Quick Start
- Preparing Tools and Components
- Safety Information
- Installing a Processor
- Installing DDR4 memory
- Connecting the Front Panel Header
- Installing the Motherboard
- Connecting the Power Connectors
- Installing SATA Drives
- Installing a Graphics Card
- Connecting Peripheral Devices
- Power On
Specifications
Package contents
Block Diagram
Rear I/O Panel
- LAN Port LED Status Table
- Audio Ports Configuration
- Realtek Audio Console
Overview of Components
- CPU Socket
- DIMM Slots
- PCI_E1~4: PCIe Expansion Slots
- M2_1~2: M.2 Slots (Key M)
- SATA1~6: SATA 6Gb/s Connectors
- JFP1, JFP2: Front Panel Connectors
- CPU_PWR1~2, ATX_PWR1: Power Connectors
- CPU_FAN1, PUMP_FAN1, SYS_FAN1~4: Fan Connectors
- JUSB1~2: USB 2.0 Connectors
- JUSB3~4: USB 3.2 Gen 1 5Gbps Connectors
- JUSB5: USB 3.2 Gen 2 10Gbps Type-C Connector
- JAUD1: Front Audio Connector
- JTBT1: Thunderbolt Add-on Card Connector
- JRTD3: Intel RTD3 Connector
- JCI1: Chassis Intrusion Connector
- JCOM1: Serial Port Connector
- JBAT1: Clear CMOS (Reset BIOS) Jumper
- EZ Debug LED
- JRGB1~2: RGB LED connectors
- JRAINBOW1~2: Addressable RGB LED connectors
Installing OS, Drivers & Utilities
- Installing Windows® 10
- Installing Drivers
- Installing Utilities
BIOS Setup
- Entering BIOS Setup
- Resetting BIOS
- Updating BIOS
- EZ Mode
- Advanced Mode
- SETTINGS
- Advanced
- Boot
- Security
- Save & Exit
- OC
- M-FLASH
- OC PROFILE
- HARDWARE MONITOR
AMD RAID Configuration
- Enabling RAIDXpert2 Configuration Utility
- Initializing Disks
- Creating Arrays
- Deleting Arrays
- Installing RAID Driver
Troubleshooting
CPU_FAN1, PUMP_FAN1, SYS_FAN1~4: Fan Connectors
CPU_PWR1~2, ATX_PWR1: Power Connectors
CPU Socket
DIMM Slots
JAUD1: Front Audio Connector
JBAT1: Clear CMOS (Reset BIOS) Jumper
JCI1: Chassis Intrusion Connector
JCOM1: Serial Port Connector
JFP1, JFP2: Front Panel Connectors
JRAINBOW1~2: Addressable RGB LED connectors
JRGB1~2: RGB LED connectors
JRTD3: Intel RTD3 Connector
JTBT1: Thunderbolt Add-on Card Connector
JUSB1~2: USB 2.0 Connectors
JUSB3~4: USB 3.2 Gen1 Connectors
JUSB5: USB 3.2 Gen 2 Type-C Connector
M2_1~2: M.2 Slots (Key M)
PCI_E1~4: PCIe Expansion Slots
SATA1~6: SATA 6Gb/s Connectors

MSI MAG X570 TOMAHAWK WIFI User Manual

Displayed below is the user manual for MAG X570 TOMAHAWK WIFI by MSI which is a product in the Motherboards category. This manual has pages.

Related Manuals

MSI MAG X570S TOMAHAWK MAX WIFI Manual

MSI MAG Z590 TOMAHAWK WIFI Manual

MSI MAG B560 TOMAHAWK WIFI Manual

MSI MAG Z690 TOMAHAWK WIFI DDR4 ATX Manual

MSI MAG Z690 TOMAHAWK WIFI Manual

MSI MAG H670 Tomahawk WIFI DDR4 Manual

MSI MAG B660 TOMAHAWK WIFI DDR4 Manual

Quick Start

Thank you for purchasing the MSI® MAG X570 TOMAHAWK WIFI motherboard. This

Quick Start section provides demonstration diagrams about how to install your

computer. Some of the installations also provide video demonstrations. Please link to

the URL to watch it with the web browser on your phone or tablet. You may have even

link to the URL by scanning the QR code.

Preparing Tools and Components

DDR4 Memory

Graphics Card

SATA Hard Disk Drive SATA DVD Drive

Phillips Screwdriver

Chassis

Power Supply Unit

A Package of Screws

Thermal Paste

CPU Fan

AMD® AM4 CPU

2Quick Start

Safety Information

∙The components included in this package are prone to damage from electrostatic

discharge (ESD). Please adhere to the following instructions to ensure successful

computer assembly.

∙Ensure that all components are securely connected. Loose connections may cause

the computer to not recognize a component or fail to start.

∙Hold the motherboard by the edges to avoid touching sensitive components.

∙It is recommended to wear an electrostatic discharge (ESD) wrist strap when

handling the motherboard to prevent electrostatic damage. If an ESD wrist strap is

not available, discharge yourself of static electricity by touching another metal object

before handling the motherboard.

∙Store the motherboard in an electrostatic shielding container or on an anti-static

pad whenever the motherboard is not installed.

∙Before turning on the computer, ensure that there are no loose screws or metal

components on the motherboard or anywhere within the computer case.

∙Do not boot the computer before installation is completed. This could cause

permanent damage to the components as well as injury to the user.

∙If you need help during any installation step, please consult a certified computer

technician.

∙Always turn off the power supply and unplug the power cord from the power outlet

before installing or removing any computer component.

∙Keep this user guide for future reference.

∙Keep this motherboard away from humidity.

∙Make sure that your electrical outlet provides the same voltage as is indicated on

the PSU, before connecting the PSU to the electrical outlet.

∙Place the power cord such a way that people can not step on it. Do not place

anything over the power cord.

∙All cautions and warnings on the motherboard should be noted.

∙If any of the following situations arises, get the motherboard checked by service

personnel:

▪Liquid has penetrated into the computer.

▪The motherboard has been exposed to moisture.

▪The motherboard does not work well or you can not get it work according to user

guide.

▪The motherboard has been dropped and damaged.

▪The motherboard has obvious sign of breakage.

∙Do not leave this motherboard in an environment above 60°C (140°F), it may damage

the motherboard.

Quick Start

Installing a Processor

https://youtu.be/Xv89nhFk1vc

4Quick Start

⚠

Important

If you are installing the screw-type CPU heatsink, please follow the figure below to

remove the retention module first and then install the heatsink.

Quick Start

Installing DDR4 memory

http://youtu.be/T03aDrJPyQs

DIMMA2 DIMMA2

DIMMB2

DIMMA1

DIMMA2

DIMMB1

DIMMB2

6Quick Start

HDD LED

RESET SW

Connecting the Front Panel Header

http://youtu.be/DPELIdVNZUI

JFP1

HDD LED HDD LED -

HDD LED +

POWER LED -

POWER LED +

POWER LED

2 10

+- --

Power LED

HDD LED Reset Switch

Reserved

Power Switch

JFP1

1 HDD LED + 2 Power LED +

3 HDD LED - 4 Power LED -

5 Reset Switch 6 Power Switch

7 Reset Switch 8 Power Switch

9 Reserved 10 No Pin

RESET SW

POWER SW

POWER LED+

POWER LED-

HDD LED

Quick Start

BAT1

Installing the Motherboard

Torque:

3 kgf·cm*

*3 kgf·cm

= 0.3 N·m

= 2.6 lbf·in

8Quick Start

Connecting the Power Connectors

http://youtu.be/gkDYyR_83I4

ATX_PWR1 CPU_PWR1

CPU_PWR2

Quick Start

Installing SATA Drives

http://youtu.be/RZsMpqxythc

10 Quick Start

Installing a Graphics Card

http://youtu.be/mG0GZpr9w_A

Quick Start

Connecting Peripheral Devices

Processor with integrated graphics

12 Quick Start

Power On

Contents

Quick Start ............................................................................................................. 1

Preparing Tools and Components .......................................................................... 1

Safety Information .................................................................................................. 2

Installing a Processor ............................................................................................. 3

Installing DDR4 memory ........................................................................................ 5

Connecting the Front Panel Header ....................................................................... 6

Installing the Motherboard ..................................................................................... 7

Connecting the Power Connectors ......................................................................... 8

Installing SATA Drives............................................................................................. 9

Installing a Graphics Card .................................................................................... 10

Connecting Peripheral Devices ............................................................................ 11

Power On............................................................................................................... 12

Specifications ....................................................................................................... 15

Package contents ................................................................................................ 21

Block Diagram .................................................................................................... 22

Rear I/O Panel ..................................................................................................... 23

LAN Port LED Status Table................................................................................... 23

Audio Ports Configuration .................................................................................... 23

Realtek Audio Console ......................................................................................... 24

Overview of Components .................................................................................... 27

CPU Socket ........................................................................................................... 29

DIMM Slots ............................................................................................................ 30

PCI_E1~4: PCIe Expansion Slots .......................................................................... 31

M2_1~2: M.2 Slots (Key M) ................................................................................... 32

SATA1~6: SATA 6Gb/s Connectors ....................................................................... 34

JFP1, JFP2: Front Panel Connectors ................................................................... 34

CPU_PWR1~2, ATX_PWR1: Power Connectors ................................................... 35

CPU_FAN1, PUMP_FAN1, SYS_FAN1~4: Fan Connectors ................................... 36

JUSB1~2: USB 2.0 Connectors ............................................................................. 37

JUSB3~4: USB 3.2 Gen 1 5Gbps Connectors ....................................................... 37

JUSB5: USB 3.2 Gen 2 10Gbps Type-C Connector ............................................... 38

JAUD1: Front Audio Connector ............................................................................ 38

JTBT1: Thunderbolt Add-on Card Connector ...................................................... 39

JRTD3: Intel RTD3 Connector .............................................................................. 39

JCI1: Chassis Intrusion Connector ....................................................................... 40

待更新

14 Contents

JCOM1: Serial Port Connector ............................................................................. 40

JBAT1: Clear CMOS (Reset BIOS) Jumper ........................................................... 41

EZ Debug LED ....................................................................................................... 41

JRGB1~2: RGB LED connectors ........................................................................... 42

JRAINBOW1~2: Addressable RGB LED connectors ............................................. 43

Installing OS, Drivers & Utilities ......................................................................... 44

Installing Windows® 10 ......................................................................................... 44

Installing Drivers .................................................................................................. 44

Installing Utilities ................................................................................................. 44

BIOS Setup ........................................................................................................... 45

Entering BIOS Setup ............................................................................................. 45

Resetting BIOS ...................................................................................................... 46

Updating BIOS ....................................................................................................... 46

EZ Mode ................................................................................................................ 48

Advanced Mode .................................................................................................... 50

SETTINGS .............................................................................................................. 51

Advanced ............................................................................................................... 51

Boot ....................................................................................................................... 56

Security ................................................................................................................. 57

Save & Exit ............................................................................................................ 58

OC .......................................................................................................................... 59

M-FLASH .............................................................................................................. 63

OC PROFILE .......................................................................................................... 64

HARDWARE MONITOR .......................................................................................... 65

AMD RAID Configuration ..................................................................................... 66

Enabling RAIDXpert2 Configuration Utility .......................................................... 66

Initializing Disks ................................................................................................... 67

Creating Arrays ..................................................................................................... 68

Deleting Arrays ..................................................................................................... 69

Installing RAID Driver ........................................................................................... 70

Troubleshooting .................................................................................................. 71

Specifications

CPU Supports 2nd and 3rd Gen AMD Ryzen™ / Ryzen™ with

Radeon™ Vega Graphics and 2nd Gen AMD Ryzen™ with

Radeon™ Graphics Desktop Processors for Socket AM4

Chipset AMD® X570 Chipset

Memory

∙4x DDR4 memory slots, support up to 128GB*

▪3rd Gen AMD Ryzen™ Processors support DDR4 1866/

2133/ 2400/ 2667/ 2800/ 2933/ 3000/ 3066/ 3200 Mhz by

JEDEC, and 2667/ 2800/ 2933/ 3000/ 3066/ 3200/ 3466/

3600/ 3733/ 3866/ 4000/ 4133/ 4266/ 4400/ 4533/ 4600+

Mhz by A-XMP OC MODE

▪2nd Gen AMD Ryzen™ Processors, 1st and 2nd Gen

AMD Ryzen™ with Radeon™ Vega Graphics Processors

support DDR4 1866/ 2133/ 2400/ 2667/ 2800/ 2933/ 3000/

3066/ 3200 Mhz by JEDEC, and 2667/ 2800/ 2933/ 3000/

3066/ 3200/ 3466+ Mhz by A-XMP OC MODE

∙Supports 1DPC 1R max speed 4600 MHZ

∙Supports 1DPC 2R max speed 3866 MHZ

∙Supports 2DPC 1R max speed 4000 MHZ

∙Supports 2DPC 2R max speed 3600 MHZ

∙Dual channel memory architecture

∙Supports non-ECC UDIMM memory

∙Supports ECC UDIMM memory (non-ECC mode)

∙Supports un-buffered memory

* Please refer www.msi.com for more information on compatible memory.

