MSI AP1622ET-B10374G50XXASXH User Manual

Wind Top AP1622

All-in-One (AIO) PC

MS-A613 System

G52-A6131X6

Preface

ii iii

Wind Top Series

Preface

ii iii

Wind Top Series

Contents

Copyright Notice ��iii

Trademarks ��iii

Revision ��iii

Upgrade and Warranty �� iv

Acquisition of Replaceable Parts �� iv

Technical Support �� iv

Green Product Features �� iv

Environmental Policy ��v

Chemical Substances Information ��v

Battery Information ��v

Safety Instructions �� vi

CE Conformity ��viii

FCC-B Radio Frequency Interference Statement ��viii

WEEE Statement �� ix

1. Overview ...................................................... 1-1

Packing Contents ��1-2

System Overview ��1-3

System Speci󰘰cations ��1-9

Component Replacement & Upgrade ��1-11

2. Getting Started ............................................. 2-1

Safety & Comfort Tips ��2-2

Hardware Setup ��2-3

3. System Operations ....................................... 3-1

System Booting Setup for the 󰘰rst time ��3-2

Touch Panel Calibration (Only for single-touch model)��3-3

Network Connection under Windows ��3-5

Power Management ��3-10

System Recovery Tool ��3-12

Appendix A. Troubleshooting ............................ A-1

Preface

ii iii

Wind Top Series

Preface

ii iii

Wind Top Series

Copyright Notice

The material in this document is the intellectual property of MICRO-STAR INTER-

NATIONAL� We take every care in the preparation of this document, but no guar-

antee is given as to the correctness of its contents� Our products are under con-

tinual improvement and we reserve the right to make changes without notice�

Trademarks

All trademarks are the properties of their respective owners�

MSI is a registered trademark of Micro-Star Int’l Co�, Ltd�

Intel is a registered trademark of Intel Corporation�

Realtek is a registered trademark of Realtek Semiconductor Corporation�

Windows is a registered trademark of Microsoft Corporation�

Revision

Revision Date

V1�0 2012/10

￭

Preface

iv v

Wind Top Series

Preface

iv v

Wind Top Series

Upgrade and Warranty

Please note that certain components preinstalled in the product may be upgrad-

able or replaceable by user’s request� To learn more about upgrade limitation,

please refer to the speci󰘰cations in the User’s Manual� For any further information

about the product users purchased, please contact the local dealer� Do not attempt

to upgrade or replace any component of the product if you are not an authorized

dealer or service center, since it may cause the warranty void� It is strongly recom-

mended that you contact the authorized dealer or service center for any upgrade

or replace service�

Acquisition of Replaceable Parts

Please be noticed that the acquisition of replaceable parts (or compatible ones) of

the product users purchased in certain countries or territories may be ful󰘰lled by

the manufacturer within 5 years at most since the product has been discontinued,

depending on the o󰘲cial regulations declared at the time�

Please contact the manufacturer via http://support�msi�com/ for the detailed infor-

mation about the acquisition of spare parts�

Technical Support

If a problem arises with your system and no solution can be obtained from the

user’s manual, please contact your place of purchase or local distributor� Alterna-

tively, please try the following help resources for further guidance�

Visit the MSI website for technical guide, BIOS updates, driver updates

and other information via http://www�msi�com/service/download/

Contact our technical sta󰘯 via http://support�msi�com/

Green Product Features

Reduced energy consumption during use and stand-by

Limited use of substances harmful to the environment and health

Easily dismantled and recycled

Reduced use of natural resources by encouraging recycling

Extended product lifetime through easy upgrades

Reduced solid waste production through take-back policy

◙

Preface

iv v

Wind Top Series

Preface

iv v

Wind Top Series

Environmental Policy

The product has been designed to enable proper reuse of

parts and recycling and should not be thrown away at its

end of life�

Users should contact the local authorized point of collection

for recycling and disposing of their end-of-life products�

Visit the MSI website and locate a nearby distributor for further recycling

information�

Users may also reach us at cso@msi�com for information regarding

proper Disposal, Take-back, Recycling, and Disassembly of MSI prod-

ucts�

Chemical Substances Information

In compliance with chemical substances regulations, such as the EU REACH

Regulation (Regulation EC No� 1907/2006 of the European Parliament and the

Council), MSI provides the information of chemical substances in products at:

http://www�msi�com/html/popup/csr/evmtprtt_pcm�html

Battery Information

European Union:

Batteries, battery packs, and accumulators should not be

disposed of as unsorted household waste� Please use the

public collection system to return, recycle, or treat them in

compliance with the local regulations�

Taiwan:

For better environmental protection, waste batteries should

be collected separately for recycling or special disposal�

California, USA:

The button cell battery may contain perchlorate material and requires special

handling when recycled or disposed of in California�

For further information please visit:

http://www�dtsc�ca�gov/hazardouswaste/perchlorate/

Danger of explosion if battery is incorrectly replaced� Replace only with the

same or equivalent type recommended by the manufacturer�

◙

Preface

vi vii

Wind Top Series

Preface

vi vii

Wind Top Series

Safety Instructions

Read the safety instructions carefully and thoroughly�

All cautions and warnings on the equipment or user’s manual should be

noted�

Keep the User’s Guide that comes with the package for future reference�

Keep this equipment away from humidity and high temperature�

Lay this equipment on a reliable 󰘱at surface before setting it up�

Make sure that the power voltage is within its safety range and has

been adjusted properly to the value of 100~240V before connecting

the equipment to the power outlet� Do not disable the protective earth

pin from the plug� The equipment must be connected to an earthed

mains socket-outlet�

Always unplug the AC power cord before installing any add-on card

or module to the equipment�

Always disconnect the AC power cord or switch the wall socket o󰘯 if

the equipment would be left unused for a certain time to achieve zero

energy consumption�

◙

The ventilator on the enclosure is used for air convection and to prevent

the equipment from overheating� Do not cover the ventilator�

Do not leave the equipment in an unconditioned environment with a stor-

age temperature above 60OC (140OF) or below 0OC (32OF), which may

damage the equipment�

NOTE: The maximum operating temperature is around 40OC�

Preface

vi vii

Wind Top Series

Preface

vi vii

Wind Top Series

Never pour any liquid into the opening that could damage or cause electri-

cal shock�

Place the power cord in a way that people are unlikely to step on it� Do not

place anything on the power cord�

When installing the coaxial cable to the TV Tuner, it is necessary to en-

sure that the metal shield is reliably connected to protective earthing sys-

tem of the building�

Cable distribution system should be grounded (earthed) in accordance

with ANSI/NFPA 70, the National Electrical Code (NEC), in particular Sec-

tion 820�93, Grounding of Outer Conductive Shield of a Coaxial Cable�

Always keep the strong magnetic or electrical objects away from the

equipment�

If any of the following situations arises, get the equipment checked by

service personnel:

