Quick Start
- Preparing Tools and Components
- Safety Information
- Case stand-off notification
- Avoid collision notification
- Installing a Processor
- Installing DDR4 memory
- Connecting the Front Panel Header
- Installing the Motherboard
- Connecting the Power Connectors
- Installing SATA Drives
- Installing a Graphics Card
- Connecting Peripheral Devices
- Power On
Specifications
- JCORSAIR1 Connector Specification
Package contents
Block Diagram
Rear I/O Panel
- LAN Port LED Status Table
- Audio Ports Configuration
- Realtek Audio Console
- Installing Antennas
Overview of Components
- Processor Socket
- DIMM Slots
- PCI_E1~4: PCIe Expansion Slots
- PCIe bandwidth table
- Bandwidth share table
- M2_1~4: M.2 Slots (Key M)
- Installing M.2 XPANDER-Z Gen4 S card
- SATA1~8: SATA 6Gb/s Connectors
- JFP1, JFP2: Front Panel Connectors
- CPU_PWR1~2, ATX_PWR1: Power Connectors
- JOC_FS1: Safe Boot Jumper
- T_SEN1~2: Thermal Sensor Connectors
- W_FLOW1: Water Flow Meter Connector
- JLN1: Low Temperature Booting Jumper
- JAUD1: Front Audio Connector
- JUSB1: USB 3.2 Gen 2 Type-C Connector
- JUSB2~3: USB 3.2 Gen1 Connector
- JUSB4~5: USB 2.0 Connectors
- JTPM1: TPM Module Connector
- CPU_FAN1, PUMP_FAN1, SYS_FAN1~6: Fan Connectors
- JCI1: Chassis Intrusion Connector
- JDASH1 : Tuning Controller connector
- JBAT1: Clear CMOS (Reset BIOS) Jumper
- POWER1, RESET1: Power Button, Reset Button
- JRGB1: RGB LED connector
- JRAINBOW1~2: Addressable RGB LED connectors
- JCORSAIR1: CORSAIR Connector
Onboard LEDs
- EZ Debug LED
- JPWRLED1: LED power input
- LED_SW1: EZ LED Control
- Debug Code LED
- Hexadecimal Character Table
- Boot Phases
- Debug Code LED Table
- ACPI States Codes
Installing OS, Drivers & MSI Center
- Installing Windows® 10
- Installing Drivers
- MSI Center
UEFI BIOS
BIOS Setup
- Entering BIOS Setup
- BIOS User Guide
- Resetting BIOS
- Updating BIOS
Nahimic 3
- Installation and Update
- Audio Tab
- Microphone Tab
- Sound Tracker Tab
- Settings Tab
RAID Configuration
Troubleshooting
CPU_FAN1, PUMP_FAN1, SYS_FAN1~6: Fan Connectors
CPU_PWR1~2, ATX_PWR1: Power Connectors
DIMM Slots
JAUD1: Front Audio Connector
JBAT1: Clear CMOS (Reset BIOS) Jumper
JCI1: Chassis Intrusion Connector
JCORSAIR1: CORSAIR Connector
JDASH1 : Tuning Controller connector
JFP1, JFP2: Front Panel Connectors
JLN1: Low Temperature Booting Jumper
JOC_FS1: Safe Boot Jumper
JPWRLED1: LED power input
JRAINBOW1~2: Addressable RGB LED connectors
JRGB1: RGB LED connector
JTPM1: TPM Module Connector
JUSB1: USB 3.2 Gen 2 Type-C Connector
JUSB2~3: USB 3.2 Gen1 Connector
JUSB4~5: USB 2.0 Connectors
LED_SW1: EZ LED Control
M2_1~4: M.2 Slots (Key M)
PCI_E1~4: PCIe Expansion Slots
POWER1, RESET1: Power Button, Reset Button
Processor Socket
SATA1~8: SATA 6Gb/s Connectors
T_SEN1~2: Thermal Sensor Connectors
W_FLOW1: Water Flow Meter Connector

MSI MEG X570S ACE MAX User Manual

Displayed below is the user manual for MEG X570S ACE MAX by MSI which is a product in the Motherboards category. This manual has pages.

Related Manuals

MSI MAG X570S TOMAHAWK MAX WIFI Manual

MSI MAG X570S TORPEDO MAX Manual

MSI MPG X570S EDGE MAX WIFI Manual

MSI MPG X570S CARBON MAX WIFI Manual

Gigabyte X570S GAMING X (rev. 1.0) Manual

Gigabyte X570S AERO G Manual

Gigabyte X570S AORUS MASTER Manual

Gigabyte X570S AORUS PRO AX Manual

Quick Start

Thank you for purchasing the MSI® MEG X570S ACE MAX motherboard. This Quick

Start section provides demonstration diagrams about how to install your computer.

Some of the installations also provide video demonstrations. Please link to the URL to

watch it with the web browser on your phone or tablet. You may have even link to the

URL by scanning the QR code.

Preparing Tools and Components

DDR4 Memory

Graphics Card

SATA Hard Disk Drive SATA DVD Drive

Phillips Screwdriver

Chassis

Power Supply Unit

A Package of Screws

Thermal Paste

CPU Fan

AMD® AM4 CPU

2Quick Start

Safety Information

∙The components included in this package are prone to damage from electrostatic

discharge (ESD). Please adhere to the following instructions to ensure successful

computer assembly.

∙Ensure that all components are securely connected. Loose connections may cause

the computer to not recognize a component or fail to start.

∙Hold the motherboard by the edges to avoid touching sensitive components.

∙It is recommended to wear an electrostatic discharge (ESD) wrist strap when

handling the motherboard to prevent electrostatic damage. If an ESD wrist strap is

not available, discharge yourself of static electricity by touching another metal object

before handling the motherboard.

∙Store the motherboard in an electrostatic shielding container or on an anti-static

pad whenever the motherboard is not installed.

∙Before turning on the computer, ensure that there are no loose screws or metal

components on the motherboard or anywhere within the computer case.

∙Do not boot the computer before installation is completed. This could cause

permanent damage to the components as well as injury to the user.

∙If you need help during any installation step, please consult a certified computer

technician.

∙Always turn off the power supply and unplug the power cord from the power outlet

before installing or removing any computer component.

∙Keep this user guide for future reference.

∙Keep this motherboard away from humidity.

∙Make sure that your electrical outlet provides the same voltage as is indicated on

the PSU, before connecting the PSU to the electrical outlet.

∙Place the power cord such a way that people can not step on it. Do not place

anything over the power cord.

∙All cautions and warnings on the motherboard should be noted.

∙If any of the following situations arises, get the motherboard checked by service

personnel:

▪Liquid has penetrated into the computer.

▪The motherboard has been exposed to moisture.

▪The motherboard does not work well or you can not get it work according to user

guide.

▪The motherboard has been dropped and damaged.

▪The motherboard has obvious sign of breakage.

∙Do not leave this motherboard in an environment above 60°C (140°F), it may damage

the motherboard.

Quick Start

Case stand-off notification

To prevent damage to the motherboard, any unnecessary mounting stand-off between

the motherboard circuits and the computer case is prohibited. The Case standoff keep

out zone signs will be marked on the backside of motherboard (as shown below) to

serve as a warning to user.

Avoid collision notification

Protective paint is printed around each screw hole to prevent parts from being

scratched.

4Quick Start

Installing a Processor

https://youtu.be/Xv89nhFk1vc

Quick Start

⚠

Important

If you are installing the screw-type CPU heatsink, please follow the figure below to

remove the retention module first and then install the heatsink.

6Quick Start

Installing DDR4 memory

http://youtu.be/T03aDrJPyQs

⚽

DIMMA2 DIMMA2

DIMMB2

DIMMA1

DIMMA2

DIMMB1

DIMMB2

Quick Start

HDD LED

RESET SW

Connecting the Front Panel Header

http://youtu.be/DPELIdVNZUI

JFP1

HDD LED HDD LED -

HDD LED +

POWER LED -

POWER LED +

POWER LED

2 10

+- --

Power LED

HDD LED Reset Switch

Reserved

Power Switch

JFP1

1 HDD LED + 2 Power LED +

3 HDD LED - 4 Power LED -

5 Reset Switch 6 Power Switch

7 Reset Switch 8 Power Switch

9 Reserved 10 No Pin

RESET SW

POWER SW

POWER LED+

POWER LED-

HDD LED

⚽

8Quick Start

BAT1

Installing the Motherboard

https://youtu.be/wWI6Qt51Wnc

⚽

Torque:

3 kgf·cm*

*3 kgf·cm

= 0.3 N·m

= 2.6 lbf·in

Quick Start

Connecting the Power Connectors

http://youtu.be/gkDYyR_83I4

ATX_PWR1

CPU_PWR1

⚽

CPU_PWR2

10 Quick Start

Installing SATA Drives

http://youtu.be/RZsMpqxythc

⚽

Quick Start

Installing a Graphics Card

http://youtu.be/mG0GZpr9w_A

⚽

12 Quick Start

Connecting Peripheral Devices

Quick Start

Power On

14 Contents

Contents

Quick Start ............................................................................................................. 1

Preparing Tools and Components.......................................................................... 1

Safety Information .................................................................................................. 2

Case stand-off notification ..................................................................................... 3

Avoid collision notification ...................................................................................... 3

Installing a Processor ............................................................................................ 4

Installing DDR4 memory ........................................................................................ 6

Connecting the Front Panel Header ...................................................................... 7

Installing the Motherboard ..................................................................................... 8

Connecting the Power Connectors ........................................................................ 9

Installing SATA Drives .......................................................................................... 10

Installing a Graphics Card .................................................................................... 11

Connecting Peripheral Devices ............................................................................ 12

Power On .............................................................................................................. 13

Specifications ....................................................................................................... 17

JCORSAIR1 Connector Specification .................................................................. 24

Package contents ................................................................................................ 25

Block Diagram .................................................................................................... 26

Rear I/O Panel ..................................................................................................... 27

LAN Port LED Status Table .................................................................................. 27

Audio Ports Configuration .................................................................................... 27

Realtek Audio Console ......................................................................................... 28

Installing Antennas ............................................................................................... 30

Overview of Components .................................................................................... 31

Processor Socket ................................................................................................. 33

DIMM Slots ............................................................................................................ 34

PCI_E1~4: PCIe Expansion Slots .......................................................................... 35

PCIe bandwidth table ............................................................................................ 35

Bandwidth share table ......................................................................................... 36

M2_1~4: M.2 Slots (Key M) ................................................................................... 38

Installing M.2 XPANDER-Z Gen4 S card .............................................................. 40

SATA1~8: SATA 6Gb/s Connectors ....................................................................... 42

JFP1, JFP2: Front Panel Connectors ................................................................... 42

CPU_PWR1~2, ATX_PWR1: Power Connectors ................................................... 43

JOC_FS1: Safe Boot Jumper ................................................................................ 44

Contents

T_SEN1~2: Thermal Sensor Connectors ............................................................. 44

W_FLOW1: Water Flow Meter Connector ............................................................ 44

JLN1: Low Temperature Booting Jumper ........................................................... 45

JAUD1: Front Audio Connector ............................................................................ 45

JUSB1: USB 3.2 Gen 2 Type-C Connector ............................................................ 46

JUSB2~3: USB 3.2 Gen1 Connector ..................................................................... 46