Expansion Slot

∙1x PCIe 4.0/ 3.0 x16 slot (PCI_E1)

▪3rd Gen AMD Ryzen™ support PCIe 4.0 x16 mode

▪2nd Gen AMD Ryzen™ support PCIe 3.0 x16 mode

▪Ryzen™ with Radeon™ Vega Graphics and 2nd Gen

AMD Ryzen™ with Radeon™ Graphics support PCIe 3.0

x8 mode

∙1x PCIe 4.0/ 3.0 x16 slot (PCI_E3, supports x4 mode)

∙2x PCIe 3.0 x1 slots

* The speeds may vary for different devices

Continued on next page

16 Specifications

Continued from previous page

Onboard Graphics

∙1x HDMI 1.4 port, supports a maximum resolution of

4096x2160 @24Hz*

* Only support when using Ryzen™ with Radeon™ Vega Graphics and 2nd Gen

AMD Ryzen™ with Radeon™ Graphics Processors

* Maximum shared memory of 2048 MB

Multi-GPU ∙Supports 2-Way AMD® CrossFire™ Technology

LAN ∙1x Realtek® 8125B 2.5Gbps LAN Controller

Wireless LAN &

Bluetooth®

Intel® Wi-Fi 6 AX200

▪Supports 802.11 a/b/g/n/ac/ax, MU-MINO Rx, 2.4GHz-

5GHz (160MHz) up to 2.4Gbps

▪Supports Bluetooth® 5

▪The Wireless module is pre-install in the M2_WIFI1

(Key-E) slot

Storage

∙6x SATA 6Gb/s ports (from AMD® X570 Chipset)

∙2x M.2 slots (Key M)*

▪M2_1 slot (from AMD® Processor)

▫Supports PCIe 4.0 x4 (3rd Gen AMD Ryzen™)

▫Supports PCIe 3.0 x4 (2nd Gen AMD Ryzen™/

Ryzen™ with Radeon™ Vega Graphics and 2nd Gen

AMD Ryzen™ with Radeon™ Graphics)

▫Supports 2242/ 2260/ 2280/ 22110 storage devices

▪M2_2 slot (from AMD® X570 Chipset)

▫Supports PCIe 4.0 x4 (3rd Gen AMD Ryzen™)

▫Supports PCIe 3.0 x4 (2nd Gen AMD Ryzen™/

Ryzen™ with Radeon™ Vega Graphics and 2nd Gen

AMD Ryzen™ with Radeon™ Graphics)

▫Supports SATA 6Gb/s

▫Supports 2242/ 2260/ 2280 storage devices

RAID ∙Supports RAID 0, RAID 1 and RAID 10

Audio

Realtek® ALC1200 Codec

∙7.1-Channel High Definition Audio

∙Supports Optical S/PDIF output

I/O Controller NUVOTON NCT6797 Controller Chip

Continued on next page

Specifications

Continued from previous page

Hardware Monitor

∙CPU/ System/ Chipset temperature detection

∙CPU/ System/ Chipset fan speed detection

∙CPU/ System/ Chipset fan speed control

USB

∙AMD® X570 Chipset

▪3x USB 3.2 Gen 2 10Gbps ports (2 Type-A ports on the

back panel, 1 Type-C internal connector)

▪4x USB 3.2 Gen 1 5Gbps ports available through the

internal USB 3.2 Gen 1 5Gbps connectors

▪6x USB 2.0 ports (2 Type-A ports on the back panel, 4

ports available through the internal USB 2.0 connectors)

∙AMD® Processor

▪2x USB 3.2 Gen 2 10Gbps (3rd Gen AMD Ryzen™) or

USB 3.2 Gen 1 5Gbps (2nd Gen AMD Ryzen™/ Ryzen™

with Radeon™ Vega Graphics and 2nd Gen AMD Ryzen™

with Radeon™ Graphics) ports (1x Type-A & 1x Type-C)

on the back panel

▪2x USB 3.2 Gen 1 5Gbps Type-A ports on the back

panel

Back Panel

Connectors

∙1x Flash BIOS Button

∙1x PS/2 keyboard/ mouse combo port

∙2x USB 2.0 ports

∙2x WiFi/ Bluetooth antenna jacks

∙2x USB 3.2 Gen 1 5Gbps ports

∙1x HDMI port

∙1x USB 3.2 Gen 2 10Gbps/ Gen 1 5Gbps Type A port

∙1x USB 3.2 Gen 2 10Gbps/ Gen 1 5Gbps Type C port

∙1x LAN(RJ45) port

∙2x USB 3.2 Gen 2 10Gbps Type A ports

∙5x audio jacks

∙1x Optical S/PDIF Out connector

Continued on next page

18 Specifications

Continued from previous page

Internal Connectors

∙1x 24-pin ATX main power connector

∙1x 8-pin ATX 12V power connector

∙1x 4-pin ATX 12V power connector

∙6x SATA 6Gb/s connectors

∙2x USB 2.0 connectors (supports additional 4 USB 2.0

ports)

∙2x USB 3.2 Gen 1 5Gbps connectors (supports additional 4

USB 3.2 Gen 1 5Gbps ports)

∙1x USB 3.2 Gen 2 10Gbps Type-C Port

∙1x 4-pin CPU fan connector

∙1x 4-pin water-pump connector

∙4x 4-pin system fan connectors

∙1x Front panel audio connector

∙2x System panel connectors

∙1x TPM module connector

∙1x Serial port connector

∙1x Clear CMOS jumper

∙1x Chassis Intrusion connector

∙2x 4-pin RGB LED connectors

∙2x 3-pin RAINBOW LED connectors

∙4x EZ Debug LEDs

∙1x TBT connector*

∙1x RTD3 connector

* Thunderbolt card needs to support RTD3.

BIOS Features

∙1x 256 Mb flash

∙UEFI AMI BIOS

∙ACPI 6.1, SM BIOS 2.8

∙Multi-language

Form Factor ∙ATX Form Factor

∙12 in. x 9.6 in. (30.5 cm x 24.4 cm)

Continued on next page

Specifications

Continued from previous page

Software

∙Drivers

∙DRAGON CENTER

∙CPU-Z MSI GAMING

∙Open Broadcaster Software (OBS)

∙MSI App Player (BlueStacks)

∙Google Chrome™ ,Google Toolbar, Google Drive

∙Norton™ Internet Security Solution

Dragon Center

Features

∙Gaming Mode

∙Gaming Hotkey

∙LAN Manager

∙Mystic Light

∙Ambient Link

∙User Scenario

∙Monitor(Hardware

Monitor)

∙True Color

∙Live Update

∙Speed Up

∙Smart Tool

∙Super Charger

Please refer to http://download.msi.

com/manual/mb/DRAGONCENTER2.

pdf for more details.

Special Features

∙Audio

▪Audio Boost

∙Network

▪2.5G LAN

▪Intel WiFi 6

∙Cooling

▪Frozr Heatsink Design

▪Propeller Blade technology

▪M.2 Shield Frozr

▪Extended Heatsink Design

▪Pump Fan

▪Smart Fan Control

Continued on next page

20 Specifications

Continued from previous page

Special Features

∙Storage

▪Lightning Gen 4 M.2

▪Twin Turbo M.2

∙LED

▪Mystic Light 3

▪Mystic Light Extension (RGB)

▪Mystic Light Extension (RAINBOW)

▪Mystic Light Sync

▪EZ DEBUG LED

∙Protection

▪PCIe Steel Armor

▪PCIe Steel Slot

▪Pre-installed IO shielding

∙Performance

▪Lightning Gen 4 PCI-E Slot

▪Multi GPU-CrossFire Technology

▪DDR4 Boost

▪Core Boost

▪GAME Boost

▪USB with type A+C

▪AMD Turbo USB 3.2 Gen 2

▪Dual CPU Power

∙BIOS

▪Click BIOS 5

▪Flash BIOS Button

∙Gamer Experience

▪DRAGON CENTER

▪GAMING HOTKEY

▪GAMING MOUSE Control

▪USB SPEED UP

▪Total Fan control

▪Live Update

▪APP Player

Package contents

Please check the contents of your motherboard package. It should contain:

Motherboard MAG X570 TOMAHAWK WIFI

Cable SATA 6Gb/s cables (2 cables/pack) 1

Accessories

Wi-Fi antenna 1

M.2 screws (3 pcs./pack) 1

Case badge 1

Product registration card 1

Application DVD Driver DVD 1

Documentation User manual 1

Quick installation guide 1

⚠

Important

If any of the above items are damaged or missing, please contact your retailer.

22 Block Diagram

Block Diagram

2 Channel DDR4 Memory

2x USB 3.2 Gen 1

PCIE

PCI Express Bus

PCH

Processor

NUVOTON

6797

Realtek

ALC1200

4x USB 3.2 Gen 1

3x USB 3.2 Gen 2

6x USB 2.0

Rear Audio Jacks

Front Audio Jacks

1x M.2

1x Intel Wi-Fi 6

6x SATA 6Gb/s

1x M.2 2x USB 3.2 Gen 2

1x Realtek 8125B 2.5Gbps LAN

2x PCIex1

P/S2 Mouse/ Keyboard

Rear I/O Panel

Link/ Activity LED

Status Description

Off No link

Yellow Linked

Blinking Data activity

Speed LED

Status Description

Off 10 Mbps connection

Green 100 Mbps/ 1 Gbps

Orange 2.5 Gbps connection

LAN Port LED Status Table

Audio Ports Configuration

Audio Ports Channel

2468

Center/ Subwoofer Out  

Rear Speaker Out 

Line-In/ Side Speaker Out 

Line-Out/ Front Speaker Out 

Mic In

(: connected, Blank: empty)

USB 3.2 Gen 2

10Gbps Type-C*

USB 3.2 Gen 2

10Gbps Type-A*

PS/2 2.5Gbps

LAN

USB 2.0 Type-A

Audio Ports

Optical S/PDIF-Out

Flash BIOS

Button

Flash BIOS

Port USB 3.2 Gen 2

10Gbps Type-A

*USB 3.2 Gen 2 10Gbps (3rd Gen AMD Ryzen™) or USB 3.2 Gen 1 5Gbps (2nd Gen

AMD Ryzen™/Ryzen™ with Radeon™ Vega Graphics and 2nd Gen AMD Ryzen™ with

Radeon™Graphics)

∙Flash BIOS Port/ Button - Please refer to page 47 for Updating BIOS with Flash BIOS

Button.

Wi-Fi Antenna

connectors

USB 3.2 Gen 1

5Gbps Type-A

24 Rear I/O Panel

Realtek Audio Console

After Realtek Audio Console is installed. You can use it to change sound settings to get

better sound experience.

∙Device Selection - allows you to select a audio output source to change the related

options. The check sign indicates the devices as default.

∙Application Enhancement - the array of options will provide you a complete

guidance of anticipated sound effect for both output and input device.

∙Main Volume - controls the volume or balance the right/left side of the speakers

that you plugged in front or rear panel by adjust the bar.

∙Jack Status - depicts all render and capture devices currently connected with your

computer.

∙Connector Settings - configures the connection settings.

Auto popup dialog

When you plug into a device at an audio jack, a dialogue window will pop up asking you

which device is current connected.

Each jack corresponds to its default setting as shown on the next page.

⚠

Important

The pictures above for reference only and may vary from the product you purchased.