The power cord or plug is damaged�

Liquid has penetrated into the equipment�

The equipment has been exposed to moisture�

The equipment does not work well or you can not get it work accord-

ing to user’s manual�

The equipment has dropped and damaged�

The equipment has obvious sign of breakage�

◙

The optical storage devices are classi󰘰ed as CLASS 1 LASER PRODUCT� Use of

controls or adjustments or performance of procedures other than those speci󰘰ed

is prohibited�

Do not touch the lens inside the drive�

1�

2�

Preface

viii ix

Wind Top Series

Preface

viii ix

Wind Top Series

CE Conformity

Hereby, Micro-Star International CO�, LTD declares that this de-

vice is in compliance with the essential safety requirements and

other relevant provisions set out in the European Directive�

FCC-B Radio Frequency Interference

Statement

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules� These limits are designed to provide reasonable

protection against harmful interference in a residential instal-

lation� This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications� However, there

is no guarantee that interference will not occur in a particular installation� If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment o󰘯 and on, the user is encouraged to

try to correct the interference by one or more of the measures listed below:

Reorient or relocate the receiving antenna�

Increase the separation between the equipment and receiver�

Connect the equipment into an outlet on a circuit di󰘯erent from that to

which the receiver is connected�

Consult the dealer or an experienced radio/television technician for

help�

Notice 1

The changes or modi󰘰cations not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment�

Notice 2

Shielded interface cables and AC power cord, if any, must be used in order to

comply with the emission limits�

VOIR LA NOTICE D’INSTALLATION AVANT DE RACCORDER AU RESEAU�

This device complies with Part 15 of the FCC Rules� Operation is subject to the

following two conditions:

this device may not cause harmful interference, and

this device must accept any interference received, including interference that

may cause undesired operation�

￭

1�

2�

Preface

viii ix

Wind Top Series

Preface

viii ix

Wind Top Series

WEEE Statement

(English) Under the European Union (“EU”) Directive on Waste Electrical and Electronic

Equipment, Directive 2002/96/EC, which takes e󰘯ect on August 13, 2005, products of

“electrical and electronic equipment” cannot be discarded as municipal waste anymore

and manufacturers of covered electronic equipment will be obligated to take back such

products at the end of their useful life�

(French) (Français) Au sujet de la directive européenne (EU) relative aux déchets des

équipement électriques et électroniques, directive 2002/96/EC, prenant e󰘯et le 13 août

2005, que les produits électriques et électroniques ne peuvent être déposés dans les

décharges ou tout simplement mis à la poubelle� Les fabricants de ces équipements se-

ront obligés de récupérer certains produits en 󰘰n de vie�

(German) (Deutsch) Gemäß der Europäischen Union (“EU”) Richtlinie über Elektro-und

Elektronik-Altgeräte (Richtlinie 2002/96/EG) mit Wirkung vom 13� August 2005, dürfen

Elektro- und Elektronikgeräten nicht mehr als Hausmüll entsorgt werden� Der Hersteller

verp󰘱ichtet sich zur Rücknahme solcher Produkte am Ende ihrer Nutzungsdauer�

(Spanish) (Español) Bajo la directiva 2002/96/EC de la Unión Europea en materia de

desechos y/o equipos electrónicos, con fecha de rigor desde el 13 de agosto de 2005,

los productos clasi󰘰cados como “eléctricos y equipos electrónicos” no pueden ser depos-

itados en los contenedores habituales de su municipio, los fabricantes de equipos elec-

trónicos, están obligados a hacerse cargo de dichos productos al termino de su período

de vida�

(Italian) (Italiano) In base alla Direttiva dell’Unione Europea (EU) sullo Smaltimento dei

Materiali Elettrici ed Elettronici, Direttiva 2002/96/EC in vigore dal 13 Agosto 2005, prodotti

appartenenti alla categoria dei Materiali Elettrici ed Elettronici non possono più essere

eliminati come ri󰘰uti municipali: i produttori di detti materiali saranno obbligati a ritirare ogni

prodotto alla 󰘰ne del suo ciclo di vita�

(Russian) (Русский) В соответствии с директивой Европейского Союза (ЕС) по

предотвращению загрязнения окружающей среды использованным электрическим

и электронным оборудованием (директива WEEE 2002/96/EC), вступающей в силу

13 августа 2005 года, изделия, относящиеся к электрическому и электронному

оборудованию, не могут рассматриваться как бытовой мусор, поэтому производители

вышеперечисленного электронного оборудования обязаны принимать его для

переработки по окончании срока службы�

(Turkish) (Türkçe) Avrupa Birliği (AB) Kararnamesi Elektrik ve Elektronik Malzeme Atığı,

2002/96/EC Kararnamesi altında 13 Ağustos 2005 tarihinden itibaren geçerli olmak üzere,

elektrikli ve elektronik malzemeler diğer atıklar gibi çöpe atılamayacak ve bu elektonik

cihazların üreticileri, cihazların kullanım süreleri bittikten sonra ürünleri geri toplamakla

yükümlü olacaktır�

Preface

x xi

Wind Top Series

Preface

x xi

Wind Top Series

(Greek) (Ελληνικά) Σύμφωνα με την Οδηγία 2002/96/ΕΚ της Ευρωπαϊκής Ένωσης («ΕΕ»)