JUSB4~5: USB 2.0 Connectors ............................................................................. 47

JTPM1: TPM Module Connector ........................................................................... 47

CPU_FAN1, PUMP_FAN1, SYS_FAN1~6: Fan Connectors .................................. 48

JCI1: Chassis Intrusion Connector ....................................................................... 49

JDASH1 : Tuning Controller connector ................................................................ 49

JBAT1: Clear CMOS (Reset BIOS) Jumper ........................................................... 50

POWER1, RESET1: Power Button, Reset Button ................................................. 50

JRGB1: RGB LED connector ................................................................................. 51

JRAINBOW1~2: Addressable RGB LED connectors ............................................ 52

JCORSAIR1: CORSAIR Connector ........................................................................ 53

Onboard LEDs ...................................................................................................... 54

EZ Debug LED ....................................................................................................... 54

JPWRLED1: LED power input ............................................................................... 54

LED_SW1: EZ LED Control ................................................................................... 54

Debug Code LED ................................................................................................... 55

Hexadecimal Character Table .............................................................................. 55

Boot Phases .......................................................................................................... 55

Debug Code LED Table ......................................................................................... 55

ACPI States Codes ................................................................................................ 59

Installing OS, Drivers & MSI Center .................................................................... 60

Installing Windows® 10 ......................................................................................... 60

Installing Drivers .................................................................................................. 60

MSI Center ............................................................................................................ 60

UEFI BIOS ............................................................................................................. 61

BIOS Setup ........................................................................................................... 62

Entering BIOS Setup ............................................................................................. 62

BIOS User Guide ................................................................................................... 62

Resetting BIOS ...................................................................................................... 63

Updating BIOS ....................................................................................................... 63

Nahimic 3 ............................................................................................................. 65

Installation and Update ........................................................................................ 65

16 Contents

Audio Tab .............................................................................................................. 65

Microphone Tab .................................................................................................... 66

Sound Tracker Tab ............................................................................................... 67

Settings Tab .......................................................................................................... 67

RAID Configuration .............................................................................................. 68

Troubleshooting ................................................................................................. 69

Specifications

CPU

∙Supports AMD Ryzen™ 5000 Series, 5000 G-Series 4000

G-Series, 3000 Series, 3000 G-Series, 2000 Series and 2000

G-Series desktop processors*

∙Supports Socket AM4

* Please go to msi.com to get the newest support status as new processors are

released.

Chipset AMD X570 Chipset

Memory

∙4x DDR4 memory slots, support up to 128GB

∙Supports 1866/ 2133/ 2400/ 2667/ 2800/ 2933/ 3000/ 3066/

3200 MHz by JEDEC*

∙Max frequency by A-XMP OC mode:

▪For Ryzen™ 5000 G-Series & 4000 G-Series

processors

▫1DPC 1R Max speed up to 5300 MHz (support

overclocking up to 5500+ MHz)

▫1DPC 2R Max speed up to 4266 MHz

▫2DPC 1R Max speed up to 4400 MHz

▫2DPC 2R Max speed up to 3600 MHz

▪For Ryzen™ 5000 Series & 3000 Series processors

▫1DPC 1R Max speed up to 5100 MHz

▫1DPC 2R Max speed up to 4000 MHz

▫2DPC 1R Max speed up to 4000 MHz

▫2DPC 2R Max speed up to 3600 MHz

∙Supports Dual-Channel mode

∙Supports non-ECC, un-buffered memory

*Please refer to www.msi.com for more information on compatible memory

Continued on next page

18 Specifications

Continued from previous page

Expansion Slots

∙Supports PCIe 4.0 / PCIe 3.0

▪PCIe 4.0 is available only on AMD Ryzen™ 5000 Series

and 3000 Series desktop processors

∙2x PCIe x16 slots (From processor)

▪PCI_E1 & PCI_E2 support x16/ x0, X8/ X8 for AMD

Ryzen™ 5000 Series, 5000 G-Series, 4000 G-Series,

3000 Series and 2000 Series desktop processors

▪PCI_E1 & PCI_E2 support x8/ x0 for AMD Ryzen™

2000 G-Series and 3000 G-Series desktop processors

∙1x PCIe x16 slot (From X570 chipset)

▪PCI_E4 supports x8*

∙1x PCIe x1 slot (From X570 chipset)**

* PCI_E4, M2_3, M2_4 and SATA5~8 share the same bandwidth. Please see the

page 36 for more details.

** The PCIe x1 slot and onboard Wi-Fi module share the same bandwidth, you

can not use both of them simultaneously, and the default setting is the Wi-Fi

module for the system. Please disable the Onboard Wi-Fi Module Control in

BIOS if you want to use the PCIe x1 slot.

Multi-GPU ∙Supports NVIDIA® SLI® Technology

∙Supports AMD CrossFire™ Technology

LAN 1x Realtek® RTL8125B 2.5 Gbps LAN controller

Wireless LAN &

Bluetooth®

Intel® Wi-Fi 6E AX210

∙The Wireless module is pre-installed in the M.2 (Key-E)

slot

∙Supports MU-MIMO TX/RX, 2.4GHz/ 5GHz/ 6GHz*

(160MHz) up to 2.4Gbps

∙Supports 802.11 a/ b/ g/ n/ ac/ ax

∙Supports Bluetooth® 5.2**, FIPS, FISMA

* Wi-Fi 6E 6GHz may depend on every country’s regulations and will be ready in

WIN10 21H1.

** Bluetooth 5.2 will be ready in WIN10 21H1.

Audio

Realtek® ALC4082 Codec + ESS SABRE9018Q2C Combo

DAC/HPA

∙7.1-Channel High Definition Audio

∙Supports S/PDIF output

Continued on next page

Specifications

Continued from previous page

Storage

∙8x SATA 6Gb/s ports (From X570 chipset)*

∙4x M.2 slots (Key M)*

▪Supports PCIe 4.0 / PCIe 3.0

▫PCIe 4.0 is available only on AMD Ryzen™ 5000

Series and 3000 Series desktop processors

▪Support SATA 6Gbps (For M2_1, M2_3 & M2_4)

▪M2_1 (From processor)

▫Supports 2280/ 22110 storage devices

▪M2_2 (From X570 chipset)

▫Supports 2260/ 2280 storage devices

▪M2_3* (From X570 chipset)

▫Supports 2280/ 22110 storage devices

▪M2_4* (From X570 chipset)

▫Supports 2260/ 2280 storage devices

* PCI_E4, M2_3, M2_4 and SATA5~8 share the same bandwidth. Please see the

page 36 for more details.

RAID AMD X570 Chipset

∙Supports RAID 0, RAID 1 and RAID 10

USB

AMD X570 Chipset

∙1x USB 3.2 Gen 2 10Gbps Type-C internal connector

∙4x USB 3.2 Gen 1 5Gbps ports available through internal

USB connectors)

∙1x USB 2.0 port on the back panel

∙Asmedia® 3241 Chipset

▪1x USB 3.2 Gen 2x2 20Gbps Type-C port on the back

panel

∙USB 3.0 Hub

▪4x USB 3.2 Gen 1 5Gbps Type-A ports on the back

panel

∙USB 2.0 Hub

▪7x USB 2.0 ports (3 Type-A ports on the back panel, 4

ports available through the internal USB connectors)

AMD Processor

∙3x USB 3.2 Gen 2 10Gbps Type-A ports on the back panel

Continued on next page

20 Specifications

Continued from previous page

Back Panel

Connectors

∙1x Clear CMOS Button

∙1x Flash BIOS Button

∙4x USB 2.0 ports

∙4x USB 3.2 Gen 1 5Gbps Type-A ports

∙1x LAN(RJ45) port

∙3x USB 3.2 Gen 2 10Gbps Type-A ports

∙1x USB 3.2 Gen 2x2 20Gbps Type-C port

∙2x Wi-Fi Antenna connectors

∙5x OFC audio jacks

∙1x Optical S/PDIF Out connector

Internal Connectors

∙1x 24-pin ATX main power connector

∙2x 8-pin ATX 12V power connectors

∙8x SATA 6Gb/s connectors

∙4x M.2 slots (M-Key)

∙2x USB 2.0 connectors (support additional 4 USB ports)

∙2x USB 3.2 Gen 1 5Gbps connectors (support additional 4

USB ports)

∙1x USB 3.2 Gen 2 10Gbps Type-C connector

∙1x 4-pin CPU fan connector

∙1x 4-pin water-pump connector

∙6x 4-pin system fan connectors

∙1x Front panel audio connector

∙2x System panel connectors

∙1x TPM module connector

∙1x Chassis Intrusion connector

∙2x 2-pin Thermal sensors connectors

∙1x Water Flow Meter connector

∙1x Tuning Controller connector

Buttons ∙1x Power button

∙1x Reset button

Continued on next page

Specifications

Continued from previous page

Jumpers

∙1x Clear CMOS jumper

∙1x Low temperature booting jumper

∙1x Safe Boot jumper

LED Features

∙1x 4-pin RGB LED connector

∙2x 3-pin RAINBOW LED connectors

∙1x 3-pin CORSAIR connector

∙1x EZ LED Control switch

∙1x 2-Digit Debug Code LED

∙4x EZ Debug LEDs

I/O Controller NUVOTON NCT6687D Controller Chip

Hardware Monitor

∙CPU/ System/ Chipset temperature detection

∙CPU/ System/ Pump fan speed detection

∙CPU/ System/ Pump fan speed control

Form Factor ∙ATX Form Factor

∙12 in. x 9.6 in. (30.5 cm x 24.4 cm)

BIOS Features

∙2x 256 Mb flash

∙UEFI AMI BIOS

∙ACPI 6.2, SM BIOS 3.0

∙Multi-language

Software

∙Drivers

∙MSI Center

∙Nahimic

∙MSI APP Player (Bluestack)

∙Open Broadcaster Software (OBS)

∙CPU-Z MSI GAMING

∙Google Chrome™, Google Toolbar, Google Drive

∙Norton™ Internet Security Solution

Continued on next page

22 Specifications

Continued from previous page

MSI Center

Features

∙Duet Display

∙Gaming Mode

∙Creator Mode

∙Game Highlights

∙LAN Manager

∙Mystic Light

∙Ambient Link

∙Frozr AI Cooling

∙User Scenario

∙True Color

∙Live Update

∙Monitor

∙Super Charger

∙Speed Up

∙Smart Image Finder

∙MSI Companion

Continued on next page

Specifications

Continued from previous page

Special Features

∙Audio

▪Audio Boost 5 HD

▪Nahimic 3

∙Network

▪2.5G LAN

▪LAN Manager

▪Intel WiFi

∙Cooling

▪All Aluminum Design

▪Mosfet Baseplate

▪M.2 Shield Frozr

▪K7 thermal pad

▪Choke Pad

▪Pump Fan

▪Smart Fan Control

∙LED

▪Mystic Light

▪Mystic Light Extension (RGB)

▪Mystic Light Extension (RAINBOW)

▪Mystic Light Extension (CORSAIR)

▪Mystic Light SYNC

▪Ambient Link

▪EZ LED Control

▪EZ DEBUG LED

∙Protection

▪PCI-E Steel Armor

▪Pre-installed I/O Shield

Continued on next page

24 Specifications

Continued from previous page

Special Features

∙Performance

▪Lightning Gen 4 PCI-E Slot

▪Lightning Gen 4 M.2

▪Multi GPU – SLI Technology

▪Multi GPU – CrossFire Technology

▪DDR4 Boost

▪Core Boost

▪Game Boost

▪Lightning USB 20G

▪USB 3.2 Gen 2 10G

▪USB with Type A+C

▪Front USB Type-C

▪Dual CPU Power

▪Server PCB

▪2oz Copper thickened PCB

∙Experience

▪MSI Center

▪Duet Display

▪Frozr AI Cooling

▪Click BIOS 5

▪System Saver

▪Flash BIOS Button

JCORSAIR1 Connector Specification

Supporting CORSAIR RGB Products Maximum connection

Lighting PRO RGB LED Strip

20*

* 20% brightness is recommended when the number of

LED strips exceeds 8.

