol and the application layers on top of the protocol, in order to achieve these
related properties. Initially, a Network Connectivity Device will only transmit LLDP TLVs
in an LLDPDU. Only after an LLDP-MED Endpoint Device is detected, will an LLDP-MED
capable Network Connectivity Device start to advertise LLDP-MED TLVs in outgoing
LLDPDUs on the associated port. The LLDP-MED application will temporarily speed up
the transmission of the LLDPDU to start within a second, when a new LLDP-MED
neighbour has been detected in order share LLDP-MED information as fast as possible
to new neighbours.
Because there is a risk of an LLDP frame being lost during transmission between
neighbours, it is recommended to repeat the fast start transmission multiple times to
increase the possibility of the neighbours receiving the LLDP frame. With Fast start
repeat count it is possible to specify the number of times the fast start transmission
would be repeated. The recommended value is 4 times, given that 4 LLDP frames with
a 1 second interval will be transmitted, when an LLDP frame with new information is
received.
It should be noted that LLDP-MED and the LLDP-MED Fast Start mechanism is only
intended to run on links between LLDP-MED Network Connectivity Devices and
Endpoint Devices, and as such does not apply to links between LAN infrastructure
elements, including Network Connectivity Devices, or other types of links.
Coordinates Location
Latitude :
Latitude SHOULD be normalized to within 0-90 degrees with a maximum of 4 digits.
It is possible to specify the direction to either North of the equator or South of the
equator.
Longitude :
165
Longitude SHOULD be normalized to within 0-180 degrees with a maximum of 4
digits.
It is possible to specify the direction to either East of the prime meridian or West of
the prime meridian.
Altitude :
Altitude SHOULD be normalized to within -32767 to 32767 with a maximum of 4
digits.
It is possible to select between two altitude types (floors or meters).
Meters: Representing meters of Altitude defined by the vertical datum specified.
Floors: Representing altitude in a form more relevant in buildings which have
different floor-to-floor dimensions. An altitude = 0.0 is meaningful even outside a
building, and represents ground level at the given latitude and longitude. Inside a
building, 0.0 represents the floor level associated with ground level at the main
entrance.
Map Datum :
The Map Datum is used for the coordinates given in these options:
WGS84: (Geographical 3D) - World Geodesic System 1984, CRS Code 4327, and
Prime Meridian Name: Greenwich.
NAD83/NAVD88: North American Datum 1983, CRS Code 4269, Prime Meridian
Name: Greenwich; the associated vertical datum is the North American Vertical
Datum of 1988 (NAVD88). This datum pair is to be used when referencing locations
on land, not near tidal water (which would use Datum = NAD83/MLLW).
NAD83/MLLW: North American Datum 1983, CRS Code 4269, Prime Meridian
Name: Greenwich; the associated vertical datum is Mean Lower Low Water (MLLW).
This datum pair is to be used when referencing locations on water/sea/ocean.
Civic Address Location
IETF Geopriv Civic Address based Location Configuration Information (Civic
Address LCI).
Country code :
The two-letter ISO 3166 country code in capital ASCII letters - Example: DK, DE or
166
US.
State :
National subdivisions (state, canton, region, province, prefecture).
County :
County, parish, gun (Japan), district.
City :
City, township, shi (Japan) - Example: Copenhagen.
City district :
City division, borough, city district, ward, chou (Japan).
Block (Neighbourhood) :
Neighbourhood, block.
Street :
Street - Example: Poppelvej.
Leading street direction :
Leading street direction - Example: N.
Trailing street suffix :
Trailing street suffix - Example: SW.
Street suffix :
Street suffix - Example: Ave, Platz.
House no. :
House number - Example: 21.
House no. suffix :
House number suffix - Example: A, 1/2.
Landmark :
Landmark or vanity address - Example: Columbia University.
Additional location info :
167
Additional location info - Example: South Wing.
Name :
Name (residence and office occupant) - Example: Flemming Jahn.
Zip code :
Postal/zip code - Example: 2791.
Building :
Building (structure) - Example: Low Library.
Apartment :
Unit (Apartment, suite) - Example: Apt 42.
Floor :
Floor - Example: 4.
Room no. :
Room number - Example: 450F.
Place type :
Place type - Example: Office.
Postal community name :
Postal community name - Example: Leonia.
P.O. Box :
Post office box (P.O. BOX) - Example: 12345.
Additional code :
Additional code - Example: 1320300003.
Emergency Call Service:
Emergency Call Service (e.g. E911 and others), such as defined by TIA or NENA.
Emergency Call Service :
Emergency Call Service ELIN identifier data format is defined to carry the ELIN
identifier as used during emergency call setup to a traditional CAMA or ISDN
168
trunk-based PSAP. This format consists of a numerical digit string, corresponding to
the ELIN to be used for emergency calling.
Policies
Network Policy Discovery enables the efficient discovery and diagnosis of mismatch
issues with the VLAN configuration, along with the associated Layer 2 and Layer 3
attributes, which apply for a set of specific protocol applications on that port.
Improper network policy configurations are a very significant issue in VoIP
environments that frequently result in voice quality degradation or loss of service.
Policies are only intended for use with applications that have specific 'real-time'
network policy requirements, such as interactive voice and/or video services.
The network policy attributes advertised are:
1. Layer 2 VLAN ID (IEEE 802.1Q-2003)
2. Layer 2 priority value (IEEE 802.1D-2004)
3. Layer 3 Diffserv code point (DSCP) value (IETF RFC 2474)
This network policy is potentially advertised and associated with multiple sets of
application types supported on a given port. The application types specifically
addressed are:
1. Voice
2. Guest Voice
3. Softphone Voice
4. Video Conferencing
5. Streaming Video
6. Control / Signalling (conditionally support a separate network policy for the media
types above)
A large network may support multiple VoIP policies across the entire organization, and
different policies per application type. LLDP-MED allows multiple policies to be
advertised per port, each corresponding to a different application type. Different ports
on the same Network Connectivity Device may advertise different sets of policies,
based on the authenticated user identity or port configuration.
169
It should be noted that LLDP-MED is not intended to run on links other than between
Network Connectivity Devices and Endpoints, and therefore does not need to
advertise the multitude of network policies that frequently run on an aggregated link
interior to the LAN.
Delete :
Check to delete the policy. It will be deleted during the next save.
Policy ID :
ID for the policy. This is auto generated and shall be used when selecting the polices
that shall be mapped to the specific ports.
Application Type :
Intended use of the application types:
1. Voice - for use by dedicated IP Telephony handsets and other similar appliances
supporting interactive voice services. These devices are typically deployed on a
separate VLAN for ease of deployment and enhanced security by isolation from
data applications.
2. Voice Signalling (conditional) - for use in network topologies that require a
different policy for the voice signalling than for the voice media. This application
type should not be advertised if all the same network policies apply as those
advertised in the Voice application policy.
3. Guest Voice - support a separate 'limited feature-set' voice service for guest users
and visitors with their own IP Telephony handsets and other similar appliances
supporting interactive voice services.
4. Guest Voice Signalling (conditional) - for use in network topologies that require a
different policy for the guest voice signalling than for the guest voice media. This
application type should not be advertised if all the same network policies apply as
those advertised in the Guest Voice application policy.
5. Softphone Voice - for use by softphone applications on typical data centric
devices, such as PCs or laptops. This class of endpoints frequently does not support
multiple VLANs, if at all, and are typically configured to use an 'untagged' VLAN or a
single 'tagged' data specific VLAN. When a network policy is defined for use with an
'untagged' VLAN (see Tagged flag below), then the L2 priority field is ignored and
only the DSCP value has relevance.
170
6. Video Conferencing - for use by dedicated Video Conferencing equipment and
other similar appliances supporting real-time interactive video/audio services.
7. Streaming Video - for use by broadcast or multicast based video content
distribution and other similar applications supporting streaming video services that
require specific network policy treatment. Video applications relying on TCP with
buffering would not be an intended use of this application type.
8. Video Signalling (conditional) - for use in network topologies that require a
separate policy for the video signalling than for the video media. This application
type should not be advertised if all the same network policies apply as those
advertised in the Video Conferencing application policy.
Tag :
Tag indicating whether the specified application type is using a 'tagged' or an
'untagged' VLAN.
Untagged indicates that the device is using an untagged frame format and as such
does not include a tag header as defined by IEEE 802.1Q-2003. In this case, both the
VLAN ID and the Layer 2 priority fields are ignored and only the DSCP value has
relevance.
Tagged indicates that the device is using the IEEE 802.1Q tagged frame format, and
that both the VLAN ID and the Layer 2 priority values are being used, as well as the
DSCP value. The tagged format includes an additional field, known as the tag
header. The tagged frame format also includes priority tagged frames as defined by
IEEE 802.1Q-2003.
VLAN ID :
VLAN identifier (VID) for the port as defined in IEEE 802.1Q-2003.
L2 Priority :
L2 Priority is the Layer 2 priority to be used for the specified application type. L2
Priority may specify one of eight priority levels (0 through 7), as defined by IEEE
802.1D-2004. A value of 0 represents use of the default priority as defined in IEEE
802.1D-2004.
DSCP :
DSCP value to be used to provide Diffserv node behaviour for the specified
application type as defined in IETF RFC 2474. DSCP may contain one of 64 code
171
point values (0 through 63). A value of 0 represents use of the default DSCP value as
defined in RFC 2475.
Adding a new policy :
Click to add a new policy. Specify the Application type, Tag, VLAN ID, L2 Priority and
DSCP for the new policy. Click "Save".
Port Policies Configuration :
Every port may advertise a unique set of network policies or different attributes for
the same network policies, based on the authenticated user identity or port
configuration.
Port :
The port number to which the configuration applies.
Policy Id :
The set of policies that shall apply to a given port. The set of policies is selected by
check marking the checkboxes that corresponds to the policies.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
2-14 PoE
PoE is an acronym for Power over Ethernet.
Power over Ethernet is used to transmit electrical power, to remote devices over
standard Ethernet cable. It could for example be used for powering IP telephones,
wireless LAN access points and other equipment, where it would be difficult or
expensive to connect the equipment to main power supply.
The PoE detect function is follow the table
Stages of Powering up a PoE Link
Stage
Action
Volts specified
[V]
172
802.3af
802.3at
Detection
PSE detects if the PD has the correct
signature resistance of 19–26.5 kΩ
2.7-10.1
Classification
PSE detects resistor indicating power
range
14.5-20.5
Mark 1
Signals PSE is 802.3at capable. PD
presents a 0.25–4 mA load.
─
7-10
Class 2
PSE outputs classification voltage
again to indicate 802.3at capability
─
14.5-20.5
Mark 2
Signals PSE is 802.3at capable. PD
presents a 0.25–4 mA load.
─
7-10
Startup
Startup voltage
>42
>42
Normal
operation
Supply power to device
37-45
42.5-57
Power levels available
Class
Usage
Power
range
[Watt]
Class description
0
Default
15.4
Classification
unimplemented
1
Optional
4
Very Low power
2
Optional
7
Low power
3
Optional
15.4
Mid power
4
Valid for 802.3at (Type
2) devices, not allowed
for 802.3af devices
30
High power
2- 14.1 Configuration
This page allows the user to inspect and configure the current PoE port settings and
show all PoE Supply W.
Web Interface
To configure Power over Ethernet in the web interface:
1. Click configuration, PoE, and configuration
173
2. Specify the Reserved Power determined and Power Management ode. Specify the
PoE or PoE+ and Priority.
3. Click Apply.
Figure 2-14.1: The PoE Configuration
Parameter description:
Power Supply Configuration
Reserved Power determined by :
There are three modes for configuring how the ports/PDs may reserve power.
1. Allocated mode: In this mode the user allocates the amount of power that each
port may reserve. The allocated/reserved power for each port/PD is specified in the
Maximum Power fields.
2. Class mode: In this mode each port automatically determines how much power
to reserve according to the class the connected PD belongs to, and reserves the
power accordingly. Four different port classes exist and one for 4, 7, 15.4 or 30
174
Watts. In this mode the Maximum Power fields have no effect.
3. LLDP-MED mode: This mode is similar to the Class mode expect that each port
determine the amount power it reserves by exchanging PoE information using the
LLDP protocol and reserves power accordingly. If no LLDP information is available
for a port, the port will reserve power using the class mode In this mode the
Maximum Power fields have no effect for all modes: If a port uses more power than
the reserved power for the port, the port is shut down.
Power Management Mode :
There are 2 modes for configuring when to shut down the ports:
1. Actual Consumption: In this mode the ports are shut down when the actual
power consumption for all ports exceeds the amount of power that the power
supply can deliver or if the actual power consumption for a given port exceeds the
reserved power for that port. The ports are shut down according to the ports
priority. If two ports have the same priority the port with the highest port number is
shut down.
2. Reserved Power: In this mode the ports are shut down when total reserved
powered exceeds the amount of power that the power supply can deliver. In this
mode the port power is not turned on if the PD requests more power than available
from the power supply.
Primary and Backup Power Source :
Some switches support having two PoE power supplies. One is used as primary
power source, and one as backup power source. If the switch doesn't support
backup power supply only the primary power supply settings will be shown. In case
that the primary power source fails the backup power source will take over. For
being able to determine the amount of power the PD may use, it must be defined
what amount of power the primary and backup power sources can deliver.
Valid values are in the range 0 to 2000 Watts.
Port :
This is the logical port number for this row.
Ports that are not PoE-capable are grayed out and thus impossible to configure PoE
for.
PoE Mode :
175
The PoE Mode represents the PoE operating mode for the port.
Disabled: PoE disabled for the port.
PoE : Enables PoE IEEE 802.3af (Class 4 PDs limited to 15.4W)
PoE+ : Enables PoE+ IEEE 802.3at (Class 4 PDs limited to 30W)
Priority :
The Priority represents the ports priority. There are three levels of power priority
named Low, High and Critical.
The priority is used in the case where the remote devices requires more power than
the power supply can deliver. In this case the port with the lowest priority will be
turn off starting from the port with the highest port number.
Maximum Power :
The Maximum Power value contains a numerical value that indicates the maximum
power in watts that can be delivered to a remote device.
The maximum allowed value is 30 W.
176
2- 14.2 Power Delay
This page allows the user to setting the delay time of power providing after device
rebooted.
Web Interface
To Display Power over Ethernet Status in the web interface:
1. Click Configuration, PoE, and Power delay.
2. Enable the port to the power device.
3. Specify the power providing delay time when reboot.
4. Click Apply to apply the change.
Figure 2-14.2: The PoE Power Delay
Parameter description:
Power Supply Configuration
Port :
This is the logical port number for this row.
Delay Mode :
177
Turn on / off the power delay function.
Enabled: Enable POE Power Delay.
Disabled: Disable POE Power Delay.
Delay Time(0~300sec) :
When rebooting, the PoE port will start to provide power to the PD when it out of
delay time. Default: 0, range: 0-300 sec.
178
2- 14.3 Schedule Profile
This page allows the user to make a perfect schedule of PoE power supply. PoE
Scheduling not only makes PoE management easier but also saves more energy
Web Interface
To Display Power Over Ethernet Scheduling in the web interface:
1. Click Configuration, PoE, and Scheduling.
2. Select the local port and enable.
3. Select time and day to supply power.
4. Click Apply to apply the change.
Figure 2-13.3: The Schedule Profile
Parameter description:
179
Power Supply Configuration
Port :
This is the logical port number for this row.
Status :
PoE Scheduling Status.
Enabled: Enable POE Scheduling.
Disabled: Disable POE Scheduling.
Hour :
The time of PoE port provide power of a day.
2- 14.4 Auto Checking
This page allows the user to specify the auto detection parameters to check the linking
status between PoE ports and PDs. When it detected the fail connect, will reboot
remote PD automatically.
Web Interface
To Display Power over Ethernet Auto Checking in the web interface:
1. Click Configuration, PoE, and Auto checking.
2. Enable the Ping Check function.
3. Specify the PD’s IP address, checking interval, retry time, failure action and reboot
time.
4. Click Apply to apply the change.
Figure 2-14.4: The PoE Scheduling
180
Parameter description:
Power Supply Configuration
Ping Check :
Enable Ping Check function can detects the connection between PoE port and
power device. Disable will turn off the detection.
Port :
This is the logical port number for this row.
Ping IP Address :
The PD's IP Address the system should ping.
Interval Time(sec) :
Device will send checking message to PD each interval time. Default: 30, range:
10-120 sec.
Retry Time :
When PoE port can't ping the PD, it will retry to send detection again. When the
third time, it will trigger failure action. Default: 3, range: 1-5.
Failure Log :
Failure loggings counter.
181
Failure Action :
The action when the third fail detection.
Nothing: Keep Ping the remote PD but does nothing further.
Reboot Remote PD: Cut off the power of the PoE port, make PD rebooted.
Reboot time(sec) :
When PD has been rebooted, the PoE port restored power after the specified time.
Default: 15, range: 3-120 sec.
2- 14.5 Chip Reset Schedule
This page allows user to schedule when to reset PoE chip
Web Interface
To Display Power over Ethernet Chip Reset Schedule in the web interface:
1. Click Configuration, PoE, and Chip Reset Schedule.
2. Evoke to enable or disable the Mode.
3. Click Apply to apply the change.
Figure 2-14.5: The Chip Reset Schedule
Parameter description:
Power Supply Configuration
Mode
Indicates the chip reset scheduling mode operation. Possible modes are:
Enabled: Enable PoE chip reset.
182
Disabled: Disable PoE chip reset.
Week Day
The day to reset PoE chip.
PoE Chip Reset Time
The time to reset PoE chip.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
2-15 EPS
The Ethernet (Linear) Protection Switch instances are configured here.
Web Interface
To configure the EPS parameters in the web interface:
1. Click Configuration and EPS.
2. Specify the Ethernet Protection Switching parameters.
3. Click Apply to apply the change.
Figure 2-15: The Ethernet Protection Switching
Parameter description:
183
Power Supply Configuration
Delete
This box is used to mark an EPS for deletion in next save operation.
EPS ID
The ID of the EPS. Click on the ID of an EPS to enter the configuration page. The range is
1-100.
Domain
Port: This will create an EPS in the Port Domain. 'W/P Flow' is a Port.
Architecture
Port: This will create a 1+1 EPS.
Port: This will create a 1:1 EPS.
W Flow
The working flow for the EPS - See 'Domain'.
P Flow
The protecting flow for the EPS - See 'Domain'.
W SF MEP
The working Signal Fail reporting MEP.
P SF MEP
The protecting Signal Fail reporting MEP.
APS MEP
The APS PDU handling MEP.
Alarm
There is an active alarm on the EPS.
Buttons:
Apply – Click to save changes.
184
Reset- Click to undo any changes made locally and revert to previously saved
values.
185
2-16 MEP
The Maintenance Entity Point instances are configured here.
Web Interface
To configure the MEP parameters in the web interface:
1. Click Configuration and MEP.
2. Specify the Maintenance Entity Point parameters.
3. Click Apply to apply the change.
Figure 2-16: The Maintenance Entity Point
Parameter description:
Power Supply Configuration
Delete
This box is used to mark a MEP for deletion in next Save operation.
Instance
The ID of the MEP. Click on the ID of a MEP to enter the configuration page. The range is
from 1 through 100.
Domain
Port: This is a MEP in the Port Domain.
EVC: This is a MEP in the EVC Domain. 'Flow Instance' is an EVC. The EVC must be created
VLAN: This is a MEP in the VLAN Domain. 'Flow Instance' is a VLAN. In case of Up-MEP
the VLAN must be created
Mode
MEP: This is a Maintenance Entity End Point.
MIP: This is a Maintenance Entity Intermediate Point.
186
Direction
Down: This is a Down MEP - monitoring ingress OAM and traffic on 'Residence Port'.
Up: This is a Up MEP - monitoring egress OAM and traffic on 'Residence Port'.
Residence Port
The port where MEP is monitoring - see 'Direction'. For a EVC MEP the port must be a
port in the EVC. For a VLAN MEP the port must be a VLAN member.
Level
The MEG level of this MEP.
Flow Instance
The MEP is related to this flow - See 'Domain'. This is not relevant and not shown in case
of Port MEP.
Tagged VID
Port MEP: An outer C/S-tag (depending on VLAN Port Type) is added with this VID.
Entering '0' means no TAG added.
EVC MEP: This is not used.
VLAN MEP: This is not used.
EVC MIP: On Serval, this is the Subscriber VID that identify the subscriber flow in this EVC
where the MIP is active.
This MAC
The MAC of this MEP - can be used by other MEP when unicast is selected (Info only).
Alarm
There is an active alarm on the MEP. Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
187
2-17 ERPS
The ERPS instances are configured here.
Web Interface
To configure the Ethernet Ring Protection Switching parameters in the web interface:
1. Click Configuration and ERPS.
2. Specify the Ethernet Ring Protection Switching parameters.
3. Click Apply to apply the change.
Figure 2-17: The Ethernet Ring Protection Switching
Parameter description:
Power Supply Configuration
Delete
This box is used to mark an EPS for deletion in next save operation.
EPS ID
The ID of the EPS. Click on the ID of an EPS to enter the configuration page. The range is
1-100.
Domain
Port: This will create an EPS in the Port Domain. 'W/P Flow' is a Port.
Architecture
188
Port: This will create a 1+1 EPS.
Port: This will create a 1:1 EPS.
W Flow
The working flow for the EPS - See 'Domain'.
P Flow
The protecting flow for the EPS - See 'Domain'.
W SF MEP
The working Signal Fail reporting MEP.
P SF MEP
The protecting Signal Fail reporting MEP.
APS MEP
The APS PDU handling MEP.
Alarm
There is an active alarm on the EPS.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
189
2-18 MAC Table
Switching of frames is based upon the DMAC address contained in the frame. The
switch builds up a table that maps MAC addresses to switch ports for knowing which
ports the frames should go to (based upon the DMAC address in the frame). This table
contains both static and dynamic entries. The static entries are configured by the
network administrator if the administrator wants to do a fixed mapping between the
DMAC address and switch ports.
The frames also contain a MAC address (SMAC address), which shows the MAC
address of the equipment sending the frame. The SMAC address is used by the switch
to automatically update the MAC table with these dynamic MAC addresses. Dynamic
entries are removed from the MAC table if no frame with the corresponding SMAC
address have been seen after a configurable age time
Web Interface
To configure MAC Address Table in the web interface:
Aging Configuration
1. Click configuration.
2. Specify the Disable Automatic Aging and Aging Time.
3. Click Apply.
MAC Table Learning
1. Click configuration.
2. Specify the Port Members (Auto, Disable, Secure).
3. Click Apply.
Static MAC Table Configuration
1. Click configuration and Add new Static entry.
2. Specify the VLAN IP and Mac address, Port Members.
3. Click Apply.
Figure 2-18: The MAC Address Table Configuration
190
Parameter description:
Aging Configuration :
By default, dynamic entries are removed from the MAC table after 300 seconds. This
removal is also called aging.
Configure aging time by entering a value here in seconds; for example, Age time
seconds.
The allowed range is 10 to 1000000 seconds.
Disable the automatic aging of dynamic entries by checking Disable automatic
aging.
MAC Table Learning
If the learning mode for a given port is greyed out, another module is in control of the
mode, so that it cannot be changed by the user. An example of such a module is the
191
MAC-Based Authentication under 802.1X. Each port can do learning based upon the
following settings:
Auto :
Learning is done automatically as soon as a frame with unknown SMAC is received.
Disable :
No learning is done.
Secure :
Only static MAC entries are learned, all other frames are dropped.
NOTE: Make sure that the link used for managing the switch is
added to the Static Mac Table before changing to secure
learning mode, otherwise the management link is lost and can
only be restored by using another non-secure port or by
connecting to the switch via the serial interface.
Static MAC Table Configuration
The static entries in the MAC table are shown in this table. The static MAC table can
contain 64 entries. The maximum of 64 entries is for the whole stack, and not per
switch.
The MAC table is sorted first by VLAN ID and then by MAC address.
Delete :
Check to delete the entry. It will be deleted during the next save.
VLAN ID :
The VLAN ID of the entry.
MAC Address :
The MAC address of the entry.
Port Members :
Checkmarks indicate which ports are members of the entry. Check or uncheck as
needed to modify the entry.
192
Adding a New Static Entry :
Click to add a new entry to the static MAC table. Specify the VLAN ID, MAC address,
and port members for the new entry. Click "Apply".
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
193
2-19 VLAN Translation
2- 19.1 Port to Group Mapping
This page allows you to configure switch Ports to use a given VLAN Translation Mapping
Group. This will enable all VLAN Translation mappings of that group (if any) on the selected
switch port.
The displayed settings are:
Web Interface
To configure Port to Group Mapping in the web interface:
1. Click configuration, VLAN Translation and Port to Group Mapping
2. Specify the Port and Group Configuration.
3. Click Apply.
Figure 2-19.1: The Port to Group Mapping
Parameter description:
Power Supply Configuration
Port:
194
The Port column shows the list of ports for which you can configure the VLAN
Translation Mapping Group.
Default
To set the switch port to use the default VLAN Translation Group click the checkbox
and press Save.
Group ID
The VLAN Translation mappings are organized into Groups, identified by the Group
ID. This way a port is configured to use a number of VLAN Translation mappings
easily by simply configuring it to use a given group. Then number of possible
groups in a switch is equal to the number of ports present in this switch. A port can
be configured to use any of the groups, but only one at any given time. Multiple
ports can be configured to use the same group. A valid Group ID is an integer value
from 1 to 12.
Note: By default, each port is set to use the group with Group ID equal to the port
number. For example, port #1 is by default set to use group with GID = 1.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values
2- 19.2 VID Translation Mapping
This page displays current VLAN Translation mapping configurations. The settings can also be
configured here.
Web Interface
To configure VID Translation Mapping in the web interface:
1. Click configuration, VLAN Translation and VID Translation Mapping.
2. Specify the Group ID, VID and TVID.
3. Click Apply.
Figure 2-19.2: The VID Translation Mapping
195
Parameter description:
Power Supply Configuration
Group ID
The VLAN Translation mappings are organized into Groups, identified by the Group ID.
This way a port is configured to use a number of VLAN Translation mappings easily by
simply configuring it to use a given group. Then number of possible groups in a switch is
equal to the number of ports present in this switch. A port can be configured to use any
of the groups, but only one at any given time. Multiple ports can be configured to use the
same group. A valid Group ID is an integer value from 1 to 12.
Note: By default, each port is set to use the group with Group ID equal to the port
number. For example, port #1 is by default set to use group with GID = 1.
VID
Indicates the VLAN of the mapping (i.e. 'source' VLAN). A valid VLAN ID ranges from 1 to
4095.
TVID
Indicates the VLAN ID to which VLAN ID of an ingress frame will be translated to (granted
that the mapping is enabled on the ingress port that the frame arrived at). A valid VLAN
ID ranges from 1 to 4095.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values
196
Cancel- Return to the previous page; any changes made locally will be undone.
2-20 VLANs
To assign a specific VLAN for management purpose. The management VLAN is used
to establish an IP connection to the switch from a workstation connected to a port in
the VLAN. This connection supports a VSM, SNMP, and Telnet session. By default, the
active management VLAN is VLAN 1, but you can designate any VLAN as the
management VLAN using the Management VLAN window. Only one management
VLAN can be active at a time.
When you specify a new management VLAN, your HTTP connection to the old
management VLAN is lost. For this reason, you should have a connection between
your management station and a port in the new management VLAN or connect to the
new management VLAN through a multi-VLAN route
Web Interface
To configure VLAN membership configuration in the web interface:
1. Click Configuration VLANS.
2. Specify Existing VLANs, Ether type for Custom S-ports
3. Click Apply.
Figure 2-20.1: The VLAN Configuration
197
Parameter description:
Global VLAN Configuration
Existing VLANs :
This field shows the VLANs that are created on the switch.
By default, only VLAN 1 exists. More VLANs may be created by using a list syntax
where the individual elements are separated by commas. Ranges are specified with
a dash separating the lower and upper bound.
The following example will create VLANs 1, 10, 11, 12, 13, 200, and 300:
1,10-13,200,300. Spaces are allowed in between the delimiters.
Ethertype for Custom S-ports :
This field specifies the ethertype/TPID (specified in hexadecimal) used for Custom
S-ports. The setting is in force for all ports whose Port Type is set to S-Custom-Port.
Port VLAN Configuration
Port :
This is the logical port number of this row.
Mode :
The port mode (default is Access) determines the fundamental behavior of the port in
question. A port can be in one of three modes as described below.
Whenever a particular mode is selected, the remaining fields in that row will be either grayed
out or made changeable depending on the mode in question.
Grayed out fields show the value that the port will get when the mode is applied.
Access:
Access ports are normally used to connect to end stations. Dynamic features like Voice VLAN
may add the port to more VLANs behind the scenes. Access ports have the following
characteristics:
198
• Member of exactly one VLAN, the Port VLAN (a.k.a. Access VLAN), which by default is 1,
• accepts untagged frames and C-tagged frames,
• discards all frames that are not classified to the Access VLAN,
• on egress all frames are transmitted untagged.
Trunk:
Trunk ports can carry traffic on multiple VLANs simultaneously, and are normally used to
connect to other switches. Trunk ports have the following characteristics:
• By default, a trunk port is member of all existing VLANs. This may be limited by the use of
Allowed VLANs,
• unless VLAN Trunking is enabled on the port, frames classified to a VLAN that the port is
not a member of will be discarded,
• by default, all frames but frames classified to the Port VLAN (a.k.a. Native VLAN) get
tagged on egress. Frames classified to the Port VLAN do not get C-tagged on egress,
• egress tagging can be changed to tag all frames, in which case only tagged frames are
accepted on ingress,
• VLAN trunking may be enabled.
Hybrid:
Hybrid ports resemble trunk ports in many ways, but adds additional port configuration
features. In addition to the characteristics described for trunk ports, hybrid ports have these
abilities:
• Can be configured to be VLAN tag unaware, C-tag aware, S-tag aware, or S-custom-tag
aware,
• ingress filtering can be controlled,
• ingress acceptance of frames and configuration of egress tagging can be configured
independently.
Port VLAN :
Determines the port's VLAN ID (a.k.a. PVID). Allowed VLANs are in the range 1 through 4095,
default being 1.
On ingress, frames get classified to the Port VLAN if the port is configured as VLAN unaware,
the frame is untagged, or VLAN awareness is enabled on the port, but the frame is priority
tagged (VLAN ID = 0).
On egress, frames classified to the Port VLAN do not get tagged if Egress Tagging
configuration is set to untag Port VLAN.
The Port VLAN is called an "Access VLAN" for ports in Access mode and Native VLAN for
ports in Trunk or Hybrid mode.
199
Port Type :
Ports in hybrid mode allow for changing the port type, that is, whether a frame's VLAN tag is
used to classify the frame on ingress to a particular VLAN, and if so, which TPID it reacts on.