περί Απόρριψης Ηλεκτρικού και Ηλεκτρονικού Εξοπλισμού (WEEE), η οποία λαμβάνει

ισχύ στις 13 Αυγούστου 2005, τα προϊόντα «ηλεκτρικού και ηλεκτρονικού εξοπλισμού»

δεν είναι δυνατόν να απορριφθούν πλέον ως κοινά απορρίμματα και οι κατασκευαστές

κεκαλυμμένου ηλεκτρονικού εξοπλισμού είναι υποχρεωμένοι να πάρουν πίσω αυτά τα

προϊόντα στο τέλος της ωφέλιμης ζωής τους�

(Polish) (Polski) Zgodnie z Dyrektywą Unii Europejskiej (“UE”) dotyczącą odpadów produk-

tów elektrycznych i elektronicznych (Dyrektywa 2002/96/EC), która wchodzi w życie 13

sierpnia 2005, tzw� “produkty oraz wyposażenie elektryczne i elektroniczne “ nie mogą być

traktowane jako śmieci komunalne, tak więc producenci tych produktów będą zobowiązani

do odbierania ich w momencie gdy produkt jest wycofywany z użycia�

(Hungarian) (Magyar) Az Európai Unió („EU”) 2005� augusztus 13-án hatályba lépő, az

elektromos és elektronikus berendezések hulladékairól szóló 2002/96/EK irányelve szerint

az elektromos és elektronikus berendezések többé nem kezelhetőek lakossági hulladék-

ként, és az ilyen elektronikus berendezések gyártói kötelessé válnak az ilyen termékek

visszavételére azok hasznos élettartama végén�

(Czech) (Čeština) Podle směrnice Evropské unie (“EU”) o likvidaci elektrických a elek-

tronických výrobků 2002/96/EC platné od 13� srpna 2005 je zakázáno likvidovat “elek-

trické a elektronické výrobky” v běžném komunálním odpadu a výrobci elektronických

výrobků, na které se tato směrnice vztahuje, budou povinni odebírat takové výrobky zpět

po skončení jejich životnosti�

(Traditional Chinese ) (繁體中文) 歐盟已制訂有關廢電機電子設備法令，亦即自2005年8月

13日生效的2002/96/EC，明文規定「電機電子設備產品」不可再以都市廢棄物處理，且所

有相關電子設備製造商，均須在產品使用壽命結束後進行回收。

(Simpli󰘰ed Chinese ) (简体中文) 欧盟已制订有关废电机电子设备法令，亦即自2005年8月

13日生效的2002/96/EC，明文规定「电机电子设备产品」不可再以都市废弃物处理，且所

有相关电子设备制造商，均须在产品使用寿命结束后进行回收。

(Japanese) (日本語) 2005年8月13日以降にEU加盟国を流通する電気・電子製品には

WEEE指令によりゴミ箱に×印のリサイクルマークの表示が義務づけられており、廃棄

物として捨てることの禁止とリサイクルが義務づけられています。

(Korean) (한국어) 2005년 8월 13일자로 시행된 폐전기전자제품에 대한 유럽연합(“EU”) 지

침, 지침 2002/96/EC에 의거하여, “전기전자제품”은 일반 쓰레기로 폐기할 수 없으며 제품

의 수명이 다하면 해당 전자제품의 제조업체가 이러한 제품을 회수할 책임이 있습니다�

(Vietnam) (Tieng Viet) Theo Hướng dẫn của Liên minh Châu Âu (“EU”) về Thiết bị điện &

điện tử đã qua sử dụng, Hướng dẫn 2002/96/EC, vốn đã có hiệu lực vào ngày 13/8/2005,

các sản phẩm thuộc “thiết bị điện và điện tử” sẽ không còn được vứt bỏ như là rác thải đô

thị nữa và các nhà sản xuất thiết bị điện tử tuân thủ hướng dẫn sẽ phải thu hồi các sản

phẩm này vào cuối vòng đời�

(Thai) (ไทย) ภายใต้ข้อกำหนดของสหภาพยุโรป (“EU”) เกี่ยวกับของเสียจากอุปกรณ์ไฟฟ้า

และอิเล็กทรอนิกส์ เลขที่ 2002/96/EC ซึ่งมีผลบังคับใช้ตั้งแต่วันที่ 13 สิงหาคม 2005 ผู้ใช้ไม่สามา

รถทิ้งผลิตภัณฑ์ที่เป็น “อุปกรณ์ไฟฟ้าและอิเล็กทรอนิกส์” ปะปนกับของเสียทั่วไปของชุมชนได้อีกต่อ

ไป และผู้ผลิตอุปกรณ์อิเล็กทรอนิกส์ดังกล่าวจะถูกบังคับให้นำผลิตภัณฑ์ดังกล่าวกลับคืนเมื่อ

สิ้นสุดอายุการใช้งานของผลิตภัณฑ์

Preface

x xi

Wind Top Series

Preface

x xi

Wind Top Series

(Indonesia) (Bahasa Indonesia) Sesuai dengan Regulasi Uni Eropa (“UE”) perihal WEEE

(Limbah Peralatan Listrik dan Elektronik), Directive 2002/96/EC, yang berlaku sejak 13,

2005, produk “peralatan listrik dan elektronik” tidak lagi dapat dibuang sebagai sampah

umum dan pabrik peralatan elektronik diwajibkan untuk mengambil kembali produk terse-

but pada saat masa pakainya habis�

(Serbian) (Srpski) Po Direktivi Evropske unije (“EU”) o odbačenoj ekektronskoj i električnoj

opremi, Direktiva 2002/96/EC, koja stupa na snagu od 13� Avgusta 2005, proizvodi koji

spadaju pod “elektronsku i električnu opremu” ne mogu više biti odbačeni kao običan ot-

pad i proizvođači ove opreme biće prinuđeni da uzmu natrag ove proizvode na kraju njiho-

vog uobičajenog veka trajanja�

(Netherlands) (Nederlands) De richtlijn van de Europese Unie (EU) met betrekking tot

