Peerless B-MIS38426 User Manual
Displayed below is the user manual for B-MIS38426 by Peerless which is a product in the Monitor Mounts & Stands category. This manual has pages.
Related Manuals
12019-08-26 #:090-9217-1
ENG
60 lb
(27 kg)
MAX
B-MIS38426
For Samsung Super Ultra Wide Curved Monitor
43": LC43J890DKNXZA
49": C49HG90DMN
49": LC49J890DKNXZA
22019-08-26 #:090-9217-1
Symbols
ENG
WARNING
ENG #
Skip to step.
ENG x3
Screws must get at least three
full turns and t snug.
ENG
Display center.
ENG
Do not overtighten screws.
ENG
Tools Needed for Assembly.
ENG
3/8"
(10mm)
ENG To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
1
2
+1/2
4
3
ENG - Before installing make sure the supporting surface will support the combined load of the equipment and
hardware. Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail.
Never exceed the Maximum Load Capacity. Always use an assistant or mechanical lifting equipment to safely lift
and position equipment. This product is intended for indoor use only. Use of this product outdoors could lead to
product failure or personal injury. Be careful not to pinch ngers when operating the mount. For support please
call customer care at 1-800-865-2112.
WARNING
Listen
ENG
17/64" 5/8", 7/16"
3/32" 2"-3"
32019-08-26 #:090-9217-1
A (1)
E (1)
desktop swivel base
support tube
Parts (Before beginning, make sure you have all parts shown below).
ENG
Parts List
Part #Description Qty
Adesktop swivel base 1 090-1821
Badaptor bracket 2 091-1211
Cright adaptor bracket 2 091-1217
Dleft adaptor bracket 2 091-1218
Esupport tube 1 091-1221
FM6 x 6mm hex set screw 2 510-9150
GM4 x 10mm socket pin screw 8 520-1060
Hslope nut 3 530-0035
I1/4-20 x 3/4" washer head screw 4 520-1321
J1/4" x 1/2" x .068 split washer 4 540-9402
K4mm allen wrench 1 560-9646
L48" foam strip 1 570-1170
M1/4-20 lock nut 4 530-1021
Nfender washer 4 540-1008
O1/4-20 x 3" threaded rod 4 520-2585
Pbase plate 1 090-1544
Qthrust washer 1 590-1287
R1/4-20 x 1.5" threaded rod 4 520-2250
S3mm allen wrench 1 560-0194
T10-32 x 1/2" set screw 2 520-1614
D (2)
C (2)
B (2)
adaptor bracket right adaptor bracket left adaptor bracket
L (1)
48" foam strip
K (1)
4mm allen wrench
J (4)
1/4" x 1/2" x .068 split washer
I (4)
1/4-20 x 3/4" washer
head screw
G (8)
M4 x 10mm socket pin
screw
F (2)
M6 x 6mm hex set
screw
S (1)
3mm allen wrench
42019-08-26 #:090-9217-1
Q (1)
thrust washer
H (3)
slope nut
P (1)
base plate
O (4)
1/4-20 x 3" threaded rod
N (4)
fender washer
M (4)
1/4-20 lock nut
R (4)
1/4-20 x 1.5" threaded rod
T (2)
10 x 32mm x 1/2"
hex set screw
52019-08-26 #:090-9217-1
ENG - Wooden mounting surface requires a minumum of 3/4" thickness to hold screen securely.
WARNING
Use base plate as a
template to mark location
of holes. Drill four holes in
square formation, aligned
to front of desk.
1
Threaded rods
must fasten a
minimum of three
turns.
ENG
22-1
O (4)
Q
E
P
Drill 2" to 3" cord
managment hole in the
center of the square
formation.
1-1
Turn base
upside down.
ENG
ENG ENG
A
17/64"
OR R (4)
x3
Front of desk
ENG Front of desk
ENG
2"-3"
A
62019-08-26 #:090-9217-1
60°
0°
120°
180°
210°
210°
240°
240°
30°
30°
60°
0°
120°
180°
40°
240
°
240°
40°
210°
210°
240°
240°
40°
Swivel restriction: refer to detail 1 through 4. Fasten two set screws
where indicated below to the outside of desired angle in steel base.
Note: set screws must be bottomed out into base.
ENG
3
Front
ENG
3/32"
Detail 1
Detail 2
Detail 3
Detail 4
A
EQ
72019-08-26 #:090-9217-1
4
4-1
ENG - Make sure that the supporting surface will safely support the combined load of the equipment and all
attached hardware and components.
