Parts List.................................................................................................................................................................................3

Installation to Double Wood Stud Wall ...................................................................................................................................4

Installation to Solid Concrete or Cinder Block ........................................................................................................................5

Installation to Metal Stud Wall ................................................................................................................................................6

Adhesive Strips and Attach CPU to Wallplate.........................................................................................................................7

Attaching Adapter Plate to Display .........................................................................................................................................8

Attaching Adapter Plate to Wall Plate and Accessing CPU ....................................................................................................9

Tools Needed for Assembly

• stud ﬁ nder ("edge to edge" stud ﬁ nder is recommended)

• phillips screwdriver

• drill

• 5/16" (8 mm) bit for concrete and cinder block wall

• 5/32" (4 mm) bit for wood stud wall

• level

• 3/8" (10 mm) Socket

• Socket Wrench

• 1/2" (13 mm) bit for metal stud wall

• 7/16" (11 mm) Socket

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US

customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact

your local distributor.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never exceed the Maximum Load Capacity. See page one.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of

an "edge to edge" stud ﬁ nder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws ﬁ rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal

injury.

• This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION HARDWARE REQUIRED

• Wood Stud Included

• Wood Beam Included

• Solid Concrete Included

• Cinder Block Included

• Metal Stud Included

• Brick Contact Qualiﬁ ed Professional

• Other or unsure? Contact Qualiﬁ ed Professional

WARNING

3 of 9 ISSUED: 12-16-11 SHEET #:125-9272-3 (2017-03-15)

Before you begin, make sure all parts shown are included with your product.

Parts may appear slightly different than illustrated.

EFGHI JK

Parts List

Part#Description Qty

Awall plate 1 145-1482

Badapter plate 1 145-1461

C#14 x 2.5" wood screw 6 5S1-015-C03

Dconcrete anchor 6 590-0320

EM8 x 12mm phillips screw 4 520-9571

FM8 x 25mm phillips screw 4 520-1031

GM5 x 12mm phillips screw 4 520-1027

HM6 x 12mm phillips screw 4 520-1128

Ispacer 8 600-1215

J5/16 SAE ﬂ at washer 8 540-9406

K3/4" x 3/16" x 10" adhesive strip 2 570-1029

Lcable tie 4 560-9711

M4mm security allen wrench 1 560-9646

N1/4-20 x 2.5" phillips screw 6 520-9521

O1/4" SEA washer 6 540-9440

Ptoggler 6 560-9708

QM5 x 12mm socket pin serrated head

washer screw 6 510-1064

Radapter bracket 2 145-1463

S1/4-20 nylock nut 4 530-9413

T1/4-20 x 1.5 ﬂ at head bolt (not used) 6 520-1264

UM6 x 25mm phillips screw 4 520-1208

4 of 9 ISSUED: 12-16-11 SHEET #:125-9272-3 (2017-03-15)

Installation to Double Wood Stud Wall

Wall plate (A) can be mounted to two studs that are 16" apart. Use a stud ﬁ nder to locate the edges of the studs.

Use of an edge-to-edge stud ﬁ nder is highly recommended. Based on their edges, draw a vertical line down

each stud’s center. Place wall plate on wall as a template. Level plate, and mark the center of the six mounting

holes. Make sure that the mounting holes are on the stud centerlines. Drill six 5/32" (4 mm) dia. holes 2-1/2"

(64 mm) deep. Make sure that the wall plate is level, secure it using six #14 x 2.5" wood screws (C) as shown.

Skip to step 2

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

• Tighten wood screws so that wall plate is ﬁ rmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud ﬁ nder

is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-

ers are responsible to provide hardware for other types of mounting situations.

WARNING

STUD

5 of 9 ISSUED: 12-16-11 SHEET #:125-9272-3 (2017-03-15)

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid

part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 speciﬁ ca-

tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to

avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-

ware and components.

WARNING

solid concrete

C (6)

D (6)

cinder block

• Tighten screws so that wall plate is ﬁ rmly attached,

but do not overtighten. Overtightening can damage

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Always attach concrete anchors directly to load-

bearing concrete.

• Never attach concrete anchors to concrete covered

with plaster, drywall, or other ﬁ nishing material. If

mounting to concrete surfaces covered with a ﬁ nish-

ing surface is unavoidable, the ﬁ nishing surface must

be counterbored as shown below. Be sure concrete

anchors do not pull away from concrete when tight-

ening screws. If plaster/drywall is thicker than 5/8",

custom fasteners must be supplied by installer.

WARNING

CUTAWAY VIEW

INCORRECT CORRECT

wall plate

wall plate concrete

plaster/

dry wall

concrete

plaster/

dry wall

Make sure that wall plate (A) is level, use it as a

template to mark six mounting holes. Drill six 5/16"

(8 mm) dia. holes to a minimum depth of 2.5"

(64 mm). Insert anchors (D) in holes ﬂ ush with wall

as shown.

Place wall plate over anchors and secure with

six #14 x 2.5" screws (C). Level, then tighten all

fasteners.

Skip to step 2

Drill holes and insert anchors (D).

Place plate (A) over anchors (D) and secure with screws (C).

Tighten all fasteners.

concrete

surface

Installation to Solid Concrete or Cinder Block

6 of 9 ISSUED: 12-16-11 SHEET #:125-9272-3 (2017-03-15)

Using a stud ﬁ nder, locate and mark the edges of the metal stud used in mounting this product. Use of an edge

to edge stud ﬁ nder is highly recommended. Use a level to draw a level, vertical line down the center of the stud.