HD120 RGB Fan 6

SP120 RGB Fan 6

LL120 RGB Fan 6

Package contents

Please check the contents of your motherboard package. It should contain:

Motherboard MEG X570S ACE MAX

Documentation User Manual 1

Quick Installation Guide 1

Application USB drive with drivers & utilities 1

Cable

SATA 6Gb/s Cables 4

LED JRGB Y Cable 1

LED JCORSAIR Cable 1

LED JRAINBOW Cable 1

Thermistor cable 2

Accessories

Wi-Fi Antenna 1

M.2 XPANDER-Z GEN 4 S card 1

M.2 screw + standoff (2 sets/pack) 2

Case Badge 1

MEG sticker 1

SATA Cable Labels 1

Product Registration Card 1

Gift Small screwdriver set 1

Small Brush 1

⚠

Important

If any of the above items are damaged or missing, please contact your retailer.

26 Block Diagram

Block Diagram

CPU

Chipset

DDR4 2Channel

DIMM A1,A2

DIMM B1,B2

PCIE x4

PCI_E2

(Max. x8)

WiFi AX210

2.5G LAN

HD Audio

ALC4082

ESS 9018Q2C

M2_1

PCI_E4

(Max. x8)

PCI_E3

M2_4

M2_2

M2_3

ESIO

NCT 6687D-R

TPM

SPI

MCU

USB 3.2 Gen 2 10Gbps

USB 3.2 Gen 1 5Gbps

USB 3.2 Gen 2 10Gbps

USB 3.2 Gen 2x2

20Gbps

USB 2.0

Hub

USB 2.0

Asmedia 3241

SATA1/ 2/ 3/ 4

SATA5/ 6/ 7/ 8

Switch

PCI_E1

(Max. x16)

Rear I/O Panel

Audio Ports Configuration

Audio Ports Channel

2468

Center/ Subwoofer Out  

Rear Speaker Out 

Line-In/ Side Speaker Out 

Line-Out/ Front Speaker Out 

Mic In

Blank: empty)

Rear I/O Panel

∙Clear CMOS button - Power off your computer. Press and hold the Clear CMOS

button for about 5-10 seconds to reset BIOS to default values.

∙Flash BIOS Port/ Button - Please refer to page 64 for Updating BIOS with Flash BIOS

Button.

USB 3.2 Gen 2

10Gbps Type-A

2.5 Gbps

LAN

USB 2.0

Audio Ports

Optical S/PDIF-Out

Clear CMOS

button

Wi-Fi Antenna

connectors

USB 3.2 Gen 2x2

20Gbps Type-C

Flash BIOS

Button Flash BIOS Port

USB 3.2 Gen 1

5Gbps Type-A

LAN Port LED Status Table

Link/ Activity LED

Status Description

Off No link

Yellow Linked

Blinking Data activity

Speed LED

Status Description

Off 10 Mbps connection

Green 100/1000 Mbps connection

Orange 2.5 Gbps connection

28 Rear I/O Panel

Realtek Audio Console

After Realtek Audio Console is installed. You can use it to change sound settings to get

better sound experience.

∙Device Selection - allows you to select a audio output source to change the related

options. The check sign indicates the devices as default.

∙Application Enhancement - the array of options will provide you a complete

guidance of anticipated sound effect for both output and input device.

∙Main Volume - controls the volume or balance the right/left side of the speakers

that you plugged in front or rear panel by adjust the bar.

∙Jack Status - depicts all render and capture devices currently connected with your

computer.

∙Connector Settings - configures the connection settings.

Auto popup dialog

When you plug into a device at an audio jack, a dialogue window will pop up asking you

which device is current connected.

Each jack corresponds to its default setting as shown on the next page.

⚠

Important

The pictures above for reference only and may vary from the product you purchased.

Jack Status

Connector Settings

Device

Selection

Main Volume

Application Enhancement

Rear I/O Panel

Audio jacks to headphone and microphone diagram

Audio jacks to stereo speakers diagram

Audio jacks to 7.1-channel speakers diagram

AUDIO INPUT

Rear Front

Side Center/

Subwoofer

30 Rear I/O Panel

Installing Antennas

1. Combine the antenna with the base.

2. Screw two antenna cables tight to the WiFi antenna connectors as shown.

3. Place the antenna as high as possible.

Overview of Components

BAT1

RESET1

JRAINBOW1

JFP2

JOC_FS1

JFP1



M2_1

JUSB2

JLN1

JUSB1







CPU_FAN1

PUMP_FAN1

PCI_E1

JTPM1

SYS_FAN6

M2_3

M2_2

PCI_E2

M2_4

JBAT1

JDASH1

PCI_E4

PCI_E3

JCI1

JRAINBOW2

LED_SW1

JPWRLED1

T_SEN1

T_SEN2

Processor

Socket

CPU_PWR1

CPU_PWR2

JSMB1

JCORSAIR1

JUSB3

POWER1

JUSB4

W_FLOW1

SYS_FAN3

BIOS_SW1

SYS_FAN4

SYS_FAN5

JRGB1

JAUD1

ATX_PWR1

SYS_FAN1

SYS_FAN2

DIMMB2

DIMMB1

DIMMA2

DIMMA1

JUSB5

32 Overview of Components

Component Contents

Port Name Port Type Page

CPU_FAN1, PUMP_FAN1,

SYS_FAN1~6 Fan Connectors 48

CPU_PWR1~2, ATX_PWR1 Power Connectors 43

DIMMA1, DIMMA2, DIMMB1,

DIMMB2 DIMM Slots 34

JAUD1 Front Audio Connector 45

JBAT1 Clear CMOS Jumper 50

JCI1 Chassis Intrusion Connector 49

JCORSAIR1 CORSAIR Connector 53

JDASH1 Tuning Controller connector 49

JFP1, JFP2 Front Panel Connectors 42

JLN1 Low Temperature Booting Jumper 45

JOC_FS1 Safe Boot Jumper 44

JPWRLED1 LED power input 54

JRAINBOW1~2 Addressable RGB LED connectors 52

JRGB1 RGB LED connector 51

JTPM1 TPM Module Connector 47

JUSB1 USB 3.2 Gen 2 Type-C Connector 46

JUSB2~3 USB 3.2 Gen1 Connector 46

JUSB4~5 USB 2.0 Connectors 47

LED_SW1 EZ LED Control 54

M2_1~4 M.2 Slots (Key M) 38

PCI_E1~4 PCIe Expansion Slots 35

POWER1, RESET1 Power Button, Reset Button 50

Processor Socket AM4 socket 33

SATA1~8 SATA 6Gb/s Connectors 42

T_SEN1~2 Thermal Sensor Connectors 44

W_FLOW1 Water Flow Meter Connector 44

󳖮󴉣󴁂

Overview of Components

Processor Socket

⚠

Important

∙

When changing the processor, the system configuration could be cleared and reset

BIOS to default values, due to the AM4 processor’s architecture.

∙

Always unplug the power cord from the power outlet before installing or removing

the CPU.

∙

When installing a CPU, always remember to install a CPU heatsink. A CPU heatsink

is necessary to prevent overheating and maintain system stability.

∙

Confirm that the CPU heatsink has formed a tight seal with the CPU before booting

your system.

∙

Overheating can seriously damage the CPU and motherboard. Always make sure

the cooling fans work properly to protect the CPU from overheating. Be sure to apply

an even layer of thermal paste (or thermal tape) between the CPU and the heatsink to

enhance heat dissipation.

∙

If you purchased a separate CPU and heatsink/ cooler, Please refer to the

documentation in the heatsink/ cooler package for more details about installation.

∙

This motherboard is designed to support overclocking. Before attempting to

overclock, please make sure that all other system components can tolerate

overclocking. Any attempt to operate beyond product specifications is not

recommended. MSI® does not guarantee the damages or risks caused by inadequate

operation beyond product specifications.

Introduction to the AM4

processor

The surface of the AM4 processor

has a yellow triangle to assist in

correctly lining up the processor for

motherboard placement. The yellow

triangle is the Pin 1 indicator.

53.62 mm

Distance from the center of the

CPU to the nearest DIMM slot.

34 Overview of Components

DIMM Slots

DIMMA1 DIMMB1

Channel A Channel B

DIMMA2 DIMMB2

Memory module installation recommendation

⚠

Important

∙

Always insert memory modules in the DIMMA2 slot first.

∙

Due to chipset resource usage, the available capacity of memory will be a little less

than the amount of installed.

∙

Based on processor specification, the Memory DIMM voltage below 1.35V is

suggested to protect the processor.

∙

Some memory modules may operate at a lower frequency than the marked value

when overclocking due to the memory frequency operates dependent on its Serial

Presence Detect (SPD). Go to BIOS and find the DRAM Frequency! to set the memory

frequency if you want to operate the memory at the marked or at a higher frequency.

∙

It is recommended to use a more efficient memory cooling system for full DIMMs

installation or overclocking.

∙

The stability and compatibility of installed memory module depend on installed CPU

and devices when overclocking.

∙

Due to AM4 processor/ memory controller official specification limitation, the

frequency of memory modules may operate lower than the marked value under

the default state. Please refer www.msi.com for more information on compatible

memory.

DIMMB2 DIMMB2

DIMMB1

DIMMA2 DIMMA2 DIMMA2

DIMMA1

Overview of Components

PCI_E1~4: PCIe Expansion Slots

⚠

Important

∙

If you install a large and heavy graphics card, you need to use a tool such as MSI

Gaming Series Graphics Card Bolster to support its weight to prevent deformation of

the slot.

∙

For a single PCIe x16 expansion card installation with optimum performance, using

the PCI_E1 slot is recommended.

∙

When adding or removing expansion cards, always turn off the power supply and

unplug the power supply power cable from the power outlet. Read the expansion

card’s documentation to check for any necessary additional hardware or software

changes.

∙

The PCIe x1 slot and onboard Wi-Fi module share the same bandwidth, you can not

use both of them simultaneously, and the default setting is the Wi-Fi module for the

system. Please disable the Onboard Wi-Fi Module Control in BIOS if you want to use

the PCIe x1 slot.