Likewise, on egress, the Port Type determines the TPID of the tag, if a tag is required.
Unaware:
On ingress, all frames, whether carrying a VLAN tag or not, get classified to the Port VLAN,
and possible tags are not removed on egress.
C-Port:
On ingress, frames with a VLAN tag with TPID = 0x8100 get classified to the VLAN ID
embedded in the tag. If a frame is untagged or priority tagged, the frame gets classified to
the Port VLAN. If frames must be tagged on egress, they will be tagged with a C-tag.
S-Port:
On ingress, frames with a VLAN tag with TPID = 0x8100 or 0x88A8 get classified to the VLAN
ID embedded in the tag. If a frame is untagged or priority tagged, the frame gets classified to
the Port VLAN. If frames must be tagged on egress, they will be tagged with an S-tag.
S-Custom-Port:
On ingress, frames with a VLAN tag with a TPID = 0x8100 or equal to the Ethertype
configured for Custom-S ports get classified to the VLAN ID embedded in the tag. If a frame
is untagged or priority tagged, the frame gets classified to the Port VLAN. If frames must be
tagged on egress, they will be tagged with the custom S-tag.
Ingress Filtering :
Hybrid ports allow for changing ingress filtering. Access and Trunk ports always have ingress
filtering enabled.
If ingress filtering is enabled (checkbox is checked), frames classified to a VLAN that the port
is not a member of get discarded.
If ingress filtering is disabled, frames classified to a VLAN that the port is not a member of are
accepted and forwarded to the switch engine. However, the port will never transmit frames
classified to VLANs that it is not a member of.
VLAN Trunking :
Trunk and Hybrid ports allow for enabling VLAN trunking.
When VLAN trunking is enabled, frames classified to unknown VLANs are accepted on the
port whether ingress filtering is enabled or not.
200
This is useful in scenarios where a cloud of intermediary switches must bridge VLANs that
haven't been created. By configuring the ports that connect the cloud of switches as trunking
ports, they can seemlessly carry those VLANs from one end to the other.
Ingress Acceptance :
Hybrid ports allow for changing the type of frames that are accepted on ingress.
Tagged and untagged
both tagged and untagged frames are accepted.
Tagged Only
Only tagged frames are accepted on ingress. Untagged frames are discarded.
Untagged Only
Only untagged frames are accepted on ingress. Tagged frames are discarded.
Egress Tagging :
Ports in Trunk and Hybrid mode may control the tagging of frames on egress.
Untag Port VLAN
Frames classified to the Port VLAN are transmitted untagged. Other frames are transmitted
with the relevant tag.
Tag All
All frames, whether classified to the Port VLAN or not, are transmitted with a tag.
Untag All
All frames, whether classified to the Port VLAN or not, are transmitted without a tag.
This option is only available for ports in Hybrid mode.
Allowed VLANs :
Ports in Trunk and Hybrid mode may control which VLANs they are allowed to become
members of. Access ports can only be member of one VLAN, the Access VLAN.
The field's syntax is identical to the syntax used in the Existing VLANs field. By default, a port
may become member of all possible VLANs, and is therefore set to 1-4095.
The field may be left empty, which means that the port will not be member of any of the
existing VLANs, but if it is configured for VLAN Trunking it will still be able to carry all
unknown VLANs.
201
Forbidden VLANs :
A port may be configured to never be member of one or more VLANs. This is particularly
useful when dynamic VLAN protocols like MVRP and GVRP must be prevented from
dynamically adding ports to VLANs.
The trick is to mark such VLANs as forbidden on the port in question. The syntax is identical
to the syntax used in the Existing VLANs field.
By default, the field is left blank, which means that the port may become a member of all
possible VLANs.
202
2-21 Private VLANs
In a private VLAN, communication between ports in that private VLAN is not permitted.
A VLAN can be configured as a private VLAN.
2-21.1 Membership
The Private VLAN membership configurations for the switch can be monitored and
modified here. rivate VLANs can be added or deleted here. Port members of each
Private VLAN can be added or removed here.
Private VLANs are based on the source port mask, and there are no connections to
VLANs. This means that VLAN IDs and Private VLAN IDs can be identical.
A port must be a member of both a VLAN and a Private VLAN to be able to forward
packets. By default, all ports are VLAN unaware and members of VLAN 1 and Private
VLAN 1.
A VLAN unaware port can only be a member of one VLAN, but it can be a member
of multiple Private VLANs.
Web Interface
To configure Membership in the web interface:
1. Click Configuration, Private VLANs and Membership.
2. Evoke which port want to enable Port Members.
3. Click Apply.
Figure 2-21.1: The Membership
Parameter description:
203
Delete
To delete a private VLAN entry, check this box. The entry will be deleted during the next
save.
Private VLAN ID
Indicates the ID of this particular private VLAN.
Port Members
A row of check boxes for each port is displayed for each private VLAN ID. To include a
port in a Private VLAN, check the box. To remove or exclude the port from the Private
VLAN, make sure the box is unchecked. By default, no ports are members, and all boxes
are unchecked.
Adding a New Private VLAN
Click to add a new private VLAN ID. An empty row is added to the table, and the private
VLAN can be configured as needed. The allowed range for a private VLAN ID is the same
as the switch port number range. Any values outside this range are not accepted, and a
warning message appears. Click "OK" to discard the incorrect entry, or click "Cancel" to
return to the editing and make a correction.
The Private VLAN is enabled when you click "Save".
The button can be used to undo the addition of new Private VLANs
Buttons:
Refresh- Click to refresh the page immediately.
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
204
2-21.2 Port Isolation
This page is used for enabling or disabling port isolation on ports in a Private VLAN.
A port member of a VLAN can be isolated to other isolated ports on the same VLAN and
Private VLAN.
Web Interface
To configure Port Isolation configuration in the web interface:
1. Click Configuration, Private VLAN, Port Isolation.
2. Evoke which port want to enable Port Isolation
3. Click Apply.
Figure 2-21.2: The Port Isolation Configuration
Parameter description:
Port Members :
A check box is provided for each port of a private VLAN. When checked, port
isolation is enabled on that port. When unchecked, port isolation is disabled on
that port. By default, port isolation is disabled on all ports.
Buttons:
Refresh- Click to refresh the page immediately.
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
205
values.
206
2-22 VCL
2-22.1 MAC-based VLAN
MAC address-based VLAN decides the VLAN for forwarding an untagged frame based
on the source MAC address of the frame.
A most common way of grouping VLAN members is by port, hence the name
port-based VLAN. Typically, the device adds the same VLAN tag to untagged packets
that are received through the same port. Later on, these packets can be forwarded in
the same VLAN. Port-based VLAN is easy to configure, and applies to networks where
the locations of terminal devices are relatively fixed. As mobile office and wireless
network access gain more popularity, the ports that terminal devices use to access the
networks are very often non-fixed. A device may access a network through Port A this
time, but through Port B the next time. If Port A and Port B belong to different VLANs,
the device will be assigned to a different VLAN the next time it accesses the network.
As a result, it will not be able to use the resources in the old VLAN. On the other hand,
if Port A and Port B belong to the same VLAN, after terminal devices access the
network through Port B, they will have access to the same resources as those
accessing the network through Port A do, which brings security issues. To provide user
access and ensure data security in the meantime, the MAC-based VLAN technology is
developed.
MAC-based VLANs group VLAN members by MAC address. With MAC-based VLAN
configured, the device adds a VLAN tag to an untagged frame according to its source
MAC address. MAC-based VLANs are mostly used in conjunction with security
technologies such as 802.1X to provide secure, flexible network access for terminal
devices.
Web Interface
To configure MAC address-based VLAN configuration in the web interface:
1. Click VLC, MAC-based VLAN configuration and add new entry.
2. Specify the MAC address and VLAN ID.
3. Click Apply.
207
Figure 2-22.1: The MAC-based VLAN Membership Configuration
Parameter description:
Delete :
To delete a MAC-based VLAN entry, check this box and press save. The entry will be
deleted on the selected switch in the stack.
MAC Address :
Indicates the MAC address.
VLAN ID :
Indicates the VLAN ID.
Port Members :
A row of check boxes for each port is displayed for each MAC-based VLAN entry. To
include a port in a MAC-based VLAN, check the box. To remove or exclude the port
from the MAC-based VLAN, make sure the box is unchecked. By default, no ports
are members, and all boxes are unchecked.
Adding a New MAC-based VLAN
Click to add a new MAC-based VLAN entry. An empty row is added to the table, and
the MAC-based VLAN entry can be configured as needed. Any unicast MAC address
can be configured for the MAC-based VLAN entry. No broadcast or multicast MAC
addresses are allowed. Legal values for a VLAN ID are 1 through 4095.
The MAC-based VLAN entry is enabled on the selected stack switch unit when you
208
click on "Save". A MAC-based VLAN without any port members on any stack unit
will be deleted when you click "Save".
The button can be used to undo the addition of new MAC-based VLANs.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
209
2-22.2 Protocol -based VLAN
This section describe Protocol -based VLAN, The Switch support Protocol include
Ethernet LLC SNAP Protocol,
LLC
The Logical Link Control (LLC) data communication protocol layer is the upper
sub-layer of the Data Link Layer (which is itself layer 2, just above the Physical Layer) in
the seven-layer OSI reference model. It provides multiplexing mechanisms that make it
possible for several network protocols (IP, IPX, Decent and Appletalk) to coexist within
a multipoint network and to be transported over the same network media, and can
also provide flow control and automatic repeat request (ARQ) error management
mechanisms.
SNAP
The Subnetwork Access Protocol (SNAP) is a mechanism for multiplexing, on networks
using IEEE 802.2 LLC, more protocols than can be distinguished by the 8-bit 802.2
Service Access Point (SAP) fields. SNAP supports identifying protocols by Ethernet type
field values; it also supports vendor-private protocol identifier spaces. It is used with
IEEE 802.3, IEEE 802.4, IEEE 802.5, IEEE 802.11 and other IEEE 802 physical network
layers, as well as with non-IEEE 802 physical network layers such as FDDI that use 802.2
LLC.
2-22.2.1 Protocol to Group
This page allows you to add new protocols to Group Name (unique for each Group)
mapping entries as well as allow you to see and delete already mapped entries for the
selected stack switch unit switch.
Web Interface
To configure Protocol -based VLAN configuration in the web interface:
1. Click Protocol -based VLAN configuration and add new entry.
2. Specify the Ethernet LLC SNAP Protocol and Group Name.
3. Click Apply.
210
Figure 2-22.2.1: The Protocol to Group Mapping Table
Parameter description:
Delete :
To delete a Protocol to Group Name map entry, check this box. The entry will be
deleted on the switch during the next Save.
Frame Type :
Frame Type can have one of the following values:
1. Ethernet
2. LLC
3. SNAP
NOTE: On changing the Frame type field, valid value of the
following text field will vary depending on the new frame type
you selected.
Value :
Valid value that can be entered in this text field depends on the option selected
from the the preceding Frame Type selection menu.
Below is the criteria for three different Frame Types:
1. For Ethernet: Values in the text field when Ethernet is selected as a Frame
Type is called etype. Valid values for etype ranges from 0x0600-0xffff
211
2. For LLC: Valid value in this case is comprised of two different sub-values.
a. DSAP: 1-byte long string (0x00-0xff)
b. SSAP: 1-byte long string (0x00-0xff)
3. For SNAP: Valid value in this case also is comprised of two different
sub-values.
a.OUI: OUI (Organizationally Unique Identifier) is value in format of xx-xx-xx
where each pair (xx) in string is a hexadecimal value ranges from 0x00-0xff.
b. PID: If the OUI is hexadecimal 000000, the protocol ID is the Ethernet type
(EtherType) field value for the protocol running on top of SNAP; if the OUI is
an OUI for a particular organization, the protocol ID is a value assigned by that
organization to the protocol running on top of SNAP.
In other words, if value of OUI field is 00-00-00 then value of PID will be etype
(0x0600-0xffff) and if value of OUI is other than 00-00-00 then valid value of
PID will be any value from 0x0000 to 0xffff.
Group Name :
A valid Group Name is a unique 16-character long string for every entry which
consists of a combination of alphabets (a-z or A-Z) and integers (0-9).
NOTE: Special character and underscore (_) are not allowed.
Adding a New Group to VLAN mapping entry :
Click to add a new entry in mapping table. An empty row is added to the table;
Frame Type, Value and the Group Name can be configured as needed.
The button can be used to undo the addition of new entry.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
Upper right icon (Refresh):
You can click them for refresh the Protocol Group Mapping information by manual.
212
213
2-22.2.2 Group to VLAN
This section allows you to map an already configured Group Name to a VLAN for the
selected stack switch unit switch.
Web Interface
To Display Group Name to VLAN mapping table configured in the web interface:
1. Click Group Name VLAN configuration and add new entry.
2. Specify the Group Name and VLAN ID.
3. Click Apply.
Figure 2-22.2.2: The Group Name of VLAN Mapping Table
Parameter description:
Delete :
To delete a Group Name to VLAN map entry, check this box. The entry will be
deleted on the switch during the next Save
Group Name :
A valid Group Name is a string of almost 16 characters which consists of a
combination of alphabets (a-z or A-Z) and integers (0-9), no special character is
allowed. Whichever Group name you try map to a VLAN must be present in
Protocol to Group mapping table and must not be perused by any other existing
mapping entry on this page.
214
VLAN ID :
Indicates the ID to which Group Name will be mapped. A valid VLAN ID ranges from
1-4095.
Port Members :
A row of check boxes for each port is displayed for each Group Name to VLAN ID
mapping. To include a port in a mapping, check the box. To remove or exclude the
port from the mapping, make sure the box is unchecked. By default, no ports are
members, and all boxes are unchecked.
Adding a New Group to VLAN mapping entry :
Click to add a new entry in mapping table. An empty row is added to the table, the
Group Name, VLAN ID and port members can be configured as needed. Legal
values for a VLAN ID are 1 through 4095. The button can be used to undo the
addition of new entry.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
Auto-refresh :
To evoke the auto-refresh icon then the device will refresh the information
automatically.
Upper right icon (Refresh):
You can click them for refresh the Protocol Group Mapping information by manual.
2-22.3 IP Subnet-based VLAN
The IP subnet-based VLAN entries can be configured here. This page allows for adding,
updating and deleting IP subnet-based VLAN entries and assigning the entries to
different ports. This page shows only static entries.
Web Interface
To Display IP subnet-based VLAN Membership to configured in the web interface:
215
1. Click VCL, Group Name VLAN configuration and add new entry.
2. Specify the VCE ID, IP Address, Mask Length, VLAN ID and select Port Members.
3. Click Apply.
Figure 2-22.3: IP Subnet-based VLAN Membership Configuration
Parameter description:
Delete
To delete a IP subnet-based VLAN entry, check this box and press save. The entry
will be deleted on the selected switch in the stack.
VCE ID
Indicates the index of the entry. It is user configurable. Its value ranges from 0-128.
If a VCE ID is 0, application will auto-generate the VCE ID for that entry. Deletion
and lookup of IP subnet-based VLAN are based on VCE ID.
IP Address
Indicates the IP address.
Mask Length
Indicates the network mask length.
VLAN ID
Indicates the VLAN ID. VLAN ID can be changed for the existing entries.
Port Members
A row of check boxes for each port is displayed for each IP subnet-based VLAN
entry. To include a port in a IP subnet-based VLAN, check the box. To remove or
216
exclude the port from the IP subnet-based VLAN, make sure the box is unchecked.
By default, no ports are members, and all boxes are unchecked.
Adding a New IP subnet-based VLAN
Click “Add New Entry” to add a new IP subnet-based VLAN entry. An empty row is
added to the table, and the IP subnet-based VLAN entry can be configured as
needed. Any IP address/mask can be configured for the IP subnet-based VLAN
entry. Legal values for a VLAN ID are 1 through 4095.
The IP subnet-based VLAN entry is enabled on the selected stack switch unit when
you click on "Save". The “Delete” button can be used to undo the addition of new IP
subnet-based VLANs. The maximum possible IP subnet-based VLAN entries are
limited to 128.
217
2-23 VOICE VLAN
Voice VLAN is VLAN configured specially for voice traffic. By adding the ports with
voice devices attached to voice VLAN, we can perform QoS-related configuration for
voice data, ensuring the transmission priority of voice traffic and voice quality.
2-23.1 Configuration
The Voice VLAN feature enables voice traffic forwarding on the Voice VLAN, then the
switch can classify and schedule network traffic. It is recommended that there be two
VLANs on a port - one for voice, one for data. Before connecting the IP device to the
switch, the IP phone should configure the voice VLAN ID correctly. It should be
configured through its own GUI.
Web Interface
To configure Voice VLAN in the web interface:
1. Select “Enabled” in the Voice VLAN Configuration.
2. Specify VLAN ID Aging Time Traffic Class.
3. Specify (Port Mode, Security, Discovery Protocol)
in the Port Configuration
4. Click Apply.
Figure 2-23.1: The Voice VLAN Configuration
218
219
Parameter description:
Mode :
Indicates the Voice VLAN mode operation. We must disable MSTP feature before
we enable Voice VLAN. It can avoid the conflict of ingress filtering. Possible modes
are:
Enabled: Enable Voice VLAN mode operation.
Disabled: Disable Voice VLAN mode operation.
VLAN ID :
Indicates the Voice VLAN ID. It should be a unique VLAN ID in the system and
cannot equal each port PVID. It is a conflict in configuration if the value equals
management VID, MVR VID, PVID etc. The allowed range is 1 to 4095.
Aging Time :
Indicates the Voice VLAN secure learning aging time. The allowed range is 10 to
10000000 seconds. It is used when security mode or auto detect mode is enabled.
In other cases, it will be based on hardware aging time. The actual aging time will be
situated between the [age_time; 2 * age_time] interval.
Traffic Class :
Indicates the Voice VLAN traffic class. All traffic on the Voice VLAN will apply this
class.
Port Mode :
Indicates the Voice VLAN port mode.
When the port mode isn't equal disabled, we must disable MSTP feature before we
enable Voice VLAN. It can avoid the conflict of ingress filtering.
Possible port modes are:
Disabled: Disjoin from Voice VLAN.
Auto: Enable auto detect mode. It detects whether there is VoIP phone attached to
the specific port and configures the Voice VLAN members automatically.
Forced: Force join to Voice VLAN.
Port Security :
220
Indicates the Voice VLAN port security mode. When the function is enabled, all
non-telephonic MAC addresses in the Voice VLAN will be blocked for 10 seconds.
Possible port modes are:
Enabled: Enable Voice VLAN security mode operation.
Disabled: Disable Voice VLAN security mode operation.
Port Discovery Protocol :
Indicates the Voice VLAN port discovery protocol. It will only work when auto detect
mode is enabled. We should enable LLDP feature before configuring discovery
protocol to "LLDP" or "Both". Changing the discovery protocol to "OUI" or "LLDP"
will restart auto detect process. Possible discovery protocols are:
OUI: Detect telephony device by OUI address.
LLDP: Detect telephony device by LLDP.
Both: Both OUI and LLDP.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
2-23.2 OUI
The section describes to Configure VOICE VLAN OUI table. The maximum entry
number is 16. Modifying the OUI table will restart auto detection of OUI process.
Web Interface
To configure Voice VLAN OUI Table in the web interface:
1. Select “Add new entry”, “delete” in the Voice VLAN OUI table..
2. Specify Telephony OUI, Description.
3. Click Apply.
221
Figure 2-23.2: The Voice VLAN OUI Table
Parameter description:
Delete :
Check to delete the entry. It will be deleted during the next save.
Telephony OUI :
A telephony OUI address is a globally unique identifier assigned to a vendor by IEEE.
It must be 6 characters long and the input format is "xx-xx-xx" (x is a hexadecimal
digit).
Description :
The description of OUI address. Normally, it describes which vendor telephony
device it belongs to. The allowed string length is 0 to 32.
Add New entry :
Click to add a new entry in Voice VLAN OUI table. An empty row is added to the
table, the Telephony OUI, Description.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
222
2-24 Ethernet Services
2-24.1 Ports
This page displays current EVC port configurations. The settings can also be
configured here.
Web Interface
To configure Port Configuration in the web interface:
1. Click configuration, Ethernet Services and ports.
2. Specify DEI Mode, Tag Mode and Address Mode.
3. Click Apply.
Figure 2-24.1: The Port Configuration
Parameter description:.
Port
The logical port for the settings contained in the same row.
DEI Mode
The DEI mode for an NNI port determines whether frames transmitted on the port will
have the DEI field in the outer tag marked based on the colour of the frame. The allowed
values are:
Coloured: The DEI is 1 for yellow frames and 0 for green frames.
223
Fixed: The DEI value is determined by ECE rules.
Tag Mode
The tag mode specifying whether the EVC classification must be based on the outer or
inner tag. This can be used on NNI ports connected to another service provider, where an
outer "tunnel" tag is added together with the inner tag identifying the EVC. The allowed
values are:
Inner: Enable inner tag in EVC classification.
Outer: Enable outer tag in EVC classification.
Address Mode
The IP/MAC address mode specifying whether the EVC classification must be based on
source (SMAC/SIP) or destination (DMAC/DIP) addresses. The allowed values are:
Source: Enable SMAC/SIP matching.
Destination: Enable DMAC/DIP matching.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
2-24.2 L2CP
This page displays current EVC L2CP configurations. The settings can also be
configured here.
Web Interface
To configure L2CP Port Configuration in the web interface:
1. Click configuration, Ethernet Services and L2CP.
2. Specify DMAC and L2CP Mode.
3. Click Apply.
Figure 2-24.2: The L2CP Port Configuration
224
Parameter description:.
DMAC
The destination BPDU MAC addresses (01-80-C2-00-00-0X) and GARP
(01-80-C2-00-00-2X) MAC addresses for the settings contained in the same row.
L2CP Mode
The L2CP mode for the specific port. The possible values are:
Peer: Allow to peer L2CP frames.
Forward: Allow to forward L2CP frames.Buttons:
Buttons:
Refresh-Click to refresh the page.
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
225
values.
2-24.3 Bandwidth Profiles
This page displays current EVC ingress bandwidth profile configurations. These
policers may be used to limit the traffic received on UNI ports. The settings can also
be configured here.
Web Interface
To configure Bandwidth Profiles in the web interface:
1. Click configuration, Ethernet Services and Bandwidth Profiles.
2. Specify State, Type, Policer Mode and Rate Type.
3. Click Apply.
Figure 2-24.3: The Port Configuration
Parameter description:.
Start Policer ID
The start Policer ID for displaying the table entries. The allowed range is
from 1 through 256.
Number of Entries
226
The number of entries per page. The allowed range is from 2 through 256.
Policer ID
The Policer ID is used to identify one of the 256policers.
State
The administrative state of the bandwidth profile. The allowed values are:
Enabled: The bandwidth profile enabled.
Disabled: The bandwidth profile is disabled.
Type
The policer type of the bandwidth profile. The allowed values are:
MEF: MEF ingress bandwidth profile.
Single: Single bucket policer.
Policer Mode
The colour mode of the bandwidth profile. The allowed values are:
Coupled: Colour-aware mode with coupling enabled.
Aware: Colour-aware mode with coupling disabled.
Rate Type
The rate type of the bandwidth profile. The allowed values are:
Data: Specify that this bandwidth profile operates on data rate.
Line: Specify that this bandwidth profile operates on line rate.
CIR
The Committed Information Rate of the bandwidth profile. The allowed range is
from 0 through 10000000 kilobit per second.
CBS
The Committed Burst Size of the bandwidth profile. The allowed range is
from 0 through 100000bytes.
EIR
The Excess Information Rate for MEF type bandwidth profile. The allowed range is
from 0through 10000000 kilobit per second.
EBS
227
The Excess Burst Size for MEF type bandwidth profile. The allowed range is
from 0 through 100000 bytes..
Buttons:
Refresh- Refreshes the displayed table starting from the input fields.
|<<- Updates the table, starting with the first entry in the table.
<<- Updates the table, ending at the entry before the first entry currently
displayed.
>>- Updates the table, starting with the entry after the last entry currently
displayed.
>>|- Updates the table, ending at the last entry in the table.
Apply- Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
2-24.4 EVCs
This page displays current EVC configurations. On this system, only Provider Bridge
based EVCs are supported.
Web Interface
To configure EVCs Control list Configuration in the web interface:
1. Click configuration, Ethernet Services and EVCs.
2. Specify EVC ID, VID, IVID, Learning, Inner Tag and Outer Tag.
3. Click Apply.
Figure 2-24.4: The EVCs
229
depending on the NNI port VLAN configuration. The range is from 1through 4095.
IVID
The Internal/classified VLAN ID in the PB network. The range is
from 1 through 4095.
Learning
The learning mode for the EVC controls whether source MAC addresses are learned
for frames matching the EVC. Learning may be disabled if the EVC only includes two
UNI/NNI ports. The possible values are:
Enabled: Learning is enabled (MAC addresses are learned).
Disabled: Learning is disabled (MAC addresses are not learned).
Inner Tag Type
The inner tag type is used to determine whether an inner tag is inserted in frames
forwarded to NNI ports. The possible values are:
None: An inner tag is not inserted.
C-tag: An inner C-tag is inserted.
S-tag: An inner S-tag is inserted.
S-custom-tag: An inner tag is inserted and the tag type is determined by the VLAN
port configuration of the NNI.
Inner VID Mode
The inner VID Mode affects the VID in the inner and outer tag. The possible values
are:
Normal: The VID of the two outer tags aren't swapped.
Tunnel: The VID of the two outer tags are swapped, so that the VID of the outer tag
is taken from the Inner Tag configuration and the VID of the inner tag is the EVC VID.
In this mode, the NNI ports are normally configured to do EVC classification based
on the inner tag.
Inner Tag VID
The Inner tag VLAN ID. The allowed range is from 0 through 4095.
Inner Tag PCP/DEI Preservation
The inner tag PCP and DEI preservation. The possible values are:
Preserved: The inner tag PCP and DEI is preserved.
Fixed: The inner tag PCP and DEI is fixed.
230
Inner Tag PCP
The inner tag PCP value. The allowed range is from 0 through 7.
Inner Tag DEI
The inner tag DEI value. The allowed value is 0 or 1.
Outer Tag VID
The EVC outer tag VID for UNI ports. The allowed range is from 0 through 4095.
NNI Ports
The list of Network to Network Interfaces for the EVC.
Modification Buttons:
You can modify each EVC in the table using the following buttons:
: Edits the EVC row.
: Deletes the EVC.
: Adds new EVC.
Buttons:
Refresh –Click to refresh the page.
Remove All- Click to remove all EVCs.
2-24.5 ECEs
This page displays the current EVC Control Entries (ECEs). The settings can also be
configured here.
Web Interface
To configure ECE Control List Configuration in the web interface:
1. Click configuration, Ethernet Services and ECEs.
2. Specify ECE ID, Ingress Matching, Actions and Egress outer Tag.
3. Click Apply.
Figure 2-24.5: The ECEs
231
Parameter description:.
232
ECE ID
The ECE ID identifies the ECE. Unique ECE IDs are automatically assigned to ECEs added.
The possible range is from 1 through 256
Ingress Matching
UNI Ports
The list of User Network Interfaces for the ECE.
Tag Type
The tag type for the ECE. The possible values are:
Any: The ECE will match both tagged and untagged frames.
Untagged: The ECE will match untagged frames only.
C-Tagged: The ECE will match custom tagged frames only.
S-Tagged: The ECE will match service tagged frames only.
Tagged: The ECE will match tagged frames only.
VID
The VLAN ID for the ECE. It only significant if tag type 'Tagged' is selected. The
possible values are:
Specific: The range is from 0 through 4095.
Any: The ECE will match any VLAN ID.
PCP
The PCP value for the ECE. It only significant if tag type 'Tagged' is selected. The
possible values are:
Specific: The ECE will match a specific PCP in the range 0 through 7.
Range: The ECE will match PCP values in the selected
range 0-1, 2-3, 4-5, 6-7, 0-3or 4-7.
Any: The ECE will match any PCP value.
DEI
The DEI value for the ECE. It only significant if tag type 'Tagged' is selected. The
possible values is: 0, 1 or Any.
Frame Type
The frame type for the ECE. The possible values are:
Any: The ECE will match any frame type.
233
IPv4: The ECE will match IPv4 frames only.
IPv6: The ECE will match IPv6 frames only.
Actions
Direction
The EVCs and ECEs are used to setup flows in one or both directions as determined
by the ECE Direction parameter. If the ECE is bidirectional, the ingress rules of the
NNI ports will be setup to match the traffic being forwarded to NNI ports. Possible
values are:
Both: Bidirectional.
UNI-to-NNI: Unidirectional from UNI to NNI.
NNI-to-UNI: Unidirectional from NNI to UNI.
EVC ID
The EVC ID for the ECE. The ECE is only active when mapping to an existing EVC.
Possible values are:
Specific: The range is from 1 through 256.
None: The ECE does not map to an EVC.
Tag Pop Count
The ingress tag pop count for the ECE. The possible range is from 0 through 2.
Policy ID
The ACL Policy ID for the ECE. The range is from 0 through 255.
Class
The traffic class for the ECE. The range is from 0through 7.
Egress Outer Tag
Outer Tag Mode
The outer tag for nni-to-uni direction for the ECE. The possible values are:
Enable: Enable outer tag for nni-to-uni direction for the ECE.
Disable: Disable outer tag for nni-to-uni direction for the ECE.
Outer Tag PCP/DEI Preservation
The outer tag PCP and DEI preservation for the ECE. The possible values are:
234
Preserved: The outer tag PCP and DEI are preserved.
Disable: The outer tag PCP and DEI are fixed.
Outer Tag PCP
The outer tag PCP value for the ECE. The possible range is from 0 through 7.
Outer Tag DEI
The outer tag DEI value for the ECE. The possible value is 0 or 1.
Conflict
Indicates the hardware status of the specific ECE. The specific ECE is not applied to
the hardware due to hardware limitations.
Modification Buttons
You can modify each ECE (EVC Control Entry) in the table using the following buttons:
: Inserts a new ECE before the current row.
: Edits the ECE row.
: Moves the ECE up the list.
: Moves the ECE down the list.
: Deletes the ECE.
: The lowest plus sign adds a new entry at the bottom of the ECE listings.
Buttons:
Refresh –Click to refresh the page.
Remove All- Click to remove all ECEs.
2-25 QoS
The switch support four QoS queues per port with strict or weighted fair queuing
scheduling. It supports QoS Control Lists (QCL) for advance programmable QoS
classification, based on IEEE 802.1p, Ethertype, VID, IPv4/IPv6 DSCP and UDP/TCP
ports and ranges.
High flexibility in the classification of incoming frames to a QoS class. The QoS
235
classification looks for information up to Layer 4, including IPv4 and IPv6 DSCP, IPv4
TCP/UDP port numbers, and user priority of tagged frames. This QoS classification
mechanism is implemented in a QoS control list (QCL). The QoS class assigned to a
frame is used throughout the device for providing queuing, scheduling, and
congestion control guarantees to the frame according to what was configured for that
specific QoS class.