Jack Status

Connector Settings

Device

Selection

Main Volume

Application Enhancement

Rear I/O Panel

Audio jacks to headphone and microphone diagram

Audio jacks to stereo speakers diagram

Audio jacks to 7.1-channel speakers diagram

AUDIO INPUT

Rear Front

Side Center/

Subwoofer

26 Rear I/O Panel

Installing antennas

1. Screw the antennas tight to the antenna connectors as shown below.

2. Orient the antennas.

Overview of Components

BAT1

JRAINBOW1

JFP1





M2_1

JUSB4

M2_2



JFP2

CPU_FAN1

PUMP_FAN1

PCI_E1

PCI_E2

JBAT1

JTBT1

PCI_E3

JCI1

JRTD3

PCI_E4

JAUD1

JRGB1

Processor

Socket

CPU_PWR1

CPU_PWR2

JRGB2

JRAINBOW2

JUSB2 JUSB3

JUSB1

JCOM1

JTPM1

SYS_FAN4

SYS_FAN3

SYS_FAN2

SYS_FAN1

ATX_PWR1

JUSB5

DIMMB2

DIMMB1

DIMMA2

DIMMA1

28 Overview of Components

Component Contents

Port Name Port Type Page

CPU_FAN1, PUMP_FAN1,

SYS_FAN1~4 Fan Connectors 36

CPU_PWR1~2, ATX_PWR1 Power Connectors 35

CPU Socket AM4 CPU Socket 29

DIMMA1/A2/B1/B2 DIMM Slots 30

JAUD1 Front Audio Connector 38

JBAT1 Clear CMOS (Reset BIOS) Jumper 41

JCI1 Chassis Intrusion Connector 40

JCOM1 Serial Port Connector 40

JFP1, JFP2 Front Panel Connectors 34

JRAINBOW1~2 Addressable RGB LED connectors 43

JRGB1~2 RGB LED connectors 42

JRTD3 Intel RTD3 Connector 39

JTBT1 Thunderbolt Add-on Card Connector 39

JUSB1~2 USB 2.0 Connectors 37

JUSB3~4 USB 3.2 Gen 1 5Gbps Connectors 37

JUSB5 USB 3.2 Gen 2 10Gbps Type-C Connector 38

M2_1~2 M.2 Slots (Key M) 32

PCI_E1~4 PCIe Expansion Slots 31

SATA1~6 SATA 6Gb/s Connectors 34

Overview of Components

CPU Socket

Introduction to the AM4 CPU

The surface of the AM4 CPU has a

yellow triangle to assist in correctly

lining up the CPU for motherboard

placement. The yellow triangle is

the Pin 1 indicator.

53.2 mm

Distance from the center of the

CPU to the nearest DIMM slot.

⚠

Important

∙

When changing the processor, the system configuration could be cleared and reset

BIOS to default values, due to the AM4 processor’s architecture.

∙

Always unplug the power cord from the power outlet before installing or removing

the CPU.

∙

When installing a CPU, always remember to install a CPU heatsink. A CPU heatsink

is necessary to prevent overheating and maintain system stability.

∙

Confirm that the CPU heatsink has formed a tight seal with the CPU before booting

your system.

∙

Overheating can seriously damage the CPU and motherboard. Always make sure

the cooling fans work properly to protect the CPU from overheating. Be sure to apply

an even layer of thermal paste (or thermal tape) between the CPU and the heatsink to

enhance heat dissipation.

∙

If you purchased a separate CPU and heatsink/ cooler, Please refer to the

documentation in the heatsink/ cooler package for more details about installation.

∙

This motherboard is designed to support overclocking. Before attempting to

overclock, please make sure that all other system components can tolerate

overclocking. Any attempt to operate beyond product specifications is not

recommended. MSI

does not guarantee the damages or risks caused by inadequate

operation beyond product specifications.

30 Overview of Components

DIMM Slots

DIMMA1 DIMMB1

Channel A Channel B

DIMMA2 DIMMB2

Memory module installation recommendation

DIMMB2 DIMMB2

DIMMB1

DIMMA2 DIMMA2 DIMMA2

DIMMA1

⚠

Important

∙

Always insert memory modules in the DIMMA2 slot first.

∙

To ensure system stability for Dual channel mode, memory modules must be of the

same type, number and density.

∙

Some memory may operate at a lower frequency than the marked value when

overclocking due to the memory frequency operates dependent on its Serial Presence

Detect (SPD). Go to BIOS and find the DRAM Frequency to set the memory frequency if

you want to operate the memory at the marked or at a higher frequency.

∙

It is recommended to use a more efficient memory cooling system for full DIMMs

installation or overclocking.

∙

The stability and compatibility of installed memory module depend on installed CPU

and devices when overclocking.

∙

Please refer www.msi.com for more information on compatible memory.

Overview of Components

PCI_E1~4: PCIe Expansion Slots

⚠

Important

∙

If you install a large and heavy graphics card, you need to use a tool such as MSI

Gaming Series Graphics Card Bolster to support its weight to prevent deformation of

the slot.

∙

For a single PCIe x16 expansion card installation with optimum performance, using

the PCI_E1 slot is recommended.

∙

When adding or removing expansion cards, always turn off the power supply and

unplug the power supply power cable from the power outlet. Read the expansion

card’s documentation to check for any necessary additional hardware or software

changes.

Slots 3rd Gen AMD

Ryzen™ 2nd Gen AMD

Ryzen™

Ryzen™ with Radeon™

Vega Graphics and 2nd

Gen AMD Ryzen™ with

Radeon™ Graphics

PCI_E1 (CPU) PCIe 4.0 x16 PCIe 3.0 x16 PCIe 3.0 x8

PCI_E2 (PCH) PCIe 3.0 x1 PCIe 3.0 x1 PCIe 3.0 x1

PCI_E3 (PCH) PCIe 4.0 x4 PCIe 3.0 x4 PCIe 3.0 x4

PCI_E4 (PCH) PCIe 3.0 x1 PCIe 3.0 x1 PCIe 3.0 x1

BAT1

PCI_E1: PCIe x16 slot (CPU)

PCI_E3: PCIe x16 slot (PCH)

PCI_E4: PCIe x1 slot (PCH)

PCI_E2: PCIe x1 slot (PCH)

32 Overview of Components

M2_1~2: M.2 Slots (Key M)

M2_1

M2_2

M.2 installation

1. Loosen the screws of M.2 heatsink.

2. Remove the M.2 hearsink and remove the protective film from the thermal pad.

The following table describes the relationship between the

M.2 slots and the PCIe bandwidth of the processors.

Slots 3rd Gen AMD

Ryzen™

2nd Gen AMD

Ryzen™

Ryzen™ with

Radeon™ Vega

Graphics and 2nd Gen

AMD Ryzen™ with

Radeon™ Graphics

M2_1

(CPU) PCIe 4.0 x4 PCIe 3.0 x4 PCIe 3.0 x4

M2_2

(PCH) PCIe 4.0 x4 PCIe 3.0 x4 PCIe 3.0 x4

Overview of Components

30º30º

M.2 standoff

heatsink standoff

M.2 screw

6. Put the M.2 heatsink back in place and secure it.

3. Move and fasten the M.2 standoff to the appropriate position for your M.2 SSD if

need, or remove the M.2 standoff if your M.2 SSD length is same as the length of

M.2 heatsink.

4. Insert your M.2 SSD into the M.2 slot at a 30-degree angle.

5. Secure the M.2 SSD in place with the M.2 screw, or skip this step if you remove the

M.2 standoff in step 3.

34 Overview of Components

JFP1, JFP2: Front Panel Connectors

These connectors connect to the switches and LEDs on the front panel.

2 10

+- --

Power LED

HDD LED Reset Switch

Reserved

Power Switch

JFP1

1 HDD LED + 2 Power LED +

3 HDD LED - 4 Power LED -

5 Reset Switch 6 Power Switch

7 Reset Switch 8 Power Switch

9 Reserved 10 No Pin

JFP2

Speaker

Buzzer 1 Speaker - 2 Buzzer +

3 Buzzer - 4 Speaker +

SATA1~6: SATA 6Gb/s Connectors

These connectors are SATA 6Gb/s interface ports. Each connector can connect to one

SATA device.

⚠

Important

∙

Please do not fold the SATA cable at a 90-degree angle. Data loss may result during

transmission otherwise.

∙

SATA cables have identical plugs on either sides of the cable. However, it is

recommended that the flat connector be connected to the motherboard for space

saving purposes.

SATA5

SATA3

SATA6

SATA4

SATA1

SATA2

Overview of Components

131

ATX_PWR1

1 +3.3V 13 +3.3V

2 +3.3V 14 -12V

3 Ground 15 Ground

4 +5V 16 PS-ON#

5 Ground 17 Ground

6 +5V 18 Ground

7 Ground 19 Ground

8 PWR OK 20 Res

9 5VSB 21 +5V

10 +12V 22 +5V

11 +12V 23 +5V

12 +3.3V 24 Ground

4 1

8CPU_PWR1

1 Ground 5 +12V

2 Ground 6 +12V

3 Ground 7 +12V

4 Ground 8 +12V

⚠

Important

Make sure that all the power cables are securely connected to a proper ATX power

supply to ensure stable operation of the motherboard.

CPU_PWR1~2, ATX_PWR1: Power Connectors

These connectors allow you to connect an ATX power supply.

2 1

4CPU_PWR2

1 Ground 3 +12V

2 Ground 4 +12V

36 Overview of Components

Switching fan mode and adjusting fan speed

You can switch between PWM mode and DC mode and adjust fan speed in BIOS >

HARDWARE MONITOR.

Select PWM mode or DC mode

⚠

Important

Make sure fans are working properly after switching the PWM/ DC mode.

There are gradient points of the fan speed that allow you to adjust

fan speed in relation to CPU temperature.

PWM Mode pin definition

1 Ground 2 +12V

3 Sense 4 Speed Control Signal

DC Mode pin definition

1 Ground 2 Voltage Control

3 Sense 4 NC

Pin definition of fan connectors

CPU_FAN1, PUMP_FAN1, SYS_FAN1~4: Fan Connectors

Fan connectors can be classified as PWM (Pulse Width Modulation) Mode or DC Mode.

PWM Mode fan connectors provide constant 12V output and adjust fan speed with

speed control signal. DC Mode fan connectors control fan speed by changing voltage.

You can follow the instruction below to adjust the fan connector to PWM or DC Mode.

PUMP_FAN1

(Default PWM mode)

SYS_FAN1~4

(Default DC mode)

CPU_FAN1

(Default PWM Mode)

Overview of Components

JUSB3~4: USB 3.2 Gen 1 5Gbps Connectors

These connectors allow you to connect USB 3.2 Gen 1 5Gbps ports on the front panel.

⚠

Important

Note that the Power and Ground pins must be connected correctly to avoid possible

damage.

10 11

JUSB4

1 10

1120

JUSB3

1 Power 11 USB2.0+

2 USB3_RX_DN 12 USB2.0-

3 USB3_RX_DP 13 Ground

4 Ground 14 USB3_TX_C_DP

5 USB3_TX_C_DN 15 USB3_TX_C_DN

6 USB3_TX_C_DP 16 Ground

7 Ground 17 USB3_RX_DP

8 USB2.0- 18 USB3_RX_DN

9 USB2.0+ 19 Power

10 NC 20 No Pin

JUSB1~2: USB 2.0 Connectors

These connectors allow you to connect USB 2.0 ports on the front panel.

2 10

1 VCC 2 VCC

3 USB0- 4 USB1-

5 USB0+ 6 USB1+

7 Ground 8 Ground

9 No Pin 10 NC

⚠

Important

∙

Note that the VCC and Ground pins must be connected correctly to avoid possible

damage.

∙

In order to recharge your iPad,iPhone and iPod through USB ports, please install

MSI

DRAGON CENTER utility.

38 Overview of Components

JAUD1: Front Audio Connector

This connector allows you to connect audio jacks on the front panel.

2 10

1 MIC L 2 Ground

3 MIC R 4 NC

5 Head Phone R 6 MIC Detection

7 SENSE_SEND 8 No Pin

9 Head Phone L 10 Head Phone Detection

JUSB5: USB 3.2 Gen 2 10Gbps Type-C Connector

This connector allows you to connect USB 3.2 Gen 2 10Gbps Type-C connector on the

front panel. The connector possesses a foolproof design. When you connect the cable,

be sure to connect it with the corresponding orientation.

JUSB5 USB Type-C Cable

USB Type-C port on

the front panel

Overview of Components

JTBT1: Thunderbolt Add-on Card Connector

This connector allows you to connect the add-on Thunderbolt I/O card.

JTBT1

1 FORCE_PWR 2 SCI_EVENT

3 SLP_S3# 4 SLP_S5#

5 Ground

JRTD3

1 WAKE 2 PWR EN

3 GND

JRTD3: Intel RTD3 Connector

This connector allows you to connect the RTD3 connector on the add-on Thunderbolt

I/O card that supports RTD3.

