Peerless DS-LEDL27-4X4 User Manual
Displayed below is the user manual for DS-LEDL27-4X4 by Peerless which is a product in the Signage Display Mounts category. This manual has pages.
Related Manuals
12020-03-17 #:146-9043-1
ENG
DS-LEDL27 Series
*Actual conguration may vary
22020-03-17 #:146-9043-1
Symbols
ENG
WARNING
ENG
Do not overtighten screws.
ENG
Tools Needed for Assembly.
ENG
5/32"
(4mm)
ENG - This product is designed to be installed on plywood walls. Hardware is included for plywood installation.
Before installing make sure the supporting surface will support the combined load of the equipment and
hardware. Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail.
Never exceed the Maximum Load Capacity. Always use an assistant or mechanical lifting equipment to safely lift
and position equipment. This product is intended for indoor use only. Use of this product outdoors could lead to
call customer care at 1-800-865-2112.
WARNING
3/8"
(10mm)
3/8"
(10mm)
#
Skip to step.
ENG
2.5mm
Wear anti-static gloves.
ENG
1
2
ENG To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
4
+1/2
3
32020-03-17 #:146-9043-1
This page intentionally left blank.
ENG
42020-03-17 #:146-9043-1
H
IJL M5 x 5mm
set screw
#14 x 1.75"
wood screw M5 x 8mmM5 x 12mm
A B C
left column right column inside column
Parts List
Description
Aleft column
Bright column
Cinside column
Dvertical spacer
Ehorizontal spacer
Fextrusion connector
G3mm allen wrench two-tip T-handle
HM5 x 5mm set screw
I#14 x 1.75" wood screw
JM5 x 8mm
Kwall plate shim
LM5 x 12mm
Mtop horizontal asy
Nbottom horizontal asy
Otop left horizontal asy
Ptop right horizontal asy
Qbottom left horizontal asy
Rbottom right horizontal asy
Parts (Before beginning, make sure you have all parts shown below).
ENG
M
N
top horizontal asy
bottom horizontal asy
K
wall plate
shim
E
horizontal
spacer
F
extrusion
connector
D
vertical spacer
G
3mm allen wrench
two-tip T-handle
52020-03-17 #:146-9043-1
O P
Q R
top left
horizontal asy
top right
horizontal asy
bottom left
horizontal asy
bottom right
horizontal asy
62020-03-17 #:146-9043-1
1-1
Optional: If connecting two top horizontal extrusions,
ENG
Remove and save hardware.
ENG
M,O
M,P
1-2
Use extrusion connectors to connect top horizontal
extrusions.
ENG
F (4) H (8)
G
2.5mm
M,P
M,O
72020-03-17 #:146-9043-1
2-1
Optional: If connecting two bottom horizontal
ENG
Remove and save hardware.
ENG
N,R
N,Q
1-3
Replace one hook-on bracket in between connected
extrusions.
ENG
Use saved hardware.
ENG
G
G
M,P
M,O
82020-03-17 #:146-9043-1
N,R
N,R
N,Q
N,Q
2-2
Use extrusion connectors to connect bottom
horizontal extrusions.
ENG
H (6)
F (3)
2-3
Replace one hook-on bracket in between connected
extrusions.
ENG
Use saved hardware.
ENG
G
2.5mm
92020-03-17 #:146-9043-1
3-1
Use a laser level to keep mounting holes
level.
ENG
3
ENG - When installing Peerless wall mounts on a wood stud wall covered with plywood, verify that the wood
studs are a minimum of 2" x 4" nominal size and plywood is a minimum Grade BC, 1/2" (13 mm) thick. Plywood
may be covered by gypsum board (drywall) up to 5/8" thick.
WARNING
10 2020-03-17 #:146-9043-1
3-2
Level top horizontal extrusion and mark
mounting holes on plywood (must be
minimum Grade BC, 1/2" (13mm) thick.)
ENG
N,P
display tile
7/8" (22mm) minimum
for mounting clearance
x"
Video Wall
Rows Dimension x"
12.75"
22.77"
32.78"
42.43"
52.32"
62.35"
72.23"
82.13"
11 2020-03-17 #:146-9043-1
3-3
Drill mounting holes into supporting surface
(1.75" (44mm) minimum depth required).
ENG
5/32"
(4mm)
1.75"
(44mm)
5/32"
(4mm)
3-4
Level extrusion. Install using wood screws
provided.
ENG
3/8"
(10mm)
Maximum 80 in. • lb (9 N.M.).
ENG
I (5)
N,P
12 2020-03-17 #:146-9043-1
3-5
horizontal extrusion.
ENG
3/8"
(10mm)
ENG
D
I
M,O
D (2)
I (2)
13 2020-03-17 #:146-9043-1
3-6
Use third vertical spacer to align bottom
then mark mounting holes on plywood (must be
minimum Grade BC, 1/2" (13mm) thick.)
ENG
58.68"
(149cm)
D
ENG
D
N,Q
N,R
14 2020-03-17 #:146-9043-1
3-8
Use third vertical spacer to align bottom
spacer, then install using wood screws
provided.