The switch support advanced memory control mechanisms providing excellent
performance of all QoS classes under any traffic scenario, including jumbo frame. A
super priority queue with dedicated memory and strict highest priority in the
arbitration. The ingress super priority queue allows traffic recognized as CPU traffic to
be received and queued for transmission to the CPU even when all the QoS class
queues are congested.
2-25.1 Port Classification
The section allows you to configure the basic QoS Ingress Classification settings for all
switch ports. and the settings relate to the currently selected stack unit, as reflected by
the page header.
Web Interface
To configure the QoS Port Classification parameters in the web interface:
1. Click Configuration, QoS, Port Classification
2. Scroll to select QoS class, DP Level, PCP and DEI parameters
3. Click the save to save the setting
4. If you want to cancel the setting then you need to click the Reset button.
It will revert to previously saved values
Figure 2-25.1: The QoS Configuration
236
Parameter description:
Port :
The port number for which the configuration below applies.
CoS :
Controls the default class of service.
All frames are classified to a CoS. There is a one to one mapping between CoS,
queue and priority. A CoS of 0 (zero) has the lowest priority.
If the port is VLAN aware, the frame is tagged and Tag Class. is enabled, then the
frame is classified to a CoS that is mapped from the PCP and DEI value in the tag.
Otherwise the frame is classified to the default CoS.
The classified CoS can be overruled by a QCL entry.
Note: If the default CoS has been dynamically changed, then the actual default CoS
is shown in parentheses after the configured default CoS.
DPL :
Controls the default drop precedence level.
All frames are classified to a drop precedence level.
If the port is VLAN aware, the frame is tagged and Tag Class. is enabled, then the
frame is classified to a DPL that is mapped from the PCP and DEI value in the tag.
Otherwise the frame is classified to the default DPL.
The classified DPL can be overruled by a QCL entry.
PCP :
Controls the default PCP value.
All frames are classified to a PCP value.
If the port is VLAN aware and the frame is tagged, then the frame is classified to the
237
PCP value in the tag. Otherwise the frame is classified to the default PCP value.
DEI :
Controls the default DEI value.
All frames are classified to a DEI value.
If the port is VLAN aware and the frame is tagged, then the frame is classified to the
DEI value in the tag. Otherwise the frame is classified to the default DEI value.
Tag Class. :
Shows the classification mode for tagged frames on this port.
Disabled: Use default QoS class and DP level for tagged frames.
Enabled: Use mapped versions of PCP and DEI for tagged frames.
Click on the mode in order to configure the mode and/or mapping.
NOTE: This setting has no effect if the port is VLAN unaware.
Tagged frames received on VLAN unaware ports are always
classified to the default CoS and DPL.
DSCP Based :
Click to Enable DSCP Based QoS Ingress Port Classification.
Address Mode :
The IP/MAC address mode specifying whether the QCL classification must be based
on source (SMAC/SIP) or destination (DMAC/DIP) addresses on this port. The
allowed values are:
Source: Enable SMAC/SIP matching.
Destination: Enable DMAC/DIP matching.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
238
2-25.2 Port Policing
This section provides an overview of f QoS Ingress Port Policers for all switch ports The
Port Policing is useful in constraining traffic flows and marking frames above specific
rates. Policing is primarily useful for data flows and voice or video flows because voice
and video usually maintains a steady rate of traffic
Web Interface
To display the QoS Port Schedulers in the web interface:
1. Click Configuration, QoS, Port Policing
2. Evoke which port need to enable the QoS Ingress Port Policers and type the
Rate limit condition.
3. Scroll to select the Rate limit Unit with kbps, Mbps, fps and kfps.
4. Click Apply to save the configuration.
Figure 2-25.2: The QoS Ingress Port Policers Configuration
Parameter description:
Port :
The logical port for the settings contained in the same row. Click on the port
number in order to configure the schedulers.
239
Enabled :
To evoke which Port you need to enable the QoS Ingress Port Policers function.
Rate :
To set the Rate limit value for this port, the default is 500.
Unit :
To scroll to select what unit of rate includes kbps, Mbps, fps and kfps. The default is
kbps.
Flow Control :
If flow control is enabled and the port is in flow control mode, then pause frames
are sent instead of discarding frames.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
2-25.3 Queue Policing
This page allows you to configure the Queue Policer settings for all switch ports.
The displayed settings are:
Web Interface
To display the Queue Policing in the web interface:
1. Click Configuration, QoS and Queue Policing
2. Specify the Queue Policing parameter.
Figure 2-25.3: The Queue Policing
240
Parameter description:
Port
The port number for which the configuration below applies.
Enable (E)
Enable or disable the queue policer for this switch port.
Rate
Controls the rate for the queue policer. This value is restricted to 100-3276700 when
"Unit" is kbps, and 1-3276 when "Unit" is Mbps. The rate is internally rounded up to
the nearest value supported by the queue policer.
This field is only shown if at least one of the queue policers are enabled.
Unit
Controls the unit of measure for the queue policer rate as kbps or Mbps.
This field is only shown if at least one of the queue policers are enabled.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
2-25.4 Port Scheduler
This section provides an overview of QoS Egress Port Schedulers for all switch ports.
and the ports belong to the currently selected stack unit, as reflected by the page
header.
241
Web Interface
To display the QoS Port Schedulers in the web interface:
1. Click Configuration, QoS, Port Schedulers
2. Display the QoS Egress Port Schedulers
Figure 2-25.4: The QoS Egress Port Schedules
Click the Port index to set the QoS
Egress Port Schedulers
If you select the scheduler
mode with wighted then
the screen will change as
the figure.
242
Parameter description:
Port :
The logical port for the settings contained in the same row. Click on the port
number in order to configure the schedulers.
Mode :
Shows the scheduling mode for this port.
Weight (Qn) :
Shows the weight for this queue and port.
Scheduler Mode :
Controls whether the scheduler mode is "Strict Priority" or "Weighted" on this
switch port.
Queue Shaper Enable :
Controls whether the queue shaper is enabled for this queue on this switch port.
Queue Shaper Rate :
Controls the rate for the queue shaper. The default value is 500. This value is
restricted to 100-1000000 when the "Unit" is "kbps", and it is restricted to 1-13200
when the "Unit" is "Mbps".
Queue Shaper Unit :
Controls the unit of measure for the queue shaper rate as "kbps" or "Mbps". The
default value is "kbps".
Queue Shaper Excess :
Controls whether the queue is allowed to use excess bandwidth.
Queue Scheduler Weight :
Controls the weight for this queue. The default value is "17". This value is restricted
to 1-100. This parameter is only shown if "Scheduler Mode" is set to "Weighted".
Queue Scheduler Percent :
Shows the weight in percent for this queue. This parameter is only shown if
"Scheduler Mode" is set to "Weighted"
243
Port Shaper Enable :
Controls whether the port shaper is enabled for this switch port.
Port Shaper Rate :
Controls the rate for the port shaper. The default value is 500. This value is restricted
to 100-1000000 when the "Unit" is "kbps", and it is restricted to 1-13200 when the
"Unit" is "Mbps".
Port Shaper Unit :
Controls the unit of measure for the port shaper rate as "kbps" or "Mbps". The
default value is "kbps".
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
244
2-25.5 Port Shaping
This section provides an overview of QoS Egress Port Shapers for all switch ports.
Others the user could get all detail information ot the ports belong to the currently
selected stack unit, as reflected by the page header.
Web Interface
To display the QoS Port Shapers in the web interface:
1. Click Configuration, QoS, Port Shapers
2. Display the QoS Egress Port Shapers
Figure 2-25.5: The QoS Egress Port Shapers
Click the Port index to set the
QoS
Egress Port Shapers
If you select the scheduler
mode with wighted then
the screen will change as
the figure.
245
Parameter description:
Port :
The logical port for the settings contained in the same row. Click on the port
number in order to configure the shapers.
Mode :
Shows the scheduling mode for this port.
Shapers (Qn) :
Shows "disabled" or actual queue shaper rate - e.g. "800 Mbps".
Scheduler Mode :
Controls whether the scheduler mode is "Strict Priority" or "Weighted" on this
switch port.
Queue Shaper Enable :
Controls whether the queue shaper is enabled for this queue on this switch port.
Queue Shaper Rate :
Controls the rate for the queue shaper. The default value is 500. This value is
restricted to 100-1000000 when the "Unit" is "kbps", and it is restricted to 1-13200
when the "Unit" is "Mbps".
246
Queue Shaper Unit :
Controls the unit of measure for the queue shaper rate as "kbps" or "Mbps". The
default value is "kbps".
Queue Shaper Excess :
Controls whether the queue is allowed to use excess bandwidth.
Queue Scheduler Weight :
Controls the weight for this queue. The default value is "17". This value is restricted
to 1-100. This parameter is only shown if "Scheduler Mode" is set to "Weighted".
Queue Scheduler Percent :
Shows the weight in percent for this queue. This parameter is only shown if
"Scheduler Mode" is set to "Weighted"
Port Shaper Enable :
Controls whether the port shaper is enabled for this switch port.
Port Shaper Rate :
Controls the rate for the port shaper. The default value is 500. This value is restricted
to 100-1000000 when the "Unit" is "kbps", and it is restricted to 1-13200 when the
"Unit" is "Mbps".
. Port Shaper Unit :
Controls the unit of measure for the port shaper rate as "kbps" or "Mbps". The
default value is "kbps".
. Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
247
2-25.6 Port Tag Remarking
The Section provides user to get an overview of QoS Egress Port Tag Remarking for all
switch ports. Others the ports belong to the currently selected stack unit, as reflected
by the page header. .
Web Interface
To display the QoS Port Tag Remarking in the web interface:
1. Click Configuration, QoS, Port Tag Remarking
Figure 2-25.6: The Port Tag Remarking
Click the Port index to set the
QoS
Port Tag Remarking
248
249
Parameter description:
Mode :
Controls the tag remarking mode for this port.
Classified: Use classified PCP/DEI values.
Default: Use default PCP/DEI values.
Mapped: Use mapped versions of QoS class and DP level.
PCP/DEI Configuration :
Controls the default PCP and DEI values used when the mode is set to Default.
(QoS class, DP level) to (PCP, DEI) Mapping :
Controls the mapping of the classified (QoS class, DP level) to (PCP, DEI) values
when the mode is set to Mapped.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
Cancel – Click to cancel the changes.
250
2-25.7 Port DSCP
The section will teach user to set the QoS Port DSCP configuration that was allowed
you to configure the basic QoS Port DSCP Configuration settings for all switch ports.
Others the settings relate to the currently selected stack unit, as reflected by the page
header.
Web Interface
To configure the QoS Port DSCP parameters in the web interface:
1. Click Configuration, QoS, Port DSCP
2. Evoke to enable or disable the Ingress Translate and Scroll the Classify
Parameter configuration
3. Scroll to select Egress Rewrite parameters
4. Click the save to save the setting
5. If you want to cancel the setting then you need to click the Reset button.
It will revert to previously saved values
Figure 2-25.7: The QoS Port DSCP Configuration
Parameter description:
Port :
251
The Port coulmn shows the list of ports for which you can configure dscp ingress
and egress settings.
Ingress :
In Ingress settings you can change ingress translation and classification settings for
individual ports.
There are two configuration parameters available in Ingress:
3. Translate : To Enable the Ingress Translation click the checkbox
4. Classify: Classification for a port have 4 different values
Disable: No Ingress DSCP Classification.
DSCP=0: Classify if incoming (or translated if enabled) DSCP is 0.
Selected: Classify only selected DSCP for which classification is enabled as
specified in DSCP Translation window for the specific DSCP.
All: Classify all DSCP.
Egress :
Port Egress Rewriting can be one of below parameters
Disable: No Egress rewrite.
Enable: Rewrite enable without remapped.
Remap: DSCP from analyzer is remapped and frame is remarked with
remapped DSCP value.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
Auto-refresh :
To evoke the auto-refresh icon then the device will refresh the information
automatically.
252
Upper right icon (Refresh):
You can click them for refresh the QoS Port DSCP information by manual.
253
2-25.8 DSCP-Based QoS
The section will teach user to configure the DSCP-Based QoS mode that This page
allows you to configure the basic QoS DSCP based QoS Ingress Classification
settings for all switches.
Web Interface
To configure the DSCP –Based QoS Ingress Classification parameters in the web
interface:
1. Click Configuration, QoS, DSCP-Based QoS
2. Evoke to enable or disable the DSCP for Trust
3. Scroll to select QoS Class and DPL parameters
4. Click the save to save the setting
5. If you want to cancel the setting then you need to click the Reset
button. It will revert to previously saved values
Figure 2-25.8: The DSCP-Based QoS Ingress Classification Configuration
254
255
Parameter description:
DSCP :
Maximum number of support ed DSCP values are 64.
Trust :
Click to check if the DSCP value is trusted.
QoS Class :
QoS Class value can be any of (0-7)
DPL :
Drop Precedence Level (0-3)
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
Auto-refresh :
To evoke the auto-refresh icon then the device will refresh the information
automatically.
Upper right icon (Refresh):
You can click them for refresh the DSCP-Based QoS Ingress Classification
information by manual.
256
2-25.9 DSCP Translation
The section describes the switch allows you to configure the basic QoS DSCP
Translation settings for all switches. DSCP translation can be done in Ingress or Egress.
Web Interface
To configure the DSCP Translation parameters in the web interface:
1. Click Configuration, QoS, DSCP Translation
2. Scroll to set the Ingress Translate and Egress Remap DP0 and Remap
DP1 Parameters
3. Evoke to enable or disable Classify
4. Click the save to save the setting
5. If you want to cancel the setting then you need to click the Reset button.
It will revert to previously saved values
Figure 2-25.9: The DSCP Translation Configuration
257
Parameter description:
DSCP :
Maximum number of supported DSCP values are 64 and valid DSCP value ranges
from 0 to 63.
Ingress :
Ingress side DSCP can be first translated to new DSCP before using the DSCP for
QoS class and DPL map.
There are two configuration parameters for DSCP Translation –
1. Translate : DSCP at Ingress side can be translated to any of (0-63) DSCP
values.
2. Classify : Click to enable Classification at Ingress side.
Egress :
There are following configurable parameters for Egress side –
1. Remap DP0 : Select the DSCP value from select menu to which you
want to remap. DSCP value ranges from 0 to 63
2. Remap DP1 : Select the DSCP value from select menu to which you
want to remap. DSCP value ranges from 0 to 63.
There is following configurable parameter for Egress side -
Remap: Select the DSCP value from select menu to which you
want to remap. DSCP value ranges from 0 to 63.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
Auto-refresh :
To evoke the auto-refresh icon then the device will refresh the information
automatically.
258
Upper right icon (Refresh):
You can click them for refresh the DSCP Translation information by manual.
259
2-25.10 DSCP Classification
The section describes to teach user to configure and allows you to map DSCP value to
a QoS Class and DPL value. Others the settings relate to the currently selected stack
unit, as reflected by the page header.
Web Interface
To configure the DSCP Classification parameters in the web interface:
1. Click Configuration, QoS, DSCP Translation
2. Scroll to set the DSCP Parameters
3. Click the save to save the setting
4. If you want to cancel the setting then you need to click the Reset button.
It will revert to previously saved values
Figure 2-25.10: The DSCP Classification Configuration
Parameter description:
QoS Class :
Available QoS Class value ranges from 0 to 7. QoS Class (0-7) can be mapped to
260
followed parameters.
DSCP :
Select DSCP value (0-63) from DSCP menu to map DSCP to corresponding QoS
Class
and DPL value
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
Auto-refresh :
To evoke the auto-refresh icon then the device will refresh the information
automatically.
Upper right icon (Refresh):
You can click them for refresh the DSCP Classification information by manual.
261
2-25.11 QoS Control List
The section shows the QoS Control List (QCL), which is made up of the QCEs. Each row
describes a QCE that is defined. The maximum number of QCEs is 256 on each switch.
Click on the lowest plus sign to add a new QCE to the list.
Web Interface
To configure the QoS Control List parameters in the web interface:
1. Click Configuration, QoS, QoS Contol List
2. Click the to add a new QoS Control List
3. Scroll all parameters and evoke the Port Member to join the QCE rules
4. Click the save to save the setting
5. If you want to cancel the setting then you need to click the Reset button.
It will revert to previously saved values
Figure 2-25.11: The QoS Control List Configuration
262
Parameter description:
QCE# :
Indicates the index of QCE.
Port :
Indicates the list of ports configured with the QCE.
DMAC :
Indicates the destination MAC address. Possible values are:
Any: Match any DMAC.
Unicast: Match unicast DMAC.
Multicast: Match multicast DMAC.
Broadcast: Match broadcast DMAC.
<MAC>: Match specific DMAC.
The default value is 'Any'.
SMAC :
Match specific source MAC address or 'Any'.
If a port is configured to match on DMAC/DIP, this field indicates the DMAC.
Tag Type :
Indicates tag type. Possible values are:
263
Any: Match tagged and untagged frames.
Untagged: Match untagged frames.
Tagged: Match tagged frames.
C-Tagged: Match C-tagged frames.
S-Tagged: Match S-tagged frames.
The default value is 'Any'.
VID :
Indicates (VLAN ID), either a specific VID or range of VIDs. VID can be in the range 1-4095 or
'Any'
PCP :
Priority Code Point: Valid values of PCP are specific (0, 1, 2, 3, 4, 5, 6, 7) or range(0-1, 2-3, 4-5,
6-7, 0-3, 4-7) or 'Any'.
DEI :
Drop Eligible Indicator: Valid value of DEI are 0, 1 or 'Any'.
Frame Type :
Indicates the type of frame to look for incoming frames. Possible frame types are:
Any: The QCE will match all frame type.
Ethernet: Only Ethernet frames (with Ether Type 0x600-0xFFFF) are allowed.
LLC: Only (LLC) frames are allowed.
SNAP: Only (SNAP) frames are allowed
IPv4: The QCE will match only IPV4 frames.
IPv6: The QCE will match only IPV6 frames.
Action :
Indicates the classification action taken on ingress frame if parameters configured
are matched with the frame's content.
There are three action fields: Class, DPL and DSCP.
Class: Classified QoS Class; if a frame matches the QCE it will be put in the queue.
DPL: Drop Precedence Level; if a frame matches the QCE then DP level will set to
value displayed under DPL column.
264
DSCP: If a frame matches the QCE then DSCP will be classified with the value
displayed under DSCP column.
Modification Buttons :
You can modify each QCE (QoS Control Entry) in the table using the following
buttons:
: Inserts a new QCE before the current row.
: Edits the QCE.
: Moves the QCE up the list.
: Moves the QCE down the list.
: Deletes the QCE.
: The lowest plus sign adds a new entry at the bottom of the QCE listings.
Port Members :
Check the checkbox button in case you what to make any port member of the QCL
entry. By default all ports will be checked
Key Parameters :
Key configuration are described as below:
Tag Value of Tag field can be 'Any', 'Untag' or 'Tag'
VID Valid value of VLAN ID can be any value in the range 1-4095 or 'Any'; user can
enter either a specific value or a range of VIDs
PCP Priority Code Point: Valid value PCP are specific (0, 1, 2, 3, 4, 5, 6, 7) or range
(0-1, 2-3, 4-5, 6-7, 0-3, 4-7) or 'Any'
DEI Drop Eligible Indicator: Valid value of DEI can be any of values between 0, 1 or
'Any'
SMAC Source MAC address: 24 MS bits (OUI) or 'Any'
DMAC Type Destination MAC type: possible values are unicast (UC), multicast (MC),
broadcast (BC) or 'Any'
Frame Type Frame Type can have any of the following values
1. Any
265
2. Ethernet
3. LLC
4. SNAP
5. IPv4
6. IPv6
NOTE: All frame types are explained below:
1. Any: Allow all types of frames.
2. Ethernet: Ethernet Type Valid Ethernet type can have value
within 0x600-0xFFFF or 'Any', default value is 'Any'.
3. LLC: SSAP Address Valid SSAP(Source Service Access Point)
can vary from 0x00 to 0xFF or 'Any', the default value is 'Any'
DSAP Address Valid DSAP(Destination Service Access Point) can
vary from 0x00 to 0xFF or 'Any', the default value is 'Any'
Control Address Valid Control Address can vary from 0x00 to
0xFF or 'Any', the default value is 'Any'
4. SNAP : PID Valid PID(a.k.a Ethernet type) can have value
within 0x00-0xFFFF or 'Any', default value is 'Any'
5. IPv4: Protocol IP protocol number: (0-255, TCP or UDP) or
'Any' Source IP Specific Source IP address in value/mask format
or 'Any'. IP and Mask are in the format x.y.z.w where x, y, z, and w
are decimal numbers between 0 and 255. When Mask is
converted to a 32-bit binary string and read from left to right, all
bits following the first zero must also be zero DSCP Diffserv
Code Point value (DSCP): It can be specific value, range of value
or 'Any'. DSCP values are in the range 0-63 including BE,
CS1-CS7, EF or AF11-AF43
IP Fragment IPv4 frame fragmented option: yes|no|any
Sport Source TCP/UDP port:(0-65535) or 'Any', specific or port
range applicable for IP protocol UDP/TCP
Dport Destination TCP/UDP port:(0-65535) or 'Any', specific or
port range applicable for IP protocol UDP/TCP
6. IPv6 :Protocol IP protocol number: (0-255, TCP or UDP) or
266
'Any'
Source IP IPv6 source address: (a.b.c.d) or 'Any', 32 LS bits
DSCP Diffserv Code Point value (DSCP): It can be specific value,
range of value or 'Any'. DSCP values are in the range 0-63
including BE, CS1-CS7, EF or AF11-AF43
Sport Source TCP/UDP port:(0-65535) or 'Any', specific or port
range applicable for IP protocol UDP/TCP
Dport Destination TCP/UDP port:(0-65535) or 'Any', specific or
port range applicable for IP protocol UDP/TCP
Action Configuration :
Class QoS Class: "class (0-7)", default- basic classification
DP Valid DP Level can be (0-3)", default- basic classification
DSCP Valid dscp value can be (0-63, BE, CS1-CS7, EF or AF11-AF43)
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
267
2-25.12 Storm Control
The section allows user to configure the Storm control for the switch. There is a
unicast storm rate control, multicast storm rate control, and a broadcast storm rate
control. These only affect flooded frames, i.e. frames with a (VLAN ID, DMAC) pair not
present on the MAC Address table. The configuration indicates the permitted packet
rate for unicast, multicast or broadcast traffic across the switch
Web Interface
To configure the Storm Control Configuration parameters in the web interface:
1. Click Configuration, QoS, Storm Control Configuration
2. Evoke to select the frame type to enable storm control
3. Scroll to set the Rate Parameters
4. Click the save to save the setting
5. If you want to cancel the setting then you need to click the Reset button.
It will revert to previously saved values
Figure 2-25.12: The Storm Control Configuration
Parameter description:
Frame Type :
The settings in a particular row apply to the frame type listed here: Unicast,
Multicast or Broadcast.
268
Enable :
Enable or disable the storm control status for the given frame type.
Rate :
The rate unit is packets per second (pps). Valid values are: 1, 2, 4, 8, 16, 32, 64, 128,
256, 512, 1K, 2K, 4K, 8K, 16K, 32K, 64K, 128K, 256K, 512K or 1024K. , 1024K, 2048K,
4096K, 8192K, 16384K or 32768K. , 1024K, 2048K, 4096K, 8192K, 16384K or 32768K.
The 1 kpps is actually 1002.1 pps.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
269
2-26 Mirroring
You can mirror traffic from any source port to a target port for real-time analysis. You
can then attach a logic analyzer or RMON probe to the target port and study the
traffic crossing the source port in a completely unobtrusive manner.
Mirror Configuration is to monitor the traffic of the network. For example, we assume
that Port A and Port B are Monitoring Port and Monitored Port respectively, thus, the
traffic received by Port B will be copied to Port A for monitoring.
Web Interface
To configure the Mirror in the web interface:
1. Click Configuration, Mirroring
2. Scroll to select Port to mirror on which port
3. Scroll to disabled, enable, TX Only and RX only to set the Port mirror mode
4. Click the save to save the setting
5. If you want to cancel the setting then you need to click the Reset button.
It will revert to previously saved values
.
Figure 2-26: The Mirror Configuration
270
271
Parameter description:
Port to mirror on :
Port to mirror also known as the mirror port. Frames from ports that have either
source (rx) or destination (tx) mirroring enabled are mirrored on this port. Disabled
disables mirroring.
Mirror Port Configuration
The following table is used for Rx and Tx enabling.
Port :
The logical port for the settings contained in the same row.
Mode :
Select mirror mode.
Rx only Frames received on this port are mirrored on the mirror port. Frames
transmitted are not mirrored.
Tx only Frames transmitted on this port are mirrored on the mirror port. Frames
received are not mirrored.
Disabled neither frames transmitted nor frames received are mirrored.
Enabled Frames received and frames transmitted are mirrored on the mirror port.
NOTE: For a given port, a frame is only transmitted once. It is
therefore not possible to mirror Tx frames on the mirror port.
Because of this, mode for the selected mirror port is limited to
Disabled or Rx only.
Buttons:
Apply – Click to save changes.
272
Reset- Click to undo any changes made locally and revert to previously saved
values.
273
2-27 UPnP
UPnP is an acronym for Universal Plug and Play. The goals of UPnP are to allow devices
to connect seamlessly and to simplify the implementation of networks in the home
(data sharing, communications, and entertainment) and in corporate environments for
simplified installation of computer components
Web Interface
To configure the UPnP Configuration in the web interface:
1. Click Configuration, UPnP
2. Scroll to select the mode to enable or disable
3. Specify the parameters in each blank field.
4. Click the save to save the setting
5. If you want to cancel the setting then you need to click the Reset button.
It will revert to previously saved values
Figure 2-27: The UPnP Configuration
Parameter description:
These parameters are displayed on the UPnP Configuration page:
Mode :
Indicates the UPnP operation mode. Possible modes are:
Enabled: Enable UPnP mode operation.
Disabled: Disable UPnP mode operation.
274
When the mode is enabled, two ACEs are added automatically to trap UPNP related
packets to CPU. The ACEs are automatically removed when the mode is disabled. .
TTL :
The TTL value is used by UPnP to send SSDP advertisement messages. Valid values
are in the range 1 to 255.
Advertising Duration :
The duration, carried in SSDP packets, is used to inform a control point or control
points how often it or they should receive an SSDP advertisement message from
this switch. If a control point does not receive any message within the duration, it
will think that the switch no longer exists. Due to the unreliable nature of UDP, in
the standard it is recommended that such refreshing of advertisements to be done
at less than one-half of the advertising duration. In the implementation, the switch
sends SSDP messages periodically at the interval one-half of the advertising
duration minus 30 seconds. Valid values are in the range 100 to 86400.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
275
2-28 PTP
This page allows the user to configure and inspect the current PTP clock settings.
Web Interface
To configure the PTP in the web interface:
1. Click Configuration, UPnP
2. Scroll to select the mode to enable or disable
3. Specify the parameters in each blank field.
4. Click the save to save the setting
5. If you want to cancel the setting then you need to click the Reset button.
It will revert to previously saved values
Figure 2-28: The PTP
Parameter description:
PTP External Clock Configuration
One_PPS_Mode
This Selection box will allow you to select the One_pps_mode configuration.
276
The following values are possible:
1. Output : Enable the 1 pps clock output
2. Input : Enable the 1 pps clock input
3. Disable : Disable the 1 pps clock in/out-put
External Enable
This Selection box will allow you to configure the External Clock output.
The following values are possible:
1. True : Enable the external clock output
2. False : Disable the external clock output
Adjust Method
This Selection box will allow you to configure the Frequency adjustment configuration.
1. LTC frequency : Select Local Time Counter (LTC) frequency control
2. SyncE-DPLL : Select SyncE DPLL frequency control, if allowed by SyncE
3. Oscillator : Select an oscillator independent of SyncE for frequency control, if supported
by the HW
4. LTC phase : Select Local Time Counter (LTC) phase control (assumes that the frequency
is locked by means of SyncE)
Clock Frequency
This will allow to set the Clock Frequency.
The possible range of values are 1 - 25000000 (1 - 25MHz)
PTP Clock Configuration
Delete
Check this box and click on 'Save' to delete the clock instance.
Inst
Indicates the Instance of a particular Clock Instance [0..3].
277
Click on the Clock Instance number to edit the Clock details.
ClkDom
Indicates the Clock domain used by the Instance of a particular Clock Instance [0..3].
More instances may use the same clock domain, e.g. a Boundary clock and a Transparent
clock. Only one Slave or Boundary clock is allowed within the same Clock domain.
Device Type
Indicates the Type of the Clock Instance. There are five Device Types.
1. Ord-Bound - clock's Device Type is Ordinary-Boundary Clock.
2. P2p Transp - clock's Device Type is Peer to Peer Transparent Clock.
3. E2e Transp - clock's Device Type is End to End Transparent Clock.
4. Master Only - clock's Device Type is Master Only.
5. Slave Only - clock's Device Type is Slave Only.
Port List
Set check mark for each port configured for this Clock Instance. One port can only be
active within one Clock domain. I.e. enabling a port which is already active in an other
Clock domain is rejected.
2 Step Flag
Static member: defined by the system, true if two-step Sync events and Pdelay_Resp
events are used
Clock Identity
It shows unique clock identifier
One Way
If true, one-way measurements are used. This parameter applies only to a slave. In
one-way mode no delay measurements are performed, i.e. this is applicable only if
frequency synchronization is needed. The master always responds to delay requests.
Protocol
Transport protocol used by the PTP protocol engine
Ethernet PTP over Ethernet multicast
278
EthernetMixed PTP using a combination of Ethernet multicast and unicast
IPv4Multi PTP over IPv4 multicast
IPv4Mixed PTP using a combination of IPv4 multicast and unicast
IPv4Uni PTP over IPv4 unicast
Note : IPv4 unicast protocol only works in Master only and Slave only clocks
See parameter Device Type
In a unicast Slave only clock you also need configure which master clocks
to request Announce and Sync messages from. See: Unicast Slave Configuration
VLAN Tag Enable
Enables the VLAN tagging for the PTP frames.
Note: Packets are only tagged if the port is configured for vlan tagging for the configured
VLAN. I.e the VLAN Tag Enable parameter is ignored
VID
VLAN Identifier used for tagging the PTP frames.
PCP
Priority Code Point value used for PTP frames.
Buttons:
Add New PTP Clock – Click to create a new clock instance.
Apply –Click to save the page immediately.
Reset- Click to reset the the page immediately.