40 Overview of Components

JCI1: Chassis Intrusion Connector

This connector allows you to connect the chassis intrusion switch cable.

Normal

(default)

Trigger the chassis

intrusion event

Using chassis intrusion detector

1. Connect the JCI1 connector to the chassis intrusion switch/ sensor on the chassis.

2. Close the chassis cover.

3. Go to BIOS > SETTINGS > Security > Chassis Intrusion Configuration.

4. Set Chassis Intrusion to Enabled.

5. Press F10 to save and exit and then press the Enter key to select Yes.

6. Once the chassis cover is opened again, a warning message will be displayed on

screen when the computer is turned on.

Resetting the chassis intrusion warning

1. Go to BIOS > SETTINGS > Security > Chassis Intrusion Configuration.

2. Set Chassis Intrusion to Reset.

3. Press F10 to save and exit and then press the Enter key to select Yes.

2 10

1 DCD 2 SIN

3 SOUT 4 DTR

5 Ground 6 DSR

7 RTS 8 CTS

9 RI 10 No Pin

JCOM1: Serial Port Connector

This connector allows you to connect the optional serial port with bracket.

Overview of Components

JBAT1: Clear CMOS (Reset BIOS) Jumper

There is CMOS memory onboard that is external powered from a battery located on

the motherboard to save system configuration data. If you want to clear the system

configuration, set the jumper to clear the CMOS memory.

Keep Data

(default) Clear CMOS/

Reset BIOS

Resetting BIOS to default values

1. Power off the computer and unplug the power cord

2. Use a jumper cap to short JBAT1 for about 5-10 seconds.

3. Remove the jumper cap from JBAT1.

4. Plug the power cord and power on the computer.

EZ Debug LED

These LEDs indicate the debug status of the motherboard.

CPU - indicates CPU is not detected or fail.

DRAM - indicates DRAM is not detected or fail.

VGA - indicates GPU is not detected or fail.

BOOT - indicates the booting device is not detected

or fail.

42 Overview of Components

⚠

Important

∙

An JRGB connector supports up to 2 meters continuous 5050 RGB LED strips

(12V/G/R/B) with the maximum power rating of 3A (12V).

∙

Always turn off the power supply and unplug the power cord from the power outlet

before installing or removing the RGB LED strip.

∙

Please use MSI’s software to control the extended LED strip.

JRGB1~2: RGB LED connectors

The JRGB connectors allow you to connect the 5050 RGB LED strips 12V.

GRB

JRGB

connector

RGB extension

cable (optional) 5050 RGB LED strips 12V

1 +12V 2 G

3 R 4 B

RGB LED Strip Connection

GRB

JRGB connector

System Fan connector

RGB LED Fan Connection

RGB LED Fan

Overview of Components

+5V

⚠

CAUTION

Do not connect the wrong type of LED strips. The JRGB connector and the JRAINBOW

connector provide different voltages, and connecting the 5V LED strip to the JRGB

connector will result in damage to the LED strip.

⚠

Important

∙

The JRAINBOW connector supports up to 75 LEDs WS2812B Individually

Addressable RGB LED strips (5V/Data/Ground) with the maximum power rating of 3A

(5V). In the case of 20% brightness, the connector supports up to 200 LEDs.

∙

Always turn off the power supply and unplug the power cord from the power outlet

before installing or removing the RGB LED strip.

∙

Please use MSI’s software to control the extended LED strip.

JRAINBOW1~2: Addressable RGB LED connectors

The JRAINBOW connectors allow you to connect the WS2812B Individually

Addressable RGB LED strips 5V.

JRAINBOW

connector

JRAINBOW connector

System Fan connector

Rainbow RGB LED

extension cable

(optional)

WS2812B Individually

Addressable RGB LED strips 5V

1 +5V 2 Data

3 No Pin 4 Ground

Addressable RGB LED Strip Connection

Addressable RGB LED Fan Connection

Addressable RGB LED Fan

44 Installing OS, Drivers & Utilities

Installing OS, Drivers & Utilities

Please download and update the latest utilities and drivers at www.msi.com

Installing Windows® 10

1. Power on the computer.

2. Insert the Windows® 10 installation disc/USB into your computer.

3. Press the Restart button on the computer case.

4. Press F11 key during the computer POST (Power-On Self Test) to get into Boot

Menu.

5. Select the Windows® 10 installation disc/USB from the Boot Menu.

6. Press any key when screen shows Press any key to boot from CD or DVD...

message.

7. Follow the instructions on the screen to install Windows® 10.

Installing Drivers

1. Start up your computer in Windows® 10.

2. Insert MSI® Driver Disc into your optical drive.

3. Click the Select to choose what happens with this disc pop-up notification, then

select Run DVDSetup.exe to open the installer. If you turn off the AutoPlay feature

from the Windows Control Panel, you can still manually execute the DVDSetup.exe

from the root path of the MSI Driver Disc.

4. The installer will find and list all necessary drivers in the Drivers/Software tab.

5. Click the Install button in the lower-right corner of the window.

6. The drivers installation will then be in progress, after it has finished it will prompt

you to restart.

7. Click OK button to finish.

8. Restart your computer.

Installing Utilities

Before you install utilities, you must complete drivers installation.

1. Open the installer as described above.

2. Click the Utilities tab.

3. Select the utilities you want to install.

4. Click the Install button in the lower-right corner of the window.

5. The utilities installation will then be in progress, after it has finished it will prompt

you to restart.

6. Click OK button to finish.

7. Restart your computer.

BIOS Setup

The default settings offer the optimal performance for system stability in normal

conditions. You should always keep the default settings to avoid possible system

damage or failure booting unless you are familiar with BIOS.

⚠

Important

∙

BIOS items are continuously update for better system performance. Therefore, the

description may be slightly different from the latest BIOS and should be for reference

only. You could also refer to the HELP information panel for BIOS item description.

∙

The pictures in this chapter are for reference only and may vary from the product

you purchased.

∙

The BIOS items will vary with the processor.

Entering BIOS Setup

Press Delete key, when the Press DEL key to enter Setup Menu, F11 to enter Boot

Menu message appears on the screen during the boot process.

Function key

F1: General Help list

F2: Add/ Remove a favorite item

F3: Enter Favorites menu

F4: Enter CPU Specifications menu

F5: Enter Memory-Z menu

F6: Load optimized defaults

F7: Switch between Advanced mode and EZ mode

F8: Load Overclocking Profile

F9: Save Overclocking Profile

F10: Save Change and Reset*

F12: Take a screenshot and save it to USB flash drive (FAT/ FAT32 format only).

Ctrl+F: Enter Search page

* When you press F10, a confirmation window appears and it provides the modification

information. Select between Yes or No to confirm your choice.

46 BIOS Setup

Resetting BIOS

You might need to restore the default BIOS setting to solve certain problems. There

are several ways to reset BIOS:

∙Go to BIOS and press F6 to load optimized defaults.

∙Short the Clear CMOS jumper on the motherboard.

⚠

Important

Be sure the computer is off before clearing CMOS data. Please refer to the Clear

CMOS jumper section for resetting BIOS.

Updating BIOS

Updating BIOS with M-FLASH

Before updating:

Please download the latest BIOS file that matches your motherboard model from MSI

website. And then save the BIOS file into the USB flash drive.

Updating BIOS:

1. Insert the USB flash drive that contains the update file into the USB port.

2. Please refer the following methods to enter flash mode.

▪Reboot and press Ctrl + F5 key during POST and click on Yes to reboot the

system.

▪Reboot and press Del key during POST to enter BIOS. Click the M-FLASH button

and click on Yes to reboot the system.

3. Select a BIOS file to perform the BIOS update process.

4. After the flashing process is 100% completed, the system will reboot

automatically.

Updating the BIOS with MSI DRAGON CENTER

Before updating:

Make sure the LAN driver is already installed and the internet connection is set

properly.

Updating BIOS:

1. Install and launch MSI DRAGON CENTER.

2. Select BIOS Update.

3. Click on Scan button.

4. Click on Download icon to download and install the latest BIOS file.

5. Click Next and choose In Windows mode. And then click Next and Start to start

updating BIOS.

6. After the flashing process is 100% completed, the system will restart

automatically.

BIOS Setup

Updating BIOS with Flash BIOS Button

1. Please download the latest BIOS file that matches your motherboard model from

the MSI® website.

2. Rename the BIOS file to MSI.ROM, and save it to the root of your USB flash drive

(FAT32 format).

3. Connect the power supply to CPU_PWR1 and ATX_PWR1. (No need to install CPU

and memory.)

4. Plug the USB flash drive that contains the MSI.ROM file into the Flash BIOS Port

on the rear I/O panel.

5. Press the Flash BIOS Button to flash BIOS, and the LED starts flashing.

6. The LED will be turned off when the process is completed.

⚠

Important

Only the FAT32 format USB flash drive supports updating BIOS by Flash BIOS Button.

To check your drive, go to Windows Explorer, right click on the drive icon and go to

Properties.

48 BIOS Setup

EZ Mode

At EZ mode, it provides the basic system information and allows you to configure the

basic setting. To configure the advanced BIOS settings, please enter the Advanced

Mode by pressing the Setup Mode switch or F7 function key.

A-XMP switch

Information

display

System

information

Boot device

priority bar

Function

buttons

Language

GAME BOOST

switch

Screenshot

Setup Mode switch

M-Flash

Hardware

Monitor

Favorites

∙GAME BOOST switch - click on it to toggle the GAME BOOST for OC.

⚠

Important

Please don’t make any changes in OC menu and don’t load defaults to keep the

optimal performance and system stability after activating the GAME BOOST function.

∙A-XMP switch (optional) - click on the inner circle to enable/ disable the A-XMP.

Switch the outer circle to select the memory profile if any. This switch will only be

available if the installed processor and memory modules support A-XMP function.

∙Setup Mode switch - press this tab or the F7 key to switch between Advanced mode

and EZ mode.

∙Screenshot - click on this tab or the F12 key to take a screenshot and save it to USB

flash drive (FAT/ FAT32 format only).

∙Search - click on this tab or the Ctrl+F keys to enter the search page. It allows you

to search by BIOS item name. Move the mouse over a blank space and right click the

mouse to exit the search page.

⚠

Important

In search page, only the F6, F10 and F12 function keys are available.

∙Language - allows you to select language of BIOS setup.

∙System information - shows the CPU/ DDR speed, CPU/ MB temperature, MB/ CPU

type, memory size, CPU/ DDR voltage, BIOS version and build date.

∙Boot device priority bar - you can move the device icons to change the boot priority.

The boot priority from high to low is left to right.

BIOS Setup

∙Information display - click on the CPU, Memory, Storage, Fan Info and Help buttons

on left side to display related information.

∙Function buttons - enable or disable the LAN Option ROM, ErP Ready, Indication

LED Control, CSM, AHCI and RGB Light Control by clicking on their respective button.

∙M-Flash - click on this button to display the M-Flash menu that provides the way to

update BIOS with a USB flash drive.

∙Hardware Monitor - click on this button to display the Hardware Monitor menu that

allows you to manually control the fan speed by percentage.

∙Favorites - press the F3 key to enter Favorites menu. It allows you to create

personal BIOS menu where you can save and access favorite/ frequently-used BIOS

setting items.

▪Default HomePage - allows you to select a BIOS menu (e.g. SETTINGS, OC...,etc)

as the BIOS home page.

▪Favorite1~5 - allows you to add the frequently-used/ favorite BIOS setting items

in one page.

▪To add a BIOS item to a favorite page (Favorite 1~5)

1. Move the mouse over a BIOS item not only on BIOS menu but also on search

page.

2. Right-click or press F2 key.

3. Choose a favorite page and click on OK.

▪To delete a BIOS item from favorite page

1. Move the mouse over a BIOS item on favorite page (Favorite 1~5)

2. Right-click or press F2 key.

3. Choose Delete and click on OK.

50 BIOS Setup

Advanced Mode

Press Setup Mode switch or F7 function key can switch between EZ Mode and

Advanced Mode in BIOS setup.

A-XMP switch

GAME BOOST

switch

System

information

Boot device

priority bar

BIOS menu

selection

Language

Screenshot

Setup Mode switch

Menu display

BIOS menu

selection

∙BIOS menu selection - the following options are available:

▪SETTINGS - allows you to specify the parameters for chipset and boot devices.