WARNING
ENG - Installations to desktops that have a gap between two supporting boards are not acceptable mounting
surfaces for the desktop swivel mount.
CAUTION
M (4)
P
N (4)
A
Q
E
Align plate with threaded rods.
Note: Washer must be centered.
ENG
Align base assembly with
supporting surface and base
pattern facing the front as
shown. Tighten four fender
washers with four lock nuts
in the sequenced pattern
at minimum ush with the
bottom of the threaded rods.
ENG
Front
ENG Front
ENG
14
32
7/16"
(11mm)
82019-08-26 #:090-9217-1
H
H
5
Bottom of desk
ENG
O
5-2
Bottom of desk
ENG Bottom of desk
ENG
Leave space
between
slope nuts.
ENG
Tightening
slope nut
ENG
Optional: for added security replace two of the
washers and locknuts with slope nuts. Hand
tighten slope nuts onto two of the threaded rods
until snug against bottom of desk as shown.
ENG
Insert an open end wrench
between both slope nuts and tighten as shown.
After top slope nut is secure remove bottom slope
nut as shown.
ENG
5-1
5-3
After slope nut is
secure, remove bottom
slope nut as shown.
ENG
5/8"
Thread another slope nut upside-down,
about two turns from rst slope nut as
shown. Avoid jamming both slope nuts
together, doing so may make it dicult
to remove slope nut used for tightening.
ENG
92019-08-26 #:090-9217-1
66-1
6-2
B (2)
J (4)
F(2)
3/8"
(10mm)
I (4)
S
E
10 2019-08-26 #:090-9217-1
7
Note orientation of tab
ENG
Bottom display
ENG
Top display
ENG
Note orientation of tab
ENG
7-1
Samsung Super Ultra Wide Curved Monitor
43" (LC43J890DKNXZA), 49" (C49HG90DMN), 49" (LC49J890DKNXZA)
sold separately
ENG
11 2019-08-26 #:090-9217-1
Bottom display
Top display
8
D
C
Bottom display
ENG
Top display
ENG
K
D
C
G (4)
G(4)
8-1
12 2019-08-26 #:090-9217-1
9
L
Attach foam strip to the top edge of
bottom display.
ENG
L
L
13 2019-08-26 #:090-9217-1
10
Attach top display rst.
ENG
Attach bottom display.
ENG
10-1
Top view
ENG
C
B
D
Top view
ENG
C
B
D
14 2019-08-26 #:090-9217-1
11
11-1
QUICK RELEASE; Pull knobs to disengage.
ENG
Support display, tilt forward.
ENG
ENG Must support weight/front of display when disengaging
quick release knobs from support tube.
WARNING
15 2019-08-26 #:090-9217-1
Optional: cable management
ENG
12
Peerless Industries, Inc. (“Peerless-AV”) warrants to original end-users that each Peerless-AV® mounting product will be free from defects
in material and workmanship, under normal use, for the applicable warranty period (from date of the original installation of the product).
At its option, Peerless-AV will repair or replace, or refund the purchase price of, any product which fails to conform with this warranty.
Any implied warranty of merchantability or tness for a particular purpose shall be limited to the period of the
express warranty set forth below.
In no event shall Peerless-AV be liable for incidental or consequential damages, whether or not secured by a
security device which may be included with the product.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion of incidental or consequential damages, so
the above limitation and/or the above exclusion may not apply to you.
This warranty does not cover damage caused by incorrect selection, installation or the failure to follow Peerless-AV instructions or
warnings when installing, using or storing the product.
This warranty gives specic legal rights, and you may also have other rights which vary from state to state. To make a warranty claim in
North America, contact Peerless-AV customer care at 1-800-865-2112. See complete global warranty information for regions outside North
America at www.peerless-av.com/en-uk/customer-care/warranties-returns.
LIMITED FIVE-YEAR WARRANTY
Peerless-AV Europe
Unit 3 Watford Interchange,
Colonial Way, Watford, Herts,
WD24 4WP, United Kingdom
Customer Care
44 (0) 1923 200 100
www.peerless-av.com
© 2019, Peerless Industries, Inc.
Peerless-AV de Mexico
Ave de las Industrias 413
Parque Industrial Escobedo
Escobedo N.L Mexico 66062
Servicio al Cliente
01-800-849-65-77
www.peerless-av.com
© 2019, Peerless Industries, Inc.
Peerless-AV
2300 White Oak Circle
Aurora, IL 60502
Email: tech@peerlessmounts.com
Ph: (800) 865-2112
Fax: (800) 359-6500
www.peerless-av.com
© 2019, Peerless Industries, Inc.