2-29. GVRP
The Generic Attribute Registration Protocol (GARP) provides a generic framework
whereby devices in a bridged LAN, e.g. end stations and switches, can register and
de-register attribute values, such as VLAN Identifiers, with each other. In doing so, the
279
attributes are propagated to devices in the bridged LAN, and these devices form a
¡°reachability¡± tree that is a subset of an active topology. GARP defines the
architecture, rules of operation, state machines and variables for the registration and
de-registration of attribute values.
A GARP participation in a switch or an end station consists of a GARP application
component, and a GARP Information Declaration (GID) component associated with
each port or the switch. The propagation of information between GARP participants
for the same application in a bridge is carried out by the GARP Information
Propagation (GIP) component. Protocol exchanges take place between GARP
participants by means of LLC Type 1 services, using the group MAC address and PDU
format defined for the GARP application concerned.
2-29.1 Global Config
The switch stores its configuration in a number of text files in CLI format. The files are
either virtual (RAM-based) or stored in flash on the switch.
There are three system files:
Running-config: A virtual file that represents the currently active configuration
on the switch. This file is volatile.
Startup-config: The startup configuration for the switch, read at boot time.
Default-config: A read-only file with vendor-specific configuration. This file is
read when the system is restored to default settings.
It is also possible to store up to two other files and apply them to running-config,
thereby switching configuration.
Web Interface
To configure the GVRP in the web interface:
1. Click Configuration, GVRP, Global Config
2. Specify Join-time, Leave-time, Leave All-time, Max VLANs
3. Click Apply
Figure 2-29.1: The GVRP Configuration
280
Enable GVRP globally
The GVRP feature is enabled by setting the check mark in the checkbox named
Enable GVRP.
GVRP protocol timers
Join-time is a value in the range 1-20 in the units of centi seconds, i.e. in units of one
hundredth of a second. The default is 20.
Leave-time is a value in the range 60-300 in the units of centi seconds, i.e. in units of
one hundredth of a second. The default is 60.
Leave All-time is a value in the range 1000-5000 in the units of centi seconds, i.e. in
units of one hundredth of a second. The default is 1000.
Max number of VLANs
When GVRP is enabled a maximum number of VLANs supported by GVRP is specified.
By default this number is 20. This number can only be changed when GVRP is turned off.
281
2-29.2 Port Config
This page allows you to configure the basic GVRP Configuration settings for all switch
ports. The settings relate to the currently selected unit, as reflected by the page
header.
Web Interface
To configure the sFlow Agent in the web interface:
1. Click Configuration, GVRP, Port Config
2. Specify Port, mode
3. Click Apply
Figure 2-29.2: The GVRP Configuration
Parameter description:
GVRP Mode
This configuration is to enable/disable GVRP Mode on particular port locally.
Disable: Select to Disable GVRP mode on this port.
Enable: Select to Enable GVRP mode on this port.
282
2-30. sFlow
The sFlow Collector configuration for the switch can be monitored and modified here.
The configuration is divided into two parts: Configuration of the sFlow receiver (a.k.a.
sFlow collector) and configuration of per-port flow and counter samplers.
sFlow configuration is not persisted to non-volatile memory, which means that a
reboot or master change will disable sFlow sampling.
Web Interface
To configure the sFlow Agent in the web interface:
1. Click Configuration, sFlow
2. Set the parameters
3. Click the save to save the setting
4. If you want to cancel the setting then you need to click the Reset button.
It will revert to previously saved values
.
Figure 2-30: The sFlow Configuration
283
Parameter description:
Agent Configuration
IP Address
The IP address used as Agent IP address in sFlow datagrams. It serves as a unique
key that will identify this agent over extended periods of time.
Both IPv4 and IPv6 addresses are supported.
Receiver Configuration
Owner
Basically, sFlow can be configured in two ways: Through local management using
the Web or CLI interface or through SNMP. This read-only field shows the owner of
the current sFlow configuration and assumes values as follows:
• If sFlow is currently unconfigured/unclaimed, Owner contains <none>.
• If sFlow is currently configured through Web or CLI, Owner contains <Configured
through local management>.
• If sFlow is currently configured through SNMP, Owner contains a string identifying
the sFlow receiver.
If sFlow is configured through SNMP, all controls - except for the Release-button -
are disabled to avoid inadvertent reconfiguration.
The button allows for releasing the current owner and disable sFlow sampling. The
284
button is disabled if sFlow is currently unclaimed. If configured through SNMP, the
release must be confirmed (a confirmation request will appear).
IP Address/Hostname
The IP address or hostname of the sFlow receiver. Both IPv4 and IPv6 addresses are
supported.
UDP Port
The UDP port on which the sFlow receiver listens to sFlow datagrams. If set to 0
(zero), the default port (6343) is used.
Timeout
The number of seconds remaining before sampling stops and the current sFlow
owner is released. While active, the current time left can be updated with a click on
the Refresh-button. If locally managed, the timeout can be changed on the fly
without affecting any other settings.
Max. Datagram Size
The maximum number of data bytes that can be sent in a single sample datagram.
This should be set to a value that avoids fragmentation of the sFlow datagrams.
Valid range is 200 to 1468 bytes with default being 1400 bytes.
Port Configuration
Port
The port number for which the configuration below applies.
Flow Sampler Enabled
Enables/disables flow sampling on this port.
Flow Sampler Sampling Rate
The statistical sampling rate for packet sampling. Set to N to sample on average
1/Nth of the packets transmitted/received on the port.
Not all sampling rates are achievable. If an unsupported sampling rate is requested,
the switch will automatically adjust it to the closest achievable. This will be reported
back in this field.
Flow Sampler Max. Header
The maximum number of bytes that should be copied from a sampled packet to the
285
sFlow datagram. Valid range is 14 to 200 bytes with default being 128 bytes.
If the maximum datagram size does not take into account the maximum header size,
samples may be dropped.
Counter Poller Enabled
Enables/disables counter polling on this port.
Counter Poller Interval
With counter polling enabled, this specifies the interval - in seconds - between
counter poller samples.
Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
2-31 UDLD
This page allows the user to inspect the current UDLD configurations, and possibly
change them as well.
Web Interface
To configure the UDLD in the web interface:
1. Click Configuration, UDLD
2. Specify UDLD mode, Message Interval.
3. Click Apply
.
Figure 2-31: The UDLD
286
Parameter description:
Port
Port number of the switch.
UDLD Mode
Configures the UDLD mode on a port. Valid values
are Disable, Normal and Aggressive. Default mode is Disable.
Disable
In disabled mode, UDLD functionality doesn't exists on port.
Normal
In normal mode, if the link state of the port was determined to be unidirectional, it
will not affect the port state.
Aggressive
In aggressive mode, unidirectional detected ports will get shutdown. To bring back
the ports up, need to disable UDLD on that port.
Message Interval
Configures the period of time between UDLD probe messages on ports that are in
the advertisement phase and are determined to be bidirectional. The range is from
7 to 90 seconds(Default value is 7 seconds)(Currently default time interval is
supported, due to lack of detailed information in RFC 5171).
Buttons:
287
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
2-32 Rapid Ring
This page allows the user to inspect the current Rapid Ring Configuration, and possibly
change them as well
Web Interface
To configure the Rapid Ring in the web interface:
1. Click Configuration, Rapid Ring.
2. Specify the Role, Port, Status.
3. Click Apply.
.
Figure 2-32: The Rapid Ring
Parameter description:
Role Configuration
Role
Set role value.
288
Port
The switch port number of the port.
Status
The current Rapid Ring status of the port.Buttons:
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
2-33 Switch2go
2-33.1 Switch2go setting
Configure Switch2go management and link setting.
Web Interface
To configure Switch2go setting in the web interface:
1. Click Configuration, Switch2go and and Switch2go setting.
2. Set the parameters
3. Click Apply.
Figure 2-33.1: The Switch2go setting
289
Parameter description:
Management mode :
Indicates the Management mode operation. When the mode operation is enabled, the
message will send out to (or get from) the server. The protocol is based on TCP
communication and received on TCP port 443 and the server will send
acknowledgments/information back sender since TCP is a connection-oriented protocol.
Possible modes are:
Enabled: Enable Switch2go Management mode operation.
Disabled: Disable Switch2go Management mode operation.
Server Address :
Indicates the IPv4 host address of server. If the switch provide DNS feature, it also can be a
host name.
Server State :
Report network information between Switch and Server.
Link Option :
Indicates the Link Option operation.
When the Link Option in Automatic, enabling applications to access the services provided by
an UPnP "Internet Gateway Device (IGN)" present on the network.
290
When the Link Option in Manual, you should Setting External Port and Your IGN/NAT's Port
Forward function by Manual.
When Link function working success, Mobile(s) can access this NAT by Internet.
Possible modes are:
Automatic: Link Option in Automatic.
Manual: Link Option in Manual.
Link State :
Report network information between Switch and Internet Gateway Device (IGN).
External Port :
When the Link Option in Manual, you should Setting External Port.
Internal Port :
Information about iSwitch Client's Internal Port.
Protocol :
Information about iSwitch Client's Protocol.
Destination IP :
Information about Client's Destination IP.
2-33.2 iPush Options
iPush options are configurd on this page. User can setup the events to trigger the
iPush and the severity in iPush Event Severity Configuration. The name and role of
each port also can be defined here.
iPush Event Severity Configuration: : Go to event severity configuration page.
Web Interface
To configure iPush Options in the web interface:
1. Click Configuration, Switch2go and iPush Options.
2. Set the parameters
291
3. Click Apply.
Figure 2-33.2: The iPush Options
Parameter description:
Port :
This is the logical port number for this row.
Port Name
Enter up to 47 characters to be descriptive name for identifies this port.
Role
Selects any available role for the given switch port.
Possible role are:
Server - Assign this as Server Port.
Client - Assign this as Client Port.
Buttons:
Apply- Click to apply changes.
292
2-34 SMTP
The function, is used to set a Alarm trap when the switch alarm then you could set the
SMTP server to send you the alarm mail.
Web Interface
To configure the SMTP Configuration in the web interface:
1. Click Configuration, SMTP Configuration
2. Scroll to select the Severity Level
3. Specify the parameters in each blank field.
4. Click the apply to save the setting
5. If you want to cancel the setting then you need to click the Reset button.
It will revert to previously saved values
Figure 2-34: The SMTP Configuration
Parameter description:
293
These parameters are displayed on the SMTP Configuration page:
Mail Server :
Specify the IP Address of the server transferring your email.
Username :
Specify the username on the mail server.
Password :
Specify the password on the mail server.
Severity Level :
Indicates what kind of message will send to mail server. Possible modes are:
<0> Emergency: System is unusable.
<1> Alert: Action must be taken immediately.
<2> Critical: Critical conditions.
<3> Error: Error conditions.
<4> Warning: Warning conditions.
<5> Notice: Normal but significant conditions.
<6> Information: Information messages.
<7> Debug: Debug-level messages.
Sender :
To set the mail sender name.
Return-Path :
To set the mail return-path as sender mail address.
Email Address 1-6 :
Email address that would like to receive the alarm message.
Buttons:
Apply – Click to apply changes.
Reset- Click to undo any changes made locally and revert to previously saved
values.
294
Chapter 3. Monitor
This chapter describes all of the basic network statistics which includes the
Ports, Layer 2 network protocol (e.g. NAS, ACL, DHCP, AAA and RMON etc.)
and any setting of the Switch.
3-1 System
After you login, the switch shows you the system information. This page is default and
tells you the basic information of the system, including “Model Name”, “System
Description”, “Contact”, “Location”, “System Up Time”, “Firmware Version”, “Host Mac
Address”, “Device Port”. With this information, you will know the software version used,
MAC address, serial number, how many ports good and so on. This is helpful while
malfunctioning.
3-1.1 Information
The switch system information is provided here.
Web interface
To configure System Information in the web interface:
1. Click Monitor, System and Information.
2. Check the contact information for the system administrator as well as the name
and location of the switch. Also indicate the local time zone by configuring the
appropriate offset.
3. Click the “Refresh”
295
Figure 3-1.1: System Information
Parameter description:
Model Name
Displays the factory defined model name for identification purpose.
System Description
Displays the system description.
Location
The system location configured in Configuration | System | Information | System
Location.
Contact
The system contact configured in Configuration | System | Information | System
Contact.
Platform Name
Displays the user-defined system name that configured in System | System Information
| Configuration | System Name.
System Date
The current (GMT) system time and date. The system time is obtained through the
296
Timing server running on the switch, if any.
System Uptime
The period of time the device has been operational.
Bootloader Version
Displays the current boot loader version number.
Firmware Version
The software version of this switch.
Hardware-Mechanical Version
The hardware and mechanical version of this switch.
Series Number
The serial number of this switch.
MAC Address
The MAC Address of this switch.
Memory
Displays the memory size of the system.
FLASH
Displays the flash size of the system.
297
3-1.2 IP Status
This page displays the status of the IP protocol layer. The status is defined by the IP
interfaces, the IP routes and the neighbour cache (ARP cache) status.
Web Interface
To display the log configuration in the web interface:
1. Click Monitor, System and IP Status.
2. Display the IP address information.
Figure 3-1.2: The IP Status
298
Parameter description:
IP Interfaces
Interface
Show the name of the interface.
Type
Show the address type of the entry. This may be LINK or IPv4.
Address
Show the current address of the interface (of the given type).
Status
Show the status flags of the interface (and/or address).
IP Routes
Network
Show the destination IP network or host address of this route.
Gateway
Show the gateway address of this route.
Status
Show the status flags of the route.
Neighbour cache
IP Address
Show the IP address of the entry.
Link Address
Show the Link (MAC) address for which a binding to the IP address given exist.
299
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page immediately.
300
3-1.3 Log
This section describes that display the system log information of the switch
Web Interface
To display the log configuration in the web interface:
1. Click Monitor, System and Log.
2. Display the log information.
Figure 3-1.3: The System Log Information
Parameter description:
301
Auto-refresh
To evoke the auto-refresh icon then the device will refresh the log automatically.
Level
level of the system log entry. The following level types are supported:
Information level of the system log.
Warning: Warning level of the system log.
Error: Error level of the system log. All: All levels.
ID
ID (>= 1) of the system log entry.
Time
It will display the log record by device time. The time of the system log entry.
Message
It will display the log detail message. The message of the system log entry.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Updates the system log entries, starting from the current entry ID.
Clear: Flushes the selected log entries.
|<<: Updates the system log entries, starting from the first available entry ID.
<< : Updates the system log entries, ending at the last entry currently displayed.
>> : Updates the system log entries, starting from the last entry currently displayed.
>>|: Updates the system log entries, ending at the last available entry ID
302
3-1.4 Detailed Log
This section describes that display the detailed log information of the switch
Web Interface
To display the detailed log configuration in the web interface:
1. Click Monitor, System and Detailed Log.
2. Display the log information.
Figure 3-1.4: The Detailed System Log Information
Parameter description:
ID
The ID (>= 1) of the system log entry.
Message
The detailed message of the system log entry.
Upper right icon (Refresh, clear…)
You can click them for refresh the system log or clear them by manual, others for
next/up page or entry.
Buttons
303
Refresh: Updates the system log entries, starting from the current entry ID.
|<<: Updates the system log entries to the first available entry ID
<< : Updates the system log entry to the previous available entry ID
>> : Updates the system log entry to the next available entry ID
>>|: Updates the system log entry to the last available entry ID.
304
3-2 Green Ethernet
3-2.1 Port Power Savings
This page provides the current status for EEE.
Web Interface
To display the power Saving in the web interface:
1. Click Monitor, Port Power Savings.
Figure 3-2.1: The Ports States
Parameter description:
Local Port
This is the logical port number for this row.
Link
Shows if the link is up for the port (green = link up, red = link down).
EEE
Shows if EEE is enabled for the port (reflects the settings at the Port Power Savings
configuration page).
LP EEE cap
305
Shows if the link partner is EEE capable.
EEE Savings
Shows if the system is currently saving power due to EEE. When EEE is enabled, the
system will powered down if no frame has been received or transmitted in 5 uSec.
Actiphy Savings
Shows if the system is currently saving power due to ActiPhy.
PerfectReach Savings
Shows if the system is currently saving power due to PerfectReach.
3-3 Ports
The section describes to configure the Port detail parameters of the switch. Others you
could using the Port configure to enable or disable the Port of the switch. Monitor the
ports content or status in the function.
3-3.1 Traffic Overview
The section describes to the Port statistics information and provides overview of general
traffic statistics for all switch ports.
Web Interface
To Display the Port Statistics Overview in the web interface:
1. Click Monitor, Port, then Traffic Overview
2. If you want to auto-refresh then you need to evoke the “Auto-refresh”.
3. Click “ Refresh“ to refresh the port statistics or clear all information when you
click “ Clear”.
Figure 3-3.1: The Port Statistics Overview
306
Parameter description:
Port :
The logical port for the settings contained in the same row.
Packets :
The number of received and transmitted packets per port.
Bytes :
The number of received and transmitted bytes per port.
Errors
The number of frames received in error and the number of incomplete
transmissions per port.
Drops
The number of frames discarded due to ingress or egress congestion.
Filtered
The number of received frames filtered by the forwarding
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
307
occurs every 3 seconds.
Refresh: Click to refresh the page.
Clear: Clears the counters for all ports.
308
3-3.2 Qos Statistics
The section describes that switch could display the QoS detailed Queuing counters for a
specific switch port. for the different queues for all switch ports.
Web Interface
To Display the Queuing Counters in the web interface:
1. Click Monitor, Ports, then QoS Statistics
2. If you want to auto-refresh the information then you need to evoke the
“Auto-refresh”.
3. Click “Refresh” to refresh the Queuing Counters or clear all information when you
click “Clear”.
Figure 3-3.2: The Queuing Counters Overview
Parameter description:
Port :
The logical port for the settings contained in the same row.
Qn :
Qn is the Queue number, There are 8 QoS queues per port. Q0 is the lowest priority
queue.
309
Rx/Tx :
The number of received and transmitted packets per queue.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
Clear: Clears the counters for all ports.
310
3-3.3 QCL Status
The section will let you know how to configure and shows the QCL status
by different QCL users. Each row describes the QCE that is defined. It is a conflict if a
specific QCE is not applied to the hardware due to hardware limitations. The maximum
number of QCEs is 256 on each switch.
Web Interface
To display the QoS Control List Status in the web interface:
1. Click Monitor, Ports, then QCL Status
2. If you want to auto-refresh the information then you need to evoke the
“Auto-refresh”.
3. Scroll to select the combined, static, Voice VLAN and conflict.
4. To click the “Refresh” to refresh an entry of the MVR Statistics Information.
Figure 3-3.3: The QoS Control List Status
Parameter description:
User :
Indicates the QCL user.
QCE#
Indicates the index of QCE.
Frame Type :
Indicates the type of frame to look for incoming frames. Possible frame types are:
311
Any: The QCE will match all frame type.
Ethernet: Only Ethernet frames (with Ether Type 0x600-0xFFFF) are allowed.
LLC: Only (LLC) frames are allowed
LLC: Only (SNAP) frames are allowed.
IPv4: The QCE will match only IPV4 frames.
IPv6: The QCE will match only IPV6 frames.
Port :
Indicates the list of ports configured with the QCE.
Action :
Indicates the classification action taken on ingress frame if parameters configured
are matched with the frame's content.
There are three action fields: Class, DPL and DSCP.
Class: Classified QoS Class; if a frame matches the QCE it will be put in the queue.
DPL: Drop Precedence Level; if a frame matches the QCE then DP level will set to
value displayed under DPL column.
DSCP: If a frame matches the QCE then DSCP will be classified with the value
displayed under DSCP column.
Conflict :
Displays Conflict status of QCL entries. It may happen that resources required to
add a QCE may not available, in that case it shows conflict status as 'Yes', otherwise
it is always 'No’. Please note that conflict can be resolved by releasing the H/W
resources required to add QCL entry on pressing 'Resolve Conflict' button.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Resolve Conflict: Click to release the resources required to add QCL entry, incase
conflict status for any QCL entry is 'yes'.
312
Refresh: Click to refresh the page.
313
3-3.4 Detailed Statistics
The section describes how to provide detailed traffic statistics for a specific switch port.
Use the port select box to select which switch port details to display.
The displayed counters are the totals for receive and transmit, the size counters for
receive and transmit, and the error counters for receive and transmit.
Web Interface
To Display per port detailed Statistics Overview in the web interface:
1. Click Monitor, Ports, then Detailed Port Statistics
2. Scroll the Port Index to select which port you want to show the detailed
3. Port statistics overview”.
4. If you want to auto-refresh the information then you need to evoke the
“Auto-refresh”.
5. Click “Refresh” to refresh the port detailed statistics or clear all information when
you click “Clear”.
Figure 3-3.4: The Detailed Port Statistics
314
Parameter description:
Auto-refresh:
To evoke the auto-refresh to refresh the Port Statistics information automatically.
315
Upper left scroll bar:
To scroll which port to display the Port statistics with “Port-0”, “Port-1...
Receive Total and Transmit Total
Rx and Tx Packets :
The number of received and transmitted (good and bad) packets.
Rx and Tx Octets :
The number of received and transmitted (good and bad) bytes. Includes FCS, but
excludes framing bits.
Rx and Tx Unicast
The number of received and transmitted (good and bad) unicast packets.
Rx and Tx Multicast :
The number of received and transmitted (good and bad) multicast packets.
Rx and Tx Broadcast :
The number of received and transmitted (good and bad) broadcast packets.
Rx and Tx Pause :
A count of the MAC Control frames received or transmitted on this port that have
an opcode indicating a PAUSE operation.
Receive and Transmit Size Counters
The number of received and transmitted (good and bad) packets split into categories
based on their respective frame sizes.
Receive and Transmit Queue Counters
The number of received and transmitted packets per input and output queue.
Receive Error Counters
Rx Drops :
The number of frames dropped due to lack of receive buffers or egress congestion.
Rx CRC/Alignment :
The number of frames received with CRC or alignment errors.
316
Rx Undersize :
The number of short 1 frames received with valid CRC.
Rx Oversize :
The number of long 2 frames received with valid CRC.
Rx Fragments :
The number of short 1 frames received with invalid CRC.
Rx Jabber :
The number of long 2 frames received with invalid CRC.
Rx Filtered :
The number of received frames filtered by the forwarding process.
Short frames are frames that are smaller than 64 bytes.
Long frames are frames that are longer than the configured maximum frame length
for this port.
Transmit Error Counters
Tx Drops :
The number of frames dropped due to output buffer congestion.
Tx Late/Exc. Coll. :
The number of frames dropped due to excessive or late collisions.
Auto-refresh:
To evoke the auto-refresh to refresh the Queuing Counters automatically.
Upper right icon (Refresh, clear)
You can click them for refresh the Port Detail Statistics or clear them by manual.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
317
occurs every 3 seconds.
Clear: Clears the counters for the selected port.
Refresh: Click to refresh the page.
3-3.5 SFP Information
This page displays general SFP information and monitoring information.
Web Interface
To Display the SFP information in the web interface:
1. Click Monitor, Ports, then SFP Information
2. To display the SFP Information.
Figure 3-3.5: The SFP Information Overview
Parameter description:
Port
The logical port for the settings contained in the same row.
Tx Central Wavelength
Displays the nominal transmitter output wavelength in nm.
Bit rate
318
Displays the nominal bit rate of the transceiver.
Temperature
Displays the internally measured transceiver temperature. Temperature accuracy is
vendor specific but must be better than 3 degrees Celsius over specified operating
temperature and voltage.
Vcc
Displays the internally measured transceiver supply voltage. Accuracy is vendor
specific but must be better than 3 percent of the manufacturer's nominal value over
specified operating temperature and voltage. Note that in some transceivers,
transmitter supply voltage and receiver supply voltage are isolated. In that case,
only one supply is monitored. Refer to the device specification for more detail.
Mon1 (Bias)
Displays the measured TX bias current in uA. Accuracy is vendor specific but must
be better than 10 percent of the manufacturer's nominal value over specified
operating temperature and voltage.
Mon2 (TX PWR)
Displays the measured coupled TX output power in mW. Accuracy is vendor specific
but must be better than 3dB over specified operating temperature and voltage.
Data is assumed to be based on measurement of a laser monitor photodiode
current. Data is not valid when the transmitter is disabled.
Mon3 (RX PWR)
Displays the measured received optical power in mW. Absolute accuracy is
dependent upon the exact optical wavelength. For the vendor specified wavelength,
accuracy should be better than 3dB over specified temperature and voltage. This
accuracy should be maintained for input power levels up to the lesser of maximum
transmitted or maximum received optical power per the appropriate standard. It
should be maintained down to the minimum transmitted power minus cable plant
loss (insertion loss or passive loss) per the appropriate standard. Absolute accuracy
beyond this minimum required received input optical power range is vendor
specific.
Buttons
319
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Clear: Clears the counters for the selected port.
Refresh: Click to refresh the page.
320
3-3.6 SFP Detail Info
This page displays general SFP information and monitoring information.
Web Interface
To configure the SFP Detail Info in the web interface:
1. Click Monitor, Port and SFP Detail Info.
2. To display the SFP Information.
Figure 3-3.6: The SFP Detail Info
Parameter description:
Connector Type
Displays the external optical or electrical cable connector provided as the media
interface.
Fiber Type
Displays the fiber channel transmission media.
Tx Central Wavelength
Displays the nominal transmitter output wavelength in nm.
Bit rate
321
Displays the nominal bit rate of the transceiver.
Vendor OUI
Displays the vendor IEEE company ID.
Vendor Name
Displays the vendor name.
Vendor P/N
Displays the vendor part number or product name.
Vendor Revision
Displays the vendor¡¦s product revision.
Vendor Serial Number
Displays the vendor serial number for the transceiver.
Date Code
Displays the vendor's manufacturing date code.
Temperature
Displays the internally measured transceiver temperature. Temperature accuracy is
vendor specific but must be better than 3 degrees Celsius over specified operating
temperature and voltage.
Vcc
Displays the internally measured transceiver supply voltage. Accuracy is vendor
specific but must be better than 3 percent of the manufacturer's nominal value over
specified operating temperature and voltage. Note that in some transceivers,
transmitter supply voltage and receiver supply voltage are isolated. In that case,
only one supply is monitored. Refer to the device specification for more detail.
Mon1 (Bias)
Displays the measured TX bias current in uA. Accuracy is vendor specific but must
be better than 10 percent of the manufacturer's nominal value over specified
operating temperature and voltage.
Mon2 (TX PWR)
322
Displays the measured coupled TX output power in mW. Accuracy is vendor specific
but must be better than 3dB over specified operating temperature and voltage.
Data is assumed to be based on measurement of a laser monitor photodiode
current. Data is not valid when the transmitter is disabled.
Mon3 (RX PWR)
Displays the measured received optical power in mW. Absolute accuracy is
dependent upon the exact optical wavelength. For the vendor specified wavelength,
accuracy should be better than 3dB over specified temperature and voltage. This
accuracy should be maintained for input power levels up to the lesser of maximum
transmitted or maximum received optical power per the appropriate standard. It
should be maintained down to the minimum transmitted power minus cable plant
loss (insertion loss or passive loss) per the appropriate standard. Absolute accuracy
beyond this minimum required received input optical power range is vendor
specific.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Clear: Clears the counters for the selected port.
Refresh: Click to refresh the page.
3-4 Link OAM
3-4.1 Statistics
This page provides detailed OAM traffic statistics for a specific switch port. Use the port
select box to select which switch port details to display.
The displayed counters represent the total number of OAM frames received and
transmitted for the selected port. Discontinuities of these counter can occur at
re-initialization of the management system.
323
Web Interface
To configure the Statistics in the web interface:
1. Click Monitor, Link OAM and Statistics.
2. To display the Statistics.
Figure 3-4.1: The Statistics
Parameter description:
Receive Total and Transmit Total
Rx and Tx OAM Information PDU's
The number of received and transmitted OAM Information PDU's. Discontinuities of
this counter can occur at re-initialization of the management system.
Rx and Tx Unique Error Event Notification
A count of the number of unique Event OAMPDUs received and transmitted on this
interface. Event Notifications may be sent in duplicate to increase the probability of
successfully being received, given the possibility that a frame may be lost in transit.
Duplicate Event Notification transmissions are counted by Duplicate Event
Notification counters for Tx and Rx respectively. A unique Event Notification
OAMPDU is indicated as an Event Notification OAMPDU with a Sequence Number
field that is distinct from the previously transmitted Event Notification OAMPDU
Sequence Number.
324
Rx and Tx Duplicate Error Event Notification
A count of the number of duplicate Event OAMPDUs received and transmitted on
this interface. Event Notification OAMPDUs may be sent in duplicate to increase the
probability of successfully being received, given the possibility that a frame may be
lost in transit. A duplicate Event Notification OAMPDU is indicated as an Event
Notification OAMPDU with a Sequence Number field that is identical to the
previously transmitted Event Notification OAMPDU Sequence Number.
Rx and Tx Loopback Control
A count of the number of Loopback Control OAMPDUs received and transmitted on
this interface.
Rx and Tx Variable Request
A count of the number of Variable Request OAMPDUs received and transmitted on
this interface.
Rx and Tx Variable Response
A count of the number of Variable Response OAMPDUs received and transmitted
on this interface.
Rx and Tx Org Specific PDU's
A count of the number of Organization Specific OAMPDUs transmitted on this
interface.
Rx and Tx Unsupported Codes
A count of the number of OAMPDUs transmitted on this interface with an
unsupported op-code.
Rx and Tx Link fault PDU's
A count of the number of Link fault PDU's received and transmitted on this
interface.
Rx and Tx Dying Gasp
A count of the number of Dying Gasp events received and transmitted on this
interface.
Rx and Tx Critical Event PDU's
A count of the number of Critical event PDU's received and transmitted on this
325
interface.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Clear: Clears the counters for the selected port.
Refresh: Click to refresh the page.
3-4.2 Port Status
This page provides Link OAM configuration operational status.
The displayed fields shows the active configuration status for the selected port.
Web Interface
To configure the Port Status in the web interface:
1. Click Monitor, Link OAM and Port Status.
2. To display the Port Status.
Figure 3-4.2: The Port Status
326
Parameter description:
Local and Peer
Mode
The Mode in which the Link OAM is operating, Active or Passive.
Unidirectional Operation Support
This feature is not available to be configured by the user. The status of this
configuration is retrieved from the PHY.
Remote Loopback Support
If status is enabled, DTE is capable of OAM remote loopback mode.
Link Monitoring Support
If status is enabled, DTE supports interpreting Link Events.
MIB Retrieval Support
If status ie enabled DTE supports sending Variable Response OAMPDUs.
MTU Size
It represents the largest OAMPDU, in octets, supported by the DTE. This value is
compared to the remotes Maximum PDU Size and the smaller of the two is used.
Multiplexer State
When in forwarding state, the Device is forwarding non-OAMPDUs to the lower
327
sublayer. Incase of discarding, the device discards all the non-OAMPDU's.
Parser State
When in forwarding state, Device is forwarding non-OAMPDUs to higher sublayer.
