Peerless LCT100S User Manual
Displayed below is the user manual for LCT100S by Peerless which is a product in the Monitor Mounts & Stands category. This manual has pages.
Related Manuals
2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com
ISSUED: 07-25-11 SHEET #: 090-9202-6 2020-03-09
Max Load Capacity: 20 lbs (9 kg)
Installation and Assembly:
Desktop Mount with Desk Clamp and Grommet for 19" - 30"
LCD Screens
Models: LCT100S
GROMMET INSTALLATION DESK CLAMP INSTALLATION
2 of 8 ISSUED: 07-25-11 SHEET #: 090-9202-6 2020-03-09
NOTE: Read entire instruction sheet before you start installation and assembly.
Tools Needed for Assembly
• phillips screwdriver
• drill
• 7/16" (11 mm) drill bit
Table of Contents
Parts List.................................................................................................................................................................................3
Installation to Mounting Surface .............................................................................................................................................4
Attaching Adapter Plate Assembly to Screen .........................................................................................................................5
Cable Management ................................................................................................................................................................6
WARNING
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
call Peerless customer care at 1-800-865-2112.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum Load Capacity. See page 1.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
power.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
3 of 8 ISSUED: 07-25-11 SHEET #: 090-9202-6 2020-03-09
Description Qt
y
Acolumn assembly 1
Badapter plate assembly 1
Cgrommet assembly 1
Dround rubber pads 2
Esquare rubber pads 2
FM4 x 12 mm phillips screw 4
GM4 x 25 mm phillips screw 4
Hspacer 4
I4 mm allen wrench 1
J2.5 mm allen wrench 1
Kcable clip 1
Lcable tie 5
Parts List
Before you begin, make sure all parts shown are included
with your product. A B
C
DE
F G H
K L
J
I
4 of 8 ISSUED: 07-25-11 SHEET #: 090-9202-6 2020-03-09
D
D
E
E
A
A
A
A
Apply four rubber pads (D, E) to bottom of column
assembly (A) as shown below. Attach column
assembly (A) to mounting surface with a maximum
thickness of 3".
Skip to step four.
1
Clamp Installation Method
Remove clamp assembly from column assembly
(A
from grommet assembly (C) and attach to column
assembly (A) with four M6 x 8 mm screws using
4mm allen wrench (I
Apply four rubber pads (D, E) to bottom of column
assembly (A) as shown below.
1
2 3
Grommet Installation Method
g. 1.1
g. 1.2
M6 X 8 MM
SCREWS
M6 X 8 MM
SCREWS
CLAMP
ASSEMBLY
MOUNTING
PLATE
A
C
Drill a 7/16" (11mm) dia. hole through mounting
surface with a maximum thickness of 3". Place
column assembly (A) on mounting surface and
secure using grommet assembly (C).
5 of 8 ISSUED: 07-25-11 SHEET #: 090-9202-6 2020-03-09
Attaching Adapter Plate Assembly to Screen
screen face side down. If screen has knobs on the back, remove them to allow the adapter plate assembly to be
attached. Place adapter plate assembly (B) on back of screen.
Choose hole pattern as shown in detail 1.
FOR DISPLAYS WITH FLAT BACKS: Attach adapter plate assembly (B) to display using four 12mm screws
(F
FOR DISPLAYS WITH RECESSED BACKS: Attach adapter plate assembly (B) to display using four 25mm
screws (G) and four spacers (H
can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to
become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns into the screen inserts or if screws bottom out and plate is still not tightly
secured, damage may occur to screen or product may fail.
WARNING
VESA 100mm
VESA 75mm
VESA 75mm VESA 100mm
DETAIL 1
4
B
B
G
H
F
g. 4.1
g. 4.2
6 of 8 ISSUED: 07-25-11 SHEET #: 090-9202-6 2020-03-09
Cables may be routed using cable clip (K).
6
B
K
A
LOCK COLLAR
SET SCREW
CABLES
Insert adapter plate assembly (B) onto column assembly (A
Tighten set screw on rear of adapter plate assembly (B) using 2.5mm allen wrench (J
5
LOCK COLLAR
g. 5.1 g. 5.2 g. 5.3
7 of 8 ISSUED: 07-25-11 SHEET #: 090-9202-6 2020-03-09
© 2020 Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
To lock down rotation, tighten set screw shown in detail 2.
To lock down tilt, tighten screw shown in detail 3.
To lock down swivel, tighten screw shown in detail 4.
7
360°
+80/-20°
SET SCREW
DETAIL 2
DETAIL 3
DETAIL 4
TILT SCREW
SWIVEL
SCREW
180°
8 of 8 ISSUED: 07-25-11 SHEET #: 090-9202-6 2020-03-09
Peerless-AV Europe
Unit 3 Watford Interchange,
Colonial Way, Watford, Herts,
WD24 4WP, United Kingdom
Customer Care
44 (0) 1923 200 100
www.peerless-av.com
© 2020, Peerless Industries, Inc.
Peerless-AV América Latina
Av. de las Industrias 413
Parque Industrial Escobedo
General Escobedo N.L., México 66062
Servicio al Cliente
01-800-849-65-77
www.peerless-av.com
© 2020, Peerless Industries, Inc.
Peerless-AV
2300 White Oak Circle
Aurora, IL 60502
Email: tech@peerlessmounts.com
Ph: (800) 865-2112
Fax: (800) 359-6500
www.peerless-av.com
© 2020, Peerless Industries, Inc.
www.peerless-av.com/warranty
Warranty Garantía Garantie Garantie Garantie
Garanzia Záruka Záruka Garantia
ENG ESP FRN DEU NEL
ITL SLK POR TÜR