▪OC - allows you to adjust the frequency and voltage. Increasing the frequency

may get better performance.

▪M-FLASH - provides the way to update BIOS with a USB flash drive.

▪OC PROFILE - allows you to manage overclocking profiles.

▪HARDWARE MONITOR - allows you to set the speeds of fans and monitor

voltages of system.

▪BOARD EXPLORER - provides the information of installed devices on this

motherboard.

∙Menu display - provides BIOS setting items and information to be configured.

BIOS Setup

SETTINGS

System Status

▶System Date

Sets the system date. Use tab key to switch between date elements.

The format is <day> <month> <date> <year>.

<day> Day of the week, from Sun to Sat, determined by BIOS. Read-only.

<month> The month from Jan. through Dec.

<date> The date from 1 to 31 can be keyed by numeric function keys.

<year> The year can be adjusted by users.

▶System Time

Sets the system time. Use tab key to switch between time elements.

The time format is <hour> <minute> <second>.

▶SATA PortX

Shows the information of connected SATA device.

⚠

Important

If the connected SATA device is not displayed, turn off computer and re-check SATA

cable and power cable connections of the device and motherboard.

▶System Information

Shows detailed system information, including CPU type, BIOS version, and Memory

(read only).

▶DMI Information

Shows system information, desktop Board Information and chassis Information. (Read

only).

Advanced

▶PCI Subsystem Settings

Sets PCI, PCI express interface protocol and latency timer. Press Enter to enter the

sub-menu.

52 BIOS Setup

▶Above 4G memory/ Crypto Currency mining [Disabled]

Enables or disables 64-bit capable devices to be decoded in above 4G address

space. It is only available if the system supports 64-bit PCI decoding.

[Enabled] Allows you to utilize more than 4x GPUs.

[Disabled] Disables this function.

▶PCH Gen Switch [Auto]

󽙋

devices.



[Gen1] Enables PCIe Gen1 support only.

[Gen2] Enables PCIe Gen2 support only.

[Gen3] Enables PCIe Gen3 support only.

[Gen4] Enables PCIe Gen4 support only.

▶PCIe SlotX Lanes Configuration



PCIe storage card. The options in this item will vary with the installed processor.

▶ACPI Settings

Sets ACPI parameters of onboard power LED behaviors. Press Enter to enter the sub-

menu.

▶Power LED [Blinking]

Sets shining behaviors of the onboard Power LED.

[Dual Color] The power LED turns to another color to indicate the S3 state.

[Blinking] The power LED blinks to indicate the S3 state.

▶CPU Over Temperature Alert [Auto]

Enables or disables the CPU overheating alert sound and message when CPU

temperature is over 55 and 75 degrees centigrade.

▶Integrated Peripherals

Sets integrated peripherals' parameters, such as LAN, HDD, USB and audio. Press

Enter to enter the sub-menu.

▶Onboard LAN Controller [Enabled]

Enables or disables the onboard LAN controller.

▶LAN Option ROM [Disabled]

Enables or disables the legacy network Boot Option ROM for detailed settings. This

item will appear when Onboard LAN Controller is enabled.

[Enabled] Enables the onboard LAN Boot ROM.

[Disabled] Disables the onboard LAN Boot ROM.

▶Network Stack [Disabled]

Sets UEFI network stack for optimizing IPv4 / IPv6 function. This item is available

when Onboard LAN Controller is Enabled.

[Enabled] Enables UEFI network stack.

[Disabled] Disables UEFI network stack.

BIOS Setup

▶Ipv4 PXE Support [Enabled]

When Enabled, the system UEFI network stack will support Ipv4 protocol. This item

will appear when Network Stack is Enabled.

[Enabled] Enables the Ipv4 PXE boot support.

[Disabled] Disables the Ipv4 PXE boot support.

▶Ipv6 PXE Support [Enabled]

When Enabled, the system UEFI network stack will support Ipv6 protocol. This item

will appear when Network Stack is enabled.

[Enabled] Enables the Ipv6 PXE boot support.

[Disabled] Disables the Ipv6 PXE boot support.

▶SATA Mode [AHCI Mode]

Sets the operation mode of the onboard SATA controller.

[AHCI Mode] Specify the AHCI mode for SATA storage devices. AHCI (Advanced

󽙋

the speed and performance of SATA storage device, such as Native

Command Queuing (NCQ) and hot-plugging.

[RAID Mode] Enables RAID function for SATA storage devices.

▶SATAx Hot Plug [Disabled]

Allows user to enable or disable the SATA hot plug support.

[Enabled] Enables hot plug support for the SATA ports.

[Disabled] Disables hot plug support for the SATA ports.

▶HD Audio Controller [Enabled]



▶ Integrated Graphics Conguration (optional)

Adjusts integrated graphics settings for optimum system. Press Enter to enter the

sub-menu.

▶Initiate Graphic Adapter [PEG] (optional)

Selects a graphics device as the primary boot device.

[IGD] Integrated Graphics Display.

[PEG] PCI-Express Graphics Device.

▶Integrated Graphics [Auto] (optional)

If set to Force, BIOS will enable the integrated graphics controller.

▶UMA Frame Buffer Size [Auto] (optional)



item will be available when Integrated Graphics is enabled.

▶ USB Conguration

Sets the onboard USB controller and device function. Press Enter to enter the sub-

menu.

▶XHCI Hand-off [Enabled]

󽙋

󽙋

54 BIOS Setup

▶Legacy USB Support [Enabled]

Sets Legacy USB function support.

[Auto] The system will automatically detect if any USB device is connected

and enable the legacy USB support.

[Enabled] Enable the USB support under legacy mode.

[Disabled] The USB devices will be unavailable under legacy mode.

▶ Super IO Conguration

Sets system Super I/O chip parameters including COM port. Press Enter to enter the

sub-menu.

▶Serial (COM) Port x Configuration

Enter to enter the sub-

menu.

▶Serial (COM) Port x [Enabled]

Enables or disables serial (COM) port x.

▶Serial (COM) Port x Settings [Auto]

Sets serial port x (COM). If set to Auto, BIOS will optimize the IRQ automatically or

you can set it manually.

▶Power Management Setup

Sets system Power Management of ErP and AC Power Loss behaviors. Press Enter to

enter the sub-menu.

▶ErP Ready [Disabled]

Enables or disables the system power consumption according to ErP regulation.

[Enabled] Optimize the system power consumption according to ErP

regulation. It will not support S4 & S5 wake up by USB, PCI and PCIe

devices.

[Disabled] Disables this function.

▶Restore after AC Power Loss [Power Off]

Sets the system behaviors while encountering the AC power loss.

󽙋 󽙋

[Power On] Boot up the system after restoring AC power.

 󽙋

before AC power loss.

▶System Power Fault Protection [Disabled]

Enables or disables the system to boot up when detecting abnormal voltage input.

[Enabled] Protect the system from unexpected power operating and remain

the shut down status.

[Disabled] Disables this function.

▶ Windows OS Conguration

Enter to enter the sub-

menu.

BIOS Setup

▶BIOS UEFI/CSM Mode [CSM]

Select CSM (Compatibility Support Module) or UEFI mode to meet the system

requirement.

[CSM] For the non-UEFI driver add-on devices or non-UEFI mode OS.

[UEFI] For the UEFI driver add-on devices and UEFI mode OS.

▶GOP Information

Shows the onboard Graphics Output Protocol (GOP) information. Press Enter to

enter the sub-menu. This sub-menu will appear when BIOS UEFI/CSM Mode sets

to UEFI.

▶Secure Boot

Sets the Windows secure boot to prevent the unauthorized accessing. Press Enter

to enter the sub-menu. This sub-menu will appear when BIOS UEFI/CSM Mode

sets to UEFI.

▶Wake Up Event Setup

Sets system wake up behaviors for different sleep modes. Press Enter to enter the

sub-menu.

▶Wake Up Event By [BIOS]

Selects the wake up event by BIOS or operating system.

[BIOS] Activates the following items, set wake up events of these items.

 

▶Resume By RTC Alarm [Disabled]

Disables or enables the system wake up by RTC Alarm.

[Enabled] Enables the system to boot up on a scheduled time/ date.

[Disabled] Disables this function.

▶Date (of month) Alarm/ Time (hh:mm:ss) Alarm

Sets RTC alarm date/ Time. If Resume By RTC Alarm is set to [Enabled], the



+ and - keys to select the date & time settings).

▶Resume By PCI-E Device [Disabled]

Enables or disables the wake up function of installed PCI-E expansion cards,

integrated LAN controllers or USB devices which are supported by third party

integrated chips.

[Enabled] Enables the system to be awakened from the power saving modes

when activity or input signal of PCIe device is detected.

[Disabled] Disables this function.

▶Resume by USB Device [Disabled]

Disables or enables system wake up from S3/S4 by USB device.

[Enabled] Enables the system to be awakened from sleep state when activity of

USB device is detected.

[Disabled] Disables this function.

56 BIOS Setup

▶Resume From S3/S4/S5 by PS/2 Mouse [Disabled]

Enables or disables the system wake up by PS/2 mouse.

[Enabled] Enables the system to be awakened from S3/ S4/ S5 state when

activity of PS/2 mouse is detected.

[Disabled] Disables this function.

▶Resume From S3/S4/S5 by PS/2 Keyboard [Disabled]

Enables or disables the system wake up by PS/2 keyboard.

[Any Key] Enables the system to be awakened from S3/ S4/ S5 state when

activity of any key on PS/2 keyboard is detected.

[Hot Key] Enables the system to be awakened from S3/ S4/ S5 state when

activity of hot key on PS/2 keyboard is detected.

[Disabled] Disables this function.

▶Hot Key [Ctrl+Space]

Selects a combination of keys as a hot key to wake the system. This item appears

when you set the Resume From S3/S4/S5 by PS/2 Keyboard to Hot Key.

▶Secure Erase+

Enables or disables Secure Erase+ function. Secure Erase+ is the best way to

effectively wipe all data from a SSD. Please note that data of SSD will be erased after

enabling Secure Erase+.

▶Realtek (R) 8111 Gigabit

Shows driver information and configuration of the Ethernet controller parameter.

Boot

Sets the sequence of system boot devices.

▶Full Screen Logo Display [Enabled]

Enables or disables to show the full screen logo while system POST.

[Enabled] Shows the logo in full screen.

[Disabled] Shows the POST messages.

▶Bootup NumLock State [On]

Select the keyboard NumLock state upon bootup.

▶ Info Block e󽙋ect [Unlock]

Sets the state of Help information block.

[Unlock] Sliding effect.

[Lock] Fix the Help information block on the screen.

▶POST Beep [Disabled]

Enables or disables the POST beep.

BIOS Setup

▶Boot Mode Select [LEGACY+UEFI]

Sets the system boot mode from legacy or UEFI architecture depending on OS

installation requirement. This item will become un-selectable and will be configured

automatically by BIOS when BIOS UEFI/CSM Mode sets to UEFI.

[UEFI] Enables UEFI BIOS boot mode support only.

[LEGACY+UEFI] Enables both Legacy BIOS boot mode and UEFI BIOS boot

mode.

▶FIXED BOOT ORDER Priorities

Sets device priority for system boot.

▶Boot Option Priorities

These items are used to prioritize the installed boot devices.

Security

▶Administrator Password

Sets administrator password for system security. User has full rights to change the

BIOS items with administrator password. After setting the administrator password,

the state of this item will show Installed.

▶User Password

Sets User Password for system security. User has limited rights to change the BIOS

items with user password. This item will be available when administrator password is

set. After setting the user password, the state of this item will show Installed.

▶Password Check [Setup]

Selects a condition that will request the password.

[Setup] A password will be requested for entering the BIOS Setup.

[Boot] A password will be requested for booting the system.

▶Password Clear [Enabled]

Enables or disables the clear CMOS behavior to clear a set password.

[Enabled] The password will be erased after clear CMOS.

[Disabled] The password will always be kept.

⚠

Important

When selecting the Administrator / User Password items, a password box will appear

on the screen. Type the password then press Enter. The password typed now will

replace any previous set password from CMOS memory. You will be prompted to

confirm the password. You may also press Esc key to abort the selection.

To clear a set password, press Enter when you are prompted to enter a new

password. A message will confirm the password is being disabled. Once the password

is disabled, you can enter the setup and OS without authorization.

58 BIOS Setup

▶Trusted Computing

Sets TPM (Trusted Platform Module) function.