When in loopback, Device is looping back non-OAMPDUs to the lower sublayer.
When in discarding state, Device is discarding non-OAMPDUs.
Organizational Unique Identification
24-bit Organizationally Unique Identifier of the vendor.
PDU Revision
It indicates the current revision of the Information TLV. The value of this field shall
start at zero and be incremented each time something in the Information TLV
changes. Upon reception of an Information TLV from a peer, an OAM client may use
this field to decide if it needs to be processed (an Information TLV that is identical
to the previous Information TLV doesn't need to be parsed as nothing in it has
changed).
PDU Permission
This field is available only for the Local DTE. It displays the current permission rules
set for the local DTE. Possible values are "Link fault","Receive only", "Information
exchange only","ANY".
Discovery State
Displays the current state of the discovery process. Possible states are Fault state,
Active state, Passive state, SEND_LOCAL_REMOTE_STATE,
SEND_LOCAL_REMOTE_OK_STATE, SEND_ANY_STATE.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
3-4.3 Event Status
This page allows the user to inspect the current Link OAM Link Event configurations, and
change them as well.
The left pane displays the Event status for the Local OAM unit while the right pane
displays the status for the Peer for the respective port.
Web Interface
To configure the Event Status in the web interface:
328
1. Click Monitor, Link OAM and Event Status.
2. To display the Event Status.
Figure 3-4.1: The Event Status
Parameter description:
Port
The switch port number.
Sequence Number
This two-octet field indicates the total number of events occurred at the remote
end.
Frame Error Event Timestamp
This two-octet field indicates the time reference when the event was generated, in
terms of 100 ms intervals.
Frame error event window
This two-octet field indicates the duration of the period in terms of 100 ms intervals.
1) The default value is one second. 2) The lower bound is one second. 3) The upper
bound is one minute.
Frame error event threshold
329
This four-octet field indicates the number of detected errored frames in the period
is required to be equal to or greater than in order for the event to be generated. 1)
The default value is one frame error. 2) The lower bound is zero frame errors. 3) The
upper bound is unspecified.
Frame errors
This four-octet field indicates the number of detected errored frames in the period.
Total frame errors
This eight-octet field indicates the sum of errored frames that have been detected
since the OAM sublayer was reset.
Total frame error events
This four-octet field indicates the number of Errored Frame Event TLVs that have
been generated since the OAM sublayer was reset.
Frame Period Error Event Timestamp
This two-octet field indicates the time reference when the event was generated, in
terms of 100 ms intervals.
Frame Period Error Event Window
This four-octet field indicates the duration of period in terms of frames.
Frame Period Error Event Threshold
This four-octet field indicates the number of errored frames in the period is required
to be equal to or greater than in order for the event to be generated.
Frame Period Errors
This four-octet field indicates the number of frame errors in the period.
Total frame period errors
This eight-octet field indicates the sum of frame errors that have been detected
since the OAM sublayer was reset.
Total frame period error events
This four-octet field indicates the number of Errored Frame Period Event TLVs that
have been generated since the OAM sublayer was reset.
Symbol Period Error Event Timestamp
This two-octet field indicates the time reference when the event was generated, in
terms of 100 ms intervals.
Symbol Period Error Event Window
This eight-octet field indicates the number of symbols in the period.
Symbol Period Error Event Threshold
This eight-octet field indicates the number of errored symbols in the period is
required to be equal to or greater than in order for the event to be generated.
Symbol Period Errors
This eight-octet field indicates the number of symbol errors in the period.
Symbol frame period errors
This eight-octet field indicates the sum of symbol errors since the OAM sublayer
was reset.
330
Symbol frame period error events
This four-octet field indicates the number of Errored Symbol Period Event TLVs that
have been generated since the OAM sublayer was reset.
Event Seconds Summary Time Stamp
This two-octet field indicates the time reference when the event was generated, in
terms of 100 ms intervals, encoded as a 16-bit unsigned integer.
Event Seconds Summary Window
This two-octet field indicates the duration of the period in terms of 100 ms intervals,
encoded as a 16-bit unsigned integer.
Event Seconds Summary Threshold
This two-octet field indicates the number of errored frame seconds in the period is
required to be equal to or greater than in order for the event to be generated,
encoded as a 16-bit unsigned integer.
Event Seconds Summary Events
This two-octet field indicates the number of errored frame seconds in the period,
encoded as a 16-bit unsigned integer.
Event Seconds Summary Error Total
This four-octet field indicates the sum of errored frame seconds that have been
detected since the OAM sublayer was reset.
Event Seconds Summary Event Total
This four-octet field indicates the number of Errored Frame Seconds Summary
Event TLVs that have been generated since the OAM sublayer was reset, encoded as
a 32bit unsigned integer.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
3-5 DHCP
3-5.1 Server
DHCP Server is used to allocate network addresses and deliver configuration
parameters to dynamically configured hosts called DHCP client.
331
3-5.1.1 Statistics
This page displays the database counters and the number of DHCP messages sent and
received by DHCP server.
Web Interface
Display the DHCP server Statistics Overview in the web interface:
Click Protocol -based VLAN configuration and add new entry.
Figure 3-5.1.1: The Protocol to Group Mapping Table
Parameter description:
Database Counters
Pool :
Number of pools.
Excluded IP Address :
332
Number of excluded IP address ranges.
Declined IP Address :
Number of sec lined IP addresses.
Database Counters
Automatic Binding :
Number of bindings with network-type pools.
Manual Binding :
Number of bindings that administrator assigns an IP address to a client. That is, the
pool is of host type.
Expired Binding :
Number of bindings that their lease time expired or they are cleared from
Automatic/Manual type bindings.
DHCP Message Received Counters
DISCOVER :
Number of DHCP DISCOVER messages received.
REQUEST :
Number of DHCP REQUEST messages received.
DECLINE :
Number of DHCP DECLINE messages received.
RELEASE :
Number of DHCP RELEASE messages received.
INFORM :
Number of DHCP INFORM messages received.
DHCP Message Sent Counters
OFFER :
Number of DHCP OFFER messages sent.
333
ACK :
Number of DHCP ACK messages sent.
NAK :
Number of DHCP NAK messages sent.
3-5.1.2 Binding
This page displays bindings generated for DHCP clients.
Web Interface
To Display DHCP Server Binding IP in the web interface:
Click DHCP, Server and Binding.
Figure 3-5.1.2: The Group Name of VLAN Mapping Table
Parameter description:
IP :
IP address allocated to DHCP client.
Type :
Type of binding. Possible types are Automatic, Manual, and Expired.
State :
State of binding. Possible states are Committed, Allocated, and Expired.
Pool Name :
334
The pool that generates the binding.
Server ID :
Server IP address to service the binding.
3-5.1.3 Declined IP
This page displays declined IP addresses.
Web Interface
To Display DHCP Server Declined IP in the web interface:
Click DHCP, Server and Declined IP.
Figure 3-5.1.3: The Declined IP
Parameter description:
IP :
IP address allocated to DHCP client.
Type :
Type of binding. Possible types are Automatic, Manual, and Expired.
State :
State of binding. Possible states are Committed, Allocated, and Expired.
Pool Name :
The pool that generates the binding.
335
Server ID :
Server IP address to service the binding.
336
3-5.2 Snooping Table
This page display the dynamic IP assigned information after DHCP Snooping mode is
disabled. All DHCP clients obtained the dynamic IP address from the DHCP server will
be listed in this table except for local VLAN interface IP addresses. Entries in the
Dynamic DHCP snooping Table are shown on this page.
Web Interface
To monitor a DHCP in the web interface:
1. Click Monitor, DHCP, and Snooping table
2. Checked “Auto-refresh”.
3. Click “Refresh” to refresh the port detailed statistics or clear all
information when you click “Clear”.
Figure 3-5.2: The DHCP snooping table
Parameter description:
MAC Address :
User MAC address of the entry.
VLAN ID :
VLAN-ID in which the DHCP traffic is permitted.
Source Port:
Switch Port Number for which the entries are displayed.
IP Address :
User IP address of the entry.
IP Subnet Mask :
337
User IP subnet mask of the entry.
DHCP Server Address :
DHCP Server address of the entry.
338
3-5.3 Relay Statistics
This page provides statistics for DHCP relay.
Web Interface
To monitor a DHCP Relay statistics in the web interface:
4. Click Monitor, DHCP, Relay Statistics
5. Checked “Auto-refresh”.
6. Click “Refresh” to refresh the port detailed statistics or clear all
information when you click “Clear”.
Figure 3-5.3: The DHCP relay statistics
Parameter description:
Server Statistics
Transmit to Server :
The number of packets that are relayed from client to server.
Transmit Error :
The number of packets that resulted in errors while being sent to clients.
339
Receive from Server :
The number of packets received from server.
Receive Missing Agent Option:
The number of packets received without agent information options.
Receive Missing Circuit ID :
The number of packets received with the Circuit ID option missing.
Receive Missing Remote ID :
The number of packets received with the Remote ID option missing.
Receive Bad Circuit ID:
The number of packets whose Circuit ID option did not match known circuit ID.
Receive Bad Remote ID :
The number of packets whose Remote ID option did not match known Remote ID.
Client Statistics
Transmit to Client :
The number of relayed packets from server to client.
Transmit Error :
The number of packets that resulted in error while being sent to servers.
Receive from Client :
The number of received packets from server.
Receive Agent Option :
The number of received packets with relay agent information option.
Replace Agent Option :
The number of packets which were replaced with relay agent information option.
Keep Agent Option :
The number of packets whose relay agent information was retained.
Drop Agent Option :
340
The number of packets that were dropped which were received with relay agent information.
341
3-5.4 Detailed Statistics
This page provides statistics for DHCP snooping. Notice that the normal forward
per-port TX statistics isn't increased if the incoming DHCP packet is done by L3
forwarding mechanism. And clear the statistics on specific port may not take effect on
global statistics since it gathers the different layer overview.
Web Interface
To monitor an DHCP Relay statistics in the web interface:
1. Click Monitor, DHCP, Detailed Statistics
2. Checked “Auto-refresh”.
3. Click “Refresh” to refresh the port detailed statistics or clear all
information when you click “Clear”.
Figure 3-5.4: The DHCP Detailed Statistics
342
Parameter description:
Server Statistics
Rx and Tx Discover :
The number of discover (option 53 with value 1) packets received and transmitted.
Rx and Tx Offer :
The number of offer (option 53 with value 2) packets received and transmitted.
Rx and Tx Request :
The number of request (option 53 with value 3) packets received and transmitted.
Rx and Tx Decline:
The number of decline (option 53 with value 4) packets received and transmitted.
Rx and Tx ACK:
The number of ACK (option 53 with value 5) packets received and transmitted.
Rx and Tx NAK:
The number of NAK (option 53 with value 6) packets received and transmitted.
Rx and Tx Release:
The number of release (option 53 with value 7) packets received and transmitted.
Rx and Tx Inform:
The number of inform (option 53 with value 8) packets received and transmitted.
Rx and Tx Lease Query:
The number of lease query (option 53 with value 10) packets received and transmitted.
Rx and Tx Lease Unassigned:
The number of lease unassigned (option 53 with value 11) packets received and transmitted.
Rx and Tx Lease Unknown:
The number of lease unknown (option 53 with value 12) packets received and transmitted. Rx
and Tx Lease Active
Rx and Tx Lease Active:
343
The number of lease active (option 53 with value 13) packets received and transmitted.
Rx Discarded checksum error:
The number of discard packet that IP/UDP checksum is error.
Rx Discarded from Untrusted:
The number of discarded packet that are coming from untrusted port.
344
3-6 Security
3-6.1 Access Management Statistics
This page provides statistics for access management.
Web Interface
To configure an Assess Management Statistics in the web interface:
1. Click Security, Access Management Statistics.
2. Checked “Auto-refresh”.
3. Click “Refresh” to refresh the port detailed statistics or clear all information when
you click “Clear”.
Figure 3-6.1: The Access Management Statistics
Parameter description:
Interface :
The interface type through which the remote host can access the switch.
Received Packets :
Number of received packets from the interface when access management mode is
enabled.
345
Allowed Packets :
Number of allowed packets from the interface when access management mode is
enabled
Discarded Packets. :
Number of discarded packets from the interface when access management mode is
enabled.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
Clear: Clears the counters for the selected port.
3-6.2 Network
3-6.2.1 Port Security
3-6.2.1.1 Switch
This page shows the Port Security status. Port Security is a module with no direct
configuration. Configuration comes indirectly from other modules - the user modules.
When a user module has enabled port security on a port, the port is set-up for
software-based learning. In this mode, frames from unknown MAC addresses are passed
on to the port security module, which in turn asks all user modules whether to allow this
new MAC address to forward or block it. For a MAC address to be set in the forwarding
state, all enabled user modules must unanimously agree on allowing the MAC address to
forward. If only one chooses to block it, it will be blocked until that user module decides
otherwise.
The status page is divided into two sections - one with a legend of user modules and one
with the actual port status.
Web Interface
To configure a Port Security Switch Status Configuration in the web interface:
346
1. Click Security, Network, Port Security, then Switch
2. Checked “Auto-refresh”.
3. Click “Refresh” to refresh the port detailed statistics.
Figure 3-6.2.1.1: The Port Security Switch Status
Parameter description:
User Module Legend
The legend shows all user modules that may request Port Security services.
User Module Name
The full name of a module that may request Port Security services.
Abbr
A one-letter abbreviation of the user module. This is used in the Users column in
the port status table.
Port Status
The table has one row for each port on the switch and a number of columns, which
347
are:
Port
The port number for which the status applies. Click the port number to see the
status for this particular port.
Users
Each of the user modules has a column that shows whether that module has
enabled Port Security or not. A '-' means that the corresponding user module is not
enabled, whereas a letter indicates that the user module abbreviated by that letter
(see Abbr) has enabled port security.
State
Shows the current state of the port. It can take one of four values:
Disabled: No user modules are currently using the Port Security service.
Ready: The Port Security service is in use by at least one user module, and is
awaiting frames from unknown MAC addresses to arrive.
Limit Reached: The Port Security service is enabled by at least the Limit Control user
module, and that module has indicated that the limit is reached and no more MAC
addresses should be taken in.
Shutdown: The Port Security service is enabled by at least the Limit Control user
module, and that module has indicated that the limit is exceeded. No MAC
addresses can be learned on the port until it is administratively re-opened on the
Limit Control configuration Web-page.
MAC Count (Current, Limit)
The two columns indicate the number of currently learned MAC addresses
(forwarding as well as blocked) and the maximum number of MAC addresses that
can be learned on the port, respectively.
If no user modules are enabled on the port, the Current column will show a dash (-).
If the Limit Control user module is not enabled on the port, the Limit column will
show a dash (-).
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
348
3-6.2.1.2 Port
This section shows the MAC addresses secured by the Port Security module. Port
Security is a module with no direct configuration. Configuration comes indirectly from
other modules - the user modules. When a user module has enabled port security on a
port, the port is set-up for software-based learning. In this mode, frames from
unknown MAC addresses are passed on to the port security module, which in turn asks
all user modules whether to allow this new MAC address to forward or block it. For a
MAC address to be set in the forwarding state, all enabled user modules must
unanimously agree on allowing the MAC address to forward. If only one chooses to
block it, it will be blocked until that user module decides otherwise.
Web Interface
To configure a Port Security Switch Status Configuration in the web interface:
1. Click Security, Network, Port Security, and then Port.
2. Specify the Port which you want to monitor.
3. Checked “Auto-refresh”.
4. Click “Refresh” to refresh the port detailed statistics.
Figure 3-6.2.1.2: The Port Security Port Status
Parameter description:
349
MAC Address & VLAN ID :
The MAC address and VLAN ID that is seen on this port. If no MAC addresses are
learned, a single row stating "No MAC addresses attached" is displayed.
State :
Indicates whether the corresponding MAC address is blocked or forwarding. In the
blocked state, it will not be allowed to transmit or receive traffic.
Time of Addition :
Shows the date and time when this MAC address was first seen on the port.
Age/Hold :
If at least one user module has decided to block this MAC address, it will stay in the
blocked state until the hold time (measured in seconds) expires. If all user modules
have decided to allow this MAC address to forward, and aging is enabled, the Port
Security module will periodically check that this MAC address still forwards traffic. If
the age period (measured in seconds) expires and no frames have been seen, the
MAC address will be removed from the MAC table. Otherwise a new age period will
begin.
If aging is disabled or a user module has decided to hold the MAC address
indefinitely, a dash (-) will be shown.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
350
3-6.2.2 NAS
3-6.2.2.1 Switch
The section describes to show the each port NAS status information of the switch. The
status includes Admin State Port State, Last Source, Last ID, QoS Class, and Port VLAN
ID.
Web Interface
To configure a NAS Switch Status Configuration in the web interface:
1. Click Security, Network, NAS, and then Port.
2. Checked “Auto-refresh”.
3. Click “Refresh” to refresh the port detailed statistics.
Figure 3-6.2.2.1: The Network Access Server Switch Status
Parameter description:
Port :
The switch port number. Click to navigate to detailed NAS statistics for this port.
Admin State :
The port's current administrative state. Refer to NAS Admin State for a description
351
of possible values.
Port State :
The current state of the port. Refer to NAS Port State for a description of the
individual states.
Last Source :
The source MAC address carried in the most recently received EAPOL frame for
EAPOL-based authentication, and the most recently received frame from a new
client for MAC-based authentication.
Last ID :
The user name (supplicant identity) carried in the most recently received Response
Identity EAPOL frame for EAPOL-based authentication, and the source MAC address
from the most recently received frame from a new client for MAC-based
authentication.
QoS Class :
QoS Class assigned to the port by the RADIUS server if enabled.
Port VLAN ID :
The VLAN ID that NAS has put the port in. The field is blank, if the Port VLAN ID is
not overridden by NAS.
If the VLAN ID is assigned by the RADIUS server, "(RADIUS-assigned)" is appended
to the VLAN ID. Read more about RADIUS-assigned VLANs here.
If the port is moved to the Guest VLAN, "(Guest)" is appended to the VLAN ID. Read
more about Guest VLANs here.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
352
3-6.2.2.2 Port
The section describes to provide detailed NAS statistics for a specific switch port
running EAPOL-based IEEE 802.1X authentication. For MAC-based ports, it shows selected
backend server (RADIUS Authentication Server) statistics, only.
Web Interface
To configure a NAS Port Status Configuration in the web interface:
1. Click Security, Network, NAS, and then Port.
2. Checked “Auto-refresh”.
3. Click “Refresh” to refresh the port detailed statistics.
Figure 3-6.2.2.2: The NAS Statistics
Parameter description:
Port State
Admin State :
The port's current administrative state. Refer to NAS Admin State for a description
of possible values.
Port State :
The current state of the port. Refer to NAS Port State for a description of the
individual states.
353
QoS Class :
The QoS class assigned by the RADIUS server. The field is blank if no QoS class is
assigned.
Port VLAN ID :
The VLAN ID that NAS has put the port in. The field is blank, if the Port VLAN ID is
not overridden by NAS.
If the VLAN ID is assigned by the RADIUS server, "(RADIUS-assigned)" is appended
to the VLAN ID. Read more about RADIUS-assigned VLANs here.
If the port is moved to the Guest VLAN, "(Guest)" is appended to the VLAN ID. Read
more about Guest VLANs here.
Port Counters
EAPOL Counters :
These supplicant frame counters are available for the following administrative
states:
• Force Authorized
• Force Unauthorized
• Port-based 802.1X
• Single 802.1X
• Multi 802.1X
Backend Server Counters :
These backend (RADIUS) frame counters are available for the following
administrative states:
• Port-based 802.1X
• Single 802.1X
• Multi 802.1X
• MAC-based Auth.
Last Supplicant/Client Info :
Information about the last supplicant/client that attempted to authenticate. This
354
information is available for the following administrative states:
• Port-based 802.1X
• Single 802.1X
• Multi 802.1X
• MAC-based Auth.
Selected Counters
Selected Counters :
The Selected Counters table is visible when the port is in one of the following
administrative states:
• Multi 802.1X
• MAC-based Auth.
The table is identical to and is placed next to the Port Counters table, and will be
empty if no MAC address is currently selected. To populate the table, select one of
the attached MAC Addresses from the table below.
Attached MAC Addresses
Identity :
Shows the identity of the supplicant, as received in the Response Identity EAPOL
frame.
Clicking the link causes the supplicant's EAPOL and Backend Server counters to be
shown in the Selected Counters table. If no supplicants are attached, it shows No
supplicants attached.
This column is not available for MAC-based Auth.
MAC Address :
For Multi 802.1X, this column holds the MAC address of the attached supplicant.For
MAC-based Auth., this column holds the MAC address of the attached client.
Clicking the link causes the client's Backend Server counters to be shown in the
Selected Counters table. If no clients are attached, it shows No clients attached.
VLAN ID
This column holds the VLAN ID that the corresponding client is currently secured
355
through the Port Security module.
State :
The client can either be authenticated or unauthenticated. In the authenticated
state, it is allowed to forward frames on the port, and in the unauthenticated state,
it is blocked. As long as the backend server hasn't successfully authenticated the
client, it is unauthenticated. If an authentication fails for one or the other reason, the
client will remain in the unauthenticated state for Hold Time seconds.
Last Authentication :
Shows the date and time of the last authentication of the client (successful as well
as unsuccessful).
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
Clear: This button is available in the following modes:
• Force Authorized
• Force Unauthorized
• Port-based 802.1X
• Single 802.1X
Clear All: Click to clear the counters for the selected port.
This button is available in the following modes:
• Multi 802.1X
• MAC-based Auth.X
Clear This: Click to clear both the port counters and all of the attached client's
counters. The "Last Client" will not be cleared, however.
This button is available in the following modes:
• Multi 802.1X
• MAC-based Auth.X
356
Click to clear only the currently selected client's counters.
357
3-6.2.3 ACL Status
The section describes how to shows the ACL status by different ACL users. Each row
describes the ACE that is defined. It is a conflict if a specific ACE is not applied to the
hardware due to hardware limitations. The maximum number of ACEs is 512 on each
switch.
Web Interface
To display the ACL status in the web interface:
1. Click Monitor, Network, and then ACL status
2. If you want to auto-refresh the information then you need to evoke the
“Auto-refresh”.
3. Click “Refresh“ to refresh the ACL Status
Figure 3-6.2.3: The ACL Rate Limiter Configuration
Parameter description:
User :
Indicates the ACL user.
Ingress Port :
Indicates the ingress port of the ACE. Possible values are:
358
All: The ACE will match any ingress port.
Port: The ACE will match a specific ingress port.
Frame Type :
Indicates the frame type of the ACE. Possible values are:
Any: The ACE will match any frame type.
EType: The ACE will match Ethernet Type frames. Note that an Ethernet Type based
ACE will not get matched by IP and ARP frames.
ARP: The ACE will match ARP/RARP frames.
IPv4: The ACE will match all IPv4 frames.
IPv4: The ACE will match all IPv4 frames.
IPv4/ICMP: The ACE will match IPv4 frames with ICMP protocol.
IPv4/UDP: The ACE will match IPv4 frames with UDP protocol.
IPv4/TCP: The ACE will match IPv4 frames with TCP protocol.
IPv4/Other: The ACE will match IPv4 frames, which are not ICMP / UDP / TCP.
IPv6: The ACE will match all IPv6 standard frames.
Action :
Indicates the forwarding action of the ACE.
Permit: Frames matching the ACE may be forwarded and learned.
Deny: Frames matching the ACE are dropped.
Filter: Frames matching the ACE are filtered.
Rate Limiter :
Indicates the rate limiter number of the ACE. The allowed range is 1 to 16. When
Disabled is displayed, the rate limiter operation is disabled.
Port Redirect :
Indicates the port copy operation of the ACE. Frames matching the ACE are copied
to the port number. The allowed values are Disabled or a specific port number.
When Disabled is displayed, the port copy operation is disabled.
359
CPU :
Forward packet that matched the specific ACE to CPU.
CPU Once :
Forward first packet that matched the specific ACE to CPU.
Counter :
The counter indicates the number of times the ACE was hit by a frame.
Conflict :
Indicates the hardware status of the specific ACE. The specific ACE is not applied to
the hardware due to hardware limitations.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
360
3-6.2.4 ARP Inspection
The section describes to configure the Dynamic ARP Inspection Table parameters of
the switch. The Dynamic ARP Inspection Table contains up to 1024 entries, and is
sorted first by port, then by VLAN ID, then by MAC address, and then by IP address.
Web Interface
To configure a Dynamic ARP Inspection Table Configuration in the web interface:
1. Click Security, Network, ARP Inspection.
2. Checked “Auto-refresh”.
3. Click “Refresh” to refresh the port detailed statistics.
4. Specify the Start from port, VLAN ID, MAC Address, IP Address, and entries per
page.
.
Figure 3-6.2.4: The Dynamic ARP Inspection Table
Parameter description:
Navigating the ARP Inspection Table:
Each page shows up to 99 entries from the Dynamic ARP Inspection table, default being 20,
selected through the "entries per page" input field. When first visited, the web page will show
the first 20 entries from the beginning of the Dynamic ARP Inspection Table.
The "Start from port address", "VLAN", "MAC address" and "IP address" input fields allow the
user to select the starting point in the Dynamic ARP Inspection Table. Clicking the button will
update the displayed table starting from that or the closest next Dynamic ARP Inspection Table
361
match. In addition, the two input fields will - upon a button click - assume the value of the first
displayed entry, allowing for continuous refresh with the same start address.
The will use the last entry of the currently displayed table as a basis for the next lookup. When
the end is reached the text "No more entries" is shown in the displayed table. Use the button
to start over.
Port :
Switch Port Number for which the entries are displayed.
VLAN ID :
VLAN-ID in which the ARP traffic is permitted.
MAC Address :
User MAC address of the entry.
IP Address :
User IP address of the entry.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
|<<: Updates the system log entries to the first available entry ID.
>> : Updates the system log entry to the next available entry ID.
3-6.2.5 IP Source Guard
Entries in the Dynamic IP Source Guard Table are shown on this page. The Dynamic IP
Source Guard Table is sorted first by port, then by VLAN ID, then by IP address, and
then by MAC address.
Web Interface
362
To configure a Dynamic IP Source Guard Table Configuration in the web interface:
1. Click Security, Network, IP Source Guard.
2. Checked “Auto-refresh”.
3. Click “Refresh” to refresh the port detailed statistics.
4. Specify the Start from port, VLAN ID, IP Address, and entries per page.
Figure 3-6.2.5: The Dynamic IP Source Table
Parameter description:
Port :
Switch Port Number for which the entries are displayed.
VLAN ID :
VLAN-ID in which the IP traffic is permitted.
IP Address :
User IP address of the entry.
MAC Address :
Source MAC address.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
363
occurs every 3 seconds.
Refresh: Click to refresh the page.
|<<: Updates the system log entries to the first available entry ID.
>> : Updates the system log entry to the next available entry ID.
364
3-6.3 AAA
3-6.3.1 RADIUS Overview
This section shows you an overview of the RADIUS Authentication and Accounting
servers’ status to ensure the function is workable.
Web Interface
To configure a RADIUS Overview Configuration in the web interface:
1. Click Security, AAA, RADIUS Overview.
2. Checked “Auto-refresh”.
3. Click “Refresh” to refresh the port detailed statistics.
Figure 3-6.3.1: The RADIUS Authentication Server Status Overview
Parameter description:
# :
The RADIUS server number. Click to navigate to detailed statistics for this server.
IP Address :
The IP address and UDP port number (in <IP Address>:<UDP Port> notation) of this
server.
365
State :
The current state of the server. This field takes one of the following values:
Disabled: The server is disabled.
Not Ready: The server is enabled, but IP communication is not yet up and running.
Ready: The server is enabled, IP communication is up and running, and the RADIUS
module is ready to accept access attempts.
Dead (X seconds left): Access attempts were made to this server, but it did not
reply within the configured timeout. The server has temporarily been disabled, but
will get re-enabled when the dead-time expires. The number of seconds left before
this occurs is displayed in parentheses. This state is only reachable when more than
one server is enabled.
RADIUS Accounting Servers
# :
The RADIUS server number. Click to navigate to detailed statistics for this server.
IP Address :
The IP address and UDP port number (in <IP Address>:<UDP Port> notation) of this
server.
State :
The current state of the server. This field takes one of the following values:
Disabled: The server is disabled.
Not Ready: The server is enabled, but IP communication is not yet up and running.
Ready: The server is enabled, IP communication is up and running, and the RADIUS
module is ready to accept accounting attempts.
Dead (X seconds left): Accounting attempts were made to this server, but it did
not reply within the configured timeout. The server has temporarily been disabled,
but will get re-enabled when the dead-time expires. The number of seconds left
366
before this occurs is displayed in parentheses. This state is only reachable when
more than one server is enabled.
367
3-6.3.2 RADIUS Details
This section shows you a detailed statistics for a particular RADIUS server.
Web Interface
To configure a RADIUS Details Configuration in the web interface:
1. Specify Port which want to check.
2. Click Security, AAA, RADIUS Overview.
3. Checked “Auto-refresh”.
4. Click “Refresh” to refresh the port detailed statistics or clear all information when you click
“Clear”. Fresh”.
Figure 3-6.3.2: The RADIUS Authentication Statistics Server
368
Parameter description:
RADIUS Authentication Statistics
The statistics map closely to those specified in RFC4668 - RADIUS Authentication Client MIB.
Use the server select box to switch between the backend servers to show details for.
Packet Counters
RADIUS authentication server packet counter. There are seven receive and four
transmit counters.
Direction
Name
RFC4668 Name
Description
Rx
Access
Accepts
radiusAuthClientExtAccessA
ccepts
The number of RADIUS Access-Accept
packets (valid or invalid) received from the
server.
Rx
Access
Rejects
radiusAuthClientExtAccessR
ejects
The number of RADIUS Access-Reject
packets (valid or invalid) received from the
server.
Rx
Access
Challenges
radiusAuthClientExtAccessC
hallenges
The number of RADIUS Access-Challenge
packets (valid or invalid) received from the
server.
Rx
Malformed
Access
Responses
radiusAuthClientExtMalform
edAccessResponses
The number of malformed RADIUS
Access-Response packets received from the
server. Malformed packets include packets
with an invalid length. Bad authenticators or
369
Message Authenticator attributes or
unknown types are not included as
malformed access responses.
Rx
Bad
Authenticato
rs
radiusAuthClientExtBadAuth
enticators
The number of RADIUS Access-Response
packets containing invalid authenticators or
Message Authenticator attributes received
from the server.
Rx
Unknown
Types
radiusAuthClientExtUnknow
nTypes
The number of RADIUS packets that were
received with unknown types from the
server on the authentication port and
dropped.
Rx
Packets
Dropped
radiusAuthClientExtPackets
Dropped
The number of RADIUS packets that were
received from the server on the
authentication port and dropped for some
other reason.