PCIe bandwidth table

AMD Ryzen™ 5000 Series, 5000 G-Series, 4000 G-Series, 3000 Series and 2000

Series desktop processors

Slot Single VGA 2-Way VGA 3-Way VGA

PCI_E1 (CPU) @ x16 @ x8 @ x8

PCI_E2 (CPU) — @ x8 @ x8

PCI_E3 (Chipset) x1 x1 x1

PCI_E4 (Chipset) x8/ x4 x8/ x4 @ x8/ @x4*



Slots AMD Ryzen™

5000/ 3000 series

processors

AMD Ryzen™ 5000

G-/ 4000 G-/ 2000

series processors

AMD Ryzen™ 3000

G-/ 2000 G- series

processors

PCI_E1 (CPU) PCIe 4.0 x16 PCIe 3.0 x16 PCIe 3.0 x8

PCI_E2 (CPU) PCIe 4.0 x8 PCIe 3.0 x8 —

PCI_E3 (Chipset) PCIe 4.0 x1 PCIe 3.0 x1 PCIe 3.0 x1

PCI_E4 (Chipset) PCIe 4.0 x8 PCIe 3.0 x8 PCIe 3.0 x8

⚠

Important

PCI_E4, M2_3, M2_4 and SATA5~8 share the same bandwidth. Please refer to the

following Bandwidth share table for more details.

36 Overview of Components

Bandwidth share table

PCI_E4, M2_3, M2_4 & SATA5~8

Slot Bandwidth configuration

PCI_E4 (Chipset) x8 x4

M2_3 (Chipset) PCIe SATA 

M2_4 (Chipset) PCIe SATA PCIe SATA

SATA5~6 (Chipset)   VV

SATA7~8 (Chipset)  



AMD Ryzen™ 2000 G-Series and 3000 G-Series desktop processors

Slot Single VGA 2-Way VGA

PCI_E1 (CPU) @ x8 @ x8

PCI_E2 (CPU) — —

PCI_E3 (Chipset) x1 x1

PCI_E4 (Chipset) x8/ x4 @x8/ @x4*



⚠

Important

PCI_E4, M2_3, M2_4 and SATA5~8 share the same bandwidth. Please refer to the

following Bandwidth share table for more details.

Overview of Components

Installing SLI graphics cards

For power supply recommendations for SLI configurations, please refer to the user

guide of your graphics card to make sure you meet all the system requirements.

To install SLI graphics cards:

1. Turn off your computer and disconnect the power cord, install two graphics cards

into the PCI_E1 & PCI_E2 or PCI_E1 & PCI_E4 slots.

2. Connect the two cards together using the SLI Bridge Connector.

3. Connect all PCIe power connectors of the graphics cards.

4. Reconnect the power cord, power up the computer and install the drivers and

software included in your graphics card package.

5. Right-click the Windows desktop and select NVIDIA Control Panel from the menu,

click on Configure SLI, Surround, PhysX in the left task panel and select Maximize

3D performance in the SLI configuration menu, and then click Apply.

38 Overview of Components

M2_1~4: M.2 Slots (Key M)

Installing M.2 module

1. Loosen the screws of M.2 SHIELD FROZR heatsink.

2. Remove the M.2 SHIELD FROZR and remove the protective films from the thermal

pads.

1 1

M2_1 (CPU)

M2_2 (Chipset)

M2_3 (Chipset)

M2_4 (Chipset)

⚽

Video Demonstration

Watch the video to learn how to Install

M.2 SSD.

https://youtu.be/2UeWMgjwogU

M2_1

M2_2 & M2_3

M2_4

Overview of Components

3. Secure the supplied M.2 standoff according to your M.2 SSD length if need.

4. Insert your M.2 SSD into the M.2 slot at a 30-degree angle.

5. Secure the M.2 SSD in place with the supplied M.2 8.5H screw.

⚠

Important

Skip step 3 and step 5, if you install 22110 M.2 into M2_1 & M2_3 slots or install 2280

M.2 into M2_2 & M2_4 slots.

6. Put the M.2 SHIELD FROZR heatsink back in place and secure it.

30º30º

8.5H screw

Standoff

40 Overview of Components

30º30º

M.2 Screw

M.2 Standoff

Installing M.2 XPANDER-Z Gen4 S card

To install the M.2 XPANDER-Z GEN 4 S card, please follows the steps below.

1. Remove the heatsink by loosening four screws on the back of the card.

2. Loosen M.2 screw from M.2 standoff.

3. Loosen M.2 standoff.

4. Move the position of the standoffs according to your M.2 SSDs length if need.

5. Insert your M.2 SSD into the M.2 slot at a 30-degree angle.

6. Secure the M.2 device in place with M.2 screw.

8 8

7. Remove the protective film from the thermal pad of the heatsink.

8. Reinstall and secure the heatsink with four heatsink screws.

*The speeds depends on the

devices being used.

1 1

Overview of Components

9. Insert the card into the PCI_E2 slot.

10. Use a screw to secure the card.

11. Connect the PCIE_PWR1 to the power supply.

12. Connect the case’s HDD LED cable to the JCASE connector.

13. Using the supplied HDD LED cable to connect the JMB connector and JFP1’s HDD

pins (pin 1 & pin3).

14. Using the supplied JSMB cable to connect the JSMB connector on the card and

JSMB1 connector on the motherboard. And then you can set the fan duty cycle and

the LED color of the card in BIOS.

PCI_E2

HDD LED

JFP1

JSMB1

PCIE_PWR1

JCASE

JMB

JSMB

42 Overview of Components

SATA1~8: SATA 6Gb/s Connectors

These connectors are SATA 6Gb/s interface ports. Each connector can connect to one

SATA device.

SATA1

SATA5

SATA3

SATA7

SATA2

SATA6

SATA4

SATA8

⚠

Important

∙

Please do not fold the SATA cable at a 90-degree angle. Data loss may result during

transmission otherwise.

∙

SATA cables have identical plugs on either sides of the cable. However, it is

recommended that the flat connector be connected to the motherboard for space

saving purposes.

JFP1, JFP2: Front Panel Connectors

These connectors connect to the switches and LEDs on the front panel.

JFP2

Speaker

Buzzer 1 Speaker - 2 Buzzer +

3 Buzzer - 4 Speaker +

2 10

+- --

Power LED

HDD LED Reset Switch

Reserved

Power Switch

JFP1

1 HDD LED + 2 Power LED +

3 HDD LED - 4 Power LED -

5 Reset Switch 6 Power Switch

7 Reset Switch 8 Power Switch

9 Reserved 10 No Pin

Overview of Components

131

ATX_PWR1

1 +3.3V 13 +3.3V

2 +3.3V 14 -12V

3 Ground 15 Ground

4 +5V 16 PS-ON#

5 Ground 17 Ground

6 +5V 18 Ground

7 Ground 19 Ground

8 PWR OK 20 Res

9 5VSB 21 +5V

10 +12V 22 +5V

11 +12V 23 +5V

12 +3.3V 24 Ground

4 1

8CPU_PWR1~2

1 Ground 5 +12V

2 Ground 6 +12V

3 Ground 7 +12V

4 Ground 8 +12V

⚠

Important

Make sure that all the power cables are securely connected to a proper ATX power

supply to ensure stable operation of the motherboard.

CPU_PWR1~2, ATX_PWR1: Power Connectors

These connectors allow you to connect an ATX power supply.

44 Overview of Components

T_SEN1~2: Thermal Sensor Connectors

These connectors allow you to connect the thermistor cable and use it to monitor the

temperature of the detection point.

Thermistor cable

GND

Sense

W_FLOW1: Water Flow Meter Connector

This connector allows you to connect a flow meter to monitor the flow rate of your

liquid cooling system.

1 Ground 3 WFLOW IN

2 WFLOW PWR (2A)

Normal Boot

(default) Enabled

Boot with lower PCIe

(from CPU) mode for

Safe Boot.

JOC_FS1: Safe Boot Jumper

This jumper is used for Safe Boot. Once enabled, the system will boot with lower PCIe

(from CPU) mode.

Overview of Components

JAUD1: Front Audio Connector

This connector allows you to connect audio jacks on the front panel.

2 10

1 MIC L 2 Ground

3 MIC R 4 NC

5 Head Phone R 6 MIC Detection

7 SENSE_SEND 8 No Pin

9 Head Phone L 10 Head Phone Detection

Enabled

(Please enable this jumper

during BIOS POST.)

Normal

(Default)

⚠

Important

∙

Users will try extreme low temperature overclocking at their own risks. The

overclocking results will vary according to the CPU version.

∙

Please don’t set to Enabled when power-off or the system will be un-bootable.

JLN1: Low Temperature Booting Jumper

This jumper is used for liquid nitrogen cooling system to boot at an extreme low

temperature. Try to set it Enabled to increase the boot success rate.

46 Overview of Components

JUSB1: USB 3.2 Gen 2 Type-C Connector

This connector allows you to connect USB 3.2 Gen 2 Type-C connector on the front

panel. The connector possesses a foolproof design. When you connect the cable, be

sure to connect it with the corresponding orientation.

JUSB2~3: USB 3.2 Gen1 Connector

These connectors allow you to connect USB 3.2 Gen1 ports on the front panel.

⚠

Important

Note that the Power and Ground pins must be connected correctly to avoid possible

damage.

10 11

JUSB2

1 10

1120

JUSB3

1 Power 11 USB2.0+

2 USB3_RX_DN 12 USB2.0-

3 USB3_RX_DP 13 Ground

4 Ground 14 USB3_TX_C_DP

5 USB3_TX_C_DN 15 USB3_TX_C_DN

6 USB3_TX_C_DP 16 Ground

7 Ground 17 USB3_RX_DP

8 USB2.0- 18 USB3_RX_DN

9 USB2.0+ 19 Power

10 NC 20 No Pin

JUSB1 USB Type-C Cable

USB Type-C port on

the front panel

Overview of Components

JUSB4~5: USB 2.0 Connectors

These connectors allow you to connect USB 2.0 ports on the front panel.

2 10

1 VCC 2 VCC

3 USB0- 4 USB1-

5 USB0+ 6 USB1+

7 Ground 8 Ground

9 No Pin 10 NC

⚠

Important

∙

Note that the VCC and Ground pins must be connected correctly to avoid possible

damage.

∙

In order to recharge your iPad,iPhone and iPod through USB ports, please install

MSI® Center utility.

JTPM1: TPM Module Connector

This connector is for TPM (Trusted Platform Module). Please refer to the TPM security

platform manual for more details and usages.

12 11

1 SPI Power 2 SPI Chip Select

Master In Slave Out (SPI Data)

Master Out Slave In (SPI Data)

5 Reserved 6 SPI Clock

7 Ground 8 SPI Reset

9 Reserved 10 No Pin

11 Reserved 12 Interrupt Request

48 Overview of Components

CPU_FAN1, PUMP_FAN1, SYS_FAN1~6: Fan Connectors

Fan connectors can be classified as PWM (Pulse Width Modulation) Mode or DC Mode.

PWM Mode fan connectors provide constant 12V output and adjust fan speed with

speed control signal. DC Mode fan connectors control fan speed by changing voltage.

The auto mode fan connectors can automatically detect PWM and DC mode. However,

you can follow the instruction below to adjust the fan connector to PWM or DC Mode

manually.

Connector Default

fan mode Max.

current Max.

power

CPU_FAN1 Auto mode 3A 36W

PUMP_FAN1 PWM mode 3A 36W

SYS_FAN1~6 DC mode 2A 24W

⚠

Important

Make sure fans are working properly after switching the PWM/ DC mode.