Vervuiling van Electrische en Electronische producten (2002/96/EC), die op 13 Augustus

2005 in zal gaan kunnen niet meer beschouwd worden als vervuiling� Fabrikanten van

dit soort producten worden verplicht om producten retour te nemen aan het eind van hun

levenscyclus�

(Romanian) (Română) În baza Directivei Uniunii Europene (“UE”) privind Evacuarea Echi-

pamentului Electric şi Electronic, Directiva 2002/96/EC, care intră în vigoare pe 13 au-

gust, 2005, produsele din categoria “echipament electric şi electronic” nu mai pot 󰘰 evacu-

ate ca deşeuri municipale, iar fabricanţii echipamentului electronic vizat vor 󰘰 obligaţi să

primească înapoi produsele respective la sfârşitul duratei lor de utilizare�

(Portuguese) (Português) De acordo com a Directiva 2002/96/EC de Resíduos de Eq-

uipamentos Eléctricos e Electrónicos da União Europeia (UE), efectiva desde o 13 de

Agosto do ano 2005, os produtos de “equipamento eléctrico e electrónico” não podem ser

descartados como resíduo municipal e os fabricantes do equipamento electrónico sujeitos

a esta legislação estarão obligados a recolhar estes produtos ao 󰘰nalizar sua vida útil�

(Swedish) (Svenska) Under Europeiska unionens (“EU”) Weee-direktiv (Waste Electrical

and Electronic Equipment), Direktiv 2002/96/EC, vilket trädde i kraft 13 augusti, 2005, kan

inte produkter från “elektriska och elektroniska utrustningar” kastas i den vanliga hush-

ållssoporna längre och tillverkare av inbyggd elektronisk utrustning kommer att tvingas att

ta tillbaka sådan produkter när de är förbrukade�

(Finnish) (Suomi) Euroopan unionin (EU) 13�8�2005 voimaan tulleen sähkö- ja elektroniik-

kalaiteromua koskevan direktiivin 2002/96/EY mukaisesti ”sähkö- ja elektroniikkalaitteita”

ei saa enää hävittää talousjätteiden mukana� Direktiivin alaisen sähkö- tai elektroniikkalait-

teen valmistajan on otettava laitteet takaisin niiden käyttöiän päättyessä�

(Slovak) (Slovenčina) Na základe smernice Európskej únie („EU“) o elektrických a elek-

tronických zariadeniach číslo 2002/96/ES, ktorá vstúpila do platnosti 13� augusta 2005,

výrobky, ktorými sú „elektrické a elektronické zariadenia” nesmú byť zneškodňované spolu

s komunálnym odpadom a výrobcovia patričných elektronických zariadení sú povinní také-

to výrobky na konci životnosti prevziať naspäť�

(Slovenian) (Slovenščina) Skladno z določili direktive Evropske unije (“EU”) o odpadni

električni in elektronski opremi, Direktiva 2002/96/ES, ki je veljavna od 13� avgusta, izdel-

kov “električne in elektronske opreme” ni dovoljeno odstranjevati kot običajne komunalne

odpadke, proizvajalci zadevne elektronske opreme pa so zavezani, da tovrstne izdelke na

koncu njihove življenjske dobe sprejmejo nazaj�

Preface

xii PB

Wind Top Series

(Danish) (Dansk) I henhold til direktiv fra den europæiske union (EU) vedrørende elektrisk

og elektronisk a󰘯ald , Direktiv 2002/96/EC, som træder i kraft den 13� august 2005, må

produkter som “elektrisk og elektronisk udstyr” ikke mere bortska󰘯es som kommunalt af-

fald� Producenter af det pågældende, elektroniske udstyr vil være forpligtet til at tage disse

produkter tilbage ved afslutningen på produkternes levetid�

(Norwegian) (Norsk) Under den europeiske unionens (“EU”) direktiv om deponering av

elektronisk og elektrisk utstyr, direktiv 2002/96/EC, som trer i e󰘯ekt 13� august 2005, kan

ikke produkter av “elektronisk og elektrisk ustyr” lenger deponeres som husholdningsavfall

og fabrikantene av disse produktene er forpliktet å ta tilbake slike produkter ved slutten av

produktets levetid�

(Bulgarian) (български) Според директивата на Европейския съюз относно отпадъците

от електрическо и електронно оборудване, директива 2002/96/EC, важаща от 13

август, 2005 г�, електрическо и електронно оборудване не може да се изхвърля

заедно с битовите отпадъци и производителите на такова оборудване са задължени

да приемат обратно съответните продукти в края на експлоатационния им период�

(Croatian) (Hrvatski) U okviru Direktive Europske Unije (“EU”) o Otpadnim električnim i

elektroničkim uređajima, Direktiva 2002/96/EC, koja je na snazi od 13� kolovoza 2005�,

“električni i elektronički uređaji” se ne smiju više bacati zajedno s kućnim otpadom i

proizvođači su obvezni zbrinuti takve proizvode na kraju njihovog životnog vijeka�

(Estonia) (Eesti) Vastavalt Euroopa Liidu (“EL”) direktiivile 2002/96/EÜ (elektri- ja elek-

troonikaseadmete jäätmete kohta), mis jõustus 13� augustil 2005, on keelatud kodumaja-

pidamiste “elektri- ja elektroonikaseadmete” jäätmete hävitamine koos majapidamisjäät-

metega, ja elektri- ja elektroonikaseadmete tootjad on kohustatud sellised tooted pärast

nende kasutuselt kõrvaldamist tagasi võtma�

Chapter 1

Overview

This system is designed with green commerce and smart

digital lifestyle, using an LED backlit display to increase

clarity, while reducing the burden to the eyes� With the

compact chassis and 󰘱exible stand, it blends technology

with life, making computers easier to use - suitable for

both individuals and businesses�

Overview

1-2 1-3

Wind Top Series

Overview

1-2 1-3

Wind Top Series

Packing Contents

Wind Top Series AC/DC Adapter AC Power Cord

LCD Display Wiper

Driver/Utility Disk

User Manual &

Quick Guide

Keyboard (Optional)