Tx
Access
Requests
radiusAuthClientExtAccessR
equests
The number of RADIUS Access-Request
packets sent to the server. This does not
include retransmissions.
Tx
Access
Retransmissi
ons
radiusAuthClientExtAccessR
etransmissions
The number of RADIUS Access-Request
packets retransmitted to the RADIUS
authentication server.
Tx
Pending
Requests
radiusAuthClientExtPending
Requests
The number of RADIUS Access-Request
packets destined for the server that have
not yet timed out or received a response.
This variable is incremented when an
Access-Request is sent and decremented
due to receipt of an Access-Accept,
Access-Reject, Access-Challenge, timeout,
or retransmission.
Tx
Timeouts
radiusAuthClientExtTimeout
s
The number of authentication timeouts to
the server. After a timeout, the client may
retry to the same server, send to a different
server, or give up. A retry to the same server
is counted as a retransmit as well as a
timeout. A send to a different server is
counted as a Request as well as a timeout.
Other Info
370
This section contains information about the state of the server and the latest
round-trip time.
Name
RFC4668 Name
Description
IP Address
-
IP address and UDP port for the authentication server in
question.
State
-
Shows the state of the server. It takes one of the following
values:
Disabled: The selected server is disabled.
Not Ready: The server is enabled, but IP communication is
not yet up and running.
Ready: The server is enabled, IP communication is up and
running, and the RADIUS module is ready to accept access
attempts.
Dead (X seconds left): Access attempts were made to this
server, but it did not reply within the configured timeout. The
server has temporarily been disabled, but will get re-enabled
when the dead-time expires. The number of seconds left
before this occurs is displayed in parentheses. This state is
only reachable when more than one server is enabled.
Round-Tri
p Time
radiusAuthClientExtRoundTr
ipTime
The time interval (measured in milliseconds) between the
most recent Access-Reply/Access-Challenge and the
Access-Request that matched it from the RADIUS
authentication server. The granularity of this measurement is
100 ms. A value of 0 ms indicates that there hasn't been
round-trip communication with the server yet.
RADIUS Accounting Statistics
The statistics map closely to those specified in RFC4670 - RADIUS Accounting Client MIB.
Use the server select box to switch between the backend servers to show details for.
Packet Counters
RADIUS accounting server packet counter. There are five receive and four transmit counters.
Direction
Name
RFC4670 Name
Description
Rx
Responses
radiusAccClientExtResponses
The number of RADIUS packets (valid
or invalid) received from the server.
371
Rx
Malformed
Responses
radiusAccClientExtMalformed
Responses
The number of malformed RADIUS
packets received from the server.
Malformed packets include packets
with an invalid length. Bad
authenticators or unknown types are
not included as malformed access
responses.
Rx
Bad
Authenticators
radiusAcctClientExtBadAuthen
ticators
The number of RADIUS packets
containing invalid authenticators
received from the server.
Rx
Unknown Types
radiusAccClientExtUnknownTy
pes
The number of RADIUS packets of
unknown types that were received
from the server on the accounting
port.
Rx
Packets
Dropped
radiusAccClientExtPacketsDro
pped
The number of RADIUS packets that
were received from the server on the
accounting port and dropped for
some other reason.
Tx
Requests
radiusAccClientExtRequests
The number of RADIUS packets sent
to the server. This does not include
retransmissions.
Tx
Retransmissions
radiusAccClientExtRetransmiss
ions
The number of RADIUS packets
retransmitted to the RADIUS
accounting server.
Tx
Pending
Requests
radiusAccClientExtPendingRe
quests
The number of RADIUS packets
destined for the server that have not
yet timed out or received a response.
This variable is incremented when a
Request is sent and decremented due
to receipt of a Response, timeout, or
retransmission.
Tx
Timeouts
radiusAccClientExtTimeouts
The number of accounting timeouts
to the server. After a timeout, the
client may retry to the same server,
send to a different server, or give up.
A retry to the same server is counted
as a retransmit as well as a timeout. A
372
send to a different server is counted
as a Request as well as a timeout.
Other Info
This section contains information about the state of the server and the latest
round-trip time.
Name
RFC4670 Name
Description
IP Address
-
IP address and UDP port for the accounting
server in question.
State
-
Shows the state of the server. It takes one of
the following values:
Disabled: The selected server is disabled.
Not Ready: The server is enabled, but IP
communication is not yet up and running.
Ready: The server is enabled, IP
communication is up and running, and the
RADIUS module is ready to accept accounting
attempts.
Dead (X seconds left): Accounting attempts
were made to this server, but it did not reply
within the configured timeout. The server has
temporarily been disabled, but will get
re-enabled when the dead-time expires. The
number of seconds left before this occurs is
displayed in parentheses. This state is only
reachable when more than one server is
enabled.
Round-Trip
Time
radiusAccClientExtRoundTripTime
The time interval (measured in milliseconds)
between the most recent Response and the
Request that matched it from the RADIUS
accounting server. The granularity of this
measurement is 100 ms. A value of 0 ms
indicates that there hasn't been round-trip
communication with the server yet.
Buttons:
373
Auto-refresh –Check this box to enable an automatic refresh of the page at regular
intervals.
Refresh - Click to refresh the page immediately.
Clear - Clears the counters for the selected server. The "Pending Requests" counter
will not be cleared by this operation.
374
3-6.4 Switch
3-6.4.1 RMON
3-6.4.1.1 Statistics
This section provides an overview of RMON Statistics entries. Each page shows up to
99 entries from the Statistics table, default being 20, selected through the "entries per
page" input field. When first visited, the web page will show the first 20 entries from
the beginning of the Statistics table. The first displayed will be the one with the lowest
ID found in the Statistics table.
The "Start from Control Index" allows the user to select the starting point in the
Statistics table. Clicking the button will update the displayed table starting from that or
the next closest Statistics table match.
The will use the last entry of the currently displayed entry as a basis for the next
lookup. When the end is reached the text "No more entries" is shown in the displayed
table. Use the button to start over.
Web Interface
To configure a RMON Statistics in the web interface:
1. Specify Port which want to check.
2. Click Security, Switch, RMON, Statistics.
3. Checked “Auto-refresh”.
4. Click “Refresh” to refresh the port detailed statistics.
Figure 3-6.4.1.1: The RMON Statistics Status Overview
375
Parameter description:
ID
Indicates the index of Statistics entry.
Data Source(if Index)
The port ID which wants to be monitored.
Drop
The total number of events in which packets were dropped by the probe due to lack
of resources.
Octets
The total number of octets of data (including those in bad packets) received on the
network.
Pkts
The total number of packets (including bad packets, broadcast packets, and
multicast packets) received.
Broad-cast
The total number of good packets received that were directed to the broadcast
address.
Multi-cast
The total number of good packets received that were directed to a multicast
address.
CRC Errors
The total number of packets received that had a length (excluding framing bits, but
including FCS octets) of between 64 and 1518 octets, inclusive, but had either a bad
Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad
FCS with a non-integral number of octets (Alignment Error).
Under-size
The total number of packets received that were less than 64 octets.
376
Over-size
The total number of packets received that were longer than 1518 octets.
Frag.
The number of frames which size is less than 64 octets received with invalid CRC.
Jabb.
The number of frames which size is larger than 64 octets received with invalid CRC.
Coll.
The best estimate of the total number of collisions on this Ethernet segment.
64
The total number of packets (including bad packets) received that were 64 octets in
length.
65~127
The total number of packets (including bad packets) received that were between 65
to 127 octets in length.
128~255
The total number of packets (including bad packets) received that were between 128
to 255 octets in length.
256~511
The total number of packets (including bad packets) received that were between
256 to 511 octets in length.
512~1023
The total number of packets (including bad packets) received that were between
512 to 1023 octets in length.
1024~1588
The total number of packets (including bad packets) received that were between
1024 to 1588 octets in length.
Buttons
377
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page immediately.
|<< : Updates the table starting from the first entry in the Statistics table, i.e. the
entry with the lowest ID.
>> : Updates the table, starting with the entry after the last entry currently
displayed.
378
3-6.4.1.2 History
This section provides an overview of RMON History entries. Each page shows up to 99
entries from the History table, default being 20, selected through the "entries per
page" input field. When first visited, the web page will show the first 20 entries from
the beginning of the History table. The first displayed will be the one with the lowest
History Index and Sample Index found in the History table.
The "Start from History Index and Sample Index" allows the user to select the starting
point in the History table.
The "Start from History Index and Sample Index" allows the user to select the starting
point in the History table. Clicking the button will update the displayed table starting
from that or the next closest History table match.
The will use the last entry of the currently displayed entry as a basis for the next
lookup. When the end is reached the text "No more entries" is shown in the displayed
table. Use the button to start over.
Web Interface
To configure a RMON history Configuration in the web interface:
1. Specify Port which wants to check.
2. Click Security, Switch, RMON, History.
3. Checked “Auto-refresh”.
4. Click “Refresh” to refresh the port detailed statistics or clear all information when
you click “ Clear”.
Figure 3-6.4.1.2: RMON History Overview
379
Parameter description:
History Index
Indicates the index of History control entry.
Sample Index
Indicates the index of the data entry associated with the control entry.
Sample Start
The value of sysUpTime at the start of the interval over which this sample was
measured.
Drop
The total number of events in which packets were dropped by the probe due to lack
of resources.
Octets
The total number of octets of data (including those in bad packets) received on the
network.
Pkts
The total number of packets (including bad packets, broadcast packets, and
multicast packets) received.
Broadcast
The total number of good packets received that were directed to the broadcast
address.
Multicast
The total number of good packets received that were directed to a multicast
address.
CRCErrors
The total number of packets received that had a length (excluding framing bits, but
including FCS octets) of between 64 and 1518 octets, inclusive, but had either a bad
Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad
FCS with a non-integral number of octets (Alignment Error).
Undersize
380
The total number of packets received that were less than 64 octets.
Oversize
The total number of packets received that were longer than 1518 octets.
Frag.
The number of frames which size is less than 64 octets received with invalid CRC.
Jabb.
The number of frames which size is larger than 64 octets received with invalid CRC.
Coll.
The best estimate of the total number of collisions on this Ethernet segment.
Utilization
The best estimate of the mean physical layer network utilization on this interface
during this sampling interval, in hundredths of a percent.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page immediately.
|<< : Updates the table starting from the first entry in the History table, i.e., the
entry with the lowest History Index and Sample Index
>> : Updates the table, starting with the entry after the last entry currently
displayed
381
3-6.4.1.3 Alarm
This page provides an overview of RMON Alarm entries. Each page shows up to 99
entries from the Alarm table, default being 20, selected through the "entries per page"
input field. When first visited, the web page will show the first 20 entries from the
beginning of the Alarm table. The first displayed will be the one with the lowest ID
found in the Alarm table.
The "Start from Control Index" allows the user to select the starting point in the Alarm
table.
Clicking the button will update the displayed table starting from that or the next
closest Alarm table match.
The will use the last entry of the currently displayed entry as a basis for the next
lookup. When the end is reached the text "No more entries" is shown in the displayed
table. Use the button to start over.
Web Interface
To configure a RMON Alarm Overview in the web interface:
1. Specify Port which wants to check.
2. Click Security, Switch, RMON, Alarm.
3. Checked “Auto-refresh”.
4. Click “Refresh” to refresh the port detailed statistics.
Figure 3-6.4.1.3: RMON Alarm Overview
382
Parameter description:
ID
Indicates the index of Alarm control entry.
Interval
Indicates the interval in seconds for sampling and comparing the rising and falling
threshold.
Variable
Indicates the particular variable to be sampled
Sample Type
The method of sampling the selected variable and calculating the value to be
compared against the thresholds.
Value
The value of the statistic during the last sampling period.
Startup Alarm
The alarm that may be sent when this entry is first set to valid.
Rising Threshold
Rising threshold value.
Rising Index
Rising event index.
Falling Threshold
Falling threshold value.
Falling Index
Falling event index.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh occurs
383
every 3 seconds.
Refresh: Click to refresh the page immediately.
|<<: Updates the table starting from the first entry in the Alarm Table, i.e. the entry with the
lowest ID.
>> : Updates the table, starting with the entry after the last entry currently displayed.
384
3-6.4.1.4 Event
This page provides an overview of RMON Event table entries. Each page shows up to
99 entries from the Event table, default being 20, selected through the "entries per
page" input field. When first visited, the web page will show the first 20 entries from
the beginning of the Event table. The first displayed will be the one with the lowest
Event Index and Log Index found in the Event table .
The "Start from Event Index and Log Index" allows the user to select the starting point
in the Event table. Clicking the button will update the displayed table starting from
that or the next closest Event table match.
The will use the last entry of the currently displayed entry as a basis for the next
lookup. When the end is reached the text "No more entries" is shown in the displayed
table. Use the button to start over.
Web Interface
To configure a RMON Event Overview in the web interface:
1. Click Security, Switch, RMON, Event.
2. Checked “Auto-refresh”.
3. Click “ Refresh“ to refresh the port detailed statistics
4. Specify Port which wants to check.
Figure 3-6.4.1.4: RMON Event Overview
Parameter description:
Event Index
385
Indicates the index of the event entry.
Log Index
Indicates the index of the log entry.
LogTIme
Indicates Event log time
LogDescription
Indicates the Event description.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page immediately.
|<< : Updates the table starting from the first entry in the Event Table, i.e. the entry
with the lowest Event Index and Log Index.
>>: Updates the table, starting with the entry after the last entry currently
displayed
386
3-7 Aggregation
3-7.1 Status
This page is used to see the status of ports in Aggregation group
Web Interface
To display the status of ports in the web interface:
1. Click Monitor, Aggregation, Status
2. Checked “Auto-refresh”.
3. Click “Refresh” to refresh the port detailed statistics.
Figure 3-7.1 The LACP System Status
Parameter description:
Aggr ID :
The Aggregation ID associated with this aggregation instance.
Name
Name of the Aggregation group ID.
Type
Type of the Aggregation group(Static or LACP).
Speed
Speed of the Aggregation group.
387
Configured ports
Configured member ports of the Aggregation group.
Aggregated ports
Aggregated member ports of the Aggregation group
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
3-7.2 LACP
3-7.2.1.1 System Status
This page provides a status overview for all LACP instances
Web Interface
To display the System Status in the web interface:
1. Click Monitor, LACP, System Status
2. If you want to auto-refresh the information then you need to evoke the “Auto
refresh”.
3. 3. Click “Refresh” to refresh the LACP Statistics.
Figure 3-7.2.1.1: The System Status
388
Parameter description:
Aggr ID
The Aggregation ID associated with this aggregation instance. For LLAG the id is
shown as 'isid:aggr-id' and for GLAGs as 'aggr-id'
Partner System ID
The system ID (MAC address) of the aggregation partner.
Partner Key
The Key that the partner has assigned to this aggregation ID.
Partner Prio
The priority of this partner.
Last Changed
The time since this aggregation changed.
Local Ports
Shows which ports are a part of this aggregation for this switch.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
3-7.2.1.2 Port Status
This page provides a status overview for LACP status for all ports.
Web Interface
To display the Port Status in the web interface:
1. Click Monitor, LACP, Port Status
2. If you want to auto-refresh the information then you need to evoke the
“Auto refresh”.
3. Click “Refresh” to refresh the LACP Status.
389
Figure 3-7.2.1.1: The System Status
Parameter description:
Port
The switch port number.
LACP
'Yes' means that LACP is enabled and the port link is up. 'No' means that LACP is not
enabled or that the port link is down. 'Backup' means that the port could not join
the aggregation group but will join if other port leaves. Meanwhile it's LACP status
is disabled.
Key
The key assigned to this port. Only ports with the same key can aggregate together.
Aggr ID
The Aggregation ID assigned to this aggregation group.
Partner System ID
The partner's System ID (MAC address).
Partner Port
The partner's port number connected to this port.
Partner Prio
The partner's port priority.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
3-7.2.1.3 Port Statistics
390
This page provides an overview for LACP statistics for all ports.
Web Interface
To display the LACP Port Statistics in the web interface:
4. Click Monitor, LACP, Port Statistics
5. If you want to auto-refresh the information then you need to evoke the “Auto
refresh”.
6. 3. Click “Refresh” to refresh the LACP Statistics.
Figure 3-7.2.1.3: The Port Statistics
Parameter description:
Port
The switch port number.
LACP Received
Shows how many LACP frames have been received at each port.
LACP Transmitted
Shows how many LACP frames have been sent from each port.
Discarded
Shows how many unknown or illegal LACP frames have been discarded at each
port.
Buttons
391
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Clear: Clears the counters for the selected port.
Refresh: Click to refresh the page.
392
3-8 Loop Protection
This section displays the loop protection port status the ports of the currently selected
switch.
Web Interface
To display the Loop Protection status in the web interface:
1. Click Monitor, Loop Protection
2. If you want to auto-refresh the information then you need to evoke the “Auto
refresh”.
3. Click “Refresh” to refresh the LACP Statistics.
Figure 3-8 : Loop Protection Status
Parameter description:
Port
The switch port number of the logical port.
Action
The currently configured port action.
Transmit
The currently configured port transmit mode.
Loops
The number of loops detected on this port.
393
Status
The current loop protection status of the port.
Loop
Whether a loop is currently detected on the port.
Time of Last Loop
The time of the last loop event detected.
Buttons
Refresh: Click to refresh the page immediately.
Auto-refresh: Check this box to enable an automatic refresh of the page at regular
intervals.
394
3-9 Spanning Tree
3-9.1 Bridge Status
After you complete the MSTI Port configuration then you could to ask the switch
display the Bridge Status. The Section provides a status overview of all STP bridge
instances. The displayed table contains a row for each STP bridge instance, where the
column displays the following information:
Web Interface
To display the STP Bridges status in the web interface:
1. Click Monitor, Spanning Tree, STP Bridges
2. If you want to auto-refresh the information then you need to evoke the
“Auto-refresh”.
3. Click “Refresh” to refresh the STP Bridges.
4. Click “CIST “to next page “STP Detailed Bridge Status”.
Figure 3-9.1: The STP Bridges status
Parameter description:
MSTI :
The Bridge Instance. This is also a link to the STP Detailed Bridge Status.
Bridge ID :
The Bridge ID of this Bridge instance.
Root ID :
395
The Bridge ID of the currently elected root bridge.
Root Port :
The switch port currently assigned the root port role.
Root Cost :
Root Path Cost. For the Root Bridge it is zero. For all other Bridges, it is the sum of
the Port Path Costs on the least cost path to the Root Bridge.
Topology Flag :
The current state of the Topology Change Flag of this Bridge instance.
Topology Change Last :
The time since last Topology Change occurred.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
396
3-9.2 Port Status
After you complete the STP configuration then you could to ask the switch display the
STP Port Status. The Section provides you to ask switch to display the STP CIST port
status for physical ports of the currently selected switch.
Web Interface
To display the STP Port status in the web interface:
1. Click Monitor, Spanning Tree, STP Port Status
2. If you want to auto-refresh the information then you need to evoke the
“Auto-refresh”.
3. Click “Refresh” to refresh the STP Bridges.
Figure 3-9.2: The STP Port status
Parameter description:
Port :
The switch port number of the logical STP port.
CIST Role :
The current STP port role of the CIST port. The port role can be one of the following
values: AlternatePort, Backup Port, RootPort, DesignatedPort Disabled.
397
CIST State :
The current STP port state of the CIST port. The port state can be one of the
following values: Blocking Learning Forwarding.
Uptime
The time since the bridge port was last initialized.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
398
3-9.3 Port Statistics
After you complete the STP configuration then you could to let the switch display the
STP Statistics. The Section provides you to ask switch to display the STP Statistics detail
counters of bridge ports in the currently selected switch.
Web Interface
To display the STP Port status in the web interface:
1. Click Monitor, Spanning Tree, Port Statistics
2. If you want to auto-refresh the information then you need to evoke the
“Auto-refresh”.
3. Click “Refresh” to refresh the STP Bridges.
Figure 3-9.3: The STP Statistics
Parameter description:
Port :
The switch port number of the logical STP port.
MSTP :
The number of MSTP Configuration BPDU's received/transmitted on the port.
RSTP :
The number of RSTP Configuration BPDU's received/transmitted on the port.
STP :
The number of legacy STP Configuration BPDU's received/transmitted on the port.
399
TCN :
The number of (legacy) Topology Change Notification BPDU's received/transmitted
on the port.
Discarded Unknown :
The number of unknown Spanning Tree BPDU's received (and discarded) on the
port.
Discarded Illegal :
The number of illegal Spanning Tree BPDU's received (and discarded) on the port.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Clear: Clears the counters for the selected port.
Refresh: Click to refresh the page.
400
3-10 MVR
3-10.1 Statistics
The section describes the switch will display the MVR detail Statistics after you had
configured MVR on the switch. It provides the detail MVR Statistics Information
Web Interface
To display the MVR Statistics Information in the web interface:
1. Click Monitor, MVR, Statistics
2. If you want to auto-refresh the information then you need to evoke the
“Auto-refresh”.
3. To click the “Refresh” to refresh an entry of the MVR Statistics Information.
Figure 3-10.1: The MVR Statistics Information
Parameter description:
VLAN ID
The Multicast VLAN ID.
IGMP/MLD Queries Received
The number of Received Queries for IGMP and MLD, respectively.
IGMP/MLD Queries Transmitted
The number of Transmitted Queries for IGMP and MLD, respectively.
IGMPv1 Joins Received
The number of Received IGMPv1 Join's.
401
IGMPv2/MLDv1 Report's Received
The number of Received IGMPv2 Join's and MLDv1 Report's, respectively.
IGMPv3/MLDv2 Report's Received
The number of Received IGMPv1 Join's and MLDv2 Report's, respectively.
IGMPv2/MLDv1 Leave's Received
The number of Received IGMPv2 Leave's and MLDv1 Done's, respectively.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Clear: Clears the counters for the selected port.
Refresh: Click to refresh the page.
402
3-10.2 MVR Channels Groups
The section describes user could display the MVR Groups detail information on the
switch. Entries in the MVR Group Table are shown on this page. The MVR Group Table
is sorted first by VLAN ID, and then by group
Web Interface
To display the MVR Groups Information in the web interface:
1. Click Monitor, MVR, Groups Information
2. If you want to auto-refresh the information then you need to evoke the
“Auto-refresh”.
3. To click the “Refresh” to refresh an entry of the MVR Groups Information.
4. Click “<< or >> “to move to previous or next entry.
Figure 3-10.2: The MVR Groups Information
Parameter description:
Navigating the MVR Channels (Groups) Information Table
Each page shows up to 99 entries from the MVR Group table, default being 20,
selected through the "entries per page" input field. When first visited, the web page
will show the first 20 entries from the beginning of the MVR Channels (Groups)
Information Table.
403
The "Start from VLAN", and "Group Address" input fields allow the user to select the
starting point in the MVR Channels (Groups) Information Table. Clicking the button will
update the displayed table starting from that or the closest next MVR Channels
(Groups) Information Table match. In addition, the two input fields will - upon a button
click - assume the value of the first displayed entry, allowing for continuous refresh
with the same start address.
The will use the last entry of the currently displayed table as a basis for the next lookup.
When the end is reached the text "No more entries" is shown in the displayed table.
Use the button to start over
MVR Channels (Groups) Information Table Columns
VLAN ID :
VLAN ID of the group.
Groups :
Group ID of the group displayed.
Port Members :
Ports under this group.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
|<<: Updates the system log entries to the first available entry ID
>> : Updates the system log entry to the next available entry ID
404
3-10.3 MVR SFM Information
The MVR SFM (Source-Filtered Multicast) Information Table also contains the SSM
(Source-Specific Multicast) information. This table is sorted first by VLAN ID, then by
group, and then by Port. Different source addresses belong to the same group are
treated as single entry.
Web Interface
To display the MVR SFM Information in the web interface:
1. Click Monitor, MVR, MVR SFM Information
2. If you want to auto-refresh the information then you need to evoke the
“Auto-refresh”.
3. To click the “Refresh” to refresh an entry of the MVR Groups Information.
4. Click “<< or >> “to move to previous or next entry.
Figure 3-10.3: The MVR SFM Information
Parameter description:
Navigating the MVR SFM Information Table
Each page shows up to 99 entries from the MVR SFM Information Table, default being
20, selected through the "entries per page" input field. When first visited, the web page
will show the first 20 entries from the beginning of the MVR SFM Information Table.
The "Start from VLAN", and "Group Address" input fields allow the user to select the
starting point in the MVR SFM Information Table. Clicking the button will update the
405
displayed table starting from that or the closest next MVR SFM Information Table
match. In addition, the two input fields will - upon a button click - assume the value of
the first displayed entry, allowing for continuous refresh with the same start address.
The will use the last entry of the currently displayed table as a basis for the next lookup.
When the end is reached the text "No more entries" is shown in the displayed table.
Use the button to start over.
MVR SFM Information Table Columns
VLAN ID
VLAN ID of the group.
Group
Group address of the group displayed.
Port
Switch port number.
Mode
Indicates the filtering mode maintained per (VLAN ID, port number, Group Address)
basis. It can be either Include or Exclude.
Source Address
IP Address of the source. Currently, system limits the total number of IP source
addresses for filtering to be 128. When there is no any source filtering address, the
text "None" is shown in the Source Address field.
Type
Indicates the Type. It can be either Allow or Deny.
Hardware Filter/Switch
Indicates whether data plane destined to the specific group address from the
source IPv4/IPv6 address could be handled by chip or not.
Buttons
406
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
|<<: Updates the system log entries to the first available entry ID
>> : Updates the system log entry to the next available entry ID
407
3-11 IPMC
3-11.1 IGMP Snooping
3-11.1.1 Status
After you complete the IGMP Snooping configuration, then you could to let the switch
display the IGMP Snooping Status. The Section provides you to let switch to display
the IGMP Snooping detail status.
Web Interface
To display the IGMP Snooping status in the web interface:
1. Click Monitor, IGMP Snooping, Status
2. If you want to auto-refresh the information then you need to evoke the
“Auto-refresh”.
3. Click “Refresh” to refresh the IGMP Snooping Status.
4. Click “Clear “to clear the IGMP Snooping Status.
Figure 3-11.1.1: The IGMP Snooping Status.
408
Parameter description:
VLAN ID :
The VLAN ID of the entry.
Querier Version :
Working Querier Version currently.
Host Version :
Working Host Version currently.
Querier Status :
Shows the Querier status is "ACTIVE" or "IDLE".
"DISABLE" denotes the specific interface is administratively disabled.
Queries Transmitted :
The number of Transmitted Queries.
Queries Received :
The number of Received Queries.
V1 Reports Received :
The number of Received V1 Reports.
V2 Reports Received :
The number of Received V2 Reports.
V3 Reports Received :
The number of Received V3 Reports.
V2 Leaves Received :
The number of Received V2 Leaves.
409
Router Port
Display which ports act as router ports. A router port is a port on the Ethernet
switch that leads towards the Layer 3 multicast device or IGMP querier.
Static denotes the specific port is configured to be a router port.
Dynamic denotes the specific port is learnt to be a router port.
Both denote the specific port is configured or learnt to be a router port.
Port
Switch port number.
Status
Indicate whether specific port is a router port or not.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Clear: Clears the counters for the selected port.
Refresh: Click to refresh the page.
410
3-11.1.2 Group Information
After you complete to set the IGMP Snooping function then you could let the switch to
display the IGMP Snooping Group Information. Entries in the IGMP Group Table are
shown on this page. The IGMP Group Table is sorted first by VLAN ID, and then by
group. The will use the last entry of the currently displayed table as a basis for the next
lookup. When the end is reached the text "No more entries" is shown in the displayed
table. Use the button to start over.
Web Interface
To display the IGMP Snooping Group Information in the web interface:
1. Click Monitor, IGMP Snooping, Group Information
2. If you want to auto-refresh the information then you need to evoke the
“Auto-refresh”.
3. Click “Refresh” to refresh an entry of the IGMP Snooping Groups Information.
4. Click “<< or >> “to move to previous or next entry.
Figure 3-11.1.2: The IGMP Snooping Groups Information.
Parameter description:
Navigating the IGMP Group Table
Each page shows up to 99 entries from the IGMP Group table, default being 20,
selected through the "entries per page" input field. When first visited, the web page
will show the first 20 entries from the beginning of the IGMP Group Table.
411
The "Start from VLAN", and "group" input fields allow the user to select the starting
point in the IGMP Group Table. Clicking the button will update the displayed table
starting from that or the closest next IGMP Group Table match. In addition, the two
input fields will - upon a button click - assume the value of the first displayed entry,
allowing for continuous refresh with the same start address.
The will use the last entry of the currently displayed table as a basis for the next lookup.
When the end is reached the text "No more entries" is shown in the displayed table.
Use the button to start over.
IGMP Group Table Columns
VLAN ID :
VLAN ID of the group.
Groups :
Group address of the group displayed.
Port Members :
Ports under this group.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
|<<: Updates the system log entries to the first available entry ID
>> : Updates the system log entry to the next available entry ID
412
3-11.1.3 IPv4 SFM Information
Entries in the IGMP SFM Information Table are shown on this page. The IGMP SFM
(Source-Filtered Multicast) Information Table also contains the SSM (Source-Specific
Multicast) information. This table is sorted first by VLAN ID, then by group, and then
by Port. Different source addresses belong to the same group are treated as single
entry.
Web Interface
To display the IPv4 SSM Information in the web interface:
1. Click Monitor, IGMP Snooping, IPv4 SSM Information
2. If you want to auto-refresh the information then you need to evoke the
“Auto-refresh”.
3. Click “Refresh” to refresh an entry of the IPv4 SFM Information.
4. Click “<< or >> “to move to previous or next entry.
Figure 3-11.1.3: The IPv4 SFM Information.
Parameter description:
Navigating the IGMP SFM Information Table
Each page shows up to 99 entries from the IGMP SFM Information table, default being
20, selected through the "entries per page" input field. When first visited, the web
page will show the first 20 entries from the beginning of the IGMP SFM Information
Table.
413
The "Start from VLAN", and "group" input fields allow the user to select the starting
point in the IGMP SFM Information Table. Clicking the button will update the
displayed table starting from that or the closest next IGMP SFM Information Table
match. In addition, the two input fields will - upon a button click - assume the value of
the first displayed entry, allowing for continuous refresh with the same start address.
The will use the last entry of the currently displayed table as a basis for the next lookup.
When the end is reached the text "No more entries" is shown in the displayed table.
Use the button to start over.
IGMP SFM Information Table Columns
VLAN ID :
VLAN ID of the group.
Group :
Group address of the group displayed.
Port :
Switch port number.
Mode :
Indicates the filtering mode maintained per (VLAN ID, port number, Group Address)
basis. It can be either Include or Exclude.
Source Address :
IP Address of the source. Currently, system limits the total number of IP source
addresses for filtering to be 128.
Type :
Indicates the Type. It can be either Allow or Deny.