Pin definition of fan connectors

1 PWM Mode pin definition

1 Ground 2 +12V

3 Sense 4 Speed Control Signal

1 DC Mode pin definition

1 Ground 2 Voltage Control

3 Sense 4 NC

CPU_FAN1

SYS_FAN2

SYS_FAN1

SYS_FAN6

SYS_FAN5

SYS_FAN4

SYS_FAN3

PUMP_FAN1

Switching fan mode and adjusting fan speed

You can switch between PWM mode and DC mode and adjust fan speed in BIOS >

HARDWARE MONITOR.

Select PWM mode or DC mode

There are gradient points of the fan speed that allow you to adjust

fan speed in relation to CPU temperature.

Overview of Components

JCI1: Chassis Intrusion Connector

This connector allows you to connect the chassis intrusion switch cable.

Normal

(default) Trigger the chassis

intrusion event

Using chassis intrusion detector

1. Connect the JCI1 connector to the chassis intrusion switch/ sensor on the chassis.

2. Close the chassis cover.

3. Go to BIOS > SETTINGS > Security > Chassis Intrusion Configuration.

4. Set Chassis Intrusion to Enabled.

5. Press F10 to save and exit and then press the Enter key to select Yes.

6. Once the chassis cover is opened again, a warning message will be displayed on

screen when the computer is turned on.

Resetting the chassis intrusion warning

1. Go to BIOS > SETTINGS > Security > Chassis Intrusion Configuration.

2. Set Chassis Intrusion to Reset.

3. Press F10 to save and exit and then press the Enter key to select Yes.

JDASH1 : Tuning Controller connector

This connector is used to connect an optional Tuning Controller module.

2 14

1 No Pin 2 NC

3 MCU_SMB_SCL_M 4 MCU_SMB_SDA_M

5 VCC5 6 Ground

7 PSIN#_R 8 FP_RST#_R

9 OC_RETRY# 10 OC_FS

11 BLK+ 12 BLK-

13 CLRCMOS_EN 14 NC

50 Overview of Components

JBAT1: Clear CMOS (Reset BIOS) Jumper

There is CMOS memory onboard that is external powered from a battery located on

the motherboard to save system configuration data. If you want to clear the system

configuration, set the jumpers to clear the CMOS memory.

Keep Data

(default) Clear CMOS/

Reset BIOS

Resetting BIOS to default values

1. Power off the computer and unplug the power cord.

2. Use a jumper cap to short JBAT1 for about 5-10 seconds.

3. Remove the jumper cap from JBAT1.

4. Plug the power cord and Power on the computer.

POWER1, RESET1: Power Button, Reset Button

The Power / Reset button allows you to power on / reset the computer.

Power button

Reset

Reset button

Overview of Components

⚠

Important

∙

The JRGB connector supports up to 2 meters continuous 5050 RGB LED strips

(12V/G/R/B) with the maximum power rating of 3A (12V).

∙

Always turn off the power supply and unplug the power cord from the power outlet

before installing or removing the RGB LED strip.

∙

Please use MSI’s software to control the extended LED strip.

JRGB1: RGB LED connector

The JRGB connector allows you to connect the 5050 RGB LED strips 12V.

GRB

JRGB

connector

RGB extension

cable 5050 RGB LED strips 12V

1 +12V 2 G

3 R 4 B

RGB LED Strip Connection

GRB

JRGB connector

System Fan connector

RGB LED Fan Connection

RGB LED Fan

52 Overview of Components

+5V

⚠

CAUTION

Do not connect the wrong type of LED strips. The JRGB connector and the JRAINBOW

connector provide different voltages, and connecting the 5V LED strip to the JRGB

connector will result in damage to the LED strip.

⚠

Important

∙

The JRAINBOW connector supports up to 75 LEDs WS2812B Individually

Addressable RGB LED strips (5V/Data/Ground) with the maximum power rating of 3A

(5V). In the case of 20% brightness, the connector supports up to 200 LEDs.

∙

Always turn off the power supply and unplug the power cord from the power outlet

before installing or removing the RGB LED strip.

∙

Please use MSI’s software to control the extended LED strip.

JRAINBOW1~2: Addressable RGB LED connectors

The JRAINBOW connectors allow you to connect the WS2812B Individually

Addressable RGB LED strips 5V.

JRAINBOW

connector

JRAINBOW connector

System Fan connector

Rainbow RGB LED

extension cable WS2812B Individually

Addressable RGB LED strips 5V

Addressable RGB LED Strip Connection

Addressable RGB LED Fan Connection

Addressable RGB LED Fan

JRAINBOW2 1

JRAINBOW1

1 +5V 2 Data

3 No Pin 4 Ground

Overview of Components

JCORSAIR1: CORSAIR Connector

The JCORSAIR1 connector allows you to connect the CORSAIR Individually

Addressable Lighting PRO RGB LED strips 5V or CORSAIR RGB fans with the CORSAIR

fan hub. Once all items are connected properly, you can control the CORSAIR RGB

LED strips and fans with MSI's software.

1 +5V 2 Data

3 Ground

CORSAIR RGB Fan Connection

⚠

Important

∙

Fans must start at 1 and continue in series. 1 > 2 > 3 > 4 > 5 > 6. Any fan not

connected in series will break communication and the RGB LED lighting function will

not work.

∙

Quantity of RGB LED Fans or RGB LED Lighting PRO strips supported may differ

between models. Please refer to the motherboard specification.

∙

CORSAIR RGB LED Fan and CORSAIR Lighting Node PRO can’t be used at the same

time.

JCORSAIR1 connector

SYS_FAN

SYS_FAN SYS_FAN

SYS_FAN

JCORSAIR1 connector

SATA power

CORSAIR Lighting Node PRO Connection

CORSAIR RGB LED fan

CORSAIR fan hub

54 Onboard LEDs

EZ Debug LED

These LEDs indicate the debug status of the motherboard.

CPU - indicates CPU is not detected or fail.

DRAM - indicates DRAM is not detected or fail.

VGA - indicates GPU is not detected or fail.

BOOT - indicates the booting device is not detected

or fail.

Onboard LEDs

JPWRLED1: LED power input

This connector is used by retailers to demonstrate onboard LED lights.

JPWRLED1 - LED power input

LED_SW1: EZ LED Control

This switch is used to switch on/ off all the LEDs of motherboard.

LED_SW1

LED_OFF LED_ON

(Default)

Onboard LEDs

Debug Code LED

The Debug Code LED displays progress and error codes during and after POST. Refer

to the Debug Code LED table for details.

Hexadecimal Character Table

Hexadecimal 0 1 2 3 4 5 6 7 8 9 A B C D E F

Debug Code

LED display 0123456789ABCDEF

Boot Phases

Security (SEC) – initial low-level initialization

Pre-EFI Initialization (PEI) – memory initialization

Driver Execution Environment (DXE) – main hardware initialization

Boot Device Selection (BDS) – system setup, pre-OS user interface & selecting a

bootable device (CD/DVD, HDD, USB, Network, Shell, …)

Debug Code LED Table

SEC Progress Codes

01 Power on. Reset type detection (soft/hard)

02 AP initialization before microcode loading

03 System Agent initialization before microcode loading

04 PCH initialization before microcode loading

06 Microcode loading

07 AP initialization after microcode loading

08 System Agent initialization after microcode loading

09 PCH initialization after microcode loading

0B Cache initialization

56 Onboard LEDs

SEC Error Codes

0C - 0D Reserved for future AMI SEC error codes

0E Microcode not found

0F Microcode not loaded

PEI Progress Codes

10 PEI Core is started

11 Pre-memory CPU initialization is started

12 - 14 Pre-memory CPU initialization (CPU module specific)

15 Pre-memory System Agent initialization is started

16 - 18 Pre-Memory System Agent initialization (System Agent module specific)

19 Pre-memory PCH initialization is started

1A - 1C Pre-memory PCH initialization (PCH module specific)

2B Memory initialization. Serial Presence Detect (SPD) data reading

2C Memory initialization. Memory presence detection

2D Memory initialization. Programming memory timing information

2E Memory initialization. Configuring memory

2F Memory initialization (other)

31 Memory Installed

32 CPU post-memory initialization is started

33 CPU post-memory initialization. Cache initialization

34 CPU post-memory initialization. Application Processor(s) (AP) initialization

35 CPU post-memory initialization. Boot Strap Processor (BSP) selection

36 CPU post-memory initialization. System Management Mode (SMM) initialization

37 Post-Memory System Agent initialization is started

38 - 3A Post-Memory System Agent initialization (System Agent module specific)

3B Post-Memory PCH initialization is started

3C - 3E Post-Memory PCH initialization (PCH module specific)

4F DXE IPL is started

PEI Error Codes

4B Memory not installed (For Summit CPU)

E0 Memory not installed (For Bristol CPU)

DXE Progress Codes

60 DXE Core is started

61 NVRAM initialization

62 Installation of the PCH Runtime Services

63 CPU DXE initialization is started

64 - 67 CPU DXE initialization (CPU module specific)

Onboard LEDs

68 PCI host bridge initialization

69 System Agent DXE initialization is started

6A System Agent DXE SMM initialization is started

6B - 6F System Agent DXE initialization (System Agent module specific)

70 PCH DXE initialization is started

71 PCH DXE SMM initialization is started

72 PCH devices initialization

73 - 77 PCH DXE Initialization (PCH module specific)

78 ACPI module initialization

79 CSM initialization

7A - 7F Reserved for future AMI DXE codes

90 Boot Device Selection (BDS) phase is started

91 Driver connecting is started

92 PCI Bus initialization is started

93 PCI Bus Hot Plug Controller Initialization

94 PCI Bus Enumeration 32

95 PCI Bus Request Resources

96 PCI Bus Assign Resources

97 Console Output devices connect

98 Console input devices connect

99 Super IO Initialization

9A USB initialization is started

9B USB Reset

9C USB Detect

9D USB Enable

9E -9F Reserved for future AMI codes

A0 IDE initialization is started

A1 IDE Reset

A2 IDE Detect

A3 IDE Enable

A4 SCSI initialization is started

A5 SCSI Reset

A6 SCSI Detect

A7 SCSI Enable

A8 Setup Verifying Password

A9 Start of Setup

AB Setup Input Wait

AD Ready To Boot event

AE Legacy Boot event

AF Exit Boot Services event

58 Onboard LEDs

B0 Runtime Set Virtual Address MAP Begin

B1 Runtime Set Virtual Address MAP End

B2 Legacy Option ROM Initialization

B3 System Reset

B4 USB hot plug

B5 PCI bus hot plug

B6 Clean-up of NVRAM

B7 Configuration Reset (reset of NVRAM settings)

B8 - BF Reserved for future AMI codes

DXE Error Codes

D0 CPU initialization error

D1 System Agent initialization error

D2 PCH initialization error

D3 Some of the Architectural Protocols are not available

D4 PCI resource allocation error. Out of Resources

D5 No Space for Legacy Option ROM

D6 No Console Output Devices are found

D7 No Console Input Devices are found

D8 Invalid password

D9 Error loading Boot Option (LoadImage returned error)

DA Boot Option is failed (StartImage returned error)

DB Flash update is failed

DC Reset protocol is not available

S3 Resume Progress Codes

E0 S3 Resume is stared (S3 Resume PPI is called by the DXE IPL)

E1 S3 Boot Script execution

E2 Video repost

E3 OS S3 wake vector call

E4 - E7 Reserved for future AMI progress codes

S3 Resume Error Codes

E8 S3 Resume Failed

E9 S3 Resume PPI not Found

EA S3 Resume Boot Script Error

EB S3 OS Wake Error

EC - EF Reserved for future AMI error codes

Onboard LEDs

Recovery Progress Codes

F0 Recovery condition triggered by firmware (Auto recovery)

F1 Recovery condition triggered by user (Forced recovery)

F2 Recovery process started

F3 Recovery firmware image is found

F4 Recovery firmware image is loaded

F5 - F7 Reserved for future AMI progress codes

Recovery Error Codes

F8 Recovery PPI is not available

F9 Recovery capsule is not found

FA Invalid recovery capsule

FB - FF Reserved for future AMI error codes

ACPI States Codes

The following codes appear after booting and the operating system into ACPI modes.

