Peerless HP447 User Manual
Displayed below is the user manual for HP447 by Peerless which is a product in the TV Mounts category. This manual has pages.
Related Manuals
Max Load Capacity: 75 lb (34 kg)
Installation and Assembly -
Desktop Swivel Mount
For 26" to 47" Flat Panel Displays with VESA 200 x 100 or
200 x 200 Mounting Hole Patterns
Models: HP447
ISSUED: 2012-06-19 SHEET #:125-9327-5 (2017-10-20)
®
2 of 7 ISSUED: 2012-06-19 SHEET #:125-9327-5 (2017-10-20)
NOTE: Read instruction sheet before you start installation and assembly.
NOTE: Some parts may appear slightly different than illustrated.
A B
C
D E
F
GH
IJ
K
L
M
P Q R S
T
N
O
Tools Needed for Assembly
• drill • 5/8" open box wrench
• 17/64" drill bit
• 3/8" socket wrench
• 3/32" allen wrench
Parts List
Part #Description Qty
Asupport tube 1 091-1036
Bbase backer plate 1 090-1544
Cdesktop swivel base 1 090-1821
Dadapter plate 1 091-1030
Ethrust washer 1 590-1287
Fslope nut 3 530-0035
G1/4-20 x 3-4" hex head screw 2 520-1321
HM4 x 12mm serrated socket pin screw 4 510-1079
I4mm allen wrench 1 560-9646
J10-32 x 1/2" set screw 2 520-1614
Kfender washer 4 540-1008
L1/4-20 x 3" threaded rod 4 520-2585
M1/4-20 lock nut 4 530-1021
NM6 x 12mm socket pin screw 4 510-1050
OM8 x 15mm socket pin screw 4 520-1068
P#10 SAE at washer 4 540-9400
QM8 x 25mm socket pin screw 4 520-1101
RM8 x 35mm socket pin screw 4 520-1994
Swasher 8 540-9406
Tspacer 4 600-1215
3 of 7 ISSUED: 2012-06-19 SHEET #:125-9327-5 (2017-10-20)
Turn base (C) upside down insert support tube (A),
and thrust washer (E) as shown below.
A
C
E
g. 3.1
23
Turn base (C) upside down and insert four threaded
rods (L) into base (C), as shown below.
NOTE: Threaded rods must fasten a minimum
of three turns.
L
C
g. 2.1
• Wooden mounting surface requires a minimum of 3/4" thickness to hold screen securely.
WARNING
1Use base backer plate (B) as a template to mark location of holes. Drill four holes using a 17/64'' drill bit in a
square formation. In the center of the square formation drill 2" to 3" cord management hole.
BSQUARE FORMATION
CORD MANAGEMENT
CUT-OUT FRONT OF SCREEN
BOTTOM VIEW
4 of 7 ISSUED: 2012-06-19 SHEET #:125-9327-5 (2017-10-20)
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components
WARNING
Mounting using Non-Security....................................................................Step 5 Page 5
CAUTION
• Installations to desktops that have a gap between two supporting boards are not acceptable mounting surfaces
for the HP line of desktop swivel mounts.
Mounting using Security Slop Nuts (Optional) .......................................Step 7 Page 5
Mounting to Support Surface
g. 4.1 g. 4.2
60°
120°
LOCK AT 0°
Refer to g. 4.1 and 4.2, select the desired swivel degree. Using a 3/32" allen wrench, fasten two set screws (J)
where indicated below to the outside of desired angle in steel base (C).
NOTE: Set screws (J) must be bottomed out into base.
C
A
Swivel Restriction
4
180°
240°
240°
210°
40°
30°30°
210°
FRONT
FRONT
5 of 7 ISSUED: 2012-06-19 SHEET #:125-9327-5 (2017-10-20)
2
3
1
4
5Line up backer plate (B) with threaded rods (L).
NOTE: Thrust washer (E) must be centered.
FRONT OF
SCREEN
Detail 1
B
L
g. 5.1
6
C
FRONT OF
SCREEN
E
Tighten in sequenced pattern using four fender
washers (K) and four lock nuts (M) as shown in
Figure 6.1. The 1/4-20 locknuts (M) should at least be
ush with the bottom of the threaded rods (L).
Line up base assembly (step 5), through supporting
surface with pattern of base (C) facing the front as
shown in Detail 1.
g. 6.1
K
M
Mounting using Non-Security
Mounting using Security Slope Nuts (Optional)
Detail 4
TIGHTENING
SLOPE NUT (F)
F
5/8" OPEN BOX WRENCH
TIGHTENING
SLOPE NUT (F)
L
L
F
Detail 2
Detail 3
F
For added security replace two of
the washers and locknuts with slope
nuts.
Hand tighten slope nuts (F) onto
two of the thread rods (L) until
snug against bottom of table as
shown in Detail 2.
Thread another slope nut (F)
upside-down, about two turns from
rst slope nut (F) as shown in Detail
3.
Insert a 5/8" open box wrench
between both slope nuts (F) and
tighten
as shown in Detail 4.
7
BOTTOM OF DESK
BOTTOM OF DESK
NOTE: Avoid jamming both slope nuts (F) together,
doing so may make it difcult to remove slope nut
used for tightening.
After slope nut is secure remove bottom slope nut.
LEAVE SPACE
IN BETWEEN
SLOPE NUTS
6 of 7 ISSUED: 2012-06-19 SHEET #:125-9327-5 (2017-10-20)
NOTE: Adapter plate support box (D) can be ipped either way to allow necessary screen clearance.
For best results, have screen close to desktop but not touching.
Adapter plate (D) is adjustable up to 7.87'' (200 mm) " at .984" (25mm) increments. Attach adapter plate (D) to
support tube (A) as shown. Fasten two 1/4-20 x 3/4" hex head screws (G) through adapter plate (D) and support
tube (A), as shown.
8
SUPPORTING SURFACE NOT SHOWN FOR CLARITY
g. 7.2g. 7.1
G
Optional
A
G
A
D
D
• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not
tightly secured, damage may occur to screen or product may fail.
WARNING
1/8"
FOR SCREENS WITH VESA 200 X 200 PATTERN SHOWN
SCREEN
D
D
SCREEN
Fasten two socket pin screws (H, N, O, Q, or R) into top mounting holes in back of screen leaving 1/8" of exposed
thread as shown below. Hook exposed threads onto top of adapter plate (D) and secure using two socket pin screws
(H, N, O, Q, or R). Use of washer (S) and spacer (T) is optional. NOTE: When using socket pin screw (H), #10 at
washers (P) are required.
9
Mounting using 200 mm x 200 mm Hole Pattern
H, N, O, Q, or R
H, N, O, Q, or R
7 of 7 ISSUED: 2012-06-19 SHEET #:125-9327-5 (2017-10-20)
1/8"
FOR SCREENS WITH VESA 200 X 100 PATTERN SHOWN
SCREEN
D
D
SCREEN
Fasten two socket pin screws (H, N, O, Q, or R) into top mounting holes in back of screen leaving 1/8" of exposed
thread as shown below. Hook exposed threads onto top of adapter plate (D) and secure using two socket
pin screws (H, N, O, Q, or R). Use of washer (S) and spacer (T) is optional. NOTE: When using socket pin screw
(H), #10 at washers (P) are required.
10
H, N, O, Q, or R
H, N, O, Q, or R
Mounting using 200 mm x 100 mm Hole Pattern