Hardware Filter/Switch
Indicates whether data plane destined to the specific group address from the
source IPv4 address could be handled by chip or not.
Buttons
414
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
|<<: Updates the system log entries to the first available entry ID
>>: Updates the system log entry to the next available entry ID
415
3-11.2 MLD Snooping
3-11.2.1 Status
The section describes when you complete the MLD Snooping and how to display the
MLD Snooping Status and detail information. It will help you to find out the detail
information of MLD Snooping status.
Web Interface
To display the MLD Snooping Status in the web interface:
1. Click Monitor, MLD Snooping, Status
2. If you want to auto-refresh the information then you need to evoke the
“Auto-refresh”
3. Click “Refresh” to refresh an entry of the MLD Snooping Status Information.
4. Click “Clear “to clear the MLD Snooping Status.
Figure 3-11.2.1: The MLD Snooping Status
416
Parameter description:
VLAN ID :
The VLAN ID of the entry.
Querier Version :
Working Querier Version currently.
Host Version :
Working Host Version currently.
Querier Status :
Show the Querier status is "ACTIVE" or "IDLE".
"DISABLE" denotes the specific interface is administratively disabled.
Queries Transmitted :
The number of Transmitted Queries.
Queries Received :
The number of Received Queries.
V1 Reports Received :
The number of Received V1 Reports.
V2 Reports Received :
The number of Received V2 Reports.
V1 Leaves Received :
The number of Received V1 Leaves.
Router Port
Display which ports act as router ports. A router port is a port on the Ethernet
switch that leads towards the Layer 3 multicast device or MLD querier.
Static denotes the specific port is configured to be a router port.
Dynamic denotes the specific port is learnt to be a router port.
Both denote the specific port is configured or learnt to be a router port.
Port
417
Switch port number.
Status
Indicate whether specific port is a router port or not.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Clear: Clears the counters for the selected port.
Refresh: Click to refresh the page.
418
3-11.2.2 Group Information
The section describes user could set the MLD Snooping Groups Information. The "Start
from VLAN", and "group" input fields allow the user to select the starting point in the
MLD Group Table
Web Interface
To display the MLD Snooping Group information in the web interface:
1. Click Monitor, MLD Snooping, Group Information
2. If you want to auto-refresh the information then you need to evoke the
“Auto-refresh”
3. Click “Refresh” to refresh an entry of the MLD Snooping Group Information.
4. Click “Clear “to clear the MLD Snooping Groups information..
Figure 3-11.2.2: The MLD Snooping Groups Information
Parameter description:
Navigating the MLD Group Table
Each page shows up to 99 entries from the MLD Group table, default being 20,
selected through the "entries per page" input field. When first visited, the web page
will show the first 20 entries from the beginning of the MLD Group Table.
The "Start from VLAN", and "group" input fields allow the user to select the starting
point in the MLD Group Table. Clicking the button will update the displayed table
starting from that or the closest next MLD Group Table match. In addition, the two
419
input fields will - upon a button click - assume the value of the first displayed entry,
allowing for continuous refresh with the same start address.
The will use the last entry of the currently displayed table as a basis for the next lookup.
When the end is reached the text "No more entries" is shown in the displayed table.
Use the button to start over.
MLD Snooping Information Table Columns
VLAN ID :
VLAN ID of the group.
Groups :
Group address of the group displayed.
Port Members :
Ports under this group.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
|<<: Updates the system log entries to the first available entry ID
>> : Updates the system log entry to the next available entry ID
420
3-11.2.3 IPv6 SFM Information
Entries in the MLD SFM Information Table are shown on this page. The MLD SFM
(Source-Filtered Multicast) Information Table also contains the SSM (Source-Specific
Multicast) information. This table is sorted first by VLAN ID, then by group, and then
by Port. Different source addresses belong to the same group are treated as single
entry.
Web Interface
To display the MLDv2 IPv6 SSM Information in the web interface:
1. Click Monitor, MLD Snooping, IPv6 SFM Information.
2. If you want to auto-refresh the information then you need to evoke the
“Auto-refresh”.
3. Click “Refresh” to refresh an entry of the MLDv2 IPv6 SSM Information.
4. Click “<< or >> “to move to previous or next entry.
Figure 3-11.2.3: The IPv6 SFM Information
Parameter description:
Navigating the MLD SFM Information Table
Each page shows up to 99 entries from the MLD SFM Information table, default being
20, selected through the "entries per page" input field. When first visited, the web
page will show the first 20 entries from the beginning of the MLD SFM Information
Table.
The "Start from VLAN", and "group" input fields allow the user to select the starting
421
point in the MLD SFM Information Table. Clicking the button will update the displayed
table starting from that or the closest next MLD SFM Information Table match. In
addition, the two input fields will - upon a button click - assume the value of the first
displayed entry, allowing for continuous refresh with the same start address.
The will use the last entry of the currently displayed table as a basis for the next lookup.
When the end is reached the text "No more entries" is shown in the displayed table.
Use the button to start over.
MLD SFM Information Table Columns
VLAN ID :
VLAN ID of the group.
Group :
Group address of the group displayed.
Port :
Switch port number.
Mode :
Indicates the filtering mode maintained per (VLAN ID, port number, Group Address)
basis. It can be either Include or Exclude.
Source Address :
IP Address of the source. Currently, system limits the total number of IP source
addresses for filtering to be 128.
Type :
Indicates the Type. It can be either Allow or Deny.
Hardware Filter/Switch
Indicates whether data plane destined to the specific group address from the
source IPv6 address could be handled by chip or not.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
422
occurs every 3 seconds.
Refresh: Click to refresh the page.
|<<: Updates the system log entries to the first available entry ID
>> : Updates the system log entry to the next available entry ID
423
3-12 LLDP
3-12.1 Neighbour
This page provides a status overview for all LLDP neighbours. The displayed table
contains a row for each port on which an LLDP neighbour is detected. The columns
hold the following information:
Web Interface
To show LLDP neighbours:
1. Click Monitor, LLDP, Neighbours.
2. Click Refresh for manual update web screen
3. Click Auto-refresh for auto-update web screen
Figure 3-12.1: The LLDP Neighbours information
NOTE: If your network without any device supports LLDP then
the table will show “No LLDP neighbour information found”.
Parameter description:
Local Port :
The port on which the LLDP frame was received.
Chassis ID :
The Chassis ID is the identification of the neighbour's LLDP frames.
Port ID :
424
The Remote Port ID is the identification of the neighbour port.
Port Description :
Port Description is the port description advertised by the neighbour unit.
System Name :
System Name is the name advertised by the neighbour unit.
System Capabilities :
System Capabilities describes the neighbour unit's capabilities. The possible
capabilities are:
1. Other
2. Repeater
3. Bridge
4. WLAN Access Point
5. Router
6. Telephone
7. DOCSIS cable device
8. Station only
9. Reserved
When a capability is enabled, the capability is followed by (+). If the capability is
disabled, the capability is followed by (-).
Management Address :
Management Address is the neighbour unit's address that is used for higher layer
entities to assist discovery by the network management. This could for instance
hold the neighbour's IP address.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
425
Refresh: Click to refresh the page.
426
3-12.2 LLDP-MED Neighbour
This page provides a status overview of all LLDP-MED neighbours. The displayed table
contains a row for each port on which an LLDP neighbour is detected. This function
applies to VoIP devices which support LLDP-MED. The columns hold the following
information:
Web Interface
To show LLDP-MED neighbor:
1. Click Monitor, LLDP, LLDP-MED Neighbor.
2. Click Refresh for manual update web screen
3. Click Auto-refresh for auto-update web screen
Figure 3-12.2: The LLDP-MED Neighbours information
NOTE: If your network without any device supports LLDP-MED
then the table will show “No LLDP-MED neighbour information
found”.
Parameter description:
Port :
The port on which the LLDP frame was received.
Device Type :
LLDP-MED Devices are comprised of two primary Device Types: Network
Connectivity Devices and Endpoint Devices.
LLDP-MED Network Connectivity Device Definition
LLDP-MED Network Connectivity Devices, as defined in TIA-1057, provide access to
427
the IEEE 802 based LAN infrastructure for LLDP-MED Endpoint Devices. An
LLDP-MED Network Connectivity Device is a LAN access device based on any of the
following technologies:
1. LAN Switch/Router
2. IEEE 802.1 Bridge
3. IEEE 802.3 Repeater (included for historical reasons)
4. IEEE 802.11 Wireless Access Point
5. Any device that supports the IEEE 802.1AB and MED extensions defined by
TIA-1057 and can relay IEEE 802 frames via any method.
LLDP-MED Endpoint Device Definition :
LLDP-MED Endpoint Devices, as defined in TIA-1057, are located at the IEEE 802
LAN network edge, and participate in IP communication service using the
LLDP-MED framework.
Within the LLDP-MED Endpoint Device category, the LLDP-MED scheme is broken
into further Endpoint Device Classes, as defined in the following.
Each LLDP-MED Endpoint Device Class is defined to build upon the capabilities
defined for the previous Endpoint Device Class. For-example will any LLDP-MED
Endpoint Device claiming compliance as a Media Endpoint (Class II) also support all
aspects of TIA-1057 applicable to Generic Endpoints (Class I), and any LLDP-MED
Endpoint Device claiming compliance as a Communication Device (Class III) will also
support all aspects of TIA-1057 applicable to both Media Endpoints (Class II) and
Generic Endpoints (Class I).
LLDP-MED Generic Endpoint (Class I) :
The LLDP-MED Generic Endpoint (Class I) definition is applicable to all endpoint
products that require the base LLDP discovery services defined in TIA-1057,
however do not support IP media or act as an end-user communication appliance.
Such devices may include (but are not limited to) IP Communication Controllers,
other communication related servers, or any device requiring basic services as
defined in TIA-1057.
Discovery services defined in this class include LAN configuration, device location,
network policy, power management, and inventory management.
LLDP-MED Media Endpoint (Class II) :
428
The LLDP-MED Media Endpoint (Class II) definition is applicable to all endpoint
products that have IP media capabilities however may or may not be associated
with a particular end user. Capabilities include all of the capabilities defined for the
previous Generic Endpoint Class (Class I), and are extended to include aspects
related to media streaming. Example product categories expected to adhere to this
class include (but are not limited to) Voice / Media Gateways, Conference Bridges,
Media Servers, and similar.
Discovery services defined in this class include media-type-specific network layer
policy discovery.
LLDP-MED Communication Endpoint (Class III) :
The LLDP-MED Communication Endpoint (Class III) definition is applicable to all
endpoint products that act as end user communication appliances supporting IP
media. Capabilities include all of the capabilities defined for the previous Generic
Endpoint (Class I) and Media Endpoint (Class II) classes, and are extended to include
aspects related to end user devices. Example product categories expected to adhere
to this class include (but are not limited to) end user communication appliances,
such as IP Phones, PC-based softphones, or other communication appliances that
directly support the end user.
Discovery services defined in this class include provision of location identifier
(including ECS / E911 information), embedded L2 switch support, inventory
management.
LLDP-MED Capabilities :
LLDP-MED Capabilities describes the neighborhood unit's LLDP-MED capabilities.
The possible capabilities are:
1. LLDP-MED capabilities
2. Network Policy
3. Location Identification
4. Extended Power via MDI - PSE
5. Extended Power via MDI - PD
6. Inventory
7. Reserved
429
Application Type :
Application Type indicating the primary function of the application(s) defined for
this network policy, advertised by an Endpoint or Network Connectivity Device. The
possible application types are shown below.
1. Voice - for use by dedicated IP Telephony handsets and other similar appliances
supporting interactive voice services. These devices are typically deployed on a
separate VLAN for ease of deployment and enhanced security by isolation from
data applications.
2. Voice Signalling - for use in network topologies that require a different policy for
the voice signalling than for the voice media.
3. Guest Voice - to support a separate limited feature-set voice service for guest
users and visitors with their own IP Telephony handsets and other similar appliances
supporting interactive voice services.
4. Guest Voice Signalling - for use in network topologies that require a different
policy for the guest voice signalling than for the guest voice media.
5. Softphone Voice - for use by softphone applications on typical data centric
devices, such as PCs or laptops.
6. Video Conferencing - for use by dedicated Video Conferencing equipment and
other similar appliances supporting real-time interactive video/audio services.
7. Streaming Video - for use by broadcast or multicast based video content
distribution and other similar applications supporting streaming video services that
require specific network policy treatment. Video applications relying on TCP with
buffering would not be an intended use of this application type.
8. Video Signalling - for use in network topologies that require a separate policy for
the video signalling than for the video media.
Policy :
Policy indicates that an Endpoint Device wants to explicitly advertise that the policy
is required by the device. Can be either Defined or Unknown
Unknown: The network policy for the specified application type is currently
unknown.
Defined: The network policy is defined.
430
TAG :
TAG is indicative of whether the specified application type is using a tagged or an
untagged VLAN. Can be Tagged or Untagged.
Untagged: The device is using an untagged frame format and as such does not
include a tag header as defined by IEEE 802.1Q-2003.
Tagged: The device is using the IEEE 802.1Q tagged frame format.
VLAN ID :
VLAN ID is the VLAN identifier (VID) for the port as defined in IEEE 802.1Q-2003. A
value of 1 through 4094 is used to define a valid VLAN ID. A value of 0 (Priority
Tagged) is used if the device is using priority tagged frames as defined by IEEE
802.1Q-2003, meaning that only the IEEE 802.1D priority level is significant and the
default PVID of the ingress port is used instead.
Priority :
Priority is the Layer 2 priority to be used for the specified application type.One of
the eight priority levels (0 through 7).
DSCP :
DSCP is the DSCP value to be used to provide Diffserv node behavior for the
specified application type as defined in IETF RFC 2474. Contain one of 64 code point
values (0 through 63).
Auto-negotiation
Auto-negotiation identifies if MAC/PHY auto-negotiation is supported by the link
partner.
Auto-negotiation status
Auto-negotiation status identifies if auto-negotiation is currently enabled at the
link partner. If Auto-negotiation is supported and Auto-negotiation status is
disabled, the 802.3 PMD operating mode will be determined the operational MAU
type field value rather than by auto-negotiation.
Auto-negotiation Capabilities
Auto-negotiation Capabilities shows the link partners MAC/PHY capabilities.
Buttons
431
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
3-12.3 PoE
This page allows the user to inspect the current status for all PoE ports. The section
show all port Power Over Ethernet Status.
Web Interface
To show LLDP EEE neighbors:
1. Click Monitor ,LLDP, PoE
2. Display Power Over Ethernet Status Information
3. Click Auto-refresh for auto-update web screen
Figure 3-12.3: The LLDP Neighbors EEE information
Parameter description:
Local Port :
The port for this switch on which the LLDP frame was received.
Power Type :
The Power Type represents whether the device is a Power Sourcing Entity (PSE) or
Power Device (PD).
If the Power Type is unknown it is represented as "Reserved".
Power Source :
432
The Power Source represents the power source being utilized by a PSE or PD device.
If the device is a PSE device it can either run on its Primary Power Source or its
Backup Power Source. If it is unknown whether the PSE device is using its Primary
Power Source or its Backup Power Source it is indicated as "Unknown"
If the device is a PD device it can either run on its local power supply or it can use
the PSE as power source. It can also use both its local power supply and the PSE.
If it is unknown what power supply the PD device is using it is indicated as
"Unknown"
Power Priority :
Power Priority represents the priority of the PD device, or the power priority
associated with the PSE type device's port that is sourcing the power. There are
three levels of power priority. The three levels are: Critical, High and Low.
If the power priority is unknown it is indicated as "Unknown"
Maximum Power :
The Maximum Power Value contains a numerical value that indicates the maximum
power in watts required by a PD device from a PSE device, or the minimum power a
PSE device is capable of sourcing over a maximum length cable based on its current
configuration.
The maximum allowed value is 102.3 W. If the device indicates value higher than
102.3 W, it is represented as "reserved"
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
433
Refresh: Click to refresh the page.
434
3-12.4 EEE
By using EEE power savings can be achieved at the expense of traffic latency. This
latency occurs due to that the circuits EEE turn off to save power, need time to boot up
before sending traffic over the link. This time is called "wakeup time". To achieve
minimal latency, devices can use LLDP to exchange information about their respective
tx and rx "wakeup time ", as a way to agree upon the minimum wakeup time they
need.
This page provides an overview of EEE information exchanged by LLDP.
Web Interface
To show LLDP EEE neighbors:
1. Click Monitor ,LLDP, then click EEE to show discover EEE devices
2. Click Refresh for manual update web screen
3. Click Auto-refresh for auto-update web screen
Figure 3-12.4: The LLDP Neighbors EEE information
NOTE: If your network without any devices which enables EEE
function then the table will show “No LLDP EEE information
found”.
Parameter description:
Local Port :
The port on which LLDP frames are received or transmitted.
Tx Tw :
The link partner’s maximum time that transmit path can hold off sending data after
reassertion of LPI.
435
Rx Tw :
The link partner’s time that receiver would like the transmitter to hold off to allow
time for the receiver to wake from sleep.
Fallback Receive Tw :
The link partner’s fallback receive Tw.
A receiving link partner may inform the transmitter of an alternate desired Tw_sys_tx.
Since a receiving link partner is likely to have discrete levels for savings, this
provides the transmitter with additional information that it may use for a more
efficient allocation. Systems that do not implement this option default the value to
be the same as that of the Receive Tw_sys_tx.
Echo Tx Tw :
The link partner's Echo Tx Tw value.
The respective echo values shall be defined as the local link partner’s reflection
(echo) of the remote link partners respective values. When a local link partner
receives its echoed values from the remote link partner it can determine whether or
not the remote link partner has received, registered and processed its most recent
values. For example, if the local link partner receives echoed parameters that do not
match the values in its local MIB, then the local link partner infers that the remote
link partners request was based on stale information.
Echo Rx Tw :
The link partner's Echo Rx Tw value.
Resolved Tx Tw :
The resolved Tx Tw for this link. Note: NOT the link partner
The resolved value that is the actual "tx wakeup time” used for this link (based on
EEE information exchanged via LLDP).
Resolved Rx Tw :
The resolved Rx Tw for this link. Note: NOT the link partner
The resolved value that is the actual "tx wakeup time” used for this link (based on
EEE information exchanged via LLDP).
EEE in Sync
436
Shows whether the switch and the link partner have agreed on wake times.
Red - Switch and link partner have not agreed on wakeup times.
Green - Switch and link partner have agreed on wakeup times.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
437
3-12.5 Port Statistics
Two types of counters are shown. Global counters are counters that refer to the whole
switch, while local counters refer to per port counters for the currently selected switch
Web Interface
To show LLDP Statistics:
1. Click Monitor ,LLDP, then click Port Statistics to show LLDP counters
2. Click Refresh for manual update web screen
3. Click Auto-refresh for auto-update web screen
4. Click Clear to clear all counters
Figure 3-12.5: The LLDP Port Statistics information
Parameter description:
Global Counters
Neighbour entries were last changed at :
438
It also shows the time when the last entry was last deleted or added. It also shows
the time elapsed since the last change was detected.
Total Neighbours Entries Added :
Shows the number of new entries added since switch reboot.
Total Neighbours Entries Deleted :
Shows the number of new entries deleted since switch reboot.
Total Neighbours Entries Dropped :
Shows the number of LLDP frames dropped due to the entry table being full.
Total Neighbours Entries Aged Out :
Shows the number of entries deleted due to Time-To -Live expiring.
Local Counters
The displayed table contains a row for each port. The columns hold the following
information:
Local Port :
The port on which LLDP frames are received or transmitted.
Tx Frames :
The number of LLDP frames transmitted on the port.
Rx Frames :
The number of LLDP frames received on the port.
Rx Errors :
The number of received LLDP frames containing some kind of error.
Frames Discarded :
If an LLDP frame is received on a port, and the switch's internal table has run full,
the LLDP frame is counted and discarded. This situation is known as "Too Many
Neighbours" in the LLDP standard. LLDP frames require a new entry in the table
when the Chassis ID or Remote Port ID is not already contained within the table.
Entries are removed from the table when a given port's link is down, an LLDP
shutdown frame is received, or when the entry ages out.
439
TLVs Discarded :
Each LLDP frame can contain multiple pieces of information, known as TLVs (TLV is
short for "Type Length Value"). If a TLV is malformed, it is counted and discarded.
TLVs Unrecognized :
The number of well-formed TLVs, but with an unknown type value.
Org. Discarded :
The number of organizationally received TLVs.
Age-Outs :
Each LLDP frame contains information about how long time the LLDP information is
valid (age-out time). If no new LLDP frame is received within the age out time, the
LLDP information is removed, and the Age-Out counter is incremented.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Clear: Clears the counters for the selected port.
Refresh: Click to refresh the page.
3-13 Ethernet Services
3-13.1 EVC Statistics
This page provides NNI port traffic statistics for the selected EVC. It also shows counters
for UNI ports of ECEs mapping to the EVC. And the MPLS Pseudo-Wires counters are
included when the PW ID is attached to the selected EVC.
Web Interface
To show Ethernet Statistics:
Click Monitor Ethernet Statistics
Click Refresh for manual update web screen
440
Click Auto-refresh for auto-update web screen
Click Clear to clear all counters
.
Figure 3-13.1: The Ethernet Statistics
Parameter description:
Class
The traffic class for the EVC.
Rx Green
The number of green received.
Tx Green
The number of green transmitted.
Rx Yellow
The number of yellow received.
Tx Yellow
The number of yellow transmitted.
Rx Red
The number of red received.
Green Discarded
441
The number of discarded in the green color.
Yellow Discarded
The number of discarded in the yellow color
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
Clear: Clears the counters for the selected port.
3-14 PTP
This page allows the user to inspect the current PTP clock settings.
Web Interface
To show PTP:
Click Monitor, PTP.
Click Refresh for manual update web screen
Click Auto-refresh for auto-update web screen
Click Clear to clear all counters
.
Figure 3-14: The PTP
442
Parameter description:
PTP External Clock Description
One_PPS_Mode
Shows the current One_pps_mode configured.
1. Output : Enable the 1 pps clock output
2. Input : Enable the 1 pps clock input
3. Disable : Disable the 1 pps clock in/out-put
External Enable
Shows the current External clock output configuration.
1. True : Enable the external clock output
2. False : Disable the external clock output
Adjust Method
Shows the current Frequency adjustment configuration.
1. LTC frequency : Local Time Counter (LTC) frequency control
2. SyncE-DPLL : SyncE DPLL frequency control, if allowed by SyncE
3. Oscillator : Oscillator independent of SyncE for frequency control, if supported by
the HW
4. LTC phase : Local Time Counter (LTC) phase control (assumes that the frequency is
locked by means of SyncE)
Clock Frequency
Shows the current clock frequency used by the External Clock.
The possible range of values are 1 - 25000000 (1 - 25MHz)
443
PTP Clock Description
Inst
Indicates the Instance of a particular Clock Instance [0..3].
Click on the Clock Instance number to monitor the Clock details.
ClkDom
Indicates the Clock domain used by the Instance of a particular Clock Instance [0..3].
Device Type
Indicates the Type of the Clock Instance. There are five Device Types.
1. Ord-Bound - Clock's Device Type is Ordinary-Boundary Clock.
2. P2p Transp - Clock's Device Type is Peer to Peer Transparent Clock.
3. E2e Transp - Clock's Device Type is End to End Transparent Clock.
4. Master Only - Clock's Device Type is Master Only.
5. Slave Only - Clock's Device Type is Slave Only.
Port List
Shows the ports configured for that Clock Instance.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
3-15 PoE
This page allows the user to inspect the current status for all PoE ports.
Web Interface
To Display ECE Statistics in the web interface:
1. Click Monitor, PoE
2. Checked “Auto-refresh”.
3. Click “Refresh” to refresh the port detailed statistics.
444
Figure 3-15: The PoE Statistics
Parameter description:
Local Port
This is the logical port number for this row.
PD Class
Each PD is classified according to a class that defines the maximum power the PD
will use. The PD Class shows the PDs class.
Five Classes are defined:
Class 0: Max. power 15.4 W
Class 1: Max. power 4.0 W
Class 2: Max. power 7.0 W
Class 3: Max. power 15.4 W
Class 4: Max. power 30.0 W
Power Requested
The Power Requested shows the requested amount of power the PD wants to be
reserved.
Power Allocated
The Power Allocated shows the amount of power the switch has allocated for the
445
PD.
Power Used
The Power Used shows how much power the PD currently is using.
Current Used
The Power Used shows how much current the PD currently is using.
Priority
The Priority shows the port's priority configured by the user.
Port Status
The Port Status shows the port's status. The status can be one of the following
values:
PoE not available - No PoE chip found - PoE not supported for the port.
PoE turned OFF - PoE disabled : PoE is disabled by user.
PoE turned OFF - Power budget exceeded - The total requested or used power by
the PDs exceeds the maximum power the Power Supply can deliver, and port(s) with
the lowest priority is/are powered down.
No PD detected - No PD detected for the port.
PoE turned OFF - PD overload - The PD has requested or used more power than the
port can deliver, and is powered down.
PoE turned OFF - PD is off.
Invalid PD - PD detected, but is not working correctly.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
446
3-16 MAC Table
Entries in the MAC Table are shown on this page. The MAC Table contains up to 8192
entries, and is sorted first by VLAN ID, then by MAC address.
Web Interface
To Display MAC Address Table in the web interface:
1. Click Monitor, Dynamic MAC Table.
2. Specify the VLAN and MAC Address.
3. Display MAC Address Table.
Figure 3-16: The MAC Address Table
Parameter description:
Navigating the MAC Table
Each page shows up to 999 entries from the MAC table, default being 20, selected
through the "entries per page" input field. When first visited, the web page will show
the first 20 entries from the beginning of the MAC Table. The first displayed will be the
one with the lowest VLAN ID and the lowest MAC address found in the MAC Table.
The "Start from MAC address" and "VLAN" input fields allow the user to select the
starting point in the MAC Table. Clicking the “Refresh” button will update the
447
displayed table starting from that or the closest next MAC Table match. In addition,
the two input fields will - upon a “Refresh” button click - assume the value of the first
displayed entry, allowing for continuous refresh with the same start address.
The >> will use the last entry of the currently displayed VLAN/MAC address pairs as a
basis for the next lookup. When the end is reached the text "No more entries" is shown
in the displayed table. Use the l<< button to start over.
MAC Table Columns
Switch (stack only)
The stack unit where the entry is learned.
Type :
Indicates whether the entry is a static or a dynamic entry.
VLAN :
The VLAN ID of the entry.
MAC address :
The MAC address of the entry.
Port Members :
The ports that are members of the entry.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Clear: Clears the counters for the selected port.
Refresh: Click to refresh the page.
|<<: Updates the system log entries to the first available entry ID
>> : Updates the system log entry to the next available entry ID
448
NOTE:
00-40-C7-73-01-29 : your switch MAC address (for IPv4)
33-33-00-00-00-01 : Destination MAC (for IPv6 Router
Advertisement) (reference IPv6 RA.JPG)
33-33-00-00-00-02 : Destination MAC (for IPv6 Router
Solicitation) (reference IPv6 RS.JPG)
33-33-FF-73-01-29 : Destination MAC (for IPv6 Neighbor
Solicitation) (reference IPv6 DAD.JPG)
33-33-FF-A8-01-01: your switch MAC address (for IPv6 global IP)
FF-FF-FF-FF-FF-FF: for Broadcast.
449
3-17 VLANs
3-17.1 Membership
This page provides an overview of membership status of VLAN users.
The ports belong to the currently selected stack unit, as reflected by the page header.
Web Interface
To configure VLAN membership configuration in the web interface:
1. Click Monitor, VLANs, VLAN membership.
2. Scroll the bar to choice which VLANs would like to show up.
3. Click Refresh to update the state.
Figure 3-17.1: VLAN Membership Status for Combined users
Parameter description:
VLAN USER
VLAN User module uses services of the VLAN management functionality to
configure VLAN memberships and VLAN port configurations such as PVID and
UVID. Currently we support the following VLAN user types:
CLI/Web/SNMP : These are referred to as static.
NAS : NAS provides port-based authentication, which involves communications
between a Supplicant, Authenticator, and an Authentication Server.
MVRP : Multiple VLAN Registration Protocol (MVRP) allows dynamic registration
and deregistration of VLANs on ports on a VLAN bridged network.
450
Voice VLAN : Voice VLAN is a VLAN configured specially for voice traffic typically
originating from IP phones.
MVR : MVR is used to eliminate the need to duplicate multicast traffic for
subscribers in each VLAN. Multicast traffic for all channels is sent only on a single
(multicast) VLAN.
MSTP : The 802.1s Multiple Spanning Tree protocol (MSTP) uses VLANs to create
multiple spanning trees in a network, which significantly improves network resource
utilization while maintaining a loop-free environment.
VLAN ID
VLAN ID for which the Port members are displayed.
Port Members
A row of check boxes for each port is displayed for each VLAN ID.
If a port is included in a VLAN, an image will be displayed.
If a port is included in a Forbidden port list, an image will be displayed.
If a port is included in a Forbidden port list and dynamic VLAN user register VLAN
on same Forbidden port, then conflict port will be displayed as .
VLAN Membership
The VLAN Membership Status Page shall show the current VLAN port members for
all VLANs configured by a selected VLAN User (selection shall be allowed by a
Combo Box). When ALL VLAN Users are selected, it shall show this information for
all the VLAN Users, and this is by default. VLAN membership allows the frames
classified to the VLAN ID to be forwarded on the respective VLAN member ports.
Navigating the VLAN Monitor page
Each page shows up to 99 entries from the VLAN table, default being 20, selected
through the "entries per page" input field. When first visited, the web page will
show the first 20 entries from the beginning of the VLAN Table. The first displayed
will be the one with the lowest VLAN ID found in the VLAN Table.
The "VLAN" input fields allow the user to select the starting point in the VLAN Table.
Clicking the “Refresh” button will update the displayed table starting from that or
the closest next VLAN Table match. The “ >> ”will use the last entry of the currently
displayed VLAN entry as a basis for the next lookup. When the end is reached the
text "No more entries" is shown in the displayed table. Use the “ |<< ”button to
start over.
451
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
452
3-17.2 Port
The function Port Status gathers the information of all VLAN status and reports it by
the order of Static NAS MVRP MVP Voice VLAN MSTP GVRP Combined.
Web Interface
To Display VLAN Port Status in the web interface:
1. Click Monitor, VLAN Port Status.
2. Specify the Static NAS MVRP MVP Voice VLAN MSTP GVRP Combined.
3. Display Port Status information.
Figure 3-17.2: The VLAN Port Status for Static user
Parameter description:
VLAN USER
VLAN User module uses services of the VLAN management functionality to configure
VLAN memberships and VLAN port configuration such as PVID, UVID. Currently we
support following VLAN User types:
CLI/Web/SNMP : These are referred to as static.