▶Security Device Support [Disabled]

Enables or disables the TPM function to build the endorsement key for accessing

the system.

▶AMD fTPM switch [AMD CPU fTPM]

Selects TPM device. This item will appear when Security Device Support is

enabled.

[AMD CPU fTPM] Select it for AMD Firmware TPM.

[AMD CPU fTPM Disabled] Select it for Discrete TPM.

▶Device Select [Auto]

Sets the version of the TPM device. The version must be identical with the device.

Sets to Auto, system will detect the TPM 2.0 or TPM 1.2 model automatically.

▶ Chassis Intrusion Conguration

Press Enter to enter the sub-menu.

▶Chassis Intrusion [Disabled]

Enables or disables recording messages while the chassis is opened. This function

is ready for the chassis equips a chassis intrusion switch.

[Enabled] Once the chassis is opened, the system will record and issue a

warning message.

[Reset] Clear the warning message. After clearing the message, please

return to Enabled or Disabled.

[Disabled] Disables this funcion.

Save & Exit

▶Discard Changes and Exit

Exit BIOS setup without saving any change.

▶Save Changes and Reboot

Save all changes and reboot the system.

▶Save Changes

Save current changes.

▶Discard Changes

Discard all changes and restore to the previous values.

▶Restore Defaults

Restore or load all default values.

▶Boot Override

The installed boot-able devices will appear on this menu, you can select one of them

to be the boot device.

BIOS Setup

⚠

Important

∙

Overclocking your PC manually is only recommended for advanced users.

∙

Overclocking is not guaranteed, and if done improperly, it could void your warranty

or severely damage your hardware.

∙

If you are unfamiliar with overclocking, we advise you to use GAME BOOST function

for easy overclocking.

∙

The BIOS items in OC menu will vary with the processor.

▶OC Explore Mode [Normal]

Enables or disables to show the normal or expert version of OC settings.

[Normal] Provides the regular OC settings in BIOS setup.

[Expert] Provides the advanced OC settings for OC expert to configure in BIOS

setup.

Note: We use * as the symbol for the OC settings of Expert mode.

▶CPU Ratio [Auto]

Sets the CPU ratio that is used to determine CPU clock speed. This item can only be

changed if the processor supports this function.

▶ Advanced CPU Conguration

Press Enter to enter the sub-menu. User can set the parameters about CPU

power/ current. The system may become unstable or unbootable after changing the

parameters. If it occurs, please clear the CMOS data and restore the default settings.

▶FCH Base Clock (MHz) [Auto]

󽚛󽚜

Auto, the BIOS will automatically set the clock or you can set it manually.

▶A-XMP [Disabled]

Please enable A-XMP or select a profile of memory module for overclocking the

memory. This item will be available when the installed processor, memory modules

and motherboard support this function.

60 BIOS Setup

▶DRAM Frequency [Auto]

Sets the DRAM frequency. Please note the overclocking behavior is not guaranteed.

▶Adjusted DRAM Frequency

Shows the adjusted DRAM frequency. Read-only.

▶FCLK Frequency [Auto]

Sets FCLK frequency. Lower FCLK frequency may help you to set higher base clock

frequency.

▶UCLK DIV1 Mode [Auto]

Sets UCLK (Internal memory controller clock) mode.

▶Load Memory Presets [Disabled]*

Load OC Memory Preset will optimize the timing, voltage of installed memory module.

⚠

Important

Manual tweaking or fine-tune preferred parameter is still recommended due to

different memory module manufacturing quality.

▶Memory Try It ! [Disabled]

It can improve memory compatibility or performance by choosing optimized memory

preset.

▶Memory Failure Retry

Enables or disables system to reboot with default settings when memory OC failed.

▶ Advanced DRAM Conguration

Press Enter to enter the sub-menu. User can set the memory timing for each/ all

memory channel. The system may become unstable or unbootable after changing

memory timing. If it occurs, please clear the CMOS data and restore the default

settings. (Refer to the Clear CMOS jumper section to clear the CMOS data, and enter

the BIOS to load the default settings.)

▶CPU Voltages control [Auto]

These options allows you to set the voltages related to CPU. If set to Auto, BIOS will

set these voltages automatically or you can set it manually.

▶DRAM Voltages control [Auto]

These options allows you to set the voltages related to memory. If set to Auto, BIOS

will set these voltages automatically or you can set it manually.

BIOS Setup

▶Memory Changed Detect [Enabled]*

Enables or disables the system to issue a warning message during boot when the

memory has been replaced.

[Enabled] The system will issue a warning message during boot and then you have

to load the default settings for new devices.

[Disabled] Disables this function and keeps the current BIOS settings.

▶ CPU Specications

Press Enter to enter the sub-menu. This sub-menu displays the information of

installed CPU. You can also access this information menu at any time by pressing [F4].

Read only.

▶CPU Technology Support

Press Enter to enter the sub-menu. The sub-menu shows the key features of

installed CPU. Read only.

▶MEMORY-Z

Press Enter to enter the sub-menu. This sub-menu displays all the settings and

timings of installed memory. You can also access this information menu at any time by

pressing [F5].

▶DIMMx Memory SPD

Press Enter to enter the sub-menu. The sub-menu displays the information of

installed memory. Read only.

▶CPU Features

Press Enter to enter the sub-menu.

▶Simultaneous Multi-Threading [Enabled] (optional)

Enables/ disables the AMD Simultaneous Multi-Threading. This item appears when

the installed CPU supports this technology.

▶Global C-state Control [Enabled] (optional)

Enables/ disables IO based C-state generation and DF C-states.

▶Opcache Control [Auto] (optional)

Enables/ disables Opcache. Opcache stores recent decode instruction to save

the decoding time when the instruction is repeated. And it may increase the CPU

performance and reduce the power consumption slightly.

▶IOMMU Mode (optional)

Enables/disables the IOMMU (I/O Memory Management Unit) for I/O Virtualization.

62 BIOS Setup

▶Spread Spectrum (optional)

This function reduces the EMI (Electromagnetic Interference) generated by

modulating clock generator pulses.

[Enabled] Enables the spread spectrum function to reduce the EMI

(Electromagnetic Interference) problem.

[Disabled] Enhances the overclocking ability of CPU Base clock.

⚠

Important

∙

If you do not have any EMI problem, leave the setting at [Disabled] for optimal

system stability and performance. But if you are plagued by EMI, select the value of

Spread Spectrum for EMI reduction.

∙

The greater the Spread Spectrum value is, the greater the EMI is reduced, and the

system will become less stable. For the most suitable Spread Spectrum value, please

consult your local EMI regulation.

∙

Remember to disable Spread Spectrum if you are overclocking because even a

slight jitter can introduce a temporary boost in clock speed which may just cause your

overclocked processor to lock up.

▶Relaxed EDC throttling [Auto] (optional)

Relaxed EDC throttling reduces the amount of time the processor will throttle the

cores.

[Auto] AMD's recommendation

[Enabled] Reduce the amount of time the processor will throttle.

 

▶AMD Cool’n’Quiet [Enabled]

󽙋

power consumption.

▶SVM Mode [Enabled]

Enables/ disables the AMD SVM (Secure Virtual Machine) Mode.

▶BIOS PSP Support [Enabled] (optional)

Enables/ disables the BIOS PSP support. It manages PSP sub-items including all

C2P/P2C mailbox, Secure S3, fTPM support.

▶Power Supply Idle Control [Auto] (optional)

It allows you to select the power-saving control mode for the CPU when all cores

are in a non-CO state. If set to Auto

BIOS Setup

M-FLASH

M-FLASH provides the way to update BIOS with a USB flash drive. Please download

the latest BIOS file that matches your motherboard model from MSI website, save the

BIOS file into your USB flash drive. And then follow the steps below to update BIOS.

1. Insert the USB flash drive that contains the update file into the computer.

2. Click on M-FLASH tab, a demand message will be prompted. Click on Yes to

reboot and enter the flash mode.

3. The system will enter the flash mode and a file selection menu will appear after

rebooting.

4. Select a BIOS file to perform the BIOS update process.

5. After the flashing process is 100% completed, the system will reboot

automatically.

64 BIOS Setup

OC PROFILE

▶ Overclocking Prole 1/ 2/ 3/ 4/ 5/ 6

Overclocking Profile 1/ 2/ 3/ 4/ 5/ 6 management. Press Enter to enter the sub-menu.

▶Set Name for Overclocking Profile 1/ 2/ 3/ 4/ 5/ 6



▶Save Overclocking Profile 1/ 2/ 3/ 4/ 5/ 6



▶Load Overclocking Profile 1/ 2/ 3/ 4/ 5/ 6



▶Clear Overclocking Profile 1/ 2/ 3/ 4/ 5/ 6



▶ OC Prole Load from ROM

Load OC profile from BIOS ROM.

▶ OC Prole Save to USB

Save OC profile to the USB flash drive. The USB flash drive should be FAT/ FAT32

format only.

▶ OC Prole Load from USB

Load OC profile from the USB flash drive. The USB flash drive should be FAT/ FAT32

format only.

BIOS Setup

HARDWARE MONITOR

Temperature

& Speed

Fan Manage

Temperature/

Voltage display

Setting

Buttons

▶Temperature & Speed

Shows the current CPU temperature, system temperature and fans' speeds.

▶Fan Manage

▪PWM - allows you to select the PWM mode for fan operation.

▪DC - allows you to select the DC mode for fan operation.

▪Fan step up/ down time - allows you to set the period of fan step up/ down.

▪Smart Fan Mode field - allows you to drag the gradient points to configure

the fan target values for Smart Fan mode. Smart Fan can control the fan speed

automatically depending on the CPU temperature to keep it with in a specific

range. If the current CPU temperature reaches to the target value, the Smart Fan

function will be activated.

⚠

Important

∙

The changing will achieve after you save the changes and reboot the system.

∙

Make sure fans are working properly after switching the PWM/ DC mode.

▶Settings Buttons

▪All Full Speed - configures all fans to run at full operating speed.

▪All Set Default - configures all fans to run at default operating speed.

▪All Set Cancel - discards current changes and restores previous operating fan

speeds .

▶Temperature/ Voltage display

Shows CPU/ system temperature and the current voltages of CPU, system and

memory.

66 AMD RAID Configuration

AMD RAID Configuration

The following are the RAID levels supported by RAIDXpert2.

RAID 0 (Striping) breaks the data into blocks which are written to separate hard

drives. Spreading the hard drive I/O load across independent channels

greatly improves I/O performance.

RAID 1 (Mirroring) provides data redundancy by mirroring data between the hard

drives and provides enhanced read performance.

RAID 10 (Striped RAID1 Sets) uses four hard drives to create a combination of RAID 0

and 1 by forming a RAID 0 array from two RAID 1 arrays.

Volume (JBOD) provides the ability to link-together storage from one or several

disks, regardless of the size of the space on those disks. Useful in

scavenging space on disks unused by other disks in the array. Does not

provide performance benefits or data redundancy.

RAIDABLE (also known as RAID Ready) allows the user to add more storage space or

create a redundant array after a system is installed.

RAID level comparison

RAID 0 RAID 1 RAID 10

Minimum # drives 2 2 4

Data protection None Excellent Excellent

Read performance Excellent OK OK

Write performance Excellent Good Good

Capacity utilization 100% 50% 50%

⚠

Important

All the information/ volumes/ pictures listed in your system might differ from the

illustrations in this appendix.

Enabling RAIDXpert2 Configuration Utility

To enter the RAIDXpert2 Configuration Utility menu

1. Power on and press Delete key to enter BIOS Setup menu.

2. Press F7 to switch to Advanced mode from EZ mode.

3. Go to BIOS > SETTINGS > Advanced > Integrated Peripherals > SATA Mode and

change setting to RAID Mode.

4. Go to BIOS > SETTINGS > Advanced > Windows OS Configuration > BIOS UEFI/

CSM Mode and change setting to UEFI.

5. Press F10 to save configuration and exit, and then reboot and press Delete key to

enter BIOS Setup menu.

6. Go to BIOS > SETTINGS > Advanced > RAIDXpert2 Configuration Utility sub-

menu.

AMD RAID Configuration

Initializing Disks

New disks and legacy disks must be initialized before they can be used to create an

AMD-RAID array. Initialization writes AMD-RAID configuration information (metadata)

to a disk.

⚠

Important

∙

If a disk is part of an AMD-RAID array, the disk cannot be selected for initialization.