Level wall plate, and mark the center of the six mounting holes. Make sure that the mounting holes are on the stud

centerlines. Drill six 1/2" holes through drywall and metal studs. NOTE: It may be necessary to drill 5/32" pilot holes

prior to drilling 1/2" holes. Install togglers (P) as shown in ﬁ gure 1.1. Loosely fasten wall plate to wall using six

1/4-20 x 2-1/2" screws (N) and six 1/4" washers (O) as shown in ﬁ gure 1.2. Level, hold, and then tighten all screws.

• Drywall must be 1/2" or thicker, and metal stud must be 24 gauge or thicker.

• Make sure that the wall will safely support the combined load of the equipment and all attached hardware and

components.

• Make sure that togglers are anchored into the center of the studs. The use of an "edge to edge" stud ﬁ nder is highly

recommended.

WARNING

Installation to Metal Studs

ﬁ g. 1.2

Rotate toggler (P) clockwise to wedge it

against inside walls of metal stud.

Push into hole.

Pivot end of toggler (P).

Slide plastic cap forward while pulling back

ﬁ rmly on ring.

Break off excess.

ﬁ g. 1.1

drill

1/2"

hole

7 of 9 ISSUED: 12-16-11 SHEET #:125-9272-3 (2017-03-15)

Place adhesive strips (K) on the wall plate (A) in location that will allow the most contact with CPU

as shown in ﬁ gure 2.1.

Note: Placement of adhesive strips will vary depending on size of CPU as shown in ﬁ gure 2.2

NOTE: Safety belt may need to be loosened to attach CPU to wall plate (A).

Press CPU against adhesive strips on wall plate and tightly secure safety belt against CPU.

CPU

SAFTEY

BELT

ﬁ g. 2.1

Placement of Adhesive Strips

Attach CPU to Wall Plate

ﬁ g. 2.2

FRONT VIEW

8 of 9 ISSUED: 12-16-11 SHEET #:125-9272-3 (2017-03-15)

• If screws don't get three complete turns in the screen

inserts or if screws bottom out and bracket is still

not tightly secured, damage may occur to screen or

product may fail.

WARNING

Use ﬁ gure 5.1 to determine placement of adapter brackets (R) on the adapter plate (B) using

1/4-20 nylock nut (S) as shown.

NOTE: For displays with 400mm x 400mm VESA hole patterns, adapter brackets (R) are not used.

NOTE: For displays with 800mm or 600mm VESA hole pattern, use ACC-V800X (sold separately).

DEDICATED

MOUNTING PATTERNS

15.75"

(400 mm)

7.87"

(200 mm)

11.81"

(300 mm)

7.87"

(200 mm)

3.94"

(100 mm)

1.97"

(50 mm)

BACK VIEW

DISPLAY NOT SHOWN

FOR CLARITY

11.81"

(300 mm)

M8 x 25 mm screws (F)

with 5/16" washers (J)

M6 x 12 mm screws (H)

with 1/4" washers (O)

M6 x 25 mm screws (U)

with 1/4" washers (O)

M8 x 12 mm screws (E)

E, F, G, U, or H

J or O

Attaching Adapter Plate to Display

Determine hole pattern of display and fasteners used.

Hand thread screws (E, F, G, U, or H) through washers (J or O) and

adapter brackets (R) into screen as shown in ﬁ gure 4.1.

M5 x 12 mm screws (G)

with 1/4" washers (O)

ﬁ g. 4.1

ﬁ g. 5.1

PLP

ADAPTER

PLATE

9 of 9 ISSUED: 12-16-11 SHEET #:125-9272-3 (2017-03-15)

Thread two M5 x 15 mm socket pin screws (Q) into bottom holes of wall plate (A). Guide hook slots of adapter plate

(B) onto screws (Q), while supporting weight of screen, align top holes of wall plate and adapter bracket to the

desired tilt angle and secure with two M5 x 15 mm socket pin screws (Q) as shown in ﬁ gure 6.2. Tighten all screws

securely. Using wrench (M) secure M5 x 15mm socket pin screw (Q) to "TOP HOLE" when not using ﬁ xed stop

positions.

Attaching Adapter Plate to Wall Plate

NO TILT

5° TILT

10° TILT

HOOK

SLOTS

BOTH SIDES

NOTE: When display is in portrat position (as shown in ﬁ g. 7.1) make sure that top screw (Q) is in the foward "10°

ﬁ xed stop position"

Using wrench (M) loosen top two M5 x 15 mm socket pin screws (Q) 1/4 turn and temporarily remove bottom two

M5 x 15 mm socket pin screws (Q) on adapter plate (A) as shown in ﬁ gure 7.2. Swing screen forward and swing

support brackets downward into adapter plate (B) to brace screen in open position as shown in ﬁ gure 7.3.

Accessing CPU

SUPPORT BRACKETS

(BOTH SIDES)

LOOSEN 1/4 TURN ON

BOTH SIDES

REMOVE

ﬁ g. 7.2 ﬁ g. 7.3

WALL NOT SHOWN FOR CLARITY

Q (2)

ﬁ g. 6.1 ﬁ g. 6.2

BOTH SIDES BOTH SIDES

ﬁ g. 7.1

BOTH SIDES

USE TOP HOLE

WHEN NOT USING

0°, 5°, OR 10° FIXED

STOP POSITIONS

TOP HOLE