NAS : NAS provides port-based authentication, which involves communications
between a Supplicant, Authenticator, and an Authentication Server.
Voice VLAN : Voice VLAN is a VLAN configured specially for voice traffic typically
453
originating from IP phones.
MVR : MVR is used to eliminate the need to duplicate multicast traffic for subscribers
in each VLAN. Multicast traffic for all channels is sent only on a single (multicast) VLAN.
MSTP : The 802.1s Multiple Spanning Tree protocol (MSTP) uses VLANs to create
multiple spanning trees in a network, which significantly improves network resource
utilization while maintaining a loop-free environment.
Port :
The logical port for the settings contained in the same row.
Port Type :
Shows the Port Type. Port type can be any of Unaware, C-port, S-port, Custom
S-port.
If Port Type is Unaware, all frames are classified to the Port VLAN ID and tags are
not removed. C-port is Customer Port. S-port is Service port. Custom S-port is
S-port with Custom TPID.
Ingress Filtering :
Shows the ingress filtering on a port. This parameter affects VLAN ingress
processing. If ingress filtering is enabled and the ingress port is not a member of
the classified VLAN, the frame is discarded.
Frame Type :
Shows whether the port accepts all frames or only tagged frames. This parameter
affects VLAN ingress processing. If the port only accepts tagged frames, untagged
frames received on that port are discarded.
Port VLAN ID :
Shows the Port VLAN ID (PVID) that a given user wants the port to have.
The field is empty if not overridden by the selected user.
Tx Tag :
Shows egress filtering frame status whether tagged or untagged.
UVID :
454
Shows UVID (untagged VLAN ID). Port's UVID determines the packet's behavior at
the egress side.
Conflicts :
Shows status of Conflicts whether exists or not. When a Volatile VLAN User requests
to set VLAN membership or VLAN port configuration, the following conflicts can
occur:
Functional Conflicts between features.
Conflicts due to hardware limitation.
Direct conflict between user modules.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
455
3-18 VCL
3-18.1 MAC-based VLAN
This section shows MAC-based VLAN entries configured by various MAC-based VLAN
users. Currently we support following VLAN User types:
CLI/Web/SNMP: These are referred to as static.
NAS: NAS provides port-based authentication, which involves communications
between a Supplicant, Authenticator, and an Authentication Server.
Web Interface
To Display MAC-based VLAN configuration in the web interface:
1. Click Monitor, MAC-based VLAN Status.
2. Specify the Static, NAS, Combined.
3. Display MAC-based information.
Figure 3-18.1: The MAC-based VLAN Membership Status for User Static
Parameter description:
MAC Address :
Indicates the MAC address.
VLAN ID :
Indicates the VLAN ID.
456
Port Members :
Port members of the MAC-based VLAN entry.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
457
3-18.2 Protocol-based VLAN
3-18.2.1 Protocol to Group
This page shows you the protocols to Group Name (unique for each Group) mapping
entries for the switch.
Web Interface
To Display Protocol-based VLAN configuration in the web interface:
1. Click Monitor, VCL, Protocol to Group.
2. Checked “Auto-refresh”.
3. Click “Refresh” to refresh the port detailed statistics.
Figure 3-18.2.1: The MAC-based VLAN Membership Status for User Static
Parameter description:
Frame Type :
Frame Type can have one of the following values:
1. Ethernet
2. LLC
3. SNAP
NOTE:
On changing the Frame type field, valid value of the following
text field will vary depending on the new frame type you
458
selected.
Value :
Valid value that can be entered in this text field depends on the option selected
from the preceding Frame Type selection menu.
Below is the criteria for three different Frame Types:
1. For Ethernet: Values in the text field when Ethernet is selected as a Frame Type is
called etype. Valid values for etype ranges from 0x0600-0xffff
2. For LLC: Valid value in this case is comprised of two different sub-values.
a. DSAP: 1-byte long string (0x00-0xff)
b. SSAP: 1-byte long string (0x00-0xff)
3. For SNAP: Valid value in this case also is comprised of two different sub-values.
a. OUI: OUI (Organizationally Unique Identifier) is value in format of xx-xx-xx where
each pair (xx) in string is a hexadecimal value ranges from 0x00-0xff.
b. PID: If the OUI is hexadecimal 000000, the protocol ID is the Ethernet type
(EtherType) field value for the protocol running on top of SNAP; if the OUI is an OUI
for a particular organization, the protocol ID is a value assigned by that organization
to the protocol running on top of SNAP.
In other words, if value of OUI field is 00-00-00 then value of PID will be etype
(0x0600-0xffff) and if value of OUI is other than 00-00-00 then valid value of PID will
be any value from 0x0000 to 0xffff.
Group Name :
A valid Group Name is a unique 16-character long string for every entry which
consists of a combination of alphabets (a-z or A-Z) and integers (0-9).
NOTE:
special character and underscore(_) are not allowed.
Buttons
459
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
460
3-18.2.2 Group to VLAN
This page shows you the configured Group Name to a VLAN for the switch.
Web Interface
To Display Group to VLAN configuration in the web interface:
1. Click Monitor, VCL, Group to VLAN.
2. Checked “Auto-refresh”.
3. Click “Refresh” to refresh the port detailed statistics.
Figure 3-17.2.2: The MAC-based VLAN Membership Status for User Static
Parameter description:
Group Name :
A valid Group Name is a string at the most 16 characters which consists of a
combination of alphabets (a-z or A-Z) and integers(0-9), no special character is
allowed. Whichever Group name you try map to a VLAN must be present in
Protocol to Group mapping table and must not be pre-used by any other existing
mapping entry on this page.
VLAN ID :
Indicates the ID to which Group Name will be mapped. A valid VLAN ID ranges from
1-4095.
Port Members :
A row of check boxes for each port is displayed for each Group Name to VLAN ID
mapping. To include a port in a mapping, check the box. To remove or exclude the
461
port from the mapping, make sure the box is unchecked. By default, no ports are
members, and all boxes are unchecked.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
462
3-18.3 IP Subnet-based VLAN
The page shows IP subnet-based VLAN entries. This page shows only static entries.
Web Interface
To Display MAC-based VLAN configuration in the web interface:
1. Click Monitor, VCL, and IP Subnet-based VLAN.
2. Checked “Auto-refresh”.
3. Click “Refresh” to refresh the port detailed statistics.
Figure 3-17.3: The MAC-based VLAN Membership Status for User Static
Parameter description:
VCE ID :
Indicates the index of the entry. It is user configurable. Its value ranges from 0-128.
If a VCE ID is 0, application will auto-generate the VCE ID for that entry. Deletion
and lookup of IP subnet-based VLAN are based on VCE ID.
IP Address :
Indicates the IP address.
Mask Length :
Indicates the network mask length.
VLAN ID :
Indicates the VLAN ID. VLAN ID can be changed for the existing entries.
463
Port Members :
A row of check boxes for each port is displayed for each IP subnet-based VLAN
entry. To include a port in a IP subnet-based VLAN, check the box. To remove or
exclude the port from the IP subnet-based VLAN, make sure the box is unchecked.
By default, no ports are members, and all boxes are unchecked.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
465
This field shows the current owner of the sFlow configuration. It assumes one of
three values as follows:
• If sFlow is currently unconfigured/unclaimed, Owner contains <none>.
• If sFlow is currently configured through Web or CLI, Owner contains <Configured
through local management>.
• If sFlow is currently configured through SNMP, Owner contains a string identifying
the sFlow receiver.`
IP Address/Hostname
The IP address or hostname of the sFlow receiver.
Timeout
The number of seconds remaining before sampling stops and the current sFlow
owner is released.
Tx Successes
The number of UDP datagrams successfully sent to the sFlow receiver.
Tx Errors
The number of UDP datagrams that has failed transmission.
The most common source of errors is invalid sFlow receiver IP/hostname
configuration. To diagnose, paste the receiver's IP address/hostname into the Ping
Web page (Diagnostics → Ping/Ping6).
Flow Samples
The total number of flow samples sent to the sFlow receiver.
Counter Samples
The total number of counter samples sent to the sFlow receiver.
Port Statistics
Port
The port number for which the following statistics applies.
Rx and Tx Flow Samples
The number of flow samples sent to the sFlow receiver originating from this port.
466
Here, flow samples are divided into Rx and Tx flow samples, where Rx flow samples
contains the number of packets that were sampled upon reception (ingress) on the
port and Tx flow samples contains the number of packets that were sampled upon
transmission (egress) on the port.
Counter Samples
The total number of counter samples sent to the sFlow receiver originating from this
port.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
Clear Receiver: Clears the sFlow receiver counters.
Clear Ports: Clears the per-port counters.
467
3-20 UDLD
This page displays the UDLD status of the ports
Web Interface
To Display UDLD in the web interface:
Click Monitor, UDLD
Display UDLD information.
Figure 3-20: The UDLD
Parameter description:
UDLD port status
UDLD Admin State
The current port state of the logical port, Enabled if any of state(Normal,Aggressive)
is Enabled.
Device ID(local)
The ID of Device.
Device Name(local)
Name of the Device.
Bidirectional State
The current state of the por
468
Neighbour Status
Port
The current port of neighbour device.
Device ID
The current ID of neighbour device.
Link Status
The current link status of neighbour port.
Device Name
Name of the Neighbour Device.
Buttons
Auto-refresh: Check this box to refresh the page automatically. Automatic refresh
occurs every 3 seconds.
Refresh: Click to refresh the page.
469
Chapter 4. Diagnostics
This chapter provides a set of basic system diagnosis. It let users know that
whether the system is health or needs to be fixed. The basic system check
includes ICMP Ping, Link OAM, ICMPv6, and VeriPHY Cable Diagnostics.
4-1 Ping
This section allows you to issue ICMP PING packets to troubleshoot IPv6 connectivity
issues.
Web Interface
To configure an ICMP PING Configuration in the web interface:
1. Specify ICMP PING IP Address.
2. Specify ICMP PING Size.
3. Click Start.
Figure 4-1: The ICMP Ping
470
Parameter description:
IP Address :
To set the IP Address of device what you want to ping it.
Ping Length:
The payload size of the ICMP packet. Values range from 2 bytes to 1452 bytes.
Ping Count:
The count of the ICMP packet. Values range from 1 time to 60 times.
Ping Interval:
The interval of the ICMP packet. Values range from 0 second to 30 seconds.
Egress Interface (Only for IPv6):
The VLAN ID (VID) of the specific egress IPv6 interface which ICMP packet goes.
The given VID ranges from 1 to 4094 and will be effective only when the
corresponding IPv6 interface is valid.
When the egress interface is not given, PING6 finds the best match interface for
destination.
Do not specify egress interface for loopback address.
Do specify egress interface for link-local or multicast address.
Start:
Click the “Start” button then the switch will start to ping the device using ICMP
packet size what set on the switch.
471
After you press , 5 ICMP packets are transmitted, and the sequence number and
roundtrip time are displayed upon reception of a reply. The page refreshes
automatically until responses to all packets are received, or until a timeout occurs.
PING6 server ::10.10.132.20
64 bytes from ::10.10.132.20: icmp_seq=0, time=0ms
64 bytes from ::10.10.132.20: icmp_seq=1, time=0ms
64 bytes from ::10.10.132.20: icmp_seq=2, time=0ms
64 bytes from ::10.10.132.20: icmp_seq=3, time=0ms
64 bytes from ::10.10.132.20: icmp_seq=4, time=0ms
Sent 5 packets, received 5 OK, 0 bad
472
4-2 Ping6
This section allows you to issue ICMPv6 PING packets to troubleshoot IPv6
connectivity issues.
Web Interface
To configure an ICMPv6 PING Configuration in the web interface:
1. Specify ICMPv6 PING IP Address.
2. Specify ICMPv6 PING Size.
3. Click Start.
Figure 4-2: The ICMPv6 Ping
Parameter description:
IP Address :
The destination IP Address with IPv6
Ping Length :
The payload size of the ICMP packet. Values range from 2 bytes to 1452 bytes.
Ping Count :
473
The count of the ICMP packet. Values range from 1 time to 60 times.
Ping Interval :
The interval of the ICMP packet. Values range from 0 second to 30 seconds.
Egress Interface (Only for IPv6) :
The VLAN ID (VID) of the specific egress IPv6 interface which ICMP packet goes.
The given VID ranges from 1 to 4094 and will be effective only when the corresponding IPv6
interface is valid.
When the egress interface is not given, PING6 finds the best match interface for destination.
Do not specify egress interface for loopback address.
Do specify egress interface for link-local or multicast address.
Start:
Click the “Start” button then the switch will start to ping the device using ICMPv6
packet size what set on the switch.
After you press, 5 ICMPv6 packets are transmitted, and the sequence number and
roundtrip time are displayed upon reception of a reply. The page refreshes
automatically until responses to all packets are received, or until a timeout occurs.
PING server 10.10.132.20
64 bytes from 10.10.132.20: icmp_seq=0, time=0ms
64 bytes from 10.10.132.20: icmp_seq=1, time=0ms
64 bytes from 10.10.132.20: icmp_seq=2, time=0ms
64 bytes from 10.10.132.20: icmp_seq=3, time=0ms
64 bytes from 10.10.132.20: icmp_seq=4, time=0ms
Sent 5 packets, received 5 OK, 0 bad
You can configure the following properties of the issued ICMP packets:
474
4-3 VeriPHY
This section is used for running the VeriPHY Cable Diagnostics. Press to run the
diagnostics. This will take approximately 5 seconds. If all ports are selected, this can
take approximately 15 seconds. When completed, the page refreshes automatically,
and you can view the cable diagnostics results in the cable status table. Note that
VeriPHY is only accurate for cables of length 7 -140 meters.10 and 100 Mbps ports will
be linked down while running VeriPHY. Therefore, running VeriPHY on a 10 or 100
Mbps management port will cause the switch to stop responding until VeriPHY is
complete.
Web Interface
To configure a VeriPHY Cable Diagnostics Configuration in the web interface:
1. Specify Port which want to check.
2. Click Start.
Figure 4-3: The VeriPHY
Parameter description:
Port :
475
The port where you are requesting VeriPHY Cable Diagnostics.
Cable Status :
Port: Port number.
Pair: The status of the cable pair.
Length: The length (in meters) of the cable pair.
476
4-4 Traceroute
This page allows you to issue ICMP, TCP, or UDP packets to diagnose network
connectivity issues.
Web Interface
To configure an ICMPv6 PING Configuration in the web interface:
1. Specify traceroute IP Address.
2. Specify traceroute Size.
3. Click Start.
Figure 4-4: The Traceroute
Parameter description:
Protocol :
The protocol(ICMP, UDP, TCP) packets to send.
IP Address :
The destination IP Address.
Wait Time :
Set the time (in seconds) to wait for a response to a probe (default 5.0 sec). Values
477
range from 1 to 60. The payload size of the ICMP packet. Values range from 2 bytes
to 1452 bytes.
Max TTL :
Specifies the maximum number of hops (max time-to-live value) traceroute will
probe. Values range from 1 to 255. The default is 30.
Probe Count :
Sets the number of probe packets per hop. Values range from 1 to 10. The default is
3.
478
4-5 Link OAM
4-5.1 MIB Retrieval
This page provides detailed OAM traffic statistics for a specific switch port. Use the port
select box to select which switch port details to display.
The displayed counters represent the total number of OAM frames received and
transmitted for the selected port. Discontinuities of these counter can occur at
re-initialization of the management system.
Web Interface
To configure the Statistics in the web interface:
1. Click Monitor, Link OAM and Statistics.
2. To display the Statistics.
Figure 4-5.1: MIB Retrieval
Parameter description:
Ping
This page allows you to issue ICMP PING packets to troubleshoot IP connectivity
issues. After you press ”Start” , ICMP packets are transmitted, and the sequence
number and round trip time are displayed upon reception of a reply. The amount of
479
data received inside of an IP packet of type ICMP ECHO_REPLY will always be 8
bytes more than the requested data space (the ICMP header). The page refreshes
automatically until responses to all packets are received, or until a timeout occurs.
PING server 10.10.132.20, 56 bytes of data.
64 bytes from 10.10.132.20: icmp_seq=0, time=0ms
64 bytes from 10.10.132.20: icmp_seq=1, time=0ms
64 bytes from 10.10.132.20: icmp_seq=2, time=0ms
64 bytes from 10.10.132.20: icmp_seq=3, time=0ms
64 bytes from 10.10.132.20: icmp_seq=4, time=0ms
Sent 5 packets, received 5 OK, 0 bad
Link OAM MIB Retrieval
This page allows you to retrieve the local or remote OAM MIB variable data on a
particular port. Select the appropriate radio button and enter the port number of
the switch to retrieve the content of interest. Click on “Star” to retrieve the content.
Click on “New Retrieval” to retrieve another content of interest.
Ping6
This page allows you to issue ICMPv6 PING packets to troubleshoot IPv6
connectivity issues. After you press “Start” , ICMPv6 packets are transmitted, and
the sequence number and round trip time are displayed upon reception of a
reply. The page refreshes automatically until responses to all packets are
received, or until a timeout occurs.
PING6 server ff02::2, 56 bytes of data.
64 bytes from fe80::219:5bff:fe2f:b47: icmp_seq=0, time=10ms
64 bytes from fe80::215:58ff:feed:69dd: icmp_seq=0, time=10ms
64 bytes from fe80::219:5bff:fe2f:b47: icmp_seq=1, time=0ms
64 bytes from fe80::215:58ff:feed:69dd: icmp_seq=1, time=0ms
64 bytes from fe80::219:5bff:fe2f:b47: icmp_seq=2, time=0ms
64 bytes from fe80::215:58ff:feed:69dd: icmp_seq=2, time=0ms
64 bytes from fe80::219:5bff:fe2f:b47: icmp_seq=3, time=0ms
64 bytes from fe80::215:58ff:feed:69dd: icmp_seq=3, time=0ms
64 bytes from fe80::219:5bff:fe2f:b47: icmp_seq=4, time=0ms
480
64 bytes from fe80::215:58ff:feed:69dd: icmp_seq=4, time=0ms
Sent 5 packets, received 10 OK, 0 bad
You can configure the following properties of the issued ICMP packets:
IP Address
The destination IP Address.
Ping Length
The payload size of the ICMP packet. Values range from 2 bytes to 1452 bytes.
Ping Count
The count of the ICMP packet. Values range from 1time to 60 times.
Ping Interval
The interval of the ICMP packet. Values range from 0second to 30 seconds.
Egress Interface (Only for IPv6)
The VLAN ID (VID) of the specific egress IPv6 interface which ICMP packet goes.
The given VID ranges from 1 to 4094 and will be effective only when the
corresponding IPv6 interface is valid.
When the egress interface is not given, PING6 finds the best match interface for
destination.
Do not specify egress interface for loopback address.
Do specify egress interface for link-local or multicast address.
Traceroute
This page allows you to issue ICMP, TCP, or UDPpackets to diagnose network
connectivity issues. After you press “Start”, Traceroute sends packets with gradually
increasing TTL value, starting with TTL value of 1. The first router receives the packet,
decrements the TTL value and drops the packet because it then has TTL value zero.
The router sends an ICMP Time Exceeded message back to the source. The next set
of packets are given a TTL value of 2, so the first router forwards the packets, but the
second router drops them and replies with ICMP Time Exceeded. Proceeding in this
way, traceroute uses the returned ICMP Time Exceeded messages to build a list of
routers that packets traverse, until the destination is reached and returns an ICMP
Echo Reply message.
traceroute to 202.39.253.11 (202.39.253.11), 30 hops max, 40 byte packets
1 192.168.10.254 ae-2-3508.edge4.Atlanta2.Level3.net. (192.168.10.254) 10 ms 10
ms 10 ms
2 59-125-13-254.HINET-IP.hinet.net. (59.125.13.254) 20 ms 20 ms 20 ms
3 h146.s228.ts.hinet.net. (168.95.228.146) 20 ms 10 ms 20 ms
4 tchn-3011.hinet.net. (220.128.16.194) 20 ms TCHN-3112.hinet.net. (220.128.17.142)
20 ms tchn-3011.hinet.net. (220.128.16.202) 20 ms
5 TPDT-3012.hinet.net. (220.128.17.6) 20 ms TPDT-3011.hinet.net. (220.128.16.10)
20 ms TPDT-3012.hinet.net. (220.128.17.6) 40 ms
6 CHCH-3112.hinet.net. (220.128.2.13) 20 ms tchn-3011.hinet.net. (220.128.1.9) 10
ms CHCH-3112.hinet.net. (220.128.2.13) 30 ms
7 211.22.41.237 CHCH-3112.hinet.net. (211.22.41.237) 20 ms 30 ms 30 ms
481
8 202-39-253-11.HINET-IP.hinet.net. (202.39.253.11) 10 ms 10 ms
You can configure the following properties:
Protocol
The protocol(ICMP, UDP, TCP) packets to send.
IP Address
The destination IP Address.
Wait Time
Set the time (in seconds) to wait for a response to a probe (default 5.0 sec). Values
range from 1 to 60. The payload size of the ICMP packet. Values range from 2bytes
to 1452 bytes.
Max TTL
Specifies the maximum number of hops (max time-to-live value) traceroute will
probe. Values range from 1 to 255. The default is 30.
Probe Count
Sets the number of probe packets per hop. Values range from 1 to 10. The default is
3.
Buttons
Start: Click to start transmitting ICMP packets.
New Ping: Click to re-start diagnostics with PING.
482
Chapter 5. Maintenance
This chapter describes the entire switch Maintenance configuration tasks to
enhance the performance of local network including Restart Device, Firmware
upgrade, Save/Restore, Import/Export.
5-1 Restart Device
This section describes how to restart switch for any maintenance needs. Any
configuration files or scripts that you saved in the switch should still be available
afterwards.
Web Interface
To configure a Restart Device Configuration in the web interface:
1. Chick Restart Device.
2. Click Yes.
Figure 5-1: Restart Device
483
Parameter description:
Restart Device :
You can restart the switch on this page. After restart, the switch will boot normally.
Buttons:
Yes – Click to “Yes” then the device will restart.
No- Click to undo any restart action.
5-2 Reboot Schedule
This page allows user to schedule the time to reboot the switch.
Web Interface
To configure a Reboot Schedule in the web interface:
1. Chick Reboot Schedule
2. Set the parameters
3. Click Apply.
Figure 5-2: Reboot Schedule
Parameter description:
Mode
484
Indicates the reboot scheduling mode operation. Possible modes are:
Enabled: Enable switch reboot scheduling.
Disabled: Disable switch reboot scheduling.
Week Day
The day to reboot this switch.
Reboot Time
The time to reboot the switch.
Buttons:
Apply–Click to save changes.
Reset–Click to undo any changes made locally and revert to previously saved
values.
485
5-3 Factory Defaults
This section describes how to reset the Switch configuration to Factory Defaults. Any
configuration files or scripts will recover to factory default values.
Web Interface
To configure a Factory Defaults Configuration in the web interface:
1. Chick Factory Defaults.
2. Click Yes.
Figure 5-2: The Factory Defaults
Parameter description:
Buttons:
Yes – Click to “Yes” button to reset the configuration to Factory Defaults.
No- Click to to return to the Port State page without resetting the configuration.
486
5-4 Firmware
This section describes how to upgrade Firmware. The Switch can be enhanced with
more value-added functions by installing firmware upgrades.
5-4.1 Firmware upgrade
This page facilitates an update of the firmware controlling the switch..
Web Interface
To configure a Firmware Upgrade Configuration in the web interface:
1. Chick Browser to select Maintenance/Software in you device.
2. Click Download.
Figure 5-4.1 The firmware Download
Parameter description:
Browse :
Click the “Browse...” button to search the Firmware URL and filename.
Brows
e...
487
NOTE: This page facilitates an update of the firmware controlling
the switch. Uploading software will update all managed switches
to the location of a software image and click. After the software
image is uploaded, a page announces that the firmware update
is initiated. After about a minute, the firmware is updated and all
managed switches restart. the switch restarts.
W
ARNING
:
While the firmware is being updated, Web access
appears to be defunct. The front LED flashes Green/Off with a
frequency of 10 Hz while the firmware update is in progress. Do
not restart or power off the device at this time or the switch may
fail to function afterwards.
488
5-4.2 Firmware Selection
This page provides information about the active and alternate (backup) firmware
images in the device, and allows you to revert to the alternate image.
The web page displays two tables with information about the active and alternate
firmware images.
Note:
1. In case the active firmware image is the alternate image, only the "Active
Image" table is shown. In this case, the Activate Alternate Image button is
also disabled.
2. If the alternate image is active (due to a corruption of the primary image
or by manual intervention), uploading a new firmware image to the device
will automatically use the primary image slot and activate this.
3. The firmware version and date information may be empty for older
firmware releases. This does not constitute an error.
Web Interface
To configure a Firmware Upgrade Configuration in the web interface:
1. Chick Browser to select Maintenance/Software in you device.
2. Click Image Select.
Figure 5-4.2 The Firmware selection
489
Image Information
Image
The flash index name of the firmware image. The name of primary (preferred) image
is image, the alternate image is named image.bk.
Version
The version of the firmware image.
Date
The date where the firmware was produced.
Buttons
Activate Alternate Image: Click to use the “Activate Alternate Image”. This button
may be disabled depending on system state.
Cancel: Cancel activating the backup image. Navigates away from this page.
490
5-5 Configuration
The switch stores its configuration in a number of text files in CLI format. The files are
either virtual (RAM-based) or stored in flash on the switch.
There are three system files:
running-config: A virtual file that represents the currently active configuration
on the switch. This file is volatile.
startup-config: The startup configuration for the switch, read at boot time.
default-config: A read-only file with vendor-specific configuration. This file is
read when the system is restored to default settings.
It is also possible to store up to two other files and apply them to running-config,
thereby switching configuration.
5-5.1 Save startup-config
This copy running-config to startup-config, thereby ensuring that the currently active
configuration will be used at the next reboot.
Web Interface
To save running configuration in the web interface:
1. Chick Browser to select Maintenance/Configuration in you device.
2. Click Apply Startup-Config Select.
Figure 5-5.1: The Save Startup Configuration
491
Parameter description:
Buttons :
Save Configuration: Click to save configuration, the running configuration will be
written to flash memory for system boot up to load this startup configuration file.
492
5-5.2 Download
The switch stores its configuration in a number of text files in CLI format. The files are
either virtual (RAM-based) or stored in flash on the switch.
The available files are:
running-config: A virtual file that represents the currently active configuration on the
switch. This file is volatile.
startup-config: The startup configuration for the switch, read at boot time. If this file
doesn't exist at boot time, the switch will start up in default configuration.
default-config: A read-only file with vendor-specific configuration. This file is read
when the system is restored to default settings.
Up to 99 other files, typically used for configuration backups or alternative
configurations.
Web Interface
To download configuration in the web interface:
1. Chick Browser to select Maintenance/Configuration in you device.
2. Click Download Select.
Figure 5-5.2: Download
Parameter
Save startup-config
493
This copies running-config to startup-config, thereby ensuring that the currently
active configuration will be used at the next reboot.
Download
It is possible to download any of the files on the switch to the web browser. Select
the file and click “Download Configuration”.
Download of running-config may take a little while to complete, as the file must be
prepared for download.
Upload
It is possible to upload a file from the web browser to all the files on the switch,
except default-configwhich is read-only.
Select the file to upload, select the destination file on the target, then click “Upload
Configuration”.
If the destination is running-config, the file will be applied to the switch configuration.
This can be done in two ways:
Replace mode: The current configuration is fully replaced with the configuration in the
uploaded file.
Merge mode: The uploaded file is merged into running-config.
If the flash file system is full (i.e. contains default-config and 100 other files, usually
includingstartup-config), it is not possible to create new files. Instead an existing file
must be overwritten or another file must be deleted.
Activate
It is possible to activate any of the configuration files present on the switch, except
for running-config which represents the currently active configuration.
Select the file to activate and click “Activate Configuration”. This will initiate the
process of completely replacing the existing configuration with that of the selected
file.
Delete
It is possible to delete any of the writable files stored in flash,
including startup-config. If this is done and the switch is rebooted without a prior
Save operation, this effectively resets the switch to default configuration.
494
5-5.3 Upload
The configuration upload function will be backuped and saved configuration from the
switch’s configuration into the running web browser PC.
It is possible to upload any of the files on the switch to the web browser. Select the
file and click Upload of running-config may take a little while to complete, as the file
must be prepared for upload.
Web Interface
To upload configuration in the web interface:
1. Chick Browser to select Maintenance/Configuration in you device.
2. Click upload Select.
Figure 5-5.3: Configuration upload
There are three system files:
1. running-config: A virtual file that represents the currently active configuration on the
switch. This file is volatile.
2. startup-config: The startup configuration for the switch, read at boot time.
3. default-config: A read-only file with vendor-specific configuration. This file is read
when the system is restored to default settings.
495
Parameter description:
Buttons :
Upload Configuration: Click the “Upload” button then the running web
management PC will start to upload the configuration from the managed switch
configuration into the location PC, user can configure web browser’s upload file
path to keep configuration file.
496
5-5.4 Activate
The switch stores its configuration in a number of text files in CLI format. The files are
either virtual (RAM-based) or stored in flash on the switch.
The available files are:
running-config: A virtual file that represents the currently active configuration on the
switch. This file is volatile.
startup-config: The startup configuration for the switch, read at boot time. If this file
doesn't exist at boot time, the switch will start up in default configuration.
default-config: A read-only file with vendor-specific configuration. This file is read when
the system is restored to default settings.
Up to 99 other files, typically used for configuration backups or alternative
configurations.
Web Interface
To activate configuration in the web interface:
1. Chick Browser to select Maintenance/Configuration in you device.
2. Click Activate Select.
Figure 5-5.4: Configuration Activation
There are two system files:
1. default-config: A read-only file with vendor-specific configuration. This file is read
when the system is restored to default settings.
497
2. startup-config: The startup configuration for the switch, read at boot time.
Parameter description:
Buttons :
Activate Configuration: Click the “Activate” button then the default-config or
startup-config file will be activated and to be this switch's running configuration.
498
5-5.5 Delete
It is possible to delete any of the writable files stored in flash, including startup-config.
If this is done and the switch is rebooted without a prior save operation, this
effectively resets the switch to default configuration.
Web Interface
To delete configuration in the web interface:
1. Chick Browser to select Maintenance/Configuration in you device.
2. Click Delete Select.
Figure 5-5.5: Delete Configuration
There is one system files:
startup-config: The startup configuration for the switch, read at boot time.
Parameter description:
Buttons :
Delete Configuration: Click the “Delete” button then the startup-config file will be
deleted, this effectively resets the switch to default configuration.
499
5-6 Server Report
It is possible to download server report file on the switch to the web browser.
Download of server-report may take a little while to complete, as the file must be
prepared for download.
Web Interface
To delete configuration in the web interface:
1. Chick Browser to select Maintenance/Configuration in you device.
2. Click Server Report
Figure 5-6: Server Report