01 System is entering S1 sleep state

02 System is entering S2 sleep state

03 System is entering S3 sleep state

04 System is entering S4 sleep state

05 System is entering S5 sleep state

10 System is waking up from the S1 sleep state

20 System is waking up from the S2 sleep state

30 System is waking up from the S3 sleep state

40 System is waking up from the S4 sleep state

AC System has transitioned into ACPI mode. Interrupt controller is in PIC mode.

AA System has transitioned into ACPI mode. Interrupt controller is in APIC mode.

60 Installing OS, Drivers & MSI Center

Installing OS, Drivers & MSI Center

Please download and update the latest utilities and drivers at www.msi.com

Installing Windows® 10

1. Power on the computer.

2. Insert the Windows® 10 installation disc/USB into your computer.

3. Press the Restart button on the computer case.

4. Press F11 key during the computer POST (Power-On Self Test) to get into Boot

Menu.

5. Select the Windows® 10 installation disc/USB from the Boot Menu.

6. Press any key when screen shows Press any key to boot from CD or DVD...

message.

7. Follow the instructions on the screen to install Windows® 10.

Installing Drivers

1. Start up your computer in Windows® 10.

2. Insert MSI® USB Drive into the USB port.

3. Click the Select to choose what happens with this disc pop-up notification, then

select Run DVDSetup.exe to open the installer. If you turn off the AutoPlay feature

from the Windows Control Panel, you can still manually execute the DVDSetup.exe

from the root path of the MSI USB Drive.

4. The installer will find and list all necessary drivers in the Drivers/Software tab.

5. Click the Install button in the lower-right corner of the window.

6. The drivers installation will then be in progress, after it has finished it will prompt

you to restart.

7. Click OK button to finish.

8. Restart your computer.

MSI Center

MSI Center is an application that helps you easily optimize game settings and smoothly

use content creation softwares. It also allows you to control and synchronize LED

light effects on PCs and other MSI products. With MSI Center, you can customize ideal

modes, monitor system performance, and adjust fan speed.

MSI Center User Guide

If you would like to know more information about MSI Center, please

refer to

http://download.msi.com/manual/mb/MSICENTER.pdf

or scan the QR code to access.

⚠

Important

Functions may vary depending on the product you have.

UEFI BIOS

MSI UEFI BIOS is compatible with UEFI (Unified Extensible Firmware Interface)

architecture. UEFI has many new functions and advantages that traditional BIOS

cannot achieve, and it will completely replace BIOS in the future. The MSI UEFI

BIOS uses UEFI as the default boot mode to take full advantage of the new chipset’s

capabilities.

⚠

Important

The term BIOS in this user guide refers to UEFI BIOS unless otherwise noted.

UEFI advantages

∙Fast booting - UEFI can directly boot the operating system and save the BIOS self-

test process. And also eliminates the time to switch to CSM mode during POST.

∙Supports for hard drive partitions larger than 2 TB.

∙Supports more than 4 primary partitions with a GUID Partition Table (GPT).

∙Supports unlimited number of partitions.

∙Supports full capabilities of new devices - new devices may not provide backward

compatibility.

∙Supports secure startup - UEFI can check the validity of the operating system to

ensure that no malware tampers with the startup process.

Incompatible UEFI cases

∙32-bit Windows operating system - this motherboard supports only Windows 10

64-bit operating system.

∙Older graphics card - the system will detect your graphics card. When display a

warning message There is no GOP (Graphics Output protocol) support detected in

this graphics card.

⚠

Important

We recommend that you to replace with a GOP/UEFI compatible graphics card or

using integrated graphics from CPU for having normal function.

How to check the BIOS mode?

1. Power on your computer.

2. Press Delete key, when the Press DEL key to enter Setup Menu, F11 to enter

Boot Menu message appears on the screen during the boot process.

3. After entering the BIOS, you can check the BIOS Mode at the top of the screen.

BIOS Mode: UEFI

62 BIOS Setup

BIOS Setup

The default settings offer the optimal performance for system stability in normal

conditions. You should always keep the default settings to avoid possible system

damage or failure booting unless you are familiar with BIOS.

⚠

Important

∙

BIOS items are continuously update for better system performance. Therefore, the

description may be slightly different from the latest BIOS and should be for reference

only. You could also refer to the HELP information panel for BIOS item description.

∙

The pictures in this guide are for reference only .

∙

The BIOS screens, options and settings will vary depending on your system.

Entering BIOS Setup

Press Delete key, when the Press DEL key to enter Setup Menu, F11 to enter Boot

Menu message appears on the screen during the boot process.

Function key

F1: General Help list

F2: Add/ Remove a favorite item

F3: Enter Favorites menu

F4: Enter CPU Specifications menu

F5: Enter Memory-Z menu

F6: Load optimized defaults

F7: Switch between Advanced mode and EZ mode

F8: Load Overclocking Profile

F9: Save Overclocking Profile

F10: Save Change and Reset*

F12: Take a screenshot and save it to USB flash drive (FAT/ FAT32 format only).

Ctrl+F: Enter Search page

* When you press F10, a confirmation window appears and it provides the modification

information. Select between Yes or No to confirm your choice.

BIOS User Guide

If you’d like to know more instructions on setting up the BIOS, please

refer to

http://download.msi.com/manual/mb/AMDX570BIOS.pdf

or scan the QR code to access.

BIOS Setup

Resetting BIOS

You might need to restore the default BIOS setting to solve certain problems. There

are several ways to reset BIOS:

∙Go to BIOS and press F6 to load optimized defaults.

∙Short the Clear CMOS jumper on the motherboard.

∙Press the Clear CMOS button on the rear I/O panel. (optional)

⚠

Important

Be sure the computer is off before clearing CMOS data. Please refer to the Clear

CMOS section for resetting BIOS.

Updating BIOS

Updating BIOS with M-FLASH

Before updating:

Please download the latest BIOS file that matches your motherboard model from MSI

website. And then save the BIOS file into the USB flash drive.

Updating BIOS:

1. Switch to the target BIOS ROM by Multi-BIOS switch. If your motherboard does not

has this switch , please skip this step.

2. Insert the USB flash drive that contains the update file into the USB port.

3. Please refer the following methods to enter flash mode.

▪Reboot and press Ctrl + F5 key during POST and click on Yes to reboot the

system.

Press <Ctrl+F5> to activate M-Flash for BIOS update.

▪Reboot and press Del key during POST to enter BIOS. Click the M-FLASH button

and click on Yes to reboot the system.

4. Select a BIOS file to perform the BIOS update process.

5. When prompted click on Yes to start recovering BIOS.

6. After the flashing process is 100% completed, the system will reboot

automatically.

64 BIOS Setup

Updating the BIOS with MSI Center

Before updating:

∙Make sure the LAN driver is already installed and the internet connection is set

properly.

∙Please close all other application software before updating the BIOS.

To update BIOS:

1. Install and launch MSI Center and go to Support page.

2. Select Live Update and click on Advance button.

3. Select the BIOS file and click on Install button.

4. The installation reminder will appear, then click the Install button on it.

5. The system will automatically restart to update BIOS.

6. After the flashing process is 100% completed, the system will restart

automatically.

Updating BIOS with Flash BIOS Button (optional)

1. Please download the latest BIOS file that matches your motherboard model from

the MSI® website.

2. Rename the BIOS file to MSI.ROM, and save it to the root of the USB 2.0 storage

device.

3. Connect the power supply to CPU_PWR1 and ATX_PWR1. (No need to install CPU

and memory.)

4. Plug the USB 2.0 storage device that contains the MSI.ROM file into the Flash

BIOS Port on the rear I/O panel.

5. Press the Flash BIOS Button to flash BIOS, and the LED starts flashing.

6. The LED will be turned off when the process is completed.

Nahimic 3

Nahimic 3 is designed to offer the best audio experience it contains audio effects,

microphone effects and Sound Tracker.

Installation and Update

Nahimic 3 is included in the audio driver. If you need to install it or update it, please

use the Driver Disc with your motherboard or download the driver from MSI’s official

website.

Audio Tab

From this tab, you can access all of Nahimic 3’s audio effects, audio profiles and

settings.

Audio

Profiles

Audio Effects

Reset Button

Try Button

On/Off Button

Device display & Volume

∙Device display & Volume - displays the type of audio device currently being used as

output, as well as its current volume.

▪Mute - mutes the current audio output device.

∙Audio profiles - allows you to choose between 4 factory audio profiles to fit your

multimedia experience (Music, Gaming, Movie or Communication). All profiles can be

modified as you wish.

∙On/Off Button - allows you to turn all of Nahimic 3’s audio effects in one click.

∙Audio Effects - allows you to separately control any of the 5 audio effects.

▪Surround Sound - it is an audio effect mainly dedicated to headphones acoustic

experience.

▫Gaming and Movies - virtualizes the multichannel audio stream from the

game engine or the movie soundtrack and downmixes it in order to retrieve a

multichannel listening experience over your stereo headphones or speakers.

▫Music - expands the stereo for a wider sound stage.

▪Volume Stabilizer - it maintains a constant volume for all elements of the

audio experience (dialogs, soundtrack, explosions, etc.) to make them all sound

softer, balanced or louder. The Quiet On / Off option allows to enter a night mode

by removing some basses. This way, you won’t disturb people around you if you’re

using speakers to play your media.

66 Nahimic 3

▪Voices - it boosts (or removes) the speech in movies, video games and incoming

communication from -12 to +12 dB.

▪Bass - increases (or decreases) the energy in low frequencies from -12 to +12

dB.

▪Treble - increases (or decreases) the energy in high frequencies from -12 to +12

dB.

∙Reset Button - restores the current profile to its default values.

∙Try Button - launches an audio sample that allows to test audio settings.

Microphone Tab

From this tab, you can access all of Nahimic 3’s microphone effects and settings.

Microphone

Profiles

Microphone

Effects

Reset Button

Try Button

On/Off Button

Device display & Volume

∙Device display and volume - displays the type of recording device currently being

used as input, as well as its current volume.

▪Mute - mutes the current mic device.

∙Mic profiles - allows you to choose between 2 factory mic profiles to fit your

experience (Chat or Conference). All profiles can be modified as you wish.

∙On / Off button - allows you to turn on and off all Nahimic 3’s microphone effects in

one click.

∙Microphone Effects - allows you to separately control any of the 4 microphone

effects.

▪Static Noise Suppression - it removes the static noises like the ones coming

from your computer fans.

▪Echo Cancellation - improves the voice quality by cancelling the echo.

▪Lateral Sound Cancellation - it only records the sound coming from the front of

your microphone.

▪Voice Stabilizer - Levels the volume of your voice in order to avoid any saturation

and maintains a constant and clear communication.