To initial the disk anyway, delete the AMD-RAID array. Data on the disk is deleted

during initialization so ensure the correct disks are chosen to initialize.

∙

A legacy disk can contain valid data. When a legacy disk is initialized, all data on the

disk is lost.

To initialize disks

1. As previously mentioned, enable RAIDXpert2 Configuration Utility.

2. Go to BIOS > SETTINGS > Advanced > RAIDXpert2 Configuration Utility > Physical

Disk Management > Select Physical Disk Operations > Initialize Disk sub-menu.

3. Select desired disks by changing the Physical Disk setting to Enabled.

4. Select OK, then press Enter.

5. Review the warning message, if you want to proceed, select YES, then press Enter.

6. Initialization takes 10 to 15 seconds per disk. During initialization, a complete

rescan of all channels is done automatically.

68 AMD RAID Configuration

Creating Arrays

Arrays can be created after the disks are initialized.

⚠

Important

∙

For redundant arrays, the Create process is not started until after the operating

system and AMD-RAID OS drivers have been installed and the system has booted to

the operating system. However, the arrays are immediately available to use for either

a bootable array or a data array.

∙

Array numbers are valid only for a given boot and might be different in the

RAIDXpert2 Configuration Utility and RAIDXpert2. If a permanent label is required, use

the RAIDXpert2 Web GUI Array Naming feature.

∙

At any point in the procedure, return to a prior window by pressing ESC.

∙

If the system is booted from an AMD-RAID bootable array, the first array in the

Arrays section must be the bootable array. The system boots only from the first array

in the Arrays section.

To create an array

1. As previously mentioned, enable RAIDXpert2 Configuration Utility.

2. Go to BIOS > SETTINGS > Advanced > RAIDXpert2 Configuration Utility > Array

Management > Create Array sub-menu.

3. Select the RAID level from the Select RAID Level drop down menu.

4. Enter Select Physical Disks sub-menu, select member disks by changing the

Physical Disk setting to Enabled.

5. Select Apply Changes, then press Enter to apply and go back to previous sub-

menu.

6. Change the Select CacheTagSize, Read Cache Policy and Write Cache Policy

settings according to your needs.

7. Select Create Array, then press Enter.

AMD RAID Configuration

Deleting Arrays

⚠

Important

∙

Deleting an array permanently destroys all data that is on the array. This action

cannot be undone and it is very unlikely that the data can be recovered.

∙

Do not delete the first array listed in the Arrays section, if it is the AMD-RAID

bootable array. Doing this deletes the operating system and AMD-RAID files.

To delete an array

1. As previously mentioned, enable RAIDXpert2 Configuration Utility.

2. Go to BIOS > SETTINGS > Advanced > RAIDXpert2 Configuration Utility > Array

Management > Delete Array sub-menu.

3. Select the desired array and change the setting to Enabled.

4. Enter Delete Array(s) sub-menu.

5. Review the warning message, if you want to proceed, Select Confirm and change

the setting to Enabled.

6. Select YES then press Enter.

70 AMD RAID Configuration

Installing RAID Driver

New Operating System Installation

The following details the installation of the drivers while installing operating system.

1. During the operating system installation, after selecting the location to install

Windows click on Load driver button to install a third party RAID driver.

2. When prompted, insert the USB flash drive with AMD RAID Drivers and then click

Browse.

▪To make an AMD RAID Drivers USB flash drive. Insert the MSI Driver Disc into

the optical drive. Copy all the contents in \\Storage\AMD\

3. Navigate to the directory containing the saved AMD RAID drivers, then click OK.

4. Select the (rcbottom.inf) driver, click Next.

5. When prompted, click OK.

6. Click Browse and navigate to the directory containing the saved AMD RAID drivers

again, then click OK.

7. Select the (rcraid.inf) driver, click Next.

8. You have successfully installed the RAID driver, and Windows setup should

continue.

9. Leave the disk/ USB drive in the computer until the system reboots itself.

Windows setup will need to copy the files after the RAID volume is formatted, and

Windows setup starts copying files.

AMD RAIDXpert2 Management Suite Installation

1. Set the SATA Mode to RAID Mode in BIOS

2. Insert the MSI Driver Disc into the optical drive.

3. Click the Select to choose what happens with this disc pop-up notification, then

select Run DVDSetup.exe to open the installer. If you turn off the AutoPlay feature

from the Windows Control Panel, you can still manually execute the DVDSetup.

exe from the root path of the MSI Driver Disc.

4. Under the Drivers/Software tab, check the AMD RAID Drivers check-box.

5. Click the Install button.

6. When prompt you to restart, click OK button to finish.

7. Restart your computer and enter the Windows operating system.

8. Double-click the RAIDXpert2 icon to open the RAIDXpert2 Web GUI.

▪Default credentials are:

▫Username - admin

▫Password - admin

9. Change the credentials:

▪Create new username and password

10. Re-log into the RAIDXpert2 Web GUI with the new credentials.

Troubleshooting

Before sending the motherboard for RMA

repair, try to go over troubleshooting

guide first to see if your got similar

symptoms as mentioned below.

The power is not on.

∙Connect the AC power cord to an

electrical outlet securely.

∙Check if all ATX power connectors

like ATX_PWR1, CPU_PWR1~2 are

connected from the power supply to the

motherboard?

∙Some power supply units have a power

button on the rear side, make sure the

button is turned on.

∙Check if the power switch cable is

connected to JFP1 pin header properly.

∙Verify the Clear CMOS jumper JBAT1 is

set to Keep DATA.

∙Test with another known working

power supply of equal or greater

wattage.

The power is on, but no signal to

monitor

∙Connect the monitor power cord to a

electrical outlet securely.

∙Make sure the monitor is turned on.

∙Select different inputs on the monitor.

∙If 3 long beeps are heard, remove all

memory modules and try to install only

one memory module in the DIMMA2 slot

first and then restart the computer.

∙If 1 long 2 short beeps are heard,

remove and reinstall the graphics card

and then restart the computer.

∙Test with another known working

graphics card.

The computer does not boot after

updating the BIOS

∙Clear the CMOS.

∙Use the secondary BIOS to bootup the

system (Only for motherboard with Dual

BIOS)

Lost BIOS password

∙Clear the CMOS, but that will cause

you to lose all customized settings in the

BIOS.

There is no audio

∙Adjust the volume.

∙Connect the speakers/headphones to

audio ports on the motherboard rear IO

panel.

∙Remove secondary speakers/

headphones, HDMI cables, USB audio

devices.

∙Test with another known working

speaker or headphone.

There is no network

∙Make sure the network chipset driver

has been installed.

∙Verify if the network cable is properly

connected and make sure the LAN port

LEDs are properly illuminated.

∙Verify your TCP/IP settings.

∙Restart or reset your router.

∙Test with another known working LAN

cable.

The USB device is not working

∙Make sure your USB drive driver has

been installed.

∙Verify if USB device is listed in

Windows® Device Manager.

∙Connect the USB device to other USB

port on the motherboard rear IO panel.

72 Regulatory Notices

Regulatory Notices

FCC Compliance Statement

Note: This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV

technician for help.

Caution: Changes or modifications not expressly

approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

Tested to comply with FCC standards

FOR HOME OR OFFICE USE

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation.

CE Conformity

Products bearing the CE marking comply

with one or more of the following EU

Directives as may be applicable:

RED 2014/53/EU; Low Voltage Directive 2014/35/EU;

EMC Directive 2014/30/EU; RoHS Directive 2011/65/EU.

Compliance with these directives is assessed using

applicable European Harmonized Standards.

The point of contact for regulatory matters is MSI,

MSI-NL Eindhoven 5706 5692 ER Son.

B급 기기 (가정용 방송통신기자재)

󼕦󺰢󺰢󻂆󺧲󼘇󼒛󺯻󼗶󼖂󽃾󼗳󽍛󺰢󺰢󻙎󻼎󼛮

󻙎󺧲󼘇󼏂󻼎󻺞󼒛󽍊󻂆󺩵󼔶󻢛󼗳󼔮󻙎󽍊󻡢󻢚

󻋒󼞲󼏟󼏂󻼎󻺞󼒛󽍒󼀊󼕺󼂧󻂺󻃖

クラスB情報技術装置

󸅗󶹌󾖛󽚵󳞹󲝅󳫒󸂓󸅗󶹌󾖜

󸅗󶹌󾖛󲺟󳐑󵩫󲟓󱣎󵭡󵺅󵷜

   󾖛  󸅗 󶹌            󲀰

󱥰󴡉󸶀󳲞󱣎󵭡󾖛󲀰󱥰󹦟󲺗󳓜󸦕

󾖜󲀮󾉣󸔆󴃬󴉩󳗂

󴨟󲀮󾉣󱚘

VCCI-B

C-Tick Compliance

Battery Information

European Union:

Batteries, battery packs, and

accumulators should not be disposed of as

unsorted household waste. Please use the

public collection system to return, recycle,

or treat them in compliance with the local

regulations.

Taiwan:

󳑿󹩚󴯶󸕂󲔴󳽴

For better environmental protection,

waste batteries should be collected

separately for recycling or special

disposal.

California, USA:

The button cell battery may contain

perchlorate material and requires special

handling when recycled or disposed of in

California.

For further information please visit:

http://www.dtsc.ca.gov/hazardouswaste/perchlorate/

CAUTION: There is a risk of explosion, if battery is

incorrectly replaced.

Replace only with the same or equivalent type

recommended by the manufacturer.

Chemical Substances Information

In compliance with chemical substances regulations,

such as the EU REACH Regulation (Regulation EC

No. 1907/2006 of the European Parliament and the

Council), MSI provides the information of chemical

substances in products at:

http://www.msi.com/html/popup/csr/evmtprtt_pcm.

html

Environmental Policy

• The product has been designed to

enable proper reuse of parts and

recycling and should not be thrown

away at its end of life.

• Users should contact the local

authorized point of collection for recycling and

disposing of their end-of-life products.

• Visit the MSI website and locate a nearby distributor

for further recycling information.

• Users may also reach us at gpcontdev@msi.com for

information regarding proper Disposal, Take-back,

Recycling, and Disassembly of MSI products.

WEEE (Waste Electrical and

Electronic Equipment) Statement

ENGLISH

To protect the global environment and as

an environmentalist, MSI must remind

you that...

Under the European Union (“EU”) Directive

on Waste Electrical and Electronic

Equipment, Directive 2002/96/EC, which

takes effect on August 13, 2005, products of “electrical

Regulatory Notices

and electronic equipment” cannot be discarded as

municipal wastes anymore, and manufacturers of

covered electronic equipment will be obligated to take

back such products at the end of their useful life. MSI

will comply with the product take back requirements

at the end of life of MSI-branded products that are sold

into the EU. You can return these products to local

collection points.

DEUTSCH

Hinweis von MSI zur Erhaltung und Schutz unserer

Umwelt

Gemäß der Richtlinie 2002/96/EG über Elektro- und

Elektronik-Altgeräte dürfen Elektro- und Elektronik-

Altgeräte nicht mehr als kommunale Abfälle entsorgt

werden. MSI hat europaweit verschiedene Sammel-

und Recyclingunternehmen beauftragt, die in die

Europäische Union in Verkehr gebrachten Produkte,

am Ende seines Lebenszyklus zurückzunehmen.

Bitte entsorgen Sie dieses Produkt zum gegebenen

Zeitpunkt ausschliesslich an einer lokalen

Altgerätesammelstelle in Ihrer Nähe.

FRANÇAIS

En tant qu’écologiste et afin de protéger

l’environnement, MSI tient à rappeler ceci...

Au sujet de la directive européenne (EU) relative aux

déchets des équipement électriques et électroniques,

directive 2002/96/EC, prenant effet le 13 août 2005, que

les produits électriques et électroniques ne peuvent

être déposés dans les décharges ou tout simplement

mis à la poubelle. Les fabricants de ces équipements

seront obligés de récupérer certains produits en fin

de vie. MSI prendra en compte cette exigence relative

au retour des produits en fin de vie au sein de la

communauté européenne. Par conséquent vous pouvez

retourner localement ces matériels dans les points

de collecte.