ENG
3/8"
(10mm)
Maximum 80 in. • lb (9 N.M.).
ENG
3-7
Drill mounting holes into supporting surface
(1.75" (44mm) minimum depth required).
ENG
5/32"
(4mm)
1.75"
(44mm)
5/32"
(4mm)
I (5)
N,R
15 2020-03-17 #:146-9043-1
3-9
Remove vertical spacer.
ENG
3/8"
(10mm)
D (2)
I (2)
16 2020-03-17 #:146-9043-1
4-1
Hook on and secure outer vertical columns.
"L" and "R" markings designate left and right
column.
ENG
A
B
J (8)
Tighten hardware.
ENG
G
17 2020-03-17 #:146-9043-1
4-2
Hook on and secure all inside vertical
columns.
ENG
C (4)
Tighten hardware.
ENG
J (16)
G
18 2020-03-17 #:146-9043-1
5-1
Loosen hardware on vertical columns.
ENG G
19 2020-03-17 #:146-9043-1
5-2
Tighten.
ENG
Tighten.
ENG
Plumb and level outer columns, then tighten
hardware. Tighten hardware on four corner wall
plates.
ENG G
20 2020-03-17 #:146-9043-1
Tighten.
ENG
Loosen.
ENG
Optional leveling for bowed walls
ENG
Insert.
ENG
K
5-3
Tie a string between top slots on outer
columns in order to level the depth of each
vertical column.
ENG
Loosen, adjust, tighten.
ENG
G
21 2020-03-17 #:146-9043-1
Tie a string between bottom slots on outer
columns in order to level the depth of each
vertical column.
ENG
Loosen, adjust, tighten.
ENG
5-4
Tighten.
ENG
Loosen.
ENG
Optional leveling for bowed walls
ENG
Insert.
ENG
K
G
22 2020-03-17 #:146-9043-1
5-5
With the string still attached, level the height of
each column
ENG
Tighten or loosen to adjust height.
ENG
G
23 2020-03-17 #:146-9043-1
E (2)
5-6
Tighen column hardware after spacing. Start from
the left column.
ENG G
24 2020-03-17 #:146-9043-1
5-7
spacers until all are level. Tighen column hardware
after spacing
ENG G
E (2)
25 2020-03-17 #:146-9043-1
5-8
Remove all spacers.
ENG
E (2)
26 2020-03-17 #:146-9043-1
6-1
bracket orientation as shown.
ENG G
display tile
wall
2.65"
(67mm)
MAX
2.25"
(57mm)
MIN
display tile
wall
3.05"
(77mm)
MAX
2.60"
(66mm)
MIN
27 2020-03-17 #:146-9043-1
6-2
Level L brackets and mark mounting holes
on plywood (must be minimum Grade BC,
1/2" (13mm) thick.)
ENG
28 2020-03-17 #:146-9043-1
6-3
Drill mounting holes into supporting surface
(1.75" (44mm) minimum depth required).
ENG
5/32"
(4mm)
1.75"
(44mm)
5/32"
(4mm)
6-4
Level L brackets. Install using wood
screws provided.
ENG
3/8"
(10mm)
Maximum 80 in. • lb (9 N.M.).
ENG
I (20)
29 2020-03-17 #:146-9043-1
6-5
Tie a string between center slots on outer column
in order to level the depth of each vertical column.
ENG G
30 2020-03-17 #:146-9043-1
6-6
Adjust depth, then remove string.
ENG
Loosen, adjust, tighten.
ENG
G
31 2020-03-17 #:146-9043-1
7-1
ENG Display not included.
1/8"
(3mm)
L (4)
x3
G
32 2020-03-17 #:146-9043-1
7-2
ENG Attach display, tighten connecting hardware, and run
cables one at a time starting from the bottom left.
1
2345
G
33 2020-03-17 #:146-9043-1
7-3
6
11
16
21
7
12
17
22
8
13
18
23
9
14
24
19
10
15
25
G
34 2020-03-17 #:146-9043-1
10
5
9
4
8
32
7
1
8
ENG To remove, start from the top right. G
35 2020-03-17 #:146-9043-1
This page intentionally left blank.
ENG
Peerless-AV Europe
Unit 3 Watford Interchange,
Colonial Way, Watford, Herts,
WD24 4WP, United Kingdom
Customer Care
44 (0) 1923 200 100
www.peerless-av.com
© 2020, Peerless Industries, Inc.
Peerless-AV América Latina
Av. de las Industrias 413
Parque Industrial Escobedo
General Escobedo N.L., México 66062
Servicio al Cliente
01-800-849-65-77
www.peerless-av.com
© 2020, Peerless Industries, Inc.
Peerless-AV
2300 White Oak Circle
Aurora, IL 60502
Email: tech@peerlessmounts.com
Ph: (800) 865-2112
www.peerless-av.com
© 2020, Peerless Industries, Inc.
www.peerless-av.com/warranty
Warranty Garantía Garantie Garantie Garantie
Garanzia Záruka Záruka Garantia
ENG ESP DEU NEL
ITL SLK POR TÜR