∙Reset Button - restores the current profile to its default values.

∙Try Button - Turns the microphone loopback On/Off.

Nahimic 3

Sound Tracker Tab

The Sound Tracker is an FPS oriented feature that provides a visual indication

localizing the sources of the sounds while in a game. These are represented by

dynamic segments pointing the direction of the sounds: the more opaque they are,

the stronger the sounds are. Thanks to this feature, players are able to pick up an

approaching threat more definitively and easily, thereby being even more dynamic.

The Sound Tracker captures the 5.1 and 7.1 sound streams processed by your audio

system, and is displayed in the applications and games using DirectX 9, 9c, 10 and 11.

Sound Tracker

Effects

Sound Tracker

Compatible

games

Try ButtonOn/Off Button

∙ON / OFF Button - allows you to enable/ disable the Sound Tracker by switching this

option ON/ OFF.

∙Try Button - launch a 7.1 audio sample allowing you to preview how the radar will

react in your game.

∙Sound Tracker Effects

▪Size - allows you to adjust the scale of the Sound Tracker, making it look bigger

or smaller.

▪Transparency - allows you to adjust the transparency of the Sound Tracker,

making it look more or less discrete.

▪Color - click the colored circle to open the color edition window. You can apply

the color you want to the dynamic segments.

∙Compatible games - clicking this link opens the official Nahimic website, and leads

to the list of compatible games able to display the Sound Tracker.

Settings Tab

In this section, it allows you to select the language of Nahimic 3’s UI.

RAID Configuration

The introduction of RAID levels and types are as below:

RAID 0 breaks the data into blocks which are written to separate hard drives.

Spreading the hard drive I/O load across independent channels greatly

improves I/O performance.

RAID 1 provides data redundancy by mirroring data between the hard drives and

provides enhanced read performance.

RAID 10 uses four hard drives to create a combination of RAID 0 and 1 by forming a

RAID 0 array from two RAID 1 arrays.

RAID level comparison

RAID 0 RAID 1 RAID 10

Minimum # drives 2 2 4

Data protection None Excellent Excellent

Read performance Excellent OK OK

Write performance Excellent Good Good

Capacity utilization 100% 50% 50%

⚠

Important

All the information/ volumes/ pictures listed in your system might differ from the

illustrations in this appendix.

AMD RAID User Guide

If you’d like to know more instructions on how to set up AMD RAID,

please refer to

http://download.msi.com/manual/mb/AMDRAID.pdf

or scan the QR code to access.

68 RAID Configuration

Troubleshooting

Before sending the motherboard for RMA

repair, try to go over troubleshooting

guide first to see if your got similar

symptoms as mentioned below.

The power is not on.

∙Connect the AC power cord to an

electrical outlet securely.

∙Check if all ATX power connectors

like ATX_PWR1, CPU_PWR1 are

connected from the power supply to the

motherboard?

∙Some power supply units have a power

button on the rear side, make sure the

button is turned on.

∙Check if the power switch cable is

connected to JFP1 pin header properly.

∙Verify the Clear CMOS jumper JBAT1 is

set to Keep DATA.

∙Test with another known working

power supply of equal or greater

wattage.

The power is on, but no signal to

monitor

∙Connect the monitor power cord to a

electrical outlet securely.

∙Make sure the monitor is turned on.

∙Select different inputs on the monitor.

∙If 3 long beeps are heard, remove all

memory modules and try to install only

one memory module in the DIMMA2 slot

first and then restart the computer.

∙If 1 long 2 short beeps are heard,

remove and reinstall the graphics card

and then restart the computer.

∙Test with another known working

graphics card.

The computer does not boot after

updating the BIOS

∙Clear the CMOS.

∙Use the secondary BIOS to bootup the

system (Only for motherboard with Dual

BIOS)

Lost BIOS password

∙Clear the CMOS, but that will cause

you to lose all customized settings in the

BIOS.

There is no audio

∙Adjust the volume.

∙Connect the speakers/headphones to

audio ports on the motherboard rear IO

panel.

∙Remove secondary speakers/

headphones, HDMI cables, USB audio

devices.

∙Test with another known working

speaker or headphone.

There is no network

∙Make sure the network chipset driver

has been installed.

∙Verify if the network cable is properly

connected and make sure the LAN port

LEDs are properly illuminated.

∙Verify your TCP/IP settings.

∙Restart or reset your router.

∙Test with another known working LAN

cable.

The USB device is not working

∙Make sure your USB drive driver has

been installed.

∙Verify if USB device is listed in

Windows® Device Manager.

∙Connect the USB device to other USB

port on the motherboard rear IO panel.

Troubleshooting

NOTE

70 Troubleshooting

Regulatory Notices

FCC Compliance Statement

Note: This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

yReorient or relocate the receiving antenna.

yIncrease the separation between the equipment

and receiver.

yConnect the equipment into an outlet on a circuit

different from that to which the receiver is

connected.

yConsult the dealer or an experienced radio/TV

technician for help.

Caution: Changes or modifications not expressly

approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

Tested to comply with FCC standards

FOR HOME OR OFFICE USE

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation.

CE Conformity

Products bearing the CE marking comply

with one or more of the following EU

Directives as may be applicable:

RED 2014/53/EU; Low Voltage Directive 2014/35/EU;

EMC Directive 2014/30/EU; RoHS Directive 2011/65/EU.

Compliance with these directives is assessed using

applicable European Harmonized Standards.

The point of contact for regulatory matters is MSI,

MSI-NL Eindhoven 5706 5692 ER Son.

KC인증서

󻺳󽐪󼛮󼏒󼏂󼂖󼌶󼕦󼵆󻞞󼌶

󼘎󽉺󻡷󻡆󼕪󻫦󻋎

󻢚󻅪󻡷

󼘎󼙢󺼶󼓆󺼶

󼘎󼙢󼖂󻨁󼘎󼙢󺭟󺧲󼜃󺭟

クラスB情報技術装置

󸅗󶹌󾖛󽚵󳞹󲝅󳫒󸂓󸅗󶹌󾖜

󸅗󶹌󾖛󲺟󳐑󵩫󲟓󱣎󵭡󵺅󵷜

    󾖛  󸅗 󶹌           

󲀰󱥰󴡉󸶀󳲞󱣎󵭡󾖛󲀰󱥰󹦟󲺗󳓜󸦕

󾖜󲀮󾉣󸔆󴃬󴉩󳗂󴨟󲀮󾉣

  󱚘  󾖜

VCCI-B

C-Tick Compliance

Battery Information

European Union:

Batteries, battery packs, and

accumulators should not be disposed of as

unsorted household waste. Please use the

public collection system to return, recycle,

or treat them in compliance with the local

regulations.

Taiwan:

󳑿󹩚󴯶󸕂󲔴󳽴

For better environmental protection,

waste batteries should be collected

separately for recycling or special

disposal.

California, USA:

The button cell battery may contain

perchlorate material and requires special

handling when recycled or disposed of in

California.

For further information please visit:

http://www.dtsc.ca.gov/hazardouswaste/perchlorate/

CAUTION: There is a risk of explosion, if battery is

incorrectly replaced.

Replace only with the same or equivalent type

recommended by the manufacturer.

Chemical Substances Information

In compliance with chemical substances regulations,

such as the EU REACH Regulation (Regulation EC

No. 1907/2006 of the European Parliament and the

Council), MSI provides the information of chemical

substances in products at:

https://storage-asset.msi.com/html/popup/csr/

evmtprtt_pcm.html

Environmental Policy

yThe product has been designed to

enable proper reuse of parts and

recycling and should not be thrown

away at its end of life.

yUsers should contact the local

authorized point of collection for recycling and

disposing of their end-of-life products.

yVisit the MSI website and locate a nearby distributor

for further recycling information.

yUsers may also reach us at gpcontdev@msi.com for

information regarding proper Disposal, Take-back,

Recycling, and Disassembly of MSI products.

WEEE (Waste Electrical and

Electronic Equipment) Statement

ENGLISH

To protect the global environment and as

an environmentalist, MSI must remind

you that...

Under the European Union (“EU”) Directive

on Waste Electrical and Electronic

Equipment, Directive 2002/96/EC, which

takes effect on August 13, 2005, products

of “electrical and electronic equipment”

R-R-MSI-10-7D50

ii Regulatory Notices

cannot be discarded as municipal wastes anymore, and

manufacturers of covered electronic equipment will

be obligated to take back such products at the end of

their useful life. MSI will comply with the product take

back requirements at the end of life of MSI-branded

products that are sold into the EU. You can return

these products to local collection points.

DEUTSCH

Hinweis von MSI zur Erhaltung und Schutz unserer

Umwelt

Gemäß der Richtlinie 2002/96/EG über Elektro- und

Elektronik-Altgeräte dürfen Elektro- und Elektronik-

Altgeräte nicht mehr als kommunale Abfälle entsorgt

werden. MSI hat europaweit verschiedene Sammel-

und Recyclingunternehmen beauftragt, die in die

Europäische Union in Verkehr gebrachten Produkte,

am Ende seines Lebenszyklus zurückzunehmen.

Bitte entsorgen Sie dieses Produkt zum gegebenen

Zeitpunkt ausschliesslich an einer lokalen

Altgerätesammelstelle in Ihrer Nähe.

FRANÇAIS

En tant qu’écologiste et afin de protéger

l’environnement, MSI tient à rappeler ceci...

Au sujet de la directive européenne (EU) relative aux

déchets des équipement électriques et électroniques,

directive 2002/96/EC, prenant effet le 13 août 2005, que

les produits électriques et électroniques ne peuvent

être déposés dans les décharges ou tout simplement

mis à la poubelle. Les fabricants de ces équipements

seront obligés de récupérer certains produits en fin

de vie. MSI prendra en compte cette exigence relative

au retour des produits en fin de vie au sein de la

communauté européenne. Par conséquent vous pouvez

retourner localement ces matériels dans les points

de collecte.

РУССКИЙ







































ESPAÑOL

MSI como empresa comprometida con la protección

del medio ambiente, recomienda:

Bajo la directiva 2002/96/EC de la Unión Europea

en materia de desechos y/o equipos electrónicos,

con fecha de rigor desde el 13 de agosto de 2005,

los productos clasificados como “eléctricos y

equipos electrónicos” no pueden ser depositados

en los contenedores habituales de su municipio, los

fabricantes de equipos electrónicos, están obligados

a hacerse cargo de dichos productos al termino de

su período de vida. MSI estará comprometido con los

términos de recogida de sus productos vendidos en

la Unión Europea al final de su periodo de vida. Usted

debe depositar estos productos en el punto limpio

establecido por el ayuntamiento de su localidad o

entregar a una empresa autorizada para la recogida de

estos residuos.

NEDERLANDS

Om het milieu te beschermen, wil MSI u eraan

herinneren dat….

De richtlijn van de Europese Unie (EU) met betrekking

tot Vervuiling van Electrische en Electronische

producten (2002/96/EC), die op 13 Augustus 2005 in

zal gaan kunnen niet meer beschouwd worden als

vervuiling. Fabrikanten van dit soort producten worden

verplicht om producten retour te nemen aan het

eind van hun levenscyclus. MSI zal overeenkomstig

de richtlijn handelen voor de producten die de

merknaam MSI dragen en verkocht zijn in de EU. Deze

goederen kunnen geretourneerd worden op lokale

inzamelingspunten.