Mouse (Optional)

Stylus (Optional)

* Please contact us immediately if any of the items is damaged or missing�

* The illustrations are for reference only and your packing contents may slightly vary

depending on the model you purchased�

Overview

1-2 1-3

Wind Top Series

Overview

1-2 1-3

Wind Top Series

System Overview

Front View

12

3

4



1Microphone

The built-in microphone can be used for video chatting online�

2Webcam

The built-in webcam with the microphone can be used for picture taking, video

recoding, online conferencing and any other interactive applications�

3Display

The 15�6-inch LED-backlit display is with an optimal resolution of 1366 x 768

pixels and standard proportion of 16:9 widescreen�

4Stereo Speakers

The built-in stereo speakers deliver high quality sound blaster with stereo sys-

tem�

Overview

1-4 1-5

Wind Top Series

Overview

1-4 1-5

Wind Top Series

Rear View

1

2

3

4



1Ventilator

The ventilator on the enclosure is used for air convection and to prevent the

equipment from overheating� Do not cover the ventilator�

2Stand

Use this stand to position your system on a 󰘱at and stable surface�

3Cable Routing Hole

Route the cables through the cable routing hole to avoid cable spaghetti when

connecting devices�

4Kensington Lock Port

This AIO PC provides a Kensington lock port, which allows users to secure

the AIO PC in place with a key or some mechanical PIN device and attached

through a rubberised metal cable� The end of the cable has a small loop which

allows the whole cable to be looped around a permanent object, such as a

heavy table or other similar equipment, thus securing the AIO PC in place�

Overview

1-4 1-5

Wind Top Series

Overview

1-4 1-5

Wind Top Series

Top & Bottom View

1

24

6 85 73

LAN2 LAN1



1Ventilator

The ventilator on the enclosure is used for air convection and to prevent the

equipment from overheating� Do not cover the ventilator�

2Line-Out Jack

This connector is provided for headphones or speakers�

3Microphone Jack

This connector is provided for microphones�

4USB 2�0 Port

The USB (Universal Serial Bus) port is for attaching USB devices such as key-

board, mouse, or other USB-compatible devices� It supports up to 480Mbit/s

(Hi-Speed) data transfer rate�

Overview

1-6 1-7

Wind Top Series

Overview

1-6 1-7

Wind Top Series

5RJ-45 LAN Jack (LAN2 Optional)

The standard RJ-45 LAN jack is provided for connection to the Local Area

Network (LAN)� You can connect a network cable to it�

YellowGreen/ Orange

LED Color LED State Condition

Right Yellow O󰘯 LAN link is not established�

On (steady state) LAN link is established�

On (brighter & pulsing) The computer is communicating with

another computer on the LAN�

Left Green O󰘯 10 Mbit/sec data rate is selected�

On 100 Mbit/sec data rate is selected�

Orange On 1000 Mbit/sec data rate is selected�

6VGA Port

The VGA port supports monitors and other VGA interface devices�

7Serial Port (Optional)

The serial port supports barcode scanners, barcode printers, bill printers, credit

card machine, etc�

8Parallel Port (Optional)

The parallel port supports printers and other parallel interface devices�

Overview

1-6 1-7

Wind Top Series

Overview

1-6 1-7

Wind Top Series

Side View

1System Power Button

Press the system power button to turn the system on or o󰘯�

2System Power LED

The power LED glows when the system is turned on and goes o󰘯 when the

system is shut down� In terms of power saving, the LED blinks in S3 (Suspend

to RAM) mode and goes o󰘯 in S4 (Suspend to Disk) mode�

3Hard Disk Drive LED

This indicator shows the activity status of the HDD� It 󰘱ashes when the sys-

tem is accessing data on the HDD and remains o󰘯 when no disk activity is

detected�

4Brightness Button

These buttons adjust the brightness level�

5Memory Card Reader

The built-in card reader may support various types of memory cards�

9

11

10

1

3

7

2

5

6

48

Optional

Overview

1-8 1-9

Wind Top Series

Overview

1-8 1-9

Wind Top Series

6USB 2�0 Port (Optional)

The USB (Universal Serial Bus) port is for attaching USB devices such as key-

board, mouse, or other USB-compatible devices� It supports up to 480Mbit/s

(Hi-Speed) data transfer rate�

USB 3�0 Port (Optional)

The USB 3�0 port is backward-compatible with USB 2�0 devices� It supports up

to 5Gbit/s (SuperSpeed) data transfer rate�

7Power Jack

The AC/DC adapter converts AC power to DC power for this jack� Power sup-

plied through this jack supplies power to the PC� To prevent damage to the PC,

always use the supplied power adapter�

8Smart Card Reader (Optional)

This card reader supports smart cards to provide identi󰘰cation, authentication,

data storage, application processing, etc�

9Optical Disk Drive (Optional)

A DVD Super-Multi drive is integrated for your home entertainment�

10 Eject Hole (Optional)

Insert a thin, straight object (such as a paper clip) into the eject hole to open the

optical disk drive manually if the eject button does not work�

11 Eject Button (Optional)

Press the eject button to open the optical disk drive�

Overview

1-8 1-9

Wind Top Series

Overview

1-8 1-9

Wind Top Series

System Specications

Processor

Intel® Celeron® Processor ■

Chipset

Intel® NM70 chipset■

Memory

1 DDR3 1333 MHz SO-DIMM slot

Supports the maximum of 4GB

■

LAN

Wired LAN: supported by Realtek® RTL8111E Gigabit Ethernet controller

Wireless LAN: optionally supported through Mini PCI-E WLAN module

■

Audio

HDA Codec by Realtek® ALC887

Compliant with Azalia 1�0 specs

■

Display

15�6-inch display with LED backlight

An optimal resolution of 1366 x 768 pixels

Standard proportion of 16:9 widescreen

■-

-

Bottom Input/ Output

1 Line-Out audio jack

1 microphone jack

2 USB 2�0 ports

2 RJ-45 LAN jacks (LAN2 Optional)

1 VGA port

2 serial ports (Optional)