РУССКИЙ







































ESPAÑOL

MSI como empresa comprometida con la protección

del medio ambiente, recomienda:

Bajo la directiva 2002/96/EC de la Unión Europea

en materia de desechos y/o equipos electrónicos,

con fecha de rigor desde el 13 de agosto de 2005,

los productos clasificados como “eléctricos y

equipos electrónicos” no pueden ser depositados

en los contenedores habituales de su municipio, los

fabricantes de equipos electrónicos, están obligados

a hacerse cargo de dichos productos al termino de

su período de vida. MSI estará comprometido con los

términos de recogida de sus productos vendidos en

la Unión Europea al final de su periodo de vida. Usted

debe depositar estos productos en el punto limpio

establecido por el ayuntamiento de su localidad o

entregar a una empresa autorizada para la recogida de

estos residuos.

NEDERLANDS

Om het milieu te beschermen, wil MSI u eraan

herinneren dat….

De richtlijn van de Europese Unie (EU) met betrekking

tot Vervuiling van Electrische en Electronische

producten (2002/96/EC), die op 13 Augustus 2005 in

zal gaan kunnen niet meer beschouwd worden als

vervuiling. Fabrikanten van dit soort producten worden

verplicht om producten retour te nemen aan het

eind van hun levenscyclus. MSI zal overeenkomstig

de richtlijn handelen voor de producten die de

merknaam MSI dragen en verkocht zijn in de EU. Deze

goederen kunnen geretourneerd worden op lokale

inzamelingspunten.

SRPSKI





vas podesti da…





EC, koja stupa na snagu od 13. Avgusta 2005, proizvodi











proizvoda kojima je istekao vek trajanja, koji imaju MSI



vratiti na lokalnim mestima za prikupljanje.

POLSKI







odpadów produktów elektrycznych i elektronicznych















(sprzedawane na terenie Unii Europejskiej) wycofywane



wyznaczonych punktach zbiorczych.

TÜRKÇE



























74 Regulatory Notices

ČESKY









EC platné od 13. srpna 2005 je zakázáno likvidovat



komunálním odpadu a výrobci elektronických













MAGYAR

Annak érdekében, hogy környezetünket megvédjük,



Önt, hogy ...

Az Európai Unió („EU”) 2005. augusztus 13-án hatályba



hulladékairól szóló 2002/96/EK irányelve szerint

az elektromos és elektronikus berendezések



és az ilyen elektronikus berendezések gyártói

kötelessé válnak az ilyen termékek visszavételére

azok hasznos élettartama végén. Az MSI betartja a

termékvisszavétellel kapcsolatos követelményeket

az MSI márkanév alatt az EU-n belül értékesített

termékek esetében, azok élettartamának végén. Az



ITALIANO

Per proteggere l’ambiente, MSI, da sempre amica della

natura, ti ricorda che….

In base alla Direttiva dell’Unione Europea (EU) sullo

Smaltimento dei Materiali Elettrici ed Elettronici,

Direttiva 2002/96/EC in vigore dal 13 Agosto 2005,

prodotti appartenenti alla categoria dei Materiali

Elettrici ed Elettronici non possono più essere eliminati

come rifiuti municipali: i produttori di detti materiali

saranno obbligati a ritirare ogni prodotto alla fine

del suo ciclo di vita. MSI si adeguerà a tale Direttiva

ritirando tutti i prodotti marchiati MSI che sono stati

venduti all’interno dell’Unione Europea alla fine del

loro ciclo di vita. È possibile portare i prodotti nel più

vicino punto di raccolta

日本JIS C 0950材質宣言

󴂬󴋉󳋌󴚄󸋮󴑸󾖛󳎧󴊆󴂬󱟧󹤒󸡯

󲢔󵛚󲹥󱴹󹆣󹩚󴮅󹩚󲷍󴡉󲑠󾖛󸇆󸹈

󶽳󲂳󴊈󵛃󸣚󸂱󶈾󶺳󱺅󱟔󾖜

http://www.msi.com/html/popup/csr/cemm_jp.html

http://tw.msi.com/html/popup/csr_tw/cemm_jp.html

India RoHS

This product complies with the “India E-waste

(Management and Handling) Rule 2011” and prohibits

use of lead, mercury, hexavalent chromium,

polybrominated biphenyls or polybrominated diphenyl

ethers in concentrations exceeding 0.1 weight % and

0.01 weight % for cadmium, except for the exemptions

set in Schedule 2 of the Rule.

Türkiye EEE yönetmeliği



Україна обмеження на наявність

небезпечних речовин











Việt Nam RoHS











Wireless Radio Use

This device is restricted to indoor use when operating

in the 2.4GHz, 5GHz frequency band.

Cet appareil doit être utilisé à l’intérieur.

󻃫󽍦󻤦󻼒󻼖󻰶󻂆󼒦󼒛󼜃󼗶󽃾󽐮󼃒󺧲󻂗󻼣󼕦󼕺󼔾

󸇆󲆛󾖛󲄔󴲾󳿌󳌶󲚺󱹿󱢖

󾖛󲾯󱱟󱣎󵭡󲁗󷅯󾖜

NCC無線設備警告聲明

󳋌󱢖󹲡󵢋󸒎󹲡󴫓󹤗󴁘󲹸󱰭󱣎󵭡󾖜

󶬈󲘻󳓑󸓆󸙒󲁺󴑸󱛷󱢀󱸪󵢋󲼽󹲡󹩚󴡉󾖞󹬰󶬈󸐎󲁗󾖞󱰻󲁤󾖛󲉦

󷵏󳨘󱣎󵭡󶽳󲗗󱚚󳗈󳺖󷍬󸛚󴉣󹲡󵢋󾖛󱸬󲣴󱸪󵢋󳨘󸛚󴉣󱿖󸐈

󸎽󱛷󵛚󳚱󲀟󱸪󷅯󾖜

󱢀󱸪󵢋󲼽󹲡󹩚󴡉󱛷󱣎󵭡󱚚󳗈󳖋󹱄󹶗󷏹󲹂󾆈󲀟󳎥󳼄󲁺󴲥󸸶

󱥰󽚮󶬈󵷒󵤱󴊈󳎥󳼄󵤱󸟱󴄼󾖞󳦔󶕌󱾔󱩆󵭡󾖞󱚿󳽺󲋉󷍿󵐦󳎥󳼄󴄼

󴁔󳗈󶳶󶴙󱣎󵭡󾖜󱶝󹱎󲁺󴲥󸸶󱥰󾖞󳮜󱤀󹩚󱥰󴲥󸋮󲹥󱢖󴚄󱛷󵐦

󶮥󹩚󸸶󱥰󾖜󱢀󱸪󵢋󲼽󹲡󹩚󴡉󹱑󳘢󲀰󲁺󴲥󸸶󱥰󳨘󳋌󴚄󾖛󶍔󲸜

󲀟󹅘󵵢󵭡󹩚󴲾󸱺󲼽󳚱󹩚󴡉󸐈󱪸󱛷󳎥󳼄󾖜

Products with radio functionality (EMF)

This product incorporates a radio transmitting

and receiving device. For computers in normal

use, a separation distance of 20 cm ensures that

radio frequency exposure levels comply with EU

requirements. Products designed to be operated

at closer proximities, such as tablet computers,

comply with applicable EU requirements in typical

operating positions. Products can be operated without

maintaining a separation distance unless otherwise

indicated in instructions specific to the product.

Restrictions for products with radio functionality

CAUTION: IEEE 802.11x wireless LAN with

5.15–5.35 GHz frequency band is restricted

for indoor use only in all European Union

member states, EFTA (Iceland, Norway,

Liechtenstein), and most other European countries

(e.g., Switzerland, Turkey, Republic of Serbia).

Using this WLAN application outdoors might lead to

interference issues with existing radio services.

Radio frequency bands and maximum power levels

Features :802.11 a/b/g/n/ac, BT

Frequency Range :2.4GHz, 5GHz

Modulation :FHSS, DSSS, OFDM

Power Output :10, 20, 23

Channel Band Width :1, 5, 20 ,40 , 80MHz

Regulatory Notices

Micro-Star Int’l Co.,Ltd.

The MSI logo used is a registered trademark of

Micro-Star Int’l Co., Ltd. All other marks and names

mentioned may be trademarks of their respective

owners. No warranty as to accuracy or completeness is

expressed or implied. MSI reserves the right to make

changes to this document without prior notice.

Revision History

Version 1.0, 2020/03, First release.

Technical Support

If a problem arises with your system and no solution

can be obtained from the user guide, please

contact your place of purchase or local distributor.

Alternatively, please try the following help resources

for further guidance.

• Visit the MSI website for technical guide, BIOS

updates, driver updates, and other information:

http://www.msi.com

• Register your product at: http://register.msi.com

MS-7C84主板产品中有害物质的名称及含量

󸿬󱠁󲂁󶎊

󴊈󲺗󵛃󸤼

󹜱

(Pb)

󴯳

(Hg)

󹞵

(Cd)

󱰽󱠃󹝘

(Cr(VI))

󲣙󴾨󷀐󷖪

(PBB)

󲣙󴾨󱝗󷖪󹄲

(PBDE)

󱾏󱵼󵭳󸩃󴍆󶵪󱠁      

󵭳󴯶      

󲣏󸿬󱥰󲁣󸶚󳲞󲤆      

󶵥󴌂      

󴋉󸂱󴑸󱤀󳰼󵷜󸍂󲹥󶶼󱵺󾖜

󸂱󶈾󸝎󴊈󲺗󵛃󸤼󲖬󸝎󸿬󱠁󳩢󴊈󲗗󸤼󴌂󴀖󱛉󵷜󲂳󹆤󲗗󲖬󸍂󲹥󵷜󹤗󹆤󸋘󴯄󱟧󱚘󾖜

󸂱󶈾󸝎󴊈󲺗󵛃󸤼󷍿󲽕󲖬󸝎󸿬󱠁󵷜󴏉󱚋󲗗󸤼󴌂󴀖󱛉󵷜󲂳󹆤󸦨󱴤󸍂󲹥󵷜󹤗󹆤󸋘󴯄󾖞󱡲󳩢󴊈󸿬󱠁󹀎󶗼󲁺

󴦱󵹩󸋘󴯄󾖜

󱾏󱵼󵭳󸩃󴍆󶵪󱠁󱻏󳭱󱾏󱵼󵭳󸩃󴍆󲀟󱱊󴍐󳨑󵷜󹩏󸿬󱠁󾖜

󵭳󴯶󴋉󱢈󱚗󲦚󴊈󵣄󱥧󱣎󵭡󴊱󹤗󴐟󸜯󾖞󱟧󴋉󱢈󴐟󸜯󱛝󱛞󾖜

󱚗󸷈󴊈󴬐󴊈󲺗󵛃󸤼󳨘󱯯󶨫󴺆󱽤󱠸󱤀󲘻󲁣󱛷󸿬󱠁󳋘󳒺󶾀󴊈󳩢󲠂󱳝󾖜

󵭘󲆛󸿬󱠁󴋉󱢈󱚗󲦚󴊈󵣄󱥧󱣎󵭡󴊱󹤗󴐟󸜯󾖞󱟧󴋉󱢈󴐟󸜯󱛝󱛞󾖜

限用物質含有情況標示聲明書

󸐈󱪷󲂀󶏺󾖠󹩙󷉄󱛞󴡈󴍇 󲘻󷵎󲘻󳓑󾖠

󲌖󱯯

󹤗󵭡󵛃󸣚󲀟󱱊󱻯󲸜󶗼󷵏

󹊰

(Pb)

󴯳

(Hg)

󹔜

(Cd)

󱰽󱭪󹋬

(Cr+6)

󲣙󴾨󷁆󷖪

(PBB)

󲣙󴾨󱝗󷖪󹄲

(PBDE)

󹩚󸩃󴍆      

󹩚󲷍󱯯󱠁      

󹆨󲿦󴡉󴜷󱠁      

󲝺󷋇󴡉󴜷󱠁      

󱪸󶽰󸦨󱴤󲀟󸦨󱴤󱤾󳮜󹤗󵭡󵛃󸣚󱛷󵷔󱴹󴬖󲂳󹆤󸦨󱴤󵷔󱴹󴬖󲂳󹆤󲛫󴽯󱨍󾖜

󱪸󶽰󱤾󳮜󸒎󹱎󹤗󵭡󵛃󸣚󱛷󵷔󱴹󴬖󲂳󹆤󴋆󸦨󱴤󵷔󱴹󴬖󲂳󹆤󲛫󴽯󱨍󾖜

󱪸󶽰󱤾󳮜󸒎󹱎󹤗󵭡󵛃󸣚󵍤󳱺󹤵󹱎󵺅󾖜

Table of Contents

MSI MAG X570 TOMAHAWK WIFI User Manual

Related Manuals