SRPSKI





vas podesti da…





EC, koja stupa na snagu od 13. Avgusta 2005, proizvodi











proizvoda kojima je istekao vek trajanja, koji imaju MSI



vratiti na lokalnim mestima za prikupljanje.

POLSKI







odpadów produktów elektrycznych i elektronicznych















(sprzedawane na terenie Unii Europejskiej) wycofywane



wyznaczonych punktach zbiorczych.

TÜRKÇE



























iii

Regulatory Notices

ČESKY









EC platné od 13. srpna 2005 je zakázáno likvidovat



komunálním odpadu a výrobci elektronických













MAGYAR

Annak érdekében, hogy környezetünket megvédjük,



Önt, hogy ...

Az Európai Unió („EU”) 2005. augusztus 13-án hatályba



hulladékairól szóló 2002/96/EK irányelve szerint

az elektromos és elektronikus berendezések



és az ilyen elektronikus berendezések gyártói

kötelessé válnak az ilyen termékek visszavételére

azok hasznos élettartama végén. Az MSI betartja a

termékvisszavétellel kapcsolatos követelményeket

az MSI márkanév alatt az EU-n belül értékesített

termékek esetében, azok élettartamának végén. Az



ITALIANO

Per proteggere l’ambiente, MSI, da sempre amica della

natura, ti ricorda che….

In base alla Direttiva dell’Unione Europea (EU) sullo

Smaltimento dei Materiali Elettrici ed Elettronici,

Direttiva 2002/96/EC in vigore dal 13 Agosto 2005,

prodotti appartenenti alla categoria dei Materiali

Elettrici ed Elettronici non possono più essere eliminati

come rifiuti municipali: i produttori di detti materiali

saranno obbligati a ritirare ogni prodotto alla fine

del suo ciclo di vita. MSI si adeguerà a tale Direttiva

ritirando tutti i prodotti marchiati MSI che sono stati

venduti all’interno dell’Unione Europea alla fine del

loro ciclo di vita. È possibile portare i prodotti nel più

vicino punto di raccolta

日本JIS C 0950材質宣言

󴂬󴋉󳋌󴚄󸋮󴑸󾖛󳎧󴊆󴂬󱟧󹤒󸡯

󲢔󵛚󲹥󱴹󹆣󹩚󴮅󹩚󲷍󴡉󲑠󾖛󸇆󸹈

󶽳󲂳󴊈󵛃󸣚󸂱󶈾󶺳󱺅󱟔󾖜

https://storage-asset.msi.com/html/popup/csr/

cemm_jp.html

India RoHS

This product complies with the “India E-waste

(Management and Handling) Rule 2011” and prohibits

use of lead, mercury, hexavalent chromium,

polybrominated biphenyls or polybrominated diphenyl

ethers in concentrations exceeding 0.1 weight % and

0.01 weight % for cadmium, except for the exemptions

set in Schedule 2 of the Rule.

Türkiye EEE yönetmeliği



Україна обмеження на наявність

небезпечних речовин











Việt Nam RoHS











Wireless Radio Use

This device is restricted to indoor use when operating

in the 2.4GHz, 5GHz frequency band.

Cet appareil doit être utilisé à l’intérieur.

󻃫󽍦󻤦󻼒󻼖󻰶󻂆󼒦󼒛󼜃󼗶󽃾󽐮󼃒󺧲󻂗󻼣󼕦󼕺󼔾

󸇆󲆛󾖛󲄔󴲾󳿌󳌶󲚺󱹿󱢖

󾖛󲾯󱱟󱣎󵭡󲁗󷅯󾖜

NCC無線設備警告聲明

󳋌󱢖󹲡󵢋󸒎󹲡󴫓󹤗󴁘󲹸󱰭󱣎󵭡󾖜

󶬈󲘻󳓑󸓆󸙒󲁺󴑸󱛷󱢀󱸪󵢋󲼽󹲡󹩚󴡉󾖞󹬰󶬈󸐎󲁗󾖞󱰻󲁤󾖛󲉦

󷵏󳨘󱣎󵭡󶽳󲗗󱚚󳗈󳺖󷍬󸛚󴉣󹲡󵢋󾖛󱸬󲣴󱸪󵢋󳨘󸛚󴉣󱿖󸐈

󸎽󱛷󵛚󳚱󲀟󱸪󷅯󾖜

󱢀󱸪󵢋󲼽󹲡󹩚󴡉󱛷󱣎󵭡󱚚󳗈󳖋󹱄󹶗󷏹󲹂󾆈󲀟󳎥󳼄󲁺󴲥󸸶

󱥰󽚮󶬈󵷒󵤱󴊈󳎥󳼄󵤱󸟱󴄼󾖞󳦔󶕌󱾔󱩆󵭡󾖞󱚿󳽺󲋉󷍿󵐦󳎥󳼄󴄼

󴁔󳗈󶳶󶴙󱣎󵭡󾖜󱶝󹱎󲁺󴲥󸸶󱥰󾖞󳮜󱤀󹩚󱥰󴲥󸋮󲹥󱢖󴚄󱛷󵐦

󶮥󹩚󸸶󱥰󾖜󱢀󱸪󵢋󲼽󹲡󹩚󴡉󹱑󳘢󲀰󲁺󴲥󸸶󱥰󳨘󳋌󴚄󾖛󶍔󲸜

󲀟󹅘󵵢󵭡󹩚󴲾󸱺󲼽󳚱󹩚󴡉󸐈󱪸󱛷󳎥󳼄󾖜

Products with radio functionality (EMF)

This product incorporates a radio transmitting

and receiving device. For computers in normal

use, a separation distance of 20 cm ensures that

radio frequency exposure levels comply with EU

requirements. Products designed to be operated

at closer proximities, such as tablet computers,

comply with applicable EU requirements in typical

operating positions. Products can be operated without

maintaining a separation distance unless otherwise

indicated in instructions specific to the product.

Restrictions for products with radio functionality

CAUTION: IEEE 802.11x wireless LAN with

5.15–5.35 GHz frequency band is restricted

for indoor use only in all European Union

member states, EFTA (Iceland, Norway,

Liechtenstein), and most other European countries

(e.g., Switzerland, Turkey, Republic of Serbia).

Using this WLAN application outdoors might lead to

interference issues with existing radio services.

Radio frequency bands and maximum power levels

Features :802.11 a/b/g/n/ac/ax, BT

Frequency Range :2.4GHz, 5GHz, 6GHz

Modulation :FHSS, DSSS, OFDM

Power Output :10, 20, 23

Channel Band Width :1, 5, 20 ,40 , 80MHz

iv Regulatory Notices

MS-7D50主板产品中有害物质的名称及含量

󸿬󱠁󲂁󶎊

󴊈󲺗󵛃󸤼

󹜱

(Pb)

󴯳

(Hg)

󹞵

(Cd)

󱰽󱠃󹝘

(Cr(VI))

󲣙󴾨󷀐󷖪

(PBB)

󲣙󴾨󱝗󷖪󹄲

(PBDE)

󱾏󱵼󵭳󸩃󴍆󶵪󱠁      

󵭳󴯶      

󲣏󸿬󱥰󲁣󸶚󳲞󲤆      

󶵥󴌂      

󴋉󸂱󴑸󱤀󳰼󵷜󸍂󲹥󶶼󱵺󾖜

󸂱󶈾󸝎󴊈󲺗󵛃󸤼󲖬󸝎󸿬󱠁󳩢󴊈󲗗󸤼󴌂󴀖󱛉󵷜󲂳󹆤󲗗󲖬󸍂󲹥󵷜󹤗󹆤󸋘󴯄󱟧󱚘󾖜

󸂱󶈾󸝎󴊈󲺗󵛃󸤼󷍿󲽕󲖬󸝎󸿬󱠁󵷜󴏉󱚋󲗗󸤼󴌂󴀖󱛉󵷜󲂳󹆤󸦨󱴤󸍂󲹥󵷜󹤗󹆤󸋘󴯄󾖞󱡲󳩢󴊈󸿬󱠁󹀎󶗼󲁺

󴦱󵹩󸋘󴯄󾖜

󱾏󱵼󵭳󸩃󴍆󶵪󱠁󱻏󳭱󱾏󱵼󵭳󸩃󴍆󲀟󱱊󴍐󳨑󵷜󹩏󸿬󱠁󾖜

󵭳󴯶󴋉󱢈󱚗󲦚󴊈󵣄󱥧󱣎󵭡󴊱󹤗󴐟󸜯󾖞󱟧󴋉󱢈󴐟󸜯󱛝󱛞󾖜

󱚗󸷈󴊈󴬐󴊈󲺗󵛃󸤼󳨘󱯯󶨫󴺆󱽤󱠸󱤀󲘻󲁣󱛷󸿬󱠁󳋘󳒺󶾀󴊈󳩢󲠂󱳝󾖜

󱞅󲆛󸿬󱠁󴋉󱢈󱚗󲦚󴊈󵣄󱥧󱣎󵭡󴊱󹤗󴐟󸜯󾖞󱟧󴋉󱢈󴐟󸜯󱛝󱛞󾖜

限用物質含有情況標示聲明書

󸐈󱪷󲂀󶏺󾖠󹩙󷉄󱛞󴡈󴍇 󲘻󷵎󲘻󳓑󾖠

󲌖󱯯

󹤗󵭡󵛃󸣚󲀟󱱊󱻯󲸜󶗼󷵏

󹊰

(Pb)

󴯳

(Hg)

󹔜

(Cd)

󱰽󱭪󹋬

(Cr+6)

󲣙󴾨󷁆󷖪

(PBB)

󲣙󴾨󱝗󷖪󹄲

(PBDE)

󹩚󸩃󴍆      

󹩚󲷍󱯯󱠁      

󹆨󲿦󴡉󴜷󱠁      

󲝺󷋇󴡉󴜷󱠁      

󱪸󶽰󸦨󱴤󲀟󸦨󱴤󱤾󳮜󹤗󵭡󵛃󸣚󱛷󵷔󱴹󴬖󲂳󹆤󸦨󱴤󵷔󱴹󴬖󲂳󹆤󲛫󴽯󱨍󾖜

󱪸󶽰󱤾󳮜󸒎󹱎󹤗󵭡󵛃󸣚󱛷󵷔󱴹󴬖󲂳󹆤󴋆󸦨󱴤󵷔󱴹󴬖󲂳󹆤󲛫󴽯󱨍󾖜

󱪸󶽰󱤾󳮜󸒎󹱎󹤗󵭡󵛃󸣚󵍤󳱺󹤵󹱎󵺅󾖜

Micro-Star Int’l Co.,Ltd.

The MSI logo used is a registered trademark of

Micro-Star Int’l Co., Ltd. All other marks and names

mentioned may be trademarks of their respective

owners. No warranty as to accuracy or completeness is

expressed or implied. MSI reserves the right to make

changes to this document without prior notice.

Revision History

Version 1.0, 2021/06, First release.

Technical Support

If a problem arises with your system and no solution

can be obtained from the user guide, please

contact your place of purchase or local distributor.

Alternatively, please try the following help resources

for further guidance.

yVisit the MSI website for technical guide, BIOS

updates, driver updates, and other information:

http://www.msi.com

yRegister your product at: http://register.msi.com

Table of Contents

MSI MEG X570S ACE MAX User Manual

Related Manuals