1 parallel port (Optional)

■

Side Input/ Output

1 memory card reader

2 USB 2�0/ 3�0 ports (Optional)

1 DC power jack

1 smart card reader (Optional)

■

Overview

1-10 1-11

Wind Top Series

Overview

1-10 1-11

Wind Top Series

Storage

Hard Disk Drive: 2�5”, SATAII

Optical Disk Drive: Slim DVD Super Multi (Optional)

Card Reader:

SD/ MMC/ MS card reader

Smart card reader (Optional)

■

■-

-

Stereo Speaker

2 stereo speakers■

WebCam

Support webcam with microphone■

Power Supply

65 Watt AC/ DC adapter with active PFC

Input: 100-240V, 1�5A, 50-60Hz

Output: 19V 3�42A

■-

-

Overview

1-10 1-11

Wind Top Series

Overview

1-10 1-11

Wind Top Series

Component Replacement &

Upgrade

Please note that certain components preinstalled in the product may be up-

gradable or replaceable by user’s request depending on the models users pur-

chased�

To learn more about upgrade limitation, please refer to the speci󰘰cations in the

User’s Manual� For any further information on the product users purchased,

please contact the local dealer�

Do not attempt to upgrade or replace any component of the product if you are not

an authorized dealer or service center, since it may cause the warranty void� It is

strongly recommended that you contact the authorized dealer or service center

for any upgrade or replace service�

Chapter 2

Getting Started

This chapter provides you with the information on hard-

ware setup procedures� While connecting peripheral

devices, be careful in holding the devices and use a

grounded wrist strap to avoid static electricity�

Getting Started

2-2 2-3

Wind Top Series

Getting Started

2-2 2-3

Wind Top Series

Safety & Comfort Tips

The AIO PC is a portable platform that allows you to work anywhere� However,

choosing a good workspace is important if you have to work with your PC for a

long period of time�

Your work area should have enough illumination�

Choose the proper desk and chair and adjust their height to 󰘰t your posture

when operating�

When sitting on the chair, sit straight and keep a good posture� Adjust the

chair’s back (if available) to support your back comfortably�

Place you feet 󰘱at and naturally on the 󰘱oor, so that your knees and elbows

have the proper position (about 90-degree) when operating�

Put your hands on the desk naturally to support your wrists�

Adjust the angle/position of the AIO PC to have an optimal view�

Avoid using your PC in a place where discomfort may occur (such as on the

bed)�

The AIO PC is an electrical device� Please treat it with great care to avoid

personal injury�

1

38-76 cm

15- 2 0

90- 1 20

2

3

4

5

6

1�

2�

3�

4�

5�

6�

7�

8�

Getting Started

2-2 2-3

Wind Top Series

Getting Started

2-2 2-3

Wind Top Series

Hardware Setup

Positioning Your System

1� Place your system on a 󰘱at and steady surface such as a table or desk�

2� Tilt the display and pull the stand outwards to your desired extent� Make sure

the system is securely positioned before powering it on�



Getting Started

2-4 2-5

Wind Top Series

Getting Started

2-4 2-5

Wind Top Series

Connecting the AC Power

1� Assemble the AC/DC adapter and the AC power cord�

2� Plug the DC end of the adapter to the AIO PC�

3� Plug the male end of the AC power cord to the electrical outlet�

Important

We suggest that you connect the AC/DC adapter to your AIO PC 󰘰rst and then

connect the AC power cord to the socket-outlet for safety concerns�

3

2

1



Getting Started

2-4 2-5

Wind Top Series

Getting Started

2-4 2-5

Wind Top Series

Powering on the System

Press the power button to power on the system�



Chapter 3

System Operations

This chapter provides you with essential information on

system operations�

Important

All information is subject to change without prior notice�

System Operations

3-2 3-3

Wind Top Series

System Operations

3-2 3-3

Wind Top Series

System Booting Setup for the rst

time

For the 󰘰rst-time use, you will need to go over the following steps to start using

your Wind Top Series AIO PC� The entire booting setup will take you around 30

minutes�

1� Windows setup starts running� Please wait until Windows setup 󰘰nishes the

progress loading�

2� Select the language of the operating system and click [Next] to continue�

3� Choose the “Country or region”, “Time and currency”, and “Keyboard layout”

you need� Click [Next] to continue�

4� Choose a user name for your account and name your computer to distin-

guish it on the network� Click [Next] to continue�

5� Set a password for your account to protect your user account from unwanted

users� (Leave this 󰘰eld blank if no need for password�) Click [Next] to con-

tinue�

6� Please read the license terms� Check the “I accept the license terms” box

and click [Next] to continue�

7� Select [Use recommended settings] for “Help protect your computer and

improve Windows automatically�”

8� Review your time and date settings� Click [Next] to continue�

9� Please choose a wireless network you intend to join from the provided

WLAN list� Click [Next] to continue� You may also click [Skip] to skip this step

and set up the WLAN later�

10� (Optional) Followingly comes the anti-virus software screen� Click [Agree]

to accept the license agreement terms and activate the anti-virus software�

Alternatively, choose [Stay Unprotected] and click [Next] to proceed without

activating the anti-virus software�

11� The “Software Installation Menu” pops up� Click [Install] to continue�

12� The software is being installed� Please do not turn o󰘯 the computer when

software installation is running� When the progress bar completes loading,

click [Finish] to continue�

13� The system enters the Windows 7 OS to start its personalized settings� Get

ready to explore your AIO PC after the personalized settings are done�

Have fun with it!

System Operations

3-2 3-3

Wind Top Series

System Operations

3-2 3-3

Wind Top Series

Touch Panel Calibration (Only for

single-touch model)

Wind Top Series AIO PC has touch panel function� If the mouse cursor can not

match the move, users could use the calibration tool installed in the system to

adjust the accuracy of the touch panel� Please go over the following steps to get

it done�

1� Locate the calibration tool at [Start] > [All Programs]�

2� Three calibration modes are provided: 4 points, 9 points, and 25 points� We

suggest that users choose 9 points to adjust the touch panel� If users desire

the best precision, then choose 25 points instead�

System Operations

3-4 3-5

Wind Top Series

System Operations

3-4 3-5

Wind Top Series

3� Follow the on-screen instructions to calibrate the touch panel�

Important

Do not touch the screen directly with any sharp-pointed object�

Actual product speci󰘰cations may vary with territories�

•

System Operations

3-4 3-5

Wind Top Series

System Operations

3-4 3-5

Wind Top Series

Network Connection under

Windows

Wired LAN

1� Go to [Start] > [Control Panel]�

2� Select [Connect to the Internet] under [Network and Internet]�



System Operations

3-6 3-7

Wind Top Series

System Operations

3-6 3-7

Wind Top Series

3� Select [Broadband (PPPoE)] to connect using DSL or cable that requires a

user name and password�

4� Type the information from your Internet Service Provider (ISP) and click

[Connect] to establish your LAN connection�

System Operations

3-6 3-7

Wind Top Series

System Operations

3-6 3-7

Wind Top Series

Wireless LAN

1� Go to [Start] > [Control Panel]�

2� Select [Connect to the Internet] under [Network and Internet]�



System Operations

3-8 3-9

Wind Top Series

System Operations

3-8 3-9

Wind Top Series

3� Select [Wireless] to connect using a wireless router or a wireless network�

4� A list of available WLAN connections pops up� Choose a connection from the

list or click [Open Network and Sharing Center] to establish a new connec-

tion�

5� To establish a new WLAN connection, select [Set up a new connection or

network] in [Network and Sharing Center]�

System Operations

3-8 3-9

Wind Top Series

System Operations

3-8 3-9

Wind Top Series

6� Followingly, choose [Manually connect to a wireless network] and click [Next]

to continue�

7� Enter information for the wireless network you intend to add and click [Next]

to proceed�

8� A new WLAN connection has been made� Click [Close] to exit or select

[Change connection settings] to modify the WLAN settings�

System Operations

3-10 3-11

Wind Top Series

System Operations

3-10 3-11

Wind Top Series

Power Management

Power management of personal computers (PCs) and monitors has the poten-

tial to save signi󰘰cant amounts of electricity as well as deliver environmental

bene󰘰ts�

To be energy e󰘲cient, turn o󰘯 your display or set your PC to sleep mode after a

period of user inactivity�

Power Management in Windows OS

[Power Options] in Windows OS allow you to control the power manage-

ment features of your display, hard drive, and battery� Go to [Start] >

[Control Panel] > [System and Security]�

Then click on the [Power Options] link�

Select a power plan that suits your personal needs� You may also 󰘰ne-

tune the settings by clicking [Change plan settings]�



■

System Operations

3-10 3-11

Wind Top Series

System Operations

3-10 3-11

Wind Top Series

The Shut Down Computer menu presents the options of Sleep (S3/S4) &

Shut Down (S5) for rapid and easy management of your system power�

Power Management through ENERGY STAR

qualied monitors (Optional)

The power management feature allows the computer to initiate a low-power or

“Sleep” mode after a period of user inactivity� When used with an external ENER-

GY STAR quali󰘰ed monitor, this feature also supports similar power management

features of the monitor� To take advantage of these potential energy savings,

the power management feature has been preset to behave in the following ways

when the system is operating on AC power:

Turn o󰘯 the display after 15 minutes

Initiate Sleep after 30 minutes

Waking the System Up

The computer shall be able to wake up from power saving mode in response to a

command from any of the following:

the power button,

the network (Wake On LAN),

the mouse,

the keyboard�

Energy Saving Tips:

Turn o󰘯 the monitor by pressing the LCD power button after a period of

user inactivity�

Tune the settings in Power Options under Windows OS to optimize your

PC’s power management�

Install power saving software to manage your PC’s energy consumption�

Always disconnect the AC power cord or switch the wall socket o󰘯 if

your PC would be left unused for a certain time to achieve zero energy

consumption�

■



■



■

System Operations

3-12 3-13

Wind Top Series

System Operations

3-12 3-13

Wind Top Series

System Recovery Tool

Important

The Recovery Tool is only available on systems bundled with Windows OS and

MSI utilities by default�

The purposes for using the Recovery Tool may include:

Restore the system back to the initial status of original manufacturer’s

default settings�

When some errors have occurred to the operating system in use�

When the operating system is a󰘯ected by virus and is not able to work

normally�

When you want to install the OS with other built-in languages�

Before using the Recovery Tool, please back up the important data saved on your

system drive to other storage devices�

If the following solution fails to recover your system, please contact the authorized

local distributor or service center for further assistance�

Recovering the System with the F3 Hotkey

If the system encounters non-recoverable problems, it is always recommended

that you try the F3 hotkey to recover your system with the recovery partition of the

hard disk drive 󰘰rst�

Follow the instructions below to continue:

1� Restart the system�

2� Press the F3 hotkey on the keyboard when the following image appears�

■



System Operations

3-12 3-13

Wind Top Series

System Operations

3-12 3-13

Wind Top Series

3� Enter the Recovery Tool� This tool contains three features: Backup System,

Restore System and Recover to factory default�

System Backup

It is highly recommended that users back up the system as the solution in the

event of a catastrophic disk failure or other accidents�

Follow the instructions below to continue:

1� Select [Backup System] to enter� Alternatively, select [X] or press [Esc] on the

keyboard to exit�



System Operations

3-14 3-15

Wind Top Series

System Operations

3-14 3-15

Wind Top Series

2� Select [BACKUP] to start the system backup immediately�

The Initial Backup

The initial backup may take a while� Please let it complete without interruption�

Subsequent Backups

Subsequent backups will replace the previous backup 󰘰les�



System Operations

3-14 3-15

Wind Top Series

System Operations

3-14 3-15

Wind Top Series

3� The system backup is in progress� Please note that it may take a while� Do not

switch o󰘯 the power, or it may cause unknown damage to the system�

4� Alternatively, select [CANCEL] to stop the system backup immediately� Please

do not switch o󰘯 the power while the system backup cancellation is in prog-

ress�

System Operations

3-16 3-17

Wind Top Series

System Operations

3-16 3-17

Wind Top Series

5� The following message indicates a successful system backup� Press [OK] to

󰘰nish�

System Restore

This tool helps to return the system to a previous state with the backup 󰘰les that

users created and saved in the hard disk drive beforehand� If no backup 󰘰les are

available, the system will be restored to the default setup�

Follow the instructions below to continue:

1� Select [Restore System] to enter� Alternatively, select [X] or press [Esc] on the

keyboard to exit�



System Operations

3-16 3-17

Wind Top Series

System Operations

3-16 3-17

Wind Top Series

2� Select [OK] or [NEXT] so that the system can recover to the previous backup

or default setup� Alternatively, select [CANCEL] to stop the system restore

immediately�

With backup les: restoring the system to the previous back-

up

Without backup les: restoring the system to the default

setup



System Operations

3-18 3-19

Wind Top Series

System Operations

3-18 3-19

Wind Top Series

3� The system restore is in progress� Please note that it may take a while� Do not

switch o󰘯 the power, or it may cause unknown damage to the system�

4� The following message indicates a successful system restore� Press [OK] to

󰘰nish� Restart the system and access the Windows operating system as usual�

If the restore process fails or is interrupted, please start the whole procedure

all over again�

System Operations

3-18 3-19

Wind Top Series

System Operations

3-18 3-19

Wind Top Series

System Recovery

This tool helps to recover the system back to factory default settings� All data on

the HDD will be erased while all settings will be restored to factory default�

Follow the instructions below to continue:

1� Select [Recover to factory default] to enter� Alternatively, select [X] or press

[Esc] on the keyboard to exit�

2� The system will be recovered to factory settings� All data will be gone� Make

sure all important data have been backed up� Select [NEXT] to continue� Alter-

natively, select [CANCEL] to stop�



System Operations

3-20 3-21

Wind Top Series

System Operations

3-20 3-21

Wind Top Series

3� Please select [OK] so that the system can recover its default setup�

4� The system recovery is in progress� Please note that it may take a while� Do not

switch o󰘯 the power, or it may cause unknown damage to the system�

System Operations

3-20 3-21

Wind Top Series

System Operations

3-20 3-21

Wind Top Series

5� The following message indicates a successful system recovery� Press [OK]

to 󰘰nish� Restart the system and access the Windows operating system as

usual� If the recovery process fails or is interrupted, please start the whole

procedure all over again�

Appendix A

Troubleshooting

A-2

My system does not start�

1� Check if the system is connected to an electrical outlet and it is turned on�

2� Check if the power cord and all cables are connected 󰘰rmly�

When I turn on my computer, the message “Operating System not found”

appears or Windows does not start�

1� Check if there is a non-bootable CD/ DVD inside the optical disk drive� If so, re-

move the CD/ DVD then restart the computer�

2� Check Boot Device Priority settings in the BIOS Setup�

The system can not be shut down�

It is best to shut down your computer using the Shut Down icon in the operating sys-

tem� Using other methods, including those listed below, may result in data failure� If

the Shut Down procedure does not work, choose one of the following steps:

1� Press Ctrl+Alt+Del keys, then choose Shut Down�

2� Press and hold the power button till the system is o󰘯�

3� Unplug the power cable from the system�

My microphone does not work�

1� For built-in microphone, please go to Start > Control Panel > Sounds and Audio

Devices > Audio to check if it is muted�

2� If you are using an external microphone, check that the microphone is plugged

into the Microphone jack�

The Internet connection has problems�

1� If you are having a problem connecting to your Internet Service Provider (ISP),

check if the ISP is experiencing technical problems�

2� Check the Network settings and connection and make sure the system is properly

con󰘰gured to Internet access�

3� The wireless LAN data transfer speed is a󰘯ected by distance and obstructions be-

tween devices and access points� To maximize the data transfer speed, choose

the access point closest to your system�

A-3

Wind Top Series

System speakers do not work�

1� Check the master volume setting in the Audio Mixer�

2� If you are using an application that has its own volume control, check if the volume

is muted�

3� If you have connected an audio cable to the Headphone jack, disconnect it�

4� If the system has OSD function, please adjust the volume of OSD�

I cannot play a CD/ DVD with the DVD-ROM of the system�

1� Make sure the label of the CD/ DVD is facing up�

2� If the CD/ DVD requires software, make sure the software is well installed accord-

ing to the program instructions�

3� If a region code warning appears when you play the DVD, the problem could be

that the DVD is incompatible with the DVD-ROM in your system� The region code

is listed on the disc packaging�

4� If you see video but cannot hear audio, check the media player� Also, make sure

the speakers and the master volume setting in the Audio Mixer are not muted�

5� Check if the drivers are installed properly� Click Start > Control Panel > System >

Device Manager�

6� A dirty or scratched disc may cause the computer to hang when it is trying to read

the disc� If necessary, reboot the computer, remove the disc, and check if it is

dirty or scratched�

7� Please use DVD player software like PowerDVD or WinDVD to play DVD video�

My DVD-ROM drive tray does not open�

1� Make sure the computer is turned on�

2� Press the Eject button on the DVD-ROM drive�

3� If the Eject button does not work, open the tray by inserting a sharp, pointed object

into the hole next to the Eject button�

System monitor does not display anything�

1� Check if the system is connected to an electrical outlet and it is turned on�

2� The system may be in Standby mode� Press any key to activate the Display�

Table of Contents

MSI AP1622ET-B10374G50XXASXH User Manual

Related Manuals

MSI MSI WS76 11UM-440 Manual

MSI MPG Z590 GAMING PLUS Manual

MSI MPG Z590 GAMING EDGE WIFI Manual

MSI MPG Z590 GAMING EDGE WIFI Manual

MSI MPG Z590 GAMING FORCE Manual

MSI B560M PRO-VDH WIFI Manual

MSI B560M PRO-VDH WIFI Manual

MSI GF63 9SCSR-1411UK Thin Manual